ALCATEL-IND1-PIM-MIB
Alcatel-Lucent EnterpriseThis module describes an authoritative enterprise-specific Simple
Network Management Protocol (SNMP) Management Information Base (MIB):
This proprietary MIB contains management information for
the configuration of PIM-SM and PIM-DM global configuration
parameters.
The right to make changes in specification and other information
contained in this document without prior notice is reserved.
No liability shall be assumed for any incidental, indirect, special, or
consequential damages whatsoever arising from or related to this
document or the information contained herein.
Vendors, end-users, and other interested parties are granted
non-exclusive license to use this specification in connection with
management of the products for which it is intended to be used.
Copyright (C) ALE USA Inc. 2014-2019
Copyright (C) 1995-2013 Alcatel-Lucent
ALL RIGHTS RESERVED WORLDWIDEsnmptranslate -m ALCATEL-IND1-PIM-MIB -Tpsnmpwalk -v2c -c <community> -m ALCATEL-IND1-PIM-MIB <host> 1.3.6.1.4.1.6486.801.1.2.1.10.6.1Imports
| ALCATEL-IND1-BASE | routingIND1Pim |
|---|---|
| INET-ADDRESS-MIB | InetAddress, InetAddressPrefixLength, InetAddressType |
| PIM-STD-MIB | pimInterfaceEntry |
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP |
| SNMPv2-SMI | Bits, Counter32, Integer32, IpAddress, MODULE-IDENTITY, MibIdentifier, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, iso |
| SNMPv2-TC | DisplayString, PhysAddress, RowStatus, TEXTUAL-CONVENTION, TruthValue |
OID tree
| Name | OID | Type | Access | Status |
|---|---|---|---|---|
| IalcatelIND1PIMMIB | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1 | |||
identity This module describes an authoritative enterprise-specific Simple
Network Management Protocol (SNMP) Management Information Base (MIB):
This proprietary MIB contains management information for
the configuration of PIM-SM and PIM-DM global configuration
parameters.
The right to make changes in specification and other information
contained in this document without prior notice is reserved.
No liability shall be assumed for any incidental, indirect, special, or
consequential damages whatsoever arising from or related to this
document or the information contained herein.
Vendors, end-users, and other interested parties are granted
non-exclusive license to use this specification in connection with
management of the products for which it is intended to be used.
Copyright (C) ALE USA Inc. 2014-2019
Copyright (C) 1995-2013 Alcatel-Lucent
ALL RIGHTS RESERVED WORLDWIDE | ||||
| NalaPimNotifications | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.0 | |||
| !alaPimNonBidirHello | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.0.1 | |||
notification · current An alaPimNonBidirHello notification signifies that a bidir-capable router has received a PIM hello from a non-bidir-capable router. This notification is generated whenever the counter alaPimsmNonBidirHelloMsgsRcvd is incremented, subject to the rate limit specified by alaPimsmNonBidirHelloNotificationPeriod. | ||||
| NalcatelIND1PIMMIBObjects | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1 | |||
| NalaPimsmGlobalConfig | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1 | |||
| SalaPimsmAdminStatus | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.1 | INTEGER | RW | |
scalar · INTEGER · read-write · current Administratively enables/disables the PIM-SM protocol on this router.
| ||||
| SalaPimsmMaxRPs | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.2 | Integer32 (1..100) | RW | |
scalar · Integer32 (1..100) · read-write · current The maximum number of C-RPs allowed in the PIM-SM domain. | ||||
| SalaPimsmProbeTime | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.3 | Integer32 (1..300) | RW | |
scalar · Integer32 (1..300) · read-write · current When NULL Registers are used, this is the time between sending a NULL Register and the Register- Suppression-Timer expiring unless it is restarted by receiving a Register-Stop.
| ||||
| SalaPimsmOldRegisterMessageSupport | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.4 | INTEGER | RW | |
scalar · INTEGER · read-write · current Specifies the application of the checksum function on received Register messages in the PIM-SM domain. When set to full(2), the checksum for a register message is computed for the entire packet (i.e. includes data). When set to header(1), the checksum is done only on the first 8 bytes of the packet. This variable is provided for interoperability reasons and may be required for Compatibility with older implementations of PIM-SM v2. This parameter must be set the same throughout the PIM-SM domain.
| ||||
| SalaPimsmAdminSPTConfig | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.5 | INTEGER | RW | |
scalar · INTEGER · read-write · current Administratively enables/disables SPT Switchover upon receiving the first data packet.
| ||||
| SalaPimsmRPThreshold | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.6 | Integer32 (0..2147483647) | RW | |
scalar · Integer32 (0..2147483647) · read-write · current Sets the RP threshold value (in bps) to be used in determining when to switch to native forwarding at the RP. The value of 0 disables the RP Threshold functionality. | ||||
| SalaPimsmV6AdminStatus | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.7 | INTEGER | RW | |
scalar · INTEGER · read-write · current Administratively enables/disables the PIM-SM IPv6 protocol on this router.
| ||||
| SalaPimsmV6SPTConfig | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.8 | INTEGER | RW | |
scalar · INTEGER · read-write · current Administratively enables/disables PIM IPv6 SPT Switchover upon receiving the first data packet.
| ||||
| SalaPimsmV6RPSwitchover | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.9 | INTEGER | RW | |
scalar · INTEGER · read-write · current Administratively enables/disables whether PIM IPv6 will attempt to switch to native forwarding at the RP upon receiving the first register-encapsulated packet.
| ||||
| SalaPimsmBidirStatus | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.10 | INTEGER | RW | |
scalar · INTEGER · read-write · current Administratively enables/disables the PIM BIDIR protocol on this router.
| ||||
| SalaPimsmBidirPeriodicInterval | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.11 | Integer32 (0..2000) | RW | |
scalar · Integer32 (0..2000) · read-write · current This is the interval at which the DF for each RPA will periodically announce its status in a Winner message. A value of 0 indicates that periodic messages will not be sent.
| ||||
| SalaPimsmBidirDFAbort | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.12 | INTEGER | RW | |
scalar · INTEGER · read-write · current Administratively enables/disables whether the DF election will be automatically aborted if a PIM hello is received from a PIM neighbor without the bidirectional capable option. By default, the DF election will still occur among those PIM routers that support BIDIR. By enabling this option, if a BIDIR- capable router receives a PIM hello from a non-BIDIR-capable router, the DF election is aborted.
| ||||
| SalaPimsmNonBidirHelloPeriod | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.13 | Unsigned32 (10..65535) | RW | |
scalar · Unsigned32 (10..65535) · read-write · current The minimum time that must elapse between alaPimNonBidirHello notifications originated by this router. The default value of 65535 represents an 'infinite' time, in which case, no alaPimNonBidirHello notifications are ever sent. The non-zero minimum allowed value provides resilience against propagation of denial-of-service attacks from the control plane to the network management plane.
| ||||
| SalaPimsmNonBidirHelloMsgsRcvd | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.14 | Counter32 | RO | |
scalar · Counter32 · read-only · current The number of PIM Hello messages that have been received by a BIDIR-capable device that do not have the Bidirectional Capable option. This counter is incremented if BIDIR mode is enabled on this router and a PIM Hello message is received from a PIM neighbor that does not include the Bidirectional Capable option. By default, the reception of these messages will not effect the BIDIR DF election. The alaPimsmBidirDFAbort object may be used to change the default behavior and have the DF election aborted whenever a BIDIR-capable router receives a PIM hello from a non-BIDIR-capable router. | ||||
| SalaPimsmNonBidirHelloAddressType | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.15 | InetAddressType | RO | |
scalar · InetAddressType · read-only · current The address type stored in alaPimsmNonBidirHelloOrigin. If no Non Bidir Hello messages have been received, this object is set to unknown(0). | ||||
| SalaPimsmNonBidirHelloOrigin | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.16 | InetAddress (SIZE (0 | 4 | 8 | 16 | 20)) | RO | |
scalar · InetAddress (SIZE (0 | 4 | 8 | 16 | 20)) · read-only · current The source address of the last Non Bidir Hello message received by this device. | ||||
| SalaPimsmV6BidirStatus | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.17 | INTEGER | RW | |
scalar · INTEGER · read-write · current Administratively enables/disables the PIM IPv6 BIDIR protocol on this router.
| ||||
| SalaPimsmRPHashStatus | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.18 | INTEGER | RW | |
scalar · INTEGER · read-write · current Administratively enables/disables applying the PIM hash function defined in RFC 4601 when selecting an RP from two or more equal group-range-to-RP mappings.
| ||||
| SalaPimsmBidirSsmCompat | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.19 | INTEGER | RW | |
scalar · INTEGER · read-write · current Administratively enables/disables whether PIM BIDIR will support receiving IGMPv3 source-specific joins and treat them as a (*,G) join. By default, IGMPv3 source-specific joins are ignored when PIM is operating in BIDIR mode.
| ||||
| SalaPimsmV6BidirSsmCompat | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.20 | INTEGER | RW | |
scalar · INTEGER · read-write · current Administratively enables/disables whether IPv6 PIM BIDIR will support receiving MLDv2 source-specific joins and treat them as a (*,G) join. By default, MLDv2 source-specific joins are ignored when PIM is operating in BIDIR mode.
| ||||
| SalaPimsmBidirFastJoin | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.21 | INTEGER | RW | |
scalar · INTEGER · read-write · current Administratively enables/disables whether PIM BIDIR will automatically create the routes in hardware as soon as the BIDIR (*,G) routes are learned. By default, this is disabled and the routes are not installed in hardware until the multicast traffic reaches the switch.
| ||||
| SalaPimsmV6BidirFastJoin | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.22 | INTEGER | RW | |
scalar · INTEGER · read-write · current Administratively enables/disables whether IPv6 PIM BIDIR will automatically create the routes in hardware as soon as the BIDIR (*,G) routes are learned. By default, this is disabled and the routes are not installed in hardware until the multicast traffic reaches the switch.
| ||||
| SalaPimsmAsmFastJoin | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.23 | INTEGER | RW | |
scalar · INTEGER · read-write · current Administratively enables/disables whether PIM ASM will automatically create the (*,G) routes in hardware as soon as the ASM (*,G) routes are learned. By default, this is disabled and the routes are not installed in hardware until the multicast traffic reaches the switch.
| ||||
| SalaPimsmV6AsmFastJoin | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.24 | INTEGER | RW | |
scalar · INTEGER · read-write · current Administratively enables/disables whether IPv6 PIM ASM will automatically create the (*,G) routes in hardware as soon as the ASM (*,G) routes are learned. By default, this is disabled and the routes are not installed in hardware until the multicast traffic reaches the switch.
| ||||
| SalaPimsmSsmFastJoin | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.25 | INTEGER | RW | |
scalar · INTEGER · read-write · current Administratively enables/disables whether PIM will automatically create the (S,G) routes in hardware as soon as the (S,G) routes are learned. This includes PIM Sparse Mode (S,G) routes as well as PIM SSM (S,G) routes. By default, this is disabled and the routes are not installed in hardware until the multicast traffic reaches the switch.
| ||||
| SalaPimsmV6SsmFastJoin | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.26 | INTEGER | RW | |
scalar · INTEGER · read-write · current Administratively enables/disables whether IPv6 PIM will automatically create the (S,G) routes in hardware as soon as the (S,G) routes are learned. This includes PIM Sparse Mode (S,G) routes as well as PIM SSM (S,G) routes. By default, this is disabled and the routes are not installed in hardware until the multicast traffic reaches the switch.
| ||||
| SalaPimsmRegisterRateLimit | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.27 | Integer32 (0..65535) | RW | |
scalar · Integer32 (0..65535) · read-write · current Configures the maximum number of PIM Register Packets that the Designated Router (DR) will send per second for each (S,G) entry. A default value of 0 indicates that no rate-limiting is being performed for outgoing PIM Register messages.
| ||||
| SalaPimsmV6RegisterRateLimit | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.28 | Integer32 (0..65535) | RW | |
scalar · Integer32 (0..65535) · read-write · current Configures the maximum number of IPv6 PIM Register Packets that the Designated Router (DR) will send per second for each (S,G) entry. A default value of 0 indicates that no rate-limiting is being performed for outgoing IPv6 PIM Register messages.
| ||||
| SalaPimsmRegisterMsgPackingStatus | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.29 | INTEGER | RW | |
scalar · INTEGER · read-write · current Administratively enables/disables the packing of PIM Null Register and Register Stop messages on this router. The value forceEnable(3) is used to automatically pack all Null Register and Register Stop messages to all RPs regardless of receiving verification from the RPs that null register packing is supported. If PIM Anycast-RP is being used, Register Message Packing should be enabled only if it is supported by all PIM anycast RP members in the RP set. The value forceEnable(3) is the recommended configuration with Anycast-RP in order to eliminate the initial stage of determining whether the new register message format for packing the messages is supported or not.
| ||||
| SalaPimsmV6RegisterMsgPackingStatus | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.30 | INTEGER | RW | |
scalar · INTEGER · read-write · current Administratively enables/disables the packing of PIM IPv6 Null Register and Register Stop messages on this router. The value forceEnable(3) is used to automatically pack all Null Register and Register Stop messages to all RPs regardless of receiving verification from the RPs that null register packing is supported. If PIM Anycast-RP is being used, Register Message Packing should be enabled only if it is supported by all PIM anycast RP members in the RP set. The value forceEnable(3) is the recommended configuration with Anycast-RP in order to eliminate the initial stage of determining whether the new register message format for packing the messages is supported or not.
| ||||
| SalaPimsmPackedRegisterMsgMtu | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.31 | Integer32 (0..9198) | RW | |
scalar · Integer32 (0..9198) · read-write · current Configures the maximum size used when sending packed PIM Null Register messages and Register Stop messages. This configuration can help control the MTU size of the PIM Null Register/Register Stop packets getting sent out.
| ||||
| SalaPimsmV6PackedRegisterMsgMtu | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.32 | Integer32 (0..9198) | RW | |
scalar · Integer32 (0..9198) · read-write · current Configures the maximum size used when sending packed PIM IPv6 Null Register messages and Register Stop messages. This configuration can help control the MTU size of the PIM Null Register/Register Stop packets getting sent out.
| ||||
| SalaPimsmPackedRegisterMsgDelay | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.33 | Unsigned32 (0..32767) | RW | |
scalar · Unsigned32 (0..32767) · read-write · current Configures the Packed Null Register Delay interval (in milliseconds). This is used to delay the sending of triggered Null Register messages and may be desirable to allow the packing of triggered Null Register messages due to bursts of traffic. This may be particularly useful when running Anycast-RP with the alaPimsmRegsterMsgPackingStatus set to forceEnable(3) to allow the packing of triggered Null Register messages due to the initial learning of the flows which may result in subsequent bursts of triggered Null Register packets to all Anycast-RP routers. The default value of 0 implies no deferred processing and will result in no packing of triggered Null Register messages.
| ||||
| SalaPimsmV6PackedRegisterMsgDelay | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.1.34 | Unsigned32 (0..32767) | RW | |
scalar · Unsigned32 (0..32767) · read-write · current Configures the IPv6 Packed Null Register Delay interval (in milliseconds). This is used to delay the sending of triggered Null Register messages and may be desirable to allow the packing of triggered Null Register messages due to bursts of traffic. This may be particularly useful when running Anycast-RP with the alaPimsmRegsterMsgPackingStatus set to forceEnable(3) to allow the packing of triggered Null Register messages due to the initial learning of the flows which may result in subsequent bursts of triggered Null Register packets to all Anycast-RP routers. The default value of 0 implies no deferred processing and will result in no packing of triggered Null Register messages.
| ||||
| NalaPimdmGlobalConfig | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.2 | |||
| SalaPimdmAdminStatus | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.2.1 | INTEGER | RW | |
scalar · INTEGER · read-write · current Administratively enables/disables the PIM-DM protocol on this router.
| ||||
| SalaPimdmStateRefreshTimeToLive | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.2.2 | Integer32 | RW | |
scalar · Integer32 · read-write · current The TTL to be used by this router's originated State Refresh messages if the data packet's TTL is not recorded. | ||||
| SalaPimdmStateRefreshLimitInterval | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.2.3 | TimeTicks | RW | |
scalar · TimeTicks · read-write · current This router will not forward successive State Refresh messages received at less than this interval. | ||||
| SalaPimdmV6AdminStatus | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.2.4 | INTEGER | RW | |
scalar · INTEGER · read-write · current Administratively enables/disables the PIM-DM IPv6 protocol on this router.
| ||||
| TalaPimdmDenseGroupTable | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.2.5 | NA | ||
table · not-accessible · current This table is used to manage configuration of dense groups. If the group prefixes configured for two or more rows in this table overlap, the row with the greatest value of alaPimdmDenseGroupGrpPrefixLength is used for the overlapping range. | ||||
| RalaPimdmDenseGroupEntry | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.2.5.1 | NA | ||
row · not-accessible · current An entry (conceptual row) in the alaPimdmDenseGroupTable. This entry is preserved on agent restart. | ||||
| CalaPimdmDenseGroupAddressType | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.2.5.1.1 | InetAddressType | NA | |
column · InetAddressType · not-accessible · current The address type of this entry. | ||||
| CalaPimdmDenseGroupGrpAddress | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.2.5.1.2 | InetAddress (SIZE (4 | 8 | 16 | 20)) | NA | |
column · InetAddress (SIZE (4 | 8 | 16 | 20)) · not-accessible · current The multicast group address that, when combined with alaPimdmDenseGroupGrpPrefixLength, gives the group prefix for this entry. The InetAddressType is given by the alaPimdmDenseGroupAddressType object. This address object is only significant up to alaPimdmDenseGroupGrpPrefixLength bits. The remainder of the address bits are zero. This is especially important for this index field, which is part of the index of this entry. Any non-zero bits would signify an entirely different entry. | ||||
| CalaPimdmDenseGroupGrpPrefixLength | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.2.5.1.3 | InetAddressPrefixLength (4..128) | NA | |
column · InetAddressPrefixLength (4..128) · not-accessible · current The multicast group prefix length that, when combined with alaPimdmDenseGroupGrpAddress, gives the group prefix for this entry. The InetAddressType is given by the alaPimdmDenseGroupAddressType object. If alaPimdmDenseGroupAddressType is 'ipv4' or 'ipv4z', this object must be in the range 4..32. If alaPimdmDenseGroupGrpAddressType is 'ipv6' or 'ipv6z', this object must be in the range 8..128. | ||||
| CalaPimdmDenseGroupOverrideDynamic | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.2.5.1.4 | TruthValue | RC | |
column · TruthValue · read-create · current Whether this dense group configuration will override other group mappings in this group prefix. If this object is TRUE, then it will override: - RP information learned dynamically for groups in this group prefix. - RP information configured in alaPimdmDenseGroupTable with alaPimdmDenseGroupOverrideDynamic set to FALSE. See pimGroupMappingTable for details. | ||||
| CalaPimdmDenseGroupPrecedence | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.2.5.1.5 | Unsigned32 (0..65535) | RC | |
column · Unsigned32 (0..65535) · read-create · current The value for pimGroupMappingPrecedence to be used for this static RP configuration. This allows fine control over which configuration is overridden by this static configuration. If alaPimdmDenseGroupOverrideDynamic is set to TRUE, all dynamic RP configuration is overridden by this static configuration, whatever the value of this object. The absolute values of this object have a significance only on the local router and do not need to be coordinated with other routers. A setting of this object may have different effects when applied to other routers. Do not use this object unless fine control of static RP behavior on the local router is required. | ||||
| CalaPimdmDenseGroupRowStatus | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.2.5.1.6 | RowStatus | RC | |
column · RowStatus · read-create · current The status of this row, by which rows in this table can be created and destroyed. All writeable objects in this entry can be modified when the status of this entry is active(1). | ||||
| NalaPimGlobalConfig | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.3 | |||
| SalaPimBfdStatus | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.3.1 | INTEGER | RW | |
scalar · INTEGER · read-write · current Administratively enables/disables PIM with the BFD protocol on this router.
| ||||
| SalaPimBfdAllInterfaceStatus | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.3.2 | INTEGER | RW | |
scalar · INTEGER · read-write · current Administratively enables/disables BFD for all PIM interfaces on this router.
| ||||
| SalaPimMoFRRStatus | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.3.3 | INTEGER | RW | |
scalar · INTEGER · read-write · current Administratively enables/disables MoFRR (Multicast only Fast Re-Route) on this router.
| ||||
| SalaPimMoFRRAllRouteStatus | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.3.4 | INTEGER | RW | |
scalar · INTEGER · read-write · current By default, MoFRR is only applied to multicast routes that have local clients. Enabling alaPimMoFRRAllRouteStatus will enable MoFRR on all routes whether there are local clients or not. alaPimMoFRRStatus must be enabled for this to take effect.
| ||||
| TalaPimInterfaceAugTable | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.3.5 | NA | ||
table · not-accessible · current Expansion for pimInterfaceTable | ||||
| RalaPimInterfaceAugEntry | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.3.5.1 | NA | ||
| CalaPimInterfaceBfdStatus | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.3.5.1.1 | INTEGER | RW | |
column · INTEGER · read-write · current Enables/Disables BFD for particular interfaces of PIM.
| ||||
| CalaPimInterfaceJoinPruneMtu | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.3.5.1.2 | Integer32 (0..9198) | RW | |
column · Integer32 (0..9198) · read-write · current Configures the maximum size used when sending PIM Join/Prune messages on the interface. The actual maximum size used for the PIM Join/Prune messages will be the smaller of the IP MTU value of the interface and the configured alaPimInterfaceJoinPruneMtu value. This configuration can help control the MTU size of the PIM Join/Prune packets getting sent out. The default value of 0 means that the IP MTU value of the interface will be used in determining the maximum size of the PIM Join/Prune packets and no other limitation will be enforced.
| ||||
| CalaPimInterfaceJoinPruneDelay | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.3.5.1.3 | Unsigned32 (0..32767) | RW | |
column · Unsigned32 (0..32767) · read-write · current Configures the JoinPrune Delay interval (in milliseconds). This is used to delay the sending of triggered Join/Prune messages and may be desirable to allow the packing of triggered Join/Prune messages due to bursts of protocol messages which may result in subsequent bursts of triggered Join/Prune packets.. The default value of 0 implies no deferred processing and will result in no packing of triggered Join/Prune updates.
| ||||
| SalaPimMbrAllSourcesStatus | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.3.6 | INTEGER | RW | |
scalar · INTEGER · read-write · current Administratively enables/disables PIM to notify DVMRP about the routes to all multicast sources learned instead of just the directly connected subnets so that these routes can be advertised in the DVMRP domain via standard DVMRP mechanisms. This object is only applicable if the router is operating as a Multicast Border Router.
| ||||
| SalaPimMbrOperStatus | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.3.7 | INTEGER | RO | |
scalar · INTEGER · read-only · current Whether MBR is currently enabled/disabled for PIM.
| ||||
| SalaPimV6BfdStatus | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.3.8 | INTEGER | RW | |
scalar · INTEGER · read-write · current Administratively enables/disables PIM IPv6 with the BFD protocol on this router.
| ||||
| SalaPimV6BfdAllInterfaceStatus | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.3.9 | INTEGER | RW | |
scalar · INTEGER · read-write · current Administratively enables/disables BFD for all PIM IPv6 interfaces on this router.
| ||||
| SalaPimJoinPruneMsgPackingStatus | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.3.10 | INTEGER | RW | |
scalar · INTEGER · read-write · current Administratively enables/disables the packing of PIM Join/Prune messages on this router.
| ||||
| SalaPimV6JoinPruneMsgPackingStatus | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.1.3.11 | INTEGER | RW | |
scalar · INTEGER · read-write · current Administratively enables/disables the packing of PIM IPv6 Join/Prune messages on this router.
| ||||
| NalcatelIND1PIMMIBConformance | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.2 | |||
| NalcatelIND1PIMMIBCompliances | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.2.1 | |||
| MalaPimsmCompliance | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.2.1.1 | |||
compliance · current The compliance statement for routers running PIM Sparse Mode and implementing the ALCATEL-IND1-PIM MIB. | ||||
| MalaPimdmCompliance | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.2.1.2 | |||
compliance · current The compliance statement for routers running PIM Dense Mode and implementing the ALCATEL-IND1-PIM MIB. | ||||
| NalcatelIND1PIMMIBGroups | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.2.2 | |||
| GalaPimsmConfigMIBGroup | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.2.2.1 | |||
group · current A collection of objects to support management of global configuration parameters of PIM Sparse Mode routers.
| ||||
| GalaPimdmConfigMIBGroup | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.2.2.2 | |||
group · current A collection of objects to support management of global configuration parameters of PIM Dense Mode routers. | ||||
| GalaPimConfigMIBGroup | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.2.2.3 | |||
group · current A collection of objects to support management of global configuration parameters of PIM routers.
| ||||
| GalaPimOptionalGroup | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.2.2.4 | |||
group · current PIM objects to stop the tools from complaining | ||||
| GalaPimNotificationGroup | 1.3.6.1.4.1.6486.801.1.2.1.10.6.1.2.2.5 | |||
Traps / Notifications
- alaPimNonBidirHello
1.3.6.1.4.1.6486.801.1.2.1.10.6.1.0.1