PRVT-EPS-MIB
B.A.T.M. Advance TechnologiesPrivate MIB supporting Linear Ethernet Protection Switching (ITU-T G.8031)
snmptranslate -m PRVT-EPS-MIB -Tpsnmpwalk -v2c -c <community> -m PRVT-EPS-MIB <host> 1.3.6.1.4.1.738.1.5.132Imports
| IEEE8021-CFM-MIB | Dot1agCfmMDLevelOrNone, Dot1agCfmMepIdOrZero |
|---|---|
| PRVT-SERV-MIB | sdpInfoEntry |
| PRVT-SWITCH-MIB | switch |
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP |
| SNMPv2-SMI | Bits, Integer32, IpAddress, MODULE-IDENTITY, MibIdentifier, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, iso |
| SNMPv2-TC | DisplayString, PhysAddress, RowStatus, TEXTUAL-CONVENTION, TruthValue |
OID tree
| Name | OID | Type | Access | Status |
|---|---|---|---|---|
| IprvtEpsMib | 1.3.6.1.4.1.738.1.5.132 | |||
identity Private MIB supporting Linear Ethernet Protection Switching (ITU-T G.8031) | ||||
| NprvtEpsMibNotifications | 1.3.6.1.4.1.738.1.5.132.0 | |||
| !prvtEpsDefectAlarm | 1.3.6.1.4.1.738.1.5.132.0.1 | |||
notification · current 1. EPS service is either operational or not operational; 2. Failure of protocol defects. | ||||
| !prvtEpsSwitchoverAlarm | 1.3.6.1.4.1.738.1.5.132.0.2 | |||
notification · current The alarm is issued if the active link is changed, pointing to the path where the switchover occured.
| ||||
| !prvtEpsLostCommunication | 1.3.6.1.4.1.738.1.5.132.0.3 | |||
notification · current The alarm is issued in case of non reception of APS frames in three consecutive intervals each representing 5 seconds.
| ||||
| !prvtEpsRestoredCommunication | 1.3.6.1.4.1.738.1.5.132.0.4 | |||
notification · current APS frames are received normally after APS communication failure.
| ||||
| !prvtEpsSignalFailDetected | 1.3.6.1.4.1.738.1.5.132.0.5 | |||
notification · current The alarm is issued in case of CCMs are not received and (3.5 * CCMtime(CCMinterval)) has expired.
| ||||
| !prvtEpsSignalDegradeDetected | 1.3.6.1.4.1.738.1.5.132.0.6 | |||
notification · current The alarm is issued in case of monitored error threshold is crossed: 1W Jitter error, 2W Jitter error, Latency error, Frame loss error.
| ||||
| !prvtEpsProtctSignalFailDetected | 1.3.6.1.4.1.738.1.5.132.0.7 | |||
notification · current The alarm is issued in case of CCMs are not received on the protected link and (3.5 * CCMtime(CCMinterval)) has expired or the protected link is down.
| ||||
| !prvtEpsSignalFailRecovery | 1.3.6.1.4.1.738.1.5.132.0.8 | |||
notification · current The alarm is issued in case of CCMs start to be received correctly again after a prvtEpsSignalFailDetected alarm occured and (3.5 * CCMtime(CCMinterval)) timer no longer expires or the link is up .
| ||||
| !prvtEpsSignalDegradeRecovery | 1.3.6.1.4.1.738.1.5.132.0.9 | |||
notification · current The alarm is issued in case of monitored error threshold is crossed bellow limis: 1W Jitter error, 2W Jitter error, Latency error, Frame loss error.
| ||||
| !prvtEpsProtctSignalFailRecovery | 1.3.6.1.4.1.738.1.5.132.0.10 | |||
notification · current The alarm is issued in case of CCMs start to be received correctly again on the protected link after a prvtEpsProtctSignalFailDetected alarm occured and (3.5 * CCMtime(CCMinterval)) timer no longer expires or the link is up .
| ||||
| NprvtEpsMibObjects | 1.3.6.1.4.1.738.1.5.132.1 | |||
| NprvtEpsService | 1.3.6.1.4.1.738.1.5.132.1.1 | |||
| TprvtEpsServiceTable | 1.3.6.1.4.1.738.1.5.132.1.1.1 | NA | ||
table · not-accessible · current The table contains Ethernet Protection Switching services information. | ||||
| RprvtEpsServiceEntry | 1.3.6.1.4.1.738.1.5.132.1.1.1.1 | NA | ||
row · not-accessible · current Ethernet Protection Switching information about a specific service.
| ||||
| CprvtEpsSvcId | 1.3.6.1.4.1.738.1.5.132.1.1.1.1.1 | Unsigned32 (0..4294967295) | RO | |
column · Unsigned32 (0..4294967295) · read-only · current The service ID. | ||||
| CprvtEpsServiceCfmMdLevel | 1.3.6.1.4.1.738.1.5.132.1.1.1.1.2 | Dot1agCfmMDLevelOrNone | RC | |
column · Dot1agCfmMDLevelOrNone · read-create · current Value of the CFM MD level where the protected domain is situated. | ||||
| CprvtEpsServicePrimaryLocalCfmMep | 1.3.6.1.4.1.738.1.5.132.1.1.1.1.3 | Dot1agCfmMepIdOrZero | RC | |
column · Dot1agCfmMepIdOrZero · read-create · current Primary local CFM MEP Id. | ||||
| CprvtEpsServicePrimaryRemoteCfmMep | 1.3.6.1.4.1.738.1.5.132.1.1.1.1.4 | Dot1agCfmMepIdOrZero | RC | |
column · Dot1agCfmMepIdOrZero · read-create · current Primary remote CFM MEP Id. | ||||
| CprvtEpsServiceSecondaryLocalCfmMep | 1.3.6.1.4.1.738.1.5.132.1.1.1.1.5 | Dot1agCfmMepIdOrZero | RC | |
column · Dot1agCfmMepIdOrZero · read-create · current Backup local CFM MEP Id. | ||||
| CprvtEpsServiceSecondaryRemoteCfmMep | 1.3.6.1.4.1.738.1.5.132.1.1.1.1.6 | Dot1agCfmMepIdOrZero | RC | |
column · Dot1agCfmMepIdOrZero · read-create · current Backup remote CFM MEP Id. | ||||
| CprvtEpsServiceLocalState | 1.3.6.1.4.1.738.1.5.132.1.1.1.1.7 | PrvtEpsRequestStateType | RC | |
column · PrvtEpsRequestStateType · read-create · current Protection state of the local side. The values can be set: rsManualSwitch(7), rsClear(6) or rsLockoutOfProtection(15). The values can be get: rsNoRequest (0), rsDoNotRevert (1), rsReverseRequest (2), rsExercise (4), rsWaitToRestore (5), rsClear (6), rsManualSwitch (7), rsSignalDegrade (9), rsSignalFail (11), rsForcedSwitch (13), rsSignalFailForProtection (14), rsLockoutOfProtection (15). | ||||
| CprvtEpsServiceHoldOffTimer | 1.3.6.1.4.1.738.1.5.132.1.1.1.1.8 | Unsigned32 (0..10000) | RC | |
column · Unsigned32 (0..10000) · read-create · current Value of the Hold Off timer in msec (increments of 100msec). | ||||
| CprvtEpsServiceWaitToRestoreTimer | 1.3.6.1.4.1.738.1.5.132.1.1.1.1.9 | Unsigned32 (0 | 5..12) | RC | |
column · Unsigned32 (0 | 5..12) · read-create · current Value of the Wait To Restore timer in seconds (0 to disable it). | ||||
| CprvtEpsServiceApsChannel | 1.3.6.1.4.1.738.1.5.132.1.1.1.1.10 | TruthValue | RO | |
column · TruthValue · read-only · current Active APS communication. | ||||
| CprvtEpsServiceProtection | 1.3.6.1.4.1.738.1.5.132.1.1.1.1.11 | PrvtEpsProtectionType | RO | |
column · PrvtEpsProtectionType · read-only · current Type of protection (1+1 or 1:1). | ||||
| CprvtEpsServiceDirection | 1.3.6.1.4.1.738.1.5.132.1.1.1.1.12 | PrvtEpsDirectionType | RO | |
column · PrvtEpsDirectionType · read-only · current Type of protection (unidirectional or bidirectional). | ||||
| CprvtEpsServiceRevertive | 1.3.6.1.4.1.738.1.5.132.1.1.1.1.13 | TruthValue | RC | |
column · TruthValue · read-create · current Protection type (revertive or non-revertive). | ||||
| CprvtEpsServiceActivePath | 1.3.6.1.4.1.738.1.5.132.1.1.1.1.14 | PrvtEpsActivePathType | RO | |
column · PrvtEpsActivePathType · read-only · current Protected service active path. | ||||
| CprvtEpsServiceDegradeTestType | 1.3.6.1.4.1.738.1.5.132.1.1.1.1.15 | PrvtEpsMonitoringType | RC | |
column · PrvtEpsMonitoringType · read-create · current Type of test used for monitoring signal degrade situations. | ||||
| CprvtEpsServiceDegradeTestOwner | 1.3.6.1.4.1.738.1.5.132.1.1.1.1.16 | OCTET STRING (SIZE (0..32)) | RC | |
column · OCTET STRING (SIZE (0..32)) · read-create · current Owner of the SAA test used for monitoring. | ||||
| CprvtEpsServiceDegradeTestName | 1.3.6.1.4.1.738.1.5.132.1.1.1.1.17 | OCTET STRING (SIZE (0..32)) | RC | |
column · OCTET STRING (SIZE (0..32)) · read-create · current Name of the CFM or SAA test used for monitoring. | ||||
| CprvtEpsServiceDegradeTestEnable | 1.3.6.1.4.1.738.1.5.132.1.1.1.1.18 | TruthValue | RC | |
column · TruthValue · read-create · current Start/stop CFM or SAA test for performance monitoring. | ||||
| CprvtEpsServiceDefectFop | 1.3.6.1.4.1.738.1.5.132.1.1.1.1.19 | PrvtEpsDefectFopType | RO | |
column · PrvtEpsDefectFopType · read-only · current Defects noticed by APS protocol could be either none or a composition of the bits (0-3): fullyIncompatibleProvisioning(0) - occures by the reception of three APS frames with the incompatible 'B' bit value during the period of 22.5 seconds; protectionSwitchingIncomplete(1) - occures if the transmitted 'Requested Signal' and the received 'Bridged Signal' do not match for a period of 50ms or longer; protectionConfigurationMismatch(2) - working/protection configuration mismatch, occures by the reception of three APS frames from the working transport entity during the period of 22.5 seconds; epsConfigurationMismatch(3) - provisioning mismatch - for example the local side is set in revertive mode, the remote side is set in non revertive mode. | ||||
| CprvtEpsServiceOperationalStatus | 1.3.6.1.4.1.738.1.5.132.1.1.1.1.20 | TruthValue | RO | |
column · TruthValue · read-only · current The purpose of this status is to identify to the User whether this service is ready for running. The operational status can be up or down. When creating the service the operational status will be down. Receiving CCMs from both transport entities and establishment of APS on the protection transport entity will bring the operational status to up. | ||||
| CprvtEpsServicePrimaryStatus | 1.3.6.1.4.1.738.1.5.132.1.1.1.1.21 | PrvtEpsPathStatusType | RO | |
column · PrvtEpsPathStatusType · read-only · current Primary path state (psOk(0) or psFailed(1)). | ||||
| CprvtEpsServiceSecondaryStatus | 1.3.6.1.4.1.738.1.5.132.1.1.1.1.22 | PrvtEpsPathStatusType | RO | |
column · PrvtEpsPathStatusType · read-only · current Secondary path state (psOk(0) or psFailed(1)). | ||||
| CprvtEpsServiceRemoteState | 1.3.6.1.4.1.738.1.5.132.1.1.1.1.23 | PrvtEpsRequestStateType | RO | |
column · PrvtEpsRequestStateType · read-only · current Protection state of the remote side. The values can be get: rsNoRequest (0), rsDoNotRevert (1), rsReverseRequest (2), rsExercise (4), rsWaitToRestore (5), rsClear (6), rsManualSwitch (7), rsSignalDegrade (9), rsSignalFail (11), rsForcedSwitch (13), rsSignalFailForProtection (14), rsLockoutOfProtection (15). | ||||
| CprvtEpsServiceRemoteApsChannel | 1.3.6.1.4.1.738.1.5.132.1.1.1.1.24 | TruthValue | RO | |
column · TruthValue · read-only · current Active APS communication reported by the remote. | ||||
| CprvtEpsServiceRemoteProtection | 1.3.6.1.4.1.738.1.5.132.1.1.1.1.25 | PrvtEpsProtectionType | RO | |
column · PrvtEpsProtectionType · read-only · current Type of protection (1+1 or 1:1) reported by the remote. | ||||
| CprvtEpsServiceRemoteDirection | 1.3.6.1.4.1.738.1.5.132.1.1.1.1.26 | PrvtEpsDirectionType | RO | |
column · PrvtEpsDirectionType · read-only · current Type of protection (unidirectional or bidirectional) reported by the remote. | ||||
| CprvtEpsServiceRemoteRevertive | 1.3.6.1.4.1.738.1.5.132.1.1.1.1.27 | TruthValue | RO | |
column · TruthValue · read-only · current Protection type (revertive or non-revertive) reported by the remote. | ||||
| CprvtEpsServiceAdminFreeze | 1.3.6.1.4.1.738.1.5.132.1.1.1.1.28 | TruthValue | RC | |
column · TruthValue · read-create · current Used to freeze the state of the protection service. | ||||
| CprvtEpsServiceAdminStatus | 1.3.6.1.4.1.738.1.5.132.1.1.1.1.29 | INTEGER | RC | |
column · INTEGER · read-create · current Administrative status of the protection.
| ||||
| CprvtEpsServiceRowStatus | 1.3.6.1.4.1.738.1.5.132.1.1.1.1.30 | RowStatus | RC | |
column · RowStatus · read-create · current The status of the row. The writable columns in a row can not be changed if the row is active. All columns must have a valid value before a row can be activated. | ||||
| CprvtEpsServiceProtectionCounter | 1.3.6.1.4.1.738.1.5.132.1.1.1.1.31 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current Counts how many times the service has gone to Protection. | ||||
Textual conventions
PrvtEpsActivePathTypeINTEGERprotection(1)working(0)PrvtEpsDefectFopTypeBitsepsConfigurationMismatch(3)fullyIncompatibleProvisioning(0)protectionConfigurationMismatch(2)protectionSwitchingIncomplete(1)PrvtEpsDirectionTypeINTEGERdtBidirectional(1)dtUnidirectional(0)PrvtEpsMonitoringTypeINTEGERcfmPM(1)none(0)saa(2)PrvtEpsPathStatusTypeINTEGERpsFailed(1)psOk(0)Status of the primary or backup links
PrvtEpsProtectionTypeINTEGERpt1Plus1(0)pt1To1(1)PrvtEpsRequestStateTypeINTEGERrsClear(6)rsDoNotRevert(1)rsExercise(4)rsForcedSwitch(13)rsLockoutOfProtection(15)rsManualSwitch(7)rsNoRequest(0)rsNone(-1)rsReverseRequest(2)rsSignalDegrade(9)rsSignalFail(11)rsSignalFailForProtection(14)rsWaitToRestore(5)
Traps / Notifications
- prvtEpsDefectAlarm
1.3.6.1.4.1.738.1.5.132.0.1 - prvtEpsLostCommunication
1.3.6.1.4.1.738.1.5.132.0.3 - prvtEpsProtctSignalFailDetected
1.3.6.1.4.1.738.1.5.132.0.7 - prvtEpsProtctSignalFailRecovery
1.3.6.1.4.1.738.1.5.132.0.10 - prvtEpsRestoredCommunication
1.3.6.1.4.1.738.1.5.132.0.4 - prvtEpsSignalDegradeDetected
1.3.6.1.4.1.738.1.5.132.0.6 - prvtEpsSignalDegradeRecovery
1.3.6.1.4.1.738.1.5.132.0.9 - prvtEpsSignalFailDetected
1.3.6.1.4.1.738.1.5.132.0.5 - prvtEpsSignalFailRecovery
1.3.6.1.4.1.738.1.5.132.0.8 - prvtEpsSwitchoverAlarm
1.3.6.1.4.1.738.1.5.132.0.2