NETGEAR-VPC-MIB
Broadcom LimitedThe MIB definitions VPC Feature.
snmptranslate -m NETGEAR-VPC-MIB -Tpsnmpwalk -v2c -c <community> -m NETGEAR-VPC-MIB <host> 1.3.6.1.4.1.4413.1.1.200Imports
| IF-MIB | InterfaceIndex |
|---|---|
| QUANTA-LB6M-REF-MIB | AgentPortMask, lb6m |
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP |
| SNMPv2-SMI | Bits, Integer32, IpAddress, MODULE-IDENTITY, MibIdentifier, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, iso |
| SNMPv2-TC | DisplayString, MacAddress, PhysAddress, RowStatus, TEXTUAL-CONVENTION, TruthValue |
OID tree
| Name | OID | Type | Access | Status |
|---|---|---|---|---|
| IfastPathVpc | 1.3.6.1.4.1.4413.1.1.200 | |||
identity The MIB definitions VPC Feature. | ||||
| NagentVpcConfigGroup | 1.3.6.1.4.1.4413.1.1.200.1 | |||
| SagentVpcMode | 1.3.6.1.4.1.4413.1.1.200.1.1 | INTEGER | RW | |
scalar · INTEGER · read-write · current To enable VPC globally. The VPC role election happens if both the VPC feature is enabled and if the keepalive state machine is enabled. The following options are supported: enable - Enable VPC globally disable - Disable VPC globally
| ||||
| SagentKeepalivePriority | 1.3.6.1.4.1.4413.1.1.200.1.2 | Unsigned32 (1..255) | RW | obsolete |
scalar · Unsigned32 (1..255) · read-write · obsolete To configure the priority of the VPC switch. This value is used
for the VPC role election.
Configurable range is 1 to 255. The default value is 100.
Note: The VPC switch with lower priority becomes the Primary. If
both the VPC peer switches have the same role priority, the
device with lower system MAC address becomes the Primary. | ||||
| SagentKeepaliveTimeout | 1.3.6.1.4.1.4413.1.1.200.1.3 | Unsigned32 (2..15) | RW | obsolete |
scalar · Unsigned32 (2..15) · read-write · obsolete To configure the peer keepalive timeout value (in seconds). If an VPC switch does not receive keepalive messages from the peer for this timeout value, it takes the decision to transition its role (if required). Configurable rang is 2 to 15 seconds. Default value is 5 seconds. Note: The keepalive state machine is not restarted if keepalive priority is modified post election. | ||||
| SagentKeepaliveMode | 1.3.6.1.4.1.4413.1.1.200.1.4 | INTEGER | RW | obsolete |
scalar · INTEGER · read-write · obsolete To start/stop the keepalive state machine on the VPC device, if VPC is globally enabled. The following options are supported: enable - Enable keepalive disable - Disable keepalive
| ||||
| SagentPeerLink | 1.3.6.1.4.1.4413.1.1.200.1.5 | InterfaceIndex | RW | |
scalar · InterfaceIndex · read-write · current To configures a port channel as the VPC peer link. The configurable range is a valid port channel interface index. | ||||
| SagentPeerDetectionMode | 1.3.6.1.4.1.4413.1.1.200.1.6 | INTEGER | RW | obsolete |
scalar · INTEGER · read-write · obsolete To start/stop the dual control plane detection protocol (DCPDP) on the
VPC switch.
The following options are supported:
enable - Enable the DCPDP on VPC switch
disable - Disable the DCPDP on VPC switch
Note: The peer VPC switch's IP address has to be configured for
the DCPDP to start on an VPC switch.
| ||||
| TagentVpcConfigTable | 1.3.6.1.4.1.4413.1.1.200.1.7 | NA | obsolete | |
table · not-accessible · obsolete VPC config table. | ||||
| RagentVpcConfigEntry | 1.3.6.1.4.1.4413.1.1.200.1.7.1 | NA | obsolete | |
| CagentVpcConfigId | 1.3.6.1.4.1.4413.1.1.200.1.7.1.1 | Unsigned32 (1..63) | RO | obsolete |
column · Unsigned32 (1..63) · read-only · obsolete VPC Id. This object is obselete. Refer to agentVpcDomainIndex for configuring VPC Id. | ||||
| CagentVpcTrackPortMask | 1.3.6.1.4.1.4413.1.1.200.1.7.1.2 | AgentPortMask | RW | obsolete |
column · AgentPortMask · read-write · obsolete Tracking of non-mlag links. | ||||
| TagentPeerConfigTable | 1.3.6.1.4.1.4413.1.1.200.1.8 | NA | obsolete | |
table · not-accessible · obsolete VPC config table. | ||||
| RagentPeerConfigEntry | 1.3.6.1.4.1.4413.1.1.200.1.8.1 | NA | obsolete | |
| CagentPeerConfigRowIndex | 1.3.6.1.4.1.4413.1.1.200.1.8.1.1 | Unsigned32 (1) | NA | obsolete |
column · Unsigned32 (1) · not-accessible · obsolete Index. | ||||
| CagentPeerIpAddr | 1.3.6.1.4.1.4413.1.1.200.1.8.1.2 | IpAddress | RW | obsolete |
column · IpAddress · read-write · obsolete To configure IP address of the peer VPC switch. This configuration is used by the dual control plane detection protocol (DCPDP) on the VPC switches. NOTE: In order to set value for the object, need to set values for agentPeerIpAddr, agentSourceIpAddr, agentPeerRowStatus objects simultaneously. To reset the object to the default state, the agentPeerRowStatus object should be used. | ||||
| CagentSourceIpAddr | 1.3.6.1.4.1.4413.1.1.200.1.8.1.3 | IpAddress | RW | obsolete |
column · IpAddress · read-write · obsolete To configure Self IP address of the VPC switch that is used as the source IP by the dual control plane detection protocol (DCPDP) on the VPC switches. NOTE: In order to set value for the object, need to set values for agentPeerIpAddr, agentSourceIpAddr, agentPeerRowStatus objects simultaneously. To reset the object to the default state, the agentPeerRowStatus object should be used. | ||||
| CagentDcpdpUdpPort | 1.3.6.1.4.1.4413.1.1.200.1.8.1.4 | Unsigned32 (1..65535) | RW | obsolete |
column · Unsigned32 (1..65535) · read-write · obsolete To configure the UDP port on which the VPC switch listens to the DCPDP messages. Configurable range is 1 to 65535. Default value is 50000. NOTE: In order to set value for the object, need to set values for agentPeerIpAddr, agentSourceIpAddr, agentPeerRowStatus, agentDcpdpUdpPort objects simultaneously. To reset the object to the default state, the agentPeerRowStatus object should be used. | ||||
| CagentPeerRowStatus | 1.3.6.1.4.1.4413.1.1.200.1.8.1.5 | RowStatus | RC | obsolete |
column · RowStatus · read-create · obsolete Peer config status. Supported values: active(1) - valid instance. createAndGo(4) - used to configure peer configuration. destroy(6) - reset peer configuration. | ||||
| TagentVpcDomainConfigTable | 1.3.6.1.4.1.4413.1.1.200.1.9 | NA | ||
table · not-accessible · current VPC domain config table. | ||||
| RagentVpcDomainConfigEntry | 1.3.6.1.4.1.4413.1.1.200.1.9.1 | NA | ||
| CagentVpcDomainIndex | 1.3.6.1.4.1.4413.1.1.200.1.9.1.1 | Unsigned32 (1..255) | RW | |
column · Unsigned32 (1..255) · read-write · current VPC Domain ID. | ||||
| CagentVpcDomainKeepalivePriority | 1.3.6.1.4.1.4413.1.1.200.1.9.1.2 | Unsigned32 (1..255) | RW | |
column · Unsigned32 (1..255) · read-write · current To configure the priority of the VPC switch. This value is used
for the VPC role election.
Configurable range is 1 to 255. The default value is 100.
Note: The VPC switch with lower priority becomes the Primary. If
both the VPC peer switches have the same role priority, the
device with lower system MAC address becomes the Primary. | ||||
| CagentVpcDomainKeepaliveTimeout | 1.3.6.1.4.1.4413.1.1.200.1.9.1.3 | Unsigned32 (2..15) | RW | |
column · Unsigned32 (2..15) · read-write · current To configure the peer keepalive timeout value (in seconds). If an VPC switch does not receive keepalive messages from the peer for this timeout value, it takes the decision to transition its role (if required). Configurable range is 2 to 15 seconds. Default value is 5 seconds. Note: The keepalive state machine is not restarted if keepalive priority is modified post election. | ||||
| CagentVpcDomainKeepaliveMode | 1.3.6.1.4.1.4413.1.1.200.1.9.1.4 | INTEGER | RW | |
column · INTEGER · read-write · current To start/stop the keepalive state machine on the VPC device, if VPC is globally enabled. The following options are supported: enable - Enable keepalive disable - Disable keepalive
| ||||
| CagentVpcDomainPeerDetectionMode | 1.3.6.1.4.1.4413.1.1.200.1.9.1.5 | INTEGER | RW | |
column · INTEGER · read-write · current To start/stop the dual control plane detection protocol (DCPDP) on the
VPC switch.
The following options are supported:
enable - Enable the DCPDP on VPC switch
disable - Disable the DCPDP on VPC switch
Note: The peer VPC switch's IP address has to be configured for
the DCPDP to start on an VPC switch.
| ||||
| CagentVpcDomainSystemMac | 1.3.6.1.4.1.4413.1.1.200.1.9.1.6 | MacAddress | RW | |
column · MacAddress · read-write · current To configure the MAC address for the VPC domain. This mac-address is used in the LACP PDUs and STP BPDUs that are sent out on VPC member ports. For the VPC domain to use the manually configured VPC MAC address, it should be manually configured on both the VPC peers and should be the same. If VPC is configured on only one of the VPC peers or is configured different on VPC peers, auto-generated MAC address is used. The specified MAC address should be a unicast MAC address in <aa:bb:cc:dd:ee:ff> format and should not be equal to the MAC address of either primary VPC or secondary VPC device. The manually configured VPC MAC address is used instead of auto-generated VPC MAC address only if the VPC feature is re-enabled after configuring the VPC MAC address. | ||||
| CagentVpcDomainSystemPriority | 1.3.6.1.4.1.4413.1.1.200.1.9.1.7 | Unsigned32 (1..65535) | RW | |
column · Unsigned32 (1..65535) · read-write · current To configure the system priority for the VPC domain. This is used in the LACP PDUs sent out on VPC member ports. System-priority should be configured same on both the VPC peers. If the configured VPC system priority is different on VPC peers, then VPC will not come up. The default priority value is 32767. | ||||
| CagentVpcDomainPeerDetectionInterval | 1.3.6.1.4.1.4413.1.1.200.1.9.1.8 | Unsigned32 (200..4000) | RW | |
column · Unsigned32 (200..4000) · read-write · current To configure the DCPDP transmission interval. NOTE: In order to set value for the object, need to set values for DCPDP transmission interval and reception timeout simultaneously. | ||||
| CagentVpcDomainPeerDetectionTimeout | 1.3.6.1.4.1.4413.1.1.200.1.9.1.9 | Unsigned32 (700..14000) | RW | |
column · Unsigned32 (700..14000) · read-write · current To configure the DCPDP reception timeout. NOTE: In order to set value for the object, need to set values for DCPDP transmission interval and reception timeout simultaneously. | ||||
| CagentVpcDomainPeerIpAddr | 1.3.6.1.4.1.4413.1.1.200.1.9.1.10 | IpAddress | RW | |
column · IpAddress · read-write · current To configure IP address of the peer VPC switch. This configuration is used by the dual control plane detection protocol (DCPDP) on the VPC switches. NOTE: In order to set value for the object, need to set values for IP address of the peer MLAG switch and destination IP of the DCPDP message simultaneously. | ||||
| CagentVpcDomainSourceIpAddr | 1.3.6.1.4.1.4413.1.1.200.1.9.1.11 | IpAddress | RW | |
column · IpAddress · read-write · current To configure Self IP address of the VPC switch that is used as the source IP by the dual control plane detection protocol (DCPDP) on the VPC switches. NOTE: In order to set value for the object, need to set values for IP address of the peer MLAG switch and destination IP of the DCPDP message simultaneously. | ||||
| CagentVpcDomainDcpdpUdpPort | 1.3.6.1.4.1.4413.1.1.200.1.9.1.12 | Unsigned32 (1..65535) | RW | |
column · Unsigned32 (1..65535) · read-write · current To configure the UDP port on which the VPC switch listens to the DCPDP messages. Configurable range is 1 to 65535. Default value is 50000. NOTE: In order to set value for the object, need to set values for IP address of the peer MLAG switch, destination IP of the DCPDP message and UDP port on which the MLAG switch listens to the DCPDP messages simultaneously. | ||||
| CagentVpcDomainStatus | 1.3.6.1.4.1.4413.1.1.200.1.9.1.13 | RowStatus | RC | |
column · RowStatus · read-create · current Status of VPC Domain. | ||||
| NagentVpcPeerKeepAliveStatsGroup | 1.3.6.1.4.1.4413.1.1.200.2 | |||
| SagentVpcPeerKeepAliveTotalTx | 1.3.6.1.4.1.4413.1.1.200.2.1 | Unsigned32 | RO | |
scalar · Unsigned32 · read-only · current Total Packets transmitted | ||||
| SagentVpcPeerKeepAliveSuccessTx | 1.3.6.1.4.1.4413.1.1.200.2.2 | Unsigned32 | RO | |
scalar · Unsigned32 · read-only · current Successfully Transmitted Packets. | ||||
| SagentVpcPeerKeepAliveTxErrors | 1.3.6.1.4.1.4413.1.1.200.2.3 | Unsigned32 | RO | |
scalar · Unsigned32 · read-only · current Transmit Failed Packets. | ||||
| SagentVpcPeerKeepAliveTotalRx | 1.3.6.1.4.1.4413.1.1.200.2.4 | Unsigned32 | RO | |
scalar · Unsigned32 · read-only · current Total Packets Received. | ||||
| SagentVpcPeerKeepAliveSuccessRx | 1.3.6.1.4.1.4413.1.1.200.2.5 | Unsigned32 | RO | |
scalar · Unsigned32 · read-only · current Successfully Received Packets. | ||||
| SagentVpcPeerKeepAliveRxErrors | 1.3.6.1.4.1.4413.1.1.200.2.6 | Unsigned32 | RO | |
scalar · Unsigned32 · read-only · current Number of packets received with errors. | ||||
| SagentVpcPeerKeepAliveTimeoutCount | 1.3.6.1.4.1.4413.1.1.200.2.7 | Unsigned32 | RO | |
scalar · Unsigned32 · read-only · current Timeout counter. | ||||
| NagentVpcPeerLinkStatsGroup | 1.3.6.1.4.1.4413.1.1.200.3 | |||
| SagentVpcPeerLinkControlMsgTx | 1.3.6.1.4.1.4413.1.1.200.3.1 | Unsigned32 | RO | |
scalar · Unsigned32 · read-only · current Peer link control messages transmitted. | ||||
| SagentVpcPeerLinkTxErrors | 1.3.6.1.4.1.4413.1.1.200.3.2 | Unsigned32 | RO | |
scalar · Unsigned32 · read-only · current Peer link control messages Tx errors. | ||||
| SagentVpcPeerLinkTxTimeout | 1.3.6.1.4.1.4413.1.1.200.3.3 | Unsigned32 | RO | |
scalar · Unsigned32 · read-only · current Peer link control messages Tx timeout. | ||||
| SagentVpcPeerLinkControlMsgAckTx | 1.3.6.1.4.1.4413.1.1.200.3.4 | Unsigned32 | RO | |
scalar · Unsigned32 · read-only · current Peer link control messages ACK transmitted. | ||||
| SagentVpcPeerLinkControlMsgAckErrors | 1.3.6.1.4.1.4413.1.1.200.3.5 | Unsigned32 | RO | |
scalar · Unsigned32 · read-only · current Peer link control messages ACK Tx errors. | ||||
| SagentVpcPeerLinkControlMsgRx | 1.3.6.1.4.1.4413.1.1.200.3.6 | Unsigned32 | RO | |
scalar · Unsigned32 · read-only · current Peer link control messages received. | ||||
| SagentVpcPeerLinkDataMsgTx | 1.3.6.1.4.1.4413.1.1.200.3.7 | Unsigned32 | RO | |
scalar · Unsigned32 · read-only · current Peer link data messages transmitted. | ||||
| SagentVpcPeerLinkDataMsgTxErrors | 1.3.6.1.4.1.4413.1.1.200.3.8 | Unsigned32 | RO | |
scalar · Unsigned32 · read-only · current Peer link data messages Tx errors. | ||||
| SagentVpcPeerLinkDataMsgTxTimeout | 1.3.6.1.4.1.4413.1.1.200.3.9 | Unsigned32 | RO | |
scalar · Unsigned32 · read-only · current Peer link data messages Tx timeout. | ||||
| SagentVpcPeerLinkDataMsgRx | 1.3.6.1.4.1.4413.1.1.200.3.10 | Unsigned32 | RO | |
scalar · Unsigned32 · read-only · current Peer link data messages received. | ||||
| SagentVpcPeerLinkBPDUTx | 1.3.6.1.4.1.4413.1.1.200.3.11 | Unsigned32 | RO | |
scalar · Unsigned32 · read-only · current Peer link BPDU's transmitted to peer. | ||||
| SagentVpcPeerLinkBPDUTxErrors | 1.3.6.1.4.1.4413.1.1.200.3.12 | Unsigned32 | RO | |
scalar · Unsigned32 · read-only · current Peer link BPDU's Tx errors. | ||||
| SagentVpcPeerLinkBPDUrx | 1.3.6.1.4.1.4413.1.1.200.3.13 | Unsigned32 | RO | |
scalar · Unsigned32 · read-only · current Peer link BPDU's received from peer. | ||||
| SagentVpcPeerLinkBPDURxErrors | 1.3.6.1.4.1.4413.1.1.200.3.14 | Unsigned32 | RO | |
scalar · Unsigned32 · read-only · current Peer link BPDU's Rx errors. | ||||
| SagentVpcPeerLinkLACPDUTx | 1.3.6.1.4.1.4413.1.1.200.3.15 | Unsigned32 | RO | |
scalar · Unsigned32 · read-only · current Peer link LACPDU's tranmsitted to peer. | ||||
| SagentVpcPeerLinkLACPDUTxErrors | 1.3.6.1.4.1.4413.1.1.200.3.16 | Unsigned32 | RO | |
scalar · Unsigned32 · read-only · current Peer link LACPDU's Tx errors. | ||||
| SagentVpcPeerLinkLACPDUrx | 1.3.6.1.4.1.4413.1.1.200.3.17 | Unsigned32 | RO | |
scalar · Unsigned32 · read-only · current Peer link LACPDU's received from peer. | ||||
| SagentVpcPeerLinkLACPDURxErrors | 1.3.6.1.4.1.4413.1.1.200.3.18 | Unsigned32 | RO | |
scalar · Unsigned32 · read-only · current Peer link LACPDU's Rx errors. | ||||
| NagentVpcStatusGroup | 1.3.6.1.4.1.4413.1.1.200.4 | |||
| SagentVpcPeerLinkStatus | 1.3.6.1.4.1.4413.1.1.200.4.1 | TruthValue | RO | |
scalar · TruthValue · read-only · current Peer link operational status. | ||||
| SagentVpcTotalVpcConfigured | 1.3.6.1.4.1.4413.1.1.200.4.2 | Unsigned32 | RO | |
scalar · Unsigned32 · read-only · current Number of VPC's configured. | ||||
| SagentVpcTotalVpcOperational | 1.3.6.1.4.1.4413.1.1.200.4.3 | Unsigned32 | RO | |
scalar · Unsigned32 · read-only · current Number of VPC's operational. | ||||
| SagentVpcSelfRole | 1.3.6.1.4.1.4413.1.1.200.4.4 | INTEGER | RO | |
scalar · INTEGER · read-only · current VPC role.
| ||||
| SagentVpcOperationMode | 1.3.6.1.4.1.4413.1.1.200.4.5 | INTEGER | RO | |
scalar · INTEGER · read-only · current VPC operational mode.
| ||||
| SagentVpcPeerRole | 1.3.6.1.4.1.4413.1.1.200.4.6 | INTEGER | RO | |
scalar · INTEGER · read-only · current Vpc peer role.
| ||||
| SagentVpcKeepaliveOperationalMode | 1.3.6.1.4.1.4413.1.1.200.4.7 | INTEGER | RO | |
scalar · INTEGER · read-only · current VPC keepalive operational mode.
| ||||
| SagentVpcSystemMac | 1.3.6.1.4.1.4413.1.1.200.4.8 | MacAddress | RO | |
scalar · MacAddress · read-only · current System MAC address. | ||||
| SagentVpcState | 1.3.6.1.4.1.4413.1.1.200.4.9 | INTEGER | RO | |
scalar · INTEGER · read-only · current The following states of a VPC mean:
DISABLE: In this state, the VPC interfaces, if any are shut down.
LISTEN: The keepalive does not advertise any packets.
READY: The keepalive component starts sending keepalive messages periodically with the state as READY.
PRIMARY: Traffic over VPC interfaces is allowed to be forwarded.
The keepalive protocol continues to advertise keepalive messages with the state as PRIMARY.
SECONDARY: Traffic over VPC interfaces is allowed to be forwarded.
The keepalive protocol continues to advertise keepalive messages with the state as SECONDARY.
| ||||
| SagentVpcPeerPriority | 1.3.6.1.4.1.4413.1.1.200.4.10 | Unsigned32 | RO | |
scalar · Unsigned32 · read-only · current VPC peer priority. | ||||
| SagentVpcPeerMac | 1.3.6.1.4.1.4413.1.1.200.4.11 | MacAddress | RO | |
scalar · MacAddress · read-only · current VPC peer MAC address. | ||||
| SagentVpcPeerDetectionStatus | 1.3.6.1.4.1.4413.1.1.200.4.12 | TruthValue | RO | |
scalar · TruthValue · read-only · current VPC peer detection status. | ||||
| SagentVpcIsPeerDetected | 1.3.6.1.4.1.4413.1.1.200.4.13 | TruthValue | RO | |
scalar · TruthValue · read-only · current Indicates if the VPC peer is detected. | ||||
| TagentVpcSelfMemberStatusTable | 1.3.6.1.4.1.4413.1.1.200.4.14 | NA | ||
table · not-accessible · current VPC self member ports status table. | ||||
| RagentVpcSelfMemberStatusEntry | 1.3.6.1.4.1.4413.1.1.200.4.14.1 | NA | ||
row · not-accessible · current VPC self member port status entry. | ||||
| CagentVpcSelfMemberStatusVpcId | 1.3.6.1.4.1.4413.1.1.200.4.14.1.1 | Unsigned32 (1..63) | RO | |
column · Unsigned32 (1..63) · read-only · current VPC Id. | ||||
| CagentVpcSelfMemberStatusIntfId | 1.3.6.1.4.1.4413.1.1.200.4.14.1.2 | InterfaceIndex | RO | |
column · InterfaceIndex · read-only · current Interface Id. | ||||
| CagentVpcSelfMemberStatusIntfState | 1.3.6.1.4.1.4413.1.1.200.4.14.1.3 | INTEGER | RO | |
column · INTEGER · read-only · current VPC self member interface status.
| ||||
| TagentVpcPeerMemberStatusTable | 1.3.6.1.4.1.4413.1.1.200.4.15 | NA | ||
table · not-accessible · current VPC peer member ports status table. | ||||
| RagentVpcPeerMemberStatusEntry | 1.3.6.1.4.1.4413.1.1.200.4.15.1 | NA | ||
row · not-accessible · current VPC peer member port status entry. | ||||
| CagentVpcPeerMemberStatusVpcId | 1.3.6.1.4.1.4413.1.1.200.4.15.1.1 | Unsigned32 (1..63) | RO | |
column · Unsigned32 (1..63) · read-only · current VPC Id. | ||||
| CagentVpcPeerMemberStatusIntfId | 1.3.6.1.4.1.4413.1.1.200.4.15.1.2 | InterfaceIndex | RO | |
column · InterfaceIndex · read-only · current Interface Id. | ||||
| CagentVpcPeerMemberStatusIntfState | 1.3.6.1.4.1.4413.1.1.200.4.15.1.3 | INTEGER | RO | |
column · INTEGER · read-only · current VPC peer member interface status.
| ||||
| TagentVpcStatusTable | 1.3.6.1.4.1.4413.1.1.200.4.16 | NA | ||
table · not-accessible · current VPC status table. | ||||
| RagentVpcStatusEntry | 1.3.6.1.4.1.4413.1.1.200.4.16.1 | NA | ||
| CagentVpcStatusId | 1.3.6.1.4.1.4413.1.1.200.4.16.1.1 | Unsigned32 (1..63) | RO | |
column · Unsigned32 (1..63) · read-only · current VPC Id. | ||||
| CagentVpcOperationalStatus | 1.3.6.1.4.1.4413.1.1.200.4.16.1.2 | INTEGER | RO | |
column · INTEGER · read-only · current VPC operational status.
| ||||
| CagentPortChannelId | 1.3.6.1.4.1.4413.1.1.200.4.16.1.3 | InterfaceIndex | RO | |
column · InterfaceIndex · read-only · current Port-channel ID. | ||||
| CagentVpcInterfaceState | 1.3.6.1.4.1.4413.1.1.200.4.16.1.4 | INTEGER | RO | |
column · INTEGER · read-only · current The following states of a VPC port-channel interface mean:
DISABLE: The state of a port-channel before VPC functionality is enabled on it.
WAIT: The VPC port-channel 'waits' for the VPC functionality
to be enabled on a port-channel of the peer switch.
ERROR: After VPC is enabled on a port-channel of both peer switches,
the DOT3AD component checks to see if all entry criteria are met
for the port-channel to be operational.
ACTIVE: If the entry criteria are satisfied, then the VPC interface is set
to ACTIVE and is operationally enabled.
Traffic is now allowed to flow through the VPC member ports.
INACTIVE: If links connected to the VPC member ports are down,
then the VPC interface is set to INACTIVE on the switch.
The VPC will remain ACTIVE on the peer switch.
| ||||