ALCATEL-IND1-IPSEC-MIB
Alcatel-Lucent EnterpriseThis module describes an authoritative enterprise-specific Simple
Network Management Protocol (SNMP) Management Information Base (MIB):
Proprietary IPsec MIB definitions
The right to make changes in specification and other information
contained in this document without prior notice is reserved.
No liability shall be assumed for any incidental, indirect, special,
or consequential damages whatsoever arising from or related to this
document or the information contained herein.
Vendors, end-users, and other interested parties are granted
non-exclusive license to use this specification in connection with
management of the products for which it is intended to be used.
Copyright (C) ALE USA Inc. 2014-2019
Copyright (C) 1995-2013 Alcatel-Lucent
ALL RIGHTS RESERVED WORLDWIDEsnmptranslate -m ALCATEL-IND1-IPSEC-MIB -Tpsnmpwalk -v2c -c <community> -m ALCATEL-IND1-IPSEC-MIB <host> 1.3.6.1.4.1.6486.800.1.2.1.43.1Imports
| ALCATEL-IND1-BASE | softentIND1IPsec |
|---|---|
| INET-ADDRESS-MIB | InetAddress, InetAddressType |
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP |
| SNMPv2-SMI | Bits, Counter32, Integer32, IpAddress, MODULE-IDENTITY, MibIdentifier, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, iso |
| SNMPv2-TC | DisplayString, PhysAddress, RowStatus, TEXTUAL-CONVENTION, TruthValue |
OID tree
| Name | OID | Type | Access | Status |
|---|---|---|---|---|
| IalcatelIND1IPsecMIB | 1.3.6.1.4.1.6486.800.1.2.1.43.1 | |||
identity This module describes an authoritative enterprise-specific Simple
Network Management Protocol (SNMP) Management Information Base (MIB):
Proprietary IPsec MIB definitions
The right to make changes in specification and other information
contained in this document without prior notice is reserved.
No liability shall be assumed for any incidental, indirect, special,
or consequential damages whatsoever arising from or related to this
document or the information contained herein.
Vendors, end-users, and other interested parties are granted
non-exclusive license to use this specification in connection with
management of the products for which it is intended to be used.
Copyright (C) ALE USA Inc. 2014-2019
Copyright (C) 1995-2013 Alcatel-Lucent
ALL RIGHTS RESERVED WORLDWIDE | ||||
| NalcatelIND1IPsecMIBObjects | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1 | |||
| NalaIPsecConfig | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.1 | |||
| TalaIPsecSecurityKeyTable | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.1.1 | NA | ||
table · not-accessible · current Table allowing the configuration of the switch's IPsec security key. The security key is used to encrypt and IPsec related information retained in permanent storage. There is always a single row in this table with an index value of 1. | ||||
| RalaIPsecSecurityKeyEntry | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.1.1.1 | NA | ||
| CalaIPsecSecurityKeyID | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.1.1.1.1 | Unsigned32 | NA | |
column · Unsigned32 · not-accessible · current The row's identifier. Only one entry is ever present, with an ID value of 1. | ||||
| CalaIPsecSecurityKeyCurrent | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.1.1.1.2 | OCTET STRING (SIZE (16)) | RW | |
column · OCTET STRING (SIZE (16)) · read-write · current The current value of the IPsec security key. If an attempt is made to read the value of this object, a zero-length octet string will be returned. | ||||
| CalaIPsecSecurityKeyNew | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.1.1.1.3 | OCTET STRING (SIZE (16)) | RW | |
column · OCTET STRING (SIZE (16)) · read-write · current Used to set a new value for the IPsec security key. Both alaIPsecSecurityKeyCurrent (with its correct value) and alaIPsecSecurityKeyNew must be specified in the same SNMP SET message. If alaIPsecSecurityKeyCurrent is not present, or if its value is incorrect, the attempt to set a new key will fail. | ||||
| TalaIPsecStatisticsTable | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.1.2 | NA | ||
table · not-accessible · current Table allowing the IPv6 statistics to be retrieved. | ||||
| RalaIPsecStatisticsEntry | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.1.2.1 | NA | ||
| CalaIPsecStatisticsProtocol | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.1.2.1.1 | INTEGER | NA | |
column · INTEGER · not-accessible · current IP protocol version covered by the IPsec statistics.
| ||||
| CalaIPsecStatisticsInSuccessful | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.1.2.1.2 | Counter32 | RO | |
column · Counter32 · read-only · current Number of incoming packets requiring IPsec processing that were successfully handled. | ||||
| CalaIPsecStatisticsInPolicyViolation | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.1.2.1.3 | Counter32 | RO | |
column · Counter32 · read-only · current Number of incoming packets that were dropped because of policy violations. | ||||
| CalaIPsecStatisticsInNoSA | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.1.2.1.4 | Counter32 | RO | |
column · Counter32 · read-only · current Number of incoming packets dropped because no matching SA was found. | ||||
| CalaIPsecStatisticsInUnknownSPI | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.1.2.1.5 | Counter32 | RO | |
column · Counter32 · read-only · current Number of incoming packets dropped because the SPI was unknown. | ||||
| CalaIPsecStatisticsInAHReplay | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.1.2.1.6 | Counter32 | RO | |
column · Counter32 · read-only · current Number of incoming packets that failed the AH replay check. | ||||
| CalaIPsecStatisticsInESPReplay | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.1.2.1.7 | Counter32 | RO | |
column · Counter32 · read-only · current Number of incoming packets taht failed the ESP replay check. | ||||
| CalaIPsecStatisticsInAHAuthenticationSuccess | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.1.2.1.8 | Counter32 | RO | |
column · Counter32 · read-only · current Number of incoming packets that successfully passed AH authentication. | ||||
| CalaIPsecStatisticsInAHAuthenticationFail | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.1.2.1.9 | Counter32 | RO | |
column · Counter32 · read-only · current Number of incoming packets that failed AH authentication. | ||||
| CalaIPsecStatisticsInESPAuthenticationSuccess | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.1.2.1.10 | Counter32 | RO | |
column · Counter32 · read-only · current Number of incoming packets that successfully passed ESP authentication. | ||||
| CalaIPsecStatisticsInESPAuthenticationFail | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.1.2.1.11 | Counter32 | RO | |
column · Counter32 · read-only · current Number of incoming packets that failed ESP authentication. | ||||
| CalaIPsecStatisticsInBadPacket | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.1.2.1.12 | Counter32 | RO | |
column · Counter32 · read-only · current Number of incoming packets requiring IPsec processing that were not valid. | ||||
| CalaIPsecStatisticsInNoMemory | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.1.2.1.13 | Counter32 | RO | |
column · Counter32 · read-only · current Number of incoming IPsec packets dropped because no memory was available. | ||||
| CalaIPsecStatisticsOutSuccessful | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.1.2.1.14 | Counter32 | RO | |
column · Counter32 · read-only · current Number of outgoing packets requiring IPsec processing that were successfully handled. | ||||
| CalaIPsecStatisticsOutPolicyViolation | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.1.2.1.15 | Counter32 | RO | |
column · Counter32 · read-only · current Number of outgoing packets dropped because of a policy violation. | ||||
| CalaIPsecStatisticsOutNoSA | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.1.2.1.16 | Counter32 | RO | |
column · Counter32 · read-only · current Number of outgoing packets dropped because no matching SA was found. | ||||
| CalaIPsecStatisticsOutBadPacket | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.1.2.1.17 | Counter32 | RO | |
column · Counter32 · read-only · current Number of outgoing packets requiring IPsec processing that were not valid. | ||||
| CalaIPsecStatisticsOutNoMemory | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.1.2.1.18 | Counter32 | RO | |
column · Counter32 · read-only · current Number of outgoing IPsec packets dropped because no memory was available. | ||||
| CalaIPsecStatisticsInDiscarded | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.1.2.1.19 | Counter32 | RO | |
column · Counter32 · read-only · current Number of incoming packets dropped because they matched a discard policy. | ||||
| CalaIPsecStatisticsOutDiscarded | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.1.2.1.20 | Counter32 | RO | |
column · Counter32 · read-only · current Number of outgoing packets dropped because they matched a discard policy. | ||||
| TalaIPsecSecurityPolicyTable | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.2 | NA | ||
table · not-accessible · current Table allowing the configuration of IPsec security policies. | ||||
| RalaIPsecSecurityPolicyEntry | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.2.1 | NA | ||
| CalaIPsecSecurityPolicyID | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.2.1.1 | Unsigned32 | NA | |
column · Unsigned32 · not-accessible · current A unique identifier for this security policy. When creating a new policy, a zero value must be specified. An available policy ID will then be automatically assigned to the policy. | ||||
| CalaIPsecSecurityPolicySourceType | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.2.1.2 | InetAddressType | RC | |
column · InetAddressType · read-create · current The type of source address specified. | ||||
| CalaIPsecSecurityPolicySource | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.2.1.3 | InetAddress | RC | |
column · InetAddress · read-create · current The source of packets covered by this policy. | ||||
| CalaIPsecSecurityPolicySourcePrefixLength | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.2.1.4 | IPsecPrefixLength | RC | |
column · IPsecPrefixLength · read-create · current The number of bits of the source address used to determine
which packets are covered by this policy.
The default value varies depending upon the type of
source address specified:
IPv4 - 32
IPv6 - 128
DNS name - 0 (any other value is ignored) | ||||
| CalaIPsecSecurityPolicySourcePort | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.2.1.5 | IPsecPortNumber | RC | |
column · IPsecPortNumber · read-create · current The source port of packets covered by this policy. To match packets from any port, specify the 0 wildcard value. A wildcard policy will only be used when there is no exact match to a destination port in another entry. | ||||
| CalaIPsecSecurityPolicyDestinationType | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.2.1.6 | InetAddressType | RC | |
column · InetAddressType · read-create · current The type of destination address specified. | ||||
| CalaIPsecSecurityPolicyDestination | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.2.1.7 | InetAddress | RC | |
column · InetAddress · read-create · current The destination of packets covered by this policy. | ||||
| CalaIPsecSecurityPolicyDestinationPrefixLength | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.2.1.8 | IPsecPrefixLength | RC | |
column · IPsecPrefixLength · read-create · current The number of bits of the destination prefix used to determine
which packets are covered by this policy.
The default value varies depending upon the type of
destination address specified:
IPv4 - 32
IPv6 - 128
DNS name - 0 (any other value is ignored) | ||||
| CalaIPsecSecurityPolicyDestinationPort | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.2.1.9 | IPsecPortNumber | RC | |
column · IPsecPortNumber · read-create · current The destination port of packets covered by this policy. To match packets from any port, specify the 0 wildcard value. A wildcard policy will only be used when there is no exact match to a destination port in another entry. | ||||
| CalaIPsecSecurityPolicyULProtocol | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.2.1.10 | IPsecULProtocol | RC | |
column · IPsecULProtocol · read-create · current The upper-layer protocol of packets covered by this policy. To match all protocols, specify the 255 wildcard value. A wildcard policy will only be used when there is no exact match to the protocol value specified in another entry. | ||||
| CalaIPsecSecurityPolicyICMPv6Type | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.2.1.11 | INTEGER (0..255) | RC | |
column · INTEGER (0..255) · read-create · current If the upper-layer protocol is ICMPv6, an ICMPv6 type value may be specified to restrict the policy to a specific packet type. To match all ICMPv6 packets, the 0 wildcard value should be specified. | ||||
| CalaIPsecSecurityPolicyDirection | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.2.1.12 | INTEGER | RC | |
column · INTEGER · read-create · current The direction of traffic covered by this policy.
| ||||
| CalaIPsecSecurityPolicyName | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.2.1.13 | IPsecName | RC | |
column · IPsecName · read-create · current A name for this policy. | ||||
| CalaIPsecSecurityPolicyDescription | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.2.1.14 | IPsecDescription | RC | |
column · IPsecDescription · read-create · current A detailed description of this policy. | ||||
| CalaIPsecSecurityPolicyAction | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.2.1.15 | INTEGER | RC | |
column · INTEGER · read-create · current The action to take on traffic covered by this policy. discard(0) means that all traffic covered by the policy will be discarded. ipsec(2) means that IPsec processing will take place on the traffic. One or more rules should be defined in the IPsec Rule Table. If no rules are defined processing is identical to none(0) being specified.
| ||||
| CalaIPsecSecurityPolicyAdminState | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.2.1.16 | IPsecAdminState | RC | |
column · IPsecAdminState · read-create · current Allows a policy to be administratively enabled or disabled. | ||||
| CalaIPsecSecurityPolicyOperationalState | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.2.1.17 | IPsecOperationalState | RO | |
column · IPsecOperationalState · read-only · current The operational state of this policy. | ||||
| CalaIPsecSecurityPolicyPriority | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.2.1.18 | INTEGER (1..1000) | RC | |
column · INTEGER (1..1000) · read-create · current The priority for this policy. When traffic would be covered by multiple policies the policy with the highest priority value is used. If two policies have the same priority, the one configured first has precedence. | ||||
| CalaIPsecSecurityPolicyRowStatus | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.2.1.19 | RowStatus | RC | |
column · RowStatus · read-create · current Used to control the addition and removal of security policy entries. | ||||
| TalaIPsecSecurityPolicyRuleTable | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.3 | NA | ||
table · not-accessible · current Table allowing the configuration of the IPsec rules for a security policy. | ||||
| RalaIPsecSecurityPolicyRuleEntry | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.3.1 | NA | ||
row · not-accessible · current A security policy entry. | ||||
| CalaIPsecSecurityPolicyRuleIndex | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.3.1.1 | Unsigned32 (1..10) | NA | |
column · Unsigned32 (1..10) · not-accessible · current Index specifying the order in which multiple rules for the same security policy will be applied. Rules are indexed by the order in which they are applied to the original payload. For example, for a security policy where an IPv6 payload should be protected by an ESP header, which should be protected by an AH header, there would be two Rule Table entries. The ESP entry would have an index of 1 (first rule applied to the payload). The AH entry would have an index of 2 (second rule applied). | ||||
| CalaIPsecSecurityPolicyRuleProtocol | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.3.1.2 | INTEGER | RC | |
column · INTEGER · read-create · current Indicates the type of header required by the rule.
| ||||
| CalaIPsecSecurityPolicyRuleMode | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.3.1.3 | INTEGER | RC | |
column · INTEGER · read-create · current The mode in which the rule's protocol is running. At present, only transport(1) is allowed. Until tunnel mode is supported, transport(1) will be treated as the default value.
| ||||
| CalaIPsecSecurityPolicyRuleRowStatus | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.3.1.4 | RowStatus | RC | |
column · RowStatus · read-create · current Used to control the addition and removal of security policy IPsec rule entries. | ||||
| TalaIPsecSAConfigTable | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.4 | NA | ||
table · not-accessible · current Table allowing the manual configuration of Security Associations in the Security Association Database (SAD). | ||||
| RalaIPsecSAConfigEntry | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.4.1 | NA | ||
row · not-accessible · current Manually configured security association (SA) parameters.
| ||||
| CalaIPsecSAConfigID | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.4.1.1 | Unsigned32 | NA | |
column · Unsigned32 · not-accessible · current A unique identifier for this manually configured SA. When creating a new SA, a zero value must be specified. An available ID will then be automatically assigned to the SA. | ||||
| CalaIPsecSAConfigType | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.4.1.2 | IPsecSAType | RC | |
column · IPsecSAType · read-create · current The type of this SA: AH or ESP. Once set, the type may not be changed. | ||||
| CalaIPsecSAConfigSourceType | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.4.1.3 | InetAddressType | RC | |
column · InetAddressType · read-create · current The type of source address specified. | ||||
| CalaIPsecSAConfigSource | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.4.1.4 | InetAddress | RC | |
column · InetAddress · read-create · current The source of packets covered by this SA. | ||||
| CalaIPsecSAConfigDestinationType | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.4.1.5 | InetAddressType | RC | |
column · InetAddressType · read-create · current The type of destination address specified. | ||||
| CalaIPsecSAConfigDestination | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.4.1.6 | InetAddress | RC | |
column · InetAddress · read-create · current The destination of packets covered by this SA. | ||||
| CalaIPsecSAConfigSPI | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.4.1.7 | Unsigned32 | RC | |
column · Unsigned32 · read-create · current The Security Parameters Index (SPI) of this SA. | ||||
| CalaIPsecSAConfigName | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.4.1.8 | IPsecName | RC | |
column · IPsecName · read-create · current The name of this manually configured SA. | ||||
| CalaIPsecSAConfigDescription | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.4.1.9 | IPsecDescription | RC | |
column · IPsecDescription · read-create · current A detailed description for the manually created IPsec SA. | ||||
| CalaIPsecSAConfigEncryptionAlgorithm | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.4.1.10 | IPsecESPAlgorithm | RC | |
column · IPsecESPAlgorithm · read-create · current For an ESP SA, defines the encryption algorithm to be used. none(0) should be specified if ESP is being used for integrity only. If null(11) is specified, alaIPsecSAConfigAuthenticationAlgorithm may not be none(0). The value of this object is none(0) for AH SAs. | ||||
| CalaIPsecSAConfigEncryptionKeyLength | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.4.1.11 | Unsigned32 | RC | |
column · Unsigned32 · read-create · current For those algorithms where multiple key lengths are supported, specifies the key length to be used. Zero may be specified to use the default key length.
| ||||
| CalaIPsecSAConfigAuthenticationAlgorithm | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.4.1.12 | IPsecAHAlgorithm | RC | |
column · IPsecAHAlgorithm · read-create · current Defines the authentication algorithm to be used. For ESP SAs, none(0) may be specified for encryption-only ESP. For ESP integrity-only, ESP integrity and encryption, or for AH SAs, hmacmd5(2), hmacsha1(3), or aesxcbcmac(9) must be specified. | ||||
| CalaIPsecSAConfigAdminState | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.4.1.13 | IPsecAdminState | RC | |
column · IPsecAdminState · read-create · current Allows a manually configured SA to be administratively enabled or disabled. | ||||
| CalaIPsecSAConfigOperationalState | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.4.1.14 | IPsecOperationalState | RO | |
column · IPsecOperationalState · read-only · current The operational state of the manually configured SA. | ||||
| CalaIPsecSAConfigRowStatus | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.4.1.15 | RowStatus | RC | |
column · RowStatus · read-create · current Used to control the addition and removal of manually configured IPsec SAs. | ||||
| TalaIPsecKeyTable | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.5 | NA | ||
table · not-accessible · current Table used to configure the keys used by manually configured Security Associations in the IPsec Security Association Configuration table. | ||||
| RalaIPsecKeyEntry | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.5.1 | NA | ||
row · not-accessible · current An IPsec key. Keys in the table must be uniquely identified by the combination of key type and key name. However, since the key name can be up to 255 characters, beyond the 128-element size limit for SNMP index objects, the key ID is used to uniquely identify a key for SNMP access.
| ||||
| CalaIPsecKeyID | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.5.1.1 | Unsigned32 | NA | |
column · Unsigned32 · not-accessible · current A unique identifier for this key. When creating a new key, a zero value must be specified. An available ID will then be automatically assigned to the key. | ||||
| CalaIPsecKeyType | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.5.1.2 | INTEGER | RC | |
column · INTEGER · read-create · current Indicates if the key is to be used for encryption or authentication by a SA. Once a key is created, its type may not be changed.
| ||||
| CalaIPsecKeyName | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.5.1.3 | OCTET STRING (SIZE (1..255)) | RC | |
column · OCTET STRING (SIZE (1..255)) · read-create · current The name of the key. For manually-configured SA keys, the name is limited to a maximum length of 20 characters and should correspond to an entry in the alaIPsecSAConfigTable. The key name may not be changed once a key is created. | ||||
| CalaIPsecKey | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.5.1.4 | OCTET STRING | RC | |
column · OCTET STRING · read-create · current The key value. The value specified must match the required key length for the algorithm using the key. If an attempt is made to read the value of this object a zero-length octet string will be returned. | ||||
| CalaIPsecKeyEncrypted | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.5.1.5 | TruthValue | RC | |
column · TruthValue · read-create · current If true, the key value is specified in AOS encrypted form. For example, keys being restored from the configuration file. | ||||
| CalaIPsecKeyRowStatus | 1.3.6.1.4.1.6486.800.1.2.1.43.1.1.5.1.6 | RowStatus | RC | |
column · RowStatus · read-create · current Used to control the addition and removal of keys. | ||||
| NalcatelIND1IPsecMIBConformance | 1.3.6.1.4.1.6486.800.1.2.1.43.1.2 | |||
| NalcatelIND1IPsecMIBCompliances | 1.3.6.1.4.1.6486.800.1.2.1.43.1.2.1 | |||
| MalaIPsecCompliance | 1.3.6.1.4.1.6486.800.1.2.1.43.1.2.1.1 | |||
compliance · current The compliance statement for Alcatel switches implementing ALCATEL-IND1-IPSEC-MIB. | ||||
| NalcatelIND1IPsecMIBGroups | 1.3.6.1.4.1.6486.800.1.2.1.43.1.2.2 | |||
| GalaIPsecConfigGroup | 1.3.6.1.4.1.6486.800.1.2.1.43.1.2.2.1 | |||
group · current A collection of objects to support global configuration of IPsec.
| ||||
| GalaIPsecSecurityPolicyGroup | 1.3.6.1.4.1.6486.800.1.2.1.43.1.2.2.2 | |||
group · current A collection of objects to support management of IPsec security policies.
| ||||
| GalaIPsecSAConfigGroup | 1.3.6.1.4.1.6486.800.1.2.1.43.1.2.2.3 | |||
group · current A collection of objects to support management of manually configured IPsec SAs.
| ||||
| GalaIPsecKeyGroup | 1.3.6.1.4.1.6486.800.1.2.1.43.1.2.2.4 | |||
group · current A collection of objects to support management of keys. | ||||
Textual conventions
IPsecAHAlgorithmINTEGERaesxcbcmac(9)hmacmd5(2)hmacsha1(3)none(0)AH algorithms.
IPsecAdminStateINTEGERdisabled(2)enabled(1)Administrative state.
IPsecDescriptionOCTET STRING (SIZE (0..200))Display hint:
200aOptional description of a table entry.
IPsecESPAlgorithmINTEGERaescbc(12)aesctr(13)des3cbc(3)descbc(2)none(0)null(11)ESP algorithms.
IPsecNameDisplayString (SIZE (1..20))Display hint:
255aThe name of a table entry.
IPsecOperationalStateINTEGERdisabled(2)dnspending(3)enabled(1)Operational state. enabled(1) - The entry is enabled. disabled(2) - The entry is administratively disabled or DNS resolution has experienced a permanent failure. dnspending(3) - Awaiting DNS resolution before making the entry active.
IPsecPortNumberINTEGER (0..65535)A port number value. 0 is the wildcard value to match any port.
IPsecPrefixLengthINTEGER (0..128)Significant bits in an IPv6 address prefix. 0..32 is the valid range for IPv4 addresses. 0..128 is valid for IPv6 addresses
IPsecSATypeINTEGERah(2)esp(3)SA type.
IPsecULProtocolINTEGER (0..255)An upper-layer protocol number. 255 is the wildcard value to match any protocol.