MIB Browser
Optics-IM Common Textual Conventions.
Organization
Alcatel TND
Root OID
1.3.6.1.4.1.637.54.1.1.101
Last updated
Objects
1
Source
Show full MIB
snmptranslate -m OPTICSIM-COMMON-TC -Tp
snmpwalk -v2c -c <community> -m OPTICSIM-COMMON-TC <host> 1.3.6.1.4.1.637.54.1.1.101

Imports

SNMPv2-CONFMODULE-COMPLIANCE, NOTIFICATION-GROUP
SNMPv2-SMIBits, Integer32, IpAddress, MODULE-IDENTITY, MibIdentifier, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, iso
SNMPv2-TCDisplayString, PhysAddress, TEXTUAL-CONVENTION, TimeInterval, TruthValue
TSDIM-BASICREG-MIBtsdimBasicMib
TSDIM-SNMP-TCTsdimEventTimeInt

OID tree

NameOIDTypeAccessStatus
IopticsICommonTc1.3.6.1.4.1.637.54.1.1.101

Textual conventions

OpticImFileTrasferProtocolList Bits

clientFtp(1) ieee802-1e(0) serverFtp(2)

The list of the possible file transfer protocols that can be supported
and/or used by the NE.
OpticsIMEquipmentProtectionSwitchCriteria INTEGER

cLAProcedureInProgress(8) cLAfailure(9) controlPlatformFailure(6) equipmentFailure(2) equipmentMissing(3) flashCardFailure(5) flashCardRealignmentInProgress(4) noOne(1) portFailure(7)

This object contains the highest priority automatic switch request
currently active on the protection unit.
OpticsIMIpRoutingProtocol INTEGER

bbnSpflgp(12) bgp(14) ciscolgrp(11) egp(5) esis(10) ggp(6) hello(7) icmp(4) isis(9) local(2) netmgmt(3) none(1) ospf(13) ospfAndRip(15) rip(8) static(16)

This textual convention represents the IP routing protocol.
OpticsIMPmElapsedTime TimeInterval
It specifies the amount of time,
---  measured in units of 0.01 second,
     whose time granularity is NE-product specific (NE time granularity
     in units of 1 second) and independent from TimeInterval SNMP SYNTAX,
     that statistics for this entry (the current interval) have been
     counted.
OpticsIMPmFilterGranularityPeriod INTEGER

fifteenMin(1) null(0) oneHour(3) twentyFourHours(2)

It indicates the time base for measuring: 15 minutes, 24 hours or
one hour.
The null value is used as a shortcut when retrieving history data
with the filtering criteria.
OpticsIMPmGranularityPeriod INTEGER

fifteenMin(1) oneHour(3) twentyFourHours(2)

It indicates the time base for measuring: 15 minutes,24 hours or
one hour.
OpticsIMPmIndex INTEGER
It represents an index for PM entries.
OpticsIMPmLastDiscontinuityTimeStamp TsdimEventTimeInt
Reporting the time when the last counters updating discontinuity event
occurred and involved the measurement point; the events can be for
example board insertion or board reset.
Also date change is considered such a discontinuity even if counters
updating is not involved in a change.
This time is synchronized with the EC controller time.
OpticsIMPmMaxSuppressedIntervals INTEGER
The PmMaxSuppressedIntervals object limits the maximum number of
suppressed intervals that will be collected without creating an
instance of the historyData object.
For example, consider an instance of current Data associated to one
resource with maxSuppressedIntervals set to 32, and the interval set
to 15 minutes: it means that after 32 consecutive suppressed (e.g.,
all-zero) intervals (8 hours) at least one historyData record (with
all zero PM Parameters) will be generated with a NumSuppressedIntervals
equal to 32.
This ensures that at least one historyData record per
maxSuppressedIntervals will be created.
The value of this attribute cannot exceed the maximum possible value of
the numSuppressedIntervals attribute.
A value of (2^32)-1 implies infinite zero suppression, i.e. always
suppress the zero intervals.
OpticsIMPmNumSuppressedIntervals INTEGER
This attribute is non-zero only if the NE is suppressing History Data
entry creation for the measured resource when the current interval
terminates with 'all-zeroes' performance measurements.
When non-zero, this attribute represents the number of 'all-zeroes'
intervals that were suppressed immediately prior to the current interval.
This attribute gets increment at the end of an interval if suppression
has occurred, otherwise, the attribute is reset.
OpticsIMPmPeriodTime TsdimEventTimeInt
The 0 value indicates the null value.
OpticsIMPmRetrievingTime TsdimEventTimeInt
The NE time when counters are retrieved cause a maintenance action
OpticsIMPmStartTime TsdimEventTimeInt
Indicate the time when the performance monitoring point has been
activated in NE and so when relative Current Datas have been created.
OpticsIMPmSuspectIntervalFlag TruthValue
This attribute is used to indicate that the performance data for the
current period may not be reliable.
Some reasons for this to occur are:
- Suspect data were detected by the actual resource doing data collection
- Transition of the row status attribute to/from the 'inService' state.
- The performance counters were reset during the interval.
- The current Data object associated to a resource was created during the
  monitoring period.
OpticsIMPmThresholdDataInstance INTEGER
It indicates a threshold data table entry: the value of this object is
the value of the relative PM Threshold Index.
OpticsIMProtectionGroupType INTEGER

onePlusOne(1) oneToN(2)

This object specifies whether the protection scheme used is 1+1 or 1:N.
OpticsIMProtectionPriority Integer32
This object specifies the priority of the traffic carried on the resource
associated with the protected instance. Valid values for this object are
integers, where the value 1 indicates the highest priority and a larger
value indicates a lower priority.
OpticsIMProtectionSwitchCommand INTEGER

forcedSwitch(3) lockout(4) manualSwitch(2) noRequest(1)

This object specifies the operator switch command currently active (if
any)on the protection unit.
The forced and manual switch commands have to be addressed to a protected
unit if revertive mode is supported, instead can be addressed both to
protected and protecting unit in case not Revertive mode is supported.
Each request has to be checked to verify if the command can be executed,
according to the priority implicitely associated to each type of command.
In order to remove a switch or lockout command the noRequest value has
to be used.
OpticsIMProtectionSwitchStatus INTEGER

active(1) standby(2)

This object indicates the status of the protection unit: active or
standby.
OpticsIMProtectionUnitType INTEGER

main(1) spare(2)

This object specifies the type of protection unit: main or spare.
OpticsIMPtpIpInterfaceMode INTEGER

asynchronous(3) crossover(7) dce(5) dte(2) inE1orDs1Frame(4) normal(6) notUsed(1)

This textual convention represents the mode of working of the
point-to-point interface.
OpticsIMPtpIpInterfaceType INTEGER

g703(3) multitype(5) repeater(4) rf(1) v11(2)

This  textual convention represents the point-to-point port type.
OpticsIMRadioChannelNumber INTEGER

ch0(0) ch1(1) ch2(2) ch3(3) ch4(4) ch5(5) ch6(6) ch7(7) ch8(8) ch9(9) chA(21) chB(22) chC(23) chCommon(99) chD(24) chE(25) chF(26) chG(27) chH(28) chI(30) chK(29)

This object indicates the channel number associated to a radio
physical port.
OpticsIMRevertive TruthValue
This object indicates whether the protection scheme is revertive or not.
If the value is TRUE, the traffic is returned to the protected channel
that initiated the switch after the fault has cleared and the
waitToRestoteTime (if any) has exipered. If the value is FALSE, then
after the fault has cleared, traffic does not revert to the protected
channel that initiated the switch.
OpticsIMStmLevel Unsigned32
This object specifies the level, n, of the STM-n signal being
received, transmitted, or received and  transmitted.
OpticsIMSwdlStatusIndicator INTEGER

downloading(1) idle(2)

This Textual Convention defines the Status of Software Download
operation.
OpticsIMThrIndexNext2 Integer32
This object contains an appropriate value to be used for pm*ThrIndex
when creating entries in the opticsIM*ThresholdDataTable (where *=Rs/Ms/0).
The value -1 indicates that no unassigned entries are available.
To obtain the index value for a new entry, the manager issues a management
protocol retrieval operation to obtain the current value of this object.
After each retrieval, the agent should modify the value to the next
unassigned index (or -1).
OpticsIMigmpVersion INTEGER

iGMPv1(1) iGMPv2(2) iGMPv3(3)

This object specifies the IGMP Snooping mode:
IGMP v1, IGMP v2 or IGMP v3.

Used by