ZYXEL-AS-MIB
ZyXEL Communications Corp.snmptranslate -m ZYXEL-AS-MIB -Tpsnmpwalk -v2c -c <community> -m ZYXEL-AS-MIB <host> 1.3.6.1.4.1.890Imports
| BRIDGE-MIB | BridgeId, MacAddress, Timeout |
|---|---|
| IF-MIB | ifIndex |
| Q-BRIDGE-MIB | PortList |
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP |
| SNMPv2-SMI | Bits, Integer32, IpAddress, MODULE-IDENTITY, MibIdentifier, OBJECT-IDENTITY, OBJECT-TYPE, TRAP-TYPE, TimeTicks, Unsigned32, enterprises, iso |
| SNMPv2-TC | DisplayString, PhysAddress, RowStatus, TEXTUAL-CONVENTION |
OID tree
| Name | OID | Type | Access | Status |
|---|---|---|---|---|
| Nzyxel | 1.3.6.1.4.1.890 | |||
| Nproducts | 1.3.6.1.4.1.890.1 | |||
| NaccessSwitch | 1.3.6.1.4.1.890.1.5 | |||
| !reboot | 1.3.6.1.4.1.890.1.5.0.1 | |||
notification Send a message to the manager that the system is going to reboot. The variable is the reason why the system reboots.
| ||||
| !systemShutdown | 1.3.6.1.4.1.890.1.5.0.2 | |||
notification Send a message to the manager that the system is going to shutdown. The variable is the reason that causes the system to shutdown.
| ||||
| !overheat | 1.3.6.1.4.1.890.1.5.0.3 | |||
notification Send a message to the manager that the system is overheated. The variable in the binding list is the current temperature in Celsius of the system. | ||||
| !overheatOver | 1.3.6.1.4.1.890.1.5.0.4 | |||
notification Send a message to the manager that the overheated condition is over. The variable in the binding list is the current temperature in Celsius of the system. | ||||
| !errLog | 1.3.6.1.4.1.890.1.5.0.5 | |||
notification Send a message to the manager that an error log is created in system. The variable in the binding list is the content of the error log.
| ||||
| !fanRpmLow | 1.3.6.1.4.1.890.1.5.0.6 | |||
notification Send a message to the manager that the rpm of the fan is too low. The variable in the binding list is the current rpm of the fan. | ||||
| !fanRpmNormal | 1.3.6.1.4.1.890.1.5.0.7 | |||
notification Send a message to the manager that the low-rpm condition of the fan is over. The variable in the binding list is the current rpm of the fan. | ||||
| !voltageOutOfRange | 1.3.6.1.4.1.890.1.5.0.8 | |||
notification Send a message to the manager that the voltage of the system is out of range. The variable in the binding list is the current voltage in volt of the system. | ||||
| !voltageNormal | 1.3.6.1.4.1.890.1.5.0.9 | |||
notification Send a message to the manager that the low-voltage condition is over. The variable in the binding list is the current voltage in volt of the system. | ||||
| !systemMaintenanceFailure | 1.3.6.1.4.1.890.1.5.0.10 | |||
notification Send a message to the manager that the system maintence operation fail. The variable in the variable binding indicates the problem.
| ||||
| !configChange | 1.3.6.1.4.1.890.1.5.0.11 | |||
notification Send a message to the manager that the system configuration data is changed.
| ||||
| !thermalSensorFailure | 1.3.6.1.4.1.890.1.5.0.12 | |||
| NaccessSwitchCommon | 1.3.6.1.4.1.890.1.5.1 | |||
| NaccessSwitchMgnt | 1.3.6.1.4.1.890.1.5.1.1 | |||
| SaccessSwitchSystemCurrentStatus | 1.3.6.1.4.1.890.1.5.1.1.1 | INTEGER (0..255) | RO | mandatory |
scalar · INTEGER (0..255) · read-only · mandatory This variable indicates the status of the system.
The sysCurrentStatus is a bit map represented
as a sum, therefore, it can represent multiple defects
simultaneously. The sysNoDefect should be set if and only if
no other flag is set.
The various bit positions are:
1 sysNoDefect
2 sysOverHeat
3 sysFanRpmLow
4 sysVoltageLow
5 sysThermalSensorFailure | ||||
| SaccessSwitchProblemCause | 1.3.6.1.4.1.890.1.5.1.1.2 | DisplayString | RO | mandatory |
scalar · DisplayString · read-only · mandatory The variable is the description of sytsem problem. | ||||
| SaccessSwitchSystemTemperature | 1.3.6.1.4.1.890.1.5.1.1.3 | DisplayString | RO | mandatory |
scalar · DisplayString · read-only · mandatory The variable is the current temperature in Celsius of the system. | ||||
| TaccessSwitchFanRpmTable | 1.3.6.1.4.1.890.1.5.1.1.4 | NA | mandatory | |
table · not-accessible · mandatory A table that contains rpm information about the fans. | ||||
| RaccessSwitchFanRpmEntry | 1.3.6.1.4.1.890.1.5.1.1.4.1 | NA | mandatory | |
| CaccessSwitchFanRpmIndex | 1.3.6.1.4.1.890.1.5.1.1.4.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The identity of the fan. | ||||
| CaccessSwitchFanRpmCurValue | 1.3.6.1.4.1.890.1.5.1.1.4.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current rpm of the fan. | ||||
| CaccessSwitchFanRpmMaxValue | 1.3.6.1.4.1.890.1.5.1.1.4.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The maximum rpm ever performed by the fan. | ||||
| CaccessSwitchFanRpmMinValue | 1.3.6.1.4.1.890.1.5.1.1.4.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The minimum rpm ever performed by the fan. | ||||
| CaccessSwitchFanRpmLowThresh | 1.3.6.1.4.1.890.1.5.1.1.4.1.5 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The low threshold of the rpm of the fan. If the current rpm is less than the threshold, the device will initiate the fanRpmLow trap. | ||||
| CaccessSwitchFanRpmDescr | 1.3.6.1.4.1.890.1.5.1.1.4.1.6 | DisplayString | RO | mandatory |
column · DisplayString · read-only · mandatory The description of the fan (e.g. location, function, etc.). | ||||
| TaccessSwitchVoltageTable | 1.3.6.1.4.1.890.1.5.1.1.5 | NA | mandatory | |
table · not-accessible · mandatory A table that contains voltage information about the system. | ||||
| RaccessSwitchVoltageEntry | 1.3.6.1.4.1.890.1.5.1.1.5.1 | NA | mandatory | |
row · not-accessible · mandatory A list of voltage information for each sensor. | ||||
| CaccessSwitchVoltageIndex | 1.3.6.1.4.1.890.1.5.1.1.5.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The identity of the sensor. | ||||
| CaccessSwitchVoltageCurValue | 1.3.6.1.4.1.890.1.5.1.1.5.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current voltage detected by the sensor (in milli-voltage). | ||||
| CaccessSwitchVoltageMaxValue | 1.3.6.1.4.1.890.1.5.1.1.5.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The maximum voltage ever detected by the sensor (in milli-voltage). | ||||
| CaccessSwitchVoltageMinValue | 1.3.6.1.4.1.890.1.5.1.1.5.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The minimum voltage ever detected by the sensor (in milli-voltage). | ||||
| CaccessSwitchVoltageNominalValue | 1.3.6.1.4.1.890.1.5.1.1.5.1.5 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The nominal voltage which the power should supply (in milli-voltage). | ||||
| CaccessSwitchVoltageLowThresh | 1.3.6.1.4.1.890.1.5.1.1.5.1.6 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The low threshold of the voltage. If the current voltage is less than the threshold, the device will initiate the voltageLow trap. | ||||
| CaccessSwitchVoltageDescr | 1.3.6.1.4.1.890.1.5.1.1.5.1.7 | DisplayString | RO | mandatory |
column · DisplayString · read-only · mandatory The description of the voltage (e.g. location, nominal value, etc.). | ||||
| TaccessSwitchSysTempTable | 1.3.6.1.4.1.890.1.5.1.1.6 | NA | mandatory | |
table · not-accessible · mandatory A table that contains temperature information about system. | ||||
| RaccessSwitchSysTempEntry | 1.3.6.1.4.1.890.1.5.1.1.6.1 | NA | mandatory | |
row · not-accessible · mandatory A list of temperature information for each sensor. | ||||
| CaccessSwitchSysTempIndex | 1.3.6.1.4.1.890.1.5.1.1.6.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The identity of the sensor. | ||||
| CaccessSwitchSysTempCurValue | 1.3.6.1.4.1.890.1.5.1.1.6.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current temperature detected in Celsius by the sensor. | ||||
| CaccessSwitchSysTempMaxValue | 1.3.6.1.4.1.890.1.5.1.1.6.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The maximum temperature ever detected in Celsius by the sensor. | ||||
| CaccessSwitchSysTempMinValue | 1.3.6.1.4.1.890.1.5.1.1.6.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The minimum temperature ever detected in Celsius by the sensor. | ||||
| CaccessSwitchSysTempHighThresh | 1.3.6.1.4.1.890.1.5.1.1.6.1.5 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The high threshold of the temperature in Celsius. If the current temperature is higher than the threshold, the device will initiate the overheat trap. | ||||
| CaccessSwitchSysTempDescr | 1.3.6.1.4.1.890.1.5.1.1.6.1.6 | DisplayString | RO | mandatory |
column · DisplayString · read-only · mandatory The description of the temperature sensor (e.g. location, function, etc.). | ||||
| SaccessSwitchMaintenance | 1.3.6.1.4.1.890.1.5.1.1.7 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory The managed object is for system maintenance. When the EMS
wants to trigger the system maitenance operation, the EMS
shall send SNMP-SET message to set the corresponding bit value
to be 1. The various bit positions are:
BIT 1: config save
BIT 2: reset
BIT 3: local loopback test
BIT 4: remote loopback test | ||||
| SaccessSwitchMaintenancePort | 1.3.6.1.4.1.890.1.5.1.1.8 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory The port which the maintenance operation should be performed on. The value of 0 means the maintenance should be performed on the system. | ||||
| SaccessSwitchMaxNumOfStaticVlans | 1.3.6.1.4.1.890.1.5.1.1.9 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory The maximum number of static VLANs which the system supports | ||||
| SacccessSwitchChassisId | 1.3.6.1.4.1.890.1.5.1.1.10 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory The chassis Id of the module | ||||
| SaccessSwitchSlotId | 1.3.6.1.4.1.890.1.5.1.1.11 | ASSlotNum | RW | mandatory |
scalar · ASSlotNum · read-write · mandatory The slot Id of the module | ||||
| SaccessSwitchModuleType | 1.3.6.1.4.1.890.1.5.1.1.12 | ASModuleType | RO | mandatory |
scalar · ASModuleType · read-only · mandatory The type of the module | ||||
| SaccessSwitchFWVersion | 1.3.6.1.4.1.890.1.5.1.1.13 | DisplayString | RO | mandatory |
scalar · DisplayString · read-only · mandatory The firmware version of the access switch. | ||||
| SaccessSwitchDriverVersion | 1.3.6.1.4.1.890.1.5.1.1.14 | DisplayString | RO | mandatory |
scalar · DisplayString · read-only · mandatory The driver version of the access port in this access switch | ||||
| SaccessSwitchModemCodeVersion | 1.3.6.1.4.1.890.1.5.1.1.15 | DisplayString | RO | mandatory |
scalar · DisplayString · read-only · mandatory The modem code version of the access port in this access switch | ||||
| SaccessSwitchDSLConfOps | 1.3.6.1.4.1.890.1.5.1.1.16 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory The managed object is for xDSL line configuration. When the EMS
wants to issue the desired operation, the EMS
shall send SNMP-SET message to set the corresponding bit value
to be 1. The various bit positions are:
BIT 1: enable port
BIT 2: disable port
BIT 3: set DSL mode
BIT 4: set profile | ||||
| SaccessSwitchDSLConfTarget | 1.3.6.1.4.1.890.1.5.1.1.17 | OCTET STRING | RW | mandatory |
scalar · OCTET STRING · read-write · mandatory The managed object is used for identify the target on which
the line configuration should be performed. The target is encoded
as:
Byte 1~4: reserved
Byte 5~7: each octet specifies a set of eight ports, with the first
octet specifying ports 1 through 8, etc.
Byte 8~10: reserved | ||||
| SaccessSwitchDSLConfProfileName | 1.3.6.1.4.1.890.1.5.1.1.18 | DisplayString (SIZE (1..31)) | RW | mandatory |
scalar · DisplayString (SIZE (1..31)) · read-write · mandatory The DSL profile name | ||||
| SaccessSwitchDSLConfMode | 1.3.6.1.4.1.890.1.5.1.1.19 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory The DSL mode. The semantic for each bit is: Bit 1: ADSL, G.lite Bit 2: ADSL, G.dmt Bit 3: ADSL, T1.413 Bit 4: ADSL, Auto | ||||
| TasPacketForwardingTable | 1.3.6.1.4.1.890.1.5.1.1.20 | NA | mandatory | |
table · not-accessible · mandatory This table includes the configuration of packet forwarding. | ||||
| RasPacketForwardingEntry | 1.3.6.1.4.1.890.1.5.1.1.20.1 | NA | mandatory | |
| CasPacketForwardingPortList | 1.3.6.1.4.1.890.1.5.1.1.20.1.1 | PortList | RW | mandatory |
column · PortList · read-write · mandatory The list defines the ports to which the packets will be forwarded. | ||||
| SasDhcpRelayEnable | 1.3.6.1.4.1.890.1.5.1.1.21 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Enable/disable DHCP relay function.
| ||||
| SasDhcpRelayOption82Enable | 1.3.6.1.4.1.890.1.5.1.1.22 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Enable/disable the relay agent information option.
| ||||
| SasDhcpRelayOption82Info | 1.3.6.1.4.1.890.1.5.1.1.23 | DisplayString | RW | mandatory |
scalar · DisplayString · read-write · mandatory User specific relay agent information. | ||||
| SasMaxNumOfDhcpServers | 1.3.6.1.4.1.890.1.5.1.1.24 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory The maximum number of DHCP servers. | ||||
| TasDhcpServerTable | 1.3.6.1.4.1.890.1.5.1.1.25 | NA | mandatory | |
table · not-accessible · mandatory A table that contains DHCP server information. | ||||
| RasDhcpServerEntry | 1.3.6.1.4.1.890.1.5.1.1.25.1 | NA | mandatory | |
| CasDhcpServerIp | 1.3.6.1.4.1.890.1.5.1.1.25.1.1 | IpAddress | RO | mandatory |
column · IpAddress · read-only · mandatory The IP address of the DHCP server. | ||||
| CasDhcpServerRowStatus | 1.3.6.1.4.1.890.1.5.1.1.25.1.2 | RowStatus | RW | mandatory |
column · RowStatus · read-write · mandatory The row status of the DHCP server entry. | ||||
| SasMaxNumberOfRadiusServers | 1.3.6.1.4.1.890.1.5.1.1.28 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory The max number of the RADIUS Servers. | ||||
| TasRadiusServerTable | 1.3.6.1.4.1.890.1.5.1.1.29 | NA | mandatory | |
table · not-accessible · mandatory A table that contains Radius Server information. | ||||
| RasRadiusServerEntry | 1.3.6.1.4.1.890.1.5.1.1.29.1 | NA | mandatory | |
| CasRadiusServerIndex | 1.3.6.1.4.1.890.1.5.1.1.29.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The identity of the RADIUS server. | ||||
| CasRadiusServerIp | 1.3.6.1.4.1.890.1.5.1.1.29.1.2 | IpAddress | RW | mandatory |
column · IpAddress · read-write · mandatory The IP address of the Radius Server. | ||||
| CasRadiusServerPort | 1.3.6.1.4.1.890.1.5.1.1.29.1.3 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory The UDP port of the Radius Server. | ||||
| CasRadiusSharedSecret | 1.3.6.1.4.1.890.1.5.1.1.29.1.4 | DisplayString | RW | mandatory |
column · DisplayString · read-write · mandatory The shared secret of the Radius Server. | ||||
| CasRadiusServerRowStatus | 1.3.6.1.4.1.890.1.5.1.1.29.1.5 | RowStatus | RW | mandatory |
column · RowStatus · read-write · mandatory The row status of the Radius Server entry. | ||||
| SasDot1xEnable | 1.3.6.1.4.1.890.1.5.1.1.30 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Enable/disable the 802.1x function.
| ||||
| TasDot1xPortTable | 1.3.6.1.4.1.890.1.5.1.1.31 | NA | mandatory | |
table · not-accessible · mandatory This table includes the configuration of 802.1x. | ||||
| RasDot1xPortEntry | 1.3.6.1.4.1.890.1.5.1.1.31.1 | NA | mandatory | |
| CasDot1xPortEnable | 1.3.6.1.4.1.890.1.5.1.1.31.1.1 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory The option defines if the port enables 802.1x settings.
| ||||
| CasDot1xPortControl | 1.3.6.1.4.1.890.1.5.1.1.31.1.2 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory The configuration defines the 802.1x port control type.
| ||||
| CasDot1xPortReAuthEnable | 1.3.6.1.4.1.890.1.5.1.1.31.1.3 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory The option defines if the port enables 802.1x re-authentication.
| ||||
| CasDot1xPortReAuthPeriod | 1.3.6.1.4.1.890.1.5.1.1.31.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory The configuration defines the 802.1x re-authentication period for each port. | ||||
| NaccessSwitchStats | 1.3.6.1.4.1.890.1.5.1.2 | |||
| NasMacStats | 1.3.6.1.4.1.890.1.5.1.2.1 | |||
| SasMacDisplayTarget | 1.3.6.1.4.1.890.1.5.1.2.1.1 | INTEGER | RW | |
scalar · INTEGER · read-write · current This managed object is a filter used for identify the target from which the MAC addresses are learned in macTable. The target should be IfIndex which is used for identifying subscriber ports (e.g. 300 means all ports in slot 3 and 301 means port 1 in slot 3). | ||||
| TasMacTable | 1.3.6.1.4.1.890.1.5.1.2.1.2 | NA | ||
table · not-accessible · current A table that contains information about unicast entries for which the bridge has forwarding and/or filtering information. This information is used by the transparent bridging function in determining how to propagate a received frame. | ||||
| RasMacEntry | 1.3.6.1.4.1.890.1.5.1.2.1.2.1 | NA | ||
| CasMacAddress | 1.3.6.1.4.1.890.1.5.1.2.1.2.1.1 | MacAddress | RO | |
column · MacAddress · read-only · current A unicast MAC address for which the bridge has forwarding and/or filtering information. | ||||
| CasMacPort | 1.3.6.1.4.1.890.1.5.1.2.1.2.1.2 | INTEGER | RO | |
column · INTEGER · read-only · current The port from which the mac address has been learned. | ||||
| CasMacStatus | 1.3.6.1.4.1.890.1.5.1.2.1.2.1.3 | INTEGER | RO | |
column · INTEGER · read-only · current The status of this entry.
| ||||
Traps / Notifications
- configChange
1.3.6.1.4.1.890.1.5.0.11 - errLog
1.3.6.1.4.1.890.1.5.0.5 - fanRpmLow
1.3.6.1.4.1.890.1.5.0.6 - fanRpmNormal
1.3.6.1.4.1.890.1.5.0.7 - overheat
1.3.6.1.4.1.890.1.5.0.3 - overheatOver
1.3.6.1.4.1.890.1.5.0.4 - reboot
1.3.6.1.4.1.890.1.5.0.1 - systemMaintenanceFailure
1.3.6.1.4.1.890.1.5.0.10 - systemShutdown
1.3.6.1.4.1.890.1.5.0.2 - thermalSensorFailure
1.3.6.1.4.1.890.1.5.0.12 - voltageNormal
1.3.6.1.4.1.890.1.5.0.9 - voltageOutOfRange
1.3.6.1.4.1.890.1.5.0.8