UBQS-REDUNDANCY-MIB
Premier Network Co., LtdThe UBQS-REDUNDANCY-MIB is used to monitor and configure the redundancy appliances.
snmptranslate -m UBQS-REDUNDANCY-MIB -Tpsnmpwalk -v2c -c <community> -m UBQS-REDUNDANCY-MIB <host> 1.3.6.1.4.1.7800.100.29Imports
| IF-MIB | InterfaceIndex, InterfaceIndexOrZero |
|---|---|
| INET-ADDRESS-MIB | InetAddress, InetAddressPrefixLength, InetAddressType |
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP |
| SNMPv2-SMI | Bits, Counter32, Gauge32, Integer32, IpAddress, MODULE-IDENTITY, MibIdentifier, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, iso |
| SNMPv2-TC | DisplayString, PhysAddress, TEXTUAL-CONVENTION, TimeStamp, TruthValue |
| UBQS-SMI | ubiMgmtv2 |
OID tree
| Name | OID | Type | Access | Status |
|---|---|---|---|---|
| IubiRedundancyMIB | 1.3.6.1.4.1.7800.100.29 | |||
identity The UBQS-REDUNDANCY-MIB is used to monitor and configure the redundancy appliances. | ||||
| NubiRedundancyMIBNotificationPrefix | 1.3.6.1.4.1.7800.100.29.0 | |||
| !ubiSwitchOverNotification | 1.3.6.1.4.1.7800.100.29.0.1 | |||
notification · current The agent generates this trap when a switchover occurs. | ||||
| !ubiRedundancyConnectionStateNotification | 1.3.6.1.4.1.7800.100.29.0.2 | |||
notification · current The agent generates this trap when the connection state of standby appliance device is changed.
| ||||
| !ubiRedundancySyncNotification | 1.3.6.1.4.1.7800.100.29.0.3 | |||
notification · current The agent generates this trap when the synchronization process with standby SCU is done. This notification occurs after standby is connected.
| ||||
| !ubiRedundancySyncStateChangeNotification | 1.3.6.1.4.1.7800.100.29.0.4 | |||
notification · current The agent generates this trap when the synchronization state has been changed.
| ||||
| NubiRedundancyObjects | 1.3.6.1.4.1.7800.100.29.1 | |||
| NubiRedundancy | 1.3.6.1.4.1.7800.100.29.1.1 | |||
| SubiRedundancyReload | 1.3.6.1.4.1.7800.100.29.1.1.1 | INTEGER | RW | |
scalar · INTEGER · read-write · current Reload Active/Standby or Peer device.
| ||||
| SubiRedundancyMyRedundancyState | 1.3.6.1.4.1.7800.100.29.1.1.2 | RedundancyState | RO | |
scalar · RedundancyState · read-only · current The HA redundancy state of this appliance device. | ||||
| TubiRedundancyTable | 1.3.6.1.4.1.7800.100.29.1.1.3 | NA | ||
table · not-accessible · current This table keeps the current configuration of the redundancy information of the active and standby units. | ||||
| RubiRedundancyEntry | 1.3.6.1.4.1.7800.100.29.1.1.3.1 | NA | ||
row · not-accessible · current An entry containing redundancy information of the active and standby units | ||||
| CubiRedundancyIsActivePreferred | 1.3.6.1.4.1.7800.100.29.1.1.3.1.1 | TruthValue | NA | |
column · TruthValue · not-accessible · current This status indicates whether this appliance device is preferred to active or not. Commonly upper(or left) device has this value as True(1) and low(or right) device has this value as False(0). | ||||
| CubiRedundancyState | 1.3.6.1.4.1.7800.100.29.1.1.3.1.2 | RedundancyState | RO | |
column · RedundancyState · read-only · current The HA redundancy state of the appliance device. Role states for redundancy. Valid values are : notConfigured (1) The appliance is not configured for redundancy. active (2) The appliance is the active appliance. standby (3) The appliance is warm standby mode activeLostStandby (4) The active appliance is not getting any response from the standby appliance. | ||||
| CubiRedundancyConnectionState | 1.3.6.1.4.1.7800.100.29.1.1.3.1.3 | INTEGER | AN | |
column · INTEGER · accessible-for-notify · current The HA redundancy connection state of standby appliance device.
| ||||
| SubiRedundancyConnStateNotificationEnabled | 1.3.6.1.4.1.7800.100.29.1.1.4 | TruthValue | RW | |
scalar · TruthValue · read-write · current Enable or disable redundancy connection state notification via SNMP. | ||||
| TubiRedundancySyncTable | 1.3.6.1.4.1.7800.100.29.1.1.5 | NA | ||
table · not-accessible · current This table keeps the information of the redundancy sync state of the active and standby units. | ||||
| RubiRedundancySyncEntry | 1.3.6.1.4.1.7800.100.29.1.1.5.1 | NA | ||
row · not-accessible · current An entry containing redundancy sync information of the active and standby units | ||||
| CubiRedundancySyncState | 1.3.6.1.4.1.7800.100.29.1.1.5.1.1 | INTEGER | AN | |
column · INTEGER · accessible-for-notify · current The redundancy sync state of active appliance device for standby. This sync state is related with 'redundancy-check' function. ACTIVE periodically checks sync state with STANDBY using this function. Valid values are : sync (1) synchronized with standby. notSync (2) some mismatch occurs with standby.
| ||||
| CubiRedundancySyncNotificationEnabled | 1.3.6.1.4.1.7800.100.29.1.1.5.1.2 | TruthValue | RW | |
column · TruthValue · read-write · current Enable or disable redundancy sync notification via SNMP. | ||||
| CubiRedundancySyncStateChangeNotificationEnabled | 1.3.6.1.4.1.7800.100.29.1.1.5.1.3 | TruthValue | RW | |
column · TruthValue · read-write · current Enable or disable redundancy sync state change notification via SNMP. | ||||
| TubiRedundancyAddrTable | 1.3.6.1.4.1.7800.100.29.1.2 | NA | ||
table · not-accessible · current This table keeps the current configuration of the address information of the active and standby appliances. There is an entry in this table corresponding to each network interface that is configured for redundancy. Thus, the number of entries in this table corresponds to the number of interfaces configured for redundancy. | ||||
| RubiRedundancyAddrEntry | 1.3.6.1.4.1.7800.100.29.1.2.1 | NA | ||
row · not-accessible · current An entry containing address information for redundancy configuration on a network interface. | ||||
| CubiRedundancyAddrIfIndex | 1.3.6.1.4.1.7800.100.29.1.2.1.1 | InterfaceIndex | RO | |
column · InterfaceIndex · read-only · current The index value which uniquely identifies the interface to which this entry is applicable. | ||||
| CubiRedundancyAddrMyAddressType | 1.3.6.1.4.1.7800.100.29.1.2.1.2 | InetAddressType | RO | |
column · InetAddressType · read-only · current The type of address stored in ubiMyAddressType. | ||||
| CubiRedundancyAddrMyAddress | 1.3.6.1.4.1.7800.100.29.1.2.1.3 | InetAddress | RO | |
column · InetAddress · read-only · current The IP address of the interface configured for this HA configuration in this appliance. The type of this mib variable is defined in ubiMyAddressType. | ||||
| CubiRedundancyAddrPeerAddressType | 1.3.6.1.4.1.7800.100.29.1.2.1.4 | InetAddressType | RO | |
column · InetAddressType · read-only · current The type of address stored in ubiPeerAddressType | ||||
| CubiRedundancyAddrPeerAddress | 1.3.6.1.4.1.7800.100.29.1.2.1.5 | InetAddress | RO | |
column · InetAddress · read-only · current The IP address of the interface configured for this HA configuration in the peer appliance. The type of this mib variable is defined in ubiPeerAddressType. | ||||
| NubiRedundancyPeerObjects | 1.3.6.1.4.1.7800.100.29.2 | |||
| NubiPeerSysInfo | 1.3.6.1.4.1.7800.100.29.2.1 | |||
| SubiPeerSWVersion | 1.3.6.1.4.1.7800.100.29.2.1.1 | DisplayString | RO | |
scalar · DisplayString · read-only · current Software version of the peer HA system | ||||
| SubiPeerSerialNumber | 1.3.6.1.4.1.7800.100.29.2.1.2 | DisplayString | RO | |
scalar · DisplayString · read-only · current Serial Number of the peer HA system | ||||
| SubiPeerPhysicalAddress | 1.3.6.1.4.1.7800.100.29.2.1.3 | PhysAddress | RO | |
scalar · PhysAddress · read-only · current Peer's physical address. | ||||
| NubiPeerResource | 1.3.6.1.4.1.7800.100.29.2.2 | |||
| SubiPeerCpuFiveSec | 1.3.6.1.4.1.7800.100.29.2.2.1 | Counter32 | NA | |
scalar · Counter32 · not-accessible · current CPU busy percentage in the last 5 second period.
| ||||
| SubiPeerCpuOneMin | 1.3.6.1.4.1.7800.100.29.2.2.2 | Counter32 | RO | |
scalar · Counter32 · read-only · current CPU busy percentage in the last 1 minute period.
| ||||
| SubiPeerCpuFiveMin | 1.3.6.1.4.1.7800.100.29.2.2.3 | Counter32 | RO | |
scalar · Counter32 · read-only · current CPU busy percentage in the last 5 minute period.
| ||||
| SubiPeerMemoryAlloc | 1.3.6.1.4.1.7800.100.29.2.2.4 | Counter32 | NA | |
scalar · Counter32 · not-accessible · current Memory allocation usage.
| ||||
| SubiPeerMemoryFree | 1.3.6.1.4.1.7800.100.29.2.2.5 | Counter32 | RO | |
scalar · Counter32 · read-only · current Memory free usage.
| ||||
| SubiPeerMemoryTotal | 1.3.6.1.4.1.7800.100.29.2.2.6 | Counter32 | RO | |
scalar · Counter32 · read-only · current CPU busy percentage in the last 5 minute period.
| ||||
| SubiPeerMemoryFreePercentage | 1.3.6.1.4.1.7800.100.29.2.2.7 | Counter32 | RO | |
scalar · Counter32 · read-only · current It indicates available memory allocation space in percentage.
| ||||
| NubiPeerEnvironment | 1.3.6.1.4.1.7800.100.29.2.3 | |||
| SubiPeerTemperature | 1.3.6.1.4.1.7800.100.29.2.3.1 | Gauge32 | RO | |
scalar · Gauge32 · read-only · current peer's current temperature.
| ||||
| NubiPeerBootInfo | 1.3.6.1.4.1.7800.100.29.2.4 | |||
| SubiPeerNextBootImage | 1.3.6.1.4.1.7800.100.29.2.4.1 | DisplayString | RW | |
scalar · DisplayString · read-write · current Booting OS Image's name for peer unit when setting this object, It should be specified the file name with path under /flash directory and Peer's next booting mode will be Flash booting. Valid paths under /flash directory are : - os1/ - os2/ e.g) os1/BootImageName.Z | ||||
| NubiPeerImageModify | 1.3.6.1.4.1.7800.100.29.2.4.2 | |||
| SubiPeerImagePath | 1.3.6.1.4.1.7800.100.29.2.4.2.1 | INTEGER | RW | |
scalar · INTEGER · read-write · current warning : It operates for only Active unit, not Standby Unit.
Path of the file that you want to copy or erase.
Represents 'copy (os1:|os2:) peer <FILENAME>' or
'erase (os1:|os2:) peer <FILENAME>' CLIs.
for copy operation, path of Active unit and
for erase operation, path of Standby unit.
| ||||
| SubiPeerImageFileName | 1.3.6.1.4.1.7800.100.29.2.4.2.2 | DisplayString | RW | |
scalar · DisplayString · read-write · current warning : It operates for only Active unit, not Standby Unit. Name of the file that you want to copy or erase. for copy operation, file name at Active unit and for erase operation, file anme at Standby unit. | ||||
| SubiPeerImageModifyOperate | 1.3.6.1.4.1.7800.100.29.2.4.2.3 | INTEGER | WO | |
scalar · INTEGER · write-only · current execute to copy or erase configurations.
| ||||
| NubiSwitchoverObjects | 1.3.6.1.4.1.7800.100.29.3 | |||
| NubiSwitchover | 1.3.6.1.4.1.7800.100.29.3.1 | |||
| SubiLastSwitchOverReason | 1.3.6.1.4.1.7800.100.29.3.1.1 | SwitchOverReason | RO | |
scalar · SwitchOverReason · read-only · current Reason for the most recent switchover. Valid values are : nont (0) none of the following lossConnWithActive (1) lost connection with active forcedSwitchOver (2) Switchover occurs by force unknown (3) Switchover occurs by unknown reason | ||||
| SubiLastSwitchOverTime | 1.3.6.1.4.1.7800.100.29.3.1.2 | DisplayString | RO | |
scalar · DisplayString · read-only · current The local date and time when the last switchover event occurred and was logged to the system. | ||||
| SubiSwitchoverNotificationEnabled | 1.3.6.1.4.1.7800.100.29.3.1.3 | TruthValue | RW | |
scalar · TruthValue · read-write · current Enable or disable switchover notification via SNMP. | ||||
| SubiSwitchOverRedundancySyncState | 1.3.6.1.4.1.7800.100.29.3.1.4 | INTEGER | RO | |
scalar · INTEGER · read-only · current The HA redundancy sync state of the appliance device after switchover. Valid values are : sync (1) SCU synchronization is done . notSync (2) SCU synchronization is fail or still in progress.
| ||||
| NubiRedundancyMIBConformance | 1.3.6.1.4.1.7800.100.29.4 | |||
| NubiRedundancyMIBCompliance | 1.3.6.1.4.1.7800.100.29.4.1 | |||
| MubiRedundancyMIBCompliances | 1.3.6.1.4.1.7800.100.29.4.1.1 | |||
compliance · current An Redundancy-MIB implementation can implement this group to provide Redundancy properties. | ||||
| NubiRedundancyMIBGroups | 1.3.6.1.4.1.7800.100.29.4.2 | |||
| NubiRedundancyMIBRedundancyGroup | 1.3.6.1.4.1.7800.100.29.4.2.1 | |||
| NubiRedundancyMIBSwitchoverGroup | 1.3.6.1.4.1.7800.100.29.4.2.2 | |||
| NubiRedundancyMIBNotificationGroup | 1.3.6.1.4.1.7800.100.29.4.2.3 | |||
Textual conventions
FlashPathINTEGERconfig(2)os1(0)os2(1)Represents 'copy <source> peer'.
RedundancyStateINTEGERactive(2)activeLostStandby(4)notConfigured(1)standby(3)Role states for redundancy. Valid values are : notConfigured (1) The appliance is not configured for redundancy. active (2) The appliance is the active appliance. standby (3) The appliance is warm standby mode activeLostStandby (4) The active appliance is not getting any response from the standby appliance.
SwitchOverReasonINTEGERforcedSwitchOver(2)lossConnWithActive(1)none(0)unknown(3)Role states for redundancy. Valid values are : none (0) none of the following lossConnWithActive (1) lost connection with active forcedSwitchOver (2) Switchover occurs by force unknown (3) Switchover occurs by unknown reason
Traps / Notifications
- ubiRedundancyConnectionStateNotification
1.3.6.1.4.1.7800.100.29.0.2 - ubiRedundancySyncNotification
1.3.6.1.4.1.7800.100.29.0.3 - ubiRedundancySyncStateChangeNotification
1.3.6.1.4.1.7800.100.29.0.4 - ubiSwitchOverNotification
1.3.6.1.4.1.7800.100.29.0.1