TN-MGMT-TDM-MIB
Transition Engineering Inc.snmptranslate -m TN-MGMT-TDM-MIB -Tpsnmpwalk -v2c -c <community> -m TN-MGMT-TDM-MIB <host> 1.3.6.1.4.1.868.2.5.3.0.6Imports
| ENTITY-MIB | entPhysicalIndex |
|---|---|
| IF-MIB | InterfaceIndex, InterfaceIndexOrZero |
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP |
| SNMPv2-SMI | Bits, Integer32, IpAddress, MODULE-IDENTITY, MibIdentifier, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, enterprises, iso |
| SNMPv2-TC | DisplayString, PhysAddress, TEXTUAL-CONVENTION, TimeStamp, TruthValue |
| TN-MGMT-MIB | tnInterfaceMgmt, tnMgmtNotifications |
| TRANSITION-TC | CpsConnector |
OID tree
| Name | OID | Type | Access | Status |
|---|---|---|---|---|
| !tnIfTDMAlarmIndicationSignalEvt | 1.3.6.1.4.1.868.2.5.3.0.6 | |||
notification · current A alarm indication signal event is sent when there is a warning or alarm on TDM port.
| ||||
| TtnIfTDMTable | 1.3.6.1.4.1.868.2.5.3.1.2.6 | NA | ||
table · not-accessible · current This table has entries for the TDM attributes. | ||||
| RtnIfTDMEntry | 1.3.6.1.4.1.868.2.5.3.1.2.6.1 | NA | ||
| CtnIfTDMAISTransmit | 1.3.6.1.4.1.868.2.5.3.1.2.6.1.1 | INTEGER | RW | |
column · INTEGER · read-write · current Transmit AIS(All Ones/BLUE) on Fiber(Copper) as an error signal when Copper interface(Fiber Interface) is down. When this error signal is transmitted, the AIS of the device on the other end is activated, if supported
| ||||
| CtnIfTDMAISFormat | 1.3.6.1.4.1.868.2.5.3.1.2.6.1.2 | INTEGER | RW | |
column · INTEGER · read-write · current Transmit AIS(All Ones:1111... sequence/BLUE:0101... sequence) on Fiber(Copper) as an error signal for DS3/E3/STS-1 port
| ||||
| CtnIfTDMAlarmIndicationSignal | 1.3.6.1.4.1.868.2.5.3.1.2.6.1.3 | INTEGER | RO | |
column · INTEGER · read-only · current When equal to alarm(1), this means that the other end has TAOS enabled and is currently transmitting an alarm condition. when equal to normal, this means no alarm.
| ||||
| CtnIfTDMLongHaul | 1.3.6.1.4.1.868.2.5.3.1.2.6.1.4 | INTEGER | RO | |
column · INTEGER · read-only · current This variable indicates the current position of the remote device's Short/Long haul configuration switch.
| ||||
| CtnIfTDMType | 1.3.6.1.4.1.868.2.5.3.1.2.6.1.5 | INTEGER | RO | |
column · INTEGER · read-only · current This variable indicates the type of the current device. T1=1.544MHz; E1=2.048MHz;E3 = 34.4Mb/s; DS3 = 44.7Mb/s; STS-1 = 51.8Mb/s
| ||||
| CtnIfTDMT1E1LineBuildout | 1.3.6.1.4.1.868.2.5.3.1.2.6.1.6 | INTEGER | RO | |
column · INTEGER · read-only · current The characteristics T1E1 card's copper interface.
| ||||
| CtnIfTDMDS3E3LineBuildout | 1.3.6.1.4.1.868.2.5.3.1.2.6.1.7 | INTEGER | RW | |
column · INTEGER · read-write · current The characteristics of DS3E3 card's copper interface.
| ||||
| CtnIfTDMConnectorType | 1.3.6.1.4.1.868.2.5.3.1.2.6.1.8 | CpsConnector | RO | |
column · CpsConnector · read-only · current The style of connector built into this device. | ||||
| TtnIfTDMExtTable | 1.3.6.1.4.1.868.2.5.3.1.2.9 | NA | ||
table · not-accessible · current This table has entries for the Extral TDM attributes. | ||||
| RtnIfTDMExtEntry | 1.3.6.1.4.1.868.2.5.3.1.2.9.1 | NA | ||
row · not-accessible · current A entry in the table represents Extral TDM attributes.
| ||||
| CtnIfTDMExtId | 1.3.6.1.4.1.868.2.5.3.1.2.9.1.1 | INTEGER (1..99999999) | NA | |
column · INTEGER (1..99999999) · not-accessible · current An index that uniquely identifies an entry in the tnIfTDMExtTable. This index permits the same interface to have several different channels | ||||
| CtnIfTDMExtAISTrasmit | 1.3.6.1.4.1.868.2.5.3.1.2.9.1.2 | INTEGER | RW | |
column · INTEGER · read-write · current Transmit AIS(All Ones/BLUE) on the Channel as an error signal when Copper interface(Fiber Interface) is down. When this error signal is transmitted, the AIS of the device on the other end is activated, if supported
| ||||
| CtnIfTDMExtAISFormat | 1.3.6.1.4.1.868.2.5.3.1.2.9.1.3 | INTEGER | RW | |
column · INTEGER · read-write · current Transmit AIS(All Ones:1111... sequence/BLUE:0101... sequence) on the Channel as an error signal for the pair port
| ||||
| CtnIfTDMExtAlarmIndicationSingnal | 1.3.6.1.4.1.868.2.5.3.1.2.9.1.4 | INTEGER | RO | |
column · INTEGER · read-only · current When equal to alarm(1), this means that the other end of Channel has AIS enabled and is currently transmitting an alarm condition. when equal to normal(2), this means no alarm. when equal to yellow(3), this means the other end of Channel has YELLOW enabled and is currently transmitting a YELLOW condition. when equal to red(4), this means the local end of Channel has detect a LOS on receiver.
| ||||
| CtnIfTDMExtLoopback | 1.3.6.1.4.1.868.2.5.3.1.2.9.1.5 | INTEGER | RW | |
column · INTEGER · read-write · current This variable indicates the loopback state of the current Channel
| ||||
| CtnIfTDMExtYellowTrasmit | 1.3.6.1.4.1.868.2.5.3.1.2.9.1.6 | INTEGER | RW | |
column · INTEGER · read-write · current Transmit Yellow on the Channel as an error signal when Local Copper Interface is down. When this error signal is transmitted.
| ||||
| TtnIfTDM2Table | 1.3.6.1.4.1.868.2.5.3.1.2.10 | NA | ||
table · not-accessible · current This table has entries for the TDM 2 attributes. | ||||
| RtnIfTDM2Entry | 1.3.6.1.4.1.868.2.5.3.1.2.10.1 | NA | ||
| CtnIfTDM2FiberLineNum | 1.3.6.1.4.1.868.2.5.3.1.2.10.1.1 | INTEGER | RO | |
column · INTEGER · read-only · current This variable is indicate the links number of the Fiber Port, maybe single line or dual line | ||||
| CtnIfTDM2FiberActiveLine | 1.3.6.1.4.1.868.2.5.3.1.2.10.1.2 | INTEGER | RW | |
column · INTEGER · read-write · current This variable is indicate the active fiber link, if a multi-fiber line is used for hardware redundancy
| ||||
| CtnIfTDM2FiberRevertive | 1.3.6.1.4.1.868.2.5.3.1.2.10.1.3 | INTEGER | RW | |
column · INTEGER · read-write · current This variable is used to decide whether to revertive the fiber link to primary link if applicable
| ||||
| CtnIfTDM2FiberPrimaryLinkStatus | 1.3.6.1.4.1.868.2.5.3.1.2.10.1.4 | INTEGER | RO | |
column · INTEGER · read-only · current This variable indicates the fiber port primary line link status
| ||||
| CtnIfTDM2FiberSecondaryLinkStatus | 1.3.6.1.4.1.868.2.5.3.1.2.10.1.5 | INTEGER | RO | |
column · INTEGER · read-only · current This variable indicates the fiber port secondary line link status
| ||||
| CtnIfTDM2InBandLPEnable | 1.3.6.1.4.1.868.2.5.3.1.2.10.1.6 | INTEGER | RW | |
column · INTEGER · read-write · current This variable indicates whether In-band Loopback detect is enabled
| ||||
| CtnIfTDM2InBandLPStartPatten | 1.3.6.1.4.1.868.2.5.3.1.2.10.1.7 | DisplayString | RW | |
column · DisplayString · read-write · current This binary string is used to set the In-band Loopback start Patten, such as 11000 string | ||||
| CtnIfTDM2InBandLPStopPatten | 1.3.6.1.4.1.868.2.5.3.1.2.10.1.8 | DisplayString | RW | |
column · DisplayString · read-write · current This binary string is used to set the In-band Loopback stop Patten, such as 11100 string | ||||
| CtnIfTDM2InBandPEERLPEnable | 1.3.6.1.4.1.868.2.5.3.1.2.10.1.9 | INTEGER | RW | |
column · INTEGER · read-write · current This variable indicates whether the PEER interface In-band Loopback detect is enabled
| ||||
| CtnIfTDM2InBandPEERLPStartPatten | 1.3.6.1.4.1.868.2.5.3.1.2.10.1.10 | DisplayString | RW | |
column · DisplayString · read-write · current This binary string is used to set the PEER interface In-band Loopback start Patten, such as 11000 string | ||||
| CtnIfTDM2InBandPEERLPStopPatten | 1.3.6.1.4.1.868.2.5.3.1.2.10.1.11 | DisplayString | RW | |
column · DisplayString · read-write · current This binary string is used to set the PEER interface In-band Loopback stop Patten, such as 11100 string | ||||
| CtnIfTDM2InBandLPTimeoutEnable | 1.3.6.1.4.1.868.2.5.3.1.2.10.1.12 | INTEGER | RW | |
column · INTEGER · read-write · current This variable indicates whether the In-band Loopback timeout watchdog is enabled
| ||||
| CtnIfTDM2InBandLPTimeoutCount | 1.3.6.1.4.1.868.2.5.3.1.2.10.1.13 | INTEGER (1..4095) | RW | |
column · INTEGER (1..4095) · read-write · current This variable is used to set the In-band Loopback timeout watchdog value, the unit is minute | ||||
| CtnIfTDM2InBandPEERLPTimeoutEnable | 1.3.6.1.4.1.868.2.5.3.1.2.10.1.14 | INTEGER | RW | |
column · INTEGER · read-write · current This variable indicates whether the Peer In-band Loopback timeout watchdog is enabled
| ||||
| CtnIfTDM2InBandPEERLPTimeoutCount | 1.3.6.1.4.1.868.2.5.3.1.2.10.1.15 | INTEGER (1..4095) | RW | |
column · INTEGER (1..4095) · read-write · current This variable is used to set the Peer In-band Loopback timeout watchdog value, the unit is minute | ||||
Traps / Notifications
- tnIfTDMAlarmIndicationSignalEvt
1.3.6.1.4.1.868.2.5.3.0.6