ALCATEL-IND1-CHASSIS-MIB
Alcatel-Lucent EnterpriseThis module describes an authoritative enterprise-specific Simple
etwork Management Protocol (SNMP) Management Information Base (MIB):
For the OmniSwitch Product Line, this is the Chassis Supervision
Chassis MIB
for managing physical chassis objects not covered in the IETF
Entity MIB (rfc 2737).
The right to make changes in specification and other information
contained in this document without prior notice is reserved.
No liability shall be assumed for any incidental, indirect, special, or
consequential damages whatsoever arising from or related to this
document or the information contained herein.
Vendors, end-users, and other interested parties are granted
non-exclusive license to use this specification in connection with
management of the products for which it is intended to be used.
Copyright (C) ALE USA Inc. 2014-2019
Copyright (C) 1995-2013 Alcatel-Lucent
ALL RIGHTS RESERVED WORLDWIDEsnmptranslate -m ALCATEL-IND1-CHASSIS-MIB -Tpsnmpwalk -v2c -c <community> -m ALCATEL-IND1-CHASSIS-MIB <host> 1.3.6.1.4.1.6486.801.1.1.1.3.1Imports
| ALCATEL-IND1-BASE | hardentIND1Chassis, hardentIND1Physical |
|---|---|
| ENTITY-MIB | PhysicalIndex, entPhysicalIndex |
| SNMP-FRAMEWORK-MIB | SnmpAdminString |
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP |
| SNMPv2-SMI | Bits, Counter32, Integer32, IpAddress, MODULE-IDENTITY, MibIdentifier, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, iso |
| SNMPv2-TC | DisplayString, MacAddress, PhysAddress, TEXTUAL-CONVENTION, TruthValue |
OID tree
| Name | OID | Type | Access | Status | Example | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| NalcatelIND1ChassisPhysMIBObjects | 1.3.6.1.4.1.6486.801.1.1.1.1.1 | ||||||||||||
node · current Branch For Chassis Supervision Chassis Physical MIB Subsystem Managed Objects. | |||||||||||||
| TchasEntPhysicalTable | 1.3.6.1.4.1.6486.801.1.1.1.1.1.1 | NA | |||||||||||
table · not-accessible · current This table contains one row per physical entity. It is an extension for the entity physical table (rfc 2737) that is instantiated for every physical entity object. The fields are not always significant for every object. | |||||||||||||
| RchasEntPhysicalEntry | 1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1 | NA | |||||||||||
| CchasEntPhysAdminStatus | 1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.1 | INTEGER | RW | ||||||||||
column · INTEGER · read-write · current All modules (even empty slots) are in unknown state when the chassis
first powers up.
Chassis status possible value:
powerOn <=> powered up
Control Module possible value:
powerOn <=> CM up and running
reset <=> CM reset
takeover <=> Secondary CM takes over
resetAll <=> resets the whole switch
vcTakeover <=> Reloads master chassis from the current working directory,
which initiates a VC takeover.
vcResetAll <=> resets entire VC.
NI status possible value:
powerOn <=> NI is either powered (up or down) or waiting to be powered
whenever more power is available. This admin status has not full meaning
without chasEntPhysOperStatus
powerOff <=> NI down and unpowered and NI will not be powered until user
requests it, a failover happens or a reboot happens
reset <=> NI reset
FABRIC status possible value:
powerOn <=> FABRIC is powered
powerOff <=> FABRIC is unpowered
standby <=> FABRIC is powered and requested to be redundant (inactive)
Daughter board status possible value:
powerOn <=> DB up and running
reset <=> DB reset (TO BE CONFIRMED)
Power supply status possible value:
powerOn <=> PS up
| |||||||||||||
| CchasEntPhysOperStatus | 1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.2 | INTEGER | RO | up(1) | |||||||||
column · INTEGER · read-only · current All modules (even empty slots) are in unknown state when the chassis
first powers up.
Chassis status possible value :
up <=> powered up
Control Module possible value :
notPresent <=> CM not present
up <=> CM up and running
down <=> CM down and powered
secondary <=> CM in secondary mode and running
NI status possible value :
notPresent <=> NI not present
up <=> NI up and running
down <=> NI down and powered
unpowered <=> NI unpowered because there is not enough power in the system
(chasEntPhysAdminStatus = powerOn) or because the NI has to be OFF
(chasEntPhysAdminStatus = powerOff). This operational status has
not full meaning without chasEntPhysAdminStatus
Fabric status possible value :
master <=> up and acting as master
up <=> up and acting as slave
secondary <=> secondary mode for redundancy
Daughter board status possible value :
notPresent <=> DB not present
up <=> DB up and running
down <=> DB down and powered
Power supply status possible value :
up <=> PS up
down <=> PS administratively down
unpowered <=> PS not plugged in
pwrsave <=> chassis in powersave mode, supply turned off
Fan Tray status possible value :
up <=> powered up
down <=> powered down
fault <=> fault detected
| |||||||||||||
| CchasEntPhysPower | 1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.3 | Integer32 (0..65535) | RO | ||||||||||
column · Integer32 (0..65535) · read-only · current This value is only applicable to the NI, PS and Control Modules. It corresponds to a a static value for the power consumption of an NI module or Control Module. This value is in Watts. | |||||||||||||
| CchasEntPhysModuleType | 1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.4 | SnmpAdminString | RO | ||||||||||
column · SnmpAdminString · read-only · current This object is the unique Module Type or ID from the entities eeprom. This value is guarrantteed to be unique to each type of Module. This value is only intended for Alcatel internal use. | |||||||||||||
| CchasEntPhysPartNumber | 1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.5 | SnmpAdminString (SIZE (0..16)) | RO | ||||||||||
column · SnmpAdminString (SIZE (0..16)) · read-only · current This object contains the Alcatel Part Number for the entity. This value is used to identify what is needed when placing orders with Alcatel. | |||||||||||||
| CchasEntPhysLedStatusOk1 | 1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.6 | ChasEntPhysLed | RO | ||||||||||
column · ChasEntPhysLed · read-only · current Chassis Management Module (CMM) front panel LED OK1 status indication | |||||||||||||
| CchasEntPhysLedStatusOk2 | 1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.7 | ChasEntPhysLed | RO | ||||||||||
column · ChasEntPhysLed · read-only · current Chassis Management Module (CMM) front panel LED OK2 status indication | |||||||||||||
| CchasEntPhysLedStatusPrimaryCMM | 1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.8 | ChasEntPhysLed | RO | ||||||||||
column · ChasEntPhysLed · read-only · current Chassis Management Module (CMM) front panel LED Primary chassis indication | |||||||||||||
| CchasEntPhysLedStatusSecondaryCMM | 1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.9 | ChasEntPhysLed | RO | ||||||||||
column · ChasEntPhysLed · read-only · current Chassis Management Module (CMM) front panel LED Secondary chassis indication | |||||||||||||
| CchasEntPhysLedStatusTemperature | 1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.10 | ChasEntPhysLed | RO | ||||||||||
column · ChasEntPhysLed · read-only · current Chassis Management Module (CMM) front panel LED temperature status indication | |||||||||||||
| CchasEntPhysLedStatusFan | 1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.11 | ChasEntPhysLed | RO | ||||||||||
column · ChasEntPhysLed · read-only · current For Hawk stacks used as a fan group status LED. For eagle CMM's user instead: Fan 1 (top left), Fan 2 (top right), Fan 3 (rear) | |||||||||||||
| CchasEntPhysLedStatusBackupPS | 1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.12 | ChasEntPhysLed | RO | ||||||||||
column · ChasEntPhysLed · read-only · current Chassis backup power supply status indication | |||||||||||||
| CchasEntPhysLedStatusInternalPS | 1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.13 | ChasEntPhysLed | RO | ||||||||||
column · ChasEntPhysLed · read-only · current Chassis internal power supply status indication | |||||||||||||
| CchasEntPhysLedStatusControl | 1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.14 | ChasEntPhysLed | RO | ||||||||||
column · ChasEntPhysLed · read-only · current Chassis control status | |||||||||||||
| CchasEntPhysLedStatusFabric | 1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.15 | ChasEntPhysLed | RO | ||||||||||
column · ChasEntPhysLed · read-only · current Chassis Management Module (CMM) Fabric status indication | |||||||||||||
| CchasEntPhysLedStatusPS | 1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.16 | ChasEntPhysLed | RO | ||||||||||
column · ChasEntPhysLed · read-only · current Chassis Power Supply Unit status indication | |||||||||||||
| CchasEntPhysAsic1Rev | 1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.17 | SnmpAdminString (SIZE (0..14)) | RO | ||||||||||
column · SnmpAdminString (SIZE (0..14)) · read-only · current This object contains the ASIC revision Number of the ni entity | |||||||||||||
| CchasEntPhysAsic2Rev | 1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.18 | SnmpAdminString (SIZE (0..14)) | RO | ||||||||||
column · SnmpAdminString (SIZE (0..14)) · read-only · current This object contains the ASIC revision Number of the ni entity | |||||||||||||
| CchasEntPhysAsic3Rev | 1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.19 | SnmpAdminString (SIZE (0..14)) | RO | ||||||||||
column · SnmpAdminString (SIZE (0..14)) · read-only · current This object contains the ASIC revision Number of the ni entity | |||||||||||||
| CchasEntPhysAsic4Rev | 1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.20 | SnmpAdminString (SIZE (0..14)) | RO | ||||||||||
column · SnmpAdminString (SIZE (0..14)) · read-only · current This object contains the ASIC revision Number of the ni entity | |||||||||||||
| CchasEntPhysAsic5Rev | 1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.21 | SnmpAdminString (SIZE (0..14)) | RO | ||||||||||
column · SnmpAdminString (SIZE (0..14)) · read-only · current This object contains the ASIC revision Number of the ni entity | |||||||||||||
| CchasEntPhysAsic6Rev | 1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.22 | SnmpAdminString (SIZE (0..14)) | RO | ||||||||||
column · SnmpAdminString (SIZE (0..14)) · read-only · current This object contains the ASIC revision Number of the ni entity | |||||||||||||
| CchasEntPhysCpldRev | 1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.23 | SnmpAdminString (SIZE (0..14)) | RO | ||||||||||
column · SnmpAdminString (SIZE (0..14)) · read-only · current This object contains the CPLD revision Number of the ni entity | |||||||||||||
| CchasEntPhysDaughterFpga1Rev | 1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.24 | SnmpAdminString (SIZE (0..14)) | RO | ||||||||||
column · SnmpAdminString (SIZE (0..14)) · read-only · current This object contains the daughter fpga revision Number of the ni entity | |||||||||||||
| CchasEntPhysDaughterFpga2Rev | 1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.25 | SnmpAdminString (SIZE (0..14)) | RO | ||||||||||
column · SnmpAdminString (SIZE (0..14)) · read-only · current This object contains the daughter fpga revision Number of the ni entity | |||||||||||||
| CchasEntPhysNiNum | 1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.26 | Integer32 (0..65535) | RO | ||||||||||
column · Integer32 (0..65535) · read-only · current This value is only applicable to the NI. It indicates an NI associated with this physicalEntry | |||||||||||||
| CchasEntPhysGbicNum | 1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.27 | Integer32 (0..65535) | RO | ||||||||||
column · Integer32 (0..65535) · read-only · current This value is only applicable to the NI. It indicates a gbic associated with this ni | |||||||||||||
| CchasEntPhysWaveLen | 1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.28 | Integer32 (0..65535) | RO | ||||||||||
column · Integer32 (0..65535) · read-only · current This object contains the wave length of a SFP device | |||||||||||||
| CchasEntPhysUbootRev | 1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.29 | SnmpAdminString (SIZE (0..14)) | RO | ||||||||||
column · SnmpAdminString (SIZE (0..14)) · read-only · current This object contains the uboot version Number of the ni entity | |||||||||||||
| CchasEntPhysUbootMinibootRev | 1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.30 | SnmpAdminString (SIZE (0..14)) | RO | ||||||||||
column · SnmpAdminString (SIZE (0..14)) · read-only · current This object contains the uboot miniboot version Number of the ni entity | |||||||||||||
| CchasEntPhysMacAddress | 1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.31 | MacAddress | RO | ||||||||||
column · MacAddress · read-only · current This object contains the MAC address of the ni entity | |||||||||||||
| CchasEntPhysCpuModel | 1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.32 | SnmpAdminString (SIZE (0..32)) | RO | ||||||||||
column · SnmpAdminString (SIZE (0..32)) · read-only · current This object contains the model description of the cmm/ni cpu | |||||||||||||
| CchasEntPhysAirflow | 1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.33 | INTEGER | RO | ||||||||||
column · INTEGER · read-only · current Chassis PS fan airflow direction
| |||||||||||||
| CchasEntPhysPowerUsed | 1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.34 | Integer32 (0..65535) | RO | ||||||||||
column · Integer32 (0..65535) · read-only · current This value is only applicable to the PS. It is the current reading for the power usage of the PS. This value is in Watts. | |||||||||||||
| CchasEntPhysPowerType | 1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.35 | INTEGER | RO | ||||||||||
column · INTEGER · read-only · current This object is the type of the power supply, It corresponds to AC, DC or BPS. This value is only intended for Alcatel internal use.
| |||||||||||||
| CchasEntPowerSupplyName | 1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.36 | SnmpAdminString (SIZE (0..32)) | RW | ||||||||||
column · SnmpAdminString (SIZE (0..32)) · read-write · current The name of the power supply of this entry. | |||||||||||||
| CchasEntPowerSupplyType | 1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.37 | INTEGER | RW | ||||||||||
column · INTEGER · read-write · current Type of power supply.
| |||||||||||||
| CchasEntPowerSupplyInputType | 1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.38 | INTEGER | RW | ||||||||||
column · INTEGER · read-write · current Type of power supply input.
| |||||||||||||
| CchasEntPowerSupplyWattage | 1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.39 | Unsigned32 | RW | ||||||||||
column · Unsigned32 · read-write · current The wattage of power supply. | |||||||||||||
| CchasEntPowerSupplyVoltage | 1.3.6.1.4.1.6486.801.1.1.1.1.1.1.1.40 | Unsigned32 (0 | 24 | 48 | 54) | RO | ||||||||||
column · Unsigned32 (0 | 24 | 48 | 54) · read-only · current The Voltage of power supply. | |||||||||||||
| TchasEntTemperatureTable | 1.3.6.1.4.1.6486.801.1.1.1.1.1.2 | NA | |||||||||||
table · not-accessible · current This table contains one row per temperature sensor located on an entity represented by the associated row in the entPhysicalTable. | |||||||||||||
| RchasEntTemperatureEntry | 1.3.6.1.4.1.6486.801.1.1.1.1.1.2.1 | NA | |||||||||||
row · not-accessible · current Information about a particular physical temperature sensor.
| |||||||||||||
| CchasEntTempCurrent | 1.3.6.1.4.1.6486.801.1.1.1.1.1.2.1.1 | Integer32 (0..200) | RO | ||||||||||
column · Integer32 (0..200) · read-only · current This object indicates the current output of the temperature sensor in degrees Celsius. | |||||||||||||
| CchasEntTempThreshold | 1.3.6.1.4.1.6486.801.1.1.1.1.1.2.1.2 | Integer32 (1..150) | RO | ||||||||||
column · Integer32 (1..150) · read-only · current This object is the threshold temperature in degrees Celsius for the sensor. When the value of chasEntTempCurrent exceeds this value, a temperature notification is provided to the user. | |||||||||||||
| CchasEntTempDangerThreshold | 1.3.6.1.4.1.6486.801.1.1.1.1.1.2.1.3 | Integer32 (30..150) | RO | ||||||||||
column · Integer32 (30..150) · read-only · current This object is the danger threshold temperature in degrees Celsius for the sensor. When the value of chasEntTempCurrent exceeds this value, the associated physical entity is powered down. | |||||||||||||
| CchasEntTempStatus | 1.3.6.1.4.1.6486.801.1.1.1.1.1.2.1.4 | INTEGER | RO | ||||||||||
column · INTEGER · read-only · current This object is the status value of the temperature sensor. It reflects the temperature relative to the chasEntTempThreshold and chasEntTempDangerThreshold values.
| |||||||||||||
| NalcatelIND1ChassisPhysMIBConformance | 1.3.6.1.4.1.6486.801.1.1.1.1.2 | ||||||||||||
node · current Branch For Chassis Supervision Chassis Physical MIB Subsystem Conformance Information. | |||||||||||||
| NalcatelIND1ChassisPhysMIBGroups | 1.3.6.1.4.1.6486.801.1.1.1.1.2.1 | ||||||||||||
node · current Branch For Chassis Supervision Chassis Physical MIB Subsystem Units Of Conformance. | |||||||||||||
| GchasEntPhysicalGroup | 1.3.6.1.4.1.6486.801.1.1.1.1.2.1.1 | ||||||||||||
group · current Chassis (inclosure) Entity Physical Group.
| |||||||||||||
| GchassisPhysNotificationGroup | 1.3.6.1.4.1.6486.801.1.1.1.1.2.1.2 | ||||||||||||
group · current Chassis Supervision Physical Notification Group. | |||||||||||||
| GchassisTemperatureGroup | 1.3.6.1.4.1.6486.801.1.1.1.1.2.1.3 | ||||||||||||
group · current Chassis Supervision Temprature Group. | |||||||||||||
| NalcatelIND1ChassisPhysMIBCompliances | 1.3.6.1.4.1.6486.801.1.1.1.1.2.2 | ||||||||||||
node · current Branch For Chassis Supervision Chassis Physical MIB Subsystem Compliance Statements. | |||||||||||||
| MalcatelIND1ChassisPhysMIBCompliance | 1.3.6.1.4.1.6486.801.1.1.1.1.2.2.1 | ||||||||||||
compliance · current Compliance statement for Chassis Supervision Physical. | |||||||||||||
| IalcatelIND1ChassisMIB | 1.3.6.1.4.1.6486.801.1.1.1.3.1 | ||||||||||||
identity This module describes an authoritative enterprise-specific Simple
etwork Management Protocol (SNMP) Management Information Base (MIB):
For the OmniSwitch Product Line, this is the Chassis Supervision
Chassis MIB
for managing physical chassis objects not covered in the IETF
Entity MIB (rfc 2737).
The right to make changes in specification and other information
contained in this document without prior notice is reserved.
No liability shall be assumed for any incidental, indirect, special, or
consequential damages whatsoever arising from or related to this
document or the information contained herein.
Vendors, end-users, and other interested parties are granted
non-exclusive license to use this specification in connection with
management of the products for which it is intended to be used.
Copyright (C) ALE USA Inc. 2014-2019
Copyright (C) 1995-2013 Alcatel-Lucent
ALL RIGHTS RESERVED WORLDWIDE | |||||||||||||
| NalcatelIND1ChassisMIBNotifications | 1.3.6.1.4.1.6486.801.1.1.1.3.1.0 | ||||||||||||
node · current Branch For Chassis MIB Subsystem Notifications. | |||||||||||||
| !chassisTrapsStr | 1.3.6.1.4.1.6486.801.1.1.1.3.1.0.1 | ||||||||||||
notification · current A Software Trouble report is sent by whatever application encountering a problem during its execution and would want to aware the user of for maintenance purpose. | |||||||||||||
| !chassisTrapsAlert | 1.3.6.1.4.1.6486.801.1.1.1.3.1.0.2 | ||||||||||||
notification · current generic trap notifying something changed in the chassis whatever it's a failure or not | |||||||||||||
| !chassisTrapsStateChange | 1.3.6.1.4.1.6486.801.1.1.1.3.1.0.3 | ||||||||||||
notification · current A status change was detected | |||||||||||||
| !chasTrapsBPSLessAllocSysPwr | 1.3.6.1.4.1.6486.801.1.1.1.3.1.0.4 | ||||||||||||
notification · current Insufficient system power given by BPS | |||||||||||||
| !chasTrapsBPSStateChange | 1.3.6.1.4.1.6486.801.1.1.1.3.1.0.5 | ||||||||||||
notification · current BPS power supplies insertion/removal trap | |||||||||||||
| !chasTrapsNiBPSFETStateChange | 1.3.6.1.4.1.6486.801.1.1.1.3.1.0.6 | ||||||||||||
notification · current BPS power supplies FET state change trap | |||||||||||||
| !chasTrapsBPSFwUpgradeAlert | 1.3.6.1.4.1.6486.801.1.1.1.3.1.0.7 | ||||||||||||
notification · current BPS FW upgrade requirment alert trap | |||||||||||||
| !chassisTrapsImageSigCheckFailed | 1.3.6.1.4.1.6486.801.1.1.1.3.1.0.8 | ||||||||||||
notification · current Image signature verification failed | |||||||||||||
| !chassisTrapsResetToFactory | 1.3.6.1.4.1.6486.801.1.1.1.3.1.0.9 | ||||||||||||
notification · current Trap to notify the reset to factory | |||||||||||||
| NalcatelIND1ChassisMIBObjects | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1 | ||||||||||||
node · current Branch For Chassis Supervision Chassis MIB Subsystem Managed Objects. | |||||||||||||
| TchasControlModuleTable | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.1 | NA | |||||||||||
table · not-accessible · current This table contains one row for the primary control module. | |||||||||||||
| RchasControlModuleEntry | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.1.1 | NA | |||||||||||
row · not-accessible · current Information about the primary control module. This table is an extension of the entity physical table but this class is instanciated only for a the primary control module that has a particular Index. When operatiing in virtual chassis mode only the master primary control module is instanciated
| |||||||||||||
| CchasControlActivateTimeout | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.1.1.1 | Integer32 (0..900) | RW | 0 | |||||||||
column · Integer32 (0..900) · read-write · current This value is in seconds. It represents how much time before the switch automatically falls back to the certified version. This value is set via the Activate(reload working) cli command. An Activate reboot must be initiated via the primary CMM and that the timeout value can be accessed via user interface to the primary CMM only. After the Activate reboot has been initiated, a timeout will occur (i.e., an Activate Timeout) at the timeout value specified by the user. If a reboot cancel has not been received prior to the timeout expiration, the primary CMM will automatically reboot (i.e., re-reboot) using the certified configuration. This ensures that an automatic backup reboot is available using the certified configuration in the event that the user is unable to interface with primary CMM as a result of the attempted Activate reboot. If the Activate reboot is successful, the user cancels the backup reboot via the normal reboot cancellation process (i.e., a zero value is written for the object chasControlDelayedRebootTimer). Example values from LibreNMS test devices
| |||||||||||||
| CchasControlVersionMngt | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.1.1.2 | INTEGER | RW | certifySynchro(2) | |||||||||
column · INTEGER · read-write · current For the primary this means:
notSignificant - No command applied.
certifySynchro - Copy the file from the working to the certified
directory and from the primary to the secondary
(reboot of the secondary).
certifyNoSynchro - Copy the file from the working to the certified
directory.
flashSynchro - Copy the file from the primary to the secondary
(reboot of the secondary).
restore - Copy the file from the certified directory to the
working directory.
activate - Reload from the working directory. Activate can be
scheduled.
issu - In Service Software Upgrade (ISSU).
shutdown - Shutdown chassis specified by chasControlChassisId.
Halts and powers off NIs, halts primary and
secondary CMMs.
vcConvert - Copy the image files from the running directory
to the working directory.
Example values from LibreNMS test devices
| |||||||||||||
| CchasControlDelayedActivateTimer | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.1.1.3 | Unsigned32 (0..31622400) | RW | 0 | |||||||||
column · Unsigned32 (0..31622400) · read-write · current Timer value in seconds used to initiate a delayed activate of the primary
CMM. Writing this object to a non-zero value results in CMM reboot of the
working directory following expiration of the specified activate timer delay.
Writing this object to zero results in an immediately activate process.
It is now adjusted to wait a maximum of 366 days.Example values from LibreNMS test devices
| |||||||||||||
| CchasControlCertifyStatus | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.1.1.4 | INTEGER | RO | certified(3) | |||||||||
column · INTEGER · read-only · current Returned value indicates if the control module has been certified (that is the working directory matches the certified directory)
Example values from LibreNMS test devices
| |||||||||||||
| CchasControlSynchronizationStatus | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.1.1.5 | INTEGER | RO | synchronized(4) | |||||||||
column · INTEGER · read-only · current Returned value indicates if the control module has been synchronized (that is the working directory matches the working directory on the other control module(s) if present). Returned value is monoControlModule when no other control module is present.
Example values from LibreNMS test devices
| |||||||||||||
| CchasControlAcrossCmmWorkingSynchroStatus | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.1.1.6 | INTEGER | RO | yes(4) | |||||||||
column · INTEGER · read-only · current Returned value indicates if the /working has been synchronized across the CMMs (that is the working directory matches the working directory on all CMMs if present)
Example values from LibreNMS test devices
| |||||||||||||
| CchasControlAcrossCmmCertifiedSynchroStatus | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.1.1.7 | INTEGER | RO | yes(4) | |||||||||
column · INTEGER · read-only · current Returned value indicates if the /certified has been synchronized across the CMMs if present)
Example values from LibreNMS test devices
| |||||||||||||
| CchasControlNextRunningVersion | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.1.1.8 | SnmpAdminString | RO | working | |||||||||
column · SnmpAdminString · read-only · current The pathname for the image directory that will be used on the next reload. Value may be /flash/certified or /flash/<working directory name>. Example values from LibreNMS test devices
| |||||||||||||
| CchasControlCurrentRunningVersion | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.1.1.9 | SnmpAdminString | RW | working | |||||||||
column · SnmpAdminString · read-write · current The pathname of the image directory to the version that is currently executing. Value may be /flash/certified or /flash/<working directory name>. Example values from LibreNMS test devices
| |||||||||||||
| CchasControlWorkingVersion | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.1.1.10 | SnmpAdminString | RW | | |||||||||
column · SnmpAdminString · read-write · current The path to the currently specified working image directory. Value may be /flash/certified or /flash/<working directory name>. Example values from LibreNMS test devices
| |||||||||||||
| CchasControlRedundancyTime | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.1.1.11 | Integer32 (0..900) | RW | 0 | |||||||||
column · Integer32 (0..900) · read-write · current Time in minutes that the running image must stay up without error before a subsequent error reset will restart the board from the running image. If a CMM in dual-CMM switch fails after a reload and before chasControlRedundancyTime expires, both CMMs will be rebooted from the certified version. Example values from LibreNMS test devices
| |||||||||||||
| CchasControlEmpIpAddress | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.1.1.12 | IpAddress | RW | deprecated | 0.0.0.0 | ||||||||
column · IpAddress · read-write · deprecated This object is deprecated. Instead use alaInterfaceTable(ALCATEL-IND1-IP-MIB) when configuring EMP interfaces. The IP Address for the primary control module EMP interface. This address is used for managing the chassis and will continue as the EMP interface address after a takeover. Example values from LibreNMS test devices
| |||||||||||||
| CchasControlEmpIpMask | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.1.1.13 | IpAddress | RW | deprecated | 0.0.0.0 | ||||||||
column · IpAddress · read-write · deprecated This object is deprecated. Instead use alaInterfaceTable(ALCATEL-IND1-IP-MIB) when configuring EMP interfaces. The IP Address Mask for the primary control module EMP interface. This address mask is used for managing the chassis and will continue as the EMP interface mask after a takeover. Example values from LibreNMS test devices
| |||||||||||||
| CchasControlChassisId | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.1.1.14 | Integer32 (0..16) | RW | 0 | |||||||||
column · Integer32 (0..16) · read-write · current The virtual chassis id for the action specified by chasControlVersionMngt when operating in virtual chassis mode. A value of 0 indicates the local chassis. Example values from LibreNMS test devices
| |||||||||||||
| TchasControlRedundantTable | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.2 | NA | |||||||||||
table · not-accessible · current This table contains one row per control module. There is always at least one control module in the system. | |||||||||||||
| RchasControlRedundantEntry | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.2.1 | NA | |||||||||||
row · not-accessible · current Information about a particular control module this table is an extension of the entity physical table but this class is instanciated only for a particular type of physical entity: the control module that has a particular Index. When running in virtual chassis mode, entries are instantiated for the Master and all the slave CMMs
| |||||||||||||
| CchasControlNumberOfTakeover | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.2.1.1 | Counter32 | RO | ||||||||||
column · Counter32 · read-only · current This object is a count of the number of times the control module has changed from primary to secondary mode as a result of a Takeover. Note that this object can be accessed via user interface to either the primary or secondary CMM. The value returned is the number of times that the interfacing control module (either primary or secondary CMM) has changed from primary to secondary mode. This value does not reflect the total number of CMM Takeovers for the switch. To get the total number of Takeovers for the switch, it is necessary to read this value via user interface to each control module independently. | |||||||||||||
| CchasControlDelayedRebootTimer | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.2.1.2 | Unsigned32 (0..31622400) | RW | ||||||||||
column · Unsigned32 (0..31622400) · read-write · current Timer value (in seconds) used to initiate a delayed reboot of the primary or secondary CMM using the certified configuration. Writing this object to a non-zero value results in a CMM reboot following expiration of the specified reset timer delay. Writing this object to zero results in cancellation of a pending CMM delayed reboot. It is now adjusted to wait a maximum of 366 days. | |||||||||||||
| CchasControlDelayedResetAll | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.2.1.3 | Integer32 (-1..65535) | RW | ||||||||||
column · Integer32 (-1..65535) · read-write · current This object is used to schedule a delayed reset all action for a chassis when running in virtual chassis mode. If set to -1 - cancel the timer, 0 - reset all immediately, any other value will start counting down the time until reset. | |||||||||||||
| TchasChassisTable | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.3 | NA | |||||||||||
table · not-accessible · current This table contains one row per chassis. There is always at least one chassis or many when running in virtual chassis mode. | |||||||||||||
| RchasChassisEntry | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.3.1 | NA | |||||||||||
row · not-accessible · current Information about a particular control module this table is an extension of the entity physical table but this class is instanciated only for a particular type of physical entity: the control module that has a particular Index.
| |||||||||||||
| CchasFreeSlots | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.3.1.1 | Unsigned32 (0..18) | RO | 0 | |||||||||
column · Unsigned32 (0..18) · read-only · current The number of free NI front panel slots. Example values from LibreNMS test devices
| |||||||||||||
| CchasPowerLeft | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.3.1.2 | Integer32 (-100000..100000) | RO | 0 | |||||||||
column · Integer32 (-100000..100000) · read-only · current The power still available on the chassis in Watts. Example values from LibreNMS test devices
| |||||||||||||
| CchasNumberOfResets | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.3.1.3 | Counter32 | RO | 16 | |||||||||
| CchasTempRange | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.3.1.4 | INTEGER | RO | 42 | |||||||||
column · INTEGER · read-only · current Temp Range is the value of the temperature sensor for the chassis. The Temp Range value reflects the temperature of the chassis relative to the Temp Threshold value (i.e., over vs. under the threshold).
| |||||||||||||
| CchasTempThreshold | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.3.1.5 | Integer32 (1..150) | RW | 0 | |||||||||
column · Integer32 (1..150) · read-write · current This object is the threshold temperature in degrees Celsius for the chassis. Temp Threshold is the chassis temperature point at which, when reached due to an ascending or descending temperature transition, a temperature notification is provided to the user. When this threshold is exceeded, we start sending traps and other operator notification. | |||||||||||||
| CchasDangerTempThreshold | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.3.1.6 | Integer32 (30..150) | RO | 0 | |||||||||
column · Integer32 (30..150) · read-only · current This Threshold is a second one which is hardcoded. When the Chassis Exceeds this value it starts shutting down NIs. This value will be set by the factory and not changeable. | |||||||||||||
| CchasPrimaryPhysicalIndex | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.3.1.7 | Integer32 (1..255) | RO | 65 | |||||||||
column · Integer32 (1..255) · read-only · current This value holds the Entity Table Physical Index for the Control Module that is currently primary. This is to allow snmp managers to determine which Control Module is currently primary so it knows what entry in the chasControlModuleTable to access for setting the chasControlVersionMngt values for controling the switch. When running in virtual chassis mode, it will contain the Physical Index of the master primary Control Module. Example values from LibreNMS test devices
| |||||||||||||
| CchasCPMAHardwareBoardTemp | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.3.1.8 | Integer32 (0..200) | RO | 42 | |||||||||
column · Integer32 (0..200) · read-only · current This object indicates the current output of the Board Temperature Sensor provided by the LM75 part (degrees Centigrade) for the CPMA control module board. This temperature is what is used for comparing to the threshold and determining whether the value is in range. | |||||||||||||
| CchasCFMAHardwareBoardTemp | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.3.1.9 | Integer32 (0..200) | RO | 0 | |||||||||
column · Integer32 (0..200) · read-only · current This object indicates the current output of the Board Temperature Sensor provided by the LM75 part (degrees Centigrade) for the CFMA fabric board. This temperature is what is used for comparing to the threshold and determining whether the value is in range. Example values from LibreNMS test devices
| |||||||||||||
| CchasCPMBHardwareBoardTemp | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.3.1.10 | Integer32 (0..200) | RO | 0 | |||||||||
column · Integer32 (0..200) · read-only · current This object indicates the current output of the Board Temperature Sensor provided by the LM75 part (degrees Centigrade) for the CPMB control module board. This temperature is what is used for comparing to the threshold and determining whether the value is in range. Example values from LibreNMS test devices
| |||||||||||||
| CchasCFMBHardwareBoardTemp | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.3.1.11 | Integer32 (0..200) | RO | 0 | |||||||||
column · Integer32 (0..200) · read-only · current This object indicates the current output of the Board Temperature Sensor provided by the LM75 part (degrees Centigrade) for the CFMB fabric board. This temperature is what is used for comparing to the threshold and determining whether the value is in range. Example values from LibreNMS test devices
| |||||||||||||
| CchasCFMCHardwareBoardTemp | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.3.1.12 | Integer32 (0..200) | RO | 0 | |||||||||
column · Integer32 (0..200) · read-only · current This object indicates the current output of the Board Temperature Sensor provided by the LM75 part (degrees Centigrade) for the CFMC fabric board. This temperature is what is used for comparing to the threshold and determining whether the value is in range. Example values from LibreNMS test devices
| |||||||||||||
| CchasCFMDHardwareBoardTemp | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.3.1.13 | Integer32 (0..200) | RO | 0 | |||||||||
column · Integer32 (0..200) · read-only · current This object indicates the current output of the Board Temperature Sensor provided by the LM75 part (degrees Centigrade) for the CFMD fabric board. This temperature is what is used for comparing to the threshold and determining whether the value is in range. Example values from LibreNMS test devices
| |||||||||||||
| CchasFTAHardwareBoardTemp | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.3.1.14 | Integer32 (0..200) | RO | 0 | |||||||||
column · Integer32 (0..200) · read-only · current This object indicates the current output of the Board Temperature Sensor provided by the LM75 part (degrees Centigrade) for Fantray 1. This temperature is what is used for comparing to the threshold and determining whether the value is in range. | |||||||||||||
| CchasFTBHardwareBoardTemp | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.3.1.15 | Integer32 (0..200) | RO | 0 | |||||||||
column · Integer32 (0..200) · read-only · current This object indicates the current output of the Board Temperature Sensor provided by the LM75 part (degrees Centigrade) for Fantry 2. This temperature is what is used for comparing to the threshold and determining whether the value is in range. Example values from LibreNMS test devices
| |||||||||||||
| CchasNI1HardwareBoardTemp | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.3.1.16 | Integer32 (0..200) | RO | 42 | |||||||||
column · Integer32 (0..200) · read-only · current This object indicates the current output of the Board Temperature Sensor provided by the LM75 part (degrees Centigrade) for the NI board in slot 1. This temperature is what is used for comparing to the threshold and determining whether the value is in range. | |||||||||||||
| CchasNI2HardwareBoardTemp | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.3.1.17 | Integer32 (0..200) | RO | 0 | |||||||||
column · Integer32 (0..200) · read-only · current This object indicates the current output of the Board Temperature Sensor provided by the LM75 part (degrees Centigrade) for the NI board in slot 2. This temperature is what is used for comparing to the threshold and determining whether the value is in range. Example values from LibreNMS test devices
| |||||||||||||
| CchasNI3HardwareBoardTemp | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.3.1.18 | Integer32 (0..200) | RO | 0 | |||||||||
column · Integer32 (0..200) · read-only · current This object indicates the current output of the Board Temperature Sensor provided by the LM75 part (degrees Centigrade) for the NI board in slot 3. This temperature is what is used for comparing to the threshold and determining whether the value is in range. Example values from LibreNMS test devices
| |||||||||||||
| CchasNI4HardwareBoardTemp | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.3.1.19 | Integer32 (0..200) | RO | 0 | |||||||||
column · Integer32 (0..200) · read-only · current This object indicates the current output of the Board Temperature Sensor provided by the LM75 part (degrees Centigrade) for the NI board in slot 4. This temperature is what is used for comparing to the threshold and determining whether the value is in range. Example values from LibreNMS test devices
| |||||||||||||
| CchasNI5HardwareBoardTemp | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.3.1.20 | Integer32 (0..200) | RO | 0 | |||||||||
column · Integer32 (0..200) · read-only · current This object indicates the current output of the Board Temperature Sensor provided by the LM75 part (degrees Centigrade) for the NI board in slot 5. This temperature is what is used for comparing to the threshold and determining whether the value is in range. Example values from LibreNMS test devices
| |||||||||||||
| CchasNI6HardwareBoardTemp | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.3.1.21 | Integer32 (0..200) | RO | 0 | |||||||||
column · Integer32 (0..200) · read-only · current This object indicates the current output of the Board Temperature Sensor provided by the LM75 part (degrees Centigrade) for the NI board in slot 6. This temperature is what is used for comparing to the threshold and determining whether the value is in range. Example values from LibreNMS test devices
| |||||||||||||
| CchasNI7HardwareBoardTemp | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.3.1.22 | Integer32 (0..200) | RO | 0 | |||||||||
column · Integer32 (0..200) · read-only · current This object indicates the current output of the Board Temperature Sensor provided by the LM75 part (degrees Centigrade) for the NI board in slot 7. This temperature is what is used for comparing to the threshold and determining whether the value is in range. Example values from LibreNMS test devices
| |||||||||||||
| CchasNI8HardwareBoardTemp | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.3.1.23 | Integer32 (0..200) | RO | 0 | |||||||||
column · Integer32 (0..200) · read-only · current This object indicates the current output of the Board Temperature Sensor provided by the LM75 part (degrees Centigrade) for the NI board in slot 8. This temperature is what is used for comparing to the threshold and determining whether the value is in range. Example values from LibreNMS test devices
| |||||||||||||
| CchasPowerSupplyRedundancy | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.3.1.24 | INTEGER | RW | off(2) | |||||||||
column · INTEGER · read-write · current This object indicates the state of power supply redundancy mode. When on(1), N+1 mode redundancy is enabled(default mode). In this mode the system controls the power supplies to maintain efficient use of the power supplies, with 1 extra power supply in case of a power supply failure. Unneeded power supplies are powered off. It can be set to off(2) to disable redundancy mode. In this mode all power supplies are powered on. This object is applicable only to OS10K devices.
Example values from LibreNMS test devices
| |||||||||||||
| CchasPowerSupplyRedundancyReserve | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.3.1.25 | INTEGER | RW | ||||||||||
column · INTEGER · read-write · current When chasPowerSupplyRedundancyReserve is enabled, N+1 power supply redundancy reserve holds the wattage of one power supply in reserve such that the user cannot insert NIs or configure power over Ethernet (POE) that will use the reserved power from that supply. There are two main advantages to enabling chasPowerSupplyRedundancyReserve. The first advantage is that it provides resiliency to avoid POE drawing power from the four main power supplies in the OS9900 chassis to the extent that POE sinks much more wattage than the CMM, CFM, and NI board logic combined. (Note: The power management functions on the OS9900 are complicated by the presence of the controllers on the GNI-P48 boards. Unlike other chassis supporting POE, like OS6860, there is no separate power supply for the POE front-panel ports.) This is not to be confused with chasPowerSupplyRedundancy which switches off unneeded power supplies - on the OS9900, all inserted power supplies are always switched on and enabled. The second advantage of enabling chasPowerSupplyRedundancyReserve is to avoid 'brown-outs'. (A brown-out may happen when a system running at full POE capacity without the N+1 redundancy reserve enabled suffers a power supply failure causing the POE hardware to immediately disable power over Ethernet on the basis of port priority as soon as it detects the failure. Then, if there is still insufficient power available to run the logic and fan trays, the power supplies will 'crowbar' and the system will be power cycled. The software can do little in this scenario since there is insufficient power to keep the CPU chips running. When the system reboots the chassis supervisor will only power-up NI slots based upon the power available from the remaining power supplies.)
| |||||||||||||
| TchasSupervisionRfsLsTable | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.4 | NA | |||||||||||
table · not-accessible · current This table contains a list of file on the remote chassis per directory. | |||||||||||||
| RchasSupervisionRfsLsEntry | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.4.1 | NA | |||||||||||
row · not-accessible · current Information about a remote file. A row in this table contains a file per directory per chassis | |||||||||||||
| CchasSupervisionRfsLsFileIndex | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.4.1.1 | Integer32 (1..100) | RO | ||||||||||
column · Integer32 (1..100) · read-only · current This value holds file Index for the RFS LS table. | |||||||||||||
| CchasSupervisionRfsLsSlot | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.4.1.2 | Unsigned32 | RO | ||||||||||
column · Unsigned32 · read-only · current CMM Slot where remote file is located. | |||||||||||||
| CchasSupervisionRfsLsDirName | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.4.1.3 | SnmpAdminString (SIZE (0..255)) | RO | ||||||||||
column · SnmpAdminString (SIZE (0..255)) · read-only · current The remote directory name where remote file is located in | |||||||||||||
| CchasSupervisionRfsLsFileName | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.4.1.4 | SnmpAdminString (SIZE (0..33)) | RO | ||||||||||
column · SnmpAdminString (SIZE (0..33)) · read-only · current The file name of remote file | |||||||||||||
| CchasSupervisionRfsLsFileType | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.4.1.5 | INTEGER | RO | ||||||||||
column · INTEGER · read-only · current The Type of a remote file
| |||||||||||||
| CchasSupervisionRfsLsFileSize | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.4.1.6 | Unsigned32 | RO | ||||||||||
column · Unsigned32 · read-only · current size of this remote file | |||||||||||||
| CchasSupervisionRfsLsFileAttr | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.4.1.7 | INTEGER | RO | ||||||||||
column · INTEGER · read-only · current attributes of this remote file
| |||||||||||||
| CchasSupervisionRfsLsFileDateTime | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.4.1.8 | SnmpAdminString (SIZE (0..16)) | RO | ||||||||||
column · SnmpAdminString (SIZE (0..16)) · read-only · current the modification date and time of a remote file | |||||||||||||
| NalcatelIND1ChassisSupervisionRfsCommands | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.5 | ||||||||||||
node · current Branch For Chassis Supervision RFS commands. For rrm command the Slot, Command and SrcFileName are mandatory. For rcp command the Slot, Command, SrcFileName and DestFileName are mandatory. For rdf command the Slot and Command are mandatory | |||||||||||||
| SchasSupervisionRfsCommandsSlot | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.5.1 | Unsigned32 | RW | ||||||||||
scalar · Unsigned32 · read-write · current CMM Slot where RFS command should be executed. | |||||||||||||
| SchasSupervisionRfsCommandsCommand | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.5.2 | INTEGER | RW | ||||||||||
scalar · INTEGER · read-write · current This object identifies which of the above Actions is to be
performed. The commands are as follows:
- rrm Remote file remove
- rcp Remote file copy (DEPRECATED please use rget or rput instead)
- rls Remote directory listing
- rdf Remote flash disk space free
- rget Remote file get
- rput Remote file put
| |||||||||||||
| SchasSupervisionRfsCommandsSrcFileName | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.5.3 | SnmpAdminString (SIZE (0..255)) | RW | ||||||||||
scalar · SnmpAdminString (SIZE (0..255)) · read-write · current The remote file for where the RFS action is executed. This includes also the path so directory name and file name. This object is used when command set to rrm or rget or rput. | |||||||||||||
| SchasSupervisionRfsCommandsDestFileName | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.5.4 | SnmpAdminString (SIZE (0..255)) | RW | ||||||||||
scalar · SnmpAdminString (SIZE (0..255)) · read-write · current The destination file for where the RFS action is executed. This includes also the path so directory name and file name. This object is used when command set to rget or rput. | |||||||||||||
| SchasSupervisionRfsCommandsRlsDirName | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.5.5 | SnmpAdminString (SIZE (0..255)) | RW | ||||||||||
scalar · SnmpAdminString (SIZE (0..255)) · read-write · current The remote directory name where remote file is located in. This is used when command set to rls. | |||||||||||||
| SchasSupervisionRfsCommandsRlsFileName | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.5.6 | SnmpAdminString (SIZE (0..255)) | RW | ||||||||||
scalar · SnmpAdminString (SIZE (0..255)) · read-write · current The remote file name where remote file is located in. This is used when command set to rls. | |||||||||||||
| SchasSupervisionRfsCommandsProcessingState | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.5.7 | INTEGER | RO | ||||||||||
scalar · INTEGER · read-only · current command executing state for the previous set operation.
| |||||||||||||
| SchasSupervisionRfsCommandsStatusCode | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.5.8 | INTEGER | RO | ||||||||||
scalar · INTEGER · read-only · current command completetion status error code.
| |||||||||||||
| TchasControlReloadStatusTable | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.6 | NA | |||||||||||
table · not-accessible · current Table containing reload status of each network interface slot or stack module | |||||||||||||
| RchasControlReloadEntry | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.6.1 | NA | |||||||||||
| CchasControlReloadIndex | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.6.1.1 | Integer32 (1..64) | NA | ||||||||||
column · Integer32 (1..64) · not-accessible · current The index (entPhsycialIndex) value of the network interface. | |||||||||||||
| CchasControlReloadStatus | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.6.1.2 | INTEGER | RO | ||||||||||
column · INTEGER · read-only · current Returned value indicates if the network interface module is enabled or disabled for reload.
| |||||||||||||
| NchasGlobalControl | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.7 | ||||||||||||
| SchasGlobalControlDelayedResetAll | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.7.1 | Integer32 (-1..65535) | RW | ||||||||||
scalar · Integer32 (-1..65535) · read-write · current This object is used to schedule a delayed reset all action for a standalone chassis or for the entire virtual chassis when running is virtual chassis mode. To schedule a delayed reset on a specific chassis when running is virtual chassis mode, use the chasControlDelayedResetAll object for the desired chassis. If set to -1 - cancel the timer, 0 - reset all immediately, any other value will start counting down the time until reset. | |||||||||||||
| SchasGlobalControlLongCommand | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.7.2 | INTEGER | RO | ||||||||||
scalar · INTEGER · read-only · current This object is used to indicate whether a long-term action is in progress, and if so, what the action is.
| |||||||||||||
| SchasGlobalControlLongCommandStatus | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.7.3 | INTEGER | RO | ||||||||||
scalar · INTEGER · read-only · current This object indicates the final disposition of the most recent long-term action. When running in virtual chassis mode, the value confirmationRequired(5), indicates that the command identified in chasGlobalControlLongCommand may disrupt the virtual chassis. The command is suspended and requires that chasClobalControlConfirmOperation be set to true, after reviewing the details and accepting the consequences identified by chasGlobalControlConfirmMessage.
| |||||||||||||
| SchasGlobalControlUpdateFirmware | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.7.4 | INTEGER | RW | ||||||||||
scalar · INTEGER · read-write · current This object initiates a firmware update. The chasGlobalControlUpdateSlot and chasGlobalControlUpdateFilename objects must be set prior to setting this object to start the update. The progress of the update can be monitored by reading chasGlobalControlUpdateStatus.
| |||||||||||||
| SchasGlobalControlUpdateSlot | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.7.5 | Integer32 | RW | ||||||||||
scalar · Integer32 · read-write · current This object identifies the slot to be updated. The Slot value is the entPhysicalIndex of the NI or CMM entry in the entPhyscialTable. A value of 0 may be specified to update all NIs or CMMs. The value of 0 is supported only for uboot updates. | |||||||||||||
| SchasGlobalControlUpdateFilename | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.7.6 | SnmpAdminString (SIZE (0..255)) | RW | ||||||||||
scalar · SnmpAdminString (SIZE (0..255)) · read-write · current This object identifies the filename containing the uboot firmware image. | |||||||||||||
| SchasGlobalControlUpdateStatus | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.7.7 | INTEGER | RO | ||||||||||
scalar · INTEGER · read-only · current This object reports the status of the firmware update. The status for the the update identified by chasGlobalControlUpdateFirmware and chasGlobalControlUpdateSlot is returned. When ubootNiAll(4) ubootCmmAll(5) or fpgaCmmAll(10) update is executed, the status of individual NIs or CMMs may be monitored by changing the value of chasGlobalControlUpdateSlot to the desired NI or CMM slot value prior to reading the status. noUpdate(1) - No firmware update has been initiated. updateInProgress(2) - Update is in progress. updateSuccess(3) - The last firmware update was successful. updateFailed(4) - The last firmware update failed.
| |||||||||||||
| SchasGlobalControlConfirmOperation | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.7.8 | TruthValue | RW | ||||||||||
scalar · TruthValue · read-write · current When operating in virtual chassis mode, this object can be set to true(1) to confirm that the operation identified by chasGlobalControlLongCommand can proceed. Set to false(2) to cancel the operation. This should only be used when chasGlobalControlLongCommandStatus is set to confirmationRequired(5), and the value of chasGlobalControlConfirmMessage has been reviewed. | |||||||||||||
| SchasGlobalControlConfirmMessage | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.7.9 | DisplayString | RO | ||||||||||
scalar · DisplayString · read-only · current When operating in virtual chassis mode, this object may be read when chasGlobalControlLongCommandStatus is set to confirmationRequired(5). This will happen when an operation such a reload may disrupt the virtual chassis. This object contains information about the consequences of executing the command identified by chasGlobalControlLongCommand. The command has been suspended. To accept the consequences and proceed with the operation, set chasGlobalControlConfirmOperation to true. | |||||||||||||
| SchasGlobalControlCertifyOnReboot | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.7.10 | INTEGER | RW | ||||||||||
scalar · INTEGER · read-write · current Enable/disable certify on reboot.
| |||||||||||||
| SchasGlobalControlResetToFactory | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.7.11 | INTEGER | RW | ||||||||||
scalar · INTEGER · read-write · current Reset type to factory status to start, schedule or cancel.
| |||||||||||||
| SchasGlobalControlResetToFactoryInTime | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.7.12 | Unsigned32 | RW | ||||||||||
scalar · Unsigned32 · read-write · current Reset to factory time delay in second. | |||||||||||||
| SchasGlobalControlMakePersistent | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.7.13 | INTEGER | RW | ||||||||||
scalar · INTEGER · read-write · current Enable/disable make persistent.
| |||||||||||||
| TchasSupervisionRfsDfTable | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.8 | NA | |||||||||||
table · not-accessible · current This table contains information about file system size and use. | |||||||||||||
| RchasSupervisionRfsDfEntry | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.8.1 | NA | |||||||||||
row · not-accessible · current This entry contains information about file system size and use. | |||||||||||||
| CchasSupervisionRfsDfSlot | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.8.1.1 | Integer32 (1..16) | NA | ||||||||||
column · Integer32 (1..16) · not-accessible · current CMM Slot where flash space is evaluated. | |||||||||||||
| CchasSupervisionRfsDfFlashFree | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.8.1.2 | Unsigned32 | RO | ||||||||||
column · Unsigned32 · read-only · current Number bytes free on the file system. | |||||||||||||
| CchasSupervisionRfsDfFlashSize | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.8.1.3 | Unsigned32 | RO | ||||||||||
column · Unsigned32 · read-only · current Number of total bytes on the file system. | |||||||||||||
| CchasSupervisionRfsDfUsbFree | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.8.1.4 | Unsigned32 | RO | ||||||||||
column · Unsigned32 · read-only · current The amount of free space on the USB file system.
| |||||||||||||
| CchasSupervisionRfsDfUsbSize | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.8.1.5 | Unsigned32 | RO | ||||||||||
column · Unsigned32 · read-only · current The total amount of space on the USB file system.
| |||||||||||||
| TchasSupervisionFlashMemTable | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.9 | NA | |||||||||||
table · not-accessible · current This table contains the systems flash memory information. | |||||||||||||
| RchasSupervisionFlashMemEntry | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.9.1 | NA | |||||||||||
row · not-accessible · current This contains one entry for the flash memory table.
| |||||||||||||
| CchasSupervisionSlot | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.9.1.1 | Integer32 (1..16) | NA | ||||||||||
column · Integer32 (1..16) · not-accessible · current CMM Slot where flash space is evaluated. | |||||||||||||
| CchasSupervisionFlashSize | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.9.1.2 | Unsigned32 | RO | ||||||||||
column · Unsigned32 · read-only · current Flash memory size. | |||||||||||||
| CchasSupervisionFlashFree | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.9.1.3 | Unsigned32 | RO | ||||||||||
column · Unsigned32 · read-only · current Number bytes free on file system. | |||||||||||||
| CchasSupervisionFlashUsed | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.9.1.4 | Integer32 (0..100) | RO | ||||||||||
column · Integer32 (0..100) · read-only · current A rounded up percentage of Flash Memory used. | |||||||||||||
| TchasSupervisionCmmCertifiedTable | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.10 | NA | |||||||||||
table · not-accessible · current This table contains certification status | |||||||||||||
| RchasSupervisionCmmCertifiedEntry | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.10.1 | NA | |||||||||||
row · not-accessible · current Information about control module certification status. This class is instanciated only when running in virtual chassis mode. | |||||||||||||
| CchasSupervisionCmmNum | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.10.1.1 | Integer32 (1..16) | NA | ||||||||||
column · Integer32 (1..16) · not-accessible · current CMM Slot where /certified directory is evaluated. | |||||||||||||
| CchasSupervisionCmmCertifiedStatus | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.10.1.2 | INTEGER | RO | ||||||||||
column · INTEGER · read-only · current The status of the CMM certified directory - certified or not.
| |||||||||||||
| TalaChasEntPhysFanTable | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.11 | NA | |||||||||||
table · not-accessible · current This table contains one row per physical fan entity. | |||||||||||||
| RalaChasEntPhysFanEntry | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.11.1 | NA | |||||||||||
row · not-accessible · current Information about a particular fan in a chassis physical entity. | |||||||||||||
| CalaChasEntPhysFanLocalIndex | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.11.1.1 | Integer32 (1..65535) | NA | ||||||||||
column · Integer32 (1..65535) · not-accessible · current Index to a chassis fan entity | |||||||||||||
| CalaChasEntPhysFanStatus | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.11.1.2 | INTEGER | RO | running(2) | |||||||||
column · INTEGER · read-only · current Chassis fan operational status
Example values from LibreNMS test devices
| |||||||||||||
| CalaChasEntPhysFanAirflow | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.11.1.3 | INTEGER | RO | notApplicable(2) | |||||||||
| CalaChasEntPhysFanSpeed | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.11.1.4 | Unsigned32 | RO | 0 | |||||||||
| NchassisTrapsObj | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.13 | ||||||||||||
| SchassisTrapsStrLevel | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.13.1 | ChassisTrapsStrLevel | RO | ||||||||||
scalar · ChassisTrapsStrLevel · read-only · current An enumerated value which provides the urgency level of the STR. | |||||||||||||
| SchassisTrapsStrAppID | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.13.2 | ChassisTrapsStrAppID | RO | ||||||||||
scalar · ChassisTrapsStrAppID · read-only · current Application Identification number | |||||||||||||
| SchassisTrapsStrSnapID | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.13.3 | ChassisTrapsStrSnapID | RO | ||||||||||
scalar · ChassisTrapsStrSnapID · read-only · current Subapplication Identification number. we can have multiple snapIDs per Subapplication (task) but only one is to be used to send STRs. | |||||||||||||
| SchassisTrapsStrfileName | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.13.4 | SnmpAdminString (SIZE (0..19)) | RO | ||||||||||
scalar · SnmpAdminString (SIZE (0..19)) · read-only · current Name of the source file where the fault was detected. This is given by the C ANSI macro __FILE__. The path shouldn't appear. | |||||||||||||
| SchassisTrapsStrfileLineNb | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.13.5 | ChassisTrapsStrfileLineNb | RO | ||||||||||
scalar · ChassisTrapsStrfileLineNb · read-only · current Line number in the source file where the fault was detected. This is given by the C ANSI macro __LINE__. | |||||||||||||
| SchassisTrapsStrErrorNb | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.13.6 | ChassisTrapsStrErrorNb | RO | ||||||||||
scalar · ChassisTrapsStrErrorNb · read-only · current Fault identificator. The error number identify the kind the detected fault and allow a mapping of the data contained in chassisTrapsdataInfo. | |||||||||||||
| SchassisTrapsStrcomments | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.13.7 | SnmpAdminString (SIZE (0..63)) | RO | ||||||||||
scalar · SnmpAdminString (SIZE (0..63)) · read-only · current comment text explaning the fault. | |||||||||||||
| SchassisTrapsStrdataInfo | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.13.8 | ChassisTrapsStrdataInfo | RO | ||||||||||
scalar · ChassisTrapsStrdataInfo · read-only · current Additional data provided to help to find out the origine of the fault. The contain and the significant portion are varying in accordance with chassisTrapsStrErrorNb. The lenght of this field is expressed in bytes. | |||||||||||||
| SchassisTrapsObjectType | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.13.9 | ChassisTrapsObjectType | RO | ||||||||||
scalar · ChassisTrapsObjectType · read-only · current enumerated value which provide the object type involved in the alert trap. | |||||||||||||
| SchassisTrapsObjectNumber | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.13.10 | ChassisTrapsObjectNumber | RO | ||||||||||
scalar · ChassisTrapsObjectNumber · read-only · current number defining the order of the object in the set. EX: number of the considered fan or power supply. This intend to clarify as much as possible the location of the failure or alert. A instance of the appearance of the trap could be: failure on a module. Power supply 3. | |||||||||||||
| SchassisTrapsAlertNumber | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.13.11 | ChassisTrapsAlertNumber | RO | ||||||||||
scalar · ChassisTrapsAlertNumber · read-only · current this number identify the alert among all the possible chassis alert causes. | |||||||||||||
| SchassisTrapsAlertDescr | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.13.12 | SnmpAdminString (SIZE (0..127)) | RO | ||||||||||
scalar · SnmpAdminString (SIZE (0..127)) · read-only · current description of the alert matching chassisTrapsAlertNumber | |||||||||||||
| SphysicalIndex | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.13.13 | PhysicalIndex | RO | ||||||||||
scalar · PhysicalIndex · read-only · current The Physical index of the involved object. | |||||||||||||
| SchasTrapsNiRqstdBpsSysPower | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.13.14 | Integer32 (0..126) | RO | ||||||||||
scalar · Integer32 (0..126) · read-only · current Requested system power from os-bps | |||||||||||||
| SchasTrapsNiGrantdBpsSysPower | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.13.15 | Integer32 (0..126) | RO | ||||||||||
scalar · Integer32 (0..126) · read-only · current Granted system power from os-bps | |||||||||||||
| SchasTrapBPSShelfId | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.13.16 | Integer32 (1..3) | RO | ||||||||||
scalar · Integer32 (1..3) · read-only · current Granted system power from os-bps | |||||||||||||
| SchasTrapsBPSPowerSupply | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.13.17 | ChasTrapsBPSPowerSupply | RO | ||||||||||
scalar · ChasTrapsBPSPowerSupply · read-only · current value which provide bps power supply involved in the State change trap | |||||||||||||
| SchasTrapsBPSEventAlert | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.13.18 | ChasTrapsBPSEventAlert | RO | ||||||||||
scalar · ChasTrapsBPSEventAlert · read-only · current enumerated value identifying alert | |||||||||||||
| SchasTrapsBPSSystemFETChange | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.13.19 | ChasTrapsBPSFetState | RO | ||||||||||
scalar · ChasTrapsBPSFetState · read-only · current enumerated value which indicate Fet state | |||||||||||||
| SchasTrapsBPSPoeFETChange | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.13.20 | ChasTrapsBPSFetState | RO | ||||||||||
scalar · ChasTrapsBPSFetState · read-only · current enumerated value which indicate Fet state | |||||||||||||
| SchasTrapsBPSFwVersion | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.13.21 | Integer32 (1..99) | RO | ||||||||||
scalar · Integer32 (1..99) · read-only · current enumerated value which indicate the FW that require upgrade | |||||||||||||
| SchasTrapsBPSFwType | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.13.22 | ChasTrapsBPSFwType | RO | ||||||||||
scalar · ChasTrapsBPSFwType · read-only · current value which indicate Fet state | |||||||||||||
| SchassisTrapsWorkingVersion | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.13.23 | SnmpAdminString | RO | ||||||||||
scalar · SnmpAdminString · read-only · current The path to the currently specified working image directory. Value may be /flash/certified or /flash/<working directory name>. | |||||||||||||
| SchassisTrapResetToFactory | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.13.24 | INTEGER | RW | ||||||||||
scalar · INTEGER · read-write · current Reset type to factory status to start, schedule or cancel.
| |||||||||||||
| SchassisTrapResetToFactoryInTime | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.13.25 | Unsigned32 | RW | ||||||||||
scalar · Unsigned32 · read-write · current Reset to factory time delay in second. | |||||||||||||
| SchassisTrapResetToFactoryDescription | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.13.26 | SnmpAdminString | RO | ||||||||||
scalar · SnmpAdminString · read-only · current To provide detail when reset to factory | |||||||||||||
| NalaChasBpsObjects | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14 | ||||||||||||
| TalaChasBpsFwTable | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.1 | NA | deprecated | ||||||||||
table · not-accessible · deprecated This table contains one row per shelf bps firrmware | |||||||||||||
| RalaChasBpsFwEntry | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.1.1 | NA | deprecated | ||||||||||
| CalaChasBpsShelfId | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.1.1.1 | AlaChasBpsShelfId | NA | deprecated | |||||||||
column · AlaChasBpsShelfId · not-accessible · deprecated Bps shelf ID | |||||||||||||
| CalaChasBpsUpdateFirmware | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.1.1.2 | INTEGER | RW | deprecated | |||||||||
column · INTEGER · read-write · deprecated This object is used to start BPS firmware update.
| |||||||||||||
| CalaChasBpsCpldRev | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.1.1.3 | Integer32 (0..100) | RO | deprecated | |||||||||
column · Integer32 (0..100) · read-only · deprecated This object contains the CPLD revision Number of the BPS | |||||||||||||
| CalaChasBpsMmcuRev | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.1.1.4 | Integer32 (0..100) | RO | deprecated | |||||||||
column · Integer32 (0..100) · read-only · deprecated This object contains the MMCU revision Number of the BPS | |||||||||||||
| CalaChasBpsCmcuRev | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.1.1.5 | Integer32 (0..100) | RO | deprecated | |||||||||
column · Integer32 (0..100) · read-only · deprecated This object contains the CMCU revision Number of the BPS | |||||||||||||
| TalaChasBpsConnectorPriorityTable | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.2 | NA | deprecated | ||||||||||
table · not-accessible · deprecated This table contains BPS connector priority for each slot | |||||||||||||
| RalaChasBpsConnectorPriorityEntry | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.2.1 | NA | deprecated | ||||||||||
row · not-accessible · deprecated Information about bps connector priority for each slot
| |||||||||||||
| CalaChasBpsChassisId | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.2.1.1 | Integer32 (1..8) | NA | deprecated | |||||||||
column · Integer32 (1..8) · not-accessible · deprecated Numbers allocated for the stack NIs as follows: - 1..8: valid and assigned slot numbers corresponding to values from the entPhysicalTable | |||||||||||||
| CalaChasBpsConnectorShelfId | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.2.1.2 | AlaChasBpsShelfId | RO | deprecated | |||||||||
column · AlaChasBpsShelfId · read-only · deprecated Bps shelf ID | |||||||||||||
| CalaChasBpsConnectorPriority | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.2.1.3 | Integer32 (0..8) | RW | deprecated | |||||||||
column · Integer32 (0..8) · read-write · deprecated This object specifies the bps connector priority. | |||||||||||||
| CalaChasBpsConnectorNum | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.2.1.4 | Integer32 (0..7) | RO | deprecated | |||||||||
column · Integer32 (0..7) · read-only · deprecated This object specifies the bps connector num. | |||||||||||||
| CalaChasBpsSerialNum | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.2.1.5 | SnmpAdminString (SIZE (0..14)) | RO | deprecated | |||||||||
column · SnmpAdminString (SIZE (0..14)) · read-only · deprecated This object specifies the bps serial num. | |||||||||||||
| TalaChasBpsModeTable | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.3 | NA | |||||||||||
table · not-accessible · current This table contains one row for bps config parameters. | |||||||||||||
| RalaChasBpsModeEntry | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.3.1 | NA | |||||||||||
| CalaChasBpsMode | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.3.1.1 | INTEGER | RW | ||||||||||
column · INTEGER · read-write · current This object is only applicable to BPS .Value is used to specify current Mode of switch.
| |||||||||||||
| TalaChasBpsPowerSupplyTable | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.4 | NA | deprecated | ||||||||||
table · not-accessible · deprecated This table contains BPS power supplies details | |||||||||||||
| RalaChasBpsPowerSupplyEntry | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.4.1 | NA | deprecated | ||||||||||
row · not-accessible · deprecated Information about a particular BPS power supply | |||||||||||||
| CalaChasBpsPowerSupplyShelfId | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.4.1.1 | AlaChasBpsShelfId | NA | deprecated | |||||||||
column · AlaChasBpsShelfId · not-accessible · deprecated BPS shelf ID | |||||||||||||
| CalaChasBpsPowerSupplyIndex | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.4.1.2 | Integer32 (1..6) | NA | deprecated | |||||||||
column · Integer32 (1..6) · not-accessible · deprecated This value hold BPS power power supply Index | |||||||||||||
| CalaChasBpsPowerSupplyName | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.4.1.3 | SnmpAdminString (SIZE (0..63)) | RO | deprecated | |||||||||
column · SnmpAdminString (SIZE (0..63)) · read-only · deprecated This object hold name of BPS power supply | |||||||||||||
| CalaChasBpsPowerSupplyDescr | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.4.1.4 | SnmpAdminString (SIZE (0..63)) | RO | deprecated | |||||||||
column · SnmpAdminString (SIZE (0..63)) · read-only · deprecated This object hold description of BPS power supply | |||||||||||||
| CalaChasBpsPowerSupplyModuleType | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.4.1.5 | SnmpAdminString (SIZE (0..31)) | RO | deprecated | |||||||||
column · SnmpAdminString (SIZE (0..31)) · read-only · deprecated This object is unique module Type or ID from BPS entities eeprom | |||||||||||||
| CalaChasBpsPowerSupplyPartNumber | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.4.1.6 | SnmpAdminString (SIZE (0..16)) | RO | deprecated | |||||||||
column · SnmpAdminString (SIZE (0..16)) · read-only · deprecated This object contains the BPS power supply Part Number | |||||||||||||
| CalaChasBpsPowerSupplyHardwareRev | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.4.1.7 | SnmpAdminString (SIZE (0..8)) | RO | deprecated | |||||||||
column · SnmpAdminString (SIZE (0..8)) · read-only · deprecated The vendor-specific hardware revision string for the BPS power supplies Note that if revision information is stored internally in a non-printable (e.g., binary) format, then the agent must convert such information to a printable format, in an implementation-specific manner. If no specific hardware revision string is associated with the physical component, or this information is unknown to the agent, then this object will contain a zero-length string. | |||||||||||||
| CalaChasBpsPowerSupplySerialNum | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.4.1.8 | SnmpAdminString (SIZE (0..32)) | RO | deprecated | |||||||||
column · SnmpAdminString (SIZE (0..32)) · read-only · deprecated The vendor-specific serial number string for the BPS power supplies | |||||||||||||
| CalaChasBpsPowerSupplyMfgDate | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.4.1.9 | SnmpAdminString (SIZE (0..11)) | RO | deprecated | |||||||||
column · SnmpAdminString (SIZE (0..11)) · read-only · deprecated This object contains the manufacturing date of the BPS power supplies . Its format is mmm dd yyyy : NOV 27 2012. | |||||||||||||
| CalaChasBpsPowerSupplyOperStatus | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.4.1.10 | INTEGER | RO | deprecated | |||||||||
column · INTEGER · read-only · deprecated Oper status of BPS power supply
| |||||||||||||
| CalaChasBpsPowerSupplyPowerProv | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.4.1.11 | Integer32 (0..2000) | RO | deprecated | |||||||||
column · Integer32 (0..2000) · read-only · deprecated It corresponds to max power of BPS power supply. This value is in Watts. | |||||||||||||
| TalaChasBpsTotalPowerAllocTable | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.5 | NA | deprecated | ||||||||||
table · not-accessible · deprecated This table contains one row for parameters which reflect total allocation by BPS . | |||||||||||||
| RalaChasBpsTotalPowerAllocEntry | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.5.1 | NA | deprecated | ||||||||||
row · not-accessible · deprecated Information about various bps config parameters
| |||||||||||||
| CalaChasBpsSysTotalAvailablePower | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.5.1.1 | Integer32 (0..900) | RO | deprecated | |||||||||
column · Integer32 (0..900) · read-only · deprecated This value is only applicable to the BPS Module. It corresponds to system total power available on BPS This value is in Watts. | |||||||||||||
| CalaChasBpsSysTotalAllocation | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.5.1.2 | Integer32 (0..900) | RO | deprecated | |||||||||
column · Integer32 (0..900) · read-only · deprecated This value is only applicable to the BPS Modules. It corresponds to total system power allocated by BPS This value is in Watts. | |||||||||||||
| CalaChasBpsPoeTotalAvailablePower | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.5.1.3 | Integer32 (0..6000) | RO | deprecated | |||||||||
column · Integer32 (0..6000) · read-only · deprecated This value is only applicable to the BPS Modules. It corresponds to system total power available on BPS This value is in Watts. | |||||||||||||
| CalaChasBpsPoeTotalAllocation | 1.3.6.1.4.1.6486.801.1.1.1.3.1.1.14.5.1.4 | Integer32 (0..6000) | RO | deprecated | |||||||||
column · Integer32 (0..6000) · read-only · deprecated This value is only applicable to the Bps Modules. It corresponds to total POE power allocated by BPS This value is in Watts. | |||||||||||||
| NalcatelIND1ChassisMIBConformance | 1.3.6.1.4.1.6486.801.1.1.1.3.1.2 | ||||||||||||
node · current Branch For Chassis Supervision Chassis MIB Subsystem Conformance Information. | |||||||||||||
| NalcatelIND1ChassisMIBGroups | 1.3.6.1.4.1.6486.801.1.1.1.3.1.2.1 | ||||||||||||
node · current Branch For Chassis Supervision Chassis MIB Subsystem Units Of Conformance. | |||||||||||||
| GchasControlModuleGroup | 1.3.6.1.4.1.6486.801.1.1.1.3.1.2.1.1 | ||||||||||||
group · current Chassis Supervision Control Modules Group.
| |||||||||||||
| GchasControlRedundantGroup | 1.3.6.1.4.1.6486.801.1.1.1.3.1.2.1.2 | ||||||||||||
group · current Chassis Supervision Redundant Control Modules Group. | |||||||||||||
| GchasChassisGroup | 1.3.6.1.4.1.6486.801.1.1.1.3.1.2.1.3 | ||||||||||||
group · current Chassis Supervision Chassis Group.
| |||||||||||||
| GchasControlReloadStatusGroup | 1.3.6.1.4.1.6486.801.1.1.1.3.1.2.1.4 | ||||||||||||
group · current Chassis Supervision NI Reload Status Control Modules Group.
| |||||||||||||
| GchasGlobalControlGroup | 1.3.6.1.4.1.6486.801.1.1.1.3.1.2.1.5 | ||||||||||||
group · current Chassis Supervision Global Control Modules Group.
| |||||||||||||
| GchassisNotificationGroup | 1.3.6.1.4.1.6486.801.1.1.1.3.1.2.1.6 | ||||||||||||
group · current Chassis Supervision Notification Group. | |||||||||||||
| GalaChasEntPhysFanGroup | 1.3.6.1.4.1.6486.801.1.1.1.3.1.2.1.7 | ||||||||||||
group · current Chassis Supervision Physical Fan Group. | |||||||||||||
| GalaChasNotificationObjectGroup | 1.3.6.1.4.1.6486.801.1.1.1.3.1.2.1.9 | ||||||||||||
group · current Chassis Supervision Notification Object Group.
| |||||||||||||
| GchassisSupervisionRfsCommandsGroup | 1.3.6.1.4.1.6486.801.1.1.1.3.1.2.1.10 | ||||||||||||
group · current Chassis Supervision RFS Command Group.
| |||||||||||||
| GchasSupervisionCmmCertifiedEntryGroup | 1.3.6.1.4.1.6486.801.1.1.1.3.1.2.1.11 | ||||||||||||
| GchasSupervisionFlashMemEntryGroup | 1.3.6.1.4.1.6486.801.1.1.1.3.1.2.1.12 | ||||||||||||
group · current The systems flash memory information group. | |||||||||||||
| GchasSupervisionRfsDfEntryGroup | 1.3.6.1.4.1.6486.801.1.1.1.3.1.2.1.13 | ||||||||||||
group · current Information about RfsDf file system group. | |||||||||||||
| GchasSupervisionRfsLsEntryGroup | 1.3.6.1.4.1.6486.801.1.1.1.3.1.2.1.14 | ||||||||||||
group · current Information about a RfsLs file group. | |||||||||||||
| GalaChasBpsFwGroup | 1.3.6.1.4.1.6486.801.1.1.1.3.1.2.1.15 | ||||||||||||
group · current Information about BPS FW group. | |||||||||||||
| GalaChasBpsConnectorPriorityGroup | 1.3.6.1.4.1.6486.801.1.1.1.3.1.2.1.16 | ||||||||||||
group · current Information about BPS Connector Priority group. | |||||||||||||
| GalaChasBpsModeGroup | 1.3.6.1.4.1.6486.801.1.1.1.3.1.2.1.17 | ||||||||||||
| GalaChasBpsPowerSupplyGroup | 1.3.6.1.4.1.6486.801.1.1.1.3.1.2.1.18 | ||||||||||||
group · current BPS Power Supply group. | |||||||||||||
| GalaChasBpsTotalPowerAllocGroup | 1.3.6.1.4.1.6486.801.1.1.1.3.1.2.1.19 | ||||||||||||
group · current BPS Total Power Alloc group. | |||||||||||||
| NalcatelIND1ChassisMIBCompliances | 1.3.6.1.4.1.6486.801.1.1.1.3.1.2.2 | ||||||||||||
node · current Branch For Chassis Supervision Chassis MIB Subsystem Compliance Statements. | |||||||||||||
| MalcatelIND1ChassisMIBCompliance | 1.3.6.1.4.1.6486.801.1.1.1.3.1.2.2.1 | ||||||||||||
compliance · current Compliance statement for Chassis Supervision.
| |||||||||||||
Textual conventions
AlaChasBpsShelfIdInteger32 (1..3)BPS shelf Id .
ChasEntPhysLedINTEGERamberBlink(5)amberOn(4)greenBlink(3)greenOn(2)notApplicable(0)off(1)Textual convention for physical LEDs. Note: Due to European regulation, the LEDs will never be illuminated in red, but will be either green or amber.
ChasTrapsBPSEventAlertINTEGERbpsModeChanged(3)bpsPsPlugged(1)bpsPsUnPlugged(2)notApplicable(4)Textual convention for BPS event alert
ChasTrapsBPSFetStateINTEGERnotApplicable(3)off(2)on(1)Textual convention for BPS FET state
ChasTrapsBPSFwTypeINTEGERbpsFwCmcu(1)bpsFwCpld(3)bpsFwMmcu(2)notApplicable(4)Textual convention for BPS FW upgrade requirment alert
ChasTrapsBPSPowerSupplyINTEGERbpsPoePower1(3)bpsPoePower2(4)bpsPoePower3(5)bpsSysPower1(1)bpsSysPower2(2)notApplicable(6)Textual convention for type of bps power supply.
ChassisTrapsAlertNumberINTEGERactivateScheduled(44)activateStarted(45)airflowReverse(58)c20NiFailed(57)c20RestoreFailed(56)c20RestoreOk(55)c20UpgradeFailed(54)c20UpgradeOk(53)certifyCompleted(5)certifyFailed(6)certifyFlashSyncStarted(4)certifyStarted(3)cfmDown(65)cmmAPlugged(33)cmmAUnPlugged(35)cmmBPlugged(34)cmmBUnPlugged(36)cmmDown(63)cmmStartingAsPrimary(30)cmmStartingAsSecondary(31)cmmStartupCompleted(32)fanFailed(18)fanOk(19)fansOk(20)getAfileCompleted(46)getAfileFailed(47)imageFileChecksumChanged(62)lowNvramBattery(37)macAllocFailed(16)macRangeFailed(17)niDown(64)notEnoughFabricsOperational(38)powerMissing(24)psAllOperational(27)psNotOperational(25)psOperational(26)redundancyDisabledCertifyNeeded(29)redundancyNotSupported(28)reloadInProgress(52)restoreCompleted(11)restoreFailed(12)restoreStarted(10)runningCertified(2)runningWorking(1)secAutoActivate(40)secAutoCertifyCompleted(42)secAutoCertifyStarted(41)secInactiveReset(43)simplexNoSynchro(39)synchroCompleted(8)synchroFailed(9)synchroStarted(7)sysUpdateEnd(51)sysUpdateError(50)sysUpdateInProgress(49)sysUpdateStart(48)takeoverCompleted(15)takeoverDeferred(14)takeoverStarted(13)tempDanger(61)tempHWHigh(60)tempOverDangerThreshold(23)tempOverThreshold(21)tempSWHigh(59)tempUnderThreshold(22)this number identify the alert among all the possible chassis alert causes.
ChassisTrapsObjectNumberInteger32 (0..255)A number defining the order of the object in the set. EX: The number of the considered fan or power supply. This intend to clarify as much as possible the location of the failure or alert. An instance of the appearance of the trap could be: failure on a module. Power supply 3.
ChassisTrapsObjectTypeINTEGERchassis(1)cmm(5)fabric(6)fan(4)gbic(7)ni(2)powerSuply(3)temperature(8)An enumerated value which provides the object type involved in the alert trap.
ChassisTrapsStrAppIDInteger32 (0..255)Application Identification number
ChassisTrapsStrErrorNbInteger32 (0..65535)Fault identifier. The error number identifies the kind the detected fault and allows a mapping of the data contained in chassisTrapsdataInfo.
ChassisTrapsStrLevelINTEGERstrApplicationFatal(2)strFatal(3)strNotFatal(1)enumerated value which provide the urgency level of the STR.
ChassisTrapsStrSnapIDInteger32 (0..255)Subapplication Identification number. we can have multiple snapIDs per Subapplication (task) but only one is to be used to send STRs.
ChassisTrapsStrdataInfoOCTET STRING (SIZE (0..63))Additional data provided to help to find out the origine of the fault. The contain and the significant portion are varying in accordance with chassisTrapsStrErrorNb. The lenght of this field is expressed in bytes.
ChassisTrapsStrfileLineNbInteger32 (1..65535)Line number in the source file where the fault was detected. This is given by the C ANSI macro __LINE__.
Traps / Notifications
- chasTrapsBPSFwUpgradeAlert
1.3.6.1.4.1.6486.801.1.1.1.3.1.0.7 - chasTrapsBPSLessAllocSysPwr
1.3.6.1.4.1.6486.801.1.1.1.3.1.0.4 - chasTrapsBPSStateChange
1.3.6.1.4.1.6486.801.1.1.1.3.1.0.5 - chasTrapsNiBPSFETStateChange
1.3.6.1.4.1.6486.801.1.1.1.3.1.0.6 - chassisTrapsAlert
1.3.6.1.4.1.6486.801.1.1.1.3.1.0.2 - chassisTrapsImageSigCheckFailed
1.3.6.1.4.1.6486.801.1.1.1.3.1.0.8 - chassisTrapsResetToFactory
1.3.6.1.4.1.6486.801.1.1.1.3.1.0.9 - chassisTrapsStateChange
1.3.6.1.4.1.6486.801.1.1.1.3.1.0.3 - chassisTrapsStr
1.3.6.1.4.1.6486.801.1.1.1.3.1.0.1
Groups and compliance
- alaChasBpsConnectorPriorityGroup
- alaChasBpsFwGroup
- alaChasBpsModeGroup
- alaChasBpsPowerSupplyGroup
- alaChasBpsTotalPowerAllocGroup
- alaChasEntPhysFanGroup
- alaChasNotificationObjectGroup
- alcatelIND1ChassisMIBCompliance
- alcatelIND1ChassisPhysMIBCompliance
- chasChassisGroup
- chasControlModuleGroup
- chasControlRedundantGroup
- chasControlReloadStatusGroup
- chasEntPhysicalGroup
- chasGlobalControlGroup
- chasSupervisionCmmCertifiedEntryGroup
- chasSupervisionFlashMemEntryGroup
- chasSupervisionRfsDfEntryGroup
- chasSupervisionRfsLsEntryGroup
- chassisNotificationGroup
- chassisPhysNotificationGroup
- chassisSupervisionRfsCommandsGroup
- chassisTemperatureGroup