OPTICSIM-RADIO-TRS-PDH-MIB
Nokia (formerly 'Alcatel-Lucent')Radio PDH Transmission MIB.
snmptranslate -m OPTICSIM-RADIO-TRS-PDH-MIB -Tpsnmpwalk -v2c -c <community> -m OPTICSIM-RADIO-TRS-PDH-MIB <host> 1.3.6.1.4.1.637.54.1.10.3Imports
| IF-MIB | InterfaceIndex, InterfaceIndexOrZero, ifIndex |
|---|---|
| OPTICSIM-COMMON-TC | OpticsIMRadioChannelNumber |
| OPTICSIM-RADIOREG-MIB | opticsimRadioMC, opticsimRadioMib |
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP |
| SNMPv2-SMI | Bits, Integer32, IpAddress, MODULE-IDENTITY, MibIdentifier, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, iso |
| SNMPv2-TC | DisplayString, PhysAddress, RowStatus, TEXTUAL-CONVENTION, TruthValue |
| TSDIM-SNMP-TC | OpticsIMUserLabel, TsdimOperationalState |
OID tree
| Name | OID | Type | Access | Status |
|---|---|---|---|---|
| IopticsIMRadioTrsPdhMib | 1.3.6.1.4.1.637.54.1.10.3 | |||
identity Radio PDH Transmission MIB. | ||||
| NopticsIMRadioTrsPdhMibObject | 1.3.6.1.4.1.637.54.1.10.3.1 | |||
| TopticsIMRadioPDHTTPBidTable | 1.3.6.1.4.1.637.54.1.10.3.1.1 | NA | ||
table · not-accessible · current This table represents the process of converting the incoming radio frequency signal into an internal logic level PDH signal and vice-versa. This process is composed of different subfunctions: Rx and Demodulation subfunctions in sink side, Tx and Modulation subfunctions in source side. | ||||
| RopticsIMRadioPDHTTPBidEntry | 1.3.6.1.4.1.637.54.1.10.3.1.1.1 | NA | ||
row · not-accessible · current An entry of the radioPDHTTPBidTable table. Each entry corresponds to a Radio Plesiochronous Physical Interface (RPPI).
| ||||
| CradioPDHTTPBidRadioChannelNumber | 1.3.6.1.4.1.637.54.1.10.3.1.1.1.1 | OpticsIMRadioChannelNumber | RO | |
column · OpticsIMRadioChannelNumber · read-only · current See Textual Conventions. | ||||
| CradioPDHTTPBidModulation | 1.3.6.1.4.1.637.54.1.10.3.1.1.1.2 | OpticsIMModulationType | RW | |
column · OpticsIMModulationType · read-write · current This object specifies the type of modulation. | ||||
| CradioPDHTTPBidODUServiceKit | 1.3.6.1.4.1.637.54.1.10.3.1.1.1.4 | INTEGER | RO | |
column · INTEGER · read-only · current This object specifies if the ODU Service Kit is connected. When this is detected an Abnormal Condition indication is generated.
| ||||
| CradioPDHTTPBidOperationalState | 1.3.6.1.4.1.637.54.1.10.3.1.1.1.5 | TsdimOperationalState | RO | |
column · TsdimOperationalState · read-only · current See Textual Conventions. | ||||
| CradioPDHTTPBidAsapIndex | 1.3.6.1.4.1.637.54.1.10.3.1.1.1.6 | Integer32 | RW | |
column · Integer32 · read-write · current This object defines the ASAP object associated to this radio physical port. | ||||
| CradioPDHTTPBidEqualizerStatus | 1.3.6.1.4.1.637.54.1.10.3.1.1.1.7 | INTEGER | RW | |
column · INTEGER · read-write · current This object specifies the status of equalizer.
| ||||
| CradioPDHTTPBidModulationId | 1.3.6.1.4.1.637.54.1.10.3.1.1.1.8 | Integer32 | RW | |
column · Integer32 · read-write · current This object defines the identifier of the modulation value requested by the managing system. This identifier must be included in one of the entries of the opticsIMAllowedModulationTable. As a side effect of setting this object, the agent must set the radioPDHTTPBidModulation object with the value associated to this identifier. | ||||
| CradioPDHTTPBidCapacityId | 1.3.6.1.4.1.637.54.1.10.3.1.1.1.9 | Integer32 | RW | |
column · Integer32 · read-write · current This object defines the identifier of the radio capacity value requested by the managing system. This identifier must be included in one of the entries of the opticsIMAllowedCapacityTable. As a side effect of setting this object, the agent must set the radioPDHTTPBidcapacity object with the string associated to this identifier. | ||||
| CradioPDHTTPBidCapacity | 1.3.6.1.4.1.637.54.1.10.3.1.1.1.10 | DisplayString | RO | |
column · DisplayString · read-only · current This object specifies the radio capacity. | ||||
| CradioPDHTTPBidChannelSpacingId | 1.3.6.1.4.1.637.54.1.10.3.1.1.1.11 | Integer32 | RW | |
column · Integer32 · read-write · current This object defines the identifier of the channel spacing value requested by the managing system. This identifier must be included in one of the entries of the opticsIMAllowedChannelSpacingTable (pre-set modulation setting, adaptiveModulationMode 'false') or of the opticsIMAdaptiveAllowedChannelSpacingTable (adaptive modulation setting, adaptiveModulationMode 'true'). As a side effect of setting this object, the agent must set the radioPDHTTPBidChannelSpacing object with the value associated to this identifier. | ||||
| CradioPDHTTPBidChannelSpacing | 1.3.6.1.4.1.637.54.1.10.3.1.1.1.12 | OpticsIMChannelSpacing | RW | |
column · OpticsIMChannelSpacing · read-write · current This object specifies the channel spacing value. This value is expressed in MHZ. Consistency checks are need on this object to change the adaptiveModulationMode value. | ||||
| CradioPDHTTPBidCapabilitiesId | 1.3.6.1.4.1.637.54.1.10.3.1.1.1.13 | Integer32 | RW | |
column · Integer32 · read-write · current This object defines the identifier of the capacity, modulation and channel spacing values requested by the managing system. This identifier must be included in one of the entries of the opticsIMAllowedCapabilitiesTable. As a side effect of setting this object, the agent must set the radioPDHTTPBidCapacity, radioPDHTTPBidModulation and radioPDHTTPBidChannelSpacing objects with the value associated to this identifier. | ||||
| CradioPDHTTPBidAvailableBandwidth | 1.3.6.1.4.1.637.54.1.10.3.1.1.1.14 | Integer32 (1..2147483647) | RO | |
column · Integer32 (1..2147483647) · read-only · current This value indicates the total amount of bandwidth available on this interface and is specified in kilobits per second (Kbps). This value is calculated as the difference between the amount of bandwidth currently in use and that specified in radioPDHTTPBidCapacity object (converted in Kbps). When this value cannot be measured, this value should contain the nominal bandwidth. | ||||
| CradioPDHTTPBidOption | 1.3.6.1.4.1.637.54.1.10.3.1.1.1.15 | DisplayString | RW | |
column · DisplayString · read-write · current This object contains the option associated to the modem profile configured on this row. It refers to the radioPDHTTPBidModulation object both in preset-mode and in adaptive mode (in this case the radioPDHTTPBidModulation contains the reference modulation). | ||||
| CradioPDHTTPBidUserLabel | 1.3.6.1.4.1.637.54.1.10.3.1.1.1.16 | OpticsIMUserLabel | RW | |
column · OpticsIMUserLabel · read-write · current A textual string containing User Label of Radio Interface. | ||||
| CradioPDHTTPBidNetBandwidth | 1.3.6.1.4.1.637.54.1.10.3.1.1.1.17 | Integer32 (1..2147483647) | RO | |
column · Integer32 (1..2147483647) · read-only · current This value indicates the total amount of maximum bandwidth available on this interface and is specified in kilobits per second (Kbps). | ||||
| CradioPDHTTPBidInterfaceType | 1.3.6.1.4.1.637.54.1.10.3.1.1.1.18 | INTEGER | RO | |
column · INTEGER · read-only · current This value indicates the radio physical interface type. The mapping between this value and the associated radio equipment type will be defined in each product external specification. | ||||
| CradioPDHTTPBidClientType | 1.3.6.1.4.1.637.54.1.10.3.1.1.1.19 | INTEGER | RW | |
column · INTEGER · read-write · current It is used to determine the transmission direction of the frames received from the Radio Port. - ETS (1) the frame will be sent to ETS Layer. - ETB (2) the frame will be sent to Ethernet Switch Layer. - LINKAGG (3) the frame will be sent to Link Aggregation Layer.
| ||||
| CradioPDHTTPBidXpicImplemented | 1.3.6.1.4.1.637.54.1.10.3.1.1.1.20 | TruthValue | RO | |
column · TruthValue · read-only · current This object specifies whether the XPIC capability is present or not on this radio interface. The true value indicates that the XPIC capability is present and the false value that the capability is not present. | ||||
| CradioPDHTTPBidXpicMode | 1.3.6.1.4.1.637.54.1.10.3.1.1.1.21 | INTEGER | RW | |
column · INTEGER · read-write · current This object specifies whether the XPIC function is currently allowed to work or not.
The horizontal-polar (2) value indicates that the XPIC function is allowed to work on this interface in horizontal (H) polarization.
The vertical-polar (3) value indicates that the XPIC function is allowed to work on this interface in vertical (V) polarization.
The disabled (1) value that the function is not allowed to work.
This object is significant only if XPIC function is implemented.
In case the XPIC function is not implemented
(radioPDHTTPBidXpicImplemented = 'false' value) this object has
to contain 'disabled' value.
| ||||
| CradioPDHTTPBidXpicAssociatedInterface | 1.3.6.1.4.1.637.54.1.10.3.1.1.1.22 | InterfaceIndexOrZero | RW | |
column · InterfaceIndexOrZero · read-write · current This object specifies the radio interface (protected or not) associated to this entry in XPIC function.
It has to be provided by managing system ('0' as default value).
When not '0' the value provided has to refer to an ifIndex (index) of an existing entry on opticsIMRadioPDHTTPBidTable.
In case the XPIC function is not implemented (radioPDHTTPBidXpicImplemented = 'false' value) for this entry,
this object has to contain '0' value. | ||||
| CradioPDHTTPBidOperativeAvailableBandwidth | 1.3.6.1.4.1.637.54.1.10.3.1.1.1.23 | Integer32 (1..2147483647) | RO | |
column · Integer32 (1..2147483647) · read-only · current This value indicates the total amount of maximum and real bandwidth available on this interface and is specified in kilobits per second (Kbps). This value is calculated taking in account the actual radio interface availability. | ||||
| CradioPDHTTPBidEthCompressionMode | 1.3.6.1.4.1.637.54.1.10.3.1.1.1.24 | INTEGER | RW | |
column · INTEGER · read-write · current This value indicates if the header of the ethernet frames has to be compressed (enabled) or not (disabled) in this radio interface.
| ||||
| CradioPDHTTPBidSquelchCombiner | 1.3.6.1.4.1.637.54.1.10.3.1.1.1.25 | INTEGER | RW | |
column · INTEGER · read-write · current This object allows to the managers to squelch the local Main or Diversity receivers .
The disabled value means both Main and Diversity signals are not squelched.
The Main value means only the Main signal is squelched.
The Diversity value means only the Diversity signal is squelched.
When a local transmitter is squelched an Abnormal Condition indication is generated.
| ||||
| CradioPDHTTPBidSquelchReused | 1.3.6.1.4.1.637.54.1.10.3.1.1.1.26 | INTEGER | RW | |
column · INTEGER · read-write · current This object allows to the managers to squelch the local XPIC receiver . The off value means the XPIC signal is not squelched. he on value means the Diversity signal is squelched. When a local transmitter is squelched an Abnormal Condition indication is generated.
| ||||
| CradioPDHTTPBidEncryptionMode | 1.3.6.1.4.1.637.54.1.10.3.1.1.1.27 | INTEGER | RW | |
column · INTEGER · read-write · current This object specifies if the data on this radio interface have to be sent in encrypted (enabled value) or in a clear-text mode (disabled value).
| ||||
| CradioPDHTTPBidEncryptionPassPhrase | 1.3.6.1.4.1.637.54.1.10.3.1.1.1.28 | DisplayString | RW | |
column · DisplayString · read-write · current This object contains the pass Phrase to use for the encryption on this radio interface (on 'radio interface basis') when the encryption is enabled. This value could be overwritten by the agent using the pass Phrase on 'NE basis' when a set on the opticsIMRadioEncryptionPassPhrase is received on NE. | ||||
| CradioPDHTTPBid1588TCStatus | 1.3.6.1.4.1.637.54.1.10.3.1.1.1.29 | INTEGER | RO | |
column · INTEGER · read-only · current This object contains the status of the 1588 Transparent Clock management related the this radio interface entry. The Transparent Clock is activated on 'NE basis' but each radio interface could be in a different status. The 'notApplicable' value is returned when the radio interface doesn't support the management of the 1588 TC. The 'active' value is returned when the radio interface is supporting the 1588 TC and the feature is actualy working on. The 'notActive' value is returned when the radio interface is supporting the 1588 TC but the feature is not working due to some temporary conditions.
| ||||
| CradioPDHTTPBidCarrierMode | 1.3.6.1.4.1.637.54.1.10.3.1.1.1.30 | INTEGER | RO | |
column · INTEGER · read-only · current This object contains the mode the radio carrier (or radio channel) identified by this ifIndex is aggregated with the radio carrier belonging
to the same radio equipment (hw element).
'singleCarrier' when the radio channel/carrier is the only channel/carrier on the radio equipment;
'dualCarrierOneDirection' when this carrier is aggregated for traffic transport with the associated carrier on the same radio equipment
(towards the same direction);
'dualCarrierTwoDirections' when this carrier is not aggregated with the associated carrier on the same radio equipment; the carrier on the
same radio equipment are independent;
'notApplicable' in all the other cases (ex. radio LAG).
| ||||
| CradioPDHTTPBidMaxBandwidthForLicense | 1.3.6.1.4.1.637.54.1.10.3.1.1.1.31 | Integer32 (1..2147483647) | RW | |
column · Integer32 (1..2147483647) · read-write · current This object contains the Max Capacity (bandwidth )limited by the elementary License selected for this single or aggregated carrier. It is specified in kilobits per second (Kbps). . | ||||
| CradioPDHTTPBidXpicAutomuteEnable | 1.3.6.1.4.1.637.54.1.10.3.1.1.1.32 | TruthValue | RO | |
column · TruthValue · read-only · current This object contains the status of XPIC Automute function. | ||||
| CradioPDHTTPBidPowerSavingOperStatus | 1.3.6.1.4.1.637.54.1.10.3.1.1.1.33 | INTEGER | RO | |
column · INTEGER · read-only · current This object reports to a managing system the status of power saving process on this interface. The active (1) value means a power saving command is working as requested.
| ||||
| CradioPDHTTPBidPowerSavingTxMuteCommand | 1.3.6.1.4.1.637.54.1.10.3.1.1.1.34 | INTEGER | RW | |
column · INTEGER · read-write · current This object allows a managing system to require a tx mute of this interface for power saving purpose.
| ||||
| CradioPDHTTPBidPowerSavingCarrierDisabledCommand | 1.3.6.1.4.1.637.54.1.10.3.1.1.1.35 | INTEGER | RW | |
column · INTEGER · read-write · current This object allows a managing system to require the disabling of this interface for power saving purpose.
| ||||
| CradioPDHTTPBidPowerSavingTxMuteTimeoutPeriod | 1.3.6.1.4.1.637.54.1.10.3.1.1.1.36 | Integer32 (0..5760) | RW | |
column · Integer32 (0..5760) · read-write · current This object indicates the max time period, measured in units of minutes, from the Power Saving Tx Mute command request (radioPDHTTPBidPowerSavingTxMuteCommand to 'on' value) during which the command could be active. After the timeout expiration the agent will remove the Power Saving Tx Mute command (radioPDHTTPBidPowerSavingTxMuteCommand to 'off' value). | ||||
| CradioPDHTTPBidPowerSavingCarrierDisabledTimeoutPeriod | 1.3.6.1.4.1.637.54.1.10.3.1.1.1.37 | Integer32 (0..5760) | RW | |
column · Integer32 (0..5760) · read-write · current This object indicates the max time period, measured in units of minutes, from the Power Saving Carrier Disabled command request (radioPDHTTPBidPowerSavingCarrierDisabledCommand to 'enable' value) during which the command could be active. After the timeout expiration the agent will remove the Power Saving Carrier Disabled command (radioPDHTTPBidPowerSavingCarrierDisabledCommand to 'disable' value). | ||||
| CradioPDHTTPBidCombinerImplemented | 1.3.6.1.4.1.637.54.1.10.3.1.1.1.38 | TruthValue | RO | |
column · TruthValue · read-only · current This object specifies whether the Combiner capability is present or not on this radio equipment. The true value indicates that the Combiner capability is present and the false value that the capability is not present. | ||||
| CradioPDHTTPBidCombinerFunction | 1.3.6.1.4.1.637.54.1.10.3.1.1.1.39 | INTEGER | RW | |
column · INTEGER · read-write · current This object specifies whether the Combiner function is currently allowed to work or no on this radio equipment.
| ||||
| TopticsIMAllowedModulationTable | 1.3.6.1.4.1.637.54.1.10.3.1.2 | NA | ||
table · not-accessible · current This table contains all the modulation values allowed for each radio interface type | ||||
| RopticsIMAllowedModulationEntry | 1.3.6.1.4.1.637.54.1.10.3.1.2.1 | NA | ||
row · not-accessible · current An entry of the radioAllowedModulationTable table. Each entry (row) corresponds to a modulation value allowed on a specific radio interface type. | ||||
| CallowedModulationRadioTypeId | 1.3.6.1.4.1.637.54.1.10.3.1.2.1.1 | Integer32 | NA | |
column · Integer32 · not-accessible · current This object contains the identifier associated to a radio interface type. It identifies a index of the table. The value for each radio interface type is product dependent and defined in each product specification. | ||||
| CallowedModulationId | 1.3.6.1.4.1.637.54.1.10.3.1.2.1.2 | Integer32 | NA | |
column · Integer32 · not-accessible · current This object contains the identifier associated to a modulation value. It identifies a index of the table. | ||||
| CallowedModulation | 1.3.6.1.4.1.637.54.1.10.3.1.2.1.3 | OpticsIMModulationType | RO | |
column · OpticsIMModulationType · read-only · current This object contains an allowed modulation value for a radio interface type. | ||||
| TopticsIMAllowedCapacityTable | 1.3.6.1.4.1.637.54.1.10.3.1.3 | NA | ||
table · not-accessible · current This table contains all the radio capacities values allowed for each radio interface type | ||||
| RopticsIMAllowedCapacityEntry | 1.3.6.1.4.1.637.54.1.10.3.1.3.1 | NA | ||
row · not-accessible · current An entry of the radioAllowedCapacityTable table. Each entry (row) corresponds to a radio capacity value allowed on a specific radio interface type. | ||||
| CallowedCapacityRadioTypeId | 1.3.6.1.4.1.637.54.1.10.3.1.3.1.1 | Integer32 | NA | |
column · Integer32 · not-accessible · current This object contains the identifier associated to a radio interface type. It identifies a index of the table. The value for each radio interface type is product dependent and defined in each product specification. | ||||
| CallowedCapacityId | 1.3.6.1.4.1.637.54.1.10.3.1.3.1.2 | Integer32 | NA | |
column · Integer32 · not-accessible · current This object contains the identifier associated to a capacity value. It identifies a index of the table. | ||||
| CallowedCapacity | 1.3.6.1.4.1.637.54.1.10.3.1.3.1.3 | DisplayString | RO | |
column · DisplayString · read-only · current This object contains an allowed capacity value for a radio interface type. | ||||
| TopticsIMAllowedChannelSpacingTable | 1.3.6.1.4.1.637.54.1.10.3.1.4 | NA | ||
table · not-accessible · current This table contains all the channel spacing values allowed for each radio interface type | ||||
| RopticsIMAllowedChannelSpacingEntry | 1.3.6.1.4.1.637.54.1.10.3.1.4.1 | NA | ||
row · not-accessible · current An entry of the radioAllowedChannelSpacingTable table. Each entry (row) corresponds to a channel spacing value allowed on a specific radio interface type. | ||||
| CallowedChannelSpacingRadioTypeId | 1.3.6.1.4.1.637.54.1.10.3.1.4.1.1 | Integer32 | NA | |
column · Integer32 · not-accessible · current This object contains the identifier associated to a radio interface type. It identifies a index of the table. The value for each radio interface type is product dependent and defined in each product specification. | ||||
| CallowedChannelSpacingId | 1.3.6.1.4.1.637.54.1.10.3.1.4.1.2 | Integer32 | NA | |
column · Integer32 · not-accessible · current This object contains the identifier associated to a channel spacing value. It identifies a index of the table. | ||||
| CallowedChannelSpacing | 1.3.6.1.4.1.637.54.1.10.3.1.4.1.3 | OpticsIMChannelSpacing | RO | |
column · OpticsIMChannelSpacing · read-only · current This object contains an allowed channel spacing value for a radio interface type. | ||||
| TopticsIMRadioFrameTable | 1.3.6.1.4.1.637.54.1.10.3.1.5 | NA | ||
table · not-accessible · current This table represents the list of all cross-connectable objects on a radio frame associated to a radio direction or a radio channel. For each radio direction or radio channel the number of entries is product dependent and it will be defined in the external specification. | ||||
| RopticsIMRadioFrameEntry | 1.3.6.1.4.1.637.54.1.10.3.1.5.1 | NA | ||
row · not-accessible · current An entry of the radioFrameTable table. Each entry corresponds to a specific addressable object on a radio frame associated to a radio direction or to a radio channel. | ||||
| CradioFramePositionsIndex | 1.3.6.1.4.1.637.54.1.10.3.1.5.1.1 | Integer32 | NA | |
column · Integer32 · not-accessible · current This object contains the identifier (position) of a cross-connettable object on a radio frame. It identifies the index of the table. | ||||
| CradioFrameCrossConnectIdentifier | 1.3.6.1.4.1.637.54.1.10.3.1.5.1.2 | Integer32 (0..2147483647) | RO | |
column · Integer32 (0..2147483647) · read-only · current This object allows to identify the cross-connection in which the addressable object on radio frame is involved. It is automatically set by the agent when the radio port is cross-connected. Its value is the one that identify the cross-connection index (opticsIMCrossConnectIndex object of the opticsIMCrossConnectTable). The value of the connection identifier is the same for all the objects making part of the same cross- connection. The value '0' indicates that the addressable object on radio frame is not involved in any cross-connection. | ||||
| TopticsIMAllowedCapabilitiesTable | 1.3.6.1.4.1.637.54.1.10.3.1.6 | NA | ||
table · not-accessible · current This table contains all the channel spacing values allowed for each radio interface type | ||||
| RopticsIMAllowedCapabilitiesEntry | 1.3.6.1.4.1.637.54.1.10.3.1.6.1 | NA | ||
row · not-accessible · current An entry of the radioAllowedCapabilitiesTable table. Each entry (row) corresponds to a capacity, modulation and channel spacing values allowed on a specific radio interface type. | ||||
| CallowedCapabilitiesRadioTypeId | 1.3.6.1.4.1.637.54.1.10.3.1.6.1.1 | Integer32 | NA | |
column · Integer32 · not-accessible · current This object contains the identifier associated to a radio interface type. It identifies a index of the table. The value for each radio interface type is product dependent and defined in each product specification. | ||||
| CallowedCapabilitiesId | 1.3.6.1.4.1.637.54.1.10.3.1.6.1.2 | Integer32 | NA | |
column · Integer32 · not-accessible · current This object contains the identifier associated to the capacity, modulation and channel spacing values. It identifies a index of the table. | ||||
| CopticsIMallowedCapacity | 1.3.6.1.4.1.637.54.1.10.3.1.6.1.3 | DisplayString | RO | |
column · DisplayString · read-only · current This object contains an allowed capacity value for a radio interface type. | ||||
| CopticsIMallowedModulation | 1.3.6.1.4.1.637.54.1.10.3.1.6.1.4 | OpticsIMModulationType | RO | |
column · OpticsIMModulationType · read-only · current This object contains an allowed modulation value for a radio interface type. | ||||
| CopticsIMallowedChannelSpacing | 1.3.6.1.4.1.637.54.1.10.3.1.6.1.5 | OpticsIMChannelSpacing | RO | |
column · OpticsIMChannelSpacing · read-only · current This object contains an allowed channel spacing value for a radio interface type. | ||||
| CopticsIMallowedOption | 1.3.6.1.4.1.637.54.1.10.3.1.6.1.6 | DisplayString | RO | |
column · DisplayString · read-only · current This object contains the option associated to the modem profile identified by this row. | ||||
| CopticsIMallowedMinLicense | 1.3.6.1.4.1.637.54.1.10.3.1.6.1.7 | DisplayString | RO | |
column · DisplayString · read-only · current This object contains the value of the minimum License required to be able to select the modem profile identified by this row. | ||||
| SopticsIMAdaptiveModulationImplemented | 1.3.6.1.4.1.637.54.1.10.3.1.7 | TruthValue | RO | |
scalar · TruthValue · read-only · current This object specifies whether the Adaptive Modulatin capability is present or not. The true value indicates that the Adaptive Modulatin capability is present and the false value that the capability is not present. | ||||
| TopticsIMAdaptiveModulationTable | 1.3.6.1.4.1.637.54.1.10.3.1.8 | NA | ||
table · not-accessible · current This table contains the information related to the management of Adaptive Modulation process
(adaptiveModulationMode 'true') respect to the static configuration of modulation (preset-mode,
adaptiveModulationMode 'false') using opticsIMRadioPDHTTPBidEntry.
When the adaptiveModulationMode object is set to 'true' value then the system will adjust adaptively
the modulation and/or the channel coding format as well as a range of the other system parameters
(like i.e. transmission power level) based on the near-instantaneous channel quality information
perceived by the receiver and some user's parameter.
The parameters related to the transmission power level management in case of adaptiveModulationMode 'true'
are contained in the opticsIMAdaptiveModulationRadioTxPowerEntry. | ||||
| RopticsIMAdaptiveModulationEntry | 1.3.6.1.4.1.637.54.1.10.3.1.8.1 | NA | ||
row · not-accessible · current An entry of the radioAdaptiveModulationTable table. Each entry corresponds to a Radio Physical Interface.
| ||||
| CadaptiveModulationMode | 1.3.6.1.4.1.637.54.1.10.3.1.8.1.1 | TruthValue | RW | |
column · TruthValue · read-write · current This object specifies whether the Adaptive Modulation is currently allowed to work or not. The 'true' value indicates that the Adaptive Modulation process is allowed to work and the 'false' value that the process is not allowed to work (modulation value has a fixed value). This object is significant only if Adaptive Modulation proces is implemented. | ||||
| CadaptiveModulationSchemeRangeId | 1.3.6.1.4.1.637.54.1.10.3.1.8.1.2 | INTEGER | RW | |
column · INTEGER · read-write · current This object defines the identifier (requested by the managing system) of the list of modulation schemes whithin the Adaptive Modulation process is allowed to work. This identifier must be included in one of the entries of the opticsIMAdaptiveAllowedCapabilitiesTable (adaptiveAllowedSchemeRangeId). As a side effect of setting this object: - the agent must set the adaptiveModulationSchemeRange object with a string containing all the modulation values associated to this identifier, - the agent must create (or destroy) the related entries on opticsIMAdaptiveModulationSwitchThresholdsTable and opticsIMAdaptiveModulationRadioTxPowerTable for each modulation value included in the range. | ||||
| CadaptiveModulationSchemeRange | 1.3.6.1.4.1.637.54.1.10.3.1.8.1.3 | DisplayString | RO | |
column · DisplayString · read-only · current This object specifies the list of modulation values in the scheme range selected. | ||||
| CadaptiveModulationReferenceModulationId | 1.3.6.1.4.1.637.54.1.10.3.1.8.1.4 | INTEGER | RW | |
column · INTEGER · read-write · current This object defines the identifier (requested by the managing system) of one of modulation scheme whithin the list of modulation schemes (adaptiveModulationSchemeRange). This identifier must be included in one of the entries of the opticsIMAdaptiveAllowedCapabilitiesTable (adaptiveAllowedModulationId for a specific adaptiveModulationSchemeRangeId). As a side effect of setting this object, the agent must set to the adaptiveModulationReferenceModulation object with the value (adaptiveAllowedModulation) associated to this identifier and to adaptiveModulationSchemeRangeId. | ||||
| CadaptiveModulationReferenceModulation | 1.3.6.1.4.1.637.54.1.10.3.1.8.1.5 | OpticsIMModulationType | RW | |
column · OpticsIMModulationType · read-write · current This object defines the reference modulation scheme. It's is used as a reference value to guarantee all the system performances (transmission power level mask). | ||||
| CadaptiveModulationWaitToSwitchTime | 1.3.6.1.4.1.637.54.1.10.3.1.8.1.6 | INTEGER (0..20) | RW | |
column · INTEGER (0..20) · read-write · current This object specifies the time to wait before to switch to an upper modulation scheme value. It is an integer with associated measure unit expressed in decade of sec. (e.g. 15 means 1.5 sec | ||||
| CadaptiveModulationManualOperation | 1.3.6.1.4.1.637.54.1.10.3.1.8.1.7 | INTEGER | RW | |
column · INTEGER · read-write · current This object is used to initiate (active) or terminate (notActive) a manual handling of modulation when the Adaptive Modulation process is active, without to return to static modulation Mode (preset-mode), starting from current modulation value and including the transmission power limits, . It's the same that to freeze the Adaptive modulation state without other modulation switching. In this state will be possible to change the current Modulation (adaptiveModulationCurrentModulationId object) When a manual handling of modulation on Adaptive mode is initiated an Abnormal Condition indication is generated. When it is terminated the Abnormal Condition indication is removed. When the Active value is is selected, the adaptiveModulationCurrentModulationId object is updated with the identifier of the current modulation.
| ||||
| CadaptiveModulationCurrentModulationId | 1.3.6.1.4.1.637.54.1.10.3.1.8.1.8 | INTEGER | RW | |
column · INTEGER · read-write · current A SET request on this object is allowed only when the adaptiveModulationManualOperation is set to 'active' value. This object specifies the modulation value when a manual operation on modulation value on Adaptive mode is active (adaptiveModulationManualOperation set to 'active' value). It defines the identifier (requested by the managing system) of one of modulation scheme whithin the list of modulation schemes (adaptiveModulationSchemeRange) used by Adaptive process. This identifier must be included in one of the entries of the opticsIMAdaptiveAllowedCapabilitiesTable (adaptiveAllowedModulationId for a specific adaptiveModulationSchemeRangeId). The request is accepted only if the new value is a increment (+1) or a decrement (-1) of the old one. As a side effect of setting this object, the agent must set to the adaptiveModulationCurrentModulation object with the value (adaptiveAllowedModulation) associated to this identifier and to adaptiveModulationSchemeRangeId. | ||||
| CadaptiveModulationCurrentModulation | 1.3.6.1.4.1.637.54.1.10.3.1.8.1.9 | OpticsIMModulationType | RO | |
column · OpticsIMModulationType · read-only · current This object contains the modulation value currently used by the system and computed by the
Adaptive Modulation process.
It's updated on the GET_SNMP request from the managing system when no manual operation is active
('notActive' value on adaptiveModulationManualOperation) or by the SET_SNMP request on
adaptiveModulationCurrentModulationId when a manual operation is active
('active' value on adaptiveModulationManualOperation ). | ||||
| CadaptiveModulationCurrentCapacity | 1.3.6.1.4.1.637.54.1.10.3.1.8.1.10 | DisplayString | RO | |
column · DisplayString · read-only · current This object contains the capacity value currently computed by the Adaptive Modulation process. It's updated on the GET_SNMP request from the managing system. | ||||
| CadaptiveModulationDrivingMSE | 1.3.6.1.4.1.637.54.1.10.3.1.8.1.11 | INTEGER | RW | |
column · INTEGER · read-write · current This object is used to indicate in case of 1+1HSB radio configurations which MSE (Mean Square Error) of the two remote receivers has to be used in the Adaptive algorithm. In all the other configurations this parameter is not significant and has to be set to 'notRelevant' value.
| ||||
| CadaptiveModulationCapabilitiesId | 1.3.6.1.4.1.637.54.1.10.3.1.8.1.12 | Integer32 | RW | |
column · Integer32 · read-write · current This object defines the identifier of the modem profile in Adaptive mode requested by managing system. The modem profile is identified by channel spacing, reference modulation and option values. This identifier must be included in one of the entries of the opticsIMAdaptiveEnhAllowedCapabilitiesTable (adaptiveEnhAllowedCapabilitiesId). As a side effect of setting this object, the agent must set the radioPDHTTPBidChannelSpacing, radioPDHTTPBidModulation and radioPDHTTPBidOption objects in RadioPDHTTPBidTable with the value associated to this identifier. | ||||
| CadaptiveModulationSupported | 1.3.6.1.4.1.637.54.1.10.3.1.8.1.13 | Bits | RW | |
column · Bits · read-write · current A value that uniquely identifies the set of modulation schemes selected to be used in Adaptive mode with the modem profile identified by adaptiveModulationCapabilitiesId. Modulation schemes in this object that are not available in adaptiveEnhAllowedModulationTable for the adaptiveModulationCapabilitiesId cannot be enabled.
| ||||
| CadaptiveModulationSwitchThresholdOffset | 1.3.6.1.4.1.637.54.1.10.3.1.8.1.14 | Integer32 (-2..4) | RW | |
column · Integer32 (-2..4) · read-write · current This object contains a value used to change the threshold to switch from a modulation value to an other modulation value. The value is defined around a threshold base value (considered the best for this switch). The value '0' means that the threshold base value has to be used. The value '0' is the default value for this object. The threshold base value (for each possible switch) is product dependent. This value is defined at Radio interface base and not at modulation value base. | ||||
| TopticsIMAdaptiveModulationSwitchThresholdsTable | 1.3.6.1.4.1.637.54.1.10.3.1.9 | NA | ||
table · not-accessible · current This table contains the informations about the threshoulds, provided by managing systems, to switch between each couple of modulation schemes allowed to switch. | ||||
| RopticsIMAdaptiveModulationSwitchThresholdsEntry | 1.3.6.1.4.1.637.54.1.10.3.1.9.1 | NA | ||
row · not-accessible · current An entry of the opticsIMAdaptiveModulationSwitchThresholdsTable table. Each entry corresponds to a couple of modulation values allowed to switch from one to the other. Each entry is created or as a side effect of setting of adaptiveModulationSchemeRangeId object for each couple of modulation value included in the range or at system start-up with default entries (all modulation value allowed). | ||||
| CadaptiveModulationFromToModulationOne | 1.3.6.1.4.1.637.54.1.10.3.1.9.1.1 | OpticsIMModulationType | NA | |
column · OpticsIMModulationType · not-accessible · current The first of the two modulation values involved in the desiderated switch. | ||||
| CadaptiveModulationFromToModulationTwo | 1.3.6.1.4.1.637.54.1.10.3.1.9.1.2 | OpticsIMModulationType | NA | |
column · OpticsIMModulationType · not-accessible · current The second of the two modulation values involved in the desiderated switch. | ||||
| CadaptiveModulationSwitchThresholdVariation | 1.3.6.1.4.1.637.54.1.10.3.1.9.1.3 | Integer32 (-2..4) | RW | |
column · Integer32 (-2..4) · read-write · current This object contains a value used to change the threshold to switch between adaptiveModulationFromToModulationOne and adaptiveModulationFromToModulationTwo around a threshold base value (considered the best for this switch). The value '0' means that the threshold base value has to be used. The value '0' is the default value for this object. The threshold base value (for each possible switch) is product dependent. | ||||
| TopticsIMAdaptiveAllowedChannelSpacingTable | 1.3.6.1.4.1.637.54.1.10.3.1.10 | NA | ||
table · not-accessible · current This table contains all the channel spacing values allowed for each radio interface type in case the Adaptive Modulation process is allowed to work (adaptiveModulationMode 'true') | ||||
| RopticsIMAdaptiveAllowedChannelSpacingEntry | 1.3.6.1.4.1.637.54.1.10.3.1.10.1 | NA | ||
row · not-accessible · current An entry of the radioAllowedChannelSpacingTable table. Each entry (row) corresponds to a channel spacing value allowed on a specific radio interface type. | ||||
| CadaptiveAllowedChannelSpacingRadioTypeId | 1.3.6.1.4.1.637.54.1.10.3.1.10.1.1 | Integer32 | NA | |
column · Integer32 · not-accessible · current This object contains the identifier associated to a radio interface type. It identifies a index of the table. The value for each radio interface type is product dependent and defined in each product specification. | ||||
| CadaptiveAllowedChannelSpacingId | 1.3.6.1.4.1.637.54.1.10.3.1.10.1.2 | Integer32 | NA | |
column · Integer32 · not-accessible · current This object contains the identifier associated to a channel spacing value. It identifies a index of the table. | ||||
| CadaptiveAllowedChannelSpacing | 1.3.6.1.4.1.637.54.1.10.3.1.10.1.3 | OpticsIMChannelSpacing | RO | |
column · OpticsIMChannelSpacing · read-only · current This object contains an allowed channel spacing value for a radio interface type in case the Adaptive Modulation process is allowed to work (adaptiveModuationMode 'true'). | ||||
| TopticsIMAdaptiveAllowedCapabilitiesTable | 1.3.6.1.4.1.637.54.1.10.3.1.11 | NA | ||
table · not-accessible · current This table contains all the capabilities allowed in the system for Adaptive Modulation process.
These system capabilities (identified by adaptiveAllowedCapabilitiesIndex specific for, i.e.,
for each radio interface type) are described in term of lists of modulation values whithin
the Adaptive Modulation process is allowed to work.
Each list (SchemeRange) is identified by adaptiveAllowedSchemeRangeId index and composed by
adaptiveAllowedModulation values identified by the adaptiveAllowedModulationId indexes. | ||||
| RopticsIMAdaptiveAllowedCapabilitiesEntry | 1.3.6.1.4.1.637.54.1.10.3.1.11.1 | NA | ||
row · not-accessible · current An entry of the opticsIMAdaptiveAllowedCapabilitiesTable table. Each entry corresponds to a modulation value belonging to a scheme range allowed on the system for each specific capability index (i.e. radio interface type). | ||||
| CadaptiveAllowedCapabilitiesIndex | 1.3.6.1.4.1.637.54.1.10.3.1.11.1.1 | Integer32 | NA | |
column · Integer32 · not-accessible · current This object contains the identifier associated to a capability type (i.e. radio interface type). It identifies a index of the table. The value for each capability type is product dependent and defined in each product specification. | ||||
| CadaptiveAllowedSchemeRangeId | 1.3.6.1.4.1.637.54.1.10.3.1.11.1.2 | Integer32 | NA | |
column · Integer32 · not-accessible · current This object contains the identifier associated to a scheme range allowed. It identifies a index of the table. | ||||
| CadaptiveAllowedModulationId | 1.3.6.1.4.1.637.54.1.10.3.1.11.1.3 | Integer32 | NA | |
column · Integer32 · not-accessible · current This object contains the identifier associated to a modulation value belonging to the scheme range identified by adaptiveAllowedSchemeRangeId. It identifies a index of the table. | ||||
| CadaptiveAllowedModulation | 1.3.6.1.4.1.637.54.1.10.3.1.11.1.4 | OpticsIMModulationType | RO | |
column · OpticsIMModulationType · read-only · current This object contains an allowed modulation value belonging to the scheme range identified by adaptiveAllowedSchemeRangeId. | ||||
| CadaptiveAllowedCapacity | 1.3.6.1.4.1.637.54.1.10.3.1.11.1.5 | DisplayString | RO | |
column · DisplayString · read-only · current This object contains the allowed capacity value associated to the modulation value for this modem profile (identified by adaptiveEnhAllowedCapabilitiesId). | ||||
| CadaptiveAllowedMinLicense | 1.3.6.1.4.1.637.54.1.10.3.1.11.1.6 | DisplayString | RO | |
column · DisplayString · read-only · current This object contains the value of the minimum License required to be able to select the modem profile identified by this row. | ||||
| TopticsIMAdaptiveAvailableBandwidthTable | 1.3.6.1.4.1.637.54.1.10.3.1.12 | NA | ||
table · not-accessible · current This table contains the bandwidth available and the capacity for each modulation scheme value when the Adaptive Modulation process is allowed to work (adaptiveModulationMode set to 'true' value). | ||||
| RopticsIMAdaptiveAvailableBandwidthEntry | 1.3.6.1.4.1.637.54.1.10.3.1.12.1 | NA | ||
row · not-accessible · current An entry of the radioAdaptiveAvailableBandwidthTable table. Each entry corresponds to a Radio Plesiochronous Physical Interface (RPPI) and to a modulation scheme value supported. | ||||
| CadaptiveModulationType | 1.3.6.1.4.1.637.54.1.10.3.1.12.1.1 | OpticsIMModulationType | NA | |
column · OpticsIMModulationType · not-accessible · current This object specifies the type of modulation. | ||||
| CadaptiveAvailableBandwidth | 1.3.6.1.4.1.637.54.1.10.3.1.12.1.2 | Integer32 (1..2147483647) | RO | |
column · Integer32 (1..2147483647) · read-only · current This value is significant only when the adaptive modulation process is working (adaptiveModulationMode set to 'true' value). This value indicates the total amount of bandwidth available on this interface for the modulation scheme value specified in radioAdaptiveModulation. It is specified in kilobits per second (Kbps). This value is calculated as the difference between the amount of bandwidth currently in use for a modulation value and that specified for radioAdaptiveModulation once defined radioPDHTTPBidChannelSpacing object (converted in Kbps). When this value cannot be measured, this value should contain the nominal bandwidth. | ||||
| CadaptiveCapacity | 1.3.6.1.4.1.637.54.1.10.3.1.12.1.3 | DisplayString | RO | |
column · DisplayString · read-only · current This object contains the capacity value associated to the modulation value. | ||||
| CadaptiveNetBandwidth | 1.3.6.1.4.1.637.54.1.10.3.1.12.1.4 | Integer32 (1..2147483647) | RO | |
column · Integer32 (1..2147483647) · read-only · current This value indicates the total amount of maximum bandwidth available for this modulation value and is specified in kilobits per second (Kbps). | ||||
| TopticsIMAdaptiveEnhAllowedCapabilitiesTable | 1.3.6.1.4.1.637.54.1.10.3.1.13 | NA | ||
table · not-accessible · current This table contains all the allowed modem profiles in Adaptive mode for each radio interface type | ||||
| RopticsIMAdaptiveEnhAllowedCapabilitiesEntry | 1.3.6.1.4.1.637.54.1.10.3.1.13.1 | NA | ||
row · not-accessible · current An entry of the radioAllowedCapabilitiesTable table. Each entry (row) corresponds to a channel spacing, reference modulation and option values allowed on a specific radio interface type in Adaptive mode. | ||||
| CadaptiveEnhAllowedCapabilitiesRadioTypeId | 1.3.6.1.4.1.637.54.1.10.3.1.13.1.1 | Integer32 | NA | |
column · Integer32 · not-accessible · current This object contains the identifier associated to a radio interface type. It identifies a index of the table. The value for each radio interface type is product dependent and defined in each product specification. | ||||
| CadaptiveEnhAllowedCapabilitiesId | 1.3.6.1.4.1.637.54.1.10.3.1.13.1.2 | Integer32 | NA | |
column · Integer32 · not-accessible · current This object contains the identifier associated to the capacity, modulation and channel spacing values. It identifies a index of the table. | ||||
| CadaptiveEnhAllowedChannelSpacing | 1.3.6.1.4.1.637.54.1.10.3.1.13.1.3 | OpticsIMChannelSpacing | RO | |
column · OpticsIMChannelSpacing · read-only · current This object contains an allowed channel spacing value for a radio interface type. | ||||
| CadaptiveEnhAllowedReferenceModulation | 1.3.6.1.4.1.637.54.1.10.3.1.13.1.4 | OpticsIMModulationTypeOrZero | RO | |
column · OpticsIMModulationTypeOrZero · read-only · current This object contains an allowed reference modulation value for a radio interface type. The zero value is allowed to manage any value for this object. | ||||
| CadaptiveEnhAllowedOption | 1.3.6.1.4.1.637.54.1.10.3.1.13.1.5 | DisplayString | RO | |
column · DisplayString · read-only · current This object contains the option associated to the modem profile identified by this row. | ||||
| TopticsIMAdaptiveEnhAllowedModulationTable | 1.3.6.1.4.1.637.54.1.10.3.1.14 | NA | ||
table · not-accessible · current This table contains all the modulation values (and the related capacity values) allowed
for each modem profile (identified by adaptiveEnhAllowedCapabilitiesRadioTypeId and
adaptiveEnhAllowedCapabilitiesId) allowed for Adaptive Modulation process.
These modulation values (identified by adaptiveEnhAllowedModulationId ) are the modulation values whithin
the Adaptive Modulation process is allowed to work. | ||||
| RopticsIMAdaptiveEnhAllowedModulationEntry | 1.3.6.1.4.1.637.54.1.10.3.1.14.1 | NA | ||
row · not-accessible · current An entry of the opticsIMAdaptiveEnhAllowedModulationTable table. Each entry corresponds to a modulation value allowed on the system for each modem profile (adaptiveEnhAllowedCapabilitiesId)in adaptive mode and specific for radio interface (adaptiveEnhAllowedCapabilitiesRadioTypeId). | ||||
| CadaptiveEnhAllowedModulationId | 1.3.6.1.4.1.637.54.1.10.3.1.14.1.1 | Integer32 | NA | |
column · Integer32 · not-accessible · current This object contains the identifier associated to a modulation value allowed for this modem profile (identified by adaptiveEnhAllowedCapabilitiesId). It identifies a index of the table. | ||||
| CadaptiveEnhAllowedModulation | 1.3.6.1.4.1.637.54.1.10.3.1.14.1.2 | OpticsIMModulationType | RO | |
column · OpticsIMModulationType · read-only · current This object contains an allowed modulation value for this modem profile (identified by adaptiveEnhAllowedCapabilitiesId). | ||||
| CadaptiveEnhAllowedCapacity | 1.3.6.1.4.1.637.54.1.10.3.1.14.1.3 | DisplayString | RO | |
column · DisplayString · read-only · current This object contains the allowed capacity value associated to the modulation value for this modem profile (identified by adaptiveEnhAllowedCapabilitiesId). | ||||
| CadaptiveEnhAllowedMinLicense | 1.3.6.1.4.1.637.54.1.10.3.1.14.1.4 | DisplayString | RO | |
column · DisplayString · read-only · current This object contains the value of the minimum License required to be able to select the modem profile identified by this row. | ||||
| CadaptiveEnhAllowedModulationSupportAsReference | 1.3.6.1.4.1.637.54.1.10.3.1.14.1.5 | TruthValue | RO | |
column · TruthValue · read-only · current This object define if the adaptiveEnhAllowedModulation can be used to configure the reference modulation ('true' value) or not ('false' value). | ||||
| SopticsIMRadioOverbooking | 1.3.6.1.4.1.637.54.1.10.3.1.15 | Unsigned32 (0..1) | RW | |
scalar · Unsigned32 (0..1) · read-write · current This attribute defines the overbooking (OB) for the Committed Bandwidth
on adaptive modulation.
When the value of 'opticsIMRadioOverbooking' is equal to 1 it means that
the 'OB for Committed BW' = 'Committed BW': the Admission control is on the Committed BW.
When the value of 'opticsIMRadioOverbooking' is equal to 0 it means unlimited
overbooking i.e. effectively CoS is set as Best Effort : the Admission control is on the Best effort BW. | ||||
| TopticsIMRadioEthCompressionTable | 1.3.6.1.4.1.637.54.1.10.3.1.16 | NA | ||
table · not-accessible · current This table contains the ethernet type values identifying the ethernet frames to compress (header compression). | ||||
| RopticsIMRadioEthCompressionEntry | 1.3.6.1.4.1.637.54.1.10.3.1.16.1 | NA | ||
row · not-accessible · current An entry of the opticsIMRadioEthCompressionTable table. Each entry corresponds to a ether type value on 'NE basis'. | ||||
| CopticsIMRadioEthTypeIndex | 1.3.6.1.4.1.637.54.1.10.3.1.16.1.1 | INTEGER | NA | |
column · INTEGER · not-accessible · current This object specifies the value or the Ethernet type of the ethernet frames to compress. | ||||
| CopticsIMRadioEthTypeValue | 1.3.6.1.4.1.637.54.1.10.3.1.16.1.2 | INTEGER | RO | |
column · INTEGER · read-only · current This object reports in an object accessible by managing system by a GET-SNMP, the value or the same Ethernet type in the opticsIMRadioEthTypeIndex index object. | ||||
| CopticsIMRadioEthRowStatus | 1.3.6.1.4.1.637.54.1.10.3.1.16.1.3 | RowStatus | RC | |
column · RowStatus · read-create · current This object is used to create a new row or to delete an existing row in the table | ||||
| SopticsIMRadioEncryptionPassPhrase | 1.3.6.1.4.1.637.54.1.10.3.1.17 | DisplayString | RW | |
scalar · DisplayString · read-write · current This object contains the pass Phrase on 'NE bais' to use for the encryption for all the radio interfaces
where the encryption is enabled.
When this object will be set to a not null value, the radioPDHTTPBidEncryptionPassPhrase for each radio direction
(on 'radio interface basis') will be update by the agent with the same value.
Once defined on 'NE basis', the managing system is allowed to define the pass Phrase on 'radio interface basis'
per specific radio directions. | ||||
| SopticsIMRadioEthernetStatsAggregateMode | 1.3.6.1.4.1.637.54.1.10.3.1.18 | INTEGER | RW | |
scalar · INTEGER · read-write · current This object defines what frames are included/excluded on ethernet counters when the ethernet statistics on the aggregate radio LAG L1 interface are requested from the manager. The default value is 'tdmAndEthernet'
| ||||
| TopticsIMAllowedCapacityLicenseTable | 1.3.6.1.4.1.637.54.1.10.3.1.19 | NA | ||
table · not-accessible · current This table contains all the radio capacities values allowed for each radio interface type | ||||
| RopticsIMAllowedCapacityLicenseEntry | 1.3.6.1.4.1.637.54.1.10.3.1.19.1 | NA | ||
row · not-accessible · current An entry of the radioAllowedCapacityLicenseTable table. Each entry (row) corresponds to a capacity license value allowed on a specific radio interface type.
| ||||
| CallowedCapacityLicenseId | 1.3.6.1.4.1.637.54.1.10.3.1.19.1.1 | Integer32 | NA | |
column · Integer32 · not-accessible · current This object contains the identifier associated to a radio interface type. It identifies a index of the table. The value for each radio interface type is product dependent and defined in each product specification. | ||||
| CallowedCapacityLicense | 1.3.6.1.4.1.637.54.1.10.3.1.19.1.2 | Integer32 (1..2147483647) | RO | |
column · Integer32 (1..2147483647) · read-only · current This object contains an allowed capacity value for a radio interface type. | ||||
| NopticsIMRadioTrsPdhMCConf | 1.3.6.1.4.1.637.54.1.10.99.3 | |||
| NopticsIMRadioTrsPdhMCCompl | 1.3.6.1.4.1.637.54.1.10.99.3.1 | |||
| MopticsIMRadioTrsPdhMc | 1.3.6.1.4.1.637.54.1.10.99.3.1.1 | |||
compliance · current This module compliance describes a set of objects required for Optics-IM Agent implementation. These objects are defined inside opticsIMRadioTrsPdhMib. | ||||
| NopticsIMRadioTrsPdhMCGroup | 1.3.6.1.4.1.637.54.1.10.99.3.2 | |||
| GopticsIMRadioPDHTTPGroup | 1.3.6.1.4.1.637.54.1.10.99.3.2.1 | |||
group · current This group describes the Radio PDH mandatory objects.
| ||||
| GopticsIMOptRadioPDHTTPGroup | 1.3.6.1.4.1.637.54.1.10.99.3.2.2 | |||
group · current This group describes the Radio PDH optional objects. | ||||
| GopticsIMAdaptiveModulationGroup | 1.3.6.1.4.1.637.54.1.10.99.3.2.3 | |||
group · current This group describes the Adaptive Modulation mandatory objects.
| ||||
Textual conventions
OpticsIMChannelSpacingINTEGEReightyMHz(18)fiftyMHz(15)fiftySixMHZ(4)fiveHundredMHZ(24)fiveMHZ(8)fortyMHZ(14)fourteenMHZ(2)oneHundredMHZ(20)oneHundredTwelveMHZ(21)oneHundredTwentyFiveMHZ(22)oneThousandFiveHundredMHZ(28)oneThousandMHZ(26)oneThousandTwoHundredFiftyMHZ(27)sevenHundredFiftyMHZ(25)sevenMHZ(1)sixtyMHz(17)sixtyTwoDotFiveMHz(19)tenMHZ(9)thirtyMHZ(13)threeDotFiftyMHZ(6)threeDotSeventyFiveMHZ(7)twentyEight-MHZ(3)twentyEightMHZ(11)twentyFiveMHZ(16)twentyMHZ(10)twentyNineDotSixtyFiveMHZ(12)twoDotFiftyMHZ(5)twoGHZ(29)twoHundredFiftyMHZ(23)This object specifies the type of modulation.
OpticsIMModulationTypeINTEGERbPsk(16)bPskOneFourth(14)bPskOneHalf(15)eightPsk(9)fiveHundredTwelveQam(10)fourQam(1)fourQamStrong(17)fourThousandNinetySixQam(13)oneHundredTwentyEightQam(8)oneHundredTwentyEightTcm(5)oneThousandTwentyFourQam(11)sixteenQam(2)sixtyFourQam(4)thirtyTwoQam(7)thirtyTwoTcm(3)twoHundredFiftySixQam(6)twoThousandFortyEightQam(12)This object specifies the type of modulation.
OpticsIMModulationTypeOrZeroINTEGERbPsk(16)bPskOneFourth(14)bPskOneHalf(15)eightPsk(9)fiveHundredTwelveQam(10)fourQam(1)fourQamStrong(17)fourThousandNinetySixQam(13)noModulationValue(100)nullValue(0)oneHundredTwentyEightQam(8)oneHundredTwentyEightTcm(5)oneThousandTwentyFourQam(11)sixteenQam(2)sixtyFourQam(4)thirtyTwoQam(7)thirtyTwoTcm(3)twoHundredFiftySixQam(6)twoThousandFortyEightQam(12)This object specifies the type of modulation. '0' value is allowed meaning 'not significant' '100' value is meaning 'no modulation value available'