UBQS-CFM-MIB
Premier Network Co., LtdConnectivity Fault Management module for managing IEEE 802.1ag
snmptranslate -m UBQS-CFM-MIB -Tpsnmpwalk -v2c -c <community> -m UBQS-CFM-MIB <host> 1.3.6.1.4.1.7800.100.10Imports
| IF-MIB | ifIndex |
|---|---|
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP |
| SNMPv2-SMI | Bits, Counter32, Gauge32, Integer32, IpAddress, MODULE-IDENTITY, MibIdentifier, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, iso |
| SNMPv2-TC | DisplayString, MacAddress, PhysAddress, RowStatus, TEXTUAL-CONVENTION, TruthValue |
| UBQS-LAG-MIB | ubiAggId |
| UBQS-SMI | ubiMgmtv2 |
OID tree
| Name | OID | Type | Access | Status |
|---|---|---|---|---|
| IubiCFMMIB | 1.3.6.1.4.1.7800.100.10 | |||
identity Connectivity Fault Management module for managing IEEE 802.1ag | ||||
| NubiCFMMIBNotificationPrefix | 1.3.6.1.4.1.7800.100.10.0 | |||
| NubiCfmNotifications | 1.3.6.1.4.1.7800.100.10.0.0 | |||
| !ubiCfmRemoteMepStatusChange | 1.3.6.1.4.1.7800.100.10.0.0.1 | |||
notification · current Remote MEP state(CC state) change Notification | ||||
| !ubiCfmAggPortRemoteMepStatusChange | 1.3.6.1.4.1.7800.100.10.0.0.2 | |||
notification · current Notification that Remote MEP state(CC state) on port-gruop change | ||||
| !ubiCfmPmFrameDelayEvent | 1.3.6.1.4.1.7800.100.10.0.0.3 | |||
notification · current To generate notification when ubiCfmMepPmCurrentValue is bigger than ubiCfmMaPmDelayThreshold | ||||
| !ubiCfmPmFrameLossEvent | 1.3.6.1.4.1.7800.100.10.0.0.4 | |||
notification · current To generate notification when ubiCfmMepPmCurrentValue is bigger than ubiCfmMaPmLossThreshold | ||||
| !ubiCfmMepEtherPingSendResult | 1.3.6.1.4.1.7800.100.10.0.0.5 | |||
notification · current Indicates the result of the operation: - ok The Loopback Message(s)reply received - fail The Loopback Message(s)reply don't recieved - already active Another LBM is being transmitted - Not ready Do not initator state machine for LBM sending
| ||||
| !ubiCfmMepLinkTraceSendResult | 1.3.6.1.4.1.7800.100.10.0.0.6 | |||
notification · current A LTR information about LTMs transmitted | ||||
| !ubiCfmCCConfigDefectAlarm | 1.3.6.1.4.1.7800.100.10.0.0.7 | |||
notification · current The CCM defect about Config error | ||||
| NubiCFMMIBObjects | 1.3.6.1.4.1.7800.100.10.1 | |||
| NubiCfmMd | 1.3.6.1.4.1.7800.100.10.1.1 | |||
| TubiCfmMdTable | 1.3.6.1.4.1.7800.100.10.1.1.1 | NA | ||
table · not-accessible · current The Maintenance Domain table. Each row in the table represents a different Maintenance Domain. A Maintenance Domain is described in 802.1ag (3.22) as the network or the part of the network for which faults in connectivity are to be managed. The boundary of a Maintenance Domain is defined by a set of DSAPs, each of which can become a point of connectivity to a service instance | ||||
| RubiCfmMdEntry | 1.3.6.1.4.1.7800.100.10.1.1.1.1 | NA | ||
row · not-accessible · current The Maintenance Domain table entry.
INDEX { ubiBridgeId, ubiCfmMdIndex }
| ||||
| CubiCfmMdIndex | 1.3.6.1.4.1.7800.100.10.1.1.1.1.1 | Unsigned32 | NA | |
column · Unsigned32 · not-accessible · current The index to the Maintenance Domain table. | ||||
| CubiCfmMdName | 1.3.6.1.4.1.7800.100.10.1.1.1.1.2 | Dot1agCfmMaintDomainName | RC | |
column · Dot1agCfmMaintDomainName · read-create · current The Maintenance Domain name. Each Maintenance Domain has unique name amongst all those used or available to a service provider or operator. It facilitates easy identification of administrative responsibility for each Maintenance Domain. | ||||
| CubiCfmMdNameType | 1.3.6.1.4.1.7800.100.10.1.1.1.1.3 | Dot1agCfmMaintDomainNameType2 | RC | |
column · Dot1agCfmMaintDomainNameType2 · read-create · current The type (and thereby format) of the Maintenance Domain Name. There are two types. IEEE802.1ag type(string, address...etc) and ITU-T Y.1731 type (itu-t) | ||||
| CubiCfmMdLevel | 1.3.6.1.4.1.7800.100.10.1.1.1.1.4 | Dot1agCfmMDLevel | RC | |
column · Dot1agCfmMDLevel · read-create · current The Maintenance Domain Level. (0 ~ 7 level) | ||||
| CubiCfmMdMipCreation | 1.3.6.1.4.1.7800.100.10.1.1.1.1.5 | Dot1agCfmMhfCreation | RC | |
column · Dot1agCfmMhfCreation · read-create · current Enumerated value indicating whether the management entity can create MHFs (MIP Half Function) for this Maintenance Domain. Since, in this variable, there is no encompassing Maintenance Domain, the value defMHFdefer is not allowed.
| ||||
| CubiCfmMdRowStatus | 1.3.6.1.4.1.7800.100.10.1.1.1.1.6 | RowStatus | RC | |
column · RowStatus · read-create · current The status of the row. | ||||
| TubiCfmDefaultMdTable | 1.3.6.1.4.1.7800.100.10.1.1.2 | NA | ||
table · not-accessible · current For each bridge component, the Default MD Level Managed Object controls MHF creation for VIDs that are not attached to a specific Maintenance Association Managed Object, and Sender ID TLV transmission by those MHFs. For each Bridge Port, and for each VLAN ID whose data can pass through that Bridge Port, an entry in this table is used by the algorithm in subclause 22.2.3 only if there is no entry in the Maintenance Association table defining an MA for the same VLAN ID and MD Level as this table's entry, and on which MA an Up MEP is defined. If there exists such an MA, that MA's objects are used by the algorithm in subclause 22.2.3 in place of this table entry's objects. The agent maintains the value of ubiCfmDefaultMdRowStatus to indicate whether this entry is overridden by an MA. When first initialized, the agent creates this table automatically with entries for all VLAN IDs, with the default values specified for each object. | ||||
| RubiCfmDefaultMdEntry | 1.3.6.1.4.1.7800.100.10.1.1.2.1 | NA | ||
row · not-accessible · current The Default MD Level table entry. | ||||
| CubiCfmDefaultMdVlanId | 1.3.6.1.4.1.7800.100.10.1.1.2.1.1 | VlanIndex | NA | |
column · VlanIndex · not-accessible · current The Primary VID of the VLAN to which this entry's objects apply. | ||||
| CubiCfmDefaultMdLevel | 1.3.6.1.4.1.7800.100.10.1.1.2.1.2 | Dot1agCfmMDLevel | RC | |
column · Dot1agCfmMDLevel · read-create · current A value indicating the MD Level at which MHFs are to be created, and Sender ID TLV transmission by those MHFs is to be controlled, for the VLAN to which this entry's objects apply. If this object has the value -1, the MD Level for MHF creation for this VLAN is controlled by ubiCfmDefaultMdLevel. | ||||
| CubiCfmDefaultMdMipCreation | 1.3.6.1.4.1.7800.100.10.1.1.2.1.3 | Dot1agCfmMhfCreation | RC | |
column · Dot1agCfmMhfCreation · read-create · current A value indicating if the Management entity can create MHFs (MIP Half Function) for this VID at this MD Level. If this object has the value defMHFdefer, MHF creation for this VLAN is controlled by dot1agCfmDefaultMdDefMhfCreation. The value of this variable is meaningless if the values of ubiCfmDefaultMdMipCreation is false.
| ||||
| CubiCfmDefaultMdRowStatus | 1.3.6.1.4.1.7800.100.10.1.1.2.1.4 | RowStatus | RC | |
column · RowStatus · read-create · current The status of the row. | ||||
| NubiCfmMa | 1.3.6.1.4.1.7800.100.10.1.2 | |||
| TubiCfmMaTable | 1.3.6.1.4.1.7800.100.10.1.2.1 | NA | ||
table · not-accessible · current The Maintenance Association table. Each row in the table represents an MA. An MA is a set of MEPs, each configured with a single service instance. | ||||
| RubiCfmMaEntry | 1.3.6.1.4.1.7800.100.10.1.2.1.1 | NA | ||
| CubiCfmMaIndex | 1.3.6.1.4.1.7800.100.10.1.2.1.1.1 | Unsigned32 | NA | |
column · Unsigned32 · not-accessible · current The index to the Maintenance Association table. | ||||
| CubiCfmMaName | 1.3.6.1.4.1.7800.100.10.1.2.1.1.2 | Dot1agCfmMaintAssocName | RC | |
column · Dot1agCfmMaintAssocName · read-create · current The Short Maintenance Association name. This name MUST be unique within a maintenance domain. | ||||
| CubiCfmMaNameType | 1.3.6.1.4.1.7800.100.10.1.2.1.1.3 | Dot1agCfmMaintAssocNameType | RC | |
column · Dot1agCfmMaintAssocNameType · read-create · current The type (and thereby format) of the Maintenance Association Name. | ||||
| CubiCfmMaVlanId | 1.3.6.1.4.1.7800.100.10.1.2.1.1.4 | VlanIndex | RC | |
column · VlanIndex · read-create · current The Primary VLAN ID with which the Maintenance Association is associated, or 0 if the MA is not attached to any VID. | ||||
| CubiCfmMaMipCreation | 1.3.6.1.4.1.7800.100.10.1.2.1.1.5 | Dot1agCfmMhfCreation | RC | |
column · Dot1agCfmMhfCreation · read-create · current Indicates if the Management entity can create MHFs (MIP Half Function) for this MA.
| ||||
| CubiCfmMaRowStatus | 1.3.6.1.4.1.7800.100.10.1.2.1.1.6 | RowStatus | RC | |
column · RowStatus · read-create · current The status of the row. | ||||
| TubiCfmMaAttrTable | 1.3.6.1.4.1.7800.100.10.1.2.2 | NA | ||
table · not-accessible · current An Attribute table for each MA(Maintenance Association). Such as, CCM transmission interval. | ||||
| RubiCfmMaAttrEntry | 1.3.6.1.4.1.7800.100.10.1.2.2.1 | NA | ||
| CubiCfmMaAttrCCInterval | 1.3.6.1.4.1.7800.100.10.1.2.2.1.1 | Integer32 | RW | |
column · Integer32 · read-write · current Interval between CCM transmissions to be used by all MEPs in the MA. interval3ms(1) CCMs are sent every 3 1/3 milliseconds. interval10ms(2) CCMs are sent every 10 milliseconds. interval100ms(3) CCMs are sent every 100 milliseconds. interval1s(4) CCMs are sent every 1 second. interval10s(5) CCMs are sent every 10 seconds. interval1min(6) CCMs are sent every minute. interval10min(7) CCMs are sent every 10 minutes. | ||||
| TubiCfmMaPmTable | 1.3.6.1.4.1.7800.100.10.1.2.3 | NA | ||
table · not-accessible · current An attribute for Performance Monitoring | ||||
| RubiCfmMaPmEntry | 1.3.6.1.4.1.7800.100.10.1.2.3.1 | NA | ||
row · not-accessible · current Performance Monitoring Entry | ||||
| CubiCfmMaPmDelayInterval | 1.3.6.1.4.1.7800.100.10.1.2.3.1.1 | Integer32 | RW | |
column · Integer32 · read-write · current Interval to trasmit DM(delay measurement)message | ||||
| CubiCfmMaPmLossInterval | 1.3.6.1.4.1.7800.100.10.1.2.3.1.2 | Integer32 | RW | |
column · Integer32 · read-write · current Interval to trasmit LM(loss measurement)message | ||||
| CubiCfmMaPmDelayThreshold | 1.3.6.1.4.1.7800.100.10.1.2.3.1.3 | Integer32 | RW | |
column · Integer32 · read-write · current Treshold to limit for delay | ||||
| CubiCfmMaPmLossThreshold | 1.3.6.1.4.1.7800.100.10.1.2.3.1.4 | Integer32 | RW | |
column · Integer32 · read-write · current Treshold to limit for loss | ||||
| NubiCfmRmep | 1.3.6.1.4.1.7800.100.10.1.3 | |||
| TubiCfmRmepTable | 1.3.6.1.4.1.7800.100.10.1.3.1 | NA | ||
table · not-accessible · current Information of Remote Mep table | ||||
| RubiCfmRmepEntry | 1.3.6.1.4.1.7800.100.10.1.3.1.1 | NA | ||
row · not-accessible · current Information of Remote Mep entry
| ||||
| CubiCfmRmepId | 1.3.6.1.4.1.7800.100.10.1.3.1.1.1 | Dot1agCfmMepId | NA | |
column · Dot1agCfmMepId · not-accessible · current Maintenance association End Point Identifier of a remote MEP | ||||
| CubiCfmRmepVlanId | 1.3.6.1.4.1.7800.100.10.1.3.1.1.2 | VlanIndex | RW | |
column · VlanIndex · read-write · current VLAN Identifier of a remote MEP. Same value of local MEP(MA's VID) | ||||
| CubiCfmRmepRemoteMacAddr | 1.3.6.1.4.1.7800.100.10.1.3.1.1.3 | MacAddress | RW | |
column · MacAddress · read-write · current The MAC address of the remote MEP. | ||||
| CubiCfmRmepCrossCheckType | 1.3.6.1.4.1.7800.100.10.1.3.1.1.4 | INTEGER | RW | |
column · INTEGER · read-write · current CrossCheck Type (uicast or multicast).
| ||||
| CubiCfmRmepStatus | 1.3.6.1.4.1.7800.100.10.1.3.1.1.5 | INTEGER | RO | |
column · INTEGER · read-only · current Continuity Status to local MEP from remote MEP. Remote MEP state machine last entered either the RMEP_FAILED or RMEP_OK state
| ||||
| CubiCfmRmepRowStatus | 1.3.6.1.4.1.7800.100.10.1.3.1.1.6 | RowStatus | RC | |
column · RowStatus · read-create · current The status of the row. | ||||
| NubiCfmMep | 1.3.6.1.4.1.7800.100.10.1.4 | |||
| TubiCfmMepTable | 1.3.6.1.4.1.7800.100.10.1.4.1 | NA | ||
table · not-accessible · current The Maintenance Association End Point (MEP) table. | ||||
| RubiCfmMepEntry | 1.3.6.1.4.1.7800.100.10.1.4.1.1 | NA | ||
row · not-accessible · current The known MEPS table entry. | ||||
| CubiCfmMepId | 1.3.6.1.4.1.7800.100.10.1.4.1.1.1 | Dot1agCfmMepId | NA | |
column · Dot1agCfmMepId · not-accessible · current Integer that is unique among all the MEPs in the same MA. Other definition is: A small integer, unique over a given Maintenance Association, identifying a specific Maintenance association End Point (3.19). MEP Identifier is also known as the MEPID. | ||||
| CubiCfmMepMdLevel | 1.3.6.1.4.1.7800.100.10.1.4.1.1.2 | Dot1agCfmMDLevel | RW | |
column · Dot1agCfmMDLevel · read-write · current MD level that belong to this MD | ||||
| CubiCfmMepVlanId | 1.3.6.1.4.1.7800.100.10.1.4.1.1.3 | VlanIndex | RW | |
column · VlanIndex · read-write · current An integer indicating the Primary VID of the MEP, always one of the VIDs assigned to the MEP's MA. The value 0 indicates that either the Primary VID is that of the MEP's MA, or that the MEP's MA is associated with no VID. | ||||
| CubiCfmMepActive | 1.3.6.1.4.1.7800.100.10.1.4.1.1.4 | TruthValue | RW | |
column · TruthValue · read-write · current Administrative state of the MEP. A Boolean indicating the
administrative state of the MEP.
True indicates that the MEP is to function normally, and
false that it is to cease functioning. | ||||
| CubiCfmMepDirection | 1.3.6.1.4.1.7800.100.10.1.4.1.1.5 | INTEGER | RW | |
column · INTEGER · read-write · current The direction in which the MEP faces on the Bridge port.
| ||||
| CubiCfmMepMdName | 1.3.6.1.4.1.7800.100.10.1.4.1.1.6 | Dot1agCfmMaintDomainName | RW | |
column · Dot1agCfmMaintDomainName · read-write · current MD name that belong to this MD | ||||
| CubiCfmMepUniMep | 1.3.6.1.4.1.7800.100.10.1.4.1.1.7 | INTEGER | RW | |
column · INTEGER · read-write · current The flag to configure UNI-MEP
| ||||
| CubiCfmMepRmepId | 1.3.6.1.4.1.7800.100.10.1.4.1.1.8 | Dot1agCfmMepId | RW | |
column · Dot1agCfmMepId · read-write · current The specified RmepID that is RMEP configured | ||||
| CubiCfmMepIfname | 1.3.6.1.4.1.7800.100.10.1.4.1.1.9 | DisplayString | RO | |
column · DisplayString · read-only · current This object is the IfIndex of the interface where MEP configure. | ||||
| CubiCfmMepIfMacAddr | 1.3.6.1.4.1.7800.100.10.1.4.1.1.10 | MacAddress | RO | |
column · MacAddress · read-only · current Thsi object is the MAC address of the interface where MEP configure. | ||||
| CubiCfmMepRdi | 1.3.6.1.4.1.7800.100.10.1.4.1.1.11 | TruthValue | RO | |
column · TruthValue · read-only · current State of the RDI bit in the sending CCM (true for RDI=1), or false. | ||||
| CubiCfmMepCCType | 1.3.6.1.4.1.7800.100.10.1.4.1.1.12 | INTEGER | RW | |
column · INTEGER · read-write · current The type of CCM message.
| ||||
| CubiCfmMepCCEnable | 1.3.6.1.4.1.7800.100.10.1.4.1.1.13 | INTEGER | RW | |
column · INTEGER · read-write · current If set to true, the MEP will generate CCM messages.
| ||||
| CubiCfmMepRowStatus | 1.3.6.1.4.1.7800.100.10.1.4.1.1.14 | RowStatus | RC | |
column · RowStatus · read-create · current The status of the row. | ||||
| CubiCfmMepMissingTime | 1.3.6.1.4.1.7800.100.10.1.4.1.1.15 | Integer32 | RO | |
column · Integer32 · read-only · current The pass time after received last CCM | ||||
| CubiCfmMepExpiredTime | 1.3.6.1.4.1.7800.100.10.1.4.1.1.16 | Integer32 | RO | |
column · Integer32 · read-only · current The remain time till Expired RMEP status | ||||
| CubiCfmMepForceEgressTag | 1.3.6.1.4.1.7800.100.10.1.4.1.1.17 | INTEGER | RW | |
column · INTEGER · read-write · current UNI-MEP send CCM with VID information(tagged) or send CCM without VID information (untagged). If set none-value, tag information is depend on egress interface policy
| ||||
| TubiCfmMepPmDelayTable | 1.3.6.1.4.1.7800.100.10.1.4.2 | NA | ||
table · not-accessible · current Performance Monitoring Table | ||||
| RubiCfmMepPmDelayEntry | 1.3.6.1.4.1.7800.100.10.1.4.2.1 | NA | ||
row · not-accessible · current Performance Monitoring Entry | ||||
| CubiCfmMepPmDelayRmep | 1.3.6.1.4.1.7800.100.10.1.4.2.1.1 | INTEGER | RC | |
column · INTEGER · read-create · current Remote MEP ID to measure performance | ||||
| CubiCfmMepPmDelayFrameType | 1.3.6.1.4.1.7800.100.10.1.4.2.1.2 | INTEGER | RC | |
column · INTEGER · read-create · current The type of frame that is to measure
| ||||
| CubiCfmMepPmDelayCurrentValue | 1.3.6.1.4.1.7800.100.10.1.4.2.1.3 | Unsigned32 | RO | deprecated |
column · Unsigned32 · read-only · deprecated Result value of measurement | ||||
| CubiCfmMepPmDelayTxInterval | 1.3.6.1.4.1.7800.100.10.1.4.2.1.4 | INTEGER | RC | |
column · INTEGER · read-create · current Period that operate performance monitoring
| ||||
| CubiCfmMepPmDelayState | 1.3.6.1.4.1.7800.100.10.1.4.2.1.5 | INTEGER | RO | |
column · INTEGER · read-only · current Result state of measurement. If ubiCfmMepPmCurrentValue is lower than threshold, ubiCfmMepPmState is OK. If ubiCfmMepPmCurrentValue is over the configured threshold, ubiCfmMepPmState is FAIL.
| ||||
| CubiCfmMepPmDelayRowStatus | 1.3.6.1.4.1.7800.100.10.1.4.2.1.6 | RowStatus | RC | |
column · RowStatus · read-create · current The status of the row. | ||||
| CubiCfmMepPmDelayMin | 1.3.6.1.4.1.7800.100.10.1.4.2.1.7 | Integer32 | RO | |
column · Integer32 · read-only · current Minimum delay measured by performance monitoring
| ||||
| CubiCfmMepPmDelayMax | 1.3.6.1.4.1.7800.100.10.1.4.2.1.8 | Integer32 | RO | |
column · Integer32 · read-only · current Maximum delay measured by performance monitoring
| ||||
| CubiCfmMepPmDelayAvg | 1.3.6.1.4.1.7800.100.10.1.4.2.1.9 | Integer32 | RO | |
column · Integer32 · read-only · current Average of delay measured by performance monitoring
| ||||
| TubiCfmMepPmLossTable | 1.3.6.1.4.1.7800.100.10.1.4.3 | NA | ||
table · not-accessible · current Performance Monitoring Table | ||||
| RubiCfmMepPmLossEntry | 1.3.6.1.4.1.7800.100.10.1.4.3.1 | NA | ||
row · not-accessible · current Performance Monitoring Entry | ||||
| CubiCfmMepPmLossRmep | 1.3.6.1.4.1.7800.100.10.1.4.3.1.1 | INTEGER | RC | |
column · INTEGER · read-create · current Remote MEP ID to measure performance | ||||
| CubiCfmMepPmLossFrameType | 1.3.6.1.4.1.7800.100.10.1.4.3.1.2 | INTEGER | RC | |
column · INTEGER · read-create · current The type of frame that is to measure
| ||||
| CubiCfmMepPmLossCurrentValue | 1.3.6.1.4.1.7800.100.10.1.4.3.1.3 | Unsigned32 | RO | deprecated |
column · Unsigned32 · read-only · deprecated Result value of measurement | ||||
| CubiCfmMepPmLossTxInterval | 1.3.6.1.4.1.7800.100.10.1.4.3.1.4 | INTEGER | RC | |
column · INTEGER · read-create · current Period that operate performance monitoring
| ||||
| CubiCfmMepPmLossState | 1.3.6.1.4.1.7800.100.10.1.4.3.1.5 | INTEGER | RO | |
column · INTEGER · read-only · current Result state of measurement. If ubiCfmMepPmCurrentValue is lower than threshold, ubiCfmMepPmState is OK. If ubiCfmMepPmCurrentValue is over the configured threshold, ubiCfmMepPmState is FAIL.
| ||||
| CubiCfmMepPmLossRowStatus | 1.3.6.1.4.1.7800.100.10.1.4.3.1.6 | RowStatus | RC | |
column · RowStatus · read-create · current The status of the row. | ||||
| CuniCfmMepPmLossNearEndTot | 1.3.6.1.4.1.7800.100.10.1.4.3.1.7 | Integer32 | RO | |
column · Integer32 · read-only · current Frame loss of near end measured by performance monitoring | ||||
| CuniCfmMepPmLossFarEndTot | 1.3.6.1.4.1.7800.100.10.1.4.3.1.8 | Integer32 | RO | |
column · Integer32 · read-only · current Frame loss of far end measured by performance monitoring | ||||
| CubiCfmMepPmLossRttMin | 1.3.6.1.4.1.7800.100.10.1.4.3.1.9 | Integer32 | RO | |
column · Integer32 · read-only · current Minimum route-trip time between MEPs | ||||
| CubiCfmMepPmLossRttMax | 1.3.6.1.4.1.7800.100.10.1.4.3.1.10 | Integer32 | RO | |
column · Integer32 · read-only · current Maximum route-trip time between MEPs | ||||
| CubiCfmMepPmLossRttAvg | 1.3.6.1.4.1.7800.100.10.1.4.3.1.11 | Integer32 | RO | |
column · Integer32 · read-only · current Average of route-trip time between MEPs | ||||
| NubiCfmMepOamSend | 1.3.6.1.4.1.7800.100.10.1.4.4 | |||
| SubiCfmMepOamSendBridgeId | 1.3.6.1.4.1.7800.100.10.1.4.4.1 | Integer32 | RW | |
scalar · Integer32 · read-write · current Bridge ID to send Ping or Linktrace | ||||
| SubiCfmMepOamSendMdIndex | 1.3.6.1.4.1.7800.100.10.1.4.4.2 | Unsigned32 | RW | |
scalar · Unsigned32 · read-write · current Maintenance Domain ID to send Ping or Linktrace | ||||
| SubiCfmMepOamSendMaIndex | 1.3.6.1.4.1.7800.100.10.1.4.4.3 | Unsigned32 | RW | |
scalar · Unsigned32 · read-write · current Maintenance Association ID to send Ping or Linktrace | ||||
| SubiCfmMepOamSendMepId | 1.3.6.1.4.1.7800.100.10.1.4.4.4 | Unsigned32 | RW | |
scalar · Unsigned32 · read-write · current MEP ID to send Ping or Linktrace | ||||
| SubiCfmMepOamSendDstMac | 1.3.6.1.4.1.7800.100.10.1.4.4.5 | MacAddress | RW | |
scalar · MacAddress · read-write · current Destination MAC address | ||||
| SubiCfmMepOamSendLoopbackFrameType | 1.3.6.1.4.1.7800.100.10.1.4.4.6 | INTEGER | RW | |
scalar · INTEGER · read-write · current Type of CFM loopback Frame (ETH-LB)
| ||||
| SubiCfmMepOamSendLoopbackFrameCount | 1.3.6.1.4.1.7800.100.10.1.4.4.7 | Counter32 | RW | |
scalar · Counter32 · read-write · current Counter to transmit CFM loopback frame | ||||
| SubiCfmMepOamSendExecute | 1.3.6.1.4.1.7800.100.10.1.4.4.8 | INTEGER | RW | |
scalar · INTEGER · read-write · current Send ping/linktrace messages
| ||||
| NubiCfmMepOamResult | 1.3.6.1.4.1.7800.100.10.1.4.5 | |||
| SubiCfmMepOamResultEtherPing | 1.3.6.1.4.1.7800.100.10.1.4.5.1 | INTEGER | AN | |
scalar · INTEGER · accessible-for-notify · current The result of Loopback message sent. If already Loopback function activate, send trap result value on already_activated. if CC not connected or unicast RMEP crosscheck type, send trap result value on not_ready.
| ||||
| SubiCfmMepOamResultEtherPingSndCount | 1.3.6.1.4.1.7800.100.10.1.4.5.2 | Counter32 | AN | |
scalar · Counter32 · accessible-for-notify · current Counter of CFM loopback frame to send | ||||
| SubiCfmMepOamResultEtherPingRcvCount | 1.3.6.1.4.1.7800.100.10.1.4.5.3 | Counter32 | AN | |
scalar · Counter32 · accessible-for-notify · current Received counter of CFM lopback reply | ||||
| SubiCfmMepOamResultEtherPingRttMin | 1.3.6.1.4.1.7800.100.10.1.4.5.4 | Integer32 | AN | |
scalar · Integer32 · accessible-for-notify · current Minimum round-trip time measured by CFM loopback frame | ||||
| SubiCfmMepOamResultEtherPingRttMax | 1.3.6.1.4.1.7800.100.10.1.4.5.5 | Integer32 | AN | |
scalar · Integer32 · accessible-for-notify · current Maximum round-trip time measured by CFM loopback frame | ||||
| SubiCfmMepOamResultEtherPingRttAvg | 1.3.6.1.4.1.7800.100.10.1.4.5.6 | Integer32 | AN | |
scalar · Integer32 · accessible-for-notify · current Average of round-trip time measured by CFM loopback frame | ||||
| SubiCfmMepOamResultLinkTraceSrcMacAddr | 1.3.6.1.4.1.7800.100.10.1.4.5.7 | MacAddress | AN | |
scalar · MacAddress · accessible-for-notify · current MAC address returned in the ingress MAC address field. | ||||
| SubiCfmMepOamResultLinkTraceRcvIfIndex | 1.3.6.1.4.1.7800.100.10.1.4.5.8 | Integer32 | AN | |
scalar · Integer32 · accessible-for-notify · current The index of local interface of received LTR | ||||
| SubiCfmMepOamResultLinkTraceRelayAction | 1.3.6.1.4.1.7800.100.10.1.4.5.9 | INTEGER | AN | |
scalar · INTEGER · accessible-for-notify · current Indicates if a LTM was forwarded by the responding MP, as returned in the 'relay-hit' or 'relay-fdb' flag of the flags field. If other LT function already activate, on already_activated value. else if CC is not OK state, on not_ready value
| ||||
| SubiCfmMepOamResultLinkTraceHopCount | 1.3.6.1.4.1.7800.100.10.1.4.5.10 | Integer32 | AN | |
scalar · Integer32 · accessible-for-notify · current hop count for a returned LTR. | ||||
| TubiCfmCCConfigDefectTable | 1.3.6.1.4.1.7800.100.10.1.4.6 | NA | ||
table · not-accessible · current The CCM config defect table | ||||
| RubiCfmCCConfigDefectEntry | 1.3.6.1.4.1.7800.100.10.1.4.6.1 | NA | ||
row · not-accessible · current The CCM config defect entry | ||||
| CubiCfmMepCCConfigDefect | 1.3.6.1.4.1.7800.100.10.1.4.6.1.1 | INTEGER | RO | |
column · INTEGER · read-only · current Number of Defect 0: None 1: Unexpected MEP ID 2: Unexpected Tx interval 3: Already Existed MEP
| ||||
| CubiCfmMepCCConfigDefectState | 1.3.6.1.4.1.7800.100.10.1.4.6.1.2 | INTEGER | RO | |
column · INTEGER · read-only · current State of defect condition 0: DefectConditionExit 1: DefectConditionEntry
| ||||
| NubiCfmServerMep | 1.3.6.1.4.1.7800.100.10.1.5 | |||
| TubiCfmServerMepTable | 1.3.6.1.4.1.7800.100.10.1.5.1 | NA | ||
table · not-accessible · current A Server MEP represents the compound function of the
Server layer termination function and Server/ETH adaptation
function which is used to notify the ETH layer MEPs upon
failure detection by the Server layer termination function or
Server/ETH adaptation function, where the Server layer
termination function is expected to run OAM mechanisms specific
to the Server layer.
A Server MEP needs to support ETH-AIS function, as described
in clause 7.4, where the Server/ETH adaptation function is
required to issue frames with ETH-AIS information upon detection of
defect at the Server layer by the Server layer termination
and/or adaptation function.
(ITU-T Y.1731 5.3.1) | ||||
| RubiCfmServerMepEntry | 1.3.6.1.4.1.7800.100.10.1.5.1.1 | NA | ||
| CubiCfmServerMepTxInterval | 1.3.6.1.4.1.7800.100.10.1.5.1.1.1 | INTEGER (1 | 60) | RW | |
column · INTEGER (1 | 60) · read-write · current Periodic Interval of AIS Transmission | ||||
| CubiCfmServerMepAisLevel | 1.3.6.1.4.1.7800.100.10.1.5.1.1.2 | Dot1agCfmMDLevel | RW | |
column · Dot1agCfmMDLevel · read-write · current Destinaction Maintenance Domain Level of AIS | ||||
| CubiCfmServerMepRowStatus | 1.3.6.1.4.1.7800.100.10.1.5.1.1.3 | RowStatus | RC | |
column · RowStatus · read-create · current The status of the row. | ||||
| NubiCfmNotificationEnables | 1.3.6.1.4.1.7800.100.10.1.6 | |||
| SubiCfmRemoteMepStateChangeEnabled | 1.3.6.1.4.1.7800.100.10.1.6.1 | TruthValue | RW | |
scalar · TruthValue · read-write · current Remote MEP state(CC state) change Notification | ||||
| SubiCfmPmEventEnabled | 1.3.6.1.4.1.7800.100.10.1.6.2 | TruthValue | RW | |
scalar · TruthValue · read-write · current ubiCfmMepPmState change Notification | ||||
| SubiCfmCCConfigDefectAlarmEnabled | 1.3.6.1.4.1.7800.100.10.1.6.3 | TruthValue | RW | |
scalar · TruthValue · read-write · current Detect CCM config Defect notification | ||||
| NubiCfmTrack | 1.3.6.1.4.1.7800.100.10.1.7 | |||
| SubiCfmTrackEnable | 1.3.6.1.4.1.7800.100.10.1.7.1 | Bits | RW | |
scalar · Bits · read-write · current Not use
| ||||
| TubiCfmTrackTargetTable | 1.3.6.1.4.1.7800.100.10.1.7.2 | NA | ||
table · not-accessible · current Not use | ||||
| RubiCfmTrackTargetEntry | 1.3.6.1.4.1.7800.100.10.1.7.2.1 | NA | ||
| CubiCfmTrackTargetSet | 1.3.6.1.4.1.7800.100.10.1.7.2.1.1 | INTEGER | RW | |
column · INTEGER · read-write · current Not use
| ||||
| NubiCFMMIBConformance | 1.3.6.1.4.1.7800.100.10.2 | |||
| NubiCfmMIBCompliances | 1.3.6.1.4.1.7800.100.10.2.1 | |||
| MubiVlanMIBCompliance | 1.3.6.1.4.1.7800.100.10.2.1.1 | |||
| NubiCfmMIBGroups | 1.3.6.1.4.1.7800.100.10.2.2 | |||
| NubiCfmMaGroup | 1.3.6.1.4.1.7800.100.10.2.2.1 | |||
Textual conventions
Dot1afCfmIndexIntegerNextFreeUnsigned32 (0..4294967295)Display hint:
dAn integer which may be used as a new Index in a table. The special value of 0 indicates that no more new entries can be created in the relevant table. When a MIB is used for configuration, an object with this SYNTAX always contains a legal value (if non-zero) for an index that is not currently used in the relevant table. The Command Generator (Network Management Application) reads this variable and uses the (non-zero) value read when creating a new row with an SNMP SET. When the SET is performed, the Command Responder (agent) MUST determine whether the value is indeed still unused; Two Network Management Applications may attempt to create a row (configuration entry) simultaneously and use the same value. If it is currently unused, the SET succeeds and the Command Responder (agent) changes the value of this object, according to an implementation-specific algorithm. If the value is in use, however, the SET fails. The Network Management Application MUST then re-read this variable to obtain a new usable value. An OBJECT-TYPE definition using this SYNTAX MUST specify the relevant table for which the object is providing this functionality.
Dot1agCfmAisDefectTypeINTEGERall(1)loc(2)merge(3)none(0)unExpMegLvl(5)unExpMep(4)unExpPeriod(6)Kind of defect. It is reason why alram cuase.
Dot1agCfmCcmIntervalINTEGERinterval100ms(3)interval10min(7)interval10ms(2)interval10s(5)interval1min(6)interval1s(4)interval300Hz(1)intervalInvalid(0)Indicates the interval at which CCMs are sent by a MEP. The possible values are: intervalInvalid(0) No CCMs are sent (disabled). interval300Hz(1) CCMs are sent every 3 1/3 milliseconds (300Hz). interval10ms(2) CCMs are sent every 10 milliseconds. interval100ms(3) CCMs are sent every 100 milliseconds. interval1s(4) CCMs are sent every 1 second. interval10s(5) CCMs are sent every 10 seconds. interval1min(6) CCMs are sent every minute. interval10min(7) CCMs are sent every 10 minutes. Note: enumerations start at zero to match the 'CCM Interval field' protocol field.Dot1agCfmConfigErrorsBitscfmLeak(0)conflictingVids(1)excessiveLevels(2)overlappedLevels(3)While making the MIP creation evaluation described in 802.1ag clause 22.2.3, the management entity can encounter errors in the configuration. These are possible errors that can be encountered: CFMleak(0) MA x is associated with a specific VID list, one or more of the VIDs in MA x can pass through the Bridge Port, no Down MEP is configured on any Bridge Port for MA x, and some other MA y, at a higher MD Level than MA x, and associated with at least one of the VID(s) also in MA x, does have a MEP configured on the Bridge Port. conflictingVids(1) MA x is associated with a specific VID list, an Up MEP is configured on MA x on the Bridge Port, and some other MA y, associated with at least one of the VID(s) also in MA x, also has an Up MEP configured on some Bridge Port. ExcessiveLevels(2) The number of different MD Levels at which MIPs are to be created on this port exceeds the Bridge's capabilities (see subclause 22.3). OverlappedLevels(3) A MEP is created for one VID at one MD Level, but a MEP is configured on another VID at that MD Level or higher, exceeding the Bridge's capabilities.Dot1agCfmEgressActionFieldValueINTEGERegrBlocked(3)egrDown(2)egrNoTlv(0)egrOK(1)egrVid(4)Possible values returned in the egress action field
Dot1agCfmFngStateINTEGERfngDefect(2)fngDefectClearing(5)fngDefectReported(4)fngReportDefect(3)fngReset(1)Indicates the diferent states of the MEP Fault Notification Generator State Machine. fngReset(1) No defect has been present since the dot1agCfmMepFngResetTime timer expired, or since the state machine was last reset. fngDefect(2) A defect is present, but not for a long enough time to be reported (dot1agCfmMepFngAlarmTime). fngReportDefect(3) A momentary state during which the defect is reported by sending a dot1agCfmFaultAlarm notification, if that action is enabled. fngDefectReported(4) A defect is present, and some defect has been reported. fngDefectClearing(5) No defect is present, but the dot1agCfmMepFngResetTime timer has not yet expired.Dot1agCfmHighestDefectPriINTEGERdefErrorCCM(4)defMACstatus(2)defRDICCM(1)defRemoteCCM(3)defXconCCM(5)none(0)An enumerated value, equal to the contents of the variable highestDefect (20.33.9 and Table 20-1), indicating the highest-priority defect that has been present since the MEP Fault Notification Generator State Machine was last in the FNG_RESET state, either: none(0) no defects since FNG_RESET defRDICCM(1) DefRDICCM defMACstatus(2) DefMACstatus defRemoteCCM(3) DefRemoteCCM defErrorCCM(4) DefErrorCCM defXconCCM(5) DefXconCCM The value 0 is used for no defects so that additional higher priority values can be added, if needed, at a later time, and so that these values correspond with those in Dot1agCfmLowestAlarmPri.
Dot1agCfmIdPermissionINTEGERsendIdChassis(2)sendIdChassisManage(4)sendIdDefer(5)sendIdManage(3)sendIdNone(1)Indicates what, if anything, is to be included in the Sender ID TLV transmitted in CCMs, LBMs, LTMs, and LTRs. The valid values are: sendIdNone(1) The Sender ID TLV is not to be sent. sendIdChassis(2) The Chassis ID Length, Chassis ID Subtype, and Chassis ID fields of the Sender ID TLV are to be sent. sendIdManage(3) The Management Address Length and Management Address of the Sender ID TLV are to be sent. sendIdChassisManage(4) The Chassis ID Length, Chassis ID Subtype, Chassis ID, Management Address Length and Management Address fields are all to be sent. sendIdDefer(5) The contents of the Sender ID TLV are determined by the corresponding Maintenance Domain variable (dot1agCfmMaCompIdPermission).Dot1agCfmIngressActionFieldValueINTEGERingBlocked(3)ingDown(2)ingNoTlv(0)ingOk(1)ingVid(4)Possible values returned in the ingress action field.
Dot1agCfmInterfaceStatusINTEGERisDormant(5)isDown(2)isLowerLayerDown(7)isNoInterfaceStatusTLV(0)isNotPresent(6)isTesting(3)isUnknown(4)isUp(1)An enumerated value from the Interface Status TLV from the last CCM received from the last MEP. It indicates the status of the Interface within which the MEP transmitting the CCM is configured, or the next lower Interface in the Interface Stack, if the MEP is not configured within an Interface. isNoInterfaceStatusTLV(0) Indicates either that no CCM has been received or that no interface status TLV was present in the last CCM received. isUp(1) The interface is ready to pass packets. isDown(2) The interface cannot pass packets isTesting(3) The interface is in some test mode. isUnknown(4) The interface status cannot be determined for some reason. isDormant(5) The interface is not in a state to pass packets but is in a pending state, waiting for some external event. isNotPresent(6) Some component of the interface is missing isLowerLayerDown(7) The interface is down due to state of the lower layer interfaces NOTE: A 0 value is used for isNoInterfaceStatusTLV, so that these code points can be kept consistent with new code points added to ifOperStatus in the IF-MIB.Dot1agCfmLowestAlarmPriINTEGERallDef(1)errXcon(4)macRemErrXcon(2)noXcon(6)remErrXcon(3)xcon(5)An integer value specifying the lowest priority defect that is allowed to generate a Fault Alarm (20.9.5), either: allDef(1) DefRDICCM, DefMACstatus, DefRemoteCCM, DefErrorCCM, and DefXconCCM; macRemErrXcon(2) Only DefMACstatus, DefRemoteCCM, DefErrorCCM, and DefXconCCM (default); remErrXcon(3) Only DefRemoteCCM, DefErrorCCM, and DefXconCCM; errXcon(4) Only DefErrorCCM and DefXconCCM; xcon(5) Only DefXconCCM; or noXcon(6) No defects DefXcon or lower are to be reported;Dot1agCfmMDLevelInteger32 (0..7)Display hint:
dInteger identifying the Maintenance Domain Level (MD Level). Higher numbers correspond to higher Maintenance Domains, those with the greatest physical reach, with the highest values for customers' CFM PDUs. Lower numbers correspond to lower Maintenance Domains, those with more limited physical reach, with the lowest values for CFM PDUs protecting single bridges or physical links.
Dot1agCfmMDLevelOrNoneInteger32 (-1 | 0..7)Display hint:
dInteger identifying the Maintenance Domain Level (MD Level). Higher numbers correspond to higher Maintenance Domains, those with the greatest physical reach, with the highest values for customers' CFM packets. Lower numbers correspond to lower Maintenance Domains, those with more limited physical reach, with the lowest values for CFM PDUs protecting single bridges or physical links. The value (-1) is reserved to indicate that no MA Level has been assigned.
Dot1agCfmMaintAssocNameOCTET STRING (SIZE (1..256))Denotes a generic Maintenance Association Name. It is the part of the Maintenance Association Identifier which is unique within the Maintenance Domain Name and is appended to the Maintenance Domain Name to form the Maintenance Association Identifier (MAID). A Dot1agCfmMaintAssocName value is always interpreted within the context of a Dot1agCfmMaintAssocNameType value. Every usage of the Dot1agCfmMaintAssocName textual convention is required to specify the Dot1agCfmMaintAssocNameType object that provides the context. It is suggested that the Dot1agCfmMaintAssocNameType object be logically registered before the object(s) that use the Dot1agCfmMaintAssocName textual convention, if they appear in the same logical row. The value of a Dot1agCfmMaintAssocName object MUST always be consistent with the value of the associated Dot1agCfmMaintAssocNameType object. Attempts to set an Dot1agCfmMaintAssocName object to a value inconsistent with the associated Dot1agCfmMaintAssocNameType MUST fail with an inconsistentValue error. When this textual convention is used as the syntax of an index object, there may be issues with the limit of 128 sub-identifiers specified in SMIv2, IETF STD 58. In this case, the object definition MUST include a 'SIZE' clause to limit the number of potential instance sub-identifiers; otherwise the applicable constraints MUST be stated in the appropriate conceptual row DESCRIPTION clauses, or in the surrounding documentation if there is no single DESCRIPTION clause that is appropriate.
Dot1agCfmMaintAssocNameTypeINTEGERcharString(2)primaryVid(1)rfc2865VpnId(4)unsignedInt16(3)A value that represents a type (and thereby the format) of a Dot1agCfmMaintAssocName. The value can be one of the following: ieeeReserved(0) Reserved for definition by IEEE 802.1 recommend to not use zero unless absolutely needed. primaryVid(1) Primary VLAN ID. 12 bits represented in a 2-octet integer: - 4 least significant bits of the first byte contains the 4 most significant bits of the 12 bits primary VID - second byte contains the 8 least significant bits of the primary VID 0 1 2 3 4 5 6 7 8 +-+-+-+-+-+-+-+-+ |0 0 0 0| (MSB) | +-+-+-+-+-+-+-+-+ | VID LSB | +-+-+-+-+-+-+-+-+ charString(2) RFC2579 DisplayString, except that the character codes 0-31 (decimal) are not used. (1..45) octets unsignedInt16 (3) 2-octet integer/big endian rfc2865VpnId(4) RFC 2685 VPN ID 3 octet VPN authority Organizationally Unique Identifier followed by 4 octet VPN index identifying VPN according to the OUI: 0 1 2 3 4 5 6 7 8 +-+-+-+-+-+-+-+-+ | VPN OUI (MSB) | +-+-+-+-+-+-+-+-+ | VPN OUI | +-+-+-+-+-+-+-+-+ | VPN OUI (LSB) | +-+-+-+-+-+-+-+-+ |VPN Index (MSB)| +-+-+-+-+-+-+-+-+ | VPN Index | +-+-+-+-+-+-+-+-+ | VPN Index | +-+-+-+-+-+-+-+-+ |VPN Index (LSB)| +-+-+-+-+-+-+-+-+ ieeeReserved(xx) Reserved for definition by IEEE 802.1 xx values can be [5..31] and [64..255] ituReserved(xx) Reserved for definition by ITU-T Y.1731 xx values range from [32..63] To support future extensions, the Dot1agCfmMaintAssocNameType textual convention SHOULD NOT be sub-typed in object type definitions. It MAY be sub-typed in compliance statements in order to require only a subset of these address types for a compliant implementation. Implementations MUST ensure that Dot1agCfmMaintAssocNameType objects and any dependent objects (e.g., Dot1agCfmMaintAssocName objects) are consistent. An inconsistentValue error MUST be generated if an attempt to change an Dot1agCfmMaintAssocNameType object would, for example, lead to an undefined Dot1agCfmMaintAssocName value. In particular, Dot1agCfmMaintAssocNameType/Dot1agCfmMaintAssocName pairs MUST be changed together if the nameType changes. The Maintenance Domain name and Maintenance Association name, when put together into the CCM PDU, MUST total 48 octets or less. If the Dot1agCfmMaintDomainNameType object contains none(1), then the Dot1agCfmMaintAssocName object MUST be 45 octets or less in length. Otherwise, the length of the Dot1agCfmMaintDomainName object plus the length of the Dot1agCfmMaintAssocName object, added together, MUST total less than or equal to 44 octets.Dot1agCfmMaintDomainNameOCTET STRING (SIZE (1..256))Denotes a generic Maintenance Domain Name. A Dot1agCfmMaintDomainName value is always interpreted within the context of a Dot1agCfmMaintDomainNameType value. Every usage of the Dot1agCfmMaintDomainName textual convention is required to specify the Dot1agCfmMaintDomainNameType object that provides the context. It is suggested that the Dot1agCfmMaintDomainNameType object be logically registered before the object(s) that use the Dot1agCfmMaintDomainName textual convention, if they appear in the same logical row. The value of a Dot1agCfmMaintDomainName object MUST always be consistent with the value of the associated Dot1agCfmMaintDomainNameType object. Attempts to set an Dot1agCfmMaintDomainName object to a value inconsistent with the associated Dot1agCfmMaintDomainNameType MUST fail with an inconsistentValue error. When this textual convention is used as the syntax of an index object, there may be issues with the limit of 128 sub-identifiers specified in SMIv2, IETF STD 58. In this case, the object definition MUST include a 'SIZE' clause to limit the number of potential instance sub-identifiers; otherwise the applicable constraints MUST be stated in the appropriate conceptual row DESCRIPTION clauses, or in the surrounding documentation if there is no single DESCRIPTION clause that is appropriate. A value of none(1) in the associated Dot1agCfmMaintDomainNameType object means that no Maintenance Domain name is present, and the contents of the Dot1agCfmMaintDomainName object are meaningless. See the DESCRIPTION of the Dot1agCfmMaintAssocNameType TEXTUAL-CONVENTION for a discussion of the length limits on the Maintenance Domain name and Maintenance Association name.
Dot1agCfmMaintDomainNameType2INTEGERcharString(4)dnsLikeName(2)itu_t(32)macAddressAndUint(3)none(1)A value that represents a type (and thereby the format) of a Dot1agCfmMaintDomainName. The value can be one of the following: ieeeReserved(0) Reserved for definition by IEEE 802.1 recommend to not use zero unless absolutely needed. none(1) No format specified, usually because there is not (yet) a Maintenance Domain Name. In this case, a zero length OCTET STRING for the Domain Name field is acceptable. dnsLikeName(2) Domain Name like string, globally unique text string derived from a DNS name. macAddrAndUint(3) MAC address + 2-octet (unsigned) integer. charString(4) RFC2579 DisplayString, except that the character codes 0-31 (decimal) are not used. ieeeReserved(xx) Reserved for definition by IEEE 802.1 xx values can be [5..31] and [64..255] ituReserved(xx) Reserved for definition by ITU-T Y.1731 xx values range from [32..63] To support future extensions, the Dot1agCfmMaintDomainNameType textual convention SHOULD NOT be sub-typed in object type definitions. It MAY be sub-typed in compliance statements in order to require only a subset of these address types for a compliant implementation. Implementations MUST ensure that Dot1agCfmMaintDomainNameType objects and any dependent objects (e.g., Dot1agCfmMaintDomainName objects) are consistent. An inconsistentValue error MUST be generated if an attempt to change an Dot1agCfmMaintDomainNameType object would, for example, lead to an undefined Dot1agCfmMaintDomainName value. In particular, Dot1agCfmMaintDomainNameType/Dot1agCfmMaintDomainName pairs MUST be changed together if the nameType changes.Dot1agCfmMepDefectsBitsbDefErrorCCM(3)bDefMACstatus(1)bDefRDICCM(0)bDefRemoteCCM(2)bDefXconCCM(4)A MEP can detect and report a number of defects, and multiple defects can be present at the same time. These defects are: bDefRDICCM(0) A remote MEP is reported the RDI bit in its last CCM. bDefMACstatus(1) Either some remote MEP is reporting its Interface Status TLV as not isUp, or all remote MEPs are reporting a Port Status TLV that contains some value other than psUp. bDefRemoteCCM(2) The MEP is not receiving valid CCMs from at least one of the remote MEPs. bDefErrorCCM(3) The MEP has received at least one invalid CCM whose CCM Interval has not yet timed out. bDefXconCCM(4) The MEP has received at least one CCM from either another MAID or a lower MD Level whose CCM Interval has not yet timed out.Dot1agCfmMepIdUnsigned32 (1..8191)Display hint:
dMaintenance association End Point Identifier (MEPID): A small integer, unique over a given Maintenance Association, identifying a specific MEP.
Dot1agCfmMepIdOrZeroUnsigned32 (0 | 1..8191)Display hint:
dMaintenance association End Point Identifier (MEPID): A small integer, unique over a given Maintenance Association, identifying a specific MEP. The special value 0 is allowed to indicate special cases, for example that no MEPID is configured. Whenever an object is defined with this SYNTAX, then the DESCRIPTION clause of such an object MUST specify what the special value of 0 means.
Dot1agCfmMhfCreationINTEGERdefMHFdefault(2)defMHFdefer(4)defMHFexplicit(3)defMHFnone(1)Indicates if the Management Entity can create MHFs. The valid values are: defMHFnone(1) No MHFs can be created for this VID. defMHFdefault(2) MHFs can be created on this VID on any Bridge port through which this VID can pass. defMHFexplicit(3) MHFs can be created for this VID only on Bridge ports through which this VID can pass, and only if a MEP is created at some lower MD Level. defMHFdefer(4) The creation of MHFs is determined by the corresponding Maintenance Domain variable (dot1agCfmMaCompMhfCreation).Dot1agCfmMpDirectionINTEGERdown(1)up(2)Indicates the direction in which the Maintenance association (MEP or MIP) faces on the bridge port: down(1) Sends Continuity Check Messages away from the MAC Relay Entity. up(2) Sends Continuity Check Messages towards the MAC Relay Entity.Dot1agCfmPbbComponentIdentifierUnsigned32 (1..4294967295)Display hint:
dA Provider Backbone Bridge (PBB) can comprise a number of components, each of which can be managed in a manner essentially equivalent to an 802.1Q bridge. In order to access these components easily, an index is used in a number of tables. If any two tables are indexed by Dot1agCfmPbbComponentIdentifier, then entries in those tables indexed by the same value of Dot1agCfmPbbComponentIdentifier correspond to the same component.
Dot1agCfmPortStatusINTEGERpsBlocked(1)psNoPortStateTLV(0)psUp(2)An enumerated value from he Port Status TLV from the last CCM received from the last MEP. It indicates the ability of the Bridge Port on which the transmitting MEP resides to pass ordinary data, regardless of the status of the MAC (Table 21-10). psNoPortStateTLV(0) Indicates either that no CCM has been received or that no port status TLV was present in the last CCM received. psBlocked(1) Ordinary data cannot pass freely through the port on which the remote MEP resides. Value of enableRmepDefect is equal to false. psUp(2): Ordinary data can pass freely through the port on which the remote MEP resides. Value of enableRmepDefect is equal to true. NOTE: A 0 value is used for psNoPortStateTLV, so that additional code points can be added in a manner consistent with the Dot1agCfmInterfaceStatus textual convention.Dot1agCfmRelayActionFieldValueINTEGERrlyFdb(2)rlyHit(1)rlyMpdb(3)Possible values the Relay action field can take.
Dot1agCfmRemoteMepStateINTEGERrMepFailed(3)rMepIdle(1)rMepOk(4)rMepStart(2)Operational state of the remote MEP state machine. This state machine monitors the reception of valid CCMs from a remote MEP with a specific MEPID. It uses a timer that expires in 3.5 times the length of time indicated by the dot1agCfmMaNetCcmInterval object. rMepIdle(1) Momentary state during reset. rMepStart(2) The timer has not expired since the state machine was reset, and no valid CCM has yet been received. rMepFailed(3) The timer has expired, both since the state machine was reset, and since a valid CCM was received. rMepOk(4) The timer has not expired since a valid CCM was received.VlanIndexInteger32 (0..4095)The VLAN-id of a VLAN on ISL or 802.1q trunks. Modification of default parameters is allowed. Implementations are allowed to restrict the range of VLANs. For entities support up to 1024 VLANS. VLANs above 1000 are reserved for default VLANs and future use. Modification of default parameters is allowed. Creation or deletion of VLANs above 1000 is not allowed. For a new object which needs the vlan-id of a VLAN as its SYNTAX, it is suggested to import VlanIndex from Q-BRIDGE-MIB instead of importing this TC here in ubi-VTP-MIB.
Traps / Notifications
- ubiCfmAggPortRemoteMepStatusChange
1.3.6.1.4.1.7800.100.10.0.0.2 - ubiCfmCCConfigDefectAlarm
1.3.6.1.4.1.7800.100.10.0.0.7 - ubiCfmMepEtherPingSendResult
1.3.6.1.4.1.7800.100.10.0.0.5 - ubiCfmMepLinkTraceSendResult
1.3.6.1.4.1.7800.100.10.0.0.6 - ubiCfmPmFrameDelayEvent
1.3.6.1.4.1.7800.100.10.0.0.3 - ubiCfmPmFrameLossEvent
1.3.6.1.4.1.7800.100.10.0.0.4 - ubiCfmRemoteMepStatusChange
1.3.6.1.4.1.7800.100.10.0.0.1