snmptranslate -m ULAFPLUS-MIB -Tpsnmpwalk -v2c -c <community> -m ULAFPLUS-MIB <host> 1.3.6.1.4.1.1887Imports
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP |
|---|---|
| SNMPv2-SMI | Bits, Counter32, Gauge32, Integer32, IpAddress, MODULE-IDENTITY, MibIdentifier, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, enterprises, iso |
| SNMPv2-TC | DisplayString, PhysAddress, TEXTUAL-CONVENTION |
OID tree
| Name | OID | Type | Access | Status |
|---|---|---|---|---|
| NsiemensCH | 1.3.6.1.4.1.1887 | |||
| Nlineintegrator | 1.3.6.1.4.1.1887.1 | |||
| Nulaf2 | 1.3.6.1.4.1.1887.1.1 | |||
| Nlinks | 1.3.6.1.4.1.1887.1.1.4 | |||
| NlinksVers3 | 1.3.6.1.4.1.1887.1.1.4.3 | |||
| Ncmro | 1.3.6.1.4.1.1887.1.1.4.3.1 | |||
| TcmroHtuLocalTable | 1.3.6.1.4.1.1887.1.1.4.3.1.1 | NA | mandatory | |
| RcmroHtuLocalEntry | 1.3.6.1.4.1.1887.1.1.4.3.1.1.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CcmroHtuLocalPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.1.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CcmroHtuLocalLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.1.1.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CcmroHtuLocalHwFabData | 1.3.6.1.4.1.1887.1.1.4.3.1.1.1.3 | DisplayString (SIZE (20)) | RO | mandatory |
column · DisplayString (SIZE (20)) · read-only · mandatory Device Hardware Fabrication Data | ||||
| CcmroHtuLocalActFwType | 1.3.6.1.4.1.1887.1.1.4.3.1.1.1.4 | DisplayString | RO | mandatory |
column · DisplayString · read-only · mandatory Type of active Firmware | ||||
| CcmroHtuLocalActFwVers | 1.3.6.1.4.1.1887.1.1.4.3.1.1.1.5 | DisplayString | RO | mandatory |
column · DisplayString · read-only · mandatory Version of active Firmware | ||||
| CcmroHtuLocalPasBankState | 1.3.6.1.4.1.1887.1.1.4.3.1.1.1.6 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory State of passive firmware bank 1 Empty contains no firmware 2 Loaded contains a valid firmware 3 Foreign contains regenerator firmware 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroHtuLocalPasFwType | 1.3.6.1.4.1.1887.1.1.4.3.1.1.1.7 | DisplayString | RO | mandatory |
column · DisplayString · read-only · mandatory Type of passive firmware | ||||
| CcmroHtuLocalPasFwVers | 1.3.6.1.4.1.1887.1.1.4.3.1.1.1.8 | DisplayString | RO | mandatory |
column · DisplayString · read-only · mandatory Version of passive firmware | ||||
| CcmroHtuLocalSeepromVers | 1.3.6.1.4.1.1887.1.1.4.3.1.1.1.9 | DisplayString | RO | mandatory |
column · DisplayString · read-only · mandatory Version of SEEPROM data format | ||||
| CcmroHtuLocalDFabData | 1.3.6.1.4.1.1887.1.1.4.3.1.1.1.10 | DisplayString (SIZE (20)) | RO | mandatory |
column · DisplayString (SIZE (20)) · read-only · mandatory Fabrication Data of Data-Module | ||||
| CcmroHtuLocalDType | 1.3.6.1.4.1.1887.1.1.4.3.1.1.1.11 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Type of Data-Module in corresponding module-slot of the device. 1 None No module inserted 2 DCE Data module with DCE configuration 3 DTE Data module with DTE configuration 4 10Base-T 10Base-T Ethernet module 5 ABAR Advanced Bridge and Router module 254 unknown value 255 unsupported variable for addressed device For details of the module (connector sub-types, ...) the fabrication data has to evaluated
| ||||
| CcmroHtuLocalTFabData | 1.3.6.1.4.1.1887.1.1.4.3.1.1.1.12 | DisplayString (SIZE (20)) | RO | mandatory |
column · DisplayString (SIZE (20)) · read-only · mandatory Fabrication Data of 2Mbit-Module | ||||
| CcmroHtuLocalTType | 1.3.6.1.4.1.1887.1.1.4.3.1.1.1.13 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Type of 2Mbit-Module in corresponding module-slot of the device. 1 None No module present 2 TwoMbps A 2Mbit/s module is present 3 QuadTwoMbps A Quad 2Mbit/s module is present 4 CodirTwoMbps A Co-Directional G.703 module is present 5 TwoMbpsVarImp A 2Mbit/s module with variable impedance is present 6 QuadTwoMbpsVarImp A Quad 2Mbit/s module with variable impedance is present 7 FourTwoMbpsVarImp Module with four independent 2Mbit/s (variable impedance) is present 254 unknown value 255 unsupported variable for addressed device For details of the module (connector sub-types, ...) the fabrication data has to evaluated
| ||||
| CcmroHtuLocalRpsFabData | 1.3.6.1.4.1.1887.1.1.4.3.1.1.1.14 | DisplayString (SIZE (20)) | RO | mandatory |
column · DisplayString (SIZE (20)) · read-only · mandatory Fabrication Data of Remote Power Supply (RPS) Module | ||||
| CcmroHtuLocalRpsType | 1.3.6.1.4.1.1887.1.1.4.3.1.1.1.15 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Type of Remote Power Supply (RPS) Module in corresponding module-slot of the device. 1 None No module inserted 2 Rps A RPS module is inserted 254 unknown value 255 unsupported variable for addressed device For details of the module (connector sub-types, ...) the fabrication data has to evaluated
| ||||
| CcmroHtuLocalClkFabData | 1.3.6.1.4.1.1887.1.1.4.3.1.1.1.16 | DisplayString (SIZE (20)) | RO | mandatory |
column · DisplayString (SIZE (20)) · read-only · mandatory Fabrication Data of Clock and Alarm Module | ||||
| CcmroHtuLocalClkType | 1.3.6.1.4.1.1887.1.1.4.3.1.1.1.17 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Type of Clock and Alarm Module in corresponding module-slot of the device. 1 None No module inserted 2 ClockAlarm A combined Clock and Alarm module is inserted 3 Clock A Clock module is inserted 3 Alarm An Alarm module is inserted 254 unknown value 255 unsupported variable for addressed device For details of the module (connector sub-types, ...) the fabrication data has to evaluated
| ||||
| CcmroHtuLocalDbgFabData | 1.3.6.1.4.1.1887.1.1.4.3.1.1.1.18 | DisplayString (SIZE (20)) | RO | mandatory |
column · DisplayString (SIZE (20)) · read-only · mandatory Fabrication Data of Debug-Module | ||||
| CcmroHtuLocalDbgType | 1.3.6.1.4.1.1887.1.1.4.3.1.1.1.19 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Type of Debug-Module in corresponding module-slot of the device. 1 None No module inserted 2 Debug A Debug module is inserted 254 unknown value 255 unsupported variable for addressed device For details of the module (connector sub-types, ...) the fabrication data has to evaluated
| ||||
| CcmroHtuLocalHousing | 1.3.6.1.4.1.1887.1.1.4.3.1.1.1.20 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Type of housing / installation of the device. 1 Rack The device is a line card to be installed in a sub-rack 2 Desktop The device is a desktop device 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroHtuLocalRackVersion | 1.3.6.1.4.1.1887.1.1.4.3.1.1.1.21 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Version of the sub-rack in which the device is installed. 1 RackV1 The device is installed in a rack with V1 2 RackV2 The device is installed in a rack with V2 3 RackV3 The device is installed in a rack with V3 4 Desktop The device is a desktop device (and therefore not installed in a sub-rack) 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroHtuLocalLtNtType | 1.3.6.1.4.1.1887.1.1.4.3.1.1.1.22 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether the device is configured as LT or NT. 1 LT The device is configured as LT 2 NT The device is configured as NT 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroHtuLocalHdslChipset | 1.3.6.1.4.1.1887.1.1.4.3.1.1.1.23 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates which chipset the partner device uses for HDSL transmission 1 Level1 The partner device uses a Level 1 chipset 2 Metalink The partner device uses a MetaLink chipset 3 Infineon The partner device uses an Infineon chipset 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroHtuLocalDipCfg | 1.3.6.1.4.1.1887.1.1.4.3.1.1.1.24 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether the device is configured through DIP Switches. 1 Disabled The device can be configured through management software 2 Enabled The device is configured by DIP switches 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroHtuLocalEocCfg | 1.3.6.1.4.1.1887.1.1.4.3.1.1.1.25 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates how far the EOC has been built up. 1 Disabled The device can be configured locally 2 Enabled The device is being configured over the EOC 3 Reg1 The EOC is up until the first regenerator section 4 Reg2 The EOC is up until the second regenerator section 5 Reg3 The EOC is up until the third regenerator section 6 Reg4 The EOC is up until the fourth regenerator section 7 Reg5 The EOC is up until the fifth regenerator section 8 Reg6 The EOC is up until the sixth regenerator section 9 Reg7 The EOC is up until the seventh regenerator section 10 Reg8 The EOC is up until the eighth regenerator section 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroHtuLocalRpsVoltage | 1.3.6.1.4.1.1887.1.1.4.3.1.1.1.26 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates which Remote Power Supply (RPS) Voltage is being used by the device 1 V120 The RPS uses 120 Volts 2 V180 The RPS uses 180 Volts 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroHtuLocalPowerConfiguration | 1.3.6.1.4.1.1887.1.1.4.3.1.1.1.27 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates which kind of power supply is equiped 1 multifunctional No redundant supply possible 2 redundant Redundant supply possible 3 remoteFeeding Remote feeding possible 4 batteryDC DC-only supply 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroHtuLocalIsdnFabData | 1.3.6.1.4.1.1887.1.1.4.3.1.1.1.28 | DisplayString (SIZE (20)) | RO | mandatory |
column · DisplayString (SIZE (20)) · read-only · mandatory Fabrication Data of ISDN-Module | ||||
| CcmroHtuLocalIsdnType | 1.3.6.1.4.1.1887.1.1.4.3.1.1.1.29 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Type of ISDN-Module in corresponding module-slot of the device 1 None No module inserted 2 TE A module for S0(TE mode) operation is inserted 3 NT A module for S0(NT mode) operation is inserted 4 Uk0 A module for Uk0 operation is inserted 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroHtuLocalTipRingReversal1 | 1.3.6.1.4.1.1887.1.1.4.3.1.1.1.30 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether tip-ring reversal has been detected and compensated for on the first wire pair 1 No Reversal not detected 2 Yes Reversal detected and compensated for 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroHtuLocalTipRingReversal2 | 1.3.6.1.4.1.1887.1.1.4.3.1.1.1.31 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether tip-ring reversal has been detected and compensated for on the second wire pair 1 No Reversal not detected 2 Yes Reversal detected and compensated for 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroHtuLocalTipRingReversal3 | 1.3.6.1.4.1.1887.1.1.4.3.1.1.1.32 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether tip-ring reversal has been detected and compensated for on the third wire pair 1 No Reversal not detected 2 Yes Reversal detected and compensated for 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroHtuLocalTipRingReversal4 | 1.3.6.1.4.1.1887.1.1.4.3.1.1.1.33 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether tip-ring reversal has been detected and compensated for on the fourth wire pair 1 No Reversal not detected 2 Yes Reversal detected and compensated for 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroHtuLocalPacketFabData | 1.3.6.1.4.1.1887.1.1.4.3.1.1.1.34 | DisplayString (SIZE (20)) | RO | mandatory |
column · DisplayString (SIZE (20)) · read-only · mandatory Fabrication Data of L2 Switch | ||||
| CcmroHtuLocalPacketType | 1.3.6.1.4.1.1887.1.1.4.3.1.1.1.35 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Type of L2 Switch module. 1 None No module inserted 2 4P10/100 4-Port 10/100Base-T ethernet switch 3 1P10/100 1-Port 10/100Base-T ethernet switch 4 2P10/100 2-Port 10/100Base-T ethernet switch 5 3P10/100 3-Port 10/100Base-T ethernet switch 254 unknown value 255 unsupported variable for addressed device For details of the module (connector sub-types, ...) the fabrication data has to evaluated
| ||||
| CcmroHtuLocalPacketMacAddr1 | 1.3.6.1.4.1.1887.1.1.4.3.1.1.1.36 | OCTET STRING (SIZE (6)) | RO | mandatory |
column · OCTET STRING (SIZE (6)) · read-only · mandatory MAC address of L2 ethernet switch. Value of Byte 0..5 Meaning 0x00 - 0xFD MAC address all 0xFE unknown value all 0xFF unsupported variable | ||||
| CcmroHtuLocalMcsCh1aIsRemCh | 1.3.6.1.4.1.1887.1.1.4.3.1.1.1.37 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates MCS channel crossover. This variable shows which MCS channel the local channel a is conntected to on the far end MCS device. 1 U1/VA first interface (SHDSL U1 or G.704 VA) 2 U2/VB second interface (SHDSL U2 or G.704 VB) 3 U3/VC third interface (SHDSL U3 or G.704 VC) 4 U4/VD fourth interface (SHDSL U4 or G.704 VD) 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroHtuLocalMcsCh2bIsRemCh | 1.3.6.1.4.1.1887.1.1.4.3.1.1.1.38 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates MCS channel crossover. This variable shows which MCS channel the local channel b is conntected to on the far end MCS device. 1 U1/VA first interface (SHDSL U1 or G.704 VA) 2 U2/VB second interface (SHDSL U2 or G.704 VB) 3 U3/VC third interface (SHDSL U3 or G.704 VC) 4 U4/VD fourth interface (SHDSL U4 or G.704 VD) 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroHtuLocalMcsCh3cIsRemCh | 1.3.6.1.4.1.1887.1.1.4.3.1.1.1.39 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates MCS channel crossover. This variable shows which MCS channel the local channel c is conntected to on the far end MCS device. 1 U1/VA first interface (SHDSL U1 or G.704 VA) 2 U2/VB second interface (SHDSL U2 or G.704 VB) 3 U3/VC third interface (SHDSL U3 or G.704 VC) 4 U4/VD fourth interface (SHDSL U4 or G.704 VD) 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroHtuLocalMcsCh4dIsRemCh | 1.3.6.1.4.1.1887.1.1.4.3.1.1.1.40 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates MCS channel crossover. This variable shows which MCS channel the local channel d is conntected to on the far end MCS device. 1 U1/VA first interface (SHDSL U1 or G.704 VA) 2 U2/VB second interface (SHDSL U2 or G.704 VB) 3 U3/VC third interface (SHDSL U3 or G.704 VC) 4 U4/VD fourth interface (SHDSL U4 or G.704 VD) 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroHtuLocalMcsFarCh1aIsRemCh | 1.3.6.1.4.1.1887.1.1.4.3.1.1.1.41 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates MCS channel crossover. This variable shows which MCS channel the remote channel a is conntected to on the local end MCS device. 1 U1/VA first interface (SHDSL U1 or G.704 VA) 2 U2/VB second interface (SHDSL U2 or G.704 VB) 3 U3/VC third interface (SHDSL U3 or G.704 VC) 4 U4/VD fourth interface (SHDSL U4 or G.704 VD) 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroHtuLocalMcsFarCh2bIsRemCh | 1.3.6.1.4.1.1887.1.1.4.3.1.1.1.42 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates MCS channel crossover. This variable shows which MCS channel the remote channel b is conntected to on the local end MCS device. 1 U1/VA first interface (SHDSL U1 or G.704 VA) 2 U2/VB second interface (SHDSL U2 or G.704 VB) 3 U3/VC third interface (SHDSL U3 or G.704 VC) 4 U4/VD fourth interface (SHDSL U4 or G.704 VD) 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroHtuLocalMcsFarCh3cIsRemCh | 1.3.6.1.4.1.1887.1.1.4.3.1.1.1.43 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates MCS channel crossover. This variable shows which MCS channel the remote channel c is conntected to on the local end MCS device. 1 U1/VA first interface (SHDSL U1 or G.704 VA) 2 U2/VB second interface (SHDSL U2 or G.704 VB) 3 U3/VC third interface (SHDSL U3 or G.704 VC) 4 U4/VD fourth interface (SHDSL U4 or G.704 VD) 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroHtuLocalMcsFarCh4dIsRemCh | 1.3.6.1.4.1.1887.1.1.4.3.1.1.1.44 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates MCS channel crossover. This variable shows which MCS channel the remote channel d is conntected to on the local end MCS device. 1 U1/VA first interface (SHDSL U1 or G.704 VA) 2 U2/VB second interface (SHDSL U2 or G.704 VB) 3 U3/VC third interface (SHDSL U3 or G.704 VC) 4 U4/VD fourth interface (SHDSL U4 or G.704 VD) 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroHtuLocalDslChipset | 1.3.6.1.4.1.1887.1.1.4.3.1.1.1.45 | DisplayString (SIZE (20)) | RO | mandatory |
column · DisplayString (SIZE (20)) · read-only · mandatory Type of xDSL chipset | ||||
| CcmroHtuLocalDslFwLoad | 1.3.6.1.4.1.1887.1.1.4.3.1.1.1.46 | DisplayString (SIZE (20)) | RO | mandatory |
column · DisplayString (SIZE (20)) · read-only · mandatory Type of firmware load of xDSL chipset | ||||
| CcmroHtuLocalFpgaLoad | 1.3.6.1.4.1.1887.1.1.4.3.1.1.1.47 | DisplayString (SIZE (20)) | RO | mandatory |
column · DisplayString (SIZE (20)) · read-only · mandatory Type of FPGA load | ||||
| CcmroHtuLocalEthWanChip | 1.3.6.1.4.1.1887.1.1.4.3.1.1.1.48 | DisplayString (SIZE (20)) | RO | mandatory |
column · DisplayString (SIZE (20)) · read-only · mandatory Type of WAN chip which connects L2 switch and xDSL link | ||||
| CcmroHtuLocalSwitchChip | 1.3.6.1.4.1.1887.1.1.4.3.1.1.1.49 | DisplayString (SIZE (20)) | RO | mandatory |
column · DisplayString (SIZE (20)) · read-only · mandatory Type of Switch Chip | ||||
| CcmroHtuLocalBootloaderVers | 1.3.6.1.4.1.1887.1.1.4.3.1.1.1.50 | DisplayString (SIZE (20)) | RO | mandatory |
column · DisplayString (SIZE (20)) · read-only · mandatory Version of firmware boot loader | ||||
| CcmroHtuLocalSerialNumber | 1.3.6.1.4.1.1887.1.1.4.3.1.1.1.51 | DisplayString (SIZE (20)) | RO | mandatory |
column · DisplayString (SIZE (20)) · read-only · mandatory Serial number of device | ||||
| CcmroHtuLocalHwManufacturingDate | 1.3.6.1.4.1.1887.1.1.4.3.1.1.1.52 | DisplayString | RO | mandatory |
column · DisplayString · read-only · mandatory Manufacturing Date of the motherboard | ||||
| CcmroHtuLocalRpsManufacturingDate | 1.3.6.1.4.1.1887.1.1.4.3.1.1.1.53 | DisplayString | RO | mandatory |
column · DisplayString · read-only · mandatory Manufacturing Date of the RPS Module | ||||
| CcmroHtuLocalClkManufacturingDate | 1.3.6.1.4.1.1887.1.1.4.3.1.1.1.54 | DisplayString | RO | mandatory |
column · DisplayString · read-only · mandatory Manufacturing Date of the Clock and Alarm Module | ||||
| CcmroHtuLocalTManufacturingDate | 1.3.6.1.4.1.1887.1.1.4.3.1.1.1.55 | DisplayString | RO | mandatory |
column · DisplayString · read-only · mandatory Manufacturing Date of the 2Mbps Module | ||||
| CcmroHtuLocalDManufacturingDate | 1.3.6.1.4.1.1887.1.1.4.3.1.1.1.56 | DisplayString | RO | mandatory |
column · DisplayString · read-only · mandatory Manufacturing Date of the Data Module | ||||
| CcmroHtuLocalPacketManufacturingDate | 1.3.6.1.4.1.1887.1.1.4.3.1.1.1.57 | DisplayString | RO | mandatory |
column · DisplayString · read-only · mandatory Manufacturing Date of the Packet Module | ||||
| CcmroHtuLocalL2SDriverVersion | 1.3.6.1.4.1.1887.1.1.4.3.1.1.1.58 | DisplayString | RO | mandatory |
column · DisplayString · read-only · mandatory L2 Switch Driver Version | ||||
| TcmroHtuFarTable | 1.3.6.1.4.1.1887.1.1.4.3.1.2 | NA | mandatory | |
| RcmroHtuFarEntry | 1.3.6.1.4.1.1887.1.1.4.3.1.2.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CcmroHtuFarPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.1.2.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CcmroHtuFarLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.1.2.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CcmroHtuFarHwFabData | 1.3.6.1.4.1.1887.1.1.4.3.1.2.1.3 | DisplayString (SIZE (20)) | RO | mandatory |
column · DisplayString (SIZE (20)) · read-only · mandatory Device Hardware Fabrication Data | ||||
| CcmroHtuFarActFwType | 1.3.6.1.4.1.1887.1.1.4.3.1.2.1.4 | DisplayString | RO | mandatory |
column · DisplayString · read-only · mandatory Type of active Firmware | ||||
| CcmroHtuFarActFwVers | 1.3.6.1.4.1.1887.1.1.4.3.1.2.1.5 | DisplayString | RO | mandatory |
column · DisplayString · read-only · mandatory Version of active Firmware | ||||
| CcmroHtuFarPasBankState | 1.3.6.1.4.1.1887.1.1.4.3.1.2.1.6 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory State of passive firmware bank 1 Empty contains no firmware 2 Loaded contains a valid firmware 3 Foreign contains regenerator firmware 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroHtuFarPasFwType | 1.3.6.1.4.1.1887.1.1.4.3.1.2.1.7 | DisplayString | RO | mandatory |
column · DisplayString · read-only · mandatory Type of passive firmware | ||||
| CcmroHtuFarPasFwVers | 1.3.6.1.4.1.1887.1.1.4.3.1.2.1.8 | DisplayString | RO | mandatory |
column · DisplayString · read-only · mandatory Version of passive firmware | ||||
| CcmroHtuFarSeepromVers | 1.3.6.1.4.1.1887.1.1.4.3.1.2.1.9 | DisplayString | RO | mandatory |
column · DisplayString · read-only · mandatory Version of SEEPROM data format | ||||
| CcmroHtuFarDFabData | 1.3.6.1.4.1.1887.1.1.4.3.1.2.1.10 | DisplayString (SIZE (20)) | RO | mandatory |
column · DisplayString (SIZE (20)) · read-only · mandatory Fabrication Data of Data-Module | ||||
| CcmroHtuFarDType | 1.3.6.1.4.1.1887.1.1.4.3.1.2.1.11 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Type of Data-Module in corresponding module-slot of the device. 1 None No module inserted 2 DCE Data module with DCE configuration 3 DTE Data module with DTE configuration 4 10Base-T 10Base-T Ethernet module 5 ABAR Advanced Bridge and Router module 254 unknown value 255 unsupported variable for addressed device For details of the module (connector sub-types, ...) the fabrication data has to evaluated
| ||||
| CcmroHtuFarTFabData | 1.3.6.1.4.1.1887.1.1.4.3.1.2.1.12 | DisplayString (SIZE (20)) | RO | mandatory |
column · DisplayString (SIZE (20)) · read-only · mandatory Fabrication Data of 2Mbit-Module | ||||
| CcmroHtuFarTType | 1.3.6.1.4.1.1887.1.1.4.3.1.2.1.13 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Type of 2Mbit-Module in corresponding module-slot of the device. 1 None No module present 2 TwoMbps A 2Mbit/s module is present 3 QuadTwoMbps A Quad 2Mbit/s module is present 4 CodirTwoMbps A Co-Directional G.703 module is present 5 TwoMbpsVarImp A 2Mbit/s module with variable impedance is present 6 QuadTwoMbpsVarImp A Quad 2Mbit/s module with variable impedance is present 7 FourTwoMbpsVarImp Module with four independent 2Mbit/s (variable impedance) is present 254 unknown value 255 unsupported variable for addressed device For details of the module (connector sub-types, ...) the fabrication data has to evaluated
| ||||
| CcmroHtuFarRpsFabData | 1.3.6.1.4.1.1887.1.1.4.3.1.2.1.14 | DisplayString (SIZE (20)) | RO | mandatory |
column · DisplayString (SIZE (20)) · read-only · mandatory Fabrication Data of Remote Power Supply (RPS) Module | ||||
| CcmroHtuFarRpsType | 1.3.6.1.4.1.1887.1.1.4.3.1.2.1.15 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Type of Remote Power Supply (RPS) Module in corresponding module-slot of the device. 1 None No module inserted 2 Rps A RPS module is inserted 254 unknown value 255 unsupported variable for addressed device For details of the module (connector sub-types, ...) the fabrication data has to evaluated
| ||||
| CcmroHtuFarClkFabData | 1.3.6.1.4.1.1887.1.1.4.3.1.2.1.16 | DisplayString (SIZE (20)) | RO | mandatory |
column · DisplayString (SIZE (20)) · read-only · mandatory Fabrication Data of Clock and Alarm Module | ||||
| CcmroHtuFarClkType | 1.3.6.1.4.1.1887.1.1.4.3.1.2.1.17 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Type of Clock and Alarm Module in corresponding module-slot of the device. 1 None No module inserted 2 ClockAlarm A combined Clock and Alarm module is inserted 3 Clock A Clock module is inserted 3 Alarm An Alarm module is inserted 254 unknown value 255 unsupported variable for addressed device For details of the module (connector sub-types, ...) the fabrication data has to evaluated
| ||||
| CcmroHtuFarDbgFabData | 1.3.6.1.4.1.1887.1.1.4.3.1.2.1.18 | DisplayString (SIZE (20)) | RO | mandatory |
column · DisplayString (SIZE (20)) · read-only · mandatory Fabrication Data of Debug-Module | ||||
| CcmroHtuFarDbgType | 1.3.6.1.4.1.1887.1.1.4.3.1.2.1.19 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Type of Debug-Module in corresponding module-slot of the device. 1 None No module inserted 2 Debug A Debug module is inserted 254 unknown value 255 unsupported variable for addressed device For details of the module (connector sub-types, ...) the fabrication data has to evaluated
| ||||
| CcmroHtuFarHousing | 1.3.6.1.4.1.1887.1.1.4.3.1.2.1.20 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Type of housing / installation of the device. 1 Rack The device is a line card to be installed in a sub-rack 2 Desktop The device is a desktop device 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroHtuFarRackVersion | 1.3.6.1.4.1.1887.1.1.4.3.1.2.1.21 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Version of the sub-rack in which the device is installed. 1 RackV1 The device is installed in a rack with V1 2 RackV2 The device is installed in a rack with V2 3 RackV3 The device is installed in a rack with V3 4 Desktop The device is a desktop device (and therefore not installed in a sub-rack) 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroHtuFarLtNtType | 1.3.6.1.4.1.1887.1.1.4.3.1.2.1.22 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether the device is configured as LT or NT. 1 LT The device is configured as LT 2 NT The device is configured as NT 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroHtuFarHdslChipset | 1.3.6.1.4.1.1887.1.1.4.3.1.2.1.23 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates which chipset the partner device uses for HDSL transmission 1 Level1 The partner device uses a Level 1 chipset 2 Metalink The partner device uses a MetaLink chipset 3 Infineon The partner device uses an Infineon chipset 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroHtuFarDipCfg | 1.3.6.1.4.1.1887.1.1.4.3.1.2.1.24 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether the device is configured through DIP Switches. 1 Disabled The device can be configured through management software 2 Enabled The device is configured by DIP switches 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroHtuFarEocCfg | 1.3.6.1.4.1.1887.1.1.4.3.1.2.1.25 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether the far device is reached by EOC or not. 1 Disabled The far device cannot be reached by EOC 2 Enabled The far device can be reached by EOC 3 Reg1 The EOC is up until the first regenerator section 4 Reg2 The EOC is up until the second regenerator section 5 Reg3 The EOC is up until the third regenerator section 6 Reg4 The EOC is up until the fourth regenerator section 7 Reg5 The EOC is up until the fifth regenerator section 8 Reg6 The EOC is up until the sixth regenerator section 9 Reg7 The EOC is up until the seventh regenerator section 10 Reg8 The EOC is up until the eighth regenerator section 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroHtuFarRpsVoltage | 1.3.6.1.4.1.1887.1.1.4.3.1.2.1.26 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates which Remote Power Supply (RPS) Voltage is being used by the device 1 V120 The RPS uses 120 Volts 2 V180 The RPS uses 180 Volts 3 NoRps The device is not equipped with an RPS 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroHtuFarPowerConfiguration | 1.3.6.1.4.1.1887.1.1.4.3.1.2.1.27 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates which kind of power supply is equiped 1 multifunctional No redundant supply possible 2 redundant Redundant supply possible 3 remoteFeeding Remote feeding possible 4 batteryDC DC-only supply 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroHtuFarIsdnFabData | 1.3.6.1.4.1.1887.1.1.4.3.1.2.1.28 | DisplayString (SIZE (20)) | RO | mandatory |
column · DisplayString (SIZE (20)) · read-only · mandatory Fabrication Data of ISDN-Module | ||||
| CcmroHtuFarIsdnType | 1.3.6.1.4.1.1887.1.1.4.3.1.2.1.29 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Type of ISDN-Module in corresponding module-slot of the device 1 None No module inserted 2 TE A module for S0(TE mode) operation is inserted 3 NT A module for S0(NT mode) operation is inserted 4 Uk0 A module for Uk0 operation is inserted 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroHtuFarTipRingReversal1 | 1.3.6.1.4.1.1887.1.1.4.3.1.2.1.30 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether tip-ring reversal has been detected and compensated for on the first wire pair 1 No Reversal not detected 2 Yes Reversal detected and compensated for 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroHtuFarTipRingReversal2 | 1.3.6.1.4.1.1887.1.1.4.3.1.2.1.31 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether tip-ring reversal has been detected and compensated for on the second wire pair 1 No Reversal not detected 2 Yes Reversal detected and compensated for 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroHtuFarTipRingReversal3 | 1.3.6.1.4.1.1887.1.1.4.3.1.2.1.32 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether tip-ring reversal has been detected and compensated for on the third wire pair 1 No Reversal not detected 2 Yes Reversal detected and compensated for 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroHtuFarTipRingReversal4 | 1.3.6.1.4.1.1887.1.1.4.3.1.2.1.33 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether tip-ring reversal has been detected and compensated for on the fourth wire pair 1 No Reversal not detected 2 Yes Reversal detected and compensated for 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroHtuFarPacketFabData | 1.3.6.1.4.1.1887.1.1.4.3.1.2.1.34 | DisplayString (SIZE (20)) | RO | mandatory |
column · DisplayString (SIZE (20)) · read-only · mandatory Fabrication Data of L2 Switch | ||||
| CcmroHtuFarPacketType | 1.3.6.1.4.1.1887.1.1.4.3.1.2.1.35 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Type of L2 Switch module. 1 None No module inserted 2 4P10/100 4-Port 10/100Base-T ethernet switch 3 1P10/100 1-Port 10/100Base-T ethernet switch 4 2P10/100 2-Port 10/100Base-T ethernet switch 5 3P10/100 3-Port 10/100Base-T ethernet switch 254 unknown value 255 unsupported variable for addressed device For details of the module (connector sub-types, ...) the fabrication data has to evaluated
| ||||
| CcmroHtuFarPacketMacAddr1 | 1.3.6.1.4.1.1887.1.1.4.3.1.2.1.36 | OCTET STRING (SIZE (6)) | RO | mandatory |
column · OCTET STRING (SIZE (6)) · read-only · mandatory MAC address of L2 ethernet switch. Value of Byte 0..5 Meaning 0x00 - 0xFD MAC address all 0xFE unknown value all 0xFF unsupported variable | ||||
| CcmroHtuFarDslChipset | 1.3.6.1.4.1.1887.1.1.4.3.1.2.1.37 | DisplayString (SIZE (20)) | RO | mandatory |
column · DisplayString (SIZE (20)) · read-only · mandatory Type of xDSL chipset | ||||
| CcmroHtuFarDslFwLoad | 1.3.6.1.4.1.1887.1.1.4.3.1.2.1.38 | DisplayString (SIZE (20)) | RO | mandatory |
column · DisplayString (SIZE (20)) · read-only · mandatory Type of firmware load of xDSL chipset | ||||
| CcmroHtuFarFpgaLoad | 1.3.6.1.4.1.1887.1.1.4.3.1.2.1.39 | DisplayString (SIZE (20)) | RO | mandatory |
column · DisplayString (SIZE (20)) · read-only · mandatory Type of FPGA load | ||||
| CcmroHtuFarEthWanChip | 1.3.6.1.4.1.1887.1.1.4.3.1.2.1.40 | DisplayString (SIZE (20)) | RO | mandatory |
column · DisplayString (SIZE (20)) · read-only · mandatory Type of WAN chip which connects L2 switch and xDSL link | ||||
| CcmroHtuFarSwitchChip | 1.3.6.1.4.1.1887.1.1.4.3.1.2.1.41 | DisplayString (SIZE (20)) | RO | mandatory |
column · DisplayString (SIZE (20)) · read-only · mandatory Type of Switch Chip | ||||
| CcmroHtuFarBootloaderVers | 1.3.6.1.4.1.1887.1.1.4.3.1.2.1.42 | DisplayString (SIZE (20)) | RO | mandatory |
column · DisplayString (SIZE (20)) · read-only · mandatory Version of firmware boot loader | ||||
| CcmroHtuFarSerialNumber | 1.3.6.1.4.1.1887.1.1.4.3.1.2.1.43 | DisplayString (SIZE (20)) | RO | mandatory |
column · DisplayString (SIZE (20)) · read-only · mandatory Serial number of device | ||||
| CcmroHtuFarHwManufacturingDate | 1.3.6.1.4.1.1887.1.1.4.3.1.2.1.44 | DisplayString | RO | mandatory |
column · DisplayString · read-only · mandatory Manufacturing Date of the motherboard | ||||
| CcmroHtuFarRpsManufacturingDate | 1.3.6.1.4.1.1887.1.1.4.3.1.2.1.45 | DisplayString | RO | mandatory |
column · DisplayString · read-only · mandatory Manufacturing Date of the RPS Module | ||||
| CcmroHtuFarClkManufacturingDate | 1.3.6.1.4.1.1887.1.1.4.3.1.2.1.46 | DisplayString | RO | mandatory |
column · DisplayString · read-only · mandatory Manufacturing Date of the Clock and Alarm Module | ||||
| CcmroHtuFarTManufacturingDate | 1.3.6.1.4.1.1887.1.1.4.3.1.2.1.47 | DisplayString | RO | mandatory |
column · DisplayString · read-only · mandatory Manufacturing Date of the 2Mbps Module | ||||
| CcmroHtuFarDManufacturingDate | 1.3.6.1.4.1.1887.1.1.4.3.1.2.1.48 | DisplayString | RO | mandatory |
column · DisplayString · read-only · mandatory Manufacturing Date of the Data Module | ||||
| CcmroHtuFarPacketManufacturingDate | 1.3.6.1.4.1.1887.1.1.4.3.1.2.1.49 | DisplayString | RO | mandatory |
column · DisplayString · read-only · mandatory Manufacturing Date of the Packet Module | ||||
| CcmroHtuFarL2SDriverVersion | 1.3.6.1.4.1.1887.1.1.4.3.1.2.1.50 | DisplayString | RO | mandatory |
column · DisplayString · read-only · mandatory L2 Switch Driver Version | ||||
| TcmroUsedTsTable | 1.3.6.1.4.1.1887.1.1.4.3.1.3 | NA | mandatory | |
| RcmroUsedTsEntry | 1.3.6.1.4.1.1887.1.1.4.3.1.3.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CcmroUsedTsPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.1.3.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CcmroUsedTsLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.1.3.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CcmroUsedTsAll | 1.3.6.1.4.1.1887.1.1.4.3.1.3.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether all timeslots are used or not. If all of them are used, cmroUsedTsMap will return 'allUsed' for all time slots. 1 true All time slots are being used (ignore cmroUsedTsMap) 2 false Not all time slots are being used, details in cmroUsedTsMap 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroUsedTsMap | 1.3.6.1.4.1.1887.1.1.4.3.1.3.1.4 | OCTET STRING (SIZE (32)) | RO | mandatory |
column · OCTET STRING (SIZE (32)) · read-only · mandatory If cmroUsedTsAll is 'false(2)' this variable reports which time slot in the E1 2Mbit/s signal is used for which purpose. The variable consists of an array with length 32. Each array position corresponds to a time slot in the E1 signal and its content indicates what the time slot is used for. The following codes are used: 1 N1 Used for G.703 signal 2 N2 Used for Data signal 3 FastSig1 Used for Fast Signalling in stream 1 4 FastSig2 Used for Fast Signalling in stream 2 5 CAS Used for CAS Signalling 6 Unused Time slot is unused 7 Sync Used for synchronisation (Time slot 0) 8 Ignore No mapping (cmroUsedTsAll is 'true') 254 unknown value 255 unsupported variable for addressed device | ||||
| CcmroUsedTsMapStuExtension | 1.3.6.1.4.1.1887.1.1.4.3.1.3.1.5 | OCTET STRING (SIZE (4)) | RO | mandatory |
column · OCTET STRING (SIZE (4)) · read-only · mandatory If cmroUsedTsAll is 'false(2)' this variable reports which time slot in the E1 2Mbit/s signal is used for which purpose. This variable describes the addidtional 4 timeslots which are available with the SDSL system. The 4 bytes in this variable correspond to the time slots 32..35. Each array position corresponds to a time slot in the E1 signal and its content indicates what the time slot is used for. The following codes are used: 1 N1 Used for G.703 signal 2 N2 Used for Data signal 3 FastSig1 Used for Fast Signalling in stream 1 4 FastSig2 Used for Fast Signalling in stream 2 5 CAS Used for CAS Signalling 6 Unused Time slot is unused 7 Sync Used for synchronisation (Time slot 0) 8 Ignore No mapping (cmroUsedTsAll is 'true') 254 unknown value 255 unsupported variable for addressed device | ||||
| TcmroOmiTable | 1.3.6.1.4.1.1887.1.1.4.3.1.4 | NA | mandatory | |
| RcmroOmiEntry | 1.3.6.1.4.1.1887.1.1.4.3.1.4.1 | NA | mandatory | |
row · not-accessible · mandatory
| ||||
| CcmroOmiPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.1.4.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CcmroOmiHwFabData | 1.3.6.1.4.1.1887.1.1.4.3.1.4.1.2 | DisplayString (SIZE (20)) | RO | mandatory |
column · DisplayString (SIZE (20)) · read-only · mandatory Hardware Fabrication Data | ||||
| CcmroOmiActFwVers | 1.3.6.1.4.1.1887.1.1.4.3.1.4.1.3 | DisplayString | RO | mandatory |
column · DisplayString · read-only · mandatory Version of active Firmware | ||||
| CcmroOmiPasBankState | 1.3.6.1.4.1.1887.1.1.4.3.1.4.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory State of passive firmware bank 1 Empty contains no firmware 2 Loaded contains a valid firmware 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroOmiPasFwVers | 1.3.6.1.4.1.1887.1.1.4.3.1.4.1.5 | DisplayString | RO | mandatory |
column · DisplayString · read-only · mandatory Version of passive firmware | ||||
| CcmroOmiRackVersion | 1.3.6.1.4.1.1887.1.1.4.3.1.4.1.6 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Version of the sub-rack in which the device is installed. 1 RackV1 The device is installed in a rack with V1 2 RackV2 The device is installed in a rack with V2 3 RackV3 The device is installed in a rack with V3 4 Desktop The device is a desktop device (and therefore not installed in a sub-rack) 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroOmiActFwType | 1.3.6.1.4.1.1887.1.1.4.3.1.4.1.7 | DisplayString | RO | mandatory |
column · DisplayString · read-only · mandatory Contains the firmware type of the active firmware | ||||
| CcmroOmiRackVersion2 | 1.3.6.1.4.1.1887.1.1.4.3.1.4.1.8 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Version of the sub-rack 2. 1 RackV1 rack with V1 2 RackV2 rack with V2 3 RackV3 rack with V3 4 Desktop desktop device (and therefore not installed in a sub-rack) 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroOmiRackVersion3 | 1.3.6.1.4.1.1887.1.1.4.3.1.4.1.9 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Version of the sub-rack 3. 1 RackV1 rack with V1 2 RackV2 rack with V2 3 RackV3 rack with V3 4 Desktop desktop device (and therefore not installed in a sub-rack) 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroOmiRackVersion4 | 1.3.6.1.4.1.1887.1.1.4.3.1.4.1.10 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Version of the sub-rack 4. 1 RackV1 rack with V1 2 RackV2 rack with V2 3 RackV3 rack with V3 4 Desktop desktop device (and therefore not installed in a sub-rack) 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroOmiCardLocation | 1.3.6.1.4.1.1887.1.1.4.3.1.4.1.11 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Card location in subrack: 0..254 | ||||
| CcmroOmiSeepromVers | 1.3.6.1.4.1.1887.1.1.4.3.1.4.1.12 | DisplayString (SIZE (3)) | RO | mandatory |
column · DisplayString (SIZE (3)) · read-only · mandatory Version of configuration data format | ||||
| CcmroOmiMCUSerialNo | 1.3.6.1.4.1.1887.1.1.4.3.1.4.1.13 | DisplayString (SIZE (5)) | RO | mandatory |
column · DisplayString (SIZE (5)) · read-only · mandatory Serial number of the device | ||||
| CcmroOmiPasFwType | 1.3.6.1.4.1.1887.1.1.4.3.1.4.1.14 | DisplayString (SIZE (5)) | RO | mandatory |
column · DisplayString (SIZE (5)) · read-only · mandatory Contains the firmware type of the passive firmware | ||||
| CcmroOmiBootLoaderVers | 1.3.6.1.4.1.1887.1.1.4.3.1.4.1.15 | DisplayString | RO | mandatory |
column · DisplayString · read-only · mandatory Contains the Boot loader version | ||||
| CcmroOmiMACAddress | 1.3.6.1.4.1.1887.1.1.4.3.1.4.1.16 | OCTET STRING (SIZE (6)) | RO | mandatory |
column · OCTET STRING (SIZE (6)) · read-only · mandatory Contains the MCU MAC address Value of Byte 0..5 Meaning 0x00 - 0xFD MAC address all 0xFE unknown value all 0xFF unsupported variable | ||||
| CcmroOmiNMSHwPartNo | 1.3.6.1.4.1.1887.1.1.4.3.1.4.1.17 | DisplayString (SIZE (20)) | RO | mandatory |
column · DisplayString (SIZE (20)) · read-only · mandatory Contains the Hw partition number | ||||
| CcmroOmiNMSChipPartNo | 1.3.6.1.4.1.1887.1.1.4.3.1.4.1.18 | DisplayString (SIZE (20)) | RO | mandatory |
column · DisplayString (SIZE (20)) · read-only · mandatory Contains the chip partition number | ||||
| CcmroOmiL2SMACAddress | 1.3.6.1.4.1.1887.1.1.4.3.1.4.1.19 | OCTET STRING (SIZE (6)) | RO | mandatory |
column · OCTET STRING (SIZE (6)) · read-only · mandatory Contains the MAC Address of L2 switch Value of Byte 0..5 Meaning 0x00 - 0xFD MAC address all 0xFE unknown value all 0xFF unsupported variable | ||||
| CcmroOmiL2SHwPartNo | 1.3.6.1.4.1.1887.1.1.4.3.1.4.1.20 | DisplayString (SIZE (20)) | RO | mandatory |
column · DisplayString (SIZE (20)) · read-only · mandatory Hardware partition number | ||||
| CcmroOmiL2SChipPartNo | 1.3.6.1.4.1.1887.1.1.4.3.1.4.1.21 | DisplayString (SIZE (20)) | RO | mandatory |
column · DisplayString (SIZE (20)) · read-only · mandatory Chip partition number | ||||
| CcmroOmiL2SFwVers | 1.3.6.1.4.1.1887.1.1.4.3.1.4.1.22 | DisplayString (SIZE (20)) | RO | mandatory |
column · DisplayString (SIZE (20)) · read-only · mandatory L2 Switch Firmware version | ||||
| CcmroOmiL2SFeatureFlags | 1.3.6.1.4.1.1887.1.1.4.3.1.4.1.23 | OCTET STRING (SIZE (128)) | RO | mandatory |
column · OCTET STRING (SIZE (128)) · read-only · mandatory L2 Switch partition feature flags | ||||
| CcmroOmiL2SModuleType | 1.3.6.1.4.1.1887.1.1.4.3.1.4.1.24 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory L2 Switch module type: 1 24 Fast Ethernet + 3GigaBit Ethernet, 254 NONE
| ||||
| CcmroOmiGBEHwPartNo | 1.3.6.1.4.1.1887.1.1.4.3.1.4.1.25 | DisplayString (SIZE (20)) | RO | mandatory |
column · DisplayString (SIZE (20)) · read-only · mandatory Gigabit ethernet Hw partition number | ||||
| CcmroOmiGBEModuleType | 1.3.6.1.4.1.1887.1.1.4.3.1.4.1.26 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Gigabit ethernet module type: 1 1000BASE-T copper, 254 NONE
| ||||
| CcmroOmiSFP1ModuleType | 1.3.6.1.4.1.1887.1.1.4.3.1.4.1.27 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory SFP module type. Enum type corresponding to accepted values in following two fields: 1 1000BASE-T copper, 2 1000BASE-SX short wavelength, 3 1000BASE-LX long wavelength, 254 NONE 255 UNKNOWN
| ||||
| CcmroOmiSFP1TranscType | 1.3.6.1.4.1.1887.1.1.4.3.1.4.1.28 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory SFP transceiver type (0..255) | ||||
| CcmroOmiSFP1TranscCode | 1.3.6.1.4.1.1887.1.1.4.3.1.4.1.29 | OCTET STRING (SIZE (8)) | RO | mandatory |
column · OCTET STRING (SIZE (8)) · read-only · mandatory SFP transceiver code: accepted values are those corresponding to module type | ||||
| CcmroOmiSFP1VendorName | 1.3.6.1.4.1.1887.1.1.4.3.1.4.1.30 | DisplayString (SIZE (16)) | RO | mandatory |
column · DisplayString (SIZE (16)) · read-only · mandatory SFP vendor name | ||||
| CcmroOmiSFP1VendorOUI | 1.3.6.1.4.1.1887.1.1.4.3.1.4.1.31 | OCTET STRING (SIZE (3)) | RO | mandatory |
column · OCTET STRING (SIZE (3)) · read-only · mandatory SFP IEEE company ID | ||||
| CcmroOmiSFP1VendorPartNo | 1.3.6.1.4.1.1887.1.1.4.3.1.4.1.32 | DisplayString (SIZE (16)) | RO | mandatory |
column · DisplayString (SIZE (16)) · read-only · mandatory SFP vendor partition number | ||||
| CcmroOmiSFP1VendorRevNo | 1.3.6.1.4.1.1887.1.1.4.3.1.4.1.33 | DisplayString (SIZE (4)) | RO | mandatory |
column · DisplayString (SIZE (4)) · read-only · mandatory SFP vendor revision number | ||||
| CcmroOmiSFP1VendorSerialNo | 1.3.6.1.4.1.1887.1.1.4.3.1.4.1.34 | DisplayString (SIZE (16)) | RO | mandatory |
column · DisplayString (SIZE (16)) · read-only · mandatory SFP vendor serial number | ||||
| CcmroOmiSFP1VendorDateCode | 1.3.6.1.4.1.1887.1.1.4.3.1.4.1.35 | OCTET STRING (SIZE (8)) | RO | mandatory |
column · OCTET STRING (SIZE (8)) · read-only · mandatory SFP vendor date code YYMMDDLL (LL=vendor specific lot code) | ||||
| CcmroOmiSFP2ModuleType | 1.3.6.1.4.1.1887.1.1.4.3.1.4.1.36 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory SFP module type. Enum type corresponding to accepted values in following two fields: 1 1000BASE-T copper, 2 1000BASE-SX short wavelength, 3 1000BASE-LX long wavelength, 254 NONE 255 UNKNOWN
| ||||
| CcmroOmiSFP2TranscType | 1.3.6.1.4.1.1887.1.1.4.3.1.4.1.37 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory SFP transceiver type (0..255) | ||||
| CcmroOmiSFP2TranscCode | 1.3.6.1.4.1.1887.1.1.4.3.1.4.1.38 | OCTET STRING (SIZE (8)) | RO | mandatory |
column · OCTET STRING (SIZE (8)) · read-only · mandatory SFP transceiver code: accepted values are those corresponding to module type | ||||
| CcmroOmiSFP2VendorName | 1.3.6.1.4.1.1887.1.1.4.3.1.4.1.39 | DisplayString (SIZE (16)) | RO | mandatory |
column · DisplayString (SIZE (16)) · read-only · mandatory SFP vendor name | ||||
| CcmroOmiSFP2VendorOUI | 1.3.6.1.4.1.1887.1.1.4.3.1.4.1.40 | OCTET STRING (SIZE (3)) | RO | mandatory |
column · OCTET STRING (SIZE (3)) · read-only · mandatory SFP IEEE company ID | ||||
| CcmroOmiSFP2VendorPartNo | 1.3.6.1.4.1.1887.1.1.4.3.1.4.1.41 | DisplayString (SIZE (16)) | RO | mandatory |
column · DisplayString (SIZE (16)) · read-only · mandatory SFP vendor partition number | ||||
| CcmroOmiSFP2VendorRevNo | 1.3.6.1.4.1.1887.1.1.4.3.1.4.1.42 | DisplayString (SIZE (4)) | RO | mandatory |
column · DisplayString (SIZE (4)) · read-only · mandatory SFP vendor revision number | ||||
| CcmroOmiSFP2VendorSerialNo | 1.3.6.1.4.1.1887.1.1.4.3.1.4.1.43 | DisplayString (SIZE (16)) | RO | mandatory |
column · DisplayString (SIZE (16)) · read-only · mandatory SFP vendor serial number | ||||
| CcmroOmiSFP2VendorDateCode | 1.3.6.1.4.1.1887.1.1.4.3.1.4.1.44 | OCTET STRING (SIZE (8)) | RO | mandatory |
column · OCTET STRING (SIZE (8)) · read-only · mandatory SFP vendor date code YYMMDDLL (LL=vendor specific lot code) | ||||
| CcmroOmiCESHwPartNo | 1.3.6.1.4.1.1887.1.1.4.3.1.4.1.45 | DisplayString (SIZE (20)) | RO | mandatory |
column · DisplayString (SIZE (20)) · read-only · mandatory CES HW part number | ||||
| CcmroOmiCESType | 1.3.6.1.4.1.1887.1.1.4.3.1.4.1.46 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory CES type: 1 None No CES available 2 ThirtyTwoE1tcxo 32 x E1 with Temperature Compensated Crystal Oscillator 3 ThirtyTwoE1ocxo 32 x E1 with Oven Compensated Crystal Oscillator 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroOmiCESMACAddress | 1.3.6.1.4.1.1887.1.1.4.3.1.4.1.47 | OCTET STRING (SIZE (6)) | RO | mandatory |
column · OCTET STRING (SIZE (6)) · read-only · mandatory Contains the MAC Address of CES Value of Byte 0..5 Meaning 0x00 - 0xFD MAC address all 0xFE unknown value all 0xFF unsupported variable | ||||
| CcmroOmiCESSerialNo | 1.3.6.1.4.1.1887.1.1.4.3.1.4.1.48 | DisplayString (SIZE (5)) | RO | mandatory |
column · DisplayString (SIZE (5)) · read-only · mandatory Serial number of CES | ||||
| TcmroRegTable | 1.3.6.1.4.1.1887.1.1.4.3.1.5 | NA | mandatory | |
| RcmroRegEntry | 1.3.6.1.4.1.1887.1.1.4.3.1.5.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CcmroRegPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.1.5.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CcmroRegLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.1.5.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CcmroRegNumReg1 | 1.3.6.1.4.1.1887.1.1.4.3.1.5.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Number of Regenerators in HDSL Path 1. 1 None No Regenerators 2 One One Regenerator (A) 3 Two Two Regenerators (A and B) 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroRegNumReg2 | 1.3.6.1.4.1.1887.1.1.4.3.1.5.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Number of Regenerators in HDSL Path 2. 1 None No Regenerators 2 One One Regenerator (A) 3 Two Two Regenerators (A and B) 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroRegFabData1A | 1.3.6.1.4.1.1887.1.1.4.3.1.5.1.5 | DisplayString (SIZE (20)) | RO | mandatory |
column · DisplayString (SIZE (20)) · read-only · mandatory Fabrication Data of Regenerator Section A in HDSL Path 1 | ||||
| CcmroRegFwVers1A | 1.3.6.1.4.1.1887.1.1.4.3.1.5.1.6 | DisplayString | RO | mandatory |
column · DisplayString · read-only · mandatory Firmware Version of Regenerator Section A in HDSL Path 1 | ||||
| CcmroRegFabData2A | 1.3.6.1.4.1.1887.1.1.4.3.1.5.1.7 | DisplayString (SIZE (20)) | RO | mandatory |
column · DisplayString (SIZE (20)) · read-only · mandatory Fabrication Data of Regenerator Section A in HDSL Path 2 | ||||
| CcmroRegFwVers2A | 1.3.6.1.4.1.1887.1.1.4.3.1.5.1.8 | DisplayString | RO | mandatory |
column · DisplayString · read-only · mandatory Firmware Version of Regenerator Section A in HDSL Path 2 | ||||
| CcmroRegFabData1B | 1.3.6.1.4.1.1887.1.1.4.3.1.5.1.9 | DisplayString (SIZE (20)) | RO | mandatory |
column · DisplayString (SIZE (20)) · read-only · mandatory Fabrication Data of Regenerator Section B in HDSL Path 1 | ||||
| CcmroRegFwVers1B | 1.3.6.1.4.1.1887.1.1.4.3.1.5.1.10 | DisplayString | RO | mandatory |
column · DisplayString · read-only · mandatory Firmware Version of Regenerator Section B in HDSL Path 1 | ||||
| CcmroRegFabData2B | 1.3.6.1.4.1.1887.1.1.4.3.1.5.1.11 | DisplayString (SIZE (20)) | RO | mandatory |
column · DisplayString (SIZE (20)) · read-only · mandatory Fabrication Data of Regenerator Section B in HDSL Path 2 | ||||
| CcmroRegFwVers2B | 1.3.6.1.4.1.1887.1.1.4.3.1.5.1.12 | DisplayString | RO | mandatory |
column · DisplayString · read-only · mandatory Firmware Version of Regenerator Section B in HDSL Path 2 | ||||
| CcmroRegTipRingReversal1ALt | 1.3.6.1.4.1.1887.1.1.4.3.1.5.1.13 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Unused variable. Only used for compatibility reasons. Refer to cmroSruTipRingReversalLt and cmroSruTipRingReversalNt. 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroRegTipRingReversal1ANt | 1.3.6.1.4.1.1887.1.1.4.3.1.5.1.14 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Unused variable. Only used for compatibility reasons. Refer to cmroSruTipRingReversalLt and cmroSruTipRingReversalNt. 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroRegTipRingReversal2ALt | 1.3.6.1.4.1.1887.1.1.4.3.1.5.1.15 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Unused variable. Only used for compatibility reasons. Refer to cmroSruTipRingReversalLt and cmroSruTipRingReversalNt. 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroRegTipRingReversal2ANt | 1.3.6.1.4.1.1887.1.1.4.3.1.5.1.16 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Unused variable. Only used for compatibility reasons. Refer to cmroSruTipRingReversalLt and cmroSruTipRingReversalNt. 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroRegTipRingReversal1BLt | 1.3.6.1.4.1.1887.1.1.4.3.1.5.1.17 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Unused variable. Only used for compatibility reasons. Refer to cmroSruTipRingReversalLt and cmroSruTipRingReversalNt. 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroRegTipRingReversal1BNt | 1.3.6.1.4.1.1887.1.1.4.3.1.5.1.18 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Unused variable. Only used for compatibility reasons. Refer to cmroSruTipRingReversalLt and cmroSruTipRingReversalNt. 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroRegTipRingReversal2BLt | 1.3.6.1.4.1.1887.1.1.4.3.1.5.1.19 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Unused variable. Only used for compatibility reasons. Refer to cmroSruTipRingReversalLt and cmroSruTipRingReversalNt. 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroRegTipRingReversal2BNt | 1.3.6.1.4.1.1887.1.1.4.3.1.5.1.20 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Unused variable. Only used for compatibility reasons. Refer to cmroSruTipRingReversalLt and cmroSruTipRingReversalNt. 254 unknown value 255 unsupported variable for addressed device
| ||||
| TcmroSruTable | 1.3.6.1.4.1.1887.1.1.4.3.1.6 | NA | mandatory | |
| RcmroSruEntry | 1.3.6.1.4.1.1887.1.1.4.3.1.6.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CcmroSruPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.1.6.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CcmroSruLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.1.6.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CcmroSruRegIndex | 1.3.6.1.4.1.1887.1.1.4.3.1.6.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the regenerator device and is used as index for the other elements in the Table
| ||||
| CcmroSruFabData | 1.3.6.1.4.1.1887.1.1.4.3.1.6.1.5 | DisplayString (SIZE (20)) | RO | mandatory |
column · DisplayString (SIZE (20)) · read-only · mandatory Fabrication Data of Regenerator | ||||
| CcmroSruActFwType | 1.3.6.1.4.1.1887.1.1.4.3.1.6.1.6 | DisplayString | RO | mandatory |
column · DisplayString · read-only · mandatory Active firmware Type of Regenerator | ||||
| CcmroSruActFwVers | 1.3.6.1.4.1.1887.1.1.4.3.1.6.1.7 | DisplayString | RO | mandatory |
column · DisplayString · read-only · mandatory Active firmware Version of Regenerator | ||||
| CcmroSruPasBankState | 1.3.6.1.4.1.1887.1.1.4.3.1.6.1.8 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory State of passive firmware bank 1 Empty contains no firmware 2 Loaded contains a valid firmware 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroSruPasFwType | 1.3.6.1.4.1.1887.1.1.4.3.1.6.1.9 | DisplayString | RO | mandatory |
column · DisplayString · read-only · mandatory Passive firmware Type of Regenerator | ||||
| CcmroSruPasFwVers | 1.3.6.1.4.1.1887.1.1.4.3.1.6.1.10 | DisplayString | RO | mandatory |
column · DisplayString · read-only · mandatory Passive firmware Version of Regenerator | ||||
| CcmroSruTipRingReversalLt | 1.3.6.1.4.1.1887.1.1.4.3.1.6.1.11 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether tip-ring reversal has been detected and compensated for in direction of the LT 1 No Reversal not detected 2 Yes Reversal detected and compensated for 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroSruTipRingReversalNt | 1.3.6.1.4.1.1887.1.1.4.3.1.6.1.12 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether tip-ring reversal has been detected and compensated for in direction of the NT 1 No Reversal not detected 2 Yes Reversal detected and compensated for 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroSruRedundantlyPowered | 1.3.6.1.4.1.1887.1.1.4.3.1.6.1.13 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether the regenerator is being redundantly powered 1 No Regenerator is not being redundantly powered 2 Yes Regenerator is being redundantly powered 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroSruPowerPassThrough | 1.3.6.1.4.1.1887.1.1.4.3.1.6.1.14 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether the regenerator is passing power through to the next regenerator section. 1 No Regenerator is not passing through power 2 Yes Regenerator is passing through power 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroSruSerialNumber | 1.3.6.1.4.1.1887.1.1.4.3.1.6.1.15 | DisplayString (SIZE (20)) | RO | mandatory |
column · DisplayString (SIZE (20)) · read-only · mandatory Serial number of regenerator | ||||
| CcmroSruHwManufacturingDate | 1.3.6.1.4.1.1887.1.1.4.3.1.6.1.16 | DisplayString | RO | mandatory |
column · DisplayString · read-only · mandatory Manufacturing Date of the motherboard | ||||
| TcmroCardTokenTable | 1.3.6.1.4.1.1887.1.1.4.3.1.7 | NA | mandatory | |
| RcmroCardTokenEntry | 1.3.6.1.4.1.1887.1.1.4.3.1.7.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CcmroCardTokenPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.1.7.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CcmroCardTokenLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.1.7.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CcmroCardTokenResId1 | 1.3.6.1.4.1.1887.1.1.4.3.1.7.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates who is in posession of the reservation token for system one. 1 Available The token is free 2 Lineint The token is given to the LineIntegrator 3 Lct The token is given to the Local Craft Terminal (LCT) 254 unknown value 255 unsupported variable for the addressed device
| ||||
| CcmroCardTokenResId2 | 1.3.6.1.4.1.1887.1.1.4.3.1.7.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates who is in posession of the reservation token for system two. 1 Available The token is free 2 Lineint The token is given to the LineIntegrator 3 Lct The token is given to the Local Craft Terminal (LCT) 254 unknown value 255 unsupported variable for the addressed device
| ||||
| CcmroCardTokenResId3 | 1.3.6.1.4.1.1887.1.1.4.3.1.7.1.5 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates who is in posession of the reservation token for system three. 1 Available The token is free 2 Lineint The token is given to the LineIntegrator 3 Lct The token is given to the Local Craft Terminal (LCT) 254 unknown value 255 unsupported variable for the addressed device
| ||||
| CcmroCardTokenResId4 | 1.3.6.1.4.1.1887.1.1.4.3.1.7.1.6 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates who is in posession of the reservation token for system four. 1 Available The token is free 2 Lineint The token is given to the LineIntegrator 3 Lct The token is given to the Local Craft Terminal (LCT) 254 unknown value 255 unsupported variable for the addressed device
| ||||
| NcmroLocalInventory | 1.3.6.1.4.1.1887.1.1.4.3.1.8 | |||
| TcmroLocalInventoryFpTable | 1.3.6.1.4.1.1887.1.1.4.3.1.8.1 | NA | mandatory | |
| RcmroLocalInventoryFpEntry | 1.3.6.1.4.1.1887.1.1.4.3.1.8.1.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CcmroLocalInventoryFpPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.1.8.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CcmroLocalInventoryFpLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.1.8.1.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CcmroLocalInventoryFpModule1Type | 1.3.6.1.4.1.1887.1.1.4.3.1.8.1.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Type of Front Panel Module 1 1 None No module 2 DCE DCE module 3 DTE DTE module 4 10Base-T 10Base-T Ethernet module 5 ABAR Advanced Bridge and Router module 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroLocalInventoryFpModule2Type | 1.3.6.1.4.1.1887.1.1.4.3.1.8.1.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Type of Front Panel Module 2 1 None No module 2 DCE DCE module 3 DTE DTE module 4 10Base-T 10Base-T Ethernet module 5 ABAR Advanced Bridge and Router module 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroLocalInventoryFpModule3Type | 1.3.6.1.4.1.1887.1.1.4.3.1.8.1.1.5 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Type of Front Panel Module 3 1 None No module 2 DCE DCE module 3 DTE DTE module 4 10Base-T 10Base-T Ethernet module 5 ABAR Advanced Bridge and Router module 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroLocalInventoryFpModule4Type | 1.3.6.1.4.1.1887.1.1.4.3.1.8.1.1.6 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Type of Front Panel Module 4 1 None No module 2 DCE DCE module 3 DTE DTE module 4 10Base-T 10Base-T Ethernet module 5 ABAR Advanced Bridge and Router module 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroLocalInventoryFpModule5Type | 1.3.6.1.4.1.1887.1.1.4.3.1.8.1.1.7 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Type of Front Panel Module 5 1 None No module 2 DCE DCE module 3 DTE DTE module 4 10Base-T 10Base-T Ethernet module 5 ABAR Advanced Bridge and Router module 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroLocalInventoryFpModule6Type | 1.3.6.1.4.1.1887.1.1.4.3.1.8.1.1.8 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Type of Front Panel Module 6 1 None No module 2 DCE DCE module 3 DTE DTE module 4 10Base-T 10Base-T Ethernet module 5 ABAR Advanced Bridge and Router module 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroLocalInventoryFpModule1FabData | 1.3.6.1.4.1.1887.1.1.4.3.1.8.1.1.9 | DisplayString (SIZE (20)) | RO | mandatory |
column · DisplayString (SIZE (20)) · read-only · mandatory Fabrication Data of Front Panel Module 1 | ||||
| CcmroLocalInventoryFpModule2FabData | 1.3.6.1.4.1.1887.1.1.4.3.1.8.1.1.10 | DisplayString (SIZE (20)) | RO | mandatory |
column · DisplayString (SIZE (20)) · read-only · mandatory Fabrication Data of Front Panel Module 2 | ||||
| CcmroLocalInventoryFpModule3FabData | 1.3.6.1.4.1.1887.1.1.4.3.1.8.1.1.11 | DisplayString (SIZE (20)) | RO | mandatory |
column · DisplayString (SIZE (20)) · read-only · mandatory Fabrication Data of Front Panel Module 3 | ||||
| CcmroLocalInventoryFpModule4FabData | 1.3.6.1.4.1.1887.1.1.4.3.1.8.1.1.12 | DisplayString (SIZE (20)) | RO | mandatory |
column · DisplayString (SIZE (20)) · read-only · mandatory Fabrication Data of Front Panel Module 4 | ||||
| CcmroLocalInventoryFpModule5FabData | 1.3.6.1.4.1.1887.1.1.4.3.1.8.1.1.13 | DisplayString (SIZE (20)) | RO | mandatory |
column · DisplayString (SIZE (20)) · read-only · mandatory Fabrication Data of Front Panel Module 5 | ||||
| CcmroLocalInventoryFpModule6FabData | 1.3.6.1.4.1.1887.1.1.4.3.1.8.1.1.14 | DisplayString (SIZE (20)) | RO | mandatory |
column · DisplayString (SIZE (20)) · read-only · mandatory Fabrication Data of Front Panel Module 6 | ||||
| TcmroLocalInventoryInfoTable | 1.3.6.1.4.1.1887.1.1.4.3.1.8.2 | NA | mandatory | |
| RcmroLocalInventoryInfoEntry | 1.3.6.1.4.1.1887.1.1.4.3.1.8.2.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CcmroLocalInventoryInfoPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.1.8.2.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CcmroLocalInventoryInfoLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.1.8.2.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CcmroLocalInventoryInfoString1Type | 1.3.6.1.4.1.1887.1.1.4.3.1.8.2.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Type of InfoString 1 1 Empty InfoString is empty 2 DSL Chip InfoString is related to the DSL Chip 3 DSL Firmware Load InfoString is related to the DSL Firmware Load 4 FPGA Load InfoString is related to the FPGA Load 5 ETH WAN Chip InfoString is related to the Ethernet WAN Chip 5 L2S Chip InfoString is related to the Layer2 Switch Chip 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroLocalInventoryInfoString2Type | 1.3.6.1.4.1.1887.1.1.4.3.1.8.2.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Type of InfoString 2 1 Empty InfoString is empty 2 DSL Chip InfoString is related to the DSL Chip 3 DSL Firmware Load InfoString is related to the DSL Firmware Load 4 FPGA Load InfoString is related to the FPGA Load 5 ETH WAN Chip InfoString is related to the Ethernet WAN Chip 5 L2S Chip InfoString is related to the Layer2 Switch Chip 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroLocalInventoryInfoString3Type | 1.3.6.1.4.1.1887.1.1.4.3.1.8.2.1.5 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Type of InfoString 3 1 Empty InfoString is empty 2 DSL Chip InfoString is related to the DSL Chip 3 DSL Firmware Load InfoString is related to the DSL Firmware Load 4 FPGA Load InfoString is related to the FPGA Load 5 ETH WAN Chip InfoString is related to the Ethernet WAN Chip 5 L2S Chip InfoString is related to the Layer2 Switch Chip 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroLocalInventoryInfoString4Type | 1.3.6.1.4.1.1887.1.1.4.3.1.8.2.1.6 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Type of InfoString 4 1 Empty InfoString is empty 2 DSL Chip InfoString is related to the DSL Chip 3 DSL Firmware Load InfoString is related to the DSL Firmware Load 4 FPGA Load InfoString is related to the FPGA Load 5 ETH WAN Chip InfoString is related to the Ethernet WAN Chip 5 L2S Chip InfoString is related to the Layer2 Switch Chip 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroLocalInventoryInfoString5Type | 1.3.6.1.4.1.1887.1.1.4.3.1.8.2.1.7 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Type of InfoString 5 1 Empty InfoString is empty 2 DSL Chip InfoString is related to the DSL Chip 3 DSL Firmware Load InfoString is related to the DSL Firmware Load 4 FPGA Load InfoString is related to the FPGA Load 5 ETH WAN Chip InfoString is related to the Ethernet WAN Chip 5 L2S Chip InfoString is related to the Layer2 Switch Chip 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroLocalInventoryInfoString1 | 1.3.6.1.4.1.1887.1.1.4.3.1.8.2.1.8 | DisplayString (SIZE (25)) | RO | mandatory |
column · DisplayString (SIZE (25)) · read-only · mandatory InfoString 1 | ||||
| CcmroLocalInventoryInfoString2 | 1.3.6.1.4.1.1887.1.1.4.3.1.8.2.1.9 | DisplayString (SIZE (25)) | RO | mandatory |
column · DisplayString (SIZE (25)) · read-only · mandatory InfoString 2 | ||||
| CcmroLocalInventoryInfoString3 | 1.3.6.1.4.1.1887.1.1.4.3.1.8.2.1.10 | DisplayString (SIZE (25)) | RO | mandatory |
column · DisplayString (SIZE (25)) · read-only · mandatory InfoString 3 | ||||
| CcmroLocalInventoryInfoString4 | 1.3.6.1.4.1.1887.1.1.4.3.1.8.2.1.11 | DisplayString (SIZE (25)) | RO | mandatory |
column · DisplayString (SIZE (25)) · read-only · mandatory InfoString 4 | ||||
| CcmroLocalInventoryInfoString5 | 1.3.6.1.4.1.1887.1.1.4.3.1.8.2.1.12 | DisplayString (SIZE (25)) | RO | mandatory |
column · DisplayString (SIZE (25)) · read-only · mandatory InfoString 5 | ||||
| NcmroFarInventory | 1.3.6.1.4.1.1887.1.1.4.3.1.9 | |||
| TcmroFarInventoryFpTable | 1.3.6.1.4.1.1887.1.1.4.3.1.9.1 | NA | mandatory | |
| RcmroFarInventoryFpEntry | 1.3.6.1.4.1.1887.1.1.4.3.1.9.1.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CcmroFarInventoryFpPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.1.9.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CcmroFarInventoryFpLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.1.9.1.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CcmroFarInventoryFpModule1Type | 1.3.6.1.4.1.1887.1.1.4.3.1.9.1.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Type of Front Panel Module 1 1 None No module 2 DCE DCE module 3 DTE DTE module 4 10Base-T 10Base-T Ethernet module 5 ABAR Advanced Bridge and Router module 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroFarInventoryFpModule2Type | 1.3.6.1.4.1.1887.1.1.4.3.1.9.1.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Type of Front Panel Module 2 1 None No module 2 DCE DCE module 3 DTE DTE module 4 10Base-T 10Base-T Ethernet module 5 ABAR Advanced Bridge and Router module 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroFarInventoryFpModule3Type | 1.3.6.1.4.1.1887.1.1.4.3.1.9.1.1.5 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Type of Front Panel Module 3 1 None No module 2 DCE DCE module 3 DTE DTE module 4 10Base-T 10Base-T Ethernet module 5 ABAR Advanced Bridge and Router module 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroFarInventoryFpModule4Type | 1.3.6.1.4.1.1887.1.1.4.3.1.9.1.1.6 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Type of Front Panel Module 4 1 None No module 2 DCE DCE module 3 DTE DTE module 4 10Base-T 10Base-T Ethernet module 5 ABAR Advanced Bridge and Router module 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroFarInventoryFpModule5Type | 1.3.6.1.4.1.1887.1.1.4.3.1.9.1.1.7 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Type of Front Panel Module 5 1 None No module 2 DCE DCE module 3 DTE DTE module 4 10Base-T 10Base-T Ethernet module 5 ABAR Advanced Bridge and Router module 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroFarInventoryFpModule6Type | 1.3.6.1.4.1.1887.1.1.4.3.1.9.1.1.8 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Type of Front Panel Module 6 1 None No module 2 DCE DCE module 3 DTE DTE module 4 10Base-T 10Base-T Ethernet module 5 ABAR Advanced Bridge and Router module 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroFarInventoryFpModule1FabData | 1.3.6.1.4.1.1887.1.1.4.3.1.9.1.1.9 | DisplayString (SIZE (20)) | RO | mandatory |
column · DisplayString (SIZE (20)) · read-only · mandatory Fabrication Data of Front Panel Module 1 | ||||
| CcmroFarInventoryFpModule2FabData | 1.3.6.1.4.1.1887.1.1.4.3.1.9.1.1.10 | DisplayString (SIZE (20)) | RO | mandatory |
column · DisplayString (SIZE (20)) · read-only · mandatory Fabrication Data of Front Panel Module 2 | ||||
| CcmroFarInventoryFpModule3FabData | 1.3.6.1.4.1.1887.1.1.4.3.1.9.1.1.11 | DisplayString (SIZE (20)) | RO | mandatory |
column · DisplayString (SIZE (20)) · read-only · mandatory Fabrication Data of Front Panel Module 3 | ||||
| CcmroFarInventoryFpModule4FabData | 1.3.6.1.4.1.1887.1.1.4.3.1.9.1.1.12 | DisplayString (SIZE (20)) | RO | mandatory |
column · DisplayString (SIZE (20)) · read-only · mandatory Fabrication Data of Front Panel Module 4 | ||||
| CcmroFarInventoryFpModule5FabData | 1.3.6.1.4.1.1887.1.1.4.3.1.9.1.1.13 | DisplayString (SIZE (20)) | RO | mandatory |
column · DisplayString (SIZE (20)) · read-only · mandatory Fabrication Data of Front Panel Module 5 | ||||
| CcmroFarInventoryFpModule6FabData | 1.3.6.1.4.1.1887.1.1.4.3.1.9.1.1.14 | DisplayString (SIZE (20)) | RO | mandatory |
column · DisplayString (SIZE (20)) · read-only · mandatory Fabrication Data of Front Panel Module 6 | ||||
| TcmroFarInventoryInfoTable | 1.3.6.1.4.1.1887.1.1.4.3.1.9.2 | NA | mandatory | |
| RcmroFarInventoryInfoEntry | 1.3.6.1.4.1.1887.1.1.4.3.1.9.2.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CcmroFarInventoryInfoPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.1.9.2.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CcmroFarInventoryInfoLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.1.9.2.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CcmroFarInventoryInfoString1Type | 1.3.6.1.4.1.1887.1.1.4.3.1.9.2.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Type of InfoString 1 1 Empty InfoString is empty 2 DSL Chip InfoString is related to the DSL Chip 3 DSL Firmware Load InfoString is related to the DSL Firmware Load 4 FPGA Load InfoString is related to the FPGA Load 5 ETH WAN Chip InfoString is related to the Ethernet WAN Chip 5 L2S Chip InfoString is related to the Layer2 Switch Chip 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroFarInventoryInfoString2Type | 1.3.6.1.4.1.1887.1.1.4.3.1.9.2.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Type of InfoString 2 1 Empty InfoString is empty 2 DSL Chip InfoString is related to the DSL Chip 3 DSL Firmware Load InfoString is related to the DSL Firmware Load 4 FPGA Load InfoString is related to the FPGA Load 5 ETH WAN Chip InfoString is related to the Ethernet WAN Chip 5 L2S Chip InfoString is related to the Layer2 Switch Chip 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroFarInventoryInfoString3Type | 1.3.6.1.4.1.1887.1.1.4.3.1.9.2.1.5 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Type of InfoString 3 1 Empty InfoString is empty 2 DSL Chip InfoString is related to the DSL Chip 3 DSL Firmware Load InfoString is related to the DSL Firmware Load 4 FPGA Load InfoString is related to the FPGA Load 5 ETH WAN Chip InfoString is related to the Ethernet WAN Chip 5 L2S Chip InfoString is related to the Layer2 Switch Chip 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroFarInventoryInfoString4Type | 1.3.6.1.4.1.1887.1.1.4.3.1.9.2.1.6 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Type of InfoString 4 1 Empty InfoString is empty 2 DSL Chip InfoString is related to the DSL Chip 3 DSL Firmware Load InfoString is related to the DSL Firmware Load 4 FPGA Load InfoString is related to the FPGA Load 5 ETH WAN Chip InfoString is related to the Ethernet WAN Chip 5 L2S Chip InfoString is related to the Layer2 Switch Chip 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroFarInventoryInfoString5Type | 1.3.6.1.4.1.1887.1.1.4.3.1.9.2.1.7 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Type of InfoString 5 1 Empty InfoString is empty 2 DSL Chip InfoString is related to the DSL Chip 3 DSL Firmware Load InfoString is related to the DSL Firmware Load 4 FPGA Load InfoString is related to the FPGA Load 5 ETH WAN Chip InfoString is related to the Ethernet WAN Chip 5 L2S Chip InfoString is related to the Layer2 Switch Chip 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroFarInventoryInfoString1 | 1.3.6.1.4.1.1887.1.1.4.3.1.9.2.1.8 | DisplayString (SIZE (25)) | RO | mandatory |
column · DisplayString (SIZE (25)) · read-only · mandatory InfoString 1 | ||||
| CcmroFarInventoryInfoString2 | 1.3.6.1.4.1.1887.1.1.4.3.1.9.2.1.9 | DisplayString (SIZE (25)) | RO | mandatory |
column · DisplayString (SIZE (25)) · read-only · mandatory InfoString 2 | ||||
| CcmroFarInventoryInfoString3 | 1.3.6.1.4.1.1887.1.1.4.3.1.9.2.1.10 | DisplayString (SIZE (25)) | RO | mandatory |
column · DisplayString (SIZE (25)) · read-only · mandatory InfoString 3 | ||||
| CcmroFarInventoryInfoString4 | 1.3.6.1.4.1.1887.1.1.4.3.1.9.2.1.11 | DisplayString (SIZE (25)) | RO | mandatory |
column · DisplayString (SIZE (25)) · read-only · mandatory InfoString 4 | ||||
| CcmroFarInventoryInfoString5 | 1.3.6.1.4.1.1887.1.1.4.3.1.9.2.1.12 | DisplayString (SIZE (25)) | RO | mandatory |
column · DisplayString (SIZE (25)) · read-only · mandatory InfoString 5 | ||||
| NcmroSruInventory | 1.3.6.1.4.1.1887.1.1.4.3.1.10 | |||
| TcmroSruInventoryInfoTable | 1.3.6.1.4.1.1887.1.1.4.3.1.10.1 | NA | mandatory | |
| RcmroSruInventoryInfoEntry | 1.3.6.1.4.1.1887.1.1.4.3.1.10.1.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CcmroSruInventoryInfoPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.1.10.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CcmroSruInventoryInfoLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.1.10.1.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CcmroSruInventoryInfoRegIndex | 1.3.6.1.4.1.1887.1.1.4.3.1.10.1.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the regenerator device and is used as index for the other elements in the Table
| ||||
| CcmroSruInventoryInfoString1Type | 1.3.6.1.4.1.1887.1.1.4.3.1.10.1.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Type of InfoString 1 1 Empty InfoString is empty 2 DSL Chip InfoString is related to the DSL Chip 3 DSL Firmware Load InfoString is related to the DSL Firmware Load 4 FPGA Load InfoString is related to the FPGA Load 5 ETH WAN Chip InfoString is related to the Ethernet WAN Chip 5 L2S Chip InfoString is related to the Layer2 Switch Chip 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroSruInventoryInfoString2Type | 1.3.6.1.4.1.1887.1.1.4.3.1.10.1.1.5 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Type of InfoString 2 1 Empty InfoString is empty 2 DSL Chip InfoString is related to the DSL Chip 3 DSL Firmware Load InfoString is related to the DSL Firmware Load 4 FPGA Load InfoString is related to the FPGA Load 5 ETH WAN Chip InfoString is related to the Ethernet WAN Chip 5 L2S Chip InfoString is related to the Layer2 Switch Chip 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroSruInventoryInfoString3Type | 1.3.6.1.4.1.1887.1.1.4.3.1.10.1.1.6 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Type of InfoString 3 1 Empty InfoString is empty 2 DSL Chip InfoString is related to the DSL Chip 3 DSL Firmware Load InfoString is related to the DSL Firmware Load 4 FPGA Load InfoString is related to the FPGA Load 5 ETH WAN Chip InfoString is related to the Ethernet WAN Chip 5 L2S Chip InfoString is related to the Layer2 Switch Chip 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroSruInventoryInfoString4Type | 1.3.6.1.4.1.1887.1.1.4.3.1.10.1.1.7 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Type of InfoString 4 1 Empty InfoString is empty 2 DSL Chip InfoString is related to the DSL Chip 3 DSL Firmware Load InfoString is related to the DSL Firmware Load 4 FPGA Load InfoString is related to the FPGA Load 5 ETH WAN Chip InfoString is related to the Ethernet WAN Chip 5 L2S Chip InfoString is related to the Layer2 Switch Chip 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroSruInventoryInfoString5Type | 1.3.6.1.4.1.1887.1.1.4.3.1.10.1.1.8 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Type of InfoString 5 1 Empty InfoString is empty 2 DSL Chip InfoString is related to the DSL Chip 3 DSL Firmware Load InfoString is related to the DSL Firmware Load 4 FPGA Load InfoString is related to the FPGA Load 5 ETH WAN Chip InfoString is related to the Ethernet WAN Chip 5 L2S Chip InfoString is related to the Layer2 Switch Chip 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmroSruInventoryInfoString1 | 1.3.6.1.4.1.1887.1.1.4.3.1.10.1.1.9 | DisplayString (SIZE (25)) | RO | mandatory |
column · DisplayString (SIZE (25)) · read-only · mandatory InfoString 1 | ||||
| CcmroSruInventoryInfoString2 | 1.3.6.1.4.1.1887.1.1.4.3.1.10.1.1.10 | DisplayString (SIZE (25)) | RO | mandatory |
column · DisplayString (SIZE (25)) · read-only · mandatory InfoString 2 | ||||
| CcmroSruInventoryInfoString3 | 1.3.6.1.4.1.1887.1.1.4.3.1.10.1.1.11 | DisplayString (SIZE (25)) | RO | mandatory |
column · DisplayString (SIZE (25)) · read-only · mandatory InfoString 3 | ||||
| CcmroSruInventoryInfoString4 | 1.3.6.1.4.1.1887.1.1.4.3.1.10.1.1.12 | DisplayString (SIZE (25)) | RO | mandatory |
column · DisplayString (SIZE (25)) · read-only · mandatory InfoString 4 | ||||
| CcmroSruInventoryInfoString5 | 1.3.6.1.4.1.1887.1.1.4.3.1.10.1.1.13 | DisplayString (SIZE (25)) | RO | mandatory |
column · DisplayString (SIZE (25)) · read-only · mandatory InfoString 5 | ||||
| Ncmrw | 1.3.6.1.4.1.1887.1.1.4.3.2 | |||
| NcmrwLocal | 1.3.6.1.4.1.1887.1.1.4.3.2.1 | |||
| TcmrwLocalTokenTable | 1.3.6.1.4.1.1887.1.1.4.3.2.1.1 | NA | mandatory | |
| RcmrwLocalTokenEntry | 1.3.6.1.4.1.1887.1.1.4.3.2.1.1.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CcmrwLocalTokenPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.1.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CcmrwLocalTokenLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.1.1.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CcmrwLocalTokenResId | 1.3.6.1.4.1.1887.1.1.4.3.2.1.1.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates who is in posession of the reservation token for this device. 1 Available The token is free 2 Lineint The token is given to the LineIntegrator 3 Lct The token is given to the Local Craft Terminal (LCT) 254 unknown value 255 unsupported variable for the addressed device
| ||||
| CcmrwLocalTokenDipLt | 1.3.6.1.4.1.1887.1.1.4.3.2.1.1.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether the LT is configured by DIP switch. If it is, then software configuration is not possible. 1 Inactive The LT is not configured by DIP switch 2 Active The LT is configured by DIP switch 3 NotLt The management system is connected to an NT locally 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CcmrwLocalTokenDipNt | 1.3.6.1.4.1.1887.1.1.4.3.2.1.1.1.5 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether the NT is configured by DIP switch. If it is, then software configuration is not possible. 1 Inactive The NT is not configured by DIP switch 2 Active The NT is configured by DIP switch 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CcmrwLocalTokenEoc | 1.3.6.1.4.1.1887.1.1.4.3.2.1.1.1.6 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether there is an EOC connection between the LT and the NT over the HDSL link. 1 Inactive EOC connection not available 2 Active EOC connection available 3 Reg1 The EOC is up until the first regenerator section 4 Reg2 The EOC is up until the second regenerator section 5 Reg3 The EOC is up until the third regenerator section 6 Reg4 The EOC is up until the fourth regenerator section 7 Reg5 The EOC is up until the fifth regenerator section 8 Reg6 The EOC is up until the sixth regenerator section 9 Reg7 The EOC is up until the seventh regenerator section 10 Reg8 The EOC is up until the eighth regenerator section 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CcmrwLocalTokenTicket | 1.3.6.1.4.1.1887.1.1.4.3.2.1.1.1.7 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Is used to request or refresh the token device. 1-10 Token1-10 The token was granted/refreshed, the index helps to detect whether it has expried since last reading from this variable 11 NotGranted The token was not granted 12 Lost The token could not be refreshed 13 NotRequested The token has not been requested 254 unknown value 255 unsupported variable for the addressed device
| ||||
| CcmrwLocalTokenRelease | 1.3.6.1.4.1.1887.1.1.4.3.2.1.1.1.8 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Is used to release the token device. 1 TokenReleased Token has been successfully released. 2 NoNeedToRelease Token was not reserved, so need to release. 3 NotReleased Granted to LCT and coudn`t been released. 254 unknown value 255 unsupported variable for the addressed device
| ||||
| CcmrwLocalTokenSessionId | 1.3.6.1.4.1.1887.1.1.4.3.2.1.1.1.9 | INTEGER (0..65535) | RW | mandatory |
column · INTEGER (0..65535) · read-write · mandatory Indicates which SNMP management is in posession of the reservation token for this device. 0 Invalid The session value is invalid 65535 Unsupported Unsupported variable for the addressed device | ||||
| TcmrwLocalCommonTable | 1.3.6.1.4.1.1887.1.1.4.3.2.1.2 | NA | mandatory | |
| RcmrwLocalCommonEntry | 1.3.6.1.4.1.1887.1.1.4.3.2.1.2.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CcmrwLocalCommonPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.1.2.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CcmrwLocalCommonLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.1.2.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CcmrwLocalCommonMode | 1.3.6.1.4.1.1887.1.1.4.3.2.1.2.1.3 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Defines the basic Mode the device is in. This has an influence on the default values of most configuration variables (if not overwritten) and on the limitations of options in the GUI of the element manager. 1 Transparent Transparent G.704 mode 2Mbit/s 2 Structured Structured 2Mbit/s mode (Framed) 3 Pra ISDN PRA mode 4 Data Standard Data-Data application 5 AddDrop Standard Add/Drop-Add/Drop application 6 TwoMData Standard 2Mbit/s-Data application 7 TwoMAddDrop Standard 2Mbit/s-Add/Drop application 8 Manual Manual mode (full freedom for configuration) 9 TiTwoM 2Mbit/s-Data application (TI style) 10 TiData Data-Data application 11 1TdmEth TDM-Ethernet application (TDM:DSL 1:1) 12 2TdmEth TDM-Ethernet application (TDM:DSL 1:2) 13 4TdmEth TDM-Ethernet application (TDM:DSL 1:4) 14 HalfTdmEth TDM-Ethernet application (TDM:DSL 2:1) 15 EthEth Ethernet application with 2 L2 Switches 16 DualE1 Dual E1 application 17 Mapped Mapped mode 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwLocalCommonFipo | 1.3.6.1.4.1.1887.1.1.4.3.2.1.2.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory FIPO Mode (Fractional Installation/Partial Operation). This allows the use of only one wire-pair with a reduced data rate of 960kbit/s (Fractional Installation) or the operation with two wire-pairs with fall-back to 960kbit/s if one wire-pair fails. 1 Normal Normal 2Mbit/s operation 2 Fractional Fractional Installation 3 Partial Partial Operation 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwLocalCommonRps | 1.3.6.1.4.1.1887.1.1.4.3.2.1.2.1.5 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Used to turn the Remote Power Supply on/off. 1 Inactive The RPS is turned off 2 Active The RPS is turned on 254 unknown value 255 unsupported
| ||||
| CcmrwLocalCommonTimeslotsU | 1.3.6.1.4.1.1887.1.1.4.3.2.1.2.1.6 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Bandwidth allocated for transmission interface (U-Interface) as a number of 64kbit/s time slots. When reading the following values can be returned: 1 bw64 Bandwidth 64 kbit/s 2 bw128 Bandwidth 128 kbit/s 3 bw192 Bandwidth 192 kbit/s 4 bw256 Bandwidth 256 kbit/s 5 bw320 Bandwidth 320 kbit/s 6 bw384 Bandwidth 384 kbit/s 7 bw448 Bandwidth 448 kbit/s 8 bw512 Bandwidth 512 kbit/s 9 bw576 Bandwidth 576 kbit/s 10 bw640 Bandwidth 640 kbit/s 11 bw704 Bandwidth 704 kbit/s 12 bw768 Bandwidth 768 kbit/s 13 bw832 Bandwidth 832 kbit/s 14 bw896 Bandwidth 896 kbit/s 15 bw960 Bandwidth 960 kbit/s 16 bw1024 Bandwidth 1024 kbit/s 17 bw1088 Bandwidth 1088 kbit/s 18 bw1152 Bandwidth 1152 kbit/s 19 bw1216 Bandwidth 1216 kbit/s 20 bw1280 Bandwidth 1280 kbit/s 21 bw1344 Bandwidth 1344 kbit/s 22 bw1408 Bandwidth 1408 kbit/s 23 bw1472 Bandwidth 1472 kbit/s 24 bw1536 Bandwidth 1536 kbit/s 25 bw1600 Bandwidth 1600 kbit/s 26 bw1664 Bandwidth 1664 kbit/s 27 bw1728 Bandwidth 1728 kbit/s 28 bw1792 Bandwidth 1792 kbit/s 29 bw1856 Bandwidth 1856 kbit/s 30 bw1920 Bandwidth 1920 kbit/s 31 bw1984 Bandwidth 1984 kbit/s 32 bw2048 Bandwidth 2048 kbit/s 33 bw2112 Bandwidth 2112 kbit/s 34 bw2176 Bandwidth 2176 kbit/s 35 bw2240 Bandwidth 2240 kbit/s 36 bw2304 Bandwidth 2304 kbit/s 37 bw2368 Bandwidth 2368 kbit/s 38 bw2432 Bandwidth 2432 kbit/s 39 bw2496 Bandwidth 2496 kbit/s 40 bw2560 Bandwidth 2560 kbit/s 41 bw2624 Bandwidth 2624 kbit/s 42 bw2688 Bandwidth 2688 kbit/s 43 bw2752 Bandwidth 2752 kbit/s 44 bw2816 Bandwidth 2816 kbit/s 45 bw2880 Bandwidth 2880 kbit/s 46 bw2944 Bandwidth 2944 kbit/s 47 bw3008 Bandwidth 3008 kbit/s 48 bw3072 Bandwidth 3072 kbit/s 49 bw3136 Bandwidth 3136 kbit/s 50 bw3200 Bandwidth 3200 kbit/s 51 bw3264 Bandwidth 3264 kbit/s 52 bw3328 Bandwidth 3328 kbit/s 53 bw3392 Bandwidth 3392 kbit/s 54 bw3456 Bandwidth 3456 kbit/s 55 bw3520 Bandwidth 3520 kbit/s 56 bw3584 Bandwidth 3584 kbit/s 57 bw3648 Bandwidth 3648 kbit/s 58 bw3712 Bandwidth 3712 kbit/s 59 bw3776 Bandwidth 3776 kbit/s 60 bw3840 Bandwidth 3840 kbit/s 61 bw3904 Bandwidth 3904 kbit/s 62 bw3968 Bandwidth 3968 kbit/s 63 bw4032 Bandwidth 4032 kbit/s 64 bw4096 Bandwidth 4096 kbit/s 65 bw4160 Bandwidth 4160 kbit/s 66 bw4224 Bandwidth 4224 kbit/s 67 bw4288 Bandwidth 4288 kbit/s 68 bw4352 Bandwidth 4352 kbit/s 69 bw4416 Bandwidth 4416 kbit/s 70 bw4480 Bandwidth 4480 kbit/s 71 bw4544 Bandwidth 4544 kbit/s 72 bw4608 Bandwidth 4608 kbit/s 73 bw4672 Bandwidth 4672 kbit/s 74 bw4736 Bandwidth 4736 kbit/s 75 bw4800 Bandwidth 4800 kbit/s 76 bw4864 Bandwidth 4864 kbit/s 77 bw4928 Bandwidth 4928 kbit/s 78 bw4992 Bandwidth 4992 kbit/s 79 bw5056 Bandwidth 5056 kbit/s 80 bw5120 Bandwidth 5120 kbit/s 81 bw5184 Bandwidth 5184 kbit/s 82 bw5248 Bandwidth 5248 kbit/s 83 bw5312 Bandwidth 5312 kbit/s 84 bw5376 Bandwidth 5376 kbit/s 85 bw5440 Bandwidth 5440 kbit/s 86 bw5504 Bandwidth 5504 kbit/s 87 bw5568 Bandwidth 5568 kbit/s 88 bw5632 Bandwidth 5632 kbit/s 89 bw5696 Bandwidth 5696 kbit/s 90 bw5760 Bandwidth 5760 kbit/s 91 bw5824 Bandwidth 5824 kbit/s 92 bw5888 Bandwidth 5888 kbit/s 93 bw5952 Bandwidth 5952 kbit/s 94 bw6016 Bandwidth 6016 kbit/s 95 bw6080 Bandwidth 6080 kbit/s 96 bw6144 Bandwidth 6144 kbit/s 97 bw6208 Bandwidth 6208 kbit/s 98 bw6272 Bandwidth 6272 kbit/s 99 bw6336 Bandwidth 6336 kbit/s 100 bw6400 Bandwidth 6400 kbit/s 101 bw6464 Bandwidth 6464 kbit/s 102 bw6528 Bandwidth 6528 kbit/s 103 bw6592 Bandwidth 6592 kbit/s 104 bw6656 Bandwidth 6656 kbit/s 105 bw6720 Bandwidth 6720 kbit/s 106 bw6784 Bandwidth 6784 kbit/s 107 bw6848 Bandwidth 6848 kbit/s 108 bw6912 Bandwidth 6912 kbit/s 109 bw6976 Bandwidth 6976 kbit/s 110 bw7040 Bandwidth 7040 kbit/s 111 bw7104 Bandwidth 7104 kbit/s 112 bw7168 Bandwidth 7168 kbit/s 113 bw7232 Bandwidth 7232 kbit/s 114 bw7296 Bandwidth 7296 kbit/s 115 bw7360 Bandwidth 7360 kbit/s 116 bw7424 Bandwidth 7424 kbit/s 117 bw7488 Bandwidth 7488 kbit/s 118 bw7552 Bandwidth 7552 kbit/s 119 bw7616 Bandwidth 7616 kbit/s 120 bw7680 Bandwidth 7680 kbit/s 121 bw7744 Bandwidth 7744 kbit/s 122 bw7808 Bandwidth 7808 kbit/s 123 bw7872 Bandwidth 7872 kbit/s 124 bw7936 Bandwidth 7936 kbit/s 125 bw8000 Bandwidth 8000 kbit/s 126 bw8064 Bandwidth 8064 kbit/s 127 bw8128 Bandwidth 8128 kbit/s 128 bw8192 Bandwidth 8192 kbit/s 129 bw8256 Bandwidth 8256 kbit/s 130 bw8320 Bandwidth 8320 kbit/s 131 bw8384 Bandwidth 8384 kbit/s 132 bw8448 Bandwidth 8448 kbit/s 133 bw8512 Bandwidth 8512 kbit/s 134 bw8576 Bandwidth 8576 kbit/s 135 bw8640 Bandwidth 8640 kbit/s 136 bw8704 Bandwidth 8704 kbit/s 137 bw8768 Bandwidth 8768 kbit/s 138 bw8832 Bandwidth 8832 kbit/s 139 bw8896 Bandwidth 8896 kbit/s 140 bw8960 Bandwidth 8960 kbit/s 141 bw9024 Bandwidth 9024 kbit/s 142 bw9088 Bandwidth 9088 kbit/s 143 bw9152 Bandwidth 9152 kbit/s 144 bw9216 Bandwidth 9216 kbit/s 145 bw9280 Bandwidth 9280 kbit/s 146 bw9344 Bandwidth 9344 kbit/s 147 bw9408 Bandwidth 9408 kbit/s 148 bw9472 Bandwidth 9472 kbit/s 149 bw9536 Bandwidth 9536 kbit/s 150 bw9600 Bandwidth 9600 kbit/s 151 bw9664 Bandwidth 9664 kbit/s 152 bw9728 Bandwidth 9728 kbit/s 153 bw9792 Bandwidth 9792 kbit/s 154 bw9856 Bandwidth 9856 kbit/s 155 bw9920 Bandwidth 9920 kbit/s 156 bw9984 Bandwidth 9984 kbit/s 157 bw10048 Bandwidth 10048 kbit/s 158 bw10112 Bandwidth 10112 kbit/s 159 bw10176 Bandwidth 10176 kbit/s 160 bw10240 Bandwidth 10240 kbit/s 161 bw10304 Bandwidth 10304 kbit/s 162 bw10368 Bandwidth 10368 kbit/s 163 bw10432 Bandwidth 10432 kbit/s 164 bw10496 Bandwidth 10496 kbit/s 165 bw10560 Bandwidth 10560 kbit/s 166 bw10624 Bandwidth 10624 kbit/s 167 bw10688 Bandwidth 10688 kbit/s 168 bw10752 Bandwidth 10752 kbit/s 169 bw10816 Bandwidth 10816 kbit/s 170 bw10880 Bandwidth 10880 kbit/s 171 bw10944 Bandwidth 10944 kbit/s 172 bw11008 Bandwidth 11008 kbit/s 173 bw11072 Bandwidth 11072 kbit/s 174 bw11136 Bandwidth 11136 kbit/s 175 bw11200 Bandwidth 11200 kbit/s 176 bw11264 Bandwidth 11264 kbit/s 177 bw11328 Bandwidth 11328 kbit/s 178 bw11392 Bandwidth 11392 kbit/s 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwLocalCommonClockMode | 1.3.6.1.4.1.1887.1.1.4.3.2.1.2.1.7 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Source for the clock out. 1 SystemClock The source is the system clock 2 ShdslClock The source is the SHDSL clock 3 SynchronousClock Clock Mode 3a (synchronous) 254 unknown value 255 unsupported
| ||||
| CcmrwLocalCommonMcsStructTdm | 1.3.6.1.4.1.1887.1.1.4.3.2.1.2.1.8 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Determines whether MCS framing for structured TDM networks is enabled or not. 1 Disabled Transparent TDM network 2 Enabled Structured TDM network (TS0) 254 unknown value 255 unsupported
| ||||
| CcmrwLocalCommonMcsChBandwidth | 1.3.6.1.4.1.1887.1.1.4.3.2.1.2.1.9 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Bandwidth allocated for all MCS channels as a number of 64kbit/s time slots. Between 1 and 89. When reading the following values can also be returned: 1 bw64 Bandwidth 64 kbit/s 2 bw128 Bandwidth 128 kbit/s 3 bw192 Bandwidth 192 kbit/s 4 bw256 Bandwidth 256 kbit/s 5 bw320 Bandwidth 320 kbit/s 6 bw384 Bandwidth 384 kbit/s 7 bw448 Bandwidth 448 kbit/s 8 bw512 Bandwidth 512 kbit/s 9 bw576 Bandwidth 576 kbit/s 10 bw640 Bandwidth 640 kbit/s 11 bw704 Bandwidth 704 kbit/s 12 bw768 Bandwidth 768 kbit/s 13 bw832 Bandwidth 832 kbit/s 14 bw896 Bandwidth 896 kbit/s 15 bw960 Bandwidth 960 kbit/s 16 bw1024 Bandwidth 1024 kbit/s 17 bw1088 Bandwidth 1088 kbit/s 18 bw1152 Bandwidth 1152 kbit/s 19 bw1216 Bandwidth 1216 kbit/s 20 bw1280 Bandwidth 1280 kbit/s 21 bw1344 Bandwidth 1344 kbit/s 22 bw1408 Bandwidth 1408 kbit/s 23 bw1472 Bandwidth 1472 kbit/s 24 bw1536 Bandwidth 1536 kbit/s 25 bw1600 Bandwidth 1600 kbit/s 26 bw1664 Bandwidth 1664 kbit/s 27 bw1728 Bandwidth 1728 kbit/s 28 bw1792 Bandwidth 1792 kbit/s 29 bw1856 Bandwidth 1856 kbit/s 30 bw1920 Bandwidth 1920 kbit/s 31 bw1984 Bandwidth 1984 kbit/s 32 bw2048 Bandwidth 2048 kbit/s 33 bw2112 Bandwidth 2112 kbit/s 34 bw2176 Bandwidth 2176 kbit/s 35 bw2240 Bandwidth 2240 kbit/s 36 bw2304 Bandwidth 2304 kbit/s 37 bw2368 Bandwidth 2368 kbit/s 38 bw2432 Bandwidth 2432 kbit/s 39 bw2496 Bandwidth 2496 kbit/s 40 bw2560 Bandwidth 2560 kbit/s 41 bw2624 Bandwidth 2624 kbit/s 42 bw2688 Bandwidth 2688 kbit/s 43 bw2752 Bandwidth 2752 kbit/s 44 bw2816 Bandwidth 2816 kbit/s 45 bw2880 Bandwidth 2880 kbit/s 46 bw2944 Bandwidth 2944 kbit/s 47 bw3008 Bandwidth 3008 kbit/s 48 bw3072 Bandwidth 3072 kbit/s 49 bw3136 Bandwidth 3136 kbit/s 50 bw3200 Bandwidth 3200 kbit/s 51 bw3264 Bandwidth 3264 kbit/s 52 bw3328 Bandwidth 3328 kbit/s 53 bw3392 Bandwidth 3392 kbit/s 54 bw3456 Bandwidth 3456 kbit/s 55 bw3520 Bandwidth 3520 kbit/s 56 bw3584 Bandwidth 3584 kbit/s 57 bw3648 Bandwidth 3648 kbit/s 58 bw3712 Bandwidth 3712 kbit/s 59 bw3776 Bandwidth 3776 kbit/s 60 bw3840 Bandwidth 3840 kbit/s 61 bw3904 Bandwidth 3904 kbit/s 62 bw3968 Bandwidth 3968 kbit/s 63 bw4032 Bandwidth 4032 kbit/s 64 bw4096 Bandwidth 4096 kbit/s 65 bw4160 Bandwidth 4160 kbit/s 66 bw4224 Bandwidth 4224 kbit/s 67 bw4288 Bandwidth 4288 kbit/s 68 bw4352 Bandwidth 4352 kbit/s 69 bw4416 Bandwidth 4416 kbit/s 70 bw4480 Bandwidth 4480 kbit/s 71 bw4544 Bandwidth 4544 kbit/s 72 bw4608 Bandwidth 4608 kbit/s 73 bw4672 Bandwidth 4672 kbit/s 74 bw4736 Bandwidth 4736 kbit/s 75 bw4800 Bandwidth 4800 kbit/s 76 bw4864 Bandwidth 4864 kbit/s 77 bw4928 Bandwidth 4928 kbit/s 78 bw4992 Bandwidth 4992 kbit/s 79 bw5056 Bandwidth 5056 kbit/s 80 bw5120 Bandwidth 5120 kbit/s 81 bw5184 Bandwidth 5184 kbit/s 82 bw5248 Bandwidth 5248 kbit/s 83 bw5312 Bandwidth 5312 kbit/s 84 bw5376 Bandwidth 5376 kbit/s 85 bw5440 Bandwidth 5440 kbit/s 86 bw5504 Bandwidth 5504 kbit/s 87 bw5568 Bandwidth 5568 kbit/s 88 bw5632 Bandwidth 5632 kbit/s 89 bw5696 Bandwidth 5696 kbit/s 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwLocalCommonRpsCurrent | 1.3.6.1.4.1.1887.1.1.4.3.2.1.2.1.10 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Indicates the Remote Power Supply current. 50 mA50 RPS current limied to 50 mA 60 mA60 RPS current limited to 60 mA 254 unknown value 255 unsupported
| ||||
| CcmrwLocalCommonLineModulation | 1.3.6.1.4.1.1887.1.1.4.3.2.1.2.1.11 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Indicates the Remote Power Supply current. 1 TC-PAM16 Line modulation TC-PAM16 2 TC-PAM32 Line modulation TC-PAM32 254 unknown value 255 unsupported
| ||||
| CcmrwLocalCommonUseFixTimeslotsU | 1.3.6.1.4.1.1887.1.1.4.3.2.1.2.1.12 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Enable or disable the fixed SHDSL Bitrate configured in cmrwLocalCommonFixTimeslotsU. 1 Disabled SHDSL Bitrate is not fixed 2 Enabled SHDSL Bitrate is fixed 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwLocalCommonFixTimeslotsU | 1.3.6.1.4.1.1887.1.1.4.3.2.1.2.1.13 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Fixed SHDSL Bitrate per Wire Pair (can be enabled by configuring cmrwLocalCommonUseFixTimeslotsU). When reading the following values can be returned: 1 bw64 Bandwidth 64 kbit/s 2 bw128 Bandwidth 128 kbit/s 3 bw192 Bandwidth 192 kbit/s 4 bw256 Bandwidth 256 kbit/s 5 bw320 Bandwidth 320 kbit/s 6 bw384 Bandwidth 384 kbit/s 7 bw448 Bandwidth 448 kbit/s 8 bw512 Bandwidth 512 kbit/s 9 bw576 Bandwidth 576 kbit/s 10 bw640 Bandwidth 640 kbit/s 11 bw704 Bandwidth 704 kbit/s 12 bw768 Bandwidth 768 kbit/s 13 bw832 Bandwidth 832 kbit/s 14 bw896 Bandwidth 896 kbit/s 15 bw960 Bandwidth 960 kbit/s 16 bw1024 Bandwidth 1024 kbit/s 17 bw1088 Bandwidth 1088 kbit/s 18 bw1152 Bandwidth 1152 kbit/s 19 bw1216 Bandwidth 1216 kbit/s 20 bw1280 Bandwidth 1280 kbit/s 21 bw1344 Bandwidth 1344 kbit/s 22 bw1408 Bandwidth 1408 kbit/s 23 bw1472 Bandwidth 1472 kbit/s 24 bw1536 Bandwidth 1536 kbit/s 25 bw1600 Bandwidth 1600 kbit/s 26 bw1664 Bandwidth 1664 kbit/s 27 bw1728 Bandwidth 1728 kbit/s 28 bw1792 Bandwidth 1792 kbit/s 29 bw1856 Bandwidth 1856 kbit/s 30 bw1920 Bandwidth 1920 kbit/s 31 bw1984 Bandwidth 1984 kbit/s 32 bw2048 Bandwidth 2048 kbit/s 33 bw2112 Bandwidth 2112 kbit/s 34 bw2176 Bandwidth 2176 kbit/s 35 bw2240 Bandwidth 2240 kbit/s 36 bw2304 Bandwidth 2304 kbit/s 37 bw2368 Bandwidth 2368 kbit/s 38 bw2432 Bandwidth 2432 kbit/s 39 bw2496 Bandwidth 2496 kbit/s 40 bw2560 Bandwidth 2560 kbit/s 41 bw2624 Bandwidth 2624 kbit/s 42 bw2688 Bandwidth 2688 kbit/s 43 bw2752 Bandwidth 2752 kbit/s 44 bw2816 Bandwidth 2816 kbit/s 45 bw2880 Bandwidth 2880 kbit/s 46 bw2944 Bandwidth 2944 kbit/s 47 bw3008 Bandwidth 3008 kbit/s 48 bw3072 Bandwidth 3072 kbit/s 49 bw3136 Bandwidth 3136 kbit/s 50 bw3200 Bandwidth 3200 kbit/s 51 bw3264 Bandwidth 3264 kbit/s 52 bw3328 Bandwidth 3328 kbit/s 53 bw3392 Bandwidth 3392 kbit/s 54 bw3456 Bandwidth 3456 kbit/s 55 bw3520 Bandwidth 3520 kbit/s 56 bw3584 Bandwidth 3584 kbit/s 57 bw3648 Bandwidth 3648 kbit/s 58 bw3712 Bandwidth 3712 kbit/s 59 bw3776 Bandwidth 3776 kbit/s 60 bw3840 Bandwidth 3840 kbit/s 61 bw3904 Bandwidth 3904 kbit/s 62 bw3968 Bandwidth 3968 kbit/s 63 bw4032 Bandwidth 4032 kbit/s 64 bw4096 Bandwidth 4096 kbit/s 65 bw4160 Bandwidth 4160 kbit/s 66 bw4224 Bandwidth 4224 kbit/s 67 bw4288 Bandwidth 4288 kbit/s 68 bw4352 Bandwidth 4352 kbit/s 69 bw4416 Bandwidth 4416 kbit/s 70 bw4480 Bandwidth 4480 kbit/s 71 bw4544 Bandwidth 4544 kbit/s 72 bw4608 Bandwidth 4608 kbit/s 73 bw4672 Bandwidth 4672 kbit/s 74 bw4736 Bandwidth 4736 kbit/s 75 bw4800 Bandwidth 4800 kbit/s 76 bw4864 Bandwidth 4864 kbit/s 77 bw4928 Bandwidth 4928 kbit/s 78 bw4992 Bandwidth 4992 kbit/s 79 bw5056 Bandwidth 5056 kbit/s 80 bw5120 Bandwidth 5120 kbit/s 81 bw5184 Bandwidth 5184 kbit/s 82 bw5248 Bandwidth 5248 kbit/s 83 bw5312 Bandwidth 5312 kbit/s 84 bw5376 Bandwidth 5376 kbit/s 85 bw5440 Bandwidth 5440 kbit/s 86 bw5504 Bandwidth 5504 kbit/s 87 bw5568 Bandwidth 5568 kbit/s 88 bw5632 Bandwidth 5632 kbit/s 89 bw5696 Bandwidth 5696 kbit/s 254 unknown value 255 unsupported variable for addressed device
| ||||
| TcmrwLocalClockTable | 1.3.6.1.4.1.1887.1.1.4.3.2.1.3 | NA | mandatory | |
| RcmrwLocalClockEntry | 1.3.6.1.4.1.1887.1.1.4.3.2.1.3.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CcmrwLocalClockPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.1.3.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CcmrwLocalClockLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.1.3.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CcmrwLocalClockActive | 1.3.6.1.4.1.1887.1.1.4.3.2.1.3.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates which clock source is currently being used. 1 T3In Uses Clock input T3In 2 TInterface Taking Clock from signal on T-Interface 3 UInterface Taking Clock from signal on U-Interface 4 Internal Using internal oscillator to generate Clock 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwLocalClockT3InAvailable | 1.3.6.1.4.1.1887.1.1.4.3.2.1.3.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Reports whether Clock Input T3In is available 1 False Clock Input T3In not available 2 True Clock Input T3In available 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwLocalClockTInterfaceAvailable | 1.3.6.1.4.1.1887.1.1.4.3.2.1.3.1.5 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Reports whether a clock signal can be derrived from the signal on the T-Interface 1 False Clock signal available 2 True Clock signal available 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwLocalClockUInterfaceAvailable | 1.3.6.1.4.1.1887.1.1.4.3.2.1.3.1.6 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Reports whether a clock signal can be derrived from the signal on the U-Interface 1 False Clock signal available 2 True Clock signal available 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwLocalClockInternalAvailable | 1.3.6.1.4.1.1887.1.1.4.3.2.1.3.1.7 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Reports whether the internal oscillator is available 1 False oscillator not available 2 True oscillator available 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwLocalClockPriority | 1.3.6.1.4.1.1887.1.1.4.3.2.1.3.1.8 | OCTET STRING (SIZE (4)) | RW | mandatory |
column · OCTET STRING (SIZE (4)) · read-write · mandatory Used to read and set the clock priority for the different clock sources. The variable is an array with length 4. The indices correspond to the priorities (0=highest, 3=lowest). The following values can be contained in each position, indicating which clock source has the corresponding priority: 1 T3In Clock Input T3In 2 TInterface Clock derrived from Signal at T-Interface 3 UInterface Clock derrived from Signal at U-Interface 4 Internal Internal oscillator 254 unknown value 255 unsupported variable for addressed device | ||||
| TcmrwLocal2MTable | 1.3.6.1.4.1.1887.1.1.4.3.2.1.4 | NA | mandatory | |
| RcmrwLocal2MEntry | 1.3.6.1.4.1.1887.1.1.4.3.2.1.4.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CcmrwLocal2MPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.1.4.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CcmrwLocal2MLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.1.4.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CcmrwLocal2MFraming | 1.3.6.1.4.1.1887.1.1.4.3.2.1.4.1.3 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Configures Frame Alignment 1 Transparent No frame or multi-frame synchronisation 2 Monitoring Frame and Multi-Frame synchronisation but no reinsertion of Frame 3 Termination Frame and Multi-Frame synchronisation and reinsertion 4 Channelized Frame and Multi-Frame synchronisation without transmission of timeslot 0 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwLocal2MEnableT | 1.3.6.1.4.1.1887.1.1.4.3.2.1.4.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Enable or disable the G.703 interface (T-Interface) 1 Disabled G.703 Interface is disabled 2 Enabled G.703 Interface is enabled 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwLocal2MTimeslotsT | 1.3.6.1.4.1.1887.1.1.4.3.2.1.4.1.5 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Bandwidth allocated for G.703 Interface (T-Interface) as a number of 64kbit/s time slots. Between 1 and 32. When reading the following values can also be returned: 1 bw64 Bandwidth 64 kbit/s 2 bw128 Bandwidth 128 kbit/s 3 bw192 Bandwidth 192 kbit/s 4 bw256 Bandwidth 256 kbit/s 5 bw320 Bandwidth 320 kbit/s 6 bw384 Bandwidth 384 kbit/s 7 bw448 Bandwidth 448 kbit/s 8 bw512 Bandwidth 512 kbit/s 9 bw576 Bandwidth 576 kbit/s 10 bw640 Bandwidth 640 kbit/s 11 bw704 Bandwidth 704 kbit/s 12 bw768 Bandwidth 768 kbit/s 13 bw832 Bandwidth 832 kbit/s 14 bw896 Bandwidth 896 kbit/s 15 bw960 Bandwidth 960 kbit/s 16 bw1024 Bandwidth 1024 kbit/s 17 bw1088 Bandwidth 1088 kbit/s 18 bw1152 Bandwidth 1152 kbit/s 19 bw1216 Bandwidth 1216 kbit/s 20 bw1280 Bandwidth 1280 kbit/s 21 bw1344 Bandwidth 1344 kbit/s 22 bw1408 Bandwidth 1408 kbit/s 23 bw1472 Bandwidth 1472 kbit/s 24 bw1536 Bandwidth 1536 kbit/s 25 bw1600 Bandwidth 1600 kbit/s 26 bw1664 Bandwidth 1664 kbit/s 27 bw1728 Bandwidth 1728 kbit/s 28 bw1792 Bandwidth 1792 kbit/s 29 bw1856 Bandwidth 1856 kbit/s 30 bw1920 Bandwidth 1920 kbit/s 31 bw1984 Bandwidth 1984 kbit/s 32 bw2048 Bandwidth 2048 kbit/s 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwLocal2MIdlecodeT | 1.3.6.1.4.1.1887.1.1.4.3.2.1.4.1.6 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Defines the Idle Code on the T-Interface. 1 AIS AIS 2 ES ES 3 PAIS PAIS 4 None No Idle Code 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwLocal2MCrc4T | 1.3.6.1.4.1.1887.1.1.4.3.2.1.4.1.7 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Defines whether CRC-4 evaluation at the T-Interface is done. 1 Off CRC-4 Data is not evaluated 2 On CRC-4 Data is evaluated, error if none present in signal 3 AutoOff CRC-4 Data is evaluated, if none is present, evaluation is disabled 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwLocal2MCrc4U | 1.3.6.1.4.1.1887.1.1.4.3.2.1.4.1.8 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Defines whether CRC-4 evaluation at the U-Interface is done. 1 Off CRC-4 Data is not evaluated 2 On CRC-4 Data is evaluated, error if none present in signal 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwLocal2MDetectAis | 1.3.6.1.4.1.1887.1.1.4.3.2.1.4.1.9 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Defines whether AIS detection is enabled or not 1 NoDetect AIS is not detected 2 Detect AIS is detected 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwLocal2MInsertAis | 1.3.6.1.4.1.1887.1.1.4.3.2.1.4.1.10 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Defines whether an AIS signal is regenerated or just passed through 1 NoInsertion Pass signal through 2 Insertion Regenerate signal 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwLocal2MSaBits | 1.3.6.1.4.1.1887.1.1.4.3.2.1.4.1.11 | OCTET STRING (SIZE (6)) | RW | mandatory |
column · OCTET STRING (SIZE (6)) · read-write · mandatory Contains the Sa-bit configuration. The variable is an array with length 6. The indicies address the Sa bits as follows: [0] Sa4 [1] Sa5 [2] Sa6 [3] Sa7 [4] Sa8 [5] Sa6 Loop Detection Positions 0,3 and 4 (Sa4, Sa7, Sa8) can contain the following values: 1 Transparent 2 Constant Ones Position 1 (Sa5) can contain the following values: 1 Transparent 2 Constant Ones 3 Insert Position 2 (Sa6) can contain the following values: 1 Transparent 2 Constant Ones 3 ETSI Norm 4 ANSI Norm Position 5 (Sa6 Loop Detection) can contain the following values: 1 Loop Detection Off 2 Loop Detection On All 6 positions can contain the values below: 254 unknown value 255 unsupported variable for addressed device | ||||
| CcmrwLocal2MTs16Signalling | 1.3.6.1.4.1.1887.1.1.4.3.2.1.4.1.12 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Defines whether time slot 16 is passed through transparently or whether it is reinsertet. 1 Transparent Passing through TS16 2 New Reinserting TS16 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwLocal2MIdlecodeU | 1.3.6.1.4.1.1887.1.1.4.3.2.1.4.1.13 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Defines the Idle Code on the U-Interface. 1 AIS AIS 2 ES ES 3 PAIS PAIS 4 none no Idle Code 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwLocal2MTs0Present | 1.3.6.1.4.1.1887.1.1.4.3.2.1.4.1.14 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Defines whether timeslot 0 (G.704 frame) is actually transmitted by the U interface. 1 No Timeslot 0 is re-inserted by receiver 2 Yes Timeslot 0 is actually sent 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwLocal2MCrc4V | 1.3.6.1.4.1.1887.1.1.4.3.2.1.4.1.15 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Defines whether CRC-4 evaluation at the V-Interfaces is done. 1 Off CRC-4 Data is not evaluated 2 On CRC-4 Data is evaluated, error if none present in signal 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwLocal2MInterfaceImpedance | 1.3.6.1.4.1.1887.1.1.4.3.2.1.4.1.16 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Indicates the impedance of the G.703 interface. 75 ohm75 The impedance of the G.703 interface is 75 Ohm. 120 ohm120 The impedance of the G.703 interface is 120 Ohm. 254 unknown value 255 unsupported variable for addressed device
| ||||
| TcmrwLocalDataTable | 1.3.6.1.4.1.1887.1.1.4.3.2.1.5 | NA | mandatory | |
| RcmrwLocalDataEntry | 1.3.6.1.4.1.1887.1.1.4.3.2.1.5.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CcmrwLocalDataPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.1.5.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CcmrwLocalDataLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.1.5.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CcmrwLocalDataEnabledD | 1.3.6.1.4.1.1887.1.1.4.3.2.1.5.1.3 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Defines whether the Data Interface is enabled or not. 1 Disabled Data Interface is disabled 2 Enabled Data Interface is enabled 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwLocalDataTimeslotsD | 1.3.6.1.4.1.1887.1.1.4.3.2.1.5.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Bandwidth allocated for Data (D-Interface) as a number of 64kbit/s time slots. When reading the following values can also be returned: 1 bw64 Bandwidth 64 kbit/s 2 bw128 Bandwidth 128 kbit/s 3 bw192 Bandwidth 192 kbit/s 4 bw256 Bandwidth 256 kbit/s 5 bw320 Bandwidth 320 kbit/s 6 bw384 Bandwidth 384 kbit/s 7 bw448 Bandwidth 448 kbit/s 8 bw512 Bandwidth 512 kbit/s 9 bw576 Bandwidth 576 kbit/s 10 bw640 Bandwidth 640 kbit/s 11 bw704 Bandwidth 704 kbit/s 12 bw768 Bandwidth 768 kbit/s 13 bw832 Bandwidth 832 kbit/s 14 bw896 Bandwidth 896 kbit/s 15 bw960 Bandwidth 960 kbit/s 16 bw1024 Bandwidth 1024 kbit/s 17 bw1088 Bandwidth 1088 kbit/s 18 bw1152 Bandwidth 1152 kbit/s 19 bw1216 Bandwidth 1216 kbit/s 20 bw1280 Bandwidth 1280 kbit/s 21 bw1344 Bandwidth 1344 kbit/s 22 bw1408 Bandwidth 1408 kbit/s 23 bw1472 Bandwidth 1472 kbit/s 24 bw1536 Bandwidth 1536 kbit/s 25 bw1600 Bandwidth 1600 kbit/s 26 bw1664 Bandwidth 1664 kbit/s 27 bw1728 Bandwidth 1728 kbit/s 28 bw1792 Bandwidth 1792 kbit/s 29 bw1856 Bandwidth 1856 kbit/s 30 bw1920 Bandwidth 1920 kbit/s 31 bw1984 Bandwidth 1984 kbit/s 32 bw2048 Bandwidth 2048 kbit/s 33 bw2112 Bandwidth 2112 kbit/s 34 bw2176 Bandwidth 2176 kbit/s 35 bw2240 Bandwidth 2240 kbit/s 36 bw2304 Bandwidth 2304 kbit/s 37 bw2368 Bandwidth 2368 kbit/s 38 bw2432 Bandwidth 2432 kbit/s 39 bw2496 Bandwidth 2496 kbit/s 40 bw2560 Bandwidth 2560 kbit/s 41 bw2624 Bandwidth 2624 kbit/s 42 bw2688 Bandwidth 2688 kbit/s 43 bw2752 Bandwidth 2752 kbit/s 44 bw2816 Bandwidth 2816 kbit/s 45 bw2880 Bandwidth 2880 kbit/s 46 bw2944 Bandwidth 2944 kbit/s 47 bw3008 Bandwidth 3008 kbit/s 48 bw3072 Bandwidth 3072 kbit/s 49 bw3136 Bandwidth 3136 kbit/s 50 bw3200 Bandwidth 3200 kbit/s 51 bw3264 Bandwidth 3264 kbit/s 52 bw3328 Bandwidth 3328 kbit/s 53 bw3392 Bandwidth 3392 kbit/s 54 bw3456 Bandwidth 3456 kbit/s 55 bw3520 Bandwidth 3520 kbit/s 56 bw3584 Bandwidth 3584 kbit/s 57 bw3648 Bandwidth 3648 kbit/s 58 bw3712 Bandwidth 3712 kbit/s 59 bw3776 Bandwidth 3776 kbit/s 60 bw3840 Bandwidth 3840 kbit/s 61 bw3904 Bandwidth 3904 kbit/s 62 bw3968 Bandwidth 3968 kbit/s 63 bw4032 Bandwidth 4032 kbit/s 64 bw4096 Bandwidth 4096 kbit/s 65 bw4160 Bandwidth 4160 kbit/s 66 bw4224 Bandwidth 4224 kbit/s 67 bw4288 Bandwidth 4288 kbit/s 68 bw4352 Bandwidth 4352 kbit/s 69 bw4416 Bandwidth 4416 kbit/s 70 bw4480 Bandwidth 4480 kbit/s 71 bw4544 Bandwidth 4544 kbit/s 72 bw4608 Bandwidth 4608 kbit/s 73 bw4672 Bandwidth 4672 kbit/s 74 bw4736 Bandwidth 4736 kbit/s 75 bw4800 Bandwidth 4800 kbit/s 76 bw4864 Bandwidth 4864 kbit/s 77 bw4928 Bandwidth 4928 kbit/s 78 bw4992 Bandwidth 4992 kbit/s 79 bw5056 Bandwidth 5056 kbit/s 80 bw5120 Bandwidth 5120 kbit/s 81 bw5184 Bandwidth 5184 kbit/s 82 bw5248 Bandwidth 5248 kbit/s 83 bw5312 Bandwidth 5312 kbit/s 84 bw5376 Bandwidth 5376 kbit/s 85 bw5440 Bandwidth 5440 kbit/s 86 bw5504 Bandwidth 5504 kbit/s 87 bw5568 Bandwidth 5568 kbit/s 88 bw5632 Bandwidth 5632 kbit/s 89 bw5696 Bandwidth 5696 kbit/s 90 bw5760 Bandwidth 5760 kbit/s 91 bw5824 Bandwidth 5824 kbit/s 92 bw5888 Bandwidth 5888 kbit/s 93 bw5952 Bandwidth 5952 kbit/s 94 bw6016 Bandwidth 6016 kbit/s 95 bw6080 Bandwidth 6080 kbit/s 96 bw6144 Bandwidth 6144 kbit/s 97 bw6208 Bandwidth 6208 kbit/s 98 bw6272 Bandwidth 6272 kbit/s 99 bw6336 Bandwidth 6336 kbit/s 100 bw6400 Bandwidth 6400 kbit/s 101 bw6464 Bandwidth 6464 kbit/s 102 bw6528 Bandwidth 6528 kbit/s 103 bw6592 Bandwidth 6592 kbit/s 104 bw6656 Bandwidth 6656 kbit/s 105 bw6720 Bandwidth 6720 kbit/s 106 bw6784 Bandwidth 6784 kbit/s 107 bw6848 Bandwidth 6848 kbit/s 108 bw6912 Bandwidth 6912 kbit/s 109 bw6976 Bandwidth 6976 kbit/s 110 bw7040 Bandwidth 7040 kbit/s 111 bw7104 Bandwidth 7104 kbit/s 112 bw7168 Bandwidth 7168 kbit/s 113 bw7232 Bandwidth 7232 kbit/s 114 bw7296 Bandwidth 7296 kbit/s 115 bw7360 Bandwidth 7360 kbit/s 116 bw7424 Bandwidth 7424 kbit/s 117 bw7488 Bandwidth 7488 kbit/s 118 bw7552 Bandwidth 7552 kbit/s 119 bw7616 Bandwidth 7616 kbit/s 120 bw7680 Bandwidth 7680 kbit/s 121 bw7744 Bandwidth 7744 kbit/s 122 bw7808 Bandwidth 7808 kbit/s 123 bw7872 Bandwidth 7872 kbit/s 124 bw7936 Bandwidth 7936 kbit/s 125 bw8000 Bandwidth 8000 kbit/s 126 bw8064 Bandwidth 8064 kbit/s 127 bw8128 Bandwidth 8128 kbit/s 128 bw8192 Bandwidth 8192 kbit/s 129 bw8256 Bandwidth 8256 kbit/s 130 bw8320 Bandwidth 8320 kbit/s 131 bw8384 Bandwidth 8384 kbit/s 132 bw8448 Bandwidth 8448 kbit/s 133 bw8512 Bandwidth 8512 kbit/s 134 bw8576 Bandwidth 8576 kbit/s 135 bw8640 Bandwidth 8640 kbit/s 136 bw8704 Bandwidth 8704 kbit/s 137 bw8768 Bandwidth 8768 kbit/s 138 bw8832 Bandwidth 8832 kbit/s 139 bw8896 Bandwidth 8896 kbit/s 140 bw8960 Bandwidth 8960 kbit/s 141 bw9024 Bandwidth 9024 kbit/s 142 bw9088 Bandwidth 9088 kbit/s 143 bw9152 Bandwidth 9152 kbit/s 144 bw9216 Bandwidth 9216 kbit/s 145 bw9280 Bandwidth 9280 kbit/s 146 bw9344 Bandwidth 9344 kbit/s 147 bw9408 Bandwidth 9408 kbit/s 148 bw9472 Bandwidth 9472 kbit/s 149 bw9536 Bandwidth 9536 kbit/s 150 bw9600 Bandwidth 9600 kbit/s 151 bw9664 Bandwidth 9664 kbit/s 152 bw9728 Bandwidth 9728 kbit/s 153 bw9792 Bandwidth 9792 kbit/s 154 bw9856 Bandwidth 9856 kbit/s 155 bw9920 Bandwidth 9920 kbit/s 156 bw9984 Bandwidth 9984 kbit/s 157 bw10048 Bandwidth 10048 kbit/s 158 bw10112 Bandwidth 10112 kbit/s 159 bw10176 Bandwidth 10176 kbit/s 160 bw10240 Bandwidth 10240 kbit/s 161 bw10304 Bandwidth 10304 kbit/s 162 bw10368 Bandwidth 10368 kbit/s 163 bw10432 Bandwidth 10432 kbit/s 164 bw10496 Bandwidth 10496 kbit/s 165 bw10560 Bandwidth 10560 kbit/s 166 bw10624 Bandwidth 10624 kbit/s 167 bw10688 Bandwidth 10688 kbit/s 168 bw10752 Bandwidth 10752 kbit/s 169 bw10816 Bandwidth 10816 kbit/s 170 bw10880 Bandwidth 10880 kbit/s 171 bw10944 Bandwidth 10944 kbit/s 172 bw11008 Bandwidth 11008 kbit/s 173 bw11072 Bandwidth 11072 kbit/s 174 bw11136 Bandwidth 11136 kbit/s 175 bw11200 Bandwidth 11200 kbit/s 176 bw11264 Bandwidth 11264 kbit/s 177 bw11328 Bandwidth 11328 kbit/s 178 bw11392 Bandwidth 11392 kbit/s 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwLocalDataIdlecodeD | 1.3.6.1.4.1.1887.1.1.4.3.2.1.5.1.5 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Defines the Idle Code for the Data Interface. 1 Null Always send 0 2 Ais Always send 1 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwLocalDataFastSig | 1.3.6.1.4.1.1887.1.1.4.3.2.1.5.1.6 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Defines whether Fast Signalling is used or not 1 Off Fast Signalling is not used 2 On Fast Signalling is used 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwLocalDataLine106 | 1.3.6.1.4.1.1887.1.1.4.3.2.1.5.1.7 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Defines whether control line 106 is set automatically or permanently turned on. 1 Auto Automatically set 2 Perm Permanently on 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwLocalDataLine107 | 1.3.6.1.4.1.1887.1.1.4.3.2.1.5.1.8 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Defines whether control line 107 is set automatically or permanently turned on. 1 Auto Automatically set 2 Perm Permanently on 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwLocalDataLine109 | 1.3.6.1.4.1.1887.1.1.4.3.2.1.5.1.9 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Defines whether control line 109 is set automatically or permanently turned on. 1 Auto Automatically set 2 Perm Permanently on 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwLocalDataLine140 | 1.3.6.1.4.1.1887.1.1.4.3.2.1.5.1.10 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Defines whether control line 140 is set automatically or permanently turned off. 1 Auto Automatically set 2 Perm Permanently off 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwLocalDataLine141 | 1.3.6.1.4.1.1887.1.1.4.3.2.1.5.1.11 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Defines whether control line 141 is set automatically or permanently turned off. 1 Auto Automatically set 2 Perm Permanently off 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwLocalDataUseTs16ForData | 1.3.6.1.4.1.1887.1.1.4.3.2.1.5.1.12 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Defines whether timeslot 16 can be used for data when no signalling information is transmitted in it. 1 No Timeslot 16 is reserved even if no signalling is used 2 Yes Timeslot 16 is used for data if no signalling is used 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwLocalDataEndToEndSignalling | 1.3.6.1.4.1.1887.1.1.4.3.2.1.5.1.13 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Defines whether End To End Signalling is enabled. 1 Disabled End To End Signalling is disabled 2 FastSig End To End Signalling is fast signalling 3 CAS End To End Signalling is CAS 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwLocalDataDteDceMode | 1.3.6.1.4.1.1887.1.1.4.3.2.1.5.1.14 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Defines the operation mode of the data interface. 1 DCE Data Interface operates in DCE (Data Circuit-Terminating Equipment) mode 2 DTE Data Interface operates in DTE (Data Terminal Equipment) mode 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwLocalDataIfSelector | 1.3.6.1.4.1.1887.1.1.4.3.2.1.5.1.15 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Selects the active data Interface. 1 mgblEthIf Manageable Ethernet Interface is selected 2 multiPurpDataIf Multi Purpose Data Interface is selected 254 unknown value 255 unsupported variable for addressed device
| ||||
| TcmrwLocalActionTable | 1.3.6.1.4.1.1887.1.1.4.3.2.1.6 | NA | mandatory | |
| RcmrwLocalActionEntry | 1.3.6.1.4.1.1887.1.1.4.3.2.1.6.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CcmrwLocalActionPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.1.6.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CcmrwLocalActionLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.1.6.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CcmrwLocalActionReboot | 1.3.6.1.4.1.1887.1.1.4.3.2.1.6.1.3 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Command to reboot device. The parameter specifies whether the firmware in the active or passive bank shall be started. 1 Passive Reboot using the passive firmware 2 Active Reboot using the active firmware 254 unknown value 255 unsupported variable for addressed device If the parameter 'passive' is specified but the passive firmware bank contains no valid code, the device reboots using the active firmware.
| ||||
| TcmrwLocalUserDataTable | 1.3.6.1.4.1.1887.1.1.4.3.2.1.7 | NA | mandatory | |
| RcmrwLocalUserDataEntry | 1.3.6.1.4.1.1887.1.1.4.3.2.1.7.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CcmrwLocalUserDataPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.1.7.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CcmrwLocalUserDataLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.1.7.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CcmrwLocalUserDataItemIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.1.7.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the data field number of the user data and is used as index for the other elements in the Table | ||||
| CcmrwLocalUserData | 1.3.6.1.4.1.1887.1.1.4.3.2.1.7.1.4 | DisplayString (SIZE (100)) | RW | mandatory |
column · DisplayString (SIZE (100)) · read-write · mandatory User data that can be written to the device | ||||
| TcmrwLocalPowerBackOffTable | 1.3.6.1.4.1.1887.1.1.4.3.2.1.8 | NA | mandatory | |
| RcmrwLocalPowerBackOffEntry | 1.3.6.1.4.1.1887.1.1.4.3.2.1.8.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CcmrwLocalPowerBackOffPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.1.8.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CcmrwLocalPowerBackOffLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.1.8.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CcmrwLocalPowerBackOffLevel | 1.3.6.1.4.1.1887.1.1.4.3.2.1.8.1.3 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Returns the configured power back off level 1 Db0 The configured level is 0 dB. 2 Db1 The configured level is 1 dB. 3 Db2 The configured level is 2 dB. 4 Db3 The configured level is 3 dB. 5 Db4 The configured level is 4 dB. 6 Db5 The configured level is 5 dB. 7 Db6 The configured level is 6 dB. 8 Db7 The configured level is 7 dB. 9 Db8 The configured level is 8 dB. 10 Db9 The configured level is 9 dB. 11 Db10 The configured level is 10 dB. 12 Db11 The configured level is 11 dB. 13 Db12 The configured level is 12 dB. 14 Db13 The configured level is 13 dB. 15 Db14 The configured level is 14 dB. 16 Db15 The configured level is 15 dB. 17 Db16 The configured level is 16 dB. 18 Db17 The configured level is 17 dB. 19 Db18 The configured level is 18 dB. 20 Db19 The configured level is 19 dB. 21 Db20 The configured level is 20 dB. 22 Db21 The configured level is 21 dB. 23 Db22 The configured level is 22 dB. 24 Db23 The configured level is 23 dB. 25 Db24 The configured level is 24 dB. 26 Db25 The configured level is 25 dB. 27 Db26 The configured level is 26 dB. 28 Db27 The configured level is 27 dB. 29 Db28 The configured level is 28 dB. 30 Db29 The configured level is 29 dB. 31 Db30 The configured level is 30 dB. 32 Db31 The configured level is 31 dB. 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwLocalPowerBackOffAutoEnable | 1.3.6.1.4.1.1887.1.1.4.3.2.1.8.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Reports whether auto power backoff is enabled 1 Off Auto power backoff is disabled 2 On Auto power backoff is enabled 254 unknown value 255 unsupported variable for addressed device
| ||||
| TcmrwLocalSectionPboTable | 1.3.6.1.4.1.1887.1.1.4.3.2.1.9 | NA | mandatory | |
| RcmrwLocalSectionPboEntry | 1.3.6.1.4.1.1887.1.1.4.3.2.1.9.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CcmrwLocalSectionPboPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.1.9.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CcmrwLocalSectionPboLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.1.9.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CcmrwLocalSectionPboSectionIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.1.9.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Selects the section for which the Power Back-off values are set.
| ||||
| CcmrwLocalSectionPboLevelLt | 1.3.6.1.4.1.1887.1.1.4.3.2.1.9.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Returns the configured power back off level 1 Db0 The configured level is 0 dB. 2 Db1 The configured level is 1 dB. 3 Db2 The configured level is 2 dB. 4 Db3 The configured level is 3 dB. 5 Db4 The configured level is 4 dB. 6 Db5 The configured level is 5 dB. 7 Db6 The configured level is 6 dB. 8 Db7 The configured level is 7 dB. 9 Db8 The configured level is 8 dB. 10 Db9 The configured level is 9 dB. 11 Db10 The configured level is 10 dB. 12 Db11 The configured level is 11 dB. 13 Db12 The configured level is 12 dB. 14 Db13 The configured level is 13 dB. 15 Db14 The configured level is 14 dB. 16 Db15 The configured level is 15 dB. 17 Db16 The configured level is 16 dB. 18 Db17 The configured level is 17 dB. 19 Db18 The configured level is 18 dB. 20 Db19 The configured level is 19 dB. 21 Db20 The configured level is 20 dB. 22 Db21 The configured level is 21 dB. 23 Db22 The configured level is 22 dB. 24 Db23 The configured level is 23 dB. 25 Db24 The configured level is 24 dB. 26 Db25 The configured level is 25 dB. 27 Db26 The configured level is 26 dB. 28 Db27 The configured level is 27 dB. 29 Db28 The configured level is 28 dB. 30 Db29 The configured level is 29 dB. 31 Db30 The configured level is 30 dB. 32 Db31 The configured level is 31 dB. 130 DbMin1 The configured level is -1 dB (Power Boost). 131 DbMin2 The configured level is -2 dB (Power Boost). 132 DbMin3 The configured level is -3 dB (Power Boost). 133 DbMin4 The configured level is -4 dB (Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwLocalSectionPboLevelNt | 1.3.6.1.4.1.1887.1.1.4.3.2.1.9.1.5 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Returns the configured power back off level 1 Db0 The configured level is 0 dB. 2 Db1 The configured level is 1 dB. 3 Db2 The configured level is 2 dB. 4 Db3 The configured level is 3 dB. 5 Db4 The configured level is 4 dB. 6 Db5 The configured level is 5 dB. 7 Db6 The configured level is 6 dB. 8 Db7 The configured level is 7 dB. 9 Db8 The configured level is 8 dB. 10 Db9 The configured level is 9 dB. 11 Db10 The configured level is 10 dB. 12 Db11 The configured level is 11 dB. 13 Db12 The configured level is 12 dB. 14 Db13 The configured level is 13 dB. 15 Db14 The configured level is 14 dB. 16 Db15 The configured level is 15 dB. 17 Db16 The configured level is 16 dB. 18 Db17 The configured level is 17 dB. 19 Db18 The configured level is 18 dB. 20 Db19 The configured level is 19 dB. 21 Db20 The configured level is 20 dB. 22 Db21 The configured level is 21 dB. 23 Db22 The configured level is 22 dB. 24 Db23 The configured level is 23 dB. 25 Db24 The configured level is 24 dB. 26 Db25 The configured level is 25 dB. 27 Db26 The configured level is 26 dB. 28 Db27 The configured level is 27 dB. 29 Db28 The configured level is 28 dB. 30 Db29 The configured level is 29 dB. 31 Db30 The configured level is 30 dB. 32 Db31 The configured level is 31 dB. 130 DbMin1 The configured level is -1 dB (Power Boost). 131 DbMin2 The configured level is -2 dB (Power Boost). 132 DbMin3 The configured level is -3 dB (Power Boost). 133 DbMin4 The configured level is -4 dB (Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwLocalSectionPboAutoEnableLt | 1.3.6.1.4.1.1887.1.1.4.3.2.1.9.1.6 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Reports whether auto power backoff is enabled 1 Off Auto power backoff is disabled 2 On Auto power backoff is enabled 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwLocalSectionPboAutoEnableNt | 1.3.6.1.4.1.1887.1.1.4.3.2.1.9.1.7 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Reports whether auto power backoff is enabled 1 Off Auto power backoff is disabled 2 On Auto power backoff is enabled 254 unknown value 255 unsupported variable for addressed device
| ||||
| TcmrwLocalSetupTable | 1.3.6.1.4.1.1887.1.1.4.3.2.1.10 | NA | mandatory | |
| RcmrwLocalSetupEntry | 1.3.6.1.4.1.1887.1.1.4.3.2.1.10.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CcmrwLocalSetupPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.1.10.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CcmrwLocalSetupLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.1.10.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CcmrwLocalSetupNumWirePairs | 1.3.6.1.4.1.1887.1.1.4.3.2.1.10.1.3 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Indicates the number of wire pairs of the line 1 OneWirePairs Line with one wire pair 2 TwoWirePairs Line with two wire pairs 3 FourWirePairs Line with four wire pairs 254 unknown 255 unsupported Side effect: If you do change this variable all other lines on the card will be affected as well
| ||||
| CcmrwLocalSetupLineActivation | 1.3.6.1.4.1.1887.1.1.4.3.2.1.10.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Indicates whether a line is activated or deactiated. 1 activated The line is activated 2 deactivated The line is deactivated 254 unknown 255 unsupported
| ||||
| CcmrwLocalSetupVirtSysActivation | 1.3.6.1.4.1.1887.1.1.4.3.2.1.10.1.5 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Indicates whether the virtual system is enabled or disabled. 1 disabled The virtual system is disabled 2 enabled The virtual system is enabled 254 unknown 255 unsupported
| ||||
| CcmrwLocalSetupCardActivation | 1.3.6.1.4.1.1887.1.1.4.3.2.1.10.1.6 | OCTET STRING (SIZE (8)) | RW | mandatory |
column · OCTET STRING (SIZE (8)) · read-write · mandatory Indicates the system activation for the systems A to H on the card. Each byte consists of the following information for one system: 1 Deactivated The system is inactive 2 Activated The system is active 254 unknown value 255 unsupported variable for addressed device | ||||
| CcmrwLocalSetupCardActState | 1.3.6.1.4.1.1887.1.1.4.3.2.1.10.1.7 | OCTET STRING (SIZE (8)) | RO | mandatory |
column · OCTET STRING (SIZE (8)) · read-only · mandatory Indicates the system activation state for the systems A to H on the card . Each byte consists of the following information for one system: 1 Current The system belongs to the currently managed line 2 Present The system does not belong to the currently managed line 254 unknown value 255 unsupported variable for addressed device | ||||
| CcmrwLocalSetupIfAssignment | 1.3.6.1.4.1.1887.1.1.4.3.2.1.10.1.8 | OCTET STRING (SIZE (4)) | RW | mandatory |
column · OCTET STRING (SIZE (4)) · read-write · mandatory Indicates the assignment of the (moveable) interfaces 1..4 to the systems A..D on the card . Each byte consists of the following information for one interface: 1 systemA The interface is assigned to System A 2 systemB The interface is assigned to System B 3 systemC The interface is assigned to System C 4 systemD The interface is assigned to System D 254 unknown value 255 unsupported variable for addressed device | ||||
| TcmrwLocalL2SwitchPortTable | 1.3.6.1.4.1.1887.1.1.4.3.2.1.11 | NA | mandatory | |
| RcmrwLocalL2SwitchPortEntry | 1.3.6.1.4.1.1887.1.1.4.3.2.1.11.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CcmrwLocalL2SwitchPortPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.1.11.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CcmrwLocalL2SwitchPortLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.1.11.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CcmrwLocalL2SwitchPortLanPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.1.11.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the L2Switch port (LAN side) and is used as index for the other elements in the Table | ||||
| CcmrwLocalL2SwitchPortEnabled | 1.3.6.1.4.1.1887.1.1.4.3.2.1.11.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Defines whether the L2Switch port is enabled or not. 1 Disabled L2Switch port is disabled 2 Enabled L2Switch port is enabled 254 unknown 255 unsupported
| ||||
| CcmrwLocalL2SwitchPortPhyCfg | 1.3.6.1.4.1.1887.1.1.4.3.2.1.11.1.5 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Defines the ethernet phy config or allows auto negotiation. 1 Full Duplex 10Mbps 2 Full Duplex 100Mbps 3 Half Duplex 10Mbps 4 Half Duplex 100Mbps 5 Auto Negotiation 254 unknown 255 unsupported
| ||||
| CcmrwLocalL2SwitchPortPhyAdvModes | 1.3.6.1.4.1.1887.1.1.4.3.2.1.11.1.6 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory Defines the phy modes to be offered during auto
negotiation ('advertized modes').
Bit 0 1 Full Duplex 10Mbps
Bit 1 2 Full Duplex 100Mbps
Bit 2 4 Half Duplex 10Mbps
Bit 3 8 Half Duplex 100Mbps
Bit 8 256 unknown value (ignore bits 0-7)
Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) | ||||
| CcmrwLocalL2SwitchPortPhyCfgReadout | 1.3.6.1.4.1.1887.1.1.4.3.2.1.11.1.7 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates the current ethernet phy config. 1 Full Duplex 10Mbps 2 Full Duplex 100Mbps 3 Half Duplex 10Mbps 4 Half Duplex 100Mbps 5 Auto Negotiation 6 Linkdown 254 unknown 255 unsupported
| ||||
| CcmrwLocalL2SwitchPortAutoXover | 1.3.6.1.4.1.1887.1.1.4.3.2.1.11.1.8 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Determines whether ethernet crossover (MDI/MDI-X) should automatically be detected and compensated for. 1 Disabled MDI 2 Enabled Auto MDI/MDI-X 254 unknown 255 unsupported
| ||||
| CcmrwLocalL2SwitchPortFlowCtrl | 1.3.6.1.4.1.1887.1.1.4.3.2.1.11.1.9 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Determines whether flow control should be performed on a specific port. 1 Disabled Flow control disabled 2 Enabled Flow control enabled 254 unknown 255 unsupported
| ||||
| CcmrwLocalL2SwitchPortRateLimit | 1.3.6.1.4.1.1887.1.1.4.3.2.1.11.1.10 | INTEGER (0..65535) | RW | mandatory |
column · INTEGER (0..65535) · read-write · mandatory Determines the maximum bit rate on a specific port in 32kbps increments. This setting can be overriden by the Rate Limit Cfg setting. 1 Rate Limit 32kbps 2 Rate Limit 64kbps ... 288 Rate Limit 9216kbps (equals 4*2304 kbps) ... 3125 Rate Limit 100Mbps 65534 unknown 65535 unsupported | ||||
| CcmrwLocalL2SwitchPortRateLimitCfg | 1.3.6.1.4.1.1887.1.1.4.3.2.1.11.1.11 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Determines the behavior of the port rate limiter. on a specific port 1 Unlimited No rate limit enforced 2 User-Def. n*32k User-defined value in 32k increments 254 unknown 255 unsupported
| ||||
| TcmrwLocalMultiIfTable | 1.3.6.1.4.1.1887.1.1.4.3.2.1.12 | NA | mandatory | |
| RcmrwLocalMultiIfEntry | 1.3.6.1.4.1.1887.1.1.4.3.2.1.12.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CcmrwLocalMultiIfPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.1.12.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CcmrwLocalMultiIfLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.1.12.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CcmrwLocalMultiIfInstanceIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.1.12.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses one of several instances and is used as index for the other elements in the Table. Instances can be - U interfaces 1,2,3,4... - V interfaces A,B,C,D... The numbering format is 1,2,3,4... | ||||
| CcmrwLocalMultiIfUEnabled | 1.3.6.1.4.1.1887.1.1.4.3.2.1.12.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Defines whether the U1,U2,U3,U4... interface is enabled or not. 1 Disabled Interface is disabled 2 Enabled Interface is enabled 254 unknown 255 unsupported
| ||||
| CcmrwLocalMultiIfVEnabled | 1.3.6.1.4.1.1887.1.1.4.3.2.1.12.1.5 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Defines whether the V_A,V_B,V_C,V_D... interface is enabled or not. 1 Disabled Interface is disabled 2 Enabled Interface is enabled 254 unknown 255 unsupported
| ||||
| TcmrwLocalCommonMultiChTable | 1.3.6.1.4.1.1887.1.1.4.3.2.1.13 | NA | mandatory | |
| RcmrwLocalCommonMultiChEntry | 1.3.6.1.4.1.1887.1.1.4.3.2.1.13.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CcmrwLocalCommonMultiChPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.1.13.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CcmrwLocalCommonMultiChLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.1.13.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CcmrwLocalCommonMultiChannelIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.1.13.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses one of several instances and is used as index for the other elements in the Table. Instances can be - MCS channels a,b,c,d... - U interfaces 1,2,3,4... - V interfaces A,B,C,D... The numbering format is 1,2,3,4... | ||||
| CcmrwLocalCommonMultiChMcsEnabled | 1.3.6.1.4.1.1887.1.1.4.3.2.1.13.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Defines whether the MCS channel a,b,c,d... is enabled or not. 1 Disabled Channel is disabled 2 Enabled CHannel is enabled 254 unknown 255 unsupported
| ||||
| TcmrwLocalL2SwitchTable | 1.3.6.1.4.1.1887.1.1.4.3.2.1.14 | NA | mandatory | |
| RcmrwLocalL2SwitchEntry | 1.3.6.1.4.1.1887.1.1.4.3.2.1.14.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CcmrwLocalL2SwitchPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.1.14.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CcmrwLocalL2SwitchLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.1.14.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CcmrwLocalL2SwitchHugeFrames | 1.3.6.1.4.1.1887.1.1.4.3.2.1.14.1.3 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Indicates whether the Layer 2 Switch supports so-called Huge Frames (frames longer than 1522 bytes). 1 Disabled Huge frames will be discarded 2 Enabled Huge frames allowed 254 unknown 255 unsupported
| ||||
| CcmrwLocalL2SwitchAdaptiveFlowCtrl | 1.3.6.1.4.1.1887.1.1.4.3.2.1.14.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Indicates whether adaptive flow control on the Layer 2 Switch and on the HDLC bridge is enabled (to avoid packet loss) or not. 1 Disabled Disable adaptive flow control 2 Enabled Enable adaptive flow control 254 unknown 255 unsupported
| ||||
| CcmrwLocalL2SwitchFrameLengthCheck | 1.3.6.1.4.1.1887.1.1.4.3.2.1.14.1.5 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Indicates whether frame length check on the Layer 2 Switch is enabled or not. 1 Disabled Disable frame length check 2 Enabled Enable frame length check 254 unknown 255 unsupported
| ||||
| TcmrwLocalMappingTable | 1.3.6.1.4.1.1887.1.1.4.3.2.1.15 | NA | mandatory | |
| RcmrwLocalMappingEntry | 1.3.6.1.4.1.1887.1.1.4.3.2.1.15.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CcmrwLocalMappingPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.1.15.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CcmrwLocalMappingLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.1.15.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CcmrwLocalMappingEnabled | 1.3.6.1.4.1.1887.1.1.4.3.2.1.15.1.3 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Defines whether Mapping is enabled or disabled. 1 Disabled Mapping is disabled 2 Enabled Mapping is enabled 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwLocalMappingMixedOperation | 1.3.6.1.4.1.1887.1.1.4.3.2.1.15.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Defines whether Mixed Operation (Data to Structured TDM) is enabled or disabled. 1 Disabled Mixed Operation is disabled 2 Enabled Mixed Operation is enabled 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwLocalMappingOmitSTS | 1.3.6.1.4.1.1887.1.1.4.3.2.1.15.1.5 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Defines whether the Signalization Timeslot is actually being transmitted or just mapped, not transmitted. 1 Transmit STS is transmitted 2 Omit STS is mapped, but not transmitted 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwLocalMappingSTSPosition | 1.3.6.1.4.1.1887.1.1.4.3.2.1.15.1.6 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Defines the position of the Signalization Timeslot. 1 unchanged STS mapping is disabled 2 tsPos1 STS position: Timeslot 1 3 tsPos2 STS position: Timeslot 2 4 tsPos3 STS position: Timeslot 3 5 tsPos4 STS position: Timeslot 4 6 tsPos5 STS position: Timeslot 5 7 tsPos6 STS position: Timeslot 6 8 tsPos7 STS position: Timeslot 7 9 tsPos8 STS position: Timeslot 8 10 tsPos9 STS position: Timeslot 9 11 tsPos10 STS position: Timeslot 10 12 tsPos11 STS position: Timeslot 11 13 tsPos12 STS position: Timeslot 12 14 tsPos13 STS position: Timeslot 13 15 tsPos14 STS position: Timeslot 14 16 tsPos15 STS position: Timeslot 15 17 tsPos16 STS position: Timeslot 16 18 tsPos17 STS position: Timeslot 17 19 tsPos18 STS position: Timeslot 18 20 tsPos19 STS position: Timeslot 19 21 tsPos20 STS position: Timeslot 20 22 tsPos21 STS position: Timeslot 21 23 tsPos22 STS position: Timeslot 22 24 tsPos23 STS position: Timeslot 23 25 tsPos24 STS position: Timeslot 24 26 tsPos25 STS position: Timeslot 25 27 tsPos26 STS position: Timeslot 26 28 tsPos27 STS position: Timeslot 27 29 tsPos28 STS position: Timeslot 28 30 tsPos29 STS position: Timeslot 29 31 tsPos30 STS position: Timeslot 30 32 tsPos31 STS position: Timeslot 31 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwLocalMappingTxTs0 | 1.3.6.1.4.1.1887.1.1.4.3.2.1.15.1.7 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Defines whether timeslot 0 is transmitted on the U interface. 1 Disabled TS0 is not transmitted 2 Enabled TS0 is transmitted 254 unknown value 255 unsupported variable for addressed device
| ||||
| NcmrwFar | 1.3.6.1.4.1.1887.1.1.4.3.2.2 | |||
| TcmrwFarClockTable | 1.3.6.1.4.1.1887.1.1.4.3.2.2.3 | NA | mandatory | |
| RcmrwFarClockEntry | 1.3.6.1.4.1.1887.1.1.4.3.2.2.3.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CcmrwFarClockPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.2.3.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CcmrwFarClockLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.2.3.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CcmrwFarClockActive | 1.3.6.1.4.1.1887.1.1.4.3.2.2.3.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates which clock source is currently being used. 1 T3In Uses Clock input T3In 2 TInterface Taking Clock from signal on T-Interface 3 UInterface Taking Clock from signal on U-Interface 4 Internal Using internal oscillator to generate Clock 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwFarClockT3InAvailable | 1.3.6.1.4.1.1887.1.1.4.3.2.2.3.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Reports whether Clock Input T3In is available 1 False Clock Input T3In not available 2 True Clock Input T3In available 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwFarClockTInterfaceAvailable | 1.3.6.1.4.1.1887.1.1.4.3.2.2.3.1.5 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Reports whether a clock signal can be derrived from the signal on the T-Interface 1 False Clock signal available 2 True Clock signal available 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwFarClockUInterfaceAvailable | 1.3.6.1.4.1.1887.1.1.4.3.2.2.3.1.6 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Reports whether a clock signal can be derrived from the signal on the U-Interface 1 False Clock signal available 2 True Clock signal available 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwFarClockInternalAvailable | 1.3.6.1.4.1.1887.1.1.4.3.2.2.3.1.7 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Reports whether the internal oscillator is available 1 False oscillator not available 2 True oscillator available 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwFarClockPriority | 1.3.6.1.4.1.1887.1.1.4.3.2.2.3.1.8 | OCTET STRING (SIZE (4)) | RW | mandatory |
column · OCTET STRING (SIZE (4)) · read-write · mandatory Used to read and set the clock priority for the different clock sources. The variable is an array with length 4. The indices correspond to the priorities (0=highest, 3=lowest). The following values can be contained in each position, indicating which clock source has the corresponding priority: 1 T3In Clock Input T3In 2 TInterface Clock derrived from Signal at T-Interface 3 UInterface Clock derrived from Signal at U-Interface 4 Internal Internal oscillator 254 unknown value 255 unsupported variable for addressed device | ||||
| TcmrwFar2MTable | 1.3.6.1.4.1.1887.1.1.4.3.2.2.4 | NA | mandatory | |
| RcmrwFar2MEntry | 1.3.6.1.4.1.1887.1.1.4.3.2.2.4.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CcmrwFar2MPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.2.4.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CcmrwFar2MLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.2.4.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CcmrwFar2MFraming | 1.3.6.1.4.1.1887.1.1.4.3.2.2.4.1.3 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Configures Frame Alignment 1 Transparent No frame or multi-frame synchronisation 2 Monitoring Frame and Multi-Frame synchronisation but no reinsertion of Frame 3 Termination Frame and Multi-Frame synchronisation and reinsertion 4 Channelized Frame and Multi-Frame synchronisation without transmission of timeslot 0 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwFar2MEnableT | 1.3.6.1.4.1.1887.1.1.4.3.2.2.4.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Enable or disable the G.703 interface (T-Interface) 1 Disabled G.703 Interface is disabled 2 Enabled G.703 Interface is enabled 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwFar2MTimeslotsT | 1.3.6.1.4.1.1887.1.1.4.3.2.2.4.1.5 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Bandwidth allocated for G.703 Interface (T-Interface) as a number of 64kbit/s time slots. Between 1 and 32. When reading the following values can also be returned: 1 bw64 Bandwidth 64 kbit/s 2 bw128 Bandwidth 128 kbit/s 3 bw192 Bandwidth 192 kbit/s 4 bw256 Bandwidth 256 kbit/s 5 bw320 Bandwidth 320 kbit/s 6 bw384 Bandwidth 384 kbit/s 7 bw448 Bandwidth 448 kbit/s 8 bw512 Bandwidth 512 kbit/s 9 bw576 Bandwidth 576 kbit/s 10 bw640 Bandwidth 640 kbit/s 11 bw704 Bandwidth 704 kbit/s 12 bw768 Bandwidth 768 kbit/s 13 bw832 Bandwidth 832 kbit/s 14 bw896 Bandwidth 896 kbit/s 15 bw960 Bandwidth 960 kbit/s 16 bw1024 Bandwidth 1024 kbit/s 17 bw1088 Bandwidth 1088 kbit/s 18 bw1152 Bandwidth 1152 kbit/s 19 bw1216 Bandwidth 1216 kbit/s 20 bw1280 Bandwidth 1280 kbit/s 21 bw1344 Bandwidth 1344 kbit/s 22 bw1408 Bandwidth 1408 kbit/s 23 bw1472 Bandwidth 1472 kbit/s 24 bw1536 Bandwidth 1536 kbit/s 25 bw1600 Bandwidth 1600 kbit/s 26 bw1664 Bandwidth 1664 kbit/s 27 bw1728 Bandwidth 1728 kbit/s 28 bw1792 Bandwidth 1792 kbit/s 29 bw1856 Bandwidth 1856 kbit/s 30 bw1920 Bandwidth 1920 kbit/s 31 bw1984 Bandwidth 1984 kbit/s 32 bw2048 Bandwidth 2048 kbit/s 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwFar2MIdlecodeT | 1.3.6.1.4.1.1887.1.1.4.3.2.2.4.1.6 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Defines the Idle Code on the T-Interface. 1 AIS AIS 2 ES ES 3 PAIS PAIS 4 None No Idle Code 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwFar2MCrc4T | 1.3.6.1.4.1.1887.1.1.4.3.2.2.4.1.7 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Defines whether CRC-4 evaluation at the T-Interface is done. 1 Off CRC-4 Data is not evaluated 2 On CRC-4 Data is evaluated, error if none present in signal 3 AutoOff CRC-4 Data is evaluated, if none is present, evaluation is disabled 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwFar2MCrc4U | 1.3.6.1.4.1.1887.1.1.4.3.2.2.4.1.8 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Defines whether CRC-4 evaluation at the U-Interface is done. 1 Off CRC-4 Data is not evaluated 2 On CRC-4 Data is evaluated, error if none present in signal 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwFar2MDetectAis | 1.3.6.1.4.1.1887.1.1.4.3.2.2.4.1.9 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Defines whether AIS detection is enabled or not 1 NoDetect AIS is not detected 2 Detect AIS is detected 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwFar2MInsertAis | 1.3.6.1.4.1.1887.1.1.4.3.2.2.4.1.10 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Defines whether an AIS signal is regenerated or just passed through 1 NoInsertion Pass signal through 2 Insertion Regenerate signal 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwFar2MSaBits | 1.3.6.1.4.1.1887.1.1.4.3.2.2.4.1.11 | OCTET STRING (SIZE (6)) | RW | mandatory |
column · OCTET STRING (SIZE (6)) · read-write · mandatory Contains the Sa-bit configuration. The variable is an array with length 6. The indicies address the Sa bits as follows: [0] Sa4 [1] Sa5 [2] Sa6 [3] Sa7 [4] Sa8 [5] Sa6 Loop Detection Positions 0,3 and 4 (Sa4, Sa7, Sa8) can contain the following values: 1 Transparent 2 Constant Ones Position 1 (Sa5) can contain the following values: 1 Transparent 2 Constant Ones 3 Insert Position 2 (Sa6) can contain the following values: 1 Transparent 2 Constant Ones 3 ETSI Norm 4 ANSI Norm Position 5 (Sa6 Loop Detection) can contain the following values: 1 Loop Detection Off 2 Loop Detection On All 6 positions can contain the values below: 254 unknown value 255 unsupported variable for addressed device | ||||
| CcmrwFar2MTs16Signalling | 1.3.6.1.4.1.1887.1.1.4.3.2.2.4.1.12 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Defines whether time slot 16 is passed through transparently or whether it is reinsertet. 1 Transparent Passing through TS16 2 New Reinserting TS16 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwFar2MIdlecodeU | 1.3.6.1.4.1.1887.1.1.4.3.2.2.4.1.13 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Defines the Idle Code on the U-Interface. 1 AIS AIS 2 ES ES 3 PAIS PAIS 4 none no Idle Code 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwFar2MTs0Present | 1.3.6.1.4.1.1887.1.1.4.3.2.2.4.1.14 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Defines whether timeslot 0 (G.704 frame) is actually transmitted by the U interface. 1 No Timeslot 0 is re-inserted by receiver 2 Yes Timeslot 0 is actually sent 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwFar2MCrc4V | 1.3.6.1.4.1.1887.1.1.4.3.2.2.4.1.15 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Defines whether CRC-4 evaluation at the V-Interfaces is done. 1 Off CRC-4 Data is not evaluated 2 On CRC-4 Data is evaluated, error if none present in signal 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwFar2MInterfaceImpedance | 1.3.6.1.4.1.1887.1.1.4.3.2.2.4.1.16 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Indicates the impedance of the G.703 interface. 75 ohm75 The impedance of the G.703 interface is 75 Ohm. 120 ohm120 The impedance of the G.703 interface is 120 Ohm. 254 unknown value 255 unsupported variable for addressed device
| ||||
| TcmrwFarDataTable | 1.3.6.1.4.1.1887.1.1.4.3.2.2.5 | NA | mandatory | |
| RcmrwFarDataEntry | 1.3.6.1.4.1.1887.1.1.4.3.2.2.5.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CcmrwFarDataPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.2.5.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CcmrwFarDataLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.2.5.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CcmrwFarDataEnabledD | 1.3.6.1.4.1.1887.1.1.4.3.2.2.5.1.3 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Defines whether the Data Interface is enabled or not. 1 Disabled Data Interface is disabled 2 Enabled Data Interface is enabled 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwFarDataTimeslotsD | 1.3.6.1.4.1.1887.1.1.4.3.2.2.5.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Bandwidth allocated for G.703 Interface (T-Interface) as a number of 64kbit/s time slots. When reading the following values can also be returned: 1 bw64 Bandwidth 64 kbit/s 2 bw128 Bandwidth 128 kbit/s 3 bw192 Bandwidth 192 kbit/s 4 bw256 Bandwidth 256 kbit/s 5 bw320 Bandwidth 320 kbit/s 6 bw384 Bandwidth 384 kbit/s 7 bw448 Bandwidth 448 kbit/s 8 bw512 Bandwidth 512 kbit/s 9 bw576 Bandwidth 576 kbit/s 10 bw640 Bandwidth 640 kbit/s 11 bw704 Bandwidth 704 kbit/s 12 bw768 Bandwidth 768 kbit/s 13 bw832 Bandwidth 832 kbit/s 14 bw896 Bandwidth 896 kbit/s 15 bw960 Bandwidth 960 kbit/s 16 bw1024 Bandwidth 1024 kbit/s 17 bw1088 Bandwidth 1088 kbit/s 18 bw1152 Bandwidth 1152 kbit/s 19 bw1216 Bandwidth 1216 kbit/s 20 bw1280 Bandwidth 1280 kbit/s 21 bw1344 Bandwidth 1344 kbit/s 22 bw1408 Bandwidth 1408 kbit/s 23 bw1472 Bandwidth 1472 kbit/s 24 bw1536 Bandwidth 1536 kbit/s 25 bw1600 Bandwidth 1600 kbit/s 26 bw1664 Bandwidth 1664 kbit/s 27 bw1728 Bandwidth 1728 kbit/s 28 bw1792 Bandwidth 1792 kbit/s 29 bw1856 Bandwidth 1856 kbit/s 30 bw1920 Bandwidth 1920 kbit/s 31 bw1984 Bandwidth 1984 kbit/s 32 bw2048 Bandwidth 2048 kbit/s 33 bw2112 Bandwidth 2112 kbit/s 34 bw2176 Bandwidth 2176 kbit/s 35 bw2240 Bandwidth 2240 kbit/s 36 bw2304 Bandwidth 2304 kbit/s 37 bw2368 Bandwidth 2368 kbit/s 38 bw2432 Bandwidth 2432 kbit/s 39 bw2496 Bandwidth 2496 kbit/s 40 bw2560 Bandwidth 2560 kbit/s 41 bw2624 Bandwidth 2624 kbit/s 42 bw2688 Bandwidth 2688 kbit/s 43 bw2752 Bandwidth 2752 kbit/s 44 bw2816 Bandwidth 2816 kbit/s 45 bw2880 Bandwidth 2880 kbit/s 46 bw2944 Bandwidth 2944 kbit/s 47 bw3008 Bandwidth 3008 kbit/s 48 bw3072 Bandwidth 3072 kbit/s 49 bw3136 Bandwidth 3136 kbit/s 50 bw3200 Bandwidth 3200 kbit/s 51 bw3264 Bandwidth 3264 kbit/s 52 bw3328 Bandwidth 3328 kbit/s 53 bw3392 Bandwidth 3392 kbit/s 54 bw3456 Bandwidth 3456 kbit/s 55 bw3520 Bandwidth 3520 kbit/s 56 bw3584 Bandwidth 3584 kbit/s 57 bw3648 Bandwidth 3648 kbit/s 58 bw3712 Bandwidth 3712 kbit/s 59 bw3776 Bandwidth 3776 kbit/s 60 bw3840 Bandwidth 3840 kbit/s 61 bw3904 Bandwidth 3904 kbit/s 62 bw3968 Bandwidth 3968 kbit/s 63 bw4032 Bandwidth 4032 kbit/s 64 bw4096 Bandwidth 4096 kbit/s 65 bw4160 Bandwidth 4160 kbit/s 66 bw4224 Bandwidth 4224 kbit/s 67 bw4288 Bandwidth 4288 kbit/s 68 bw4352 Bandwidth 4352 kbit/s 69 bw4416 Bandwidth 4416 kbit/s 70 bw4480 Bandwidth 4480 kbit/s 71 bw4544 Bandwidth 4544 kbit/s 72 bw4608 Bandwidth 4608 kbit/s 73 bw4672 Bandwidth 4672 kbit/s 74 bw4736 Bandwidth 4736 kbit/s 75 bw4800 Bandwidth 4800 kbit/s 76 bw4864 Bandwidth 4864 kbit/s 77 bw4928 Bandwidth 4928 kbit/s 78 bw4992 Bandwidth 4992 kbit/s 79 bw5056 Bandwidth 5056 kbit/s 80 bw5120 Bandwidth 5120 kbit/s 81 bw5184 Bandwidth 5184 kbit/s 82 bw5248 Bandwidth 5248 kbit/s 83 bw5312 Bandwidth 5312 kbit/s 84 bw5376 Bandwidth 5376 kbit/s 85 bw5440 Bandwidth 5440 kbit/s 86 bw5504 Bandwidth 5504 kbit/s 87 bw5568 Bandwidth 5568 kbit/s 88 bw5632 Bandwidth 5632 kbit/s 89 bw5696 Bandwidth 5696 kbit/s 90 bw5760 Bandwidth 5760 kbit/s 91 bw5824 Bandwidth 5824 kbit/s 92 bw5888 Bandwidth 5888 kbit/s 93 bw5952 Bandwidth 5952 kbit/s 94 bw6016 Bandwidth 6016 kbit/s 95 bw6080 Bandwidth 6080 kbit/s 96 bw6144 Bandwidth 6144 kbit/s 97 bw6208 Bandwidth 6208 kbit/s 98 bw6272 Bandwidth 6272 kbit/s 99 bw6336 Bandwidth 6336 kbit/s 100 bw6400 Bandwidth 6400 kbit/s 101 bw6464 Bandwidth 6464 kbit/s 102 bw6528 Bandwidth 6528 kbit/s 103 bw6592 Bandwidth 6592 kbit/s 104 bw6656 Bandwidth 6656 kbit/s 105 bw6720 Bandwidth 6720 kbit/s 106 bw6784 Bandwidth 6784 kbit/s 107 bw6848 Bandwidth 6848 kbit/s 108 bw6912 Bandwidth 6912 kbit/s 109 bw6976 Bandwidth 6976 kbit/s 110 bw7040 Bandwidth 7040 kbit/s 111 bw7104 Bandwidth 7104 kbit/s 112 bw7168 Bandwidth 7168 kbit/s 113 bw7232 Bandwidth 7232 kbit/s 114 bw7296 Bandwidth 7296 kbit/s 115 bw7360 Bandwidth 7360 kbit/s 116 bw7424 Bandwidth 7424 kbit/s 117 bw7488 Bandwidth 7488 kbit/s 118 bw7552 Bandwidth 7552 kbit/s 119 bw7616 Bandwidth 7616 kbit/s 120 bw7680 Bandwidth 7680 kbit/s 121 bw7744 Bandwidth 7744 kbit/s 122 bw7808 Bandwidth 7808 kbit/s 123 bw7872 Bandwidth 7872 kbit/s 124 bw7936 Bandwidth 7936 kbit/s 125 bw8000 Bandwidth 8000 kbit/s 126 bw8064 Bandwidth 8064 kbit/s 127 bw8128 Bandwidth 8128 kbit/s 128 bw8192 Bandwidth 8192 kbit/s 129 bw8256 Bandwidth 8256 kbit/s 130 bw8320 Bandwidth 8320 kbit/s 131 bw8384 Bandwidth 8384 kbit/s 132 bw8448 Bandwidth 8448 kbit/s 133 bw8512 Bandwidth 8512 kbit/s 134 bw8576 Bandwidth 8576 kbit/s 135 bw8640 Bandwidth 8640 kbit/s 136 bw8704 Bandwidth 8704 kbit/s 137 bw8768 Bandwidth 8768 kbit/s 138 bw8832 Bandwidth 8832 kbit/s 139 bw8896 Bandwidth 8896 kbit/s 140 bw8960 Bandwidth 8960 kbit/s 141 bw9024 Bandwidth 9024 kbit/s 142 bw9088 Bandwidth 9088 kbit/s 143 bw9152 Bandwidth 9152 kbit/s 144 bw9216 Bandwidth 9216 kbit/s 145 bw9280 Bandwidth 9280 kbit/s 146 bw9344 Bandwidth 9344 kbit/s 147 bw9408 Bandwidth 9408 kbit/s 148 bw9472 Bandwidth 9472 kbit/s 149 bw9536 Bandwidth 9536 kbit/s 150 bw9600 Bandwidth 9600 kbit/s 151 bw9664 Bandwidth 9664 kbit/s 152 bw9728 Bandwidth 9728 kbit/s 153 bw9792 Bandwidth 9792 kbit/s 154 bw9856 Bandwidth 9856 kbit/s 155 bw9920 Bandwidth 9920 kbit/s 156 bw9984 Bandwidth 9984 kbit/s 157 bw10048 Bandwidth 10048 kbit/s 158 bw10112 Bandwidth 10112 kbit/s 159 bw10176 Bandwidth 10176 kbit/s 160 bw10240 Bandwidth 10240 kbit/s 161 bw10304 Bandwidth 10304 kbit/s 162 bw10368 Bandwidth 10368 kbit/s 163 bw10432 Bandwidth 10432 kbit/s 164 bw10496 Bandwidth 10496 kbit/s 165 bw10560 Bandwidth 10560 kbit/s 166 bw10624 Bandwidth 10624 kbit/s 167 bw10688 Bandwidth 10688 kbit/s 168 bw10752 Bandwidth 10752 kbit/s 169 bw10816 Bandwidth 10816 kbit/s 170 bw10880 Bandwidth 10880 kbit/s 171 bw10944 Bandwidth 10944 kbit/s 172 bw11008 Bandwidth 11008 kbit/s 173 bw11072 Bandwidth 11072 kbit/s 174 bw11136 Bandwidth 11136 kbit/s 175 bw11200 Bandwidth 11200 kbit/s 176 bw11264 Bandwidth 11264 kbit/s 177 bw11328 Bandwidth 11328 kbit/s 178 bw11392 Bandwidth 11392 kbit/s 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwFarDataIdlecodeD | 1.3.6.1.4.1.1887.1.1.4.3.2.2.5.1.5 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Defines the Idle Code for the Data Interface. 1 Null Always send 0 2 Ais Always send 1 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwFarDataFastSig | 1.3.6.1.4.1.1887.1.1.4.3.2.2.5.1.6 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Defines whether Fast Signalling is used or not 1 Off Fast Signalling is not used 2 On Fast Signalling is used 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwFarDataLine106 | 1.3.6.1.4.1.1887.1.1.4.3.2.2.5.1.7 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Defines whether control line 106 is set automatically or permanently turned on. 1 Auto Automatically set 2 Perm Permanently on 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwFarDataLine107 | 1.3.6.1.4.1.1887.1.1.4.3.2.2.5.1.8 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Defines whether control line 107 is set automatically or permanently turned on. 1 Auto Automatically set 2 Perm Permanently on 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwFarDataLine109 | 1.3.6.1.4.1.1887.1.1.4.3.2.2.5.1.9 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Defines whether control line 109 is set automatically or permanently turned on. 1 Auto Automatically set 2 Perm Permanently on 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwFarDataLine140 | 1.3.6.1.4.1.1887.1.1.4.3.2.2.5.1.10 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Defines whether control line 140 is set automatically or permanently turned off. 1 Auto Automatically set 2 Perm Permanently off 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwFarDataLine141 | 1.3.6.1.4.1.1887.1.1.4.3.2.2.5.1.11 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Defines whether control line 141 is set automatically or permanently turned off. 1 Auto Automatically set 2 Perm Permanently off 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwFarDataUseTs16ForData | 1.3.6.1.4.1.1887.1.1.4.3.2.2.5.1.12 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Defines whether timeslot 16 can be used for data when no signalling information is transmitted in it. 1 No Timeslot 16 is reserved even if no signalling is used 2 Yes Timeslot 16 is used for data if no signalling is used 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwFarDataEndToEndSignalling | 1.3.6.1.4.1.1887.1.1.4.3.2.2.5.1.13 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Defines whether End To End Signalling is enabled. 1 Disabled End To End Signalling is disabled 2 FastSig End To End Signalling is fast signalling 3 CAS End To End Signalling is CAS 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwFarDataDteDceMode | 1.3.6.1.4.1.1887.1.1.4.3.2.2.5.1.14 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Defines the operation mode of the data interface. 1 DCE Data Interface operates in DCE (Data Circuit-Terminating Equipment) mode 2 DTE Data Interface operates in DTE (Data Terminal Equipment) mode 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwFarDataIfSelector | 1.3.6.1.4.1.1887.1.1.4.3.2.2.5.1.15 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Selects the active data Interface. 1 mgblEthIf Manageable Ethernet Interface is selected 2 multiPurpDataIf Multi Purpose Data Interface is selected 254 unknown value 255 unsupported variable for addressed device
| ||||
| TcmrwFarActionTable | 1.3.6.1.4.1.1887.1.1.4.3.2.2.6 | NA | mandatory | |
| RcmrwFarActionEntry | 1.3.6.1.4.1.1887.1.1.4.3.2.2.6.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CcmrwFarActionPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.2.6.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CcmrwFarActionLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.2.6.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CcmrwFarActionReboot | 1.3.6.1.4.1.1887.1.1.4.3.2.2.6.1.3 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Command to reboot device. The parameter specifies whether the firmware in the active or passive bank shall be started. 1 Passive Reboot using the passive firmware 2 Active Reboot using the active firmware 254 unknown value 255 unsupported variable for addressed device If the parameter 'passive' is specified but the passive firmware bank contains no valid code, the device reboots using the active firmware.
| ||||
| TcmrwFarUserDataTable | 1.3.6.1.4.1.1887.1.1.4.3.2.2.7 | NA | mandatory | |
| RcmrwFarUserDataEntry | 1.3.6.1.4.1.1887.1.1.4.3.2.2.7.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CcmrwFarUserDataPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.2.7.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CcmrwFarUserDataLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.2.7.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CcmrwFarUserDataItemIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.2.7.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the data field number of the user data and is used as index for the other elements in the Table | ||||
| CcmrwFarUserData | 1.3.6.1.4.1.1887.1.1.4.3.2.2.7.1.4 | DisplayString (SIZE (100)) | RW | mandatory |
column · DisplayString (SIZE (100)) · read-write · mandatory User data that can be written to the device | ||||
| TcmrwFarRpsTable | 1.3.6.1.4.1.1887.1.1.4.3.2.2.8 | NA | mandatory | |
| RcmrwFarRpsEntry | 1.3.6.1.4.1.1887.1.1.4.3.2.2.8.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CcmrwFarRpsPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.2.8.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CcmrwFarRpsLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.2.8.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CcmrwFarRps | 1.3.6.1.4.1.1887.1.1.4.3.2.2.8.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether the Remote Power Supply is on/off. 1 Inactive The RPS is turned off 2 Active The RPS is turned on 254 unknown value 255 unsupported
| ||||
| CcmrwFarRpsCurrent | 1.3.6.1.4.1.1887.1.1.4.3.2.2.8.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates the Remote Power Supply current. 50 Inactive RPS current limied to 50 mA 60 Active RPS current limited to 60 mA 254 unknown value 255 unsupported
| ||||
| TcmrwFarL2SwitchPortTable | 1.3.6.1.4.1.1887.1.1.4.3.2.2.9 | NA | mandatory | |
| RcmrwFarL2SwitchPortEntry | 1.3.6.1.4.1.1887.1.1.4.3.2.2.9.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CcmrwFarL2SwitchPortPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.2.9.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CcmrwFarL2SwitchPortLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.2.9.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CcmrwFarL2SwitchPortLanPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.2.9.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the L2Switch port (LAN side) and is used as index for the other elements in the Table | ||||
| CcmrwFarL2SwitchPortEnabled | 1.3.6.1.4.1.1887.1.1.4.3.2.2.9.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Defines whether the L2Switch port is enabled or not. 1 Disabled L2Switch port is disabled 2 Enabled L2Switch port is enabled 254 unknown 255 unsupported
| ||||
| CcmrwFarL2SwitchPortPhyCfg | 1.3.6.1.4.1.1887.1.1.4.3.2.2.9.1.5 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Defines the ethernet phy config or allows auto negotiation. 1 Full Duplex 10Mbps 2 Full Duplex 100Mbps 3 Half Duplex 10Mbps 4 Half Duplex 100Mbps 5 Auto Negotiation 254 unknown 255 unsupported
| ||||
| CcmrwFarL2SwitchPortPhyAdvModes | 1.3.6.1.4.1.1887.1.1.4.3.2.2.9.1.6 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory Defines the phy modes to be offered during auto
negotiation ('advertized modes').
Bit 0 1 Full Duplex 10Mbps
Bit 1 2 Full Duplex 100Mbps
Bit 2 4 Half Duplex 10Mbps
Bit 3 8 Half Duplex 100Mbps
Bit 8 256 unknown value (ignore bits 0-7)
Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) | ||||
| CcmrwFarL2SwitchPortPhyCfgReadout | 1.3.6.1.4.1.1887.1.1.4.3.2.2.9.1.7 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates the current ethernet phy config. 1 Full Duplex 10Mbps 2 Full Duplex 100Mbps 3 Half Duplex 10Mbps 4 Half Duplex 100Mbps 5 Auto Negotiation 6 Linkdown 254 unknown 255 unsupported
| ||||
| CcmrwFarL2SwitchPortAutoXover | 1.3.6.1.4.1.1887.1.1.4.3.2.2.9.1.8 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Determines whether ethernet crossover (MDI/MDI-X) should automatically be detected and compensated for. 1 Disabled MDI 2 Enabled Auto MDI/MDI-X 254 unknown 255 unsupported
| ||||
| CcmrwFarL2SwitchPortFlowCtrl | 1.3.6.1.4.1.1887.1.1.4.3.2.2.9.1.9 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Determines whether flow control should be performed on a specific port. 1 Disabled Flow control disabled 2 Enabled Flow control enabled 254 unknown 255 unsupported
| ||||
| CcmrwFarL2SwitchPortRateLimit | 1.3.6.1.4.1.1887.1.1.4.3.2.2.9.1.10 | INTEGER (0..65535) | RW | mandatory |
column · INTEGER (0..65535) · read-write · mandatory Determines the maximum bit rate on a specific port in 32kbps increments. This setting can be overriden by the Rate Limit Cfg setting. 32 Rate Limit 32kbps 64 Rate Limit 64kbps ... 9216 Rate Limit 9216kbps (equals 4*2304 kbps) ... xxx Rate Limit xxxxkbps 65534 unknown 65535 unsupported | ||||
| CcmrwFarL2SwitchPortRateLimitCfg | 1.3.6.1.4.1.1887.1.1.4.3.2.2.9.1.11 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Determines the behavior of the port rate limiter. on a specific port 1 Unlimited No rate limit enforced 2 User-Def. n*32k User-defined value in 32k increments 254 unknown 255 unsupported
| ||||
| TcmrwFarMultiIfTable | 1.3.6.1.4.1.1887.1.1.4.3.2.2.10 | NA | mandatory | |
| RcmrwFarMultiIfEntry | 1.3.6.1.4.1.1887.1.1.4.3.2.2.10.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CcmrwFarMultiIfPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.2.10.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CcmrwFarMultiIfLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.2.10.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CcmrwFarMultiIfInstanceIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.2.10.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses one of several instances and is used as index for the other elements in the Table. Instances can be - U interfaces 1,2,3,4... - V interfaces A,B,C,D... The numbering format is 1,2,3,4... | ||||
| CcmrwFarMultiIfUEnabled | 1.3.6.1.4.1.1887.1.1.4.3.2.2.10.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Defines whether the U1,U2,U3,U4... interface is enabled or not. 1 Disabled Interface is disabled 2 Enabled Interface is enabled 254 unknown 255 unsupported
| ||||
| CcmrwFarMultiIfVEnabled | 1.3.6.1.4.1.1887.1.1.4.3.2.2.10.1.5 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Defines whether the V_A,V_B,V_C,V_D... interface is enabled or not. 1 Disabled Interface is disabled 2 Enabled Interface is enabled 254 unknown 255 unsupported
| ||||
| TcmrwFarL2SwitchTable | 1.3.6.1.4.1.1887.1.1.4.3.2.2.11 | NA | mandatory | |
| RcmrwFarL2SwitchEntry | 1.3.6.1.4.1.1887.1.1.4.3.2.2.11.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CcmrwFarL2SwitchPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.2.11.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CcmrwFarL2SwitchLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.2.11.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CcmrwFarL2SwitchHugeFrames | 1.3.6.1.4.1.1887.1.1.4.3.2.2.11.1.3 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Indicates whether the Layer 2 Switch supports so-called Huge Frames (frames longer than 1522 bytes). 1 Disabled Huge frames will be discarded 2 Enabled Huge frames allowed 254 unknown 255 unsupported
| ||||
| CcmrwFarL2SwitchAdaptiveFlowCtrl | 1.3.6.1.4.1.1887.1.1.4.3.2.2.11.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Indicates whether adaptive flow control on the Layer 2 Switch and on the HDLC bridge is enabled (to avoid packet loss) or not. 1 Disabled Disable adaptive flow control 2 Enabled Enable adaptive flow control 254 unknown 255 unsupported
| ||||
| CcmrwFarL2SwitchFrameLengthCheck | 1.3.6.1.4.1.1887.1.1.4.3.2.2.11.1.5 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Indicates whether frame length check on the Layer 2 Switch is enabled or not. 1 Disabled Disable frame length check 2 Enabled Enable frame length check 254 unknown 255 unsupported
| ||||
| TcmrwFarMappingTable | 1.3.6.1.4.1.1887.1.1.4.3.2.2.12 | NA | mandatory | |
| RcmrwFarMappingEntry | 1.3.6.1.4.1.1887.1.1.4.3.2.2.12.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CcmrwFarMappingPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.2.12.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CcmrwFarMappingLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.2.12.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CcmrwFarMappingEnabled | 1.3.6.1.4.1.1887.1.1.4.3.2.2.12.1.3 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Defines whether Mapping is enabled or disabled. 1 Disabled Mapping is disabled 2 Enabled Mapping is enabled 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwFarMappingMixedOperation | 1.3.6.1.4.1.1887.1.1.4.3.2.2.12.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Defines whether Mixed Operation (Data to Structured TDM) is enabled or disabled. 1 Disabled Mixed Operation is disabled 2 Enabled Mixed Operation is enabled 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwFarMappingOmitSTS | 1.3.6.1.4.1.1887.1.1.4.3.2.2.12.1.5 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Defines whether the Signalization Timeslot is actually being transmitted or just mapped, not transmitted. 1 Transmit STS is transmitted 2 Omit STS is mapped, but not transmitted 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwFarMappingSTSPosition | 1.3.6.1.4.1.1887.1.1.4.3.2.2.12.1.6 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Defines the position of the Signalization Timeslot. 1 unchanged STS mapping is disabled 2 tsPos1 STS position: Timeslot 1 3 tsPos2 STS position: Timeslot 2 4 tsPos3 STS position: Timeslot 3 5 tsPos4 STS position: Timeslot 4 6 tsPos5 STS position: Timeslot 5 7 tsPos6 STS position: Timeslot 6 8 tsPos7 STS position: Timeslot 7 9 tsPos8 STS position: Timeslot 8 10 tsPos9 STS position: Timeslot 9 11 tsPos10 STS position: Timeslot 10 12 tsPos11 STS position: Timeslot 11 13 tsPos12 STS position: Timeslot 12 14 tsPos13 STS position: Timeslot 13 15 tsPos14 STS position: Timeslot 14 16 tsPos15 STS position: Timeslot 15 17 tsPos16 STS position: Timeslot 16 18 tsPos17 STS position: Timeslot 17 19 tsPos18 STS position: Timeslot 18 20 tsPos19 STS position: Timeslot 19 21 tsPos20 STS position: Timeslot 20 22 tsPos21 STS position: Timeslot 21 23 tsPos22 STS position: Timeslot 22 24 tsPos23 STS position: Timeslot 23 25 tsPos24 STS position: Timeslot 24 26 tsPos25 STS position: Timeslot 25 27 tsPos26 STS position: Timeslot 26 28 tsPos27 STS position: Timeslot 27 29 tsPos28 STS position: Timeslot 28 30 tsPos29 STS position: Timeslot 29 31 tsPos30 STS position: Timeslot 30 32 tsPos31 STS position: Timeslot 31 254 unknown value 255 unsupported variable for addressed device
| ||||
| CcmrwFarMappingTxTs0 | 1.3.6.1.4.1.1887.1.1.4.3.2.2.12.1.7 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Defines whether timeslot 0 is transmitted on the U interface. 1 Disabled TS0 is not transmitted 2 Enabled TS0 is transmitted 254 unknown value 255 unsupported variable for addressed device
| ||||
| TcmrwFarSetupTable | 1.3.6.1.4.1.1887.1.1.4.3.2.2.13 | NA | mandatory | |
| RcmrwFarSetupEntry | 1.3.6.1.4.1.1887.1.1.4.3.2.2.13.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CcmrwFarSetupPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.2.13.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CcmrwFarSetupLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.2.13.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CcmrwFarSetupCardActivation | 1.3.6.1.4.1.1887.1.1.4.3.2.2.13.1.3 | OCTET STRING (SIZE (8)) | RW | mandatory |
column · OCTET STRING (SIZE (8)) · read-write · mandatory Indicates the system activation for the systems A to H on the card. Each byte consists of the following information for one system: 1 Deactivated The system is inactive 2 Activated The system is active 254 unknown value 255 unsupported variable for addressed device | ||||
| CcmrwFarSetupCardActState | 1.3.6.1.4.1.1887.1.1.4.3.2.2.13.1.4 | OCTET STRING (SIZE (8)) | RO | mandatory |
column · OCTET STRING (SIZE (8)) · read-only · mandatory Indicates the system activation state for the systems A to H on the card . Each byte consists of the following information for one system: 1 Current The system belongs to the currently managed line 2 Present The system does not belong to the currently managed line 254 unknown value 255 unsupported variable for addressed device | ||||
| CcmrwFarSetupIfAssignment | 1.3.6.1.4.1.1887.1.1.4.3.2.2.13.1.5 | OCTET STRING (SIZE (4)) | RW | mandatory |
column · OCTET STRING (SIZE (4)) · read-write · mandatory Indicates the assignment of the (moveable) interfaces 1..4 to the systems A..D on the card . Each byte consists of the following information for one interface: 1 systemA The interface is assigned to System A 2 systemB The interface is assigned to System B 3 systemC The interface is assigned to System C 4 systemD The interface is assigned to System D 254 unknown value 255 unsupported variable for addressed device | ||||
| NcmrwOmi | 1.3.6.1.4.1.1887.1.1.4.3.2.3 | |||
| TcmrwOmiTokenTable | 1.3.6.1.4.1.1887.1.1.4.3.2.3.1 | NA | mandatory | |
| RcmrwOmiTokenEntry | 1.3.6.1.4.1.1887.1.1.4.3.2.3.1.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CcmrwOmiTokenPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.3.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CcmrwOmiTokenResId | 1.3.6.1.4.1.1887.1.1.4.3.2.3.1.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates who is in posession of the reservation token for this device. 1 Available The token is free 2 Lineint The token is given to the LineIntegrator 3 Lct The token is given to the Local Craft Terminal (LCT) 254 unknown value 255 unsupported variable for the addressed device
| ||||
| CcmrwOmiTokenTicket | 1.3.6.1.4.1.1887.1.1.4.3.2.3.1.1.7 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Is used to request or refresh the token device. 1-10 Token1-10 The token was granted/refreshed, the index helps to detect whether it has expried since last reading from this variable 11 NotGranted The token was not granted 12 Lost The token could not be refreshed 13 NotRequested The token has not been requested 254 unknown value 255 unsupported variable for the addressed device
| ||||
| CcmrwOmiTokenSessionId | 1.3.6.1.4.1.1887.1.1.4.3.2.3.1.1.8 | INTEGER (0..65535) | RW | mandatory |
column · INTEGER (0..65535) · read-write · mandatory Indicates which SNMP management is in posession of the reservation token for this device. 0 Invalid The session value is invalid 65535 Unsupported unsupported variable for the addressed device | ||||
| TcmrwOmiActionTable | 1.3.6.1.4.1.1887.1.1.4.3.2.3.6 | NA | mandatory | |
| RcmrwOmiActionEntry | 1.3.6.1.4.1.1887.1.1.4.3.2.3.6.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CcmrwOmiActionPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.3.6.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CcmrwOmiActionReboot | 1.3.6.1.4.1.1887.1.1.4.3.2.3.6.1.2 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Command to reboot device. The parameter specifies whether the firmware in the active or passive bank shall be started. 1 Passive Reboot using the passive firmware 2 Active Reboot using the active firmware If the parameter 'passive' is specified but the passive firmware bank contains no valid code, the device reboots using the active firmware.
| ||||
| TcmrwOmiConfigTable | 1.3.6.1.4.1.1887.1.1.4.3.2.3.7 | NA | mandatory | |
| RcmrwOmiConfigEntry | 1.3.6.1.4.1.1887.1.1.4.3.2.3.7.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CcmrwOmiConfigPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.3.7.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CcmrwOmiConfigVirtSlotPolling | 1.3.6.1.4.1.1887.1.1.4.3.2.3.7.1.2 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Is used to enable/disable the polling of the virtual slots (0x80). 1 Disabled The polling of the virtual slots is disabled 2 Enabled The polling of the virtual slots is enabled
| ||||
| CcmrwOmiNTPServer1 | 1.3.6.1.4.1.1887.1.1.4.3.2.3.7.1.3 | OCTET STRING (SIZE (4)) | RW | mandatory |
column · OCTET STRING (SIZE (4)) · read-write · mandatory NTP Server 1 | ||||
| CcmrwOmiNTPServer2 | 1.3.6.1.4.1.1887.1.1.4.3.2.3.7.1.4 | OCTET STRING (SIZE (4)) | RW | mandatory |
column · OCTET STRING (SIZE (4)) · read-write · mandatory NTP Server 2 | ||||
| CcmrwOmiSNTPClientMode | 1.3.6.1.4.1.1887.1.1.4.3.2.3.7.1.5 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory SNTP client mode: 1 UNICAST 2 BROADCAST 3 DISABLED 254 UNKNOWN 255 UNSUPPORTED
| ||||
| CcmrwOmiSNTPLocalUDPPort | 1.3.6.1.4.1.1887.1.1.4.3.2.3.7.1.6 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory SNTP local UDP port 1..65535 | ||||
| CcmrwOmiDateTime | 1.3.6.1.4.1.1887.1.1.4.3.2.3.7.1.7 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Unix system date (seconds elapsed since 1970-01-01) | ||||
| CcmrwOmiNMS1PortConfig | 1.3.6.1.4.1.1887.1.1.4.3.2.3.7.1.8 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory NMS port configuration. 1 AUTO 2 10 Mbps full duplex 3 10 Mbps half duplex 4 100 Mbps full duplex 5 100 Mbps half duplex 254 UNKNOWN 255 UNSUPPORTED
| ||||
| CcmrwOmiNMS1PortStatus | 1.3.6.1.4.1.1887.1.1.4.3.2.3.7.1.9 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory NMS Port status.
1 AUTO
2 10 Mbps full duplex
3 10 Mbps half duplex
4 100 Mbps full duplex
5 100 Mbps half duplex
6 link down
254 UNKNOWN
255 UNSUPPORTED
| ||||
| CcmrwOmiNMS1PortAutoConfig | 1.3.6.1.4.1.1887.1.1.4.3.2.3.7.1.10 | OCTET STRING (SIZE (1)) | RW | mandatory |
column · OCTET STRING (SIZE (1)) · read-write · mandatory NMS port auto conf: Bit fields: Advertised mode Mode is coded as follows: bit 0 if 1 full 10 Mbps bit 1 if 1 full 100 Mbps bit 2 if 1 half 10 Mbps bit 3 if 1 half 100 Mbps 0xFE UNKNOWN 0xFF UNSUPPORTED | ||||
| CcmrwOmiNMS2PortConfig | 1.3.6.1.4.1.1887.1.1.4.3.2.3.7.1.11 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory NMS port configuration. 1 AUTO 2 10 Mbps full duplex 3 10 Mbps half duplex 4 100 Mbps full duplex 5 100 Mbps half duplex 254 UNKNOWN 255 UNSUPPORTED
| ||||
| CcmrwOmiNMS2PortStatus | 1.3.6.1.4.1.1887.1.1.4.3.2.3.7.1.12 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory NMS Port status. 1 AUTO 2 10 Mbps full duplex 3 10 Mbps half duplex 4 100 Mbps full duplex 5 100 Mbps half duplex 6 link down 254 UNKNOWN 255 UNSUPPORTED
| ||||
| CcmrwOmiNMS2PortAutoConfig | 1.3.6.1.4.1.1887.1.1.4.3.2.3.7.1.13 | OCTET STRING (SIZE (1)) | RW | mandatory |
column · OCTET STRING (SIZE (1)) · read-write · mandatory NMS port auto conf: Bit fields: Advertised mode Mode is coded as follows: bit 0 if 1 full 10 Mbps bit 1 if 1 full 100 Mbps bit 2 if 1 half 10 Mbps bit 3 if 1 half 100 Mbps 0xFE UNKNOWN 0xFF UNSUPPORTED | ||||
| CcmrwOmiNMS3PortConfig | 1.3.6.1.4.1.1887.1.1.4.3.2.3.7.1.14 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory NMS port configuration. 1 AUTO 2 10 Mbps full duplex 3 10 Mbps half duplex 4 100 Mbps full duplex 5 100 Mbps half duplex 254 UNKNOWN 255 UNSUPPORTED
| ||||
| CcmrwOmiNMS3PortStatus | 1.3.6.1.4.1.1887.1.1.4.3.2.3.7.1.15 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory NMS Port status. 1 AUTO 2 10 Mbps full duplex 3 10 Mbps half duplex 4 100 Mbps full duplex 5 100 Mbps half duplex 6 link down 254 UNKNOWN 255 UNSUPPORTED
| ||||
| CcmrwOmiNMS3PortAutoConfig | 1.3.6.1.4.1.1887.1.1.4.3.2.3.7.1.16 | OCTET STRING (SIZE (1)) | RW | mandatory |
column · OCTET STRING (SIZE (1)) · read-write · mandatory NMS port auto conf: Bit fields: Advertised mode Mode is coded as follows: bit 0 if 1 full 10 Mbps bit 1 if 1 full 100 Mbps bit 2 if 1 half 10 Mbps bit 3 if 1 half 100 Mbps 0xFE UNKNOWN 0xFF UNSUPPORTED | ||||
| NcmrwSru | 1.3.6.1.4.1.1887.1.1.4.3.2.4 | |||
| TcmrwSruActionTable | 1.3.6.1.4.1.1887.1.1.4.3.2.4.1 | NA | mandatory | |
| RcmrwSruActionEntry | 1.3.6.1.4.1.1887.1.1.4.3.2.4.1.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CcmrwSruActionPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.4.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CcmrwSruActionLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.4.1.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CcmrwSruActionRegIndex | 1.3.6.1.4.1.1887.1.1.4.3.2.4.1.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the regenerator device and is used as index for the other elements in the Table
| ||||
| CcmrwSruActionReboot | 1.3.6.1.4.1.1887.1.1.4.3.2.4.1.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Command to reboot device. The parameter specifies whether the firmware in the active or passive bank shall be started. 1 Passive Reboot using the passive firmware 2 Active Reboot using the active firmware If the parameter 'passive' is specified but the passive firmware bank contains no valid code, the device reboots using the active firmware.
| ||||
| Nfmro | 1.3.6.1.4.1.1887.1.1.4.3.3 | |||
| TfmroOmiTable | 1.3.6.1.4.1.1887.1.1.4.3.3.1 | NA | mandatory | |
| RfmroOmiEntry | 1.3.6.1.4.1.1887.1.1.4.3.3.1.1 | NA | mandatory | |
row · not-accessible · mandatory
| ||||
| CfmroOmiPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.3.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CfmroOmiBattery1 | 1.3.6.1.4.1.1887.1.1.4.3.3.1.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Battery alarm of the OMI card. 1 None No Alarm 2 BatteryAlarm Power failure on Battery 1 254 unknown value 255 unsupported variable for addressed device
| ||||
| CfmroOmiBattery2 | 1.3.6.1.4.1.1887.1.1.4.3.3.1.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Battery alarm of the OMI card. 1 None No Alarm 2 BatteryAlarm Power failure on Battery 2 254 unknown value 255 unsupported variable for addressed device
| ||||
| CfmroOmiSaw | 1.3.6.1.4.1.1887.1.1.4.3.3.1.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Alarm summary of the OMI card. Bit 0 1 Urgent Alarm Bit 1 2 Non-urgent Alarm Bit 2 4 AIS (Alarm Indication Signal) Bit 6 64 unknown Bit 7 128 unsupported | ||||
| CfmroOmiAuxMcuPower | 1.3.6.1.4.1.1887.1.1.4.3.3.1.1.5 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Battery alarm of the OMI card. 1 No Alarm 2 Power failure on Auxiliary MCU battery 254 unknown value 255 unsupported variable for addressed device
| ||||
| CfmroOmiExtInput1 | 1.3.6.1.4.1.1887.1.1.4.3.3.1.1.6 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory External alarm 1 of the MCU card. 1 No Alarm 2 External Alarm 1 254 unknown value 255 unsupported variable for addressed device
| ||||
| CfmroOmiExtInput2 | 1.3.6.1.4.1.1887.1.1.4.3.3.1.1.7 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory External alarm 2 of the MCU card. 1 No Alarm 2 External Alarm 2 254 unknown value 255 unsupported variable for addressed device
| ||||
| CfmroOmiExtInput3 | 1.3.6.1.4.1.1887.1.1.4.3.3.1.1.8 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory External alarm 3 of the MCU card. 1 No Alarm 2 External Alarm 3 254 unknown value 255 unsupported variable for addressed device
| ||||
| CfmroOmiExtInput4 | 1.3.6.1.4.1.1887.1.1.4.3.3.1.1.9 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory External alarm of the MCU card. 1 No Alarm 2 External Alarm 4 254 unknown value 255 unsupported variable for addressed device
| ||||
| CfmroOmiNMSInterface1 | 1.3.6.1.4.1.1887.1.1.4.3.3.1.1.10 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory NMS Interface 1 alarm of the MCU card. 1 No Alarm 24 LinkDown No Link Detected 254 unknown value 255 unsupported variable for addressed device
| ||||
| CfmroOmiNMSInterface2 | 1.3.6.1.4.1.1887.1.1.4.3.3.1.1.11 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory NMS Interface 2 alarm of the MCU card. 1 No Alarm 24 LinkDown No Link Detected 254 unknown value 255 unsupported variable for addressed device
| ||||
| CfmroOmiNMSInterface3 | 1.3.6.1.4.1.1887.1.1.4.3.3.1.1.12 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory NMS Interface 3 alarm of the MCU card. 1 No Alarm 24 LinkDown No Link Detected 254 unknown value 255 unsupported variable for addressed device
| ||||
| CfmroOmiFEInterface1 | 1.3.6.1.4.1.1887.1.1.4.3.3.1.1.13 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Fast Ethernet Interface 1 alarm of the MCU card. 1 No Alarm 24 LinkDown No Link Detected 254 unknown value 255 unsupported variable for addressed device
| ||||
| CfmroOmiFEInterface2 | 1.3.6.1.4.1.1887.1.1.4.3.3.1.1.14 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Fast Ethernet Interface 2 alarm of the MCU card. 1 No Alarm 24 LinkDown No Link Detected 254 unknown value 255 unsupported variable for addressed device
| ||||
| CfmroOmiFEInterface3 | 1.3.6.1.4.1.1887.1.1.4.3.3.1.1.15 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Fast Ethernet Interface 3 alarm of the MCU card. 1 No Alarm 24 LinkDown No Link Detected 254 unknown value 255 unsupported variable for addressed device
| ||||
| CfmroOmiFEInterface4 | 1.3.6.1.4.1.1887.1.1.4.3.3.1.1.16 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Fast Ethernet Interface 4 alarm of the MCU card. 1 No Alarm 24 LinkDown No Link Detected 254 unknown value 255 unsupported variable for addressed device
| ||||
| CfmroOmiFEInterface5 | 1.3.6.1.4.1.1887.1.1.4.3.3.1.1.17 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Fast Ethernet Interface 5 alarm of the MCU card. 1 No Alarm 24 LinkDown No Link Detected 254 unknown value 255 unsupported variable for addressed device
| ||||
| CfmroOmiFEInterface6 | 1.3.6.1.4.1.1887.1.1.4.3.3.1.1.18 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Fast Ethernet Interface 6 alarm of the MCU card. 1 No Alarm 24 LinkDown No Link Detected 254 unknown value 255 unsupported variable for addressed device
| ||||
| CfmroOmiFEInterface7 | 1.3.6.1.4.1.1887.1.1.4.3.3.1.1.19 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Fast Ethernet Interface 7 alarm of the MCU card. 1 No Alarm 24 LinkDown No Link Detected 254 unknown value 255 unsupported variable for addressed device
| ||||
| CfmroOmiFEInterface8 | 1.3.6.1.4.1.1887.1.1.4.3.3.1.1.20 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Fast Ethernet Interface 8 alarm of the MCU card. 1 No Alarm 24 LinkDown No Link Detected 254 unknown value 255 unsupported variable for addressed device
| ||||
| CfmroOmiFEInterface9 | 1.3.6.1.4.1.1887.1.1.4.3.3.1.1.21 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Fast Ethernet Interface 9 alarm of the MCU card. 1 No Alarm 24 LinkDown No Link Detected 254 unknown value 255 unsupported variable for addressed device
| ||||
| CfmroOmiFEInterface10 | 1.3.6.1.4.1.1887.1.1.4.3.3.1.1.22 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Fast Ethernet Interface 10 alarm of the MCU card. 1 No Alarm 24 LinkDown No Link Detected 254 unknown value 255 unsupported variable for addressed device
| ||||
| CfmroOmiFEInterface11 | 1.3.6.1.4.1.1887.1.1.4.3.3.1.1.23 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Fast Ethernet Interface 11 alarm of the MCU card. 1 No Alarm 24 LinkDown No Link Detected 254 unknown value 255 unsupported variable for addressed device
| ||||
| CfmroOmiFEInterface12 | 1.3.6.1.4.1.1887.1.1.4.3.3.1.1.24 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Fast Ethernet Interface 12 alarm of the MCU card. 1 No Alarm 24 LinkDown No Link Detected 254 unknown value 255 unsupported variable for addressed device
| ||||
| CfmroOmiFEInterface13 | 1.3.6.1.4.1.1887.1.1.4.3.3.1.1.25 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Fast Ethernet Interface 13 alarm of the MCU card. 1 No Alarm 24 LinkDown No Link Detected 254 unknown value 255 unsupported variable for addressed device
| ||||
| CfmroOmiFEInterface14 | 1.3.6.1.4.1.1887.1.1.4.3.3.1.1.26 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Fast Ethernet Interface 14 alarm of the MCU card. 1 No Alarm 24 LinkDown No Link Detected 254 unknown value 255 unsupported variable for addressed device
| ||||
| CfmroOmiFEInterface15 | 1.3.6.1.4.1.1887.1.1.4.3.3.1.1.27 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Fast Ethernet Interface 15 alarm of the MCU card. 1 No Alarm 24 LinkDown No Link Detected 254 unknown value 255 unsupported variable for addressed device
| ||||
| CfmroOmiFEInterface16 | 1.3.6.1.4.1.1887.1.1.4.3.3.1.1.28 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Fast Ethernet Interface 16 alarm of the MCU card. 1 No Alarm 24 LinkDown No Link Detected 254 unknown value 255 unsupported variable for addressed device
| ||||
| CfmroOmiGBEUplink1 | 1.3.6.1.4.1.1887.1.1.4.3.3.1.1.29 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory GBE 1 link down alarm of the MCU card. 1 No Alarm 24 LinkDown No Link Detected 254 unknown value 255 unsupported variable for addressed device
| ||||
| CfmroOmiGBEUplink2 | 1.3.6.1.4.1.1887.1.1.4.3.3.1.1.30 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory GBE 2 link down alarm of the MCU card. 1 No Alarm 24 LinkDown No Link Detected 254 unknown value 255 unsupported variable for addressed device
| ||||
| CfmroOmiSFPLaser1 | 1.3.6.1.4.1.1887.1.1.4.3.3.1.1.31 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory SFP 1 laser alarm of the MCU card. 1 No Alarm 10 Alarm Alarm present 254 unknown value 255 unsupported variable for addressed device
| ||||
| CfmroOmiSFPLaser2 | 1.3.6.1.4.1.1887.1.1.4.3.3.1.1.32 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory SFP 2 laser alarm of the MCU card. 1 No Alarm 10 Alarm Alarm present 254 unknown value 255 unsupported variable for addressed device
| ||||
| CfmroOmiSFPInterface1 | 1.3.6.1.4.1.1887.1.1.4.3.3.1.1.33 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory SFP 1 interface alarm of the MCU card 1 No Alarm 9 LOS Loss of Signal 254 unknown value 255 unsupported variable for addressed device
| ||||
| CfmroOmiSFPInterface2 | 1.3.6.1.4.1.1887.1.1.4.3.3.1.1.34 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory SFP 2 interface alarm of the MCU card. 1 No Alarm 9 LOS Loss of Signal 254 unknown value 255 unsupported variable for addressed device
| ||||
| TfmroHtuLocalTable | 1.3.6.1.4.1.1887.1.1.4.3.3.2 | NA | mandatory | |
| RfmroHtuLocalEntry | 1.3.6.1.4.1.1887.1.1.4.3.3.2.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CfmroHtuLocalPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.3.2.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CfmroHtuLocalLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.3.2.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CfmroHtuLocalU1 | 1.3.6.1.4.1.1887.1.1.4.3.3.2.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory HDSL Error on Path 1 1 None No Alarm 4 BER6 Bit Error Ratio 10^-6 5 BER3 Bit Error Ratio 10^-3 9 LOS Loss of Signal 19 LOSW Loss of SDSL synchronistation 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuLocalU2 | 1.3.6.1.4.1.1887.1.1.4.3.3.2.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory HDSL Error on Path 2 1 None No Alarm 4 BER6 Bit Error Ratio 10^-6 5 BER3 Bit Error Ratio 10^-3 9 LOS Loss of Signal 19 LOSW Loss of SDSL synchronistation 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuLocalU | 1.3.6.1.4.1.1887.1.1.4.3.3.2.1.5 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error in 2MB Signal on HDSL Path 1 None No Alarm 4 BER6 Bit Error Ratio 10^-6 5 BER3 Bit Error Ratio 10^-3 7 AIS Alarm Indication Signal 8 LFA Loss of Frame Alignment 9 LOS Loss of Signal 10 RAI Remote Alarm Indication 18 BwNotAvail Bandwidth not available 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuLocalT | 1.3.6.1.4.1.1887.1.1.4.3.3.2.1.6 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error on the G.703 Interface 1 None No Alarm 4 BER6 Bit Error Ratio 10^-6 5 BER3 Bit Error Ratio 10^-3 7 AIS Alarm Indication Signal 8 LFA Loss of Frame Alignment 9 LOS Loss of Signal 11 RAI Remote Alarm Indication 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuLocalDC | 1.3.6.1.4.1.1887.1.1.4.3.3.2.1.7 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error on the Data interface (Transmit signal) 1 None No Alarm 6 LOA Loss of Activity 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuLocalDN | 1.3.6.1.4.1.1887.1.1.4.3.3.2.1.8 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error on the Data interface (Receive signal) 1 None No Alarm 6 LOA Loss of Activity 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuLocalEquipment | 1.3.6.1.4.1.1887.1.1.4.3.3.2.1.9 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Equipment Alarm 1 None No Alarm 10 Alarm Alarm present 25 XFW Firmware Mismatch 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuLocalLosD | 1.3.6.1.4.1.1887.1.1.4.3.3.2.1.10 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory LOS-D Error State 1 None No Alarm 10 Alarm Alarm present 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuLocalT3In | 1.3.6.1.4.1.1887.1.1.4.3.3.2.1.11 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Loss of Clock on T3In 1 None No Alarm 9 LOS Loss of Clock Signal an T3In 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuLocalRps | 1.3.6.1.4.1.1887.1.1.4.3.3.2.1.12 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Remote Power Supply Error State 1 None No Alarm 12 UCR12 Undercurrent on HDSL Path 1 and 2 13 UCR1 Undercurrent on HDSL Path 1 14 UCR2 Undercurrent on HDSL Path 2 15 OVR Overload 16 NOSYM Unsymetrical Load 17 DEFECT Defect on Module 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuLocalRta | 1.3.6.1.4.1.1887.1.1.4.3.3.2.1.13 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Remote Terminal Alarm Error State 1 None No Alarm 10 Alarm Alarm present 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuLocalPowerfail | 1.3.6.1.4.1.1887.1.1.4.3.3.2.1.14 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Remote Device Powerfailure Alarm. If this alarm occurs the remote device has lost all power and cannot be reached any longer. 1 None No Alarm 10 Alarm Alarm present 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuLocalT3Out | 1.3.6.1.4.1.1887.1.1.4.3.3.2.1.15 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory No Clock Signal available for T3Out 1 None No Alarm 9 LOS Loss of Clock Signal on T3Out 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuLocalLaser | 1.3.6.1.4.1.1887.1.1.4.3.3.2.1.16 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Laser aging alarm 1 None No Alarm 10 Alarm Laser reaching critical age 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuLocalAlarmSummary | 1.3.6.1.4.1.1887.1.1.4.3.3.2.1.17 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Contains the alarm summary of the link. This value is bit coded: Bit Value 0 1 UA Urgent alarm 1 2 NUA Non urgent alarm 2 4 AIS Alarm indication signal A value of 0 means no alarm | ||||
| CfmroHtuLocalPowerfailCpe | 1.3.6.1.4.1.1887.1.1.4.3.3.2.1.18 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Remote Device Local Power Loss Alarm. If this Alarm is active, the device has lost its local power supply but is still powered over the transmission line (using a remote power supply (RPS). 1 None No Alarm 10 Alarm Alarm present 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuLocalU3 | 1.3.6.1.4.1.1887.1.1.4.3.3.2.1.19 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory xDSL Error on Path 3 1 None No Alarm 4 BER6 Bit Error Ratio 10^-6 5 BER3 Bit Error Ratio 10^-3 9 LOS Loss of Signal 19 LOSW Loss of SDSL synchronistation 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuLocalU4 | 1.3.6.1.4.1.1887.1.1.4.3.3.2.1.20 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory xDSL Error on Path 4 1 None No Alarm 4 BER6 Bit Error Ratio 10^-6 5 BER3 Bit Error Ratio 10^-3 9 LOS Loss of Signal 19 LOSW Loss of SDSL synchronistation 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuLocalRps2 | 1.3.6.1.4.1.1887.1.1.4.3.3.2.1.21 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Remote Power Supply Error State on Path 2 1 None No Alarm 13 UCR1 Undercurrent on current Path 15 OVR Overload 16 NOSYM Unsymetrical Load 17 DEFECT Defect on Module 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuLocalRps3 | 1.3.6.1.4.1.1887.1.1.4.3.3.2.1.22 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Remote Power Supply Error State on Path 3 1 None No Alarm 13 UCR1 Undercurrent on current Path 15 OVR Overload 16 NOSYM Unsymetrical Load 17 DEFECT Defect on Module 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuLocalRps4 | 1.3.6.1.4.1.1887.1.1.4.3.3.2.1.23 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Remote Power Supply Error State on Path 4 1 None No Alarm 13 UCR1 Undercurrent on current Path 15 OVR Overload 16 NOSYM Unsymetrical Load 17 DEFECT Defect on Module 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuLocalVA | 1.3.6.1.4.1.1887.1.1.4.3.3.2.1.24 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error on the G.703 Interface 1 None No Alarm 4 BER6 Bit Error Ratio 10^-6 5 BER3 Bit Error Ratio 10^-3 7 AIS Alarm Indication Signal 8 LFA Loss of Frame Alignment 9 LOS Loss of Signal 11 RAI Remote Alarm Indication 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuLocalVB | 1.3.6.1.4.1.1887.1.1.4.3.3.2.1.25 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error on the G.703 Interface 1 None No Alarm 4 BER6 Bit Error Ratio 10^-6 5 BER3 Bit Error Ratio 10^-3 7 AIS Alarm Indication Signal 8 LFA Loss of Frame Alignment 9 LOS Loss of Signal 11 RAI Remote Alarm Indication 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuLocalVC | 1.3.6.1.4.1.1887.1.1.4.3.3.2.1.26 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error on the G.703 Interface 1 None No Alarm 4 BER6 Bit Error Ratio 10^-6 5 BER3 Bit Error Ratio 10^-3 7 AIS Alarm Indication Signal 8 LFA Loss of Frame Alignment 9 LOS Loss of Signal 11 RAI Remote Alarm Indication 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuLocalVD | 1.3.6.1.4.1.1887.1.1.4.3.3.2.1.27 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error on the G.703 Interface 1 None No Alarm 4 BER6 Bit Error Ratio 10^-6 5 BER3 Bit Error Ratio 10^-3 7 AIS Alarm Indication Signal 8 LFA Loss of Frame Alignment 9 LOS Loss of Signal 11 RAI Remote Alarm Indication 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuLocalMcsCha | 1.3.6.1.4.1.1887.1.1.4.3.3.2.1.28 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error on the MCS Channel a 1 None No Alarm 4 BER6 Bit Error Ratio 10^-6 5 BER3 Bit Error Ratio 10^-3 21 LOM Loss Of MCS sync 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuLocalMcsChb | 1.3.6.1.4.1.1887.1.1.4.3.3.2.1.29 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error on the MCS Channel b 1 None No Alarm 4 BER6 Bit Error Ratio 10^-6 5 BER3 Bit Error Ratio 10^-3 21 LOM Loss Of MCS sync 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuLocalMcsChc | 1.3.6.1.4.1.1887.1.1.4.3.3.2.1.30 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error on the MCS Channel c 1 None No Alarm 4 BER6 Bit Error Ratio 10^-6 5 BER3 Bit Error Ratio 10^-3 21 LOM Loss Of MCS sync 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuLocalMcsChd | 1.3.6.1.4.1.1887.1.1.4.3.3.2.1.31 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error on the MCS Channel d 1 None No Alarm 4 BER6 Bit Error Ratio 10^-6 5 BER3 Bit Error Ratio 10^-3 21 LOM Loss Of MCS sync 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuLocalMcsRemCha | 1.3.6.1.4.1.1887.1.1.4.3.3.2.1.32 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error on the MCS Remote Channel a 1 None No Alarm 21 LOM Loss Of MCS sync 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuLocalMcsRemChb | 1.3.6.1.4.1.1887.1.1.4.3.3.2.1.33 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error on the MCS Remote Channel b 1 None No Alarm 21 LOM Loss Of MCS sync 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuLocalMcsRemChc | 1.3.6.1.4.1.1887.1.1.4.3.3.2.1.34 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error on the MCS Remote Channel c 1 None No Alarm 21 LOM Loss Of MCS sync 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuLocalMcsRemChd | 1.3.6.1.4.1.1887.1.1.4.3.3.2.1.35 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error on the MCS Remote Channel d 1 None No Alarm 21 LOM Loss Of MCS sync 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuLocalMcs | 1.3.6.1.4.1.1887.1.1.4.3.3.2.1.36 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error on the entire MCS System 1 None No Alarm 21 LOM Loss Of MCS sync 22 PLOM Partial Loss Of MCS sync 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuLocalL2SwitchWanRx | 1.3.6.1.4.1.1887.1.1.4.3.3.2.1.37 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error on the L2Switch WAN interface (Receive signal) 1 None No Alarm 6 LOA Loss Of Activity 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuLocalL2SwitchWanTx | 1.3.6.1.4.1.1887.1.1.4.3.3.2.1.38 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error on the L2Switch WAN interface (Transmit signal) 1 None No Alarm 6 LOA Loss Of Activity 23 MIR Maximum Information Rate 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuLocalL2SwitchLanPort1 | 1.3.6.1.4.1.1887.1.1.4.3.3.2.1.39 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error on the L2Switch LAN Port 1 1 None No Alarm 24 LinkDown No Link Detected 27 LFP Link Failure Propagation 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuLocalL2SwitchLanPort2 | 1.3.6.1.4.1.1887.1.1.4.3.3.2.1.40 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error on the L2Switch LAN Port 2 1 None No Alarm 24 LinkDown No Link Detected 27 LFP Link Failure Propagation 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuLocalL2SwitchLanPort3 | 1.3.6.1.4.1.1887.1.1.4.3.3.2.1.41 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error on the L2Switch LAN Port 3 1 None No Alarm 24 LinkDown No Link Detected 27 LFP Link Failure Propagation 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuLocalL2SwitchLanPort4 | 1.3.6.1.4.1.1887.1.1.4.3.3.2.1.42 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error on the L2Switch LAN Port 4 1 None No Alarm 24 LinkDown No Link Detected 27 LFP Link Failure Propagation 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuLocalL2SwitchBPLPort1 | 1.3.6.1.4.1.1887.1.1.4.3.3.2.1.43 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error on the L2Switch Backplane Port 1 1 None No Alarm 24 LinkDown No Link Detected 27 LFP Link Failure Propagation 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuLocalUo | 1.3.6.1.4.1.1887.1.1.4.3.3.2.1.44 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error on the optical link 1 None No Alarm 9 LOS Loss of Signal 28 FAIL_UO1 Line protection fail on Uo1 29 FAIL_UO2 Line protection fail on Uo2 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuLocalUo1 | 1.3.6.1.4.1.1887.1.1.4.3.3.2.1.45 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error on first optical interface 1 None No Alarm 4 BER6 Bit Error Ratio 10^-6 5 BER3 Bit Error Ratio 10^-3 8 LFA Loss of Frame Alignment 9 LOS Loss of Signal 11 RAI Remote Alarm Indication 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuLocalUo2 | 1.3.6.1.4.1.1887.1.1.4.3.3.2.1.46 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error on second optical interface 1 None No Alarm 4 BER6 Bit Error Ratio 10^-6 5 BER3 Bit Error Ratio 10^-3 8 LFA Loss of Frame Alignment 9 LOS Loss of Signal 11 RAI Remote Alarm Indication 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuLocalUA | 1.3.6.1.4.1.1887.1.1.4.3.3.2.1.47 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error in 2MB Signal (Framer A) on transmission side 1 None No Alarm 4 BER6 Bit Error Ratio 10^-6 5 BER3 Bit Error Ratio 10^-3 7 AIS Alarm Indication Signal 8 LFA Loss of Frame Alignment 9 LOS Loss of Signal 11 RAI Remote Alarm Indication 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuLocalUB | 1.3.6.1.4.1.1887.1.1.4.3.3.2.1.48 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error in 2MB Signal (Framer B) on transmission side 1 None No Alarm 4 BER6 Bit Error Ratio 10^-6 5 BER3 Bit Error Ratio 10^-3 7 AIS Alarm Indication Signal 8 LFA Loss of Frame Alignment 9 LOS Loss of Signal 11 RAI Remote Alarm Indication 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuLocalUC | 1.3.6.1.4.1.1887.1.1.4.3.3.2.1.49 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error in 2MB Signal (Framer C) on transmission side 1 None No Alarm 4 BER6 Bit Error Ratio 10^-6 5 BER3 Bit Error Ratio 10^-3 7 AIS Alarm Indication Signal 8 LFA Loss of Frame Alignment 9 LOS Loss of Signal 11 RAI Remote Alarm Indication 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuLocalUD | 1.3.6.1.4.1.1887.1.1.4.3.3.2.1.50 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error in 2MB Signal (Framer D) on transmission side 1 None No Alarm 4 BER6 Bit Error Ratio 10^-6 5 BER3 Bit Error Ratio 10^-3 7 AIS Alarm Indication Signal 8 LFA Loss of Frame Alignment 9 LOS Loss of Signal 11 RAI Remote Alarm Indication 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuLocalLosDB | 1.3.6.1.4.1.1887.1.1.4.3.3.2.1.51 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory LOS-D (Framer B) Error State 1 None No Alarm 10 Alarm Alarm present 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuLocalLosDC | 1.3.6.1.4.1.1887.1.1.4.3.3.2.1.52 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory LOS-D (Framer C) Error State 1 None No Alarm 10 Alarm Alarm present 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuLocalLosDD | 1.3.6.1.4.1.1887.1.1.4.3.3.2.1.53 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory LOS-D (Framer D) Error State 1 None No Alarm 10 Alarm Alarm present 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuLocalSFP1 | 1.3.6.1.4.1.1887.1.1.4.3.3.2.1.54 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error on first SFP modul 1 None No Alarm 30 Tx fault Transmit laser fault 31 Invalid Invalid SFP modul equipped 32 Missing No SFP modul equipped 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuLocalSFP2 | 1.3.6.1.4.1.1887.1.1.4.3.3.2.1.55 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error on second SFP modul 1 None No Alarm 30 Tx fault Transmit laser fault 31 Invalid Invalid SFP modul equipped 32 Missing No SFP modul equipped 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| TfmroHtuFarTable | 1.3.6.1.4.1.1887.1.1.4.3.3.3 | NA | mandatory | |
| RfmroHtuFarEntry | 1.3.6.1.4.1.1887.1.1.4.3.3.3.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CfmroHtuFarPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.3.3.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CfmroHtuFarLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.3.3.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CfmroHtuFarU1 | 1.3.6.1.4.1.1887.1.1.4.3.3.3.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory HDSL Error on Path 1 1 None No Alarm 4 BER6 Bit Error Ratio 10^-6 5 BER3 Bit Error Ratio 10^-3 9 LOS Loss of Signal 19 LOSW Loss of SDSL synchronistation 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuFarU2 | 1.3.6.1.4.1.1887.1.1.4.3.3.3.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory HDSL Error on Path 2 1 None No Alarm 4 BER6 Bit Error Ratio 10^-6 5 BER3 Bit Error Ratio 10^-3 9 LOS Loss of Signal 19 LOSW Loss of SDSL synchronistation 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuFarU | 1.3.6.1.4.1.1887.1.1.4.3.3.3.1.5 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error in 2MB Signal on HDSL Path 1 None No Alarm 4 BER6 Bit Error Ratio 10^-6 5 BER3 Bit Error Ratio 10^-3 7 AIS Alarm Indication Signal 8 LFA Loss of Frame Alignment 9 LOS Loss of Signal 11 RAI Remote Alarm Indication 18 BwNotAvail Bandwidth not available 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuFarT | 1.3.6.1.4.1.1887.1.1.4.3.3.3.1.6 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error on the G.703 Interface 1 None No Alarm 4 BER6 Bit Error Ratio 10^-6 5 BER3 Bit Error Ratio 10^-3 7 AIS Alarm Indication Signal 8 LFA Loss of Frame Alignment 9 LOS Loss of Signal 11 RAI Remote Alarm Indication 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuFarDC | 1.3.6.1.4.1.1887.1.1.4.3.3.3.1.7 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error on the Data interface (Transmit signal) 1 None No Alarm 6 LOA Loss of Activity 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuFarDN | 1.3.6.1.4.1.1887.1.1.4.3.3.3.1.8 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error on the Data interface (Receive signal) 1 None No Alarm 6 LOA Loss of Activity 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuFarEquipment | 1.3.6.1.4.1.1887.1.1.4.3.3.3.1.9 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Equipment Alarm 1 None No Alarm 10 Alarm Alarm present 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuFarLosD | 1.3.6.1.4.1.1887.1.1.4.3.3.3.1.10 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory LOS-D Error State 1 None No Alarm 10 Alarm Alarm present 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuFarT3In | 1.3.6.1.4.1.1887.1.1.4.3.3.3.1.11 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Loss of Clock on T3In 1 None No Alarm 9 LOS Loss of Clock Signal on T3In 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuFarRps | 1.3.6.1.4.1.1887.1.1.4.3.3.3.1.12 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Remote Power Supply Error State 1 None No Alarm 12 UCR12 Undercurrent on HDSL Path 1 and 2 13 UCR1 Undercurrent on HDSL Path 1 14 UCR2 Undercurrent on HDSL Path 2 15 OVR Overload 16 NOSYM Unsymetrical Load 17 DEFECT Defect on Module 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuFarRta | 1.3.6.1.4.1.1887.1.1.4.3.3.3.1.13 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Remote Terminal Alarm Error State 1 None No Alarm 10 Alarm Alarm present 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuFarPowerfail | 1.3.6.1.4.1.1887.1.1.4.3.3.3.1.14 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Remote Device Powerfailure Alarm 1 None No Alarm 10 Alarm Alarm present 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuFarT3Out | 1.3.6.1.4.1.1887.1.1.4.3.3.3.1.15 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory No Clock Signal available for T3Out 1 None No Alarm 9 LOS Loss of Clock Signal on T3Out 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuFarLaser | 1.3.6.1.4.1.1887.1.1.4.3.3.3.1.16 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Laser aging alarm 1 None No Alarm 10 Alarm Laser reaching critcal age 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuFarPowerfailCpe | 1.3.6.1.4.1.1887.1.1.4.3.3.3.1.17 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Remote Device Local Power Loss Alarm. If this Alarm is active, the device has lost its local power supply but is still powered over the transmission line (using a remote power supply (RPS). 1 None No Alarm 10 Alarm Alarm present 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuFarU3 | 1.3.6.1.4.1.1887.1.1.4.3.3.3.1.18 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory xDSL Error on Path 3 1 None No Alarm 4 BER6 Bit Error Ratio 10^-6 5 BER3 Bit Error Ratio 10^-3 9 LOS Loss of Signal 19 LOSW Loss of SDSL synchronistation 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuFarU4 | 1.3.6.1.4.1.1887.1.1.4.3.3.3.1.19 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory xDSL Error on Path 4 1 None No Alarm 4 BER6 Bit Error Ratio 10^-6 5 BER3 Bit Error Ratio 10^-3 9 LOS Loss of Signal 19 LOSW Loss of SDSL synchronistation 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuFarRps2 | 1.3.6.1.4.1.1887.1.1.4.3.3.3.1.20 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Remote Power Supply Error State on Path 2 1 None No Alarm 13 UCR1 Undercurrent on current Path 15 OVR Overload 16 NOSYM Unsymetrical Load 17 DEFECT Defect on Module 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuFarRps3 | 1.3.6.1.4.1.1887.1.1.4.3.3.3.1.21 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Remote Power Supply Error State on Path 3 1 None No Alarm 13 UCR1 Undercurrent on current Path 15 OVR Overload 16 NOSYM Unsymetrical Load 17 DEFECT Defect on Module 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuFarRps4 | 1.3.6.1.4.1.1887.1.1.4.3.3.3.1.22 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Remote Power Supply Error State on Path 4 1 None No Alarm 13 UCR1 Undercurrent on current Path 15 OVR Overload 16 NOSYM Unsymetrical Load 17 DEFECT Defect on Module 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuFarVSlave | 1.3.6.1.4.1.1887.1.1.4.3.3.3.1.23 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error on the V-Interface on the slave device 1 None No Alarm 4 BER6 Bit Error Ratio 10^-6 5 BER3 Bit Error Ratio 10^-3 7 AIS Alarm Indication Signal 8 LFA Loss of Frame Alignment 9 LOS Loss of Signal 10 RAI Remote Alarm Indication 20 NSP No Slave Present (GTU with slave support) 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuFarTSlave | 1.3.6.1.4.1.1887.1.1.4.3.3.3.1.24 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error on the T-Interface on the slave device 1 None No Alarm 4 BER6 Bit Error Ratio 10^-6 5 BER3 Bit Error Ratio 10^-3 7 AIS Alarm Indication Signal 8 LFA Loss of Frame Alignment 9 LOS Loss of Signal 11 RAI Remote Alarm Indication 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuFarDCSlave | 1.3.6.1.4.1.1887.1.1.4.3.3.3.1.25 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error on the Data interface (Transmit signal) on the slave device 1 None No Alarm 6 LOA Loss of Activity 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuFarDNSlave | 1.3.6.1.4.1.1887.1.1.4.3.3.3.1.26 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error on the Data interface (Receive signal) on the slave device 1 None No Alarm 6 LOA Loss of Activity 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuFarVA | 1.3.6.1.4.1.1887.1.1.4.3.3.3.1.27 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error on the G.703 Interface 1 None No Alarm 4 BER6 Bit Error Ratio 10^-6 5 BER3 Bit Error Ratio 10^-3 7 AIS Alarm Indication Signal 8 LFA Loss of Frame Alignment 9 LOS Loss of Signal 11 RAI Remote Alarm Indication 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuFarVB | 1.3.6.1.4.1.1887.1.1.4.3.3.3.1.28 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error on the G.703 Interface 1 None No Alarm 4 BER6 Bit Error Ratio 10^-6 5 BER3 Bit Error Ratio 10^-3 7 AIS Alarm Indication Signal 8 LFA Loss of Frame Alignment 9 LOS Loss of Signal 11 RAI Remote Alarm Indication 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuFarVC | 1.3.6.1.4.1.1887.1.1.4.3.3.3.1.29 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error on the G.703 Interface 1 None No Alarm 4 BER6 Bit Error Ratio 10^-6 5 BER3 Bit Error Ratio 10^-3 7 AIS Alarm Indication Signal 8 LFA Loss of Frame Alignment 9 LOS Loss of Signal 11 RAI Remote Alarm Indication 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuFarVD | 1.3.6.1.4.1.1887.1.1.4.3.3.3.1.30 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error on the G.703 Interface 1 None No Alarm 4 BER6 Bit Error Ratio 10^-6 5 BER3 Bit Error Ratio 10^-3 7 AIS Alarm Indication Signal 8 LFA Loss of Frame Alignment 9 LOS Loss of Signal 11 RAI Remote Alarm Indication 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuFarMcsCha | 1.3.6.1.4.1.1887.1.1.4.3.3.3.1.31 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error on the MCS Channel a 1 None No Alarm 4 BER6 Bit Error Ratio 10^-6 5 BER3 Bit Error Ratio 10^-3 21 LOM Loss Of MCS sync 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuFarMcsChb | 1.3.6.1.4.1.1887.1.1.4.3.3.3.1.32 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error on the MCS Channel b 1 None No Alarm 4 BER6 Bit Error Ratio 10^-6 5 BER3 Bit Error Ratio 10^-3 21 LOM Loss Of MCS sync 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuFarMcsChc | 1.3.6.1.4.1.1887.1.1.4.3.3.3.1.33 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error on the MCS Channel c 1 None No Alarm 4 BER6 Bit Error Ratio 10^-6 5 BER3 Bit Error Ratio 10^-3 21 LOM Loss Of MCS sync 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuFarMcsChd | 1.3.6.1.4.1.1887.1.1.4.3.3.3.1.34 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error on the MCS Channel d 1 None No Alarm 4 BER6 Bit Error Ratio 10^-6 5 BER3 Bit Error Ratio 10^-3 21 LOM Loss Of MCS sync 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuFarMcsRemCha | 1.3.6.1.4.1.1887.1.1.4.3.3.3.1.35 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error on the MCS Remote Channel a 1 None No Alarm 21 LOM Loss Of MCS sync 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuFarMcsRemChb | 1.3.6.1.4.1.1887.1.1.4.3.3.3.1.36 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error on the MCS Remote Channel b 1 None No Alarm 21 LOM Loss Of MCS sync 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuFarMcsRemChc | 1.3.6.1.4.1.1887.1.1.4.3.3.3.1.37 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error on the MCS Remote Channel c 1 None No Alarm 21 LOM Loss Of MCS sync 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuFarMcsRemChd | 1.3.6.1.4.1.1887.1.1.4.3.3.3.1.38 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error on the MCS Remote Channel d 1 None No Alarm 21 LOM Loss Of MCS sync 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuFarMcs | 1.3.6.1.4.1.1887.1.1.4.3.3.3.1.39 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error on the entire MCS System 1 None No Alarm 21 LOM Loss Of MCS sync 22 PLOM Partial Loss Of MCS sync 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuFarL2SwitchWanRx | 1.3.6.1.4.1.1887.1.1.4.3.3.3.1.40 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error on the L2Switch WAN interface (Receive signal) 1 None No Alarm 6 LOA Loss Of Activity 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuFarL2SwitchWanTx | 1.3.6.1.4.1.1887.1.1.4.3.3.3.1.41 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error on the L2Switch WAN interface (Transmit signal) 1 None No Alarm 6 LOA Loss Of Activity 23 MIR Maximum Information Rate 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuFarL2SwitchLanPort1 | 1.3.6.1.4.1.1887.1.1.4.3.3.3.1.42 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error on the L2Switch LAN Port 1 1 None No Alarm 24 LinkDown No Link Detected 27 LFP Link Failure Propagation 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuFarL2SwitchLanPort2 | 1.3.6.1.4.1.1887.1.1.4.3.3.3.1.43 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error on the L2Switch LAN Port 2 1 None No Alarm 24 LinkDown No Link Detected 27 LFP Link Failure Propagation 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuFarL2SwitchLanPort3 | 1.3.6.1.4.1.1887.1.1.4.3.3.3.1.44 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error on the L2Switch LAN Port 3 1 None No Alarm 24 LinkDown No Link Detected 27 LFP Link Failure Propagation 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuFarL2SwitchLanPort4 | 1.3.6.1.4.1.1887.1.1.4.3.3.3.1.45 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error on the L2Switch LAN Port 4 1 None No Alarm 24 LinkDown No Link Detected 27 LFP Link Failure Propagation 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuFarL2SwitchBPLPort1 | 1.3.6.1.4.1.1887.1.1.4.3.3.3.1.46 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error on the L2Switch Backplane Port 1 1 None No Alarm 24 LinkDown No Link Detected 27 LFP Link Failure Propagation 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuFarUo | 1.3.6.1.4.1.1887.1.1.4.3.3.3.1.47 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error on the optical link 1 None No Alarm 9 LOS Loss of Signal 28 FAIL_UO1 Line protection fail on Uo1 29 FAIL_UO2 Line protection fail on Uo2 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuFarUo1 | 1.3.6.1.4.1.1887.1.1.4.3.3.3.1.48 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error on first optical interface 1 None No Alarm 4 BER6 Bit Error Ratio 10^-6 5 BER3 Bit Error Ratio 10^-3 8 LFA Loss of Frame Alignment 9 LOS Loss of Signal 11 RAI Remote Alarm Indication 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuFarUo2 | 1.3.6.1.4.1.1887.1.1.4.3.3.3.1.49 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error on second optical interface 1 None No Alarm 4 BER6 Bit Error Ratio 10^-6 5 BER3 Bit Error Ratio 10^-3 8 LFA Loss of Frame Alignment 9 LOS Loss of Signal 11 RAI Remote Alarm Indication 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuFarUA | 1.3.6.1.4.1.1887.1.1.4.3.3.3.1.50 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error in 2MB Signal (Framer A) on transmission side 1 None No Alarm 4 BER6 Bit Error Ratio 10^-6 5 BER3 Bit Error Ratio 10^-3 7 AIS Alarm Indication Signal 8 LFA Loss of Frame Alignment 11 RAI Remote Alarm Indication 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuFarUB | 1.3.6.1.4.1.1887.1.1.4.3.3.3.1.51 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error in 2MB Signal (Framer B) on transmission side 1 None No Alarm 4 BER6 Bit Error Ratio 10^-6 5 BER3 Bit Error Ratio 10^-3 7 AIS Alarm Indication Signal 8 LFA Loss of Frame Alignment 11 RAI Remote Alarm Indication 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuFarUC | 1.3.6.1.4.1.1887.1.1.4.3.3.3.1.52 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error in 2MB Signal (Framer C) on transmission side 1 None No Alarm 4 BER6 Bit Error Ratio 10^-6 5 BER3 Bit Error Ratio 10^-3 7 AIS Alarm Indication Signal 8 LFA Loss of Frame Alignment 11 RAI Remote Alarm Indication 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuFarUD | 1.3.6.1.4.1.1887.1.1.4.3.3.3.1.53 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error in 2MB Signal (Framer D) on transmission side 1 None No Alarm 4 BER6 Bit Error Ratio 10^-6 5 BER3 Bit Error Ratio 10^-3 7 AIS Alarm Indication Signal 8 LFA Loss of Frame Alignment 11 RAI Remote Alarm Indication 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuFarLosDB | 1.3.6.1.4.1.1887.1.1.4.3.3.3.1.54 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory LOS-D (Framer B) Error State 1 None No Alarm 10 Alarm Alarm present 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuFarLosDC | 1.3.6.1.4.1.1887.1.1.4.3.3.3.1.55 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory LOS-D (Framer C) Error State 1 None No Alarm 10 Alarm Alarm present 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuFarLosDD | 1.3.6.1.4.1.1887.1.1.4.3.3.3.1.56 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory LOS-D (Framer D) Error State 1 None No Alarm 10 Alarm Alarm present 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuFarSFP1 | 1.3.6.1.4.1.1887.1.1.4.3.3.3.1.57 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error on first SFP modul 1 None No Alarm 30 Tx fault Transmit laser fault 31 Invalid Invalid SFP modul equipped 32 Missing No SFP modul equipped 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroHtuFarSFP2 | 1.3.6.1.4.1.1887.1.1.4.3.3.3.1.58 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Error on second SFP modul 1 None No Alarm 30 Tx fault Transmit laser fault 31 Invalid Invalid SFP modul equipped 32 Missing No SFP modul equipped 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| TfmroRegTable | 1.3.6.1.4.1.1887.1.1.4.3.3.4 | NA | mandatory | |
| RfmroRegEntry | 1.3.6.1.4.1.1887.1.1.4.3.3.4.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CfmroRegPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.3.4.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CfmroRegLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.3.4.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CfmroRegSectionIndex | 1.3.6.1.4.1.1887.1.1.4.3.3.4.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Defines which Section of Regenerators is to be queried. Ulaf+ Version 1.0 only supports the first section. 1 sectionA First section 2 sectionB Second section
| ||||
| CfmroRegU1L | 1.3.6.1.4.1.1887.1.1.4.3.3.4.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Regenerator Error on HDSL Path 1 to LT 1 None No Alarm 4 BER6 Bit Error Ratio 10^-6 5 BER3 Bit Error Ratio 10^-3 9 LOS Loss of Signal 19 LOSW Loss of SDSL synchronistation 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroRegU2L | 1.3.6.1.4.1.1887.1.1.4.3.3.4.1.5 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Regenerator Error on HDSL Path 2 to LT 1 None No Alarm 4 BER6 Bit Error Ratio 10^-6 5 BER3 Bit Error Ratio 10^-3 9 LOS Loss of Signal 19 LOSW Loss of SDSL synchronistation 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroRegU1N | 1.3.6.1.4.1.1887.1.1.4.3.3.4.1.6 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Regenerator Error on HDSL Path 1 to NT 1 None No Alarm 4 BER6 Bit Error Ratio 10^-6 5 BER3 Bit Error Ratio 10^-3 9 LOS Loss of Signal 19 LOSW Loss of SDSL synchronistation 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroRegU2N | 1.3.6.1.4.1.1887.1.1.4.3.3.4.1.7 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Regenerator Error on HDSL Path 2 to NT 1 None No Alarm 4 BER6 Bit Error Ratio 10^-6 5 BER3 Bit Error Ratio 10^-3 9 LOS Loss of Signal 19 LOSW Loss of SDSL synchronistation 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroRegEquipment1 | 1.3.6.1.4.1.1887.1.1.4.3.3.4.1.8 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Equipment Alarm in Regenerator in HDSL Path 1 1 None No Alarm 10 Alarm Equipment Alarm present 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroRegEquipment2 | 1.3.6.1.4.1.1887.1.1.4.3.3.4.1.9 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Equipment Alarm in Regenerator in HDSL Path 2 1 None No Alarm 10 Alarm Equipment Alarm present 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| TfmroLocalLedStateTable | 1.3.6.1.4.1.1887.1.1.4.3.3.5 | NA | mandatory | |
| RfmroLocalLedStateEntry | 1.3.6.1.4.1.1887.1.1.4.3.3.5.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CfmroLocalLedStatePortIndex | 1.3.6.1.4.1.1887.1.1.4.3.3.5.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CfmroLocalLedStateLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.3.5.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CfmroLocalLedState1 | 1.3.6.1.4.1.1887.1.1.4.3.3.5.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory State of LED1 of the device. HTU: Loop / Maintenance 1 Off 2 On 3 Blinking pattern 1 4 Blinking pattern 2 5 Blinking pattern 3 6 Blinking pattern 4 7 Blinking pattern 5
| ||||
| CfmroLocalLedState2 | 1.3.6.1.4.1.1887.1.1.4.3.3.5.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory State of LED2 of the device. HTU: LOS/LFA-U 1 Off 2 On 3 Blinking pattern 1 4 Blinking pattern 2 5 Blinking pattern 3 6 Blinking pattern 4 7 Blinking pattern 5
| ||||
| CfmroLocalLedState3 | 1.3.6.1.4.1.1887.1.1.4.3.3.5.1.5 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory State of LED3 of the device. HTU: LOS/LFA-T 1 Off 2 On 3 Blinking pattern 1 4 Blinking pattern 2 5 Blinking pattern 3 6 Blinking pattern 4 7 Blinking pattern 5
| ||||
| CfmroLocalLedState4 | 1.3.6.1.4.1.1887.1.1.4.3.3.5.1.6 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory State of LED4 of the device. HTU: AIS-U 1 Off 2 On 3 Blinking pattern 1 4 Blinking pattern 2 5 Blinking pattern 3 6 Blinking pattern 4 7 Blinking pattern 5
| ||||
| CfmroLocalLedState5 | 1.3.6.1.4.1.1887.1.1.4.3.3.5.1.7 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory State of LED5 of the device. HTU: BER6-U 1 Off 2 On 3 Blinking pattern 1 4 Blinking pattern 2 5 Blinking pattern 3 6 Blinking pattern 4 7 Blinking pattern 5
| ||||
| CfmroLocalLedState6 | 1.3.6.1.4.1.1887.1.1.4.3.3.5.1.8 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory State of LED6 of the device. HTU: PRA (Desktop only) 1 Off 2 On 3 Blinking pattern 1 4 Blinking pattern 2 5 Blinking pattern 3 6 Blinking pattern 4 7 Blinking pattern 5
| ||||
| CfmroLocalLedState7 | 1.3.6.1.4.1.1887.1.1.4.3.3.5.1.9 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory State of LED7 of the device. HTU: LOA-R (Desktop only) 1 Off 2 On 3 Blinking pattern 1 4 Blinking pattern 2 5 Blinking pattern 3 6 Blinking pattern 4 7 Blinking pattern 5
| ||||
| CfmroLocalLedState8 | 1.3.6.1.4.1.1887.1.1.4.3.3.5.1.10 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory State of LED8 of the device. HTU: LOA-T (Desktop only) 1 Off 2 On 3 Blinking pattern 1 4 Blinking pattern 2 5 Blinking pattern 3 6 Blinking pattern 4 7 Blinking pattern 5
| ||||
| CfmroLocalLedState9 | 1.3.6.1.4.1.1887.1.1.4.3.3.5.1.11 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory State of LED9 of the device. 1 Off 2 On 3 Blinking pattern 1 4 Blinking pattern 2 5 Blinking pattern 3 6 Blinking pattern 4 7 Blinking pattern 5
| ||||
| CfmroLocalLedState10 | 1.3.6.1.4.1.1887.1.1.4.3.3.5.1.12 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory State of LED10 of the device. 1 Off 2 On 3 Blinking pattern 1 4 Blinking pattern 2 5 Blinking pattern 3 6 Blinking pattern 4 7 Blinking pattern 5
| ||||
| CfmroLocalLedColor1 | 1.3.6.1.4.1.1887.1.1.4.3.3.5.1.13 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Color of LED1 of the device. 1 LED color is black 2 LED color is yellow 3 LED color is red 4 LED color is green
| ||||
| CfmroLocalLedColor2 | 1.3.6.1.4.1.1887.1.1.4.3.3.5.1.14 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Color of LED2 of the device. 1 LED color is black 2 LED color is yellow 3 LED color is red 4 LED color is green
| ||||
| CfmroLocalLedColor3 | 1.3.6.1.4.1.1887.1.1.4.3.3.5.1.15 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Color of LED3 of the device. 1 LED color is black 2 LED color is yellow 3 LED color is red 4 LED color is green
| ||||
| CfmroLocalLedColor4 | 1.3.6.1.4.1.1887.1.1.4.3.3.5.1.16 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Color of LED4 of the device. 1 LED color is black 2 LED color is yellow 3 LED color is red 4 LED color is green
| ||||
| CfmroLocalLedColor5 | 1.3.6.1.4.1.1887.1.1.4.3.3.5.1.17 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Color of LED5 of the device. 1 LED color is black 2 LED color is yellow 3 LED color is red 4 LED color is green
| ||||
| CfmroLocalLedColor6 | 1.3.6.1.4.1.1887.1.1.4.3.3.5.1.18 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Color of LED6 of the device. 1 LED color is black 2 LED color is yellow 3 LED color is red 4 LED color is green
| ||||
| CfmroLocalLedColor7 | 1.3.6.1.4.1.1887.1.1.4.3.3.5.1.19 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Color of LED7 of the device. 1 LED color is black 2 LED color is yellow 3 LED color is red 4 LED color is green
| ||||
| CfmroLocalLedColor8 | 1.3.6.1.4.1.1887.1.1.4.3.3.5.1.20 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Color of LED8 of the device. 1 LED color is black 2 LED color is yellow 3 LED color is red 4 LED color is green
| ||||
| CfmroLocalLedColor9 | 1.3.6.1.4.1.1887.1.1.4.3.3.5.1.21 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Color of LED9 of the device. 1 LED color is black 2 LED color is yellow 3 LED color is red 4 LED color is green
| ||||
| CfmroLocalLedColor10 | 1.3.6.1.4.1.1887.1.1.4.3.3.5.1.22 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Color of LED10 of the device. 1 LED color is black 2 LED color is yellow 3 LED color is red 4 LED color is green
| ||||
| CfmroLocalLedState11 | 1.3.6.1.4.1.1887.1.1.4.3.3.5.1.23 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory State of LED11 of the device. 1 Off 2 On 3 Blinking pattern 1 4 Blinking pattern 2 5 Blinking pattern 3 6 Blinking pattern 4 7 Blinking pattern 5
| ||||
| CfmroLocalLedState12 | 1.3.6.1.4.1.1887.1.1.4.3.3.5.1.24 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory State of LED12 of the device. 1 Off 2 On 3 Blinking pattern 1 4 Blinking pattern 2 5 Blinking pattern 3 6 Blinking pattern 4 7 Blinking pattern 5
| ||||
| CfmroLocalLedState13 | 1.3.6.1.4.1.1887.1.1.4.3.3.5.1.25 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory State of LED13 of the device. 1 Off 2 On 3 Blinking pattern 1 4 Blinking pattern 2 5 Blinking pattern 3 6 Blinking pattern 4 7 Blinking pattern 5
| ||||
| CfmroLocalLedState14 | 1.3.6.1.4.1.1887.1.1.4.3.3.5.1.26 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory State of LED14 of the device. 1 Off 2 On 3 Blinking pattern 1 4 Blinking pattern 2 5 Blinking pattern 3 6 Blinking pattern 4 7 Blinking pattern 5
| ||||
| CfmroLocalLedState15 | 1.3.6.1.4.1.1887.1.1.4.3.3.5.1.27 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory State of LED15 of the device. 1 Off 2 On 3 Blinking pattern 1 4 Blinking pattern 2 5 Blinking pattern 3 6 Blinking pattern 4 7 Blinking pattern 5
| ||||
| CfmroLocalLedState16 | 1.3.6.1.4.1.1887.1.1.4.3.3.5.1.28 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory State of LED16 of the device. 1 Off 2 On 3 Blinking pattern 1 4 Blinking pattern 2 5 Blinking pattern 3 6 Blinking pattern 4 7 Blinking pattern 5
| ||||
| CfmroLocalLedState17 | 1.3.6.1.4.1.1887.1.1.4.3.3.5.1.29 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory State of LED17 of the device. 1 Off 2 On 3 Blinking pattern 1 4 Blinking pattern 2 5 Blinking pattern 3 6 Blinking pattern 4 7 Blinking pattern 5
| ||||
| CfmroLocalLedState18 | 1.3.6.1.4.1.1887.1.1.4.3.3.5.1.30 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory State of LED18 of the device. 1 Off 2 On 3 Blinking pattern 1 4 Blinking pattern 2 5 Blinking pattern 3 6 Blinking pattern 4 7 Blinking pattern 5
| ||||
| CfmroLocalLedState19 | 1.3.6.1.4.1.1887.1.1.4.3.3.5.1.31 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory State of LED19 of the device. 1 Off 2 On 3 Blinking pattern 1 4 Blinking pattern 2 5 Blinking pattern 3 6 Blinking pattern 4 7 Blinking pattern 5
| ||||
| CfmroLocalLedState20 | 1.3.6.1.4.1.1887.1.1.4.3.3.5.1.32 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory State of LED20 of the device. 1 Off 2 On 3 Blinking pattern 1 4 Blinking pattern 2 5 Blinking pattern 3 6 Blinking pattern 4 7 Blinking pattern 5
| ||||
| CfmroLocalLedColor11 | 1.3.6.1.4.1.1887.1.1.4.3.3.5.1.33 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Color of LED11 of the device. 1 LED color is black 2 LED color is yellow 3 LED color is red 4 LED color is green
| ||||
| CfmroLocalLedColor12 | 1.3.6.1.4.1.1887.1.1.4.3.3.5.1.34 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Color of LED12 of the device. 1 LED color is black 2 LED color is yellow 3 LED color is red 4 LED color is green
| ||||
| CfmroLocalLedColor13 | 1.3.6.1.4.1.1887.1.1.4.3.3.5.1.35 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Color of LED13 of the device. 1 LED color is black 2 LED color is yellow 3 LED color is red 4 LED color is green
| ||||
| CfmroLocalLedColor14 | 1.3.6.1.4.1.1887.1.1.4.3.3.5.1.36 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Color of LED14 of the device. 1 LED color is black 2 LED color is yellow 3 LED color is red 4 LED color is green
| ||||
| CfmroLocalLedColor15 | 1.3.6.1.4.1.1887.1.1.4.3.3.5.1.37 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Color of LED15 of the device. 1 LED color is black 2 LED color is yellow 3 LED color is red 4 LED color is green
| ||||
| CfmroLocalLedColor16 | 1.3.6.1.4.1.1887.1.1.4.3.3.5.1.38 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Color of LED16 of the device. 1 LED color is black 2 LED color is yellow 3 LED color is red 4 LED color is green
| ||||
| CfmroLocalLedColor17 | 1.3.6.1.4.1.1887.1.1.4.3.3.5.1.39 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Color of LED17 of the device. 1 LED color is black 2 LED color is yellow 3 LED color is red 4 LED color is green
| ||||
| CfmroLocalLedColor18 | 1.3.6.1.4.1.1887.1.1.4.3.3.5.1.40 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Color of LED18 of the device. 1 LED color is black 2 LED color is yellow 3 LED color is red 4 LED color is green
| ||||
| CfmroLocalLedColor19 | 1.3.6.1.4.1.1887.1.1.4.3.3.5.1.41 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Color of LED19 of the device. 1 LED color is black 2 LED color is yellow 3 LED color is red 4 LED color is green
| ||||
| CfmroLocalLedColor20 | 1.3.6.1.4.1.1887.1.1.4.3.3.5.1.42 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Color of LED20 of the device. 1 LED color is black 2 LED color is yellow 3 LED color is red 4 LED color is green
| ||||
| TfmroFarLedStateTable | 1.3.6.1.4.1.1887.1.1.4.3.3.6 | NA | mandatory | |
| RfmroFarLedStateEntry | 1.3.6.1.4.1.1887.1.1.4.3.3.6.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CfmroFarLedStatePortIndex | 1.3.6.1.4.1.1887.1.1.4.3.3.6.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CfmroFarLedStateLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.3.6.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CfmroFarLedState1 | 1.3.6.1.4.1.1887.1.1.4.3.3.6.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory State of LED1 of the device. HTU: Loop / Maintenance 1 Off 2 On 3 Blinking pattern 1 4 Blinking pattern 2 5 Blinking pattern 3 6 Blinking pattern 4 7 Blinking pattern 5
| ||||
| CfmroFarLedState2 | 1.3.6.1.4.1.1887.1.1.4.3.3.6.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory State of LED2 of the device. HTU: LOS/LFA-U 1 Off 2 On 3 Blinking pattern 1 4 Blinking pattern 2 5 Blinking pattern 3 6 Blinking pattern 4 7 Blinking pattern 5
| ||||
| CfmroFarLedState3 | 1.3.6.1.4.1.1887.1.1.4.3.3.6.1.5 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory State of LED3 of the device. HTU: LOS/LFA-T 1 Off 2 On 3 Blinking pattern 1 4 Blinking pattern 2 5 Blinking pattern 3 6 Blinking pattern 4 7 Blinking pattern 5
| ||||
| CfmroFarLedState4 | 1.3.6.1.4.1.1887.1.1.4.3.3.6.1.6 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory State of LED4 of the device. HTU: AIS-U 1 Off 2 On 3 Blinking pattern 1 4 Blinking pattern 2 5 Blinking pattern 3 6 Blinking pattern 4 7 Blinking pattern 5
| ||||
| CfmroFarLedState5 | 1.3.6.1.4.1.1887.1.1.4.3.3.6.1.7 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory State of LED5 of the device. HTU: BER6-U 1 Off 2 On 3 Blinking pattern 1 4 Blinking pattern 2 5 Blinking pattern 3 6 Blinking pattern 4 7 Blinking pattern 5
| ||||
| CfmroFarLedState6 | 1.3.6.1.4.1.1887.1.1.4.3.3.6.1.8 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory State of LED6 of the device. HTU: PRA (Desktop only) 1 Off 2 On 3 Blinking pattern 1 4 Blinking pattern 2 5 Blinking pattern 3 6 Blinking pattern 4 7 Blinking pattern 5
| ||||
| CfmroFarLedState7 | 1.3.6.1.4.1.1887.1.1.4.3.3.6.1.9 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory State of LED7 of the device. HTU: LOA-R (Desktop only) 1 Off 2 On 3 Blinking pattern 1 4 Blinking pattern 2 5 Blinking pattern 3 6 Blinking pattern 4 7 Blinking pattern 5
| ||||
| CfmroFarLedState8 | 1.3.6.1.4.1.1887.1.1.4.3.3.6.1.10 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory State of LED8 of the device. HTU: LOA-T (Desktop only) 1 Off 2 On 3 Blinking pattern 1 4 Blinking pattern 2 5 Blinking pattern 3 6 Blinking pattern 4 7 Blinking pattern 5
| ||||
| CfmroFarLedState9 | 1.3.6.1.4.1.1887.1.1.4.3.3.6.1.11 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory State of LED9 of the device. 1 Off 2 On 3 Blinking pattern 1 4 Blinking pattern 2 5 Blinking pattern 3 6 Blinking pattern 4 7 Blinking pattern 5
| ||||
| CfmroFarLedState10 | 1.3.6.1.4.1.1887.1.1.4.3.3.6.1.12 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory State of LED10 of the device. 1 Off 2 On 3 Blinking pattern 1 4 Blinking pattern 2 5 Blinking pattern 3 6 Blinking pattern 4 7 Blinking pattern 5
| ||||
| CfmroFarLedColor1 | 1.3.6.1.4.1.1887.1.1.4.3.3.6.1.13 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Color of LED1 of the device. 1 LED color is black 2 LED color is yellow 3 LED color is red 4 LED color is green
| ||||
| CfmroFarLedColor2 | 1.3.6.1.4.1.1887.1.1.4.3.3.6.1.14 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Color of LED2 of the device. 1 LED color is black 2 LED color is yellow 3 LED color is red 4 LED color is green
| ||||
| CfmroFarLedColor3 | 1.3.6.1.4.1.1887.1.1.4.3.3.6.1.15 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Color of LED3 of the device. 1 LED color is black 2 LED color is yellow 3 LED color is red 4 LED color is green
| ||||
| CfmroFarLedColor4 | 1.3.6.1.4.1.1887.1.1.4.3.3.6.1.16 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Color of LED4 of the device. 1 LED color is black 2 LED color is yellow 3 LED color is red 4 LED color is green
| ||||
| CfmroFarLedColor5 | 1.3.6.1.4.1.1887.1.1.4.3.3.6.1.17 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Color of LED5 of the device. 1 LED color is black 2 LED color is yellow 3 LED color is red 4 LED color is green
| ||||
| CfmroFarLedColor6 | 1.3.6.1.4.1.1887.1.1.4.3.3.6.1.18 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Color of LED6 of the device. 1 LED color is black 2 LED color is yellow 3 LED color is red 4 LED color is green
| ||||
| CfmroFarLedColor7 | 1.3.6.1.4.1.1887.1.1.4.3.3.6.1.19 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Color of LED7 of the device. 1 LED color is black 2 LED color is yellow 3 LED color is red 4 LED color is green
| ||||
| CfmroFarLedColor8 | 1.3.6.1.4.1.1887.1.1.4.3.3.6.1.20 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Color of LED8 of the device. 1 LED color is black 2 LED color is yellow 3 LED color is red 4 LED color is green
| ||||
| CfmroFarLedColor9 | 1.3.6.1.4.1.1887.1.1.4.3.3.6.1.21 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Color of LED9 of the device. 1 LED color is black 2 LED color is yellow 3 LED color is red 4 LED color is green
| ||||
| CfmroFarLedColor10 | 1.3.6.1.4.1.1887.1.1.4.3.3.6.1.22 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Color of LED10 of the device. 1 LED color is black 2 LED color is yellow 3 LED color is red 4 LED color is green
| ||||
| CfmroFarLedState11 | 1.3.6.1.4.1.1887.1.1.4.3.3.6.1.23 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory State of LED11 of the device. 1 Off 2 On 3 Blinking pattern 1 4 Blinking pattern 2 5 Blinking pattern 3 6 Blinking pattern 4 7 Blinking pattern 5
| ||||
| CfmroFarLedState12 | 1.3.6.1.4.1.1887.1.1.4.3.3.6.1.24 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory State of LED12 of the device. 1 Off 2 On 3 Blinking pattern 1 4 Blinking pattern 2 5 Blinking pattern 3 6 Blinking pattern 4 7 Blinking pattern 5
| ||||
| CfmroFarLedState13 | 1.3.6.1.4.1.1887.1.1.4.3.3.6.1.25 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory State of LED13 of the device. 1 Off 2 On 3 Blinking pattern 1 4 Blinking pattern 2 5 Blinking pattern 3 6 Blinking pattern 4 7 Blinking pattern 5
| ||||
| CfmroFarLedState14 | 1.3.6.1.4.1.1887.1.1.4.3.3.6.1.26 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory State of LED14 of the device. 1 Off 2 On 3 Blinking pattern 1 4 Blinking pattern 2 5 Blinking pattern 3 6 Blinking pattern 4 7 Blinking pattern 5
| ||||
| CfmroFarLedState15 | 1.3.6.1.4.1.1887.1.1.4.3.3.6.1.27 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory State of LED15 of the device. 1 Off 2 On 3 Blinking pattern 1 4 Blinking pattern 2 5 Blinking pattern 3 6 Blinking pattern 4 7 Blinking pattern 5
| ||||
| CfmroFarLedState16 | 1.3.6.1.4.1.1887.1.1.4.3.3.6.1.28 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory State of LED16 of the device. 1 Off 2 On 3 Blinking pattern 1 4 Blinking pattern 2 5 Blinking pattern 3 6 Blinking pattern 4 7 Blinking pattern 5
| ||||
| CfmroFarLedState17 | 1.3.6.1.4.1.1887.1.1.4.3.3.6.1.29 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory State of LED17 of the device. 1 Off 2 On 3 Blinking pattern 1 4 Blinking pattern 2 5 Blinking pattern 3 6 Blinking pattern 4 7 Blinking pattern 5
| ||||
| CfmroFarLedState18 | 1.3.6.1.4.1.1887.1.1.4.3.3.6.1.30 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory State of LED18 of the device. 1 Off 2 On 3 Blinking pattern 1 4 Blinking pattern 2 5 Blinking pattern 3 6 Blinking pattern 4 7 Blinking pattern 5
| ||||
| CfmroFarLedState19 | 1.3.6.1.4.1.1887.1.1.4.3.3.6.1.31 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory State of LED19 of the device. 1 Off 2 On 3 Blinking pattern 1 4 Blinking pattern 2 5 Blinking pattern 3 6 Blinking pattern 4 7 Blinking pattern 5
| ||||
| CfmroFarLedState20 | 1.3.6.1.4.1.1887.1.1.4.3.3.6.1.32 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory State of LED20 of the device. 1 Off 2 On 3 Blinking pattern 1 4 Blinking pattern 2 5 Blinking pattern 3 6 Blinking pattern 4 7 Blinking pattern 5
| ||||
| CfmroFarLedColor11 | 1.3.6.1.4.1.1887.1.1.4.3.3.6.1.33 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Color of LED11 of the device. 1 LED color is black 2 LED color is yellow 3 LED color is red 4 LED color is green
| ||||
| CfmroFarLedColor12 | 1.3.6.1.4.1.1887.1.1.4.3.3.6.1.34 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Color of LED12 of the device. 1 LED color is black 2 LED color is yellow 3 LED color is red 4 LED color is green
| ||||
| CfmroFarLedColor13 | 1.3.6.1.4.1.1887.1.1.4.3.3.6.1.35 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Color of LED13 of the device. 1 LED color is black 2 LED color is yellow 3 LED color is red 4 LED color is green
| ||||
| CfmroFarLedColor14 | 1.3.6.1.4.1.1887.1.1.4.3.3.6.1.36 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Color of LED14 of the device. 1 LED color is black 2 LED color is yellow 3 LED color is red 4 LED color is green
| ||||
| CfmroFarLedColor15 | 1.3.6.1.4.1.1887.1.1.4.3.3.6.1.37 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Color of LED15 of the device. 1 LED color is black 2 LED color is yellow 3 LED color is red 4 LED color is green
| ||||
| CfmroFarLedColor16 | 1.3.6.1.4.1.1887.1.1.4.3.3.6.1.38 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Color of LED16 of the device. 1 LED color is black 2 LED color is yellow 3 LED color is red 4 LED color is green
| ||||
| CfmroFarLedColor17 | 1.3.6.1.4.1.1887.1.1.4.3.3.6.1.39 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Color of LED17 of the device. 1 LED color is black 2 LED color is yellow 3 LED color is red 4 LED color is green
| ||||
| CfmroFarLedColor18 | 1.3.6.1.4.1.1887.1.1.4.3.3.6.1.40 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Color of LED18 of the device. 1 LED color is black 2 LED color is yellow 3 LED color is red 4 LED color is green
| ||||
| CfmroFarLedColor19 | 1.3.6.1.4.1.1887.1.1.4.3.3.6.1.41 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Color of LED19 of the device. 1 LED color is black 2 LED color is yellow 3 LED color is red 4 LED color is green
| ||||
| CfmroFarLedColor20 | 1.3.6.1.4.1.1887.1.1.4.3.3.6.1.42 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Color of LED20 of the device. 1 LED color is black 2 LED color is yellow 3 LED color is red 4 LED color is green
| ||||
| TfmroOmiLedStateTable | 1.3.6.1.4.1.1887.1.1.4.3.3.7 | NA | mandatory | |
| RfmroOmiLedStateEntry | 1.3.6.1.4.1.1887.1.1.4.3.3.7.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CfmroOmiLedStatePortIndex | 1.3.6.1.4.1.1887.1.1.4.3.3.7.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CfmroOmiLedState1 | 1.3.6.1.4.1.1887.1.1.4.3.3.7.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory State of LED1 of the OMI: Urgent Alarm 1 Off 2 On 3 Blinking pattern 1 3 Blinking pattern 2 4 Blinking pattern 3
| ||||
| CfmroOmiLedState2 | 1.3.6.1.4.1.1887.1.1.4.3.3.7.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory State of LED2 of the OMI: Non-Urgent Alarm 1 Off 2 On 3 Blinking pattern 1 3 Blinking pattern 2 4 Blinking pattern 3
| ||||
| CfmroOmiLedState3 | 1.3.6.1.4.1.1887.1.1.4.3.3.7.1.5 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory State of LED3 of the OMI: Acknowledged Alarm 1 Off 2 On 3 Blinking pattern 1 3 Blinking pattern 2 4 Blinking pattern 3
| ||||
| CfmroOmiLedState4 | 1.3.6.1.4.1.1887.1.1.4.3.3.7.1.6 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory State of LED4 of the OMI 1 Off 2 On 3 Blinking pattern 1 3 Blinking pattern 2 4 Blinking pattern 3
| ||||
| CfmroOmiLedState5 | 1.3.6.1.4.1.1887.1.1.4.3.3.7.1.7 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory State of LED5 of the OMI 1 Off 2 On 3 Blinking pattern 1 3 Blinking pattern 2 4 Blinking pattern 3
| ||||
| CfmroOmiLedState6 | 1.3.6.1.4.1.1887.1.1.4.3.3.7.1.8 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory State of LED6 of the OMI 1 Off 2 On 3 Blinking pattern 1 3 Blinking pattern 2 4 Blinking pattern 3
| ||||
| CfmroOmiLedState7 | 1.3.6.1.4.1.1887.1.1.4.3.3.7.1.9 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory State of LED7 of the OMI 1 Off 2 On 3 Blinking pattern 1 3 Blinking pattern 2 4 Blinking pattern 3
| ||||
| CfmroOmiLedState8 | 1.3.6.1.4.1.1887.1.1.4.3.3.7.1.10 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory State of LED8 of the OMI 1 Off 2 On 3 Blinking pattern 1 3 Blinking pattern 2 4 Blinking pattern 3
| ||||
| CfmroOmiLedState9 | 1.3.6.1.4.1.1887.1.1.4.3.3.7.1.11 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory State of LED9 of the OMI 1 Off 2 On 3 Blinking pattern 1 3 Blinking pattern 2 4 Blinking pattern 3
| ||||
| CfmroOmiLedState10 | 1.3.6.1.4.1.1887.1.1.4.3.3.7.1.12 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory State of LED10 of the OMI 1 Off 2 On 3 Blinking pattern 1 3 Blinking pattern 2 4 Blinking pattern 3
| ||||
| CfmroOmiLedState11 | 1.3.6.1.4.1.1887.1.1.4.3.3.7.1.13 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory State of LED11 of the OMI 1 Off 2 On 3 Blinking pattern 1 3 Blinking pattern 2 4 Blinking pattern 3
| ||||
| CfmroOmiLedState12 | 1.3.6.1.4.1.1887.1.1.4.3.3.7.1.14 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory State of LED12 of the OMI 1 Off 2 On 3 Blinking pattern 1 3 Blinking pattern 2 4 Blinking pattern 3
| ||||
| CfmroOmiLedState13 | 1.3.6.1.4.1.1887.1.1.4.3.3.7.1.15 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory State of LED13 of the OMI 1 Off 2 On 3 Blinking pattern 1 3 Blinking pattern 2 4 Blinking pattern 3
| ||||
| CfmroOmiLedState14 | 1.3.6.1.4.1.1887.1.1.4.3.3.7.1.16 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory State of LED14 of the OMI 1 Off 2 On 3 Blinking pattern 1 3 Blinking pattern 2 4 Blinking pattern 3
| ||||
| CfmroOmiLedState15 | 1.3.6.1.4.1.1887.1.1.4.3.3.7.1.17 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory State of LED15 of the OMI 1 Off 2 On 3 Blinking pattern 1 3 Blinking pattern 2 4 Blinking pattern 3
| ||||
| CfmroOmiLedState16 | 1.3.6.1.4.1.1887.1.1.4.3.3.7.1.18 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory State of LED16 of the OMI 1 Off 2 On 3 Blinking pattern 1 3 Blinking pattern 2 4 Blinking pattern 3
| ||||
| CfmroOmiLedColor1 | 1.3.6.1.4.1.1887.1.1.4.3.3.7.1.19 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Color of LED1 of the device. 1 LED color is black 2 LED color is yellow 3 LED color is red 4 LED color is green
| ||||
| CfmroOmiLedColor2 | 1.3.6.1.4.1.1887.1.1.4.3.3.7.1.20 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Color of LED2 of the device. 1 LED color is black 2 LED color is yellow 3 LED color is red 4 LED color is green
| ||||
| CfmroOmiLedColor3 | 1.3.6.1.4.1.1887.1.1.4.3.3.7.1.21 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Color of LED3 of the device. 1 LED color is black 2 LED color is yellow 3 LED color is red 4 LED color is green
| ||||
| CfmroOmiLedColor4 | 1.3.6.1.4.1.1887.1.1.4.3.3.7.1.22 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Color of LED4 of the device. 1 LED color is black 2 LED color is yellow 3 LED color is red 4 LED color is green
| ||||
| CfmroOmiLedColor5 | 1.3.6.1.4.1.1887.1.1.4.3.3.7.1.23 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Color of LED5 of the device. 1 LED color is black 2 LED color is yellow 3 LED color is red 4 LED color is green
| ||||
| CfmroOmiLedColor6 | 1.3.6.1.4.1.1887.1.1.4.3.3.7.1.24 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Color of LED6 of the device. 1 LED color is black 2 LED color is yellow 3 LED color is red 4 LED color is green
| ||||
| CfmroOmiLedColor7 | 1.3.6.1.4.1.1887.1.1.4.3.3.7.1.25 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Color of LED7 of the device. 1 LED color is black 2 LED color is yellow 3 LED color is red 4 LED color is green
| ||||
| CfmroOmiLedColor8 | 1.3.6.1.4.1.1887.1.1.4.3.3.7.1.26 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Color of LED8 of the device. 1 LED color is black 2 LED color is yellow 3 LED color is red 4 LED color is green
| ||||
| CfmroOmiLedColor9 | 1.3.6.1.4.1.1887.1.1.4.3.3.7.1.27 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Color of LED9 of the device. 1 LED color is black 2 LED color is yellow 3 LED color is red 4 LED color is green
| ||||
| CfmroOmiLedColor10 | 1.3.6.1.4.1.1887.1.1.4.3.3.7.1.28 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Color of LED10 of the device. 1 LED color is black 2 LED color is yellow 3 LED color is red 4 LED color is green
| ||||
| CfmroOmiLedColor11 | 1.3.6.1.4.1.1887.1.1.4.3.3.7.1.29 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Color of LED11 of the device. 1 LED color is black 2 LED color is yellow 3 LED color is red 4 LED color is green
| ||||
| CfmroOmiLedColor12 | 1.3.6.1.4.1.1887.1.1.4.3.3.7.1.30 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Color of LED12 of the device. 1 LED color is black 2 LED color is yellow 3 LED color is red 4 LED color is green
| ||||
| CfmroOmiLedColor13 | 1.3.6.1.4.1.1887.1.1.4.3.3.7.1.31 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Color of LED13 of the device. 1 LED color is black 2 LED color is yellow 3 LED color is red 4 LED color is green
| ||||
| CfmroOmiLedColor14 | 1.3.6.1.4.1.1887.1.1.4.3.3.7.1.32 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Color of LED14 of the device. 1 LED color is black 2 LED color is yellow 3 LED color is red 4 LED color is green
| ||||
| CfmroOmiLedColor15 | 1.3.6.1.4.1.1887.1.1.4.3.3.7.1.33 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Color of LED15 of the device. 1 LED color is black 2 LED color is yellow 3 LED color is red 4 LED color is green
| ||||
| CfmroOmiLedColor16 | 1.3.6.1.4.1.1887.1.1.4.3.3.7.1.34 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Color of LED16 of the device. 1 LED color is black 2 LED color is yellow 3 LED color is red 4 LED color is green
| ||||
| TfmroThresholdTable | 1.3.6.1.4.1.1887.1.1.4.3.3.8 | NA | mandatory | |
| RfmroThresholdEntry | 1.3.6.1.4.1.1887.1.1.4.3.3.8.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CfmroThresholdPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.3.8.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CfmroThresholdLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.3.8.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CfmroThresholdCounterIndex | 1.3.6.1.4.1.1887.1.1.4.3.3.8.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the performance counter of a link and is used as index for the other elements in the Table The following values are foreseen: 5 LT Wire pair 1 Direction NT 6 Reg1 Wire pair 1 Direction LT 7 Reg1 Wire pair 1 Direction NT 8 NT Wire pair 1 Direction LT 9 LT Wire pair 2 Direction NT 10 Reg1 Wire pair 2 Direction LT 11 Reg1 Wire pair 2 Direction NT 12 NT Wire pair 2 Direction LT 15 Reg2 Wire pair 1 Direction LT 16 Reg2 Wire pair 1 Direction NT 17 Reg2 Wire pair 2 Direction LT 18 Reg2 Wire pair 2 Direction NT 19 Reg3 Wire pair 1 Direction LT 20 Reg3 Wire pair 1 Direction NT 21 Reg4 Wire pair 1 Direction LT 22 Reg4 Wire pair 1 Direction NT 23 Reg5 Wire pair 1 Direction LT 24 Reg5 Wire pair 1 Direction NT 25 Reg6 Wire pair 1 Direction LT 26 Reg6 Wire pair 1 Direction NT 27 Reg7 Wire pair 1 Direction LT 28 Reg7 Wire pair 1 Direction NT 29 Reg8 Wire pair 1 Direction LT 30 Reg8 Wire pair 1 Direction NT 31 Reg3 Wire pair 2 Direction LT 32 Reg3 Wire pair 2 Direction NT 33 Reg4 Wire pair 2 Direction LT 34 Reg4 Wire pair 2 Direction NT 35 Reg5 Wire pair 2 Direction LT 36 Reg5 Wire pair 2 Direction NT 37 Reg6 Wire pair 2 Direction LT 38 Reg6 Wire pair 2 Direction NT 39 Reg7 Wire pair 2 Direction LT 40 Reg7 Wire pair 2 Direction NT 41 Reg8 Wire pair 2 Direction LT 42 Reg8 Wire pair 2 Direction NT 43 Reg1 Wire pair 3 Direction LT 44 Reg1 Wire pair 3 Direction NT 45 Reg2 Wire pair 3 Direction LT 46 Reg2 Wire pair 3 Direction NT 47 Reg3 Wire pair 3 Direction LT 48 Reg3 Wire pair 3 Direction NT 49 Reg4 Wire pair 3 Direction LT 50 Reg4 Wire pair 3 Direction NT 51 Reg5 Wire pair 3 Direction LT 52 Reg5 Wire pair 3 Direction NT 53 Reg6 Wire pair 3 Direction LT 54 Reg6 Wire pair 3 Direction NT 55 Reg7 Wire pair 3 Direction LT 56 Reg7 Wire pair 3 Direction NT 57 Reg8 Wire pair 3 Direction LT 58 Reg8 Wire pair 3 Direction NT 59 Reg1 Wire pair 4 Direction LT 60 Reg1 Wire pair 4 Direction NT 61 Reg2 Wire pair 4 Direction LT 62 Reg2 Wire pair 4 Direction NT 63 Reg3 Wire pair 4 Direction LT 64 Reg3 Wire pair 4 Direction NT 65 Reg4 Wire pair 4 Direction LT 66 Reg4 Wire pair 4 Direction NT 67 Reg5 Wire pair 4 Direction LT 68 Reg5 Wire pair 4 Direction NT 69 Reg6 Wire pair 4 Direction LT 70 Reg6 Wire pair 4 Direction NT 71 Reg7 Wire pair 4 Direction LT 72 Reg7 Wire pair 4 Direction NT 73 Reg8 Wire pair 4 Direction LT 74 Reg8 Wire pair 4 Direction NT 75 LT Wire pair 3 Direction NT 76 NT Wire pair 3 Direction LT 77 LT Wire pair 4 Direction NT 78 NT Wire pair 4 Direction LT | ||||
| CfmroThresholdAlarms | 1.3.6.1.4.1.1887.1.1.4.3.3.8.1.4 | OCTET STRING (SIZE (2)) | RO | mandatory |
column · OCTET STRING (SIZE (2)) · read-only · mandatory Indicates whether the Attenuation and SNR Threshold at this point has been reached or crossed Byte 0 1 None No Attenuation Threshold Alarm 10 Att_Alarm Attenuation Threshold Alarm present 254 Unknown value 255 Unsupported variable for addressed device Byte 1 1 None No SNR Threshold Alarm 10 Snr_Alarm SNR Threshold Alarm present 254 Unknown value 255 Unsupported variable for addressed device | ||||
| TfmroAlarmLogTable | 1.3.6.1.4.1.1887.1.1.4.3.3.9 | NA | mandatory | |
| RfmroAlarmLogEntry | 1.3.6.1.4.1.1887.1.1.4.3.3.9.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CfmroAlarmLogPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.3.9.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CfmroAlarmLogLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.3.9.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CfmroAlarmLogBlockIndex | 1.3.6.1.4.1.1887.1.1.4.3.3.9.1.3 | INTEGER (1..4) | RO | mandatory |
column · INTEGER (1..4) · read-only · mandatory This variable addresses the alarm log block number of a link and is used as index for the other elements in the Table Foreseen values are: 1 Alarm Log Entries 1..25 2 Alarm Log Entries 26..50 3 Alarm Log Entries 51..75 4 Alarm Log Entries 76..100 | ||||
| CfmroAlarmLogLatestDataFieldNumber | 1.3.6.1.4.1.1887.1.1.4.3.3.9.1.4 | INTEGER (1..100) | RO | mandatory |
column · INTEGER (1..100) · read-only · mandatory This variable addresses the latest alarm log entry 254 Unknown value 255 Unsupported variable for addressed device | ||||
| CfmroAlarmLogCurrentTime | 1.3.6.1.4.1.1887.1.1.4.3.3.9.1.5 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable contains the current time in seconds since power up 0xfffffffe Unknown value 0xffffffff Unsupported variable for addressed device | ||||
| CfmroAlarmLogInformation | 1.3.6.1.4.1.1887.1.1.4.3.3.9.1.6 | OCTET STRING (SIZE (176)) | RO | mandatory |
column · OCTET STRING (SIZE (176)) · read-only · mandatory Contains the alarm log entries in blocks of 25 entries where each entry is 7 bytes long. Each entry has the following format: Byte(s) Range Content 1..4 Event time in seconds since power up 5 0..21 Interface at which the event occurred 6 0..18 Error which occurred at the interface 7 Event Details The interfaces are coded as follows: 0 U1 Transmission Interface Wire pair 1 1 U2 Transmission Interface Wire pair 2 2 U Transmission Interface 3 T G.703 Interface 4 DC Data Interface Direction Customer 5 DN Data Interface Direction Network 6 Equipment 7 LOSD 8 T4OUT Loss of Signal for clock output 9 T3IN Loss of Signal for clock input 10 RPS Remote Power Supply 11 RTA 12 Powerfail 13 14 REG1UL Regenerator on wire pair 1, direction LT 15 REG2UL Regenerator on wire pair 2, direction LT 16 REG1UN Regenerator on wire pair 1, direction NT 17 REG2UN Regenerator on wire pair 2, direction NT 18 REG1E Regenerator on wire pair 1 19 REG2E Regenerator on wire pair 2 20 LASER Laser ageing on OTU 21 Powerfail CPE 22 THRES_ATT Attenuation Threshold Alarm 23 THRES_ATT_REG_U1L Attenuation Threshold Alarm at the Regenerator on wire pair 1, direction LT 24 THRES_ATT_REG_U2L Attenuation Threshold Alarm at the Regenerator on wire pair 2, direction LT 25 THRES_ATT_REG_U1N Attenuation Threshold Alarm at the Regenerator on wire pair 1, direction NT 26 THRES_ATT_REG_U2N Attenuation Threshold Alarm at the Regenerator on wire pair 2, direction NT 27 THRES_SNR SNR Threshold Alarm 28 THRES_SNR_REG_U1L SNR Threshold Alarm at the Regenerator on wire pair 1, direction LT 29 THRES_SNR_REG_U2L SNR Threshold Alarm at the Regenerator on wire pair 2, direction LT 30 THRES_SNR_REG_U1N SNR Threshold Alarm at the Regenerator on wire pair 1, direction NT 31 THRES_SNR_REG_U2N SNR Threshold Alarm at the Regenerator on wire pair 2, direction NT 32 U3 Transmission Interface Wire pair 3 33 U4 Transmission Interface Wire pair 4 34 RPS2 Remote Power Supply on wire pair 2 35 RPS3 Remote Power Supply on wire pair 3 36 RPS4 Remote Power Supply on wire pair 4 37 REG3UL Regenerator on wire pair 3, direction LT 38 REG4UL Regenerator on wire pair 4, direction LT 39 REG3UN Regenerator on wire pair 3, direction NT 40 REG4UN Regenerator on wire pair 4, direction NT 41 REG3E Regenerator on wire pair 3 42 REG4E Regenerator on wire pair 4 43 THRES_ATT1 Attenuation Threshold Alarm on wire pair 1 44 THRES_ATT2 Attenuation Threshold Alarm on wire pair 2 45 THRES_ATT3 Attenuation Threshold Alarm on wire pair 3 46 THRES_ATT4 Attenuation Threshold Alarm on wire pair 4 47 THRES_ATT_REG_U3L Attenuation Threshold Alarm at the Regenerator on wire pair 3, direction LT 48 THRES_ATT_REG_U4L Attenuation Threshold Alarm at the Regenerator on wire pair 4, direction LT 49 THRES_ATT_REG_U3N Attenuation Threshold Alarm at the Regenerator on wire pair 3, direction NT 50 THRES_ATT_REG_U4N Attenuation Threshold Alarm at the Regenerator on wire pair 4, direction NT 51 THRES_SNR1 SNR Threshold Alarm on wire pair 1 52 THRES_SNR2 SNR Threshold Alarm on wire pair 2 53 THRES_SNR3 SNR Threshold Alarm on wire pair 3 54 THRES_SNR4 SNR Threshold Alarm on wire pair 4 55 THRES_SNR_REG_U3L SNR Threshold Alarm at the Regenerator on wire pair 3, direction LT 56 THRES_SNR_REG_U4L SNR Threshold Alarm at the Regenerator on wire pair 4, direction LT 57 THRES_SNR_REG_U3N SNR Threshold Alarm at the Regenerator on wire pair 3, direction NT 58 THRES_SNR_REG_U4N SNR Threshold Alarm at the Regenerator on wire pair 4, direction NT 59 V_SL V-Interface on the slave device 60 T_SL T-Interface on the slave device 61 DC_SL Data Interface Direction Customer on the slave device 62 DN_SL Data Interface Direction Network on the slave device 63 VA VA Interface 64 VB VB Interface 65 VC VC Interface 66 VD VD Interface 67 MCSa MCS channel a 68 MCSb MCS channel b 69 MCSc MCS channel c 70 MCSd MCS channel d 71 MCSa_FarEnd MCS channel a, far end 72 MCSb_FarEnd MCS channel b, far end 73 MCSc_FarEnd MCS channel c, far end 74 MCSd_FarEnd MCS channel d, far end 75 MCS MCS 76 WAN_RX WAN Rx 77 WAN_TX WAN Tx 78 ETH_P1 Ethernet Port 1 79 ETH_P2 Ethernet Port 2 80 ETH_P3 Ethernet Port 3 81 ETH_P4 Ethernet Port 4 82 EXT_AL_1 External Alarm 1 83 EXT_AL_2 External Alarm 2 84 EXT_AL_3 External Alarm 3 The Errors which can occur are coded as follows: 0 NONE No alarm 1 HPO Half partial operation 2 FPO Full partial operation 3 BER6 Bit error ratio 10^-6 4 BER3 Bit error ratio 10^-3 5 LOA Loss of activity 6 AIS Alarm indication signal 7 LFA Loss of frame alignment 8 LOS Loss of signal 9 AON Alarm 10 RAI Remote alarm indication 11 UCR12 Undercurrent on wire pair 1 & 2 12 UCR1 Undercurrent on wire pair 1 13 UCR2 Undercurrent on wire pair 2 14 OVR Overload 15 NOSYM Asymmetry 16 DEFECT 17 BNA Bandwidth not available 18 LOSW Loss of Synchronisation The Event Details are bit coded as follows: Bit Value Content 0..1 0 Non-Urgent Alarm 1 Urgent Alarm 2 No Alarm 3 No Alarm 2 4 - 3 8 LT/NT Alaem (clear) / Reg Alarm (set) 4..6 If Bit 3 is set 000 Regenerator Section 1 001 Regenerator Section 2 010 Regenerator Section 3 011 Regenerator Section 4 100 Regenerator Section 5 101 Regenerator Section 6 110 Regenerator Section 7 111 Regenerator Section 8 7 If Bit 3 is clear 128 LT (clear) / NT (set) Byte 176 contains a value specifying the validity of the result of a read operation: 1 Ok Values returned are valid 254 unknown values 255 unsupported variable for addressed device | ||||
| TfmroSruTable | 1.3.6.1.4.1.1887.1.1.4.3.3.10 | NA | mandatory | |
| RfmroSruEntry | 1.3.6.1.4.1.1887.1.1.4.3.3.10.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CfmroSruPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.3.10.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CfmroSruLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.3.10.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CfmroSruSectionIndex | 1.3.6.1.4.1.1887.1.1.4.3.3.10.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Defines which Section of Regenerators is to be queried. Ulaf+ Version 1.0 only supports the first section. 1 section1 First section 2 section2 Second section 3 section3 Third section 4 section4 Fourth section 5 section5 Fifth section 6 section6 Sixth section 7 section7 Seventh section 8 section8 Eighth section
| ||||
| CfmroSruU1L | 1.3.6.1.4.1.1887.1.1.4.3.3.10.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Regenerator Error on SHDSL Path 1 to LT 1 None No Alarm 4 BER6 Bit Error Ratio 10^-6 5 BER3 Bit Error Ratio 10^-3 9 LOS Loss of Signal 19 LOSW Loss of SHDSL synchronistation 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroSruU2L | 1.3.6.1.4.1.1887.1.1.4.3.3.10.1.5 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Regenerator Error on SHDSL Path 2 to LT 1 None No Alarm 4 BER6 Bit Error Ratio 10^-6 5 BER3 Bit Error Ratio 10^-3 9 LOS Loss of Signal 19 LOSW Loss of SHDSL synchronistation 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroSruU1N | 1.3.6.1.4.1.1887.1.1.4.3.3.10.1.6 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Regenerator Error on SHDSL Path 1 to NT 1 None No Alarm 4 BER6 Bit Error Ratio 10^-6 5 BER3 Bit Error Ratio 10^-3 9 LOS Loss of Signal 19 LOSW Loss of SHDSL synchronistation 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroSruU2N | 1.3.6.1.4.1.1887.1.1.4.3.3.10.1.7 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Regenerator Error on SHDSL Path 2 to NT 1 None No Alarm 4 BER6 Bit Error Ratio 10^-6 5 BER3 Bit Error Ratio 10^-3 9 LOS Loss of Signal 19 LOSW Loss of SHDSL synchronistation 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroSruEquipment1 | 1.3.6.1.4.1.1887.1.1.4.3.3.10.1.8 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Equipment Alarm in Regenerator in SHDSL Path 1 1 None No Alarm 10 Alarm Equipment Alarm present 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroSruEquipment2 | 1.3.6.1.4.1.1887.1.1.4.3.3.10.1.9 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Equipment Alarm in Regenerator in SHDSL Path 2 1 None No Alarm 10 Alarm Equipment Alarm present 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroSruU3L | 1.3.6.1.4.1.1887.1.1.4.3.3.10.1.10 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Regenerator Error on xDSL Path 3 to LT 1 None No Alarm 4 BER6 Bit Error Ratio 10^-6 5 BER3 Bit Error Ratio 10^-3 9 LOS Loss of Signal 19 LOSW Loss of SDSL synchronistation 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroSruU4L | 1.3.6.1.4.1.1887.1.1.4.3.3.10.1.11 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Regenerator Error on xDSL Path 4 to LT 1 None No Alarm 4 BER6 Bit Error Ratio 10^-6 5 BER3 Bit Error Ratio 10^-3 9 LOS Loss of Signal 19 LOSW Loss of SDSL synchronistation 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroSruU3N | 1.3.6.1.4.1.1887.1.1.4.3.3.10.1.12 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Regenerator Error on xDSL Path 3 to NT 1 None No Alarm 4 BER6 Bit Error Ratio 10^-6 5 BER3 Bit Error Ratio 10^-3 9 LOS Loss of Signal 19 LOSW Loss of SDSL synchronistation 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroSruU4N | 1.3.6.1.4.1.1887.1.1.4.3.3.10.1.13 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Regenerator Error on xDSL Path 4 to NT 1 None No Alarm 4 BER6 Bit Error Ratio 10^-6 5 BER3 Bit Error Ratio 10^-3 9 LOS Loss of Signal 19 LOSW Loss of SDSL synchronistation 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroSruEquipment3 | 1.3.6.1.4.1.1887.1.1.4.3.3.10.1.14 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Equipment Alarm in Regenerator in xDSL Path 3 1 None No Alarm 10 Alarm Equipment Alarm present 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroSruEquipment4 | 1.3.6.1.4.1.1887.1.1.4.3.3.10.1.15 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Equipment Alarm in Regenerator in xDSL Path 4 1 None No Alarm 10 Alarm Equipment Alarm present 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| TfmroCesPwTable | 1.3.6.1.4.1.1887.1.1.4.3.3.11 | NA | mandatory | |
| RfmroCesPwEntry | 1.3.6.1.4.1.1887.1.1.4.3.3.11.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CfmroCesPwPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.3.11.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CfmroCesPwLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.3.11.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the sub-rack and is used as index for the other elements in the Table | ||||
| CfmroCesPwIndex | 1.3.6.1.4.1.1887.1.1.4.3.3.11.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the pseudo wire | ||||
| CfmroCesPwTdm | 1.3.6.1.4.1.1887.1.1.4.3.3.11.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Alarm on TDM interface of given pseudo wire: 1 None No Alarm 7 AIS Alarm Indication Signal 9 LOS Loss of Signal 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmroCesPwEth | 1.3.6.1.4.1.1887.1.1.4.3.3.11.1.5 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Alarm on Ethernet interface of given pseudo wire: 1 None No Alarm 7 AIS Alarm Indication Signal 11 RAI Remote Alarm Indication 33 ARE Address Resolution Error (no MAC address resolved) 34 LOF Loss of Frames 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| TfmroCesTable | 1.3.6.1.4.1.1887.1.1.4.3.3.12 | NA | mandatory | |
| RfmroCesEntry | 1.3.6.1.4.1.1887.1.1.4.3.3.12.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CfmroCesPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.3.12.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CfmroCesLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.3.12.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the sub-rack and is used as index for the other elements in the Table | ||||
| CfmroCesClockIn | 1.3.6.1.4.1.1887.1.1.4.3.3.12.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Alarm on the CES clock in interface: 1 None No Alarm 9 LOS Loss of Signal 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| Nfmrw | 1.3.6.1.4.1.1887.1.1.4.3.4 | |||
| NfmrwLoop | 1.3.6.1.4.1.1887.1.1.4.3.4.1 | |||
| TfmrwLoopLocalTable | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1 | NA | mandatory | |
| RfmrwLoopLocalEntry | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CfmrwLoopLocalPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CfmrwLoopLocalLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CfmrwLoopLocalLoop3a | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.3 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Loop 3a. The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 3 8 TMN_LOCAL Loop command by local management Bit 4 16 DIP Loop command by local switch Bit 7 128 Sa6-Bit Loop command by Sa6-bit Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bits 2-7 show which sources have issued the loop command. If at least one of them is active, the device will try to set the loop. For some modes of operation or with certain combinations of modules some loop sources might not be available. When setting a loop, the following applies: Bit 3 8 TMN_LOCAL Sets/Clears the Loop on the LT or the NT Local | ||||
| CfmrwLoopLocalLoop2b | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.4 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Loop 2b. The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 3 8 TMN_LOCAL Loop command by local management Bit 4 16 DIP Loop command by local switch Bit 5 32 L140 Loop command by control line 140 Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bits 2-7 show which sources have issued the loop command. If at least one of them is active, the device will try to set the loop. For some modes of operation or with certain combinations of modules some loop sources might not be available. When setting a loop, the following applies: Bit 3 8 TMN_LOCAL Sets the Loop on the LT or the NT Local | ||||
| CfmrwLoopLocalLoop3c | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.5 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Loop 3c. The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 3 8 TMN_LOCAL Loop command by local management Bit 4 16 DIP Loop command by local switch Bit 6 64 L141 Loop command by control line 141 Bit 7 128 Sa6-Bit Loop command by Sa6-bit Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bits 2-7 show which sources have issued the loop command. If at least one of them is active, the device will try to set the loop. For some modes of operation or with certain combinations of modules some loop sources might not be available. When setting a loop, the following applies: Bit 3 8 TMN_LOCAL Sets the Loop on the LT or the NT Local | ||||
| CfmrwLoopLocalLoopReg1A | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.6 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Regenerator Loop in wire pair 1 (first section). The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bit 1 shows whether the loop command has been issued by the management system. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop on the Regenerator | ||||
| CfmrwLoopLocalLoopReg2A | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.7 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Regenerator Loop in wire pair 2 (first section). The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bit 1 shows whether the loop command has been issued by the management system. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop on the Regenerator | ||||
| CfmrwLoopLocalLoopReg1B | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.8 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Regenerator Loop in wire pair 1 (second section). The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bit 1 shows whether the loop command has been issued by the management system. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop on the Regenerator | ||||
| CfmrwLoopLocalLoopReg2B | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.9 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Regenerator Loop in wire pair 2 (second section). The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bit 1 shows whether the loop command has been issued by the management system. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop on the Regenerator | ||||
| CfmrwLoopLocalLoop2Reg1A | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.10 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Regenerator Loop 2 in wire pair 1 (first section). The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bit 1 shows whether the loop command has been issued by the management system. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop on the Regenerator | ||||
| CfmrwLoopLocalLoop2Reg2A | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.11 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Regenerator Loop 2 in wire pair 2 (first section). The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bit 1 shows whether the loop command has been issued by the management system. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop on the Regenerator | ||||
| CfmrwLoopLocalLoop2Reg1B | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.12 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Regenerator Loop 2 in wire pair 1 (second section). The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bit 1 shows whether the loop command has been issued by the management system. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop on the Regenerator | ||||
| CfmrwLoopLocalLoop2Reg2B | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.13 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Regenerator Loop 2 in wire pair 2 (second section). The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bit 1 shows whether the loop command has been issued by the management system. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop on the Regenerator | ||||
| CfmrwLoopLocalLoopReg31 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.14 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Regenerator Loop 2 in wire pair 1 (third section). The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bit 1 shows whether the loop command has been issued by the management system. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop on the Regenerator | ||||
| CfmrwLoopLocalLoopReg32 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.15 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Regenerator Loop 2 in wire pair 2 (third section). The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bit 1 shows whether the loop command has been issued by the management system. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop on the Regenerator | ||||
| CfmrwLoopLocalLoopReg41 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.16 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Regenerator Loop 2 in wire pair 1 (fourth section). The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bit 1 shows whether the loop command has been issued by the management system. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop on the Regenerator | ||||
| CfmrwLoopLocalLoopReg42 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.17 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Regenerator Loop 2 in wire pair 2 (fourth section). The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bit 1 shows whether the loop command has been issued by the management system. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop on the Regenerator | ||||
| CfmrwLoopLocalLoopReg51 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.18 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Regenerator Loop 2 in wire pair 1 (fifth section). The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bit 1 shows whether the loop command has been issued by the management system. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop on the Regenerator | ||||
| CfmrwLoopLocalLoopReg52 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.19 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Regenerator Loop 2 in wire pair 2 (fifth section). The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bit 1 shows whether the loop command has been issued by the management system. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop on the Regenerator | ||||
| CfmrwLoopLocalLoopReg61 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.20 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Regenerator Loop 2 in wire pair 1 (sixth section). The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bit 1 shows whether the loop command has been issued by the management system. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop on the Regenerator | ||||
| CfmrwLoopLocalLoopReg62 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.21 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Regenerator Loop 2 in wire pair 2 (sixth section). The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bit 1 shows whether the loop command has been issued by the management system. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop on the Regenerator | ||||
| CfmrwLoopLocalLoopReg71 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.22 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Regenerator Loop 2 in wire pair 1 (seventh section). The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bit 1 shows whether the loop command has been issued by the management system. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop on the Regenerator | ||||
| CfmrwLoopLocalLoopReg72 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.23 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Regenerator Loop 2 in wire pair 2 (seventh section). The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bit 1 shows whether the loop command has been issued by the management system. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop on the Regenerator | ||||
| CfmrwLoopLocalLoopReg81 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.24 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Regenerator Loop 2 in wire pair 1 (eighth section). The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bit 1 shows whether the loop command has been issued by the management system. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop on the Regenerator | ||||
| CfmrwLoopLocalLoopReg82 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.25 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Regenerator Loop 2 in wire pair 2 (eighth section). The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bit 1 shows whether the loop command has been issued by the management system. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop on the Regenerator | ||||
| CfmrwLoopLocalLoop2Reg31 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.26 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Regenerator Loop 2 in wire pair 1 (third section). The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bit 1 shows whether the loop command has been issued by the management system. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop on the Regenerator | ||||
| CfmrwLoopLocalLoop2Reg32 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.27 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Regenerator Loop 2 in wire pair 2 (third section). The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bit 1 shows whether the loop command has been issued by the management system. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop on the Regenerator | ||||
| CfmrwLoopLocalLoop2Reg41 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.28 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Regenerator Loop 2 in wire pair 1 (fourth section). The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bit 1 shows whether the loop command has been issued by the management system. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop on the Regenerator | ||||
| CfmrwLoopLocalLoop2Reg42 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.29 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Regenerator Loop 2 in wire pair 2 (fourth section). The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bit 1 shows whether the loop command has been issued by the management system. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop on the Regenerator | ||||
| CfmrwLoopLocalLoop2Reg51 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.30 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Regenerator Loop 2 in wire pair 1 (fifth section). The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bit 1 shows whether the loop command has been issued by the management system. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop on the Regenerator | ||||
| CfmrwLoopLocalLoop2Reg52 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.31 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Regenerator Loop 2 in wire pair 2 (fifth section). The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bit 1 shows whether the loop command has been issued by the management system. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop on the Regenerator | ||||
| CfmrwLoopLocalLoop2Reg61 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.32 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Regenerator Loop 2 in wire pair 1 (sixth section). The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bit 1 shows whether the loop command has been issued by the management system. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop on the Regenerator | ||||
| CfmrwLoopLocalLoop2Reg62 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.33 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Regenerator Loop 2 in wire pair 2 (sixth section). The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bit 1 shows whether the loop command has been issued by the management system. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop on the Regenerator | ||||
| CfmrwLoopLocalLoop2Reg71 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.34 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Regenerator Loop 2 in wire pair 1 (seventh section). The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bit 1 shows whether the loop command has been issued by the management system. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop on the Regenerator | ||||
| CfmrwLoopLocalLoop2Reg72 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.35 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Regenerator Loop 2 in wire pair 2 (seventh section). The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bit 1 shows whether the loop command has been issued by the management system. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop on the Regenerator | ||||
| CfmrwLoopLocalLoop2Reg81 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.36 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Regenerator Loop 2 in wire pair 1 (eigtht section). The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bit 1 shows whether the loop command has been issued by the management system. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop on the Regenerator | ||||
| CfmrwLoopLocalLoop2Reg82 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.37 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Regenerator Loop 2 in wire pair 2 (eighth section). The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bit 1 shows whether the loop command has been issued by the management system. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop on the Regenerator | ||||
| CfmrwLoopLocalLoopReg13 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.38 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Regenerator Loop in wire pair 3 (first section). The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bit 1 shows whether the loop command has been issued by the management system. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop on the Regenerator | ||||
| CfmrwLoopLocalLoopReg14 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.39 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Regenerator Loop in wire pair 4 (first section). The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bit 1 shows whether the loop command has been issued by the management system. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop on the Regenerator | ||||
| CfmrwLoopLocalLoopReg23 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.40 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Regenerator Loop in wire pair 3 (second section). The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bit 1 shows whether the loop command has been issued by the management system. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop on the Regenerator | ||||
| CfmrwLoopLocalLoopReg24 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.41 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Regenerator Loop in wire pair 4 (second section). The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bit 1 shows whether the loop command has been issued by the management system. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop on the Regenerator | ||||
| CfmrwLoopLocalLoopReg33 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.42 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Regenerator Loop in wire pair 3 (third section). The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bit 1 shows whether the loop command has been issued by the management system. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop on the Regenerator | ||||
| CfmrwLoopLocalLoopReg34 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.43 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Regenerator Loop in wire pair 4 (third section). The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bit 1 shows whether the loop command has been issued by the management system. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop on the Regenerator | ||||
| CfmrwLoopLocalLoopReg43 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.44 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Regenerator Loop in wire pair 3 (fourth section). The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bit 1 shows whether the loop command has been issued by the management system. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop on the Regenerator | ||||
| CfmrwLoopLocalLoopReg44 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.45 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Regenerator Loop in wire pair 4 (fourth section). The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bit 1 shows whether the loop command has been issued by the management system. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop on the Regenerator | ||||
| CfmrwLoopLocalLoopReg53 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.46 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Regenerator Loop in wire pair 3 (fifth section). The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bit 1 shows whether the loop command has been issued by the management system. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop on the Regenerator | ||||
| CfmrwLoopLocalLoopReg54 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.47 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Regenerator Loop in wire pair 4 (fifth section). The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bit 1 shows whether the loop command has been issued by the management system. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop on the Regenerator | ||||
| CfmrwLoopLocalLoopReg63 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.48 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Regenerator Loop in wire pair 3 (sixth section). The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bit 1 shows whether the loop command has been issued by the management system. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop on the Regenerator | ||||
| CfmrwLoopLocalLoopReg64 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.49 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Regenerator Loop in wire pair 4 (sixth section). The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bit 1 shows whether the loop command has been issued by the management system. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop on the Regenerator | ||||
| CfmrwLoopLocalLoopReg73 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.50 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Regenerator Loop in wire pair 3 (seventh section). The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bit 1 shows whether the loop command has been issued by the management system. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop on the Regenerator | ||||
| CfmrwLoopLocalLoopReg74 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.51 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Regenerator Loop in wire pair 4 (seventh section). The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bit 1 shows whether the loop command has been issued by the management system. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop on the Regenerator | ||||
| CfmrwLoopLocalLoopReg83 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.52 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Regenerator Loop in wire pair 3 (eighth section). The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bit 1 shows whether the loop command has been issued by the management system. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop on the Regenerator | ||||
| CfmrwLoopLocalLoopReg84 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.53 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Regenerator Loop in wire pair 4 (eighth section). The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bit 1 shows whether the loop command has been issued by the management system. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop on the Regenerator | ||||
| CfmrwLoopLocalLoop2Reg13 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.54 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Regenerator Loop 2 in wire pair 3 (first section). The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bit 1 shows whether the loop command has been issued by the management system. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop on the Regenerator | ||||
| CfmrwLoopLocalLoop2Reg14 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.55 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Regenerator Loop 2 in wire pair 4 (first section). The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bit 1 shows whether the loop command has been issued by the management system. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop on the Regenerator | ||||
| CfmrwLoopLocalLoop2Reg23 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.56 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Regenerator Loop 2 in wire pair 3 (second section). The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bit 1 shows whether the loop command has been issued by the management system. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop on the Regenerator | ||||
| CfmrwLoopLocalLoop2Reg24 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.57 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Regenerator Loop 2 in wire pair 4 (second section). The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bit 1 shows whether the loop command has been issued by the management system. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop on the Regenerator | ||||
| CfmrwLoopLocalLoop2Reg33 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.58 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Regenerator Loop 2 in wire pair 3 (third section). The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bit 1 shows whether the loop command has been issued by the management system. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop on the Regenerator | ||||
| CfmrwLoopLocalLoop2Reg34 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.59 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Regenerator Loop 2 in wire pair 4 (third section). The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bit 1 shows whether the loop command has been issued by the management system. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop on the Regenerator | ||||
| CfmrwLoopLocalLoop2Reg43 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.60 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Regenerator Loop 2 in wire pair 3 (fourth section). The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bit 1 shows whether the loop command has been issued by the management system. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop on the Regenerator | ||||
| CfmrwLoopLocalLoop2Reg44 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.61 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Regenerator Loop 2 in wire pair 4 (fourth section). The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bit 1 shows whether the loop command has been issued by the management system. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop on the Regenerator | ||||
| CfmrwLoopLocalLoop2Reg53 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.62 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Regenerator Loop 2 in wire pair 3 (fifth section). The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bit 1 shows whether the loop command has been issued by the management system. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop on the Regenerator | ||||
| CfmrwLoopLocalLoop2Reg54 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.63 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Regenerator Loop 2 in wire pair 4 (fifth section). The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bit 1 shows whether the loop command has been issued by the management system. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop on the Regenerator | ||||
| CfmrwLoopLocalLoop2Reg63 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.64 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Regenerator Loop 2 in wire pair 3 (sixth section). The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bit 1 shows whether the loop command has been issued by the management system. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop on the Regenerator | ||||
| CfmrwLoopLocalLoop2Reg64 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.65 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Regenerator Loop 2 in wire pair 4 (sixth section). The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bit 1 shows whether the loop command has been issued by the management system. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop on the Regenerator | ||||
| CfmrwLoopLocalLoop2Reg73 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.66 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Regenerator Loop 2 in wire pair 3 (seventh section). The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bit 1 shows whether the loop command has been issued by the management system. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop on the Regenerator | ||||
| CfmrwLoopLocalLoop2Reg74 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.67 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Regenerator Loop 2 in wire pair 4 (seventh section). The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bit 1 shows whether the loop command has been issued by the management system. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop on the Regenerator | ||||
| CfmrwLoopLocalLoop2Reg83 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.68 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Regenerator Loop 2 in wire pair 3 (eigtht section). The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bit 1 shows whether the loop command has been issued by the management system. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop on the Regenerator | ||||
| CfmrwLoopLocalLoop2Reg84 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.69 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Regenerator Loop 2 in wire pair 4 (eighth section). The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bit 1 shows whether the loop command has been issued by the management system. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop on the Regenerator | ||||
| CfmrwLoopLocalLoop3a2 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.70 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Loop 3a2. The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 3 8 TMN_LOCAL Loop command by local management Bit 4 16 DIP Loop command by local switch Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bits 2-7 show which sources have issued the loop command. If at least one of them is active, the device will try to set the loop. For some modes of operation or with certain combinations of modules some loop sources might not be available. When setting a loop, the following applies: Bit 3 8 TMN_LOCAL Sets/Clears the Loop on the LT or the NT Local | ||||
| CfmrwLoopLocalLoop3a3 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.71 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Loop 3a3. The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 3 8 TMN_LOCAL Loop command by local management Bit 4 16 DIP Loop command by local switch Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bits 2-7 show which sources have issued the loop command. If at least one of them is active, the device will try to set the loop. For some modes of operation or with certain combinations of modules some loop sources might not be available. When setting a loop, the following applies: Bit 3 8 TMN_LOCAL Sets/Clears the Loop on the LT or the NT Local | ||||
| CfmrwLoopLocalLoop3a4 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.72 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Loop 3a4. The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 3 8 TMN_LOCAL Loop command by local management Bit 4 16 DIP Loop command by local switch Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bits 2-7 show which sources have issued the loop command. If at least one of them is active, the device will try to set the loop. For some modes of operation or with certain combinations of modules some loop sources might not be available. When setting a loop, the following applies: Bit 3 8 TMN_LOCAL Sets/Clears the Loop on the LT or the NT Local | ||||
| CfmrwLoopLocalLoop2b2 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.73 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Loop 2b2. The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 3 8 TMN_LOCAL Loop command by local management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bits 2-7 show which sources have issued the loop command. If at least one of them is active, the device will try to set the loop. For some modes of operation or with certain combinations of modules some loop sources might not be available. When setting a loop, the following applies: Bit 3 8 TMN_LOCAL Sets the Loop on the LT or the NT Local | ||||
| CfmrwLoopLocalLoop2b3 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.74 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Loop 2b3. The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 3 8 TMN_LOCAL Loop command by local management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bits 2-7 show which sources have issued the loop command. If at least one of them is active, the device will try to set the loop. For some modes of operation or with certain combinations of modules some loop sources might not be available. When setting a loop, the following applies: Bit 3 8 TMN_LOCAL Sets the Loop on the LT or the NT Local | ||||
| CfmrwLoopLocalLoop2b4 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.75 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Loop 2b4. The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 3 8 TMN_LOCAL Loop command by local management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bits 2-7 show which sources have issued the loop command. If at least one of them is active, the device will try to set the loop. For some modes of operation or with certain combinations of modules some loop sources might not be available. When setting a loop, the following applies: Bit 3 8 TMN_LOCAL Sets the Loop on the LT or the NT Local | ||||
| CfmrwLoopLocalLoopMcs | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.76 | INTEGER (0..2047) | RW | mandatory |
column · INTEGER (0..2047) · read-write · mandatory State of MCS Loop. The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 3 8 TMN_LOCAL Loop command by local management Bit 8 256 unknown value (ignore other bits) Bit 9 512 unsupported variable for addressed device (ignore other bits) Bit 10 1024 MCS Loop command by MCS The STATE bit shows whether the loop is currently active or not. Bits 2-7 and 10 show which sources have issued the loop command. If at least one of them is active, the device will try to set the loop. For some modes of operation or with certain combinations of modules some loop sources might not be available. When setting a loop, the following applies: Bit 3 8 TMN_LOCAL Sets the Loop on the LT or the NT Local | ||||
| CfmrwLoopLocalLoop2bData | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.77 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Loop 2bData. The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 3 8 TMN_LOCAL Loop command by local management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bits 2-7 show which sources have issued the loop command. If at least one of them is active, the device will try to set the loop. For some modes of operation or with certain combinations of modules some loop sources might not be available. When setting a loop, the following applies: Bit 3 8 TMN_LOCAL Sets the Loop on the LT or the NT Local | ||||
| CfmrwLoopLocalLoop2bEth | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.78 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Loop 2bEth. The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 3 8 TMN_LOCAL Loop command by local management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bits 2-7 show which sources have issued the loop command. If at least one of them is active, the device will try to set the loop. For some modes of operation or with certain combinations of modules some loop sources might not be available. When setting a loop, the following applies: Bit 3 8 TMN_LOCAL Sets the Loop on the LT or the NT Local | ||||
| CfmrwLoopLocalLoop2bDataFar | 1.3.6.1.4.1.1887.1.1.4.3.4.1.1.1.79 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Loop 2bDataFar. The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 3 8 TMN_LOCAL Loop command by local management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bits 2-7 show which sources have issued the loop command. If at least one of them is active, the device will try to set the loop. For some modes of operation or with certain combinations of modules some loop sources might not be available. When setting a loop, the following applies: Bit 3 8 TMN_LOCAL Sets the Loop on the LT or the NT Local | ||||
| TfmrwLoopFarTable | 1.3.6.1.4.1.1887.1.1.4.3.4.1.2 | NA | mandatory | |
| RfmrwLoopFarEntry | 1.3.6.1.4.1.1887.1.1.4.3.4.1.2.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CfmrwLoopFarPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.4.1.2.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CfmrwLoopFarLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.4.1.2.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CfmrwLoopFarLoop3a | 1.3.6.1.4.1.1887.1.1.4.3.4.1.2.1.3 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Loop 3a. The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 3 8 TMN_LOCAL Loop command by local management Bit 4 16 DIP Loop command by local switch Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bits 2-7 show which sources have issued the loop command. If at least one of them is active, the device will try to set the loop. For some modes of operation or with certain combinations of modules some loop sources might not be available. When setting a loop, the following applies: Bit 1 4 EOC_TMN Sets the Loop on the NT Bit 3 8 TMN_LOCAL Sets the Loop on the LT or the NT Local | ||||
| CfmrwLoopFarLoop2b | 1.3.6.1.4.1.1887.1.1.4.3.4.1.2.1.4 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Loop 2b. The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 2 4 EOC_DIP Loop command via EOC by switch Bit 3 8 TMN_LOCAL Loop command by local management Bit 4 16 DIP Loop command by local switch Bit 5 32 L140 Loop command by control line 140 Bit 7 128 Sa6-Bit Loop command by Sa6-bit Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bits 2-7 show which sources have issued the loop command. If at least one of them is active, the device will try to set the loop. For some modes of operation or with certain combinations of modules some loop sources might not be available. When setting a loop, the following applies: Bit 1 4 EOC_TMN Sets the Loop on the NT Bit 3 8 TMN_LOCAL Sets the Loop on the LT or the NT Local | ||||
| CfmrwLoopFarLoop3c | 1.3.6.1.4.1.1887.1.1.4.3.4.1.2.1.5 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Loop 3c. The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 3 8 TMN_LOCAL Loop command by local management Bit 4 16 DIP Loop command by local switch Bit 6 64 L141 Loop command by control line 141 Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bits 2-7 show which sources have issued the loop command. If at least one of them is active, the device will try to set the loop. For some modes of operation or with certain combinations of modules some loop sources might not be available. When setting a loop, the following applies: Bit 1 4 EOC_TMN Sets the Loop on the NT Bit 3 8 TMN_LOCAL Sets the Loop on the LT or the NT Local | ||||
| CfmrwLoopFarLoop2bSlave | 1.3.6.1.4.1.1887.1.1.4.3.4.1.2.1.6 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Loop 2b on the slave device. The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 3 8 TMN_LOCAL Loop command via EOC by management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bits 2-7 show which sources have issued the loop command. If at least one of them is active, the device will try to set the loop. For some modes of operation or with certain combinations of modules some loop sources might not be available. When setting a loop, the following applies: Bit 1 2 EOC_TMN Sets the Loop 2b on the slave device | ||||
| CfmrwLoopFarLoop2b2 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.2.1.7 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Loop 2b2. The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 3 8 TMN_LOCAL Loop command by local management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bits 2-7 show which sources have issued the loop command. If at least one of them is active, the device will try to set the loop. For some modes of operation or with certain combinations of modules some loop sources might not be available. When setting a loop, the following applies: Bit 1 4 EOC_TMN Sets the Loop on the NT Bit 3 8 TMN_LOCAL Sets the Loop on the LT or the NT Local | ||||
| CfmrwLoopFarLoop2b3 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.2.1.8 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Loop 2b3. The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 3 8 TMN_LOCAL Loop command by local management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bits 2-7 show which sources have issued the loop command. If at least one of them is active, the device will try to set the loop. For some modes of operation or with certain combinations of modules some loop sources might not be available. When setting a loop, the following applies: Bit 1 4 EOC_TMN Sets the Loop on the NT Bit 3 8 TMN_LOCAL Sets the Loop on the LT or the NT Local | ||||
| CfmrwLoopFarLoop2b4 | 1.3.6.1.4.1.1887.1.1.4.3.4.1.2.1.9 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Loop 2b4. The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 3 8 TMN_LOCAL Loop command by local management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bits 2-7 show which sources have issued the loop command. If at least one of them is active, the device will try to set the loop. For some modes of operation or with certain combinations of modules some loop sources might not be available. When setting a loop, the following applies: Bit 1 4 EOC_TMN Sets the Loop on the NT Bit 3 8 TMN_LOCAL Sets the Loop on the LT or the NT Local | ||||
| CfmrwLoopFarLoopMcs | 1.3.6.1.4.1.1887.1.1.4.3.4.1.2.1.19 | INTEGER (0..2047) | RW | mandatory |
column · INTEGER (0..2047) · read-write · mandatory State of MCS Loop. The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 2 4 EOC_DIP Loop command via EOC by switch Bit 3 8 TMN_LOCAL Loop command by local management Bit 4 16 DIP Loop command by local switch Bit 8 256 unknown value (ignore other bits) Bit 9 512 unsupported variable for addressed device (ignore other bits) Bit 10 1024 MCS Loop command by MCS The STATE bit shows whether the loop is currently active or not. Bits 2-7 and 10 show which sources have issued the loop command. If at least one of them is active, the device will try to set the loop. For some modes of operation or with certain combinations of modules some loop sources might not be available. When setting a loop, the following applies: Bit 1 4 EOC_TMN Sets the Loop on the NT Bit 3 8 TMN_LOCAL Sets the Loop on the LT or the NT Local | ||||
| CfmrwLoopFarLoop2bData | 1.3.6.1.4.1.1887.1.1.4.3.4.1.2.1.20 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Loop 2bData. The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 3 8 TMN_LOCAL Loop command by local management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bits 2-7 show which sources have issued the loop command. If at least one of them is active, the device will try to set the loop. For some modes of operation or with certain combinations of modules some loop sources might not be available. When setting a loop, the following applies: Bit 1 4 EOC_TMN Sets the Loop on the NT Bit 3 8 TMN_LOCAL Sets the Loop on the LT or the NT Local | ||||
| CfmrwLoopFarLoop2bEth | 1.3.6.1.4.1.1887.1.1.4.3.4.1.2.1.21 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Loop 2bEth. The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 3 8 TMN_LOCAL Loop command by local management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bits 2-7 show which sources have issued the loop command. If at least one of them is active, the device will try to set the loop. For some modes of operation or with certain combinations of modules some loop sources might not be available. When setting a loop, the following applies: Bit 1 4 EOC_TMN Sets the Loop on the NT Bit 3 8 TMN_LOCAL Sets the Loop on the LT or the NT Local | ||||
| CfmrwLoopFarLoop2bDataFar | 1.3.6.1.4.1.1887.1.1.4.3.4.1.2.1.22 | INTEGER (0..1023) | RW | mandatory |
column · INTEGER (0..1023) · read-write · mandatory State of Loop 2bDataFar. The readable value is bit coded as follows: Bit 0 1 STATE physical loop state Bit 1 2 EOC_TMN Loop command via EOC by management Bit 3 8 TMN_LOCAL Loop command by local management Bit 8 256 unknown value (ignore bits 0-7) Bit 9 512 unsupported variable for addressed device (ignore bits 0-7) The STATE bit shows whether the loop is currently active or not. Bits 2-7 show which sources have issued the loop command. If at least one of them is active, the device will try to set the loop. For some modes of operation or with certain combinations of modules some loop sources might not be available. When setting a loop, the following applies: Bit 1 4 EOC_TMN Sets the Loop on the NT Bit 3 8 TMN_LOCAL Sets the Loop on the LT or the NT Local | ||||
| TfmrwLoopConfigTable | 1.3.6.1.4.1.1887.1.1.4.3.4.1.3 | NA | mandatory | |
| RfmrwLoopConfigEntry | 1.3.6.1.4.1.1887.1.1.4.3.4.1.3.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CfmrwLoopConfigPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.4.1.3.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CfmrwLoopConfigLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.4.1.3.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CfmrwLoopConfigAllowRbertLoop | 1.3.6.1.4.1.1887.1.1.4.3.4.1.3.1.3 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Specifies whether a remote MCS-equipped unit is allowd to activate an MCS loop on this line or not. 1 Not Allowed MCS loop activation by management only 2 Allowed MCS loop activation by MCS bit pattern allowed 254 unknown value 255 unsupported variable for addressed device
| ||||
| CfmrwLoopConfigTransparentLoops | 1.3.6.1.4.1.1887.1.1.4.3.4.1.3.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Specifies whether the loops are configured transparent or not. 1 Non Transparent The loops are configured as non transparent 2 Transparent The loops are configured as transparent 254 unknown value 255 unsupported variable for addressed device
| ||||
| NfmrwMask | 1.3.6.1.4.1.1887.1.1.4.3.4.2 | |||
| TfmrwHtuLtMaskTable | 1.3.6.1.4.1.1887.1.1.4.3.4.2.1 | NA | mandatory | |
| RfmrwHtuLtMaskEntry | 1.3.6.1.4.1.1887.1.1.4.3.4.2.1.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CfmrwHtuLtMaskPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.4.2.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CfmrwHtuLtMaskLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.4.2.1.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CfmrwHtuLtMask | 1.3.6.1.4.1.1887.1.1.4.3.4.2.1.1.3 | OCTET STRING (SIZE (9)) | RW | mandatory |
column · OCTET STRING (SIZE (9)) · read-write · mandatory Alarm Severity Mask and Alarm Suppression Mask for LT Alarms. This variable only returns meaningful values if the management system is connected to an LT device. If it is connected to an NT device on the local interface, this variable will return 'NotLt' as result. This variable is an 8 byte octet string. Bytes 0-3 contain the alarm suppression mask, bytes 4-7 contain the severity map. The masks are bit coded. If a bit in the suppression mask is set, the corresponding alarm has the severity defined by the severity mask. If the bit in the suppression mask is zero, the corresponding alarm has no severity (i.e. has no influence on the alarm summary). If a bit in the severity mask is set, the corresponding alarm is considered to be 'Urgent', if it is zero, the alarm is 'Non-Urgent'. The alarms are coded as follows: Suppression Severity Alarm Byte 0 Byte 4 bit 0 bit 0 LOS-U bit 1 bit 1 LFA-U bit 2 bit 2 AIS-U bit 3 bit 3 HPO-U bit 4 bit 4 FPO-U bit 5 bit 5 RAI-U bit 6 bit 6 BER3-U bit 7 bit 7 BER6-U Byte 1 Byte 5 bit 0 bit 0 LOS-U1 bit 1 bit 1 BER3-U1 bit 2 bit 2 BER6-U1 bit 3 bit 3 LOS-U2 bit 4 bit 4 BER3-U2 bit 5 bit 5 BER6-U2 bit 6 bit 6 LOS-T bit 7 bit 7 LFA-T Byte 2 Byte 6 bit 0 bit 0 AIS-T bit 1 bit 1 RAI-T bit 2 bit 2 BER3-T bit 3 bit 3 BER6-T bit 4 bit 4 LOAR-D bit 5 bit 5 LOAT-D bit 6 bit 6 Equipment bit 7 bit 7 A-LOS Byte 3 Byte 7 bit 0 bit 0 LOS-T3 bit 1 bit 1 A-RTA bit 2 bit 2 Powerfail bit 3 bit 3 unused bit 4 bit 4 unused bit 5 bit 5 unused bit 6 bit 6 unused bit 7 bit 7 unused Byte 8 contains a value specifying the validity of the result of a read operation: 1 Ok Values returned are valid 2 NotLt The local device is not an LT 254 unknown values 255 unsupported variable for addressed device | ||||
| CfmrwStuLtMask | 1.3.6.1.4.1.1887.1.1.4.3.4.2.1.1.4 | OCTET STRING (SIZE (11)) | RW | mandatory |
column · OCTET STRING (SIZE (11)) · read-write · mandatory Alarm Severity Mask and Alarm Suppression Mask for LT Alarms. This variable only returns meaningful values if the management system is connected to an LT device. If it is connected to an NT device on the local interface, this variable will return 'NotLt' as result. This variable is an 10 byte octet string. Bytes 0-4 contain the alarm suppression mask, bytes 5-9 contain the severity map. The masks are bit coded. If a bit in the suppression mask is set, the corresponding alarm has the severity defined by the severity mask. If the bit in the suppression mask is zero, the corresponding alarm has no severity (i.e. has no influence on the alarm summary). If a bit in the severity mask is set, the corresponding alarm is considered to be 'Urgent', if it is zero, the alarm is 'Non-Urgent'. The alarms are coded as follows: Suppression Severity Alarm Byte 0 Byte 5 bit 0 bit 0 LOS-U bit 1 bit 1 LFA-U bit 2 bit 2 AIS-U bit 3 bit 3 HPO-U bit 4 bit 4 FPO-U bit 5 bit 5 RAI-U bit 6 bit 6 BER3-U bit 7 bit 7 BER6-U Byte 1 Byte 6 bit 0 bit 0 LOS-U1 bit 1 bit 1 BER3-U1 bit 2 bit 2 BER6-U1 bit 3 bit 3 LOS-U2 bit 4 bit 4 BER3-U2 bit 5 bit 5 BER6-U2 bit 6 bit 6 LOS-T bit 7 bit 7 LFA-T Byte 2 Byte 7 bit 0 bit 0 AIS-T bit 1 bit 1 RAI-T bit 2 bit 2 BER3-T bit 3 bit 3 BER6-T bit 4 bit 4 LOAR-D bit 5 bit 5 LOAT-D bit 6 bit 6 Equipment bit 7 bit 7 A-LOS Byte 3 Byte 8 bit 0 bit 0 LOS-T3 bit 1 bit 1 A-RTA bit 2 bit 2 Powerfail bit 3 bit 3 U-Bandwidth unavailable bit 4 bit 4 LOSW-U1 bit 5 bit 5 LOSW-U2 bit 6 bit 6 Powerfail CPE bit 7 bit 7 TD-ATT-U1 Byte 4 Byte 9 bit 0 bit 0 TD-SNR-U1 bit 1 bit 1 TD-ATT-U2 bit 2 bit 2 TD-SNR-U2 bit 3 bit 3 reserved bit 4 bit 4 reserved bit 5 bit 5 XFW bit 6 bit 6 unused bit 7 bit 7 unused Byte 10 contains a value specifying the validity of the result of a read operation: 1 Ok Values returned are valid 2 NotLt The local device is not an LT 254 unknown values 255 unsupported variable for addressed device | ||||
| CfmrwStu4LtMask | 1.3.6.1.4.1.1887.1.1.4.3.4.2.1.1.5 | OCTET STRING (SIZE (9)) | RW | mandatory |
column · OCTET STRING (SIZE (9)) · read-write · mandatory Alarm Severity Mask and Alarm Suppression Mask for LT Alarms. This variable only returns meaningful values if the management system is connected to an LT device. If it is connected to an NT device on the local interface, this variable will return 'NotLt' as result. This variable is an 8 byte octet string. Bytes 0-3 contain the alarm suppression mask, bytes 4-7 contain the severity map. The masks are bit coded. If a bit in the suppression mask is set, the corresponding alarm has the severity defined by the severity mask. If the bit in the suppression mask is zero, the corresponding alarm has no severity (i.e. has no influence on the alarm summary). If a bit in the severity mask is set, the corresponding alarm is considered to be 'Urgent', if it is zero, the alarm is 'Non-Urgent'. The alarms are coded as follows: Suppression Severity Alarm Byte 0 Byte 4 bit 0 bit 0 LOS-U1 bit 1 bit 1 BER3-U1 bit 2 bit 2 BER6-U1 bit 3 bit 3 LOSW-U1 bit 4 bit 4 LOS-V_A bit 5 bit 5 LFA-V_A bit 6 bit 6 AIS-V_A bit 7 bit 7 RAI-V_A Byte 1 Byte 5 bit 0 bit 0 BER3-V_A bit 1 bit 1 BER6-V_A bit 2 bit 2 LOAR-WAN bit 3 bit 3 LOAT-WAN bit 4 bit 4 MIR-WAN bit 5 bit 5 LINKDOWN-P1 bit 6 bit 6 Equipment bit 7 bit 7 A-LOS Byte 2 Byte 6 bit 0 bit 0 Powerfail CPE bit 1 bit 1 TD-ATT-U1 bit 2 bit 2 TD-SNR-U1 bit 3 bit 3 LOM-MCSx bit 4 bit 4 BER3-MCSx bit 5 bit 5 BER6-MCSx bit 6 bit 6 LOM-FARMCSx bit 7 bit 7 LOM Byte 3 Byte 7 bit 0 bit 0 PLOM bit 1 bit 1 LOS-T3 bit 2 bit 2 Powerfail bit 3 bit 3 XFW bit 4 bit 4 bit 5 bit 5 bit 6 bit 6 bit 7 bit 7 Byte 8 contains a value specifying the validity of the result of a read operation: 1 Ok Values returned are valid 2 NotLt The local device is not an LT 254 unknown values 255 unsupported variable for addressed device | ||||
| TfmrwHtuNtMaskTable | 1.3.6.1.4.1.1887.1.1.4.3.4.2.2 | NA | mandatory | |
| RfmrwHtuNtMaskEntry | 1.3.6.1.4.1.1887.1.1.4.3.4.2.2.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CfmrwHtuNtMaskPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.4.2.2.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CfmrwHtuNtMaskLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.4.2.2.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CfmrwHtuNtMask | 1.3.6.1.4.1.1887.1.1.4.3.4.2.2.1.3 | OCTET STRING (SIZE (9)) | RW | mandatory |
column · OCTET STRING (SIZE (9)) · read-write · mandatory Alarm Severity Mask and Alarm Suppression Mask for NT Alarms. This variable is an 8 byte octet string. Bytes 0-3 contain the alarm suppression mask, bytes 4-7 contain the severity map. The masks are bit coded. If a bit in the suppression mask is set, the corresponding alarm has the severity defined by the severity mask. If the bit in the suppression mask is zero, the corresponding alarm has no severity (i.e. has no influence on the alarm summary). If a bit in the severity mask is set, the corresponding alarm is considered to be 'Urgent', if it is zero, the alarm is 'Non-Urgent'. The alarms are coded as follows: Suppression Severity Alarm Byte 0 Byte 4 bit 0 bit 0 LOS-U bit 1 bit 1 LFA-U bit 2 bit 2 AIS-U bit 3 bit 3 HPO-U bit 4 bit 4 FPO-U bit 5 bit 5 RAI-U bit 6 bit 6 BER3-U bit 7 bit 7 BER6-U Byte 1 Byte 5 bit 0 bit 0 LOS-U1 bit 1 bit 1 BER3-U1 bit 2 bit 2 BER6-U1 bit 3 bit 3 LOS-U2 bit 4 bit 4 BER3-U2 bit 5 bit 5 BER6-U2 bit 6 bit 6 LOS-T bit 7 bit 7 LFA-T Byte 2 Byte 6 bit 0 bit 0 AIS-T bit 1 bit 1 RAI-T bit 2 bit 2 BER3-T bit 3 bit 3 BER6-T bit 4 bit 4 LOAR-D bit 5 bit 5 LOAT-D bit 6 bit 6 Equipment bit 7 bit 7 A-LOS Byte 3 Byte 7 bit 0 bit 0 LOS-T4 bit 1 bit 1 unused bit 2 bit 2 unused bit 3 bit 3 unused bit 4 bit 4 unused bit 5 bit 5 unused bit 6 bit 6 unused bit 7 bit 7 unused Byte 8 contains a value specifying the validity of the result of a read operation: 1 Ok Values returned are valid 254 unknown values 255 unsupported variable for addressed device | ||||
| CfmrwStuNtMask | 1.3.6.1.4.1.1887.1.1.4.3.4.2.2.1.4 | OCTET STRING (SIZE (11)) | RW | mandatory |
column · OCTET STRING (SIZE (11)) · read-write · mandatory Alarm Severity Mask and Alarm Suppression Mask for NT Alarms. This variable is an 10 byte octet string. Bytes 0-4 contain the alarm suppression mask, bytes 5-9 contain the severity map. The masks are bit coded. If a bit in the suppression mask is set, the corresponding alarm has the severity defined by the severity mask. If the bit in the suppression mask is zero, the corresponding alarm has no severity (i.e. has no influence on the alarm summary). If a bit in the severity mask is set, the corresponding alarm is considered to be 'Urgent', if it is zero, the alarm is 'Non-Urgent'. The alarms are coded as follows: Suppression Severity Alarm Byte 0 Byte 5 bit 0 bit 0 LOS-U bit 1 bit 1 LFA-U bit 2 bit 2 AIS-U bit 3 bit 3 HPO-U bit 4 bit 4 FPO-U bit 5 bit 5 RAI-U bit 6 bit 6 BER3-U bit 7 bit 7 BER6-U Byte 1 Byte 6 bit 0 bit 0 LOS-U1 bit 1 bit 1 BER3-U1 bit 2 bit 2 BER6-U1 bit 3 bit 3 LOS-U2 bit 4 bit 4 BER3-U2 bit 5 bit 5 BER6-U2 bit 6 bit 6 LOS-T bit 7 bit 7 LFA-T Byte 2 Byte 7 bit 0 bit 0 AIS-T bit 1 bit 1 RAI-T bit 2 bit 2 BER3-T bit 3 bit 3 BER6-T bit 4 bit 4 LOAR-D bit 5 bit 5 LOAT-D bit 6 bit 6 Equipment bit 7 bit 7 A-LOS Byte 3 Byte 8 bit 0 bit 0 LOS-T4 bit 1 bit 1 U-Bandwidth unavailable bit 2 bit 2 LOSW-U1 bit 3 bit 3 LOSW-U2 bit 4 bit 4 Powerfail CPE bit 5 bit 5 TD-ATT-U1 bit 6 bit 6 TD-SNR-U1 bit 7 bit 7 TD-ATT-U2 Byte 4 Byte 9 bit 0 bit 0 TD-SNR-U2 bit 1 bit 1 unused bit 2 bit 2 unused bit 3 bit 3 unused bit 4 bit 4 unused bit 5 bit 5 unused bit 6 bit 6 unused bit 7 bit 7 unused Byte 10 contains a value specifying the validity of the result of a read operation: 1 Ok Values returned are valid 254 unknown values 255 unsupported variable for addressed device | ||||
| CfmrwStu4NtMask | 1.3.6.1.4.1.1887.1.1.4.3.4.2.2.1.5 | OCTET STRING (SIZE (9)) | RW | mandatory |
column · OCTET STRING (SIZE (9)) · read-write · mandatory Alarm Severity Mask and Alarm Suppression Mask for NT Alarms. This variable only returns meaningful values if the management system is connected to an LT device. If it is connected to an NT device on the local interface, this variable will return 'NotLt' as result. This variable is an 8 byte octet string. Bytes 0-3 contain the alarm suppression mask, bytes 4-7 contain the severity map. The masks are bit coded. If a bit in the suppression mask is set, the corresponding alarm has the severity defined by the severity mask. If the bit in the suppression mask is zero, the corresponding alarm has no severity (i.e. has no influence on the alarm summary). If a bit in the severity mask is set, the corresponding alarm is considered to be 'Urgent', if it is zero, the alarm is 'Non-Urgent'. The alarms are coded as follows: Suppression Severity Alarm Byte 0 Byte 4 bit 0 bit 0 LOS-U1 bit 1 bit 1 BER3-U1 bit 2 bit 2 BER6-U1 bit 3 bit 3 LOSW-U1 bit 4 bit 4 LOS-V_A bit 5 bit 5 LFA-V_A bit 6 bit 6 AIS-V_A bit 7 bit 7 RAI-V_A Byte 1 Byte 5 bit 0 bit 0 BER3-V_A bit 1 bit 1 BER6-V_A bit 2 bit 2 LOAR-WAN bit 3 bit 3 LOAT-WAN bit 4 bit 4 MIR-WAN bit 5 bit 5 LINKDOWN-P1 bit 6 bit 6 Equipment bit 7 bit 7 A-LOS Byte 2 Byte 6 bit 0 bit 0 TD-ATT-U1 bit 1 bit 1 TD-SNR-U1 bit 2 bit 2 LOM-MCSx bit 3 bit 3 BER3-MCSx bit 4 bit 4 BER6-MCSx bit 5 bit 5 LOM-FARMCSx bit 6 bit 6 LOM bit 7 bit 7 PLOM Byte 3 Byte 7 bit 0 bit 0 Powerfail bit 1 bit 1 bit 2 bit 2 bit 3 bit 3 bit 4 bit 4 bit 5 bit 5 bit 6 bit 6 bit 7 bit 7 Byte 8 contains a value specifying the validity of the result of a read operation: 1 Ok Values returned are valid 254 unknown values 255 unsupported variable for addressed device | ||||
| TfmrwRpsMaskTable | 1.3.6.1.4.1.1887.1.1.4.3.4.2.4 | NA | mandatory | |
| RfmrwRpsMaskEntry | 1.3.6.1.4.1.1887.1.1.4.3.4.2.4.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CfmrwRpsMaskPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.4.2.4.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CfmrwRpsMaskLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.4.2.4.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CfmrwRpsMask | 1.3.6.1.4.1.1887.1.1.4.3.4.2.4.1.3 | OCTET STRING (SIZE (3)) | RW | mandatory |
column · OCTET STRING (SIZE (3)) · read-write · mandatory Alarm Severity Mask and Alarm Suppression Mask for Remote Power Supply (RPS). This variable only returns meaningful values if the management system is connected to an LT device. If it is connected to an NT device on the local interface, this variable will return 'NotLt' as result. This variable is an 2 byte octet string. Byte 0 contains the alarm suppression mask, byte 1 contains the severity map. The masks are bit coded. If a bit in the suppression mask is set, the corresponding alarm has the severity defined by the severity mask. If the bit in the suppression mask is zero, the corresponding alarm has no severity (i.e. has no influence on the alarm summary). If a bit in the severity mask is set, the corresponding alarm is considered to be 'Urgent', if it is zero, the alarm is 'Non-Urgent'. The alarms are coded as follows: Suppression Severity Alarm Byte 0 Byte 1 bit 0 bit 0 UCR12 bit 1 bit 1 UCR1 bit 2 bit 2 UCR2 bit 3 bit 3 OVR bit 4 bit 4 NOSYM bit 5 bit 5 DEFECT bit 6 bit 6 unused bit 7 bit 7 unused Byte 2 contains a value specifying the validity of the result of a read operation: 1 Ok Values returned are valid 2 NotLt The local device is not an LT 254 unknown values 255 unsupported variable for addressed device | ||||
| TfmrwRegAMaskTable | 1.3.6.1.4.1.1887.1.1.4.3.4.2.5 | NA | mandatory | |
| RfmrwRegAMaskEntry | 1.3.6.1.4.1.1887.1.1.4.3.4.2.5.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CfmrwRegAMaskPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.4.2.5.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CfmrwRegAMaskLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.4.2.5.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CfmrwRegAMask | 1.3.6.1.4.1.1887.1.1.4.3.4.2.5.1.3 | OCTET STRING (SIZE (5)) | RW | mandatory |
column · OCTET STRING (SIZE (5)) · read-write · mandatory Alarm Severity Mask and Alarm Suppression Mask for Regenerator Section A (LT side). This variable only returns meaningful values if the management system is connected to an LT device. If it is connected to an NT device on the local interface, this variable will return 'NotLt' as result. This variable is a 4 byte octet string. Bytes 0-1 contain the alarm suppression mask, bytes 2-3 contain the severity map. The masks are bit coded. If a bit in the suppression mask is set, the corresponding alarm has the severity defined by the severity mask. If the bit in the suppression mask is zero, the corresponding alarm has no severity (i.e. has no influence on the alarm summary). If a bit in the severity mask is set, the corresponding alarm is considered to be 'Urgent', if it is zero, the alarm is 'Non-Urgent'. The alarms are coded as follows: Suppression Severity Alarm Byte 0 Byte 2 bit 0 bit 0 LOS-R1L bit 1 bit 1 BER3-R1L bit 2 bit 2 BER6-R1L bit 3 bit 3 LOS-R2L bit 4 bit 4 BER3-R2L bit 5 bit 5 BER6-R2L bit 6 bit 6 LOS-R1N bit 7 bit 7 BER3-R1N Byte 1 Byte 3 bit 0 bit 0 BER6-R1N bit 1 bit 1 LOS-R2N bit 2 bit 2 BER3-R2N bit 3 bit 3 BER6-R2N bit 4 bit 4 Equipment1 bit 5 bit 5 Equipment2 bit 6 bit 6 unused bit 7 bit 7 unused Byte 4 contains a value specifying the validity of the result of a read operation: 1 Ok Values returned are valid 2 NotLt The local device is not an LT 254 unknown values 255 unsupported variable for addressed device | ||||
| TfmrwOmiMaskTable | 1.3.6.1.4.1.1887.1.1.4.3.4.2.7 | NA | mandatory | |
| RfmrwOmiMaskEntry | 1.3.6.1.4.1.1887.1.1.4.3.4.2.7.1 | NA | mandatory | |
row · not-accessible · mandatory
| ||||
| CfmrwOmiMaskPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.4.2.7.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CfmrwOmiMask | 1.3.6.1.4.1.1887.1.1.4.3.4.2.7.1.2 | OCTET STRING (SIZE (3)) | RW | mandatory |
column · OCTET STRING (SIZE (3)) · read-write · mandatory Alarm Severity Mask and Alarm Suppression Mask for the OMI card. This variable is a 2 byte octet string. Byte 0 contains the alarm suppression mask, byte 1 contains the severity map. The masks are bit coded. If a bit in the suppression mask is set, the corresponding alarm has the severity defined by the severity mask. If the bit in the suppression mask is zero, the corresponding alarm has no severity (i.e. has no influence on the alarm summary). If a bit in the severity mask is set, the corresponding alarm is considered to be 'Urgent', if it is zero, the alarm is 'Non-Urgent'. The alarms are coded as follows: Suppression Severity Alarm Byte 0 Byte 1 bit 0 bit 0 BAT1 bit 1 bit 1 BAT2 bit 2 bit 2 AUX BAT MCU bit 3 bit 3 unused bit 4 bit 4 unused bit 5 bit 5 unused bit 6 bit 6 unused bit 7 bit 7 unused Byte 2 contains a value specifying the validity of the result of a read operation: 1 Ok Values returned are valid 254 unknown values 255 unsupported variable for addressed device | ||||
| CfmrwOmiExtInputMask | 1.3.6.1.4.1.1887.1.1.4.3.4.2.7.1.3 | OCTET STRING (SIZE (3)) | RW | mandatory |
column · OCTET STRING (SIZE (3)) · read-write · mandatory External input alarm Severity and Suppression Mask for the MCU card. Byte 0 alarm suppression mask, (bit coded: 0=masked 1= no masked) Byte 1 alarm severity map (bit coded: 0=not urgent, 1=urgent) The masks are bit coded. If a bit in the suppression mask is set, the corresponding alarm has the severity defined by the severity mask. If the bit in the suppression mask is zero, the corresponding alarm has no severity (i.e. has no influence on the alarm summary). If a bit in the severity mask is set, the corresponding alarm is considered to be 'Urgent', if it is zero, the alarm is 'Non-Urgent'. The alarm mask is bit coded as follows: Suppression Severity Alarm Byte 0 Byte 1 bit 0 bit 0 EXTERNAL INPUT 1 bit 1 bit 1 EXTERNAL INPUT 2 bit 2 bit 2 EXTERNAL INPUT 3 bit 3 bit 3 EXTERNAL INPUT 4 bit 4 bit 4 unused bit 5 bit 5 unused bit 6 bit 6 unused bit 7 bit 7 unused Byte 2 contains a value specifying the validity of the result of a read operation: 1 Ok Values returned are valid 254 unknown values 255 unsupported variable for addressed device | ||||
| CfmrwOmiNMSMask | 1.3.6.1.4.1.1887.1.1.4.3.4.2.7.1.4 | OCTET STRING (SIZE (3)) | RW | mandatory |
column · OCTET STRING (SIZE (3)) · read-write · mandatory NMS link alarm Severity and Suppression Mask for the MCU card. Byte 0 alarm suppression mask, (bit coded: 0=masked 1= no masked) Byte 1 alarm severity map (bit coded: 0=not urgent, 1=urgent) The masks are bit coded. If a bit in the suppression mask is set, the corresponding alarm has the severity defined by the severity mask. If the bit in the suppression mask is zero, the corresponding alarm has no severity (i.e. has no influence on the alarm summary). If a bit in the severity mask is set, the corresponding alarm is considered to be 'Urgent', if it is zero, the alarm is 'Non-Urgent'. The alarm mask is bit coded as follows: Suppression Severity Alarm Byte 0 Byte 1 bit 0 bit 0 NMS LINK ALARM bit 1 bit 1 unused bit 2 bit 2 unused bit 3 bit 3 unused bit 4 bit 4 unused bit 5 bit 5 unused bit 6 bit 6 unused bit 7 bit 7 unused Byte 2 contains a value specifying the validity of the result of a read operation: 1 Ok Values returned are valid 254 unknown values 255 unsupported variable for addressed device | ||||
| CfmrwOmiFEMask | 1.3.6.1.4.1.1887.1.1.4.3.4.2.7.1.5 | OCTET STRING (SIZE (3)) | RW | mandatory |
column · OCTET STRING (SIZE (3)) · read-write · mandatory Fast Ethernet link alarm Severity and Suppression Mask for the MCU card. Byte 0 alarm suppression mask, (bit coded: 0=masked 1= no masked) Byte 1 alarm severity map (bit coded: 0=not urgent, 1=urgent) The masks are bit coded. If a bit in the suppression mask is set, the corresponding alarm has the severity defined by the severity mask. If the bit in the suppression mask is zero, the corresponding alarm has no severity (i.e. has no influence on the alarm summary). If a bit in the severity mask is set, the corresponding alarm is considered to be 'Urgent', if it is zero, the alarm is 'Non-Urgent'. The alarm mask is bit coded as follows: Suppression Severity Alarm Byte 0 Byte 1 bit 0 bit 0 FE LINK ALARM bit 1 bit 1 unused bit 2 bit 2 unused bit 3 bit 3 unused bit 4 bit 4 unused bit 5 bit 5 unused bit 6 bit 6 unused bit 7 bit 7 unused Byte 2 contains a value specifying the validity of the result of a read operation: 1 Ok Values returned are valid 254 unknown values 255 unsupported variable for addressed device | ||||
| CfmrwOmiGBEMask | 1.3.6.1.4.1.1887.1.1.4.3.4.2.7.1.6 | OCTET STRING (SIZE (3)) | RW | mandatory |
column · OCTET STRING (SIZE (3)) · read-write · mandatory GigaBit Ethernet link alarm Severity and Suppression Mask for the MCU card. Byte 0 alarm suppression mask, (bit coded: 0=masked 1= no masked) Byte 1 alarm severity map (bit coded: 0=not urgent, 1=urgent) The masks are bit coded. If a bit in the suppression mask is set, the corresponding alarm has the severity defined by the severity mask. If the bit in the suppression mask is zero, the corresponding alarm has no severity (i.e. has no influence on the alarm summary). If a bit in the severity mask is set, the corresponding alarm is considered to be 'Urgent', if it is zero, the alarm is 'Non-Urgent'. The alarm mask is bit coded as follows: Suppression Severity Alarm Byte 0 Byte 1 bit 0 bit 0 GBE LINK ALARM bit 1 bit 1 unused bit 2 bit 2 unused bit 3 bit 3 unused bit 4 bit 4 unused bit 5 bit 5 unused bit 6 bit 6 unused bit 7 bit 7 unused Byte 2 contains a value specifying the validity of the result of a read operation: 1 Ok Values returned are valid 254 unknown values 255 unsupported variable for addressed device | ||||
| CfmrwOmiSFPMask | 1.3.6.1.4.1.1887.1.1.4.3.4.2.7.1.7 | OCTET STRING (SIZE (3)) | RW | mandatory |
column · OCTET STRING (SIZE (3)) · read-write · mandatory SFP laser/interface alarm Severity and Suppression Mask for the MCU card. Byte 0 alarm suppression mask, (bit coded: 0=masked 1= no masked) Byte 1 alarm severity map (bit coded: 0=not urgent, 1=urgent) The masks are bit coded. If a bit in the suppression mask is set, the corresponding alarm has the severity defined by the severity mask. If the bit in the suppression mask is zero, the corresponding alarm has no severity (i.e. has no influence on the alarm summary). If a bit in the severity mask is set, the corresponding alarm is considered to be 'Urgent', if it is zero, the alarm is 'Non-Urgent'. The alarm mask is bit coded as follows: Suppression Severity Alarm Byte 0 Byte 1 bit 0 bit 0 SFP LASER ALARM bit 1 bit 1 SFP INTERFACE ALARM bit 2 bit 2 unused bit 3 bit 3 unused bit 4 bit 4 unused bit 5 bit 5 unused bit 6 bit 6 unused bit 7 bit 7 unused Byte 2 contains a value specifying the validity of the result of a read operation: 1 Ok Values returned are valid 254 unknown values 255 unsupported variable for addressed device | ||||
| CfmrwOmiOutputMask | 1.3.6.1.4.1.1887.1.1.4.3.4.2.7.1.8 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Alarm output mask for the MCU card 1 Alarm output Off 2 Alarm output On 254 unknown value 255 unsupported variable for addressed device
| ||||
| CfmrwOmiCESMask | 1.3.6.1.4.1.1887.1.1.4.3.4.2.7.1.9 | OCTET STRING (SIZE (3)) | RW | mandatory |
column · OCTET STRING (SIZE (3)) · read-write · mandatory CES interface alarm Severity and Suppression Mask for the MCU card. Byte 0 alarm suppression mask, (bit coded: 0=masked 1= no masked) Byte 1 alarm severity map (bit coded: 0=not urgent, 1=urgent) The masks are bit coded. If a bit in the suppression mask is set, the corresponding alarm has the severity defined by the severity mask. If the bit in the suppression mask is zero, the corresponding alarm has no severity (i.e. has no influence on the alarm summary). If a bit in the severity mask is set, the corresponding alarm is considered to be 'Urgent', if it is zero, the alarm is 'Non-Urgent'. The alarm mask is bit coded as follows: Suppression Severity Alarm Byte 0 Byte 1 bit 0 bit 0 LOS TDM bit 1 bit 1 ARE ETH bit 2 bit 2 LOF ETH bit 3 bit 3 LOS Clock In bit 4 bit 4 AIS TDM bit 5 bit 5 RAI ETH bit 6 bit 6 AIS ETH bit 7 bit 7 unused Byte 2 contains a value specifying the validity of the result of a read operation: 1 Ok Values returned are valid 254 unknown values 255 unsupported variable for addressed device | ||||
| TfmrwFarRpsMaskTable | 1.3.6.1.4.1.1887.1.1.4.3.4.2.8 | NA | mandatory | |
| RfmrwFarRpsMaskEntry | 1.3.6.1.4.1.1887.1.1.4.3.4.2.8.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CfmrwFarRpsMaskPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.4.2.8.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CfmrwFarRpsMaskLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.4.2.8.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CfmrwFarRpsMask | 1.3.6.1.4.1.1887.1.1.4.3.4.2.8.1.3 | OCTET STRING (SIZE (3)) | RW | mandatory |
column · OCTET STRING (SIZE (3)) · read-write · mandatory Alarm Severity Mask and Alarm Suppression Mask for Remote Power Supply (RPS). This variable only returns meaningful values if the management system is connected to an LT device. If it is connected to an NT device on the local interface, this variable will return 'NotLt' as result. This variable is an 2 byte octet string. Byte 0 contains the alarm suppression mask, byte 1 contains the severity map. The masks are bit coded. If a bit in the suppression mask is set, the corresponding alarm has the severity defined by the severity mask. If the bit in the suppression mask is zero, the corresponding alarm has no severity (i.e. has no influence on the alarm summary). If a bit in the severity mask is set, the corresponding alarm is considered to be 'Urgent', if it is zero, the alarm is 'Non-Urgent'. The alarms are coded as follows: Suppression Severity Alarm Byte 0 Byte 1 bit 0 bit 0 UCR12 bit 1 bit 1 UCR1 bit 2 bit 2 UCR2 bit 3 bit 3 OVR bit 4 bit 4 NOSYM bit 5 bit 5 DEFECT bit 6 bit 6 unused bit 7 bit 7 unused Byte 2 contains a value specifying the validity of the result of a read operation: 1 Ok Values returned are valid 254 unknown values 255 unsupported variable for addressed device | ||||
| TfmrwSruMaskTable | 1.3.6.1.4.1.1887.1.1.4.3.4.2.9 | NA | mandatory | |
| RfmrwSruMaskEntry | 1.3.6.1.4.1.1887.1.1.4.3.4.2.9.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CfmrwSruMaskPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.4.2.9.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CfmrwSruMaskLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.4.2.9.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CfmrwSruMask | 1.3.6.1.4.1.1887.1.1.4.3.4.2.9.1.3 | OCTET STRING (SIZE (5)) | RW | mandatory |
column · OCTET STRING (SIZE (5)) · read-write · mandatory Alarm Severity Mask and Alarm Suppression Mask for Regenerator Section A (LT side). This variable only returns meaningful values if the management system is connected to an LT device. If it is connected to an NT device on the local interface, this variable will return 'NotLt' as result. This variable is a 4 byte octet string. Bytes 0-1 contain the alarm suppression mask, bytes 2-3 contain the severity map. The masks are bit coded. If a bit in the suppression mask is set, the corresponding alarm has the severity defined by the severity mask. If the bit in the suppression mask is zero, the corresponding alarm has no severity (i.e. has no influence on the alarm summary). If a bit in the severity mask is set, the corresponding alarm is considered to be 'Urgent', if it is zero, the alarm is 'Non-Urgent'. The alarms are coded as follows: Suppression Severity Alarm Byte 0 Byte 2 bit 0 bit 0 LOS-L bit 1 bit 1 BER3-L bit 2 bit 2 BER6-L bit 3 bit 3 LOS-N bit 4 bit 4 BER3-N bit 5 bit 5 BER6-N bit 6 bit 6 Equipment bit 7 bit 7 LOSW-L Byte 1 Byte 3 bit 0 bit 0 LOSW-N bit 1 bit 1 Thres-Att-L bit 2 bit 2 Thres-Att-N bit 3 bit 3 Thres-Snr-L bit 4 bit 4 Thres-Snr-N bit 5 bit 5 unused bit 6 bit 6 unused bit 7 bit 7 unused Byte 4 contains a value specifying the validity of the result of a read operation: 1 Ok Values returned are valid 2 NotLt The local device is not an LT 254 unknown values 255 unsupported variable for addressed device | ||||
| TfmrwGtuMasterMaskTable | 1.3.6.1.4.1.1887.1.1.4.3.4.2.10 | NA | mandatory | |
| RfmrwGtuMasterMaskEntry | 1.3.6.1.4.1.1887.1.1.4.3.4.2.10.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CfmrwGtuMasterMaskPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.4.2.10.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CfmrwGtuMasterMaskLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.4.2.10.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CfmrwGtuMasterMask | 1.3.6.1.4.1.1887.1.1.4.3.4.2.10.1.3 | OCTET STRING (SIZE (9)) | RW | mandatory |
column · OCTET STRING (SIZE (9)) · read-write · mandatory Alarm Severity Mask and Alarm Suppression Mask for Master Alarms. This variable only returns meaningful values if the management system is connected to an LT device. If it is connected to an NT device on the local interface, this variable will return 'NotLt' as result. This variable is an 8 byte octet string. Bytes 0-3 contain the alarm suppression mask, bytes 4-7 contain the severity map. The masks are bit coded. If a bit in the suppression mask is set, the corresponding alarm has the severity defined by the severity mask. If the bit in the suppression mask is zero, the corresponding alarm has no severity (i.e. has no influence on the alarm summary). If a bit in the severity mask is set, the corresponding alarm is considered to be 'Urgent', if it is zero, the alarm is 'Non-Urgent'. The alarms are coded as follows: Suppression Severity Alarm Byte 0 Byte 4 bit 0 bit 0 LOS-V bit 1 bit 1 LFA-V bit 2 bit 2 AIS-V bit 3 bit 3 RAI-V bit 4 bit 4 BER3-V bit 5 bit 5 BER6-V bit 6 bit 6 LOS-T bit 7 bit 7 LFA-T Byte 1 Byte 5 bit 0 bit 0 AIS-T bit 1 bit 1 RAI-T bit 2 bit 2 BER3-T bit 3 bit 3 BER6-T bit 4 bit 4 LOAR-D bit 5 bit 5 LOAT-D bit 6 bit 6 Equipment bit 7 bit 7 A-LOS Byte 2 Byte 6 bit 0 bit 0 LOS-T4 bit 1 bit 1 LOS-V-Slave bit 2 bit 2 LFA-V-Slave bit 3 bit 3 AIS-V-Slave bit 4 bit 4 RAI-V-Slave bit 5 bit 5 BER3-V-Slave bit 6 bit 6 BER6-V-Slave bit 7 bit 7 LOS-T-Slave Byte 3 Byte 7 bit 0 bit 0 LFA-T-Slave bit 1 bit 1 AIS-T-Slave bit 2 bit 2 RAI-T-Slave bit 3 bit 3 BER3-T-Slave bit 4 bit 4 BER6-T-Slave bit 5 bit 5 LOAR-D-Slave bit 6 bit 6 LOAT-D-Slave bit 7 bit 7 unused Byte 8 contains a value specifying the validity of the result of a read operation: 1 Ok Values returned are valid 2 NotLt The local device is not an LT 254 unknown values 255 unsupported variable for addressed device | ||||
| TfmrwLocalAlarmMaskConfigTable | 1.3.6.1.4.1.1887.1.1.4.3.4.2.11 | NA | mandatory | |
| RfmrwLocalAlarmMaskConfigEntry | 1.3.6.1.4.1.1887.1.1.4.3.4.2.11.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CfmrwLocalAlarmMaskConfigPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.4.2.11.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CfmrwLocalAlarmMaskConfigLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.4.2.11.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CfmrwLocalAlarmMaskConfigArray | 1.3.6.1.4.1.1887.1.1.4.3.4.2.11.1.3 | OCTET STRING (SIZE (91)) | RW | mandatory |
column · OCTET STRING (SIZE (91)) · read-write · mandatory Alarm Severity Mask and Alarm Suppression Mask for LT Alarms. This variable only returns meaningful values if the management system is connected to an LT device. If it is connected to an NT device on the local interface, this variable will return 'NotLt' as result. This variable is an 91 byte octet string. Bytes 0-29 contain the alarm suppression mask, bytes 30-59 contain the severity mask, bytes 60-89 contain the logging mask. The masks are bit coded. If a bit in the suppression mask is set, the corresponding alarm has the severity defined by the severity mask. If the bit in the suppression mask is zero, the corresponding alarm has no severity (i.e. has no influence on the alarm summary). If a bit in the severity mask is set, the corresponding alarm is considered to be 'Urgent', if it is zero, the alarm is 'Non-Urgent'. If the bit in the logging mask is set, the corresponding alarm is logged. Alarm mask coding for STUP/QSTUP: Suppression Severity Logging Alarm Byte 0 Byte 30 Byte 60 bit 0 bit 0 bit 0 XTU_LOS_U bit 1 bit 1 bit 1 XTU_LFA_U bit 2 bit 2 bit 2 XTU_AIS_U bit 3 bit 3 bit 3 XTU_BNA_U bit 4 bit 4 bit 4 XTU_RAI_U bit 5 bit 5 bit 5 XTU_BER3_U bit 6 bit 6 bit 6 XTU_BER6_U bit 7 bit 7 bit 7 XTU_LOS_Ux Byte 1 Byte 31 Byte 61 bit 0 bit 0 bit 0 XTU_LOSW_Ux bit 1 bit 1 bit 1 XTU_BER3_Ux bit 2 bit 2 bit 2 XTU_BER6_Ux bit 3 bit 3 bit 3 XTU_LOS_T bit 4 bit 4 bit 4 XTU_LFA_T bit 5 bit 5 bit 5 XTU_AIS_T bit 6 bit 6 bit 6 XTU_RAI_T bit 7 bit 7 bit 7 XTU_BER3_T Byte 21 Byte 32 Byte 62 bit 0 bit 0 bit 0 XTU_BER6_T bit 1 bit 1 bit 1 XTU_LOA_RX_D bit 2 bit 2 bit 2 XTU_LOA_TX_D bit 3 bit 3 bit 3 XTU_EQUIPMENT bit 4 bit 4 bit 4 XTU_LOS_T3 bit 5 bit 5 bit 5 XTU_LOS_T4 bit 6 bit 6 bit 6 XTU_P1_LINKDOWN bit 7 bit 7 bit 7 XTU_LOA_RX_WAN Byte 3 Byte 33 Byte 63 bit 0 bit 0 bit 0 XTU_LOA_TX_WAN bit 1 bit 1 bit 1 XTU_MIR_TX_WAN bit 2 bit 2 bit 2 XTU_LOS_D bit 3 bit 3 bit 3 XTU_POWERFAIL bit 4 bit 4 bit 4 XTU_REM_PWRFAIL bit 5 bit 5 bit 5 XTU_TD_ATT bit 6 bit 6 bit 6 XTU_TD_SNR bit 7 bit 7 bit 7 XTU_XFW Bytes 4-14 Bytes 34-44 Bytes 64-74 unused Byte 15 Byte 45 Byte 75 bit 0 bit 0 bit 0 XRU_LOS_UL bit 1 bit 1 bit 1 XRU_BER3_UL bit 2 bit 2 bit 2 XRU_BER6_UL bit 3 bit 3 bit 3 XRU_LOS_UN bit 4 bit 4 bit 4 XRU_BER3_UN bit 5 bit 5 bit 5 XRU_BER6_UN bit 6 bit 6 bit 6 XRU_EQUIPMENT bit 7 bit 7 bit 7 XRU_LOSW_UL Byte 16 Byte 46 Byte 76 bit 0 bit 0 bit 0 XRU_LOSW_UN bit 1 bit 1 bit 1 XRU_TD_ATT_UL bit 2 bit 2 bit 2 XRU_TD_SNR_UL bit 3 bit 3 bit 3 XRU_TD_ATT_UN bit 4 bit 4 bit 4 XRU_TD_SNR_UN bit 5 bit 5 bit 5 unused bit 6 bit 6 bit 6 unused bit 7 bit 7 bit 7 unused Bytes 17-24 Bytes 47-54 Bytes 77-84 unused Byte 25 Byte 55 Byte 85 bit 0 bit 0 bit 0 RPS_UC bit 1 bit 1 bit 1 RPS_OC bit 2 bit 2 bit 2 RPS_UNBAL bit 3 bit 3 bit 3 RPS_DEFEKT bit 4 bit 4 bit 4 unused bit 5 bit 5 bit 5 unused bit 6 bit 6 bit 6 unused bit 7 bit 7 bit 7 unused Bytes 26-29 Bytes 56-59 Bytes 86-89 unused Byte 90 contains a value specifying the validity of the result of a read operation: 1 Ok Values returned are valid 254 unknown values 255 unsupported variable for addressed device | ||||
| TfmrwFarAlarmMaskConfigTable | 1.3.6.1.4.1.1887.1.1.4.3.4.2.12 | NA | mandatory | |
| RfmrwFarAlarmMaskConfigEntry | 1.3.6.1.4.1.1887.1.1.4.3.4.2.12.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CfmrwFarAlarmMaskConfigPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.4.2.12.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CfmrwFarAlarmMaskConfigLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.4.2.12.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CfmrwFarAlarmMaskConfigArray | 1.3.6.1.4.1.1887.1.1.4.3.4.2.12.1.3 | OCTET STRING (SIZE (91)) | RW | mandatory |
column · OCTET STRING (SIZE (91)) · read-write · mandatory Alarm Severity Mask and Alarm Suppression Mask for NT Alarms. This variable is an 91 byte octet string. Bytes 0-29 contain the alarm suppression mask, bytes 30-59 contain the severity mask, bytes 60-89 contain the logging mask. The masks are bit coded. If a bit in the suppression mask is set, the corresponding alarm has the severity defined by the severity mask. If the bit in the suppression mask is zero, the corresponding alarm has no severity (i.e. has no influence on the alarm summary). If a bit in the severity mask is set, the corresponding alarm is considered to be 'Urgent', if it is zero, the alarm is 'Non-Urgent'. If the bit in the logging mask is set, the corresponding alarm is logged. Alarm mask coding for STUP/QSTUP: Suppression Severity Logging Alarm Byte 0 Byte 30 Byte 60 bit 0 bit 0 bit 0 XTU_LOS_U bit 1 bit 1 bit 1 XTU_LFA_U bit 2 bit 2 bit 2 XTU_AIS_U bit 3 bit 3 bit 3 XTU_BNA_U bit 4 bit 4 bit 4 XTU_RAI_U bit 5 bit 5 bit 5 XTU_BER3_U bit 6 bit 6 bit 6 XTU_BER6_U bit 7 bit 7 bit 7 XTU_LOS_Ux Byte 1 Byte 31 Byte 61 bit 0 bit 0 bit 0 XTU_LOSW_Ux bit 1 bit 1 bit 1 XTU_BER3_Ux bit 2 bit 2 bit 2 XTU_BER6_Ux bit 3 bit 3 bit 3 XTU_LOS_T bit 4 bit 4 bit 4 XTU_LFA_T bit 5 bit 5 bit 5 XTU_AIS_T bit 6 bit 6 bit 6 XTU_RAI_T bit 7 bit 7 bit 7 XTU_BER3_T Byte 21 Byte 32 Byte 62 bit 0 bit 0 bit 0 XTU_BER6_T bit 1 bit 1 bit 1 XTU_LOA_RX_D bit 2 bit 2 bit 2 XTU_LOA_TX_D bit 3 bit 3 bit 3 XTU_EQUIPMENT bit 4 bit 4 bit 4 XTU_LOS_T3 bit 5 bit 5 bit 5 XTU_LOS_T4 bit 6 bit 6 bit 6 XTU_P1_LINKDOWN bit 7 bit 7 bit 7 XTU_LOA_RX_WAN Byte 3 Byte 33 Byte 63 bit 0 bit 0 bit 0 XTU_LOA_TX_WAN bit 1 bit 1 bit 1 XTU_MIR_TX_WAN bit 2 bit 2 bit 2 XTU_LOS_D bit 3 bit 3 bit 3 XTU_POWERFAIL bit 4 bit 4 bit 4 XTU_REM_PWRFAIL bit 5 bit 5 bit 5 XTU_TD_ATT bit 6 bit 6 bit 6 XTU_TD_SNR bit 7 bit 7 bit 7 XTU_XFW Bytes 4-14 Bytes 34-44 Bytes 64-74 unused Byte 15 Byte 45 Byte 75 bit 0 bit 0 bit 0 XRU_LOS_UL bit 1 bit 1 bit 1 XRU_BER3_UL bit 2 bit 2 bit 2 XRU_BER6_UL bit 3 bit 3 bit 3 XRU_LOS_UN bit 4 bit 4 bit 4 XRU_BER3_UN bit 5 bit 5 bit 5 XRU_BER6_UN bit 6 bit 6 bit 6 XRU_EQUIPMENT bit 7 bit 7 bit 7 XRU_LOSW_UL Byte 16 Byte 46 Byte 76 bit 0 bit 0 bit 0 XRU_LOSW_UN bit 1 bit 1 bit 1 XRU_TD_ATT_UL bit 2 bit 2 bit 2 XRU_TD_SNR_UL bit 3 bit 3 bit 3 XRU_TD_ATT_UN bit 4 bit 4 bit 4 XRU_TD_SNR_UN bit 5 bit 5 bit 5 unused bit 6 bit 6 bit 6 unused bit 7 bit 7 bit 7 unused Bytes 17-24 Bytes 47-54 Bytes 77-84 unused Byte 25 Byte 55 Byte 85 bit 0 bit 0 bit 0 RPS_UC bit 1 bit 1 bit 1 RPS_OC bit 2 bit 2 bit 2 RPS_UNBAL bit 3 bit 3 bit 3 RPS_DEFEKT bit 4 bit 4 bit 4 unused bit 5 bit 5 bit 5 unused bit 6 bit 6 bit 6 unused bit 7 bit 7 bit 7 unused Bytes 26-29 Bytes 56-59 Bytes 86-89 unused Byte 90 contains a value specifying the validity of the result of a read operation: 1 Ok Values returned are valid 254 unknown values 255 unsupported variable for addressed device | ||||
| NfmrwTrap | 1.3.6.1.4.1.1887.1.1.4.3.4.3 | |||
| TfmrwHtuTrapTable | 1.3.6.1.4.1.1887.1.1.4.3.4.3.1 | NA | mandatory | |
| RfmrwHtuTrapEntry | 1.3.6.1.4.1.1887.1.1.4.3.4.3.1.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CfmrwHtuTrapPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.4.3.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CfmrwHtuTrapLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.4.3.1.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CfmrwHtuTrapEnable | 1.3.6.1.4.1.1887.1.1.4.3.4.3.1.1.3 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Allows the suppression of all traps from a certain device without altering the assigned alarm severities via the alarm masks. The following values are supported: 1 Disabled Suppress all traps 2 Enabled Send traps from this system 254 Unknown value (not supported for set) 255 Unsupported variable for addressed device (not supported for set)
| ||||
| CfmrwHtuTrapSuppDisAlarmTrap | 1.3.6.1.4.1.1887.1.1.4.3.4.3.1.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Allows the suppression of alarm traps when the line's overall alarm summary remains 'No Alarm'. This feature is useful for preventing masked alarm from causing unwanted trap traffic. Trap generation can be suppressed entirely using the variable fmrwHtuTrapEnable. The following values are supported: 1 Disabled Allow all traps 2 Enabled Suppress trap for constant 'No Alarm' summary 254 Unknown value (not supported for set) 255 Unsupported variable for addressed device (not supported for set)
| ||||
| TfmrwOmiTrapTable | 1.3.6.1.4.1.1887.1.1.4.3.4.3.2 | NA | mandatory | |
| RfmrwOmiTrapEntry | 1.3.6.1.4.1.1887.1.1.4.3.4.3.2.1 | NA | mandatory | |
row · not-accessible · mandatory
| ||||
| CfmrwOmiTrapPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.4.3.2.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CfmrwOmiTrapEnable | 1.3.6.1.4.1.1887.1.1.4.3.4.3.2.1.2 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Allows the suppression of all traps from a certain OMI without altering the assigned alarm severities via the alarm masks. The following values are supported: 1 Disabled Suppress all traps originating on this OMI 2 Enabled Send traps from this OMI 254 Unknown value (not supported for set) 255 Unsupported variable for addressed device (not supported for set) Please note that the suppression mechanism only suppresses those traps originating on the OMI itself but not traps generated by line cards which are addressed through the OMI. These traps must be suppressed on the line cards themselves.
| ||||
| CfmrwOmiTrapSuppDisAlarmTrap | 1.3.6.1.4.1.1887.1.1.4.3.4.3.2.1.3 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Allows the suppression of alarm traps when the line's overall
alarm summary remains 'No Alarm'. This feature is useful for
preventing masked alarm from causing unwanted trap traffic.
Trap generation can be suppressed entirely using the variable
fmrwOmiTrapEnable.
1 Disabled Suppress all traps originating on this OMI
2 Enabled Send traps from this OMI
254 Unknown value (not supported for set)
255 Unsupported variable for addressed device (not supported for set)
| ||||
| TfmrwThresholdTable | 1.3.6.1.4.1.1887.1.1.4.3.4.4 | NA | mandatory | |
| RfmrwThresholdEntry | 1.3.6.1.4.1.1887.1.1.4.3.4.4.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CfmrwThresholdPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.4.4.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CfmrwThresholdLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.4.4.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CfmrwThresholdAttenuation | 1.3.6.1.4.1.1887.1.1.4.3.4.4.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Defines the Attenuation Threshold 1 disabled Disabled 2 att1dB Attenuation in dB (1..127) ... Attenuation in dB (1..127) 128 att127dB Attenuation in dB (1..127) 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CfmrwThresholdSnr | 1.3.6.1.4.1.1887.1.1.4.3.4.4.1.5 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Defines the Signal To Noise Ration (SNR) Threshold 1 disabled Disabled 2 snr1dB SNR Margin in db (1..15) ... SNR Margin in db (1..15) 16 snr15dB SNR Margin in db (1..15) 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| NfmrwActions | 1.3.6.1.4.1.1887.1.1.4.3.4.5 | |||
| TfmrwHtuActionTable | 1.3.6.1.4.1.1887.1.1.4.3.4.5.1 | NA | mandatory | |
| RfmrwHtuActionEntry | 1.3.6.1.4.1.1887.1.1.4.3.4.5.1.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CfmrwHtuActionPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.4.5.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CfmrwHtuActionLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.4.5.1.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CfmrwHtuActionResetAlarmLog | 1.3.6.1.4.1.1887.1.1.4.3.4.5.1.1.3 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Clears the content of the Alarm Log 1 Reset Clears the log 254 Unknown value (not supported for set) 255 Unsupported variable for addressed device (not supported for set)
| ||||
| NfmrwConfig | 1.3.6.1.4.1.1887.1.1.4.3.4.6 | |||
| TfmrwConfigTable | 1.3.6.1.4.1.1887.1.1.4.3.4.6.1 | NA | mandatory | |
| RfmrwConfigEntry | 1.3.6.1.4.1.1887.1.1.4.3.4.6.1.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CfmrwConfigPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.4.6.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CfmrwConfigLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.4.6.1.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CfmrwLocalPwrFailAlarmSupp | 1.3.6.1.4.1.1887.1.1.4.3.4.6.1.1.3 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Allows the suppression of power failure alarms. In addition to the alarm masking provided by fmrwXtuXtMask, this feature actually suppresses alarm generation at all. 1 Disabled Allow power failure alarms 2 Enabled Suppress power failure alarms 254 Unknown value (not supported for set) 255 Unsupported variable for addressed device (not supported for set)
| ||||
| CfmrwLocalL2SwitchTestMode | 1.3.6.1.4.1.1887.1.1.4.3.4.6.1.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Defines whether the L2Switch operates in test mode
('transparent switch') or in standard mode.
1 Inactive L2Switch operates in standard mode
2 Active L2Switch operates in test mode
254 unknown
255 unsupported
| ||||
| CfmrwFarPwrFailAlarmSupp | 1.3.6.1.4.1.1887.1.1.4.3.4.6.1.1.5 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Allows the suppression of power failure alarms. In addition to the alarm masking provided by fmrwXtuXtMask, this feature actually suppresses alarm generation at all. 1 Disabled Allow power failure alarms 2 Enabled Suppress power failure alarms 254 Unknown value (not supported for set) 255 Unsupported variable for addressed device (not supported for set)
| ||||
| CfmrwFarL2SwitchTestMode | 1.3.6.1.4.1.1887.1.1.4.3.4.6.1.1.6 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Defines whether the L2Switch operates in test mode
('transparent switch') or in standard mode.
1 Inactive L2Switch operates in standard mode
2 Active L2Switch operates in test mode
254 unknown
255 unsupported
| ||||
| Npmro | 1.3.6.1.4.1.1887.1.1.4.3.5 | |||
| TpmroHdslTable | 1.3.6.1.4.1.1887.1.1.4.3.5.1 | NA | mandatory | |
| RpmroHdslEntry | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CpmroHdslPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CpmroHdslLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CpmroHdslAttenuation1 | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.3 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of HDSL Path 1 at the local device 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuation2 | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.4 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of HDSL Path 2 at the local device 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMargin1 | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.5 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of HDSL Path 1 at the local device. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMargin2 | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.6 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of HDSL Path 2 at the local device. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationNt1 | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.7 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationNt2 | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.8 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginNt1 | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.9 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of the line. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginNt2 | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.10 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of the line. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationReg1ALt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.11 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationReg1ANt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.12 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationReg2ALt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.13 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationReg2ANt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.14 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationReg1BLt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.15 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationReg1BNt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.16 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationReg2BLt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.17 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationReg2BNt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.18 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginReg1ALt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.19 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of HDSL Path 1 at the local device. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginReg1ANt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.20 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of HDSL Path 2 at the local device. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginReg2ALt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.21 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of HDSL Path 1 at the local device. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginReg2ANt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.22 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of HDSL Path 2 at the local device. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginReg1BLt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.23 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of HDSL Path 1 at the local device. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginReg1BNt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.24 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of HDSL Path 2 at the local device. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginReg2BLt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.25 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of HDSL Path 1 at the local device. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginReg2BNt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.26 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of HDSL Path 2 at the local device. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationReg31Lt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.27 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationReg31Nt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.28 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationReg32Lt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.29 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationReg32Nt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.30 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationReg41Lt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.31 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationReg41Nt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.32 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationReg42Lt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.33 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationReg42Nt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.34 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationReg51Lt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.35 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationReg51Nt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.36 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationReg52Lt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.37 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationReg52Nt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.38 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationReg61Lt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.39 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationReg61Nt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.40 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationReg62Lt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.41 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationReg62Nt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.42 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationReg71Lt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.43 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationReg71Nt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.44 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationReg72Lt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.45 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationReg72Nt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.46 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationReg81Lt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.47 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationReg81Nt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.48 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationReg82Lt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.49 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationReg82Nt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.50 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginReg31Lt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.51 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of HDSL Path 2 at the local device. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginReg31Nt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.52 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of HDSL Path 2 at the local device. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginReg32Lt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.53 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of HDSL Path 2 at the local device. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginReg32Nt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.54 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of HDSL Path 2 at the local device. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginReg41Lt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.55 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of HDSL Path 2 at the local device. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginReg41Nt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.56 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of HDSL Path 2 at the local device. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginReg42Lt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.57 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of HDSL Path 2 at the local device. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginReg42Nt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.58 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of HDSL Path 2 at the local device. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginReg51Lt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.59 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of HDSL Path 2 at the local device. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginReg51Nt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.60 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of HDSL Path 2 at the local device. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginReg52Lt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.61 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of HDSL Path 2 at the local device. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginReg52Nt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.62 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of HDSL Path 2 at the local device. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginReg61Lt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.63 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of HDSL Path 2 at the local device. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginReg61Nt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.64 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of HDSL Path 2 at the local device. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginReg62Lt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.65 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of HDSL Path 2 at the local device. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginReg62Nt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.66 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of HDSL Path 2 at the local device. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginReg71Lt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.67 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of HDSL Path 2 at the local device. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginReg71Nt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.68 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of HDSL Path 2 at the local device. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginReg72Lt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.69 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of HDSL Path 2 at the local device. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginReg72Nt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.70 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of HDSL Path 2 at the local device. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginReg81Lt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.71 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of HDSL Path 2 at the local device. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginReg81Nt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.72 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of HDSL Path 2 at the local device. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginReg82Lt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.73 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of HDSL Path 2 at the local device. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginReg82Nt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.74 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of HDSL Path 2 at the local device. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslAttenuation3 | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.75 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of HDSL Path 3 at the local device 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuation4 | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.76 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of HDSL Path 4 at the local device 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationNt3 | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.77 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationNt4 | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.78 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationReg13Lt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.79 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationReg13Nt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.80 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationReg14Lt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.81 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationReg14Nt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.82 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationReg23Lt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.83 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationReg23Nt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.84 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationReg24Lt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.85 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationReg24Nt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.86 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationReg33Lt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.87 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationReg33Nt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.88 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationReg34Lt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.89 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationReg34Nt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.90 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationReg43Lt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.91 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationReg43Nt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.92 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationReg44Lt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.93 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationReg44Nt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.94 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationReg53Lt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.95 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationReg53Nt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.96 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationReg54Lt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.97 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationReg54Nt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.98 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationReg63Lt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.99 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationReg63Nt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.100 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationReg64Lt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.101 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationReg64Nt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.102 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationReg73Lt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.103 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationReg73Nt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.104 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationReg74Lt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.105 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationReg74Nt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.106 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationReg83Lt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.107 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationReg83Nt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.108 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationReg84Lt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.109 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslAttenuationReg84Nt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.110 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Attenuation of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMargin3 | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.111 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of HDSL Path 3 at the local device. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMargin4 | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.112 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of HDSL Path 4 at the local device. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginNt3 | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.113 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of the line. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginNt4 | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.114 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of the line. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginReg13Lt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.115 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginReg13Nt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.116 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginReg14Lt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.117 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of the line. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginReg14Nt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.118 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of the line. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginReg23Lt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.119 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of the line. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginReg23Nt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.120 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of the line. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginReg24Lt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.121 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of the line. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginReg24Nt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.122 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of the line. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginReg33Lt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.123 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of the line. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginReg33Nt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.124 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of the line. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginReg34Lt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.125 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of the line. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginReg34Nt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.126 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of the line. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginReg43Lt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.127 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of the line. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginReg43Nt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.128 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of the line. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginReg44Lt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.129 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of the line. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginReg44Nt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.130 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of the line. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginReg53Lt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.131 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of the line. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginReg53Nt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.132 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of the line. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginReg54Lt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.133 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of the line. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginReg54Nt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.134 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of the line. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginReg63Lt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.135 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of the line. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginReg63Nt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.136 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of the line. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginReg64Lt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.137 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of the line. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginReg64Nt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.138 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of the line. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginReg73Lt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.139 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of the line. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginReg73Nt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.140 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of the line. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginReg74Lt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.141 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginReg74Nt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.142 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of the line. 0-180 attenuation in steps of 0.5 dB 254 unknown value 255 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginReg83Lt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.143 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of the line. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginReg83Nt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.144 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of the line. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginReg84Lt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.145 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of the line. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| CpmroHdslNoiseMarginReg84Nt | 1.3.6.1.4.1.1887.1.1.4.3.5.1.1.146 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Noise Margin of the line. The value is coded as a signed byte value -63..63 noise margin in steps of 0.5 dB 126 unknown value 127 unsupported variable for addressed device | ||||
| TpmroValueTable | 1.3.6.1.4.1.1887.1.1.4.3.5.2 | NA | mandatory | |
| RpmroValueEntry | 1.3.6.1.4.1.1887.1.1.4.3.5.2.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CpmroValuePortIndex | 1.3.6.1.4.1.1887.1.1.4.3.5.2.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CpmroValueLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.5.2.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CpmroValueCounterIndex | 1.3.6.1.4.1.1887.1.1.4.3.5.2.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the performance counter of a link and is used as index for the other elements in the Table CRC-4 1 LT U-Interface 2 NT U-Interface 3 LT T-Interface incoming 4 LT T-Interface outgoing CRC-6 5 LT Wire pair 1 Direction NT 6 RegA Wire pair 1 Direction LT 7 RegA Wire pair 1 Direction NT 8 NT Wire pair 1 Direction LT 9 LT Wire pair 2 Direction NT 10 RegA Wire pair 2 Direction LT 11 RegA Wire pair 2 Direction NT 12 NT Wire pair 2 Direction LT | ||||
| CpmroCounter | 1.3.6.1.4.1.1887.1.1.4.3.5.2.1.4 | OCTET STRING (SIZE (96)) | RO | mandatory |
column · OCTET STRING (SIZE (96)) · read-only · mandatory This octet string contains the performance data of the performance counter addressed through the index. The performance values are stored as 4 byte values, MSB first. They are mapped as follows: Byte Interval Variable 0..3 Current 15 Minutes Elapsed Time 4..7 Current 15 Minutes Block Errors 8..11 Current 15 Minutes Background Block Errors 12..15 Current 15 Minutes Errored Seconds 16..19 Current 15 Minutes Severely Errored Seconds 20..23 Current 15 Minutes Unavailable Time 24..27 Last 15 Minutes Elapsed Time 28..31 Last 15 Minutes Block Errors 32..35 Last 15 Minutes Background Block Errors 36..39 Last 15 Minutes Errored Seconds 40..43 Last 15 Minutes Severely Errored Seconds 44..47 Last 15 Minutes Unavailable Time 48..51 Current 24 Hours Elapsed Time 52..55 Current 24 Hours Block Errors 56..59 Current 24 Hours Background Block Errors 60..63 Current 24 Hours Errored Seconds 64..67 Current 24 Hours Severely Errored Seconds 68..71 Current 24 Hours Unavailable Time 72..75 Last 24 Hours Elapsed Time 76..79 Last 24 Hours Block Errors 80..83 Last 24 Hours Background Block Errors 84..87 Last 24 Hours Errored Seconds 88..91 Last 24 Hours Severely Errored Seconds 92..95 Last 24 Hours Unavailable Time The variables have the following ranges: 15 Minute Intervals: ET, ES, SES, UT 0..900 Seconds BE, BBE 0..300'000 Errors 24 Hour Intervals ET, ES, SES, UT 0..86'400 Seconds BE, BBE 0..28'800'00 Errors All Variables can contain the following values to indicate undefined results: HEX DEC Meaning 0xfffffffd (-3) Disabled (the proxy does not store values for this link) 0xfffffffe (-2) Unsupported variable for addressed device 0xffffffff (-1) Unknown value | ||||
| TpmroStuValueTable | 1.3.6.1.4.1.1887.1.1.4.3.5.3 | NA | mandatory | |
| RpmroStuValueEntry | 1.3.6.1.4.1.1887.1.1.4.3.5.3.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CpmroStuValuePortIndex | 1.3.6.1.4.1.1887.1.1.4.3.5.3.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CpmroStuValueLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.5.3.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CpmroStuValueCounterIndex | 1.3.6.1.4.1.1887.1.1.4.3.5.3.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the performance counter of a link
and is used as index for the other elements in the Table
CRC-4
1 LT U-Interface
2 NT U-Interface
3 LT V-Interface incoming
4 LT V-Interface outgoing
13 NT T-Interface incoming
14 NT T-Interface outgoing
CRC-6
5 LT Wire pair 1 Direction NT
6 Reg1 Wire pair 1 Direction LT
7 Reg1 Wire pair 1 Direction NT
8 NT Wire pair 1 Direction LT
9 LT Wire pair 2 Direction NT
10 Reg1 Wire pair 2 Direction LT
11 Reg1 Wire pair 2 Direction NT
12 NT Wire pair 2 Direction LT
15 Reg2 Wire pair 1 Direction LT
16 Reg2 Wire pair 1 Direction NT
17 Reg2 Wire pair 2 Direction LT
18 Reg2 Wire pair 2 Direction NT
19 Reg3 Wire pair 1 Direction LT
20 Reg3 Wire pair 1 Direction NT
21 Reg4 Wire pair 1 Direction LT
22 Reg4 Wire pair 1 Direction NT
23 Reg5 Wire pair 1 Direction LT
24 Reg5 Wire pair 1 Direction NT
25 Reg6 Wire pair 1 Direction LT
26 Reg6 Wire pair 1 Direction NT
27 Reg7 Wire pair 1 Direction LT
28 Reg7 Wire pair 1 Direction NT
29 Reg8 Wire pair 1 Direction LT
30 Reg8 Wire pair 1 Direction NT
31 Reg3 Wire pair 2 Direction LT
32 Reg3 Wire pair 2 Direction NT
33 Reg4 Wire pair 2 Direction LT
34 Reg4 Wire pair 2 Direction NT
35 Reg5 Wire pair 2 Direction LT
36 Reg5 Wire pair 2 Direction NT
37 Reg6 Wire pair 2 Direction LT
38 Reg6 Wire pair 2 Direction NT
39 Reg7 Wire pair 2 Direction LT
40 Reg7 Wire pair 2 Direction NT
41 Reg8 Wire pair 2 Direction LT
42 Reg8 Wire pair 2 Direction NT
43 Reg1 Wire pair 3 Direction LT
44 Reg1 Wire pair 3 Direction NT
45 Reg2 Wire pair 3 Direction LT
46 Reg2 Wire pair 3 Direction NT
47 Reg3 Wire pair 3 Direction LT
48 Reg3 Wire pair 3 Direction NT
49 Reg4 Wire pair 3 Direction LT
50 Reg4 Wire pair 3 Direction NT
59 Reg1 Wire pair 4 Direction LT
60 Reg1 Wire pair 4 Direction NT
61 Reg2 Wire pair 4 Direction LT
62 Reg2 Wire pair 4 Direction NT
63 Reg3 Wire pair 4 Direction LT
64 Reg3 Wire pair 4 Direction NT
65 Reg4 Wire pair 4 Direction LT
66 Reg4 Wire pair 4 Direction NT
75 LT Wire pair 3 Direction NT
76 NT Wire pair 3 Direction LT
77 LT Wire pair 4 Direction NT
78 NT Wire pair 4 Direction LT
FAS and BPV
79 FAS-V/T error local
80 BPV-V/T local
81 FAS-T error far
82 BPV-T far
83 V_A CRC4
84 V_A Ebit
85 V_B CRC4
86 V_B Ebit
87 V_C CRC4
88 V_C Ebit
89 V_D CRC4
90 V_D Ebit
91 MCS Ch a LT
92 MCS Ch b LT
93 MCS Ch c LT
94 MCS Ch d LT
96 MCS Ch a NT
97 MCS Ch b NT
98 MCS Ch c NT
99 MCS Ch d NT
101 Far end MCS Ch a NT
102 Far end MCS Ch b NT
103 Far end MCS Ch c NT
104 Far end MCS Ch d NT
106 Far end MCS Ch a LT
107 Far end MCS Ch b LT
108 Far end MCS Ch c LT
109 Far end MCS Ch d LT
113 V_A CRC4 far
114 V_A Ebit far
115 V_B CRC4 far
116 V_B Ebit far
117 V_C CRC4 far
118 V_C Ebit far
119 V_D CRC4 far
120 V_D Ebit far | ||||
| CpmroStuValueIntervalIndex | 1.3.6.1.4.1.1887.1.1.4.3.5.3.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the performance interval pair of a link and is used as index for the other elements in the Table The following values are supported: Index Interval 1 Interval 2 1 Current Last 1 2 Last 2 Last 3 3 Last 4 Last 5 4 Last 6 Last 7 5 Last 8 Last 9 6 Last 10 Last 11 7 Last 12 Last 13 8 Last 14 Last 15 9 Last 16 Last 17 10 Last 18 Last 19 11 Last 20 Last 21 12 Last 22 Last 23 13 Last 24 Last 25 14 Last 26 Last 27 15 Last 28 Last 29 16 Last 30 Last 31 17 Last 32 unused | ||||
| CpmroStuCounter | 1.3.6.1.4.1.1887.1.1.4.3.5.3.1.5 | OCTET STRING (SIZE (96)) | RO | mandatory |
column · OCTET STRING (SIZE (96)) · read-only · mandatory This octet string contains the performance data of the performance counter addressed through the index. The performance values are stored as 4 byte values, MSB first. They are mapped as follows: Byte Interval Variable 0..3 Interval 1 - 15 Minutes Elapsed Time 4..7 Interval 1 - 15 Minutes Block Errors 8..11 Interval 1 - 15 Minutes LOSW Seconds 12..15 Interval 1 - 15 Minutes Errored Seconds 16..19 Interval 1 - 15 Minutes Severely Errored Seconds 20..23 Interval 1 - 15 Minutes Unavailable Time 24..27 Interval 2 - 15 Minutes Elapsed Time 28..31 Interval 2 - 15 Minutes Block Errors 32..35 Interval 2 - 15 Minutes LOSW Seconds 36..39 Interval 2 - 15 Minutes Errored Seconds 40..43 Interval 2 - 15 Minutes Severely Errored Seconds 44..47 Interval 2 - 15 Minutes Unavailable Time 48..51 Interval 1 - 24 Hours Elapsed Time 52..55 Interval 1 - 24 Hours Block Errors 56..59 Interval 1 - 24 Hours LOSW Seconds 60..63 Interval 1 - 24 Hours Errored Seconds 64..67 Interval 1 - 24 Hours Severely Errored Seconds 68..71 Interval 1 - 24 Hours Unavailable Time 72..75 Interval 2 - 24 Hours Elapsed Time 76..79 Interval 2 - 24 Hours Block Errors 80..83 Interval 2 - 24 Hours LOSW Seconds 84..87 Interval 2 - 24 Hours Errored Seconds 88..91 Interval 2 - 24 Hours Severely Errored Seconds 92..95 Interval 2 - 24 Hours Unavailable Time The variables have the following ranges: 15 Minute Intervals: ET, ES, SES, LOSWS, UT 0..900 Seconds BE 0..300'000 Errors 24 Hour Intervals ET, ES, SES, LOSWS, UT 0..86'400 Seconds BE 0..28'800'00 Errors All Variables can contain the following values to indicate undefined results: HEX DEC Meaning 0xfffffffd (-3) Disabled (the proxy does not store values for this link) 0xfffffffe (-2) Unsupported variable for addressed device 0xffffffff (-1) Unknown value | ||||
| TpmroApc15Table | 1.3.6.1.4.1.1887.1.1.4.3.5.4 | NA | mandatory | |
| RpmroApc15Entry | 1.3.6.1.4.1.1887.1.1.4.3.5.4.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CpmroApc15PortIndex | 1.3.6.1.4.1.1887.1.1.4.3.5.4.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CpmroApc15LinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.5.4.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CpmroApc15CounterIndex | 1.3.6.1.4.1.1887.1.1.4.3.5.4.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the performance counter of a link and is used as index for the other elements in the Table | ||||
| CpmroApc15BlockErrors | 1.3.6.1.4.1.1887.1.1.4.3.5.4.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This is an unused dummy variable which is used by the Automatic Performance Collection (APC) and does not exist on the proxy which means that it will never be answered. | ||||
| CpmroApc15BackgroundBlockErrors | 1.3.6.1.4.1.1887.1.1.4.3.5.4.1.5 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This is an unused dummy variable which is used by the Automatic Performance Collection (APC) and does not exist on the proxy which means that it will never be answered. | ||||
| CpmroApc15ErroredSeconds | 1.3.6.1.4.1.1887.1.1.4.3.5.4.1.6 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This is an unused dummy variable which is used by the Automatic Performance Collection (APC) and does not exist on the proxy which means that it will never be answered. | ||||
| CpmroApc15SeverelyErroredSeconds | 1.3.6.1.4.1.1887.1.1.4.3.5.4.1.7 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This is an unused dummy variable which is used by the Automatic Performance Collection (APC) and does not exist on the proxy which means that it will never be answered. | ||||
| CpmroApc15UnavailableTime | 1.3.6.1.4.1.1887.1.1.4.3.5.4.1.8 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This is an unused dummy variable which is used by the Automatic Performance Collection (APC) and does not exist on the proxy which means that it will never be answered. | ||||
| TpmroApc24Table | 1.3.6.1.4.1.1887.1.1.4.3.5.5 | NA | mandatory | |
| RpmroApc24Entry | 1.3.6.1.4.1.1887.1.1.4.3.5.5.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CpmroApc24PortIndex | 1.3.6.1.4.1.1887.1.1.4.3.5.5.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CpmroApc24LinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.5.5.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CpmroApc24CounterIndex | 1.3.6.1.4.1.1887.1.1.4.3.5.5.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the performance counter of a link and is used as index for the other elements in the Table | ||||
| CpmroApc24BlockErrors | 1.3.6.1.4.1.1887.1.1.4.3.5.5.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This is an unused dummy variable which is used by the Automatic Performance Collection (APC) and does not exist on the proxy which means that it will never be answered. | ||||
| CpmroApc24BackgroundBlockErrors | 1.3.6.1.4.1.1887.1.1.4.3.5.5.1.5 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This is an unused dummy variable which is used by the Automatic Performance Collection (APC) and does not exist on the proxy which means that it will never be answered. | ||||
| CpmroApc24ErroredSeconds | 1.3.6.1.4.1.1887.1.1.4.3.5.5.1.6 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This is an unused dummy variable which is used by the Automatic Performance Collection (APC) and does not exist on the proxy which means that it will never be answered. | ||||
| CpmroApc24SeverelyErroredSeconds | 1.3.6.1.4.1.1887.1.1.4.3.5.5.1.7 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This is an unused dummy variable which is used by the Automatic Performance Collection (APC) and does not exist on the proxy which means that it will never be answered. | ||||
| CpmroApc24UnavailableTime | 1.3.6.1.4.1.1887.1.1.4.3.5.5.1.8 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This is an unused dummy variable which is used by the Automatic Performance Collection (APC) and does not exist on the proxy which means that it will never be answered. | ||||
| TpmroBerTable | 1.3.6.1.4.1.1887.1.1.4.3.5.6 | NA | mandatory | |
| RpmroBerEntry | 1.3.6.1.4.1.1887.1.1.4.3.5.6.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CpmroBerPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.5.6.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CpmroBerLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.5.6.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CpmroBerStatus | 1.3.6.1.4.1.1887.1.1.4.3.5.6.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory State of Bit Error Ration measurement 1 Measurement is finished 2 Measurement is still in progress 3 Measurement is still trying to find synchronisation 4 Measurement failed to find synchronisation 5 Measurement has been (aborted) 6 Measurement has not yet been started 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CpmroBerInterval | 1.3.6.1.4.1.1887.1.1.4.3.5.6.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The interval of the current or last measurement 2 OneMin The measurement duration is/was 1 minute 3 TenMin The measurement duration is/was 10 minutes 4 OneHour The measurement duration is/was 1 hour 5 OneDay The measurement duration is/was 24 hours 6 OneMinDirV The measurement duration is/was 1 minute (direction V) 7 TenMinDirV The measurement duration is/was 10 minutes (direction V) 8 OneHourDirV The measurement duration is/was 1 hour (direction V) 9 OneDayDirV The measurement duration is/was 24 hours (direction V) 10 OneMinRoundTrip The measurement duration is/was 1 minute (round trip) 11 TenMinRoundTrip The measurement duration is/was 10 minutes (round trip) 12 OneHourRoundTrip The measurement duration is/was 1 hour (round trip) 13 OneDayRoundTrip The measurement duration is/was 24 hours (round trip) 14 OneMinMCS The measurement duration is/was 1 minute (MCS) 15 TenMinMCS The measurement duration is/was 10 minutes (MCS) 16 OneHourMCS The measurement duration is/was 1 hour (MCS) 17 OneDayMCS The measurement duration is/was 24 hours (MCS) 18 OneMinData The measurement duration is/was 1 minute (Data) 19 TenMinData The measurement duration is/was 10 minutes (Data) 20 OneHourData The measurement duration is/was 1 hour (Data) 21 OneDayData The measurement duration is/was 24 hours (Data) 22 OneMinMCSLocal The measurement duration is/was 1 minute (MCSLocal) 23 TenMinMCSLocal The measurement duration is/was 10 minutes (MCSLocal) 24 OneHourMCSLocal The measurement duration is/was 1 hour (MCSLocal) 25 OneDayMCSLocal The measurement duration is/was 24 hours (MCSLocal) 26 OneMinG703If The measurement duration is/was 1 minute (G.703 Interface) 27 TenMinG703If The measurement duration is/was 10 minutes (G.703 Interface) 28 OneHourG703If The measurement duration is/was 1 hour (G.703 Interface) 29 OneDayG703If The measurement duration is/was 24 hours (G.703 Interface) 30 OneMinDataIf The measurement duration is/was 1 minute (Data Interface) 31 TenMinDataIf The measurement duration is/was 10 minutes (Data Interface) 32 OneHourDataIf The measurement duration is/was 1 hour (Data Interface) 33 OneDayDataIf The measurement duration is/was 24 hours (Data Interface) 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CpmroBerElapsedTime | 1.3.6.1.4.1.1887.1.1.4.3.5.6.1.5 | INTEGER (0..4294967295) | RO | mandatory |
column · INTEGER (0..4294967295) · read-only · mandatory Elapsed time of measurement. During synchronisation (pmroBerStatus=search) this indicates how long the device has been searching for synchronistation. Once synchronisation has been found (pmroBerStatus=running), this indicates how long the measurement has been running. 0..86'400 Elapsed time in seconds 0xfffffffe Unknown value 0xffffffff Unsupported variable for addressed device | ||||
| CpmroBerSynchLoss | 1.3.6.1.4.1.1887.1.1.4.3.5.6.1.6 | INTEGER (0..4294967295) | RO | mandatory |
column · INTEGER (0..4294967295) · read-only · mandatory Time without synchronisation. During synchronisation (pmroBerStatus=search) this indicates how long the device has been searching for synchronistation and corresponds to pmroBerElapsedTime. Once synchronisation has been found (pmroBerStatus=running), this indicates how many seconds during the measurement synchronisation has been (temporarily) lost. 0..86'40000 Number of seconds without synchronisation 0xfffffffe Unknown value 0xffffffff Unsupported variable for addressed device | ||||
| CpmroBerNumErrs | 1.3.6.1.4.1.1887.1.1.4.3.5.6.1.7 | INTEGER (0..4294967295) | RO | mandatory |
column · INTEGER (0..4294967295) · read-only · mandatory Number of bit errors which occurred during the Bit Error Ratio measurement 0..4'294'967'292 Effective number of errors 0xfffffffd More than 4'294'967'292 errors 0xfffffffe Unknown value 0xffffffff Unsupported variable for addressed device | ||||
| CpmroBerErrorFreeSeconds | 1.3.6.1.4.1.1887.1.1.4.3.5.6.1.8 | INTEGER (0..4294967295) | RO | mandatory |
column · INTEGER (0..4294967295) · read-only · mandatory Number of error free seconds during the measurement. This can be used to determine whether errors are 'bursty', i.e. occurring only during a short period of time (when the number of error free seconds is close to the elapsed time) or continuous (when the number of error free seconds is low). 0..86'400 Error free seconds during measurement 0xfffffffe Unknown value 0xffffffff Unsupported variable for addressed device | ||||
| CpmroBerResultMcsChannelA | 1.3.6.1.4.1.1887.1.1.4.3.5.6.1.9 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory BER test result for MCS channel a: 1 Test was error free on this MCS channel 2 Test showed errors on this MCS channel 3 No pattern on this MCS channel found while test 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CpmroBerResultMcsChannelB | 1.3.6.1.4.1.1887.1.1.4.3.5.6.1.10 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory BER test result for MCS channel b: 1 Test was error free on this MCS channel 2 Test showed errors on this MCS channel 3 No pattern on this MCS channel found while test 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CpmroBerResultMcsChannelC | 1.3.6.1.4.1.1887.1.1.4.3.5.6.1.11 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory BER test result for MCS channel c: 1 Test was error free on this MCS channel 2 Test showed errors on this MCS channel 3 No pattern on this MCS channel found while test 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CpmroBerResultMcsChannelD | 1.3.6.1.4.1.1887.1.1.4.3.5.6.1.12 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory BER test result for MCS channel d: 1 Test was error free on this MCS channel 2 Test showed errors on this MCS channel 3 No pattern on this MCS channel found while test 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| TpmroLineProbeTable | 1.3.6.1.4.1.1887.1.1.4.3.5.7 | NA | mandatory | |
| RpmroLineProbeEntry | 1.3.6.1.4.1.1887.1.1.4.3.5.7.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CpmroLineProbePortIndex | 1.3.6.1.4.1.1887.1.1.4.3.5.7.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CpmroLineProbeLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.5.7.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CpmroLineProbeStatus | 1.3.6.1.4.1.1887.1.1.4.3.5.7.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory State of Line Probing 1 Done Probing is finished 2 Running Probing is still in progress 3 Failed Probing failed 4 Abort Probing has been aborted 5 Norun Probing has never been started 254 Unknown value 255 Unsupported variable for addressed device
| ||||
| CpmroLineProbeBandwidthMask | 1.3.6.1.4.1.1887.1.1.4.3.5.7.1.4 | OCTET STRING (SIZE (6)) | RO | mandatory |
column · OCTET STRING (SIZE (6)) · read-only · mandatory Bandwidths used for line probing Bandwidth Byte 0 bit 0 reserved bit 1 reserved bit 2 192 kbit/s bit 3 256 kbit/s bit 4 320 kbit/s bit 5 384 kbit/s bit 6 448 kbit/s bit 7 512 kbit/s Byte 1 bit 0 576 kbit/s bit 1 640 kbit/s bit 2 704 kbit/s bit 3 768 kbit/s bit 4 832 kbit/s bit 5 896 kbit/s bit 6 960 kbit/s bit 7 1024 kbit/s Byte 2 bit 0 1088 kbit/s bit 1 1152 kbit/s bit 2 1216 kbit/s bit 3 1280 kbit/s bit 4 1344 kbit/s bit 5 1408 kbit/s bit 6 1472 kbit/s bit 7 1536 kbit/s Byte 3 bit 0 1600 kbit/s bit 1 1664 kbit/s bit 2 1728 kbit/s bit 3 1792 kbit/s bit 4 1856 kbit/s bit 5 1920 kbit/s bit 6 1984 kbit/s bit 7 2048 kbit/s Byte 4 bit 0 2112 kbit/s bit 1 2176 kbit/s bit 2 2240 kbit/s bit 3 2304 kbit/s bit 4 unused bit 5 unused bit 6 unused bit 7 unused Byte 5 contains a value specifying the validity of the result of a read operation: 1 Ok Values returned are valid 254 unknown values 255 unsupported variable for addressed device | ||||
| CpmroLineProbeSNRMargin | 1.3.6.1.4.1.1887.1.1.4.3.5.7.1.5 | OCTET STRING (SIZE (36)) | RO | mandatory |
column · OCTET STRING (SIZE (36)) · read-only · mandatory Each byte contains as result of the line probe the SNR margin for the bandwidth corresponding to the byte number The value for each byte is coded as follows: -127..+127 SNR margin in dB -128 Unknown value | ||||
| CpmroLineProbeSNRMarginWire2 | 1.3.6.1.4.1.1887.1.1.4.3.5.7.1.6 | OCTET STRING (SIZE (36)) | RO | mandatory |
column · OCTET STRING (SIZE (36)) · read-only · mandatory Each byte contains as result of the line probe the SNR margin for the bandwidth corresponding to the byte number The value for each byte is coded as follows: -127..+127 SNR margin in dB -128 Unknown value | ||||
| CpmroLineProbeSNRMarginWire3 | 1.3.6.1.4.1.1887.1.1.4.3.5.7.1.7 | OCTET STRING (SIZE (36)) | RO | mandatory |
column · OCTET STRING (SIZE (36)) · read-only · mandatory Each byte contains as result of the line probe the SNR margin for the bandwidth corresponding to the byte number The value for each byte is coded as follows: -127..+127 SNR margin in dB -128 Unknown value | ||||
| CpmroLineProbeSNRMarginWire4 | 1.3.6.1.4.1.1887.1.1.4.3.5.7.1.8 | OCTET STRING (SIZE (36)) | RO | mandatory |
column · OCTET STRING (SIZE (36)) · read-only · mandatory Each byte contains as result of the line probe the SNR margin for the bandwidth corresponding to the byte number The value for each byte is coded as follows: -127..+127 SNR margin in dB -128 Unknown value | ||||
| TpmroLocalL2SwitchValueTable | 1.3.6.1.4.1.1887.1.1.4.3.5.8 | NA | mandatory | |
| RpmroLocalL2SwitchValueEntry | 1.3.6.1.4.1.1887.1.1.4.3.5.8.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CpmroLocalL2SwitchValuePortIndex | 1.3.6.1.4.1.1887.1.1.4.3.5.8.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CpmroLocalL2SwitchValueLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.5.8.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CpmroLocalL2SwitchValueCounterIndex | 1.3.6.1.4.1.1887.1.1.4.3.5.8.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the performance counter of a link and is used as index for the other elements in the Table 1 WAN Port 2 LAN Port 1 3 LAN Port 2 4 LAN Port 3 5 LAN Port 4 | ||||
| CpmroLocalL2SwitchRxCounter | 1.3.6.1.4.1.1887.1.1.4.3.5.8.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This value indicates the number of Rx packets / frames on a L2Switch port, depending on the type of port: WAN Port Number of Frames LAN Port x Number of Packets The counters count as far as the decimal equivalend of 0xfffffffd and then roll over to 0. 0xfffffffe Unsupported value 0xffffffff Unknown value | ||||
| CpmroLocalL2SwitchTxCounter | 1.3.6.1.4.1.1887.1.1.4.3.5.8.1.5 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This value indicates the number of Tx packets / frames on a L2Switch port, depending on the type of port: WAN Port Number of Frames LAN Port x Number of Packets The counters count as far as the decimal equivalend of 0xfffffffd and then roll over to 0. 0xfffffffe Unsupported value 0xffffffff Unknown value | ||||
| CpmroLocalL2SwitchErrCounter | 1.3.6.1.4.1.1887.1.1.4.3.5.8.1.6 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This value indicates the number of errored packets / frames on a L2Switch port, depending on the type of port: WAN Port Number of Frames LAN Port x Number of Packets The counters count as far as the decimal equivalend of 0xfffffffd and then roll over to 0. 0xfffffffe Unsupported value 0xffffffff Unknown value | ||||
| TpmroFarL2SwitchValueTable | 1.3.6.1.4.1.1887.1.1.4.3.5.9 | NA | mandatory | |
| RpmroFarL2SwitchValueEntry | 1.3.6.1.4.1.1887.1.1.4.3.5.9.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CpmroFarL2SwitchValuePortIndex | 1.3.6.1.4.1.1887.1.1.4.3.5.9.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CpmroFarL2SwitchValueLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.5.9.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CpmroFarL2SwitchValueCounterIndex | 1.3.6.1.4.1.1887.1.1.4.3.5.9.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the performance counter of a link and is used as index for the other elements in the Table 1 WAN Port 2 LAN Port 1 3 LAN Port 2 4 LAN Port 3 5 LAN Port 4 | ||||
| CpmroFarL2SwitchRxCounter | 1.3.6.1.4.1.1887.1.1.4.3.5.9.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This value indicates the number of Rx packets / frames on a L2Switch port, depending on the type of port: WAN Port Number of Frames LAN Port x Number of Packets The counters count as far as the decimal equivalend of 0xfffffffd and then roll over to 0. 0xfffffffe Unsupported value 0xffffffff Unknown value | ||||
| CpmroFarL2SwitchTxCounter | 1.3.6.1.4.1.1887.1.1.4.3.5.9.1.5 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This value indicates the number of Tx packets / frames on a L2Switch port, depending on the type of port: WAN Port Number of Frames LAN Port x Number of Packets The counters count as far as the decimal equivalend of 0xfffffffd and then roll over to 0. 0xfffffffe Unsupported value 0xffffffff Unknown value | ||||
| CpmroFarL2SwitchErrCounter | 1.3.6.1.4.1.1887.1.1.4.3.5.9.1.6 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This value indicates the number of errored packets / frames on a L2Switch port, depending on the type of port: WAN Port Number of Frames LAN Port x Number of Packets The counters count as far as the decimal equivalend of 0xfffffffd and then roll over to 0. 0xfffffffe Unsupported value 0xffffffff Unknown value | ||||
| TpmroPBOCurrentValueTable | 1.3.6.1.4.1.1887.1.1.4.3.5.10 | NA | mandatory | |
| RpmroPBOCurrentValueEntry | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CpmroPBOCurrentValuePortIndex | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CpmroPBOCurrentValueLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CpmroPBOCurrentValueLtWp1 | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for LT, Wire pair 1, Direction NT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueLtWp2 | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for LT, Wire pair 2, Direction NT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueNtWp1 | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.5 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for NT, Wire pair 1, Direction LT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueNtWp2 | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.6 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for NT, Wire pair 2, Direction LT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueReg1Wp1DirLt | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.7 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for Reg1, Wire pair 1, Direction LT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueReg1Wp1DirNt | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.8 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for Reg1, Wire pair 1, Direction NT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueReg1Wp2DirLt | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.9 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for Reg1, Wire pair 2, Direction LT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueReg1Wp2DirNt | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.10 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for Reg1, Wire pair 2, Direction NT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueReg2Wp1DirLt | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.11 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for Reg2, Wire pair 1, Direction LT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueReg2Wp1DirNt | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.12 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for Reg2, Wire pair 1, Direction NT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueReg2Wp2DirLt | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.13 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for Reg2, Wire pair 2, Direction LT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueReg2Wp2DirNt | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.14 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for Reg2, Wire pair 2, Direction NT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueReg3Wp1DirLt | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.15 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for Reg3, Wire pair 1, Direction LT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueReg3Wp1DirNt | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.16 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for Reg3, Wire pair 1, Direction NT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueReg3Wp2DirLt | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.17 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for Reg3, Wire pair 2, Direction LT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueReg3Wp2DirNt | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.18 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for Reg3, Wire pair 2, Direction NT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueReg4Wp1DirLt | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.19 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for Reg4, Wire pair 1, Direction LT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueReg4Wp1DirNt | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.20 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for Reg4, Wire pair 1, Direction NT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueReg4Wp2DirLt | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.21 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for Reg4, Wire pair 2, Direction LT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueReg4Wp2DirNt | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.22 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for Reg4, Wire pair 2, Direction NT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueReg5Wp1DirLt | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.23 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for Reg5, Wire pair 1, Direction LT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueReg5Wp1DirNt | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.24 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for Reg5, Wire pair 1, Direction NT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueReg5Wp2DirLt | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.25 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for Reg5, Wire pair 2, Direction LT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueReg5Wp2DirNt | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.26 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for Reg5, Wire pair 2, Direction NT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueReg6Wp1DirLt | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.27 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for Reg6, Wire pair 1, Direction LT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueReg6Wp1DirNt | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.28 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for Reg6, Wire pair 1, Direction NT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueReg6Wp2DirLt | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.29 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for Reg6, Wire pair 2, Direction LT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueReg6Wp2DirNt | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.30 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for Reg6, Wire pair 2, Direction NT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueReg7Wp1DirLt | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.31 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for Reg7, Wire pair 1, Direction LT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueReg7Wp1DirNt | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.32 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for Reg7, Wire pair 1, Direction NT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueReg7Wp2DirLt | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.33 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for Reg7, Wire pair 2, Direction LT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueReg7Wp2DirNt | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.34 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for Reg7, Wire pair 2, Direction NT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueReg8Wp1DirLt | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.35 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for Reg8, Wire pair 1, Direction LT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueReg8Wp1DirNt | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.36 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for Reg8, Wire pair 1, Direction NT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueReg8Wp2DirLt | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.37 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for Reg8, Wire pair 2, Direction LT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueReg8Wp2DirNt | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.38 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for Reg8, Wire pair 2, Direction NT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueLtWp3 | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.39 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for LT, Wire pair 3, Direction NT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueLtWp4 | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.40 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for LT, Wire pair 4, Direction NT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueNtWp3 | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.41 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for NT, Wire pair 3, Direction LT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueNtWp4 | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.42 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for NT, Wire pair 4, Direction LT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueReg1Wp3DirLt | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.43 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for Reg1, Wire pair 3, Direction LT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueReg1Wp3DirNt | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.44 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for Reg1, Wire pair 3, Direction NT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueReg1Wp4DirLt | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.45 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for Reg1, Wire pair 4, Direction LT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueReg1Wp4DirNt | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.46 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for Reg1, Wire pair 4, Direction NT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueReg2Wp3DirLt | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.47 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for Reg2, Wire pair 3, Direction LT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueReg2Wp3DirNt | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.48 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for Reg2, Wire pair 3, Direction NT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueReg2Wp4DirLt | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.49 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for Reg2, Wire pair 4, Direction LT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueReg2Wp4DirNt | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.50 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for Reg2, Wire pair 4, Direction NT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueReg3Wp3DirLt | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.51 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for Reg3, Wire pair 3, Direction LT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueReg3Wp3DirNt | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.52 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for Reg3, Wire pair 3, Direction NT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueReg3Wp4DirLt | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.53 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for Reg3, Wire pair 4, Direction LT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueReg3Wp4DirNt | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.54 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for Reg3, Wire pair 4, Direction NT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueReg4Wp3DirLt | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.55 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for Reg4, Wire pair 3, Direction LT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueReg4Wp3DirNt | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.56 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for Reg4, Wire pair 3, Direction NT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueReg4Wp4DirLt | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.57 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for Reg4, Wire pair 4, Direction LT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueReg4Wp4DirNt | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.58 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for Reg4, Wire pair 4, Direction NT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueReg5Wp3DirLt | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.59 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for Reg5, Wire pair 3, Direction LT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueReg5Wp3DirNt | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.60 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for Reg5, Wire pair 3, Direction NT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueReg5Wp4DirLt | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.61 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for Reg5, Wire pair 4, Direction LT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueReg5Wp4DirNt | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.62 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for Reg5, Wire pair 4, Direction NT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueReg6Wp3DirLt | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.63 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for Reg6, Wire pair 3, Direction LT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueReg6Wp3DirNt | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.64 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for Reg6, Wire pair 3, Direction NT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueReg6Wp4DirLt | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.65 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for Reg6, Wire pair 4, Direction LT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueReg6Wp4DirNt | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.66 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for Reg6, Wire pair 4, Direction NT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueReg7Wp3DirLt | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.67 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for Reg7, Wire pair 3, Direction LT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueReg7Wp3DirNt | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.68 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for Reg7, Wire pair 3, Direction NT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueReg7Wp4DirLt | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.69 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for Reg7, Wire pair 4, Direction LT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueReg7Wp4DirNt | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.70 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for Reg7, Wire pair 4, Direction NT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueReg8Wp3DirLt | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.71 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for Reg8, Wire pair 3, Direction LT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueReg8Wp3DirNt | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.72 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for Reg8, Wire pair 3, Direction NT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueReg8Wp4DirLt | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.73 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for Reg8, Wire pair 4, Direction LT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmroPBOCurrentValueReg8Wp4DirNt | 1.3.6.1.4.1.1887.1.1.4.3.5.10.1.74 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current PowerBackOff value for Reg8, Wire pair 4, Direction NT 1..32 Db0..Db31 Current PBO value 130..133 DbMin1..DbMin4 Current PBO value (negative, Power Boost). 254 unknown value 255 unsupported variable for addressed device
| ||||
| Npmrw | 1.3.6.1.4.1.1887.1.1.4.3.6 | |||
| TpmrwActionTable | 1.3.6.1.4.1.1887.1.1.4.3.6.1 | NA | mandatory | |
| RpmrwActionEntry | 1.3.6.1.4.1.1887.1.1.4.3.6.1.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CpmrwActionPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.6.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CpmrwActionLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.6.1.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CpmrwActionResetPM | 1.3.6.1.4.1.1887.1.1.4.3.6.1.1.3 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory This is a write-only variable which is used to reset all currently running CRC-based performance counters and starts a new measurement interval. This command resets all 15 minute and 24 hour counters for all current counters and the stored last interval. The only legal parameter is 'reset(1)'.
| ||||
| CpmrwActionBerStart | 1.3.6.1.4.1.1887.1.1.4.3.6.1.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory This is a write-only variable which is used to start (and stop) the Bit Error Ration measurement. 1 Abort Stop a running BER measurement 2 OneMin Start a BER measurement for the duration of 1 minute 3 TenMin Start a BER measurement for the duration of 10 minutes 4 OneHour Start a BER measurement for the duration of 1 hour 5 OneDay Start a BER measurement for the duration of 24 hours 6 OneMinDirV Start a BER measurement duration is/was 1 minute (direction V) 7 TenMinDirV Start a BER measurement duration is/was 10 minutes (direction V) 8 OneHourDirV Start a BER measurement duration is/was 1 hour (direction V) 9 OneDayDirV Start a BER measurement duration is/was 24 hours (direction V) 10 OneMinRoundTrip Start a BER measurement duration is/was 1 minute (round trip) 11 TenMinRoundTrip Start a BER measurement duration is/was 10 minutes (round trip) 12 OneHourRoundTrip Start a BER measurement duration is/was 1 hour (round trip) 13 OneDayRoundTrip Start a BER measurement duration is/was 24 hours (round trip) 14 OneMinMcs Start a BER measurement duration is/was 1 minute (MCS) 15 TenMinMcs Start a BER measurement duration is/was 10 minutes (MCS) 16 OneHourMcs Start a BER measurement duration is/was 1 hour (MCS) 17 OneDayMcs Start a BER measurement duration is/was 24 hours (MCS) 18 OneMinData Start a BER measurement duration is/was 1 minute (U side Data, var speed) 19 TenMinData Start a BER measurement duration is/was 10 minutes (U side Data, var speed) 20 OneHourData Start a BER measurement duration is/was 1 hour (U side Data, var speed) 21 OneDayData Start a BER measurement duration is/was 24 hours (U side Data, var speed) 22 OneMinMcsLocal Start a BER measurement duration is/was 1 minute (MCS local) 23 TenMinMcsLocal Start a BER measurement duration is/was 10 minutes (MCS local) 24 OneHourMcsLocal Start a BER measurement duration is/was 1 hour (MCS local) 25 OneDayMcsLocal Start a BER measurement duration is/was 24 hours (MCS local) 26 OneMinG703If Start a BER measurement duration is/was 1 minute (G.703 Interface) 27 TenMinG703If Start a BER measurement duration is/was 10 minutes (G.703 Interface) 28 OneHourG703If Start a BER measurement duration is/was 1 hour (G.703 Interface) 29 OneDayG703If Start a BER measurement duration is/was 24 hours (G.703 Interface) 30 OneMinDataIf Start a BER measurement duration is/was 1 minute (Data Interface) 31 TenMinDataIf Start a BER measurement duration is/was 10 minutes (Data Interface) 32 OneHourDataIf Start a BER measurement duration is/was 1 hour (Data Interface) 33 OneDayDataIf Start a BER measurement duration is/was 24 hours (Data Interface) 254 unknown value 255 unsupported variable for addressed device
| ||||
| CpmrwActionProbingStart | 1.3.6.1.4.1.1887.1.1.4.3.6.1.1.5 | OCTET STRING (SIZE (6)) | RW | mandatory |
column · OCTET STRING (SIZE (6)) · read-write · mandatory Selection of bandwidths to use for line probing Bandwidth Byte 0 bit 0 reserved bit 1 reserved bit 2 192 kbit/s bit 3 256 kbit/s bit 4 320 kbit/s bit 5 384 kbit/s bit 6 448 kbit/s bit 7 512 kbit/s Byte 1 bit 0 576 kbit/s bit 1 640 kbit/s bit 2 704 kbit/s bit 3 768 kbit/s bit 4 832 kbit/s bit 5 896 kbit/s bit 6 960 kbit/s bit 7 1024 kbit/s Byte 2 bit 0 1088 kbit/s bit 1 1152 kbit/s bit 2 1216 kbit/s bit 3 1280 kbit/s bit 4 1344 kbit/s bit 5 1408 kbit/s bit 6 1472 kbit/s bit 7 1536 kbit/s Byte 3 bit 0 1600 kbit/s bit 1 1664 kbit/s bit 2 1728 kbit/s bit 3 1792 kbit/s bit 4 1856 kbit/s bit 5 1920 kbit/s bit 6 1984 kbit/s bit 7 2048 kbit/s Byte 4 bit 0 2112 kbit/s bit 1 2176 kbit/s bit 2 2240 kbit/s bit 3 2304 kbit/s bit 4 unused bit 5 unused bit 6 unused bit 7 unused Byte 5 contains a value specifying the validity of the result of a read operation: 1 Ok Values returned are valid 254 unknown values 255 unsupported variable for addressed device | ||||
| CpmrwActionResetPMPacket | 1.3.6.1.4.1.1887.1.1.4.3.6.1.1.6 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory This is a write-only variable which is used to reset all currently running Local L2Switch performance counters. 1 resetLocal Reset local counters 2 resetFar Reset far counters
| ||||
| Ndownload | 1.3.6.1.4.1.1887.1.1.4.3.7 | |||
| TdownloadFarTable | 1.3.6.1.4.1.1887.1.1.4.3.7.1 | NA | mandatory | |
| RdownloadFarEntry | 1.3.6.1.4.1.1887.1.1.4.3.7.1.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CdownloadFarPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.7.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CdownloadFarLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.7.1.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CdownloadFarState | 1.3.6.1.4.1.1887.1.1.4.3.7.1.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Returns the state of the download 1 NotStarted Never started a download for this device 2 Pending Waiting for download start response from NT 3 AbortedLd Remote download not started because of lokal download running 4 ErasingFlash Flash EEPROM of this device is being erased 5 Running Download for this device is running 6 Failed Last download for this device failed 7 Complete Last download for this device was successful 254 unknown value 255 unsupported variable for addressed device
| ||||
| CdownloadFarTotalBlocks | 1.3.6.1.4.1.1887.1.1.4.3.7.1.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Returns the size of the firmware being downloaded to the far device in blocks of 128 bytes 0xFFFE unknown value 0xFFFF unsupported variable for addressed device | ||||
| CdownloadFarProgress | 1.3.6.1.4.1.1887.1.1.4.3.7.1.1.5 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Returns the number of 128 byte blocks that have already been downloaded 0xFFFE unknown value 0xFFFF unsupported variable for addressed device | ||||
| CdownloadFarTarget | 1.3.6.1.4.1.1887.1.1.4.3.7.1.1.6 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Returns the device for which a remote download is active
NotDownloading 1 No remote download is active
Nt 2 Remote download to NT active
Reg11 4 Remote download to regenerator section 1 wire pair 1
Reg12 5 Remote download to regenerator section 1 wire pair 2
Reg21 6 Remote download to regenerator section 2 wire pair 1
Reg22 7 Remote download to regenerator section 2 wire pair 2
Reg31 8 Remote download to regenerator section 3 wire pair 1
Reg32 9 Remote download to regenerator section 3 wire pair 2
Reg41 10 Remote download to regenerator section 4 wire pair 1
Reg42 11 Remote download to regenerator section 4 wire pair 2
Reg51 12 Remote download to regenerator section 5 wire pair 1
Reg52 13 Remote download to regenerator section 5 wire pair 2
Reg61 14 Remote download to regenerator section 6 wire pair 1
Reg62 15 Remote download to regenerator section 6 wire pair 2
Reg71 16 Remote download to regenerator section 7 wire pair 1
Reg72 17 Remote download to regenerator section 7 wire pair 2
Reg81 18 Remote download to regenerator section 8 wire pair 1
Reg82 19 Remote download to regenerator section 8 wire pair 2
Reg13 20 Remote download to regenerator section 1 wire pair 3
Reg14 21 Remote download to regenerator section 1 wire pair 4
Reg23 22 Remote download to regenerator section 2 wire pair 3
Reg24 23 Remote download to regenerator section 2 wire pair 4
Reg33 24 Remote download to regenerator section 3 wire pair 3
Reg34 25 Remote download to regenerator section 3 wire pair 4
Reg43 26 Remote download to regenerator section 4 wire pair 3
Reg44 27 Remote download to regenerator section 4 wire pair 4
Reg53 28 Remote download to regenerator section 5 wire pair 3
Reg54 29 Remote download to regenerator section 5 wire pair 4
Reg63 30 Remote download to regenerator section 6 wire pair 3
Reg64 31 Remote download to regenerator section 6 wire pair 4
Reg73 32 Remote download to regenerator section 7 wire pair 3
Reg74 33 Remote download to regenerator section 7 wire pair 4
Reg83 34 Remote download to regenerator section 8 wire pair 3
Reg84 35 Remote download to regenerator section 8 wire pair 4
254 unknown value
255 unsupported variable for addressed device
| ||||
| TdownloadActionTable | 1.3.6.1.4.1.1887.1.1.4.3.7.2 | NA | mandatory | |
| RdownloadActionEntry | 1.3.6.1.4.1.1887.1.1.4.3.7.2.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CdownloadActionPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.7.2.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CdownloadActionLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.7.2.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CdownloadActionStart | 1.3.6.1.4.1.1887.1.1.4.3.7.2.1.3 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory This is a write-only variable which is used to start remote download from the selcted bank. 1 ActiveBank Use active bank of LT for remote download 2 PassiveBank Use passive bank of LT for remote download 254 unknown value 255 unsupported variable for addressed device
| ||||
| CdownloadActionAbort | 1.3.6.1.4.1.1887.1.1.4.3.7.2.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory This is a write-only variable which is used to abort the currently running remote download. The only legal parameter is 'abort(1)'.
| ||||
| TdownloadSruActionTable | 1.3.6.1.4.1.1887.1.1.4.3.7.3 | NA | mandatory | |
| RdownloadSruActionEntry | 1.3.6.1.4.1.1887.1.1.4.3.7.3.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CdownloadSruActionPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.7.3.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CdownloadSruActionLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.7.3.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CdownloadSruActionRegIndex | 1.3.6.1.4.1.1887.1.1.4.3.7.3.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the regenerator device
| ||||
| CdownloadSruActionStart | 1.3.6.1.4.1.1887.1.1.4.3.7.3.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory This is a write-only variable which is used to start remote download from the selcted bank. 1 ActiveBank Use active bank of LT for remote download 2 PassiveBank Use passive bank of LT for remote download 254 unknown value 255 unsupported variable for addressed device
| ||||
| CdownloadSruActionAbort | 1.3.6.1.4.1.1887.1.1.4.3.7.3.1.5 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory This is a write-only variable which is used to abort the currently running remote download. The only legal parameter is 'abort(1)'.
| ||||
| TdownloadStateTable | 1.3.6.1.4.1.1887.1.1.4.3.7.4 | NA | mandatory | |
| RdownloadStateEntry | 1.3.6.1.4.1.1887.1.1.4.3.7.4.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CdownloadStatePortIndex | 1.3.6.1.4.1.1887.1.1.4.3.7.4.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CdownloadStateLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.7.4.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CdownloadStateInstance | 1.3.6.1.4.1.1887.1.1.4.3.7.4.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Returns the instance of the system for which a download is active
| ||||
| CdownloadStateTarget | 1.3.6.1.4.1.1887.1.1.4.3.7.4.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Returns the device for which a download is active
NotDownloading 1 No download is active
Lt 2 Local download
Nt 3 Remote download to NT active
Reg11 4 Remote download to regenerator section 1 wire pair 1
Reg12 5 Remote download to regenerator section 1 wire pair 2
Reg21 6 Remote download to regenerator section 2 wire pair 1
Reg22 7 Remote download to regenerator section 2 wire pair 2
Reg31 8 Remote download to regenerator section 3 wire pair 1
Reg32 9 Remote download to regenerator section 3 wire pair 2
Reg41 10 Remote download to regenerator section 4 wire pair 1
Reg42 11 Remote download to regenerator section 4 wire pair 2
Reg51 12 Remote download to regenerator section 5 wire pair 1
Reg52 13 Remote download to regenerator section 5 wire pair 2
Reg61 14 Remote download to regenerator section 6 wire pair 1
Reg62 15 Remote download to regenerator section 6 wire pair 2
Reg71 16 Remote download to regenerator section 7 wire pair 1
Reg72 17 Remote download to regenerator section 7 wire pair 2
Reg81 18 Remote download to regenerator section 8 wire pair 1
Reg82 19 Remote download to regenerator section 8 wire pair 2
Reg13 20 Remote download to regenerator section 1 wire pair 3
Reg14 21 Remote download to regenerator section 1 wire pair 4
Reg23 22 Remote download to regenerator section 2 wire pair 3
Reg24 23 Remote download to regenerator section 2 wire pair 4
Reg33 24 Remote download to regenerator section 3 wire pair 3
Reg34 25 Remote download to regenerator section 3 wire pair 4
Reg43 26 Remote download to regenerator section 4 wire pair 3
Reg44 27 Remote download to regenerator section 4 wire pair 4
Reg53 28 Remote download to regenerator section 5 wire pair 3
Reg54 29 Remote download to regenerator section 5 wire pair 4
Reg63 30 Remote download to regenerator section 6 wire pair 3
Reg64 31 Remote download to regenerator section 6 wire pair 4
Reg73 32 Remote download to regenerator section 7 wire pair 3
Reg74 33 Remote download to regenerator section 7 wire pair 4
Reg83 34 Remote download to regenerator section 8 wire pair 3
Reg84 35 Remote download to regenerator section 8 wire pair 4
254 unknown value
255 unsupported variable for addressed device
| ||||
| CdownloadStateState | 1.3.6.1.4.1.1887.1.1.4.3.7.4.1.5 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Returns the state of the download 1 NotStarted Never started a download for this device 2 Pending Waiting for download start response from NT 3 AbortedLd Remote download not started because of lokal download running 4 ErasingFlash Flash EEPROM of this device is being erased 5 Running Download for this device is running 6 Failed Last download for this device failed 7 Complete Last download for this device was successful 254 unknown value 255 unsupported variable for addressed device
| ||||
| CdownloadStateTotalBlocks | 1.3.6.1.4.1.1887.1.1.4.3.7.4.1.6 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Returns the size of the firmware being downloaded to the device in blocks of 128 bytes 0xFFFE unknown value 0xFFFF unsupported variable for addressed device | ||||
| CdownloadStateProgress | 1.3.6.1.4.1.1887.1.1.4.3.7.4.1.7 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Returns the number of 128 byte blocks that have already been downloaded 0xFFFE unknown value 0xFFFF unsupported variable for addressed device | ||||
| TdownloadRemDwlPossibleTable | 1.3.6.1.4.1.1887.1.1.4.3.7.5 | NA | mandatory | |
| RdownloadRemDwlPossibleEntry | 1.3.6.1.4.1.1887.1.1.4.3.7.5.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CdownloadRemDwlPossiblePortIndex | 1.3.6.1.4.1.1887.1.1.4.3.7.5.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CdownloadRemDwlPossibleLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.7.5.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CdownloadRemDwlPossibleNt | 1.3.6.1.4.1.1887.1.1.4.3.7.5.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a remote download is possible or not. The value is bit-coded: bit0 Active bank download possible (far NE compatible) bit1 Active bank download not possible (far NE offline or not compatible) bit2 Active bank unknown, no compatibility list available bit3 not used bit4 Passive bank download possible (far NE compatible) bit5 Passive bank download not possible (far NE offline or not compatible) bit6 Passive bank unknown, no compatibility list available bit7 unsupported variable for addressed device | ||||
| CdownloadRemDwlPossibleReg1Wp1 | 1.3.6.1.4.1.1887.1.1.4.3.7.5.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a remote download is possible or not. The value is bit-coded: bit0 Active bank download possible (far NE compatible) bit1 Active bank download not possible (far NE offline or not compatible) bit2 Active bank unknown, no compatibility list available bit3 not used bit4 Passive bank download possible (far NE compatible) bit5 Passive bank download not possible (far NE offline or not compatible) bit6 Passive bank unknown, no compatibility list available bit7 unsupported variable for addressed device | ||||
| CdownloadRemDwlPossibleReg2Wp1 | 1.3.6.1.4.1.1887.1.1.4.3.7.5.1.5 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a remote download is possible or not. The value is bit-coded: bit0 Active bank download possible (far NE compatible) bit1 Active bank download not possible (far NE offline or not compatible) bit2 Active bank unknown, no compatibility list available bit3 not used bit4 Passive bank download possible (far NE compatible) bit5 Passive bank download not possible (far NE offline or not compatible) bit6 Passive bank unknown, no compatibility list available bit7 unsupported variable for addressed device | ||||
| CdownloadRemDwlPossibleReg3Wp1 | 1.3.6.1.4.1.1887.1.1.4.3.7.5.1.6 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a remote download is possible or not. The value is bit-coded: bit0 Active bank download possible (far NE compatible) bit1 Active bank download not possible (far NE offline or not compatible) bit2 Active bank unknown, no compatibility list available bit3 not used bit4 Passive bank download possible (far NE compatible) bit5 Passive bank download not possible (far NE offline or not compatible) bit6 Passive bank unknown, no compatibility list available bit7 unsupported variable for addressed device | ||||
| CdownloadRemDwlPossibleReg4Wp1 | 1.3.6.1.4.1.1887.1.1.4.3.7.5.1.7 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a remote download is possible or not. The value is bit-coded: bit0 Active bank download possible (far NE compatible) bit1 Active bank download not possible (far NE offline or not compatible) bit2 Active bank unknown, no compatibility list available bit3 not used bit4 Passive bank download possible (far NE compatible) bit5 Passive bank download not possible (far NE offline or not compatible) bit6 Passive bank unknown, no compatibility list available bit7 unsupported variable for addressed device | ||||
| CdownloadRemDwlPossibleReg5Wp1 | 1.3.6.1.4.1.1887.1.1.4.3.7.5.1.8 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a remote download is possible or not. The value is bit-coded: bit0 Active bank download possible (far NE compatible) bit1 Active bank download not possible (far NE offline or not compatible) bit2 Active bank unknown, no compatibility list available bit3 not used bit4 Passive bank download possible (far NE compatible) bit5 Passive bank download not possible (far NE offline or not compatible) bit6 Passive bank unknown, no compatibility list available bit7 unsupported variable for addressed device | ||||
| CdownloadRemDwlPossibleReg6Wp1 | 1.3.6.1.4.1.1887.1.1.4.3.7.5.1.9 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a remote download is possible or not. The value is bit-coded: bit0 Active bank download possible (far NE compatible) bit1 Active bank download not possible (far NE offline or not compatible) bit2 Active bank unknown, no compatibility list available bit3 not used bit4 Passive bank download possible (far NE compatible) bit5 Passive bank download not possible (far NE offline or not compatible) bit6 Passive bank unknown, no compatibility list available bit7 unsupported variable for addressed device | ||||
| CdownloadRemDwlPossibleReg7Wp1 | 1.3.6.1.4.1.1887.1.1.4.3.7.5.1.10 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a remote download is possible or not. The value is bit-coded: bit0 Active bank download possible (far NE compatible) bit1 Active bank download not possible (far NE offline or not compatible) bit2 Active bank unknown, no compatibility list available bit3 not used bit4 Passive bank download possible (far NE compatible) bit5 Passive bank download not possible (far NE offline or not compatible) bit6 Passive bank unknown, no compatibility list available bit7 unsupported variable for addressed device | ||||
| CdownloadRemDwlPossibleReg8Wp1 | 1.3.6.1.4.1.1887.1.1.4.3.7.5.1.11 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a remote download is possible or not. The value is bit-coded: bit0 Active bank download possible (far NE compatible) bit1 Active bank download not possible (far NE offline or not compatible) bit2 Active bank unknown, no compatibility list available bit3 not used bit4 Passive bank download possible (far NE compatible) bit5 Passive bank download not possible (far NE offline or not compatible) bit6 Passive bank unknown, no compatibility list available bit7 unsupported variable for addressed device | ||||
| CdownloadRemDwlPossibleReg1Wp2 | 1.3.6.1.4.1.1887.1.1.4.3.7.5.1.12 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a remote download is possible or not. The value is bit-coded: bit0 Active bank download possible (far NE compatible) bit1 Active bank download not possible (far NE offline or not compatible) bit2 Active bank unknown, no compatibility list available bit3 not used bit4 Passive bank download possible (far NE compatible) bit5 Passive bank download not possible (far NE offline or not compatible) bit6 Passive bank unknown, no compatibility list available bit7 unsupported variable for addressed device | ||||
| CdownloadRemDwlPossibleReg2Wp2 | 1.3.6.1.4.1.1887.1.1.4.3.7.5.1.13 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a remote download is possible or not. The value is bit-coded: bit0 Active bank download possible (far NE compatible) bit1 Active bank download not possible (far NE offline or not compatible) bit2 Active bank unknown, no compatibility list available bit3 not used bit4 Passive bank download possible (far NE compatible) bit5 Passive bank download not possible (far NE offline or not compatible) bit6 Passive bank unknown, no compatibility list available bit7 unsupported variable for addressed device | ||||
| CdownloadRemDwlPossibleReg3Wp2 | 1.3.6.1.4.1.1887.1.1.4.3.7.5.1.14 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a remote download is possible or not. The value is bit-coded: bit0 Active bank download possible (far NE compatible) bit1 Active bank download not possible (far NE offline or not compatible) bit2 Active bank unknown, no compatibility list available bit3 not used bit4 Passive bank download possible (far NE compatible) bit5 Passive bank download not possible (far NE offline or not compatible) bit6 Passive bank unknown, no compatibility list available bit7 unsupported variable for addressed device | ||||
| CdownloadRemDwlPossibleReg4Wp2 | 1.3.6.1.4.1.1887.1.1.4.3.7.5.1.15 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a remote download is possible or not. The value is bit-coded: bit0 Active bank download possible (far NE compatible) bit1 Active bank download not possible (far NE offline or not compatible) bit2 Active bank unknown, no compatibility list available bit3 not used bit4 Passive bank download possible (far NE compatible) bit5 Passive bank download not possible (far NE offline or not compatible) bit6 Passive bank unknown, no compatibility list available bit7 unsupported variable for addressed device | ||||
| CdownloadRemDwlPossibleReg5Wp2 | 1.3.6.1.4.1.1887.1.1.4.3.7.5.1.16 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a remote download is possible or not. The value is bit-coded: bit0 Active bank download possible (far NE compatible) bit1 Active bank download not possible (far NE offline or not compatible) bit2 Active bank unknown, no compatibility list available bit3 not used bit4 Passive bank download possible (far NE compatible) bit5 Passive bank download not possible (far NE offline or not compatible) bit6 Passive bank unknown, no compatibility list available bit7 unsupported variable for addressed device | ||||
| CdownloadRemDwlPossibleReg6Wp2 | 1.3.6.1.4.1.1887.1.1.4.3.7.5.1.17 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a remote download is possible or not. The value is bit-coded: bit0 Active bank download possible (far NE compatible) bit1 Active bank download not possible (far NE offline or not compatible) bit2 Active bank unknown, no compatibility list available bit3 not used bit4 Passive bank download possible (far NE compatible) bit5 Passive bank download not possible (far NE offline or not compatible) bit6 Passive bank unknown, no compatibility list available bit7 unsupported variable for addressed device | ||||
| CdownloadRemDwlPossibleReg7Wp2 | 1.3.6.1.4.1.1887.1.1.4.3.7.5.1.18 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a remote download is possible or not. The value is bit-coded: bit0 Active bank download possible (far NE compatible) bit1 Active bank download not possible (far NE offline or not compatible) bit2 Active bank unknown, no compatibility list available bit3 not used bit4 Passive bank download possible (far NE compatible) bit5 Passive bank download not possible (far NE offline or not compatible) bit6 Passive bank unknown, no compatibility list available bit7 unsupported variable for addressed device | ||||
| CdownloadRemDwlPossibleReg8Wp2 | 1.3.6.1.4.1.1887.1.1.4.3.7.5.1.19 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a remote download is possible or not. The value is bit-coded: bit0 Active bank download possible (far NE compatible) bit1 Active bank download not possible (far NE offline or not compatible) bit2 Active bank unknown, no compatibility list available bit3 not used bit4 Passive bank download possible (far NE compatible) bit5 Passive bank download not possible (far NE offline or not compatible) bit6 Passive bank unknown, no compatibility list available bit7 unsupported variable for addressed device | ||||
| CdownloadRemDwlPossibleReg1Wp3 | 1.3.6.1.4.1.1887.1.1.4.3.7.5.1.20 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a remote download is possible or not. The value is bit-coded: bit0 Active bank download possible (far NE compatible) bit1 Active bank download not possible (far NE offline or not compatible) bit2 Active bank unknown, no compatibility list available bit3 not used bit4 Passive bank download possible (far NE compatible) bit5 Passive bank download not possible (far NE offline or not compatible) bit6 Passive bank unknown, no compatibility list available bit7 unsupported variable for addressed device | ||||
| CdownloadRemDwlPossibleReg2Wp3 | 1.3.6.1.4.1.1887.1.1.4.3.7.5.1.21 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a remote download is possible or not. The value is bit-coded: bit0 Active bank download possible (far NE compatible) bit1 Active bank download not possible (far NE offline or not compatible) bit2 Active bank unknown, no compatibility list available bit3 not used bit4 Passive bank download possible (far NE compatible) bit5 Passive bank download not possible (far NE offline or not compatible) bit6 Passive bank unknown, no compatibility list available bit7 unsupported variable for addressed device | ||||
| CdownloadRemDwlPossibleReg3Wp3 | 1.3.6.1.4.1.1887.1.1.4.3.7.5.1.22 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a remote download is possible or not. The value is bit-coded: bit0 Active bank download possible (far NE compatible) bit1 Active bank download not possible (far NE offline or not compatible) bit2 Active bank unknown, no compatibility list available bit3 not used bit4 Passive bank download possible (far NE compatible) bit5 Passive bank download not possible (far NE offline or not compatible) bit6 Passive bank unknown, no compatibility list available bit7 unsupported variable for addressed device | ||||
| CdownloadRemDwlPossibleReg4Wp3 | 1.3.6.1.4.1.1887.1.1.4.3.7.5.1.23 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a remote download is possible or not. The value is bit-coded: bit0 Active bank download possible (far NE compatible) bit1 Active bank download not possible (far NE offline or not compatible) bit2 Active bank unknown, no compatibility list available bit3 not used bit4 Passive bank download possible (far NE compatible) bit5 Passive bank download not possible (far NE offline or not compatible) bit6 Passive bank unknown, no compatibility list available bit7 unsupported variable for addressed device | ||||
| CdownloadRemDwlPossibleReg5Wp3 | 1.3.6.1.4.1.1887.1.1.4.3.7.5.1.24 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a remote download is possible or not. The value is bit-coded: bit0 Active bank download possible (far NE compatible) bit1 Active bank download not possible (far NE offline or not compatible) bit2 Active bank unknown, no compatibility list available bit3 not used bit4 Passive bank download possible (far NE compatible) bit5 Passive bank download not possible (far NE offline or not compatible) bit6 Passive bank unknown, no compatibility list available bit7 unsupported variable for addressed device | ||||
| CdownloadRemDwlPossibleReg6Wp3 | 1.3.6.1.4.1.1887.1.1.4.3.7.5.1.25 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a remote download is possible or not. The value is bit-coded: bit0 Active bank download possible (far NE compatible) bit1 Active bank download not possible (far NE offline or not compatible) bit2 Active bank unknown, no compatibility list available bit3 not used bit4 Passive bank download possible (far NE compatible) bit5 Passive bank download not possible (far NE offline or not compatible) bit6 Passive bank unknown, no compatibility list available bit7 unsupported variable for addressed device | ||||
| CdownloadRemDwlPossibleReg7Wp3 | 1.3.6.1.4.1.1887.1.1.4.3.7.5.1.26 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a remote download is possible or not. The value is bit-coded: bit0 Active bank download possible (far NE compatible) bit1 Active bank download not possible (far NE offline or not compatible) bit2 Active bank unknown, no compatibility list available bit3 not used bit4 Passive bank download possible (far NE compatible) bit5 Passive bank download not possible (far NE offline or not compatible) bit6 Passive bank unknown, no compatibility list available bit7 unsupported variable for addressed device | ||||
| CdownloadRemDwlPossibleReg8Wp3 | 1.3.6.1.4.1.1887.1.1.4.3.7.5.1.27 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a remote download is possible or not. The value is bit-coded: bit0 Active bank download possible (far NE compatible) bit1 Active bank download not possible (far NE offline or not compatible) bit2 Active bank unknown, no compatibility list available bit3 not used bit4 Passive bank download possible (far NE compatible) bit5 Passive bank download not possible (far NE offline or not compatible) bit6 Passive bank unknown, no compatibility list available bit7 unsupported variable for addressed device | ||||
| CdownloadRemDwlPossibleReg1Wp4 | 1.3.6.1.4.1.1887.1.1.4.3.7.5.1.28 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a remote download is possible or not. The value is bit-coded: bit0 Active bank download possible (far NE compatible) bit1 Active bank download not possible (far NE offline or not compatible) bit2 Active bank unknown, no compatibility list available bit3 not used bit4 Passive bank download possible (far NE compatible) bit5 Passive bank download not possible (far NE offline or not compatible) bit6 Passive bank unknown, no compatibility list available bit7 unsupported variable for addressed device | ||||
| CdownloadRemDwlPossibleReg2Wp4 | 1.3.6.1.4.1.1887.1.1.4.3.7.5.1.29 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a remote download is possible or not. The value is bit-coded: bit0 Active bank download possible (far NE compatible) bit1 Active bank download not possible (far NE offline or not compatible) bit2 Active bank unknown, no compatibility list available bit3 not used bit4 Passive bank download possible (far NE compatible) bit5 Passive bank download not possible (far NE offline or not compatible) bit6 Passive bank unknown, no compatibility list available bit7 unsupported variable for addressed device | ||||
| CdownloadRemDwlPossibleReg3Wp4 | 1.3.6.1.4.1.1887.1.1.4.3.7.5.1.30 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a remote download is possible or not. The value is bit-coded: bit0 Active bank download possible (far NE compatible) bit1 Active bank download not possible (far NE offline or not compatible) bit2 Active bank unknown, no compatibility list available bit3 not used bit4 Passive bank download possible (far NE compatible) bit5 Passive bank download not possible (far NE offline or not compatible) bit6 Passive bank unknown, no compatibility list available bit7 unsupported variable for addressed device | ||||
| CdownloadRemDwlPossibleReg4Wp4 | 1.3.6.1.4.1.1887.1.1.4.3.7.5.1.31 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a remote download is possible or not. The value is bit-coded: bit0 Active bank download possible (far NE compatible) bit1 Active bank download not possible (far NE offline or not compatible) bit2 Active bank unknown, no compatibility list available bit3 not used bit4 Passive bank download possible (far NE compatible) bit5 Passive bank download not possible (far NE offline or not compatible) bit6 Passive bank unknown, no compatibility list available bit7 unsupported variable for addressed device | ||||
| CdownloadRemDwlPossibleReg5Wp4 | 1.3.6.1.4.1.1887.1.1.4.3.7.5.1.32 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a remote download is possible or not. The value is bit-coded: bit0 Active bank download possible (far NE compatible) bit1 Active bank download not possible (far NE offline or not compatible) bit2 Active bank unknown, no compatibility list available bit3 not used bit4 Passive bank download possible (far NE compatible) bit5 Passive bank download not possible (far NE offline or not compatible) bit6 Passive bank unknown, no compatibility list available bit7 unsupported variable for addressed device | ||||
| CdownloadRemDwlPossibleReg6Wp4 | 1.3.6.1.4.1.1887.1.1.4.3.7.5.1.33 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a remote download is possible or not. The value is bit-coded: bit0 Active bank download possible (far NE compatible) bit1 Active bank download not possible (far NE offline or not compatible) bit2 Active bank unknown, no compatibility list available bit3 not used bit4 Passive bank download possible (far NE compatible) bit5 Passive bank download not possible (far NE offline or not compatible) bit6 Passive bank unknown, no compatibility list available bit7 unsupported variable for addressed device | ||||
| CdownloadRemDwlPossibleReg7Wp4 | 1.3.6.1.4.1.1887.1.1.4.3.7.5.1.34 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a remote download is possible or not. The value is bit-coded: bit0 Active bank download possible (far NE compatible) bit1 Active bank download not possible (far NE offline or not compatible) bit2 Active bank unknown, no compatibility list available bit3 not used bit4 Passive bank download possible (far NE compatible) bit5 Passive bank download not possible (far NE offline or not compatible) bit6 Passive bank unknown, no compatibility list available bit7 unsupported variable for addressed device | ||||
| CdownloadRemDwlPossibleReg8Wp4 | 1.3.6.1.4.1.1887.1.1.4.3.7.5.1.35 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a remote download is possible or not. The value is bit-coded: bit0 Active bank download possible (far NE compatible) bit1 Active bank download not possible (far NE offline or not compatible) bit2 Active bank unknown, no compatibility list available bit3 not used bit4 Passive bank download possible (far NE compatible) bit5 Passive bank download not possible (far NE offline or not compatible) bit6 Passive bank unknown, no compatibility list available bit7 unsupported variable for addressed device | ||||
| TdownloadSwapPossibleTable | 1.3.6.1.4.1.1887.1.1.4.3.7.6 | NA | mandatory | |
| RdownloadSwapPossibleEntry | 1.3.6.1.4.1.1887.1.1.4.3.7.6.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CdownloadSwapPossiblePortIndex | 1.3.6.1.4.1.1887.1.1.4.3.7.6.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CdownloadSwapPossibleLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.7.6.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CdownloadSwapPossibleLocal | 1.3.6.1.4.1.1887.1.1.4.3.7.6.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a firmware bank swap is possible or not. 1 SwapNotPossible Bank swap is not possible 2 SwapPossible Bank swap is possible 254 unknown value 255 unsupported variable for addressed device
| ||||
| CdownloadSwapPossibleNt | 1.3.6.1.4.1.1887.1.1.4.3.7.6.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a firmware bank swap is possible or not. 1 SwapNotPossible Bank swap is not possible 2 SwapPossible Bank swap is possible 254 unknown value 255 unsupported variable for addressed device
| ||||
| CdownloadSwapPossibleReg1Wp1 | 1.3.6.1.4.1.1887.1.1.4.3.7.6.1.5 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a firmware bank swap is possible or not. 1 SwapNotPossible Bank swap is not possible 2 SwapPossible Bank swap is possible 254 unknown value 255 unsupported variable for addressed device
| ||||
| CdownloadSwapPossibleReg2Wp1 | 1.3.6.1.4.1.1887.1.1.4.3.7.6.1.6 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a firmware bank swap is possible or not. 1 SwapNotPossible Bank swap is not possible 2 SwapPossible Bank swap is possible 254 unknown value 255 unsupported variable for addressed device
| ||||
| CdownloadSwapPossibleReg3Wp1 | 1.3.6.1.4.1.1887.1.1.4.3.7.6.1.7 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a firmware bank swap is possible or not. 1 SwapNotPossible Bank swap is not possible 2 SwapPossible Bank swap is possible 254 unknown value 255 unsupported variable for addressed device
| ||||
| CdownloadSwapPossibleReg4Wp1 | 1.3.6.1.4.1.1887.1.1.4.3.7.6.1.8 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a firmware bank swap is possible or not. 1 SwapNotPossible Bank swap is not possible 2 SwapPossible Bank swap is possible 254 unknown value 255 unsupported variable for addressed device
| ||||
| CdownloadSwapPossibleReg5Wp1 | 1.3.6.1.4.1.1887.1.1.4.3.7.6.1.9 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a firmware bank swap is possible or not. 1 SwapNotPossible Bank swap is not possible 2 SwapPossible Bank swap is possible 254 unknown value 255 unsupported variable for addressed device
| ||||
| CdownloadSwapPossibleReg6Wp1 | 1.3.6.1.4.1.1887.1.1.4.3.7.6.1.10 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a firmware bank swap is possible or not. 1 SwapNotPossible Bank swap is not possible 2 SwapPossible Bank swap is possible 254 unknown value 255 unsupported variable for addressed device
| ||||
| CdownloadSwapPossibleReg7Wp1 | 1.3.6.1.4.1.1887.1.1.4.3.7.6.1.11 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a firmware bank swap is possible or not. 1 SwapNotPossible Bank swap is not possible 2 SwapPossible Bank swap is possible 254 unknown value 255 unsupported variable for addressed device
| ||||
| CdownloadSwapPossibleReg8Wp1 | 1.3.6.1.4.1.1887.1.1.4.3.7.6.1.12 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a firmware bank swap is possible or not. 1 SwapNotPossible Bank swap is not possible 2 SwapPossible Bank swap is possible 254 unknown value 255 unsupported variable for addressed device
| ||||
| CdownloadSwapPossibleReg1Wp2 | 1.3.6.1.4.1.1887.1.1.4.3.7.6.1.13 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a firmware bank swap is possible or not. 1 SwapNotPossible Bank swap is not possible 2 SwapPossible Bank swap is possible 254 unknown value 255 unsupported variable for addressed device
| ||||
| CdownloadSwapPossibleReg2Wp2 | 1.3.6.1.4.1.1887.1.1.4.3.7.6.1.14 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a firmware bank swap is possible or not. 1 SwapNotPossible Bank swap is not possible 2 SwapPossible Bank swap is possible 254 unknown value 255 unsupported variable for addressed device
| ||||
| CdownloadSwapPossibleReg3Wp2 | 1.3.6.1.4.1.1887.1.1.4.3.7.6.1.15 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a firmware bank swap is possible or not. 1 SwapNotPossible Bank swap is not possible 2 SwapPossible Bank swap is possible 254 unknown value 255 unsupported variable for addressed device
| ||||
| CdownloadSwapPossibleReg4Wp2 | 1.3.6.1.4.1.1887.1.1.4.3.7.6.1.16 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a firmware bank swap is possible or not. 1 SwapNotPossible Bank swap is not possible 2 SwapPossible Bank swap is possible 254 unknown value 255 unsupported variable for addressed device
| ||||
| CdownloadSwapPossibleReg5Wp2 | 1.3.6.1.4.1.1887.1.1.4.3.7.6.1.17 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a firmware bank swap is possible or not. 1 SwapNotPossible Bank swap is not possible 2 SwapPossible Bank swap is possible 254 unknown value 255 unsupported variable for addressed device
| ||||
| CdownloadSwapPossibleReg6Wp2 | 1.3.6.1.4.1.1887.1.1.4.3.7.6.1.18 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a firmware bank swap is possible or not. 1 SwapNotPossible Bank swap is not possible 2 SwapPossible Bank swap is possible 254 unknown value 255 unsupported variable for addressed device
| ||||
| CdownloadSwapPossibleReg7Wp2 | 1.3.6.1.4.1.1887.1.1.4.3.7.6.1.19 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a firmware bank swap is possible or not. 1 SwapNotPossible Bank swap is not possible 2 SwapPossible Bank swap is possible 254 unknown value 255 unsupported variable for addressed device
| ||||
| CdownloadSwapPossibleReg8Wp2 | 1.3.6.1.4.1.1887.1.1.4.3.7.6.1.20 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a firmware bank swap is possible or not. 1 SwapNotPossible Bank swap is not possible 2 SwapPossible Bank swap is possible 254 unknown value 255 unsupported variable for addressed device
| ||||
| CdownloadSwapPossibleReg1Wp3 | 1.3.6.1.4.1.1887.1.1.4.3.7.6.1.21 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a firmware bank swap is possible or not. 1 SwapNotPossible Bank swap is not possible 2 SwapPossible Bank swap is possible 254 unknown value 255 unsupported variable for addressed device
| ||||
| CdownloadSwapPossibleReg2Wp3 | 1.3.6.1.4.1.1887.1.1.4.3.7.6.1.22 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a firmware bank swap is possible or not. 1 SwapNotPossible Bank swap is not possible 2 SwapPossible Bank swap is possible 254 unknown value 255 unsupported variable for addressed device
| ||||
| CdownloadSwapPossibleReg3Wp3 | 1.3.6.1.4.1.1887.1.1.4.3.7.6.1.23 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a firmware bank swap is possible or not. 1 SwapNotPossible Bank swap is not possible 2 SwapPossible Bank swap is possible 254 unknown value 255 unsupported variable for addressed device
| ||||
| CdownloadSwapPossibleReg4Wp3 | 1.3.6.1.4.1.1887.1.1.4.3.7.6.1.24 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a firmware bank swap is possible or not. 1 SwapNotPossible Bank swap is not possible 2 SwapPossible Bank swap is possible 254 unknown value 255 unsupported variable for addressed device
| ||||
| CdownloadSwapPossibleReg5Wp3 | 1.3.6.1.4.1.1887.1.1.4.3.7.6.1.25 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a firmware bank swap is possible or not. 1 SwapNotPossible Bank swap is not possible 2 SwapPossible Bank swap is possible 254 unknown value 255 unsupported variable for addressed device
| ||||
| CdownloadSwapPossibleReg6Wp3 | 1.3.6.1.4.1.1887.1.1.4.3.7.6.1.26 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a firmware bank swap is possible or not. 1 SwapNotPossible Bank swap is not possible 2 SwapPossible Bank swap is possible 254 unknown value 255 unsupported variable for addressed device
| ||||
| CdownloadSwapPossibleReg7Wp3 | 1.3.6.1.4.1.1887.1.1.4.3.7.6.1.27 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a firmware bank swap is possible or not. 1 SwapNotPossible Bank swap is not possible 2 SwapPossible Bank swap is possible 254 unknown value 255 unsupported variable for addressed device
| ||||
| CdownloadSwapPossibleReg8Wp3 | 1.3.6.1.4.1.1887.1.1.4.3.7.6.1.28 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a firmware bank swap is possible or not. 1 SwapNotPossible Bank swap is not possible 2 SwapPossible Bank swap is possible 254 unknown value 255 unsupported variable for addressed device
| ||||
| CdownloadSwapPossibleReg1Wp4 | 1.3.6.1.4.1.1887.1.1.4.3.7.6.1.29 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a firmware bank swap is possible or not. 1 SwapNotPossible Bank swap is not possible 2 SwapPossible Bank swap is possible 254 unknown value 255 unsupported variable for addressed device
| ||||
| CdownloadSwapPossibleReg2Wp4 | 1.3.6.1.4.1.1887.1.1.4.3.7.6.1.30 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a firmware bank swap is possible or not. 1 SwapNotPossible Bank swap is not possible 2 SwapPossible Bank swap is possible 254 unknown value 255 unsupported variable for addressed device
| ||||
| CdownloadSwapPossibleReg3Wp4 | 1.3.6.1.4.1.1887.1.1.4.3.7.6.1.31 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a firmware bank swap is possible or not. 1 SwapNotPossible Bank swap is not possible 2 SwapPossible Bank swap is possible 254 unknown value 255 unsupported variable for addressed device
| ||||
| CdownloadSwapPossibleReg4Wp4 | 1.3.6.1.4.1.1887.1.1.4.3.7.6.1.32 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a firmware bank swap is possible or not. 1 SwapNotPossible Bank swap is not possible 2 SwapPossible Bank swap is possible 254 unknown value 255 unsupported variable for addressed device
| ||||
| CdownloadSwapPossibleReg5Wp4 | 1.3.6.1.4.1.1887.1.1.4.3.7.6.1.33 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a firmware bank swap is possible or not. 1 SwapNotPossible Bank swap is not possible 2 SwapPossible Bank swap is possible 254 unknown value 255 unsupported variable for addressed device
| ||||
| CdownloadSwapPossibleReg6Wp4 | 1.3.6.1.4.1.1887.1.1.4.3.7.6.1.34 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a firmware bank swap is possible or not. 1 SwapNotPossible Bank swap is not possible 2 SwapPossible Bank swap is possible 254 unknown value 255 unsupported variable for addressed device
| ||||
| CdownloadSwapPossibleReg7Wp4 | 1.3.6.1.4.1.1887.1.1.4.3.7.6.1.35 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a firmware bank swap is possible or not. 1 SwapNotPossible Bank swap is not possible 2 SwapPossible Bank swap is possible 254 unknown value 255 unsupported variable for addressed device
| ||||
| CdownloadSwapPossibleReg8Wp4 | 1.3.6.1.4.1.1887.1.1.4.3.7.6.1.36 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether a firmware bank swap is possible or not. 1 SwapNotPossible Bank swap is not possible 2 SwapPossible Bank swap is possible 254 unknown value 255 unsupported variable for addressed device
| ||||
| NextendedTraps | 1.3.6.1.4.1.1887.1.1.4.3.8 | |||
| TextendedTrapsTable | 1.3.6.1.4.1.1887.1.1.4.3.8.1 | NA | mandatory | |
| RextendedTrapsEntry | 1.3.6.1.4.1.1887.1.1.4.3.8.1.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CextendedTrapsPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.8.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| CextendedTrapsLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.8.1.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| CextendedTrapsType | 1.3.6.1.4.1.1887.1.1.4.3.8.1.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable is only used as an attachement on the extended snmp trap 1 LineConfigChange The line configuration has changed 2 AlarmConfigChange The alarm configuration has changed 3 RDWLState The state of the remote download has changed 4 RebootRemote The remote device has rebooted 5 LDWLState The state of the local download has changed 6 LineProbing The lineprobing is terminated 7 UserDataChange The user data string has changed 8 LEDStateChange The LED state has changed 9 SystemConfigChange The number of wire pairs has changed 10 TEDataAvailable Terminal emulation offers data for terminal output 11 TESessionEnd End of terminal session on line card (not OMII) 12 TEPwrStationAlCfg Change of Power Station Alarms (to OMII) 13 PwdLost Password lost 14 Link FE or GbE link status changed 15 Authentication Authentication status changed 16 MultipleUsers Multiple users status changed 17 STP Spanning Tree Protocol status changed 18 ACL Access Control Lists status changed 19 CfgChangeL2Switch L2 Switch configuration data changed 254 unknown value 255 unsupported variable for addressed device
| ||||
| Nsmrw | 1.3.6.1.4.1.1887.1.1.4.3.9 | |||
| TsmrwOmiTable | 1.3.6.1.4.1.1887.1.1.4.3.9.1 | NA | mandatory | |
| RsmrwOmiEntry | 1.3.6.1.4.1.1887.1.1.4.3.9.1.1 | NA | mandatory | |
row · not-accessible · mandatory
| ||||
| CsmrwOmiPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.9.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable is used as index for the other elements in the Table | ||||
| CsmrwOmiLCTLocalMgmt | 1.3.6.1.4.1.1887.1.1.4.3.9.1.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This is a read-only variable which is used to get LCT local management status: 1 NO_ACCESS 2 RO_ACCESS 3 RW_ACCESS 254 unknown value 255 unsupported value
| ||||
| CsmrwOmiLCTRemoteMgmt | 1.3.6.1.4.1.1887.1.1.4.3.9.1.1.3 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory This is a read-write variable which is used to get/set LCT remote management status: 1 NO_ACCESS 2 RO_ACCESS 3 RW_ACCESS 254 unknown value 255 unsupported value
| ||||
| CsmrwOmiSNMPv1-v2Mgmt | 1.3.6.1.4.1.1887.1.1.4.3.9.1.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory This is a read-write variable which is used to get/set SNMPv1 and SNMPv2 management status: 1 NO_ACCESS 2 RO_ACCESS 3 RW_ACCESS 254 unknown value 255 unsupported value
| ||||
| CsmrwOmiSNMPv3Mgmt | 1.3.6.1.4.1.1887.1.1.4.3.9.1.1.5 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory This is a read-write variable which is used to get/set SNMPv3 management status: 1 NO_ACCESS 2 RO_ACCESS 3 RW_ACCESS 254 unknown value 255 unsupported value
| ||||
| CsmrwOmiCLIMgmt | 1.3.6.1.4.1.1887.1.1.4.3.9.1.1.6 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory This is a read-write variable which is used to get/set CLI management status: 1 NO_ACCESS 2 RO_ACCESS 3 RW_ACCESS 254 unknown value 255 unsupported value
| ||||
| CsmrwOmiWebMgmt | 1.3.6.1.4.1.1887.1.1.4.3.9.1.1.7 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This is a read-only variable which is used to get Web management status: 1 NO_ACCESS 2 RO_ACCESS 3 RW_ACCESS 254 unknown value 255 unsupported value
| ||||
| NomppOverSNMP | 1.3.6.1.4.1.1887.1.1.4.3.10 | |||
| TomppOverSNMPTable | 1.3.6.1.4.1.1887.1.1.4.3.10.1 | NA | mandatory | |
| RomppOverSNMPEntry | 1.3.6.1.4.1.1887.1.1.4.3.10.1.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| ComppOverSNMPPortIndex | 1.3.6.1.4.1.1887.1.1.4.3.10.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the port number of the proxy and is used as index for the other elements in the Table | ||||
| ComppOverSNMPLinkIndex | 1.3.6.1.4.1.1887.1.1.4.3.10.1.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This variable addresses the slot number of the OMI sub-rack and is used as index for the other elements in the Table | ||||
| ComppOverSNMPInvokeInfo | 1.3.6.1.4.1.1887.1.1.4.3.10.1.1.3 | OCTET STRING (SIZE (1..255)) | RO | mandatory |
column · OCTET STRING (SIZE (1..255)) · read-only · mandatory OMPP Invoke Telegram Data (only L7) | ||||
| ComppOverSNMPGetData | 1.3.6.1.4.1.1887.1.1.4.3.10.1.1.4 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Confirm Telegram Data (Get,read) | ||||
| ComppOverSNMPSetData | 1.3.6.1.4.1.1887.1.1.4.3.10.1.1.5 | OCTET STRING | RW | mandatory |
column · OCTET STRING · read-write · mandatory Additional OMPP Invoke Telegram Data (Set, write) | ||||