TN-Y1564-MIB
Transition Engineering Inc.The MIB provides functionalities for system user management in TN modules.
snmptranslate -m TN-Y1564-MIB -Tpsnmpwalk -v2c -c <community> -m TN-Y1564-MIB <host> 1.3.6.1.4.1.868.2.5.154Imports
| INET-ADDRESS-MIB | InetAddress, InetAddressType |
|---|---|
| SNMP-FRAMEWORK-MIB | SnmpAdminString |
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP |
| SNMPv2-SMI | Bits, Integer32, IpAddress, MODULE-IDENTITY, MibIdentifier, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, iso |
| SNMPv2-TC | DisplayString, MacAddress, PhysAddress, RowStatus, TEXTUAL-CONVENTION, TruthValue |
| TRANSITION-SMI | tnProducts |
OID tree
| Name | OID | Type | Access | Status |
|---|---|---|---|---|
| ItnY1564MIB | 1.3.6.1.4.1.868.2.5.154 | |||
identity The MIB provides functionalities for system user management in TN modules. | ||||
| NtnY1564MIBNotifications | 1.3.6.1.4.1.868.2.5.154.1 | |||
| NtnY1564MIBObjects | 1.3.6.1.4.1.868.2.5.154.2 | |||
| NtnY1564CfgMgmt | 1.3.6.1.4.1.868.2.5.154.2.1 | |||
| TtnY1564ProfileTable | 1.3.6.1.4.1.868.2.5.154.2.1.1 | NA | ||
table · not-accessible · current This table provides configuration of SOAM Maintenance Point. | ||||
| RtnY1564ProfileEntry | 1.3.6.1.4.1.868.2.5.154.2.1.1.1 | NA | ||
row · not-accessible · current A entry in the table represents a configuration for local SOAM.
| ||||
| CtnY1564ProfileName | 1.3.6.1.4.1.868.2.5.154.2.1.1.1.1 | SnmpAdminString | NA | |
column · SnmpAdminString · not-accessible · current The name, ASCII range 33-126, of this table. | ||||
| CtnY1564ProfileDescription | 1.3.6.1.4.1.868.2.5.154.2.1.1.1.2 | DisplayString (SIZE (0..127)) | RC | |
column · DisplayString (SIZE (0..127)) · read-create · current The description of this table. | ||||
| CtnY1564DuelEnded | 1.3.6.1.4.1.868.2.5.154.2.1.1.1.3 | TruthValue | RC | |
column · TruthValue · read-create · current For future use. | ||||
| CtnY1564DstOamAware | 1.3.6.1.4.1.868.2.5.154.2.1.1.1.4 | TruthValue | RC | |
column · TruthValue · read-create · current When set, switch transmits Y.1731 DMM frames for delay measurements and Y.1731 1DM frames when this is cleared. When Traffic Type is 'Y.1731 OAM', switch transmits Y.1731 LBM frames as background traffic when DST is configured as OAM-aware, and Y.1731 TST frames when not. | ||||
| CtnY1564TrafficType | 1.3.6.1.4.1.868.2.5.154.2.1.1.1.5 | INTEGER | RC | |
column · INTEGER · read-create · current When set to 'Y.1731 OAM', this switch transmits Y.1731 OAM PDUs as background traffic, and DST is OAM-aware determines the PDU type. In the current version of the software, only one ECE can be tested at a time in this mode. When set to 'Simulated Customer', the software will generate a traffic-pattern per ECE that will hit the ECE, and use the ECE's counters to determine PASS/FAIL criteria.Besides supporting simultaneous test of multiple ECEs, 'Simulated Customer' has the advantage that the tester can see directly from the report if she has configured ECEs wrongly, since the report will show per-ECE counters and fail if an ECE under test is not hit as expected by the traffic pattern.
| ||||
| CtnY1564MegLevel | 1.3.6.1.4.1.868.2.5.154.2.1.1.1.6 | INTEGER | RC | |
column · INTEGER · read-create · current The MEG level used in generated Y.1731 OAM frames (both LBM/TST and DMM/1DM).
| ||||
| CtnY1564FrameSize | 1.3.6.1.4.1.868.2.5.154.2.1.1.1.7 | INTEGER | RC | |
column · INTEGER · read-create · current Selects the frame size of the background traffic. The frame size
does not include possible C-tag(s) added to match the ECE. Besides
standard frame sizes there are two custom selections:
MTU - The UNI's MTU will be used for the background traffic.
User-defined - custom specification of a frame size of the background traffic.
Valid range is 64 to 10236 bytes.
| ||||
| CtnY1564UserFrameSize | 1.3.6.1.4.1.868.2.5.154.2.1.1.1.8 | INTEGER (64..10236) | RC | |
column · INTEGER (64..10236) · read-create · current User defined frame size of the background traffic. Valid range is 64 to 10236 bytes. | ||||
| CtnY1564DwellTime | 1.3.6.1.4.1.868.2.5.154.2.1.1.1.9 | INTEGER | RC | |
column · INTEGER · read-create · current When a trial (a single step of a subtest) is executed, background traffic is transmitted for a certain period of time. When that period has elapsed, the Dwell Time determines how long to wait before reading hardware counters and status in order to assess the status of the trial. The required dwell time must be at least the worst-case roundtrip time, and therefore a.o. depends on the physical distance between the near and far ends. Valid range is from 100 to 10000 in steps of 100 milliseconds with a default of 500 milliseconds. | ||||
| CtnY1564SacFLR | 1.3.6.1.4.1.868.2.5.154.2.1.1.1.10 | INTEGER (0..1000) | RC | |
column · INTEGER (0..1000) · read-create · current Defines the acceptable Frame Loss Ratio. The Acceptable FLR is measured in permille. Setting this to 1000 effectively disables this check.The number is used in all enabled subtests. Only delay measurement PDUs and green background traffic undergoes FLR check. If the number of looped green frames differs from the number of transmitted green frames by more than the 'Acceptable FLR', the test is considered failing, otherwise passing.If the EVC contains multiple ECEs that matches on the same VLAN ID (UNI ingress) and the EVC uses 'Tx Lookup' equal to 'VID-PCP', the NNI ingress rules count looped traffic per NNI outer tag's PCP, and therefore provide more detailed information about which ECE is failing, than if the EVC uses 'Tx Lookup' equal to 'VID', where all looped traffic arriving on NNI is counted on the same ECE. The disadvantage of the 'VID-PCP' method is that it uses more chip resources than does the 'VID' method. Valid range is from 0 to 1000 with a default of 0‰. | ||||
| CtnY1564SacFTD | 1.3.6.1.4.1.868.2.5.154.2.1.1.1.11 | INTEGER (0..10000) | RC | |
column · INTEGER (0..10000) · read-create · current Defines the acceptable Frame Transfer Delay, measured in milliseconds. If the highest observed frame transfer delay exceeds this, the test fails. Valid range is from 0 to 10000 with a default of 0 milliseconds. A value of 0 disables this check. | ||||
| CtnY1564SacFDV | 1.3.6.1.4.1.868.2.5.154.2.1.1.1.12 | INTEGER (0..10000) | RC | |
column · INTEGER (0..10000) · read-create · current Defines the acceptable Frame Delay Variation, measured in milliseconds. If the highest observed frame delay variation exceeds this, the test fails. Valid range is from 0 to 10000 with a default of 0 milliseconds. A value of 0 disables this check. | ||||
| CtnY1564CirEnable | 1.3.6.1.4.1.868.2.5.154.2.1.1.1.13 | TruthValue | RC | |
column · TruthValue · read-create · current Set, to enable the CIR test. | ||||
| CtnY1564CirStepDuration | 1.3.6.1.4.1.868.2.5.154.2.1.1.1.14 | INTEGER (1..3600) | RC | |
column · INTEGER (1..3600) · read-create · current Each step in the CIR configuration test applies background traffic for this number of seconds. Valid range is from 1 to 3600 with a default of 10 seconds. | ||||
| CtnY1564CirDmInterval | 1.3.6.1.4.1.868.2.5.154.2.1.1.1.15 | INTEGER (100..10000) | RC | |
column · INTEGER (100..10000) · read-create · current A Y.1731 1DM or DMM frame (depending on type of test) is transmitted every so many milliseconds, in order to perform delay measurements (DM). The number should be selected so that at least three DM frames are transmitted during a trial in order to obtain delay variation results. After each trial the measured FTD and FDV is compared against the SAC's Acceptable FLR, FTD, and FDV. Valid range is from 100 to 10000 in steps of 100 milliseconds with a default of 500 milliseconds. A value of 0 effectively disables transmission of DM frames, which thereby indirectly disables the check against the SAC. | ||||
| CtnY1564CirStepCount | 1.3.6.1.4.1.868.2.5.154.2.1.1.1.16 | INTEGER (1..1000) | RC | |
column · INTEGER (1..1000) · read-create · current The number of steps (trials) used to reach CIR. If, for example, Step Count is set to 4, four trials are executed. The first runs at 25% of this ECEs share of CIR, the second at 50%, then 75%, and finally 100%. A step count of 1 corresponds to executing Y.1564's A.1 test (Simple CIR Validation Test). A step count greater than 1 corresponds to executing Y.1564's A.2 test (Step Load CIR Test). Valid range is from 1 to 1000 with a default of 4 steps. | ||||
| CtnY1564EirEnable | 1.3.6.1.4.1.868.2.5.154.2.1.1.1.17 | TruthValue | RC | |
column · TruthValue · read-create · current Set, to enable the EIR test. | ||||
| CtnY1564EirDuration | 1.3.6.1.4.1.868.2.5.154.2.1.1.1.18 | INTEGER (1..3600) | RC | |
column · INTEGER (1..3600) · read-create · current The EIR configuration test is executed in one single trial, whose duration is configured with this parameter. Valid range is from 1 to 3600 with a default of 10 seconds. | ||||
| CtnY1564EirDmInterval | 1.3.6.1.4.1.868.2.5.154.2.1.1.1.19 | INTEGER (100..10000) | RC | |
column · INTEGER (100..10000) · read-create · current A Y.1731 1DM or DMM frame (depending on type of test) is transmitted every so many milliseconds, in order to perform delay measurements (DM). The number should be selected so that at least three DM frames are transmitted during a trial in order to obtain delay variation results. After each trial the measured FTD and FDV is compared against the SAC's Acceptable FLR, FTD, and FDV. Valid range is from 100 to 10000 in steps of 100 milliseconds with a default of 500 milliseconds. A value of 0 effectively disables transmission of DM frames, which thereby indirectly disables the check against the SAC. | ||||
| CtnY1564TrafficPolicingEnable | 1.3.6.1.4.1.868.2.5.154.2.1.1.1.20 | TruthValue | RC | |
column · TruthValue · read-create · current Set, to enable the Traffic Policing test. | ||||
| CtnY1564TrafficPolicingDuration | 1.3.6.1.4.1.868.2.5.154.2.1.1.1.21 | INTEGER (1..3600) | RC | |
column · INTEGER (1..3600) · read-create · current The Traffic Policing test is executed in one single trial, whose duration is configured with this parameter. Valid range is from 1 to 3600 with a default of 10 seconds. | ||||
| CtnY1564TrafficPolicingDmInterval | 1.3.6.1.4.1.868.2.5.154.2.1.1.1.22 | INTEGER (100..10000) | RC | |
column · INTEGER (100..10000) · read-create · current A Y.1731 1DM or DMM frame (depending on type of test) is transmitted every so many milliseconds, in order to perform delay measurements (DM). The number should be selected so that at least three DM frames are transmitted during a trial in order to obtain delay variation results. After each trial the measured FTD and FDV is compared against the SAC's Acceptable FLR, FTD, and FDV. Valid range is from 100 to 10000 in steps of 100 milliseconds with a default of 500 milliseconds. A value of 0 effectively disables transmission of DM frames, which thereby indirectly disables the check against the SAC. | ||||
| CtnY1564PerfTestEnable | 1.3.6.1.4.1.868.2.5.154.2.1.1.1.23 | TruthValue | RC | |
column · TruthValue · read-create · current Set, to enable the Performance test. | ||||
| CtnY1564PerfTestDuration | 1.3.6.1.4.1.868.2.5.154.2.1.1.1.24 | INTEGER | RC | |
column · INTEGER · read-create · current The performance test is executed in one single trial, whose duration is configured with this parameter. There are Y.1564-specified standard durations and a custom duration can be specified by selecting User-defined Duration option.
| ||||
| CtnY1564PerfTestUserDuration | 1.3.6.1.4.1.868.2.5.154.2.1.1.1.25 | INTEGER (1..86400) | RC | |
column · INTEGER (1..86400) · read-create · current User defined duration. Valid range is from 1 to 86400 with a default of 900 seconds | ||||
| CtnY1564PerfTestDmInterval | 1.3.6.1.4.1.868.2.5.154.2.1.1.1.26 | INTEGER (100..10000) | RC | |
column · INTEGER (100..10000) · read-create · current A Y.1731 1DM or DMM frame (depending on type of test) is transmitted every so many milliseconds, in order to perform delay measurements (DM). The number should be selected so that at least three DM frames are transmitted during a trial in order to obtain delay variation results. After each trial the measured FTD and FDV is compared against the SAC's Acceptable FLR, FTD, and FDV. Valid range is from 100 to 10000 in steps of 100 milliseconds with a default of 500 milliseconds. A value of 0 effectively disables transmission of DM frames, which thereby indirectly disables the check against the SAC. | ||||
| CtnY1564ProfileStatus | 1.3.6.1.4.1.868.2.5.154.2.1.1.1.27 | RowStatus | RC | |
column · RowStatus · read-create · current The status of the row. The writable columns in a row can not be changed if the row is active. All columns must have a valid value before a row can be activated. | ||||
| NtnY1564ReportMgmt | 1.3.6.1.4.1.868.2.5.154.2.2 | |||
| TtnY1564ReportTable | 1.3.6.1.4.1.868.2.5.154.2.2.1 | NA | ||
table · not-accessible · current This table provides configuration of SOAM Maintenance Point. | ||||
| RtnY1564ReportEntry | 1.3.6.1.4.1.868.2.5.154.2.2.1.1 | NA | ||
row · not-accessible · current A entry in the table represents a configuration for local SOAM.
| ||||
| CtnY1564ReportName | 1.3.6.1.4.1.868.2.5.154.2.2.1.1.1 | SnmpAdminString | NA | |
column · SnmpAdminString · not-accessible · current The name, ASCII range 33-126, of this table. | ||||
| CtnY1564ReportDscr | 1.3.6.1.4.1.868.2.5.154.2.2.1.1.2 | DisplayString (SIZE (0..127)) | RO | |
column · DisplayString (SIZE (0..127)) · read-only · current The description of this table. | ||||
| CtnY1564ReportTime | 1.3.6.1.4.1.868.2.5.154.2.2.1.1.3 | DisplayString (SIZE (26)) | RO | |
column · DisplayString (SIZE (26)) · read-only · current The description of this table. | ||||
| CtnY1564ReportTftpAddrType | 1.3.6.1.4.1.868.2.5.154.2.2.1.1.4 | InetAddressType | RW | |
column · InetAddressType · read-write · current The tftp server IP address type. | ||||
| CtnY1564ReportTftpAddr | 1.3.6.1.4.1.868.2.5.154.2.2.1.1.5 | InetAddress | RW | |
column · InetAddress · read-write · current The tftp server IP address. | ||||
| CtnY1564ReportTestStatus | 1.3.6.1.4.1.868.2.5.154.2.2.1.1.6 | INTEGER | RO | |
column · INTEGER · read-only · current
| ||||
| CtnY1564ReportAction | 1.3.6.1.4.1.868.2.5.154.2.2.1.1.7 | INTEGER | RW | |
column · INTEGER · read-write · current
| ||||
| NtnY1564MIBConformance | 1.3.6.1.4.1.868.2.5.154.3 | |||