MIB Browser

GAM-TC

Positron
Objects
0
Source
Show full MIB
snmptranslate -m GAM-TC -Tp

Imports

SNMPv2-CONFMODULE-COMPLIANCE, NOTIFICATION-GROUP
SNMPv2-SMIBits, Gauge32, Integer32, IpAddress, MODULE-IDENTITY, MibIdentifier, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, iso
SNMPv2-TCDisplayString, PhysAddress, TEXTUAL-CONVENTION

The site cannot show an OID tree for this MIB. Use Show full MIB to read the MIB file.

Textual conventions

GAMASRType INTEGER

any(0) range(2) specific(1)

Represents an Any/Specific/Range selector.
GAMASType INTEGER

any(0) specific(1)

Represents an Any/Specific selector.
GAMAdvDestMacType INTEGER

any(0) broadcast(3) multicast(2) specific(4) unicast(1)

Represents a destination MAC type selector.
GAMBitType INTEGER

any(0) one(2) zero(1)

Represents a bit selector.
GAMDestMacType INTEGER

any(0) broadcast(3) multicast(2) unicast(1)

Represents a destination MAC type selector.
GAMDisplayString OCTET STRING (SIZE (0..255))

Display hint: 255a

Represents textual information taken from the ASCII character
set, as defined in ANSI X3.4-1986 with some restrictions.

The following rules apply:

 - only character codes 32-126 (decimal) are supported

 - the graphics characters (32-126) are interpreted as
   US ASCII

Any object defined using this syntax may not exceed 255
characters in length.
GAMEtherType Gauge32 (0..65535)

Display hint: 2x

Represents a 16-bit Ethernet Type.
GAMInetAddress OCTET STRING (SIZE (1..253))

Display hint: 255a

Represents an internet address. Following is the list of supported
address types: IPv4 address, IPv6 address, Domain name or No-Address.

The addresses are encoded as a human readable string as defined here:

 - IPv4 address is encoded as 'a.b.c.d' where a-d are integer numbers in
   the range from 0-255.

 - IPv6 address is encoded as defined in RFC5952.

 - Domain names are passed through in their native representation.

 - No-Address is encoded as the string literal: '<no-address>'.

This type is not allowed to be used as indices in tables.
GAMInteger16 INTEGER (-32768..32767)

Display hint: d

Represents a 16-bit signed integer.
GAMInteger32e-9 INTEGER

Display hint: d

Represents a 32-bit signed integer times 10E-9
GAMInteger64 OCTET STRING (SIZE (8))

Display hint: 8x

Represents a 64-bit signed integer encoded as two's complement in
network order.
GAMInteger8 INTEGER (-128..127)

Display hint: d

Represents an 8-bit signed integer.
GAMInterfaceIndex Integer32 (0..2147483647)

Display hint: d

The interface index is a unique identification of an arbitrary
interface in the system. Example of interfaces could be physical ports,
aggregations, VLAN interfaces and others.

The interface indexes used by the system is deterministic and is
chosen using the schema below.

NONE                          0 -             0 (standalone/stacking)

VLAN                          1 -         4.095 (standalone/stacking)

Usid1 /ports          1.000.001 -     1.000.999 (standalone/stacking)
..
Usid16/ports         16.000.001 -    16.000.999 (stacking)

Usid1 /llagr          1.005.001 -     1.005.999 (standalone/stacking)
..
Usid16/llagr         16.005.001 -    16.005.999 (stacking)

GLAG                100.000.001 -   100.000.999 (standalone/stacking)

EVC                 200.000.001 -   200.099.999 (standalone)

MPLS links          300.000.001 -   300.009.999 (standalone)

MPLS tunnels        400.000.001 -   400.099.999 (standalone)

MPLS pseudo-wires   500.000.001 -   500.099.999 (standalone)

MPLS lsp            600.000.001 -   600.099.999 (standalone)
GAMIpAddress OCTET STRING (SIZE (1..46))

Display hint: 255a

Represents an internet address. Following is the list of supported
address types: IPv4 address, IPv6 address or No-Address.

The addresses are encoded as a human readable string as defined here:

 - IPv4 address is encoded as 'a.b.c.d' where a-d are integer numbers in
   the range from 0-255.

 - IPv6 address is encoded as defined in RFC5952.

 - No-Address is encoded as the string literal: '<no-address>'.
GAMMacStringList OCTET STRING (SIZE (0..4095))

Display hint: 4095a

Textual representation of a list of MAC address sisplayed
in ASCII format.

Each MAC address has the format xx:xx:xx:xx:xx:xx, and
they are separated by a comma.

Example:
  00:01:02:03:04:05,06:07:08:09:0a:0b,ab:cd:ef:01:02:03

Any object defined using this syntax may not exceed 4095
characters in length.

The actual maximum length may be restricted by the
individual context where this type is used (for example, a
MAC list may be restricted to 16 entries, in which case
the maximum length would be 287 characters, according to
the above rules).
GAMMepDmTimeUnit INTEGER

microSeconds(0) nanoSeconds(1)

Calculation Delay Measurement time unit.
GAMMepInstanceDirection INTEGER

down(0) up(1)

The MEP instance direction.
GAMMepTxRate INTEGER

frames100PerSecond(2) frames10PerSecond(3) frames1PerMinute(6) frames1PerSecond(4) frames300PerSecond(1) frames6PerHour(7) frames6PerMinute(5) invalid(0)

MEP PDU transmission rate.
GAMPercent Gauge32 (0..100)

Display hint: d

An integer in the range 0..100 representing a percent value
GAMPortList OCTET STRING (SIZE (1..128))

Display hint: 128x

A list of ports that may be distributed across more stack units.

The type should be interpreted as a sequence of bits, each bit
representing a port. If a bit is set (1) the represented port is
included in the port list. If a bit is not set (0) the represented port
is not included in the port list.

Each switch in a stack is represented by an ID in the range [1-16] both
included. Each switch in the stack has a reserved range of 64 bits
or 8 bytes in this octet string. If the switch is not stackable it will
be represented as 'Switch 1'.

The switch with ID 1 owns the byte range 0-7, switch ID 2 owns the
byte range 8-15, etc.

The physical ports are represented by the bit index relative to the
range owned by a given switch. Bit number zero is the least significant
bit of the first entry in the byte sequence owned by the switch (port
number 0 if such a port exists). Bit number one is the second least
significant bit in the first byte of the range owned by the switch.

This is illustrated below:

 Port 7 switch 1                 Port 7 switch 2
 ^    Port 0 switch 1            ^    Port 0 switch 2
 |    ^ Port 15 switch 1         |    ^     Port 63 switch 2
 |    | ^    Port 8 switch 1     |    |     ^     Port 56 switch 2
 |    | |    ^ Port 23 switch 1       |     |     ^
 |    | |    | ^    Port 16 switch 1        |     |
 |    | |    | |    ^     Port 63 switch 1        |
 |    | |    | |    |     ^    Port 56 switch 1   |
 |    | |    | |    |     |    ^                  |
 |    | |    | |    |     |    | |    |     |     |
 v    v v    v v    v     v    v v    v     v     v
+---------------------------------------------------------------+
|byte 0|byte 1|byte 2|...|byte 7|byte 8|...|byte 15|...|byte 127|
+---------------------------------------------------------------+
\______________  ______________/ \________  ______/ \____  ____/
               \/                         \/             \/
             Switch 1                  Switch 2       Switch 3-16

The octet string is truncated at most significant byte which is not
zero. An empty port list is encoded as [0x00].

Example: a non-stackable switch where 48 is the highest port number
needs seven bytes to represent a complete port list. If the port list
only contains port 1, 2 and 20 then the SNMP encoded port list is:
[0x06, 0x00, 0x10].

NOTE: Even though port 0 does not exists in the port map it is still
represented by a bit in this port list. The same is true for the higher
indices. Configuring non-existing ports using the port list will have
no effect on the target.
GAMPortStatusSpeed INTEGER

speed100M(2) speed10G(6) speed10M(1) speed12G(7) speed1G(3) speed2G5(4) speed5G(5) undefined(0)

This enumerations show the current interface speed.
GAMPsecUserBitmaskType Gauge32

Display hint: 2x

Bitmask for representing users of the Port Security module.
The administrative user is represented by the least significant bit
and the remaining bits represent software modules that also may
control whether to forward or block a given MAC address.
Encoding:
bit 0 represents the administrative user.
bit 1 represents 802.1X.
bit 2 represents DHCP Snooping.
bit 3 represents Voice VLAN.
GAMQosShaperRateType INTEGER

data(1) line(0)

Indicates the shaper's rate type.

If the value is zero, it indicates the shaper uses line-rate.
If the value is one, it indicates the shaper uses data-rate.

NOTE: For QoS Queue shapers, this configuration is valid only for Normal
port mode. If the port is in Basic or Hierarchical mode, the rate-type
will be stored and become active when the port is switched back to
Normal Scheduling mode.
GAMRfc5517Mode INTEGER

community(2) isolated(1) stacking(4) stacking-isolated(5) undefined(0) uplink(3)

This enumerations show the current interface RFC 5517 mode.
GAMRowEditorState Gauge32

Display hint: d

The RowEditorState is used both as a column in the dynamic tables, and
as a object in the row editor. The meaning of the row editor state
depends on the context where it is used.

In either case it is used to implement actions related to add or delete
columns in dynamic tables.

When used as a column in a dynamic table
----------------------------------------

Read back of this value will always be zero. If the value 1 is written
to this object the given row will be deleted. Values different from 0
and 1 are reserved for future use and should not be used.

When used as an object in a row editor
--------------------------------------

A value used to control the row editor protocol. The values 0-255 are
reserved to be used in the row editor protocol, all other values tokes
the manager can use to reserve the row editor.

The values 0, 1 and 2 is currently use din the row editor protocol
while the values 3-255 are reserved for future use.

Following is the names of the values used in the row editor protocol:

  0:              IDLE STATE
  1:              CLEAR-ACTION
  2:              COMMIT-ACTION
  256-4294967295: MANAGER-ID

The following state machine defines the row editor protocol:

        +--------------+                 +------------------+
        |              |<----------------|                  |
        |              |   CLEAR         |                  |
        |     IDLE     |<----------------|     RESERVED     |
        |              |   COMMIT        |                  |
        |              |---------------->|                  |
        +--------------+   MANAGER-ID    +------------------+

When the RowEditorState is being read one will either read the value
zero: meaning that the row editor is in the idle state. Or a value
between 256-4294967295: meaning that the row editor is reserved with
the given ID.

When the row editor is in the IDLE state the manager may try to reserve
it by writing its own MANAGER-ID to the RowEditorState object. If the
write succeeds the manager can read-back the MANAGER-ID.

When the row editor is in the RESERVED state the manager can either
clear the changes by writing CLEAR, or it can commit the changes by
writing COMMIT. Both actions will cause the state to jump back to the
IDLE state, but only the COMMIT will cause the row to be added.
GAMSfpTransceiver INTEGER

none(0) notSupported(1) sfp1000BaseCx(8) sfp1000BaseLx(10) sfp1000BaseSx(9) sfp1000BaseT(7) sfp1000BaseX(11) sfp100FX(2) sfp10G(14) sfp2G5(12) sfp5G(13)

This enumerations show the SFP transceiver type.
GAMTimeStamp OCTET STRING (SIZE (8))

Display hint: 8x

Represents a timestamp in seconds since epoch. The data is encoded as
a 64-bit unsigned integer in network order.
GAMUnsigned16 Gauge32 (0..65535)

Display hint: d

Represents a 16-bit unsigned integer.
GAMUnsigned64 OCTET STRING (SIZE (8))

Display hint: 8x

Represents a 64-bit unsigned integer encoded in network order.
GAMUnsigned8 Gauge32 (0..255)

Display hint: d

Represents an 8-bit unsigned integer.
GAMVcapKeyType INTEGER

doubleTag(1) ipAddr(2) macIpAddr(3) normal(0)

Represents a VCAP key type selector.
GAMVclProtoEncap OCTET STRING (SIZE (3..6))

Display hint: 6x

Represents a protocol encapsulation, needed by the Protocol part of
the VCL module.

The protocol encapsulation type, along with the respective encapsulation
fields are encoded as an octet string of variable size ranging from 3 to 6.

Currently, the VCL module only supports three protocol encapsulation types:

- Ethernet II encapsulation, defined by setting the first octet to 1. Two more
  octets are used to describe the 'type' field. The type can range from 0x0600-0xffff.

  I.e. ETH2:    1            TYPE
             {byte 0} {byte 1 +  byte 2}

  E.g. 1.2048 := ETH2, TYPE = 0x0800

- LLC SNAP encapsulation, defined by setting the first octet to 2. Three more
  octets are used for the 'OID' field and two for the 'PID' field. The OID can range
  from 0x000000-0xffffff and the PID from 0x0000-0xffff. Special case is when OID is
  0x000000; then PID can only range from 0x0600-0xffff.

  I.e. LLC-SNAP:    2      OUI[0]   OUI[1]   OUI[2]         PID
                 {byte 0} {byte 1} {byte 2} {byte 3} {byte 4 +  byte 5}

  E.g. 2.0.1.24.562 := SNAP, OUI = 0x00:01:18, PID = 0x0232

- LLC Other encapsulation, defined by setting the first octet to 3. Two more
  octets are used for the 'DSAP' and 'SSAP' fields respectively. Each of these two fields
  can range from 0-255

  I.e. LLC-OTHER:    3       DSAP     SSAP
                  {byte 0} {byte 1} {byte 2}

  E.g. 3.42.85 := LLC, DSAP = 0x2A, SSAP = 0x55

Default, empty encapsulation is 0.0.0
GAMVlan Gauge32 (1..4095)

Display hint: d

An integer representing a VLAN ID.
GAMVlanListQuarter OCTET STRING (SIZE (128))

Display hint: 128x

A list representing 1024 VLAN IDs.

The type should be interpreted as a sequence of bits, each bit
representing one VLAN ID. If a bit is set (1) the represented VLAN is
included in the VLAN list. If a bit is not set (0) the represented VLAN
is not included in the VLAN list.

The least significant bit of each byte represents a smaller VLAN ID
than a more significant bit of a byte.

If for example the VLAN list represents VLAN IDs from 0 to 1023,
bit 0 of the first byte represents VLAN ID 0, bit 1 of the first byte
represents VLAN ID 1, and so on. The most significant bit of the 128th
byte therefore represents VLAN ID 1023.

An implementation that needs to represent all 4K VLANs will divide
the VLAN list into four equally sized objects. VLAN ID 0 is included
in the first object even though it is not used.
GAMVlanOrZero Gauge32 (0..4095)

Display hint: d

An integer representing a VLAN ID or zero.
GAMVlanTagPriority INTEGER

any(0) range0to1(9) range0to3(13) range2to3(10) range4to5(11) range4to7(14) range6to7(12) value0(1) value1(2) value2(3) value3(4) value4(5) value5(6) value6(7) value7(8)

VLAN priority.
GAMVlanTagType INTEGER

any(0) cTagged(3) sTagged(4) tagged(2) untagged(1)

Represents a VLAN tag type selector.

Used by