TSDIM-SNMPNE-MIB
Nokia (formerly 'Alcatel-Lucent')TSD-IM SNMP NE MIB
snmptranslate -m TSDIM-SNMPNE-MIB -Tpsnmpwalk -v2c -c <community> -m TSDIM-SNMPNE-MIB <host> 1.3.6.1.4.1.637.54.1.1.5Imports
| IANAifType-MIB | IANAifType |
|---|---|
| IF-MIB | InterfaceIndex, ifIndex |
| OPTICSIM-COMMON-TC | OpticsIMPmPeriodTime |
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP |
| SNMPv2-SMI | Bits, Counter32, Gauge32, Integer32, IpAddress, MODULE-IDENTITY, MibIdentifier, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, iso |
| SNMPv2-TC | DateAndTime, DisplayString, MacAddress, PhysAddress, RowStatus, TEXTUAL-CONVENTION, TruthValue |
| TSDIM-BASICREG-MIB | tsdimBasicMC, tsdimBasicMib |
| TSDIM-SNMP-TC | OpticsIMUserLabel, SLValue, TsdimEventTimeInt, TsdimManagerType, TsdimUdpPort |
| TSDIM-SUPPORT-MIB | InetAddressIPv6, opticsIMAdditionalText, opticsIMAlarmType, tsdimAlarmSeverity, tsdimAlarmSpecProblem, tsdimEventNotificationId, tsdimEventObjectClassIdentifier, tsdimEventObjectInstanceIdentifier, tsdimEventTime |
OID tree
| Name | OID | Type | Access | Status | Example |
|---|---|---|---|---|---|
| ItsdimSnmpNEMib | 1.3.6.1.4.1.637.54.1.1.5 | ||||
identity TSD-IM SNMP NE MIB | |||||
| NtsdimSnmpNEMibObject | 1.3.6.1.4.1.637.54.1.1.5.1 | ||||
| StsdimSnmpAgtIpAddress | 1.3.6.1.4.1.637.54.1.1.5.1.1 | IpAddress | RW | ||
scalar · IpAddress · read-write · current This scalar object defines the Agent Ip Address | |||||
| StsdimSnmpAgtUdpPort | 1.3.6.1.4.1.637.54.1.1.5.1.2 | TsdimUdpPort | RW | ||
scalar · TsdimUdpPort · read-write · current This scalar object defines the Agent UDP Port. | |||||
| StsdimSnmpAgtIpMask | 1.3.6.1.4.1.637.54.1.1.5.1.3 | IpAddress | RW | ||
scalar · IpAddress · read-write · current This scalar object defines the Agent Ip Mask | |||||
| StsdimNeInstallationType | 1.3.6.1.4.1.637.54.1.1.5.1.5 | DisplayString | RO | Wavence-SA | |
| StsdimSdhNeLabel | 1.3.6.1.4.1.637.54.1.1.5.1.13 | DisplayString | RW | Microwave-radio | |
| StsdimBoardPosition | 1.3.6.1.4.1.637.54.1.1.5.1.14 | Integer32 | RO | ||
scalar · Integer32 · read-only · current This object defines the board position in term of <rrssbb> | |||||
| TtsdimLacTable | 1.3.6.1.4.1.637.54.1.1.5.1.17 | NA | |||
table · not-accessible · current The TSDIM Local Access control table. This table is used to give access to the Craft Terminals. | |||||
| RtsdimLacEntry | 1.3.6.1.4.1.637.54.1.1.5.1.17.1 | NA | |||
row · not-accessible · current Entry is automatically created by Agent at start-up time.
| |||||
| CtsdimLacState | 1.3.6.1.4.1.637.54.1.1.5.1.17.1.1 | INTEGER | RW | ||
column · INTEGER · read-write · current This is the State attribute for the Local Access Control. This attribute can be set: - by Agent at creation time to accessRequested - by EML to the values accessGranted or accessDenied
| |||||
| CtsdimLacNoResponseTimeOutPeriod | 1.3.6.1.4.1.637.54.1.1.5.1.17.1.2 | Integer32 (0..3600) | RW | ||
column · Integer32 (0..3600) · read-write · current This is the No Response TimeOut Period attribute for the Local Access \ Control.
| |||||
| CtsdimLacIndex | 1.3.6.1.4.1.637.54.1.1.5.1.17.1.3 | Integer32 | NA | ||
column · Integer32 · not-accessible · current This is the index for the Local Access Control table. | |||||
| SopticsIMNeOwnsByMgr | 1.3.6.1.4.1.637.54.1.1.5.1.18 | DisplayString | RW | ||
scalar · DisplayString · read-write · current This scalar object contains the label which identify the manager that is managing the NE | |||||
| TopticsIMIfTable | 1.3.6.1.4.1.637.54.1.1.5.1.19 | NA | |||
table · not-accessible · current This table contains interface configuration not defined in the IfTable (see inside the IF-MIB). | |||||
| RopticsIMIfEntry | 1.3.6.1.4.1.637.54.1.1.5.1.19.1 | NA | |||
| CtsdimIfUnderlieLayer | 1.3.6.1.4.1.637.54.1.1.5.1.19.1.1 | INTEGER | RW | ||
column · INTEGER · read-write · current This object contains the reference to the underlying path layer termination point. This object can be set only when used as physical interface. The default value is <none>.
| |||||
| CtsdimIfAsapIndex | 1.3.6.1.4.1.637.54.1.1.5.1.19.1.2 | Integer32 (1..2147483647) | RW | ||
column · Integer32 (1..2147483647) · read-write · current This object defines the ASAP object associated to this interface. | |||||
| CtsdimIfOwnsByMgr | 1.3.6.1.4.1.637.54.1.1.5.1.19.1.3 | TsdimManagerType | RW | ||
column · TsdimManagerType · read-write · current This attribute defines the manager which is the owner of the resources involved in this connection | |||||
| CopticsIMIfTxSL | 1.3.6.1.4.1.637.54.1.1.5.1.19.1.4 | SLValue | RO | ||
column · SLValue · read-only · current This attribute defines the SL value transmitted in the outgoing direction. | |||||
| CopticsIMIfExpSL | 1.3.6.1.4.1.637.54.1.1.5.1.19.1.5 | SLValue | RO | ||
column · SLValue · read-only · current This attribute defines the SL value expected in the incoming direction. | |||||
| CopticsIMIfRxSL | 1.3.6.1.4.1.637.54.1.1.5.1.19.1.6 | SLValue | RO | ||
column · SLValue · read-only · current This attribute defines the SL value received in the incoming direction. | |||||
| CopticsIMIfSLSendControl | 1.3.6.1.4.1.637.54.1.1.5.1.19.1.7 | INTEGER | RW | ||
column · INTEGER · read-write · current This attribute defines if the transmitted SL value shall be defined by the agent according to the payload type or it should be the 'equipped-non-specific' code. The value 'automatic' (0) means that the tx SL is calculated by the agent according to the payload type. The value 'forced' (1) means that the tx SL has been forced by the manager to the 'equipped-non-specific' code. This object can be set when the AdminStatus is down or up.
| |||||
| CopticsIMIfBridgeBasePort | 1.3.6.1.4.1.637.54.1.1.5.1.19.1.8 | Integer32 (0..65535) | RO | ||
column · Integer32 (0..65535) · read-only · current This attribute value is the bridge port number which lets manager get bridge tables indexed by this number. The default value is equal to zero when no bridge port is created and associated by SNMP agent. When a bridge port can be equipped (its related Ethernet interface is Up, with promiscuous mode and with ETB characterization in case of IEEE 8021.d, 8021.q or also with ETS characterization in case of IEEE 8021.ad), SNMP agent assigns its chosen index to this attribute | |||||
| CopticsIMIfRateLimitedSpeed | 1.3.6.1.4.1.637.54.1.1.5.1.19.1.9 | Gauge32 | RW | ||
column · Gauge32 · read-write · current This attribute carries out the rate limiting functionality. ifSpeed value means that the rate limitation of the interface is disabled; this is the default value. The value 0 means that the rate limitation of the interface is disabled; this is the default value. The value can be expressed in bit/s or kbit/s NE dependent | |||||
| CopticsIMIfMeanEgressShapingRate | 1.3.6.1.4.1.637.54.1.1.5.1.19.1.10 | Gauge32 | RW | ||
column · Gauge32 · read-write · current This attribute carries out the egress shaping rate (sustained rate permitted by egress traffic shaping) in kbit/sec. Disabled rate limitation is the default value. | |||||
| CopticsIMIfBurstEgressShapingSize | 1.3.6.1.4.1.637.54.1.1.5.1.19.1.11 | Unsigned32 | RW | ||
column · Unsigned32 · read-write · current This attribute carries out the burst egress shaping size (amount of traffic in excess of egress shaping rate) in bytes. Default value 0 (null burst egress shaping size) | |||||
| CopticsIMIfSchedulingDiscipline | 1.3.6.1.4.1.637.54.1.1.5.1.19.1.12 | INTEGER | RW | ||
column · INTEGER · read-write · current This object defines 'on per port basis' scheduling disciplines according to below values: - WorkConserving (1) - NonWorkConserving (2). Default value is WorkConserving(1) | |||||
| CopticsIMIfEntryPortTrafficEnabled | 1.3.6.1.4.1.637.54.1.1.5.1.19.1.13 | INTEGER | RW | ||
column · INTEGER · read-write · current opticsIMifEntryPortTrafficEnabled specifies the current transmit/receive state of the interface as a result of explicit management action applied to an interface whose ifAdminStatus is up. The up(1) value indicates the interface is ready to transmit and receive network traffic, the down(2) value indicates the interface has blocked both transmit and receive traffic capabilities. If ifAdminStatus is down, then opticsIMifEntryPortTrafficEnabled takes down(2) value, if ifAdminStatus is changed to up(1) then opticsIMifEntryPortTrafficEnabled changes to up(1)
| |||||
| CopticsIMIfAdmittedFloodingRate | 1.3.6.1.4.1.637.54.1.1.5.1.19.1.14 | Gauge32 | RW | ||
column · Gauge32 · read-write · current This attribute carries out 'on per port basis' ingress admitted flooding rate (the threshold value of admitted bandwidth for NE generated flooding traffic as admitted on this ingress interface) and is specified in kilobits per second (Kbps). This value is requested to trigger discarding of NE generatedflooding traffic on this ingress interface and is minor or equal to that specified in ifSpeed for this interface. Disabled flooding rate limitation is the default value | |||||
| CopticsIMIfHashInput | 1.3.6.1.4.1.637.54.1.1.5.1.19.1.15 | OpticsIMHashingKeyList | RW | ||
column · OpticsIMHashingKeyList · read-write · current This attribute enables to choose out 'on per link aggregation interface basis' ingress parameters for hash function. If the bit is 1 it indicates that the relative hashing key parameter will be used for Link Aggregation hash function otherwise if 0 it will be unused. Default value is: a) for Link Aggregation Interface in promiscous mode: bit 0 (MAC DA) and bit 1 (MAC SA) set to 1 and all other bits set to 0; b) for Link Aggregation in non-promiscous mode: bit 6 (All MPLS Labels) set to 1 and all other bits set to 0. This attribute is significant only for Link Aggregation interface | |||||
| CopticsIMIfDemarcRole | 1.3.6.1.4.1.637.54.1.1.5.1.19.1.16 | INTEGER | RW | ||
column · INTEGER · read-write · current The Current role of the Port. Ports connected with Customer Network will be called as CustomerInterface(1). Ports connected with Provider Network will be called as NetworkINterface(2). The ports which are internally connected to CPU and FPGA are called as Internal(3). The ports which are connected to internal equipment for data traffic are called as internalTraffic (5). The ports which are connected to internal equipment to provide power are called as internalPower (6). The ports which are connected to external equipment to provide power are called as equipmentPower (7).
| |||||
| CopticsIMIfLacpEnable | 1.3.6.1.4.1.637.54.1.1.5.1.19.1.17 | TruthValue | RC | ||
column · TruthValue · read-create · current This parameter enables the usage of LACP protocol over Link Aggregation interface. Default value is True (enabled LACP) | |||||
| CopticsIMIfVplsPortRole | 1.3.6.1.4.1.637.54.1.1.5.1.19.1.18 | INTEGER | RW | ||
column · INTEGER · read-write · current The Current role of a Port inside VPLS PE. Ports connected with Customer Network will be called as vpls_uni(1). Ports connected with MPLS Core PW will be called as vpls_nni(4). Spoke ports carrying PVLAN will be called as pvlan_spoke(2). Spoke ports carrying PW will be called as pw_spoke(3). Provider Bridge Network Port will be called as other(5).
| |||||
| CopticsIMIfRateLimitedDcnTraffic | 1.3.6.1.4.1.637.54.1.1.5.1.19.1.19 | Gauge32 | RW | ||
column · Gauge32 · read-write · current This attribute carries out the rate limiting functionality for DCN traffic (control Plane and Management Plane) addressed to CPU. A value equal to interface line-rate means that the rate limitation of DCN traffic is disabled; this is the default value. The value can be expressed in bit/s or kbit/s NE dependent | |||||
| CopticsIMIfDownstreamPortSetPorts | 1.3.6.1.4.1.637.54.1.1.5.1.19.1.20 | PortList | RC | ||
column · PortList · read-create · current The set of NE ports which are permanently assigned by management to the egress downstream port list (list of egress ports supporting trasmitter shutdown or insertion of GFP CSF frames) in front of failure occurring on this interface. The bit position in the egress downstream port list is coded according to the dot1dBasePort parameter. The default value of this object is a string of zeros of appropriate length, indicating not being a member (egress port without trasmitter shutdown and GFP CSF failure propagation). This attribute is relevant ONLY in case of opticsIMEthETSServiceType equal to other. | |||||
| CopticsIMIfUpstreamPortSetPorts | 1.3.6.1.4.1.637.54.1.1.5.1.19.1.21 | PortList | RC | ||
column · PortList · read-create · current The set of NE ports which are permanently assigned by management to the upstream port list, where upstream port list includes those NE ports able to trigger transmitted shut-down consequent action on this interface: operational consequent action on this interface is constrained to combined failure conditions detected (logical AND) over entire upstream port list. The bit position in the ingress upstream port list is coded according to the dot1dBasePort parameter. The default value of this object is a string of zeros of appropriate length, indicating not being a member (ingress port triggering no consequent action). This attribute is relevant ONLY in case of opticsIMEthETSServiceType equal to other. | |||||
| CopticsIMIfBroadcastTrafficEnable | 1.3.6.1.4.1.637.54.1.1.5.1.19.1.22 | TruthValue | RW | ||
column · TruthValue · read-write · current opticsIMifBroadcastTrafficEnable specifies the broadcast traffic transmit capability of an egress interface as a result of explicit management action. True value (Default value) indicates the interface is enabled to transmit broadcast traffic, false value indicates the interface is denied to transmit broadcast traffic. | |||||
| CopticsIMIfUnknownTrafficEnable | 1.3.6.1.4.1.637.54.1.1.5.1.19.1.23 | TruthValue | RW | ||
column · TruthValue · read-write · current opticsIMifUnknownTrafficEnable specifies the unknown traffic transmit capability of an egress interface as a result of explicit management action. True value (Default value) indicates the interface is enabled to transmit unknown traffic, false value indicates the interface is denied to transmit unknown traffic. | |||||
| CopticsIMIfPdhRate | 1.3.6.1.4.1.637.54.1.1.5.1.19.1.24 | INTEGER | RW | ||
column · INTEGER · read-write · current This parameter specifies the type of PDH signal carried by the interface.
| |||||
| CopticsIMIfOffsetEgressShapingSize | 1.3.6.1.4.1.637.54.1.1.5.1.19.1.25 | Unsigned32 | RW | ||
column · Unsigned32 · read-write · current This attribute carries out the server-layer offset (in bytes) for each specific frame. As a consequence, per-port basis egress shaping rate is decreased by a delta value inferred via per-frame basis server-layer encapsulation header. Default value is indicated as 0xFFFF and is internally set according to the following considerations: - if opticsIMNeFrameSizeMode is equal to layer2 than the default set is equal to 0 (no offset). - if opticsIMNeFrameSizeMode is equal to layer1 than the default set is interface type specific | |||||
| CopticsIMIfPIPMacAddress | 1.3.6.1.4.1.637.54.1.1.5.1.19.1.26 | PhysAddress | RW | ||
column · PhysAddress · read-write · current This attribute contains user-provisioned PIP MAC address | |||||
| CopticsIMIfMCEnable | 1.3.6.1.4.1.637.54.1.1.5.1.19.1.27 | TruthValue | RC | ||
column · TruthValue · read-create · current This parameter enables the interworking with Media Converter. Default value is False (no interworking with Media Converter) | |||||
| CopticsIMIfLPTSendControl | 1.3.6.1.4.1.637.54.1.1.5.1.19.1.28 | INTEGER | RW | ||
column · INTEGER · read-write · current This attribute enables or disables the usage of per-port LPT transmit capability. Allowed values: - disabled (0) no consequent LPT frame (IDLE insertion) - gfpcsf (1) via opticsimGFPConfCsf - linkoam (2) 802.3ah This object can be set when the AdminStatus is down or up. | |||||
| CopticsIMIfLPTCsfConsequentActions | 1.3.6.1.4.1.637.54.1.1.5.1.19.1.29 | INTEGER | RW | ||
column · INTEGER · read-write · current This attribute defines per-port LPT CSF Consequent Actions
This object identifies the consequent action triggered on
CIF Interface egress port for port-to-port application
in front of received LPT Frame indications
(due to detected remote CIF Ethernet PHY Interface failures).
The choice of enabled LPT CSF consequent actions is allowed to be
different from LPT SSF consequent actions (consequent actions
coping with network failures).
Allowed values:
- disabled (0) - default value - is defined to perform
no consequent actions.
- tx_shutdown(1) is defined to trigger forced transmitter
shut-down action
- gfp_csf (2) is defined to trigger GFP CSF transmission
- linkoam_cle (3) is defined to trigger Link OAM CLE transmission
If the interface is not involved in a port-to-port application
this consequent action will never be triggered.
This object can be set when the AdminStatus is down or up. | |||||
| CopticsIMIfLPTSsfConsequentActions | 1.3.6.1.4.1.637.54.1.1.5.1.19.1.30 | INTEGER | RW | ||
column · INTEGER · read-write · current This attribute defines per-port LPT SSF Consequent Actions
This object identifies the consequent action triggered on
CIF Interface egress port for port-to-port application
in front of Server Layer failures.
The choice of enabled LPT SSF consequent actions is allowed to be
different from LPT CSF consequent actions (consequent actions
coping with in front of LPT Frame indications).
Allowed values:
- disabled (0) - default value - is defined to perform
no consequent actions.
- tx_shutdown(1) is defined to trigger forced transmitter
shut-down action
- gfp_csf (2) is defined to trigger GFP CSF transmission
- linkoam_cle (3) is defined to trigger Link OAM CLE transmission
If the interface is not involved in a port-to-port application
this consequent action will never be triggered.
This object can be set when the AdminStatus is down or up. | |||||
| CopticsIMIfLPTHoldOffTime | 1.3.6.1.4.1.637.54.1.1.5.1.19.1.31 | INTEGER (0..100) | RW | ||
column · INTEGER (0..100) · read-write · current This attribute specifies consequent Actions Hold-Off values in steps di 0.1 sec. Default Value is 0 | |||||
| CopticsIMIfBroadcastTrafficLimit | 1.3.6.1.4.1.637.54.1.1.5.1.19.1.32 | Gauge32 | RW | ||
column · Gauge32 · read-write · current This attribute carries out 'on per port basis' ingress admitted broadcast traffic rate (the threshold value of broadcast traffic rate as admitted on this ingress interface) and is specified in Kilobits per second (Kbps). This value is requested to trigger discarding of NE generated broadcast traffic on this ingress interface and is minor or equal to that specified in ifSpeed for this interface. Disabled broadcast traffic rate limitation is the default value. | |||||
| CopticsIMIfMulticastTrafficLimit | 1.3.6.1.4.1.637.54.1.1.5.1.19.1.33 | Gauge32 | RW | ||
column · Gauge32 · read-write · current This attribute carries out 'on per port basis' ingress admitted multicast traffic rate (the threshold value of multicast traffic rate as admitted on this ingress interface) and is specified in Kilobits per second (Kbps). This value is requested to trigger discarding of NE generated multicast traffic on this ingress interface and is minor or equal to that specified in ifSpeed for this interface. Disabled multicast traffic rate limitation is the default value. | |||||
| CopticsIMIfUnknownUnicastTrafficLimit | 1.3.6.1.4.1.637.54.1.1.5.1.19.1.34 | Gauge32 | RW | ||
column · Gauge32 · read-write · current This attribute carries out 'on per port basis' ingress admitted unknown unicast rate (the threshold value of unknown unicast traffic rate as admitted on this ingress interface) and is specified in Kilobits per second (Kbps). This value is requested to trigger discarding of NE generated unknown unicast traffic rate on this ingress interface and is minor or equal to that specified in ifSpeed for this interface. Disabled unknown unicast limitation is the default value. | |||||
| CopticsIMIfAvailableBandwidth | 1.3.6.1.4.1.637.54.1.1.5.1.19.1.35 | Integer32 (1..2147483647) | RO | ||
column · Integer32 (1..2147483647) · read-only · current This value indicates the total amount of available bandwidth available on this interface and is specified in kilobits per second (Kbps). This value is calculated as the difference between the amount of bandwidth currently in use and that specified in ifSpeed (converted in Kbps). When this value cannot be measured, this value should contain the nominal bandwidth. | |||||
| CopticsIMIfNetBandwidth | 1.3.6.1.4.1.637.54.1.1.5.1.19.1.36 | Integer32 (1..2147483647) | RO | ||
column · Integer32 (1..2147483647) · read-only · current This value indicates the total amount of maximum bandwidth available on this interface and is specified in kilobits per second (Kbps). | |||||
| CopticsIMIfUnknownMulticastTrafficLimit | 1.3.6.1.4.1.637.54.1.1.5.1.19.1.37 | Gauge32 | RW | ||
column · Gauge32 · read-write · current This attribute carries out 'on per port basis' ingress admitted unknown multicast rate (the threshold value of unknown multicast traffic rate as admitted on this ingress interface) and is specified in Kilobits per second (Kbps). This value is requested to trigger discarding of NE generated unknown mulitcast traffic rate on this ingress interface and is minor or equal to that specified in ifSpeed for this interface. Disabled unknown multicast limitation is the default value. | |||||
| CopticsIMPortCapabilityIndex | 1.3.6.1.4.1.637.54.1.1.5.1.19.1.38 | Integer32 | RW | ||
column · Integer32 · read-write · current This attribute is a pointer to capability profile entries having opticsIMCapabilityProfileProfIndex equal to opticsIMPortCapabilityIndex. The opticsIMCapabilityProfileTable contains information about capabilities supported by this interface. Default value is zero to indicate no capability profile is referenced. | |||||
| CopticsIMIfSwitchId | 1.3.6.1.4.1.637.54.1.1.5.1.19.1.39 | INTEGER | RW | ||
column · INTEGER · read-write · current This attribute specifies the Ethernet Switch Instance this port belongs to . | |||||
| CopticsIMIfUserLabel | 1.3.6.1.4.1.637.54.1.1.5.1.19.1.40 | OpticsIMUserLabel | RW | ||
column · OpticsIMUserLabel · read-write · current A textual string containing an Label provided by operator for this Interface. | |||||
| CopticsIMIfPortAlarmAdmin | 1.3.6.1.4.1.637.54.1.1.5.1.19.1.41 | INTEGER | RW | ||
column · INTEGER · read-write · current opticsIMIfPortAlarmAdmin specifies 'on per port basis' Port Alarm Admin value
according to below admitted values:
- ne-def: 'on per NE basis' Alarm Admim Value (Default value)
- mon: this Port Alarm Admin value takes as effect the ASAP is considered:
the alarms emitted by that port are handled according to the pointed ASAP object
- auto: this Port Alarm Admin value takes as effect the ASAP (associated to that port)
to be ignored: the alarms emitted by that port are inhibited independently
on the pointed ASAP object (via tsdimIfAsapIndex).
| |||||
| CopticsIMIfIpIntfPointer | 1.3.6.1.4.1.637.54.1.1.5.1.19.1.42 | Unsigned32 (0..2147483647) | RW | ||
column · Unsigned32 (0..2147483647) · read-write · current the reference pointer of opticsIMVrfIpIntf index. The value 0 means that the interface is not IP. Value 0 is the default value | |||||
| CopticsIMIfAlarmReeval | 1.3.6.1.4.1.637.54.1.1.5.1.19.1.43 | TruthValue | RW | ||
column · TruthValue · read-write · current This attribute triggers the interface alarm reevaluation. When this object is set to True the presence of the alarm is reconsidered, starting in any case from a not alarmed status. If the alarm conditions are matched then the alarm is raised, if it was already present the alarm shall be maintained. Default value is False. | |||||
| CopticsIMIflnkaggThreshold | 1.3.6.1.4.1.637.54.1.1.5.1.19.1.44 | INTEGER | RW | ||
column · INTEGER · read-write · current Number of links considered in the detection of the LAG Excessive Bandwidth Degrade (dLAGEXBD) defect: if the number of LAG links, which are both attached from LACP perspective and working (i.e. not in failure condition), is lower than the opticsIMIflnkaggThreshold value and > 0 then the dLAGEXBD is detected. The value of this object is meaningful only in case of LAG ifType. Default value: 1 | |||||
| CopticsIMIf1588TCStatus | 1.3.6.1.4.1.637.54.1.1.5.1.19.1.45 | INTEGER | RO | ||
column · INTEGER · read-only · current This object contains the status of the 1588 Transparent Clock management related the this interface's entry. The Transparent Clock is activated on 'NE basis' but each interface could be in a different status. The 'notApplicable' value is returned when the interface doesn't support the management of the 1588 TC. The 'active' value is returned when the interface is supporting the 1588 TC and the feature is actualy working on. The 'notActive' value is returned when the interface is supporting the 1588 TC but the feature is not working due to some temporary conditions.
| |||||
| !tsdimAlarmPlmRaise | 1.3.6.1.4.1.637.54.1.1.5.1.20 | ||||
notification · current This notification reports the Payload Mismatch (PLM) defect. | |||||
| !tsdimAlarmPlmClear | 1.3.6.1.4.1.637.54.1.1.5.1.21 | ||||
notification · current This notification reports the Payload Mismatch (PLM) defect clear. | |||||
| TopticsIMSdhIfTable | 1.3.6.1.4.1.637.54.1.1.5.1.22 | NA | |||
table · not-accessible · current This table contains the configuration of the server TTP. At startup or when a server TTP is deleted the objects assume the default value. | |||||
| RopticsIMSdhIfEntry | 1.3.6.1.4.1.637.54.1.1.5.1.22.1 | NA | |||
row · not-accessible · current
| |||||
| CopticsIMSdhIfSpeed | 1.3.6.1.4.1.637.54.1.1.5.1.22.1.1 | Gauge32 | RO | ||
column · Gauge32 · read-only · current Value of ifSpeed of the relative server TTP. The value 0 is the default. The change of this object is notified by an Attribute Value Change (AVC) Notification. The value can be expressed in bit/s or kbit/s NE dependent. | |||||
| CopticsIMSdhIfUnderlieLayer | 1.3.6.1.4.1.637.54.1.1.5.1.22.1.2 | INTEGER | RO | ||
column · INTEGER · read-only · current Type of the relative server TTP (SDH or PDH). The value none is the default. The change of this object is notified by an Attribute Value Change (AVC) Notification.
| |||||
| CopticsIMSdhIfType | 1.3.6.1.4.1.637.54.1.1.5.1.22.1.3 | IANAifType | RO | ||
column · IANAifType · read-only · current Type of the interface associated with the server TTP. The value other (1) is the default and applies when no interface type is associated with the server TTP. The change of this object is notified by an Attribute Value Change Notification. | |||||
| CopticsIMSdhIfVcType | 1.3.6.1.4.1.637.54.1.1.5.1.22.1.4 | INTEGER | RO | ||
column · INTEGER · read-only · current Type of the underlying SDH VC. The value other (1) is the default and applies to the case where the underlying layer is not SDH/SONET/PDH or PCONC. The other values (vc12,vc3,vc4,vc4-4c) apply only when the underlying layer is SDH or PCONC. The values (vt1-5, sts-1, sts-3c, sts-12c, sts-192c, vt-2, vt-3, vt-6 ) are applicable when the underlying layer is SONET or PCONC. The values (pdh-e1, pdh-ds1, pdh-e3, pdh-ds3 ) are applicable are applicable when the underlying layer is PDH or PCONC. The change of this object is notified by an Attribute Value Change Notification.
| |||||
| CopticsIMSdhIfCurrSpeed | 1.3.6.1.4.1.637.54.1.1.5.1.22.1.5 | Gauge32 | RO | ||
column · Gauge32 · read-only · current Value of actual ifSpeed of the relative server TTP. The value of the opticsIMSdhIfSpeed is the default. When the underlying layer is PCONC or VCONC it represents the number of active and working VCs in the virtual or packet concatenated Group and therefore it could be lower than the opticsIMSdhIfSpeed. The change of this object is notified by an Attribute Value Change (AVC) Notification. The value can be expressed in bit/s or kbit/s NE dependent | |||||
| !tsdimAlarmTsfRaise | 1.3.6.1.4.1.637.54.1.1.5.1.23 | ||||
notification · current This notification reports TSF alarm. | |||||
| !tsdimAlarmTsfClear | 1.3.6.1.4.1.637.54.1.1.5.1.24 | ||||
notification · current This notification reports TSF alarm clear. | |||||
| StsdimInfoModelVersionMajor | 1.3.6.1.4.1.637.54.1.1.5.1.25 | Integer32 | RO | ||
scalar · Integer32 · read-only · current This is the infomodel major version value. | |||||
| StsdimInfoModelVersionMinor | 1.3.6.1.4.1.637.54.1.1.5.1.26 | Integer32 | RO | ||
scalar · Integer32 · read-only · current This is the infomodel minor version value | |||||
| StsdimInfoModelVersionMaintenance | 1.3.6.1.4.1.637.54.1.1.5.1.27 | DisplayString | RO | ||
scalar · DisplayString · read-only · current This is the infomodel maintenance version value | |||||
| NopticsIMNeConfiguration | 1.3.6.1.4.1.637.54.1.1.5.1.28 | ||||
| SopticsIMNeConfigurationType | 1.3.6.1.4.1.637.54.1.1.5.1.28.1 | DisplayString | RO | ||
scalar · DisplayString · read-only · current This object defines the NE configuration type requested by the managing system. | |||||
| SopticsIMNeConfigurationTypeId | 1.3.6.1.4.1.637.54.1.1.5.1.28.2 | Integer32 | RW | ||
scalar · Integer32 · read-write · current This object defines the identifier of the NE configuration type requested by the managing system. This identifier must be included in one of the entries of the opticsIMAllowedNeConfigurationTypeTable. As a side effect of setting this object, the agent must set the opticsIMNeConfigurationType object with the string associated to this identifier. | |||||
| TopticsIMAllowedNeConfigurationTypeTable | 1.3.6.1.4.1.637.54.1.1.5.1.28.3 | NA | |||
table · not-accessible · current This table contains all the configurations types allowed for the supported NE. | |||||
| RopticsIMAllowedNeConfigurationTypeEntry | 1.3.6.1.4.1.637.54.1.1.5.1.28.3.1 | NA | |||
row · not-accessible · current An entry of the allowed Ne configuration types table. Each entry (row) corresponds to a configuration type allowed for the NE. | |||||
| CopticsIMAllowedNeConfigurationId | 1.3.6.1.4.1.637.54.1.1.5.1.28.3.1.1 | Integer32 | NA | ||
column · Integer32 · not-accessible · current This object contains the identifier associated to a NE configuration type. It identifies the index of the table. | |||||
| CopticsIMAllowedNeConfigurationType | 1.3.6.1.4.1.637.54.1.1.5.1.28.3.1.2 | DisplayString | RO | ||
column · DisplayString · read-only · current This object identifies an allowed configuration type of the NE. | |||||
| SopticsIMMarket | 1.3.6.1.4.1.637.54.1.1.5.1.28.4 | INTEGER | RW | ||
scalar · INTEGER · read-write · current This object specifies the application market. With this information the agent will be able to provide to the manager only the configurations consistent with the market defined.
| |||||
| SopticsIMNeEquipmentName | 1.3.6.1.4.1.637.54.1.1.5.1.28.5 | DisplayString | RO | ||
scalar · DisplayString · read-only · current This scalar object defines in synthesis the NE characteristics (NE name, frequency, configuration type, modulation,capability...) | |||||
| TopticsIMAllowedNePeripheralTable | 1.3.6.1.4.1.637.54.1.1.5.1.28.6 | NA | |||
table · not-accessible · current This table contains all the peripherals (type and configuration) allowed for each configuration Ne allowed on the NE. | |||||
| RopticsIMAllowedNePeripheralEntry | 1.3.6.1.4.1.637.54.1.1.5.1.28.6.1 | NA | |||
row · not-accessible · current An entry of the allowed NE peripherals table. Each entry (row) corresponds to an allowed peripheral type and peripheral configuration for each configuration type Ne allowed for the NE | |||||
| CopticsIMAllowedNePeripheralId | 1.3.6.1.4.1.637.54.1.1.5.1.28.6.1.1 | Integer32 | NA | ||
column · Integer32 · not-accessible · current This object contains the identifier associated to a peripheral type and peripheral configuration. It identifies the index of the table. | |||||
| CopticsIMAllowedNePeripheralType | 1.3.6.1.4.1.637.54.1.1.5.1.28.6.1.2 | DisplayString | RO | ||
column · DisplayString · read-only · current This object identifies an allowed peripheral type. | |||||
| CopticsIMAllowedNePeripheralConfiguration | 1.3.6.1.4.1.637.54.1.1.5.1.28.6.1.3 | DisplayString | RO | ||
column · DisplayString · read-only · current This object identifies an allowed configuration type of the peripheral. | |||||
| TopticsIMNeTrsDirectionTable | 1.3.6.1.4.1.637.54.1.1.5.1.28.7 | NA | |||
table · not-accessible · current This table contains the parameters associated to the transmission directions on NE. A transmission direction connects the NE to an adjacent NE by a specific transmission interface (i.e. radio, PDH) | |||||
| RopticsIMNeTrsDirectionEntry | 1.3.6.1.4.1.637.54.1.1.5.1.28.7.1 | NA | |||
row · not-accessible · current An entry of the direction table. Each entry (row) corresponds to a specific direction. | |||||
| CopticsIMNeTrsDirectionIndex | 1.3.6.1.4.1.637.54.1.1.5.1.28.7.1.1 | Integer32 | NA | ||
column · Integer32 · not-accessible · current This object contains the identifier associated to a transmission direction to/from an adjacent NE. It identifies the index of the table. | |||||
| CopticsIMNeTrsDirectionConfigurationId | 1.3.6.1.4.1.637.54.1.1.5.1.28.7.1.2 | Integer32 | RC | ||
column · Integer32 · read-create · current This object defines the identifier of the NE configuration type requested by the managing system on this direction. Thid identifier must be included in one of the entries of the opticsIMAllowedNeConfigurationTypeTable. | |||||
| CopticsIMNeTrsDirectionMaxCapacity | 1.3.6.1.4.1.637.54.1.1.5.1.28.7.1.3 | DisplayString | RO | ||
column · DisplayString · read-only · current This object contains the maximum transmission capacity on this direction. It is updated by managed system (agent) after configuration of transmission capacity for each interface (i.e. radio, PDH on each specific object) belonging to this direction. | |||||
| CopticsIMNeTrsDirectionRole | 1.3.6.1.4.1.637.54.1.1.5.1.28.7.1.4 | DisplayString | RC | ||
column · DisplayString · read-create · current This object reports a specific behaviour for this direction. It is used to differ the behaviour of this direction from the behaviour of the other directions. The content is defined in each product specification. | |||||
| CopticsIMNeTrsDirectionRowStatus | 1.3.6.1.4.1.637.54.1.1.5.1.28.7.1.5 | RowStatus | RC | ||
column · RowStatus · read-create · current See textual convention. | |||||
| TopticsIMNeDirectionPeripheralTable | 1.3.6.1.4.1.637.54.1.1.5.1.28.8 | NA | |||
table · not-accessible · current This table contains all the peripheral (type and configuration) selected for each direction on the NE. | |||||
| RopticsIMNeDirectionPeripheralEntry | 1.3.6.1.4.1.637.54.1.1.5.1.28.8.1 | NA | |||
row · not-accessible · current An entry of direction table. Each entry (row) corresponds to a selected peripheralId for each direction | |||||
| CopticsIMNeDirectionPeripheralIndex | 1.3.6.1.4.1.637.54.1.1.5.1.28.8.1.1 | Integer32 | NA | ||
column · Integer32 · not-accessible · current This object contains the index of a peripheral identifier selected on a direction. It identifies the index of the table. | |||||
| CopticsIMNeDirectionPeripheralId | 1.3.6.1.4.1.637.54.1.1.5.1.28.8.1.2 | Integer32 | RC | ||
column · Integer32 · read-create · current This object defines the identifier of the peripheral type and peripheral configuration requested by the managing systems. This identifier must be included in one of the opticsIMAllowedNePeripheralTable associated to the opticsIMNeTrsDirectionConfigurationId object on opticsIMNeTrsDirectionTable. As a side effect of setting this object, the agent must set the opticsIMNeDirectionPeripheralType object and the opticsIMNeDirectionPeripheralConfiguration object with the strings associated. | |||||
| CopticsIMNeDirectionPeripheralType | 1.3.6.1.4.1.637.54.1.1.5.1.28.8.1.3 | DisplayString | RO | ||
column · DisplayString · read-only · current This object defines a pheripheral type requested by the managing system on a direction. | |||||
| CopticsIMNeDirectionPeripheralConfiguration | 1.3.6.1.4.1.637.54.1.1.5.1.28.8.1.4 | DisplayString | RC | ||
column · DisplayString · read-create · current This object defines a pheripheral configuration requested by the managing system on a direction. | |||||
| CopticsIMNeDirectionPeripheralRowStatus | 1.3.6.1.4.1.637.54.1.1.5.1.28.8.1.5 | RowStatus | RC | ||
column · RowStatus · read-create · current See textual convention. | |||||
| TopticsIMNeCompositionTable | 1.3.6.1.4.1.637.54.1.1.5.1.28.9 | NA | |||
table · not-accessible · current This table contains the composition of the NE in term of NE configuration type requested by the managing system. | |||||
| RopticsIMNeCompositionEntry | 1.3.6.1.4.1.637.54.1.1.5.1.28.9.1 | NA | |||
row · not-accessible · current An entry of the NE composition table. Each entry (row) corresponds to a configuration type allowed for the NE. | |||||
| CopticsIMNeCompositionIndex | 1.3.6.1.4.1.637.54.1.1.5.1.28.9.1.1 | Integer32 | NA | ||
column · Integer32 · not-accessible · current This object contains the index of the table. | |||||
| CopticsIMNeCompositionConfigurationId | 1.3.6.1.4.1.637.54.1.1.5.1.28.9.1.2 | Integer32 | RC | ||
column · Integer32 · read-create · current This object defines a identifier of the NE configuration type requested by the managing system. This identifier must be included in one of the entries of the opticsIMAllowedNEConfigurationTypeTable. As a side effect of this setting, the agent must set the opticsIMNeCompositionConfigurationType object with the string associated to this identifier. | |||||
| CopticsIMNeCompositionConfigurationType | 1.3.6.1.4.1.637.54.1.1.5.1.28.9.1.3 | DisplayString | RO | ||
column · DisplayString · read-only · current This object defines a NE configuration type requested by the managing system. | |||||
| CopticsIMNeCompositionRowStatus | 1.3.6.1.4.1.637.54.1.1.5.1.28.9.1.4 | RowStatus | RC | ||
column · RowStatus · read-create · current See textual convention. | |||||
| SopticsIMNeCompositionIndexNext | 1.3.6.1.4.1.637.54.1.1.5.1.28.10 | Unsigned32 (0..2147483647) | RO | ||
scalar · Unsigned32 (0..2147483647) · read-only · current This object contains an appropriate value to be used for opticsIMNeCompositionIndex when creating entries in the opticsIMNeCompositionTable. The value 0 indicates that no unassigned entries are available. To obtain the opticsIMNeCompositionIndex value for a new entry, the manager issues a management protocol retrieval operation to obtain the current value of this object. After each retrieval, the agent should modify the value to the next unassigned index. After a manager retrieves a value, the agent will determine through its local policy when this index value will be made available for reuse. | |||||
| SopticsIMProtectionIndexNext | 1.3.6.1.4.1.637.54.1.1.5.1.28.11 | Unsigned32 (0..2147483647) | RO | ||
scalar · Unsigned32 (0..2147483647) · read-only · current This object contains an appropriate value to be used for opticsIMProtectionConfigurationIndex when creating entries in the opticsIMProtectionConfigurationTable. The value 0 indicates that no unassigned entries are available. To obtain the opticsIMProtectionConfigurationIndex value for a new entry, the manager issues a management protocol retrieval operation to obtain the current value of this object. After each retrieval, the agent should modify the value to the next unassigned index. After a manager retrieves a value, the agent will determine through its local policy when this index value will be made available for reuse. | |||||
| TopticsIMProtectionConfigurationTable | 1.3.6.1.4.1.637.54.1.1.5.1.28.12 | NA | |||
table · not-accessible · current This table allows the managing system to define the protection type on equipment provisioning in order to create the protection schemes. It is indexed by the equipment position, related to equipmentTable, involved in the protection scheme | |||||
| RopticsIMProtectionConfigurationEntry | 1.3.6.1.4.1.637.54.1.1.5.1.28.12.1 | NA | |||
row · not-accessible · current An entry of the protection configuration table. Each entry (row) corresponds to a Protection type involving 2 equipment position on equipmentTable. | |||||
| CopticsIMProtectionConfigurationIndex | 1.3.6.1.4.1.637.54.1.1.5.1.28.12.1.1 | Unsigned32 | NA | ||
column · Unsigned32 · not-accessible · current This object contains the index of the table. It contains the value retrieved from agent by a GET request on opticsIMProtectionIndexNext object. | |||||
| CopticsIMProtectionEqptPositionMain | 1.3.6.1.4.1.637.54.1.1.5.1.28.12.1.2 | OCTET STRING (SIZE (4)) | RC | ||
column · OCTET STRING (SIZE (4)) · read-create · current This object contains the index of the table. It contains the same value of equipmentPosition index on OpticsIMEquipmentEntry that the managing system requires involved in a protection scheme. | |||||
| CopticsIMProtectionEqptPositionSpare | 1.3.6.1.4.1.637.54.1.1.5.1.28.12.1.3 | OCTET STRING (SIZE (4)) | RC | ||
column · OCTET STRING (SIZE (4)) · read-create · current This object contains the index of the table. It contains the same value of equipmentPosition index on OpticsIMEquipmentEntry that the managing system requires involved in a protection scheme. | |||||
| CopticsIMProtectionType | 1.3.6.1.4.1.637.54.1.1.5.1.28.12.1.4 | DisplayString | RC | ||
column · DisplayString · read-create · current This object defines the protection for the equipment related to this postion. | |||||
| CopticsIMProtectionRowStatus | 1.3.6.1.4.1.637.54.1.1.5.1.28.12.1.5 | RowStatus | RC | ||
column · RowStatus · read-create · current See textual convention. | |||||
| CopticsIMProtectionTypeId | 1.3.6.1.4.1.637.54.1.1.5.1.28.12.1.6 | Integer32 | RC | ||
column · Integer32 · read-create · current This object contains the identifier of the protection type related to opticsIMProtectionEqptPositionMain and opticsIMProtectionEqptPositionSpare requested by the managing systems. The identifier must be included in one of the entries of the opticsIMAllowedProtectionTypesTable associated to the equipmentExpected for the opticsIMProtectionEqptPositionMain and opticsIMProtectionEqptPositionSpare. As a side effect of setting this object, the agent must set the opticsIMProtectionType object with the string associated to this identifier (see opticsIMAllowedprotectionTypesTable). | |||||
| TopticsIMAllowedProtectionTypesTable | 1.3.6.1.4.1.637.54.1.1.5.1.28.13 | NA | |||
table · not-accessible · current This table contains, for each equipment type allowed in the NE, the allowed protection types. | |||||
| RopticsIMAllowedProtectionTypesEntry | 1.3.6.1.4.1.637.54.1.1.5.1.28.13.1 | NA | |||
row · not-accessible · current An entry of the allowed protection type table. Each entry (row) corresponds to an protection type allowed for the equipment type identified by the equipmentType object. | |||||
| CequipmentType | 1.3.6.1.4.1.637.54.1.1.5.1.28.13.1.1 | DisplayString | NA | ||
column · DisplayString · not-accessible · current This object contains an equipment type allowed on the NE. | |||||
| CallowedProtectionTypeId | 1.3.6.1.4.1.637.54.1.1.5.1.28.13.1.2 | Integer32 | NA | ||
column · Integer32 · not-accessible · current This object contains the identifier of an protection type allowed for the associated equipment type. | |||||
| CallowedProtectionType | 1.3.6.1.4.1.637.54.1.1.5.1.28.13.1.3 | DisplayString | RO | ||
column · DisplayString · read-only · current This object identifies the protection type (string) associated to the allowedProtectionTypeId. | |||||
| SopticsIMTopologyGroup | 1.3.6.1.4.1.637.54.1.1.5.1.28.14 | Integer32 | RW | ||
scalar · Integer32 · read-write · current This object identifies the group that the NE belong to. A Service could be created on NEs belonging to the same group. | |||||
| SopticsIMExternalTime | 1.3.6.1.4.1.637.54.1.1.5.1.29 | DateAndTime | RW | ||
scalar · DateAndTime · read-write · current This object specifies the current time of the NE. This time has to be used as reference for all time stamp activities in the NE. | |||||
| NopticsIMNTPManagement | 1.3.6.1.4.1.637.54.1.1.5.1.30 | ||||
| SopticsIMNTPStatus | 1.3.6.1.4.1.637.54.1.1.5.1.30.1 | INTEGER | RW | ||
scalar · INTEGER · read-write · current This object is used to enable/disable the Network Time Protocol (NTP).
| |||||
| SopticsIMMainNTPServerAddress | 1.3.6.1.4.1.637.54.1.1.5.1.30.2 | IpAddress | RW | ||
scalar · IpAddress · read-write · current This object contains the address of the main server of the Network Time Protocol (NTP). | |||||
| SopticsIMSpareNTPServerAddress | 1.3.6.1.4.1.637.54.1.1.5.1.30.3 | IpAddress | RW | ||
scalar · IpAddress · read-write · current This object contains the address of the spare server of the Network Time Protocol (NTP). | |||||
| SopticsIMNTPServersReachabilityStatus | 1.3.6.1.4.1.637.54.1.1.5.1.30.4 | INTEGER | RO | ||
scalar · INTEGER · read-only · current This object is used to indicate if the Network Time Protocol (NTP) servers (main and spare) are reachable.
| |||||
| SopticsIMMainNTPServerIPv6Address | 1.3.6.1.4.1.637.54.1.1.5.1.30.62 | InetAddressIPv6 | RW | ||
scalar · InetAddressIPv6 · read-write · current This object contains the address of the main server of the Network Time Protocol (NTP) in the IPv6 format. | |||||
| SopticsIMSpareNTPServerIPv6Address | 1.3.6.1.4.1.637.54.1.1.5.1.30.63 | InetAddressIPv6 | RW | ||
scalar · InetAddressIPv6 · read-write · current This object contains the address of the spare server of the Network Time Protocol (NTP) in the IPv6 format. | |||||
| SopticsimEpsConfStatus | 1.3.6.1.4.1.637.54.1.1.5.1.31 | TruthValue | RO | ||
scalar · TruthValue · read-only · current This object reports information about the EPS (Equipment Protection Switching) configuration of an ISA board. If the ISA board does not support plug-able access card, this object becomes true if and only if the ISA board is EPS protected. If the ISA board supports plug-able access card, this object becomes true if and only if the ISA board is EPS protected and both the main and the spare boards are equipped with the same access card. | |||||
| SopticsimEpsActiveRole | 1.3.6.1.4.1.637.54.1.1.5.1.32 | INTEGER | RO | ||
scalar · INTEGER · read-only · current This object report the role (i.e. main or spare) of the active ISA board. This object is meaningful only if the opticsimEpsConfStatus is true. Otherwise, the value main (1) is always returned.
| |||||
| SopticsimIsaAccess | 1.3.6.1.4.1.637.54.1.1.5.1.33 | Unsigned32 | RO | ||
scalar · Unsigned32 · read-only · current This object report the access card equipped in the Equipment domain for the ISA board. The value 0 (unknown) is the default value for the following cases: - the ISA board does not support equipped access card (e.g. because it is plugged in an old equipment) - the access card in is not known by the ISA board (e.g. it is not a 14xFE nor a 4xGE) The value 1 (none) is used to report that no access card has been equipped. The other values (>1) represent the access card that was equipped. The association between the value of this object and the access card is product specific and will be documented in the product external specification | |||||
| SopticsimMaskNamingRule | 1.3.6.1.4.1.637.54.1.1.5.1.34 | DisplayString | RO | ||
scalar · DisplayString · read-only · current The value of this object provides the mask of the naming of the TTPs. The mask indicates the binary format of the naming composed by the following fields: x for data purposes field, r for rack field, s for subrack field, b for board field, d for drawer field, p for port field, c for channel field. The mask allows the decoding of the naming, specifying for each field (all the fields are present and in the above listed order) the number of reserved bits followed by the character (above provided) that identifies the field itself. In case a field is never used inside the NE, the field is anyway present with number of reserved bits 0 (e.g. if the drawer is never used an example of mask is 4x3r3s10b0d10p2c). | |||||
| SopticsimSwPackageProfile | 1.3.6.1.4.1.637.54.1.1.5.1.35 | Bits | RO | ||
scalar · Bits · read-only · current This object is used for reporting the software package profile which indicates the network functionalities enabled on the NE. The value of this attribute is commonly agreed, its semantic will be described in the relevant Ext. Interface Management Specification.
| |||||
| SopticsimNeAutoProvisioning | 1.3.6.1.4.1.637.54.1.1.5.1.36 | INTEGER | RW | ||
scalar · INTEGER · read-write · current This object allows the manager to set the way of physical item provisioning on the NE. The Full Plug&Play value will set the automatic provisioning without manager intervention. The No Plug&Play value will set the provisioning full in the hands of manager. The Confirmed Plug&Play value (that is the default value) will cause the agent to ask for manager confirmation before provisioning. The confirmation request to operator by manager (in the confirmed plug and play case), is activated by an Attribute Value Change (AVC) associated to the change of the opticsEquipmentActual object value in the OPTICSIM-EQPT-MIB
| |||||
| NopticsIMNePMCollection | 1.3.6.1.4.1.637.54.1.1.5.1.37 | ||||
| SopticsIMNePMCollectionStatus | 1.3.6.1.4.1.637.54.1.1.5.1.37.1 | INTEGER | RO | ||
scalar · INTEGER · read-only · current This object defines the PM collection NE status: three operating status have been defined: the <Ready_for_Request> status, the <In_Preparation> status, the <fileTransferCompleted> status; the default status is the <fileTransferCompleted> one.
| |||||
| SopticsIMNePMActivateCollection | 1.3.6.1.4.1.637.54.1.1.5.1.37.2 | INTEGER | RW | ||
scalar · INTEGER · read-write · current This object defines the start of the PM collection on the NE: the value <NormalStart> can be set by manager when he want to activate the PM collection in normal condition; the value <ForcedStart> can be set by manager when he want to activate the PM collection in abnormal condition (for instance when NE is still preparing a previous commanded PM collection); the agent will reset the value to <Noop> when the manager setting has been recognized. The default value is the <Noop> one.
| |||||
| SopticsIMNePMTimePeriodCollection | 1.3.6.1.4.1.637.54.1.1.5.1.37.3 | OpticsIMPmPeriodTime | RW | ||
scalar · OpticsIMPmPeriodTime · read-write · current This object defines the time value before which no hystorical data must be considered for the PM collection file. The default value, that is the null value (i.e. 0), represents the maximum allowed for that application. | |||||
| SopticsIMMibConfigurationMode | 1.3.6.1.4.1.637.54.1.1.5.1.38 | OpticsIMMibConfigurationMode | RW | ||
scalar · OpticsIMMibConfigurationMode · read-write · current This attribute defines the possibility to 'isolate' (offline) the MIB configuration from the HW Configuration inside the NE. This means both that, at the management interface, requests are not propagated to the HW and alarms are not reported. Default value (online) can be changed only in case of MIB Restore procedure. | |||||
| TopticsIMMngInterfaceListTable | 1.3.6.1.4.1.637.54.1.1.5.1.39 | NA | |||
table · not-accessible · current This table defines the list of management Interfaces with: management
interface type, address and its charaterization.
The address allows reaching the NE applications (Agents) in charge of the
specific management interface.
In case of SNMP Agent, where for the address an ASN.1 Octect String is
simply defined, this string, aligned to SNMPv2-SMI, has to be composed as
follows: IpAddress:PortNumber.
In case of Q3 Agent, a presentation address consists of octect strings
with:
- presentation selector, session selector, transport selector and a set
of network addresses as defined in RFC 1278.
The characterization defines the primary and secondary management
interfaces.
Primary is the management interface where basic functionalities, like
Equipment, LAC, NTP, File Transfer, etc. are accessible. | |||||
| RopticsIMMngInterfaceListEntry | 1.3.6.1.4.1.637.54.1.1.5.1.39.1 | NA | |||
row · not-accessible · current see description of opticsIMMngInterfaceListTable | |||||
| CopticsIMMngInterfaceListIndex | 1.3.6.1.4.1.637.54.1.1.5.1.39.1.1 | INTEGER | NA | ||
column · INTEGER · not-accessible · current Index of opticsIMMngInterfaceListEntry | |||||
| CopticsIMMngInterfaceType | 1.3.6.1.4.1.637.54.1.1.5.1.39.1.2 | OpticsIMMngInterfaceType | RO | ||
column · OpticsIMMngInterfaceType · read-only · current It defines the type of the management interface. | |||||
| CopticsIMMngInterfaceCharacterization | 1.3.6.1.4.1.637.54.1.1.5.1.39.1.3 | OpticsIMMngInterfaceCharacterization | RO | ||
column · OpticsIMMngInterfaceCharacterization · read-only · current The characterization defines the primary and secondary management interfaces. Primary is the management interface where basic functionalities, like Equipment, LAC, NTP, File Transfer, etc. are accessible. | |||||
| CopticsIMMngInterfaceAddressType | 1.3.6.1.4.1.637.54.1.1.5.1.39.1.4 | OpticsIMMngInterfaceAddressType | RO | ||
column · OpticsIMMngInterfaceAddressType · read-only · current It defines the address type of the management interface. | |||||
| CopticsIMMngInterfaceAddress | 1.3.6.1.4.1.637.54.1.1.5.1.39.1.5 | DisplayString | RO | ||
column · DisplayString · read-only · current It defines the address associated to the management interface. In case of Ip Address DisplayString is encoded aligned to SNMPv2-SMI, in case of Presentation Address DisplayString is encoded aligned to RFC 1278. | |||||
| CopticsIMMngInterfaceAdminState | 1.3.6.1.4.1.637.54.1.1.5.1.39.1.6 | INTEGER | RW | ||
column · INTEGER · read-write · current It defines the administrative state of the management interface. When this object is set to 'disable' value then the NE is not allowed to be supervised from this management interface.
| |||||
| NopticsIMCommonAlarms | 1.3.6.1.4.1.637.54.1.1.5.1.40 | ||||
| !opticsIMAlarmLossOfSignalRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.1 | ||||
notification · current This notification reports the Loss Of Signal (LOS) defect raise. | |||||
| !opticsIMAlarmLossOfSignalClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.2 | ||||
notification · current This notification reports the Loss Of Signal (LOS) defect clear. | |||||
| !opticsIMAlarmLossOfFrameRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.3 | ||||
notification · current This notification reports the Loss Of Frame (LOF) defect raise. | |||||
| !opticsIMAlarmLossOfFrameClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.4 | ||||
notification · current This notification reports the Loss Of Frame (LOF) defect clear. | |||||
| !opticsIMAlarmAisRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.5 | ||||
notification · current This notification reports the AIS defect raise. | |||||
| !opticsIMAlarmAisClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.6 | ||||
notification · current This notification reports the AIS defect clear. | |||||
| !opticsIMAlarmTransmitterFailureRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.7 | ||||
notification · current This notification reports the Transmitter Failure (TF) defect raise. | |||||
| !opticsIMAlarmTransmitterFailureClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.8 | ||||
notification · current This notification reports the Transmitter Failure (TF) defect clear. | |||||
| !opticsIMAlarmTransmitterDegradedRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.9 | ||||
notification · current This notification reports the Transmitter Degraded (TD) defect raise. | |||||
| !opticsIMAlarmTransmitterDegradedClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.10 | ||||
notification · current This notification reports the Transmitter Degraded (TD) defect clear. | |||||
| !opticsIMAlarmRemoteDefectIndicationRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.11 | ||||
notification · current This notification reports the Remote Defect Indication (RDI) defect raise. | |||||
| !opticsIMAlarmRemoteDefectIndicationClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.12 | ||||
notification · current This notification reports the Remote Defect Indication (RDI) defect clear. | |||||
| !opticsIMAlarmCableLOSRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.13 | ||||
notification · current This notification reports the Cable LOS defect raise. | |||||
| !opticsIMAlarmCableLOSClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.14 | ||||
notification · current This notification reports the Cable LOS defect clear. | |||||
| !opticsIMAlarmRxLOSRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.15 | ||||
notification · current This notification reports the rxLOS (LOS of the incoming signal for the Rx subfunction) defect raise. | |||||
| !opticsIMAlarmRxLOSClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.16 | ||||
notification · current This notification reports the rxLOS (LOS of the incoming signal for the Rx subfunction) defect clear. | |||||
| !opticsIMAlarmRxFailRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.17 | ||||
notification · current This notification reports the rxFail (a fail of the Rx subfunction) defect raise. | |||||
| !opticsIMAlarmRxFailClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.18 | ||||
notification · current This notification reports the rxFail (a fail of the Rx subfunction) defect clear. | |||||
| !opticsIMAlarmDemLOSRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.19 | ||||
notification · current This notification reports the demLOS (LOS of the incoming signal for the demodulation subfunction) defect raise. | |||||
| !opticsIMAlarmDemLOSClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.20 | ||||
notification · current This notification reports the demLOS (LOS of the incoming signal for the demodulation subfunction) defect clear. | |||||
| !opticsIMAlarmDemFailRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.21 | ||||
notification · current This notification reports the demFail (a fail of the demodulation subfunction) defect raise. | |||||
| !opticsIMAlarmDemFailClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.22 | ||||
notification · current This notification reports the DemFail (a fail of the demodulation subfunction) defect clear. | |||||
| !opticsIMAlarmModLOSRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.23 | ||||
notification · current This notification reports the modLOS (LOS of the incoming signal for the modulation subfunction) defect raise. | |||||
| !opticsIMAlarmModLOSClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.24 | ||||
notification · current This notification reports the modLOS (LOS of the incoming signal for the modulation subfunction) defect clear. | |||||
| !opticsIMAlarmModFailRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.25 | ||||
notification · current This notification reports the modFail (a fail of the modulation subfunction) defect raise. | |||||
| !opticsIMAlarmModFailClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.26 | ||||
notification · current This notification reports the modFail (a fail of the modulation subfunction) defect clear. | |||||
| !opticsIMAlarmTxLOSRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.27 | ||||
notification · current This notification reports the txLOS (LOS of the incoming signal for the Tx subfunction) defect raise. | |||||
| !opticsIMAlarmTxLOSClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.28 | ||||
notification · current This notification reports the txLOS (LOS of the incoming signal for the Tx subfunction) defect clear. | |||||
| !opticsIMAlarmTxFailRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.29 | ||||
notification · current This notification reports the txFail (a fail of the Tx subfunction) defect raise. | |||||
| !opticsIMAlarmTxFailClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.30 | ||||
notification · current This notification reports the txFail (a fail of the Tx subfunction) defect clear. | |||||
| !opticsIMAlarmTCARaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.31 | ||||
notification · current This notification reports the Threshold Crossing Alarm defect raise. | |||||
| !opticsIMAlarmTCAClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.32 | ||||
notification · current This notification reports the Threshold Crossing Alarm defect clear. | |||||
| !opticsIMAlarmUnavailableTimeRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.33 | ||||
notification · current This notification reports the Unavailable Time defect raise. | |||||
| !opticsIMAlarmUnavailableTimeClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.34 | ||||
notification · current This notification reports the Unavailable Time defect clear. | |||||
| !opticsIMAlarmTsfRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.35 | ||||
notification · current This notification reports the Trail Signal Fail TSF) alarm. It does not apply to ATM interfaces where the tsdimAlarmTsfRaise notification is used. | |||||
| !opticsIMAlarmTsfClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.36 | ||||
notification · current This notification reports the Trail Signal Fail (TSF) alarm clear. It does not apply to ATM interfaces where the tsdimAlarmTsfClear notification is used. | |||||
| !opticsIMAlarmPlmRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.37 | ||||
notification · current This notification reports the Payload Mismatch (PLM) alarm. It does not apply to ATM interfaces where the tsdimAlarmPlmRaise notification is used. | |||||
| !opticsIMAlarmPlmClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.38 | ||||
notification · current This notification reports the Payload Mismatch (PLM) alarm clear. It does not apply to ATM interfaces where the tsdimAlarmPlmClear notification is used. | |||||
| !opticsIMAlarmUruRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.39 | ||||
notification · current This notification reports the Underline Resource Unavailable (URU) defect raise. | |||||
| !opticsIMAlarmUruClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.40 | ||||
notification · current This notification reports the Underline Resource Unavailable (URU) defect clear. | |||||
| !opticsIMAlarmLAPDFailRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.41 | ||||
notification · current This notification reports the LAPD Fail defect raise. | |||||
| !opticsIMAlarmLAPDFailClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.42 | ||||
notification · current This notification reports the LAPD Fail defect clear. | |||||
| !opticsimGfpAlarmGtmRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.43 | ||||
notification · current This notification reports the GFP Type Mismatch (GTM) alarm. | |||||
| !opticsimGfpAlarmGtmClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.44 | ||||
notification · current This notification reports the GFP Type Mismatch (GTM) alarm clear. | |||||
| !opticsimDAAlarmDACMRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.45 | ||||
notification · current This notification reports the Loss of DACM alarm. | |||||
| !opticsimDAAlarmDACMClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.46 | ||||
notification · current This notification reports the Loss of DACM alarm clear. | |||||
| !opticsIMAlarmLossOfAlignmentRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.47 | ||||
notification · current This notification reports the Loss of Alignment defect raise. | |||||
| !opticsIMAlarmLossOfAlignmentClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.48 | ||||
notification · current This notification reports the Loss of Alignment defect clear. | |||||
| !opticsIMAlarmPPPFailRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.49 | ||||
notification · current This notification reports the Point to Point IP Fail defect raise. | |||||
| !opticsIMAlarmPPPFailClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.50 | ||||
notification · current This notification reports the Point to Point IP Fail defect clear. | |||||
| !opticsIMAlarmRemoteNEFailureRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.51 | ||||
notification · current This notification reports the Remote NE Failure defect raise. | |||||
| !opticsIMAlarmRemoteNEFailureClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.52 | ||||
notification · current This notification reports the Remote NE Failure defect clear. | |||||
| !opticsimSdhConcDegradeRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.53 | ||||
notification · current This notification reports that at least one active VC in a virtual or packet concatenated group is not working and therefore the opticsIMSdhIfCurrSpeed is lower than the nominal opticsIMSdhIfSpeed. | |||||
| !opticsimSdhConcDegradeClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.54 | ||||
notification · current This notification reports the all the active VCs in a virtual or packet concatenated group are working. | |||||
| !opticsimClientSignalFailRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.55 | ||||
notification · current Client Signal Fail raise. | |||||
| !opticsimClientSignalFailClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.56 | ||||
notification · current Client Signal Fail clear. | |||||
| !opticsIMAlarmLossOfPointerRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.57 | ||||
notification · current This notification reports the Loss of Pointer defect raise. | |||||
| !opticsIMAlarmLossOfPointerClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.58 | ||||
notification · current This notification reports the Loss of Pointer defect clear. | |||||
| !opticsIMAlarmLossOfMultiframeRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.59 | ||||
notification · current This notification reports the Loss of Multiframe defect raise. | |||||
| !opticsIMAlarmLossOfMultiframeClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.60 | ||||
notification · current This notification reports the Loss of Multiframe defect clear. | |||||
| !opticsIMAlarmSequenceMismatchRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.61 | ||||
notification · current This notification reports the Sequence mismatch defect raise. | |||||
| !opticsIMAlarmSequenceMismatchClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.62 | ||||
notification · current This notification reports the Sequence mismatch defect clear. | |||||
| !opticsIMAlarmServerSignalFailRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.63 | ||||
notification · current This notification reports the Server Signal Fail raise. | |||||
| !opticsIMAlarmServerSignalFailClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.64 | ||||
notification · current This notification reports the Server Signal Fail clear. | |||||
| !opticsIMAlarmUnequippedRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.65 | ||||
notification · current This notification reports the VC-n unequipped defect raise. | |||||
| !opticsIMAlarmUnequippedClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.66 | ||||
notification · current This notification reports the VC-n unequipped defect clear. | |||||
| !opticsIMAlarmExstensionHeaderMismatchRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.67 | ||||
notification · current This notification reports the Exstension Header Mismatch (EXM) defect raise. | |||||
| !opticsIMAlarmExstensionHeaderMismatchClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.68 | ||||
notification · current This notification reports the Exstension Header Mismatch (EXM) defect clear. | |||||
| !opticsIMAlarmUserPayloadMismatchRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.69 | ||||
notification · current This notification reports the User Payload Mismatch (UPM) defect raise. | |||||
| !opticsIMAlarmUserPayloadMismatchClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.70 | ||||
notification · current This notification reports the User Payload Mismatch (UPM) defect clear. | |||||
| !opticsIMAlarmDegradeRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.71 | ||||
notification · current This notification reports Degraded defect raise. | |||||
| !opticsIMAlarmDegradeClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.72 | ||||
notification · current This notification reports Degraded defect clear. | |||||
| !opticsimAlarmInputPowerDegradeRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.73 | ||||
notification · current This notification reports input power Degraded defect raise. | |||||
| !opticsimAlarmInputPowerDegradeClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.74 | ||||
notification · current This notification reports input power Degraded defect clear. | |||||
| !opticsimAlarmMisconnectionRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.75 | ||||
notification · current This notification reports Misconnection of CESoETH frames defect raise. | |||||
| !opticsimAlarmMisconnectionClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.76 | ||||
notification · current This notification reports Misconnection of CESoETH frames defect clear. | |||||
| !opticsimAlarmLateFramesRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.77 | ||||
notification · current This notification reports Late arriving CESoETH Frames defect raise. | |||||
| !opticsimAlarmLateFramesClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.78 | ||||
notification · current This notification reports Late arriving CESoETH Frames defect clear. | |||||
| !opticsimAlarmMalformedFramesRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.79 | ||||
notification · current This notification reports Malformed Frames defect raise. | |||||
| !opticsimAlarmMalformedFramesClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.80 | ||||
notification · current This notification reports Malformed Frames defect clear. | |||||
| !opticsimAlarmJitterBufferOverrunRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.81 | ||||
notification · current This notification reports the Jitter Buffer Overrun defect raise. | |||||
| !opticsimAlarmJitterBufferOverrunClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.82 | ||||
notification · current This notification reports the Jitter Buffer Overrun defect clear. | |||||
| !opticsimAlarmJitterBufferUnderrunRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.83 | ||||
notification · current This notification reports the Jitter Buffer Underrun defect raise. | |||||
| !opticsimAlarmJitterBufferUnderrunClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.84 | ||||
notification · current This notification reports the Jitter Buffer Underrun defect clear. | |||||
| !opticsimAlarmServerSignalIngrFailRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.85 | ||||
notification · current This notification reports the Server Signal Fail on ingressing raise. | |||||
| !opticsimAlarmServerSignalIngrFailClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.86 | ||||
notification · current This notification reports the Server Signal Fail on ingressing clear. | |||||
| !opticsimAlarmServerSignalEgreFailRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.87 | ||||
notification · current This notification reports the Server Signal Fail on egressing raise. | |||||
| !opticsimAlarmServerSignalEgreFailClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.88 | ||||
notification · current This notification reports the Server Signal Fail on egressing clear. | |||||
| !opticsimAlarmTrafficDisableRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.89 | ||||
notification · current This notification reports the Traffic Disable raise. | |||||
| !opticsimAlarmTrafficDisableClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.90 | ||||
notification · current This notification reports the Traffic disable clear. | |||||
| !opticsimAlarmEthOAMLossOfContinuityRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.91 | ||||
notification · current This notification reports (Ethernet OAM Continuity Check) Loss Of Continuity raise. | |||||
| !opticsimAlarmEthOAMLossOfContinuityClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.92 | ||||
notification · current This notification reports (Ethernet OAM Continuity Check) Loss Of Continuity clear. | |||||
| !opticsimAlarmEthOAMMisMergeConditionRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.93 | ||||
notification · current This notification reports (Ethernet OAM Continuity Check) MisMerge Condition raise. | |||||
| !opticsimAlarmEthOAMMisMergeConditionClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.94 | ||||
notification · current This notification reports (Ethernet OAM Continuity Check) MisMerge Condition clear. | |||||
| !opticsimAlarmEthOAMUnexpectedMepIdRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.95 | ||||
notification · current This notification reports (Ethernet OAM Continuity Check) UnexpectedMepId raise. | |||||
| !opticsimAlarmEthOAMUnexpectedMepIdClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.96 | ||||
notification · current This notification reports (Ethernet OAM Continuity Check) UnexpectedMepId Clear. | |||||
| !opticsimAlarmEthOAMUnexpectedPeriodRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.97 | ||||
notification · current This notification reports (Ethernet OAM Continuity Check) Unexpected Period raise. | |||||
| !opticsimAlarmEthOAMUnexpectedPeriodClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.98 | ||||
notification · current This notification reports (Ethernet OAM Continuity Check) Unexpected Period Clear. | |||||
| !opticsimAlarmEthOAMUnexpectedLevelRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.99 | ||||
notification · current This notification reports (Ethernet OAM Continuity Check) Unexpected Level raise. | |||||
| !opticsimAlarmEthOAMUnexpectedLevelClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.100 | ||||
notification · current This notification reports (Ethernet OAM Continuity Check) Unexpected Level clear. | |||||
| !opticsimAlarmEthOAMRDIRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.101 | ||||
notification · current This notification reports (Ethernet OAM Continuity Check) Remote Defect Indication raise. | |||||
| !opticsimAlarmEthOAMRDIClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.102 | ||||
notification · current This notification reports (Ethernet OAM Continuity Check) Remote Defect Indication clear. | |||||
| !opticsimAlarmSynchronizationSignalFailRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.103 | ||||
notification · current This notification reports the synchronization signal fail raise. | |||||
| !opticsimAlarmSynchronizationSignalFailClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.104 | ||||
notification · current This notification reports the synchronization signal fail clear. | |||||
| !opticsIMMemoryCardForbiddenToUseRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.105 | ||||
notification · current This notification reports the Memory card forbidden to use alarm raise. | |||||
| !opticsIMMemoryCardForbiddenToUseClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.106 | ||||
notification · current This notification reports the Memory card forbidden to use alarm clear. | |||||
| !opticsIMAlarmLinkOdncRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.107 | ||||
notification · current This notification reports the unsuccessful completion of Link OAM Discovery protocol. | |||||
| !opticsIMAlarmLinkOdncClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.108 | ||||
notification · current This notification reports the ODNC defect clear. | |||||
| !opticsIMAlarmLinkCleRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.109 | ||||
notification · current This notification reports that at least one Critical Link Event flag is present in the received OAMPDUs. | |||||
| !opticsIMAlarmLinkCleClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.110 | ||||
notification · current This notification reports the CL Event defect clear. | |||||
| !opticsIMAlarmLinkSiRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.111 | ||||
notification · current This notification reports an inconsistency of states between the two peer DTEs | |||||
| !opticsIMAlarmLinkSiClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.112 | ||||
notification · current This notification reports the SI defect clear. | |||||
| !opticsimAlarmEthOAMUNPrRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.113 | ||||
notification · current This notification reports 'A MEP receives a CCM frame with an invalid Priority, but a valid MEG and MEP values' raise. | |||||
| !opticsimAlarmEthOAMUNPrClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.114 | ||||
notification · current This notification reports 'A MEP receives a CCM frame with an invalid Priority, but a valid MEG and MEP values' clear. | |||||
| !opticsimAlarmClockFailureRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.115 | ||||
notification · current This notification reports the failure of the clock raise. | |||||
| !opticsimAlarmClockFailureClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.116 | ||||
notification · current This notification reports the the failure of the clock clear. | |||||
| !opticsimAlarmEthSignalDegradedRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.117 | ||||
notification · current This notification reports the signal degrade on the Ethernet link raise. | |||||
| !opticsimAlarmEthSignalDegradeClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.118 | ||||
notification · current This notification reports the signal degrade on the Ethernet link clear. | |||||
| !opticsimAlarmEthPNACRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.119 | ||||
notification · current This notification reports that the 'ethernet port-based authentication is failed' is raised. | |||||
| !opticsimAlarmEthPNACClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.120 | ||||
notification · current This notification reports that 'ethernet port-based authentication is failed' is cleared. | |||||
| !opticsimAlarmAutomaticEthShutdownRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.121 | ||||
notification · current This notification reports the 'Ethernet port shutdown' due not to local problems (on Ethernet port) but due to some problems on the associated interface on NE' defect raise. | |||||
| !opticsimAlarmAutomaticEthShutdownClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.122 | ||||
notification · current This notification reports the 'Ethernet port shutdown' due not to local problems (on Ethernet port) but due to some problems on the associated interface on NE' defect clear. | |||||
| !opticsimAlarmEthFOPCMRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.123 | ||||
notification · current This notification for 'Reception of an APS frame from the working transport entity for ethernet 1:1 EVC protection group' is raise. | |||||
| !opticsimAlarmEthFOPCMClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.124 | ||||
notification · current This notification for 'Reception of an APS frame from the working transport entity for ethernet 1:1 EVC protection group' is clear | |||||
| !opticsimAlarmEthFOPPMRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.125 | ||||
notification · current This notification for 'Reception of an APS frame with incompatible -B- bit value' is raise. | |||||
| !opticsimAlarmEthFOPPMClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.126 | ||||
notification · current This notification for 'Reception of an APS frame with incompatible -B- bit value' is clear | |||||
| !opticsimAlarmEthFOPNRRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.127 | ||||
notification · current This notification for 'Reception of an APS frame with incompatible -Requested Signal- value' is raise. | |||||
| !opticsimAlarmEthFOPNRClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.128 | ||||
notification · current This notification for 'Reception of an APS frame with incompatible -Requested Signal- value' is clear | |||||
| !opticsimAlarmEthFOPAMRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.129 | ||||
notification · current This notification for 'Reception of an APS frame with incompatible -A- bit value' is raise. | |||||
| !opticsimAlarmEthFOPAMClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.130 | ||||
notification · current This notification for 'Reception of an APS frame with incompatible -A- bit value' is clear | |||||
| !opticsimAlarmEthFOPDMRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.131 | ||||
notification · current This notification for 'Reception of an APS frame with incompatible -D- bit value' is raise. | |||||
| !opticsimAlarmEthFOPDMClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.132 | ||||
notification · current This notification for 'Reception of an APS frame with incompatible -D- bit value' is clear | |||||
| !opticsimAlarmEthNOSYNCRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.133 | ||||
notification · current This notification for 'Loss Of synchronisation for ethernet port' is raise | |||||
| !opticsimAlarmEthNOSYNClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.134 | ||||
notification · current This notification for 'Loss Of synchronisation for ethernet port' is clear | |||||
| !opticsimAlarmEthANMRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.135 | ||||
notification · current This notification for 'Auto-Negotiation_Mismatch' is raise. | |||||
| !opticsimAlarmEthANMClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.136 | ||||
notification · current This notification for 'Auto-Negotiation_Mismatcht' is clear | |||||
| !opticsimAlarmHldOverRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.137 | ||||
notification · current This notification for 'The system clock is in the holdover or free-running mode' is raise. | |||||
| !opticsimAlarmHldOverClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.138 | ||||
notification · current This notification for 'The system clock is in the holdover or free-running mode' is clear | |||||
| !opticsimTLURaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.139 | ||||
notification · current This notification for 'Timing Link Unequiped' is raise. | |||||
| !opticsimTLUClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.140 | ||||
notification · current This notification for 'Timing Link Unequiped' is clear | |||||
| !opticsimAlarmPDHTLCRRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.141 | ||||
notification · current This notification for 'Total loss capacity in receive direction' is raise | |||||
| !opticsimAlarmPDHTLCRClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.142 | ||||
notification · current This notification for 'Total loss capacity in receive direction' is clear | |||||
| !opticsimAlarmPDHTLCTRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.143 | ||||
notification · current This notification for 'Total loss capacity in transmission direction' is raise. | |||||
| !opticsimAlarmPDHTLCTClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.144 | ||||
notification · current This notification for 'Total loss capacity in transmission direction' is clear | |||||
| !opticsimAlarmPDHPLCTRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.145 | ||||
notification · current This notification for 'Patial loss capacity in transmission direction' is raise. | |||||
| !opticsimAlarmPDHPLCTClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.146 | ||||
notification · current This notification for 'Patial loss capacity in transmission direction' is clear | |||||
| !opticsimAlarmPDHPLCRRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.147 | ||||
notification · current This notification for 'Patial loss capacity in receive direction' is raise | |||||
| !opticsimAlarmPDHPLCRClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.148 | ||||
notification · current This notification for 'Patial loss capacity in receive direction' is clear | |||||
| !opticsimAlarmPDHMNDRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.149 | ||||
notification · current This notification for 'Member not deskewable fault cause' is raise | |||||
| !opticsimAlarmPDHMNDClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.150 | ||||
notification · current This notification for 'Member not deskewable fault cause' is clear | |||||
| !opticsIMRetimingBufferOverflowRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.151 | ||||
notification · current This notification reports the 'Ethernet port shutdown' due not to local problems (on Ethernet port) but due to some problems on the associated interface on NE' defect raise. | |||||
| !opticsIMRetimingBufferOverflowClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.152 | ||||
notification · current This notification reports the 'Ethernet port shutdown' due not to local problems (on Ethernet port) but due to some problems on the associated interface on NE' defect clear. | |||||
| !opticsimAlarmFailureOfProtocolProvisioningMismatchRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.153 | ||||
notification · current This notification reports the Failure of protocol Provisioning Mismatch event raise | |||||
| !opticsimAlarmFailureOfProtocolProvisioningMismatchClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.154 | ||||
notification · current This notification reports the Failure of protocol Provisioning Mismatch event clear | |||||
| !opticsimAlarmFailureOfProtocolTimeOutRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.155 | ||||
notification · current This notification reports the Failure of protocol TimeOut event raise | |||||
| !opticsimAlarmFailureOfProtocolTimeOutClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.156 | ||||
notification · current This notification reports the Failure of protocol TimeOut event clear | |||||
| !opticsimAlarmLoopingFrameEventRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.157 | ||||
notification · current This notification reports the looping frame event raise | |||||
| !opticsimAlarmLoopingFrameEventClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.158 | ||||
notification · current This notification reports the looping frame event clear | |||||
| !opticsimAlarmEthOAMMIPOverflowEventRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.159 | ||||
notification · current This notification reports the MIP OverFlow event raise | |||||
| !opticsimAlarmEthOAMMIPOverflowEventClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.160 | ||||
notification · current This notification reports the MIP OverFlow event clear | |||||
| !opticsimAlarmMcastTableOverflowEventRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.161 | ||||
notification · current This notification reports the Multicast table OverFlow event raise | |||||
| !opticsimAlarmMcastTableOverflowEventClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.162 | ||||
notification · current This notification reports the Multicast table OverFlow event clear | |||||
| !opticsimAlarmEthOAMVSFRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.163 | ||||
notification · current This notification reports the VSF defect raise. | |||||
| !opticsimAlarmEthOAMVSFClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.164 | ||||
notification · current This notification reports the VSF defect clear. | |||||
| !opticsIMAlarmExSERRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.165 | ||||
notification · current This notification reports an excessive rate of symbol errors on the line. In case of 10GE interfaces it reports an excessive rate of invalid blocks. The threshold rate is configurable as maximum number of symbol errors/ invalid blocks in one second using the opticsIMlinkEnhSymbErrThr object in opticsIMlinkEnhTable. | |||||
| !opticsIMAlarmExSERClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.166 | ||||
notification · current This notification reports an excessive symbol error rate alarm clear. | |||||
| !opticsIMAlarmLossOfCESoETHFrameRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.167 | ||||
notification · current This notification reports the loss of CES Frame (LCF) defect raise | |||||
| !opticsIMAlarmLossOfCESoETHFrameClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.168 | ||||
notification · current This notification reports the loss of CES Frame (LCF) defect clear | |||||
| !opticsimAlarmLossOfProtectionRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.169 | ||||
notification · current This notification reports the loss of protection defect raise. | |||||
| !opticsimAlarmLossOfProtectionClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.170 | ||||
notification · current This notification reports the loss of protection defect clear. | |||||
| !opticsIMAlarmAisTxRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.171 | ||||
notification · current This notification reports the AIS in Tx direction defect raise. | |||||
| !opticsIMAlarmAisTxClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.172 | ||||
notification · current This notification reports the AIS in Tx direction defect clear. | |||||
| !opticsIMAlarmAisRxRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.173 | ||||
notification · current This notification reports the AIS in Rx direction defect raise. | |||||
| !opticsIMAlarmAisRxClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.174 | ||||
notification · current This notification reports the AIS in Rx direction defect clear. | |||||
| !opticsIMAlarmUrdRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.175 | ||||
notification · current This notification reports the Underline Resource Degraded (URD) defect raise. | |||||
| !opticsIMAlarmUrdClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.176 | ||||
notification · current This notification reports the Underline Resource Degraded (URD) defect clear. | |||||
| !opticsIMAlarmUrusRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.177 | ||||
notification · current This notification reports the Underline Resource Unavailable Service (URUS) defect raise. | |||||
| !opticsIMAlarmUrusClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.178 | ||||
notification · current This notification reports the Underline Resource Unavailable Service (URUS) defect clear. | |||||
| !opticsIMAlarmLossOfESMCRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.179 | ||||
notification · current This notification reports the Loss of Ethernet Synchronisation Messaging Channel defect raise. | |||||
| !opticsIMAlarmLossOfESMCClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.180 | ||||
notification · current This notification reports the Loss of Ethernet Synchronisation Messaging Channel defect clear. | |||||
| !opticsIMAlarmStraypacketsRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.181 | ||||
notification · current This notification reports the Stray Packets defect raise. | |||||
| !opticsIMAlarmStraypacketsClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.182 | ||||
notification · current This notification reports the Stray Packets defect clear. | |||||
| !opticsIMAlarmExcessivepacketLossRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.183 | ||||
notification · current This notification reports the Excessive Packet Loss defect raise. | |||||
| !opticsIMAlarmExcessivepacketLossClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.184 | ||||
notification · current This notification reports the Excessive Packet Loss Rate defect clear. | |||||
| !opticsIMAlarmRemotepacketlossRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.185 | ||||
notification · current This notification reports the Remote Packet Loss defect raise. | |||||
| !opticsIMAlarmRemotepacketlossClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.186 | ||||
notification · current This notification reports the Remote Packet Loss defect clear. | |||||
| !opticsIMAlarm1PpsTodLOSRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.187 | ||||
notification · current The alarm is raised if 1PPS pulse can't be detected within 3s time if the 1PPS/TOD interface is enabled.. | |||||
| !opticsIMAlarm1PpsTodLOSClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.188 | ||||
notification · current The alarm is cleared if 1PPS signal can be detected within 1s time for consecutive 3s timeline. | |||||
| !opticsIMAlarm1PpsToDDEGRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.189 | ||||
notification · current The alarm is raised if 1PPS pulse can be received within 1s
time (not 1PPS/TOD LOS) but the operational status of 1PPS is degraded and
the 1PPS/TOD interface is enabled. | |||||
| !opticsIMAlarm1PpsToDDEGClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.190 | ||||
notification · current The alarm is cleared if 1PPS pulse can be received within 1s time (not 1PPS/TOD LOS) and the operational status of 1PPS/ToD is normal. | |||||
| !opticsIMAlarmPtpLossOfLockRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.191 | ||||
notification · current The alarm is raised if PTP recovered Clock state is NOT in LOCKED state and the PTP port is enabled. | |||||
| !opticsIMAlarmPtpLossOfLockClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.192 | ||||
notification · current The alarm is cleared if PTP recovered Clock state is in LOCKED state. | |||||
| !opticsIMAlarmPtpFaultyRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.193 | ||||
notification · current The alarm is raised if PTP port is in Faulty and the PTP port is enabled. | |||||
| !opticsIMAlarmPtpFaultyClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.194 | ||||
notification · current The alarm is cleared if PTP recovered Clock state is NOT in Faulty state. | |||||
| !opticsIMAlarmInvalidTdmDataRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.195 | ||||
notification · current This notification reports that the 'L' bit is set in SAToP Control Word, it indicate that TDM data carried in the payload is invalid due to an attachment circuit fault. | |||||
| !opticsIMAlarmInvalidTdmDataClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.196 | ||||
notification · current This notification reports that the 'L' bit is cleared in SAToP Control Word:. | |||||
| !opticsIMAlarmIncompatibleProtectionRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.197 | ||||
notification · current This notification reports the raise of the incompatibility between equipment for protection scope. | |||||
| !opticsIMAlarmIncompatibleProtectionClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.198 | ||||
notification · current This notification reports the clear of the incompatibility between equipment for protection scope. | |||||
| !opticsIMAlarmBandwidthDegradeForProtectionSwitchRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.199 | ||||
notification · current This notification reports the raise of the bandwidth degrade in case of protection switch. | |||||
| !opticsIMAlarmBandwidthDegradeForProtectionSwitchClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.200 | ||||
notification · current This notification reports the clear of the bandwidth degrade in case of protection switch. | |||||
| !opticsIMAlarmDuplicatedAddressDetectedRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.201 | ||||
notification · current This notification reports the raise of the detection of an IP address duplication. | |||||
| !opticsIMAlarmDuplicatedAddressDetectedClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.202 | ||||
notification · current This notification reports the clear of the detection of an IP address duplication. | |||||
| !opticsIMAlarmLoopbackPresenceRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.203 | ||||
notification · current This notification reports the raise of the loopback alarm presence. | |||||
| !opticsIMAlarmLoopbackPresenceClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.204 | ||||
notification · current This notification reports the clear of the loopback alarm presence. | |||||
| !opticsIMAlarmServiceSelectiveDropRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.205 | ||||
notification · current This notification reports the raise of the service selective drop . | |||||
| !opticsIMAlarmServiceSelectiveDropClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.206 | ||||
notification · current This notification reports the clear of the service selective drop. | |||||
| !opticsimAlarmlnkaggExBandwidthDegradeRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.207 | ||||
notification · current This notification reports the raise of the LAG Excessive Bandwidth Degrade alarm presence. | |||||
| !opticsimAlarmlnkaggExBandwidthDegradeClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.208 | ||||
notification · current This notification reports the clear of the LAG Excessive Bandwidth Degrade alarm presence. | |||||
| !opticsIMAlarmRemoteFaultIndicationRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.209 | ||||
notification · current This notification reports the Remote Fault Indication (RFI) defect raise. | |||||
| !opticsIMAlarmRemoteFaultIndicationClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.210 | ||||
notification · current This notification reports the Remote Fault Indication (RFI) defect clear. | |||||
| !opticsIMAlarm1588AnnouncePktLOSRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.211 | ||||
notification · current The alarm is raised if the 1588 Announce packet loss is detected, the default detect interval is 3 packets. | |||||
| !opticsIMAlarm1588AnnouncePktLOSClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.212 | ||||
notification · current The alarm is cleared if the 1588 Announce packet loss is not detected. | |||||
| !opticsIMAlarm1588SyncPktLOSRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.213 | ||||
notification · current The alarm is raised if the 1588 sync packet loss is detected, the default detect interval is 3 packets. | |||||
| !opticsIMAlarm1588SyncPktLOSClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.214 | ||||
notification · current The alarm is cleared if the 1588 sync packet loss is not detected. | |||||
| !opticsIMAlarm1588DelayRespPktLOSRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.215 | ||||
notification · current The alarm is raised if the 1588 Delay_resp packet is not received, the default detect interval is 3 packets. | |||||
| !opticsIMAlarm1588DelayRespPktLOSClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.216 | ||||
notification · current The alarm is cleared if the 1588 Delay_resp packet is received. | |||||
| !opticsIMAlarm1588PTPClockclassDEGRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.217 | ||||
notification · current The alarm is raised if PTP clockclass is smaller than the value of the specific threshold,and the value of 'stepsRemoved' for PTP reference source is '0', the default threshold value is 6. | |||||
| !opticsIMAlarm1588PTPClockclassDEGClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.218 | ||||
notification · current The alarm is cleared if PTP clockclass is bigger than the value of the specific threshold,or the value of 'stepsRemoved' for PTP reference source is not '0', the default threshold value is 6. | |||||
| !opticsIMAlarmESMCPktLosRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.219 | ||||
notification · current The alarm shall be raised if the ESMC packet is lost. | |||||
| !opticsIMAlarmESMCPktLosClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.220 | ||||
notification · current The alarm shall be cleared if the ESMC packet is received. | |||||
| !opticsimAlarmLossOfPktSynchronizationRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.221 | ||||
notification · current This notification reports the raise of the Loss Of CEP Packet Synchronization alarm presence. | |||||
| !opticsimAlarmLossOfPktSynchronizationClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.222 | ||||
notification · current This notification reports the clear of the Loss Of CEP Packet Synchronization alarm presence. | |||||
| !opticsimAlarmExcessiveMissingPktRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.223 | ||||
notification · current This notification reports the raise of the Excessive Missing CEP Packet alarm presence. | |||||
| !opticsimAlarmExcessiveMissingPktClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.224 | ||||
notification · current This notification reports the clear of the Excessive Missing CEP Packet alarm presence. | |||||
| !opticsimAlarm1588TCFailRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.225 | ||||
notification · current This notification reports the raise of the 1588 Transparent Clock Fail alarm presence. | |||||
| !opticsimAlarm1588TCFailClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.226 | ||||
notification · current This notification reports the clear of the 1588 Transparent Clock Fail alarm presence. | |||||
| !opticsimAlarmTrafficDownRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.227 | ||||
notification · current This notification reports the raise of the Traffic Down alarm presence. | |||||
| !opticsimAlarmTrafficDownClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.228 | ||||
notification · current This notification reports the clear of the Traffic Down alarm presence. | |||||
| !opticsimAlarmTrafficLossRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.229 | ||||
notification · current This notification reports the raise of the Traffic Loss alarm presence. | |||||
| !opticsimAlarmTrafficLossClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.230 | ||||
notification · current This notification reports the clear of the Traffic Loss alarm presence. | |||||
| !opticsimAlarmRxProblemRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.231 | ||||
notification · current This notification reports the raise of Rx Problem alarm presence. | |||||
| !opticsimAlarmRxProblemClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.232 | ||||
notification · current This notification reports the clear of the Rx Problem alarm presence. | |||||
| !opticsimAlarmTxProblemRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.233 | ||||
notification · current This notification reports the raise of the Tx Problem alarm presence. | |||||
| !opticsimAlarmTxProblemClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.234 | ||||
notification · current This notification reports the clear of the Tx Problem alarm presence. | |||||
| !opticsimAlarmLagPortDownRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.235 | ||||
notification · current This notification reports the raise of LAG Port Down alarm presence. | |||||
| !opticsimAlarmLagPortDownClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.236 | ||||
notification · current This notification reports the clear of the LAG Port Down alarm presence. | |||||
| !opticsimAlarmCKMRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.237 | ||||
notification · current This notification reports the raise of the Current Key Mismatch alarm presence. | |||||
| !opticsimAlarmCKMClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.238 | ||||
notification · current This notification reports the clear of the Current Key Mismatch alarm presence. | |||||
| !opticsimAlarmNKMRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.239 | ||||
notification · current This notification reports the raise of the Next Key Mismatch alarm presence. | |||||
| !opticsimAlarmNKMClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.240 | ||||
notification · current This notification reports the clear of the Next Key Mismatch alarm presence. | |||||
| !opticsimAlarmAesFipsFailureRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.241 | ||||
notification · current This notification reports the raise of the AES engine Failure alarm presence. | |||||
| !opticsimAlarmAesFipsFailureClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.242 | ||||
notification · current This notification reports the clear of the AES engine Failure alarm presence. | |||||
| !opticsimAlarmSessionTimeoutRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.243 | ||||
notification · current This notification reports the raise of the expiration (timeout) of the current manager session alarm presence. | |||||
| !opticsimAlarmSessionTimeoutClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.244 | ||||
notification · current This notification reports the clear of the expiration (timeout) of the current manager session alarm presence. | |||||
| !opticsimThresholdOutputPowerHighRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.245 | ||||
notification · current This notification reports the raise of warning condition of exceeding Threshold of transmitting Power too High. | |||||
| !opticsimThresholdOutputPowerHighClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.246 | ||||
notification · current This notification reports the clear of warning condition of exceeding Threshold of transmitting Power too High. | |||||
| !opticsimThresholdOutputPowerLowRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.247 | ||||
notification · current This notification reports the raise of warning condition of exceeding Threshold of transmitting Power too Low. | |||||
| !opticsimThresholdOutputPowerLowClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.248 | ||||
notification · current This notification reports the clear of warning condition of exceeding Threshold of transmitting Power too Low. | |||||
| !opticsimThresholdInputPowerHighRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.249 | ||||
notification · current This notification reports the raise of warning condition of exceeding Threshold of receiving Power too High. | |||||
| !opticsimThresholdInputPowerHighClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.250 | ||||
notification · current This notification reports the clear of warning condition of exceeding Threshold of receiving Power too High. | |||||
| !opticsimThresholdInputPowerLowRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.251 | ||||
notification · current This notification reports the raise of warning condition of exceeding Threshold of receiving Power too Low. | |||||
| !opticsimThresholdInputPowerLowClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.252 | ||||
notification · current This notification reports the clear of warning condition of exceeding Threshold of receiving Power too Low. | |||||
| !opticsimInputPowerOverloadRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.253 | ||||
notification · current This notification reports the raise of alarm condition of exceeding Threshold of receiving Power too High. | |||||
| !opticsimInputPowerOverloadClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.254 | ||||
notification · current This notification reports the clear of alarm condition of exceeding Threshold of receiving Power too High. | |||||
| !opticsimAlarmESMRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.255 | ||||
notification · current This notification reports the raise of the Encryption State Mismatch alarm presence. | |||||
| !opticsimAlarmESMClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.256 | ||||
notification · current This notification reports the clear the Encryption State Mismatch alarm presence. | |||||
| !opticsimAlarmKeyUnavailableRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.257 | ||||
notification · current This notification reports the raise of the encryption key not available (or missing) alarm presence. | |||||
| !opticsimAlarmKeyUnavailableClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.258 | ||||
notification · current This notification reports the clear of the encryption key not available (or missing) alarm presence. | |||||
| !opticsimFreeLicenseRunningRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.259 | ||||
notification · current This notification reports the raise of the alarm to advice that the node is working in normal mode but without license key (free license). | |||||
| !opticsimFreeLicenseRunningClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.260 | ||||
notification · current This notification reports the clear of the alarm to advice that the node is working in normal mode but without license key (free license). | |||||
| !opticsimFreeLicenseExpiredRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.261 | ||||
notification · current This notification reports the raise of the alarm to advice that the node is working in degraded mode for license missing. | |||||
| !opticsimFreeLicenseExpiredClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.262 | ||||
notification · current This notification reports the clear of the alarm to advice that the node is working in degraded mode for license missing. | |||||
| !opticsIMAlarmStolenStatusRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.263 | ||||
notification · current This notification reports the raise of the alarm for the node entered on Stolen Status. | |||||
| !opticsIMAlarmStolenStatusClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.264 | ||||
notification · current This notification reports the clear of the alarm for the node entered on Stolen Status. | |||||
| !opticsIMAlarmEthOAMUnexpectedMepRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.265 | ||||
notification · current This notification reports (Ethernet OAM Continuity Check) mismatch problems on CCM on receiving MEP. | |||||
| !opticsIMAlarmEthOAMUnexpectedMepClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.266 | ||||
notification · current This notification reports the clear of the (Ethernet OAM Continuity Check) mismatch problems on CCM on receiving MEP. | |||||
| !opticsIMAlarmEthOAMMACStatusDefectRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.267 | ||||
notification · current This notification reports the raise of the (Ethernet OAM Continuity Check) MAC Status defect. | |||||
| !opticsIMAlarmEthOAMMACStatusDefectClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.268 | ||||
notification · current This notification reports the clear of the (Ethernet OAM Continuity Check) MAC Status defect. | |||||
| !opticsIMAlarmLogUploadFailureRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.269 | ||||
notification · current This notification reports the raise of the Log Upload Failure defect. | |||||
| !opticsIMAlarmLogUploadFailureClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.270 | ||||
notification · current This notification reports the clear of the Log Upload Failure defect. | |||||
| !opticsIMAlarmIpsecPskMissingRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.271 | ||||
notification · current This notification reports the raise of the IPSec PSK (Pre Secret Key) missing defect. | |||||
| !opticsIMAlarmIpsecPskMissingClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.272 | ||||
notification · current This notification reports the clear of the IPSec PSK (Pre Secret Key) missing defect. | |||||
| !opticsIMAlarmIpsecTunnelSetupFailureRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.273 | ||||
notification · current This notification reports the raise of the IPSec tunnel set-up failure defect. | |||||
| !opticsIMAlarmIpsecTunnelSetupFailureClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.274 | ||||
notification · current This notification reports the clear of the IPSec tunnel set-up failure defect. | |||||
| !opticsIMAlarmSecureSelfTestFailureRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.275 | ||||
notification · current This notification reports the raise of the secure self-test failure defect. | |||||
| !opticsIMAlarmSecureSelfTestFailureClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.276 | ||||
notification · current This notification reports the clear of the secure self-test failure defect. | |||||
| !opticsIMAlarmEthOAMUnexpectedCcmConnectivityRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.277 | ||||
notification · current This notification reports the raise of the ETH OAM Unexpected CCM conectivity defect. | |||||
| !opticsIMAlarmEthOAMUnexpectedCcmConnectivityClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.278 | ||||
notification · current This notification reports the clear of the ETH OAM Unexpected CCM conectivity defect. | |||||
| !opticsIMAlarmSecureModeMismatchRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.279 | ||||
notification · current This notification reports the raise of the Secure mode mismatch defect. | |||||
| !opticsIMAlarmSecureModeMismatchClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.280 | ||||
notification · current This notification reports the clear of the Secure mode mismatch defect. | |||||
| !opticsIMAlarmSWDLConditionalSelfTestFailRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.281 | ||||
notification · current This notification reports the raise of the Sw Download Conditional Self test defect. | |||||
| !opticsIMAlarmSWDLConditionalSelfTestFailClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.282 | ||||
notification · current This notification reports the clear of the Sw Download Conditional Self test defect. | |||||
| !opticsIMAlarmCRNGConditionalSelfTestFailRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.283 | ||||
notification · current This notification reports the raise of the Conditional Random Number Generator (CRNG) Self test defect. | |||||
| !opticsIMAlarmCRNGConditionalSelfTestFailClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.284 | ||||
notification · current This notification reports the clear of the Conditional Random Number Generator (CRNG) Self test defect. | |||||
| !opticsIMAlarmUpdateIPSecKeysFailRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.285 | ||||
notification · current This notification reports the raise of the Update of IP Sec Key Fail alarm. | |||||
| !opticsIMAlarmUpdateIPSecKeysFailClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.286 | ||||
notification · current This notification reports the clear of the Update of IP Sec Key Fail alarm. | |||||
| !opticsIMAlarmZeroizeIPSecKeysFailRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.287 | ||||
notification · current This notification reports the raise of the Zeroize of the IP Sec Key Fail alarm. | |||||
| !opticsIMAlarmZeroizeIPSecKeysFailClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.288 | ||||
notification · current This notification reports the clear of the Zeroize of the IP Sec Key Fail alarm. | |||||
| !opticsIMAlarmVESListenerConnectionFailureRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.289 | ||||
notification · current This notification reports the raise of the alarm for problems to send VES events to Listener Collector . | |||||
| !opticsIMAlarmVESListenerConnectionFailureClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.290 | ||||
notification · current This notification reports the clear of the alsrm for problems to send VES events to Listener Collector . | |||||
| !opticsIMAlarmMissingDiversityAlignConfRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.291 | ||||
notification · current This notification reports the raise of the alarm for problems to send VES events to Listener Collector . | |||||
| !opticsIMAlarmMissingDiversityAlignConfClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.292 | ||||
notification · current This notification reports the clear of the alsrm for problems to send VES events to Listener Collector . | |||||
| !opticsIMAlarmACMDegradeRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.293 | ||||
notification · current This notification reports the raise of the alarm for ACM Degrade, when the max Modulation is not reached for a specific time period . | |||||
| !opticsIMAlarmACMDegradeClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.294 | ||||
notification · current This notification reports the clear of the alarm for ACM Degrade. | |||||
| !opticsIMAlarmLocalAutoTxMuteRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.295 | ||||
notification · current This notification reports the raise of the alarm for auto mute. | |||||
| !opticsIMAlarmLocalAutoTxMuteClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.296 | ||||
notification · current This notification reports the clear of the alarm for auto mute. | |||||
| !opticsIMAlarmLossOfContinuityRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.297 | ||||
notification · current This notification reports the raise of the Loss Of Continuity alarm on the resource specified. | |||||
| !opticsIMAlarmLossOfContinuityClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.298 | ||||
notification · current This notification reports the clear of the Loss Of Continuity alarm on the resource specified. | |||||
| !opticsIMAlarmPowerSavingActiveRaise | 1.3.6.1.4.1.637.54.1.1.5.1.40.299 | ||||
notification · current This notification reports the activation of the Power Saving on the resource specified. | |||||
| !opticsIMAlarmPowerSavingActiveClear | 1.3.6.1.4.1.637.54.1.1.5.1.40.300 | ||||
notification · current This notification reports the deactivation of the Power Saving on the resource specified. | |||||
| SopticsIMdatabaseModify | 1.3.6.1.4.1.637.54.1.1.5.1.41 | TsdimEventTimeInt | RO | ||
scalar · TsdimEventTimeInt · read-only · current This attribute stores the information that a local operator has changed the configuration in a persistent way. It contains the date of the last time the LAC status has become granted. | |||||
| SopticsimSwPackageProfileRequested | 1.3.6.1.4.1.637.54.1.1.5.1.42 | Bits | RW | ||
scalar · Bits · read-write · current This object is used for configuring the software package profile which indicates the network functionalities enabled on the NE. If the requested profile is compatible with the downloaded software, the configuration is accepted, the value is saved in the boot NE area and, when the NE has been restarted, the value will be effective and it will be mirrored in the opticsimSwPackageProfile, otherwise the error code badValue has to be returned. The value of this attribute is commonly agreed, its semantic will be described in the relevant Ext. Interface Management Specification.
| |||||
| TopticsIMPoolTable | 1.3.6.1.4.1.637.54.1.1.5.1.43 | NA | |||
table · not-accessible · current This table defines the pools available in the node. The following pools are defined:
poolID pool poolDescription
--------------------------------------------------------------------
1 Pool1 Packet Processor Bandwidth (kbit)
2 Pool2 Packet Processor CAM (Number of entries)
3 Pool3 Traffic Manager Logical Ports (number of ports)
4 Pool4 Traffic Descriptors (number of TD)
5 Pool5 InFlows (number of flows)
6 Pool6 OutFlows (number of flows)
7 Pool7 CrossConnections (number of XC)
8 Pool8 Link Aggregation Groups (number of LAG)
9 Pool9 Spanning Tree Instances (number of instances)
10 Pool10 Matrix channels (number of channels)
11 Pool11 Bandwidth for Remote Ports
12 Pool12 Ethernet classifiers (number of ETS Classifiers)
13 Pool13 Static VLAN registration entries (number of
registered VLANs)
14 Pool14 (IVL/SVL)Dynamic Filtering Entries (number of
dynamic entries)
15 Pool15 (IVL/SVL)Static Filtering Entries (number of static
entries)
16 Pool16 IGMP Snooping Entries (number of IGMP Snooping
Entries)
17 Pool17 MPLS InSegments (number of MPLS InSegments)
18 Pool18 MPLS OutSegments (number of MPLS OutSegments)
19 Pool19 MPLS Tunnels (number of MPLS Tunnels)
20 Pool20 MPLS Traffic Descriptors (number of MPLS Traffic
Descriptors) | |||||
| RopticsIMPoolEntry | 1.3.6.1.4.1.637.54.1.1.5.1.43.1 | NA | |||
row · not-accessible · current Each entry is a resource pool associated to a defined position (open to be
extended).
Description of entries:
- positionID: it is the physical position of the board (e.g. slot). It is
used as entry for the resources associated for example to the board
configured in a slot. It is used positionID 0.0.0.0.0 (zero) to indicate
pools for the whole Network element.
- poolID: it is a unique identifier describing the pool; the association
poolID - pool descriptor is provided in the behaviour.
- nominalResources: the maximum number of resources available (by
definition)
- UsedResources: the number of used resources
- availableResources: the current available resources (it's the nominal
subtracted the used).
- crossRelation: it is a field used when different items in the network
element (e.g. different boards) share the same pools of resources. The
typical case is when Access Card (providing physical access) are used.
In this case the same pool information is repeated for the slots
containing the main board and the access card itself and in
correspondence to the access card slot entries, the crossRelation field
indicates the slot related to the corresponding main board (and it is
indicated also in correspondence of the main board crossRelation). | |||||
| CopticsIMpositionID | 1.3.6.1.4.1.637.54.1.1.5.1.43.1.1 | OCTET STRING | NA | ||
column · OCTET STRING · not-accessible · current This object defines the physical position of the board referenced by the pool. | |||||
| CopticsIMpoolID | 1.3.6.1.4.1.637.54.1.1.5.1.43.1.2 | Integer32 | NA | ||
column · Integer32 · not-accessible · current This object defines the unique identifier describing the pool. | |||||
| CopticsIMPoolnominalResources | 1.3.6.1.4.1.637.54.1.1.5.1.43.1.3 | Integer32 | RO | ||
column · Integer32 · read-only · current This object indicates the maximum number of resources available. | |||||
| CopticsIMPoolusedResources | 1.3.6.1.4.1.637.54.1.1.5.1.43.1.4 | Integer32 | RO | ||
column · Integer32 · read-only · current This object indicates the number of used resources. | |||||
| CopticsIMPoolavailableResources | 1.3.6.1.4.1.637.54.1.1.5.1.43.1.5 | Integer32 | RO | ||
column · Integer32 · read-only · current This object indicates the current available resources. | |||||
| CopticsIMPoolcrossRelation | 1.3.6.1.4.1.637.54.1.1.5.1.43.1.6 | OCTET STRING | RO | ||
column · OCTET STRING · read-only · current This object is used when different items in the network element (e.g. different boards) share the same pools of resources. The typical case is when Access Card (providing physical access) are used. In this case the same pool information is repeated for the slots containing the main board and the access card itself and in correspondence to the access card slot entries, the crossRelation field indicates the slot related to the corresponding main board (and it is indicated also in correspondence of the main board crossRelation)the current available resources. | |||||
| SopticsimNeMtu | 1.3.6.1.4.1.637.54.1.1.5.1.44 | Unsigned32 | RW | ||
scalar · Unsigned32 · read-write · current This object reports 'on per NE basis' MTU (the size of the largest packet which can be sent/received on NE) specified in octets. For NE interfaces that are used for transmitting network datagrams, this is the size of the largest network datagram that can be sent on any NE interface. 'on per NE basis' MTU is mutually exclusive with 'on per port basis' MTU and is supported ONLY on NE without 'on per port basis' MTU provisioning. The value 0 (unknown) is the default value (with the meaning of no 'on per NE basis' MTU value). The support of 'on per NE basis' MTU is product specific and will be documented in the product external specification | |||||
| NopticsIMNeMACCollection | 1.3.6.1.4.1.637.54.1.1.5.1.45 | ||||
| SopticsIMNeMACCollectionStatus | 1.3.6.1.4.1.637.54.1.1.5.1.45.1 | INTEGER | RO | ||
scalar · INTEGER · read-only · current This object defines the MAC collection NE status: 2 operating status have been defined: the <Ready_for_Request> status, the <In_Preparation> status and the <File_Transfer_Completed> status; the default status is <Ready_for_Request>
| |||||
| SopticsIMNeMACActivateCollection | 1.3.6.1.4.1.637.54.1.1.5.1.45.2 | INTEGER | RW | ||
scalar · INTEGER · read-write · current This object defines the start of the MAC collection on NE: the value <NormalStart> is set by manager in order to activate the MAC collection in normal condition; the value <ForcedStart> is set by manager in order to activate the MAC collection in abnormal condition (for instance when NE is still preparing a previous commanded MAC collection); the agent will reset the value to <Noop> when the manager setting has been recognized. The default value is the <Noop> one.
| |||||
| TopticsIMIfQueueTable | 1.3.6.1.4.1.637.54.1.1.5.1.46 | NA | |||
table · not-accessible · current This table contains objects for each Forwarding queue of a NE interface. | |||||
| RopticsIMIfQueueEntry | 1.3.6.1.4.1.637.54.1.1.5.1.46.1 | NA | |||
row · not-accessible · current An entry references a forwarding Queue on each NE interface
| |||||
| CopticsIMIfQueueNumber | 1.3.6.1.4.1.637.54.1.1.5.1.46.1.1 | Integer32 | NA | ||
column · Integer32 · not-accessible · current The number of the forwarding queue within the forwarding queue set | |||||
| CopticsIMIfQueueType | 1.3.6.1.4.1.637.54.1.1.5.1.46.1.2 | INTEGER | RW | ||
column · INTEGER · read-write · current The type of the forwarding queue
| |||||
| CopticsIMIfQueueWeight | 1.3.6.1.4.1.637.54.1.1.5.1.46.1.3 | Integer32 | RW | ||
column · Integer32 · read-write · current The weight assigned to a weighted bandwidth forwarding queue; the returned value is meaningful ONLY for a weighted bandwidth forwarding queue | |||||
| CopticsIMIfQueueNominalBandwidth | 1.3.6.1.4.1.637.54.1.1.5.1.46.1.4 | Gauge32 | RO | ||
column · Gauge32 · read-only · current This attribute reports (in kbit/sec): - bandwidth parameter as inferred from assigned weight (in case of an egress weighted bandwidth Forwarding Queue); - Egress Link nominal bandwidth (in case of an egress strict priority Forwarding Queue) | |||||
| CopticsIMIfQueueAvailableBandwidth | 1.3.6.1.4.1.637.54.1.1.5.1.46.1.5 | Gauge32 | RO | ||
column · Gauge32 · read-only · current This attribute reports (in kbit/sec): - Available bandwidth parameter (in case of an egress weighted bandwidth Forwarding Queue); - Egress Link Available bandwidth (in case of an egress strict priority Forwarding Queue) | |||||
| CopticsIMIfQueueSlopeHiAdminStatus | 1.3.6.1.4.1.637.54.1.1.5.1.46.1.6 | INTEGER | RW | ||
column · INTEGER · read-write · current opticsIMIfQueueSlopeHiAdminStatus specifies the admin state for the Green packets (high priority) WRED slope. If the opticsIMIfQueueSlopeHiAdminStatus is set to 'down', the WRED slope is inactive. Default value is down
| |||||
| CopticsIMIfQueueSlopeHiStartAverage | 1.3.6.1.4.1.637.54.1.1.5.1.46.1.7 | Integer32 | RW | ||
column · Integer32 · read-write · current The percentage (0..100) of the buffer utilized after which the drop probability of Green packets starts to rise above 0. Default value is 70 | |||||
| CopticsIMIfQueueSlopeHiMaxAverage | 1.3.6.1.4.1.637.54.1.1.5.1.46.1.8 | Integer32 | RW | ||
column · Integer32 · read-write · current The percentage (0..100) of the buffer utilized after which the drop probability of Green packets is 100 percent. This implies that all Green packets beyond this point will be dropped.Default value is 90 | |||||
| CopticsIMIfQueueSlopeHiMaxProbability | 1.3.6.1.4.1.637.54.1.1.5.1.46.1.9 | Integer32 | RW | ||
column · Integer32 · read-write · current The drop probability (0..100) of Green packets increases steadily from 0 (at opticsIMIfQueueSlopeHiStartAverage) up to opticsIMIfQueueSlopeHiMaxProbability (at the opticsIMIfQueueSlopeHiMaxAverage). Default value is 80 | |||||
| CopticsIMIfQueueSlopeLoAdminStatus | 1.3.6.1.4.1.637.54.1.1.5.1.46.1.10 | INTEGER | RW | ||
column · INTEGER · read-write · current opticsIMIfQueueSlopeLoAdminStatus specifies the admin state for the Yellow packet (Low priority) WRED slope. If opticsIMIfQueueSlopeLoAdminStatus is set to 'down', the WRED slope is inactive.Default value is down
| |||||
| CopticsIMIfQueueSlopeLoStartAverage | 1.3.6.1.4.1.637.54.1.1.5.1.46.1.11 | Integer32 | RW | ||
column · Integer32 · read-write · current The percentage (0..100) of the buffer utilized after which the drop probability of Yellow packet starts to rise above 0. Default value is 50 | |||||
| CopticsIMIfQueueSlopeLoMaxAverage | 1.3.6.1.4.1.637.54.1.1.5.1.46.1.12 | Integer32 | RW | ||
column · Integer32 · read-write · current The percentage of the buffer utilized after which the drop probability of Yellow packets is 100 percent. This implies that all packets beyond this point will be dropped. Default is 75 | |||||
| CopticsIMIfQueueSlopeLoMaxProbability | 1.3.6.1.4.1.637.54.1.1.5.1.46.1.13 | Integer32 | RW | ||
column · Integer32 · read-write · current The drop probability (0..100) of Yellow packets increases steadily from 0 (at opticsIMIfQueueSlopeLoStartAverage) up to opticsIMIfQueueSlopeLoMaxProbability (at the opticsIMIfQueueSlopeLoMaxAverage).Default is 80 | |||||
| CopticsIMIfQueueSize | 1.3.6.1.4.1.637.54.1.1.5.1.46.1.14 | Integer32 | RW | ||
column · Integer32 · read-write · current This object is the buffer size of the queue in bytes as defined by managing system. | |||||
| CopticsIMIfQueueDefaultSize | 1.3.6.1.4.1.637.54.1.1.5.1.46.1.15 | Integer32 | RO | ||
column · Integer32 · read-only · current This object reports to the managing system the default value for the buffer size of the queue as applied by the agent. | |||||
| TopticsIMIfEgressFCMappingTable | 1.3.6.1.4.1.637.54.1.1.5.1.47 | NA | |||
| RopticsIMIfEgressFCMappingEntry | 1.3.6.1.4.1.637.54.1.1.5.1.47.1 | NA | |||
row · not-accessible · current This entry contains information about mappings of a particular forwarding class (including BOTH Green and Yellow packets) to a forwarding queue | |||||
| CopticsIMIfEgressFCNumber | 1.3.6.1.4.1.637.54.1.1.5.1.47.1.1 | Integer32 | NA | ||
column · Integer32 · not-accessible · current The number of the Forwarding Class: Forwarding Classes are numbered starting from 0 to 7 with increasing forwarding priority (Forwarding Class 0 with lowest forwarding priority) | |||||
| CopticsIMIfEgressFCQueue | 1.3.6.1.4.1.637.54.1.1.5.1.47.1.2 | Integer32 | RW | ||
column · Integer32 · read-write · current the Forwarding queue to use for packets in this forwarding class: Forwarding Queues are numbered starting from 0 to N (Forwarding Queue 0 with lowest priority queue) | |||||
| SopticsIMNeSLAType | 1.3.6.1.4.1.637.54.1.1.5.1.48 | INTEGER | RW | ||
scalar · INTEGER · read-write · current opticsIMNeSLAType specifies 'on per NE basis' the type of ETS Traffic Descriptors to be applied on each board in 'multi-board NE' supporting multi-board Link Aggregation Interface. In case of full opticsIMNeSLAType the same ETS Traffic Descriptor (for an ETS InFlow over a Link Aggregation Interface) is applied with full Traffic Descriptor Parameters(CIR,PIR) to each board supporting at least one Aggregation Port inside Link Aggregation Interface. In case of fractional opticsIMNeSLAType different instances of ETS Traffic Descriptor (for an ETS InFlow over a Link Aggregation Interface) are applied with fractional Traffic Descriptor Parameters(CIR,PIR) to each board supporting at least one Aggregation Port inside Link Aggregation Interface. Default value is full
| |||||
| SopticsimLinkOAMLogMinInterval | 1.3.6.1.4.1.637.54.1.1.5.1.49 | INTEGER (1..60) | RW | ||
scalar · INTEGER (1..60) · read-write · current This parameter defines the granularity window (sec) for the logging of LinkOAM event in the dot3OamEventLogTable. If more events of the same type are to be logged in this table in the window specified by this object, only the first one shall be logged. | |||||
| TopticsIMNeAlarmsTable | 1.3.6.1.4.1.637.54.1.1.5.1.52 | NA | |||
table · not-accessible · current Table for management of the ASAP object related to NE-level alarms. This table always contains only 1 single entry, with index value 1. | |||||
| RopticsIMNeAlarmsEntry | 1.3.6.1.4.1.637.54.1.1.5.1.52.1 | NA | |||
| CopticsIMNeAlarmsNeIndex | 1.3.6.1.4.1.637.54.1.1.5.1.52.1.1 | OpticsIMNeAlarmsNeIndex | NA | ||
column · OpticsIMNeAlarmsNeIndex · not-accessible · current Unique index for opticsIMNeAlarmsEntry. Only value 1 will be used. | |||||
| CopticsIMNeAlarmsAsapIndex | 1.3.6.1.4.1.637.54.1.1.5.1.52.1.2 | Integer32 | RW | ||
column · Integer32 · read-write · current This object contains the ASAP object associated to the NE. | |||||
| SopticsIMCfmStatus | 1.3.6.1.4.1.637.54.1.1.5.1.53 | INTEGER | RW | ||
scalar · INTEGER · read-write · current This object modifies the global enable status of CFM. The default is cfmDisable (0). In addition, when the status is disable, the first Maintenance Domain (MD) creation changes the status to enable, and when the status is enable, the last MD deletion changes the status to disable.
| |||||
| SopticsIMNeFrameSizeMode | 1.3.6.1.4.1.637.54.1.1.5.1.54 | INTEGER | RW | ||
scalar · INTEGER · read-write · current opticsIMNeFrameSizeMode specifies 'on per NE basis' the type of ingress
policer, egress shaper and Performance Monitoring counters to be applied
to all NE ports:
- native: Policer and Ingress Performance Monitoring counters are BOTH
based on NE-product specific value on Ingress Port Shaper and
Egress Performance Monitoring counters are BOTH based on
NE-product specific value on Egress Port
- layer1: Ingress Policer, Egress Shaper and Ingress/Egress Performance
Monitoring counters are based on Layer1
- layer2: Ingress Policer, Egress Shaper and Ingress/Egress Performance
Monitoring counters are based on Layer2.
Default value is NE-product specific
| |||||
| SopticsIMNeSyncEthEnable | 1.3.6.1.4.1.637.54.1.1.5.1.55 | TruthValue | RW | ||
scalar · TruthValue · read-write · current opticsIMNeSyncEthEnable specifies 'on per NE basis'enabled/disabled Ethernet Sync. Default value is false (Free running mode) | |||||
| TopticsIMCapabilityProfileTable | 1.3.6.1.4.1.637.54.1.1.5.1.56 | NA | |||
table · not-accessible · current This table contains a list of capability. | |||||
| RopticsIMCapabilityProfileEntry | 1.3.6.1.4.1.637.54.1.1.5.1.56.1 | NA | |||
row · not-accessible · current An entry of the opticsIMCapabilityProfileTable. | |||||
| CopticsIMCapabilityProfileProfIndex | 1.3.6.1.4.1.637.54.1.1.5.1.56.1.1 | OpticsIMcapabilityProfileIndex | NA | ||
column · OpticsIMcapabilityProfileIndex · not-accessible · current The value of this object is equal to opticsIMcapabilityProfileProfIndex in the opticsIMCapabilityProfileTable. | |||||
| CopticsIMCapabilityProfileCapIndex | 1.3.6.1.4.1.637.54.1.1.5.1.56.1.2 | OpticsIMCapabilityIndex | NA | ||
column · OpticsIMCapabilityIndex · not-accessible · current The value of this object is equal to opticsIMCapabilityProfileCapIndex in the opticsIMCapabilityProfileTable. | |||||
| CopticsIMCapabilityProfileCapUserLabel | 1.3.6.1.4.1.637.54.1.1.5.1.56.1.3 | OpticsIMUserLabel | RO | ||
column · OpticsIMUserLabel · read-only · current Name of the capability. List of possible values is defined in reference document | |||||
| CopticsIMCapabilityProfileCapInfo | 1.3.6.1.4.1.637.54.1.1.5.1.56.1.4 | OCTET STRING | RO | ||
column · OCTET STRING · read-only · current Information about capability. List of possible values is defined in reference document | |||||
| TopticsIMSwitchTable | 1.3.6.1.4.1.637.54.1.1.5.1.57 | NA | |||
table · not-accessible · current This table contains objects for each Switch Instannce . | |||||
| RopticsIMSwitchEntry | 1.3.6.1.4.1.637.54.1.1.5.1.57.1 | NA | |||
row · not-accessible · current An entry in this table represents an Ethernet Switch instance. It is autocreated/autodeleted by agent when a card is provisioned with switch instance
| |||||
| CopticsIMSwitchIndex | 1.3.6.1.4.1.637.54.1.1.5.1.57.1.1 | INTEGER | NA | ||
column · INTEGER · not-accessible · current The index for switch Table. | |||||
| CopticsIMSwitchID | 1.3.6.1.4.1.637.54.1.1.5.1.57.1.2 | INTEGER | RO | ||
column · INTEGER · read-only · current Uniquely identifies a Ethernet switch instance , the initial value starts from 0 . | |||||
| CopticsIMSwitchOperationMode | 1.3.6.1.4.1.637.54.1.1.5.1.57.1.3 | INTEGER | RW | ||
column · INTEGER · read-write · current Indicates what types of mechanism this Bridge perfoms. none (1) This NE cannot perform any bridge mechanism bridge8021D (2) This Bridge performs 802.1D mechanism and can not support VLAN bridge8021Q (3) This Bridge performs 802.1Q mechanism bridge8021ad (4) This Bridge performs 802.1ad mechanism. The default value is bridge8021ad(4).
| |||||
| CopticsIMSwitchEthOamBridgeMAC | 1.3.6.1.4.1.637.54.1.1.5.1.57.1.4 | MacAddress | RO | ||
column · MacAddress · read-only · current The MAC address of the Bridge that is used as ETH OAM messages MAC SA. | |||||
| CopticsIMSwitchEthOamLbmReplyTimeout | 1.3.6.1.4.1.637.54.1.1.5.1.57.1.5 | INTEGER | RW | ||
column · INTEGER · read-write · current The LBR timeout after the corresponding LBM has been sent. It is measured in seconds in the range [1-30], with default =5. | |||||
| CopticsIMSwitchEthOamLbmTxInterval | 1.3.6.1.4.1.637.54.1.1.5.1.57.1.6 | INTEGER | RW | ||
column · INTEGER · read-write · current The interval between two LBM frames sent. It is measured in 100 milli-second in the range [1-100]*100 ms, with default = 1second. | |||||
| CopticsIMSwitchLinkOAMLogMinInterval | 1.3.6.1.4.1.637.54.1.1.5.1.57.1.7 | INTEGER (1..60) | RW | ||
column · INTEGER (1..60) · read-write · current This parameter defines the granularity window (sec) for the logging of LinkOAM event in the dot3OamEventLogTable. If more events of the same type are to be logged in this table in the window specified by this object, only the first one shall be logged. The default value is product specific . | |||||
| CopticsIMSwitchPBProfile | 1.3.6.1.4.1.637.54.1.1.5.1.57.1.8 | INTEGER | RW | ||
column · INTEGER · read-write · current This object defines 'on per Switch basis' admitted Provider Bridge profiles with below values: - 5P3D (1) - Default value, - 8P0D (2), - 7P1D (3), - 6P2D (4), - Customer-defined profile1 (5) whose support is NE product specific | |||||
| CopticsIMSwitchTpAgingTime | 1.3.6.1.4.1.637.54.1.1.5.1.57.1.9 | Integer32 | RW | ||
column · Integer32 · read-write · current The timeout period in seconds (Range: 10..1000000) for aging out dynamically learned forwarding information. 802.1D-1998 recommends a default of 300 seconds. A value of 0x7FFFFFFF indicates aging disabled. | |||||
| CopticsIMSwitchTpLearnedEntryDiscards | 1.3.6.1.4.1.637.54.1.1.5.1.57.1.10 | Counter32 | RO | ||
column · Counter32 · read-only · current The total number of Forwarding Database entries, which have been or would have been learnt, but have been discarded due to a lack of space to store them in the Forwarding Database. If this counter is increasing, it indicates that the Forwarding Database is regularly becoming full (a condition which has unpleasant performance effects on the subnetwork). If this counter has a significant value but is not presently increasing, it indicates that the problem has been occurring but is not persistent. | |||||
| CopticsIMSwitchSTPType | 1.3.6.1.4.1.637.54.1.1.5.1.57.1.11 | INTEGER | RW | ||
column · INTEGER · read-write · current STP Type configuration: - manualDisable (1) is used to disable the protocol for the bridge - stp(2) is used to enable STP and synchronously the Rapid STP is disabled - rstp(3) is used to enable Rapid STP and synchronously STP is disabled - pervlanrstp(4) is used to enable per-VLAN RSTP - mstp(5) is used to enable RSTP-based MSTP - rstpPlus (6) is used to enable further optimization for RSTP - mstpPlus (7) is used to enable further optimization for MSTP. The default value is product specific .
| |||||
| CopticsIMSwitchCfmMaTableNextIndex | 1.3.6.1.4.1.637.54.1.1.5.1.57.1.12 | Gauge32 (0..4294967295) | RO | ||
column · Gauge32 (0..4294967295) · read-only · current Value to be used as the index of the MA table when the management entity wants to create a new row in the table. | |||||
| CopticsIMSwitchLocation | 1.3.6.1.4.1.637.54.1.1.5.1.57.1.13 | INTEGER | RO | ||
column · INTEGER · read-only · current it will be master slot in stack mode. RRSSBBDD RR- Rack SS- Subrack BB- Slot DD- Drawer. | |||||
| CopticsIMSwitchBridgeFilteringMode | 1.3.6.1.4.1.637.54.1.1.5.1.57.1.14 | INTEGER | RW | ||
column · INTEGER · read-write · current The Type of VLAN learning mode.When the object value is modified, the static fid-vlan mappings and static unicast entries need to be reconfigured. Static unicast configurations associated with old fid will get deleted. The default value is ivl(1) .
| |||||
| CopticsIMSwitchUserLabel | 1.3.6.1.4.1.637.54.1.1.5.1.57.1.15 | OpticsIMUserLabel | RW | ||
column · OpticsIMUserLabel · read-write · current The canonical name assigned to Switch Instance. | |||||
| TopticsIMSwitchPortTable | 1.3.6.1.4.1.637.54.1.1.5.1.58 | NA | |||
table · not-accessible · current This table contains Ethernet switch ports associated to each Ethernet switch instance. | |||||
| RopticsIMSwitchPortEntry | 1.3.6.1.4.1.637.54.1.1.5.1.58.1 | NA | |||
row · not-accessible · current An entry in this table represents an switch port. Being read-only table, it is autocreated by agent when an instance within opticsIMSwitchEntry is allocated with the port associated | |||||
| CopticsIMSwitchPortIndex | 1.3.6.1.4.1.637.54.1.1.5.1.58.1.1 | InterfaceIndex | NA | ||
column · InterfaceIndex · not-accessible · current The ifIndex value of the interface. | |||||
| CopticsIMSwitchPortMapStatus | 1.3.6.1.4.1.637.54.1.1.5.1.58.1.2 | INTEGER | RO | ||
column · INTEGER · read-only · current Switch Port Entry status. This object is always equal to 0. It is a dummy object needed to have something to retrieve | |||||
| NopticsIMTACACSServerManagement | 1.3.6.1.4.1.637.54.1.1.5.1.59 | ||||
| TopticsIMTACACSServerTable | 1.3.6.1.4.1.637.54.1.1.5.1.59.1 | NA | |||
table · not-accessible · current The TACACS server table. This table contains all the TACACS servers configured on the NE. | |||||
| RopticsIMTACACSServerEntry | 1.3.6.1.4.1.637.54.1.1.5.1.59.1.1 | NA | |||
row · not-accessible · current Entry is automatically created by Agent when a new TACACS server is configured on NE. | |||||
| CopticsIMTACACSServerIndex | 1.3.6.1.4.1.637.54.1.1.5.1.59.1.1.1 | Integer32 | NA | ||
column · Integer32 · not-accessible · current This is the index for the TACACS Server table. | |||||
| CopticsIMTACACSServerFailureCount | 1.3.6.1.4.1.637.54.1.1.5.1.59.1.1.2 | Integer32 | RO | ||
column · Integer32 · read-only · current This is the number of the tentative to access to this TACACS server with negative result. | |||||
| SopticsIMTACACSLastServerUsed | 1.3.6.1.4.1.637.54.1.1.5.1.59.2 | Integer32 | RO | ||
scalar · Integer32 · read-only · current This object reports the opticsIMTACACSServerIndex value of the last TACACS server reachable and used for Authentication/Authotization/Accounting access to the NE. | |||||
| SopticsIMTACACSAuthentication | 1.3.6.1.4.1.637.54.1.1.5.1.59.3 | INTEGER | RO | ||
scalar · INTEGER · read-only · current This object defines the actual user credential repository used for Authentication/Authotization/Accounting access to the NE.
| |||||
| TopticsIMRateLimitingProfileTable | 1.3.6.1.4.1.637.54.1.1.5.1.60 | NA | |||
table · not-accessible · current This table contains objects for a rate limiting profile of a NE interface. | |||||
| RopticsIMRateLimitingProfileEntry | 1.3.6.1.4.1.637.54.1.1.5.1.60.1 | NA | |||
row · not-accessible · current An entry references, on port basis, a rate limiting profile. | |||||
| CopticsIMRLProfileVlan | 1.3.6.1.4.1.637.54.1.1.5.1.60.1.1 | Unsigned32 (0..4097) | RW | ||
column · Unsigned32 (0..4097) · read-write · current The VLAN value associated to this profile. Values between 0 to 4095 indicate the actual VLAN field value. A value of 4096 indicates that the object refer to untagged frames, i.e. frames without 802.1Q field. A value of 4097 indicates that the VLAN field is not relevant, both if valued and if not present. | |||||
| CopticsIMRLProfilePCP | 1.3.6.1.4.1.637.54.1.1.5.1.60.1.2 | INTEGER | RW | ||
column · INTEGER · read-write · current The PCP value associated to this profile.
| |||||
| CopticsIMRLProfileCommittedRate | 1.3.6.1.4.1.637.54.1.1.5.1.60.1.3 | Gauge32 | RW | ||
column · Gauge32 · read-write · current The committed rate associated to this profile. | |||||
| CopticsIMRLProfileCommittedBurstSize | 1.3.6.1.4.1.637.54.1.1.5.1.60.1.4 | Gauge32 | RW | ||
column · Gauge32 · read-write · current The committed size associated to this profile. | |||||
| CopticsIMRLProfileRowStatus | 1.3.6.1.4.1.637.54.1.1.5.1.60.1.5 | RowStatus | RW | ||
column · RowStatus · read-write · current For creating and deleting this row. | |||||
| StsdimSnmpAgtIPv6Address | 1.3.6.1.4.1.637.54.1.1.5.1.61 | InetAddressIPv6 | RW | ||
scalar · InetAddressIPv6 · read-write · current This scalar object defines the Agent Ip Address in IPv6 format | |||||
| SopticsIMNeOverClockedModeEnable | 1.3.6.1.4.1.637.54.1.1.5.1.64 | TruthValue | RW | ||
scalar · TruthValue · read-write · current opticsIMNeOverClockedModeEnable specifies 'on per NE basis'enabled/disabled OverClocked Mode Default value is false (No over-clocked mode) | |||||
| SopticsIMNeAlarmAdmin | 1.3.6.1.4.1.637.54.1.1.5.1.65 | INTEGER | RW | ||
scalar · INTEGER · read-write · current opticsIMNeAlarmAdmin specifies 'on per NE basis' Alarm Admin value. Default value is mon(1)
| |||||
| SopticsIMIfQueueWREDAdminStatus | 1.3.6.1.4.1.637.54.1.1.5.1.66 | INTEGER | RW | ||
scalar · INTEGER · read-write · current opticsIMIfQueueWREDAdminStatus specifies the admin state for the WRED slope. If the opticsIMIfQueueWREDAdminStatus is set to 'down', the WRED slope is inactive. Default value is down
| |||||
| SopticsIMMaintenanceMode | 1.3.6.1.4.1.637.54.1.1.5.1.67 | INTEGER | RW | ||
scalar · INTEGER · read-write · current opticsIMNEMaintenanceMode set to 'enable' means the NE is entering in a Maintenance mode.
| |||||
| NtsdimSnmpNEMCConf | 1.3.6.1.4.1.637.54.1.1.99.2 | ||||
| NtsdimSnmpNEMCCompl | 1.3.6.1.4.1.637.54.1.1.99.2.1 | ||||
| MtsdimSnmpNEMc | 1.3.6.1.4.1.637.54.1.1.99.2.1.1 | ||||
compliance · current This module compliance describes a set of objects required for TSD-IM SNMP Agent implementation. These objects are defined inside tsdimSnmpNEMib | |||||
| NtsdimSnmpNEMCGroup | 1.3.6.1.4.1.637.54.1.1.99.2.2 | ||||
| GtsdimSnmpNEGroup | 1.3.6.1.4.1.637.54.1.1.99.2.2.1 | ||||
group · current This group describes the objects needed for the SNMP NE Configuration.
| |||||
| GtsdimLacSupportGroup | 1.3.6.1.4.1.637.54.1.1.99.2.2.6 | ||||
group · current This group describes the objects needed for Lac Configuration. | |||||
| GopticsIMACDGroup | 1.3.6.1.4.1.637.54.1.1.99.2.2.7 | ||||
group · current This group describes the objects needed for the resource assignment functionality.
| |||||
| GopticsIMIfExtGroup | 1.3.6.1.4.1.637.54.1.1.99.2.2.8 | ||||
group · current A collection of objects providing extensions for the configuration of an interface. | |||||
| GopticsIMAlarmGroup | 1.3.6.1.4.1.637.54.1.1.99.2.2.9 | ||||
group · current This group describes the alarm notifications | |||||
| GopticsIMTptCoordinatorGroup | 1.3.6.1.4.1.637.54.1.1.99.2.2.10 | ||||
group · current A collection of objects providing configuration information for the TPT Coordinator objects. | |||||
| GopticsIMNeConfigurationGroup | 1.3.6.1.4.1.637.54.1.1.99.2.2.11 | ||||
group · current This group describes the objects needed for NE configuration.
| |||||
| GopticsIMSnmpNETimeGroup | 1.3.6.1.4.1.637.54.1.1.99.2.2.12 | ||||
group · current This group describes the object used to manage the NE time, when NTP is not supported.
| |||||
| GopticsIMNTPGroup | 1.3.6.1.4.1.637.54.1.1.99.2.2.13 | ||||
group · current This group describes the objects related to the NTP management. | |||||
| GopticsIMOptAlarmGroup | 1.3.6.1.4.1.637.54.1.1.99.2.2.14 | ||||
group · current This group describes the alarm notifications
| |||||
| GopticsIMNePMCollectionGroup | 1.3.6.1.4.1.637.54.1.1.99.2.2.15 | ||||
group · current This group describes the objects needed for NE PM Collection. | |||||
Textual conventions
OpticsIMCapabilityIndexUnsigned32 (1..2147483647)Capability index. Each capability has a unique index defined by reference comumentation.
OpticsIMHashingKeyListBitsalllabels(6)bottomlabel(7)cpri(3)cvid(2)etype(15)ipDestAddr(8)ipDestPortNumber(10)ipDscp(12)ipSourceAddr(9)ipSourcePortNumber(11)ipcp(14)isid(13)macDestAddr(0)macSourceAddr(1)spri(5)svid(4)Each Hashing key parameter as input to Link Aggregation Hash function is represented by a single bit within the value of this object. Only the first 13 bits are defined (from 0 to 12); the remaining bits (from 13 to 31) have not been defined yet. Following the list of the actual hashing key parameters: 1) bit 0: MAC Destination Address (48 bits) 2) bit 1: MAC Source Address (48 bits) 3) bit 2: C-VID (12 bits) 4) bit 3: C-PRI (3 bits) 5) bit 4: S-VID (12 bits) 6) bit 5: S-PRI (3 bits) 7) bit 6: All MPLS Labels (N labels*20 bits) 8) bit 7: lowest MPLS Label (MPLS label with 1 Bottom of Stack bit) 9) bit 8: IP Destination Address (32 bits) 10) bit 9: IP Source Address (32 bits) 11) bit 10: Destination Port Number (16 Bits) 12) bit 11: Source Port Number (16 Bits) 13) bit 12: IP DSCP (6 bits) 14) bit 13: I-SID (24 bits) 15) bit 14: I-PCP (3 bits) 16) bit 15: Ethertype (32 bit)
OpticsIMMibConfigurationModeINTEGERoffline(0)online(1)The value of this object identifies the mode of the MIB Configuration.
OpticsIMMngInterfaceAddressTypeINTEGERipAddress(0)presentationAddress(1)The value of this object identifies the Address Type of the management interface.
OpticsIMMngInterfaceCharacterizationINTEGERprimary(0)secondary(1)The value of this object identifies the Characterization of the management interface.
OpticsIMMngInterfaceTypeINTEGERcli(3)http(4)q3(0)snmp(1)tl1(2)The value of this object identifies the Type of the management interface.
OpticsIMNeAlarmsNeIndexUnsigned32 (1..4294967295)A value used to index the NE alarms ASAP object table
OpticsIMcapabilityProfileIndexUnsigned32 (1..2147483647)Capability profile index. NE unique index.
PortListOCTET STRINGEach octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'.
Traps / Notifications
- opticsIMAlarm1588AnnouncePktLOSClear
1.3.6.1.4.1.637.54.1.1.5.1.40.212 - opticsIMAlarm1588AnnouncePktLOSRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.211 - opticsIMAlarm1588DelayRespPktLOSClear
1.3.6.1.4.1.637.54.1.1.5.1.40.216 - opticsIMAlarm1588DelayRespPktLOSRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.215 - opticsIMAlarm1588PTPClockclassDEGClear
1.3.6.1.4.1.637.54.1.1.5.1.40.218 - opticsIMAlarm1588PTPClockclassDEGRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.217 - opticsIMAlarm1588SyncPktLOSClear
1.3.6.1.4.1.637.54.1.1.5.1.40.214 - opticsIMAlarm1588SyncPktLOSRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.213 - opticsIMAlarm1PpsToDDEGClear
1.3.6.1.4.1.637.54.1.1.5.1.40.190 - opticsIMAlarm1PpsToDDEGRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.189 - opticsIMAlarm1PpsTodLOSClear
1.3.6.1.4.1.637.54.1.1.5.1.40.188 - opticsIMAlarm1PpsTodLOSRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.187 - opticsIMAlarmACMDegradeClear
1.3.6.1.4.1.637.54.1.1.5.1.40.294 - opticsIMAlarmACMDegradeRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.293 - opticsIMAlarmAisClear
1.3.6.1.4.1.637.54.1.1.5.1.40.6 - opticsIMAlarmAisRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.5 - opticsIMAlarmAisRxClear
1.3.6.1.4.1.637.54.1.1.5.1.40.174 - opticsIMAlarmAisRxRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.173 - opticsIMAlarmAisTxClear
1.3.6.1.4.1.637.54.1.1.5.1.40.172 - opticsIMAlarmAisTxRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.171 - opticsIMAlarmBandwidthDegradeForProtectionSwitchClear
1.3.6.1.4.1.637.54.1.1.5.1.40.200 - opticsIMAlarmBandwidthDegradeForProtectionSwitchRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.199 - opticsIMAlarmCRNGConditionalSelfTestFailClear
1.3.6.1.4.1.637.54.1.1.5.1.40.284 - opticsIMAlarmCRNGConditionalSelfTestFailRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.283 - opticsIMAlarmCableLOSClear
1.3.6.1.4.1.637.54.1.1.5.1.40.14 - opticsIMAlarmCableLOSRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.13 - opticsIMAlarmDegradeClear
1.3.6.1.4.1.637.54.1.1.5.1.40.72 - opticsIMAlarmDegradeRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.71 - opticsIMAlarmDemFailClear
1.3.6.1.4.1.637.54.1.1.5.1.40.22 - opticsIMAlarmDemFailRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.21 - opticsIMAlarmDemLOSClear
1.3.6.1.4.1.637.54.1.1.5.1.40.20 - opticsIMAlarmDemLOSRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.19 - opticsIMAlarmDuplicatedAddressDetectedClear
1.3.6.1.4.1.637.54.1.1.5.1.40.202 - opticsIMAlarmDuplicatedAddressDetectedRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.201 - opticsIMAlarmESMCPktLosClear
1.3.6.1.4.1.637.54.1.1.5.1.40.220 - opticsIMAlarmESMCPktLosRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.219 - opticsIMAlarmEthOAMMACStatusDefectClear
1.3.6.1.4.1.637.54.1.1.5.1.40.268 - opticsIMAlarmEthOAMMACStatusDefectRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.267 - opticsIMAlarmEthOAMUnexpectedCcmConnectivityClear
1.3.6.1.4.1.637.54.1.1.5.1.40.278 - opticsIMAlarmEthOAMUnexpectedCcmConnectivityRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.277 - opticsIMAlarmEthOAMUnexpectedMepClear
1.3.6.1.4.1.637.54.1.1.5.1.40.266 - opticsIMAlarmEthOAMUnexpectedMepRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.265 - opticsIMAlarmExSERClear
1.3.6.1.4.1.637.54.1.1.5.1.40.166 - opticsIMAlarmExSERRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.165 - opticsIMAlarmExcessivepacketLossClear
1.3.6.1.4.1.637.54.1.1.5.1.40.184 - opticsIMAlarmExcessivepacketLossRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.183 - opticsIMAlarmExstensionHeaderMismatchClear
1.3.6.1.4.1.637.54.1.1.5.1.40.68 - opticsIMAlarmExstensionHeaderMismatchRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.67 - opticsIMAlarmIncompatibleProtectionClear
1.3.6.1.4.1.637.54.1.1.5.1.40.198 - opticsIMAlarmIncompatibleProtectionRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.197 - opticsIMAlarmInvalidTdmDataClear
1.3.6.1.4.1.637.54.1.1.5.1.40.196 - opticsIMAlarmInvalidTdmDataRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.195 - opticsIMAlarmIpsecPskMissingClear
1.3.6.1.4.1.637.54.1.1.5.1.40.272 - opticsIMAlarmIpsecPskMissingRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.271 - opticsIMAlarmIpsecTunnelSetupFailureClear
1.3.6.1.4.1.637.54.1.1.5.1.40.274 - opticsIMAlarmIpsecTunnelSetupFailureRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.273 - opticsIMAlarmLAPDFailClear
1.3.6.1.4.1.637.54.1.1.5.1.40.42 - opticsIMAlarmLAPDFailRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.41 - opticsIMAlarmLinkCleClear
1.3.6.1.4.1.637.54.1.1.5.1.40.110 - opticsIMAlarmLinkCleRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.109 - opticsIMAlarmLinkOdncClear
1.3.6.1.4.1.637.54.1.1.5.1.40.108 - opticsIMAlarmLinkOdncRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.107 - opticsIMAlarmLinkSiClear
1.3.6.1.4.1.637.54.1.1.5.1.40.112 - opticsIMAlarmLinkSiRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.111 - opticsIMAlarmLocalAutoTxMuteClear
1.3.6.1.4.1.637.54.1.1.5.1.40.296 - opticsIMAlarmLocalAutoTxMuteRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.295 - opticsIMAlarmLogUploadFailureClear
1.3.6.1.4.1.637.54.1.1.5.1.40.270 - opticsIMAlarmLogUploadFailureRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.269 - opticsIMAlarmLoopbackPresenceClear
1.3.6.1.4.1.637.54.1.1.5.1.40.204 - opticsIMAlarmLoopbackPresenceRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.203 - opticsIMAlarmLossOfAlignmentClear
1.3.6.1.4.1.637.54.1.1.5.1.40.48 - opticsIMAlarmLossOfAlignmentRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.47 - opticsIMAlarmLossOfCESoETHFrameClear
1.3.6.1.4.1.637.54.1.1.5.1.40.168 - opticsIMAlarmLossOfCESoETHFrameRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.167 - opticsIMAlarmLossOfContinuityClear
1.3.6.1.4.1.637.54.1.1.5.1.40.298 - opticsIMAlarmLossOfContinuityRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.297 - opticsIMAlarmLossOfESMCClear
1.3.6.1.4.1.637.54.1.1.5.1.40.180 - opticsIMAlarmLossOfESMCRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.179 - opticsIMAlarmLossOfFrameClear
1.3.6.1.4.1.637.54.1.1.5.1.40.4 - opticsIMAlarmLossOfFrameRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.3 - opticsIMAlarmLossOfMultiframeClear
1.3.6.1.4.1.637.54.1.1.5.1.40.60 - opticsIMAlarmLossOfMultiframeRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.59 - opticsIMAlarmLossOfPointerClear
1.3.6.1.4.1.637.54.1.1.5.1.40.58 - opticsIMAlarmLossOfPointerRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.57 - opticsIMAlarmLossOfSignalClear
1.3.6.1.4.1.637.54.1.1.5.1.40.2 - opticsIMAlarmLossOfSignalRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.1 - opticsIMAlarmMissingDiversityAlignConfClear
1.3.6.1.4.1.637.54.1.1.5.1.40.292 - opticsIMAlarmMissingDiversityAlignConfRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.291 - opticsIMAlarmModFailClear
1.3.6.1.4.1.637.54.1.1.5.1.40.26 - opticsIMAlarmModFailRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.25 - opticsIMAlarmModLOSClear
1.3.6.1.4.1.637.54.1.1.5.1.40.24 - opticsIMAlarmModLOSRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.23 - opticsIMAlarmPPPFailClear
1.3.6.1.4.1.637.54.1.1.5.1.40.50 - opticsIMAlarmPPPFailRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.49 - opticsIMAlarmPlmClear
1.3.6.1.4.1.637.54.1.1.5.1.40.38 - opticsIMAlarmPlmRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.37 - opticsIMAlarmPowerSavingActiveClear
1.3.6.1.4.1.637.54.1.1.5.1.40.300 - opticsIMAlarmPowerSavingActiveRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.299 - opticsIMAlarmPtpFaultyClear
1.3.6.1.4.1.637.54.1.1.5.1.40.194 - opticsIMAlarmPtpFaultyRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.193 - opticsIMAlarmPtpLossOfLockClear
1.3.6.1.4.1.637.54.1.1.5.1.40.192 - opticsIMAlarmPtpLossOfLockRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.191 - opticsIMAlarmRemoteDefectIndicationClear
1.3.6.1.4.1.637.54.1.1.5.1.40.12 - opticsIMAlarmRemoteDefectIndicationRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.11 - opticsIMAlarmRemoteFaultIndicationClear
1.3.6.1.4.1.637.54.1.1.5.1.40.210 - opticsIMAlarmRemoteFaultIndicationRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.209 - opticsIMAlarmRemoteNEFailureClear
1.3.6.1.4.1.637.54.1.1.5.1.40.52 - opticsIMAlarmRemoteNEFailureRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.51 - opticsIMAlarmRemotepacketlossClear
1.3.6.1.4.1.637.54.1.1.5.1.40.186 - opticsIMAlarmRemotepacketlossRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.185 - opticsIMAlarmRxFailClear
1.3.6.1.4.1.637.54.1.1.5.1.40.18 - opticsIMAlarmRxFailRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.17 - opticsIMAlarmRxLOSClear
1.3.6.1.4.1.637.54.1.1.5.1.40.16 - opticsIMAlarmRxLOSRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.15 - opticsIMAlarmSWDLConditionalSelfTestFailClear
1.3.6.1.4.1.637.54.1.1.5.1.40.282 - opticsIMAlarmSWDLConditionalSelfTestFailRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.281 - opticsIMAlarmSecureModeMismatchClear
1.3.6.1.4.1.637.54.1.1.5.1.40.280 - opticsIMAlarmSecureModeMismatchRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.279 - opticsIMAlarmSecureSelfTestFailureClear
1.3.6.1.4.1.637.54.1.1.5.1.40.276 - opticsIMAlarmSecureSelfTestFailureRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.275 - opticsIMAlarmSequenceMismatchClear
1.3.6.1.4.1.637.54.1.1.5.1.40.62 - opticsIMAlarmSequenceMismatchRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.61 - opticsIMAlarmServerSignalFailClear
1.3.6.1.4.1.637.54.1.1.5.1.40.64 - opticsIMAlarmServerSignalFailRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.63 - opticsIMAlarmServiceSelectiveDropClear
1.3.6.1.4.1.637.54.1.1.5.1.40.206 - opticsIMAlarmServiceSelectiveDropRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.205 - opticsIMAlarmStolenStatusClear
1.3.6.1.4.1.637.54.1.1.5.1.40.264 - opticsIMAlarmStolenStatusRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.263 - opticsIMAlarmStraypacketsClear
1.3.6.1.4.1.637.54.1.1.5.1.40.182 - opticsIMAlarmStraypacketsRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.181 - opticsIMAlarmTCAClear
1.3.6.1.4.1.637.54.1.1.5.1.40.32 - opticsIMAlarmTCARaise
1.3.6.1.4.1.637.54.1.1.5.1.40.31 - opticsIMAlarmTransmitterDegradedClear
1.3.6.1.4.1.637.54.1.1.5.1.40.10 - opticsIMAlarmTransmitterDegradedRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.9 - opticsIMAlarmTransmitterFailureClear
1.3.6.1.4.1.637.54.1.1.5.1.40.8 - opticsIMAlarmTransmitterFailureRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.7 - opticsIMAlarmTsfClear
1.3.6.1.4.1.637.54.1.1.5.1.40.36 - opticsIMAlarmTsfRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.35 - opticsIMAlarmTxFailClear
1.3.6.1.4.1.637.54.1.1.5.1.40.30 - opticsIMAlarmTxFailRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.29 - opticsIMAlarmTxLOSClear
1.3.6.1.4.1.637.54.1.1.5.1.40.28 - opticsIMAlarmTxLOSRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.27 - opticsIMAlarmUnavailableTimeClear
1.3.6.1.4.1.637.54.1.1.5.1.40.34 - opticsIMAlarmUnavailableTimeRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.33 - opticsIMAlarmUnequippedClear
1.3.6.1.4.1.637.54.1.1.5.1.40.66 - opticsIMAlarmUnequippedRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.65 - opticsIMAlarmUpdateIPSecKeysFailClear
1.3.6.1.4.1.637.54.1.1.5.1.40.286 - opticsIMAlarmUpdateIPSecKeysFailRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.285 - opticsIMAlarmUrdClear
1.3.6.1.4.1.637.54.1.1.5.1.40.176 - opticsIMAlarmUrdRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.175 - opticsIMAlarmUruClear
1.3.6.1.4.1.637.54.1.1.5.1.40.40 - opticsIMAlarmUruRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.39 - opticsIMAlarmUrusClear
1.3.6.1.4.1.637.54.1.1.5.1.40.178 - opticsIMAlarmUrusRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.177 - opticsIMAlarmUserPayloadMismatchClear
1.3.6.1.4.1.637.54.1.1.5.1.40.70 - opticsIMAlarmUserPayloadMismatchRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.69 - opticsIMAlarmVESListenerConnectionFailureClear
1.3.6.1.4.1.637.54.1.1.5.1.40.290 - opticsIMAlarmVESListenerConnectionFailureRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.289 - opticsIMAlarmZeroizeIPSecKeysFailClear
1.3.6.1.4.1.637.54.1.1.5.1.40.288 - opticsIMAlarmZeroizeIPSecKeysFailRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.287 - opticsIMMemoryCardForbiddenToUseClear
1.3.6.1.4.1.637.54.1.1.5.1.40.106 - opticsIMMemoryCardForbiddenToUseRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.105 - opticsIMRetimingBufferOverflowClear
1.3.6.1.4.1.637.54.1.1.5.1.40.152 - opticsIMRetimingBufferOverflowRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.151 - opticsimAlarm1588TCFailClear
1.3.6.1.4.1.637.54.1.1.5.1.40.226 - opticsimAlarm1588TCFailRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.225 - opticsimAlarmAesFipsFailureClear
1.3.6.1.4.1.637.54.1.1.5.1.40.242 - opticsimAlarmAesFipsFailureRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.241 - opticsimAlarmAutomaticEthShutdownClear
1.3.6.1.4.1.637.54.1.1.5.1.40.122 - opticsimAlarmAutomaticEthShutdownRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.121 - opticsimAlarmCKMClear
1.3.6.1.4.1.637.54.1.1.5.1.40.238 - opticsimAlarmCKMRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.237 - opticsimAlarmClockFailureClear
1.3.6.1.4.1.637.54.1.1.5.1.40.116 - opticsimAlarmClockFailureRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.115 - opticsimAlarmESMClear
1.3.6.1.4.1.637.54.1.1.5.1.40.256 - opticsimAlarmESMRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.255 - opticsimAlarmEthANMClear
1.3.6.1.4.1.637.54.1.1.5.1.40.136 - opticsimAlarmEthANMRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.135 - opticsimAlarmEthFOPAMClear
1.3.6.1.4.1.637.54.1.1.5.1.40.130 - opticsimAlarmEthFOPAMRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.129 - opticsimAlarmEthFOPCMClear
1.3.6.1.4.1.637.54.1.1.5.1.40.124 - opticsimAlarmEthFOPCMRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.123 - opticsimAlarmEthFOPDMClear
1.3.6.1.4.1.637.54.1.1.5.1.40.132 - opticsimAlarmEthFOPDMRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.131 - opticsimAlarmEthFOPNRClear
1.3.6.1.4.1.637.54.1.1.5.1.40.128 - opticsimAlarmEthFOPNRRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.127 - opticsimAlarmEthFOPPMClear
1.3.6.1.4.1.637.54.1.1.5.1.40.126 - opticsimAlarmEthFOPPMRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.125 - opticsimAlarmEthNOSYNCRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.133 - opticsimAlarmEthNOSYNClear
1.3.6.1.4.1.637.54.1.1.5.1.40.134 - opticsimAlarmEthOAMLossOfContinuityClear
1.3.6.1.4.1.637.54.1.1.5.1.40.92 - opticsimAlarmEthOAMLossOfContinuityRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.91 - opticsimAlarmEthOAMMIPOverflowEventClear
1.3.6.1.4.1.637.54.1.1.5.1.40.160 - opticsimAlarmEthOAMMIPOverflowEventRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.159 - opticsimAlarmEthOAMMisMergeConditionClear
1.3.6.1.4.1.637.54.1.1.5.1.40.94 - opticsimAlarmEthOAMMisMergeConditionRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.93 - opticsimAlarmEthOAMRDIClear
1.3.6.1.4.1.637.54.1.1.5.1.40.102 - opticsimAlarmEthOAMRDIRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.101 - opticsimAlarmEthOAMUNPrClear
1.3.6.1.4.1.637.54.1.1.5.1.40.114 - opticsimAlarmEthOAMUNPrRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.113 - opticsimAlarmEthOAMUnexpectedLevelClear
1.3.6.1.4.1.637.54.1.1.5.1.40.100 - opticsimAlarmEthOAMUnexpectedLevelRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.99 - opticsimAlarmEthOAMUnexpectedMepIdClear
1.3.6.1.4.1.637.54.1.1.5.1.40.96 - opticsimAlarmEthOAMUnexpectedMepIdRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.95 - opticsimAlarmEthOAMUnexpectedPeriodClear
1.3.6.1.4.1.637.54.1.1.5.1.40.98 - opticsimAlarmEthOAMUnexpectedPeriodRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.97 - opticsimAlarmEthOAMVSFClear
1.3.6.1.4.1.637.54.1.1.5.1.40.164 - opticsimAlarmEthOAMVSFRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.163 - opticsimAlarmEthPNACClear
1.3.6.1.4.1.637.54.1.1.5.1.40.120 - opticsimAlarmEthPNACRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.119 - opticsimAlarmEthSignalDegradeClear
1.3.6.1.4.1.637.54.1.1.5.1.40.118 - opticsimAlarmEthSignalDegradedRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.117 - opticsimAlarmExcessiveMissingPktClear
1.3.6.1.4.1.637.54.1.1.5.1.40.224 - opticsimAlarmExcessiveMissingPktRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.223 - opticsimAlarmFailureOfProtocolProvisioningMismatchClear
1.3.6.1.4.1.637.54.1.1.5.1.40.154 - opticsimAlarmFailureOfProtocolProvisioningMismatchRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.153 - opticsimAlarmFailureOfProtocolTimeOutClear
1.3.6.1.4.1.637.54.1.1.5.1.40.156 - opticsimAlarmFailureOfProtocolTimeOutRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.155 - opticsimAlarmHldOverClear
1.3.6.1.4.1.637.54.1.1.5.1.40.138 - opticsimAlarmHldOverRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.137 - opticsimAlarmInputPowerDegradeClear
1.3.6.1.4.1.637.54.1.1.5.1.40.74 - opticsimAlarmInputPowerDegradeRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.73 - opticsimAlarmJitterBufferOverrunClear
1.3.6.1.4.1.637.54.1.1.5.1.40.82 - opticsimAlarmJitterBufferOverrunRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.81 - opticsimAlarmJitterBufferUnderrunClear
1.3.6.1.4.1.637.54.1.1.5.1.40.84 - opticsimAlarmJitterBufferUnderrunRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.83 - opticsimAlarmKeyUnavailableClear
1.3.6.1.4.1.637.54.1.1.5.1.40.258 - opticsimAlarmKeyUnavailableRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.257 - opticsimAlarmLagPortDownClear
1.3.6.1.4.1.637.54.1.1.5.1.40.236 - opticsimAlarmLagPortDownRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.235 - opticsimAlarmLateFramesClear
1.3.6.1.4.1.637.54.1.1.5.1.40.78 - opticsimAlarmLateFramesRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.77 - opticsimAlarmLoopingFrameEventClear
1.3.6.1.4.1.637.54.1.1.5.1.40.158 - opticsimAlarmLoopingFrameEventRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.157 - opticsimAlarmLossOfPktSynchronizationClear
1.3.6.1.4.1.637.54.1.1.5.1.40.222 - opticsimAlarmLossOfPktSynchronizationRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.221 - opticsimAlarmLossOfProtectionClear
1.3.6.1.4.1.637.54.1.1.5.1.40.170 - opticsimAlarmLossOfProtectionRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.169 - opticsimAlarmMalformedFramesClear
1.3.6.1.4.1.637.54.1.1.5.1.40.80 - opticsimAlarmMalformedFramesRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.79 - opticsimAlarmMcastTableOverflowEventClear
1.3.6.1.4.1.637.54.1.1.5.1.40.162 - opticsimAlarmMcastTableOverflowEventRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.161 - opticsimAlarmMisconnectionClear
1.3.6.1.4.1.637.54.1.1.5.1.40.76 - opticsimAlarmMisconnectionRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.75 - opticsimAlarmNKMClear
1.3.6.1.4.1.637.54.1.1.5.1.40.240 - opticsimAlarmNKMRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.239 - opticsimAlarmPDHMNDClear
1.3.6.1.4.1.637.54.1.1.5.1.40.150 - opticsimAlarmPDHMNDRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.149 - opticsimAlarmPDHPLCRClear
1.3.6.1.4.1.637.54.1.1.5.1.40.148 - opticsimAlarmPDHPLCRRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.147 - opticsimAlarmPDHPLCTClear
1.3.6.1.4.1.637.54.1.1.5.1.40.146 - opticsimAlarmPDHPLCTRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.145 - opticsimAlarmPDHTLCRClear
1.3.6.1.4.1.637.54.1.1.5.1.40.142 - opticsimAlarmPDHTLCRRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.141 - opticsimAlarmPDHTLCTClear
1.3.6.1.4.1.637.54.1.1.5.1.40.144 - opticsimAlarmPDHTLCTRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.143 - opticsimAlarmRxProblemClear
1.3.6.1.4.1.637.54.1.1.5.1.40.232 - opticsimAlarmRxProblemRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.231 - opticsimAlarmServerSignalEgreFailClear
1.3.6.1.4.1.637.54.1.1.5.1.40.88 - opticsimAlarmServerSignalEgreFailRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.87 - opticsimAlarmServerSignalIngrFailClear
1.3.6.1.4.1.637.54.1.1.5.1.40.86 - opticsimAlarmServerSignalIngrFailRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.85 - opticsimAlarmSessionTimeoutClear
1.3.6.1.4.1.637.54.1.1.5.1.40.244 - opticsimAlarmSessionTimeoutRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.243 - opticsimAlarmSynchronizationSignalFailClear
1.3.6.1.4.1.637.54.1.1.5.1.40.104 - opticsimAlarmSynchronizationSignalFailRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.103 - opticsimAlarmTrafficDisableClear
1.3.6.1.4.1.637.54.1.1.5.1.40.90 - opticsimAlarmTrafficDisableRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.89 - opticsimAlarmTrafficDownClear
1.3.6.1.4.1.637.54.1.1.5.1.40.228 - opticsimAlarmTrafficDownRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.227 - opticsimAlarmTrafficLossClear
1.3.6.1.4.1.637.54.1.1.5.1.40.230 - opticsimAlarmTrafficLossRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.229 - opticsimAlarmTxProblemClear
1.3.6.1.4.1.637.54.1.1.5.1.40.234 - opticsimAlarmTxProblemRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.233 - opticsimAlarmlnkaggExBandwidthDegradeClear
1.3.6.1.4.1.637.54.1.1.5.1.40.208 - opticsimAlarmlnkaggExBandwidthDegradeRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.207 - opticsimClientSignalFailClear
1.3.6.1.4.1.637.54.1.1.5.1.40.56 - opticsimClientSignalFailRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.55 - opticsimDAAlarmDACMClear
1.3.6.1.4.1.637.54.1.1.5.1.40.46 - opticsimDAAlarmDACMRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.45 - opticsimFreeLicenseExpiredClear
1.3.6.1.4.1.637.54.1.1.5.1.40.262 - opticsimFreeLicenseExpiredRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.261 - opticsimFreeLicenseRunningClear
1.3.6.1.4.1.637.54.1.1.5.1.40.260 - opticsimFreeLicenseRunningRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.259 - opticsimGfpAlarmGtmClear
1.3.6.1.4.1.637.54.1.1.5.1.40.44 - opticsimGfpAlarmGtmRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.43 - opticsimInputPowerOverloadClear
1.3.6.1.4.1.637.54.1.1.5.1.40.254 - opticsimInputPowerOverloadRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.253 - opticsimSdhConcDegradeClear
1.3.6.1.4.1.637.54.1.1.5.1.40.54 - opticsimSdhConcDegradeRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.53 - opticsimTLUClear
1.3.6.1.4.1.637.54.1.1.5.1.40.140 - opticsimTLURaise
1.3.6.1.4.1.637.54.1.1.5.1.40.139 - opticsimThresholdInputPowerHighClear
1.3.6.1.4.1.637.54.1.1.5.1.40.250 - opticsimThresholdInputPowerHighRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.249 - opticsimThresholdInputPowerLowClear
1.3.6.1.4.1.637.54.1.1.5.1.40.252 - opticsimThresholdInputPowerLowRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.251 - opticsimThresholdOutputPowerHighClear
1.3.6.1.4.1.637.54.1.1.5.1.40.246 - opticsimThresholdOutputPowerHighRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.245 - opticsimThresholdOutputPowerLowClear
1.3.6.1.4.1.637.54.1.1.5.1.40.248 - opticsimThresholdOutputPowerLowRaise
1.3.6.1.4.1.637.54.1.1.5.1.40.247 - tsdimAlarmPlmClear
1.3.6.1.4.1.637.54.1.1.5.1.21 - tsdimAlarmPlmRaise
1.3.6.1.4.1.637.54.1.1.5.1.20 - tsdimAlarmTsfClear
1.3.6.1.4.1.637.54.1.1.5.1.24 - tsdimAlarmTsfRaise
1.3.6.1.4.1.637.54.1.1.5.1.23