PRVT-MPLS-TE-MIB
B.A.T.M. Advance TechnologiesThis MIB module contains managed object definitions for MPLS Traffic Engineering (TE) as defined in: Extensions to RSVP for LSP Tunnels, Awduche et al, Internet Draft <draft-ietf-mpls-rsvp-lsp-tunnel- 07.txt>, August 2000; Constraint-Based LSP Setup using LDP, B. Jamoussi, Internet Draft <draft-ietf- mpls-cr-ldp-04.txt>, July 2000; Requirements for Traffic Engineering Over MPLS, Awduche, D., J. Malcolm, J., Agogbua, J., O'Dell, M., J. McManus, <rfc2702.txt>, September 1999.
snmptranslate -m PRVT-MPLS-TE-MIB -Tpsnmpwalk -v2c -c <community> -m PRVT-MPLS-TE-MIB <host> 1.3.6.1.4.1.738.10.6.3.2Imports
| PRVT-SWITCH-MIB | mpls |
|---|---|
| PRVT-TEMIB-ENTITY-MIB | prvtMplsTeMibEntityIndex |
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP |
| SNMPv2-SMI | Bits, Integer32, IpAddress, MODULE-IDENTITY, MibIdentifier, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, iso |
| SNMPv2-TC | DisplayString, PhysAddress, RowStatus, TEXTUAL-CONVENTION, TruthValue |
OID tree
| Name | OID | Type | Access | Status |
|---|---|---|---|---|
| IprvtMplsTeMIB | 1.3.6.1.4.1.738.10.6.3.2 | |||
identity This MIB module contains managed object definitions for MPLS Traffic Engineering (TE) as defined in: Extensions to RSVP for LSP Tunnels, Awduche et al, Internet Draft <draft-ietf-mpls-rsvp-lsp-tunnel- 07.txt>, August 2000; Constraint-Based LSP Setup using LDP, B. Jamoussi, Internet Draft <draft-ietf- mpls-cr-ldp-04.txt>, July 2000; Requirements for Traffic Engineering Over MPLS, Awduche, D., J. Malcolm, J., Agogbua, J., O'Dell, M., J. McManus, <rfc2702.txt>, September 1999. | ||||
| NmplsTeNotifications | 1.3.6.1.4.1.738.10.6.3.2.0 | |||
| !mplsManTunnelUp | 1.3.6.1.4.1.738.10.6.3.2.0.1 | |||
notification · current This notification is generated when a mplsManTunnelOperStatus object for one of the configured tunnels is about to leave the down state and transition into some other state (but not into the notPresent state). This other state is indicated by the included value of mplsManTunnelOperStatus. This structure is the same as the generic AMB_MPLS_TUNNEL_TRAP_COMMON. | ||||
| !mplsManTunnelDown | 1.3.6.1.4.1.738.10.6.3.2.0.2 | |||
notification · current This notification is generated when a mplsManTunnelOperStatus object for one of the configured tunnels is about to enter the down state from some other state (but not from the notPresent state). This other state is indicated by the included value of mplsManTunnelOperStatus. This structure is the same as the generic AMB_MPLS_TUNNEL_TRAP_COMMON. | ||||
| !mplsAutoTunnelUp | 1.3.6.1.4.1.738.10.6.3.2.0.3 | |||
notification · current This notification is generated when a mplsAutoTunnelOperStatus object for one of the configured tunnels is about to leave the down state and transition into some other state (but not into the notPresent state). This other state is indicated by the included value of mplsAutoTunnelOperStatus. This structure is the same as the generic AMB_MPLS_TUNNEL_TRAP_COMMON. | ||||
| !mplsAutoTunnelDown | 1.3.6.1.4.1.738.10.6.3.2.0.4 | |||
notification · current This notification is generated when a mplsAutoTunnelOperStatus object for one of the configured tunnels is about to enter the down state from some other state (but not from the notPresent state). This other state is indicated by the included value of mplsAutoTunnelOperStatus. This structure is the same as the generic AMB_MPLS_TUNNEL_TRAP_COMMON. | ||||
| !mplsDynTunnelUp | 1.3.6.1.4.1.738.10.6.3.2.0.5 | |||
notification · current This notification is generated when a mplsDynTunnelOperStatus object for one of the configured tunnels is about to leave the down state and transition into some other state (but not into the notPresent state). This other state is indicated by the included value of mplsDynTunnelOperStatus. This structure is the same as the generic AMB_MPLS_TUNNEL_TRAP_COMMON. | ||||
| !mplsDynTunnelDown | 1.3.6.1.4.1.738.10.6.3.2.0.6 | |||
notification · current This notification is generated when a mplsDynTunnelOperStatus object for one of the configured tunnels is about to enter the down state from some other state (but not from the notPresent state). This other state is indicated by the included value of mplsDynTunnelOperStatus. This structure is the same as the generic AMB_MPLS_TUNNEL_TRAP_COMMON. | ||||
| !mplsManTunnelReoptimized | 1.3.6.1.4.1.738.10.6.3.2.0.7 | |||
notification · current This notification is generated when a tunnel is reoptimized. If the mplsTunnelARHopTable is used, then this tunnel instance's entry in the mplsTunnelARHopTable MAY contain the new path for this tunnel some time after this trap is issued by the agent. This structure is the same as the generic AMB_MPLS_TUNNEL_TRAP_COMMON. | ||||
| NmplsTeObjects | 1.3.6.1.4.1.738.10.6.3.2.1 | |||
| SmplsTeObjectReserved1 | 1.3.6.1.4.1.738.10.6.3.2.1.1 | MplsTeObjectReservedTC | RW | |
scalar · MplsTeObjectReservedTC · read-write · current This object is reserved for future use. | ||||
| TmplsManTunnelTable | 1.3.6.1.4.1.738.10.6.3.2.1.2 | NA | ||
table · not-accessible · current The mplsManTunnelTable allows new MPLS tunnels to be created between an LSR and a remote endpoint, and existing tunnels to be reconfigured or removed. Note that only point-to-point tunnel segments are supported, although multi-point-to-point and point- to-multi-point connections are supported by an LSR acting as a cross-connect. Each MPLS tunnel can thus have one out-segment originating at this LSR and/or one in-segment terminating at this LSR. To configure tunnels where the ingress and egress routers are identified by IPv6 addresses, the following approach is used. - The mplsManTunnelIngressLSRId and mplsManTunnelEgressLSRId fields are set to 32-bit identifiers for the ingress and egress routers. - mplsManTunnelHopTableIndex must be set to a non-zero value. - The first hop in the hop table for the tunnel path must be set to a global scope IPv6 address of the local router. - The last entry in the hop table must be set to a global scope IPv6 address of the egress router. | ||||
| RmplsManTunnelEntry | 1.3.6.1.4.1.738.10.6.3.2.1.2.1 | NA | ||
row · not-accessible · current An entry in this table represents an MPLS tunnel. An entry can be created by a network administrator or by an SNMP agent as instructed by an MPLS signaling protocol. Whenever a new entry is created with mplsManTunnelIsIf set to true(1), then a corresponding entry is created in ifTable as well (see RFC 2233). The ifType of this entry is mplsTunnel(150). | ||||
| CmplsManTunnelIndex | 1.3.6.1.4.1.738.10.6.3.2.1.2.1.1 | Integer32 (1..32638) | NA | |
column · Integer32 (1..32638) · not-accessible · current Uniquely identifies this row. | ||||
| CmplsManTunnelInstance | 1.3.6.1.4.1.738.10.6.3.2.1.2.1.2 | MplsTunnelInstanceIndex | NA | |
column · MplsTunnelInstanceIndex · not-accessible · current Uniquely identifies an instance of a tunnel. It is useful to identify multiple instances of tunnels for the purposes of backup and parallel tunnels. | ||||
| CmplsManTunnelRowStatus | 1.3.6.1.4.1.738.10.6.3.2.1.2.1.3 | RowStatus | RC | |
column · RowStatus · read-create · current This variable is used to create, modify, and/or delete a row in this table. When a row in this table is in active(1) state, no objects in that row can be modified by the agent except mplsManTunnelAdminStatus, mplsManTunnelRowStatus and mplsManTunnelStorageType. | ||||
| CmplsManTunnelIngressLSRId | 1.3.6.1.4.1.738.10.6.3.2.1.2.1.4 | MplsExtendedTunnelIdOctetType | RC | |
column · MplsExtendedTunnelIdOctetType · read-create · current Identity of the ingress LSR associated with this tunnel instance. When the MPLS signalling protocol is rsvp(2) this value SHOULD be equal to the Tunnel Sender Address in the Sender Template object and MAY be equal to the Extended Tunnel Id field in the SESSION object. When the MPLS signalling protocol is crldp(3) this value SHOULD be equal to the Ingress LSR Router ID field in the LSPID TLV object. | ||||
| CmplsManTunnelEgressLSRId | 1.3.6.1.4.1.738.10.6.3.2.1.2.1.5 | MplsExtendedTunnelIdOctetType | RC | |
column · MplsExtendedTunnelIdOctetType · read-create · current Identity of the egress LSR associated with this tunnel instance. | ||||
| CmplsManTunnelName | 1.3.6.1.4.1.738.10.6.3.2.1.2.1.6 | OCTET STRING (SIZE (1..32)) | RC | |
column · OCTET STRING (SIZE (1..32)) · read-create · current The canonical name assigned to the tunnel. This name can be used to refer to the tunnel on the LSRs console port. Also see the description of ifName in RFC 2863. | ||||
| CmplsManTunnelDescr | 1.3.6.1.4.1.738.10.6.3.2.1.2.1.7 | OCTET STRING (SIZE (0..32)) | RC | |
column · OCTET STRING (SIZE (0..32)) · read-create · current A textual string containing information about the tunnel. If there is no description this object contains a zero length string. This object may not be signaled by MPLS signaling protocols, consequentally the value of this object at transit and egress LSRs MAY be automatically generated or absent. | ||||
| CmplsManTunnelIfIndex | 1.3.6.1.4.1.738.10.6.3.2.1.2.1.8 | MplsTunnelInterfaceIndexOrZero | RO | |
column · MplsTunnelInterfaceIndexOrZero · read-only · current If mplsManTunnelIsIf is set to true, then this value contains the LSR-assigned ifIndex which corresponds to an entry in the interfaces table. Otherwise this variable should contain the value of zero indicating that a valid ifIndex was not assigned to this tunnel interface. | ||||
| CmplsManTunnelSetupPrio | 1.3.6.1.4.1.738.10.6.3.2.1.2.1.9 | Integer32 (0..7) | RC | |
column · Integer32 (0..7) · read-create · current Indicates the setup priority of this tunnel. | ||||
| CmplsManTunnelHoldingPrio | 1.3.6.1.4.1.738.10.6.3.2.1.2.1.10 | Integer32 (0..7) | RC | |
column · Integer32 (0..7) · read-create · current Indicates the holding priority for this tunnel. | ||||
| CmplsManTunnelSessionAttributes | 1.3.6.1.4.1.738.10.6.3.2.1.2.1.11 | Bits | RC | |
column · Bits · read-create · current This bitmask indicates optional session values for this tunnel. The following describes these bit fields: fastReroute This flag indicates that any tunnel hop may choose to reroute this tunnel without tearing it down. This flag permits transit routers to use a local repair mechanism which may result in violation of the explicit routing of this tunnel. When a fault is detected on an adjacent downstream link or node, a transit router can reroute traffic for fast service restoration. mergingPermitted This flag permits transit routers to merge this session with other RSVP sessions for the purpose of reducing resource overhead on downstream transit routers, thereby providing better network scalability. isPersistent Indicates whether this tunnel should be restored automatically after a failure occurs. isPinned This flag indicates whether the loose- routed hops of this tunnel are to be pinned. recordRoute This flag indicates if the signaling protocol should remember the tunnel path after it has been signaled. -- recordLabels This flag indicates if the -- signaling protocol should record labels as well as -- the tunnel path. bandwidthProtect This flag indicates whether fast reroute bandwidth protection is desired. nodeProtect This flag indicates whether fast reroute node protection is desired.
| ||||
| CmplsManTunnelLocalProtectInUse | 1.3.6.1.4.1.738.10.6.3.2.1.2.1.12 | TruthValue | RO | |
column · TruthValue · read-only · current Indicates that the local repair mechanism is in use to maintain this tunnel (usually in the face of an outage of the link it was previously routed over). | ||||
| CmplsManTunnelHopTableIndex | 1.3.6.1.4.1.738.10.6.3.2.1.2.1.13 | MplsPathIndexOrZero | RC | |
column · MplsPathIndexOrZero · read-create · current Index into the mplsTunnelManHopTable entry that specifies the explicit route hops for this tunnel. This object is meaningful only at the head-end of the tunnel. For UNI tunnels, this field should be set to 0. For tunnels with no configured explicit route hops, this field should be set to 0. In this case, the tunnel is routed using mplsTunnelEgressLSRId. | ||||
| CmplsManTunnelPathInUse | 1.3.6.1.4.1.738.10.6.3.2.1.2.1.14 | MplsPathIndexOrZero | RC | |
column · MplsPathIndexOrZero · read-create · current This value denotes the configured path that was chosen for this tunnel. This value reflects the secondary index into mplsTunnelManHopTable. This path may not exactly match the one in mplsTunnelARHopTable due to the fact that some CSPF modification may have taken place. See mplsTunnelARHopTable for the actual path being taken by the tunnel. A value of zero denotes that no path is currently in use or available. For UNI tunnels, this field should be set to 0. For tunnels with no configued explicit route hops, this field should be set to 0. | ||||
| CmplsManTunnelIncludeAnyAffinity | 1.3.6.1.4.1.738.10.6.3.2.1.2.1.15 | MplsTunnelAffinity | RC | |
column · MplsTunnelAffinity · read-create · current A link satisfies the include-any constraint if and only if the constraint is zero, or the link and the constraint have a resource class in common. The field is a bitmask. Every request does not overwrite the previous one. 0 value resets the field. | ||||
| CmplsManTunnelIncludeAllAffinity | 1.3.6.1.4.1.738.10.6.3.2.1.2.1.16 | MplsTunnelAffinity | RC | |
column · MplsTunnelAffinity · read-create · current A link satisfies the include-all constraint if and only if the link contains all of the administrative groups specified in the constraint. The field is a bitmask. Every request does not overwrite the previous one. 0 value resets the field. | ||||
| CmplsManTunnelExcludeAnyAffinity | 1.3.6.1.4.1.738.10.6.3.2.1.2.1.17 | MplsTunnelAffinity | RC | |
column · MplsTunnelAffinity · read-create · current A link satisfies the exclude-any constraint if and only if the link contains none of the administrative groups specified in the constraint. The field is a bitmask. Every request does not overwrite the previous one. 0 value resets the field. | ||||
| CmplsManTunnelAdminStatus | 1.3.6.1.4.1.738.10.6.3.2.1.2.1.18 | INTEGER | RC | |
column · INTEGER · read-create · current Indicates the desired operational status of this tunnel.
| ||||
| CmplsManTunnelOperStatus | 1.3.6.1.4.1.738.10.6.3.2.1.2.1.19 | INTEGER | RO | |
column · INTEGER · read-only · current Indicates the actual operational status of this tunnel, which is typically but not limited to, a function of the state of individual segments of this tunnel.
| ||||
| CmplsManTunnelAttributes | 1.3.6.1.4.1.738.10.6.3.2.1.2.1.20 | Bits | RC | |
column · Bits · read-create · current This bitmask indicates optional parameters for this tunnel. These bits should be taken in addition to those defined in mplsManTunnelSessionAttributes in order to determine the full set of options to be signaled (for example SESSION_ATTRIBUTES flags in RSVP-TE). The following describes these bitfields: labelRecordingDesired This flag indicates that label information should be included when doing a route record. This bit is not valid unless the recordRoute bit is set in the mplsManTunnelSessionAttributes object.
| ||||
| CmplsManTunnelPathComp | 1.3.6.1.4.1.738.10.6.3.2.1.2.1.21 | INTEGER | RC | |
column · INTEGER · read-create · current This value instructs the source node on how to perform path computation on the explicit route specified by the associated entries in the mplsTunnelManHopTable. dynamicFull The user specifies at least the source and destination of the path and expects that the CSPF will calculate the remainder of the path. explicit The user specifies the entire path for the tunnel to take. This path may contain strict or loose hops. Evaluation of the explicit route will be performed hop by hop through the network. dynamicPartial The user specifies at least the source and destination of the path and expects that the CSPF will calculate the remainder of the path. The path computed by CSPF is allowed to be only partially computed allowing the remainder of the path to be filled in across the network. This object deprecates mplsTunnelManHopEntryPathComp.
| ||||
| CmplsManTunnelFastRerouteMode | 1.3.6.1.4.1.738.10.6.3.2.1.2.1.22 | INTEGER | RC | |
column · INTEGER · read-create · current Indicates whether or not this tunnel should be protected by a fast reroute mechanism, and if so which method should be used. noFastReroute - no fast reroute protection. detourFastReroute - fast reroute protection using the one-to-one detour backup method. facilityFastReroute - fast reroute protection using the facility backup method. Fast reroute is only available for uni-directional LSPs.
| ||||
| CmplsManTunnelBackupSetupPrio | 1.3.6.1.4.1.738.10.6.3.2.1.2.1.23 | Integer32 (0..7) | RC | |
column · Integer32 (0..7) · read-create · current Setup priority for backup tunnels set up to protect this tunnel. This field is only valid if the mplsManTunnelFastRerouteMode above is not noFastReroute. | ||||
| CmplsManTunnelBackupHoldingPrio | 1.3.6.1.4.1.738.10.6.3.2.1.2.1.24 | Integer32 (0..7) | RC | |
column · Integer32 (0..7) · read-create · current Holding priority for backup tunnels set up to protect this tunnel. This field is only valid if the mplsManTunnelFastRerouteMode above is not noFastReroute. | ||||
| CmplsManTunnelBackupIncAny | 1.3.6.1.4.1.738.10.6.3.2.1.2.1.25 | MplsTunnelAffinity | RC | |
column · MplsTunnelAffinity · read-create · current Include-any resource affinity for backup tunnels set up to protect this tunnel. A link satisfies the include-any constraint if and only if the constraint is zero, or the link and the constraint have a resource class in common. This field is only valid if the mplsManTunnelFastRerouteMode above is not noFastReroute. | ||||
| CmplsManTunnelBackupIncAll | 1.3.6.1.4.1.738.10.6.3.2.1.2.1.26 | MplsTunnelAffinity | RC | |
column · MplsTunnelAffinity · read-create · current Include-all resource affinity for backup tunnels set up to protect this tunnel. A link satisfies the include-all constraint if and only if the link contains all of the adminstrative groups specified in the constraint. This field is only valid if the mplsManTunnelFastRerouteMode above is not noFastReroute. | ||||
| CmplsManTunnelBackupExcAny | 1.3.6.1.4.1.738.10.6.3.2.1.2.1.27 | MplsTunnelAffinity | RC | |
column · MplsTunnelAffinity · read-create · current Exclude-any resource affinity for backup tunnels set up to protect this tunnel. A link satisfies the exclude-any constraint if and only if the constraint is zero, or the link and the constraint have a resource class in common. This field is only valid if the mplsManTunnelFastRerouteMode above is not noFastReroute. | ||||
| CmplsManTunnelBackupBandwidth | 1.3.6.1.4.1.738.10.6.3.2.1.2.1.28 | MplsBitRate | RC | |
column · MplsBitRate · read-create · current The estimated bandwidth required for backup tunnels, in units of 1000 bits/second. A value of zero indicates best-effort. This field is only valid if the mplsManTunnelFastRerouteMode above is not noFastReroute.
| ||||
| CmplsManTunnelBackupMaxHops | 1.3.6.1.4.1.738.10.6.3.2.1.2.1.29 | Unsigned32 (1..4294967295) | RC | |
column · Unsigned32 (1..4294967295) · read-create · current The maximum number of extra hops the backup path is allowed to take, from a Point of Local Repair (PLR) to a Merge Point (MP), with PLR and MP excluded in counting. A hop-limit of 0 means only direct links between PLR and MP can be used. This field is only valid if the mplsManTunnelFastRerouteMode above is not noFastReroute. | ||||
| CmplsManTunnelMtu | 1.3.6.1.4.1.738.10.6.3.2.1.2.1.30 | Integer32 (64..12288) | RC | |
column · Integer32 (64..12288) · read-create · current Maximal transfer unit of the tunnel | ||||
| CmplsManTunnelRebuildTimer | 1.3.6.1.4.1.738.10.6.3.2.1.2.1.31 | Unsigned32 | RC | |
column · Unsigned32 · read-create · current Defines a period in minutes (0..1440), after which the tunnel will be unconditionally rebuild. The maximal valid value is 1440 minutes (24 hours) | ||||
| CmplsManTunnelOperStatusFlags | 1.3.6.1.4.1.738.10.6.3.2.1.2.1.32 | Bits | RO | |
column · Bits · read-only · current Flags to extend the information of the tunnel state For the behaviour - bits meaning: tunnelResignalling (1) - This status shows that currently the tunnel has been resignalled. The resignalling state of a tunnel should be considered together with the mplsManTunnelOperStatus attribute value of the same tunnel. tunnelSuppressed (2) - This status shows that the tunnel has been established, but a higher priority tunnel is active and in use. This tunnel can be activated, once the higher protocol tunnel fails by any reason, and in this case the tunnelSuppressed status will be cleared.
| ||||
| CmplsManTunnelGuardedDest | 1.3.6.1.4.1.738.10.6.3.2.1.2.1.33 | IpAddress | RC | |
column · IpAddress · read-create · current The guarded destination object specifies which IP destination address the current tunnel protects used with the fast reroute feature. The tunnel must not be fast reroute enabled. | ||||
| CmplsManTunnelMBBTimeOut | 1.3.6.1.4.1.738.10.6.3.2.1.2.1.34 | Integer32 | RC | |
column · Integer32 · read-create · current Specifies the timer configuration (in minutes) for Make-before-break (MBB). The default value of this object is 10 minutes. | ||||
| CmplsManTunnelOwner | 1.3.6.1.4.1.738.10.6.3.2.1.2.1.35 | MplsOwner | RO | |
column · MplsOwner · read-only · current Denotes the entity that created and is responsible for managing this tunnel. This column is automatically filled by the agent on creation of a row. | ||||
| CmplsManTunnelARHopTableIndex | 1.3.6.1.4.1.738.10.6.3.2.1.2.1.36 | MplsPathIndexOrZero | RO | |
column · MplsPathIndexOrZero · read-only · current Index into the mplsTunnelARHopTable entry that specifies the actual hops traversed by the tunnel. This is automatically updated by the agent when the actual hops becomes available. | ||||
| CmplsManTunnelCHopTableIndex | 1.3.6.1.4.1.738.10.6.3.2.1.2.1.37 | MplsPathIndexOrZero | RO | |
column · MplsPathIndexOrZero · read-only · current Index into the mplsTunnelCHopTable entry that specifies the computed hops traversed by the tunnel. This is automatically updated by the agent when computed hops become available or when computed hops get modified. | ||||
| SmplsTeObjectReserved3 | 1.3.6.1.4.1.738.10.6.3.2.1.3 | MplsTeObjectReservedTC | RW | |
scalar · MplsTeObjectReservedTC · read-write · current This object is reserved for future use. | ||||
| TmplsAutoTunnelTable | 1.3.6.1.4.1.738.10.6.3.2.1.4 | NA | ||
table · not-accessible · current Similar to mplsManTunnelTable but for automatic tunnels. | ||||
| RmplsAutoTunnelEntry | 1.3.6.1.4.1.738.10.6.3.2.1.4.1 | NA | ||
row · not-accessible · current See similar object in mplsManTunnelTable. | ||||
| CmplsAutoTunnelIndex | 1.3.6.1.4.1.738.10.6.3.2.1.4.1.1 | Integer32 (32639..32767) | NA | |
column · Integer32 (32639..32767) · not-accessible · current See similar object in mplsManTunnelTable. | ||||
| CmplsAutoTunnelInstance | 1.3.6.1.4.1.738.10.6.3.2.1.4.1.2 | MplsTunnelInstanceIndex | NA | |
column · MplsTunnelInstanceIndex · not-accessible · current See similar object in mplsManTunnelTable. | ||||
| CmplsAutoTunnelRowStatus | 1.3.6.1.4.1.738.10.6.3.2.1.4.1.3 | RowStatus | RC | |
column · RowStatus · read-create · current See similar object in mplsManTunnelTable. | ||||
| CmplsAutoTunnelIngressLSRId | 1.3.6.1.4.1.738.10.6.3.2.1.4.1.4 | MplsExtendedTunnelIdOctetType | RO | |
column · MplsExtendedTunnelIdOctetType · read-only · current See similar object in mplsManTunnelTable. | ||||
| CmplsAutoTunnelEgressLSRId | 1.3.6.1.4.1.738.10.6.3.2.1.4.1.5 | MplsExtendedTunnelIdOctetType | RO | |
column · MplsExtendedTunnelIdOctetType · read-only · current See similar object in mplsManTunnelTable. | ||||
| CmplsAutoTunnelName | 1.3.6.1.4.1.738.10.6.3.2.1.4.1.6 | OCTET STRING (SIZE (1..32)) | RO | |
column · OCTET STRING (SIZE (1..32)) · read-only · current See similar object in mplsManTunnelTable. | ||||
| CmplsAutoTunnelDescr | 1.3.6.1.4.1.738.10.6.3.2.1.4.1.7 | OCTET STRING (SIZE (0..32)) | RO | |
column · OCTET STRING (SIZE (0..32)) · read-only · current See similar object in mplsManTunnelTable. | ||||
| CmplsAutoTunnelIfIndex | 1.3.6.1.4.1.738.10.6.3.2.1.4.1.8 | MplsTunnelInterfaceIndexOrZero | RO | |
column · MplsTunnelInterfaceIndexOrZero · read-only · current See similar object in mplsManTunnelTable. | ||||
| CmplsAutoTunnelSetupPrio | 1.3.6.1.4.1.738.10.6.3.2.1.4.1.9 | Integer32 (0..7) | RO | |
column · Integer32 (0..7) · read-only · current See similar object in mplsManTunnelTable. | ||||
| CmplsAutoTunnelHoldingPrio | 1.3.6.1.4.1.738.10.6.3.2.1.4.1.10 | Integer32 (0..7) | RO | |
column · Integer32 (0..7) · read-only · current See similar object in mplsManTunnelTable. | ||||
| CmplsAutoTunnelSessionAttributes | 1.3.6.1.4.1.738.10.6.3.2.1.4.1.11 | Bits | RO | |
column · Bits · read-only · current See similar object in mplsManTunnelTable.
| ||||
| CmplsAutoTunnelLocalProtectInUse | 1.3.6.1.4.1.738.10.6.3.2.1.4.1.12 | TruthValue | RO | |
column · TruthValue · read-only · current See similar object in mplsManTunnelTable. | ||||
| CmplsAutoTunnelHopTableIndex | 1.3.6.1.4.1.738.10.6.3.2.1.4.1.14 | MplsPathIndexOrZero | RO | |
column · MplsPathIndexOrZero · read-only · current See similar object in mplsManTunnelTable. | ||||
| CmplsAutoTunnelPathInUse | 1.3.6.1.4.1.738.10.6.3.2.1.4.1.15 | MplsPathIndexOrZero | RO | |
column · MplsPathIndexOrZero · read-only · current See similar object in mplsManTunnelTable. | ||||
| CmplsAutoTunnelIncludeAnyAffinity | 1.3.6.1.4.1.738.10.6.3.2.1.4.1.16 | MplsTunnelAffinity | RO | |
column · MplsTunnelAffinity · read-only · current See similar object in mplsManTunnelTable. | ||||
| CmplsAutoTunnelIncludeAllAffinity | 1.3.6.1.4.1.738.10.6.3.2.1.4.1.17 | MplsTunnelAffinity | RO | |
column · MplsTunnelAffinity · read-only · current See similar object in mplsManTunnelTable. | ||||
| CmplsAutoTunnelExcludeAnyAffinity | 1.3.6.1.4.1.738.10.6.3.2.1.4.1.18 | MplsTunnelAffinity | RO | |
column · MplsTunnelAffinity · read-only · current See similar object in mplsManTunnelTable. | ||||
| CmplsAutoTunnelOperStatus | 1.3.6.1.4.1.738.10.6.3.2.1.4.1.19 | INTEGER | RO | |
column · INTEGER · read-only · current See similar object in mplsManTunnelTable.
| ||||
| CmplsAutoTunnelAttributes | 1.3.6.1.4.1.738.10.6.3.2.1.4.1.20 | Bits | RO | |
column · Bits · read-only · current See similar object in mplsManTunnelTable.
| ||||
| CmplsAutoTunnelPathComp | 1.3.6.1.4.1.738.10.6.3.2.1.4.1.21 | INTEGER | RO | |
column · INTEGER · read-only · current See similar object in mplsManTunnelTable.
| ||||
| CmplsAutoTunnelFastRerouteMode | 1.3.6.1.4.1.738.10.6.3.2.1.4.1.22 | INTEGER | RO | |
column · INTEGER · read-only · current See similar object in mplsManTunnelTable.
| ||||
| CmplsAutoTunnelBackupSetupPrio | 1.3.6.1.4.1.738.10.6.3.2.1.4.1.23 | Integer32 (0..7) | RO | |
column · Integer32 (0..7) · read-only · current See similar object in mplsManTunnelTable. | ||||
| CmplsAutoTunnelBackupHoldingPrio | 1.3.6.1.4.1.738.10.6.3.2.1.4.1.24 | Integer32 (0..7) | RO | |
column · Integer32 (0..7) · read-only · current See similar object in mplsManTunnelTable. | ||||
| CmplsAutoTunnelBackupIncAny | 1.3.6.1.4.1.738.10.6.3.2.1.4.1.25 | MplsTunnelAffinity | RO | |
column · MplsTunnelAffinity · read-only · current See similar object in mplsManTunnelTable. | ||||
| CmplsAutoTunnelBackupIncAll | 1.3.6.1.4.1.738.10.6.3.2.1.4.1.26 | MplsTunnelAffinity | RO | |
column · MplsTunnelAffinity · read-only · current See similar object in mplsManTunnelTable. | ||||
| CmplsAutoTunnelBackupExcAny | 1.3.6.1.4.1.738.10.6.3.2.1.4.1.27 | MplsTunnelAffinity | RO | |
column · MplsTunnelAffinity · read-only · current See similar object in mplsManTunnelTable. | ||||
| CmplsAutoTunnelBackupBandwidth | 1.3.6.1.4.1.738.10.6.3.2.1.4.1.28 | MplsBitRate | RO | |
column · MplsBitRate · read-only · current See similar object in mplsManTunnelTable.
| ||||
| CmplsAutoTunnelBackupMaxHops | 1.3.6.1.4.1.738.10.6.3.2.1.4.1.29 | Unsigned32 (1..4294967295) | RO | |
column · Unsigned32 (1..4294967295) · read-only · current See similar object in mplsManTunnelTable. | ||||
| CmplsAutoTunnelMtu | 1.3.6.1.4.1.738.10.6.3.2.1.4.1.30 | Integer32 | RO | |
column · Integer32 · read-only · current See similar object in mplsManTunnelTable. | ||||
| CmplsAutoTunnelRebuildTimer | 1.3.6.1.4.1.738.10.6.3.2.1.4.1.31 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current The period, in seconds, after which the tunnel will be rebuilt. | ||||
| CmplsAutoTunnelOperStatusFlags | 1.3.6.1.4.1.738.10.6.3.2.1.4.1.32 | Bits | RO | |
column · Bits · read-only · current See similar object in mplsManTunnelTable.
| ||||
| CmplsAutoTunnelGuardedDest | 1.3.6.1.4.1.738.10.6.3.2.1.4.1.33 | IpAddress | RO | |
column · IpAddress · read-only · current See similar object in mplsManTunnelTable. | ||||
| CmplsAutoTunnelMBBTimeOut | 1.3.6.1.4.1.738.10.6.3.2.1.4.1.34 | Integer32 | RO | |
column · Integer32 · read-only · current See similar object in mplsManTunnelTable. | ||||
| CmplsAutoTunnelOwner | 1.3.6.1.4.1.738.10.6.3.2.1.4.1.35 | MplsOwner | RO | |
column · MplsOwner · read-only · current See similar object in mplsManTunnelTable. | ||||
| CmplsAutoTunnelARHopTableIndex | 1.3.6.1.4.1.738.10.6.3.2.1.4.1.36 | MplsPathIndexOrZero | RO | |
column · MplsPathIndexOrZero · read-only · current See similar object in mplsManTunnelTable. | ||||
| CmplsAutoTunnelCHopTableIndex | 1.3.6.1.4.1.738.10.6.3.2.1.4.1.37 | MplsPathIndexOrZero | RO | |
column · MplsPathIndexOrZero · read-only · current See similar object in mplsManTunnelTable. | ||||
| SmplsTeObjectReserved5 | 1.3.6.1.4.1.738.10.6.3.2.1.5 | MplsTeObjectReservedTC | RW | |
scalar · MplsTeObjectReservedTC · read-write · current This object is reserved for future use. | ||||
| TmplsDynTunnelTable | 1.3.6.1.4.1.738.10.6.3.2.1.6 | NA | ||
table · not-accessible · current Similar to mplsManTunnelTable but for dynamic tunnels. | ||||
| RmplsDynTunnelEntry | 1.3.6.1.4.1.738.10.6.3.2.1.6.1 | NA | ||
row · not-accessible · current See similar object in mplsManTunnelTable. | ||||
| CmplsDynTunnelIndex | 1.3.6.1.4.1.738.10.6.3.2.1.6.1.1 | Integer32 (32768..65535) | NA | |
column · Integer32 (32768..65535) · not-accessible · current See similar object in mplsManTunnelTable. | ||||
| CmplsDynTunnelInstance | 1.3.6.1.4.1.738.10.6.3.2.1.6.1.2 | MplsTunnelInstanceIndex | NA | |
column · MplsTunnelInstanceIndex · not-accessible · current See similar object in mplsManTunnelTable. | ||||
| CmplsDynTunnelIngressLSRId | 1.3.6.1.4.1.738.10.6.3.2.1.6.1.3 | MplsExtendedTunnelIdOctetType | RO | |
column · MplsExtendedTunnelIdOctetType · read-only · current See similar object in mplsManTunnelTable. | ||||
| CmplsDynTunnelEgressLSRId | 1.3.6.1.4.1.738.10.6.3.2.1.6.1.4 | MplsExtendedTunnelIdOctetType | RO | |
column · MplsExtendedTunnelIdOctetType · read-only · current See similar object in mplsManTunnelTable. | ||||
| CmplsDynTunnelName | 1.3.6.1.4.1.738.10.6.3.2.1.6.1.5 | OCTET STRING (SIZE (1..32)) | RO | |
column · OCTET STRING (SIZE (1..32)) · read-only · current See similar object in mplsManTunnelTable. | ||||
| CmplsDynTunnelDescr | 1.3.6.1.4.1.738.10.6.3.2.1.6.1.6 | OCTET STRING (SIZE (0..32)) | RO | |
column · OCTET STRING (SIZE (0..32)) · read-only · current See similar object in mplsManTunnelTable. | ||||
| CmplsDynTunnelIfIndex | 1.3.6.1.4.1.738.10.6.3.2.1.6.1.7 | MplsTunnelInterfaceIndexOrZero | RO | |
column · MplsTunnelInterfaceIndexOrZero · read-only · current See similar object in mplsManTunnelTable. | ||||
| CmplsDynTunnelSetupPrio | 1.3.6.1.4.1.738.10.6.3.2.1.6.1.8 | Integer32 (0..7) | RO | |
column · Integer32 (0..7) · read-only · current See similar object in mplsManTunnelTable. | ||||
| CmplsDynTunnelHoldingPrio | 1.3.6.1.4.1.738.10.6.3.2.1.6.1.9 | Integer32 (0..7) | RO | |
column · Integer32 (0..7) · read-only · current See similar object in mplsManTunnelTable. | ||||
| CmplsDynTunnelSessionAttributes | 1.3.6.1.4.1.738.10.6.3.2.1.6.1.10 | Bits | RO | |
column · Bits · read-only · current See similar object in mplsManTunnelTable.
| ||||
| CmplsDynTunnelLocalProtectInUse | 1.3.6.1.4.1.738.10.6.3.2.1.6.1.11 | TruthValue | RO | |
column · TruthValue · read-only · current See similar object in mplsManTunnelTable. | ||||
| CmplsDynTunnelHopTableIndex | 1.3.6.1.4.1.738.10.6.3.2.1.6.1.12 | MplsPathIndexOrZero | RO | |
column · MplsPathIndexOrZero · read-only · current See similar object in mplsManTunnelTable. | ||||
| CmplsDynTunnelPathInUse | 1.3.6.1.4.1.738.10.6.3.2.1.6.1.13 | MplsPathIndexOrZero | RO | |
column · MplsPathIndexOrZero · read-only · current See similar object in mplsManTunnelTable. | ||||
| CmplsDynTunnelIncludeAnyAffinity | 1.3.6.1.4.1.738.10.6.3.2.1.6.1.14 | MplsTunnelAffinity | RO | |
column · MplsTunnelAffinity · read-only · current See similar object in mplsManTunnelTable. | ||||
| CmplsDynTunnelIncludeAllAffinity | 1.3.6.1.4.1.738.10.6.3.2.1.6.1.15 | MplsTunnelAffinity | RO | |
column · MplsTunnelAffinity · read-only · current See similar object in mplsManTunnelTable. | ||||
| CmplsDynTunnelExcludeAnyAffinity | 1.3.6.1.4.1.738.10.6.3.2.1.6.1.16 | MplsTunnelAffinity | RO | |
column · MplsTunnelAffinity · read-only · current See similar object in mplsManTunnelTable. | ||||
| CmplsDynTunnelAdminStatus | 1.3.6.1.4.1.738.10.6.3.2.1.6.1.17 | INTEGER | RO | |
column · INTEGER · read-only · current See similar object in mplsManTunnelTable.
| ||||
| CmplsDynTunnelOperStatus | 1.3.6.1.4.1.738.10.6.3.2.1.6.1.18 | INTEGER | RO | |
column · INTEGER · read-only · current See similar object in mplsManTunnelTable.
| ||||
| CmplsDynTunnelAttributes | 1.3.6.1.4.1.738.10.6.3.2.1.6.1.19 | Bits | RO | |
column · Bits · read-only · current See similar object in mplsManTunnelTable.
| ||||
| CmplsDynTunnelPathComp | 1.3.6.1.4.1.738.10.6.3.2.1.6.1.20 | INTEGER | RO | |
column · INTEGER · read-only · current See similar object in mplsManTunnelTable.
| ||||
| CmplsDynTunnelFastRerouteMode | 1.3.6.1.4.1.738.10.6.3.2.1.6.1.21 | INTEGER | RO | |
column · INTEGER · read-only · current See similar object in mplsManTunnelTable.
| ||||
| CmplsDynTunnelBackupSetupPrio | 1.3.6.1.4.1.738.10.6.3.2.1.6.1.22 | Integer32 (0..7) | RO | |
column · Integer32 (0..7) · read-only · current See similar object in mplsManTunnelTable. | ||||
| CmplsDynTunnelBackupHoldingPrio | 1.3.6.1.4.1.738.10.6.3.2.1.6.1.23 | Integer32 (0..7) | RO | |
column · Integer32 (0..7) · read-only · current See similar object in mplsManTunnelTable. | ||||
| CmplsDynTunnelBackupIncAny | 1.3.6.1.4.1.738.10.6.3.2.1.6.1.24 | MplsTunnelAffinity | RO | |
column · MplsTunnelAffinity · read-only · current See similar object in mplsManTunnelTable. | ||||
| CmplsDynTunnelBackupIncAll | 1.3.6.1.4.1.738.10.6.3.2.1.6.1.25 | MplsTunnelAffinity | RO | |
column · MplsTunnelAffinity · read-only · current See similar object in mplsManTunnelTable. | ||||
| CmplsDynTunnelBackupExcAny | 1.3.6.1.4.1.738.10.6.3.2.1.6.1.26 | MplsTunnelAffinity | RO | |
column · MplsTunnelAffinity · read-only · current See similar object in mplsManTunnelTable. | ||||
| CmplsDynTunnelBackupBandwidth | 1.3.6.1.4.1.738.10.6.3.2.1.6.1.27 | MplsBitRate | RO | |
column · MplsBitRate · read-only · current See similar object in mplsManTunnelTable.
| ||||
| CmplsDynTunnelBackupMaxHops | 1.3.6.1.4.1.738.10.6.3.2.1.6.1.28 | Unsigned32 (1..4294967295) | RO | |
column · Unsigned32 (1..4294967295) · read-only · current See similar object in mplsManTunnelTable. | ||||
| CmplsDynTunnelMtu | 1.3.6.1.4.1.738.10.6.3.2.1.6.1.29 | Integer32 | RO | |
column · Integer32 · read-only · current See similar object in mplsManTunnelTable. | ||||
| CmplsDynTunnelRebuildTimer | 1.3.6.1.4.1.738.10.6.3.2.1.6.1.30 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current See similar object in mplsManTunnelTable. | ||||
| CmplsDynTunnelOperStatusFlags | 1.3.6.1.4.1.738.10.6.3.2.1.6.1.31 | Bits | RO | |
column · Bits · read-only · current See similar object in mplsManTunnelTable.
| ||||
| CmplsDynTunnelGuardedDest | 1.3.6.1.4.1.738.10.6.3.2.1.6.1.32 | IpAddress | RO | |
column · IpAddress · read-only · current See similar object in mplsManTunnelTable. | ||||
| CmplsDynTunnelMBBTimeOut | 1.3.6.1.4.1.738.10.6.3.2.1.6.1.33 | Integer32 | RO | |
column · Integer32 · read-only · current See similar object in mplsManTunnelTable. | ||||
| CmplsDynTunnelOwner | 1.3.6.1.4.1.738.10.6.3.2.1.6.1.34 | MplsOwner | RO | |
column · MplsOwner · read-only · current See similar object in mplsManTunnelTable. | ||||
| CmplsDynTunnelARHopTableIndex | 1.3.6.1.4.1.738.10.6.3.2.1.6.1.35 | MplsPathIndexOrZero | RO | |
column · MplsPathIndexOrZero · read-only · current See similar object in mplsManTunnelTable. | ||||
| CmplsDynTunnelCHopTableIndex | 1.3.6.1.4.1.738.10.6.3.2.1.6.1.36 | MplsPathIndexOrZero | RO | |
column · MplsPathIndexOrZero · read-only · current See similar object in mplsManTunnelTable. | ||||
| SmplsTeObjectReserved7 | 1.3.6.1.4.1.738.10.6.3.2.1.7 | MplsTeObjectReservedTC | RW | |
scalar · MplsTeObjectReservedTC · read-write · current This object is reserved for future use. | ||||
| TmplsTunnelManHopTable | 1.3.6.1.4.1.738.10.6.3.2.1.8 | NA | ||
table · not-accessible · current The mplsTunnelManHopTable is used to indicate the hops, strict or loose, for an MPLS tunnel defined in mplsManTunnelTable, when it is established via signaling, for the outgoing direction of the tunnel. Each row in this table is indexed by mplsTunnelManHopListIndex. Each row also has a secondary index mplsTunnelManHopIndex corresponding to the next hop that this row corresponds to. The first row in the table is the first hop after the origination point of the tunnel. In case we want to specify a particular interface on the originating LSR of an outgoing tunnel by which we want packets to exit the LSR, we specify this as the first hop for this tunnel in mplsTunnelManHopTable. | ||||
| RmplsTunnelManHopEntry | 1.3.6.1.4.1.738.10.6.3.2.1.8.1 | NA | ||
row · not-accessible · current An entry in this table represents a tunnel hop. An entry is created by a network administrator for signaled ERLSP set up by an MPLS signaling protocol. | ||||
| CmplsTunnelManHopListIndex | 1.3.6.1.4.1.738.10.6.3.2.1.8.1.1 | MplsPathIndex | NA | |
column · MplsPathIndex · not-accessible · current Primary index into this table identifying a particular explicit route object. | ||||
| CmplsTunnelManHopPathOptionIndex | 1.3.6.1.4.1.738.10.6.3.2.1.8.1.2 | MplsPathIndex | NA | |
column · MplsPathIndex · not-accessible · current Secondary index into this table identifying a particular group of hops representing a particular configured path. This is otherwise known as a path option. | ||||
| CmplsTunnelManHopIndex | 1.3.6.1.4.1.738.10.6.3.2.1.8.1.3 | MplsPathIndex | NA | |
column · MplsPathIndex · not-accessible · current Secondary index into this table identifying a particular hop. | ||||
| CmplsTunnelManHopRowStatus | 1.3.6.1.4.1.738.10.6.3.2.1.8.1.4 | RowStatus | RC | |
column · RowStatus · read-create · current This variable is used to create, modify, and/or delete a row in this table. When a row in this table is in active(1) state, no objects in that row can be modified by the agent except mplsTunnelManHopRowStatus and mplsTunnelManHopStorageType. | ||||
| CmplsTunnelManHopEnable | 1.3.6.1.4.1.738.10.6.3.2.1.8.1.5 | TruthValue | RC | |
column · TruthValue · read-create · current Administratively enable or disable the hop. | ||||
| CmplsTunnelManHopAddrType | 1.3.6.1.4.1.738.10.6.3.2.1.8.1.6 | TeHopAddressType | RC | |
column · TeHopAddressType · read-create · current The Hop Address Type of this tunnel hop. The value of this object cannot be changed if the value of the corresponding mplsTunnelManHopRowStatus object is 'active'. Note that lspid(5) is a valid option only for tunnels signaled via CRLDP. | ||||
| CmplsTunnelManHopIpAddr | 1.3.6.1.4.1.738.10.6.3.2.1.8.1.7 | TeHopAddress | RC | |
column · TeHopAddress · read-create · current The Tunnel Hop Address for this tunnel hop. The type of this address is determined by the value of the corresponding mplsTunnelManHopAddrType. The value of this object cannot be changed if the value of the corresponding mplsTunnelManHopRowStatus object is 'active'. | ||||
| CmplsTunnelManHopIpPrefixLen | 1.3.6.1.4.1.738.10.6.3.2.1.8.1.8 | Unsigned32 | RC | |
column · Unsigned32 · read-create · current If mplsTunnelManHopAddrType is set to ipv4(1) or ipv6(2), then this value will contain an appropriate prefix length for the IP address in object mplsTunnelManHopIpAddr. Otherwise this value is irrelevant and should be ignored. | ||||
| CmplsTunnelManHopType | 1.3.6.1.4.1.738.10.6.3.2.1.8.1.9 | INTEGER | RC | |
column · INTEGER · read-create · current Denotes whether this tunnel hop is routed in a strict or loose fashion. The value of this object has no meaning if the mplsTunnelManHopInclude object is set to 'false'.
| ||||
| CmplsTunnelManHopInclude | 1.3.6.1.4.1.738.10.6.3.2.1.8.1.10 | TruthValue | RC | |
column · TruthValue · read-create · current If this value is set to true, then this indicates that this hop must be included in the tunnel's path. If this value is set to 'false', then this hop must be avoided when calculating the path for this tunnel. The default value of this object is 'true', so that by default all indicated hops are included in the CSPF path computation. If this object is set to 'false' the value of mplsTunnelManHopType should be ignored. | ||||
| SmplsTeObjectReserved9 | 1.3.6.1.4.1.738.10.6.3.2.1.9 | MplsTeObjectReservedTC | RW | |
scalar · MplsTeObjectReservedTC · read-write · current This object is reserved for future use. | ||||
| TmplsTunnelAutoHopTable | 1.3.6.1.4.1.738.10.6.3.2.1.10 | NA | ||
table · not-accessible · current Similar to mplsTunnelManHopTable but for automatic tunnels. | ||||
| RmplsTunnelAutoHopEntry | 1.3.6.1.4.1.738.10.6.3.2.1.10.1 | NA | ||
row · not-accessible · current See similar object in mplsTunnelManHopTable. | ||||
| CmplsTunnelAutoHopListIndex | 1.3.6.1.4.1.738.10.6.3.2.1.10.1.1 | MplsPathIndex | NA | |
column · MplsPathIndex · not-accessible · current See similar object in mplsTunnelManHopTable. | ||||
| CmplsTunnelAutoHopPathOptionIndex | 1.3.6.1.4.1.738.10.6.3.2.1.10.1.2 | MplsPathIndex | NA | |
column · MplsPathIndex · not-accessible · current See similar object in mplsTunnelManHopTable. | ||||
| CmplsTunnelAutoHopIndex | 1.3.6.1.4.1.738.10.6.3.2.1.10.1.3 | MplsPathIndex | NA | |
column · MplsPathIndex · not-accessible · current See similar object in mplsTunnelManHopTable. | ||||
| CmplsTunnelAutoHopAddrType | 1.3.6.1.4.1.738.10.6.3.2.1.10.1.4 | TeHopAddressType | RO | |
column · TeHopAddressType · read-only · current See similar object in mplsTunnelManHopTable. | ||||
| CmplsTunnelAutoHopIpAddr | 1.3.6.1.4.1.738.10.6.3.2.1.10.1.5 | TeHopAddress | RO | |
column · TeHopAddress · read-only · current See similar object in mplsTunnelManHopTable. | ||||
| CmplsTunnelAutoHopIpPrefixLen | 1.3.6.1.4.1.738.10.6.3.2.1.10.1.6 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current See similar object in mplsTunnelManHopTable. | ||||
| CmplsTunnelAutoHopType | 1.3.6.1.4.1.738.10.6.3.2.1.10.1.7 | INTEGER | RO | |
column · INTEGER · read-only · current See similar object in mplsTunnelManHopTable.
| ||||
| CmplsTunnelAutoHopInclude | 1.3.6.1.4.1.738.10.6.3.2.1.10.1.8 | TruthValue | RO | |
column · TruthValue · read-only · current See similar object in mplsTunnelManHopTable. | ||||
| SmplsTeObjectReserved11 | 1.3.6.1.4.1.738.10.6.3.2.1.11 | MplsTeObjectReservedTC | RW | |
scalar · MplsTeObjectReservedTC · read-write · current This object is reserved for future use. | ||||
| TmplsTunnelManResTable | 1.3.6.1.4.1.738.10.6.3.2.1.12 | NA | ||
table · not-accessible · current The mplsTunnelManResTable allows a manager to specify which resources are desired for an MPLS tunnel within the mplsManTunnelTable. This table also allows several tunnels to point to a single entry in this table, implying that these tunnels should share resources. | ||||
| RmplsTunnelManResEntry | 1.3.6.1.4.1.738.10.6.3.2.1.12.1 | NA | ||
row · not-accessible · current An entry in this table represents a set of resources for an MPLS tunnel. An entry can be created by a network administrator or by an SNMP agent as instructed by any MPLS signaling protocol. | ||||
| CmplsTunnelManResIndex | 1.3.6.1.4.1.738.10.6.3.2.1.12.1.1 | Unsigned32 (1..1073610751) | NA | |
column · Unsigned32 (1..1073610751) · not-accessible · current Uniquely identifies this row. | ||||
| CmplsTunnelManResRowStatus | 1.3.6.1.4.1.738.10.6.3.2.1.12.1.2 | RowStatus | RC | |
column · RowStatus · read-create · current This variable is used to create, modify, and/or delete a row in this table. | ||||
| CmplsTunnelManResMaxRate | 1.3.6.1.4.1.738.10.6.3.2.1.12.1.3 | MplsBitRate | RC | |
column · MplsBitRate · read-create · current The maximum rate in units of 1000 bits/second. Note that setting mplsTunnelManResMaxRate, mplsTunnelManResMeanRate, and mplsTunnelManResMaxBurstSize to 0 indicates best-effort treatment. This object is copied to an instance of mplsTrafficParamMaxRate in mplsTrafficParamTable the OID of which is copied into the corresponding mplsInSegmentTrafficParamPtr. If the ingress node sets a maximum rate of positive infinity, the egress node will return a value of positive infinity on the MIB GET response. This special value may not be used when setting the maximum rate with this MIB.
| ||||
| CmplsTunnelManResMeanRate | 1.3.6.1.4.1.738.10.6.3.2.1.12.1.4 | MplsBitRate | RC | |
column · MplsBitRate · read-create · current The mean rate in units of 1000 bits/second. This object is copied into an instance of mplsTrafficParamMeanRate in the mplsTrafficParamTable. The OID of this table entry is then copied into the corresponding mplsInSegmentTrafficParamPtr. When resource allocation is performed as requested by this TSpec object, it is copied into an entry in mplsTrafficParamTable [LSRMIB]: mplsTunnelInMeanRate to mplsTrafficParamMeanRate. The OID of this entry is copied to mplsInSegmentTrafficParamPtr of the corresponding in-segment entry.
| ||||
| CmplsTunnelManResMaxBurstSize | 1.3.6.1.4.1.738.10.6.3.2.1.12.1.5 | MplsBurstSize | RC | |
column · MplsBurstSize · read-create · current The maximum burst size in bytes. This object is copied to mplsInSegmentMaxBurstSize of the corresponding in-segment. When resource allocation is performed as requested by this TSpec object, it is copied into an entry in mplsTrafficParamTable [LSRMIB]: mplsTunnelInMaxBurstSize to mplsTrafficParamMaxBurstSize. The OID of this entry is copied to mplsInSegmentTrafficParamPtr of the corresponding in-segment entry.
| ||||
| CmplsTunnelManResMeanBurstSize | 1.3.6.1.4.1.738.10.6.3.2.1.12.1.6 | MplsBurstSize | RC | |
column · MplsBurstSize · read-create · current The mean burst size in bytes. The implementations which do not implement this variable must return 0 for this value and must not allow a user to set this value.
| ||||
| CmplsTunnelManResExBurstSize | 1.3.6.1.4.1.738.10.6.3.2.1.12.1.7 | MplsBurstSize | RO | |
column · MplsBurstSize · read-only · current The Excess burst size in bytes. The implementations which do not implement this variable must return noSuchObject(0) exception for this object and must not allow a user to set this value.
| ||||
| SmplsTeObjectReserved13 | 1.3.6.1.4.1.738.10.6.3.2.1.13 | MplsTeObjectReservedTC | RW | |
scalar · MplsTeObjectReservedTC · read-write · current This object is reserved for future use. | ||||
| TmplsTunnelAutoResTable | 1.3.6.1.4.1.738.10.6.3.2.1.14 | NA | ||
table · not-accessible · current Similar to mplsTunnelManResTable but for automatic tunnels. | ||||
| RmplsTunnelAutoResEntry | 1.3.6.1.4.1.738.10.6.3.2.1.14.1 | NA | ||
row · not-accessible · current See similar object in mplsTunnelManResTable. | ||||
| CmplsTunnelAutoResIndex | 1.3.6.1.4.1.738.10.6.3.2.1.14.1.1 | Unsigned32 (1073610752..1073741823) | NA | |
column · Unsigned32 (1073610752..1073741823) · not-accessible · current See similar object in mplsTunnelManResTable. | ||||
| CmplsTunnelAutoResMaxRate | 1.3.6.1.4.1.738.10.6.3.2.1.14.1.2 | MplsBitRate | RO | |
column · MplsBitRate · read-only · current See similar object in mplsTunnelManResTable.
| ||||
| CmplsTunnelAutoResMeanRate | 1.3.6.1.4.1.738.10.6.3.2.1.14.1.3 | MplsBitRate | RO | |
column · MplsBitRate · read-only · current See similar object in mplsTunnelManResTable.
| ||||
| CmplsTunnelAutoResMaxBurstSize | 1.3.6.1.4.1.738.10.6.3.2.1.14.1.4 | MplsBurstSize | RO | |
column · MplsBurstSize · read-only · current See similar object in mplsTunnelManResTable.
| ||||
| CmplsTunnelAutoResMeanBurstSize | 1.3.6.1.4.1.738.10.6.3.2.1.14.1.5 | MplsBurstSize | RO | |
column · MplsBurstSize · read-only · current See similar object in mplsTunnelManResTable.
| ||||
| CmplsTunnelAutoResExBurstSize | 1.3.6.1.4.1.738.10.6.3.2.1.14.1.6 | MplsBurstSize | RO | |
column · MplsBurstSize · read-only · current See similar object in mplsTunnelManResTable.
| ||||
| SmplsTeObjectReserved15 | 1.3.6.1.4.1.738.10.6.3.2.1.15 | MplsTeObjectReservedTC | RW | |
scalar · MplsTeObjectReservedTC · read-write · current This object is reserved for future use. | ||||
| TmplsTunnelDynResTable | 1.3.6.1.4.1.738.10.6.3.2.1.16 | NA | ||
table · not-accessible · current Similar to mplsTunnelManResTable but for dynamic tunnels. | ||||
| RmplsTunnelDynResEntry | 1.3.6.1.4.1.738.10.6.3.2.1.16.1 | NA | ||
row · not-accessible · current See similar object in mplsTunnelManResTable. | ||||
| CmplsTunnelDynResIndex | 1.3.6.1.4.1.738.10.6.3.2.1.16.1.1 | Unsigned32 (1073741824..2147483647) | NA | |
column · Unsigned32 (1073741824..2147483647) · not-accessible · current See similar object in mplsTunnelManResTable. | ||||
| CmplsTunnelDynResMaxRate | 1.3.6.1.4.1.738.10.6.3.2.1.16.1.2 | MplsBitRate | RO | |
column · MplsBitRate · read-only · current See similar object in mplsTunnelManResTable.
| ||||
| CmplsTunnelDynResMeanRate | 1.3.6.1.4.1.738.10.6.3.2.1.16.1.3 | MplsBitRate | RO | |
column · MplsBitRate · read-only · current See similar object in mplsTunnelManResTable.
| ||||
| CmplsTunnelDynResMaxBurstSize | 1.3.6.1.4.1.738.10.6.3.2.1.16.1.4 | MplsBurstSize | RO | |
column · MplsBurstSize · read-only · current See similar object in mplsTunnelManResTable.
| ||||
| CmplsTunnelDynResMeanBurstSize | 1.3.6.1.4.1.738.10.6.3.2.1.16.1.5 | MplsBurstSize | RO | |
column · MplsBurstSize · read-only · current See similar object in mplsTunnelManResTable.
| ||||
| CmplsTunnelDynResExBurstSize | 1.3.6.1.4.1.738.10.6.3.2.1.16.1.6 | MplsBurstSize | RO | |
column · MplsBurstSize · read-only · current See similar object in mplsTunnelManResTable.
| ||||
| CmplsTunnelDynResStorageType | 1.3.6.1.4.1.738.10.6.3.2.1.16.1.7 | MplsTunnelStorageType | RO | |
column · MplsTunnelStorageType · read-only · current See similar object in mplsTunnelManResTable. | ||||
| SmplsTeObjectReserved17 | 1.3.6.1.4.1.738.10.6.3.2.1.17 | MplsTeObjectReservedTC | RW | |
scalar · MplsTeObjectReservedTC · read-write · current This object is reserved for future use. | ||||
| TmplsTunnelARHopTable | 1.3.6.1.4.1.738.10.6.3.2.1.18 | NA | ||
table · not-accessible · current The mplsTunnelARHopTable is used to indicate the hops, strict or loose, for an MPLS tunnel defined in any of the three mplsTunnelTables, as reported by the MPLS signaling protocol, for the outgoing direction of the tunnel. Each row in this table is indexed by mplsTunnelARHopListIndex. Each row also has a secondary index mplsTunnelARHopIndex, corresponding to the next hop that this row corresponds to. The first row in the table is the first hop after the origination point of the tunnel. In case we want to specify a particular interface on the originating LSR of an outgoing tunnel by which we want packets to exit the LSR, we specify this as the first hop for this tunnel in mplsTunnelARHopTable. Please note that since the information necessary to build entries within this table are not provided by some MPLS signaling protocols, implementation of this table is optional. Furthermore, since the information in this table is actually provided by the MPLS signaling protocol after the path has been set-up, the entries in this table are provided only for observation, and hence, all variables in this table are accessible exclusively as read-only. | ||||
| RmplsTunnelARHopEntry | 1.3.6.1.4.1.738.10.6.3.2.1.18.1 | NA | ||
row · not-accessible · current An entry in this table represents a tunnel hop. An entry is created by a network administrator for signaled ERLSP set up by an MPLS signaling protocol. | ||||
| CmplsTunnelARHopListIndex | 1.3.6.1.4.1.738.10.6.3.2.1.18.1.1 | MplsPathIndex | NA | |
column · MplsPathIndex · not-accessible · current Primary index into this table identifying a particular recorded hop list. | ||||
| CmplsTunnelARHopIndex | 1.3.6.1.4.1.738.10.6.3.2.1.18.1.2 | MplsPathIndex | NA | |
column · MplsPathIndex · not-accessible · current Secondary index into this table identifying the particular hop. | ||||
| CmplsTunnelARHopAddrType | 1.3.6.1.4.1.738.10.6.3.2.1.18.1.3 | TeHopAddressType | RO | |
column · TeHopAddressType · read-only · current The Hop Address Type of this tunnel hop. If the type value is set to ipv4(1) or ipv6(2). The tunnel path can be determin using mplsTunnelARHopIpAddr object. mplsTunnelARHopAddrUnnum and mplsTunnelARHopLspId should not be used. If the type value is set to unnum(4) or unnumv6(6). The tunnel path can be determin using mplsTunnelARHopAddrUnnum object. mplsTunnelARHopIpAddr and mplsTunnelARHopLspId should not be used. Note that lspid(5) is a valid option only for tunnels signaled via CRLDP. The tunnel path can be determin using mplsTunnelARHopLspId object. mplsTunnelARHopIpAddr and mplsTunnelARHopAddrUnnum should not be used. Currently only ipv4(1) type is supported | ||||
| CmplsTunnelARHopIpAddr | 1.3.6.1.4.1.738.10.6.3.2.1.18.1.4 | TeHopAddress | RO | |
column · TeHopAddress · read-only · current The Tunnel Hop Address for this tunnel hop. The type of this address is determined by the value of the corresponding mplsTunnelARHopAddrType. If mplsTunnelARHopAddrType is set to ipv4(1) or ipv6(2), then this value contains the LSR Router ID of the unnumbered interface. Otherwise the agent SHOULD set this object to the zero-length string and the manager should ignore this object. | ||||
| SmplsTeObjectReserved19 | 1.3.6.1.4.1.738.10.6.3.2.1.19 | MplsTeObjectReservedTC | RW | |
scalar · MplsTeObjectReservedTC · read-write · current This object is reserved for future use. | ||||
| TmplsTunnelCHopTable | 1.3.6.1.4.1.738.10.6.3.2.1.20 | NA | ||
table · not-accessible · current The mplsTunnelCHopTable is used to indicate the hops, strict or loose, for an MPLS tunnel defined in any of three mplsManTunnelTables, as computed by a constraint-based routing protocol, based on the mplsTunnelManHopTable for the outgoing direction of the tunnel. Each row in this table is indexed by mplsTunnelCHopListIndex. Each row also has a secondary index mplsTunnelCHopIndex, corresponding to the next hop that this row corresponds to. The first row in the table is the first hop after the origination point of the tunnel. In case we want to specify a particular interface on the originating LSR of an outgoing tunnel by which we want packets to exit the LSR, we specify this as the first hop for this tunnel in mplsTunnelCHopTable. Please note that since the information necessary to build entries within this table may not be supported by some LSRs, implementation of this table is optional. Furthermore, since the information in this table is actually provided by routing protocol after the path has been computed, the entries in this table are provided only for observation, and hence, all variables in this table are accessible exclusively as read-only. | ||||
| RmplsTunnelCHopEntry | 1.3.6.1.4.1.738.10.6.3.2.1.20.1 | NA | ||
row · not-accessible · current An entry in this table represents a tunnel hop. An entry in this table is created by a constraint- based routing protocol based on the hops specified in the corresponding mplsTunnelManHopTable. | ||||
| CmplsTunnelCHopListIndex | 1.3.6.1.4.1.738.10.6.3.2.1.20.1.1 | MplsPathIndex | NA | |
column · MplsPathIndex · not-accessible · current Primary index into this table identifying a particular computed hop list. | ||||
| CmplsTunnelCHopIndex | 1.3.6.1.4.1.738.10.6.3.2.1.20.1.2 | MplsPathIndex | NA | |
column · MplsPathIndex · not-accessible · current Secondary index into this table identifying the particular hop. | ||||
| CmplsTunnelCHopAddrType | 1.3.6.1.4.1.738.10.6.3.2.1.20.1.3 | TeHopAddressType | RO | |
column · TeHopAddressType · read-only · current The Hop Address Type of this tunnel hop. Note that lspid(5) is a valid option only for tunnels signaled via CRLDP. | ||||
| CmplsTunnelCHopIpAddr | 1.3.6.1.4.1.738.10.6.3.2.1.20.1.4 | TeHopAddress | RO | |
column · TeHopAddress · read-only · current The Tunnel Hop Address for this tunnel hop. The type of this address is determined by the value of the corresponding mplsTunnelCHopAddrType. If mplsTunnelCHopAddrType is set to unnum(4) or unnumv6(6), then this value will contain the LSR Router ID of the unnumbered interface. Otherwise the agent should set this object to the zero-length string and the manager SHOULD ignore this object. | ||||
| CmplsTunnelCHopIpPrefixLen | 1.3.6.1.4.1.738.10.6.3.2.1.20.1.5 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current If mplsTunnelCHopAddrType is set to ipv4(1) or ipv6(2), then this value will contain an appropriate prefix length for the IP address in object mplsTunnelCHopIpAddr. Otherwise this value is irrelevant and should be ignored. | ||||
| CmplsTunnelCHopType | 1.3.6.1.4.1.738.10.6.3.2.1.20.1.6 | INTEGER | RO | |
column · INTEGER · read-only · current Denotes whether this is tunnel hop is routed in a strict or loose fashion.
| ||||
| SmplsTeObjectReserved21 | 1.3.6.1.4.1.738.10.6.3.2.1.21 | MplsTeObjectReservedTC | RW | |
scalar · MplsTeObjectReservedTC · read-write · current This object is reserved for future use. | ||||
| TprvtMplsTunnelTrapEnableTable | 1.3.6.1.4.1.738.10.6.3.2.1.22 | NA | ||
table · not-accessible · current The prvtMplsTunnelTrapEnable Table allows a manager to enable or disable TRAPs. | ||||
| RprvtMplsTunnelTrapEnableEntry | 1.3.6.1.4.1.738.10.6.3.2.1.22.1 | NA | ||
row · not-accessible · current An entry in this table is used to configure trap support for this instance of TE-MIB | ||||
| CprvtMplsTunnelTrapEnableValue | 1.3.6.1.4.1.738.10.6.3.2.1.22.1.1 | TruthValue | RC | |
column · TruthValue · read-create · current If this object is true, then it enables the generation of mplsTunnelUp and mplsTunnelDown traps, otherwise these traps are not emitted. | ||||
Textual conventions
MplsBitRateUnsigned32 (0..4294967295)Display hint:
dIf the value of this object is greater than zero, then this represents the bandwidth of this MPLS interface (or Label Switched Path) in units of '1,000 bits per second'. The value, when greater than zero, represents the bandwidth of this MPLS interface (rounded to the nearest 1,000) in units of 1,000 bits per second. If the bandwidth of the MPLS interface is between ((n * 1000) - 500) and ((n * 1000) + 499), the value of this object is n, such that n > 0. If the value of this object is 0 (zero), this means that the traffic over this MPLS interface is considered to be best effort.
MplsBurstSizeUnsigned32 (0..4294967295)Display hint:
dThe number of octets of MPLS data that the stream may send back-to-back without concern for policing. The value of zero indicates that an implementation does not support Burst Size.
MplsExtendedTunnelIdOctetTypeOCTET STRING (SIZE (4 | 16))Display hint:
1d.1d.1d.1dA unique identifier for an MPLS Tunnel. This represents an IPv4 address of the ingress or egress LSR for the tunnel. This value is derived from the Extended Tunnel Id in RSVP or the Ingress Router ID for CR-LDP. Currently, only octet string sizes of 4 are supported. String sizes of 16 are reserved for future use.
MplsGeneralizedLabelOCTET STRING (SIZE (0..255))Display hint:
1x:This value represents a generalized MPLS Label. The label contents are specific to the label being represented. Wherever an MplsGeneralizedLabel is copied to or from a signaling protocol message, it is copied byte for byte as is. Therefore, if the octet string is intended to represent multibyte values, it encodes those values in network (big-endian) byte order. This interpretation applies in particular to the non-generalized MPLS labels (32 bits) used in ATM, FR and generic MPLS networks.
MplsGeneralizedLabelTypeINTEGERgeneralizedLabel(2)mplsLabel(1)notValid(0)wavebandLabel(3)The label types that are defined for Generalized MPLS.
MplsLSPIDOCTET STRING (SIZE (2 | 6 | 32))A unique identifier within an MPLS network that is assigned to each LSP. This is assigned at the head end of the LSP and can be used by all LSRs to identify this LSP. This value is piggybacked by the signaling protocol when this LSP is signaled within the network. This identifier can then be used at each LSR to identify which labels are being swapped to other labels for this LSP. This object can also be used to disambiguate LSPs that share the same RSVP sessions between the same source and destination. For LSPs established using CR-LDP, the LSPID is composed of the ingress LSR Router ID (or any of its own IPv4 addresses) and a locally unique CR-LSP ID to that LSR. The first two bytes carry the CR-LSPID, and the remaining 4 bytes carry the Router ID. The LSPID is useful in network management, in CR-LSP repair, and in using an already established CR-LSP as a hop in an ER-TLV. For LSPs signaled using RSVP-TE, the LSP ID is defined as a 16-bit (2 byte) identifier used in the SENDER_TEMPLATE and the FILTER_SPEC that can be changed to allow a sender to share resources with itself. The length of this object should only be 2 or 6 bytes. If the length of this octet string is 2 bytes, then it must identify an RSVP-TE LSPID, or it is 6 bytes, it must contain a CR-LDP LSPID.
MplsOwnerINTEGERcli(9)crldp(5)dynamic(10)ldp(4)mplsVpn(8)other(2)policyAgent(7)rsvpTe(6)snmp(3)unknown(1)This object indicates the local network management subsystem that originally created the object(s) in question. The values of this enumeration are defined as follows: unknown(1) - the local network management subsystem cannot discern which component created the object. other(2) - the local network management subsystem is able to discern which component created the object, but the component is not listed within the following choices, e.g., command line interface (cli). snmp(3) - The Simple Network Management Protocol was used to configure this object initially. ldp(4) - The Label Distribution Protocol was used to configure this object initially. crldp(5) - The Constraint-Based Label Distribution Protocol was used to configure this object initially. rsvpTe(6) - The Resource Reservation Protocol was used to configure this object initially. policyAgent(7) - A policy agent (perhaps in combination with one of the above protocols) was used to configure this object initially. mplsVpn(8) - This label was configured for MPLS/BGP VPNs as defined in RFC2547. cli(9) - The CLI was used to configure this object initially. dynamic(10) - The tunnel has been created dynamically. An object created by any of the above choices MAY be modified or destroyed by the same or a different choice.
MplsPathIndexUnsigned32 (1..4294967295)Display hint:
dA unique value to index (by Path number) an entry in a table.
MplsPathIndexOrZeroUnsigned32 (0..4294967295)Display hint:
dA unique identifier used to identify a specific path used by a tunnel. A value of 0 (zero) means that no path is in use.
MplsTeObjectReservedTCInteger32Display hint:
dTC for mplsTeObjectReserved* objects.
MplsTunnelAffinityUnsigned32 (0..4294967295)Display hint:
dDescribes the configured 32-bit Include-any, include-all, or exclude-all constraint for constraint-based link selection.
MplsTunnelInstanceIndexUnsigned32 (0..4294967295)Display hint:
dThe tunnel entry with instance index 0 should refer to the configured tunnel interface (if one exists). Values greater than 0, but less than or equal to 65535, should be used to indicate signaled (or backup) tunnel LSP instances. For tunnel LSPs signaled using RSVP, this value should correspond to the RSVP LSP ID used for the RSVP-TE LSP. Values greater than 65535 apply to FRR detour instances.
MplsTunnelInterfaceIndexOrZeroInteger32 (0..2147483647)Display hint:
dThis textual convention is an extension of the IF-MIB::InterfaceIndex convention. The latter defines a greater than zero value used to identify an interface or interface sub-layer in the managed system. This extension permits the additional value of zero. The value zero is object-specific and must therefore be defined as part of the description of any object which uses this syntax. Examples of the usage of zero might include situations where interface was unknown, or when none or all interfaces need to be referenced.
MplsTunnelPrivateDataSyntaxOCTET STRING (SIZE (0..24))Display hint:
1x:Represents private data field.
MplsTunnelStorageTypeINTEGERnonVolatile(3)other(1)permanent(4)readOnly(5)unknown(0)volatile(2)Same as StorageType from SNMPv2-TC, except with unknown(0).
MplsTunnelTNAAddressOCTET STRING (SIZE (0..20))Display hint:
1x:TNA address of a tunnel.
TeHopAddressOCTET STRING (SIZE (0..32))Denotes a generic Tunnel hop address, that is, the address of a node which an LSP traverses, including the source and destination nodes. An address may be very concrete, for example, an IPv4 host address (i.e., with prefix length 32); if this IPv4 address is an interface address, then that particular interface must be traversed. An address may also specify an 'abstract node', for example, an IPv4 address with prefix length less than 32, in which case, the LSP can traverse any node whose address falls in that range. An address may also specify an Autonomous System (AS), in which case the LSP can traverse any node that falls within that AS. A TeHopAddress value is always interpreted within the context of an TeHopAddressType value. Every usage of the TeHopAddress TEXTUAL-CONVENTION is required to specify the TeHopAddressType object which provides the context. It is suggested that the TeHopAddressType object is logically registered before the object(s) which use the TeHopAddress TEXTUAL-CONVENTION if they appear in the same logical row. The value of a TeHopAddress object must always be consistent with the value of the associated TeHopAddressType object. Attempts to set a TeHopAddress object to a value which is inconsistent with the associated TeHopAddressType must fail with an inconsistentValue error.
TeHopAddressASUnsigned32Display hint:
dRepresents a two or four octet AS number. The AS number is represented in network byte order (MSB first). A two-octet AS number has the two MSB octets set to zero.
TeHopAddressTypeINTEGERasnumber(3)ipv4(1)ipv6(2)lspid(5)unknown(0)unnum(4)unnumv6(6)A value that represents a type of address for a Traffic Engineered (TE) Tunnel hop. unknown(0) An unknown address type. This value MUST be used if the value of the corresponding TeHopAddress object is a zero-length string. It may also be used to indicate a TeHopAddress which is not in one of the formats defined below. ipv4(1) An IPv4 network address as defined by the InetAddressIPv4 TEXTUAL-CONVENTION [RFC3291]. ipv6(2) A global IPv6 address as defined by the InetAddressIPv6 TEXTUAL-CONVENTION [RFC3291]. asnumber(3) An Autonomous System (AS) number as defined by the TeHopAddressAS TEXTUAL-CONVENTION. unnum(4) An unnumbered interface index as defined by the TeHopAddressUnnum TEXTUAL-CONVENTION. lspid(5) An LSP ID for TE Tunnels (RFC3212) as defined by the MplsLSPID TEXTUAL-CONVENTION. -- private Addition unnumv6(6) An unnumbered IPv6 interface index as defined by the TeHopAddressUnnumV6 TEXTUAL-CONVENTION. -- End private Addition Each definition of a concrete TeHopAddressType value must be accompanied by a definition of a TEXTUAL-CONVENTION for use with that TeHopAddress. To support future extensions, the TeHopAddressType TEXTUAL-CONVENTION SHOULD NOT be sub-typed in object type definitions. It MAY be sub-typed in compliance statements in order to require only a subset of these address types for a compliant implementation. Implementations must ensure that TeHopAddressType objects and any dependent objects (e.g., TeHopAddress objects) are consistent. An inconsistentValue error must be generated if an attempt to change a TeHopAddressType object would, for example, lead to an undefined TeHopAddress value that is not defined herein. In particular, TeHopAddressType/TeHopAddress pairs must be changed together if the address type changes (e.g., from ipv6(2) to ipv4(1)).
TeHopAddressUnnumUnsigned32Display hint:
dRepresents an unnumbered interface: octets contents encoding 1-4 unnumbered interface network-byte order The corresponding TeHopAddressType value is unnum(4).
Traps / Notifications
- mplsAutoTunnelDown
1.3.6.1.4.1.738.10.6.3.2.0.4 - mplsAutoTunnelUp
1.3.6.1.4.1.738.10.6.3.2.0.3 - mplsDynTunnelDown
1.3.6.1.4.1.738.10.6.3.2.0.6 - mplsDynTunnelUp
1.3.6.1.4.1.738.10.6.3.2.0.5 - mplsManTunnelDown
1.3.6.1.4.1.738.10.6.3.2.0.2 - mplsManTunnelReoptimized
1.3.6.1.4.1.738.10.6.3.2.0.7 - mplsManTunnelUp
1.3.6.1.4.1.738.10.6.3.2.0.1