TERRA-DEFINITIONS-MIB
Terrasnmptranslate -m TERRA-DEFINITIONS-MIB -Tpsnmpwalk -v2c -c <community> -m TERRA-DEFINITIONS-MIB <host> 1.3.6.1.4.1.30631.3Imports
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP |
|---|---|
| SNMPv2-SMI | Bits, Gauge32, Integer32, IpAddress, MODULE-IDENTITY, MibIdentifier, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, iso |
| SNMPv2-TC | DisplayString, PhysAddress, TEXTUAL-CONVENTION |
| TERRA-SMI | terraRoot |
OID tree
| Name | OID | Type | Access | Status |
|---|---|---|---|---|
| IterraDefIdentMib | 1.3.6.1.4.1.30631.3 |
Textual conventions
DefFaultStatusINTEGERfault(2)normal(1)An enumerated value that provides a fault status of a particular hardware or software parameter that usually represent some sort of condition. A value normal(1) indicates the normal condition. A value fault(2) indicates the fault condition.
DefHundredthNanoMeterUnsigned32Display hint:
d-2This data type represents wavelength values that are normally expressed in nano meters. Units are in hundredths of a NanoMeter; for example, 1550.56 nm will be represented as 155056.
DefMilliAmpGauge32Display hint:
d-3This data type represents current levels that are normally expressed in amperes. Units are in milliamperes; for example, 2.1 Amperes would be expressed as 2100.
DefOnOffControlINTEGERmeaningless(3)off(1)on(2)An enumerated value that provides a control of a particular hardware or software parameter that usually represent some sort of switch. A SET request with a value off(1) will cause the switch to be shut off. A SET request with a value on(2) will cause the switch to be turned on. A value meaningless(3) will be implemented by the variables that represent a switch with write-only access. A GET request for the value of the write-only variable shall return a value meaningless(3). A SET request with a value meaningless(3) for the variable with write access shall have no effect and no exception is generated. A value may be used by the variables with both read-write and write-only access.
DefOnOffStatusINTEGERoff(1)on(2)An enumerated value that provides a status of a particular hardware or software parameter that usually represent some sort of switch. A value off(1) indicates the switch is off. A value on(2) indicates the switch is on.
DefRelayStateINTEGER (0..1)Represents relay contact state. A value closed (0) defines closed contact state, value opened (1) - opened state.
DefStatusINTEGER (0..1)This data type represents base device status (error) bits ( 0 represents normal condition, 1 - represents fault condition).
DefTenthAmpGauge32Display hint:
d-1This data type represents current levels that are normally expressed in Amperes. Units are in tenths of a Ampere; for example, 1.1 Amperes will be represented as 11.
DefTenthCentigradeGauge32Display hint:
d-1This data type represents temperature values that are normally expressed in Centigrade. Units are in tenths of a Centigrade; for example, -5.1 Centigrade will be represented as -51.
DefTenthVoltGauge32Display hint:
d-1This data type represents voltage levels that are normally expressed in volts. Units are in tenths of a volt; for example, -48.1 volts will be represented as -481.
DefTenthdBInteger32 (-100..200)Display hint:
d-1This data type represents power levels that are normally expressed in dB. Units are in tenths of a dB; for example, -5.1 dB will be represented as -51.
DefTenthdBmInteger32 (-100..200)Display hint:
d-1This data type represents power levels that are normally expressed in dBm. Units are in tenths of a dBm; for example, -5.1 dBm will be represented as -51.
DefTenthdBuVInteger32 (-100..200)Display hint:
d-1This data type represents power levels that are normally expressed in dBmV. Units are in tenths of a dBmV; for example, -5.1 dBmV will be represented as -51.