WESTERMO-WEOS-MIB
Westermo Network Technologies ABThis MIB module controls the SNMP functionality in the WeOS branch of the Westermo private MIB.
snmptranslate -m WESTERMO-WEOS-MIB -Tpsnmpwalk -v2c -c <community> -m WESTERMO-WEOS-MIB <host> 1.3.6.1.4.1.16177.2.1Imports
| ENTITY-MIB | entPhysicalName |
|---|---|
| ENTITY-SENSOR-MIB | entPhySensorPrecision, entPhySensorScale, entPhySensorType, entPhySensorValue |
| IF-MIB | InterfaceIndex |
| INET-ADDRESS-MIB | InetAddress, InetAddressType |
| Q-BRIDGE-MIB | VlanId |
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP |
| SNMPv2-SMI | Bits, Counter64, Integer32, IpAddress, MODULE-IDENTITY, MibIdentifier, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, iso |
| SNMPv2-TC | DisplayString, MacAddress, PhysAddress, RowStatus, TEXTUAL-CONVENTION, TruthValue |
| WESTERMO-OID-MIB | common |
OID tree
| Name | OID | Type | Access | Status |
|---|---|---|---|---|
| Iweos | 1.3.6.1.4.1.16177.2.1 | |||
identity This MIB module controls the SNMP functionality in the WeOS branch of the Westermo private MIB. | ||||
| Ncommand | 1.3.6.1.4.1.16177.2.1.1 | |||
| Sreboot | 1.3.6.1.4.1.16177.2.1.1.1 | INTEGER | RW | |
scalar · INTEGER · read-write · current Writing value '1' will reboot the unit. (The unit will boot up using the startup configuration) Reading the reboot object will return '0' (zero)
| ||||
| SfactoryReset | 1.3.6.1.4.1.16177.2.1.1.2 | INTEGER | RW | |
scalar · INTEGER · read-write · current Writing value '1' will reset unit configuration to factory default values and reboot. Reading the factoryReset object will return '0' (zero)
| ||||
| Nphy | 1.3.6.1.4.1.16177.2.1.2 | |||
| TlffTable | 1.3.6.1.4.1.16177.2.1.2.1 | NA | ||
table · not-accessible · current Table containing Westermo Link Fail Forward (LFF) settings and status applicable ports. Westermo LFF is used to indicate the state (up/down) of a remote link. The currently supported use case is when extending an Ethernet over an SHDSL link. LFF is used to inform the local end that the Ethernet link at the remote site is up or down. | ||||
| RlffEntry | 1.3.6.1.4.1.16177.2.1.2.1.1 | NA | ||
row · not-accessible · current For each local (SHDSL) port, there is a row in the lffTable containing LFF status and settings.
| ||||
| ClffPortIfIndex | 1.3.6.1.4.1.16177.2.1.2.1.1.1 | InterfaceIndex | RO | |
column · InterfaceIndex · read-only · current This index should map to the local (SHDSL) port's ifIndex in the ifTable. | ||||
| ClffPortIfName | 1.3.6.1.4.1.16177.2.1.2.1.1.2 | DisplayString | RO | |
column · DisplayString · read-only · current This name should map to the local (SHDSL) port's ifName in the ifXTable. | ||||
| ClffStatus | 1.3.6.1.4.1.16177.2.1.2.1.1.3 | INTEGER | RO | |
column · INTEGER · read-only · current The lffStatus shows the status of a (Ethernet) link at the remote end of a SHDSL link:
- 1 (disabled): LFF is configured 'disabled' on local (SHDSL) port.
- 2 (unknown): LFF enabled, but the state of remote (Ethernet)
is unknown. (perhaps because the intermediate
(SHDSL) link is down).
- 3 (remoteDown): LFF enabled, remote (Ethernet) port down
- 4 (remoteUp): LFF enabled, remote (Ethernet) port up.
| ||||
| Nsfp | 1.3.6.1.4.1.16177.2.1.2.2 | |||
| TsfpDdmPortTable | 1.3.6.1.4.1.16177.2.1.2.2.1 | NA | ||
table · not-accessible · current Table containing DDM diagnostics per DDM capable SFP. | ||||
| RsfpDdmPortEntry | 1.3.6.1.4.1.16177.2.1.2.2.1.1 | NA | ||
row · not-accessible · current This row in the sfpDdmPortTable containing per port SFP DDM diagnostics.
| ||||
| CsfpDdmPortIfIndex | 1.3.6.1.4.1.16177.2.1.2.2.1.1.1 | InterfaceIndex | AN | |
column · InterfaceIndex · accessible-for-notify · current This index maps to the port's ifIndex in the ifTable. | ||||
| CsfpDdmPortIfName | 1.3.6.1.4.1.16177.2.1.2.2.1.1.2 | DisplayString | RO | |
column · DisplayString · read-only · current The system name of the port. | ||||
| CsfpDdmPortVoltage | 1.3.6.1.4.1.16177.2.1.2.2.1.1.3 | Integer32 (0..6550) | RO | |
column · Integer32 (0..6550) · read-only · current The supply voltage of the SFP. The accuracy is better than +/-3 % and the total range of 0 - 6550 mV. The voltage is represented in mV. | ||||
| CsfpDdmPortTemperature | 1.3.6.1.4.1.16177.2.1.2.2.1.1.4 | Integer32 (-128..128) | RO | |
column · Integer32 (-128..128) · read-only · current Temperature of the SFP. The temperature accuracy is better than 3 degrees Celsius and the total range of -128 degrees C to +128 degrees C. | ||||
| CsfpDdmPortBiasCurrent | 1.3.6.1.4.1.16177.2.1.2.2.1.1.5 | Integer32 (0..131) | RO | |
column · Integer32 (0..131) · read-only · current The transmitt bias current. The accuracy is better than +/- 10 % and the total range of 0 - 131 mA. The current is represented in uA. | ||||
| CsfpDdmPortTxPower | 1.3.6.1.4.1.16177.2.1.2.2.1.1.6 | Integer32 (-4000..820) | RO | |
column · Integer32 (-4000..820) · read-only · current Transmitt power of the laser. The accuracy is better than +/-3dB and the total range of -40 to +8.2 dBm ~(0 - 6.5535 mW). The power is represented in steps of 0.01 dBm | ||||
| CsfpDdmPortRxPower | 1.3.6.1.4.1.16177.2.1.2.2.1.1.7 | Integer32 (-4000..820) | RO | |
column · Integer32 (-4000..820) · read-only · current Receiving power of the laser. The accuracy is better than +/-3dB and the total range of -40 to +8.2 dBm ~(0 - 6.5535 mW). The power is represented in steps of 0.01 dBm | ||||
| NphyStats | 1.3.6.1.4.1.16177.2.1.2.3 | |||
| SsummaryFCSErrors | 1.3.6.1.4.1.16177.2.1.2.3.1 | Integer32 | RO | |
scalar · Integer32 · read-only · current The summaryFCSErrors display the total of FCS errors for all ports on the unit | ||||
| TbwStatsTable | 1.3.6.1.4.1.16177.2.1.2.3.2 | NA | ||
table · not-accessible · current Table containing port bandwidth rates. | ||||
| RbwStatsEntry | 1.3.6.1.4.1.16177.2.1.2.3.2.1 | NA | ||
row · not-accessible · current For each local port, there is a row in the bwStatsTable containing port bandwidth rates.
| ||||
| CbwStatsIndex | 1.3.6.1.4.1.16177.2.1.2.3.2.1.1 | InterfaceIndex | RO | |
column · InterfaceIndex · read-only · current The value of this object uniquely identifies this bwStats entry. | ||||
| CbwStatsEnabled | 1.3.6.1.4.1.16177.2.1.2.3.2.1.2 | TruthValue | RO | |
column · TruthValue · read-only · current Bandwidth statistics enabled or disabled for this port. | ||||
| CbwStatsBitrateIn10s | 1.3.6.1.4.1.16177.2.1.2.3.2.1.3 | Counter64 | RO | |
column · Counter64 · read-only · current The current average input traffic for the last 10 seconds. This value is calculated via periodic sampling of the port counters And will be updated at least every 10 seconds. The unit is bits per second and this includes Ethernet header data (Ethernet preamble not included).
| ||||
| CbwStatsBitrateOut10s | 1.3.6.1.4.1.16177.2.1.2.3.2.1.4 | Counter64 | RO | |
column · Counter64 · read-only · current The current average output traffic for the last 10 seconds. This value is calculated via periodic sampling of the port counters And will be updated at least every 10 seconds. The unit is bits per second and this includes Ethernet header data (Ethernet preamble not included).
| ||||
| CbwStatsBitrateIn1m | 1.3.6.1.4.1.16177.2.1.2.3.2.1.5 | Counter64 | RO | |
column · Counter64 · read-only · current The current moving average input traffic for the last minute. This value is calculated and updated at least every 10 seconds. The unit is bits per second and this includes Ethernet header data (Ethernet preamble not included).
| ||||
| CbwStatsBitrateOut1m | 1.3.6.1.4.1.16177.2.1.2.3.2.1.6 | Counter64 | RO | |
column · Counter64 · read-only · current The current moving average output traffic for the last minute. This value is calculated and updated at least every 10 seconds. The unit is bits per second and this includes Ethernet header data (Ethernet preamble not included).
| ||||
| CbwStatsBitrateIn10m | 1.3.6.1.4.1.16177.2.1.2.3.2.1.7 | Counter64 | RO | |
column · Counter64 · read-only · current The current moving average input traffic for the last 10 minutes. This value is calculated and updated at least every 10 seconds. The unit is bits per second and this includes Ethernet header data (Ethernet preamble not included).
| ||||
| CbwStatsBitrateOut10m | 1.3.6.1.4.1.16177.2.1.2.3.2.1.8 | Counter64 | RO | |
column · Counter64 · read-only · current The current moving average output traffic for the last 10 minutes. This value is calculated and updated at least every 10 seconds. The unit is bits per second and this includes Ethernet header data (Ethernet preamble not included).
| ||||
| CbwStatsBitrateIn1h | 1.3.6.1.4.1.16177.2.1.2.3.2.1.9 | Counter64 | RO | |
column · Counter64 · read-only · current The current moving average input traffic for the last hour. This value is calculated and updated at least every 10 seconds. The unit is bits per second and this includes Ethernet header data (Ethernet preamble not included).
| ||||
| CbwStatsBitrateOut1h | 1.3.6.1.4.1.16177.2.1.2.3.2.1.10 | Counter64 | RO | |
column · Counter64 · read-only · current The current moving average output traffic for the last hour. This value is calculated and updated at least every 10 seconds. The unit is bits per second and this includes Ethernet header data (Ethernet preamble not included).
| ||||
| Nlink | 1.3.6.1.4.1.16177.2.1.3 | |||
| Nvlan | 1.3.6.1.4.1.16177.2.1.3.1 | |||
| Nl2Qos | 1.3.6.1.4.1.16177.2.1.3.2 | |||
| Tl2QosVlanTable | 1.3.6.1.4.1.16177.2.1.3.2.1 | NA | ||
table · not-accessible · current Table containing VLAN priority settings for existing VLANs. | ||||
| Rl2QosVlanEntry | 1.3.6.1.4.1.16177.2.1.3.2.1.1 | NA | ||
row · not-accessible · current The row in the l2QosVlanTable containing per VLAN priority settings.
| ||||
| Cl2QosVlanId | 1.3.6.1.4.1.16177.2.1.3.2.1.1.1 | VlanId | RO | |
column · VlanId · read-only · current This index should be mapped to the VLAN ID of Q-bridge MIB. | ||||
| CvlanPriorityEnabled | 1.3.6.1.4.1.16177.2.1.3.2.1.1.2 | TruthValue | RW | |
column · TruthValue · read-write · current Enable (true) or disable (false) VLAN priority for this VLAN. | ||||
| CvlanPriorityLevel | 1.3.6.1.4.1.16177.2.1.3.2.1.1.3 | Integer32 (0..7) | RW | |
column · Integer32 (0..7) · read-write · current The VLAN priority level for this VLAN. 0 is lowest and 7 is highest priority. | ||||
| Tl2QosPortTable | 1.3.6.1.4.1.16177.2.1.3.2.2 | NA | ||
table · not-accessible · current Table containing per port piority settings for LAN ports | ||||
| Rl2QosPortEntry | 1.3.6.1.4.1.16177.2.1.3.2.2.1 | NA | ||
row · not-accessible · current The row in the l2QosPortTable containing per port priority settings.
| ||||
| Cl2QosPortIfIndex | 1.3.6.1.4.1.16177.2.1.3.2.2.1.1 | InterfaceIndex | RO | |
column · InterfaceIndex · read-only · current This index should map to the port's ifIndex in the ifTable. | ||||
| Cl2QosPortIfName | 1.3.6.1.4.1.16177.2.1.3.2.2.1.2 | DisplayString | RO | |
column · DisplayString · read-only · current This name should map to the port's ifName in the ifXTable. | ||||
| Cl2QosPortPriorityMode | 1.3.6.1.4.1.16177.2.1.3.2.2.1.3 | INTEGER | RW | |
column · INTEGER · read-write · current The priority mode (tag, ip or port) to be used on this specific port. 1. (tag): Use the incoming packet's VLAN tag priority value to determine its priority. (Untagged packets will have their priority based on the configured port priority.) 2. (ip): Use the incoming packet's IP ToS/DSCP priority value to determine its priority. (Non-IP packets will have their priority based on the configured port priority.) 3. (port): Use the ingress port's configured priority to determine the packets priority.
| ||||
| Cl2QosPortPriorityLevel | 1.3.6.1.4.1.16177.2.1.3.2.2.1.4 | Integer32 (0..7) | RW | |
column · Integer32 (0..7) · read-write · current The port priority level for this port. 0 is lowest and 7 is highest priority. | ||||
| Nfrnt | 1.3.6.1.4.1.16177.2.1.3.3 | |||
| Nfrntv0 | 1.3.6.1.4.1.16177.2.1.3.3.1 | |||
| Tfrntv0Table | 1.3.6.1.4.1.16177.2.1.3.3.1.1 | NA | ||
table · not-accessible · current Table containing a list of FRNTv0 instances/rings. | ||||
| Rfrntv0Entry | 1.3.6.1.4.1.16177.2.1.3.3.1.1.1 | NA | ||
row · not-accessible · current The row in the frntv0Table containing settings and status information for a specific FRNTv0 instance/ring.
| ||||
| Cfrntv0InstanceId | 1.3.6.1.4.1.16177.2.1.3.3.1.1.1.1 | Integer32 (1..64) | AN | |
column · Integer32 (1..64) · accessible-for-notify · current The instance id of this FRNTv0 Ring (only of local significance to this unit). | ||||
| Cfrntv0FocalPointEnabled | 1.3.6.1.4.1.16177.2.1.3.3.1.1.1.2 | TruthValue | RC | |
column · TruthValue · read-create · current True(1) if this unit is configured as focal point for this FRNTv0 instance. False(2) if this unit is configured as member switch for this FRNTv0 instance. | ||||
| Cfrntv0Port1 | 1.3.6.1.4.1.16177.2.1.3.3.1.1.1.3 | DisplayString | RC | |
column · DisplayString · read-create · current Name of FRNT port M in the FRNT port pair. In case the unit is configured as focal point and the ring is fully connected, it is port M that is put in BLOCKING. | ||||
| Cfrntv0Port2 | 1.3.6.1.4.1.16177.2.1.3.3.1.1.1.4 | DisplayString | RC | |
column · DisplayString · read-create · current Name of FRNT port N in the FRNT port pair. In case of an edge in a FRNT bus rather than a node in a FRNT ring then port N shall be set to 'None' and it will be read as 'None'. In case the unit is configured as focal point and the ring is fully connected, it is port M that is put in BLOCKING. | ||||
| Cfrntv0Port1State | 1.3.6.1.4.1.16177.2.1.3.3.1.1.1.5 | INTEGER | RO | |
column · INTEGER · read-only · current Provides information about the status of FRNT port M. See frntv0RingStatus for more details.
| ||||
| Cfrntv0Port2State | 1.3.6.1.4.1.16177.2.1.3.3.1.1.1.6 | INTEGER | RO | |
column · INTEGER · read-only · current Provides information about the status of FRNT port N. See frntv0RingStatus for more details.
| ||||
| Cfrntv0RingStatus | 1.3.6.1.4.1.16177.2.1.3.3.1.1.1.7 | INTEGER | RO | |
column · INTEGER · read-only · current Read ring status information. The answer is to be interpreted differently when asking a focal point or a member switch. Focal point (status of the whole FRNT topology): 1. ring mode: A focal point reports 'ring(1)' when the FRNT topology is intact. On a focal point this indicates OK. 2. bus mode: A focal point reports 'bus(2)' when it has detected an ERROR in the FRNT topology, i.e., the topology is broken. It can either be an error on any of its local FRNT ports (M or N), or elsewhere in the FRNT topology. Member switch (status of the member's local FRNT ports): 1. ring mode: A member switch reports 'ring(1)' when one or both of its FRNT ports are down or in blocking state. On a member switch this indicates an ERROR. 2. bus mode: A member switch reports 'bus(2)' when both its FRNT ports are in forwarding state. On a member switch this is an indication of OK, but it only has significance for this member switch, not the whole FRNT topology.
| ||||
| Cfrntv0RowStatus | 1.3.6.1.4.1.16177.2.1.3.3.1.1.1.8 | RowStatus | RC | |
column · RowStatus · read-create · current This object indicates the status of this table entry. | ||||
| Cfrntv0TopologyChangeCount | 1.3.6.1.4.1.16177.2.1.3.3.1.1.1.9 | Integer32 | RO | |
column · Integer32 · read-only · current This object indicates the number of transitions between bus/ring mode since FRNT was enabled. | ||||
| Cfrntv0TopologyTimeSinceLastChange | 1.3.6.1.4.1.16177.2.1.3.3.1.1.1.10 | TimeTicks | RO | |
column · TimeTicks · read-only · current This object indicates the time that have passed since the last change of ring status. | ||||
| Cfrntv0PortsSwapped | 1.3.6.1.4.1.16177.2.1.3.3.1.1.1.11 | TruthValue | RO | |
column · TruthValue · read-only · current FRNT can detect if the FRNT ports have been swapped. For example if port1 is connected to port1 on another FRNT unit. True(1) if the ports are swapped. False(2) if the ports are not swapped. | ||||
| NigmpSnooping | 1.3.6.1.4.1.16177.2.1.3.4 | |||
| SigmpSnoopingQuerierMode | 1.3.6.1.4.1.16177.2.1.3.4.1 | INTEGER | RW | |
scalar · INTEGER · read-write · current The querierMode object controls the querier mode an IGMP snooping switch will operate in on IGMP Snooping enabled VLANs. If the switch does not have an IP address on a certain VLAN, the switch will act in proxy querier mode irrespective of the querierMode setting. 1. Autonegotiate querier. The switch will become querier on a VLAN unless it hears IGMP queries on that VLAN from device with lower IP address. 2. Force querier role. The switch will act as querier on every VLAN where IGMP snooping is enabled. 3. Operate in proxy querier mode.
| ||||
| SigmpSnoopingQuerierInterval | 1.3.6.1.4.1.16177.2.1.3.4.2 | Integer32 | RW | |
scalar · Integer32 · read-write · current The IGMP Querier Interval (seconds). This interval will be used on all interfaces where this unit acts as IGMP Querier, unless multicast routing protocol specific or interface specific querier setting exist. Currently, the following interval values are valid: 12, 30, 70 and 150 (seconds). | ||||
| SstaticMulticastRouterPorts | 1.3.6.1.4.1.16177.2.1.3.4.3 | DisplayString | RW | |
scalar · DisplayString · read-write · current This is a comma-separated list of (LAN)port names, which specifies statically configured 'multicast router ports'. All layer-2 multicast traffic (known and unknown) should be forwarded onto multicast router ports. | ||||
| ScurrentMulticastRouterPorts | 1.3.6.1.4.1.16177.2.1.3.4.4 | DisplayString | RO | |
scalar · DisplayString · read-only · current This is a comma-separated list of portnames, which lists all ports operating as multicast router ports - both dynamically discovered (e.g., by reception of IGMP Queries) or statically configured multicast router ports. All (layer-2) multicast traffic (known and unknown) should be forwarded onto multicast router ports. | ||||
| TigmpSnoopingVlanTable | 1.3.6.1.4.1.16177.2.1.3.4.5 | NA | ||
table · not-accessible · current A list of configuration entries for VLAN specific IGMP Snooping objects. | ||||
| RigmpSnoopingVlanEntry | 1.3.6.1.4.1.16177.2.1.3.4.5.1 | NA | ||
row · not-accessible · current An IGMP Snooping VLAN entry contains IGMP Snooping objects relevant for IGMP Snooping management per VLAN.
| ||||
| CigmpSnoopingVlanId | 1.3.6.1.4.1.16177.2.1.3.4.5.1.1 | VlanId | RO | |
column · VlanId · read-only · current This index should match corresponding VLAN ID of Q-bridge MIB. | ||||
| CigmpSnoopingEnabled | 1.3.6.1.4.1.16177.2.1.3.4.5.1.2 | TruthValue | RW | |
column · TruthValue · read-write · current IGMP Snooping enabled or disabled on this particular VLAN. | ||||
| Nrico | 1.3.6.1.4.1.16177.2.1.3.5 | |||
| TriCoStatusTable | 1.3.6.1.4.1.16177.2.1.3.5.1 | NA | ||
table · not-accessible · current Table containing status for a list of RiCo and/or Dual Homing instances present on this unit. | ||||
| RriCoStatusEntry | 1.3.6.1.4.1.16177.2.1.3.5.1.1 | NA | ||
row · not-accessible · current Row in the riCoStatusTable that is containing settings and status information for a specific RiCo/Dual-Homing instance. | ||||
| CriCoStatusRingIdx | 1.3.6.1.4.1.16177.2.1.3.5.1.1.1 | Integer32 (0..255) | AN | |
column · Integer32 (0..255) · accessible-for-notify · current The ring instance ID of this RiCo/Dual-Homing instance (only of local significance to this unit). - For RiCo instances, the ring ID corresponds to the associated FRNT ring ID. - For Dual Homing instances, the ring ID is always '0'. | ||||
| CriCoStatusCouplingIdx | 1.3.6.1.4.1.16177.2.1.3.5.1.1.2 | Integer32 (1..8) | AN | |
column · Integer32 (1..8) · accessible-for-notify · current The ID of this RiCo/Dual-Homing instance. (only of local significance to this unit). Unique per ring instance (riCoStatusRingIdx). | ||||
| CriCoStatusNodeId | 1.3.6.1.4.1.16177.2.1.3.5.1.1.3 | MacAddress | AN | |
column · MacAddress · accessible-for-notify · current The unique ID of this RiCo node. A MAC address (typically the base MAC address) of this unit. | ||||
| CriCoStatusHelloInterval | 1.3.6.1.4.1.16177.2.1.3.5.1.1.4 | Integer32 | RO | |
column · Integer32 · read-only · current Configured RiCo Ring Hello interval in milliseconds. Not applicable for Dual Homing instances (value '0') | ||||
| CriCoStatusHelloEffective | 1.3.6.1.4.1.16177.2.1.3.5.1.1.5 | Integer32 | RO | |
column · Integer32 · read-only · current Effective RiCo Ring Hello interval in milliseconds. Shows negotiated Hello interval. Not applicable for Dual Homing instances (value '0'). | ||||
| TriCoStatusUplinkTable | 1.3.6.1.4.1.16177.2.1.3.5.2 | NA | ||
table · not-accessible · current Table containing status of RiCo and Dual-Homing uplinks per link | ||||
| RriCoStatusUplinkEntry | 1.3.6.1.4.1.16177.2.1.3.5.2.1 | NA | ||
row · not-accessible · current The row in the riCoStatusUplinkTable containing status information for a specific RiCo or Dual-Homing uplink. For RiCo, status for all local uplinks, and for the best uplink of each RiCo peer is listed. For dual-homing, status for all local uplinks is listed. | ||||
| CriCoStatusUplinkRingIdx | 1.3.6.1.4.1.16177.2.1.3.5.2.1.1 | Integer32 (0..255) | AN | |
column · Integer32 (0..255) · accessible-for-notify · current The ring instance ID of this RiCo/Dual-Homing instance
(only of local significance to this unit).
- For RiCo instances, the ring ID corresponds to the
associated FRNT ring ID.
- For Dual Homing instances, the ring ID is always '0'. | ||||
| CriCoStatusUplinkCouplingIdx | 1.3.6.1.4.1.16177.2.1.3.5.2.1.2 | Integer32 (1..8) | AN | |
column · Integer32 (1..8) · accessible-for-notify · current The instance id of this riCo Uplink | ||||
| CriCoStatusUplinkNodeId | 1.3.6.1.4.1.16177.2.1.3.5.2.1.3 | MacAddress | AN | |
column · MacAddress · accessible-for-notify · current The unique ID of the node, i.e., the MAC address of the node. For RiCo, this can be the (base) MAC of the local unit, or the MAC identifying a peer RiCo node. For Dual-Homing, this is the (base) MAC of the local unit. | ||||
| CriCoStatusUplinkIfIndex | 1.3.6.1.4.1.16177.2.1.3.5.2.1.4 | InterfaceIndex | RO | |
column · InterfaceIndex · read-only · current The interface index of the uplink port. - For local uplinks, this index corresponds to the port's index in the ifTable (IF-MIB). - For non-local uplinks, the value is not valid (value '0'). | ||||
| CriCoStatusUplinkStatus | 1.3.6.1.4.1.16177.2.1.3.5.2.1.5 | INTEGER | RO | |
column · INTEGER · read-only · current Uplink active (1), backup (2) or down (3).
| ||||
| CriCoStatusUplinkIfName | 1.3.6.1.4.1.16177.2.1.3.5.2.1.6 | DisplayString | RO | |
column · DisplayString · read-only · current The name of the interface used for this uplink. | ||||
| CriCoStatusUplinkPrio | 1.3.6.1.4.1.16177.2.1.3.5.2.1.7 | Integer32 | RO | |
column · Integer32 · read-only · current Effective priority of this uplink. Based on configured priority and 'adjust' value (sticky uplink). | ||||
| CriCoStatusUplinkPathCost | 1.3.6.1.4.1.16177.2.1.3.5.2.1.8 | Integer32 | RO | |
column · Integer32 · read-only · current Current path cost for this uplink. | ||||
| CriCoStatusUplinkHelloInterval | 1.3.6.1.4.1.16177.2.1.3.5.2.1.9 | Integer32 | RO | |
column · Integer32 · read-only · current Configured Ring Hello Interval for the RiCo node of this uplink. Not valid for Dual-Homing, value '0') | ||||
| CriCoStatusUplinkHelloIntervalEffective | 1.3.6.1.4.1.16177.2.1.3.5.2.1.10 | Integer32 | RO | |
column · Integer32 · read-only · current Effective Ring Hello Interval for the RiCo node of this uplink. Not valid for Dual-Homing, value '0') | ||||
| CriCoStatusUplinkChangedCounter | 1.3.6.1.4.1.16177.2.1.3.5.2.1.11 | Integer32 | RO | |
column · Integer32 · read-only · current Number of times this uplink changed its state | ||||
| CriCoStatusUplinkSynchronized | 1.3.6.1.4.1.16177.2.1.3.5.2.1.12 | INTEGER | RO | |
column · INTEGER · read-only · current Synchronization status for this uplink:
- synchronized(1): Synchronize enabled and ok
- notSynchronized(2): Synchronize enabled and fails
- notApplicable(3): Non-local RiCo uplink, or Dual-Homing
uplink where Synchronize is disabled
| ||||
| CriCoStatusUplinkPreferred | 1.3.6.1.4.1.16177.2.1.3.5.2.1.13 | INTEGER | RO | |
column · INTEGER · read-only · current Preferred uplink status.
Only valid for Dual-Homing uplinks whit synchronization enabled.
- preferred(1): Dual-Homing uplink has status 'Preferred'
- notPreferred(2): Dual-Homing uplink has status 'Not Preferred'
- notApplicable(3): Uplink is either
- a Dual-Homing uplink with synchronization disabled, or
- a RiCo uplink (local or non-local)
| ||||
| CriCoStatusUplinkLocal | 1.3.6.1.4.1.16177.2.1.3.5.2.1.14 | TruthValue | RO | |
column · TruthValue · read-only · current Local(true) or global(false) instance | ||||
| TriCoCfgTable | 1.3.6.1.4.1.16177.2.1.3.5.3 | NA | ||
table · not-accessible · current Table containing a list of RiCo couplings. | ||||
| RriCoCfgEntry | 1.3.6.1.4.1.16177.2.1.3.5.3.1 | NA | ||
row · not-accessible · current The row in the riCoTable containing settings for a specific RiCo or Dual-Homing instance. | ||||
| CriCoCfgRingIdx | 1.3.6.1.4.1.16177.2.1.3.5.3.1.1 | Integer32 (0..255) | RC | |
column · Integer32 (0..255) · read-create · current The ring instance ID of this RiCo/Dual-Homing instance
(only of local significance to this unit).
- For RiCo instances, the ring ID corresponds to the
associated FRNT ring ID.
- For Dual Homing instances, the ring ID is always '0'. | ||||
| CriCoCfgCouplingIdx | 1.3.6.1.4.1.16177.2.1.3.5.3.1.2 | Integer32 (1..8) | RC | |
column · Integer32 (1..8) · read-create · current The ID of this RiCo/Dual-Homing instance. (only of local significance to this unit). Unique per ring instance (riCoCfgRingIdx). | ||||
| CriCoCfgEnabled | 1.3.6.1.4.1.16177.2.1.3.5.3.1.3 | TruthValue | RC | |
column · TruthValue · read-create · current Enable or disable the RiCo instance True (1) or False (2) | ||||
| CriCoCfgHelloInterval | 1.3.6.1.4.1.16177.2.1.3.5.3.1.4 | Integer32 | RC | |
column · Integer32 · read-create · current Configured RiCo Ring Hello interval in milliseconds. - Default: 100 milliseconds - Configurable in range: 50-1000 milliseconds - Not applicable for Dual Homing instances (value '0') | ||||
| CriCoCfgSynchronize | 1.3.6.1.4.1.16177.2.1.3.5.3.1.5 | TruthValue | RC | |
column · TruthValue · read-create · current Enable/disable Uplink synchronization. 'True' to enable, and 'False' to disable synchronization. Note: Only configurable for Dual-Homing Uplinks. For RiCo Uplinks, synchronization is always enabled. | ||||
| CriCoCfgRowStatus | 1.3.6.1.4.1.16177.2.1.3.5.3.1.6 | RowStatus | RC | |
column · RowStatus · read-create · current This object indicates the status of this table entry. This object can also be used to create or delete instances. At most 1 RiCo instance and at most 8 Dual-Homing instances can be created. | ||||
| TriCoCfgUplinkTable | 1.3.6.1.4.1.16177.2.1.3.5.4 | NA | ||
table · not-accessible · current Table containing RiCo and Dual-Homing uplinks and corresponding settings per link. | ||||
| RriCoCfgUplinkEntry | 1.3.6.1.4.1.16177.2.1.3.5.4.1 | NA | ||
row · not-accessible · current The row in the riCoLinkTable containing settings and status information for a specific RiCo or Dual-Homing Uplink. | ||||
| CriCoCfgUplinkRingIdx | 1.3.6.1.4.1.16177.2.1.3.5.4.1.1 | Integer32 (0..255) | RC | |
column · Integer32 (0..255) · read-create · current The ring instance ID of this RiCo/Dual-Homing instance (only of local significance to this unit). - For RiCo instances, the ring ID corresponds to the associated FRNT ring ID. - For Dual Homing instances, the ring ID is always '0'. | ||||
| CriCoCfgUplinkCouplingIdx | 1.3.6.1.4.1.16177.2.1.3.5.4.1.2 | Integer32 (1..8) | RC | |
column · Integer32 (1..8) · read-create · current The ID of this RiCo/Dual-Homing instance. (only of local significance to this unit). Unique per ring instance (riCoStatusRingIdx). | ||||
| CriCoCfgUplinkIfIndex | 1.3.6.1.4.1.16177.2.1.3.5.4.1.3 | InterfaceIndex | RC | |
column · InterfaceIndex · read-create · current The interface index of the uplink port. For local uplinks, this index corresponds to the port's index in the ifTable (IF-MIB). | ||||
| CriCoCfgUplinkPrio | 1.3.6.1.4.1.16177.2.1.3.5.4.1.4 | Integer32 | RC | |
column · Integer32 · read-create · current Configure priority for this uplink (128 as default). A lower value increases the chance to be elected as active uplink. | ||||
| CriCoCfgUplinkAdjust | 1.3.6.1.4.1.16177.2.1.3.5.4.1.5 | Integer32 | RC | |
column · Integer32 · read-create · current Configure adjust value for this uplink (sticky uplink). The effictive priority is reduced by the adjust value if the link becomes elected as active uplink. Default '0'. | ||||
| CriCoCfgUplinkEchoTime | 1.3.6.1.4.1.16177.2.1.3.5.4.1.6 | Integer32 | RC | |
column · Integer32 · read-create · current Uplink echo interval to be set for this uplink in milliseconds. Default: 200 ms Range: 20-1000 ms | ||||
| CriCoCfgUplinkPathCost | 1.3.6.1.4.1.16177.2.1.3.5.4.1.7 | Integer32 | RC | |
column · Integer32 · read-create · current Path-cost to be set for this uplink. '0' means 'Auto', which lets path cost depend on speed and duplex of the uplink. | ||||
| CriCoCfgUplinkRowStatus | 1.3.6.1.4.1.16177.2.1.3.5.4.1.8 | RowStatus | RC | |
column · RowStatus · read-create · current This object indicates the status of this table entry. | ||||
| NlldpCtlv | 1.3.6.1.4.1.16177.2.1.3.6 | |||
| TlldpCtlvTable | 1.3.6.1.4.1.16177.2.1.3.6.1 | NA | ||
table · not-accessible · current The LLDP custom TLV (Type 127) configuration table | ||||
| RlldpCtlvEntry | 1.3.6.1.4.1.16177.2.1.3.6.1.1 | NA | ||
| ClldpCtlvIdx | 1.3.6.1.4.1.16177.2.1.3.6.1.1.1 | INTEGER (1..60) | RO | |
column · INTEGER (1..60) · read-only · current Index of this custom TLV. Only of local significance. | ||||
| ClldpCtlvOui | 1.3.6.1.4.1.16177.2.1.3.6.1.1.2 | OCTET STRING | RC | |
column · OCTET STRING · read-create · current Organizationally unique identifier (OUI), 3 hex-encoded bytes. Required. | ||||
| ClldpCtlvSubType | 1.3.6.1.4.1.16177.2.1.3.6.1.1.3 | INTEGER (0..255) | RC | |
column · INTEGER (0..255) · read-create · current Organizationally defined subtype, one byte. Default: 0 | ||||
| ClldpCtlvInfo | 1.3.6.1.4.1.16177.2.1.3.6.1.1.4 | OCTET STRING | RC | |
column · OCTET STRING · read-create · current Information/value part of custom TLV. 0-507 octets encoded as hex. Default: Empty | ||||
| ClldpCtlvRowStatus | 1.3.6.1.4.1.16177.2.1.3.6.1.1.5 | RowStatus | RC | |
column · RowStatus · read-create · current This object indicates the status of this table entry. Used to create or delete a custom TLV entry. | ||||
| TlldpCtlvPortTable | 1.3.6.1.4.1.16177.2.1.3.6.2 | NA | ||
table · not-accessible · current Table specifying which custom TLV(s) to transmit per port. Each row in the table maps a custom TLV to a port. Each custom TLV in the lldpCtlvTable can be mapped to one or more ports. | ||||
| RlldpCtlvPortEntry | 1.3.6.1.4.1.16177.2.1.3.6.2.1 | NA | ||
row · not-accessible · current Each entry maps a custom TLV to a port.
| ||||
| ClldpCtlvPortIdx | 1.3.6.1.4.1.16177.2.1.3.6.2.1.1 | INTEGER (1..255) | NA | |
column · INTEGER (1..255) · not-accessible · current The logical number of the port. This is the same number as the dot1dBasePort (dot1dBasePortTable of BRIDGE-MIB) for this port. | ||||
| ClldpCtlvPortCtlvIdx | 1.3.6.1.4.1.16177.2.1.3.6.2.1.2 | INTEGER | NA | |
column · INTEGER · not-accessible · current Custom TLV index (lldpCtlvTable) | ||||
| ClldpCtlvPortRowStatus | 1.3.6.1.4.1.16177.2.1.3.6.2.1.3 | RowStatus | RC | |
column · RowStatus · read-create · current This object indicates the status of this table entry. Used to create or delete a 'custom TLV to port' mapping. | ||||
| TlldpRemCtlvTable | 1.3.6.1.4.1.16177.2.1.3.6.3 | NA | ||
table · not-accessible · current Table listing all custom TLV(s) received. Each entry represents a custom TLV received on a specific port from individual neighbours. Entries are removed when the TTL of the LLDP message expires, and will be removed/replaced when a new LLDP message from the same neighbour is received. | ||||
| RlldpRemCtlvEntry | 1.3.6.1.4.1.16177.2.1.3.6.3.1 | NA | ||
row · not-accessible · current Custom TLV received on a port. | ||||
| ClldpRemCtlvLocalPort | 1.3.6.1.4.1.16177.2.1.3.6.3.1.1 | INTEGER (1..255) | RO | |
column · INTEGER (1..255) · read-only · current The logical number of the local port receiving this custom TLV. This is the same number as the dot1dBasePort (dot1dBasePortTable of BRIDGE-MIB) for this port. | ||||
| ClldpRemCtlvMacAddress | 1.3.6.1.4.1.16177.2.1.3.6.3.1.2 | MacAddress | RO | |
column · MacAddress · read-only · current The MAC address of the neighbour node sending this custom TLV. | ||||
| ClldpRemCtlvOui | 1.3.6.1.4.1.16177.2.1.3.6.3.1.3 | OCTET STRING (SIZE (3)) | RO | |
column · OCTET STRING (SIZE (3)) · read-only · current Organizationally unique identifier (OUI), 3 hex-encoded bytes. | ||||
| ClldpRemCtlvSubType | 1.3.6.1.4.1.16177.2.1.3.6.3.1.4 | INTEGER (0..255) | RO | |
column · INTEGER (0..255) · read-only · current Organizationally defined subtype, one byte. | ||||
| ClldpRemCtlvInfo | 1.3.6.1.4.1.16177.2.1.3.6.3.1.5 | OCTET STRING | RO | |
column · OCTET STRING · read-only · current Information/value part of custom TLV. 0-507 octets encoded as hex. | ||||
| Nnet | 1.3.6.1.4.1.16177.2.1.4 | |||
| Niface | 1.3.6.1.4.1.16177.2.1.4.1 | |||
| NifaceCommon | 1.3.6.1.4.1.16177.2.1.4.1.1 | |||
| NifaceInet4 | 1.3.6.1.4.1.16177.2.1.4.1.2 | |||
| Sinet4StaticDefaultGatewayAddress | 1.3.6.1.4.1.16177.2.1.4.1.2.1 | IpAddress | RW | |
scalar · IpAddress · read-write · current IP Address of statically configured default gateway. Setting the address to 0.0.0.0 means that there is 'no static default gateway' configured. | ||||
| Tinet4BaseIfaceTable | 1.3.6.1.4.1.16177.2.1.4.1.2.2 | NA | ||
table · not-accessible · current Table containing base IPv4 settings per interface | ||||
| Rinet4BaseIfaceEntry | 1.3.6.1.4.1.16177.2.1.4.1.2.2.1 | NA | ||
row · not-accessible · current Entry in ipv4Interface table. Each row holds IPv4 settings specific to this interface.
| ||||
| Cinet4BaseIfIndex | 1.3.6.1.4.1.16177.2.1.4.1.2.2.1.1 | InterfaceIndex | RO | |
column · InterfaceIndex · read-only · current Uniquely identifies an interface; same interface as identied by the same value of ifIndex in the interfaces group. | ||||
| Cinet4BaseIfName | 1.3.6.1.4.1.16177.2.1.4.1.2.2.1.2 | DisplayString | RO | |
column · DisplayString · read-only · current The name matches the corresponding ifName in the ifXTable. | ||||
| Cinet4BaseAddressMode | 1.3.6.1.4.1.16177.2.1.4.1.2.2.1.3 | INTEGER | RW | |
column · INTEGER · read-write · current The IPv4 address assignment mode.
| ||||
| Tinet4StaticTable | 1.3.6.1.4.1.16177.2.1.4.1.2.3 | NA | ||
table · not-accessible · current Table containing settings for static IPv4 interfaces | ||||
| Rinet4StaticEntry | 1.3.6.1.4.1.16177.2.1.4.1.2.3.1 | NA | ||
row · not-accessible · current Entry in ipv4Interface table. Each row holds IPv4 settings specific to this interface.
| ||||
| Cinet4StatIfIndex | 1.3.6.1.4.1.16177.2.1.4.1.2.3.1.1 | InterfaceIndex | RO | |
column · InterfaceIndex · read-only · current Uniquely identifies an interface; same interface as identied by the same value of ifIndex in the interfaces group. | ||||
| Cinet4StatIfName | 1.3.6.1.4.1.16177.2.1.4.1.2.3.1.2 | DisplayString | RO | |
column · DisplayString · read-only · current The name matches the corresponding ifName in the ifXTable. | ||||
| Cinet4StatAddress | 1.3.6.1.4.1.16177.2.1.4.1.2.3.1.3 | IpAddress | RW | |
column · IpAddress · read-write · current Statically configured IPv4 address for this interface. Address 0.0.0.0 means that the interface is disabled. | ||||
| Cinet4StatNetmask | 1.3.6.1.4.1.16177.2.1.4.1.2.3.1.4 | IpAddress | RW | |
column · IpAddress · read-write · current Netmask of statically assigned IP address. | ||||
| Tinet4DhcpTable | 1.3.6.1.4.1.16177.2.1.4.1.2.4 | NA | ||
table · not-accessible · current Table containing settings for IPv4 interfaces using DHCP for address assignment | ||||
| Rinet4DhcpEntry | 1.3.6.1.4.1.16177.2.1.4.1.2.4.1 | NA | ||
row · not-accessible · current Entry in inet4Dhcp table. Each row holds DHCP settings specific to this interface.
| ||||
| Cinet4DhcpIfIndex | 1.3.6.1.4.1.16177.2.1.4.1.2.4.1.1 | InterfaceIndex | RO | |
column · InterfaceIndex · read-only · current Uniquely identifies an interface; same interface as identied by the same value of ifIndex in the interfaces group. | ||||
| Cinet4DhcpIfName | 1.3.6.1.4.1.16177.2.1.4.1.2.4.1.2 | DisplayString | RO | |
column · DisplayString · read-only · current The name matches the corresponding ifName in the ifXTable. | ||||
| Cinet4DhcpClientId | 1.3.6.1.4.1.16177.2.1.4.1.2.4.1.3 | DisplayString | RO | |
column · DisplayString · read-only · current Client ID passed by DHCP client to DHCP server. | ||||
| NaddressConflict | 1.3.6.1.4.1.16177.2.1.4.1.4 | |||
| SaddressConflictExists | 1.3.6.1.4.1.16177.2.1.4.1.4.1 | TruthValue | RO | |
scalar · TruthValue · read-only · current True if there are any conflicts detected, False if there are no more conflicts detected. | ||||
| TaddressConflictTable | 1.3.6.1.4.1.16177.2.1.4.1.4.2 | NA | ||
table · not-accessible · current A list containing all IP and MAC address conflicts currently on the this device | ||||
| RaddressConflictEntry | 1.3.6.1.4.1.16177.2.1.4.1.4.2.1 | NA | ||
| CaddressConflictIndex | 1.3.6.1.4.1.16177.2.1.4.1.4.2.1.1 | Integer32 (0..256) | RO | |
column · Integer32 (0..256) · read-only · current A unique value for each conflict. | ||||
| CaddressConflictIfIndex | 1.3.6.1.4.1.16177.2.1.4.1.4.2.1.2 | InterfaceIndex | RO | |
column · InterfaceIndex · read-only · current Index of the interface on this device. | ||||
| CaddressConflictIfName | 1.3.6.1.4.1.16177.2.1.4.1.4.2.1.3 | DisplayString | RO | |
column · DisplayString · read-only · current Name of the interface on this device. | ||||
| CaddressConflictType | 1.3.6.1.4.1.16177.2.1.4.1.4.2.1.4 | INTEGER | RO | |
column · INTEGER · read-only · current Type of conflict: 1 : IP, 2 : MAC, 3 : IP & MAC
| ||||
| CaddressConflictMacAddress | 1.3.6.1.4.1.16177.2.1.4.1.4.2.1.5 | PhysAddress | RO | |
column · PhysAddress · read-only · current The MAC address of the conflicting peer. | ||||
| CaddressConflictIPv4Address | 1.3.6.1.4.1.16177.2.1.4.1.4.2.1.6 | IpAddress | RO | |
column · IpAddress · read-only · current The IPv4 address of the conflicting peer. | ||||
| CaddressConflictTime | 1.3.6.1.4.1.16177.2.1.4.1.4.2.1.7 | TimeTicks | RO | |
column · TimeTicks · read-only · current Time (in seconds) elapsed since conflict was last detected. | ||||
| Nttdp | 1.3.6.1.4.1.16177.2.1.4.2 | |||
| SetbnInhibitionEnabled | 1.3.6.1.4.1.16177.2.1.4.2.1 | TruthValue | RW | |
scalar · TruthValue · read-write · current ETBN inhibition enabled or disabled. | ||||
| Nsystem | 1.3.6.1.4.1.16177.2.1.5 | |||
| Nservices | 1.3.6.1.4.1.16177.2.1.5.1 | |||
| Nsnmp | 1.3.6.1.4.1.16177.2.1.5.1.1 | |||
| StrapCommunity | 1.3.6.1.4.1.16177.2.1.5.1.1.1 | DisplayString | RW | |
scalar · DisplayString · read-write · current The trap community name which traps destined to defined traphost(s) are sent with. | ||||
| TtrapHostTable | 1.3.6.1.4.1.16177.2.1.5.1.1.2 | NA | ||
table · not-accessible · current A list of SNMP trap host. | ||||
| RtrapHostEntry | 1.3.6.1.4.1.16177.2.1.5.1.1.2.1 | NA | ||
row · not-accessible · current An entry containing information about a specific SNMP trap host.
| ||||
| CtrapHostId | 1.3.6.1.4.1.16177.2.1.5.1.1.2.1.1 | Integer32 (1..64) | RO | |
column · Integer32 (1..64) · read-only · current The id of this SNMP Trap Host (only of local significance to this unit). | ||||
| CtrapHostAddressType | 1.3.6.1.4.1.16177.2.1.5.1.1.2.1.2 | InetAddressType | RO | |
column · InetAddressType · read-only · current The type of Internet address by which the trap host is reachable. | ||||
| CtrapHostAddress | 1.3.6.1.4.1.16177.2.1.5.1.1.2.1.3 | DisplayString | RC | |
column · DisplayString · read-create · current The IP address or Domain name for the trap host. | ||||
| CtrapHostRowStatus | 1.3.6.1.4.1.16177.2.1.5.1.1.2.1.4 | RowStatus | RC | |
column · RowStatus · read-create · current This object indicates the status of this table entry. | ||||
| SroCommunity | 1.3.6.1.4.1.16177.2.1.5.1.1.3 | DisplayString | RW | |
scalar · DisplayString · read-write · current The read-only community name used to by SNMPv1/v2 to read
SNMP MIB parameters. The string 'Disabled' have a special
meaning and cannot be used as roCommunity string.
Reading:
String 'Disabled' - The read-only community is disabled
Otherwise the received string shows the current read-only community.
Writing:
String 'Disabled' - Disable the read-write community
Otherwise the written string becomes the new read-only community. | ||||
| SrwCommunity | 1.3.6.1.4.1.16177.2.1.5.1.1.4 | DisplayString | RW | |
scalar · DisplayString · read-write · current Provides a mechanism to change or enable/disable the
read-write community name used to by SNMPv1/v2 to read and set
SNMP MIB parameters, however, for security reasons the configured
value is never displayed. The strings 'Enabled' and 'Disabled'
have special meanings and cannot be used as rwCommunity string.
Reading:
String 'Enabled' - A read-write community is configured
String 'Disabled' - The read-write community is disabled.
Writing:
String 'Disabled' - Disable the read-write community
Otherwise the written string becomes the new read-write
community (this implies that the read-write community is
enabled if it was earlier disabled.
Note that enabling the read-write community via SNMP is only
possible from SNMPv3. | ||||
| Nweb | 1.3.6.1.4.1.16177.2.1.5.1.2 | |||
| SwebEnabled | 1.3.6.1.4.1.16177.2.1.5.1.2.1 | TruthValue | RW | |
scalar · TruthValue · read-write · current Web daemon enabled or disabled. | ||||
| Nipconfig | 1.3.6.1.4.1.16177.2.1.5.1.3 | |||
| SipconfigEnabled | 1.3.6.1.4.1.16177.2.1.5.1.3.1 | TruthValue | RW | |
scalar · TruthValue · read-write · current IPConfig daemon enabled or disabled. | ||||
| Nssh | 1.3.6.1.4.1.16177.2.1.5.1.4 | |||
| SsshEnabled | 1.3.6.1.4.1.16177.2.1.5.1.4.1 | TruthValue | RW | |
scalar · TruthValue · read-write · current SSH daemon enabled or disabled. | ||||
| Nlldp | 1.3.6.1.4.1.16177.2.1.5.1.5 | |||
| SlldpEnabled | 1.3.6.1.4.1.16177.2.1.5.1.5.1 | TruthValue | RW | |
scalar · TruthValue · read-write · current LLDP service enabled or disabled.
- True: Enabling LLDP will enable the LLDP service with default settings.
- False: Disabling LLDP will fully disable the LLDP service, remove any
existing configuration, and disableaccess to any other LLDP OID
in private MIB andin LLDP MIB. | ||||
| SlldpActivated | 1.3.6.1.4.1.16177.2.1.5.1.5.2 | TruthValue | RW | |
scalar · TruthValue · read-write · current Activate/deactivate LLDP configuration.
- True: LLDP daemon enabled with existing configuration
- False: LLDP daemon deactivated. LLDP configuration (lldpPortConfigTable)
is kept and is still accessible. Configuration changes will not take
effect until lldpActivated is 'True'. | ||||
| NeventSystem | 1.3.6.1.4.1.16177.2.1.5.2 | |||
| SsummaryAlarmStatus | 1.3.6.1.4.1.16177.2.1.5.2.1 | INTEGER | RO | |
scalar · INTEGER · read-only · current The summaryAlarmStatus reports ''warning'' when at least one
of the configured alarm/event sources reports alarm condition.
WeOS supports an extensive set of alarm/event sources and a
flexible alarm handling framework.
The sources affecting the summaryAlarmStatus are those
configured to affect the unit's status LED, typically
labeled ''ON'' and located on the unit's front panel.
| ||||
| SsummaryAlarmTrapEnabled | 1.3.6.1.4.1.16177.2.1.5.2.2 | TruthValue | RW | |
scalar · TruthValue · read-write · current Enable/Disable support for sending summaryAlarm traps.
True(1) if summaryAlarm traps are enabled.
False(2) if summaryAlarm traps are disabled.
Traps will be sent if (and only if) the summaryAlarmStatus
changes status ('warning => ok' or 'ok => warning'). | ||||
| SstatusRelay | 1.3.6.1.4.1.16177.2.1.5.2.3 | INTEGER | RO | |
scalar · INTEGER · read-only · current Displays the current state of the statusRelay (DigitalOut).
| ||||
| TalarmStatusTable | 1.3.6.1.4.1.16177.2.1.5.2.4 | NA | ||
table · not-accessible · current The status for alarm triggers. | ||||
| RalarmStatusEntry | 1.3.6.1.4.1.16177.2.1.5.2.4.1 | NA | ||
row · not-accessible · current An entry containing information about a specific alarm trigger.
| ||||
| CalarmStatusTriggerId | 1.3.6.1.4.1.16177.2.1.5.2.4.1.1 | INTEGER (0..255) | RO | |
column · INTEGER (0..255) · read-only · current The id of alarm trigger | ||||
| CalarmStatusTriggerType | 1.3.6.1.4.1.16177.2.1.5.2.4.1.2 | DisplayString (SIZE (0..255)) | RO | |
column · DisplayString (SIZE (0..255)) · read-only · current A text string containing description about the trigger type | ||||
| CalarmStatusTriggerEnabled | 1.3.6.1.4.1.16177.2.1.5.2.4.1.3 | TruthValue | RO | |
column · TruthValue · read-only · current Indicates if the trigger is enabled or not | ||||
| CalarmStatusTriggerStatus | 1.3.6.1.4.1.16177.2.1.5.2.4.1.4 | INTEGER | RO | |
column · INTEGER · read-only · current The actual alarm status for the trigger
| ||||
| CalarmStatusTriggerStatusReason | 1.3.6.1.4.1.16177.2.1.5.2.4.1.5 | DisplayString (SIZE (0..255)) | RO | |
column · DisplayString (SIZE (0..255)) · read-only · current A text string containing status reason | ||||
| Nstatistics | 1.3.6.1.4.1.16177.2.1.5.3 | |||
| SmemoryAvail | 1.3.6.1.4.1.16177.2.1.5.3.1 | Integer32 | RO | |
scalar · Integer32 · read-only · current Displays the amount of available memory in kb for the system. | ||||
| NcpuLoadAvg | 1.3.6.1.4.1.16177.2.1.5.3.2 | |||
| SloadAvg1 | 1.3.6.1.4.1.16177.2.1.5.3.2.1 | Integer32 | RO | |
scalar · Integer32 · read-only · current Displays a the cpu load average over 1 minute. The value is displayed by taking the cpu load avgerage value and multiplying it with 100. | ||||
| SloadAvg5 | 1.3.6.1.4.1.16177.2.1.5.3.2.2 | Integer32 | RO | |
scalar · Integer32 · read-only · current Displays a the cpu load average over 5 minutes. The value is displayed by taking the cpu load avgerage value and multiplying it with 100. | ||||
| SloadAvg15 | 1.3.6.1.4.1.16177.2.1.5.3.2.3 | Integer32 | RO | |
scalar · Integer32 · read-only · current Displays a the cpu load average over 15 minute. The value is displayed by taking the cpu load avgerage value and multiplying it with 100. | ||||
| Nintegrity | 1.3.6.1.4.1.16177.2.1.5.4 | |||
| SstartupConfigurationHash | 1.3.6.1.4.1.16177.2.1.5.4.1 | DisplayString | RO | |
scalar · DisplayString · read-only · current A SHA-1 hash of the saved startup configuration. | ||||
| SrunningConfigurationHash | 1.3.6.1.4.1.16177.2.1.5.4.2 | DisplayString | RO | |
scalar · DisplayString · read-only · current A SHA-1 hash of the current running configuration. | ||||
| Nnotifications | 1.3.6.1.4.1.16177.2.1.6 | |||
| NsensorNotifications | 1.3.6.1.4.1.16177.2.1.6.1 | |||
| NsensorNotificationPrefix | 1.3.6.1.4.1.16177.2.1.6.1.0 | |||
| !digitalInHigh | 1.3.6.1.4.1.16177.2.1.6.1.0.1 | |||
notification · current Notification associated with digitalIn sensor state. Sensor is of type TruthValue. The 'entPhySensorValue' should always have value 'true(1)' in a digitalInHigh trap, indicating that the voltage level is above the required threshold (logical 1).
| ||||
| !digitalInLow | 1.3.6.1.4.1.16177.2.1.6.1.0.2 | |||
notification · current Notification associated with digitalIn sensor state. Sensor is of type TruthValue. The 'entPhySensorValue' should always have value 'false(2)' in a digitalInLow trap, indicating that the voltage level is below the required threshold (logical 0).
| ||||
| !powerSupplyHigh | 1.3.6.1.4.1.16177.2.1.6.1.0.3 | |||
notification · current Notification associated with power supply sensor state. Sensor is of type TruthValue The 'entPhySensorValue' should always have value 'true(1)' in a powerSupplyHigh trap, indicating that the voltage level is above the required threshold.
| ||||
| !powerSupplyLow | 1.3.6.1.4.1.16177.2.1.6.1.0.4 | |||
notification · current Notification associated with power supply sensor state. Sensor is of type TruthValue The 'entPhySensorValue' should always have value 'false(2)' in a powerSupplyLow trap, indicating that the voltage level is below the required threshold.
| ||||
| !temperatureHigh | 1.3.6.1.4.1.16177.2.1.6.1.0.5 | |||
notification · current Notification associated with temperature sensor state.
Sensor is of type 'Celsius'.
The 'entPhySensorValue' shows the temperature value at
the time the alarm system detected that the temperature had
rised to or passed beyond the configured alarm rising
threshold; except for temperatureHigh alarms at system
startup, this would typically be equal to the temperature
configured as the alarm rising threshold. | ||||
| !temperatureLow | 1.3.6.1.4.1.16177.2.1.6.1.0.6 | |||
notification · current Notification associated with temperature sensor state.
Sensor is of type 'Celsius'.
The 'entPhySensorValue' shows the temperature value at
the time the alarm system detected that the temperature had
fallen to or passed below the configured alarm falling
threshold; except for temperatureLow alarms at system
startup, this would typically be equal to the temperature
configured as the alarm falling threshold. | ||||
| NfrntNotifications | 1.3.6.1.4.1.16177.2.1.6.2 | |||
| NfrntNotificationPrefix | 1.3.6.1.4.1.16177.2.1.6.2.0 | |||
| !frntv0RingUp | 1.3.6.1.4.1.16177.2.1.6.2.0.1 | |||
notification · current Notification associated with FRNTv0 ring status. The 'frntv0RingStatus' should always have value 'ring(1)' in an frntv0RingUp trap. Note that a focal point can detect both local failures and elsewhere in the FRNT ring, while a member switch is only able to detect local failures. | ||||
| !frntv0RingDown | 1.3.6.1.4.1.16177.2.1.6.2.0.2 | |||
notification · current Notification associated with FRNTv0 ring status. The 'frntv0RingStatus' should always have value 'bus(2)' in an frntv0RingDown trap. Note that a focal point can detect both local failures and elsewhere in the FRNT ring, while a member switch is only able to detect local failures. | ||||
| NlffNotifications | 1.3.6.1.4.1.16177.2.1.6.3 | |||
| NlffNotificationPrefix | 1.3.6.1.4.1.16177.2.1.6.3.0 | |||
| !lffRemoteUp | 1.3.6.1.4.1.16177.2.1.6.3.0.1 | |||
notification · current Notification associated with link fault forward of remote (Ethernet) link over an intermediate (SHDSL) link. The 'lffStatus' should always have value 'remoteUp(4)' in a lffRemoteUp, indicating that remote (Ethernet) link is up.
| ||||
| !lffRemoteFail | 1.3.6.1.4.1.16177.2.1.6.3.0.2 | |||
notification · current Notification associated with link fault forward of remote
(Ethernet) link over an intermediate (SHDSL) link.
The 'lffStatus' will show value
- 'remoteDown(3)' when information that the remote
(Ethernet) link is down is available.
- 'unknown(2)' when there is no information about the
state of the remote available, typically because the
intermediate (SHDSL) link is down.
| ||||
| NgenericNotifications | 1.3.6.1.4.1.16177.2.1.6.4 | |||
| NgenericNotificationPrefix | 1.3.6.1.4.1.16177.2.1.6.4.0 | |||
| !summaryStatusOK | 1.3.6.1.4.1.16177.2.1.6.4.0.1 | |||
notification · current Notification that _none_ of the configured alarm sources
reports a bad state, i.e.,
- that the summaryAlarmStatus has _shifted_ from 'Warning
(1)' to 'Ok (2)', or
- that the unit started up with summaryStatus 'Ok (2)'.
| ||||
| !summaryStatusWarning | 1.3.6.1.4.1.16177.2.1.6.4.0.2 | |||
notification · current Notification that at least one of the configured alarm
sources reports a bad state, i.e.,
- that the summaryAlarmStatus has _shifted_ from 'Ok (2)' to
'Warning (1)', or
- that the unit started up with summaryStatus 'Warning (1)'.
| ||||
| NddmNotifications | 1.3.6.1.4.1.16177.2.1.6.5 | |||
| NddmNotificationPrefix | 1.3.6.1.4.1.16177.2.1.6.5.0 | |||
| !ddmVoltageHigh | 1.3.6.1.4.1.16177.2.1.6.5.0.1 | |||
notification · current Notification associated with DDM voltage sensor state. The 'sfpDdmPortVoltage' shows the voltage value at the time the alarm system detected that the voltage had rised to or passed beyond the configured alarm rising threshold. | ||||
| !ddmVoltageLow | 1.3.6.1.4.1.16177.2.1.6.5.0.2 | |||
notification · current Notification associated with DDM voltage sensor state. The 'sfpDdmPortVoltage' shows the voltage value at the time the alarm system detected that the voltage had fallen to or passed below the configured alarm falling threshold. | ||||
| !ddmTemperatureHigh | 1.3.6.1.4.1.16177.2.1.6.5.0.3 | |||
notification · current Notification associated with DDM temperature sensor state. The 'sfpDdmPortTemperature' shows the temperature value at the time the alarm system detected that the temperature had rised to or passed beyond the configured alarm rising threshold. | ||||
| !ddmTemperatureLow | 1.3.6.1.4.1.16177.2.1.6.5.0.4 | |||
notification · current Notification associated with DDM temperature sensor state. The 'sfpDdmPortTemperature' shows the temperature value at the time the alarm system detected that the temperature had fallen to or passed below the configured alarm falling threshold. | ||||
| !ddmBiasCurrentHigh | 1.3.6.1.4.1.16177.2.1.6.5.0.5 | |||
notification · current Notification associated with DDM transmitt bias current sensor state. The 'sfpDdmPortBiasCurrent' shows the bias current value at the time the alarm system detected that the bias current had rised to or passed beyond the configured alarm rising threshold. | ||||
| !ddmBiasCurrentLow | 1.3.6.1.4.1.16177.2.1.6.5.0.6 | |||
notification · current Notification associated with DDM transmitt bias current sensor state. The 'sfpDdmPortBiasCurrent' shows the bias current value at the time the alarm system detected that the bias current had fallen to or passed below the configured alarm falling threshold. | ||||
| !ddmTxPowerHigh | 1.3.6.1.4.1.16177.2.1.6.5.0.7 | |||
notification · current Notification associated with DDM transmitt power sensor state. The 'sfpDdmPortTxPower' shows the power value at the time the alarm system detected that the power had rised to or passed beyond the configured alarm rising threshold. | ||||
| !ddmTxPowerLow | 1.3.6.1.4.1.16177.2.1.6.5.0.8 | |||
notification · current Notification associated with DDM transmitt power sensor state. The 'sfpDdmPortTxPower' shows the power value at the time the alarm system detected that the power had fallen to or passed below the configured alarm falling threshold. | ||||
| !ddmRxPowerHigh | 1.3.6.1.4.1.16177.2.1.6.5.0.9 | |||
notification · current Notification associated with DDM receiving power sensor state. The 'sfpDdmPortRxPower' shows the power value at the time the alarm system detected that the power had rised to or passed beyond the configured alarm rising threshold. | ||||
| !ddmRxPowerLow | 1.3.6.1.4.1.16177.2.1.6.5.0.10 | |||
notification · current Notification associated with DDM receiving power sensor state. The 'sfpDdmPortRxPower' shows the power value at the time the alarm system detected that the power had fallen to or passed below the configured alarm falling threshold. | ||||
| NconflictNotifications | 1.3.6.1.4.1.16177.2.1.6.6 | |||
| NconflictNotificationPrefix | 1.3.6.1.4.1.16177.2.1.6.6.0 | |||
| !addressConflictDetected | 1.3.6.1.4.1.16177.2.1.6.6.0.1 | |||
notification · current An Address Conflict have been detected. | ||||
| !addressConflictCleared | 1.3.6.1.4.1.16177.2.1.6.6.0.2 | |||
notification · current An Address Conflict have been resolved. | ||||
| !addressConflictOK | 1.3.6.1.4.1.16177.2.1.6.6.0.3 | |||
notification · current There are no Address Conflicts. This trap is sent when the last conflict is resolved.
| ||||
| !addressConflictWarning | 1.3.6.1.4.1.16177.2.1.6.6.0.4 | |||
notification · current An address conflict exists. This trap is sent when the first address conflict is detected.
| ||||
| NotherNotifications | 1.3.6.1.4.1.16177.2.1.6.7 | |||
| NotherNotificationPrefix | 1.3.6.1.4.1.16177.2.1.6.7.0 | |||
| !mrpRingClosed | 1.3.6.1.4.1.16177.2.1.6.7.0.3 | |||
| !mrpRingOpen | 1.3.6.1.4.1.16177.2.1.6.7.0.4 | |||
| NriCoNotifications | 1.3.6.1.4.1.16177.2.1.6.8 | |||
| NriCoNotificationPrefix | 1.3.6.1.4.1.16177.2.1.6.8.0 | |||
| !riCoUplinkUp | 1.3.6.1.4.1.16177.2.1.6.8.0.1 | |||
notification · current A RiCo or Dual Homing uplink has come up. The riCoStatusUplinkStatus shows if the link comes up in role Active or Backup. | ||||
| !riCoUplinkDown | 1.3.6.1.4.1.16177.2.1.6.8.0.2 | |||
notification · current A RiCo or Dual Homing uplink has gone down. The riCoStatusUplinkStatus shows 'Down'. | ||||
| NpingNotifications | 1.3.6.1.4.1.16177.2.1.6.9 | |||
| NpingNotificationPrefix | 1.3.6.1.4.1.16177.2.1.6.9.0 | |||
| !pingTriggerOk | 1.3.6.1.4.1.16177.2.1.6.9.0.1 | |||
| !pingTriggerWarning | 1.3.6.1.4.1.16177.2.1.6.9.0.2 | |||
Traps / Notifications
- addressConflictCleared
1.3.6.1.4.1.16177.2.1.6.6.0.2 - addressConflictDetected
1.3.6.1.4.1.16177.2.1.6.6.0.1 - addressConflictOK
1.3.6.1.4.1.16177.2.1.6.6.0.3 - addressConflictWarning
1.3.6.1.4.1.16177.2.1.6.6.0.4 - ddmBiasCurrentHigh
1.3.6.1.4.1.16177.2.1.6.5.0.5 - ddmBiasCurrentLow
1.3.6.1.4.1.16177.2.1.6.5.0.6 - ddmRxPowerHigh
1.3.6.1.4.1.16177.2.1.6.5.0.9 - ddmRxPowerLow
1.3.6.1.4.1.16177.2.1.6.5.0.10 - ddmTemperatureHigh
1.3.6.1.4.1.16177.2.1.6.5.0.3 - ddmTemperatureLow
1.3.6.1.4.1.16177.2.1.6.5.0.4 - ddmTxPowerHigh
1.3.6.1.4.1.16177.2.1.6.5.0.7 - ddmTxPowerLow
1.3.6.1.4.1.16177.2.1.6.5.0.8 - ddmVoltageHigh
1.3.6.1.4.1.16177.2.1.6.5.0.1 - ddmVoltageLow
1.3.6.1.4.1.16177.2.1.6.5.0.2 - digitalInHigh
1.3.6.1.4.1.16177.2.1.6.1.0.1 - digitalInLow
1.3.6.1.4.1.16177.2.1.6.1.0.2 - frntv0RingDown
1.3.6.1.4.1.16177.2.1.6.2.0.2 - frntv0RingUp
1.3.6.1.4.1.16177.2.1.6.2.0.1 - lffRemoteFail
1.3.6.1.4.1.16177.2.1.6.3.0.2 - lffRemoteUp
1.3.6.1.4.1.16177.2.1.6.3.0.1 - mrpRingClosed
1.3.6.1.4.1.16177.2.1.6.7.0.3 - mrpRingOpen
1.3.6.1.4.1.16177.2.1.6.7.0.4 - pingTriggerOk
1.3.6.1.4.1.16177.2.1.6.9.0.1 - pingTriggerWarning
1.3.6.1.4.1.16177.2.1.6.9.0.2 - powerSupplyHigh
1.3.6.1.4.1.16177.2.1.6.1.0.3 - powerSupplyLow
1.3.6.1.4.1.16177.2.1.6.1.0.4 - riCoUplinkDown
1.3.6.1.4.1.16177.2.1.6.8.0.2 - riCoUplinkUp
1.3.6.1.4.1.16177.2.1.6.8.0.1 - summaryStatusOK
1.3.6.1.4.1.16177.2.1.6.4.0.1 - summaryStatusWarning
1.3.6.1.4.1.16177.2.1.6.4.0.2 - temperatureHigh
1.3.6.1.4.1.16177.2.1.6.1.0.5 - temperatureLow
1.3.6.1.4.1.16177.2.1.6.1.0.6