INOVONICS-MODEL640-MIB
Inovonics, Inc.The MIB for the Model 640 AARON FM Rebroadcast Receiver.
snmptranslate -m INOVONICS-MODEL640-MIB -Tpsnmpwalk -v2c -c <community> -m INOVONICS-MODEL640-MIB <host> 1.3.6.1.4.1.42111.640Imports
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP |
|---|---|
| SNMPv2-SMI | Bits, Integer32, IpAddress, MODULE-IDENTITY, MibIdentifier, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, enterprises, iso |
| SNMPv2-TC | DisplayString, PhysAddress, TEXTUAL-CONVENTION |
OID tree
| Name | OID | Type | Access | Status | Example | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| NinovonicsBroadcast | 1.3.6.1.4.1.42111 | ||||||||||||
| Imodel640 | 1.3.6.1.4.1.42111.640 | ||||||||||||
identity The MIB for the Model 640 AARON FM Rebroadcast Receiver. | |||||||||||||
| Ntraps | 1.3.6.1.4.1.42111.640.1 | ||||||||||||
| Nnotifications | 1.3.6.1.4.1.42111.640.1.0 | ||||||||||||
| !audioLossTrap | 1.3.6.1.4.1.42111.640.1.0.1 | ||||||||||||
notification · current This trap occurs when the Audio Loss alarm is triggered on OR off. The status of the alarm is included as a variable binding in the form of the audioLossAlarm object.
| |||||||||||||
| !lowSignalTrap | 1.3.6.1.4.1.42111.640.1.0.2 | ||||||||||||
notification · current This trap occurs when the Low Signal alarm is triggered on OR off. The status of the alarm is included as a variable binding in the form of the lowSignalAlarm object.
| |||||||||||||
| !rdsErrorTrap | 1.3.6.1.4.1.42111.640.1.0.3 | ||||||||||||
notification · current This trap occurs when the RDS Error/Mismatch alarm is triggered on OR off. The status of the alarm is included as a variable binding in the form of the rdsErrorAlarm object.
| |||||||||||||
| !pilotLossTrap | 1.3.6.1.4.1.42111.640.1.0.4 | ||||||||||||
notification · current This trap occurs when the Pilot Loss alarm is triggered on OR off. The status of the alarm is included as a variable binding in the form of the pilotLossAlarm object.
| |||||||||||||
| Nproduct | 1.3.6.1.4.1.42111.640.2 | ||||||||||||
| Sserial | 1.3.6.1.4.1.42111.640.2.1 | DisplayString | RO | 239 | |||||||||
| Sversion | 1.3.6.1.4.1.42111.640.2.2 | DisplayString | RO | 1.2.0.14 | |||||||||
| Sdate | 1.3.6.1.4.1.42111.640.2.3 | DisplayString | RO | ||||||||||
scalar · DisplayString · read-only · current Date of firmware version. | |||||||||||||
| NnowPlaying | 1.3.6.1.4.1.42111.640.3 | ||||||||||||
| Sfrequency | 1.3.6.1.4.1.42111.640.3.1 | Integer32 (6500..10800) | RW | 8990 | |||||||||
scalar · Integer32 (6500..10800) · read-write · current Currently tuned frequency, in 10kHz steps. Can be set between 6500 and 10800. Example values from LibreNMS test devices
| |||||||||||||
| ScurrentPreset | 1.3.6.1.4.1.42111.640.3.2 | Integer32 (1..10) | RW | ||||||||||
scalar · Integer32 (1..10) · read-write · current Currently selected preset. The preset can also be set to 1-10. A value of 0 means a preset is not selected. | |||||||||||||
| Srssi | 1.3.6.1.4.1.42111.640.3.3 | Integer32 (0..120) | RO | 51 | |||||||||
| Sbandwidth | 1.3.6.1.4.1.42111.640.3.4 | Integer32 | RO | ||||||||||
scalar · Integer32 · read-only · current IF Bandwidth (units: kHz). | |||||||||||||
| Smultipath | 1.3.6.1.4.1.42111.640.3.5 | Integer32 (0..100) | RO | 2 | |||||||||
scalar · Integer32 (0..100) · read-only · current Amount of Multipath. The Range is 0-100%. Example values from LibreNMS test devices
| |||||||||||||
| Snoise | 1.3.6.1.4.1.42111.640.3.6 | Integer32 (0..100) | RO | ||||||||||
scalar · Integer32 (0..100) · read-only · current Amount of Ultrasonic Noise. The Range is 0-100%. | |||||||||||||
| SleftLeveldB | 1.3.6.1.4.1.42111.640.3.7 | Integer32 (-128..6) | RO | ||||||||||
scalar · Integer32 (-128..6) · read-only · current Left channel level (units: dB). | |||||||||||||
| SrightLeveldB | 1.3.6.1.4.1.42111.640.3.8 | Integer32 (-128..6) | RO | ||||||||||
scalar · Integer32 (-128..6) · read-only · current Right channel level (units: dB). | |||||||||||||
| SleftPlusRightLeveldB | 1.3.6.1.4.1.42111.640.3.9 | Integer32 (-128..6) | RO | ||||||||||
scalar · Integer32 (-128..6) · read-only · current Left+Right level (units: dB). | |||||||||||||
| SleftMinusRightLeveldB | 1.3.6.1.4.1.42111.640.3.10 | Integer32 (-128..6) | RO | ||||||||||
scalar · Integer32 (-128..6) · read-only · current Left-Right level (units: dB). | |||||||||||||
| NreceptionTools | 1.3.6.1.4.1.42111.640.4 | ||||||||||||
| NbandwidthIF | 1.3.6.1.4.1.42111.640.4.1 | ||||||||||||
| SbandwidthMode | 1.3.6.1.4.1.42111.640.4.1.1 | INTEGER | RW | ||||||||||
scalar · INTEGER · read-write · current IF Bandwidth Mode - set to automatically adjust IF bandwidth, or used a fixed bandwidth set by the fixedBandwidth OID.
| |||||||||||||
| SfixedBandwidth | 1.3.6.1.4.1.42111.640.4.1.2 | INTEGER | RW | ||||||||||
scalar · INTEGER · read-write · current IF Bandwidth used when the mode is set to fixed.
| |||||||||||||
| NstereoBlend | 1.3.6.1.4.1.42111.640.4.2 | ||||||||||||
| SstereoBlendAmount | 1.3.6.1.4.1.42111.640.4.2.1 | Integer32 (0..100) | RO | ||||||||||
scalar · Integer32 (0..100) · read-only · current Amount of stereo blend processing applied (Units: %). | |||||||||||||
| SstereoBlendAuto | 1.3.6.1.4.1.42111.640.4.2.2 | OnOff | RW | ||||||||||
scalar · OnOff · read-write · current If set to auto, the blend processing is handled automatically. the other stereo blend settings are not used. | |||||||||||||
| SstereoBlendUseRSSI | 1.3.6.1.4.1.42111.640.4.2.3 | OnOff | RW | ||||||||||
scalar · OnOff · read-write · current Set ON to use RSSI as a metric for blend processing. | |||||||||||||
| SstereoBlendThresholdRSSI | 1.3.6.1.4.1.42111.640.4.2.4 | Integer32 (30..60) | RW | ||||||||||
scalar · Integer32 (30..60) · read-write · current As the RSSI drops below this set value, more blending will occur (Units: dBuV). | |||||||||||||
| SstereoBlendUseUSN | 1.3.6.1.4.1.42111.640.4.2.5 | OnOff | RW | ||||||||||
scalar · OnOff · read-write · current Set ON to use USN as a metric for blend processing. | |||||||||||||
| SstereoBlendThresholdUSN | 1.3.6.1.4.1.42111.640.4.2.6 | Integer32 (0..50) | RW | ||||||||||
scalar · Integer32 (0..50) · read-write · current As the USN goes above this set value, more blending will occur (Units: %). | |||||||||||||
| SstereoBlendUseMultipath | 1.3.6.1.4.1.42111.640.4.2.7 | OnOff | RW | ||||||||||
scalar · OnOff · read-write · current Set ON to use multipath as a metric for blend processing. | |||||||||||||
| SstereoBlendThresholdMultipath | 1.3.6.1.4.1.42111.640.4.2.8 | Integer32 (0..50) | RW | ||||||||||
scalar · Integer32 (0..50) · read-write · current As the multipath goes above this set value, more blending will occur (Units: %). | |||||||||||||
| NhighBlend | 1.3.6.1.4.1.42111.640.4.3 | ||||||||||||
| ShighBlendAmount | 1.3.6.1.4.1.42111.640.4.3.1 | Integer32 (0..100) | RO | ||||||||||
scalar · Integer32 (0..100) · read-only · current Amount of stereo blend processing applied (Units: %). | |||||||||||||
| ShighBlendAuto | 1.3.6.1.4.1.42111.640.4.3.2 | OnOff | RW | ||||||||||
scalar · OnOff · read-write · current If set to auto, the high blend processing is handled automatically. the other high blend settings are not used. | |||||||||||||
| ShighBlendUseRSSI | 1.3.6.1.4.1.42111.640.4.3.3 | OnOff | RW | ||||||||||
scalar · OnOff · read-write · current Set ON to use RSSI as a metric for high blend processing. | |||||||||||||
| ShighBlendThresholdRSSI | 1.3.6.1.4.1.42111.640.4.3.4 | Integer32 (30..60) | RW | ||||||||||
scalar · Integer32 (30..60) · read-write · current As the RSSI drops below this set value, more high blending will occur (Units: dBuV). | |||||||||||||
| ShighBlendUseUSN | 1.3.6.1.4.1.42111.640.4.3.5 | OnOff | RW | ||||||||||
scalar · OnOff · read-write · current Set ON to use USN as a metric for high blend processing. | |||||||||||||
| ShighBlendThresholdUSN | 1.3.6.1.4.1.42111.640.4.3.6 | Integer32 (0..50) | RW | ||||||||||
scalar · Integer32 (0..50) · read-write · current As the USN goes above this set value, more high blending will occur (Units: %). | |||||||||||||
| ShighBlendUseMultipath | 1.3.6.1.4.1.42111.640.4.3.7 | OnOff | RW | ||||||||||
scalar · OnOff · read-write · current Set ON to use multipath as a metric for high blend processing. | |||||||||||||
| ShighBlendThresholdMultipath | 1.3.6.1.4.1.42111.640.4.3.8 | Integer32 (0..50) | RW | ||||||||||
scalar · Integer32 (0..50) · read-write · current As the multipath goes above this set value, more high blending will occur (Units: %). | |||||||||||||
| NbandBlend | 1.3.6.1.4.1.42111.640.4.4 | ||||||||||||
| SbandBlendEnable | 1.3.6.1.4.1.42111.640.4.4.1 | OnOff | RW | ||||||||||
scalar · OnOff · read-write · current Enable or disable 4 band blend processing. | |||||||||||||
| SbandBlendControl | 1.3.6.1.4.1.42111.640.4.4.2 | Integer32 (50..150) | RW | ||||||||||
scalar · Integer32 (50..150) · read-write · current Controls the agressiveness of the 4 band blend. | |||||||||||||
| SbandBlendLF | 1.3.6.1.4.1.42111.640.4.4.3 | Integer32 (0..100) | RO | ||||||||||
scalar · Integer32 (0..100) · read-only · current The amount of blending in the Low Frequency band (Units: %). | |||||||||||||
| SbandBlend2k | 1.3.6.1.4.1.42111.640.4.4.4 | Integer32 (0..100) | RO | ||||||||||
scalar · Integer32 (0..100) · read-only · current The amount of blending in the 2kHz band (Units: %). | |||||||||||||
| SbandBlend5k | 1.3.6.1.4.1.42111.640.4.4.5 | Integer32 (0..100) | RO | ||||||||||
scalar · Integer32 (0..100) · read-only · current The amount of blending in the 5kHz band (Units: %). | |||||||||||||
| SbandBlendHF | 1.3.6.1.4.1.42111.640.4.4.6 | Integer32 (0..100) | RO | ||||||||||
scalar · Integer32 (0..100) · read-only · current The amount of blending in the High Frequency band (Units: %). | |||||||||||||
| Nhighcut | 1.3.6.1.4.1.42111.640.4.5 | ||||||||||||
| ShighcutAmount | 1.3.6.1.4.1.42111.640.4.5.1 | Integer32 (0..100) | RO | ||||||||||
scalar · Integer32 (0..100) · read-only · current Amount of highcut processing applied (Units: %). | |||||||||||||
| ShighcutAuto | 1.3.6.1.4.1.42111.640.4.5.2 | OnOff | RW | ||||||||||
scalar · OnOff · read-write · current If set to auto, the highcut processing is handled automatically. the other high blend settings are not used. | |||||||||||||
| ShighcutUseRSSI | 1.3.6.1.4.1.42111.640.4.5.3 | OnOff | RW | ||||||||||
scalar · OnOff · read-write · current Set ON to use RSSI as a metric for highcut processing. | |||||||||||||
| ShighcutThresholdRSSI | 1.3.6.1.4.1.42111.640.4.5.4 | Integer32 (30..60) | RW | ||||||||||
scalar · Integer32 (30..60) · read-write · current As the RSSI drops below this set value, more highcut will occur (Units: dBuV). | |||||||||||||
| ShighcutUseUSN | 1.3.6.1.4.1.42111.640.4.5.5 | OnOff | RW | ||||||||||
scalar · OnOff · read-write · current Set ON to use USN as a metric for highcut processing. | |||||||||||||
| ShighcutThresholdUSN | 1.3.6.1.4.1.42111.640.4.5.6 | Integer32 (0..50) | RW | ||||||||||
scalar · Integer32 (0..50) · read-write · current As the USN goes above this set value, more highcut will occur (Units: %). | |||||||||||||
| ShighcutUseMultipath | 1.3.6.1.4.1.42111.640.4.5.7 | OnOff | RW | ||||||||||
scalar · OnOff · read-write · current Set ON to use multipath as a metric for highcut processing. | |||||||||||||
| ShighcutThresholdMultipath | 1.3.6.1.4.1.42111.640.4.5.8 | Integer32 (0..50) | RW | ||||||||||
scalar · Integer32 (0..50) · read-write · current As the multipath goes above this set value, more highcut will occur (Units: %). | |||||||||||||
| SmonoStereo | 1.3.6.1.4.1.42111.640.4.6 | INTEGER | RW | ||||||||||
scalar · INTEGER · read-write · current Set to forced mono or stereo (auto).
| |||||||||||||
| SmultipathSuppression | 1.3.6.1.4.1.42111.640.4.7 | OnOff | RW | ||||||||||
scalar · OnOff · read-write · current Controls the use of Multipath Suppression processing. | |||||||||||||
| SchannelEqualizer | 1.3.6.1.4.1.42111.640.4.8 | OnOff | RW | ||||||||||
scalar · OnOff · read-write · current Controls the use of the Channel Equalizer. | |||||||||||||
| Nrds | 1.3.6.1.4.1.42111.640.5 | ||||||||||||
| Spi | 1.3.6.1.4.1.42111.640.5.1 | DisplayString | RO | ||||||||||
scalar · DisplayString · read-only · current PI (Program Identification) Code. | |||||||||||||
| Scall | 1.3.6.1.4.1.42111.640.5.2 | DisplayString | RO | ||||||||||
scalar · DisplayString · read-only · current Callsign/Call Letters for the received PI Code. | |||||||||||||
| Sps | 1.3.6.1.4.1.42111.640.5.3 | DisplayString | RO | ||||||||||
scalar · DisplayString · read-only · current PS (Program Service). | |||||||||||||
| Srt | 1.3.6.1.4.1.42111.640.5.4 | DisplayString | RO | ||||||||||
scalar · DisplayString · read-only · current RT (Radio Text). | |||||||||||||
| Spty | 1.3.6.1.4.1.42111.640.5.5 | DisplayString | RO | ||||||||||
scalar · DisplayString · read-only · current PTY (Program Type). | |||||||||||||
| Sptyn | 1.3.6.1.4.1.42111.640.5.6 | DisplayString | RO | ||||||||||
scalar · DisplayString · read-only · current PTYN (Program Type Name). | |||||||||||||
| SrdsTime | 1.3.6.1.4.1.42111.640.5.7 | DisplayString | RO | ||||||||||
scalar · DisplayString · read-only · current RDS time received. | |||||||||||||
| Sms | 1.3.6.1.4.1.42111.640.5.8 | INTEGER | RO | ||||||||||
scalar · INTEGER · read-only · current Music/Speech flag.
| |||||||||||||
| Sdi | 1.3.6.1.4.1.42111.640.5.9 | INTEGER | RO | ||||||||||
scalar · INTEGER · read-only · current Mono/Stereo flag.
| |||||||||||||
| Stp | 1.3.6.1.4.1.42111.640.5.10 | INTEGER | RO | ||||||||||
scalar · INTEGER · read-only · current Traffic Programming flag.
| |||||||||||||
| Sta | 1.3.6.1.4.1.42111.640.5.11 | OnOff | RO | ||||||||||
scalar · OnOff · read-only · current Traffic Alert flag. | |||||||||||||
| Nalarms | 1.3.6.1.4.1.42111.640.6 | ||||||||||||
| NalarmStatus | 1.3.6.1.4.1.42111.640.6.1 | ||||||||||||
| SaudioLossAlarm | 1.3.6.1.4.1.42111.640.6.1.1 | OnOff | RO | 0 | |||||||||
scalar · OnOff · read-only · current Status of the Audio Loss alarm. Example values from LibreNMS test devices
| |||||||||||||
| SlowSignalAlarm | 1.3.6.1.4.1.42111.640.6.1.2 | OnOff | RO | 0 | |||||||||
scalar · OnOff · read-only · current Status of the Low Signal alarm. Example values from LibreNMS test devices
| |||||||||||||
| SrdsErrorAlarm | 1.3.6.1.4.1.42111.640.6.1.3 | OnOff | RO | 0 | |||||||||
scalar · OnOff · read-only · current Status of the RDS Error/Mismatch alarm. Example values from LibreNMS test devices
| |||||||||||||
| SpilotLossAlarm | 1.3.6.1.4.1.42111.640.6.1.4 | OnOff | RO | 0 | |||||||||
scalar · OnOff · read-only · current Status of the Pilot Loss alarm. Example values from LibreNMS test devices
| |||||||||||||
| NaudioLoss | 1.3.6.1.4.1.42111.640.6.2 | ||||||||||||
| SaudioLossEnable | 1.3.6.1.4.1.42111.640.6.2.1 | OnOff | RW | ||||||||||
scalar · OnOff · read-write · current Enable the Audio Loss alarm. | |||||||||||||
| SaudioLossThreshOn | 1.3.6.1.4.1.42111.640.6.2.2 | Integer32 (-40..0) | RW | ||||||||||
scalar · Integer32 (-40..0) · read-write · current Threshold for alarm turning on (units: dB). | |||||||||||||
| SaudioLossThreshOff | 1.3.6.1.4.1.42111.640.6.2.3 | Integer32 (-40..0) | RW | ||||||||||
scalar · Integer32 (-40..0) · read-write · current Threshold for alarm turning off (units: dB). | |||||||||||||
| SaudioLossTimeOn | 1.3.6.1.4.1.42111.640.6.2.4 | Integer32 (1..120) | RW | ||||||||||
scalar · Integer32 (1..120) · read-write · current Amount of time the audio level must be below the Threshold On value before the alarm turns on (units: seconds). | |||||||||||||
| SaudioLossTimeOff | 1.3.6.1.4.1.42111.640.6.2.5 | Integer32 (1..120) | RW | ||||||||||
scalar · Integer32 (1..120) · read-write · current Amount of time the audio level must be above the Threshold On value before the alarm turns on (units: seconds). | |||||||||||||
| NlowSignal | 1.3.6.1.4.1.42111.640.6.3 | ||||||||||||
| SlowSignalEnable | 1.3.6.1.4.1.42111.640.6.3.1 | OnOff | RW | ||||||||||
scalar · OnOff · read-write · current Enable the Low Signal alarm. | |||||||||||||
| SlowSignalMute | 1.3.6.1.4.1.42111.640.6.3.2 | OnOff | RW | ||||||||||
scalar · OnOff · read-write · current If enabled, radio will mute when Low Signal alarm is on. | |||||||||||||
| SlowSignalThreshOn | 1.3.6.1.4.1.42111.640.6.3.3 | Integer32 (0..80) | RW | ||||||||||
scalar · Integer32 (0..80) · read-write · current Threshold for alarm turning on (units: dBuV). | |||||||||||||
| SlowSignalThreshOff | 1.3.6.1.4.1.42111.640.6.3.4 | Integer32 (0..80) | RW | ||||||||||
scalar · Integer32 (0..80) · read-write · current Threshold for alarm turning off (units: dBuV). | |||||||||||||
| SlowSignalTimeOn | 1.3.6.1.4.1.42111.640.6.3.5 | Integer32 (1..120) | RW | ||||||||||
scalar · Integer32 (1..120) · read-write · current Amount of time the RSSI level must be below the Threshold On value before the alarm turns on (units: seconds). | |||||||||||||
| SlowSignalTimeOff | 1.3.6.1.4.1.42111.640.6.3.6 | Integer32 (1..120) | RW | ||||||||||
scalar · Integer32 (1..120) · read-write · current Amount of time the RSSI level must be above the Threshold Off value before the alarm turns off (units: seconds). | |||||||||||||
| NrdsLoss | 1.3.6.1.4.1.42111.640.6.4 | ||||||||||||
| SrdsLossEnable | 1.3.6.1.4.1.42111.640.6.4.1 | OnOff | RW | ||||||||||
scalar · OnOff · read-write · current Enable the RDS Error alarm. | |||||||||||||
| SrdsPIErrorEnable | 1.3.6.1.4.1.42111.640.6.4.2 | OnOff | RW | ||||||||||
scalar · OnOff · read-write · current If enabled, the alarm will occur if RDS is present but the received PI does not match that set in rdsPICode. | |||||||||||||
| SrdsPICode | 1.3.6.1.4.1.42111.640.6.4.3 | DisplayString (SIZE (4)) | RW | ||||||||||
scalar · DisplayString (SIZE (4)) · read-write · current Set PI Code to compare with received PI. | |||||||||||||
| SrdsLossTimeOn | 1.3.6.1.4.1.42111.640.6.4.4 | Integer32 (1..120) | RW | ||||||||||
scalar · Integer32 (1..120) · read-write · current Amount of time the RDS must be gone/PI Code incorrect before the alarm turns on (units: seconds). | |||||||||||||
| SrdsLossTimeOff | 1.3.6.1.4.1.42111.640.6.4.5 | Integer32 (1..120) | RW | ||||||||||
scalar · Integer32 (1..120) · read-write · current Amount of time the RDS must be present/PI Code correct before the alarm turns off (units: seconds). | |||||||||||||
| NpilotLoss | 1.3.6.1.4.1.42111.640.6.5 | ||||||||||||
| SpilotLossEnable | 1.3.6.1.4.1.42111.640.6.5.1 | OnOff | RW | ||||||||||
scalar · OnOff · read-write · current Enable the Pilot Loss alarm. | |||||||||||||
| SpilotLossTimeOn | 1.3.6.1.4.1.42111.640.6.5.2 | Integer32 (1..120) | RW | ||||||||||
scalar · Integer32 (1..120) · read-write · current Amount of time the pilot must be gone before the alarm turns on (units: seconds). | |||||||||||||
| SpilotLossTimeOff | 1.3.6.1.4.1.42111.640.6.5.3 | Integer32 (1..120) | RW | ||||||||||
scalar · Integer32 (1..120) · read-write · current Amount of time the pilot must be present before the alarm turns off (units: seconds). | |||||||||||||
| Nsetup | 1.3.6.1.4.1.42111.640.7 | ||||||||||||
| Noutputs | 1.3.6.1.4.1.42111.640.7.1 | ||||||||||||
| SanalogLevel | 1.3.6.1.4.1.42111.640.7.1.1 | Integer32 (-200..180) | RW | ||||||||||
scalar · Integer32 (-200..180) · read-write · current Analog Output level (Units: 0.1dB, Ex. -100 = -10.0dB). | |||||||||||||
| SanalogDeemphasis | 1.3.6.1.4.1.42111.640.7.1.2 | OnOff | RW | ||||||||||
scalar · OnOff · read-write · current De-emphasis applied to analog outputs. | |||||||||||||
| SdigitalLevel | 1.3.6.1.4.1.42111.640.7.1.3 | Integer32 (-300..0) | RW | ||||||||||
scalar · Integer32 (-300..0) · read-write · current Digital Output level (Units: 0.1dB, Ex. -200 = -20.0dB). | |||||||||||||
| SdigitalDeemphasis | 1.3.6.1.4.1.42111.640.7.1.4 | OnOff | RW | ||||||||||
scalar · OnOff · read-write · current De-emphasis applied to AES output. | |||||||||||||
| SmpxLevel | 1.3.6.1.4.1.42111.640.7.1.5 | Integer32 (1000..6000) | RW | ||||||||||
scalar · Integer32 (1000..6000) · read-write · current MPX Output level (Units: mVpp, Ex. 3100 = 3.10Vpp). Though the units are mVpp, the resolution is less than 1mVpp. When this value is set, it will round to the closest possible value. | |||||||||||||
| SmpxClipping | 1.3.6.1.4.1.42111.640.7.1.6 | Integer32 (-20..30) | RW | ||||||||||
scalar · Integer32 (-20..30) · read-write · current MPX Clipping amount (Units: 0.1dB, Ex. 16 = 1.6dB. This can be set in 0.2dB steps. | |||||||||||||
| Nnetwork | 1.3.6.1.4.1.42111.640.7.2 | ||||||||||||
| Sdhcp | 1.3.6.1.4.1.42111.640.7.2.1 | INTEGER | RW | ||||||||||
scalar · INTEGER · read-write · current DHCP enabled, or disabled (static IP).
| |||||||||||||
| Sip | 1.3.6.1.4.1.42111.640.7.2.2 | IpAddress | RW | ||||||||||
scalar · IpAddress · read-write · current Device IP Address. | |||||||||||||
| Sgateway | 1.3.6.1.4.1.42111.640.7.2.3 | IpAddress | RW | ||||||||||
scalar · IpAddress · read-write · current Gateway IP Address. | |||||||||||||
| Ssubnet | 1.3.6.1.4.1.42111.640.7.2.4 | IpAddress | RW | ||||||||||
scalar · IpAddress · read-write · current Device subnet mask. | |||||||||||||
| Sdns | 1.3.6.1.4.1.42111.640.7.2.5 | IpAddress | RW | ||||||||||
scalar · IpAddress · read-write · current Device DNS address. | |||||||||||||
| ShttpPort | 1.3.6.1.4.1.42111.640.7.2.6 | Integer32 (1..65535) | RW | ||||||||||
scalar · Integer32 (1..65535) · read-write · current HTTP port for webserver. | |||||||||||||
| Shostname | 1.3.6.1.4.1.42111.640.7.2.7 | DisplayString (SIZE (0..16)) | RW | ||||||||||
scalar · DisplayString (SIZE (0..16)) · read-write · current NBNS hostname. | |||||||||||||
| Smac | 1.3.6.1.4.1.42111.640.7.2.8 | DisplayString | RO | ||||||||||
scalar · DisplayString · read-only · current MAC address of this device. | |||||||||||||
| NdynDNS | 1.3.6.1.4.1.42111.640.7.3 | ||||||||||||
| SddnsMode | 1.3.6.1.4.1.42111.640.7.3.1 | INTEGER | RW | ||||||||||
scalar · INTEGER · read-write · current Dynamic DNS provider/mode.
| |||||||||||||
| SddnsHostname | 1.3.6.1.4.1.42111.640.7.3.2 | DisplayString (SIZE (1..63)) | RW | ||||||||||
scalar · DisplayString (SIZE (1..63)) · read-write · current Your DDNS hostname (proper web addess). | |||||||||||||
| SddnsUsername | 1.3.6.1.4.1.42111.640.7.3.3 | DisplayString (SIZE (1..63)) | RW | ||||||||||
scalar · DisplayString (SIZE (1..63)) · read-write · current The username for your DDNS account. | |||||||||||||
| SddnsPassword | 1.3.6.1.4.1.42111.640.7.3.4 | DisplayString (SIZE (1..63)) | RW | ||||||||||
scalar · DisplayString (SIZE (1..63)) · read-write · current The password for your DDNS account. | |||||||||||||
| SddnsStatus | 1.3.6.1.4.1.42111.640.7.3.5 | DisplayString | RO | ||||||||||
scalar · DisplayString · read-only · current The status of the DDNS service. | |||||||||||||
| Ntime | 1.3.6.1.4.1.42111.640.7.4 | ||||||||||||
| Stimezone | 1.3.6.1.4.1.42111.640.7.4.1 | Integer32 (-120..140) | RW | ||||||||||
scalar · Integer32 (-120..140) · read-write · current UTC offset (Units: 0.1hours). EX: -80 = UTC-8.0. Can be set in 0.5 hour increments. | |||||||||||||
| Sdst | 1.3.6.1.4.1.42111.640.7.4.2 | OnOff | RW | ||||||||||
scalar · OnOff · read-write · current Whether Daylight Saving Time is currently in effect. | |||||||||||||
| Sautodst | 1.3.6.1.4.1.42111.640.7.4.3 | OnOff | RW | ||||||||||
scalar · OnOff · read-write · current Enable to automatically follow US Daylight Saving Time. | |||||||||||||
| StimeServer | 1.3.6.1.4.1.42111.640.7.4.4 | DisplayString (SIZE (0..63)) | RW | ||||||||||
scalar · DisplayString (SIZE (0..63)) · read-write · current URL for a custom NTP time server. | |||||||||||||
| Nsnmp | 1.3.6.1.4.1.42111.640.7.5 | ||||||||||||
| SsnmpMode | 1.3.6.1.4.1.42111.640.7.5.1 | INTEGER | RW | ||||||||||
scalar · INTEGER · read-write · current SNMP mode. Restrict SNMP read or write.
| |||||||||||||
| SsnmpReadCommunity | 1.3.6.1.4.1.42111.640.7.5.2 | DisplayString (SIZE (0..31)) | RW | ||||||||||
scalar · DisplayString (SIZE (0..31)) · read-write · current SNMP read community string for read access. | |||||||||||||
| SsnmpWriteCommunity | 1.3.6.1.4.1.42111.640.7.5.3 | DisplayString (SIZE (0..31)) | RW | ||||||||||
scalar · DisplayString (SIZE (0..31)) · read-write · current SNMP write community string for write access. | |||||||||||||
| SsnmpPort | 1.3.6.1.4.1.42111.640.7.5.4 | Integer32 (1..65535) | RW | ||||||||||
scalar · Integer32 (1..65535) · read-write · current UDP port for SNMP communication. SNMP standard is UDP port 161. | |||||||||||||
| SsnmpTrapsPort | 1.3.6.1.4.1.42111.640.7.5.5 | Integer32 (1..65535) | RW | ||||||||||
scalar · Integer32 (1..65535) · read-write · current UDP port for SNMP traps. SNMP standard is UDP port 162. | |||||||||||||
| SsnmpTrapDestination1 | 1.3.6.1.4.1.42111.640.7.5.6 | IpAddress | RW | ||||||||||
scalar · IpAddress · read-write · current IP address 1 to send traps to. | |||||||||||||
| SsnmpTrapDestination2 | 1.3.6.1.4.1.42111.640.7.5.7 | IpAddress | RW | ||||||||||
scalar · IpAddress · read-write · current IP address 2 to send traps to. | |||||||||||||
| SsnmpTrapDestination3 | 1.3.6.1.4.1.42111.640.7.5.8 | IpAddress | RW | ||||||||||
scalar · IpAddress · read-write · current IP address 3 to send traps to. | |||||||||||||
| Nemail | 1.3.6.1.4.1.42111.640.7.6 | ||||||||||||
| SsmtpServer | 1.3.6.1.4.1.42111.640.7.6.1 | DisplayString (SIZE (0..63)) | RW | ||||||||||
scalar · DisplayString (SIZE (0..63)) · read-write · current URL or IP of SMTP server. | |||||||||||||
| SsmtpPort | 1.3.6.1.4.1.42111.640.7.6.2 | Integer32 (1..65535) | RW | ||||||||||
scalar · Integer32 (1..65535) · read-write · current TCP port for SMTP (depends on server). | |||||||||||||
| Sssl | 1.3.6.1.4.1.42111.640.7.6.3 | OnOff | RW | ||||||||||
scalar · OnOff · read-write · current Enable/disable SSL security for connection to SMTP server. | |||||||||||||
| SemailFrom | 1.3.6.1.4.1.42111.640.7.6.4 | DisplayString (SIZE (0..63)) | RW | ||||||||||
scalar · DisplayString (SIZE (0..63)) · read-write · current This will show as the 'From' when you receive emails from this unit. | |||||||||||||
| SemailUsername | 1.3.6.1.4.1.42111.640.7.6.5 | DisplayString (SIZE (0..63)) | RW | ||||||||||
scalar · DisplayString (SIZE (0..63)) · read-write · current The email address to send from. | |||||||||||||
| SemailPassword | 1.3.6.1.4.1.42111.640.7.6.6 | DisplayString (SIZE (0..31)) | RW | ||||||||||
scalar · DisplayString (SIZE (0..31)) · read-write · current The password to the email address to send from. | |||||||||||||
| TrecipientTable | 1.3.6.1.4.1.42111.640.7.6.7 | NA | |||||||||||
table · not-accessible · current Table of 10 email recipients. | |||||||||||||
| RrecipientEntry | 1.3.6.1.4.1.42111.640.7.6.7.1 | NA | |||||||||||
| CrecipientIndex | 1.3.6.1.4.1.42111.640.7.6.7.1.1 | Integer32 (1..10) | NA | ||||||||||
column · Integer32 (1..10) · not-accessible · current Index of recipient (recipients 1 through 10). | |||||||||||||
| CemailAddress | 1.3.6.1.4.1.42111.640.7.6.7.1.2 | DisplayString (SIZE (0..63)) | RW | ||||||||||
column · DisplayString (SIZE (0..63)) · read-write · current Email address for the recipient of email notifications. | |||||||||||||
| CaudioLossEmail | 1.3.6.1.4.1.42111.640.7.6.7.1.3 | OnOff | RW | ||||||||||
column · OnOff · read-write · current This recipient will receive Audio Loss emails. | |||||||||||||
| ClowSignalEmail | 1.3.6.1.4.1.42111.640.7.6.7.1.4 | OnOff | RW | ||||||||||
column · OnOff · read-write · current This recipient will receive Low Signal emails. | |||||||||||||
| CrdsLossEmail | 1.3.6.1.4.1.42111.640.7.6.7.1.5 | OnOff | RW | ||||||||||
column · OnOff · read-write · current This recipient will receive RDS Loss emails. | |||||||||||||
| CpilotLossEmail | 1.3.6.1.4.1.42111.640.7.6.7.1.6 | OnOff | RW | ||||||||||
column · OnOff · read-write · current This recipient will receive Pilot Loss emails. | |||||||||||||
| CdailyLogEmail | 1.3.6.1.4.1.42111.640.7.6.7.1.7 | OnOff | RW | ||||||||||
column · OnOff · read-write · current This recipient will receive daily log emails. | |||||||||||||
| CweeklyLogEmail | 1.3.6.1.4.1.42111.640.7.6.7.1.8 | OnOff | RW | ||||||||||
column · OnOff · read-write · current This recipient will receive weekly log emails. | |||||||||||||
| CmonthlyLogEmail | 1.3.6.1.4.1.42111.640.7.6.7.1.9 | OnOff | RW | ||||||||||
column · OnOff · read-write · current This recipient will receive monthly log emails. | |||||||||||||
| NalarmLog | 1.3.6.1.4.1.42111.640.7.7 | ||||||||||||
| SalarmLogStatus | 1.3.6.1.4.1.42111.640.7.7.1 | Integer32 (0..100) | RW | ||||||||||
scalar · Integer32 (0..100) · read-write · current Fullness of alarm log (units: %). Set to 0 to clear the alarm log. | |||||||||||||
| SalarmLogFullEmail | 1.3.6.1.4.1.42111.640.7.7.2 | Integer32 (1..100) | RW | ||||||||||
scalar · Integer32 (1..100) · read-write · current Send an email reminder when the log is (%) full. | |||||||||||||
| NalarmPolarity | 1.3.6.1.4.1.42111.640.7.8 | ||||||||||||
| SaudioLossPolarity | 1.3.6.1.4.1.42111.640.7.8.1 | INTEGER | RW | ||||||||||
scalar · INTEGER · read-write · current Polarity of the Audio Loss alarm output.
| |||||||||||||
| SlowSignalPolarity | 1.3.6.1.4.1.42111.640.7.8.2 | INTEGER | RW | ||||||||||
scalar · INTEGER · read-write · current Polarity of the Low Signal alarm output.
| |||||||||||||
| SrdsLossPolarity | 1.3.6.1.4.1.42111.640.7.8.3 | INTEGER | RW | ||||||||||
scalar · INTEGER · read-write · current Polarity of the RDS Loss alarm output.
| |||||||||||||
| SpilotLossPolarity | 1.3.6.1.4.1.42111.640.7.8.4 | INTEGER | RW | ||||||||||
scalar · INTEGER · read-write · current Polarity of the Pilot Loss alarm output.
| |||||||||||||
| Nregion | 1.3.6.1.4.1.42111.640.7.9 | ||||||||||||
| StuningSteps | 1.3.6.1.4.1.42111.640.7.9.1 | INTEGER | RW | ||||||||||
scalar · INTEGER · read-write · current The step size used when tuning from the front panel and web.
| |||||||||||||
| Sdeemphasis | 1.3.6.1.4.1.42111.640.7.9.2 | INTEGER | RW | ||||||||||
scalar · INTEGER · read-write · current Set deemphasis to 50us or 75us.
| |||||||||||||
| SrdsDecodeMode | 1.3.6.1.4.1.42111.640.7.9.3 | INTEGER | RW | ||||||||||
scalar · INTEGER · read-write · current Set RDS decoding mode to RDS (Europe) or RBDS (North America).
| |||||||||||||
| NtestOscillator | 1.3.6.1.4.1.42111.640.7.10 | ||||||||||||
| SoscMode | 1.3.6.1.4.1.42111.640.7.10.1 | INTEGER | RW | ||||||||||
scalar · INTEGER · read-write · current Enable/disable the internal tone generator for testing purposes.
| |||||||||||||
| SoscFrequency | 1.3.6.1.4.1.42111.640.7.10.2 | Integer32 (10..20000) | RW | ||||||||||
scalar · Integer32 (10..20000) · read-write · current Frequency of the test oscillator (Units: Hz). Can be set in multiples of 10Hz. | |||||||||||||
| SoscLevel | 1.3.6.1.4.1.42111.640.7.10.3 | Integer32 (-30..0) | RW | ||||||||||
scalar · Integer32 (-30..0) · read-write · current Level of the test oscillator (Units: dB). | |||||||||||||
| Npasswords | 1.3.6.1.4.1.42111.640.8 | ||||||||||||
| SfrontPanelPassword | 1.3.6.1.4.1.42111.640.8.1 | DisplayString (SIZE (0..31)) | RW | ||||||||||
scalar · DisplayString (SIZE (0..31)) · read-write · current The password for restricting front panel access. | |||||||||||||
| SwebpagesPassword | 1.3.6.1.4.1.42111.640.8.2 | DisplayString (SIZE (0..31)) | RW | ||||||||||
scalar · DisplayString (SIZE (0..31)) · read-write · current The password for restricting webpage access. | |||||||||||||
Textual conventions
OnOffINTEGERoff(0)on(1)Represents a boolean value.
Traps / Notifications
- audioLossTrap
1.3.6.1.4.1.42111.640.1.0.1 - lowSignalTrap
1.3.6.1.4.1.42111.640.1.0.2 - pilotLossTrap
1.3.6.1.4.1.42111.640.1.0.4 - rdsErrorTrap
1.3.6.1.4.1.42111.640.1.0.3