snmptranslate -m CME-MIB -Tpsnmpwalk -v2c -c <community> -m CME-MIB <host> 1.3.6.1.4.1.2Imports
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP |
|---|---|
| SNMPv2-SMI | Bits, Integer32, IpAddress, MODULE-IDENTITY, MibIdentifier, OBJECT-IDENTITY, OBJECT-TYPE, TRAP-TYPE, TimeTicks, Unsigned32, enterprises, iso |
| SNMPv2-TC | DisplayString, PhysAddress, TEXTUAL-CONVENTION |
OID tree
| Name | OID | Type | Access | Status |
|---|---|---|---|---|
| Nibm | 1.3.6.1.4.1.2 | |||
| NibmAgents | 1.3.6.1.4.1.2.3 | |||
| NnetfinitySupportProcessorAgent | 1.3.6.1.4.1.2.3.51 | |||
| NbladeCenterSnmpMIB | 1.3.6.1.4.1.2.3.51.2 | |||
| Nmonitors | 1.3.6.1.4.1.2.3.51.2.2 | |||
| Ntemperature | 1.3.6.1.4.1.2.3.51.2.2.1 | |||
| NinternalTemp | 1.3.6.1.4.1.2.3.51.2.2.1.1 | |||
| ScmmTemp | 1.3.6.1.4.1.2.3.51.2.2.1.1.2 | OCTET STRING | RO | deprecated |
scalar · OCTET STRING · read-only · deprecated This field is deprecated. The return value of this field is the same as rearLEDCardTemp.
Chassis management module temperature in degrees centigrade(C).
An octet string expressed as 'sddd.dd Centigrade' where:
s is the sign ('-' for negative or blank space for positive)
d is a decimal digit or blank space for leading zeroes.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system. | ||||
| NambientTemp | 1.3.6.1.4.1.2.3.51.2.2.1.5 | |||
| SrearLEDCardTempAvg | 1.3.6.1.4.1.2.3.51.2.2.1.5.1 | OCTET STRING | RO | mandatory |
scalar · OCTET STRING · read-only · mandatory The average rear LED card temperature in degrees centigrade(C).
This is surrounding temperature where the system is installed.
An octet string expressed as 'sddd.dd Centigrade' where:
s is the sign ('-' for negative or blank space for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system. | ||||
| SrearLEDCardTempMin | 1.3.6.1.4.1.2.3.51.2.2.1.5.2 | OCTET STRING | RO | mandatory |
scalar · OCTET STRING · read-only · mandatory The minimum rear LED card temperature in degrees centigrade(C).
This is surrounding temperature where the system is installed.
An octet string expressed as 'sddd.dd Centigrade' where:
s is the sign ('-' for negative or blank space for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system. | ||||
| SrearLEDCardTempMax | 1.3.6.1.4.1.2.3.51.2.2.1.5.3 | OCTET STRING | RO | mandatory |
scalar · OCTET STRING · read-only · mandatory The maximum rear LED card temperature in degrees centigrade(C).
This is surrounding temperature where the system is installed.
An octet string expressed as 'sddd.dd Centigrade' where:
s is the sign ('-' for negative or blank space for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system. | ||||
| NmonitorTemp | 1.3.6.1.4.1.2.3.51.2.2.1.9 | |||
| ShotAirRecircMonitoring | 1.3.6.1.4.1.2.3.51.2.2.1.9.3 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory If this is enabled, the management module will monitor for Hot Air Recirculation by detecting non-uniform air temperature(s) that may be entering the front of the chassis. This could be due to either localized hot or cold air reaching at least one of the node's or chassis temperature sensors and it exceeding the acceptable range. When enabled, this monitor will generate an event and be transmitted to any configured remote alert recipient.
| ||||
| ShotAirRecircTempDeltaThresh | 1.3.6.1.4.1.2.3.51.2.2.1.9.5 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory This object is used to read or change the temperature delta threshold for Hot Air Recirculation detection. Values are enforced to be in the inclusive range between 5.00C and 9.00C and are specified as hundreths of a degree. For example, a value of 659 would equate to a threshold of 6.59 degrees C. | ||||
| ThotAirRecircStatusTable | 1.3.6.1.4.1.2.3.51.2.2.1.9.7 | NA | mandatory | |
table · not-accessible · mandatory Table of hot air recirculation status information. | ||||
| RhotAirRecircStatusEntry | 1.3.6.1.4.1.2.3.51.2.2.1.9.7.1 | NA | mandatory | |
row · not-accessible · mandatory Hot air recirculation status entry | ||||
| ChotAirRecircStatusTopologyPath | 1.3.6.1.4.1.2.3.51.2.2.1.9.7.1.2 | OCTET STRING (SIZE (0..100)) | RO | mandatory |
column · OCTET STRING (SIZE (0..100)) · read-only · mandatory The unique identifier for a component in this table. The chassis and each installed component is represented by a hardware topology tree, where each node in the tree represents a component. The path to a particular component consists of one or more <component>,<instance> pairs, where each successive pair is a child of the previous parent pair. As an example, the root of the tree is the chassis and is represented by the pair 'CHASSIS, 1'. This pair indicates the first instance of the chassis. If a blade is inserted in slot 4 of the chassis, its topology path is 'CHASSIS, 1, BLADE, 4'. With this format, the components in the chassis can be determined along with their relative hierarchy to each other. Note that this TP is preceded by a single octet that specifies the TP length. This is required since this table is indexed with two indices and, therefore, the TP length must be explicitly provided. This component firmware table is indexed by this unique topology path and the numeric designations for the components are: CHASSIS, 0x01 Chassis MM, 0x02 Management Module BLADE, 0x03 Main system board of a blade POWER, 0x04 Power Supply, Power Module, etc COOLING, 0x05 Fan, blower, or other cooling device IO_MODULE, 0x06 Has I/O interface, i.e. - switch or bridge MEDIA, 0x07 Media device PROCESSOR, 0x08 Any processor, processor module, etc STORAGE, 0x09 Any type of storage device EXPANSION, 0x0A Expansion Card (not covered by more specific type) MEMORY, 0x0B Any memory device, module, etc MFRU, 0x0C Managed FRU Device PANEL, 0x0D Any sort of panel device, such as a front panel BLADE_EXPANSION_MODULE, 0x0E Expansion option (BEM) such as PEU, BSE, etc CARD_EXPANSION, 0x0F Expansion card, ie. daughter card CARD_HS_EXPANSION, 0x10 High Speed Expansion card, ie. daughter card INTERPOSER, 0x11 Interposer device CLOCK, 0x12 Clock card MUX, 0x13 Mulitplexer card ADDIN, 0x14 cKVM card & other addin cards STORAGE_MODULE, 0x15 Container of one or more Storage Devices SYS_EXPANSION_CARD, 0x16 Management card BATTERY, 0x17 A single battery BATTERY_MODULE, 0x18 Container of one or more batteries REAR_LED, 0x19 Rear LED card MEMORY_BANK, 0x1A Memory banks AIR_FILTER, 0x1B Filter mechanism (bezel) SERIAL_PORT_MODULE, 0x1C Container of one or more serial ports PARENT, 0x1D Reference to parent for multi-parent support PHY_PORT, 0x1E Physical port IO_EXPANDER, 0x1F RAID card CABLE, 0x20 Cable/Interconnect FAN_MUX 0x29 Fan multiplexer card PCI_EXPRESS, 0x32 PCI express card on (PEN) FLASH_DIMM, 0x33 Used for SPD devices that matches the silkscreen of the DIMM slot RACK, 0x50 Rack PLATFORM, 0x51 Generic Platform like rack mounted server/appliance DATAPLEX, 0x52 DataPlex OTHER, 0x53 Other unknown etc. PERIPHERAL_MODULE, 0x54 SYSTEM_BOARD, 0x55 System board PROCESSOR_MODULE, 0x56 BACK_PANEL, 0x57 POWER_SYSTEM_BOARD, 0x58 STORAGE_BACKPLANE, 0x59 Drive back plane PROC_BOARD, 0x5A Holds 1 or more processors POWER_DI, 0x5B Power mgt / power distribution board CHASSIS_BACK_PANEL, 0x5C SUB_CHASSIS, 0x5D OTHER_CHASSIS_BOARD, 0x5E DEVICE_MODULE, 0x5F REMOTE_DEVICE, 0x60 Remote mgt communication device EXTERNAL_ENVIRONMENT, 0x61 Such as external temp sensor for outside box temps PROC_MEMORY_MODULE, 0x62 Processors and memory on same module | ||||
| ChotAirRecircStatusIndex | 1.3.6.1.4.1.2.3.51.2.2.1.9.7.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Each component may have one or more sensor associated with it, this index object identifies the particular instance. | ||||
| ChotAirRecircStatusName | 1.3.6.1.4.1.2.3.51.2.2.1.9.7.1.4 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The name of the component as a null terminated string | ||||
| ChotAirRecircStatusSensorLabel | 1.3.6.1.4.1.2.3.51.2.2.1.9.7.1.5 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The text label of the sensor as a null terminated string | ||||
| ChotAirRecircStatusSensorReading | 1.3.6.1.4.1.2.3.51.2.2.1.9.7.1.6 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Ambient temperature reading for this component in degrees centigrade(C). The string is formatted as 'dd.dd Centigrade'. | ||||
| ChotAirRecircStatusExceeded | 1.3.6.1.4.1.2.3.51.2.2.1.9.7.1.7 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether this component has exceeded the threshold of the acceptable temperature being monitored for hot air recirculation.
| ||||
| NchassisFans | 1.3.6.1.4.1.2.3.51.2.2.3 | |||
| TchassisFansTable | 1.3.6.1.4.1.2.3.51.2.2.3.50 | NA | mandatory | |
table · not-accessible · mandatory Table of chassis Fan information. | ||||
| RchassisFansEntry | 1.3.6.1.4.1.2.3.51.2.2.3.50.1 | NA | mandatory | |
| CchassisFanIndex | 1.3.6.1.4.1.2.3.51.2.2.3.50.1.1 | INTEGER (0..128) | RO | mandatory |
column · INTEGER (0..128) · read-only · mandatory Chassis Fans table index. | ||||
| CchassisFanId | 1.3.6.1.4.1.2.3.51.2.2.3.50.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The numeric chassis fan ID.
| ||||
| CchassisFanSpeed | 1.3.6.1.4.1.2.3.51.2.2.3.50.1.3 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Chassis fan speed expressed in percent(%) of maximum RPM. An octet string expressed as 'ddd% of maximum' where: d is a decimal digit or blank space for a leading zero. If the chassis fan is determined not to be running or the chassis fan speed cannot be determined, the string will indicate 'Offline'. The string 'Not Readable!' indicates that the given monitor is not supported on this system. | ||||
| CchassisFanState | 1.3.6.1.4.1.2.3.51.2.2.3.50.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The health state for the chassis fan. Note that the other UIs may use slightly different terminology for the three health state values, as such: WEB - Normal, Attention, Critical CLI - OK, Non-critical, Critical
| ||||
| CchassisFanSpeedRPM | 1.3.6.1.4.1.2.3.51.2.2.3.50.1.5 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Chassis fan speed expressed in RPM. If the chassis fan is determined not to be running or the chassis fan speed cannot be determined, the string will indicate 'Offline'. The string 'Not Readable!' indicates that the given monitor is not supported on this system. | ||||
| CchassisFanControllerState | 1.3.6.1.4.1.2.3.51.2.2.3.50.1.6 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The controller health state for the chassis fan.
| ||||
| CchassisFanCoolingZone | 1.3.6.1.4.1.2.3.51.2.2.3.50.1.7 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The cooling zone for the chassis fan.
| ||||
| TchassisCoolingZoneTable | 1.3.6.1.4.1.2.3.51.2.2.3.51 | NA | mandatory | |
table · not-accessible · mandatory Table of chassis cooling zone information. | ||||
| RchassisCoolingZoneEntry | 1.3.6.1.4.1.2.3.51.2.2.3.51.1 | NA | mandatory | |
| CchassisCoolingIndex | 1.3.6.1.4.1.2.3.51.2.2.3.51.1.1 | INTEGER (0..128) | RO | mandatory |
column · INTEGER (0..128) · read-only · mandatory Chassis Cooling Zones table index. | ||||
| CchassisCoolingZone | 1.3.6.1.4.1.2.3.51.2.2.3.51.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The cooling zone for the chassis component.
| ||||
| CchassisCoolingZoneStatus | 1.3.6.1.4.1.2.3.51.2.2.3.51.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The health state of the chassis cooling zone. Note: This is the health of the cooling zone, not the health status of the component in chassisCoolingZoneComponent. Note that the other UIs may use slightly different terminology for the three health state values, as such: WEB - Normal, Attention, Critical CLI - OK, Non-critical, Critical
| ||||
| CchassisCoolingZoneComponent | 1.3.6.1.4.1.2.3.51.2.2.3.51.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory A component within a cooling zone.
| ||||
| NpowerModuleHealth | 1.3.6.1.4.1.2.3.51.2.2.4 | |||
| TpowerModuleHealthTable | 1.3.6.1.4.1.2.3.51.2.2.4.1 | NA | mandatory | |
table · not-accessible · mandatory Table of power module health information. Contains the power health information for each power module. | ||||
| RpowerModuleHealthEntry | 1.3.6.1.4.1.2.3.51.2.2.4.1.1 | NA | mandatory | |
| CpowerModuleIndex | 1.3.6.1.4.1.2.3.51.2.2.4.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Power module index. | ||||
| CpowerModuleExists | 1.3.6.1.4.1.2.3.51.2.2.4.1.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether the power module specified exists or not.
| ||||
| CpowerModuleState | 1.3.6.1.4.1.2.3.51.2.2.4.1.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The health state for the power module. Note that the other UIs may use slightly different terminology for the three health state values, as such: WEB - Normal, Attention, Critical CLI - OK, Non-critical, Critical
| ||||
| CpowerModuleDetails | 1.3.6.1.4.1.2.3.51.2.2.4.1.1.4 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The details for this power module. | ||||
| CpowerModuleDescription | 1.3.6.1.4.1.2.3.51.2.2.4.1.1.9 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The description for this power module. | ||||
| NspStatus | 1.3.6.1.4.1.2.3.51.2.2.5 | |||
| NmmBistAndChassisStatus | 1.3.6.1.4.1.2.3.51.2.2.5.2 | |||
| SbistRtc | 1.3.6.1.4.1.2.3.51.2.2.5.2.5 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory MM BIST Real Time Clock test result.
| ||||
| SbistLocalI2CBus | 1.3.6.1.4.1.2.3.51.2.2.5.2.7 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory MM BIST Local I2C bus test result.
| ||||
| SbistPrimaryMainAppFlashImage | 1.3.6.1.4.1.2.3.51.2.2.5.2.8 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory MM BIST Primary Main Application Firmware test result.
| ||||
| SbistSecondaryMainAppFlashImage | 1.3.6.1.4.1.2.3.51.2.2.5.2.9 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory MM BIST Secondary Main Application test result.
| ||||
| SbistBootRomFlashImage | 1.3.6.1.4.1.2.3.51.2.2.5.2.10 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory MM BIST Boot Firmware test result.
| ||||
| SbistEthernetPort1 | 1.3.6.1.4.1.2.3.51.2.2.5.2.11 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory MM BIST external eth0 ethernet port test result.
| ||||
| SbistExternalI2CDevices | 1.3.6.1.4.1.2.3.51.2.2.5.2.14 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory MM BIST external I2C devices test result.
| ||||
| SbistInternalEthernetSwitch | 1.3.6.1.4.1.2.3.51.2.2.5.2.19 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory MM BIST internal external switch test result.
| ||||
| SbistPrimaryKernel | 1.3.6.1.4.1.2.3.51.2.2.5.2.25 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory MM BIST primary kernel test result.
| ||||
| SbistSecondaryKernel | 1.3.6.1.4.1.2.3.51.2.2.5.2.26 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory MM BIST secondary kernel test result.
| ||||
| SbistPhysicalNetworkLink | 1.3.6.1.4.1.2.3.51.2.2.5.2.29 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory MM BIST Physical Network Link test result.
| ||||
| SbistLogicalNetworkLink | 1.3.6.1.4.1.2.3.51.2.2.5.2.30 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory MM BIST Logical Network Link test result.
| ||||
| SbistBladesInstalled | 1.3.6.1.4.1.2.3.51.2.2.5.2.33 | OCTET STRING | RO | mandatory |
scalar · OCTET STRING · read-only · mandatory The blades that are installed on the chassis. The blades are listed as a bitmap. The bitmap is a string containing a list of 1's and 0's that is as long as the number of blades supported. If a blade is installed in a bay, a 1 is present in the string in the position representing the bay ID as read from left to right. For example, if blades are installed in bays 1, 5, and 13, and 14 blades are supported, the string would look like '10001000000010'. | ||||
| SbistBladesCommunicating | 1.3.6.1.4.1.2.3.51.2.2.5.2.49 | OCTET STRING | RO | mandatory |
scalar · OCTET STRING · read-only · mandatory The blades that are communicating on the chassis. The blades are listed as a bitmap. The bitmap is a string containing a list of 1's and 0's that is as long as the number of blades supported. If a blade installed in a bay is communicating, a 1 is present in the string in the position representing the bay ID as read from left to right. For example, if blades are communicating in bays 1, 5, and 13, and 14 blades are supported, the string would look like '10001000000010'. | ||||
| SbistChassisFansInstalled | 1.3.6.1.4.1.2.3.51.2.2.5.2.65 | OCTET STRING | RO | mandatory |
scalar · OCTET STRING · read-only · mandatory The chassis fans that are installed on the chassis. They are listed as a bitmap. The bitmap is a string containing a list of 1's and 0's that is as long as the number supported. If one is installed in a bay, a 1 is present in the string in the position representing the bay ID as read from left to right. For example, if it is installed in bay 1, and 2 are supported, the string would look like '10'. | ||||
| SbistChassisFansFunctional | 1.3.6.1.4.1.2.3.51.2.2.5.2.73 | OCTET STRING | RO | mandatory |
scalar · OCTET STRING · read-only · mandatory The chassis fans installed on the chassis that are functional. They are listed as a bitmap. The bitmap is a string containing a list of 1's and 0's that is as long as the number supported. If one is installed in a bay, a 1 is present in the string in the position representing the bay ID as read from left to right. For example, if it is installed in bay 1, and 2 are supported, the string would look like '10'. | ||||
| SbistRearLEDCardInstalled | 1.3.6.1.4.1.2.3.51.2.2.5.2.74 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory Indicates whether a rear LED card is installed
| ||||
| SbistRearLEDCardCommunicating | 1.3.6.1.4.1.2.3.51.2.2.5.2.75 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory Indicates whether a rear LED card is communicating
| ||||
| SbistOtherMMInstalled | 1.3.6.1.4.1.2.3.51.2.2.5.2.76 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory Indicates whether a redundant MM is installed.
| ||||
| SbistOtherMMCommunicating | 1.3.6.1.4.1.2.3.51.2.2.5.2.77 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory Indicates whether a redundant MM is communicating.
| ||||
| SbistPowerModulesInstalled | 1.3.6.1.4.1.2.3.51.2.2.5.2.81 | OCTET STRING | RO | mandatory |
scalar · OCTET STRING · read-only · mandatory The power modules that are installed on the chassis. The power modules are listed as a bitmap. The bitmap is a string containing a list of 1's and 0's that is as long as the number of power modules supported. If a power module is installed in a bay, a 1 is present in the string in the position representing the bay ID as read from left to right. For example, if power modules are installed in bays 1 and 3, and 4 power modules are supported, the string would look like '1010'. | ||||
| SbistPowerModulesFunctional | 1.3.6.1.4.1.2.3.51.2.2.5.2.89 | OCTET STRING | RO | mandatory |
scalar · OCTET STRING · read-only · mandatory The power modules that are functional on the chassis. The power modules are listed as a bitmap. The bitmap is a string containing a list of 1's and 0's that is as long as the number of power modules supported. If a power module is installed and functioning in a bay, a 1 is present in the string in the position representing the bay ID as read from left to right. For example, if power modules are installed and functioning in bays 1 and 3, and 4 power modules are supported, the string would look like '1010'. | ||||
| SbistSwitchModulesInstalled | 1.3.6.1.4.1.2.3.51.2.2.5.2.97 | OCTET STRING | RO | mandatory |
scalar · OCTET STRING · read-only · mandatory The switch modules that are installed on the chassis. The switch modules are listed as a bitmap. The bitmap is a string containing a list of 1's and 0's that is as long as the number of switch modules supported. If a switch module is installed in a bay, a 1 is present in the string in the position representing the bay ID as read from left to right. For example, if switch modules are installed in bays 1 and 3, and 4 switch modules are supported, the string would look like '1011'. | ||||
| SbistSwitchModulesCommunicating | 1.3.6.1.4.1.2.3.51.2.2.5.2.113 | OCTET STRING | RO | mandatory |
scalar · OCTET STRING · read-only · mandatory The switch modules that are communicating on the chassis. The switch modules are listed as a bitmap. The bitmap is a string containing a list of 1's and 0's that is as long as the number of switch modules supported. If a switch module is installed and functioning in a bay, a 1 is present in the string in the position representing the bay ID as read from left to right. For example, if switch modules are installed and functioning in bays 1 and 3, and 4 switch modules are supported, the string would look like '1011'. | ||||
| SbistChassisFansMUXAInstalled | 1.3.6.1.4.1.2.3.51.2.2.5.2.120 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory Indicates whether chassis fan MUX A is installed
| ||||
| SbistChassisFansMUXAFunctional | 1.3.6.1.4.1.2.3.51.2.2.5.2.121 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory Indicates whether chassis fan MUX A is functional
| ||||
| SbistChassisFansMUXBInstalled | 1.3.6.1.4.1.2.3.51.2.2.5.2.122 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory Indicates whether chassis fan MUX B is installed
| ||||
| SbistChassisFansMUXBFunctional | 1.3.6.1.4.1.2.3.51.2.2.5.2.123 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory Indicates whether chassis fan MUX B is functional
| ||||
| SbistLastUpdate | 1.3.6.1.4.1.2.3.51.2.2.5.2.200 | OCTET STRING | RO | mandatory |
scalar · OCTET STRING · read-only · mandatory It is the time when the primary MM updated the last BIST results. | ||||
| NrmmBistAndChassisStatus | 1.3.6.1.4.1.2.3.51.2.2.5.3 | |||
| SrbistRtc | 1.3.6.1.4.1.2.3.51.2.2.5.3.5 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory Standby MM BIST Real Time Clock test result. The time of the last update can be obtained by querying rbistUpdateTime object.
| ||||
| SrbistLocalI2CBus | 1.3.6.1.4.1.2.3.51.2.2.5.3.7 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory Standby MM BIST Local I2C bus test result. The time of the last update can be obtained by querying rbistUpdateTime object.
| ||||
| SrbistEthernetPort1 | 1.3.6.1.4.1.2.3.51.2.2.5.3.11 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory Standby MM BIST external ethernet port test result. The time of the last update can be obtained by querying rbistUpdateTime object.
| ||||
| SrbistExternalI2CDevices | 1.3.6.1.4.1.2.3.51.2.2.5.3.14 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory Standby MM BIST external I2C devices test result collected when the standby MM was primary. The time of the last update can be obtained by querying rbistUpdateTimePrimary object.
| ||||
| SrbistInternalEthernetSwitch | 1.3.6.1.4.1.2.3.51.2.2.5.3.19 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory Standby MM BIST internal external switch test result. The time of the last update can be obtained by querying rbistUpdateTime object.
| ||||
| SrbistPhysicalNetworkLink | 1.3.6.1.4.1.2.3.51.2.2.5.3.29 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory Standby MM BIST Physical Network Link test result collected when the standby MM was primary. The time of the last update can be obtained by querying rbistUpdateTimePrimary object.
| ||||
| SrbistLogicalNetworkLink | 1.3.6.1.4.1.2.3.51.2.2.5.3.30 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory Standby MM BIST Logical Network Link test result collected when the standby MM was primary. The time of the last update can be obtained by querying rbistUpdateTimePrimary object.
| ||||
| SrbistBladesInstalled | 1.3.6.1.4.1.2.3.51.2.2.5.3.33 | OCTET STRING | RO | mandatory |
scalar · OCTET STRING · read-only · mandatory The blades that were installed on the chassis when the standby MM was once primary. The time of the last update can be obtained by querying rbistUpdateTimePrimary object. The blades are listed as a bitmap. The bitmap is a string containing a list of 1's and 0's that is as long as the number of blades supported. If a blade is installed in a bay, a 1 is present in the string in the position representing the bay ID as read from left to right. For example, if blades are installed in bays 1, 5, and 13, and 14 blades are supported, the string would look like '10001000000010'. | ||||
| SrbistBladesCommunicating | 1.3.6.1.4.1.2.3.51.2.2.5.3.49 | OCTET STRING | RO | mandatory |
scalar · OCTET STRING · read-only · mandatory The blades that were communicating on the chassis when the standby MM was once primary. The time of the last update can be obtained by querying rbistUpdateTimePrimary object. The blades are listed as a bitmap. The bitmap is a string containing a list of 1's and 0's that is as long as the number of blades supported. If a blade installed in a bay is communicating, a 1 is present in the string in the position representing the bay ID as read from left to right. For example, if blades are communicating in bays 1, 5, and 13, and 14 blades are supported, the string would look like '10001000000010'. | ||||
| SrbistChassisFansInstalled | 1.3.6.1.4.1.2.3.51.2.2.5.3.65 | OCTET STRING | RO | mandatory |
scalar · OCTET STRING · read-only · mandatory The chassis fans that were installed on the chassis when the standby MM was once primary. The time of the last update can be obtained by querying rbistUpdateTimePrimary object. They are listed as a bitmap. The bitmap is a string containing a list of 1's and 0's that is as long as the number of chassis fans supported. If it is installed in a bay, a 1 is present in the string in the position representing the bay ID as read from left to right. For example, if it is installed in bay 1, and 2 are supported, the string would look like '10'. | ||||
| SrbistChassisFansFunctional | 1.3.6.1.4.1.2.3.51.2.2.5.3.73 | OCTET STRING | RO | mandatory |
scalar · OCTET STRING · read-only · mandatory The chassis fans installed on the chassis that were functional when the standby MM was once primary. The time of the last update can be obtained by querying rbistUpdateTimePrimary object. They are listed as a bitmap. The bitmap is a string containing a list of 1's and 0's that is as long as the number supported. If it is installed and functional in a bay, a 1 is present in the string in the position representing the bay ID as read from left to right. For example, if one is installed and functional only in bay 1, and 2 are supported, the string would look like '10'. | ||||
| SrbistRearLEDCardInstalled | 1.3.6.1.4.1.2.3.51.2.2.5.3.74 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory Indicates whether a rear LED card is installed
| ||||
| SrbistRearLEDCardCommunicating | 1.3.6.1.4.1.2.3.51.2.2.5.3.75 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory Indicates whether a rear LED card is communicating
| ||||
| SrbistOtherMMInstalled | 1.3.6.1.4.1.2.3.51.2.2.5.3.76 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory Indicates whether a standby MM was installed when the standby MM was once primary.The time of the last update can be obtained by querying rbistUpdateTimePrimary object.
| ||||
| SrbistOtherMMCommunicating | 1.3.6.1.4.1.2.3.51.2.2.5.3.77 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory Indicates whether a standby MM was communicating when the standby MM was once primary. The time of the last update can be gotten from the object 'rbistUpdateTimePrimary'.
| ||||
| SrbistPowerModulesInstalled | 1.3.6.1.4.1.2.3.51.2.2.5.3.81 | OCTET STRING | RO | mandatory |
scalar · OCTET STRING · read-only · mandatory The power modules that were installed on the chassis when the standby MM was once primary. The time of the last update can be obtained by querying rbistUpdateTimePrimary object. The power modules are listed as a bitmap. The bitmap is a string containing a list of 1's and 0's that is as long as the number of power modules supported. If a power module was installed in a bay, a 1 is present in the string in the position representing the bay ID as read from left to right. For example, if power modules were installed in bays 1 and 3, and 4 power modules were supported, the string would look like '1010'. | ||||
| SrbistPowerModulesFunctional | 1.3.6.1.4.1.2.3.51.2.2.5.3.89 | OCTET STRING | RO | mandatory |
scalar · OCTET STRING · read-only · mandatory The power modules that were functional on the chassis when the standby MM was once primary. The time of the last update can be obtained by querying rbistUpdateTimePrimary object. The power modules are listed as a bitmap. The bitmap is a string containing a list of 1's and 0's that is as long as the number of power modules supported. If a power module was installed and functioning in a bay, a 1 is present in the string in the position representing the bay ID as read from left to right. For example, if power modules were installed and functioning in bays 1 and 3, and 4 power modules were supported, the string would look like '1010'. | ||||
| SrbistSwitchModulesInstalled | 1.3.6.1.4.1.2.3.51.2.2.5.3.97 | OCTET STRING | RO | mandatory |
scalar · OCTET STRING · read-only · mandatory The switch modules that were installed on the chassis when the standby MM was once primary. The time of the last update can be obtained by querying rbistUpdateTimePrimary object. The switch modules are listed as a bitmap. The bitmap is a string containing a list of 1's and 0's that is as long as the number of switch modules supported. If a switch module was installed in a bay, a 1 is present in the string in the position representing the bay ID as read from left to right. For example, if switch modules were installed in bays 1 and 3, and 4 switch modules were supported, the string would look like '1011'. | ||||
| SrbistSwitchModulesCommunicating | 1.3.6.1.4.1.2.3.51.2.2.5.3.113 | OCTET STRING | RO | mandatory |
scalar · OCTET STRING · read-only · mandatory The switch modules that are communicating on the chassis when the standby MM was once primary. The time of the last update can be obtained by querying rbistUpdateTimePrimary object. The switch modules are listed as a bitmap. The bitmap is a string containing a list of 1's and 0's that is as long as the number of switch modules supported. If a switch module was installed and functioning in a bay, a 1 is present in the string in the position representing the bay ID as read from left to right. For example, if switch modules were installed and functioning in bays 1 and 3, and 4 switch modules were supported, the string would look like '1011'. | ||||
| SrbistChassisFansMUXAInstalled | 1.3.6.1.4.1.2.3.51.2.2.5.3.120 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory Indicates whether chassis fan MUX A is installed
| ||||
| SrbistChassisFansMUXAFunctional | 1.3.6.1.4.1.2.3.51.2.2.5.3.121 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory Indicates whether chassis fan MUX A is functional
| ||||
| SrbistChassisFansMUXBInstalled | 1.3.6.1.4.1.2.3.51.2.2.5.3.122 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory Indicates whether chassis fan MUX B is installed
| ||||
| SrbistChassisFansMUXBFunctional | 1.3.6.1.4.1.2.3.51.2.2.5.3.123 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory Indicates whether chassis fan MUX B is functional
| ||||
| SrbistUpdateTime | 1.3.6.1.4.1.2.3.51.2.2.5.3.200 | OCTET STRING | RO | mandatory |
scalar · OCTET STRING · read-only · mandatory It is the time when the standby MM updated the last BIST results. | ||||
| SrbistLastUpdatePrimary | 1.3.6.1.4.1.2.3.51.2.2.5.3.201 | OCTET STRING | RO | mandatory |
scalar · OCTET STRING · read-only · mandatory It is the time when the standby MM updated the last BIST results when it was still primary. | ||||
| NfanPack | 1.3.6.1.4.1.2.3.51.2.2.6 | |||
| TfanPackTable | 1.3.6.1.4.1.2.3.51.2.2.6.1 | NA | mandatory | |
table · not-accessible · mandatory Table of fan pack information. Contains the information for each fan pack. NOTE: Fan packs are also referred to as Power Module Cooling Devices. | ||||
| RfanPackEntry | 1.3.6.1.4.1.2.3.51.2.2.6.1.1 | NA | mandatory | |
| CfanPackIndex | 1.3.6.1.4.1.2.3.51.2.2.6.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Fan Pack sequence index. | ||||
| CfanPackExists | 1.3.6.1.4.1.2.3.51.2.2.6.1.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether the fan pack specified exists or not.
| ||||
| CfanPackState | 1.3.6.1.4.1.2.3.51.2.2.6.1.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The health state for the fan pack. Note that the other UIs may use slightly different terminology for the three health state values, as such: WEB - Normal, Attention, Critical CLI - OK, Non-critical, Critical
| ||||
| CfanPackFanCount | 1.3.6.1.4.1.2.3.51.2.2.6.1.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The number of fans in the fan pack.
| ||||
| CfanPackAverageSpeed | 1.3.6.1.4.1.2.3.51.2.2.6.1.1.5 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The average speed of all fans in the fan pack expressed in percent(%) of maximum RPM. If the fan pack is determined not to be running or the fan pack speed cannot be determined, the string will indicate 'Offline'. The string 'Not Readable!' indicates that the given monitor is not supported on this system. | ||||
| CfanPackAverageSpeedRPM | 1.3.6.1.4.1.2.3.51.2.2.6.1.1.6 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The average speed of all fans in the fan pack expressed in RPM. If the fan pack is determined not to be running or the fan pack speed cannot be determined, the string will indicate 'Offline'. The string 'Not Readable!' indicates that the given monitor is not supported on this system. | ||||
| CfanPackControllerState | 1.3.6.1.4.1.2.3.51.2.2.6.1.1.7 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The health state for the controller for the fan pack.
| ||||
| NsystemHealth | 1.3.6.1.4.1.2.3.51.2.2.7 | |||
| SsystemHealthStat | 1.3.6.1.4.1.2.3.51.2.2.7.1 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory Indicates status of system health for the system in which the MM resides. Value of 'critical' indicates a severe error has occurred and the system may not be functioning. A value of 'nonCritical' indicates that a error has occurred but the system is currently functioning properly. A value of 'systemLevel' indicates that a condition has occurred that may change the state of the system in the future but currently the system is working properly. A value of 'normal' indicates that the system is operating normally.
| ||||
| TsystemHealthSummaryTable | 1.3.6.1.4.1.2.3.51.2.2.7.2 | NA | mandatory | |
table · not-accessible · mandatory Table of System Health summary. Contains more detailed information about the reasons for the overall system health status. | ||||
| RsystemHealthSummaryEntry | 1.3.6.1.4.1.2.3.51.2.2.7.2.1 | NA | mandatory | |
| CsystemHealthSummaryIndex | 1.3.6.1.4.1.2.3.51.2.2.7.2.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory System health summary index. | ||||
| CsystemHealthSummarySeverity | 1.3.6.1.4.1.2.3.51.2.2.7.2.1.2 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory System health summary severity. | ||||
| CsystemHealthSummaryDescription | 1.3.6.1.4.1.2.3.51.2.2.7.2.1.3 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory System health summary description. | ||||
| CsystemHealthSummaryDateTime | 1.3.6.1.4.1.2.3.51.2.2.7.2.1.4 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory System health summary date time. | ||||
| CsystemHealthSummaryAuxData | 1.3.6.1.4.1.2.3.51.2.2.7.2.1.11 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory System health summary auxilliary event data. If auxilliary event data is available, it is device-specific event data provided to the CMM by the device. | ||||
| CsystemHealthSummaryEventID | 1.3.6.1.4.1.2.3.51.2.2.7.2.1.12 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory System health summary event ID. | ||||
| Nleds | 1.3.6.1.4.1.2.3.51.2.2.8 | |||
| NfrontPanelLEDs | 1.3.6.1.4.1.2.3.51.2.2.8.1 | |||
| SfaultLED | 1.3.6.1.4.1.2.3.51.2.2.8.1.1 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory Indicates whether the front panel system error LED is on or off.
| ||||
| ScheckLogLED | 1.3.6.1.4.1.2.3.51.2.2.8.1.2 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Indicates whether the front panel system information LED is on or off. For Write access, the LED can be turned off only.
| ||||
| SidentifyLED | 1.3.6.1.4.1.2.3.51.2.2.8.1.4 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Indicates whether the front panel identity LED is on or off.
| ||||
| NbladeLEDs | 1.3.6.1.4.1.2.3.51.2.2.8.2 | |||
| TbladeLEDsTable | 1.3.6.1.4.1.2.3.51.2.2.8.2.1 | NA | mandatory | |
table · not-accessible · mandatory Table of blade status information. NOTE: Querying objects in this table may take significantly longer than normal, so it is recommended that the query timeout be set to a large value. On a fully populated chassis, the timeout should be set to 120 seconds or more. | ||||
| RbladeLEDsEntry | 1.3.6.1.4.1.2.3.51.2.2.8.2.1.1 | NA | mandatory | |
| CledBladeIndex | 1.3.6.1.4.1.2.3.51.2.2.8.2.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Blade LED table index. | ||||
| CledBladeId | 1.3.6.1.4.1.2.3.51.2.2.8.2.1.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The numeric blade ID.
| ||||
| CledBladeExists | 1.3.6.1.4.1.2.3.51.2.2.8.2.1.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether the blade specified exists or not.
| ||||
| CledBladePowerState | 1.3.6.1.4.1.2.3.51.2.2.8.2.1.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates the power state of the blade specified.
| ||||
| CledBladeHealthState | 1.3.6.1.4.1.2.3.51.2.2.8.2.1.1.5 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The system health state for the blade. Unknown: Blade is in an undefined state. Good: Blade is operating normally. Warning: One or more outstanding warnings exist for this blade. Critical: One or more outstanding critical events for this blade. Kernel Mode: Blade is in kernel mode. Discovering: The MM is currently in the process of discovering this blade. Communications Error: The MM failed to communicate with this blade. No Power: No power to the blade's domain. Flashing: Flashing in progress. Initialization Failure: Blade failed to initialized. Insufficient Power: Not enough power is left in the blade's domain to power the blade. Power Denied: Power was denied to the blade.
| ||||
| CledBladeName | 1.3.6.1.4.1.2.3.51.2.2.8.2.1.1.6 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The name of the blade as a null terminated string. | ||||
| CledBladeFault | 1.3.6.1.4.1.2.3.51.2.2.8.2.1.1.7 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether the blade fault LED is on or off.
| ||||
| CledBladeCheckLog | 1.3.6.1.4.1.2.3.51.2.2.8.2.1.1.8 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Indicates whether the blade check log information LED is on or off. For Write access, the LED can be turned off only.
| ||||
| CledBladeIdentify | 1.3.6.1.4.1.2.3.51.2.2.8.2.1.1.11 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Indicates whether the blade identify LED is on, off, or blinking.
| ||||
| TbladeLEDsDetailsTable | 1.3.6.1.4.1.2.3.51.2.2.8.2.2 | NA | mandatory | |
table · not-accessible · mandatory Table of blade LEDs detailed information. NOTE: Querying objects in this table may take significantly longer than normal, so it is recommended that the query timeout be set to a large value. On a fully populated chassis, the timeout should be set to 120 seconds or more. | ||||
| RbladeLEDsDetailsEntry | 1.3.6.1.4.1.2.3.51.2.2.8.2.2.1 | NA | mandatory | |
| CledIndex | 1.3.6.1.4.1.2.3.51.2.2.8.2.2.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The LED index number. | ||||
| CledBladeBayNumber | 1.3.6.1.4.1.2.3.51.2.2.8.2.2.1.2 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The bay number of the main server blade that the LED is grouped into. | ||||
| CledBladeComponentType | 1.3.6.1.4.1.2.3.51.2.2.8.2.2.1.3 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Type of the component/subcomponent grouping for this LED. | ||||
| CledBladeLabel | 1.3.6.1.4.1.2.3.51.2.2.8.2.2.1.4 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Text label for a LED. | ||||
| CledBladeState | 1.3.6.1.4.1.2.3.51.2.2.8.2.2.1.5 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Text description which denotes color or on/off/blink state for a LED.
| ||||
| CledBladeLocation | 1.3.6.1.4.1.2.3.51.2.2.8.2.2.1.6 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Location of this LED. | ||||
| NsmLEDs | 1.3.6.1.4.1.2.3.51.2.2.8.4 | |||
| TsmLEDsTable | 1.3.6.1.4.1.2.3.51.2.2.8.4.2 | NA | mandatory | |
table · not-accessible · mandatory Table of switch module LEDs information. | ||||
| RsmLEDsEntry | 1.3.6.1.4.1.2.3.51.2.2.8.4.2.1 | NA | mandatory | |
| CledSMIndex | 1.3.6.1.4.1.2.3.51.2.2.8.4.2.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Switch module LEDs table index. | ||||
| CledSMSlot | 1.3.6.1.4.1.2.3.51.2.2.8.4.2.1.2 | INTEGER (0..128) | RO | mandatory |
column · INTEGER (0..128) · read-only · mandatory The bay number of the switch. | ||||
| CledSMLabel | 1.3.6.1.4.1.2.3.51.2.2.8.4.2.1.3 | OCTET STRING (SIZE (256)) | RO | mandatory |
column · OCTET STRING (SIZE (256)) · read-only · mandatory The name associated with the LED. | ||||
| CledSMState | 1.3.6.1.4.1.2.3.51.2.2.8.4.2.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory NOTE: This table entry is read-write ONLY when Label = 'Enclosure Identity'. All other Label values have read-only access.
| ||||
| CledSMLocation | 1.3.6.1.4.1.2.3.51.2.2.8.4.2.1.5 | OCTET STRING (SIZE (256)) | RO | mandatory |
column · OCTET STRING (SIZE (256)) · read-only · mandatory The physical location where the LED can be found on the Switch. | ||||
| NchassisFanLEDs | 1.3.6.1.4.1.2.3.51.2.2.8.5 | |||
| TchassisFanLEDsTable | 1.3.6.1.4.1.2.3.51.2.2.8.5.1 | NA | mandatory | |
table · not-accessible · mandatory Table of chassis fan LEDs information. | ||||
| RchassisFanLEDsEntry | 1.3.6.1.4.1.2.3.51.2.2.8.5.1.1 | NA | mandatory | |
| CledChassisFanIndex | 1.3.6.1.4.1.2.3.51.2.2.8.5.1.1.1 | INTEGER (0..128) | RO | mandatory |
column · INTEGER (0..128) · read-only · mandatory Chassis fan LEDs table index. | ||||
| CledChassisFanId | 1.3.6.1.4.1.2.3.51.2.2.8.5.1.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The numeric chassis fan ID.
| ||||
| CledChassisFanExists | 1.3.6.1.4.1.2.3.51.2.2.8.5.1.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether the chassis fan specified exists or not.
| ||||
| CledChassisFanError | 1.3.6.1.4.1.2.3.51.2.2.8.5.1.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether the chassis fan error LED is on, off, or not available.
| ||||
| NfanPackLEDs | 1.3.6.1.4.1.2.3.51.2.2.8.6 | |||
| TfanPackLEDsTable | 1.3.6.1.4.1.2.3.51.2.2.8.6.1 | NA | deprecated | |
table · not-accessible · deprecated Table of fan pack LEDs information. This table is deprecated because the LEDs for the power modules' fans are no longer on the fan packs, the LEDs are on the power modules. See the MIB tables, componentLEDsTable and componentLEDsDetailsTable, for the power modules' LEDs. NOTE: Fan packs are also referred to as Power Module Cooling Devices. | ||||
| RfanPackLEDsEntry | 1.3.6.1.4.1.2.3.51.2.2.8.6.1.1 | NA | deprecated | |
| CledFanPackIndex | 1.3.6.1.4.1.2.3.51.2.2.8.6.1.1.1 | INTEGER (0..128) | RO | deprecated |
column · INTEGER (0..128) · read-only · deprecated Fan Pack LEDs table index. | ||||
| CledFanPackId | 1.3.6.1.4.1.2.3.51.2.2.8.6.1.1.2 | INTEGER | RO | deprecated |
column · INTEGER · read-only · deprecated The numeric fan pack ID.
| ||||
| CledFanPackExists | 1.3.6.1.4.1.2.3.51.2.2.8.6.1.1.3 | INTEGER | RO | deprecated |
column · INTEGER · read-only · deprecated Indicates whether the fan pack specified exists or not.
| ||||
| CledFanPackError | 1.3.6.1.4.1.2.3.51.2.2.8.6.1.1.4 | INTEGER | RO | deprecated |
column · INTEGER · read-only · deprecated Indicates whether the fan pack error LED is on or off.
| ||||
| NfuelGauge | 1.3.6.1.4.1.2.3.51.2.2.10 | |||
| NfuelGaugeInformation | 1.3.6.1.4.1.2.3.51.2.2.10.1 | |||
| TfuelGaugeTable | 1.3.6.1.4.1.2.3.51.2.2.10.1.1 | NA | mandatory | |
table · not-accessible · mandatory Table of Fuel Gauge information. | ||||
| RfuelGaugeEntry | 1.3.6.1.4.1.2.3.51.2.2.10.1.1.1 | NA | mandatory | |
| CfuelGaugeIndex | 1.3.6.1.4.1.2.3.51.2.2.10.1.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Fuel Gauge Table Index. | ||||
| CfuelGaugePowerDomainNumber | 1.3.6.1.4.1.2.3.51.2.2.10.1.1.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Fuel Gauge Table Power Domain Number.
| ||||
| CfuelGaugeStatus | 1.3.6.1.4.1.2.3.51.2.2.10.1.1.1.3 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Fuel Gauge Table Status for the power domain. The response will start out with a numeric value (0 = unknown, 1 = good, 2 = warning, and 3: bad), followed by a text message. | ||||
| CfuelGaugePowerModules | 1.3.6.1.4.1.2.3.51.2.2.10.1.1.1.4 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Fuel Gauge Table Power Module capacity in Watts in the power domain. | ||||
| CfuelGaugePowerManagementPolicySetting | 1.3.6.1.4.1.2.3.51.2.2.10.1.1.1.6 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Power Management Policy Setting for each power domain.
A new powerPolicyTable has been added which provides more detailed
information regarding a domains power policy information. This table
also has the capability to SET the power policy for a given domain.
Power Module Redundancy
Intended for a single power source into the chassis where each
Power Module is on its own dedicated circuit. Maximum power is
limited to one less than the number of Power Modules when more
than one Power Module is present. One Power Module can fail
without affecting compute node operation. Multiple Power Module
failures can cause the chassis to power off. Note that some compute
nodes may not be allowed to power on if doing so would exceed the
policy power limit.
Power Module Redundancy with Compute Nodes Throttling Allowed
Very similar to Power Module Redundancy. This policy allows for a
higher power limit; however, capable compute nodes may be allowed
to throttle down if one Power Module fails.
Basic Power Management
Maximum power limit is higher than other policies and is limited
only by the nameplate power of all the Power Modules combined.
This is the least conservative approach, since it does not provide
any protection for power source or Power Module failure. If any
single power supply fails, compute node and/or chassis operation
may be affected.
Power Source Redundancy
Intended for dual power sources into the chassis. Maximum power is
limited to the capacity of half the number of installed power modules.
This is the most conservative approach and is recommended when all power
modules are installed. When the chassis is correctly wired with dual
power sources, one power source can fail without affecting compute
node server operation. Note that some compute nodes may not be allowed
to power on if doing so would exceed the policy power limit.
Power Source Redundancy with Compute Node Throttling Allowed
Very similar to the Power Source Redundancy. This policy allows
for a higher power limit, however capable compute nodes may be allowed
to throttle down if one power source fails.
| ||||
| CfuelGaugeTotalPower | 1.3.6.1.4.1.2.3.51.2.2.10.1.1.1.7 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory This field displays the total available power for each power domain based on installed power modules and the current Power Management Policy Setting. | ||||
| CfuelGaugeAllocatedPower | 1.3.6.1.4.1.2.3.51.2.2.10.1.1.1.8 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory This field displays the power that has been reserved in each power domain. | ||||
| CfuelGaugeRemainingPower | 1.3.6.1.4.1.2.3.51.2.2.10.1.1.1.9 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory This field displays the remaining power available in each domain. Remaining Power = Total Power minus Power In Use | ||||
| CfuelGaugePowerInUsed | 1.3.6.1.4.1.2.3.51.2.2.10.1.1.1.10 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory This field displays the total power being used in each power domain. | ||||
| NpowerDomain1 | 1.3.6.1.4.1.2.3.51.2.2.10.2 | |||
| TpowerDomain1Table | 1.3.6.1.4.1.2.3.51.2.2.10.2.1 | NA | mandatory | |
table · not-accessible · mandatory Table of Power Domain 1. | ||||
| RpowerDomain1Entry | 1.3.6.1.4.1.2.3.51.2.2.10.2.1.1 | NA | mandatory | |
| Cpd1Index | 1.3.6.1.4.1.2.3.51.2.2.10.2.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Power Domain 1 Table Index. | ||||
| Cpd1BayNumber | 1.3.6.1.4.1.2.3.51.2.2.10.2.1.1.2 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Power Domain 1 Table Bay Number. The following Bay Number IDs are used: notApplicable(1), notApplicable(2), fanPackBay1(3), fanPackBay2(4), fanPackBay3(5), fanPackBay4(6), fanPackBay5(7), fanPackBay6(8), chassisfanBay1(9), chassisfanBay2(10), chassisfanBay3(11), chassisfanBay4(12), chassisfanBay5(13), chassisfanBay6(14), chassisfanBay7(15), chassisfanBay8(16), chassisfanBay9(17), chassisfanBay10(18), managementModuleBay1(19), managementModuleBay2(20), ioModuleBay1(21), ioModuleBay2(22), ioModuleBay3(23), ioModuleBay4(24), serverBladeBay1(25), serverBladeBay2(26), serverBladeBay3(27), serverBladeBay4(28), serverBladeBay5(29), serverBladeBay6(30), serverBladeBay7(31), serverBladeBay8(32), serverBladeBay9(33), serverBladeBay10(34), serverBladeBay11(35), serverBladeBay12(36), serverBladeBay13(37), serverBladeBay14(38), notApplicable(39) | ||||
| Cpd1BladePrimarySlot | 1.3.6.1.4.1.2.3.51.2.2.10.2.1.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Power Domain 1 Table Blade Primary Slot can be useful when a server blade spans multiple slots (e.g. double wide or triple wide). For example if the blade is double wide and is installed in slot 3 and 4. 3 is primary slot while 4 is not.
| ||||
| Cpd1ModuleStatus | 1.3.6.1.4.1.2.3.51.2.2.10.2.1.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Power Domain 1 Table Module Throttle Status.
| ||||
| Cpd1ModuleName | 1.3.6.1.4.1.2.3.51.2.2.10.2.1.1.5 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Power Domain 1 Table Module Name. | ||||
| Cpd1ModuleState | 1.3.6.1.4.1.2.3.51.2.2.10.2.1.1.6 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Power Domain 1 Table Module State.
| ||||
| Cpd1ModuleAllocatedPowerCurrent | 1.3.6.1.4.1.2.3.51.2.2.10.2.1.1.7 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Power Domain 1 Table Allocated Power Current indicates the current power allocation for the module in Watts. NOTE: When a server blade spans multiple slots (e.g. double wide or triple wide), the current power allocation for the module is equally divided among the slots. | ||||
| Cpd1ModuleAllocatedPowerMax | 1.3.6.1.4.1.2.3.51.2.2.10.2.1.1.8 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Power Domain 1 Table Allocated Power Max indicates the maximum power allocation for the module in Watts. It is indicative of the maximum amount of power the module will consume in the domain when it is fully populated with memory chips, expansion cards, etc. NOTE: When a server blade spans multiple slots (e.g. double wide or triple wide), the maximum power allocation for the module is equally divided among the slots. | ||||
| Cpd1ModuleAllocatedPowerMin | 1.3.6.1.4.1.2.3.51.2.2.10.2.1.1.9 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Power Domain 1 Table Allocated Power Min indicates the minumum power allocation for the module in Watts. It is indicative of the minumum power consumption of the component in the domain based on its maximum throttle limit. NOTE: When a server blade spans multiple slots (e.g. double wide or triple wide), the minimum power allocation for the module is equally divided among the slots. | ||||
| Cpd1ModuleCPUDutyCycles | 1.3.6.1.4.1.2.3.51.2.2.10.2.1.1.10 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Power Domain 1 Table Module CPUs Duty Cycles applies to blade servers only. It displays the duty cycle for each CPU on the blade as a percentage. Note that some blades do not report the CPU duty cycles. In this case, 'notApplicable' will be displayed. NOTE: The CPU duty cycles are reported only on a primary slot when a server blade spans multiple slots (e.g. double wide or triple wide). For example if the blade is double wide and is installed in slot 3 and 4. 3 is primary slot while 4 is not. The CPU duty cycles are reported on slot 3 while 'notApplicable' is displayed for slot 4. | ||||
| Cpd1ModuleThrottle | 1.3.6.1.4.1.2.3.51.2.2.10.2.1.1.11 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Power Domain 1 Table Module Throttle indicates whether the server blade may be allowed to throttle or not.
| ||||
| Cpd1ModulePowerCapabilities | 1.3.6.1.4.1.2.3.51.2.2.10.2.1.1.12 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Power Domain 1 Table Module Power Capabilities.
staticPowerManagement: the module with the static worst
case power values.
fixedPowermanagement: the module with the static power values but
ability to throttle.
dynamicPowerManagement: the module with power meter capability,
measurement enabled, but capping disabled.
dynamicPowerMeasurement1: the module with power meter capability,
measurement enabled, phase 1 only
dynamicPowerMeasurement2: the module with power meter capability,
measurement enabled, phase 2 or higher
dynamicPowerMeasurementWithPowerCapping: the module with power
meter capability, both measurement and capping enabled,
phase 2 or higher
| ||||
| Cpd1ModuleMeasuredOrStatic | 1.3.6.1.4.1.2.3.51.2.2.10.2.1.1.13 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Power Domain 1 Table Module Measured Or Static.
| ||||
| Cpd1TopologyPath | 1.3.6.1.4.1.2.3.51.2.2.10.2.1.1.14 | OCTET STRING (SIZE (0..100)) | RO | mandatory |
column · OCTET STRING (SIZE (0..100)) · read-only · mandatory The topology path for the component in this table. The chassis and each installed component is represented by a hardware topology tree, where each node in the tree represents a component. The path to a particular component consists of one or more <component>,<instance> pairs, where each successive pair is a child of the previous parent pair. As an example, the root of the tree is the chassis and is represented by the pair 'CHASSIS, 1'. This pair indicates the first instance of the chassis. If a blade is inserted in slot 4 of the chassis, its topology path is 'CHASSIS, 1, BLADE, 4'. With this format, the components in the chassis can be determined along with their relative hierarchy to each other. CHASSIS, 0x01 Chassis MM, 0x02 Management Module BLADE, 0x03 Main system board of a blade POWER, 0x04 Power Supply, Power Module, etc COOLING, 0x05 Fan, blower, or other cooling device IO_MODULE, 0x06 Has I/O interface, i.e. - switch or bridge MEDIA, 0x07 Media device PROCESSOR, 0x08 Any processor, processor module, etc STORAGE, 0x09 Any type of storage device EXPANSION, 0x0A Expansion Card (not covered by more specific type) MEMORY, 0x0B Any memory device, module, etc MFRU, 0x0C Managed FRU Device PANEL, 0x0D Any sort of panel device, such as a front panel BLADE_EXPANSION_MODULE, 0x0E Expansion option (BEM) such as PEU, BSE, etc CARD_EXPANSION, 0x0F Expansion card, ie. daughter card CARD_HS_EXPANSION, 0x10 High Speed Expansion card, ie. daughter card INTERPOSER, 0x11 Interposer device CLOCK, 0x12 Clock card MUX, 0x13 Mulitplexer card ADDIN, 0x14 cKVM card & other addin cards STORAGE_MODULE, 0x15 Container of one or more Storage Devices SYS_EXPANSION_CARD, 0x16 Management card BATTERY, 0x17 A single battery BATTERY_MODULE, 0x18 Container of one or more batteries REAR_LED, 0x19 Rear LED card MEMORY_BANK, 0x1A Memory banks AIR_FILTER, 0x1B Filter mechanism (bezel) SERIAL_PORT_MODULE, 0x1C Container of one or more serial ports PARENT, 0x1D Reference to parent for multi-parent support PHY_PORT, 0x1E Physical port IO_EXPANDER, 0x1F RAID card CABLE, 0x20 Cable/Interconnect FAN_MUX 0x29 Fan multiplexer card PCI_EXPRESS, 0x32 PCI express card on (PEN) FLASH_DIMM, 0x33 Used for SPD devices that matches the silkscreen of the DIMM slot RACK, 0x50 Rack PLATFORM, 0x51 Generic Platform like rack mounted server/appliance DATAPLEX, 0x52 DataPlex OTHER, 0x53 Other unknown etc. PERIPHERAL_MODULE, 0x54 SYSTEM_BOARD, 0x55 System board PROCESSOR_MODULE, 0x56 BACK_PANEL, 0x57 POWER_SYSTEM_BOARD, 0x58 STORAGE_BACKPLANE, 0x59 Drive back plane PROC_BOARD, 0x5A Holds 1 or more processors POWER_DI, 0x5B Power mgt / power distribution board CHASSIS_BACK_PANEL, 0x5C SUB_CHASSIS, 0x5D OTHER_CHASSIS_BOARD, 0x5E DEVICE_MODULE, 0x5F REMOTE_DEVICE, 0x60 Remote mgt communication device EXTERNAL_ENVIRONMENT, 0x61 Such as external temp sensor for outside box temps PROC_MEMORY_MODULE, 0x62 Processors and memory on same module | ||||
| NpowerDomain1PowerTrending | 1.3.6.1.4.1.2.3.51.2.2.10.2.3 | |||
| Spd1PowerTrendingPeriod | 1.3.6.1.4.1.2.3.51.2.2.10.2.3.1 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Specify time period for power domain 1 power trending information table view. NOTE: This time period should be configured before displaying the following Power Trending Information table for Power Domain.
| ||||
| Tpd1PowerTrendingSampleTable | 1.3.6.1.4.1.2.3.51.2.2.10.2.3.10 | NA | mandatory | |
table · not-accessible · mandatory Table of Power Domain 1 Power Trending Information. | ||||
| Rpd1PowerTrendingSampleEntry | 1.3.6.1.4.1.2.3.51.2.2.10.2.3.10.1 | NA | mandatory | |
row · not-accessible · mandatory Power Domain 1 Power Trending Sample entry. | ||||
| Cpd1PowerTrendingSampleIndex | 1.3.6.1.4.1.2.3.51.2.2.10.2.3.10.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Power Domain 1 Power Trending Sample Table Index. | ||||
| Cpd1PowerTrendingSampleTimeStamp | 1.3.6.1.4.1.2.3.51.2.2.10.2.3.10.1.2 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Power Domain 1 Power Trending Sample Table Timestamp. | ||||
| Cpd1PowerTrendingSampleAve | 1.3.6.1.4.1.2.3.51.2.2.10.2.3.10.1.3 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Power Domain 1 Power Trending Table Average Power. | ||||
| NmoduleInformation | 1.3.6.1.4.1.2.3.51.2.2.10.4 | |||
| NbladeDetails | 1.3.6.1.4.1.2.3.51.2.2.10.4.1 | |||
| TbladeDetailsTable | 1.3.6.1.4.1.2.3.51.2.2.10.4.1.1 | NA | mandatory | |
table · not-accessible · mandatory Table of Blade Module Details. | ||||
| RbladeDetailsEntry | 1.3.6.1.4.1.2.3.51.2.2.10.4.1.1.1 | NA | mandatory | |
| CbladeDetailsIndex | 1.3.6.1.4.1.2.3.51.2.2.10.4.1.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Blade Module Details Table Index. | ||||
| CbladeDetailsId | 1.3.6.1.4.1.2.3.51.2.2.10.4.1.1.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Blade Module Details Table Blade Id.
| ||||
| CbladeDetailsMaxPowerConfig | 1.3.6.1.4.1.2.3.51.2.2.10.4.1.1.1.3 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Blade Module Details Table Maximum Power Configuration. Allow the user to set the maximum power that can be used by the blade. This function is also known as power capping. Blade must be powered on to set this value. If the value of maximum power config is zero, it means the blade doesn't support the power capping feature | ||||
| CbladeDetailsEffectiveClockRate | 1.3.6.1.4.1.2.3.51.2.2.10.4.1.1.1.4 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade Module Details Table Effective CPU Clock Rate applies to DPM blades only. It displays processor's effective clock rate based on sample interval. Note that some blades do not effective clock rate. In this case, 'notApplicable' will be displayed. NOTE: The effective clock rate are reported only on a primary slot when a server blade spans multiple slots (e.g. double wide or triple wide). For example if the blade is double wide and is installed in slot 3 and 4. 3 is primary slot while 4 is not. The effective clock rate are reported on slot 3 while 'notApplicable' is displayed for slot 4. | ||||
| CbladeDetailsMaximumClockRate | 1.3.6.1.4.1.2.3.51.2.2.10.4.1.1.1.5 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade Module Details Table Maximum CPU Clock Rate applies to DPM blades only. It displays processor's maximum clock rate based on sample interval. Note that some blades do not maximum clock rate. In this case, 'notApplicable' will be displayed. NOTE: The maximum clock rate are reported only on a primary slot when a server blade spans multiple slots (e.g. double wide or triple wide). For example if the blade is double wide and is installed in slot 3 and 4. 3 is primary slot while 4 is not. The maximum clock rate are reported on slot 3 while 'notApplicable' is displayed for slot 4. | ||||
| CbladeDetailsPowerSaverMode | 1.3.6.1.4.1.2.3.51.2.2.10.4.1.1.1.6 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory When enabled, the static low power saver mode allows the blade to selectively alter its operating voltage and frequency to reduce power consumption. This feature is not available on all blade types. Please refer to the blade documentation for details. If a blade does not support the static low power saver mode, this object will return notApplicable (255). Under certain rare circumstances, the enabling of the static low power saver mode may not complete successfully due to interactions with other blade functions, such as BIOS. Therefore, it is highly recommended that the user perform a GET of this object after performing a SET, in order to verify the completion of the intended operation. NOTE: enabling this object will disable bladeDetailsDynamicPowerSaver if its not already disabled.
| ||||
| CbladeDetailsDynamicPowerSaver | 1.3.6.1.4.1.2.3.51.2.2.10.4.1.1.1.7 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory When enabled, Dynamic Power Saver allows the voltage and frequency of the CPUs on the blade to be controlled based on how busy the CPU is. This feature is not available on all blade types. Please refer to the blade documentation for details. If a blade does not support the dynamic power saver, this object will return notApplicable (255). Under certain rare circumstances, the enabling of the dynamic power saver may not complete successfully due to interactions with other blade functions, such as BIOS. Therefore, it is highly recommended that the user perform a GET of this object after performing a SET, in order to verify the completion of the intended operation. NOTE: enabling this object will disable bladeDetailsPowerSaverMode if its not already disabled.
| ||||
| CbladeDetailsDynamicPowerFavorPerformanceOverPower | 1.3.6.1.4.1.2.3.51.2.2.10.4.1.1.1.8 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory When enabled, Dynamic Power Favor Performance Over Power supports a max performance mode that pushes the system past its nominal CPU frequency when CPU and memory utilization implies it would help and the system allows it. Dynamic Power Performance Over Power can be active on the blade only after Dynamic Power Saver is enabled. This feature is not available on all blade types. Please refer to the blade documentation for details. If a blade does not support the dynamic power saver, this object will return notApplicable (255). Under certain rare circumstances, the enabling of the dynamic power favor performance over power may not complete successfully due to interactions with other blade functions, such as BIOS. Therefore, it is highly recommended that the user perform a GET of this object after performing a SET, in order to verify the completion of the intended operation.
| ||||
| CbladeDetailsPowerControl | 1.3.6.1.4.1.2.3.51.2.2.10.4.1.1.1.9 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory This object is used to get or set the power control setting on a blade. If dynamic power mgmt is not supported on a blade, notApplicable(255) will be returned. This will set the power control setting on all slots of the multiwide blade. The same can be used if the blade is single wide.
| ||||
| CbladeDetailsPcapMin | 1.3.6.1.4.1.2.3.51.2.2.10.4.1.1.1.10 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade Module Details Table power capping Minimum value in watts. The blade must support the advanced power management feature. If the value of Pcap Min is 'notApplicable', it means the blade doesn't support the power capping feature. If the value of Pcap Min is 'notAvailable', it means the data could not be obtained. | ||||
| CbladeDetailsPcapGuaranteedMin | 1.3.6.1.4.1.2.3.51.2.2.10.4.1.1.1.11 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade Module Details Table power capping Guaranteed Minimum value in watts. The blade must support the advanced power management feature. If the value of Pcap Guaranteed Min is 'notApplicable', it means the blade doesn't support the power capping feature. If the value of Pcap GuaranteedMin is 'notAvailable', it means the data could not be obtained. | ||||
| CbladeDetailsPcapMax | 1.3.6.1.4.1.2.3.51.2.2.10.4.1.1.1.12 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade Module Details Table power capping Maximum value in watts. The blade must support the advanced power management feature. If the value is '<max1> Watts,<max2> Watts', which means, - if bladeDetailsDynamicPowerSaver is enabled, it is <max2> - otherwise it is <max1> If the value of Pcap Max is 'notApplicable', it means the blade doesn't support the power capping feature. If the value of Pcap Min is 'notAvailable', it means the data could not be obtained. | ||||
| NbladePowerTrending | 1.3.6.1.4.1.2.3.51.2.2.10.4.1.3 | |||
| SbladePowerTrendingPeriod | 1.3.6.1.4.1.2.3.51.2.2.10.4.1.3.1 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Specify time period for blade module power trending information table view. NOTE: This time period should be configured before displaying the following Power Trending Information table for Blade Module. Since the power trending data is constantly being computed and saved in the management application database, some queries of the bladePowerTrendingSampleTable may not provide information for a very short window of time. If the table returns empty, please wait a short period and retry the query.
| ||||
| SbladePowerTrendingBladeId | 1.3.6.1.4.1.2.3.51.2.2.10.4.1.3.2 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Blade Module Power Trending Blade Id. NOTE: The Blade Id should be configured before displaying the bladePowerTrendingTable.
| ||||
| SbladePowerTrendingTopologyPath | 1.3.6.1.4.1.2.3.51.2.2.10.4.1.3.3 | OCTET STRING (SIZE (0..100)) | RW | mandatory |
scalar · OCTET STRING (SIZE (0..100)) · read-write · mandatory The topology Path is a location identifier for a blade. The chassis and each installed blade is represented by a hardware topology tree, where each node in the tree represents a blade. The path to a particular blade consists of one or more <blade>,<instance> pairs, where each successive pair is a child of the previous parent pair. This topology path is used to identify blades such as blade storage devices. Some examples. A storage blade with a controller card plugged into slot 1 topology location would be represented as : 010103010301--> Storage Controller card #1 of Sub-Chassis #1 A storage blade with a controller card plugged into slot 2 topology location would be represented as : 010103010302--> Storage Controller card #2 of Sub-Chassis #1 | ||||
| TbladePowerTrendingSampleTable | 1.3.6.1.4.1.2.3.51.2.2.10.4.1.3.10 | NA | mandatory | |
table · not-accessible · mandatory Table of Blade Module Power Trending Information. Since the power trending data is constantly being computed and saved in the management application database, some queries of this table may not provide information for a very short window of time. If the table data returns empty,please wait a short period and retry the query. | ||||
| RbladePowerTrendingSampleEntry | 1.3.6.1.4.1.2.3.51.2.2.10.4.1.3.10.1 | NA | mandatory | |
row · not-accessible · mandatory Blade Module Power Trending Sample entry. | ||||
| CbladePowerTrendingSampleIndex | 1.3.6.1.4.1.2.3.51.2.2.10.4.1.3.10.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Blade Module Power Trending Sample Table Index. | ||||
| CbladePowerTrendingSampleId | 1.3.6.1.4.1.2.3.51.2.2.10.4.1.3.10.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Blade Module Power Trending Sample Table Blade Id. If the blade is defined using a topology location by using the scalar bladePowerTrendingTopologyPath, a zero will be displayed in the bladePowerTrendingSampleId.
| ||||
| CbladePowerTrendingSampleTimeStamp | 1.3.6.1.4.1.2.3.51.2.2.10.4.1.3.10.1.3 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade Module Power Trending Sample Table Timestamp. | ||||
| CbladePowerTrendingSampleMax | 1.3.6.1.4.1.2.3.51.2.2.10.4.1.3.10.1.4 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade Module Power Trending Sample Table Maximum Power. | ||||
| CbladePowerTrendingSampleMin | 1.3.6.1.4.1.2.3.51.2.2.10.4.1.3.10.1.5 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade Module Power Trending Sample Table Minimum Power. | ||||
| CbladePowerTrendingSampleAve | 1.3.6.1.4.1.2.3.51.2.2.10.4.1.3.10.1.6 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade Module Power Trending Sample Table Average Power. | ||||
| CbladePowerTrendingSampleTopologyId | 1.3.6.1.4.1.2.3.51.2.2.10.4.1.3.10.1.7 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade module topology path. This field will have a topology location when a blade is a storage blade or a blade defined with a sub chassis. If the blade is defined with a primary slot location by using the scalar bladePowerTrendingBladeId, 'not applicable' will be displayed in the bladePowerTrendingSampleTopologyId. | ||||
| NswitchDetails | 1.3.6.1.4.1.2.3.51.2.2.10.4.2 | |||
| NswitchPowerTrending | 1.3.6.1.4.1.2.3.51.2.2.10.4.2.3 | |||
| SswitchPowerTrendingPeriod | 1.3.6.1.4.1.2.3.51.2.2.10.4.2.3.1 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Specify time period for switch module power trending information table view. NOTE: This time period should be configured before displaying the following Power Trending Information table for Switch Module.
| ||||
| SswitchPowerTrendingSwitchId | 1.3.6.1.4.1.2.3.51.2.2.10.4.2.3.2 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Switch Module Power Trending Switch Id. NOTE: The Switch Id should be configured before displaying the switchPowerTrendingTable.
| ||||
| TswitchPowerTrendingSampleTable | 1.3.6.1.4.1.2.3.51.2.2.10.4.2.3.10 | NA | mandatory | |
table · not-accessible · mandatory Table of Switch Module Power Trending Information. | ||||
| RswitchPowerTrendingSampleEntry | 1.3.6.1.4.1.2.3.51.2.2.10.4.2.3.10.1 | NA | mandatory | |
row · not-accessible · mandatory Switch Module Power Trending Sample entry. | ||||
| CswitchPowerTrendingSampleIndex | 1.3.6.1.4.1.2.3.51.2.2.10.4.2.3.10.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Switch Module Power Trending Sample Table Index. | ||||
| CswitchPowerTrendingSampleId | 1.3.6.1.4.1.2.3.51.2.2.10.4.2.3.10.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Switch Module Power Trending Sample Table Switch Id.
| ||||
| CswitchPowerTrendingSampleTimeStamp | 1.3.6.1.4.1.2.3.51.2.2.10.4.2.3.10.1.3 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Switch Module Power Trending Sample Table Timestamp. | ||||
| CswitchPowerTrendingSampleMax | 1.3.6.1.4.1.2.3.51.2.2.10.4.2.3.10.1.4 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Switch Module Power Trending Sample Table Maximum Power. | ||||
| CswitchPowerTrendingSampleMin | 1.3.6.1.4.1.2.3.51.2.2.10.4.2.3.10.1.5 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Switch Module Power Trending Sample Table Minimum Power. | ||||
| CswitchPowerTrendingSampleAve | 1.3.6.1.4.1.2.3.51.2.2.10.4.2.3.10.1.6 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Switch Module Power Trending Sample Table Average Power. | ||||
| NchassisFanDetails | 1.3.6.1.4.1.2.3.51.2.2.10.4.3 | |||
| NchassisFanPowerTrending | 1.3.6.1.4.1.2.3.51.2.2.10.4.3.3 | |||
| SchassisFanPowerTrendingPeriod | 1.3.6.1.4.1.2.3.51.2.2.10.4.3.3.1 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Specify time period for chassis fan module power trending information table view. NOTE: This time period should be configured before displaying the following Power Trending Information table for chassis fan module.
| ||||
| SchassisFanPowerTrendingId | 1.3.6.1.4.1.2.3.51.2.2.10.4.3.3.2 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Chass fan mModule power trending fan ID. NOTE: The ID should be configured before displaying the chassisFanPowerTrendingTable.
| ||||
| TchassisFanPowerTrendingSampleTable | 1.3.6.1.4.1.2.3.51.2.2.10.4.3.3.10 | NA | mandatory | |
table · not-accessible · mandatory Table of chassis fan Module Power Trending Information. | ||||
| RchassisFanPowerTrendingSampleEntry | 1.3.6.1.4.1.2.3.51.2.2.10.4.3.3.10.1 | NA | mandatory | |
row · not-accessible · mandatory Chassis fan Module Power Trending Sample entry. | ||||
| CchassisFanPowerTrendingSampleIndex | 1.3.6.1.4.1.2.3.51.2.2.10.4.3.3.10.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Chassis fan Module Power Trending Sample Table Index. | ||||
| CchassisFanPowerTrendingSampleId | 1.3.6.1.4.1.2.3.51.2.2.10.4.3.3.10.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Chassis fan Module Power Trending Sample Table Id.
| ||||
| CchassisFanPowerTrendingSampleTimeStamp | 1.3.6.1.4.1.2.3.51.2.2.10.4.3.3.10.1.3 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Chassis fan Module Power Trending Sample Table Timestamp. | ||||
| CchassisFanPowerTrendingSampleMax | 1.3.6.1.4.1.2.3.51.2.2.10.4.3.3.10.1.4 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Chassis fan Module Power Trending Sample Table Maximum Power. | ||||
| CchassisFanPowerTrendingSampleMin | 1.3.6.1.4.1.2.3.51.2.2.10.4.3.3.10.1.5 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Chassis fan Module Power Trending Sample Table Minimum Power. | ||||
| CchassisFanPowerTrendingSampleAve | 1.3.6.1.4.1.2.3.51.2.2.10.4.3.3.10.1.6 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Chassis fan Module Power Trending Sample Table Average Power. | ||||
| NchassisInformation | 1.3.6.1.4.1.2.3.51.2.2.10.5 | |||
| NchassisConfiguration | 1.3.6.1.4.1.2.3.51.2.2.10.5.1 | |||
| SchassisTotalDCPowerAvailable | 1.3.6.1.4.1.2.3.51.2.2.10.5.1.1 | OCTET STRING | RO | mandatory |
scalar · OCTET STRING · read-only · mandatory Chassis total DC power available, which displays the total DC power available for the entire chassis. It is the sum of the two power domains. | ||||
| SchassisTotalPowerInUsed | 1.3.6.1.4.1.2.3.51.2.2.10.5.1.2 | OCTET STRING | RO | mandatory |
scalar · OCTET STRING · read-only · mandatory Chassis total power being used, which displays the total power being consumed by all modules in the chassis. It also includes power consumed by the blowers (chassis cooling devices) for the chassis. | ||||
| SchassisTotalThermalOutput | 1.3.6.1.4.1.2.3.51.2.2.10.5.1.3 | OCTET STRING | RO | mandatory |
scalar · OCTET STRING · read-only · mandatory Chassis total thermal output, which displays the thermal output (load) in BTUs per hour. It is calculated based on the total input power in use. (1 Watt = 3.412 BTU/hour). | ||||
| SchassisPowerService | 1.3.6.1.4.1.2.3.51.2.2.10.5.1.5 | INTEGER | RO | deprecated |
scalar · INTEGER · read-only · deprecated The chassis power service mode. NOTE: This MIB object is for BCS only. This object has been deprecated. See the object, powerModuleDescription, for similar information.
| ||||
| NchassisPowerTrending | 1.3.6.1.4.1.2.3.51.2.2.10.5.3 | |||
| SchassisPowerTrendingPeriod | 1.3.6.1.4.1.2.3.51.2.2.10.5.3.1 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Specify time period of power trending information. NOTE: This time period should be configured before displaying the following Power Trending Information table for Chassis.
| ||||
| TchassisPowerTrendingSampleTable | 1.3.6.1.4.1.2.3.51.2.2.10.5.3.10 | NA | mandatory | |
table · not-accessible · mandatory Table of Chassis Power Trending Sample Information in specified time period. | ||||
| RchassisPowerTrendingSampleEntry | 1.3.6.1.4.1.2.3.51.2.2.10.5.3.10.1 | NA | mandatory | |
row · not-accessible · mandatory Chassis Power Trending Sample entry in specified time period. | ||||
| CchassisPowerTrendingSampleIndex | 1.3.6.1.4.1.2.3.51.2.2.10.5.3.10.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Chassis Power Trending Sample Index in specified time period. | ||||
| CchassisPowerTrendingSampleTimeStamp | 1.3.6.1.4.1.2.3.51.2.2.10.5.3.10.1.2 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Chassis Power Trending Sample Timestamp in specified time period. | ||||
| CchassisPowerTrendingSampleAve | 1.3.6.1.4.1.2.3.51.2.2.10.5.3.10.1.3 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Chassis Power Trending Sample Average Power in specified time period. | ||||
| NchassisThermalTrending | 1.3.6.1.4.1.2.3.51.2.2.10.5.5 | |||
| SchassisThermalTrendingPeriod | 1.3.6.1.4.1.2.3.51.2.2.10.5.5.1 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Specify time period of thermal trending information. NOTE: This time period should be configured before displaying the following Thermal Trending Information table for Chassis.
| ||||
| TrearLEDCardThermalTrendingTable | 1.3.6.1.4.1.2.3.51.2.2.10.5.5.10 | NA | mandatory | |
table · not-accessible · mandatory Table of rear LED card Thermal Trending Information. | ||||
| RrearLEDCardThermalTrendingEntry | 1.3.6.1.4.1.2.3.51.2.2.10.5.5.10.1 | NA | mandatory | |
row · not-accessible · mandatory Rear LED Card Thermal Trending entry. | ||||
| CrearLEDCardThermalTrendingIndex | 1.3.6.1.4.1.2.3.51.2.2.10.5.5.10.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Rear LED Card Thermal Trending Table Index. | ||||
| CrearLEDCardThermalTrendingTimeStamp | 1.3.6.1.4.1.2.3.51.2.2.10.5.5.10.1.2 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Rear LED Card Thermal Trending Table Sample Timestamp. | ||||
| CrearLEDCardThermalTrendingTemperatureAvg | 1.3.6.1.4.1.2.3.51.2.2.10.5.5.10.1.3 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Rear LED Card Thermal Trending Table Average Temperature. | ||||
| CrearLEDCardThermalTrendingTemperatureMin | 1.3.6.1.4.1.2.3.51.2.2.10.5.5.10.1.4 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Rear LED Card Thermal Trending Table Minumum Temperature. | ||||
| CrearLEDCardThermalTrendingTemperatureMax | 1.3.6.1.4.1.2.3.51.2.2.10.5.5.10.1.5 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Rear LED Card Thermal Trending Table Maximum Temperature. | ||||
| TcfmThermalTrendingTable | 1.3.6.1.4.1.2.3.51.2.2.10.5.5.60 | NA | mandatory | |
table · not-accessible · mandatory Table of Cubic Feet per Minute Thermal Trending Information. | ||||
| RcfmThermalTrendingEntry | 1.3.6.1.4.1.2.3.51.2.2.10.5.5.60.1 | NA | mandatory | |
| CcfmThermalTrendingIndex | 1.3.6.1.4.1.2.3.51.2.2.10.5.5.60.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Cubic Feet per Minute Thermal Trending Table Index. | ||||
| CcfmThermalTrendingTimeStamp | 1.3.6.1.4.1.2.3.51.2.2.10.5.5.60.1.2 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Cubic Feet per Minute Thermal Trending Table Sample Timestamp. | ||||
| CcfmThermalTrendingCurrentCFM | 1.3.6.1.4.1.2.3.51.2.2.10.5.5.60.1.3 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Cubic Feet per Minute Thermal Trending Table The Current CFM of air flow calculated at this sample time. | ||||
| CcfmThermalTrendingMaxCFM | 1.3.6.1.4.1.2.3.51.2.2.10.5.5.60.1.4 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Cubic Feet per Minute Thermal Trending Table The Maximum CFM of air flow the chassis can provide at this sample time. | ||||
| TehiThermalTrendingTable | 1.3.6.1.4.1.2.3.51.2.2.10.5.5.70 | NA | mandatory | |
table · not-accessible · mandatory Table of Exhaust Heat Index Thermal Trending Information. | ||||
| RehiThermalTrendingEntry | 1.3.6.1.4.1.2.3.51.2.2.10.5.5.70.1 | NA | mandatory | |
row · not-accessible · mandatory Chassis Exhaust Heat Index Thermal Trending entry. | ||||
| CehiThermalTrendingIndex | 1.3.6.1.4.1.2.3.51.2.2.10.5.5.70.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Exhaust Heat Index Thermal Trending Table Index. | ||||
| CehiThermalTrendingTimeStamp | 1.3.6.1.4.1.2.3.51.2.2.10.5.5.70.1.2 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Chassis Exhaust Heat Index Thermal Trending Table Sample Timestamp. | ||||
| CehiThermalTrendingMinEHI | 1.3.6.1.4.1.2.3.51.2.2.10.5.5.70.1.3 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Chassis Exhaust Heat Index Thermal Trending Table Minimum Exhaust Heat Index since last reboot. | ||||
| CehiThermalTrendingMaxEHI | 1.3.6.1.4.1.2.3.51.2.2.10.5.5.70.1.4 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Chassis Exhaust Heat Index Thermal Trending Table Maximum Exhaust Heat Index since last reboot. | ||||
| CehiThermalTrendingAvgEHI | 1.3.6.1.4.1.2.3.51.2.2.10.5.5.70.1.5 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Chassis Exhaust Heat Index Thermal Trending Table Average of last 2 Exhaust Heat Index calculations since last reboot. | ||||
| NpowerPolicyInformation | 1.3.6.1.4.1.2.3.51.2.2.10.6 | |||
| TpowerPolicyTable | 1.3.6.1.4.1.2.3.51.2.2.10.6.1 | NA | mandatory | |
table · not-accessible · mandatory Table of Power Policy information for all power domains. Reading this table can tell you about the available power policies that can be configured for a domain and also which is currently selected. The powerPolicyActivate object can also be SET to select which policy should be active for a given power domain. | ||||
| RpowerPolicyEntry | 1.3.6.1.4.1.2.3.51.2.2.10.6.1.1 | NA | mandatory | |
| CpowerPolicyIndex | 1.3.6.1.4.1.2.3.51.2.2.10.6.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The unique idenitifier of a row in the powerPolicyTable. | ||||
| CpowerPolicyPowerDomainNumber | 1.3.6.1.4.1.2.3.51.2.2.10.6.1.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The power domain number which this row is associated with.
| ||||
| CpowerPolicyName | 1.3.6.1.4.1.2.3.51.2.2.10.6.1.1.3 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The short name of the power policy. The following are the possible
names and their detailed description:
Power Module Redundancy
Intended for a single power source into the chassis
where each Power Module is on its own dedicated circuit.
Total allowed power draw is limited to one less than the
number of Power Modules when more than one Power Module is
present. One Power Module can fail without affecting blade
operation. Multiple Power Module failures can cause
the chassis to power off. Note that some blades may not be
allowed to power on if doing so would exceed the policy power
limit.
Power Module Redundancy with Blade Throttling Allowed
Very similar to the Power Module Redundancy policy. This
policy allows you to draw more total power; however, capable
blades may be allowed to throttle down if one Power Module fails.
Basic Power Management
Total allowed power is higher than other policies and is limited only
by the total power capacity of all the Power Modules up to the maximum
of chassis power rating. This is the least conservative approach, since
it does not provide any protection for power source or Power Module
failure. If any single power supply fails, blade and/or chassis
operation may be affected.
Power Source Redundancy
Intended for dual power sources into the chassis. Total
allowed power draw is limited to the capacity of two Power
Modules. This is the most conservative approach and is
recommended when all four Power Modules are installed.
When the chassis is correctly wired with dual power
sources, one power source can fail without affecting
blade operation. Note that some blades may not be
allowed to power on if doing so would exceed the policy
power limit.
Power Source Redundancy with Blade Throttling Allowed
Very similar to the Power Source Redundancy policy. This policy
allows you to draw more total power; however, capable blades
may be allowed to throttle down if one power source fails. | ||||
| CpowerPolicyPwrSupplyFailureLimit | 1.3.6.1.4.1.2.3.51.2.2.10.6.1.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The maximum number of power supplies that can fail in a chassis while still providing redundancy. | ||||
| CpowerPolicyMaxPowerLimit | 1.3.6.1.4.1.2.3.51.2.2.10.6.1.1.5 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The maximum power available (in watts), based on the number of power modules and the Power Management Policy setting. | ||||
| CpowerPolicyEstimatedUtilization | 1.3.6.1.4.1.2.3.51.2.2.10.6.1.1.6 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The estimated utilization (as a percentage) based on current power usage. | ||||
| CpowerPolicyActivate | 1.3.6.1.4.1.2.3.51.2.2.10.6.1.1.7 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory When read, this object provides the status of this power policy. If the value is enabled(1), it means this is the active power policy for the associated domain. When set to a value of enabled(1), the power policy will be made the active one for the associated domain. A set of disabled(0) is not allowed. The SET may fail when the user goes from a less restrictive policy to a more restrictive policy, e.g. no power management to redundant power modules. This happens because the MM might have allocated more power for components in the less restrictive policy. Then if a user wants to go to a more restrictive policy, the power available may be lower than what was already allocated. The SET should always succeed if a user goes from a more restrictive to a less restrictive policy.
| ||||
| Nusers | 1.3.6.1.4.1.2.3.51.2.2.17 | |||
| NmmUsers | 1.3.6.1.4.1.2.3.51.2.2.17.1 | |||
| TcurrentlyLoggedInTable | 1.3.6.1.4.1.2.3.51.2.2.17.1.1 | NA | mandatory | |
table · not-accessible · mandatory Table of MM users currently logged in. | ||||
| RcurrentlyLoggedInEntry | 1.3.6.1.4.1.2.3.51.2.2.17.1.1.1 | NA | mandatory | |
row · not-accessible · mandatory MM users currently logged in entries. | ||||
| CcurrentlyLoggedInEntryIndex | 1.3.6.1.4.1.2.3.51.2.2.17.1.1.1.1 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Index for MM users currently logged in. | ||||
| CcurrentlyLoggedInEntryUserId | 1.3.6.1.4.1.2.3.51.2.2.17.1.1.1.2 | OCTET STRING (SIZE (0..64)) | RO | mandatory |
column · OCTET STRING (SIZE (0..64)) · read-only · mandatory Name for MM users currently logged in. NOTE: 'Default SNMPv1 user' indicates an internal user used by SNMPv1 agent. | ||||
| CcurrentlyLoggedInEntryAccMethod | 1.3.6.1.4.1.2.3.51.2.2.17.1.1.1.3 | OCTET STRING (SIZE (0..32)) | RO | mandatory |
column · OCTET STRING (SIZE (0..32)) · read-only · mandatory Access method for MM users currently logged in. | ||||
| NvpdInformation | 1.3.6.1.4.1.2.3.51.2.2.21 | |||
| NchassisInfoVpd | 1.3.6.1.4.1.2.3.51.2.2.21.1 | |||
| NchassisVpd | 1.3.6.1.4.1.2.3.51.2.2.21.1.1 | |||
| SchassisVpdMachineType | 1.3.6.1.4.1.2.3.51.2.2.21.1.1.1 | OCTET STRING | RW | deprecated |
scalar · OCTET STRING · read-write · deprecated Machine type VPD information (from System BIOS). This field must be four alpha numeric characters. | ||||
| SchassisVpdMachineModel | 1.3.6.1.4.1.2.3.51.2.2.21.1.1.2 | OCTET STRING | RW | deprecated |
scalar · OCTET STRING · read-write · deprecated Machine model VPD information (from System BIOS). This field must be three alpha numeric characters. | ||||
| SchassisSerialNumber | 1.3.6.1.4.1.2.3.51.2.2.21.1.1.3 | OCTET STRING | RW | deprecated |
scalar · OCTET STRING · read-write · deprecated Machine serial number VPD information (from System BIOS). This field must be seven alpha numeric characters. | ||||
| SchassisUUID | 1.3.6.1.4.1.2.3.51.2.2.21.1.1.4 | OCTET STRING | RW | deprecated |
scalar · OCTET STRING · read-write · deprecated Machine UUID (Universal Unique ID information) (from System BIOS). This field must be 32 alpha numeric characters. | ||||
| SchassisManufacturingId | 1.3.6.1.4.1.2.3.51.2.2.21.1.1.5 | OCTET STRING | RO | deprecated |
scalar · OCTET STRING · read-only · deprecated Machine chassis manufacturing ID. | ||||
| SchassisHardwareRevision | 1.3.6.1.4.1.2.3.51.2.2.21.1.1.6 | INTEGER | RO | deprecated |
scalar · INTEGER · read-only · deprecated Machine chassis hardware revision. If a hardware revision is programmed in the OEM VPD area for this component, then the HardwareRevisionString version of this MIB object should be used. | ||||
| SchassisFruNumber | 1.3.6.1.4.1.2.3.51.2.2.21.1.1.7 | OCTET STRING | RO | deprecated |
scalar · OCTET STRING · read-only · deprecated Machine chassis FRU number. | ||||
| SchassisManufDate | 1.3.6.1.4.1.2.3.51.2.2.21.1.1.8 | OCTET STRING | RO | deprecated |
scalar · OCTET STRING · read-only · deprecated Machine chassis manufacture date. | ||||
| SchassisPartNumber | 1.3.6.1.4.1.2.3.51.2.2.21.1.1.9 | OCTET STRING | RO | deprecated |
scalar · OCTET STRING · read-only · deprecated Machine chassis part number. | ||||
| SchassisFruSerial | 1.3.6.1.4.1.2.3.51.2.2.21.1.1.10 | OCTET STRING | RO | deprecated |
scalar · OCTET STRING · read-only · deprecated Machine chassis FRU serial number. | ||||
| SchassisManufacturingIDNumber | 1.3.6.1.4.1.2.3.51.2.2.21.1.1.11 | OCTET STRING | RO | deprecated |
scalar · OCTET STRING · read-only · deprecated Machine chassis manufacturer ID Number. | ||||
| SchassisProductId | 1.3.6.1.4.1.2.3.51.2.2.21.1.1.12 | OCTET STRING | RO | deprecated |
scalar · OCTET STRING · read-only · deprecated Machine chassis product ID. | ||||
| SchassisSubManufacturerId | 1.3.6.1.4.1.2.3.51.2.2.21.1.1.13 | OCTET STRING | RO | deprecated |
scalar · OCTET STRING · read-only · deprecated Machine chassis subsystem manufacturer. | ||||
| SchassisClei | 1.3.6.1.4.1.2.3.51.2.2.21.1.1.14 | OCTET STRING | RO | deprecated |
scalar · OCTET STRING · read-only · deprecated Machine chassis Common Language Equipment Identification (CLEI). | ||||
| SchassisHardwareRevisionString | 1.3.6.1.4.1.2.3.51.2.2.21.1.1.16 | OCTET STRING | RO | deprecated |
scalar · OCTET STRING · read-only · deprecated Machine chassis hardware revision in string format. If a hardware revision is programmed in the OEM VPD area for this component, then this MIB object should be used. | ||||
| NmmHardwareVpd | 1.3.6.1.4.1.2.3.51.2.2.21.2 | |||
| TmmHardwareVpdTable | 1.3.6.1.4.1.2.3.51.2.2.21.2.1 | NA | deprecated | |
table · not-accessible · deprecated Table of the management module hardware components. For consistent results, view as a table and not as individual entries. | ||||
| RmmHardwareVpdEntry | 1.3.6.1.4.1.2.3.51.2.2.21.2.1.1 | NA | deprecated | |
row · not-accessible · deprecated Management module hardware VPD entry. For consistent results, view as a table and not as individual entries.
| ||||
| CmmHardwareVpdIndex | 1.3.6.1.4.1.2.3.51.2.2.21.2.1.1.1 | INTEGER | RO | deprecated |
column · INTEGER · read-only · deprecated Management module hardware VPD index. For consistent results, view as a table and not as individual entries. | ||||
| CmmHardwareVpdBayNumber | 1.3.6.1.4.1.2.3.51.2.2.21.2.1.1.2 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Management module hardware VPD Bay number. For consistent results, view as a table and not as individual entries. | ||||
| CmmHardwareVpdManufacturingId | 1.3.6.1.4.1.2.3.51.2.2.21.2.1.1.3 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Management module hardware VPD manufacturing ID. For consistent results, view as a table and not as individual entries. | ||||
| CmmHardwareVpdFruNumber | 1.3.6.1.4.1.2.3.51.2.2.21.2.1.1.4 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Management module hardware VPD FRU number. For consistent results, view as a table and not as individual entries. | ||||
| CmmHardwareVpdHardwareRevision | 1.3.6.1.4.1.2.3.51.2.2.21.2.1.1.5 | INTEGER | RO | deprecated |
column · INTEGER · read-only · deprecated Management module hardware VPD hardware revision. For consistent results, view as a table and not as individual entries. If a hardware revision is programmed in the OEM VPD area for this component, then the HardwareRevisionString version of this MIB object should be used. | ||||
| CmmHardwareVpdUuid | 1.3.6.1.4.1.2.3.51.2.2.21.2.1.1.6 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Management module hardware VPD UUID. For consistent results, view as a table and not as individual entries. | ||||
| CmmHardwareVpdManufDate | 1.3.6.1.4.1.2.3.51.2.2.21.2.1.1.7 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Management module hardware VPD manufacture date. For consistent results, view as a table and not as individual entries. | ||||
| CmmHardwareVpdPartNumber | 1.3.6.1.4.1.2.3.51.2.2.21.2.1.1.8 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Management module hardware VPD Part number. For consistent results, view as a table and not as individual entries. | ||||
| CmmHardwareVpdFruSerial | 1.3.6.1.4.1.2.3.51.2.2.21.2.1.1.9 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Management module hardware VPD FRU serial number. For consistent results, view as a table and not as individual entries. | ||||
| CmmHardwareVpdManufacturingIDNumber | 1.3.6.1.4.1.2.3.51.2.2.21.2.1.1.10 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Management module hardware VPD manufacturer ID Number. For consistent results, view as a table and not as individual entries. | ||||
| CmmHardwareVpdProductId | 1.3.6.1.4.1.2.3.51.2.2.21.2.1.1.11 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Management module hardware VPD product ID. For consistent results, view as a table and not as individual entries. | ||||
| CmmHardwareVpdSubManufacturerId | 1.3.6.1.4.1.2.3.51.2.2.21.2.1.1.12 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Management module hardware VPD subsystem manufacturer. For consistent results, view as a table and not as individual entries. | ||||
| CmmHardwareVpdClei | 1.3.6.1.4.1.2.3.51.2.2.21.2.1.1.13 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Management module hardware VPD Common Language Equipment Identification (CLEI). For consistent results, view as a table and not as individual entries. | ||||
| CmmHardwareVpdHardwareRevisionString | 1.3.6.1.4.1.2.3.51.2.2.21.2.1.1.14 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Management module hardware VPD hardware revision in string format. For consistent results, view as a table and not as individual entries. If a hardware revision is programmed in the OEM VPD area for this component, then this MIB object should be used. | ||||
| NmmFirmwareVpd | 1.3.6.1.4.1.2.3.51.2.2.21.3 | |||
| TmmMainApplVpdTable | 1.3.6.1.4.1.2.3.51.2.2.21.3.1 | NA | deprecated | |
table · not-accessible · deprecated Table of MM Firmware VPD. | ||||
| RmmMainApplVpdEntry | 1.3.6.1.4.1.2.3.51.2.2.21.3.1.1 | NA | deprecated | |
| CmmMainApplVpdIndex | 1.3.6.1.4.1.2.3.51.2.2.21.3.1.1.1 | INTEGER | RO | deprecated |
column · INTEGER · read-only · deprecated Firmware VPD index. | ||||
| CmmMainApplVpdName | 1.3.6.1.4.1.2.3.51.2.2.21.3.1.1.2 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Firmware VPD name description. 'MM firmware' indicates the running firmware of the MM. 'MM firmware (pending restart)' indicates the flashed firmware of the MM which will become active after the next restart. | ||||
| CmmMainApplVpdBuildId | 1.3.6.1.4.1.2.3.51.2.2.21.3.1.1.3 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Firmware VPD build identification. | ||||
| CmmMainApplVpdRevisonNumber | 1.3.6.1.4.1.2.3.51.2.2.21.3.1.1.4 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Firmware VPD revision number. | ||||
| CmmMainApplVpdFilename | 1.3.6.1.4.1.2.3.51.2.2.21.3.1.1.5 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Firmware VPD file name. | ||||
| CmmMainApplVpdBuildDate | 1.3.6.1.4.1.2.3.51.2.2.21.3.1.1.6 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Firmware VPD build date. | ||||
| NbladeHardwareVpd | 1.3.6.1.4.1.2.3.51.2.2.21.4 | |||
| TbladeHardwareVpdTable | 1.3.6.1.4.1.2.3.51.2.2.21.4.1 | NA | deprecated | |
table · not-accessible · deprecated Table of VPD information for the blade hardware components. For consistent results, view as a table and not as individual entries. | ||||
| RbladeHardwareVpdEntry | 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1 | NA | deprecated | |
row · not-accessible · deprecated Blade hardware VPD entry. For consistent results, view as a table and not as individual entries. | ||||
| CbladeHardwareVpdIndex | 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1.1 | INTEGER | RO | deprecated |
column · INTEGER · read-only · deprecated Blade hardware VPD index. For consistent results, view as a table and not as individual entries. | ||||
| CbladeHardwareVpdBayNumber | 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1.2 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade hardware VPD Bay number. For consistent results, view as a table and not as individual entries. | ||||
| CbladeHardwareVpdManufacturingId | 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1.3 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade hardware VPD manufacturing ID. For consistent results, view as a table and not as individual entries. | ||||
| CbladeHardwareVpdFruNumber | 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1.4 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade hardware VPD FRU number. For consistent results, view as a table and not as individual entries. | ||||
| CbladeHardwareVpdHardwareRevision | 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1.5 | INTEGER | RO | deprecated |
column · INTEGER · read-only · deprecated Blade hardware VPD hardware revision. For consistent results, view as a table and not as individual entries. If a hardware revision is programmed in the OEM VPD area for this component, then the HardwareRevisionString version of this MIB object should be used. | ||||
| CbladeHardwareVpdSerialNumber | 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1.6 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade hardware VPD serial number. For consistent results, view as a table and not as individual entries. | ||||
| CbladeHardwareVpdMachineType | 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1.7 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade hardware VPD machine type. For consistent results, view as a table and not as individual entries. | ||||
| CbladeHardwareVpdUuid | 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1.8 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade hardware VPD UUID. For consistent results, view as a table and not as individual entries. | ||||
| CbladeHardwareVpdManufDate | 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1.9 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade hardware VPD Manufacture Date. For consistent results, view as a table and not as individual entries. | ||||
| CbladeHardwareVpdPartNumber | 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1.10 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade hardware VPD Part number. For consistent results, view as a table and not as individual entries. | ||||
| CbladeHardwareVpdFruSerial | 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1.11 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade hardware VPD FRU serial number. For consistent results, view as a table and not as individual entries. | ||||
| CbladeHardwareVpdMachineModel | 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1.12 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade hardware VPD machine model. For consistent results, view as a table and not as individual entries. | ||||
| CbladeHardwareVpdManufacturingIDNumber | 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1.13 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade hardware VPD Manufacturer ID Number. For consistent results, view as a table and not as individual entries. | ||||
| CbladeHardwareVpdProductId | 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1.14 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade hardware VPD product ID. For consistent results, view as a table and not as individual entries. | ||||
| CbladeHardwareVpdSubManufacturerId | 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1.15 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade hardware VPD subsystem manufacturer ID. For consistent results, view as a table and not as individual entries. | ||||
| CbladeHardwareVpdClei | 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1.16 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade hardware VPD Common Language Equipment Identifier (CLEI). For consistent results, view as a table and not as individual entries. | ||||
| CbladeHardwareVpdHardwareRevisionString | 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1.17 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade hardware VPD hardware revision in string format. For consistent results, view as a table and not as individual entries. If a hardware revision is programmed in the OEM VPD area for this component, then this MIB object should be used. | ||||
| CbladeDaughterVpdCardType | 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1.20 | INTEGER | RO | deprecated |
column · INTEGER · read-only · deprecated Blade expansion card (daughter card) VPD type. For consistent results, view as a table and not as individual entries.
| ||||
| CbladeDaughterVpdManufacturingId | 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1.21 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade expansion card (daughter card) VPD manufacturing ID. For consistent results, view as a table and not as individual entries. | ||||
| CbladeDaughterVpdFruNumber | 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1.22 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade expansion card (daughter card) VPD FRU number. For consistent results, view as a table and not as individual entries. | ||||
| CbladeDaughterVpdHardwareRevision | 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1.23 | INTEGER | RO | deprecated |
column · INTEGER · read-only · deprecated Blade expansion card (daughter card) VPD hardware revision. For consistent results, view as a table and not as individual entries. If a hardware revision is programmed in the OEM VPD area for this component, then the HardwareRevisionString version of this MIB object should be used. | ||||
| CbladeDaughterVpdSerialNumber | 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1.24 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade expansion card (daughter card) VPD Serial number. For consistent results, view as a table and not as individual entries. | ||||
| CbladeDaughterVpdMachineType | 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1.25 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade expansion card (daughter card) VPD Machine type. For consistent results, view as a table and not as individual entries. | ||||
| CbladeDaughterVpdUuid | 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1.26 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade expansion card (daughter card) VPD UUID. For consistent results, view as a table and not as individual entries. | ||||
| CbladeDaughterVpdManufDate | 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1.27 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade expansion card (daughter card) VPD Manufacture date. For consistent results, view as a table and not as individual entries. | ||||
| CbladeDaughterVpdPartNumber | 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1.28 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade expansion card (daughter card) VPD Part number. For consistent results, view as a table and not as individual entries. | ||||
| CbladeDaughterVpdFruSerial | 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1.29 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade expansion card (daughter card) VPD FRU Serial. For consistent results, view as a table and not as individual entries. | ||||
| CbladeDaughterVpdManufacturingIDNumber | 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1.30 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade expansion card (daughter card) VPD manufacturer ID Number. For consistent results, view as a table and not as individual entries. | ||||
| CbladeDaughterVpdProductId | 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1.31 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade expansion card (daughter card) VPD product ID. For consistent results, view as a table and not as individual entries. | ||||
| CbladeDaughterVpdSubManufacturerId | 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1.32 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade expansion card (daughter card) VPD subsystem manufacturing ID. For consistent results, view as a table and not as individual entries. | ||||
| CbladeDaughterVpdClei | 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1.33 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade expansion card (daughter card) VPD Common Language Equipment Identifier (CLEI). For consistent results, view as a table and not as individual entries. | ||||
| CbladeDaughterVpdHardwareRevisionString | 1.3.6.1.4.1.2.3.51.2.2.21.4.1.1.34 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade expansion card (daughter card) VPD hardware revision in string format. For consistent results, view as a table and not as individual entries. If a hardware revision is programmed in the OEM VPD area for this component, then this MIB object should be used. | ||||
| TbladeMACAddressVpdTable | 1.3.6.1.4.1.2.3.51.2.2.21.4.2 | NA | mandatory | |
table · not-accessible · mandatory Table of MAC addresses of the blade and its expansion cards (daughter cards). For consistent results, view as a table and not as individual entries. | ||||
| RbladeMACAddressVpdEntry | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1 | NA | mandatory | |
row · not-accessible · mandatory Blade MAC address entry. For consistent results, view as a table and not as individual entries. | ||||
| CbladeMACAddressVpdIndex | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Blade index. For consistent results, view as a table and not as individual entries. | ||||
| CbladeMACAddress1Vpd | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.2 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade MAC address 1. For consistent results, view as a table and not as individual entries. | ||||
| CbladeMACAddress2Vpd | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.3 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade MAC address 2. For consistent results, view as a table and not as individual entries. | ||||
| CbladeMACAddress3Vpd | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.4 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade MAC address 3. For consistent results, view as a table and not as individual entries. | ||||
| CbladeMACAddress4Vpd | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.5 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade MAC address 4. For consistent results, view as a table and not as individual entries. | ||||
| CbladeMACAddress5Vpd | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.6 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade MAC address 5. For consistent results, view as a table and not as individual entries. | ||||
| CbladeMACAddress6Vpd | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.7 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade MAC address 6. For consistent results, view as a table and not as individual entries. | ||||
| CbladeMACAddress7Vpd | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.8 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade MAC address 7. For consistent results, view as a table and not as individual entries. | ||||
| CbladeMACAddress8Vpd | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.9 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade MAC address 8. For consistent results, view as a table and not as individual entries. | ||||
| CbladeDaughterCard1MACAddress1Vpd | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.10 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade expansion card (daughter card) 1 MAC address 1. For consistent results, view as a table and not as individual entries. | ||||
| CbladeDaughterCard1MACAddress2Vpd | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.11 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade expansion card (daughter card) 1 MAC address 2. For consistent results, view as a table and not as individual entries. | ||||
| CbladeDaughterCard1MACAddress3Vpd | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.12 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade expansion card (daughter card) 1 MAC address 3. For consistent results, view as a table and not as individual entries. | ||||
| CbladeDaughterCard1MACAddress4Vpd | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.13 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade expansion card (daughter card) 1 MAC address 4. For consistent results, view as a table and not as individual entries. | ||||
| CbladeDaughterCard1MACAddress5Vpd | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.14 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade expansion card (daughter card) 1 MAC address 5. For consistent results, view as a table and not as individual entries. | ||||
| CbladeDaughterCard1MACAddress6Vpd | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.15 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade expansion card (daughter card) 1 MAC address 6. For consistent results, view as a table and not as individual entries. | ||||
| CbladeDaughterCard1MACAddress7Vpd | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.16 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade expansion card (daughter card) 1 MAC address 7. For consistent results, view as a table and not as individual entries. | ||||
| CbladeDaughterCard1MACAddress8Vpd | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.17 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade expansion card (daughter card) 1 MAC address 8. For consistent results, view as a table and not as individual entries. | ||||
| CbladeDaughterCard2MACAddress1Vpd | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.18 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade expansion card (daughter card) 2 MAC address 1. For consistent results, view as a table and not as individual entries. | ||||
| CbladeDaughterCard2MACAddress2Vpd | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.19 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade expansion card (daughter card) 2 MAC address 2. For consistent results, view as a table and not as individual entries. | ||||
| CbladeDaughterCard2MACAddress3Vpd | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.20 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade expansion card (daughter card) 2 MAC address 3. For consistent results, view as a table and not as individual entries. | ||||
| CbladeDaughterCard2MACAddress4Vpd | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.21 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade expansion card (daughter card) 2 MAC address 4. For consistent results, view as a table and not as individual entries. | ||||
| CbladeDaughterCard2MACAddress5Vpd | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.22 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade expansion card (daughter card) 2 MAC address 5. For consistent results, view as a table and not as individual entries. | ||||
| CbladeDaughterCard2MACAddress6Vpd | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.23 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade expansion card (daughter card) 2 MAC address 6. For consistent results, view as a table and not as individual entries. | ||||
| CbladeDaughterCard2MACAddress7Vpd | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.24 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade expansion card (daughter card) 2 MAC address 7. For consistent results, view as a table and not as individual entries. | ||||
| CbladeDaughterCard2MACAddress8Vpd | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.25 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade expansion card (daughter card) 2 MAC address 8. For consistent results, view as a table and not as individual entries. | ||||
| CbladeDaughterCard3MACAddress1Vpd | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.26 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade expansion card (daughter card) 3 MAC address 1. For consistent results, view as a table and not as individual entries. | ||||
| CbladeDaughterCard3MACAddress2Vpd | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.27 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade expansion card (daughter card) 3 MAC address 2. For consistent results, view as a table and not as individual entries. | ||||
| CbladeDaughterCard3MACAddress3Vpd | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.28 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade expansion card (daughter card) 3 MAC address 3. For consistent results, view as a table and not as individual entries. | ||||
| CbladeDaughterCard3MACAddress4Vpd | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.29 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade expansion card (daughter card) 3 MAC address 4. For consistent results, view as a table and not as individual entries. | ||||
| CbladeDaughterCard3MACAddress5Vpd | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.30 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade expansion card (daughter card) 3 MAC address 5. For consistent results, view as a table and not as individual entries. | ||||
| CbladeDaughterCard3MACAddress6Vpd | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.31 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade expansion card (daughter card) 3 MAC address 6. For consistent results, view as a table and not as individual entries. | ||||
| CbladeDaughterCard3MACAddress7Vpd | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.32 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade expansion card (daughter card) 3 MAC address 7. For consistent results, view as a table and not as individual entries. | ||||
| CbladeDaughterCard3MACAddress8Vpd | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.33 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade expansion card (daughter card) 3 MAC address 8. For consistent results, view as a table and not as individual entries. | ||||
| CbladeDaughterCard4MACAddress1Vpd | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.34 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade expansion card (daughter card) 4 MAC address 1. For consistent results, view as a table and not as individual entries. | ||||
| CbladeDaughterCard4MACAddress2Vpd | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.35 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade expansion card (daughter card) 4 MAC address 2. For consistent results, view as a table and not as individual entries. | ||||
| CbladeDaughterCard4MACAddress3Vpd | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.36 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade expansion card (daughter card) 4 MAC address 3. For consistent results, view as a table and not as individual entries. | ||||
| CbladeDaughterCard4MACAddress4Vpd | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.37 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade expansion card (daughter card) 4 MAC address 4. For consistent results, view as a table and not as individual entries. | ||||
| CbladeDaughterCard4MACAddress5Vpd | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.38 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade expansion card (daughter card) 4 MAC address 5. For consistent results, view as a table and not as individual entries. | ||||
| CbladeDaughterCard4MACAddress6Vpd | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.39 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade expansion card (daughter card) 4 MAC address 6. For consistent results, view as a table and not as individual entries. | ||||
| CbladeDaughterCard4MACAddress7Vpd | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.40 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade expansion card (daughter card) 4 MAC address 7. For consistent results, view as a table and not as individual entries. | ||||
| CbladeDaughterCard4MACAddress8Vpd | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.41 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade expansion card (daughter card) 4 MAC address 8. For consistent results, view as a table and not as individual entries. | ||||
| CbladeDaughterCard5MACAddress1Vpd | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.42 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade expansion card (daughter card) 5 MAC address 1. For consistent results, view as a table and not as individual entries. | ||||
| CbladeDaughterCard5MACAddress2Vpd | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.43 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade expansion card (daughter card) 5 MAC address 2. For consistent results, view as a table and not as individual entries. | ||||
| CbladeDaughterCard5MACAddress3Vpd | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.44 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade expansion card (daughter card) 5 MAC address 3. For consistent results, view as a table and not as individual entries. | ||||
| CbladeDaughterCard5MACAddress4Vpd | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.45 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade expansion card (daughter card) 5 MAC address 4. For consistent results, view as a table and not as individual entries. | ||||
| CbladeDaughterCard5MACAddress5Vpd | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.46 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade expansion card (daughter card) 5 MAC address 5. For consistent results, view as a table and not as individual entries. | ||||
| CbladeDaughterCard5MACAddress6Vpd | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.47 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade expansion card (daughter card) 5 MAC address 6. For consistent results, view as a table and not as individual entries. | ||||
| CbladeDaughterCard5MACAddress7Vpd | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.48 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade expansion card (daughter card) 5 MAC address 7. For consistent results, view as a table and not as individual entries. | ||||
| CbladeDaughterCard5MACAddress8Vpd | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.49 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade expansion card (daughter card) 5 MAC address 8. For consistent results, view as a table and not as individual entries. | ||||
| CbladeHSDaughterCard1MACAddress1Vpd | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.100 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade high speed expansion card (daughter card) 1 MAC address 1. For consistent results, view as a table and not as individual entries. | ||||
| CbladeHSDaughterCard1MACAddress2Vpd | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.101 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade high speed expansion card (daughter card) 1 MAC address 2. For consistent results, view as a table and not as individual entries. | ||||
| CbladeHSDaughterCard1MACAddress3Vpd | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.102 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade high speed expansion card (daughter card) 1 MAC address 3. For consistent results, view as a table and not as individual entries. | ||||
| CbladeHSDaughterCard1MACAddress4Vpd | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.103 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade high speed expansion card (daughter card) 1 MAC address 4. For consistent results, view as a table and not as individual entries. | ||||
| CbladeHSDaughterCard1MACAddress5Vpd | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.104 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade high speed expansion card (daughter card) 1 MAC address 5. For consistent results, view as a table and not as individual entries. | ||||
| CbladeHSDaughterCard1MACAddress6Vpd | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.105 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade high speed expansion card (daughter card) 1 MAC address 6. For consistent results, view as a table and not as individual entries. | ||||
| CbladeHSDaughterCard1MACAddress7Vpd | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.106 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade high speed expansion card (daughter card) 1 MAC address 7. For consistent results, view as a table and not as individual entries. | ||||
| CbladeHSDaughterCard1MACAddress8Vpd | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.107 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade high speed expansion card (daughter card) 1 MAC address 8. For consistent results, view as a table and not as individual entries. | ||||
| CbladeSideCardMACAddress1Vpd | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.164 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade side card MAC address 1. For consistent results, view as a table and not as individual entries. | ||||
| CbladeSideCardMACAddress2Vpd | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.165 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade side card MAC address 2. For consistent results, view as a table and not as individual entries. | ||||
| CbladeSideCardMACAddress3Vpd | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.166 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade side card MAC address 3. For consistent results, view as a table and not as individual entries. | ||||
| CbladeSideCardMACAddress4Vpd | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.167 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade side card MAC address 4. For consistent results, view as a table and not as individual entries. | ||||
| CbladeSideCardMACAddress5Vpd | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.168 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade side card MAC address 5. For consistent results, view as a table and not as individual entries. | ||||
| CbladeSideCardMACAddress6Vpd | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.169 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade side card MAC address 6. For consistent results, view as a table and not as individual entries. | ||||
| CbladeSideCardMACAddress7Vpd | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.170 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade side card MAC address 7. For consistent results, view as a table and not as individual entries. | ||||
| CbladeSideCardMACAddress8Vpd | 1.3.6.1.4.1.2.3.51.2.2.21.4.2.1.171 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Blade side card MAC address 8. For consistent results, view as a table and not as individual entries. | ||||
| TbladeExpCardVpdTable | 1.3.6.1.4.1.2.3.51.2.2.21.4.5 | NA | deprecated | |
table · not-accessible · deprecated Table of VPD information for the blade expansion card components. For consistent results, view as a table and not as individual entries. | ||||
| RbladeExpCardVpdEntry | 1.3.6.1.4.1.2.3.51.2.2.21.4.5.1 | NA | deprecated | |
row · not-accessible · deprecated Blade expansion card VPD entry. For consistent results, view as a table and not as individual entries.
| ||||
| CbladeExpCardVpdIndex | 1.3.6.1.4.1.2.3.51.2.2.21.4.5.1.1 | INTEGER | RO | deprecated |
column · INTEGER · read-only · deprecated Blade expansion card VPD index. For consistent results, view as a table and not as individual entries. | ||||
| CbladeExpCardVpdBayNumber | 1.3.6.1.4.1.2.3.51.2.2.21.4.5.1.2 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade expansion card VPD Bay number. For consistent results, view as a table and not as individual entries. | ||||
| CbladeExpCardVpdManufacturingId | 1.3.6.1.4.1.2.3.51.2.2.21.4.5.1.3 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade expansion card VPD manufacturing ID. For consistent results, view as a table and not as individual entries. | ||||
| CbladeExpCardVpdFruNumber | 1.3.6.1.4.1.2.3.51.2.2.21.4.5.1.4 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade expansion card VPD FRU number. For consistent results, view as a table and not as individual entries. | ||||
| CbladeExpCardVpdHardwareRevision | 1.3.6.1.4.1.2.3.51.2.2.21.4.5.1.5 | INTEGER | RO | deprecated |
column · INTEGER · read-only · deprecated Blade expansion card VPD hardware revision. For consistent results, view as a table and not as individual entries. If a hardware revision is programmed in the OEM VPD area for this component, then the HardwareRevisionString version of this MIB object should be used. | ||||
| CbladeExpCardVpdSerialNumber | 1.3.6.1.4.1.2.3.51.2.2.21.4.5.1.6 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade expansion card VPD serial number. For consistent results, view as a table and not as individual entries. | ||||
| CbladeExpCardVpdMachineType | 1.3.6.1.4.1.2.3.51.2.2.21.4.5.1.7 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade expansion card VPD machine type. For consistent results, view as a table and not as individual entries. | ||||
| CbladeExpCardVpdUuid | 1.3.6.1.4.1.2.3.51.2.2.21.4.5.1.8 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade expansion card VPD UUID. For consistent results, view as a table and not as individual entries. | ||||
| CbladeExpCardVpdManufDate | 1.3.6.1.4.1.2.3.51.2.2.21.4.5.1.9 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade expansion card VPD Manufacture Date. For consistent results, view as a table and not as individual entries. | ||||
| CbladeExpCardVpdPartNumber | 1.3.6.1.4.1.2.3.51.2.2.21.4.5.1.10 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade expansion card VPD Part number. For consistent results, view as a table and not as individual entries. | ||||
| CbladeExpCardVpdFruSerial | 1.3.6.1.4.1.2.3.51.2.2.21.4.5.1.11 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade expansion card VPD FRU serial number. For consistent results, view as a table and not as individual entries. | ||||
| CbladeExpCardVpdMachineModel | 1.3.6.1.4.1.2.3.51.2.2.21.4.5.1.12 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade expansion card VPD machine model. For consistent results, view as a table and not as individual entries. | ||||
| CbladeExpCardVpdManufacturingIDNumber | 1.3.6.1.4.1.2.3.51.2.2.21.4.5.1.13 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade expansion card VPD Manufacturer ID Number. For consistent results, view as a table and not as individual entries. | ||||
| CbladeExpCardVpdProductId | 1.3.6.1.4.1.2.3.51.2.2.21.4.5.1.14 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade expansion card VPD Product ID. For consistent results, view as a table and not as individual entries. | ||||
| CbladeExpCardVpdSubManufacturerId | 1.3.6.1.4.1.2.3.51.2.2.21.4.5.1.15 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade expansion card VPD subsystem manufacturer ID. For consistent results, view as a table and not as individual entries. | ||||
| CbladeExpCardVpdClei | 1.3.6.1.4.1.2.3.51.2.2.21.4.5.1.16 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade expansion card VPD Common Language Equipment Identifier (CLEI). For consistent results, view as a table and not as individual entries. | ||||
| CbladeExpCardVpdBladeBayNumber | 1.3.6.1.4.1.2.3.51.2.2.21.4.5.1.19 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade bay number of the blade expansion card. For consistent results, view as a table and not as individual entries. | ||||
| CbladeExpCardVpdCardTypeInfo | 1.3.6.1.4.1.2.3.51.2.2.21.4.5.1.21 | INTEGER | RO | deprecated |
column · INTEGER · read-only · deprecated Blade expansion card (daughter card) VPD type code that describes the expansion card. For consistent results, view as a table and not as individual entries. NOTE: The CFFe expansion card is also referred to as a CFFh expansion card.
| ||||
| CbladeExpCardVpdHighSpeed | 1.3.6.1.4.1.2.3.51.2.2.21.4.5.1.22 | INTEGER | RO | deprecated |
column · INTEGER · read-only · deprecated Blade expansion card (daughter card) VPD high speed that indicates whether the expansion card is high speed or not. For consistent results, view as a table and not as individual entries.
| ||||
| CbladeExpCardVpdHardwareRevisionString | 1.3.6.1.4.1.2.3.51.2.2.21.4.5.1.23 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade expansion card VPD hardware revision in string format. For consistent results, view as a table and not as individual entries. If a hardware revision is programmed in the OEM VPD area for this component, then this MIB object should be used. | ||||
| TbladeAndExpCardWwnGuidVpdTable | 1.3.6.1.4.1.2.3.51.2.2.21.4.7 | NA | deprecated | |
table · not-accessible · deprecated Table of World Wide Names (WWN), Global Unique IDs (GUID) and Serial Attach SCSI IDs (SAS) of the blade server and its expansion cards (daughter cards). For consistent results, view as a table and not as individual entries. | ||||
| RbladeAndExpCardWwnGuidVpdEntry | 1.3.6.1.4.1.2.3.51.2.2.21.4.7.1 | NA | deprecated | |
row · not-accessible · deprecated Blade WWN/GUID entries. For consistent results, view as a table and not as individual entries. | ||||
| CbladeAndExpCardWwnGuidVpdIndex | 1.3.6.1.4.1.2.3.51.2.2.21.4.7.1.1 | INTEGER | RO | deprecated |
column · INTEGER · read-only · deprecated Blade or expansion card index. For consistent results, view as a table and not as individual entries. | ||||
| CbladeAndExpCardWwnGuidVpdBayNumber | 1.3.6.1.4.1.2.3.51.2.2.21.4.7.1.2 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade or expansion card VPD bay number. For consistent results, view as a table and not as individual entries. | ||||
| CbladeAndExpCardWwnGuidVpdName | 1.3.6.1.4.1.2.3.51.2.2.21.4.7.1.3 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated The name of the blade or expansion card. For consistent results, view as a table and not as individual entries. | ||||
| CbladeAndExpCardWwnGuidVpdBladeBayNumber | 1.3.6.1.4.1.2.3.51.2.2.21.4.7.1.4 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated For expansion cards, it's the blade bay number of the blade expansion card. For blades, it's the bay number of the blade. For consistent results, view as a table and not as individual entries. | ||||
| CbladeAndExpCardWwnGuidVpdType | 1.3.6.1.4.1.2.3.51.2.2.21.4.7.1.5 | INTEGER | RO | deprecated |
column · INTEGER · read-only · deprecated Blade or expansion card WWN/GUID/SAS Type. For consistent results, view as a table and not as individual entries.
| ||||
| CbladeAndExpCardWwnGuidVpd1 | 1.3.6.1.4.1.2.3.51.2.2.21.4.7.1.6 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade or expansion card WWN/GUID 1. For consistent results, view as a table and not as individual entries. | ||||
| CbladeAndExpCardWwnGuidVpd2 | 1.3.6.1.4.1.2.3.51.2.2.21.4.7.1.7 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade or expansion card WWN/GUID 2. For consistent results, view as a table and not as individual entries. | ||||
| CbladeAndExpCardWwnGuidVpd3 | 1.3.6.1.4.1.2.3.51.2.2.21.4.7.1.8 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade or expansion card WWN/GUID 3. For consistent results, view as a table and not as individual entries. | ||||
| CbladeAndExpCardWwnGuidVpd4 | 1.3.6.1.4.1.2.3.51.2.2.21.4.7.1.9 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade or expansion card WWN/GUID 4. For consistent results, view as a table and not as individual entries. | ||||
| CbladeAndExpCardWwnGuidVpd5 | 1.3.6.1.4.1.2.3.51.2.2.21.4.7.1.10 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade or expansion card WWN/GUID 5. For consistent results, view as a table and not as individual entries. | ||||
| CbladeAndExpCardWwnGuidVpd6 | 1.3.6.1.4.1.2.3.51.2.2.21.4.7.1.11 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade or expansion card WWN/GUID 6. For consistent results, view as a table and not as individual entries. | ||||
| CbladeAndExpCardWwnGuidVpd7 | 1.3.6.1.4.1.2.3.51.2.2.21.4.7.1.12 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade or expansion card WWN/GUID 7. For consistent results, view as a table and not as individual entries. | ||||
| CbladeAndExpCardWwnGuidVpd8 | 1.3.6.1.4.1.2.3.51.2.2.21.4.7.1.13 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade or expansion card WWN/GUID 8. For consistent results, view as a table and not as individual entries. | ||||
| TbladeManagementCardVpdTable | 1.3.6.1.4.1.2.3.51.2.2.21.4.8 | NA | deprecated | |
table · not-accessible · deprecated Table of VPD information for the blade management card component. For consistent results, view as a table and not as individual entries. | ||||
| RbladeManagementCardVpdEntry | 1.3.6.1.4.1.2.3.51.2.2.21.4.8.1 | NA | deprecated | |
row · not-accessible · deprecated Blade management card VPD entry. For consistent results, view as a table and not as individual entries. | ||||
| CbladeManagementCardVpdIndex | 1.3.6.1.4.1.2.3.51.2.2.21.4.8.1.1 | INTEGER | RO | deprecated |
column · INTEGER · read-only · deprecated Blade management card VPD index. For consistent results, view as a table and not as individual entries. | ||||
| CbladeManagementCardVpdBayNumber | 1.3.6.1.4.1.2.3.51.2.2.21.4.8.1.2 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade management card VPD Bay number. For consistent results, view as a table and not as individual entries. | ||||
| CbladeManagementCardVpdManufacturingId | 1.3.6.1.4.1.2.3.51.2.2.21.4.8.1.3 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade management card VPD manufacturing ID. For consistent results, view as a table and not as individual entries. | ||||
| CbladeManagementCardVpdFruNumber | 1.3.6.1.4.1.2.3.51.2.2.21.4.8.1.4 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade management card VPD FRU number. For consistent results, view as a table and not as individual entries. | ||||
| CbladeManagementCardVpdHardwareRevision | 1.3.6.1.4.1.2.3.51.2.2.21.4.8.1.5 | INTEGER | RO | deprecated |
column · INTEGER · read-only · deprecated Blade management card VPD hardware revision. For consistent results, view as a table and not as individual entries. If a hardware revision is programmed in the OEM VPD area for this component, then the HardwareRevisionString version of this MIB object should be used. | ||||
| CbladeManagementCardVpdSerialNumber | 1.3.6.1.4.1.2.3.51.2.2.21.4.8.1.6 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade management card VPD serial number. For consistent results, view as a table and not as individual entries. | ||||
| CbladeManagementCardVpdMachineType | 1.3.6.1.4.1.2.3.51.2.2.21.4.8.1.7 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade management card VPD machine type. For consistent results, view as a table and not as individual entries. | ||||
| CbladeManagementCardVpdUuid | 1.3.6.1.4.1.2.3.51.2.2.21.4.8.1.8 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade management card VPD UUID. For consistent results, view as a table and not as individual entries. | ||||
| CbladeManagementCardVpdManufDate | 1.3.6.1.4.1.2.3.51.2.2.21.4.8.1.9 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade management card VPD Manufacture Date. For consistent results, view as a table and not as individual entries. | ||||
| CbladeManagementCardVpdPartNumber | 1.3.6.1.4.1.2.3.51.2.2.21.4.8.1.10 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade management card VPD Part number. For consistent results, view as a table and not as individual entries. | ||||
| CbladeManagementCardVpdFruSerial | 1.3.6.1.4.1.2.3.51.2.2.21.4.8.1.11 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade management card VPD FRU serial number. For consistent results, view as a table and not as individual entries. | ||||
| CbladeManagementCardVpdMachineModel | 1.3.6.1.4.1.2.3.51.2.2.21.4.8.1.12 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade management card VPD machine model. For consistent results, view as a table and not as individual entries. | ||||
| CbladeManagementCardVpdManufacturingIDNumber | 1.3.6.1.4.1.2.3.51.2.2.21.4.8.1.13 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade management card VPD manufacturer ID. For consistent results, view as a table and not as individual entries. | ||||
| CbladeManagementCardVpdProductId | 1.3.6.1.4.1.2.3.51.2.2.21.4.8.1.14 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade management card VPD Product ID. For consistent results, view as a table and not as individual entries. | ||||
| CbladeManagementCardVpdSubManufacturerId | 1.3.6.1.4.1.2.3.51.2.2.21.4.8.1.15 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade management card VPD subsystem manufacturer ID. For consistent results, view as a table and not as individual entries. | ||||
| CbladeManagementCardVpdClei | 1.3.6.1.4.1.2.3.51.2.2.21.4.8.1.16 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade management card VPD Common Language Equipment Identifier (CLEI). For consistent results, view as a table and not as individual entries. | ||||
| CbladeManagementCardVpdHardwareRevisionString | 1.3.6.1.4.1.2.3.51.2.2.21.4.8.1.17 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Blade management card VPD hardware revision in string format. For consistent results, view as a table and not as individual entries. If a hardware revision is programmed in the OEM VPD area for this component, then this MIB object should be used. | ||||
| NbladeFirmwareVpd | 1.3.6.1.4.1.2.3.51.2.2.21.5 | |||
| TbladeBiosVPDTable | 1.3.6.1.4.1.2.3.51.2.2.21.5.1 | NA | deprecated | |
table · not-accessible · deprecated Table of blade firmware vital product data (VPD) information. | ||||
| RbladeBiosVPDEntry | 1.3.6.1.4.1.2.3.51.2.2.21.5.1.1 | NA | deprecated | |
| CbladeBiosVpdIndex | 1.3.6.1.4.1.2.3.51.2.2.21.5.1.1.1 | INTEGER | RO | deprecated |
column · INTEGER · read-only · deprecated Blade firmware VPD table index. | ||||
| CbladeBiosVpdId | 1.3.6.1.4.1.2.3.51.2.2.21.5.1.1.2 | INTEGER | RO | deprecated |
column · INTEGER · read-only · deprecated The numeric blade ID.
| ||||
| CbladeBiosVpdExists | 1.3.6.1.4.1.2.3.51.2.2.21.5.1.1.3 | INTEGER | RO | deprecated |
column · INTEGER · read-only · deprecated Indicates whether the server blade specified exists or not.
| ||||
| CbladeBiosVpdPowerState | 1.3.6.1.4.1.2.3.51.2.2.21.5.1.1.4 | INTEGER | RO | deprecated |
column · INTEGER · read-only · deprecated Indicates the power state of the blade specified.
| ||||
| CbladeBiosVpdName | 1.3.6.1.4.1.2.3.51.2.2.21.5.1.1.5 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated The name of the blade as a null terminated string. | ||||
| CbladeBiosVpdBuildId | 1.3.6.1.4.1.2.3.51.2.2.21.5.1.1.6 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated The build ID for the blade firmware. | ||||
| CbladeBiosVpdRevision | 1.3.6.1.4.1.2.3.51.2.2.21.5.1.1.7 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated The revision of the blade firmware. | ||||
| CbladeBiosVpdDate | 1.3.6.1.4.1.2.3.51.2.2.21.5.1.1.8 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated The date of the blade firmware. | ||||
| CbladeBiosVpdLevelStatus | 1.3.6.1.4.1.2.3.51.2.2.21.5.1.1.9 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated The level status of the blade bios firmware build ID. It has three possible values as Different (mismatch firmware build ID), Match (the same firmware build ID), Unique (only one such firmware build ID). | ||||
| TbladeDiagsVPDTable | 1.3.6.1.4.1.2.3.51.2.2.21.5.2 | NA | deprecated | |
table · not-accessible · deprecated Table of blade firmware vital product data (VPD) information. | ||||
| RbladeDiagsVPDEntry | 1.3.6.1.4.1.2.3.51.2.2.21.5.2.1 | NA | deprecated | |
| CbladeDiagsVpdIndex | 1.3.6.1.4.1.2.3.51.2.2.21.5.2.1.1 | INTEGER | RO | deprecated |
column · INTEGER · read-only · deprecated Blade firmware VPD table index. | ||||
| CbladeDiagsVpdId | 1.3.6.1.4.1.2.3.51.2.2.21.5.2.1.2 | INTEGER | RO | deprecated |
column · INTEGER · read-only · deprecated The numeric blade ID.
| ||||
| CbladeDiagsVpdExists | 1.3.6.1.4.1.2.3.51.2.2.21.5.2.1.3 | INTEGER | RO | deprecated |
column · INTEGER · read-only · deprecated Indicates whether the server blade specified exists or not.
| ||||
| CbladeDiagsVpdPowerState | 1.3.6.1.4.1.2.3.51.2.2.21.5.2.1.4 | INTEGER | RO | deprecated |
column · INTEGER · read-only · deprecated Indicates the power state of the blade specified.
| ||||
| CbladeDiagsVpdName | 1.3.6.1.4.1.2.3.51.2.2.21.5.2.1.5 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated The name of the blade as a null terminated string. | ||||
| CbladeDiagsVpdBuildId | 1.3.6.1.4.1.2.3.51.2.2.21.5.2.1.6 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated The build ID for the blade firmware. | ||||
| CbladeDiagsVpdRevision | 1.3.6.1.4.1.2.3.51.2.2.21.5.2.1.7 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated The revision of the blade firmware. | ||||
| CbladeDiagsVpdDate | 1.3.6.1.4.1.2.3.51.2.2.21.5.2.1.8 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated The date of the blade firmware. | ||||
| CbladeDiagsVpdLevelStatus | 1.3.6.1.4.1.2.3.51.2.2.21.5.2.1.9 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated The level status of the blade diagnostics firmware build ID. It has three possible values as Different (mismatch firmware build ID), Match (the same firmware build ID), Unique (only one such firmware build ID). | ||||
| TbladeSysMgmtProcVPDTable | 1.3.6.1.4.1.2.3.51.2.2.21.5.3 | NA | deprecated | |
table · not-accessible · deprecated Table of blade firmware vital product data (VPD) information. | ||||
| RbladeSysMgmtProcVPDEntry | 1.3.6.1.4.1.2.3.51.2.2.21.5.3.1 | NA | deprecated | |
| CbladeSysMgmtProcVpdIndex | 1.3.6.1.4.1.2.3.51.2.2.21.5.3.1.1 | INTEGER | RO | deprecated |
column · INTEGER · read-only · deprecated Blade firmware VPD table index. | ||||
| CbladeSysMgmtProcVpdId | 1.3.6.1.4.1.2.3.51.2.2.21.5.3.1.2 | INTEGER | RO | deprecated |
column · INTEGER · read-only · deprecated The numeric blade ID.
| ||||
| CbladeSysMgmtProcVpdExists | 1.3.6.1.4.1.2.3.51.2.2.21.5.3.1.3 | INTEGER | RO | deprecated |
column · INTEGER · read-only · deprecated Indicates whether the server blade specified exists or not.
| ||||
| CbladeSysMgmtProcVpdPowerState | 1.3.6.1.4.1.2.3.51.2.2.21.5.3.1.4 | INTEGER | RO | deprecated |
column · INTEGER · read-only · deprecated Indicates the power state of the blade specified.
| ||||
| CbladeSysMgmtProcVpdName | 1.3.6.1.4.1.2.3.51.2.2.21.5.3.1.5 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated The name of the blade as a null terminated string. | ||||
| CbladeSysMgmtProcVpdBuildId | 1.3.6.1.4.1.2.3.51.2.2.21.5.3.1.6 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated The build ID for the blade firmware. | ||||
| CbladeSysMgmtProcVpdRevision | 1.3.6.1.4.1.2.3.51.2.2.21.5.3.1.7 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated The revision of the blade firmware. | ||||
| CbladeSysMgmtProcVpdLevelStatus | 1.3.6.1.4.1.2.3.51.2.2.21.5.3.1.8 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated The level status of the blade system management processor firmware build ID. It has three possible values as Different (mismatch firmware build ID), Match (the same firmware build ID), Unique (only one such firmware build ID). | ||||
| NsmHardwareVpd | 1.3.6.1.4.1.2.3.51.2.2.21.6 | |||
| TsmHardwareVpdTable | 1.3.6.1.4.1.2.3.51.2.2.21.6.1 | NA | deprecated | |
table · not-accessible · deprecated Table of the switch module hardware components. For consistent results, view as a table and not as individual entries. | ||||
| RsmHardwareVpdEntry | 1.3.6.1.4.1.2.3.51.2.2.21.6.1.1 | NA | deprecated | |
row · not-accessible · deprecated Switch module hardware VPD entry. For consistent results, view as a table and not as individual entries.
| ||||
| CsmHardwareVpdIndex | 1.3.6.1.4.1.2.3.51.2.2.21.6.1.1.1 | INTEGER | RO | deprecated |
column · INTEGER · read-only · deprecated Switch module hardware VPD index. For consistent results, view as a table and not as individual entries. | ||||
| CsmHardwareVpdBayNumber | 1.3.6.1.4.1.2.3.51.2.2.21.6.1.1.2 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Switch module hardware VPD Bay number. For consistent results, view as a table and not as individual entries. | ||||
| CsmHardwareVpdManufacturingId | 1.3.6.1.4.1.2.3.51.2.2.21.6.1.1.3 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Switch module hardware VPD manufacturing ID. For consistent results, view as a table and not as individual entries. | ||||
| CsmHardwareVpdFruNumber | 1.3.6.1.4.1.2.3.51.2.2.21.6.1.1.4 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Switch module hardware VPD FRU number. For consistent results, view as a table and not as individual entries. | ||||
| CsmHardwareVpdHardwareRevision | 1.3.6.1.4.1.2.3.51.2.2.21.6.1.1.5 | INTEGER | RO | deprecated |
column · INTEGER · read-only · deprecated Switch module hardware VPD hardware revision. For consistent results, view as a table and not as individual entries. If a hardware revision is programmed in the OEM VPD area for this component, then the HardwareRevisionString version of this MIB object should be used. | ||||
| CsmHardwareVpdUuid | 1.3.6.1.4.1.2.3.51.2.2.21.6.1.1.8 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Switch module hardware VPD UUID. For consistent results, view as a table and not as individual entries. | ||||
| CsmHardwareVpdManufDate | 1.3.6.1.4.1.2.3.51.2.2.21.6.1.1.9 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Switch module hardware VPD manufacture date. For consistent results, view as a table and not as individual entries. | ||||
| CsmHardwareVpdPartNumber | 1.3.6.1.4.1.2.3.51.2.2.21.6.1.1.10 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Switch module hardware VPD Part Number. For consistent results, view as a table and not as individual entries. | ||||
| CsmHardwareVpdFruSerial | 1.3.6.1.4.1.2.3.51.2.2.21.6.1.1.11 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Switch module hardware VPD FRU Serial. For consistent results, view as a table and not as individual entries. | ||||
| CsmHardwareVpdManufacturingIDNumber | 1.3.6.1.4.1.2.3.51.2.2.21.6.1.1.12 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Switch module hardware VPD manufacturer ID. For consistent results, view as a table and not as individual entries. | ||||
| CsmHardwareVpdProductId | 1.3.6.1.4.1.2.3.51.2.2.21.6.1.1.13 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Switch module hardware VPD product ID. For consistent results, view as a table and not as individual entries. | ||||
| CsmHardwareVpdSubManufacturerId | 1.3.6.1.4.1.2.3.51.2.2.21.6.1.1.14 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Switch module hardware VPD subsystem manufacturer ID. For consistent results, view as a table and not as individual entries. | ||||
| CsmHardwareVpdClei | 1.3.6.1.4.1.2.3.51.2.2.21.6.1.1.15 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Switch module hardware VPD Common Language Equipment Identifier (CLEI). For consistent results, view as a table and not as individual entries. | ||||
| CsmHardwareVpdWwnGuid | 1.3.6.1.4.1.2.3.51.2.2.21.6.1.1.16 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Switch module hardware VPD World Wide Name or Global Unique ID. For consistent results, view as a table and not as individual entries. | ||||
| CsmHardwareVpdWwnGuidType | 1.3.6.1.4.1.2.3.51.2.2.21.6.1.1.17 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated The WWN/GUID/SAS entry is actually World Wide Name, Global Unique ID or Serial Attach SCSI ID. For consistent results, view as a table and not as individual entries. | ||||
| CsmHardwareVpdWidth | 1.3.6.1.4.1.2.3.51.2.2.21.6.1.1.18 | INTEGER | RO | deprecated |
column · INTEGER · read-only · deprecated The width of the switch module hardware. For consistent results, view as a table and not as individual entries. | ||||
| CsmHardwareVpdHardwareRevisionString | 1.3.6.1.4.1.2.3.51.2.2.21.6.1.1.20 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Switch module hardware VPD hardware revision in string format. For consistent results, view as a table and not as individual entries. If a hardware revision is programmed in the OEM VPD area for this component, then this MIB object should be used. | ||||
| NsmFirmwareVpd | 1.3.6.1.4.1.2.3.51.2.2.21.7 | |||
| TsmMainAppVpdTable | 1.3.6.1.4.1.2.3.51.2.2.21.7.1 | NA | deprecated | |
table · not-accessible · deprecated Switch module main application VPD information table. | ||||
| RsmMainAppVpdEntry | 1.3.6.1.4.1.2.3.51.2.2.21.7.1.1 | NA | deprecated | |
row · not-accessible · deprecated Switch module main application VPD table entry
| ||||
| CsmMainAppVpdIndex | 1.3.6.1.4.1.2.3.51.2.2.21.7.1.1.1 | INTEGER | RO | deprecated |
column · INTEGER · read-only · deprecated Switch module main application VPD entry index. | ||||
| CsmMainAppVpdId | 1.3.6.1.4.1.2.3.51.2.2.21.7.1.1.2 | INTEGER | RO | deprecated |
column · INTEGER · read-only · deprecated The switch module numeric identifier.
| ||||
| CsmMainAppVpdExists | 1.3.6.1.4.1.2.3.51.2.2.21.7.1.1.3 | INTEGER | RO | deprecated |
column · INTEGER · read-only · deprecated Indicates whether the switch module specified exists or not.
| ||||
| CsmMainAppVpdSwitchType | 1.3.6.1.4.1.2.3.51.2.2.21.7.1.1.4 | INTEGER | RO | deprecated |
column · INTEGER · read-only · deprecated Indicates the type of switch module installed.
| ||||
| CsmMainApp1VpdBuildId | 1.3.6.1.4.1.2.3.51.2.2.21.7.1.1.5 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Switch module firmware build id. | ||||
| CsmMainApp1VpdBuildDate | 1.3.6.1.4.1.2.3.51.2.2.21.7.1.1.6 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Switch module firmware build date. | ||||
| CsmMainApp1VpdRevisionNumber | 1.3.6.1.4.1.2.3.51.2.2.21.7.1.1.7 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Switch module firmware revision number. | ||||
| CsmMainApp2VpdBuildId | 1.3.6.1.4.1.2.3.51.2.2.21.7.1.1.8 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Switch module firmware build id. | ||||
| CsmMainApp2VpdBuildDate | 1.3.6.1.4.1.2.3.51.2.2.21.7.1.1.9 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Switch module firmware build date. | ||||
| CsmMainApp2VpdRevisionNumber | 1.3.6.1.4.1.2.3.51.2.2.21.7.1.1.10 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Switch module firmware revision number. | ||||
| CsmMainApp3VpdBuildId | 1.3.6.1.4.1.2.3.51.2.2.21.7.1.1.11 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated I/O Module firmware build id. | ||||
| CsmMainApp3VpdBuildDate | 1.3.6.1.4.1.2.3.51.2.2.21.7.1.1.12 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated I/O Module firmware build date. | ||||
| CsmMainApp3VpdRevisionNumber | 1.3.6.1.4.1.2.3.51.2.2.21.7.1.1.13 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated I/O Module firmware revision number. | ||||
| CsmMainAppVpdSwitchSubType | 1.3.6.1.4.1.2.3.51.2.2.21.7.1.1.20 | INTEGER | RO | deprecated |
column · INTEGER · read-only · deprecated Indicates the subtype of switch module installed.
| ||||
| TsmBootRomVpdTable | 1.3.6.1.4.1.2.3.51.2.2.21.7.2 | NA | deprecated | |
table · not-accessible · deprecated Switch module boot ROM VPD information table. | ||||
| RsmBootRomVpdEntry | 1.3.6.1.4.1.2.3.51.2.2.21.7.2.1 | NA | deprecated | |
| CsmBootRomVpdIndex | 1.3.6.1.4.1.2.3.51.2.2.21.7.2.1.1 | INTEGER | RO | deprecated |
column · INTEGER · read-only · deprecated Switch module boot ROM VPD entry index. | ||||
| CsmBootRomVpdId | 1.3.6.1.4.1.2.3.51.2.2.21.7.2.1.2 | INTEGER | RO | deprecated |
column · INTEGER · read-only · deprecated The switch module numeric identifier.
| ||||
| CsmBootRomVpdExists | 1.3.6.1.4.1.2.3.51.2.2.21.7.2.1.3 | INTEGER | RO | deprecated |
column · INTEGER · read-only · deprecated Indicates whether the switch module specified exists or not.
| ||||
| CsmBootRomVpdSwitchType | 1.3.6.1.4.1.2.3.51.2.2.21.7.2.1.4 | INTEGER | RO | deprecated |
column · INTEGER · read-only · deprecated Indicates the type of switch module installed.
| ||||
| CsmBootRomVpdBuildId | 1.3.6.1.4.1.2.3.51.2.2.21.7.2.1.5 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Switch module firmware build ID. | ||||
| CsmBootRomVpdBuildDate | 1.3.6.1.4.1.2.3.51.2.2.21.7.2.1.6 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Switch module firmware build date. | ||||
| CsmBootRomVpdRevisionNumber | 1.3.6.1.4.1.2.3.51.2.2.21.7.2.1.7 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Switch module firmware revision number. | ||||
| CsmBootRomVpdSwitchSubType | 1.3.6.1.4.1.2.3.51.2.2.21.7.2.1.8 | INTEGER | RO | deprecated |
column · INTEGER · read-only · deprecated Indicates the subtype of switch module installed.
| ||||
| NpmHardwareVpd | 1.3.6.1.4.1.2.3.51.2.2.21.8 | |||
| TpmHardwareVpdTable | 1.3.6.1.4.1.2.3.51.2.2.21.8.1 | NA | deprecated | |
table · not-accessible · deprecated Table of the power module hardware components. For consistent results, view as a table and not as individual entries. | ||||
| RpmHardwareVpdEntry | 1.3.6.1.4.1.2.3.51.2.2.21.8.1.1 | NA | deprecated | |
row · not-accessible · deprecated Power module hardware VPD entry. For consistent results, view as a table and not as individual entries.
| ||||
| CpmHardwareVpdIndex | 1.3.6.1.4.1.2.3.51.2.2.21.8.1.1.1 | INTEGER | RO | deprecated |
column · INTEGER · read-only · deprecated Power module hardware VPD index. For consistent results, view as a table and not as individual entries. | ||||
| CpmHardwareVpdBayNumber | 1.3.6.1.4.1.2.3.51.2.2.21.8.1.1.2 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Power module hardware VPD Bay number. For consistent results, view as a table and not as individual entries. | ||||
| CpmHardwareVpdManufacturingId | 1.3.6.1.4.1.2.3.51.2.2.21.8.1.1.3 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Power module hardware VPD manufacturing ID. For consistent results, view as a table and not as individual entries. | ||||
| CpmHardwareVpdFruNumber | 1.3.6.1.4.1.2.3.51.2.2.21.8.1.1.4 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Power module hardware VPD FRU number. For consistent results, view as a table and not as individual entries. | ||||
| CpmHardwareVpdHardwareRevision | 1.3.6.1.4.1.2.3.51.2.2.21.8.1.1.5 | INTEGER | RO | deprecated |
column · INTEGER · read-only · deprecated Power module hardware VPD hardware revision. For consistent results, view as a table and not as individual entries. If a hardware revision is programmed in the OEM VPD area for this component, then the HardwareRevisionString version of this MIB object should be used. | ||||
| CpmHardwareVpdUuid | 1.3.6.1.4.1.2.3.51.2.2.21.8.1.1.8 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Power module hardware VPD UUID. For consistent results, view as a table and not as individual entries. | ||||
| CpmHardwareVpdManufDate | 1.3.6.1.4.1.2.3.51.2.2.21.8.1.1.9 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Power module hardware VPD Manufacture Date. For consistent results, view as a table and not as individual entries. | ||||
| CpmHardwareVpdPartNumber | 1.3.6.1.4.1.2.3.51.2.2.21.8.1.1.10 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Power module hardware VPD Part Number. For consistent results, view as a table and not as individual entries. | ||||
| CpmHardwareVpdFruSerial | 1.3.6.1.4.1.2.3.51.2.2.21.8.1.1.11 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Power module hardware VPD FRU Serial. For consistent results, view as a table and not as individual entries. | ||||
| CpmHardwareVpdManufacturingIDNumber | 1.3.6.1.4.1.2.3.51.2.2.21.8.1.1.12 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Power module hardware VPD manufacturer ID. For consistent results, view as a table and not as individual entries. | ||||
| CpmHardwareVpdProductId | 1.3.6.1.4.1.2.3.51.2.2.21.8.1.1.13 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Power module hardware VPD product ID. For consistent results, view as a table and not as individual entries. | ||||
| CpmHardwareVpdSubManufacturerId | 1.3.6.1.4.1.2.3.51.2.2.21.8.1.1.14 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Power module hardware VPD subsystem manufacturer ID. For consistent results, view as a table and not as individual entries. | ||||
| CpmHardwareVpdClei | 1.3.6.1.4.1.2.3.51.2.2.21.8.1.1.15 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Power module hardware VPD Common Language Equipment Identifier (CLEI). For consistent results, view as a table and not as individual entries. | ||||
| CpmHardwareVpdHardwareRevisionString | 1.3.6.1.4.1.2.3.51.2.2.21.8.1.1.16 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Power module hardware VPD hardware revision in string format. For consistent results, view as a table and not as individual entries. If a hardware revision is programmed in the OEM VPD area for this component, then this MIB object should be used. | ||||
| NrearLEDCardHardwareVpd | 1.3.6.1.4.1.2.3.51.2.2.21.9 | |||
| SrearLEDCardHardwareVpdManufacturingId | 1.3.6.1.4.1.2.3.51.2.2.21.9.3 | OCTET STRING | RO | deprecated |
scalar · OCTET STRING · read-only · deprecated Rear LED card hardware VPD manufacturing ID. For consistent results, view as a table and not as individual entries. | ||||
| SrearLEDCardHardwareVpdFruNumber | 1.3.6.1.4.1.2.3.51.2.2.21.9.4 | OCTET STRING | RO | deprecated |
scalar · OCTET STRING · read-only · deprecated Rear LED card hardware VPD FRU number. For consistent results, view as a table and not as individual entries. | ||||
| SrearLEDCardHardwareVpdHardwareRevision | 1.3.6.1.4.1.2.3.51.2.2.21.9.5 | INTEGER | RO | deprecated |
scalar · INTEGER · read-only · deprecated Rear LED card hardware VPD hardware revision. For consistent results, view as a table and not as individual entries. If a hardware revision is programmed in the OEM VPD area for this component, then the HardwareRevisionString version of this MIB object should be used. | ||||
| SrearLEDCardHardwareVpdUuid | 1.3.6.1.4.1.2.3.51.2.2.21.9.8 | OCTET STRING | RO | deprecated |
scalar · OCTET STRING · read-only · deprecated Rear LED card hardware VPD UUID. For consistent results, view as a table and not as individual entries. | ||||
| SrearLEDCardHardwareVpdManufacturingIDNumber | 1.3.6.1.4.1.2.3.51.2.2.21.9.9 | OCTET STRING | RO | deprecated |
scalar · OCTET STRING · read-only · deprecated Rear LED card hardware VPD manufacturer ID. For consistent results, view as a table and not as individual entries. | ||||
| SrearLEDCardHardwareVpdProductId | 1.3.6.1.4.1.2.3.51.2.2.21.9.10 | OCTET STRING | RO | deprecated |
scalar · OCTET STRING · read-only · deprecated Rear LED card hardware VPD product ID. For consistent results, view as a table and not as individual entries. | ||||
| SrearLEDCardHardwareVpdSubManufacturerId | 1.3.6.1.4.1.2.3.51.2.2.21.9.11 | OCTET STRING | RO | deprecated |
scalar · OCTET STRING · read-only · deprecated Rear LED card hardware VPD subsystem manufacturer ID. For consistent results, view as a table and not as individual entries. | ||||
| SrearLEDCardHardwareVpdClei | 1.3.6.1.4.1.2.3.51.2.2.21.9.12 | OCTET STRING | RO | deprecated |
scalar · OCTET STRING · read-only · deprecated Rear LED card hardware VPD Common Language Equipment Identifier (CLEI). For consistent results, view as a table and not as individual entries. | ||||
| SrearLEDCardHardwareVpdHardwareRevisionString | 1.3.6.1.4.1.2.3.51.2.2.21.9.17 | OCTET STRING | RO | deprecated |
scalar · OCTET STRING · read-only · deprecated Rear LED card hardware VPD hardware revision in string format. For consistent results, view as a table and not as individual entries. If a hardware revision is programmed in the OEM VPD area for this component, then this MIB object should be used. | ||||
| SrearLEDCardHardwareVpdManufDate | 1.3.6.1.4.1.2.3.51.2.2.21.9.18 | OCTET STRING | RO | deprecated |
scalar · OCTET STRING · read-only · deprecated Rear LED card hardware VPD Manufacture Date. | ||||
| SrearLEDCardHardwareVpdPartNumber | 1.3.6.1.4.1.2.3.51.2.2.21.9.19 | OCTET STRING | RO | deprecated |
scalar · OCTET STRING · read-only · deprecated Rear LED card hardware VPD Part Number. | ||||
| SrearLEDCardHardwareVpdFruSerial | 1.3.6.1.4.1.2.3.51.2.2.21.9.20 | OCTET STRING | RO | deprecated |
scalar · OCTET STRING · read-only · deprecated Rear LED card hardware VPD FRU Serial. | ||||
| NchassisFanFirmwareVpd | 1.3.6.1.4.1.2.3.51.2.2.21.12 | |||
| TchassisFanControllerVPDTable | 1.3.6.1.4.1.2.3.51.2.2.21.12.1 | NA | deprecated | |
table · not-accessible · deprecated Table of chassis fan controller firmware vital product data (VPD) information. | ||||
| RchassisFanControllerVPDEntry | 1.3.6.1.4.1.2.3.51.2.2.21.12.1.1 | NA | deprecated | |
row · not-accessible · deprecated Chassis fan controller firmware VPD table entry | ||||
| CchassisFanControllerVpdIndex | 1.3.6.1.4.1.2.3.51.2.2.21.12.1.1.1 | INTEGER | RO | deprecated |
column · INTEGER · read-only · deprecated Chassis fan controller firmware VPD table index. | ||||
| CchassisFanControllerVpdId | 1.3.6.1.4.1.2.3.51.2.2.21.12.1.1.2 | INTEGER | RO | deprecated |
column · INTEGER · read-only · deprecated The numeric chassis fan ID.
| ||||
| CchassisFanControllerVpdExists | 1.3.6.1.4.1.2.3.51.2.2.21.12.1.1.3 | INTEGER | RO | deprecated |
column · INTEGER · read-only · deprecated Indicates whether the chassis fan specified exists or not.
| ||||
| CchassisFanControllerVpdRevision | 1.3.6.1.4.1.2.3.51.2.2.21.12.1.1.7 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated The revision of the chassis fan controller firmware. | ||||
| NchassisFanHardwareVpd | 1.3.6.1.4.1.2.3.51.2.2.21.13 | |||
| TchassisFanHardwareVpdTable | 1.3.6.1.4.1.2.3.51.2.2.21.13.1 | NA | deprecated | |
table · not-accessible · deprecated Table of the chassis fan hardware components. | ||||
| RchassisFanHardwareVpdEntry | 1.3.6.1.4.1.2.3.51.2.2.21.13.1.1 | NA | deprecated | |
| CchassisFanHardwareVpdIndex | 1.3.6.1.4.1.2.3.51.2.2.21.13.1.1.1 | INTEGER | RO | deprecated |
column · INTEGER · read-only · deprecated Chassis fan hardware VPD index. | ||||
| CchassisFanHardwareVpdBayNumber | 1.3.6.1.4.1.2.3.51.2.2.21.13.1.1.2 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Chassis fan hardware VPD Bay number. | ||||
| CchassisFanHardwareVpdManufacturingId | 1.3.6.1.4.1.2.3.51.2.2.21.13.1.1.3 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Chassis fan hardware VPD manufacturing ID. | ||||
| CchassisFanHardwareVpdFruNumber | 1.3.6.1.4.1.2.3.51.2.2.21.13.1.1.4 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Chassis fan hardware VPD FRU number. | ||||
| CchassisFanHardwareVpdHardwareRevision | 1.3.6.1.4.1.2.3.51.2.2.21.13.1.1.5 | INTEGER | RO | deprecated |
column · INTEGER · read-only · deprecated Chassis fan hardware VPD hardware revision. | ||||
| CchassisFanHardwareVpdUuid | 1.3.6.1.4.1.2.3.51.2.2.21.13.1.1.8 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Chassis fan hardware VPD UUID. | ||||
| CchassisFanHardwareVpdManufDate | 1.3.6.1.4.1.2.3.51.2.2.21.13.1.1.9 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Chassis fan hardware VPD manufacture Date. | ||||
| CchassisFanHardwareVpdPartNumber | 1.3.6.1.4.1.2.3.51.2.2.21.13.1.1.10 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Chassis fan hardware VPD Part Number. | ||||
| CchassisFanHardwareVpdFruSerial | 1.3.6.1.4.1.2.3.51.2.2.21.13.1.1.11 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Chassis fan hardware VPD FRU serial number. | ||||
| CchassisFanHardwareVpdManufacturingIDNumber | 1.3.6.1.4.1.2.3.51.2.2.21.13.1.1.12 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Chassis fan hardware VPD manufacturer ID. | ||||
| CchassisFanHardwareVpdProductId | 1.3.6.1.4.1.2.3.51.2.2.21.13.1.1.13 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Chassis fan hardware VPD product ID. | ||||
| CchassisFanHardwareVpdSubManufacturerId | 1.3.6.1.4.1.2.3.51.2.2.21.13.1.1.14 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Chassis fan hardware VPD subsystem manufacturer ID. | ||||
| CchassisFanHardwareVpdClei | 1.3.6.1.4.1.2.3.51.2.2.21.13.1.1.15 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Chassis fan hardware VPD Common Language Equipment Identifier (CLEI). | ||||
| CchassisFanHardwareVpdHardwareRevisionString | 1.3.6.1.4.1.2.3.51.2.2.21.13.1.1.16 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated Chassis fan hardware VPD hardware revision in string format. | ||||
| NpmFirmwareVpd | 1.3.6.1.4.1.2.3.51.2.2.21.14 | |||
| TpmControllerVPDTable | 1.3.6.1.4.1.2.3.51.2.2.21.14.1 | NA | deprecated | |
table · not-accessible · deprecated Table of Power Module controller firmware vital product data (VPD) information. | ||||
| RpmControllerVPDEntry | 1.3.6.1.4.1.2.3.51.2.2.21.14.1.1 | NA | deprecated | |
row · not-accessible · deprecated Power Module controller firmware VPD table entry
| ||||
| CpmControllerVpdIndex | 1.3.6.1.4.1.2.3.51.2.2.21.14.1.1.1 | INTEGER | RO | deprecated |
column · INTEGER · read-only · deprecated Power Module controller firmware VPD table index. | ||||
| CpmControllerVpdId | 1.3.6.1.4.1.2.3.51.2.2.21.14.1.1.2 | INTEGER | RO | deprecated |
column · INTEGER · read-only · deprecated The numeric Power Module ID.
| ||||
| CpmControllerVpdExists | 1.3.6.1.4.1.2.3.51.2.2.21.14.1.1.3 | INTEGER | RO | deprecated |
column · INTEGER · read-only · deprecated Indicates whether the Power Module specified exists or not.
| ||||
| CpmControllerVpdRevision | 1.3.6.1.4.1.2.3.51.2.2.21.14.1.1.7 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated The revision of the Power Module controller firmware. | ||||
| TinventoryManagementActivityVpdTable | 1.3.6.1.4.1.2.3.51.2.2.21.22 | NA | mandatory | |
table · not-accessible · mandatory Table of system component hardware VPD activity log. For consistent results, view as a table and not as individual entries. | ||||
| RinventoryManagementActivityVpdEntry | 1.3.6.1.4.1.2.3.51.2.2.21.22.1 | NA | mandatory | |
row · not-accessible · mandatory System component hardware VPD activity log entry. For consistent results, view as a table and not as individual entries. | ||||
| CcomponentLevelActivityVpdIndex | 1.3.6.1.4.1.2.3.51.2.2.21.22.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory System component level VPD activity log index. For consistent results, view as a table and not as individual entries. | ||||
| CcomponentLevelActivityVpdFruNumber | 1.3.6.1.4.1.2.3.51.2.2.21.22.1.2 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory System component level VPD activity log FRU number. For consistent results, view as a table and not as individual entries. | ||||
| CcomponentLevelActivityVpdSerialNumber | 1.3.6.1.4.1.2.3.51.2.2.21.22.1.3 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory System component level VPD activity log serial number. For consistent results, view as a table and not as individual entries. | ||||
| CcomponentLevelActivityVpdManufacturingId | 1.3.6.1.4.1.2.3.51.2.2.21.22.1.4 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory System component level VPD activity log manufacturing ID. For consistent results, view as a table and not as individual entries. | ||||
| CcomponentLevelActivityVpdBayNumber | 1.3.6.1.4.1.2.3.51.2.2.21.22.1.5 | OCTET STRING | RO | deprecated |
column · OCTET STRING · read-only · deprecated System component level VPD activity log Bay number. For consistent results, view as a table and not as individual entries. | ||||
| CcomponentLevelActivityVpdAction | 1.3.6.1.4.1.2.3.51.2.2.21.22.1.9 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory System component level VPD activity log action (added/removed). For consistent results, view as a table and not as individual entries. | ||||
| CcomponentLevelActivityVpdTimestamp | 1.3.6.1.4.1.2.3.51.2.2.21.22.1.10 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory System component level VPD activity log timestamp. For consistent results, view as a table and not as individual entries. | ||||
| CcomponentLevelActivityVpdModuleName | 1.3.6.1.4.1.2.3.51.2.2.21.22.1.12 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The module name which this row is associated with. For consistent results, view as a table and not as individual entries. | ||||
| CcomponentLevelActivityVpdTopologyPath | 1.3.6.1.4.1.2.3.51.2.2.21.22.1.15 | OCTET STRING (SIZE (0..100)) | RO | mandatory |
column · OCTET STRING (SIZE (0..100)) · read-only · mandatory The chassis and each installed component is represented by a hardware topology tree, where each node in the tree represents a component. As an example, the root of the tree is the chassis and is represented by the pair 'CHASSIS, 1'. This pair indicates the first instance of the chassis. If a blade is inserted in slot 4 of the chassis, its topology path is 'CHASSIS, 1, BLADE, 4'. With this format, the components in the chassis can be determined along with their relative hierarchy to each other. The topology path's numeric designations for the components are: CHASSIS, 0x01 Chassis MM, 0x02 Management Module BLADE, 0x03 Main system board of a blade POWER, 0x04 Power Supply, Power Module, etc COOLING, 0x05 Fan, blower, or other cooling device IO_MODULE, 0x06 Has I/O interface, i.e. - switch or bridge MEDIA, 0x07 Media device PROCESSOR, 0x08 Any processor, processor module, etc STORAGE, 0x09 Any type of storage device EXPANSION, 0x0A Expansion Card (not covered by more specific type) MEMORY, 0x0B Any memory device, module, etc MFRU, 0x0C Managed FRU Device PANEL, 0x0D Any sort of panel device, such as a front panel BLADE_EXPANSION_MODULE, 0x0E Expansion option (BEM) such as PEU, BSE, etc CARD_EXPANSION, 0x0F Expansion card, ie. daughter card CARD_HS_EXPANSION, 0x10 High Speed Expansion card, ie. daughter card INTERPOSER, 0x11 Interposer device CLOCK, 0x12 Clock card MUX, 0x13 Mulitplexer card ADDIN, 0x14 cKVM card & other addin cards STORAGE_MODULE, 0x15 Container of one or more Storage Devices SYS_EXPANSION_CARD, 0x16 Management card BATTERY, 0x17 A single battery BATTERY_MODULE, 0x18 Container of one or more batteries REAR_LED, 0x19 Rear LED card MEMORY_BANK, 0x1A Memory banks AIR_FILTER, 0x1B Filter mechanism (bezel) SERIAL_PORT_MODULE, 0x1C Container of one or more serial ports PARENT, 0x1D Reference to parent for multi-parent support PHY_PORT, 0x1E Physical port IO_EXPANDER, 0x1F RAID card CABLE, 0x20 Cable/Interconnect FAN_MUX, 0x29 Fan multiplexer card PCI_EXPRESS, 0x32 PCI express card on (PEN) FLASH_DIMM, 0x33 Used for SPD devices that matches the silkscreen of the DIMM slot RACK, 0x50 Rack PLATFORM, 0x51 Generic Platform like rack mounted server/appliance DATAPLEX, 0x52 DataPlex OTHER, 0x53 Other unknown etc. PERIPHERAL_MODULE, 0x54 SYSTEM_BOARD, 0x55 System board PROCESSOR_MODULE, 0x56 BACK_PANEL, 0x57 POWER_SYSTEM_BOARD, 0x58 STORAGE_BACKPLANE, 0x59 Drive back plane PROC_BOARD, 0x5A Holds 1 or more processors POWER_DI, 0x5B Power mgt / power distribution board CHASSIS_BACK_PANEL, 0x5C SUB_CHASSIS, 0x5D OTHER_CHASSIS_BOARD, 0x5E DEVICE_MODULE, 0x5F REMOTE_DEVICE, 0x60 Remote mgt communication device EXTERNAL_ENVIRONMENT, 0x61 Such as external temp sensor for outside box temps PROC_MEMORY_MODULE, 0x62 Processors and memory on same module | ||||
| NreloadVpdData | 1.3.6.1.4.1.2.3.51.2.2.21.23 | |||
| SreloadAllVpdData | 1.3.6.1.4.1.2.3.51.2.2.21.23.1 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Reload all VPD data (firmware, hardware, MAC address, WWN/GUID and other Unique ID). NOTE: The value returned for the GET command is meaningless.
| ||||
| SreloadFwVpdData | 1.3.6.1.4.1.2.3.51.2.2.21.23.2 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Reload firmware VPD data. NOTE: The value returned for the GET command is meaningless.
| ||||
| SreloadHwVpdData | 1.3.6.1.4.1.2.3.51.2.2.21.23.3 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Reload hardware VPD data. NOTE: The value returned for the GET command is meaningless.
| ||||
| SreloadMACAddress | 1.3.6.1.4.1.2.3.51.2.2.21.23.4 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Reload blade MAC addresses. NOTE: The value returned for the GET command is meaningless.
| ||||
| SreloadWwnGuidVpdData | 1.3.6.1.4.1.2.3.51.2.2.21.23.5 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Reload blade and I/O module WWN/GUID and other VPD data. NOTE: The value returned for the GET command is meaningless.
| ||||
| NairFilter | 1.3.6.1.4.1.2.3.51.2.2.22 | |||
| NpassiveAirFilter | 1.3.6.1.4.1.2.3.51.2.2.22.1 | |||
| SpassiveAirFilterStatus | 1.3.6.1.4.1.2.3.51.2.2.22.1.1 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Disable/Enable/Reset the passive air filter. When enabled, sending an enable or reset will reset the replace date.
| ||||
| SpassiveAirFilterMonthFreq | 1.3.6.1.4.1.2.3.51.2.2.22.1.2 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory The chassis environment. 1 month indicates high dust, 3 months indicates moderate dust and, 6 months indicates low dust.
| ||||
| SpassiveAirFilterReplaceDate | 1.3.6.1.4.1.2.3.51.2.2.22.1.3 | OCTET STRING (SIZE (0..30)) | RO | mandatory |
scalar · OCTET STRING (SIZE (0..30)) · read-only · mandatory The scheduled replacement date of the air filter. | ||||
| NcomponentInformation | 1.3.6.1.4.1.2.3.51.2.2.23 | |||
| NcomponentInventory | 1.3.6.1.4.1.2.3.51.2.2.23.1 | |||
| TcomponentInventoryTable | 1.3.6.1.4.1.2.3.51.2.2.23.1.1 | NA | mandatory | |
table · not-accessible · mandatory Table of component inventory information. Not all components will provide every object defined in the ComponentInventoryEntry. Also, if a component does not have inventory information or the CMM is not able to read the data from the device, then there will not be a row in this table for the component. | ||||
| RcomponentInventoryEntry | 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1 | NA | mandatory | |
| CcomponentInventoryTopologyPath | 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.1 | OCTET STRING (SIZE (0..100)) | RO | mandatory |
column · OCTET STRING (SIZE (0..100)) · read-only · mandatory The unique identifier for a row in this table. The chassis and each installed component is represented by a hardware topology tree, where each node in the tree represents a component. The path to a particular component consists of one or more <component>,<instance> pairs, where each successive pair is a child of the previous parent pair. As an example, the root of the tree is the chassis and is represented by the pair 'CHASSIS, 1'. This pair indicates the first instance of the chassis. If a blade is inserted in slot 4 of the chassis, its topology path is 'CHASSIS, 1, BLADE, 4'. With this format, the components in the chassis can be determined along with their relative hierarchy to each other. This component inventory table is indexed by this unique topology path and the numeric designations for the components are: CHASSIS, 0x01 Chassis MM, 0x02 Management Module BLADE, 0x03 Main system board of a blade POWER, 0x04 Power Supply, Power Module, etc COOLING, 0x05 Fan, blower, or other cooling device IO_MODULE, 0x06 Has I/O interface, i.e. - switch or bridge MEDIA, 0x07 Media device PROCESSOR, 0x08 Any processor, processor module, etc STORAGE, 0x09 Any type of storage device EXPANSION, 0x0A Expansion Card (not covered by more specific type) MEMORY, 0x0B Any memory device, module, etc MFRU, 0x0C Managed FRU Device PANEL, 0x0D Any sort of panel device, such as a front panel BLADE_EXPANSION_MODULE, 0x0E Expansion option (BEM) such as PEU, BSE, etc CARD_EXPANSION, 0x0F Expansion card, ie. daughter card CARD_HS_EXPANSION, 0x10 High Speed Expansion card, ie. daughter card INTERPOSER, 0x11 Interposer device CLOCK, 0x12 Clock card MUX, 0x13 Mulitplexer card ADDIN, 0x14 cKVM card & other addin cards STORAGE_MODULE, 0x15 Container of one or more Storage Devices SYS_EXPANSION_CARD, 0x16 Management card BATTERY, 0x17 A single battery BATTERY_MODULE, 0x18 Container of one or more batteries REAR_LED, 0x19 Rear LED card MEMORY_BANK, 0x1A Memory banks AIR_FILTER, 0x1B Filter mechanism (bezel) SERIAL_PORT_MODULE, 0x1C Container of one or more serial ports PARENT, 0x1D Reference to parent for multi-parent support PHY_PORT, 0x1E Physical port IO_EXPANDER, 0x1F RAID card CABLE, 0x20 Cable/Interconnect FAN_MUX, 0x29 Fan multiplexer card PCI_EXPRESS, 0x32 PCI express card on (PEN) FLASH_DIMM, 0x33 Used for SPD devices that matches the silkscreen of the DIMM slot RACK, 0x50 Rack PLATFORM, 0x51 Generic Platform like rack mounted server/appliance DATAPLEX, 0x52 DataPlex OTHER, 0x53 Other unknown etc. PERIPHERAL_MODULE, 0x54 SYSTEM_BOARD, 0x55 System board PROCESSOR_MODULE, 0x56 BACK_PANEL, 0x57 POWER_SYSTEM_BOARD, 0x58 STORAGE_BACKPLANE, 0x59 Drive back plane PROC_BOARD, 0x5A Holds 1 or more processors POWER_DI, 0x5B Power mgt / power distribution board CHASSIS_BACK_PANEL, 0x5C SUB_CHASSIS, 0x5D OTHER_CHASSIS_BOARD, 0x5E DEVICE_MODULE, 0x5F REMOTE_DEVICE, 0x60 Remote mgt communication device EXTERNAL_ENVIRONMENT, 0x61 Such as external temp sensor for outside box temps PROC_MEMORY_MODULE, 0x62 Processors and memory on same module | ||||
| CcomponentInventoryInstance | 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The slot number or instance of a particular component. Typically, if the component plugs into the chassis, this represents the slot number. However, some components are connected to another component, and this represents the instance. For example, a blade may have several expansion cards that connect to the blade system planar, and in this case, this value identifies which expansion card instance the row represents. Note that this slot/instance value can be determined from the componentInventoryTopologyPath object, but this componentInventoryInstance object is provided as a convenience to the user. | ||||
| CcomponentInventoryDescription | 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.3 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory A short text string describing the particular component. If a text string is not available, a value of 'Not available' is presented. For more detail, also refer to the componentInventoryProductName object in this table or the componentXXXXName object of any of the other component tables under the 'components' section of the MIB. | ||||
| CcomponentInventoryMachineTypeModel | 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.4 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The machine type and model number of this component. Typically, the format is XXXXYYY, where XXXX reprsents the machine type and YYY represents the model number. | ||||
| CcomponentInventoryMachineSerial | 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.5 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The machine serial number of this component. | ||||
| CcomponentInventoryAssetID | 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.6 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The asset identifier of this component, typically set by some other authority than the manufacturer. | ||||
| CcomponentInventoryPartNumber | 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.7 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The part number of this component. | ||||
| CcomponentInventoryFRUNumber | 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.8 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The Field Replaceable Unit (FRU) number of this component. | ||||
| CcomponentInventoryFRUSerialNumber | 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.9 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The Field Replaceable Unit (FRU) serial number of this component. | ||||
| CcomponentInventoryManufacture | 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.10 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The text description of the manufacturer of this component. | ||||
| CcomponentInventoryHardwareRevision | 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.11 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The hardware revision number of the this component. | ||||
| CcomponentInventoryManufactureDate | 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.12 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The date when the manufacturer created this component. The format is XXYY, where XX is the week number of the year 20YY. | ||||
| CcomponentInventoryUUID | 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.13 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The Universally Unique IDentifier (UUID) of this component, represented as a 16 byte hex number. | ||||
| CcomponentInventoryProductID | 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.14 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The product identifier of the component assigned by the manufacturer. | ||||
| CcomponentInventorySubManufactureID | 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.15 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The text sub-description of the manufacturer of this component, often used to identify a supplier for a component which has multiple suppliers. | ||||
| CcomponentInventoryCLEI | 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.16 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The Common Language Equipment Identifier (CLEI) of this component. | ||||
| CcomponentInventoryAssetTag | 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.17 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The asset tag of this component. | ||||
| CcomponentInventorySpeed | 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.18 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory A speed designation for the component, for example, processor speed. | ||||
| CcomponentInventoryIdentifier | 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.19 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory A unique identifier assigned by the manufacturer to the component, for example, a processor ID. | ||||
| CcomponentInventorySize | 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.20 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory A size designation for the component, for example, a memory DIMM size or hard drive capacity. | ||||
| CcomponentInventoryMemoryType | 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.21 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The architecture specification of a memory device.
| ||||
| CcomponentInventoryProductName | 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.22 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The product name assigned by the manufacturer for this component. For more detail, also refer to the componentInventoryDescription object. | ||||
| CcomponentInventoryProductVersion | 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.23 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The product version assigned by the manufacturer for this component. | ||||
| CcomponentInventoryProcessorType | 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.24 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The type designation for processor components.
| ||||
| CcomponentInventoryProcessorFamily | 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.25 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The family designation for processor components. | ||||
| CcomponentInventoryProcessorCores | 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.26 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The number of cores present on a processor component. | ||||
| CcomponentInventoryProcessorThreads | 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.27 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The number of threads present on a processor component. | ||||
| CcomponentInventoryProcessorL1DCache | 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.28 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The level 1 data cache size of a processor component. | ||||
| CcomponentInventoryProcessorL1ICache | 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.29 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The level 1 instruction cache size of a processor component. | ||||
| CcomponentInventoryProcessorL2Cache | 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.30 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The level 2 cache size of a processor component. | ||||
| CcomponentInventoryProcessorL3Cache | 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.31 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The level 3 cache size of a processor component. | ||||
| CcomponentInventoryProcessorVoltage | 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.32 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The voltage rating for a processor component. | ||||
| CcomponentInventoryProcessorExtClock | 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.33 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The external clock speed of a processor component. | ||||
| CcomponentInventoryProcessorDataWidth | 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.34 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The maximum data bus width capability of a processor component, expressed typically in bits. | ||||
| CcomponentInventoryManufactureIDNum | 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.35 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The identification number assigned for the component by the manufacturer. | ||||
| CcomponentInventoryGlobalID | 1.3.6.1.4.1.2.3.51.2.2.23.1.1.1.41 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The global identifier (GLID) of this component. This ID is a unique identifier for the CMM chassis (midplane), set by the manufacturer. This ID and the associated inventory is passed back to IBM via the Electronic Service Agent and the Call Home feature. This ID and the accompanying chassis inventory will be stored and retained resulting in a configuration/change history file of the inventory for a chassis associated with a particular GLID. This ID can be used by a customer to identify and categorize all the content that resides within a chassis, much like a physical serial number is associated with a single box server. | ||||
| ScomponentInventoryTableCacheTimeout | 1.3.6.1.4.1.2.3.51.2.2.23.1.2 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory The timeout value (in seconds) of the cached data for the table, componentInventoryTable. This value is static (constant) and cannot be set. | ||||
| NcomponentFirmware | 1.3.6.1.4.1.2.3.51.2.2.23.2 | |||
| TcomponentFirmwareTable | 1.3.6.1.4.1.2.3.51.2.2.23.2.1 | NA | mandatory | |
table · not-accessible · mandatory Table of component firmware information. Not all components will provide every object defined in the ComponentFirmwareEntry. | ||||
| RcomponentFirmwareEntry | 1.3.6.1.4.1.2.3.51.2.2.23.2.1.1 | NA | mandatory | |
row · not-accessible · mandatory Component firmware information. | ||||
| CcomponentFirmwareTopologyPath | 1.3.6.1.4.1.2.3.51.2.2.23.2.1.1.1 | OCTET STRING (SIZE (0..100)) | RO | mandatory |
column · OCTET STRING (SIZE (0..100)) · read-only · mandatory The unique identifier for a component in this table. The chassis and each installed component is represented by a hardware topology tree, where each node in the tree represents a component. The path to a particular component consists of one or more <component>,<instance> pairs, where each successive pair is a child of the previous parent pair. As an example, the root of the tree is the chassis and is represented by the pair 'CHASSIS, 1'. This pair indicates the first instance of the chassis. If a blade is inserted in slot 4 of the chassis, its topology path is 'CHASSIS, 1, BLADE, 4'. With this format, the components in the chassis can be determined along with their relative hierarchy to each other. Note that this TP is preceded by a single octet that specifies the TP length. This is required since this table is indexed with two indices and, therefore, the TP length must be explicitly provided. This component firmware table is indexed by this unique topology path and the numeric designations for the components are: CHASSIS, 0x01 Chassis MM, 0x02 Management Module BLADE, 0x03 Main system board of a blade POWER, 0x04 Power Supply, Power Module, etc COOLING, 0x05 Fan, blower, or other cooling device IO_MODULE, 0x06 Has I/O interface, i.e. - switch or bridge MEDIA, 0x07 Media device PROCESSOR, 0x08 Any processor, processor module, etc STORAGE, 0x09 Any type of storage device EXPANSION, 0x0A Expansion Card (not covered by more specific type) MEMORY, 0x0B Any memory device, module, etc MFRU, 0x0C Managed FRU Device PANEL, 0x0D Any sort of panel device, such as a front panel BLADE_EXPANSION_MODULE, 0x0E Expansion option (BEM) such as PEU, BSE, etc CARD_EXPANSION, 0x0F Expansion card, ie. daughter card CARD_HS_EXPANSION, 0x10 High Speed Expansion card, ie. daughter card INTERPOSER, 0x11 Interposer device CLOCK, 0x12 Clock card MUX, 0x13 Mulitplexer card ADDIN, 0x14 cKVM card & other addin cards STORAGE_MODULE, 0x15 Container of one or more Storage Devices SYS_EXPANSION_CARD, 0x16 Management card BATTERY, 0x17 A single battery BATTERY_MODULE, 0x18 Container of one or more batteries REAR_LED, 0x19 Rear LED card MEMORY_BANK, 0x1A Memory banks AIR_FILTER, 0x1B Filter mechanism (bezel) SERIAL_PORT_MODULE, 0x1C Container of one or more serial ports PARENT, 0x1D Reference to parent for multi-parent support PHY_PORT, 0x1E Physical port IO_EXPANDER, 0x1F RAID card CABLE, 0x20 Cable/Interconnect FAN_MUX, 0x29 Fan multiplexer card PCI_EXPRESS, 0x32 PCI express card on (PEN) FLASH_DIMM, 0x33 Used for SPD devices that matches the silkscreen of the DIMM slot RACK, 0x50 Rack PLATFORM, 0x51 Generic Platform like rack mounted server/appliance DATAPLEX, 0x52 DataPlex OTHER, 0x53 Other unknown etc. PERIPHERAL_MODULE, 0x54 SYSTEM_BOARD, 0x55 System board PROCESSOR_MODULE, 0x56 BACK_PANEL, 0x57 POWER_SYSTEM_BOARD, 0x58 STORAGE_BACKPLANE, 0x59 Drive back plane PROC_BOARD, 0x5A Holds 1 or more processors POWER_DI, 0x5B Power mgt / power distribution board CHASSIS_BACK_PANEL, 0x5C SUB_CHASSIS, 0x5D OTHER_CHASSIS_BOARD, 0x5E DEVICE_MODULE, 0x5F REMOTE_DEVICE, 0x60 Remote mgt communication device EXTERNAL_ENVIRONMENT, 0x61 Such as external temp sensor for outside box temps PROC_MEMORY_MODULE, 0x62 Processors and memory on same module | ||||
| CcomponentFirmwareIndex | 1.3.6.1.4.1.2.3.51.2.2.23.2.1.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Each component may have one or more types of firmware associated with it, and this index object identifies the particular instance. | ||||
| CcomponentFirmwareComponentInstance | 1.3.6.1.4.1.2.3.51.2.2.23.2.1.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The slot number or instance of a particular component. Typically, if the component plugs into the chassis, this represents the slot number. However, some components are connected to another component, and this represents the instance. For example, a blade may have several expansion cards that connect to the blade system planar, and in this case, this value identifies which expansion card instance the row represents. Note that this slot/instance value can be determined from the componentFirmwareTopologyPath object, but this componentFirmwareComponentInstance object is provided as a convenience to the user. | ||||
| CcomponentFirmwareComponentDescription | 1.3.6.1.4.1.2.3.51.2.2.23.2.1.1.4 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory A short text string describing the particular component. For the MM and blades, this name will be the configured name or its serial number if no user configured name is available. For all other components, this object will provide text to identify the component. If a text string is not available, a value of 'Not available' is presented. For more detail, also refer to the componentInventoryProductName object. | ||||
| CcomponentFirmwareType | 1.3.6.1.4.1.2.3.51.2.2.23.2.1.1.5 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory A text description of the type of firmware load. | ||||
| CcomponentFirmwareBuildID | 1.3.6.1.4.1.2.3.51.2.2.23.2.1.1.6 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory A text description of the build identifier for this firmware load. | ||||
| CcomponentFirmwareReleaseDate | 1.3.6.1.4.1.2.3.51.2.2.23.2.1.1.7 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory A text description of the release date for this firmware load. | ||||
| CcomponentFirmwareFilename | 1.3.6.1.4.1.2.3.51.2.2.23.2.1.1.8 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory A text description of the filename of this firmware load. | ||||
| CcomponentFirmwareRevision | 1.3.6.1.4.1.2.3.51.2.2.23.2.1.1.9 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory A text description of the revision level of this firmware load. | ||||
| CcomponentFirmwareRevisionMajor | 1.3.6.1.4.1.2.3.51.2.2.23.2.1.1.10 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory A numeric identifier of the revision major number for this firmware load. | ||||
| CcomponentFirmwareRevisionMinor | 1.3.6.1.4.1.2.3.51.2.2.23.2.1.1.11 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory A numeric identifier of the revision minor number for this firmware load. | ||||
| CcomponentFirmwareLevelStatus | 1.3.6.1.4.1.2.3.51.2.2.23.2.1.1.12 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The level status of the firmware build ID. It has three possible values as Different (mismatch firmware build ID), Match (the same firmware build ID), Unique (only one such firmware build ID). | ||||
| CcomponentFirmwarePendingBuildID | 1.3.6.1.4.1.2.3.51.2.2.23.2.1.1.13 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory A text description of the build identifier for this pending firmware load. | ||||
| CcomponentFirmwarePendingReleaseDate | 1.3.6.1.4.1.2.3.51.2.2.23.2.1.1.14 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory A text description of the release date for this pending firmware load. | ||||
| CcomponentFirmwarePendingRevision | 1.3.6.1.4.1.2.3.51.2.2.23.2.1.1.15 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory A text description of the revision level of this pending firmware load. | ||||
| CcomponentFirmwareReleaseLevel | 1.3.6.1.4.1.2.3.51.2.2.23.2.1.1.16 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory A text description of the firmware release level this firmware load. | ||||
| CcomponentFirmwareImageStatus | 1.3.6.1.4.1.2.3.51.2.2.23.2.1.1.17 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This object indicates whether this firmware image is the active (1) firmware,otherwise this firmware image is inactive (0).
| ||||
| CcomponentFirmwareRole | 1.3.6.1.4.1.2.3.51.2.2.23.2.1.1.18 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory A text description with the firmware image information. | ||||
| CcomponentFirmwareTypeID | 1.3.6.1.4.1.2.3.51.2.2.23.2.1.1.20 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates the type of firmware load with a numeric identifier.
| ||||
| ScomponentFirmwareTableCacheTimeout | 1.3.6.1.4.1.2.3.51.2.2.23.2.2 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory The timeout value (in seconds) of the cached data for the table, componentFirmwareTable. This value is static (constant) and cannot be set. | ||||
| TnodeFirmwareAnalysisTable | 1.3.6.1.4.1.2.3.51.2.2.23.2.7 | NA | mandatory | |
table · not-accessible · mandatory Table of firmware levels of installed nodes. This information is grouped by Machine Type/Model and includes two or more nodes with the same Type/Model. This information is intended to be used in determining which components firmware may need upgrade. | ||||
| RnodeFirmwareAnalysisEntry | 1.3.6.1.4.1.2.3.51.2.2.23.2.7.1 | NA | mandatory | |
| CnodeFirmwareAnalysisIndex | 1.3.6.1.4.1.2.3.51.2.2.23.2.7.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The index for the node firmware levels. | ||||
| CnodeFirmwareAnalysisMachineTypeModel | 1.3.6.1.4.1.2.3.51.2.2.23.2.7.1.2 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The machine type or model of node firmware. | ||||
| CnodeFirmwareAnalysisFirmwareType | 1.3.6.1.4.1.2.3.51.2.2.23.2.7.1.3 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The firmware type. | ||||
| CnodeFirmwareAnalysisBuildId | 1.3.6.1.4.1.2.3.51.2.2.23.2.7.1.4 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The firmware build id. | ||||
| CnodeFirmwareAnalysisReleaseDate | 1.3.6.1.4.1.2.3.51.2.2.23.2.7.1.5 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The firmware release date. | ||||
| CnodeFirmwareAnalysisRevisionLevel | 1.3.6.1.4.1.2.3.51.2.2.23.2.7.1.6 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The firmware revision level. | ||||
| CnodeFirmwareAnalysisTopology | 1.3.6.1.4.1.2.3.51.2.2.23.2.7.1.7 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The node topology. | ||||
| CnodeFirmwareAnalysisDeviceName | 1.3.6.1.4.1.2.3.51.2.2.23.2.7.1.8 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The node device name. | ||||
| TsmFirmwareAnalysisTable | 1.3.6.1.4.1.2.3.51.2.2.23.2.11 | NA | mandatory | |
table · not-accessible · mandatory Table of firmware levels of installed IOMs. This information is grouped by Product Id and includes two or more IOMs with the same product id. This information is intended to be used in determining which components firmware may need upgrade. | ||||
| RsmFirmwareAnalysisEntry | 1.3.6.1.4.1.2.3.51.2.2.23.2.11.1 | NA | mandatory | |
| CsmFirmwareAnalysisIndex | 1.3.6.1.4.1.2.3.51.2.2.23.2.11.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The index for the IOM firmware levels. | ||||
| CsmFirmwareAnalysisProductId | 1.3.6.1.4.1.2.3.51.2.2.23.2.11.1.2 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The IOM product id. | ||||
| CsmFirmwareAnalysisProductName | 1.3.6.1.4.1.2.3.51.2.2.23.2.11.1.3 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The IOM product name. | ||||
| CsmFirmwareAnalysisFirmwareType | 1.3.6.1.4.1.2.3.51.2.2.23.2.11.1.4 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The IOM firmware type. | ||||
| CsmFirmwareAnalysisFirmwareVersion | 1.3.6.1.4.1.2.3.51.2.2.23.2.11.1.5 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The IOM firmware version. | ||||
| CsmFirmwareAnalysisReleaseDate | 1.3.6.1.4.1.2.3.51.2.2.23.2.11.1.6 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The IOM release date. | ||||
| CsmFirmwareAnalysisTopology | 1.3.6.1.4.1.2.3.51.2.2.23.2.11.1.7 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The IOM topology. | ||||
| ScomponentInventoryReady | 1.3.6.1.4.1.2.3.51.2.2.23.3 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory When a blade management controller, switch or the MM is reset, the inventory data is refreshed in the MM database. This includes items like IBM VPD (e.g. - serial number, UUID) and MAC address information. Applications need to know when this information has been populated on the MM before they begin to query it using SNMP or other means. This simple flag object will return a ready or notReady indication when all blades and switches have completed initialization and the inventory information has been provided to the MM. Note that due to components that may be experiencing a 'communication failure' or 'initialization failure' condition, this object may continue to show notReady. Therefore, any application that polls this object should also incorporate a timeout A more granular, per-blade status is available via the bladeSystemStatusTable
| ||||
| TcomponentDriveTable | 1.3.6.1.4.1.2.3.51.2.2.23.10 | NA | mandatory | |
table · not-accessible · mandatory Table of information indicating presence of a disk drive on a component. The management module does not receive any inventory VPD from the component, so only the presence of a drive can be indicated by this table. | ||||
| RcomponentDriveEntry | 1.3.6.1.4.1.2.3.51.2.2.23.10.1 | NA | mandatory | |
| CcomponentDriveTopologyPath | 1.3.6.1.4.1.2.3.51.2.2.23.10.1.1 | OCTET STRING (SIZE (0..100)) | RO | mandatory |
column · OCTET STRING (SIZE (0..100)) · read-only · mandatory The unique identifier for a row in this table. The chassis and each installed component is represented by a hardware topology tree, where each node in the tree represents a component. The path to a particular component consists of one or more <component>,<instance> pairs, where each successive pair is a child of the previous parent pair. As an example, the root of the tree is the chassis and is represented by the pair 'CHASSIS, 1'. This pair indicates the first instance of the chassis. If a blade is inserted in slot 4 of the chassis, its topology path is 'CHASSIS, 1, BLADE, 4'. With this format, the components in the chassis can be determined along with their relative hierarchy to each other. This component table is indexed by this unique topology path and the numeric designations for the components are: CHASSIS, 0x01 Chassis MM, 0x02 Management Module BLADE, 0x03 Main system board of a blade POWER, 0x04 Power Supply, Power Module, etc COOLING, 0x05 Fan, blower, or other cooling device IO_MODULE, 0x06 Has I/O interface, i.e. - switch or bridge MEDIA, 0x07 Media device PROCESSOR, 0x08 Any processor, processor module, etc STORAGE, 0x09 Any type of storage device EXPANSION, 0x0A Expansion Card (not covered by more specific type) MEMORY, 0x0B Any memory device, module, etc MFRU, 0x0C Managed FRU Device PANEL, 0x0D Any sort of panel device, such as a front panel BLADE_EXPANSION_MODULE, 0x0E Expansion option (BEM) such as PEU, BSE, etc CARD_EXPANSION, 0x0F Expansion card, ie. daughter card CARD_HS_EXPANSION, 0x10 High Speed Expansion card, ie. daughter card INTERPOSER, 0x11 Interposer device CLOCK, 0x12 Clock card MUX, 0x13 Mulitplexer card ADDIN, 0x14 cKVM card & other addin cards STORAGE_MODULE, 0x15 Container of one or more Storage Devices SYS_EXPANSION_CARD, 0x16 Management card BATTERY, 0x17 A single battery BATTERY_MODULE, 0x18 Container of one or more batteries MEDIA_MODULE, 0x19 Container of one or more media devices MEMORY_BANK, 0x1A Memory banks AIR_FILTER, 0x1B Filter mechanism (bezel) SERIAL_PORT_MODULE, 0x1C Container of one or more serial ports PARENT, 0x1D Reference to parent for multi-parent support PHY_PORT, 0x1E Physical port IO_EXPANDER, 0x1F RAID card | ||||
| CcomponentDriveDescription | 1.3.6.1.4.1.2.3.51.2.2.23.10.1.2 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory A short text string describing the particular drive on the component. | ||||
| ScomponentDriveTableCacheTimeout | 1.3.6.1.4.1.2.3.51.2.2.23.11 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory The timeout value (in seconds) of the cached data for the table, componentDriveTable. This value is static (constant) and cannot be set. | ||||
| NlicenseKeyInfo | 1.3.6.1.4.1.2.3.51.2.2.30 | |||
| TlicenseKeyInfoTable | 1.3.6.1.4.1.2.3.51.2.2.30.1 | NA | mandatory | |
table · not-accessible · mandatory Table of license key information. | ||||
| RlicenseKeyInfoEntry | 1.3.6.1.4.1.2.3.51.2.2.30.1.1 | NA | mandatory | |
row · not-accessible · mandatory License key information entry. | ||||
| ClicenseKeyComponentIndex | 1.3.6.1.4.1.2.3.51.2.2.30.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory License key component table index.
| ||||
| ClicenseKeyIndex | 1.3.6.1.4.1.2.3.51.2.2.30.1.1.2 | INTEGER (1..255) | RO | mandatory |
column · INTEGER (1..255) · read-only · mandatory The license key index for the chassis component. | ||||
| ClicenseKeyDescription | 1.3.6.1.4.1.2.3.51.2.2.30.1.1.3 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The description for a license key. | ||||
| ClicenseKeyTimestamp | 1.3.6.1.4.1.2.3.51.2.2.30.1.1.4 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The date and time of this license key. | ||||
| ClicenseKeyLicenseID | 1.3.6.1.4.1.2.3.51.2.2.30.1.1.5 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The unique identifier for this license key. | ||||
| ClicenseKeyOtherInfo | 1.3.6.1.4.1.2.3.51.2.2.30.1.1.6 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Any other information related to this license key. | ||||
| ClicenseKeyStatus | 1.3.6.1.4.1.2.3.51.2.2.30.1.1.7 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current status of this license key.
| ||||
| TchassisLicenseKeyTable | 1.3.6.1.4.1.2.3.51.2.2.30.5 | NA | mandatory | |
table · not-accessible · mandatory Table of chassis license key information. | ||||
| RchassisLicenseKeyEntry | 1.3.6.1.4.1.2.3.51.2.2.30.5.1 | NA | mandatory | |
| CchassisLicenseKeyIndex | 1.3.6.1.4.1.2.3.51.2.2.30.5.1.1 | INTEGER (1..255) | RO | mandatory |
column · INTEGER (1..255) · read-only · mandatory The key index for the chassis license keys. | ||||
| CchassisLicenseKeyFeature | 1.3.6.1.4.1.2.3.51.2.2.30.5.1.2 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The name of the Feature for the license key. | ||||
| CchassisLicenseKeyFeatureType | 1.3.6.1.4.1.2.3.51.2.2.30.5.1.3 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The Feature Type Code for the license key. | ||||
| CchassisLicenseKeyDescription | 1.3.6.1.4.1.2.3.51.2.2.30.5.1.4 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The description of the license key. | ||||
| CchassisLicenseKeySystem | 1.3.6.1.4.1.2.3.51.2.2.30.5.1.5 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory System information for the license key. | ||||
| CchassisLicenseKeyLicenseID | 1.3.6.1.4.1.2.3.51.2.2.30.5.1.6 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Identification of the license key. | ||||
| CchassisLicenseKeyValidation | 1.3.6.1.4.1.2.3.51.2.2.30.5.1.7 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Validation of the license key. | ||||
| CchassisLicenseKeyStatus | 1.3.6.1.4.1.2.3.51.2.2.30.5.1.8 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current status of the license key.
| ||||
| CchassisLicenseKeyTimeLimit | 1.3.6.1.4.1.2.3.51.2.2.30.5.1.9 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Date and Time (GMT) when license expires. | ||||
| CchassisLicenseKeyUsageLimit | 1.3.6.1.4.1.2.3.51.2.2.30.5.1.10 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Number of times remaining for license usage. A negative value indicates that there is no Usage Limit for the license. | ||||
| NerrorLogs | 1.3.6.1.4.1.2.3.51.2.3 | |||
| NeventLog | 1.3.6.1.4.1.2.3.51.2.3.4 | |||
| TreadEventLogTable | 1.3.6.1.4.1.2.3.51.2.3.4.2 | NA | mandatory | |
table · not-accessible · mandatory Table of event log entry information. | ||||
| RreadEventLogEntry | 1.3.6.1.4.1.2.3.51.2.3.4.2.1 | NA | mandatory | |
| CreadEventLogIndex | 1.3.6.1.4.1.2.3.51.2.3.4.2.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The event log index number. | ||||
| CreadEventLogString | 1.3.6.1.4.1.2.3.51.2.3.4.2.1.2 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory A string of data detailing an event. | ||||
| SclearEventLog | 1.3.6.1.4.1.2.3.51.2.3.4.3 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Clear the event log. NOTE: Value returned for the GET command is meaningless for this MIB object.
| ||||
| SmonitorLogStateEvents | 1.3.6.1.4.1.2.3.51.2.3.4.4 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory If disabled, it means the info LED will not turn on when the log gets full and no alerts will be sent out. If enabled, the LED will turn on when the log gets full and alerts will be sent out.
| ||||
| TreadEnhancedEventLogTable | 1.3.6.1.4.1.2.3.51.2.3.4.6 | NA | mandatory | |
table · not-accessible · mandatory Table of enhanced event log entry information. | ||||
| RreadEnhancedEventLogEntry | 1.3.6.1.4.1.2.3.51.2.3.4.6.1 | NA | mandatory | |
row · not-accessible · mandatory Enhaced Event log table entry, new entries could be added for new items. | ||||
| CreadEnhancedEventLogNumber | 1.3.6.1.4.1.2.3.51.2.3.4.6.1.1 | Unsigned32 (0..4294967295) | RO | mandatory |
column · Unsigned32 (0..4294967295) · read-only · mandatory The event log number for the enhanced event log. | ||||
| CreadEnhancedEventLogAttribute | 1.3.6.1.4.1.2.3.51.2.3.4.6.1.2 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory A string of data detailing an event log's attribute, such as the Event ID and Call Home Flag. The Event ID is a hexadecimal number representing an specific or class of events. The call home flag indicates that the corresponding problem may result in a call home. | ||||
| CreadEnhancedEventLogMessage | 1.3.6.1.4.1.2.3.51.2.3.4.6.1.3 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory A string of data detailing an event log message. | ||||
| CreadEnhancedEventLogSequenceNum | 1.3.6.1.4.1.2.3.51.2.3.4.6.1.4 | Unsigned32 (0..4294967295) | RO | mandatory |
column · Unsigned32 (0..4294967295) · read-only · mandatory The sequence number for the enhanced event log. This number is the next sequence number when this event record was create. This number continues to grow, even if this event log is cleared, until it reaches the maximum value of 4294967295. The next sequence number following the maximum value is 1. | ||||
| TreadAuditLogTable | 1.3.6.1.4.1.2.3.51.2.3.4.10 | NA | mandatory | |
table · not-accessible · mandatory Table of audit log entry information. Audit log includes the logs whose source is 'Audit' | ||||
| RreadAuditLogEntry | 1.3.6.1.4.1.2.3.51.2.3.4.10.1 | NA | mandatory | |
row · not-accessible · mandatory Audit log table entry, new entries could be added for new items.
| ||||
| CreadAuditLogNumber | 1.3.6.1.4.1.2.3.51.2.3.4.10.1.1 | Unsigned32 (0..4294967295) | RO | mandatory |
column · Unsigned32 (0..4294967295) · read-only · mandatory The audit log number. | ||||
| CreadAuditLogAttribute | 1.3.6.1.4.1.2.3.51.2.3.4.10.1.2 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory A string of data detailing an audit eventlog's attribute. | ||||
| CreadAuditLogMessage | 1.3.6.1.4.1.2.3.51.2.3.4.10.1.3 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory A string of data detailing an audit event log message. | ||||
| CreadAuditLogSequenceNum | 1.3.6.1.4.1.2.3.51.2.3.4.10.1.4 | Unsigned32 (0..4294967295) | RO | mandatory |
column · Unsigned32 (0..4294967295) · read-only · mandatory The sequence number for the audit event log. This number is the next sequence number when this event record was create. This number continues to grow, even if this event log is cleared, until it reaches the maximum value of 4294967295. The next sequence number following the maximum value is 1. | ||||
| SclearAuditLog | 1.3.6.1.4.1.2.3.51.2.3.4.11 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Clear the audit log. NOTE: Value returned for the GET command is meaningless for this MIB object.
| ||||
| TreadSystemLogTable | 1.3.6.1.4.1.2.3.51.2.3.4.12 | NA | mandatory | |
table · not-accessible · mandatory Table of system log entry information. System log includes the logs whose source is other than 'Audit' | ||||
| RreadSystemLogEntry | 1.3.6.1.4.1.2.3.51.2.3.4.12.1 | NA | mandatory | |
row · not-accessible · mandatory System log table entry, new entries could be added for new items.
| ||||
| CreadSystemLogNumber | 1.3.6.1.4.1.2.3.51.2.3.4.12.1.1 | Unsigned32 (0..4294967295) | RO | mandatory |
column · Unsigned32 (0..4294967295) · read-only · mandatory The system log index number. | ||||
| CreadSystemLogAttribute | 1.3.6.1.4.1.2.3.51.2.3.4.12.1.2 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory A string of data detailing an system event log's attribute. | ||||
| CreadSystemLogMessage | 1.3.6.1.4.1.2.3.51.2.3.4.12.1.3 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory A string of data detailing an system event log message. | ||||
| CreadSystemLogSequenceNum | 1.3.6.1.4.1.2.3.51.2.3.4.12.1.4 | Unsigned32 (0..4294967295) | RO | mandatory |
column · Unsigned32 (0..4294967295) · read-only · mandatory The sequence number for the system event log. This number is the next sequence number when this event record was create. This number continues to grow, even if this event log is cleared, until it reaches the maximum value of 4294967295. The next sequence number following the maximum value is 1. | ||||
| SclearSystemLog | 1.3.6.1.4.1.2.3.51.2.3.4.13 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Clear the system log. NOTE: Value returned for the GET command is meaningless for this MIB object.
| ||||
| TreadEventLogAuxTable | 1.3.6.1.4.1.2.3.51.2.3.4.14 | NA | mandatory | |
table · not-accessible · mandatory Table of system log entry auxiliary information. | ||||
| RreadEventLogAuxEntry | 1.3.6.1.4.1.2.3.51.2.3.4.14.1 | NA | mandatory | |
row · not-accessible · mandatory Event log auxiliary table entry, new entries could be added for new items. | ||||
| CreadEventLogAuxNumber | 1.3.6.1.4.1.2.3.51.2.3.4.14.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The system log auxiliary index number. To relate this information to the system log, match Sequence number of this entry to the Sequence number of the system log entry. | ||||
| CreadEventLogAuxSequenceNum | 1.3.6.1.4.1.2.3.51.2.3.4.14.1.2 | Unsigned32 (0..4294967295) | RO | mandatory |
column · Unsigned32 (0..4294967295) · read-only · mandatory The sequence number for the system event log that contains this Auxiliary information. Value is from 1 through 4294967295 and then wraps. | ||||
| CreadEventLogAuxMessage | 1.3.6.1.4.1.2.3.51.2.3.4.14.1.3 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory A string of data detailing the auxiliary information from the log event. | ||||
| NconfigureSP | 1.3.6.1.4.1.2.3.51.2.4 | |||
| NremoteAccessConfig | 1.3.6.1.4.1.2.3.51.2.4.1 | |||
| NgeneralRemoteCfg | 1.3.6.1.4.1.2.3.51.2.4.1.1 | |||
| SremoteAlertRetryDelay | 1.3.6.1.4.1.2.3.51.2.4.1.1.3 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Number in seconds to delay between retries if sending a remote alert is unsuccessful.
| ||||
| SremoteAlertRetryCount | 1.3.6.1.4.1.2.3.51.2.4.1.1.4 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Number of additional times a remote alert will be retried if not successfully sent. A value of zero indicates no retries will be attempted.
| ||||
| SuserAuthenticationMethod | 1.3.6.1.4.1.2.3.51.2.4.1.1.7 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Use this field to specify how users attempting to login should be authenticated.
There are two methods:
Local authentication. Userid and password are verified by searching the list
of users locally configured under Local Login Profiles.
LDAP based authentication. Users are authenticated via a remote LDAP server.
One or both authentication methods can be selected. If both methods should be
used, the order must be specified.
| ||||
| SmaxSessionsPerLDAPUser | 1.3.6.1.4.1.2.3.51.2.4.1.1.9 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory The maximum number of simultaneous active sessions allowed for each LDAP user. If the value is 0, this option is disabled. The minimum value is 1 and the maximum value is 20. | ||||
| SauthenticationLoggingTimeout | 1.3.6.1.4.1.2.3.51.2.4.1.1.10 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Use this option to set how long, in seconds, MM will not log the authentication events for the same user. The default setting is 5 minutes. 0 indicates log all authentication events, 255 indicates don't log any new authentication events.
| ||||
| StrackingIP | 1.3.6.1.4.1.2.3.51.2.4.1.1.11 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory This option indicates tracking different IP addresses for the same user is enabled or not. If it is enabled then an access every second from alternating IP addresses will result in multiple log entries, regardless of the time duration set in the 'authenticaionLoggingTimeout'field. If this flag is disabled, multiple accesses by varying IP addresses will only be logged as 'new' accesses if they are out of the 'authenticationLoggingTimeout'.
| ||||
| NaccountSecurityManagement | 1.3.6.1.4.1.2.3.51.2.4.1.1.20 | |||
| SaccountSecurityLevel | 1.3.6.1.4.1.2.3.51.2.4.1.1.20.1 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory The level of security needed for local user login passwords.
The legacy level:
- no password required
- no password expiration
- no password re-use restrictions
- no frequency of password change restrictions
- account is locked for 2 minutes after 5 login failures
- simple password rules
- no account inactivity monitoring
The high level:
- password required
- factory default 'USERID' account password must be changed on next login
- force user to change password on first login
- password expires in 90 days
- password re-use checking enabled (last 5 passwords kept in history)
- minimum 24 hours interval between password changes
- account is locked for 60 minutes after 5 login failures
- complex password rules with 2 degrees of difference from previous password
- alert on account inactivity after 120 days
- accounts disabled after 180 days of inactivity
The custom level:
- set the password settings individually under customSecuritySettings
The default value is legacy.
| ||||
| NcustomSecuritySettings | 1.3.6.1.4.1.2.3.51.2.4.1.1.20.2 | |||
| SpasswordExpirationPeriod | 1.3.6.1.4.1.2.3.51.2.4.1.1.20.2.2 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory The number of days before login passwords expire. The minimum value is 1 day and the maximum value is 365 days. The default value is 90 days. A value of 0 disables this option. | ||||
| SdefaultAdminPasswordExpired | 1.3.6.1.4.1.2.3.51.2.4.1.1.20.2.3 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory If enabled, the factory default 'USERID' account password must be changed on next login. The default value is disabled.
| ||||
| SminimumPasswordReuseCycle | 1.3.6.1.4.1.2.3.51.2.4.1.1.20.2.4 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory The number of unique passwords a user must choose before reusing a password. The default value is none.
| ||||
| ScomplexPasswordRules | 1.3.6.1.4.1.2.3.51.2.4.1.1.20.2.5 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory If enabled, the minimum complexity rules will be enforced for all
local login passwords and 'User login password required' rule will be enabled.
The complex rules are as follows:
must be 8-31 characters
must contain at least one number
must contain at least one letter
cannot contain white space characters
cannot be a repeat or reverse of user name
no more than 3 of the same characters used consecutively
must contain at least 2 of the following combinations:
at least one upper case letter
at least one lower case letter
at least one special character
Password and password confirm values must match
If disabled, the lagacy rules are:
must be 5-31 characters
must contain at least one number
must contain at least one letter
cannot contain white space characters
Password and password confirm values must match
The default value is disabled.
| ||||
| SminimumDiffCharsPassword | 1.3.6.1.4.1.2.3.51.2.4.1.1.20.2.6 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory The required minimum number of characters in the new password different from the previous password. The default value is 2. A SET of this object is ignored until the complexPasswordRules option is enabled and the minimumPasswordReuseCycle is not none(0)
| ||||
| SchangePasswordFirstAccess | 1.3.6.1.4.1.2.3.51.2.4.1.1.20.2.7 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory If enabled, the login user will be forced to change their password on the first access after the account has been established or on the first access after an administrator has changed the password for the user, except for the administrator password for USERID. The default value is disabled.
| ||||
| SinactivityAlertPeriod | 1.3.6.1.4.1.2.3.51.2.4.1.1.20.2.8 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory The period of time in days before generating an alert for a dormant account. This value applies to all login accounts, including the administrator account. The minimum value is 1 day and the maximum value is 365 days. The default value is 0 which disables this option. NOTE: This value must be less than the inactivityAlertDisablePeriod. | ||||
| SinactivityAlertDisablePeriod | 1.3.6.1.4.1.2.3.51.2.4.1.1.20.2.9 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory The period of time in days before generating an alert and disabling a dormant account. This value applies to all login accounts, excluding the administrator account. The minimum value is 1 day and the maximum value is 365 days. The default value is 0 which disables this option. NOTE: This value must be greater than the inactivityAlertPeriod. | ||||
| SlockoutPeriod | 1.3.6.1.4.1.2.3.51.2.4.1.1.20.2.10 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory The period of time in minutes that a user is locked out after the maximum number of login failures was reached. The minimum value is is 1 minute and the maximum value is 2880 minutes. The default value is 2 minutes for the Legacy security level and 60 minutes for the High security level. A value of 0 disables this option. | ||||
| SmaxLoginFailures | 1.3.6.1.4.1.2.3.51.2.4.1.1.20.2.11 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory The maximum number of login failures before a user account is locked. A value of 0 disables this option. The default value is 5.
| ||||
| SpasswordChangeInterval | 1.3.6.1.4.1.2.3.51.2.4.1.1.20.2.12 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory A minimum period of time that user is not able to change their own password. The range of acceptable values will be from 0 to 1440 (or 60 days). A value of 0 disables this option. If the password expiration period is set, it must be greater than the minimum password change interval. | ||||
| NserialPortCfg | 1.3.6.1.4.1.2.3.51.2.4.1.2 | |||
| SportBaud | 1.3.6.1.4.1.2.3.51.2.4.1.2.1 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Baud rate for the serial port.
| ||||
| SportParity | 1.3.6.1.4.1.2.3.51.2.4.1.2.2 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Parity setting for the serial port.
| ||||
| SportStopBits | 1.3.6.1.4.1.2.3.51.2.4.1.2.3 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Number of stop bits for the serial port.
| ||||
| NremoteAlertIds | 1.3.6.1.4.1.2.3.51.2.4.1.3 | |||
| TremoteAlertIdsTable | 1.3.6.1.4.1.2.3.51.2.4.1.3.1 | NA | mandatory | |
table · not-accessible · mandatory Table of remote alert entries. This table lets you configure remote alert recipients. You can define up to 12 unique recipients. NOTE: All selected alert events will be sent to all enabled alert recipients. | ||||
| RremoteAlertIdsEntry | 1.3.6.1.4.1.2.3.51.2.4.1.3.1.1 | NA | mandatory | |
| CremoteAlertIdEntryIndex | 1.3.6.1.4.1.2.3.51.2.4.1.3.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Index for remote alert entry. | ||||
| CremoteAlertIdEntryStatus | 1.3.6.1.4.1.2.3.51.2.4.1.3.1.1.2 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Remote alert entry status, invalid means entry not defined yet, disabledAndValid means entry defined but not enabled to send an alert, enabledAndValid means entry defined and enabled to send an alert.
| ||||
| CremoteAlertIdEntryIpOrHostAddress | 1.3.6.1.4.1.2.3.51.2.4.1.3.1.1.3 | OCTET STRING (SIZE (0..50)) | RW | mandatory |
column · OCTET STRING (SIZE (0..50)) · read-write · mandatory A null terminated string that either contains an IP address of the form '1.2.3.4' or a host name (if DNS is enabled) for the alert entry. | ||||
| CremoteAlertIdEntryTextDescription | 1.3.6.1.4.1.2.3.51.2.4.1.3.1.1.4 | OCTET STRING (SIZE (0..50)) | RW | mandatory |
column · OCTET STRING (SIZE (0..50)) · read-write · mandatory A null terminated string that contains a text description of this entry. | ||||
| CremoteAlertIdEntryNotificationType | 1.3.6.1.4.1.2.3.51.2.4.1.3.1.1.5 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Remote alert entry notification method. Types include unknown when the type can't be determined (read-only), snmpOverLan for an SNMP alert over ethernet, and emailOverLan for a E-Mail alert over ethernet.
| ||||
| CremoteAlertIdEmailAddr | 1.3.6.1.4.1.2.3.51.2.4.1.3.1.1.9 | OCTET STRING (SIZE (0..64)) | RW | mandatory |
column · OCTET STRING (SIZE (0..64)) · read-write · mandatory A null terminated string that contains an E-Mail Address. For example, '[email protected]'. Used only for an E-mail over LAN notification type. | ||||
| CremoteAlertIdEntrySelectiveAlert | 1.3.6.1.4.1.2.3.51.2.4.1.3.1.1.13 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Remote alert entry selective alert setting. A value of critOnlyAlerts will only send critical alerts to this remote alert recipient, a value of allAlerts will send all alerts to this remote alert recipient.
| ||||
| SgenerateTestAlert | 1.3.6.1.4.1.2.3.51.2.4.1.3.30 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Generate a Test Alert. This will send a test alert to all configured and enabled remote alert recipients. NOTE: Value returned for the GET command is meaningless for this MIB object.
| ||||
| NremoteAccessIds | 1.3.6.1.4.1.2.3.51.2.4.1.4 | |||
| TremoteAccessIdsTable | 1.3.6.1.4.1.2.3.51.2.4.1.4.1 | NA | mandatory | |
table · not-accessible · mandatory Table of remote access profiles. This table lets you to configure all login profiles. NOTE: By default, the management module comes configured with one login profile that allows remote access using a login ID of 'USERID' and a password of 'PASSW0RD' (the 0 is a zero). To avoid a potential security exposure, we strongly recommend that you change this default Login Profile to values of your choice. | ||||
| RremoteAccessIdsEntry | 1.3.6.1.4.1.2.3.51.2.4.1.4.1.1 | NA | mandatory | |
| CremoteAccessIdEntryIndex | 1.3.6.1.4.1.2.3.51.2.4.1.4.1.1.1 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Index for Remote access entry. | ||||
| CremoteAccessIdEntryUserId | 1.3.6.1.4.1.2.3.51.2.4.1.4.1.1.2 | OCTET STRING (SIZE (0..33)) | RW | mandatory |
column · OCTET STRING (SIZE (0..33)) · read-write · mandatory Remote access entry null terminated string that contains the userid. It must not be a duplicate of any previously configured ones. This field is only allowed to be set when the entry status is under creation. | ||||
| CremoteAccessIdEntryPassword | 1.3.6.1.4.1.2.3.51.2.4.1.4.1.1.3 | OCTET STRING (SIZE (0..17)) | RW | mandatory |
column · OCTET STRING (SIZE (0..17)) · read-write · mandatory Remote access password. The password rules are dictated by a combination of the chassis security policy setting (securityPolicySetting) and the user account security level setting (accountSecurityLevel). Refer to object complexPasswordRules to understand the requirements. NOTE: Value returned by the GET command is meaningless for this MIB object. | ||||
| CremoteAccessIdEntryPermgroups | 1.3.6.1.4.1.2.3.51.2.4.1.4.1.1.10 | OCTET STRING | RW | mandatory |
column · OCTET STRING · read-write · mandatory A list of permission groups for this userid, delmited with a '|' | ||||
| CremoteAccessIdEntryLoggedIn | 1.3.6.1.4.1.2.3.51.2.4.1.4.1.1.11 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates if user is currently logged in or not.
| ||||
| CremoteAccessIdEntryLastLogin | 1.3.6.1.4.1.2.3.51.2.4.1.4.1.1.12 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Timestamp for the last successful login by the user. | ||||
| CremoteAccessIdEntryPwdCompliant | 1.3.6.1.4.1.2.3.51.2.4.1.4.1.1.13 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates if user complies with all of the password rules currently in effect.
| ||||
| CremoteAccessIdEntryPwdExp | 1.3.6.1.4.1.2.3.51.2.4.1.4.1.1.14 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The number of days until the user's current password expires. | ||||
| CremoteAccessIdEntryDormant | 1.3.6.1.4.1.2.3.51.2.4.1.4.1.1.15 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates if the user account has been inactive for a specified amount of time based on inactivityAlertDisablePeriod in the customSecuritySettings section.
| ||||
| CremoteAccessIdEntryState | 1.3.6.1.4.1.2.3.51.2.4.1.4.1.1.16 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates the state of the user:
Active - normal state
Disabled - user cannot use account until enabled by a
supervisor or chassis user account manager. An account
can get disabled after being dormant for a specified
amount of time OR as a result of a supervisor or chassis
user account manager disabling it.
Locked - account is temporarily locked due to repeated
unsuccessful login attempts as specified by lockoutPeriod
in the customSecuritySettings section. Account can be
unlocked by a supervisor or chassis user account manager
OR can be automatically unlocked after the lockoutPeriod expires.
NOTE: The disable action does not apply to supervisor or chassis
user account manager accounts.
| ||||
| CremoteAccessIdEntryAction | 1.3.6.1.4.1.2.3.51.2.4.1.4.1.1.17 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Actions that only a supervisor or chassis user account manager
can perform for each user id:
Enable - enables an account in the Disabled state
Disable - disables an account in the Active or Locked state
Unlock - unlock an account in the Locked state
NOTE: The disable action does not apply to supervisor or chassis
user account manager accounts.
NOTE: Value returned for the GET command is meaningless for this
MIB object.
| ||||
| CremoteAccessIdEntrySessionCount | 1.3.6.1.4.1.2.3.51.2.4.1.4.1.1.18 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The number of sessions the user is currently logged in to. | ||||
| CremoteAccessIdEntryMaxSessions | 1.3.6.1.4.1.2.3.51.2.4.1.4.1.1.19 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory The maximum number of simultaneous active sessions allowed for the user. If the value is 0, this option is disabled. The minimum value is 1 and the maximum value is 20. | ||||
| CremoteAccessIdEntryStatus | 1.3.6.1.4.1.2.3.51.2.4.1.4.1.1.20 | EntryStatus | RW | mandatory |
column · EntryStatus · read-write · mandatory This object manages the creation and deletion of this entry.
The steps recommended to add a new group are:
1. Create a new entry in this table
remoteAccessIdEntryStatus = createRequest
2. Set remoteAccessId as required.
The remoteAccessIdUserId and the remoteAccessIdPassword must be set
before the entry becomes valid. To set the remoteAccessIdsEntryPermgroups or
remoteAccessIdsEntryMaxSessions before the entry is valid, set these fields before
both the password and userId are set.
Only one row will be allowed to be underCreation at one time, and it must have the next index
in the table.
valid(1) - Indicates that the group represented
by this entry is available for use.
createRequest(2) - A new entry will be created in this table
for the specified group and the new entry
will transition to the underCreation(3).
underCreation(3) - Indicates that this entry exists in the
agent but is unavailable for use. After completing the
create operation, the agent will set this object to
underCreation(3).
invalid(4) - Deletes this entry. | ||||
| CremoteAccessIdEntryIPMIProvisioned | 1.3.6.1.4.1.2.3.51.2.4.1.4.1.1.21 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Indicates if the user has been provisioned as an IPMI account. If this is user is provisioned as an IPMI account, the nodes (scope) and authorities will be determined by the scope and authorities of the permission groups to which this user belongs. These can be seen in the remoteAccessRBSscopeTable and remoteAccessRBSroleTable for the permission groups to which this user is assigned. If the userid is longer than 16 characters or there are more than 12 user accounts enabled for IPMI provisioning, setting the value to yes will return an error. When provisioning an IPMI account by setting this object to yes(1), the SNMPv3 account is also automatically provisioned.
| ||||
| CremoteAccessIdEntrySNMPv3Provisioned | 1.3.6.1.4.1.2.3.51.2.4.1.4.1.1.22 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Indicates if the user has been provisioned as an SNMPv3 account. If this is user is provisioned as an SNMPv3 account, the nodes (scope) and authorities will be determined by the scope and authorities of the permission groups to which this user belongs. These can be seen in the remoteAccessRBSscopeTable and remoteAccessRBSroleTable for the permission groups to which this user is assigned. If the userid is longer than 16 characters or there are more than 12 user accounts enabled for SNMPv3 provisioning, setting the value to yes will return an error. When provisioning a SNMPv3 account by setting this object to yes(1), the IPMI account is also automatically provisioned.
| ||||
| TremoteAccessRBSroleTable | 1.3.6.1.4.1.2.3.51.2.4.1.4.3 | NA | mandatory | |
table · not-accessible · mandatory Table of RBS User Role profiles. | ||||
| RremoteAccessRBSroleEntry | 1.3.6.1.4.1.2.3.51.2.4.1.4.3.1 | NA | mandatory | |
| CroleIndex | 1.3.6.1.4.1.2.3.51.2.4.1.4.3.1.1 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Index for RBS User Role entry. | ||||
| CroleId | 1.3.6.1.4.1.2.3.51.2.4.1.4.3.1.2 | OCTET STRING (SIZE (0..63)) | RW | mandatory |
column · OCTET STRING (SIZE (0..63)) · read-write · mandatory Remote access RBS role entry null terminated string that contains the permission group ID. It must not be a duplicate of any previously configured ones. This field is only allowed to be set when the entry status is under creation. | ||||
| CrbsSupervisor | 1.3.6.1.4.1.2.3.51.2.4.1.4.3.1.3 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory User has no restrictions.
| ||||
| CrbsOperator | 1.3.6.1.4.1.2.3.51.2.4.1.4.3.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory User has read-only access, and cannot perform any save, modify, clear, or state affecting operations (e.g. restart MM, restore defaults, upgrade the firmware, etc.).
| ||||
| CrbsChassisOperator | 1.3.6.1.4.1.2.3.51.2.4.1.4.3.1.5 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory User has ability to browse status and properties of chassis components (MM, chassis fans, midplane, power modules). Ability to backup MM configuration to a file. Saving MM configuration to chassis requires supervisor access.
| ||||
| CrbsChassisAccountManagement | 1.3.6.1.4.1.2.3.51.2.4.1.4.3.1.6 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory User can add/modify/delete user login profiles. Ability to backup MM configuration to a file. Changing global login settings require chassis configuration authority.
| ||||
| CrbsChassisLogManagement | 1.3.6.1.4.1.2.3.51.2.4.1.4.3.1.7 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory User has ability to clear the MM event log, change log policy settings, and backup MM configuration to a file.
| ||||
| CrbsChassisConfiguration | 1.3.6.1.4.1.2.3.51.2.4.1.4.3.1.8 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory User can modify and save any chassis configuration parameter (except user profiles and event log settings). Ability to restore MM factory defaults if the user also has chassis administration permissions. Ability to change the global login settings, SOL configuration, and backup MM configuration to a file.
| ||||
| CrbsChassisAdministration | 1.3.6.1.4.1.2.3.51.2.4.1.4.3.1.9 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory User has ability to do MM firmware updates, modify chassis LEDs, restore MM factory defaults if the user also has chassis configuration permissions. Ability to restart MM and backup MM configuration to a file.
| ||||
| CrbsBladeOperator | 1.3.6.1.4.1.2.3.51.2.4.1.4.3.1.10 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory User has ability to browse status and properties of blades.
| ||||
| CrbsBladeRemotePresence | 1.3.6.1.4.1.2.3.51.2.4.1.4.3.1.11 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory User has ability to access the blades remote console. The ability to issue the CLI console command to start an SOL session to a blade will also require this authority.
| ||||
| CrbsBladeConfiguration | 1.3.6.1.4.1.2.3.51.2.4.1.4.3.1.12 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory User can modify and save any blade configuration parameter.
| ||||
| CrbsBladeAdministration | 1.3.6.1.4.1.2.3.51.2.4.1.4.3.1.13 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory User can power on/off and restart blades, activate standby blades, do firmware updates, and modify blade LEDs.
| ||||
| CrbsSwitchModuleOperator | 1.3.6.1.4.1.2.3.51.2.4.1.4.3.1.14 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory User has ability to browse status and properties of I/O Modules, and to ping I/O Modules.
| ||||
| CrbsSwitchModuleConfiguration | 1.3.6.1.4.1.2.3.51.2.4.1.4.3.1.15 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory User can modify the I/O Module IP address, configure I/O Module Advanced Management parameters, and restore factory defaults on an I/O Module. Note that a user requires both I/O Module configuration and I/O Module administration roles in order to be able to launch a telnet or web UI session to an I/O Module, or to restore factory defaults on an I/O Module.
| ||||
| CrbsSwitchModuleAdministration | 1.3.6.1.4.1.2.3.51.2.4.1.4.3.1.16 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory User can power on/off and restart the I/O Modules, update I/O Module firmware, enable/disable the Fast POST and External Ports of an I/O Module. Note that a user requires both I/O Module configuration and I/O Module administration roles in order to be able to launch a telnet session to an I/O Module, or to restore factory defaults on an I/O Module.
| ||||
| CrbsEntryStatus | 1.3.6.1.4.1.2.3.51.2.4.1.4.3.1.23 | EntryStatus | RW | mandatory |
column · EntryStatus · read-write · mandatory This object manages the creation and deletion of this entry.
The steps recommended to add a new group are:
1. Create a new entry in this table
rbsEntryStatus = createRequest
2. Set roleId as required.
Only one row will be allowed to be underCreation at one time, and it must have the next index
in the table.
valid(1) - Indicates that the group represented
by this entry is available for use.
createRequest(2) - A new entry will be created in this table
for the specified group and the new entry
will transition to the underCreation(3).
underCreation(3) - Indicates that this entry exists in the
agent but is unavailable for use. After completing the
create operation, the agent will set this object to
underCreation(3).
invalid(4) - Deletes this entry. | ||||
| TremoteAccessRBSscopeTable | 1.3.6.1.4.1.2.3.51.2.4.1.4.4 | NA | mandatory | |
table · not-accessible · mandatory Table of RBS User Scope profiles. | ||||
| RremoteAccessRBSscopeEntry | 1.3.6.1.4.1.2.3.51.2.4.1.4.4.1 | NA | mandatory | |
| CscopeIndex | 1.3.6.1.4.1.2.3.51.2.4.1.4.4.1.1 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Index for RBS User Scope Entry. | ||||
| CscopeId | 1.3.6.1.4.1.2.3.51.2.4.1.4.4.1.2 | OCTET STRING (SIZE (0..63)) | RO | mandatory |
column · OCTET STRING (SIZE (0..63)) · read-only · mandatory Remote access RBS scope entry null terminated string that contains the permission group ID. | ||||
| CrbsChassis | 1.3.6.1.4.1.2.3.51.2.4.1.4.4.1.3 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory User has access to the MM and chassis functions.
| ||||
| CrbsBlade1 | 1.3.6.1.4.1.2.3.51.2.4.1.4.4.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory User has access to the blade in slot 1.
| ||||
| CrbsBlade2 | 1.3.6.1.4.1.2.3.51.2.4.1.4.4.1.5 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory User has access to the blade in slot 2.
| ||||
| CrbsBlade3 | 1.3.6.1.4.1.2.3.51.2.4.1.4.4.1.6 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory User has access to the blade in slot 3.
| ||||
| CrbsBlade4 | 1.3.6.1.4.1.2.3.51.2.4.1.4.4.1.7 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory User has access to the blade in slot 4.
| ||||
| CrbsBlade5 | 1.3.6.1.4.1.2.3.51.2.4.1.4.4.1.8 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory User has access to the blade in slot 5.
| ||||
| CrbsBlade6 | 1.3.6.1.4.1.2.3.51.2.4.1.4.4.1.9 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory User has access to the blade in slot 6.
| ||||
| CrbsBlade7 | 1.3.6.1.4.1.2.3.51.2.4.1.4.4.1.10 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory User has access to the blade in slot 7.
| ||||
| CrbsBlade8 | 1.3.6.1.4.1.2.3.51.2.4.1.4.4.1.11 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory User has access to the blade in slot 8.
| ||||
| CrbsBlade9 | 1.3.6.1.4.1.2.3.51.2.4.1.4.4.1.12 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory User has access to the blade in slot 9.
| ||||
| CrbsBlade10 | 1.3.6.1.4.1.2.3.51.2.4.1.4.4.1.13 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory User has access to the blade in slot 10.
| ||||
| CrbsBlade11 | 1.3.6.1.4.1.2.3.51.2.4.1.4.4.1.14 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory User has access to the blade in slot 11.
| ||||
| CrbsBlade12 | 1.3.6.1.4.1.2.3.51.2.4.1.4.4.1.15 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory User has access to the blade in slot 12.
| ||||
| CrbsBlade13 | 1.3.6.1.4.1.2.3.51.2.4.1.4.4.1.16 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory User has access to the blade in slot 13.
| ||||
| CrbsBlade14 | 1.3.6.1.4.1.2.3.51.2.4.1.4.4.1.17 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory User has access to the blade in slot 14.
| ||||
| CrbsSwitch1 | 1.3.6.1.4.1.2.3.51.2.4.1.4.4.1.18 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory User has access to I/O module 1.
| ||||
| CrbsSwitch2 | 1.3.6.1.4.1.2.3.51.2.4.1.4.4.1.19 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory User has access to I/O module 2.
| ||||
| CrbsSwitch3 | 1.3.6.1.4.1.2.3.51.2.4.1.4.4.1.20 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory User has access to I/O module 3.
| ||||
| CrbsSwitch4 | 1.3.6.1.4.1.2.3.51.2.4.1.4.4.1.21 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory User has access to I/O module 4.
| ||||
| CrbsSwitch5 | 1.3.6.1.4.1.2.3.51.2.4.1.4.4.1.22 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory User has access to I/O module 5.
| ||||
| CrbsSwitch6 | 1.3.6.1.4.1.2.3.51.2.4.1.4.4.1.23 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory User has access to I/O module 6.
| ||||
| CrbsSwitch7 | 1.3.6.1.4.1.2.3.51.2.4.1.4.4.1.24 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory User has access to I/O module 7.
| ||||
| CrbsSwitch8 | 1.3.6.1.4.1.2.3.51.2.4.1.4.4.1.25 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory User has access to I/O module 8.
| ||||
| CrbsSwitch9 | 1.3.6.1.4.1.2.3.51.2.4.1.4.4.1.26 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory User has access to I/O module 9.
| ||||
| CrbsSwitch10 | 1.3.6.1.4.1.2.3.51.2.4.1.4.4.1.27 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory User has access to I/O module 10.
| ||||
| ScmmCentralManagerIPMISNMPv3 | 1.3.6.1.4.1.2.3.51.2.4.1.4.9 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Indicates whether CMM is the central manager of the IPMI and SNMPv3 accounts. For a write, it can only be set to enabled. Once the CMM state is enabled, it can only be cleared by doing a reset to defaults. WARNING: Enabling CMM IPMI/SNMPv3 user account management will cause all presently existing IPMI/SNMPv3 user accounts on nodes to be overwritten. Please be sure to save any existing node IPMI/SNMPv3 account information before proceeding.
| ||||
| NuserInterfaces | 1.3.6.1.4.1.2.3.51.2.4.1.5 | |||
| Scli | 1.3.6.1.4.1.2.3.51.2.4.1.5.1 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Enable/Disable CLI access to the MM (telnet and SSH). The value enabled(3) means both telnet and ssh are enabled.
| ||||
| Ssnmp | 1.3.6.1.4.1.2.3.51.2.4.1.5.2 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Enable/Disable SNMP v1 and v3 access to the MM. The value enabled(3) means both telnet and ssh are enabled.
| ||||
| Stcm | 1.3.6.1.4.1.2.3.51.2.4.1.5.3 | INTEGER (0..20) | RW | mandatory |
scalar · INTEGER (0..20) · read-write · mandatory Enable/Disable TCP command mode (TCM) access to the MM. A value of 0 means disabled, any value from 1 to 20 means enabled. NOTE: MM will provide a max of 20 connections for both Secure TCP Command Mode and TCP Command Mode. | ||||
| Sweb | 1.3.6.1.4.1.2.3.51.2.4.1.5.4 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Enable/Disable Web access (HTTP/HTTPS) to the MM.
NOTE: Disabling web access to the MM will cause all
currently active web sessions to disconnect,
and you will no longer be able to access the
MM management functions using a web browser.
| ||||
| Sstcm | 1.3.6.1.4.1.2.3.51.2.4.1.5.5 | INTEGER (0..20) | RW | mandatory |
scalar · INTEGER (0..20) · read-write · mandatory Enable/Disable secure TCP command mode (STCM) access to the MM.
A value of 0 means disabled, any value from 1 to 20 means enabled.
NOTE: MM will provide a max of 20 connections for both
Secure TCP Command Mode and TCP Command Mode.
If no valid server certificate is in place,
Secure TCP Command Mode will not be allowed to set to enable. | ||||
| NmmSshClientAuth | 1.3.6.1.4.1.2.3.51.2.4.1.6 | |||
| TmmSshClientAuthPubKeyTable | 1.3.6.1.4.1.2.3.51.2.4.1.6.1 | NA | mandatory | |
table · not-accessible · mandatory A table that contains client authentication public key information. | ||||
| RmmSshClientAuthPubKeyEntry | 1.3.6.1.4.1.2.3.51.2.4.1.6.1.1 | NA | mandatory | |
row · not-accessible · mandatory A information list about a particular SSH public key used for client authentication. The primary table index is the same value as the associated remoteAccessIdEntryIndex. The secondary table index allows selection of the Nth public key for that remoteAccessIdEntryIndex. | ||||
| CmmSshClientAuthRemoteAccessIdIndex | 1.3.6.1.4.1.2.3.51.2.4.1.6.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The primary table index is the same value as the associated remoteAccessIdEntryIndex used as an index into the remoteAccessIdsTable. | ||||
| CmmSshClientAuthPubKeyIndex | 1.3.6.1.4.1.2.3.51.2.4.1.6.1.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The secondary table index used to select one of the client authentication public keys for a particular remote access Id. The index is an integer value from 1 to N where N is the number of keys associated with a particular remote access Id. An addition always causes the value of N to increase by one, effectively adding an entry after the existing keys for that remote access Id. If an entry is deleted from the table by setting mmSshClientAuthPubKeyEntryStatus = invalid, the key associated with that entry is deleted. If the deleted key was not the last key for a remote access Id (mmSshClientAuthPubKeyIndex is not the 'last' or Nth entry), the subsequent entries are renumbered after the deletion. A deletion always causes the value of N to decrease by one. The underlying SSH server implementation searches the keys in order from 1 to N when attempting public key authentication. NOTE:A maximum of 4 public keys can be installed for one remote access Id. | ||||
| CmmSshClientAuthPubKeyType | 1.3.6.1.4.1.2.3.51.2.4.1.6.1.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The type of the SSH public key represented by this entry.
| ||||
| CmmSshClientAuthPubKeySize | 1.3.6.1.4.1.2.3.51.2.4.1.6.1.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The size of the SSH public key represented by this entry.
| ||||
| CmmSshClientAuthPubKeyFingerprint | 1.3.6.1.4.1.2.3.51.2.4.1.6.1.1.5 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The RSA fingerprint of the SSH public key represented by this entry. This value can be used with the SSH client to verify, on the initial connection, that the Secure Shell server responding to the request is the server running on the managed entity. This is the fingerprint of the operational host key pair. If the key pair represented by this entry is not operational then sixteen null octets must be returned. | ||||
| CmmSshClientAuthPubKeyAcceptFrom | 1.3.6.1.4.1.2.3.51.2.4.1.6.1.1.6 | OCTET STRING | RW | mandatory |
column · OCTET STRING · read-write · mandatory This is a filter that describes the set of SSH client
IP addresses and host names that can establish
SSH connections to the MM authenticated by the public key
represented by this entry of the table. The filter is a
comma-separated list of IP addresses and/or hostnames.
A question mark may be used to match any single character.
An asterisk may be used to match multiple characters.
An exclamation point may preceed an IP address or hostname
to deny acccess from that IP address or hostname.
The format of the Accept From specification is:
from=PATTERN-LIST
PATTERN-LIST is the filter, which must be enclosed in
double quotation marks.
NOTE:This MIB object can be manipulated after the
corresponding SSH public key is installed. | ||||
| CmmSshClientAuthPubKeyComment | 1.3.6.1.4.1.2.3.51.2.4.1.6.1.1.7 | OCTET STRING | RW | mandatory |
column · OCTET STRING · read-write · mandatory This is a descriptive string that the administrator may use to help identify the public key represented by this entry. It serves no function in the operation of the SSH server. NOTE:This MIB object can be manipulated after the corresponding SSH public key is installed. | ||||
| CmmSshClientAuthPubKeyAction | 1.3.6.1.4.1.2.3.51.2.4.1.6.1.1.8 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory import(1) starts the TFTP file transfer of an SSH client authentication public key from the TFTP server to the MM. The import operation is only accepted if the associated RemoteAccessIdsEntry row is configured and the current value of mmSshClientAuthPubKeyEntryStatus is underCreation(3) or valid(1), if the current value of mmSshClientAuthPubKeyEntryStatus is valid(1), it will replace the key with a new key, If the import is successful the value of mmSshClientAuthPubKeyRowStatus changes to valid(1). export(2) starts the TFTP file transfer of an SSH client authentication public key from the MM to the TFTP server. The export operation is only accepted if the current value of mmSshClientAuthPubKeyEntryStatus is valid(1). NOTE: Users should compare the fingerprint value mmSshClientAuthPubKeyFingerprint to the fingerprint of client authentication key files imported or exported using the TFTP file transfer protocol to guard against possible file corruption. Value returned for the GET command is meaningless for this MIB object.
| ||||
| CmmSshClientAuthPubKeyEntryStatus | 1.3.6.1.4.1.2.3.51.2.4.1.6.1.1.9 | EntryStatus | RW | mandatory |
column · EntryStatus · read-write · mandatory This object manages the creation and deletion of this entry.
The steps recommended to install and to activate a new client
authorization public key are:
1. Set values for mmSshClientAuthPubKeyTftpServer,
mmSshClientAuthPubKeyFileName, mmSshClientAuthPubKeyFileFormat
2. Create a new entry in this table
mmSshClientAuthPubKeyEntryStatus = createRequest
3. Import a new key mmSshClientAuthPubKeyAction = import
This entry will be valid after mmSshClientAuthPubKeyAction
is successfully imported.
4. Set mmSshClientAuthPubKeyAcceptFrom and
mmSshClientAuthPubKeyComment as required.
valid(1) - Indicates that the public key pair represented
by this entry is available for use by the Secure
Shell Server for client authentication.
createRequest(2) - A new entry will be created in this table
for the specified host key pair and the new
entry will transition to the underCreation(3)
state. The operation is only accepted if the
associated RemoteAccessIdsEntry row defining
a local user account is configured.
underCreation(3) - Indicates that this entry exists in the
agent but is unavailable for use. After completing the
create operation, the agent will set this object to
underCreation(3).
invalid(4) - Deletes this entry and any client authentication
public key that may be associated with it.
Note: only one row may be created at one time. | ||||
| CmmSshClientAuthPubKeyUserId | 1.3.6.1.4.1.2.3.51.2.4.1.6.1.1.10 | OCTET STRING (SIZE (0..31)) | RO | mandatory |
column · OCTET STRING (SIZE (0..31)) · read-only · mandatory The userid for the key entry. | ||||
| SmmSshClientAuthPubKeyUnused | 1.3.6.1.4.1.2.3.51.2.4.1.6.2 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory The number of available storage locations that may be used to install additional Client Authentication Public Keys. This number decreases by one when a new key is added to the configuration. | ||||
| SmmSshClientAuthPubKeyTftpServer | 1.3.6.1.4.1.2.3.51.2.4.1.6.3 | OCTET STRING | RW | mandatory |
scalar · OCTET STRING · read-write · mandatory IP address or host name of the TFTP server where an SSH client authentication public key is to be installed from or exported to. The address must be entered in a dotted decimal IP string (e.g. 9.37.44.2). | ||||
| SmmSshClientAuthPubKeyFileName | 1.3.6.1.4.1.2.3.51.2.4.1.6.4 | OCTET STRING | RW | mandatory |
scalar · OCTET STRING · read-write · mandatory File name on the TFTP server of an SSH client authentication public key. | ||||
| SmmSshClientAuthPubKeyFileFormat | 1.3.6.1.4.1.2.3.51.2.4.1.6.5 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory File format of SSH client authentication public key files imported from or exported to the TFTP file server.
| ||||
| NgroupProfiles | 1.3.6.1.4.1.2.3.51.2.4.1.7 | |||
| TgroupIdsTable | 1.3.6.1.4.1.2.3.51.2.4.1.7.1 | NA | mandatory | |
table · not-accessible · mandatory Table of Group profiles. This table lets you to configure all group profiles. You can define up to 16 unique profiles. | ||||
| RgroupIdsEntry | 1.3.6.1.4.1.2.3.51.2.4.1.7.1.1 | NA | mandatory | |
| CgroupIndex | 1.3.6.1.4.1.2.3.51.2.4.1.7.1.1.1 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Index for Group IDs entry. | ||||
| CgroupId | 1.3.6.1.4.1.2.3.51.2.4.1.7.1.1.2 | OCTET STRING (SIZE (0..16)) | RW | mandatory |
column · OCTET STRING (SIZE (0..16)) · read-write · mandatory Group ID. It is a null terminated string that contains the group-id. It must not be a duplicate of any previously configured ones. | ||||
| CgroupRole | 1.3.6.1.4.1.2.3.51.2.4.1.7.1.1.3 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Group Role. It indicates if the group has supervisor, operator, or custom access. | ||||
| CgroupEntryStatus | 1.3.6.1.4.1.2.3.51.2.4.1.7.1.1.9 | EntryStatus | RW | mandatory |
column · EntryStatus · read-write · mandatory This object manages the creation and deletion of this entry.
The steps recommended to add a new group are:
1. Create a new entry in this table
groupEntryStatus = createRequest
2. Set groupId as required.
Then the entry will be valid.
valid(1) - Indicates that the group represented
by this entry is available for use.
createRequest(2) - A new entry will be created in this table
for the specified group and the new entry
will transition to the underCreation(3).
underCreation(3) - Indicates that this entry exists in the
agent but is unavailable for use. After completing the
create operation, the agent will set this object to
underCreation(3).
invalid(4) - Deletes this entry. | ||||
| TgroupRBSroleTable | 1.3.6.1.4.1.2.3.51.2.4.1.7.2 | NA | mandatory | |
table · not-accessible · mandatory Table of Group Role profiles. | ||||
| RgroupRBSroleEntry | 1.3.6.1.4.1.2.3.51.2.4.1.7.2.1 | NA | mandatory | |
| CgroupRBSroleIndex | 1.3.6.1.4.1.2.3.51.2.4.1.7.2.1.1 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Index for Group Role entry. | ||||
| CgroupRBSroleId | 1.3.6.1.4.1.2.3.51.2.4.1.7.2.1.2 | OCTET STRING (SIZE (0..16)) | RO | mandatory |
column · OCTET STRING (SIZE (0..16)) · read-only · mandatory Group ID | ||||
| CgroupRBSSupervisor | 1.3.6.1.4.1.2.3.51.2.4.1.7.2.1.3 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Group has no restrictions.
| ||||
| CgroupRBSOperator | 1.3.6.1.4.1.2.3.51.2.4.1.7.2.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Group has read-only access, and cannot perform any save, modify, clear, or state affecting operations (e.g. restart MM, restore defaults, upgrade the firmware, etc.).
| ||||
| CgroupRBSChassisOperator | 1.3.6.1.4.1.2.3.51.2.4.1.7.2.1.5 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Group has ability to browse status and properties of chassis components (MM, chassis fans, midplane, power modules). Ability to backup MM configuration to a file. Saving MM configuration to chassis requires supervisor access.
| ||||
| CgroupRBSChassisAccountManagement | 1.3.6.1.4.1.2.3.51.2.4.1.7.2.1.6 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Group can add/modify/delete user login profiles. Ability to backup MM configuration to a file. Changing global login settings require chassis configuration authority.
| ||||
| CgroupRBSChassisLogManagement | 1.3.6.1.4.1.2.3.51.2.4.1.7.2.1.7 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Group has ability to clear the MM event log, change log policy settings, and backup MM configuration to a file.
| ||||
| CgroupRBSChassisConfiguration | 1.3.6.1.4.1.2.3.51.2.4.1.7.2.1.8 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Group can modify and save any chassis configuration parameter (except user profiles and event log settings). Ability to restore MM factory defaults if the group also has chassis administration permissions. Ability to change the global login settings, SOL configuration, and backup MM configuration to a file.
| ||||
| CgroupRBSChassisAdministration | 1.3.6.1.4.1.2.3.51.2.4.1.7.2.1.9 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Group has ability to do MM firmware updates, modify chassis LEDs, restore MM factory defaults if the group also has chassis configuration permissions. Ability to restart MM and backup MM configuration to a file.
| ||||
| CgroupRBSBladeOperator | 1.3.6.1.4.1.2.3.51.2.4.1.7.2.1.10 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Group has ability to browse status and properties of blades.
| ||||
| CgroupRBSBladeRemotePresence | 1.3.6.1.4.1.2.3.51.2.4.1.7.2.1.11 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Group has ability to access the blade remote console The ability to issue the CLI console command to start an SOL session to a blade will also require this authority.
| ||||
| CgroupRBSBladeConfiguration | 1.3.6.1.4.1.2.3.51.2.4.1.7.2.1.12 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Group can modify and save any blade configuration parameter.
| ||||
| CgroupRBSBladeAdministration | 1.3.6.1.4.1.2.3.51.2.4.1.7.2.1.13 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Group can power on/off and restart blades, activate standby blades, do firmware updates, and modify blade LEDs.
| ||||
| CgroupRBSSwitchModuleOperator | 1.3.6.1.4.1.2.3.51.2.4.1.7.2.1.14 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Group has ability to browse status and properties of I/O Modules, and to ping I/O Modules.
| ||||
| CgroupRBSSwitchModuleConfiguration | 1.3.6.1.4.1.2.3.51.2.4.1.7.2.1.15 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Group can modify the I/O Module IP address, configure I/O Module Advanced Management parameters, and restore factory defaults on an I/O Module. Note that a group requires both I/O Module configuration and I/O Module administration roles in order to be able to launch a telnet session to an I/O Module, or to restore factory defaults on an I/O Module.
| ||||
| CgroupRBSSwitchModuleAdministration | 1.3.6.1.4.1.2.3.51.2.4.1.7.2.1.16 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Group can power on/off and restart the I/O Modules, update I/O Module firmware, enable/disable the Fast POST and External Ports of an I/O Module. Note that a group requires both I/O Module configuration and I/O Module administration roles in order to be able to launch a telnet session to an I/O Module, or to restore factory defaults on an I/O Module.
| ||||
| TgroupRBSscopeTable | 1.3.6.1.4.1.2.3.51.2.4.1.7.3 | NA | mandatory | |
table · not-accessible · mandatory Table of Group Scope profiles. | ||||
| RgroupRBSscopeEntry | 1.3.6.1.4.1.2.3.51.2.4.1.7.3.1 | NA | mandatory | |
| CgroupRBSscopeIndex | 1.3.6.1.4.1.2.3.51.2.4.1.7.3.1.1 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Index for Group Scope Entry. | ||||
| CgroupRBSscopeId | 1.3.6.1.4.1.2.3.51.2.4.1.7.3.1.2 | OCTET STRING (SIZE (0..16)) | RO | mandatory |
column · OCTET STRING (SIZE (0..16)) · read-only · mandatory Group ID | ||||
| CgroupRBSChassis | 1.3.6.1.4.1.2.3.51.2.4.1.7.3.1.3 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Group has access to the MM and chassis functions.
| ||||
| CgroupRBSBlade1 | 1.3.6.1.4.1.2.3.51.2.4.1.7.3.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Group has access to the blade in slot 1.
| ||||
| CgroupRBSBlade2 | 1.3.6.1.4.1.2.3.51.2.4.1.7.3.1.5 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Group has access to the blade in slot 2.
| ||||
| CgroupRBSBlade3 | 1.3.6.1.4.1.2.3.51.2.4.1.7.3.1.6 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Group has access to the blade in slot 3.
| ||||
| CgroupRBSBlade4 | 1.3.6.1.4.1.2.3.51.2.4.1.7.3.1.7 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Group has access to the blade in slot 4.
| ||||
| CgroupRBSBlade5 | 1.3.6.1.4.1.2.3.51.2.4.1.7.3.1.8 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Group has access to the blade in slot 5.
| ||||
| CgroupRBSBlade6 | 1.3.6.1.4.1.2.3.51.2.4.1.7.3.1.9 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Group has access to the blade in slot 6.
| ||||
| CgroupRBSBlade7 | 1.3.6.1.4.1.2.3.51.2.4.1.7.3.1.10 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Group has access to the blade in slot 7.
| ||||
| CgroupRBSBlade8 | 1.3.6.1.4.1.2.3.51.2.4.1.7.3.1.11 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Group has access to the blade in slot 8.
| ||||
| CgroupRBSBlade9 | 1.3.6.1.4.1.2.3.51.2.4.1.7.3.1.12 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Group has access to the blade in slot 9.
| ||||
| CgroupRBSBlade10 | 1.3.6.1.4.1.2.3.51.2.4.1.7.3.1.13 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Group has access to the blade in slot 10.
| ||||
| CgroupRBSBlade11 | 1.3.6.1.4.1.2.3.51.2.4.1.7.3.1.14 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Group has access to the blade in slot 11.
| ||||
| CgroupRBSBlade12 | 1.3.6.1.4.1.2.3.51.2.4.1.7.3.1.15 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Group has access to the blade in slot 12.
| ||||
| CgroupRBSBlade13 | 1.3.6.1.4.1.2.3.51.2.4.1.7.3.1.16 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Group has access to the blade in slot 13.
| ||||
| CgroupRBSBlade14 | 1.3.6.1.4.1.2.3.51.2.4.1.7.3.1.17 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Group has access to the blade in slot 14.
| ||||
| CgroupRBSSwitch1 | 1.3.6.1.4.1.2.3.51.2.4.1.7.3.1.18 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Group has access to I/O module 1.
| ||||
| CgroupRBSSwitch2 | 1.3.6.1.4.1.2.3.51.2.4.1.7.3.1.19 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Group has access to I/O module 2.
| ||||
| CgroupRBSSwitch3 | 1.3.6.1.4.1.2.3.51.2.4.1.7.3.1.20 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Group has access to I/O module 3.
| ||||
| CgroupRBSSwitch4 | 1.3.6.1.4.1.2.3.51.2.4.1.7.3.1.21 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Group has access to I/O module 4.
| ||||
| CgroupRBSSwitch5 | 1.3.6.1.4.1.2.3.51.2.4.1.7.3.1.22 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Group has access to I/O module 5.
| ||||
| CgroupRBSSwitch6 | 1.3.6.1.4.1.2.3.51.2.4.1.7.3.1.23 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Group has access to I/O module 6.
| ||||
| CgroupRBSSwitch7 | 1.3.6.1.4.1.2.3.51.2.4.1.7.3.1.24 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Group has access to I/O module 7.
| ||||
| CgroupRBSSwitch8 | 1.3.6.1.4.1.2.3.51.2.4.1.7.3.1.25 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Group has access to I/O module 8.
| ||||
| CgroupRBSSwitch9 | 1.3.6.1.4.1.2.3.51.2.4.1.7.3.1.26 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Group has access to I/O module 9.
| ||||
| CgroupRBSSwitch10 | 1.3.6.1.4.1.2.3.51.2.4.1.7.3.1.27 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Group has access to I/O module 10.
| ||||
| NremoteAlerts | 1.3.6.1.4.1.2.3.51.2.4.2 | |||
| NremoteAlertsCrit | 1.3.6.1.4.1.2.3.51.2.4.2.1 | |||
| ScritPower | 1.3.6.1.4.1.2.3.51.2.4.2.1.5 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Generate an alert if any of the system power supplies fail.
| ||||
| ScritBlade | 1.3.6.1.4.1.2.3.51.2.4.2.1.10 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Generate an alert for any critical error condition on a blade.
| ||||
| ScritIO | 1.3.6.1.4.1.2.3.51.2.4.2.1.11 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Generate an alert for any critical error condition on I/O module.
| ||||
| ScritStorage | 1.3.6.1.4.1.2.3.51.2.4.2.1.12 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Generate an alert for any critical error condition on a Storage module.
| ||||
| ScritChassis | 1.3.6.1.4.1.2.3.51.2.4.2.1.13 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Generate an alert for any critical error condition on chassis.
| ||||
| ScritFan | 1.3.6.1.4.1.2.3.51.2.4.2.1.14 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Generate an alert for any critical error condition on cooling devices.
| ||||
| NremoteAlertsNonCrit | 1.3.6.1.4.1.2.3.51.2.4.2.2 | |||
| SwarnLogFull | 1.3.6.1.4.1.2.3.51.2.4.2.2.10 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Generate an alert if the system log reaches 100% full.
| ||||
| SwarnBlade | 1.3.6.1.4.1.2.3.51.2.4.2.2.15 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Generate an alert for any warning condition on a blade.
| ||||
| SwarnIO | 1.3.6.1.4.1.2.3.51.2.4.2.2.16 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Generate an alert for any warning condition on I/O module.
| ||||
| SwarnStorage | 1.3.6.1.4.1.2.3.51.2.4.2.2.17 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Generate an alert for any warning condition on a Storage module.
| ||||
| SwarnPower | 1.3.6.1.4.1.2.3.51.2.4.2.2.18 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Generate an alert for any warning condition on power module.
| ||||
| SwarnChassis | 1.3.6.1.4.1.2.3.51.2.4.2.2.19 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Generate an alert for any warning condition on chassis.
| ||||
| SwarnFan | 1.3.6.1.4.1.2.3.51.2.4.2.2.20 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Generate an alert for any warning condition on cooling devices.
| ||||
| NremoteAlertsSystem | 1.3.6.1.4.1.2.3.51.2.4.2.3 | |||
| SsystemInventory | 1.3.6.1.4.1.2.3.51.2.4.2.3.10 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Generate an alert if the a processor blade or media tray is added or removed.
| ||||
| SsystemLog75PctFull | 1.3.6.1.4.1.2.3.51.2.4.2.3.11 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Generate an alert if the system log reaches 75% full.
| ||||
| SnetworkChangeNotification | 1.3.6.1.4.1.2.3.51.2.4.2.3.12 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Generate an alert if the MM has restarted and the internal network has initialized successfully, or if an IP address change via a source other than the management module.
| ||||
| SsystemRemoteLogin | 1.3.6.1.4.1.2.3.51.2.4.2.3.15 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Generate an alert if the system detects a new user logged in from a remote site.
| ||||
| SsystemBlade | 1.3.6.1.4.1.2.3.51.2.4.2.3.16 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Generate an alert for any informational condition on a blade.
| ||||
| SsystemIO | 1.3.6.1.4.1.2.3.51.2.4.2.3.17 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Generate an alert for any informational condition on I/O module.
| ||||
| SsystemStorage | 1.3.6.1.4.1.2.3.51.2.4.2.3.18 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Generate an alert for any informational condition on a Storage module.
| ||||
| SsystemPower | 1.3.6.1.4.1.2.3.51.2.4.2.3.19 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Generate an alert for any informational condition on power module.
| ||||
| SsystemChassis | 1.3.6.1.4.1.2.3.51.2.4.2.3.20 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Generate an alert for any informational condition on chassis.
| ||||
| SsystemFan | 1.3.6.1.4.1.2.3.51.2.4.2.3.21 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Generate an alert for any informational condition on cooling device.
| ||||
| SsystemPWRDO | 1.3.6.1.4.1.2.3.51.2.4.2.3.22 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Generate an alert for any informational condition on power on and power off.
| ||||
| NsecuritySettings | 1.3.6.1.4.1.2.3.51.2.4.3 | |||
| StrespassWarning | 1.3.6.1.4.1.2.3.51.2.4.3.2 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory If enabled, a customizable trespass warning message is displayed via the Web and CLI interfaces.
| ||||
| StrespassWarningDefault | 1.3.6.1.4.1.2.3.51.2.4.3.3 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Reset the trespass warning to default value. NOTE: Value returned for the GET command is meaningless for this MIB object.
| ||||
| StrespassMessage | 1.3.6.1.4.1.2.3.51.2.4.3.4 | OCTET STRING (SIZE (0..1600)) | RW | mandatory |
scalar · OCTET STRING (SIZE (0..1600)) · read-write · mandatory The value of the trespass warning message. | ||||
| NchassisSecuritySettings | 1.3.6.1.4.1.2.3.51.2.4.3.5 | |||
| SsecurityPolicySetting | 1.3.6.1.4.1.2.3.51.2.4.3.5.1 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Determines chassis security policy. legacy mode(0) or secure mode(1). unknown(255) returned when policy can't be set or determined.
| ||||
| SsecurityPolicyState | 1.3.6.1.4.1.2.3.51.2.4.3.5.2 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory Determines chassis security policy state. If pending(0), check securityPolicyStatusTable for details on actions needed, to make fully active.
| ||||
| TsecurityPolicyStatusTable | 1.3.6.1.4.1.2.3.51.2.4.3.5.3 | NA | mandatory | |
table · not-accessible · mandatory Table of pending security policy status. | ||||
| RsecurityPolicyStatusEntry | 1.3.6.1.4.1.2.3.51.2.4.3.5.3.1 | NA | mandatory | |
| CsecurityPolicyStatusIndex | 1.3.6.1.4.1.2.3.51.2.4.3.5.3.1.1 | INTEGER (0..128) | RO | mandatory |
column · INTEGER (0..128) · read-only · mandatory Pending Security policy status index. | ||||
| CsecurityPolicyStatusComponentType | 1.3.6.1.4.1.2.3.51.2.4.3.5.3.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates Component type and location with pending security status.
| ||||
| CsecurityPolicyStatusBayId | 1.3.6.1.4.1.2.3.51.2.4.3.5.3.1.3 | INTEGER (0..14) | RO | mandatory |
column · INTEGER (0..14) · read-only · mandatory Bay location of specific component. NOTE: securityPolicyStatusComponentType enumeration also indicates location. | ||||
| CsecurityPolicyStatusSummary | 1.3.6.1.4.1.2.3.51.2.4.3.5.3.1.4 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Summary of pending security status for the component. | ||||
| CsecurityPolicyStatusDetails | 1.3.6.1.4.1.2.3.51.2.4.3.5.3.1.5 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Details of pending security status for the component. | ||||
| Ncryptography | 1.3.6.1.4.1.2.3.51.2.4.3.5.10 | |||
| ScryptographySummary | 1.3.6.1.4.1.2.3.51.2.4.3.5.10.5 | OCTET STRING | RO | mandatory |
scalar · OCTET STRING · read-only · mandatory The current level and summary description of the cryptographic configuration. | ||||
| ScryptographyMode | 1.3.6.1.4.1.2.3.51.2.4.3.5.10.15 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory The NIST cryptographic mode setting. A successful setting of this object initiates a reboot of the CMM within a few seconds.
| ||||
| TcryptographyModeDetailsTable | 1.3.6.1.4.1.2.3.51.2.4.3.5.10.18 | NA | mandatory | |
table · not-accessible · mandatory A table of information indicating any NIST customization details and any reasons that the CMM cannot transition to the desired NIST mode. | ||||
| RcryptographyModeDetailsEntry | 1.3.6.1.4.1.2.3.51.2.4.3.5.10.18.1 | NA | mandatory | |
| CcryptographyModeDetailsIndex | 1.3.6.1.4.1.2.3.51.2.4.3.5.10.18.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Cryptography mode details index. | ||||
| CcryptographyModeDetailsType | 1.3.6.1.4.1.2.3.51.2.4.3.5.10.18.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indication of what type of message is reported for this entry.
| ||||
| CcryptographyModeDetailsDescription | 1.3.6.1.4.1.2.3.51.2.4.3.5.10.18.1.3 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Message containing details for this cryptography entry. | ||||
| TcryptographyModeComponentTable | 1.3.6.1.4.1.2.3.51.2.4.3.5.10.20 | NA | mandatory | |
table · not-accessible · mandatory A table of information listing any IOMs or nodes that require a firmware update in order for the CMM to transition to the new mode. | ||||
| RcryptographyModeComponentEntry | 1.3.6.1.4.1.2.3.51.2.4.3.5.10.20.1 | NA | mandatory | |
row · not-accessible · mandatory Cryptography mode component entry | ||||
| CcryptographyModeComponentIndex | 1.3.6.1.4.1.2.3.51.2.4.3.5.10.20.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Cryptography mode component index. | ||||
| CcryptographyModeComponentId | 1.3.6.1.4.1.2.3.51.2.4.3.5.10.20.1.2 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory A component identifier for an IOM or node in the form: ts:mm. t(type), s(slot number), mm sub-slot number. | ||||
| ScryptographicCipher | 1.3.6.1.4.1.2.3.51.2.4.3.5.10.25 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory The cryptographic cipher suite setting.
| ||||
| TcryptographyCipherComponentTable | 1.3.6.1.4.1.2.3.51.2.4.3.5.10.30 | NA | mandatory | |
table · not-accessible · mandatory A table of information listing any IOMs or nodes that are out of compliance with regards to the cipher suite setting and are therefore preventing the CMM from transitioning to the new cipher mode. | ||||
| RcryptographyCipherComponentEntry | 1.3.6.1.4.1.2.3.51.2.4.3.5.10.30.1 | NA | mandatory | |
row · not-accessible · mandatory Cryptography cipher component entry | ||||
| CcryptographyCipherComponentIndex | 1.3.6.1.4.1.2.3.51.2.4.3.5.10.30.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Cryptography cipher component index. | ||||
| CcryptographyCipherComponentId | 1.3.6.1.4.1.2.3.51.2.4.3.5.10.30.1.2 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory A component identifier for an IOM or node in the form: ts:mm. t(type), s(slot number), mm sub-slot number. | ||||
| ScipherStrength | 1.3.6.1.4.1.2.3.51.2.4.3.5.15 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Strength level of the NIST signing algorithm for certificate authority. None(0) indicates no signing algorithm has been set. When writing a new value to this object, a result of No Error is returned if the value is valid. However, the new algorithm will be used to create an authority certificate asynchronously. This process may take up to 1 minute to complete. So results for subsequent queries to the object's value may also be delayed while the new certificate is being generated.
| ||||
| NspClock | 1.3.6.1.4.1.2.3.51.2.4.4 | |||
| SspClockDateAndTimeSetting | 1.3.6.1.4.1.2.3.51.2.4.4.1 | OCTET STRING | RW | mandatory |
scalar · OCTET STRING · read-write · mandatory MM clock date and time setting. A date-time specification for the local time of day. For example to set the date and time to March 4, 2001 at 06:00:00AM, set the value to:'03/04/2001,06:00:00'. field contents range _____ ________ _____ 1 month 01..12 2 separator '/' 3 day 01..31 4 separator '/' 5 year 2000..2089 6 separator ',' 7 hour 00..23 8 separator ':' 9 minutes 00..59 10 separator ':' 11 seconds 00..59 | ||||
| SspClockTimezoneSetting | 1.3.6.1.4.1.2.3.51.2.4.4.2 | OCTET STRING | RW | mandatory |
scalar · OCTET STRING · read-write · mandatory MM clock Greenwich Mean Time(GMT) offset and Daylight Saving Time(DST) settings. For write, the value must be a time zone listed in spClockTimezoneTable. The spClockTimezoneTable lists all valid time zones. Example: To set America's New York time zone, set the value to: 'America/New_York' For read, the value format is <offset>,<DST flag>,<time zone> (<comment>) Example: -4:00,yes,America/New_York (Eastern Time) | ||||
| TspClockTimezoneTable | 1.3.6.1.4.1.2.3.51.2.4.4.3 | NA | mandatory | |
table · not-accessible · mandatory Table of all time zones listed in zone.tab file | ||||
| RspClockTimezoneEntry | 1.3.6.1.4.1.2.3.51.2.4.4.3.1 | NA | mandatory | |
| CspClockTimezoneIndex | 1.3.6.1.4.1.2.3.51.2.4.4.3.1.1 | INTEGER (0..1000) | RO | mandatory |
column · INTEGER (0..1000) · read-only · mandatory Time zone table index. | ||||
| CspClockTimezoneId | 1.3.6.1.4.1.2.3.51.2.4.4.3.1.2 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Time zone instance id. | ||||
| CspClockTimezoneCaption | 1.3.6.1.4.1.2.3.51.2.4.4.3.1.3 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Time zone caption. | ||||
| CspClockTimezoneDescription | 1.3.6.1.4.1.2.3.51.2.4.4.3.1.4 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Time zone description. | ||||
| CspClockTimezoneName | 1.3.6.1.4.1.2.3.51.2.4.4.3.1.5 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Time zone name. | ||||
| CspClockTimezoneStandardName | 1.3.6.1.4.1.2.3.51.2.4.4.3.1.6 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Time zone standard name. | ||||
| CspClockTimezoneStandardCaption | 1.3.6.1.4.1.2.3.51.2.4.4.3.1.7 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Time zone standard caption. | ||||
| CspClockTimezoneDaylightName | 1.3.6.1.4.1.2.3.51.2.4.4.3.1.8 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Time zone daylight name. | ||||
| CspClockTimezoneDaylightCaption | 1.3.6.1.4.1.2.3.51.2.4.4.3.1.9 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Time zone daylight caption. | ||||
| CspClockTimezoneCmmOffset | 1.3.6.1.4.1.2.3.51.2.4.4.3.1.10 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory CMM offset. | ||||
| CspClockTimezoneStandardOffsetMinutes | 1.3.6.1.4.1.2.3.51.2.4.4.3.1.11 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Standard GMT offset in minutes. | ||||
| CspClockTimezoneStandardDaylightOffsetMinutes | 1.3.6.1.4.1.2.3.51.2.4.4.3.1.12 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Standard GMT offset in minutes. | ||||
| CspClockTimezoneDaylightDay | 1.3.6.1.4.1.2.3.51.2.4.4.3.1.13 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory There are two different interpretations for this field, depending on the value of DaylightDayOfWeek.
In one case, DaylightDay defines the day-in-month on which daylight saving time starts.
This interpretation is used when the DaylightDayOfWeek is 0.
A positive or negative integer is specified to indicate whether the DaylightDay is calculated
from the beginning or the end of the month.
For example, 5 indicates the fifth day in the DaylightMonth and -1 indicates the last day in the DaylightMonth.
When DaylightDayOfWeek is not 0, DaylightDay is the day in the month on which daylight saving time starts,
as defined in conjunction with DaylightDayOfWeek.
For example, if DaylightDay is 15 and DaylightDayOfWeek is Saturday, then daylight saving time starts
on the first Saturday on or after the 15th day in the DaylightMonth (that is, the third Saturday in the month).
If DaylightDay is 20 and DaylightDayOfWeek is -Saturday, then this indicates the first Saturday on or before
the 20th day in the DaylightMonth.
If DaylightDay is -1 and DaylightDayOfWeek is -Sunday, then this indicates the last Sunday in the month.
| ||||
| CspClockTimezoneDaylightDayOfWeek | 1.3.6.1.4.1.2.3.51.2.4.4.3.1.14 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Day of week daylight saving begins.
| ||||
| CspClockTimezoneDaylightMonth | 1.3.6.1.4.1.2.3.51.2.4.4.3.1.15 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Month daylight saving begins.
| ||||
| CspClockTimezoneDaylightStandardDay | 1.3.6.1.4.1.2.3.51.2.4.4.3.1.16 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory There are two different interpretations for this property, depending on the value of StandardDayOfWeek. In one case, StandardDay defines the day-in-month on which daylight saving time ends. This interpretation is used when the StandardDayOfWeek is 0. A positive or negative integer is specified to indicate whether the StandardDay is calculated from the beginning or the end of the month. For example, 5 indicates the fifth day in the StandardMonth and -1 indicates the last day in the StandardMonth. When StandardDayOfWeek is not 0, StandardDay is the day-in-month on which daylight saving time ends, as defined in conjunction with StandardDayOfWeek. For example, if StandardDay is 15 and StandardDayOfWeek is Saturday, then daylight saving time ends on the first Saturday on or after the 15th day in the StandardMonth (that is, the third Saturday in the month). If StandardDay is 20 and StandardDayOfWeek is -Saturday, then this indicates the first Saturday on or before the 20 th day in the StandardMonth. If StandardDay is -1 and StandardDayOfWeek is -Sunday, then this indicates the last Sunday in the StandardMonth.
| ||||
| CspClockTimezoneDaylightStandardDayOfWeek | 1.3.6.1.4.1.2.3.51.2.4.4.3.1.17 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Day of week daylight saving ends.
| ||||
| CspClockTimezoneDaylightStandardMonth | 1.3.6.1.4.1.2.3.51.2.4.4.3.1.18 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Month daylight saving ends.
| ||||
| CspClockTimezoneDaylightIntervalInMinutes | 1.3.6.1.4.1.2.3.51.2.4.4.3.1.19 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Interval in minutes (Daylight saving begins). | ||||
| CspClockTimezoneDaylightStandardInMinutes | 1.3.6.1.4.1.2.3.51.2.4.4.3.1.20 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Interval in minutes (Daylight saving ends). | ||||
| SspClockTimezoneDaylightStart | 1.3.6.1.4.1.2.3.51.2.4.4.5 | OCTET STRING | RO | mandatory |
scalar · OCTET STRING · read-only · mandatory DST start. | ||||
| SspClockTimezoneDaylightEnd | 1.3.6.1.4.1.2.3.51.2.4.4.6 | OCTET STRING | RO | mandatory |
scalar · OCTET STRING · read-only · mandatory DST end. | ||||
| NspIdentification | 1.3.6.1.4.1.2.3.51.2.4.5 | |||
| SspTxtId | 1.3.6.1.4.1.2.3.51.2.4.5.1 | OCTET STRING (SIZE (0..16)) | RW | mandatory |
scalar · OCTET STRING (SIZE (0..16)) · read-write · mandatory Text description of the MM. NOTE: Do not put any 'space characters' at end of the string. | ||||
| NnetworkConfiguration | 1.3.6.1.4.1.2.3.51.2.4.9 | |||
| NnetworkInterfaces | 1.3.6.1.4.1.2.3.51.2.4.9.1 | |||
| NextEthernetInterface | 1.3.6.1.4.1.2.3.51.2.4.9.1.1 | |||
| SextEthernetInterfaceType | 1.3.6.1.4.1.2.3.51.2.4.9.1.1.1 | OCTET STRING (SIZE (0..16)) | RO | mandatory |
scalar · OCTET STRING (SIZE (0..16)) · read-only · mandatory The type of interface. | ||||
| SextEthernetInterfaceHostName | 1.3.6.1.4.1.2.3.51.2.4.9.1.1.3 | OCTET STRING (SIZE (0..64)) | RW | mandatory |
scalar · OCTET STRING (SIZE (0..64)) · read-write · mandatory Contains the 64 byte null terminated DNS host name for this interface. | ||||
| SextEthernetInterfaceIPAddress | 1.3.6.1.4.1.2.3.51.2.4.9.1.1.4 | IpAddress | RW | mandatory |
scalar · IpAddress · read-write · mandatory Contains the IP address for the ethernet interface. | ||||
| SextEthernetInterfaceDataRate | 1.3.6.1.4.1.2.3.51.2.4.9.1.1.5 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Specifies the data transfer rate to be used over the ethernet interface: 10Mb, 100Mb, 1G or Auto.
| ||||
| SextEthernetInterfaceDuplexSetting | 1.3.6.1.4.1.2.3.51.2.4.9.1.1.6 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Specifies the duplex settings for the data transfer rate to be used over the ethernet interface: Half, Full, or Auto.
| ||||
| SextEthernetInterfaceLAA | 1.3.6.1.4.1.2.3.51.2.4.9.1.1.7 | OCTET STRING (SIZE (17)) | RW | mandatory |
scalar · OCTET STRING (SIZE (17)) · read-write · mandatory Specifies the locally administered MAC address. The locally administered address must be a hexadecimal value between 000000000000 - FFFFFFFFFFFF. This value must be in the form XX:XX:XX:XX:XX:XX where 'X' is a number between 0 - 9 and A - F. This MM subsystem does not allow use of a multicast address. A multicast address has the least significant bit of the first byte set to a 1. The first byte must, therefore, be an even number. NOTE: Although the locally administered MAC address can be assigned the same value for the primary and backup MM, it is not recommended. | ||||
| SextEthernetInterfaceDhcpEnabled | 1.3.6.1.4.1.2.3.51.2.4.9.1.1.8 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Disable or enable DHCP on this interface.
| ||||
| SextEthernetInterfaceGatewayIPAddress | 1.3.6.1.4.1.2.3.51.2.4.9.1.1.9 | IpAddress | RW | mandatory |
scalar · IpAddress · read-write · mandatory Contains the IP address of the gateway/router for the ethernet interface. | ||||
| SextEthernetInterfaceBIA | 1.3.6.1.4.1.2.3.51.2.4.9.1.1.10 | OCTET STRING (SIZE (17)) | RO | mandatory |
scalar · OCTET STRING (SIZE (17)) · read-only · mandatory Specifies the burned-in MAC (BIA) address. | ||||
| SextEthernetInterfaceMTU | 1.3.6.1.4.1.2.3.51.2.4.9.1.1.13 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Contains the Maximum Transmission Unit(MTU) for the ethernet interface | ||||
| SextEthernetInterfaceSubnetMask | 1.3.6.1.4.1.2.3.51.2.4.9.1.1.14 | IpAddress | RW | mandatory |
scalar · IpAddress · read-write · mandatory Contains the subnet mask for the ethernet interface | ||||
| NdhcpEthernetInterface | 1.3.6.1.4.1.2.3.51.2.4.9.1.1.16 | |||
| SdhcpHostName | 1.3.6.1.4.1.2.3.51.2.4.9.1.1.16.1 | OCTET STRING (SIZE (0..64)) | RO | mandatory |
scalar · OCTET STRING (SIZE (0..64)) · read-only · mandatory Contains the 64 byte null terminated DNS host name for this interface, assigned by the DHCP server. | ||||
| SdhcpIPAddress | 1.3.6.1.4.1.2.3.51.2.4.9.1.1.16.2 | IpAddress | RO | mandatory |
scalar · IpAddress · read-only · mandatory Contains the IP address for the ethernet interface, assigned by the DHCP server. | ||||
| SdhcpGatewayIPAddress | 1.3.6.1.4.1.2.3.51.2.4.9.1.1.16.3 | IpAddress | RO | mandatory |
scalar · IpAddress · read-only · mandatory Contains the IP address of the gateway/router for the ethernet interface, assigned by the DHCP server. | ||||
| SdhcpSubnetMask | 1.3.6.1.4.1.2.3.51.2.4.9.1.1.16.4 | IpAddress | RO | mandatory |
scalar · IpAddress · read-only · mandatory Contains the Subnet Mask for the ethernet interface, assigned by the DHCP server. | ||||
| SdhcpDomainName | 1.3.6.1.4.1.2.3.51.2.4.9.1.1.16.5 | OCTET STRING (SIZE (0..64)) | RO | mandatory |
scalar · OCTET STRING (SIZE (0..64)) · read-only · mandatory Contains the 64 byte null terminated Domain Name for this interface, assigned by the DHCP server. | ||||
| SdhcpDHCPServer | 1.3.6.1.4.1.2.3.51.2.4.9.1.1.16.6 | IpAddress | RO | mandatory |
scalar · IpAddress · read-only · mandatory Contains the DHCP server IP address used to acquire the DHCP settings. | ||||
| SdhcpPrimaryDNSServer | 1.3.6.1.4.1.2.3.51.2.4.9.1.1.16.7 | IpAddress | RO | mandatory |
scalar · IpAddress · read-only · mandatory Contains the Primary DNS server, assigned by the DHCP server. | ||||
| SdhcpSecondaryDNSServer | 1.3.6.1.4.1.2.3.51.2.4.9.1.1.16.8 | IpAddress | RO | mandatory |
scalar · IpAddress · read-only · mandatory Contains the Secondary DNS server, assigned by the DHCP server. | ||||
| SdhcpTertiaryDNSServer | 1.3.6.1.4.1.2.3.51.2.4.9.1.1.16.9 | IpAddress | RO | mandatory |
scalar · IpAddress · read-only · mandatory Contains the tertiary DNS server, assigned by the DHCP server. | ||||
| SextEthernetInterfaceFloatingIPAddress | 1.3.6.1.4.1.2.3.51.2.4.9.1.1.22 | IpAddress | RW | mandatory |
scalar · IpAddress · read-write · mandatory Contains the floating IP address for the external ethernet interface. | ||||
| NstandbyExtEthernetInterface | 1.3.6.1.4.1.2.3.51.2.4.9.1.3 | |||
| SstandbyExtEthernetInterfaceType | 1.3.6.1.4.1.2.3.51.2.4.9.1.3.1 | OCTET STRING (SIZE (0..16)) | RO | mandatory |
scalar · OCTET STRING (SIZE (0..16)) · read-only · mandatory The type of interface. NOTE: This MIB object is only applicable to systems with a standby MM. | ||||
| SstandbyExtEthernetInterfaceHostName | 1.3.6.1.4.1.2.3.51.2.4.9.1.3.3 | OCTET STRING (SIZE (0..64)) | RW | mandatory |
scalar · OCTET STRING (SIZE (0..64)) · read-write · mandatory Contains the 64 byte null terminated DNS host name for this interface. NOTE: This MIB object is only applicable to systems with a standby MM. | ||||
| SstandbyExtEthernetInterfaceIPAddress | 1.3.6.1.4.1.2.3.51.2.4.9.1.3.4 | IpAddress | RW | mandatory |
scalar · IpAddress · read-write · mandatory Contains the IP address for the ethernet interface. NOTE: This MIB object is only applicable to systems with a standby MM. | ||||
| SstandbyExtEthernetInterfaceDataRate | 1.3.6.1.4.1.2.3.51.2.4.9.1.3.5 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Specifies the data transfer rate to be used over the ethernet interface: 10Mb, 100Mb, 1G or Auto. NOTE: This MIB object is only applicable to systems with a standby MM.
| ||||
| SstandbyExtEthernetInterfaceDuplexSetting | 1.3.6.1.4.1.2.3.51.2.4.9.1.3.6 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Specifies the duplex settings for the data transfer rate to be used over the ethernet interface: Half, Full, or Auto. NOTE: This MIB object is only applicable to systems with a standby MM.
| ||||
| SstandbyExtEthernetInterfaceLAA | 1.3.6.1.4.1.2.3.51.2.4.9.1.3.7 | OCTET STRING (SIZE (17)) | RW | mandatory |
scalar · OCTET STRING (SIZE (17)) · read-write · mandatory Specifies the locally administered MAC address. The locally administered address must be a hexadecimal value between 000000000000 - FFFFFFFFFFFF. This value must be in the form XX:XX:XX:XX:XX:XX where 'X' is a number between 0 - 9 and A - F. This MM subsystem does not allow use of a multicast address. A multicast address has the least significant bit of the first byte set to a 1. The first byte must, therefore, be an even number. NOTE: This MIB object is only applicable to systems with a standby MM. NOTE: Although the locally administered MAC address can be assigned the same value for the primary and backup MM, it is not recommended. | ||||
| SstandbyExtEthernetInterfaceDhcpEnabled | 1.3.6.1.4.1.2.3.51.2.4.9.1.3.8 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Disable or enable DHCP on this interface. NOTE: This MIB object is only applicable to systems with a standby MM.
| ||||
| SstandbyExtEthernetInterfaceGatewayIPAddress | 1.3.6.1.4.1.2.3.51.2.4.9.1.3.9 | IpAddress | RW | mandatory |
scalar · IpAddress · read-write · mandatory Contains the IP address of the gateway/router for the ethernet interface. NOTE: This MIB object is only applicable to systems with a standby MM. | ||||
| SstandbyExtEthernetInterfaceBIA | 1.3.6.1.4.1.2.3.51.2.4.9.1.3.10 | OCTET STRING (SIZE (17)) | RO | mandatory |
scalar · OCTET STRING (SIZE (17)) · read-only · mandatory Specifies the burned-in MAC (BIA) address. NOTE: This MIB object is only applicable to systems with a standby MM. | ||||
| SstandbyExtEthernetInterfaceMTU | 1.3.6.1.4.1.2.3.51.2.4.9.1.3.13 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Contains the Maximum Transmission Unit (MTU) for the ethernet interface. NOTE: This MIB object is only applicable to systems with a standby MM. | ||||
| SstandbyExtEthernetInterfaceSubnetMask | 1.3.6.1.4.1.2.3.51.2.4.9.1.3.14 | IpAddress | RW | mandatory |
scalar · IpAddress · read-write · mandatory Contains the subnet mask for the ethernet interface. NOTE: This MIB object is only applicable to systems with a standby MM. | ||||
| SadvancedFailover | 1.3.6.1.4.1.2.3.51.2.4.9.1.3.15 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory User can enable advanced failover. off : no standby network interface ipswap: Standby network interface, swap IPs during failover ipnoswap: Standby network interface, do not swap IPs during failover. NOTE: This MIB object is only applicable to systems with a standby MM.
| ||||
| NstandbyDhcpEthernetInterface | 1.3.6.1.4.1.2.3.51.2.4.9.1.3.16 | |||
| SstandbyDhcpHostName | 1.3.6.1.4.1.2.3.51.2.4.9.1.3.16.1 | OCTET STRING (SIZE (0..64)) | RO | mandatory |
scalar · OCTET STRING (SIZE (0..64)) · read-only · mandatory Contains the 64 byte null terminated DNS host name for this interface, assigned by the DHCP server. NOTE: This MIB object is only applicable to systems with a standby MM. | ||||
| SstandbyDhcpIPAddress | 1.3.6.1.4.1.2.3.51.2.4.9.1.3.16.2 | IpAddress | RO | mandatory |
scalar · IpAddress · read-only · mandatory Contains the IP address for the ethernet interface, assigned by the DHCP server. NOTE: This MIB object is only applicable to systems with a standby MM. | ||||
| SstandbyDhcpGatewayIPAddress | 1.3.6.1.4.1.2.3.51.2.4.9.1.3.16.3 | IpAddress | RO | mandatory |
scalar · IpAddress · read-only · mandatory Contains the IP address of the gateway/router for the ethernet interface, assigned by the DHCP server. NOTE: This MIB object is only applicable to systems with a standby MM. | ||||
| SstandbyDhcpSubnetMask | 1.3.6.1.4.1.2.3.51.2.4.9.1.3.16.4 | IpAddress | RO | mandatory |
scalar · IpAddress · read-only · mandatory Contains the Subnet Mask for the ethernet interface, assigned by the DHCP server. NOTE: This MIB object is only applicable to systems with a standby MM. | ||||
| SstandbyDhcpDomainName | 1.3.6.1.4.1.2.3.51.2.4.9.1.3.16.5 | OCTET STRING (SIZE (0..64)) | RO | mandatory |
scalar · OCTET STRING (SIZE (0..64)) · read-only · mandatory Contains the 64 byte null terminated Domain Name for this interface, assigned by the DHCP server. NOTE: This MIB object is only applicable to systems with a standby MM. | ||||
| SstandbyDhcpDHCPServer | 1.3.6.1.4.1.2.3.51.2.4.9.1.3.16.6 | IpAddress | RO | mandatory |
scalar · IpAddress · read-only · mandatory Contains the DHCP server IP address used to acquire the DHCP settings. NOTE: This MIB object is only applicable to systems with a standby MM. | ||||
| SstandbyDhcpPrimaryDNSServer | 1.3.6.1.4.1.2.3.51.2.4.9.1.3.16.7 | IpAddress | RO | mandatory |
scalar · IpAddress · read-only · mandatory Contains the Primary DNS server, assigned by the DHCP server. NOTE: This MIB object is only applicable to systems with a standby MM. | ||||
| SstandbyDhcpSecondaryDNSServer | 1.3.6.1.4.1.2.3.51.2.4.9.1.3.16.8 | IpAddress | RO | mandatory |
scalar · IpAddress · read-only · mandatory Contains the Secondary DNS server, assigned by the DHCP server. NOTE: This MIB object is only applicable to systems with a standby MM. | ||||
| SstandbyDhcpTertiaryDNSServer | 1.3.6.1.4.1.2.3.51.2.4.9.1.3.16.9 | IpAddress | RO | mandatory |
scalar · IpAddress · read-only · mandatory Contains the tertiary DNS server, assigned by the DHCP server. NOTE: This MIB object is only applicable to systems with a standby MM. | ||||
| NextEthernetInterfaceIPv6 | 1.3.6.1.4.1.2.3.51.2.4.9.1.4 | |||
| SextEthernetInterfaceIPv6Type | 1.3.6.1.4.1.2.3.51.2.4.9.1.4.1 | OCTET STRING (SIZE (0..16)) | RO | mandatory |
scalar · OCTET STRING (SIZE (0..16)) · read-only · mandatory The type of interface. | ||||
| SextEthernetInterfaceIPv6Enabled | 1.3.6.1.4.1.2.3.51.2.4.9.1.4.2 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory The current IPv6 enabled or disabled state of this MM. NOTE: If IPv6 address(es) have been configured for one or more interfaces/protocols/services on this MM, when you update the firmware to a level which does not support IPv6, all IPv6 connectivity will be lost, and services/interfaces for which an IPv6 address was configured may not function properly. You will be required to reconfigure these services/interfaces.
| ||||
| NextEthernetInterfaceIPv6Config | 1.3.6.1.4.1.2.3.51.2.4.9.1.4.5 | |||
| NextEthernetInterfaceIPv6LocalAddress | 1.3.6.1.4.1.2.3.51.2.4.9.1.4.5.1 | |||
| SextEthernetInterfaceIPv6LinkLocalAddress | 1.3.6.1.4.1.2.3.51.2.4.9.1.4.5.1.1 | InetAddressIPv6 | RO | mandatory |
scalar · InetAddressIPv6 · read-only · mandatory The IPv6 link local IP address for the ethernet interface. NOTE: If extEthernetInterfaceIPv6Enabled is currently disabled, this object has the value '0:0:0:0:0:0:0:0'. | ||||
| NextEthernetInterfaceIPv6StaticIPConfig | 1.3.6.1.4.1.2.3.51.2.4.9.1.4.5.2 | |||
| SextEthernetInterfaceIPv6StaticIPConfigEnabled | 1.3.6.1.4.1.2.3.51.2.4.9.1.4.5.2.1 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory The IPv6 static IP address enabled or disabled state for the ethernet interface.
| ||||
| SextEthernetInterfaceIPv6StaticIPAddress | 1.3.6.1.4.1.2.3.51.2.4.9.1.4.5.2.2 | InetAddressIPv6 | RW | mandatory |
scalar · InetAddressIPv6 · read-write · mandatory The IPv6 static IP address for the ethernet interface. NOTE: If extEthernetInterfaceIPv6Enabled is currently disabled, this object has the value '0:0:0:0:0:0:0:0'. | ||||
| SextEthernetInterfaceIPv6StaticIPAddressPrefixLen | 1.3.6.1.4.1.2.3.51.2.4.9.1.4.5.2.3 | INTEGER (1..128) | RW | mandatory |
scalar · INTEGER (1..128) · read-write · mandatory The IPv6 static IP address prefix length for the ethernet interface. NOTE: If extEthernetInterfaceIPv6Enabled is currently disabled, this object has the value 0. | ||||
| SextEthernetInterfaceIPv6StaticIPDefaultRoute | 1.3.6.1.4.1.2.3.51.2.4.9.1.4.5.2.4 | InetAddressIPv6 | RW | mandatory |
scalar · InetAddressIPv6 · read-write · mandatory The IPv6 static IP address default route for the ethernet interface. NOTE: If extEthernetInterfaceIPv6Enabled is currently disabled, this object has the value '0:0:0:0:0:0:0:0'. | ||||
| SextEthernetInterfaceIPv6LinkFloatingAddress | 1.3.6.1.4.1.2.3.51.2.4.9.1.4.5.2.5 | InetAddressIPv6 | RW | mandatory |
scalar · InetAddressIPv6 · read-write · mandatory The IPv6 floating IP address for the external ethernet interface. NOTE: If extEthernetInterfaceIPv6Enabled is currently disabled, this object has the value '0:0:0:0:0:0:0:0'. | ||||
| NextEthernetInterfaceIPv6AutoIPConfig | 1.3.6.1.4.1.2.3.51.2.4.9.1.4.5.3 | |||
| SextEthernetInterfaceIPv6AutoIPConfigEnabled | 1.3.6.1.4.1.2.3.51.2.4.9.1.4.5.3.1 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory The IPv6 automatic IP configuration enabled or disabled state for the ethernet interface. NOTE: extEthernetInterfaceIPv6AutoIPConfigEnabled is the logical OR of extEthernetInterfaceDHCPv6Enabled and extEthernetInterfaceIPv6StatelessAutoConfigEnabled settings. NOTE: Enabling/Disabling extEthernetInterfaceIPv6AutoIPConfigEnabled will cause both extEthernetInterfaceDHCPv6Enabled and extEthernetInterfaceIPv6StatelessAutoConfigEnabled to be enabled/disabled. NOTE: extEthernetInterfaceIPv6StaticIPConfigEnabled and extEthernetInterfaceIPv6AutoIPConfigEnabled cannot be disabled at the same time.
| ||||
| NextEthernetInterfaceDHCPv6Config | 1.3.6.1.4.1.2.3.51.2.4.9.1.4.5.3.2 | |||
| SextEthernetInterfaceDHCPv6Enabled | 1.3.6.1.4.1.2.3.51.2.4.9.1.4.5.3.2.1 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory The DHCPv6 enabled or disabled state for the ethernet interface. NOTE: If extEthernetInterfaceIPv6StatelessAutoConfigEnabled is currently disabled, Disabling extEthernetInterfaceDHCPv6Enabled will cause extEthernetInterfaceIPv6AutoIPConfigEnabled to be disabled. NOTE: If extEthernetInterfaceIPv6StaticIPConfigEnabled and extEthernetInterfaceIPv6StatelessAutoConfigEnabled are currently disabled, Disabling extEthernetInterfaceDHCPv6Enabled will not be allowed.
| ||||
| SextEthernetInterfaceDHCPv6IPAddress | 1.3.6.1.4.1.2.3.51.2.4.9.1.4.5.3.2.2 | InetAddressIPv6 | RO | mandatory |
scalar · InetAddressIPv6 · read-only · mandatory The IPv6 address for the ethernet interface, assigned by DHCPv6 server. NOTE: If extEthernetInterfaceIPv6Enabled or extEthernetInterfaceDHCPv6Enabled is disabled or if DHCPv6 server is not available, this object has the value '0:0:0:0:0:0:0:0'. | ||||
| SextEthernetInterfaceDHCPv6DomainName | 1.3.6.1.4.1.2.3.51.2.4.9.1.4.5.3.2.4 | OCTET STRING (SIZE (0..64)) | RO | mandatory |
scalar · OCTET STRING (SIZE (0..64)) · read-only · mandatory The 64 byte Domain Name for the ethernet interface, assigned by the DHCPv6 server. NOTE: If extEthernetInterfaceIPv6Enabled or extEthernetInterfaceDHCPv6Enabled is disabled or if DHCPv6 server is not available, this object has the value '(Not available)'. | ||||
| SextEthernetInterfaceDHCPv6PrimaryDNSServer | 1.3.6.1.4.1.2.3.51.2.4.9.1.4.5.3.2.5 | InetAddressIPv6 | RO | mandatory |
scalar · InetAddressIPv6 · read-only · mandatory The primary DNS server, assigned by the DHCPv6 server. NOTE: If extEthernetInterfaceIPv6Enabled or extEthernetInterfaceDHCPv6Enabled is disabled or if DHCPv6 server is not available, this object has the value '0:0:0:0:0:0:0:0'. | ||||
| SextEthernetInterfaceDHCPv6SecondaryDNSServer | 1.3.6.1.4.1.2.3.51.2.4.9.1.4.5.3.2.6 | InetAddressIPv6 | RO | mandatory |
scalar · InetAddressIPv6 · read-only · mandatory The secondary DNS server, assigned by the DHCPv6 server. NOTE: If extEthernetInterfaceIPv6Enabled or extEthernetInterfaceDHCPv6Enabled is disabled or if DHCPv6 server is not available, this object has the value '0:0:0:0:0:0:0:0'. | ||||
| SextEthernetInterfaceDHCPv6TertiaryDNSServer | 1.3.6.1.4.1.2.3.51.2.4.9.1.4.5.3.2.7 | InetAddressIPv6 | RO | mandatory |
scalar · InetAddressIPv6 · read-only · mandatory The tertiary DNS server, assigned by the DHCPv6 server. NOTE: If extEthernetInterfaceIPv6Enabled or extEthernetInterfaceDHCPv6Enabled is disabled or if DHCPv6 server is not available, this object has the value '0:0:0:0:0:0:0:0'. | ||||
| SextEthernetInterfaceDHCPv6Server | 1.3.6.1.4.1.2.3.51.2.4.9.1.4.5.3.2.8 | InetAddressIPv6 | RO | mandatory |
scalar · InetAddressIPv6 · read-only · mandatory The DHCPv6 server IPv6 address used to acquire the DHCP settings. NOTE: If extEthernetInterfaceIPv6Enabled or extEthernetInterfaceDHCPv6Enabled is disabled or if DHCPv6 server is not available, this object has the value '0:0:0:0:0:0:0:0'. | ||||
| NextEthernetInterfaceIPv6StatelessAutoConfig | 1.3.6.1.4.1.2.3.51.2.4.9.1.4.5.3.3 | |||
| SextEthernetInterfaceIPv6StatelessAutoConfigEnabled | 1.3.6.1.4.1.2.3.51.2.4.9.1.4.5.3.3.1 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory The IPv6 stateless auto-configuration enabled or disabled state for the ethernet interface. NOTE: If extEthernetfInterfaceDHCPv6Enabled is currently disabled, Disabling extEthernetInterfaceIPv6StatelessAutoConfigEnabled will cause extEthernetInterfaceIPv6AutoIPConfigEnabled to be disabled.
| ||||
| TextEthernetInterfaceStatelessAutoConfigAddressesTable | 1.3.6.1.4.1.2.3.51.2.4.9.1.4.5.3.3.2 | NA | mandatory | |
table · not-accessible · mandatory Table of stateless Auto-Config addresses entries | ||||
| RextEthernetInterfaceStatelessAutoConfigAddressesEntry | 1.3.6.1.4.1.2.3.51.2.4.9.1.4.5.3.3.2.1 | NA | mandatory | |
row · not-accessible · mandatory Stateless Auto-Config address entries | ||||
| CextEthernetInterfaceStatelessAutoConfigAddressesIndex | 1.3.6.1.4.1.2.3.51.2.4.9.1.4.5.3.3.2.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Index for stateless Auto-Config addresses. NOTE: If extEthernetInterfaceIPv6StatelessAutoConfigEnabled or extEthernetInterfaceIPv6Enabled is currently disabled, this object will show nothing. | ||||
| CextEthernetInterfaceStatelessAutoConfigAddresses | 1.3.6.1.4.1.2.3.51.2.4.9.1.4.5.3.3.2.1.2 | InetAddressIPv6 | RO | mandatory |
column · InetAddressIPv6 · read-only · mandatory The stateless Auto-Configuration IPv6 address. NOTE: If extEthernetInterfaceIPv6StatelessAutoConfigEnabled or extEthernetInterfaceIPv6Enabled is currently disabled, this object will show nothing. | ||||
| CextEthernetInterfaceStatelessAutoConfigAddressesPrefixLen | 1.3.6.1.4.1.2.3.51.2.4.9.1.4.5.3.3.2.1.3 | INTEGER (1..128) | RO | mandatory |
column · INTEGER (1..128) · read-only · mandatory The stateless Auto-Configration address prefix length. NOTE: If extEthernetInterfaceIPv6StatelessAutoConfigEnabled or extEthernetInterfaceIPv6Enabled is currently disabled, this object will show nothing. | ||||
| NstandbyExtEthernetInterfaceIPv6 | 1.3.6.1.4.1.2.3.51.2.4.9.1.5 | |||
| NstandbyEthernetInterfaceIPv6LocalAddress | 1.3.6.1.4.1.2.3.51.2.4.9.1.5.1 | |||
| SstandbyEthernetInterfaceIPv6LinkLocalAddress | 1.3.6.1.4.1.2.3.51.2.4.9.1.5.1.1 | InetAddressIPv6 | RO | mandatory |
scalar · InetAddressIPv6 · read-only · mandatory The IPv6 link local IP address for the standby MM. | ||||
| NstandbyEthernetInterfaceIPv6StaticIPConfig | 1.3.6.1.4.1.2.3.51.2.4.9.1.5.2 | |||
| SstandbyEthernetInterfaceIPv6StaticIPConfigEnabled | 1.3.6.1.4.1.2.3.51.2.4.9.1.5.2.1 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory The IPv6 static IP address state for the MM. NOTE: This value may be altered through the extEthernetInterfaceIPv6StaticIPConfigEnabled object.
| ||||
| SstandbyEthernetInterfaceIPv6StaticIPAddress | 1.3.6.1.4.1.2.3.51.2.4.9.1.5.2.2 | InetAddressIPv6 | RW | mandatory |
scalar · InetAddressIPv6 · read-write · mandatory The IPv6 static IP address for the standby MM NOTE: If extEthernetInterfaceIPv6Enabled is currently disabled, this object has the value '0:0:0:0:0:0:0:0'. | ||||
| SstandbyEthernetInterfaceIPv6StaticIPAddressPrefixLen | 1.3.6.1.4.1.2.3.51.2.4.9.1.5.2.3 | INTEGER (1..128) | RO | mandatory |
scalar · INTEGER (1..128) · read-only · mandatory The IPv6 static IP address prefix length for the standyby MM. NOTE: This value may be altered through the extEthernetInterfaceIPv6StaticIPAddressPrefixLen object. | ||||
| SstandbyEthernetInterfaceIPv6StaticIPDefaultRoute | 1.3.6.1.4.1.2.3.51.2.4.9.1.5.2.4 | InetAddressIPv6 | RO | mandatory |
scalar · InetAddressIPv6 · read-only · mandatory The IPv6 static IP address default route for the standby MM. NOTE: This value may be altered through the extEthernetInterfaceIPv6StaticIPDefaultRoute object. | ||||
| NstandbyEthernetInterfaceDHCPv6Config | 1.3.6.1.4.1.2.3.51.2.4.9.1.5.3 | |||
| SstandbyEthernetInterfaceDHCPv6Enabled | 1.3.6.1.4.1.2.3.51.2.4.9.1.5.3.1 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory The DHCPv6 enabled or disabled state for the standby MM. NOTE: This field may be altered through the extEthernetInterfaceDHCPv6Enabled object.
| ||||
| SstandbyEthernetInterfaceDHCPv6IPAddress | 1.3.6.1.4.1.2.3.51.2.4.9.1.5.3.2 | InetAddressIPv6 | RO | mandatory |
scalar · InetAddressIPv6 · read-only · mandatory The IPv6 address for the standby MM assigned by DHCPv6 server. | ||||
| SstandbyEthernetInterfaceDHCPv6DomainName | 1.3.6.1.4.1.2.3.51.2.4.9.1.5.3.4 | OCTET STRING (SIZE (0..64)) | RO | mandatory |
scalar · OCTET STRING (SIZE (0..64)) · read-only · mandatory The 64 byte Domain Name for the standby MM assigned by the DHCPv6 server. | ||||
| TstandbyEthernetInterfaceStatelessAutoConfigAddressesTable | 1.3.6.1.4.1.2.3.51.2.4.9.1.5.4 | NA | mandatory | |
table · not-accessible · mandatory Table of stateless Auto-Config addresses entries. NOTE: If extEthernetInterfaceIPv6StatelessAutoConfigEnabled or extEthernetInterfaceIPv6Enabled is currently disabled, this table will show nothing. | ||||
| RstandbyEthernetInterfaceStatelessAutoConfigAddressesEntry | 1.3.6.1.4.1.2.3.51.2.4.9.1.5.4.1 | NA | mandatory | |
row · not-accessible · mandatory Stateless Auto-Config address entries | ||||
| CstandbyEthernetInterfaceStatelessAutoConfigAddressesIndex | 1.3.6.1.4.1.2.3.51.2.4.9.1.5.4.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Index for stateless Auto-Config addresses. | ||||
| CstandbyEthernetInterfaceStatelessAutoConfigAddresses | 1.3.6.1.4.1.2.3.51.2.4.9.1.5.4.1.2 | InetAddressIPv6 | RO | mandatory |
column · InetAddressIPv6 · read-only · mandatory The stateless Auto-Configuration IPv6 address. | ||||
| CstandbyEthernetInterfaceStatelessAutoConfigAddressesPrefixLen | 1.3.6.1.4.1.2.3.51.2.4.9.1.5.4.1.3 | INTEGER (1..128) | RO | mandatory |
column · INTEGER (1..128) · read-only · mandatory The stateless Auto-Configration address prefix length. | ||||
| SddnsStatus | 1.3.6.1.4.1.2.3.51.2.4.9.1.10 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Dynamic DNS provides the capability for a networked device to notify a domain name server to change, in real time, the active DNS configuration of its configured hostnames, addresses or other information stored in DNS. With Dynamic DNS, host computers gain the capability to notify their respective DNS server of the IP address they have received from a DHCP server or through self-configuration.
| ||||
| ShostName | 1.3.6.1.4.1.2.3.51.2.4.9.1.11 | OCTET STRING (SIZE (0..64)) | RW | mandatory |
scalar · OCTET STRING (SIZE (0..64)) · read-write · mandatory Contains the DNS host name for this system. This object provides the exact same function as extEthernetInterfaceHostName | ||||
| SstandbyHostName | 1.3.6.1.4.1.2.3.51.2.4.9.1.12 | OCTET STRING (SIZE (0..64)) | RW | mandatory |
scalar · OCTET STRING (SIZE (0..64)) · read-write · mandatory Contains the DNS host name for the standby. This object provides the exact same function as standbyExtEthernetInterfaceHostName and is only applicable to systems with a standby MM. | ||||
| SdomainName | 1.3.6.1.4.1.2.3.51.2.4.9.1.13 | OCTET STRING | RW | mandatory |
scalar · OCTET STRING · read-write · mandatory The user assigned DNS domain name. | ||||
| SstandbyDomainName | 1.3.6.1.4.1.2.3.51.2.4.9.1.14 | OCTET STRING | RW | mandatory |
scalar · OCTET STRING · read-write · mandatory The user assigned DNS domain name of the standby. This is only applicable to systems with a standby MM. | ||||
| SactivateNetworkUpdates | 1.3.6.1.4.1.2.3.51.2.4.9.1.16 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory When read, the return value indicates if there are any pending network updates ready to be applied. Writing any value will apply any pending network updates immediately.
| ||||
| NvlanConfigure | 1.3.6.1.4.1.2.3.51.2.4.9.1.20 | |||
| SvlanGlobalState | 1.3.6.1.4.1.2.3.51.2.4.9.1.20.1 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory This object disables or enables the VLAN feature. The configuration objects for the VLAN are in the vlanCMMTable. The default setting for this object is disable(0). IMPORTANT NOTE: Any change to this object will revert back to its previous value if the change is not committed by setting the object vlanCommitState to executeCommit(3) within the number of minutes indicated in the object vlanCommitTimeout.
| ||||
| SvlanCommitTimeout | 1.3.6.1.4.1.2.3.51.2.4.9.1.20.2 | INTEGER (1..255) | RW | mandatory |
scalar · INTEGER (1..255) · read-write · mandatory This object is the number of minutes from the last VLAN-related object change until any non-committed changes will revert back to their previous settings. This means if a user makes a change that disrupts TCP/IP access to the CMM, the change will revert back to its previous setting after the number of minutes in this object. This allows the user to access the CMM again if access is lost through an unintended VLAN setting. Once the changes are committed using the object, vlanCommitState, setting it to executeCommit(3), the changes will be saved in non-volatile memory. The amount of time before uncommitted changes revert back to their previous settings starts from the last change made to any VLAN-related object. If no other change is made, the user has this number of minutes (the number in this object) to commit the changes with vlanCommitState before the changes will revert back. The default setting for this object is 2 minutes. IMPORTANT NOTE: Any change to this object will revert back to its previous value if the change is not committed by setting the object vlanCommitState to executeCommit(3) within the number of minutes indicated in the object vlanCommitTimeout. | ||||
| SvlanCommitState | 1.3.6.1.4.1.2.3.51.2.4.9.1.20.3 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory This object gives the status of whether there are VLAN-related changes pending that need to be committed, and allows a user to commit (save) any VLAN changes. If changes are pending, reading this object will give a value of commitNeeded(2). If no changes are pending, this object will have the value of noChangesPending(1). To save any VLAN-related changes so they do not revert back to previous settings, set this object to executeCommit(3) whenever this object has a value of commitNeeded(2).
| ||||
| TvlanCMMTable | 1.3.6.1.4.1.2.3.51.2.4.9.1.20.20 | NA | mandatory | |
table · not-accessible · mandatory This table contains the VLAN configuration objects. The default entry has an vlanCMMIndex equal to 1. The objects for this default entry are configurable. An additional VLAN entry may be added by setting the object, vlanCMMEntryStatus, at vlanCMMIndex=2 to the value of createRequest(2) and also setting the object, vlanCMMVlanId, at vlanCMMIndex=2 to a valid, unique value. IMPORTANT NOTE: Any changes to the object of this table will revert back to their previous settings if the changes are not committed by setting the object vlanCommitState to executeCommit(3) within the number of minutes indicated in the object vlanCommitTimeout. | ||||
| RvlanCMMEntry | 1.3.6.1.4.1.2.3.51.2.4.9.1.20.20.1 | NA | mandatory | |
| CvlanCMMIndex | 1.3.6.1.4.1.2.3.51.2.4.9.1.20.20.1.1 | INTEGER (1..2) | RO | mandatory |
column · INTEGER (1..2) · read-only · mandatory Index for VLAN entry. If vlanCMMIndex is equal to 1, it is the Default VLAN entry and cannot be deleted. | ||||
| CvlanCMMVlanId | 1.3.6.1.4.1.2.3.51.2.4.9.1.20.20.1.2 | INTEGER (1..4094) | RW | mandatory |
column · INTEGER (1..4094) · read-write · mandatory Valid VLAN ID. Allowed values are 5..4094. If the entry is not valid, this object will have the value of 0. If this entry has the vlanCMMIndex value of 1 (default VLAN entry), then setting this object will take effect immediately. For other entries, when this object is set, this entry must have the object, vlanCMMState set to enable(1) or restart(2) for this change to take effect. | ||||
| CvlanCMMName | 1.3.6.1.4.1.2.3.51.2.4.9.1.20.20.1.3 | OCTET STRING (SIZE (0..31)) | RW | mandatory |
column · OCTET STRING (SIZE (0..31)) · read-write · mandatory This object allows the user to configure a text string name for this VLAN entry. This entry name is only used as a label for this entry. | ||||
| CvlanCMMEntryStatus | 1.3.6.1.4.1.2.3.51.2.4.9.1.20.20.1.4 | EntryStatus | RW | mandatory |
column · EntryStatus · read-write · mandatory This object manages the creation and deletion of this
entry.
The steps recommended to add a new VLAN entry are:
1. Create a new entry in this table
vlanCMMEntryStatus = createRequest
2. Set vlanCMMVlanId as required.
Then the entry will be valid.
valid(1) - Indicates that this entry is available
for use.
createRequest(2) - A new entry will be created in this
table and will transition to the
vlanCMMEntryStatus value of
underCreation(3).
underCreation(3) - Indicates that this entry exists in the
agent but is unavailable for use. After
completing the create operation, the
agent will set this object to the value
underCreation(3).
invalid(4) - Deletes this entry.
The entry with the vlanCMMIndex value of 1 (default VLAN
entry) cannot be deleted. | ||||
| CvlanCMMState | 1.3.6.1.4.1.2.3.51.2.4.9.1.20.20.1.5 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory This object indicates whether this VLAN entry is enabled or disabled and allows the user to disable, enable or restart this entry except for the exceptions noted below. The entry with a vlanCMMIndex value of 1 (default VLAN entry) will always have this object set to enable(1) and cannot be set to any other value. Other table entries do not have this restriction. Some other objects in this table may not take effect after a change until either this object is: set to enable(1) if this object currently has the value of disable(0), or set to restart(2) if this object currently has the value of enable(1). The other objects in this table that require this object be set to enable(1) or restart(2) after a change are noted in the description for those objects.
| ||||
| CvlanCMMSOLAccess | 1.3.6.1.4.1.2.3.51.2.4.9.1.20.20.1.6 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory This object allows the user to set whether the VLAN for this entry will have access to the Serial Over LAN (SOL) interface. Only one VLAN entry may have this object set to enable(1). By default, the entry with the vlanCMMIndex value of 1 (default VLAN entry) will have this object set to enable(1). To set this object to enable(1) on another entry, this object must first be set to disable(0) on any entry that has this object set to enable(1).
| ||||
| CvlanCMMTagging | 1.3.6.1.4.1.2.3.51.2.4.9.1.20.20.1.8 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory This object allows the user to set whether VLAN tagging is enabled for this VLAN entry. This object is only configurable for the entry with the vlanCMMIndex value of 1. By default, the entry with the vlanCMMIndex value of 1 (default VLAN entry) will have this object set to disable(0), all other entries will have this object set to enable(1).
| ||||
| CvlanCMMIPv4Address | 1.3.6.1.4.1.2.3.51.2.4.9.1.20.20.1.31 | IpAddress | RW | mandatory |
column · IpAddress · read-write · mandatory This object sets the IPv4 address for this VLAN entry. The entry with the vlanCMMIndex value of 1 (default VLAN entry) will have this object set to the IP address of the ethernet interface. The IP address of the default VLAN entry can only change by changing the IP address of the ethernet interface. For all other VLAN entries, this object may be set to any IP address except the IP address of the ethernet interface. For a change of this object to take effect, the object, vlanCMMState, must be set to enable(1) if the vlanCMMState is currently disable(0), or set to restart(2) if the vlanCMMState is currently enable(1). | ||||
| CvlanCMMIPv4Gateway | 1.3.6.1.4.1.2.3.51.2.4.9.1.20.20.1.32 | IpAddress | RW | mandatory |
column · IpAddress · read-write · mandatory This object sets the IPv4 address for the IP gateway for this VLAN entry. The entry with the vlanCMMIndex value of 1 (default VLAN entry) will have this object set to the IP gateway for the ethernet interface. The IP address of the default VLAN entry can only change by changing the IP gateway of the ethernet interface. For all other VLAN entries, this object may be set to any IP address except the IP address of the ethernet interface. For a change of this object to take effect, the object, vlanCMMState, must be set to enable(1) if the vlanCMMState is currently disable(0), or set to restart(2) if the vlanCMMState is currently enable(1). | ||||
| CvlanCMMIPv4Mask | 1.3.6.1.4.1.2.3.51.2.4.9.1.20.20.1.33 | IpAddress | RW | mandatory |
column · IpAddress · read-write · mandatory This object sets the IPv4 subnet mask for this VLAN entry. The entry with the vlanCMMIndex value of 1 (default VLAN entry) will have this object set to the subnet mask of the ethernet interface. The subnet mask of the default VLAN entry can only change by changing the subnet mask of the ethernet interface. For all other VLAN entries, this object may be set to any valid subnet mask. For a change of this object to take effect, the object, vlanCMMState, must be set to enable(1) if the vlanCMMState is currently disable(0), or set to restart(2) if the vlanCMMState is currently enable(1). | ||||
| CvlanCMMIPv4SubnetRoute1 | 1.3.6.1.4.1.2.3.51.2.4.9.1.20.20.1.51 | IpAddress | RW | mandatory |
column · IpAddress · read-write · mandatory This object sets the IPv4 address of the subnet route 1 for this VLAN entry. The entry with the vlanCMMIndex value of 1 (default VLAN entry) will always have this object set to 0.0.0.0. For all other VLAN entries, this object may be set to any valid subnet route. For a change of this object to take effect, the object, vlanCMMState, must be set to enable(1) if the vlanCMMState is currently disable(0), or set to restart(2) if the vlanCMMState is currently enable(1). | ||||
| CvlanCMMIPv4SubnetRouteMask1 | 1.3.6.1.4.1.2.3.51.2.4.9.1.20.20.1.52 | IpAddress | RW | mandatory |
column · IpAddress · read-write · mandatory This object sets the IPv4 subnet route mask 1 for this VLAN entry. The entry with the vlanCMMIndex value of 1 (default VLAN entry) will always have this object set to 0.0.0.0. For all other VLAN entries, this object may be set to any valid subnet mask. For a change of this object to take effect, the object, vlanCMMState, must be set to enable(1) if the vlanCMMState is currently disable(0), or set to restart(2) if the vlanCMMState is currently enable(1). | ||||
| CvlanCMMIPv4SubnetRoute2 | 1.3.6.1.4.1.2.3.51.2.4.9.1.20.20.1.53 | IpAddress | RW | mandatory |
column · IpAddress · read-write · mandatory This object sets the IPv4 address of the subnet route 2 for VLAN entry. The entry with the vlanCMMIndex value of 1 (default VLAN entry) will always have this object set to 0.0.0.0. For all other VLAN entries, this object may be set to any valid subnet route. For a change of this object to take effect, the object, vlanCMMState, must be set to enable(1) if the vlanCMMState is currently disable(0), or set to restart(2) if the vlanCMMState is currently enable(1). | ||||
| CvlanCMMIPv4SubnetRouteMask2 | 1.3.6.1.4.1.2.3.51.2.4.9.1.20.20.1.54 | IpAddress | RW | mandatory |
column · IpAddress · read-write · mandatory This object sets the IPv4 subnet route mask 2 for this VLAN entry. The entry with the vlanCMMIndex value of 1 (default VLAN entry) will always have this object set to 0.0.0.0. For all other VLAN entries, this object may be set to any valid subnet mask. For a change of this object to take effect, the object, vlanCMMState, must be set to enable(1) if the vlanCMMState is currently disable(0), or set to restart(2) if the vlanCMMState is currently enable(1). | ||||
| CvlanCMMIPv4SubnetRoute3 | 1.3.6.1.4.1.2.3.51.2.4.9.1.20.20.1.55 | IpAddress | RW | mandatory |
column · IpAddress · read-write · mandatory This object sets the IPv4 address of the subnet route 3 for this VLAN entry. The entry with the vlanCMMIndex value of 1 (default VLAN entry) will always have this object set to 0.0.0.0. For all other VLAN entries, this object may be set to any valid subnet route. For a change of this object to take effect, the object, vlanCMMState, must be set to enable(1) if the vlanCMMState is currently disable(0), or set to restart(2) if the vlanCMMState is currently enable(1). | ||||
| CvlanCMMIPv4SubnetRouteMask3 | 1.3.6.1.4.1.2.3.51.2.4.9.1.20.20.1.56 | IpAddress | RW | mandatory |
column · IpAddress · read-write · mandatory This object sets the IPv4 subnet route mask 3 for this VLAN entry. The entry with the vlanCMMIndex value of 1 (default VLAN entry) will always have this object set to 0.0.0.0. For all other VLAN entries, this object may be set to any valid subnet mask. For a change of this object to take effect, the object, vlanCMMState, must be set to enable(1) if the vlanCMMState is currently disable(0), or set to restart(2) if the vlanCMMState is currently enable(1). | ||||
| CvlanCMMIPv6Address | 1.3.6.1.4.1.2.3.51.2.4.9.1.20.20.1.71 | InetAddressIPv6 | RW | mandatory |
column · InetAddressIPv6 · read-write · mandatory This object sets the IPv6 address for this VLAN entry. The entry with the vlanCMMIndex value of 1 (default VLAN entry) will have this object set to the IP address of the ethernet interface. The IP address of the default VLAN entry can only change by changing the IP address of the ethernet interface. For all other VLAN entries, this object may be set to any IP address except the IP address of the ethernet interface. For a change of this object to take effect, the object, vlanCMMState, must be set to enable(1) if the vlanCMMState is currently disable(0), or set to restart(2) if the vlanCMMState is currently enable(1). | ||||
| CvlanCMMIPv6AddressPrefixLen | 1.3.6.1.4.1.2.3.51.2.4.9.1.20.20.1.72 | INTEGER (0..128) | RW | mandatory |
column · INTEGER (0..128) · read-write · mandatory This object sets the IPv6 address prefix length for this VLAN entry. The entry with the vlanCMMIndex value of 1 (default VLAN entry) will have this object set to the IP address of the ethernet interface. The IP address of the default VLAN entry can only change by changing the IP address of the ethernet interface. For all other VLAN entries, this object may be set to any IP address except the IP address of the ethernet interface. For a change of this object to take effect, the object, vlanCMMState, must be set to enable(1) if the vlanCMMState is currently disable(0), or set to restart(2) if the vlanCMMState is currently enable(1). | ||||
| CvlanCMMIPv6Gateway | 1.3.6.1.4.1.2.3.51.2.4.9.1.20.20.1.73 | InetAddressIPv6 | RW | mandatory |
column · InetAddressIPv6 · read-write · mandatory This object sets the IPv6 address for the IP gateway for this VLAN entry. The entry with the vlanCMMIndex value of 1 (default VLAN entry) will have this object set to the IP gateway for the ethernet interface. The IP address of the default VLAN entry can only change by changing the IP gateway of the ethernet interface. For all other VLAN entries, this object may be set to any IP address except the IP address of the ethernet interface. For a change of this object to take effect, the object, vlanCMMState, must be set to enable(1) if the vlanCMMState is currently disable(0), or set to restart(2) if the vlanCMMState is currently enable(1). | ||||
| CvlanCMMIPv6SubnetRoute1 | 1.3.6.1.4.1.2.3.51.2.4.9.1.20.20.1.91 | InetAddressIPv6 | RW | mandatory |
column · InetAddressIPv6 · read-write · mandatory This object sets the IPv6 address of the subnet route 1 for this VLAN entry. The entry with the vlanCMMIndex value of 1 (default VLAN entry) will always have this object set to 0.0.0.0. For all other VLAN entries, this object may be set to any valid subnet route. For a change of this object to take effect, the object, vlanCMMState, must be set to enable(1) if the vlanCMMState is currently disable(0), or set to restart(2) if the vlanCMMState is currently enable(1). | ||||
| CvlanCMMIPv6SubnetRoutePrefixLen1 | 1.3.6.1.4.1.2.3.51.2.4.9.1.20.20.1.92 | INTEGER (0..128) | RW | mandatory |
column · INTEGER (0..128) · read-write · mandatory This object sets the IPv6 address prefix length of the subnet route 1 for this VLAN entry. The entry with the vlanCMMIndex value of 1 (default VLAN entry) will have this object set to the IP address of the ethernet interface. The IP address of the default VLAN entry can only change by changing the IP address of the ethernet interface. For all other VLAN entries, this object may be set to any IP address except the IP address of the ethernet interface. For a change of this object to take effect, the object, vlanCMMState, must be set to enable(1) if the vlanCMMState is currently disable(0), or set to restart(2) if the vlanCMMState is currently enable(1). | ||||
| CvlanCMMIPv6SubnetRoute2 | 1.3.6.1.4.1.2.3.51.2.4.9.1.20.20.1.93 | InetAddressIPv6 | RW | mandatory |
column · InetAddressIPv6 · read-write · mandatory This object sets the IPv6 address of the subnet route 2 for this VLAN entry. The entry with the vlanCMMIndex value of 1 (default VLAN entry) will always have this object set to 0.0.0.0. For all other VLAN entries, this object may be set to any valid subnet route. For a change of this object to take effect, the object, vlanCMMState, must be set to enable(1) if the vlanCMMState is currently disable(0), or set to restart(2) if the vlanCMMState is currently enable(1). | ||||
| CvlanCMMIPv6SubnetRoutePrefixLen2 | 1.3.6.1.4.1.2.3.51.2.4.9.1.20.20.1.94 | INTEGER (0..128) | RW | mandatory |
column · INTEGER (0..128) · read-write · mandatory This object sets the IPv6 address prefix length of the subnet route 2 for this VLAN entry. The entry with the vlanCMMIndex value of 1 (default VLAN entry) will have this object set to the IP address of the ethernet interface. The IP address of the default VLAN entry can only change by changing the IP address of the ethernet interface. For all other VLAN entries, this object may be set to any IP address except the IP address of the ethernet interface. For a change of this object to take effect, the object, vlanCMMState, must be set to enable(1) if the vlanCMMState is currently disable(0), or set to restart(2) if the vlanCMMState is currently enable(1). | ||||
| CvlanCMMIPv6SubnetRoute3 | 1.3.6.1.4.1.2.3.51.2.4.9.1.20.20.1.95 | InetAddressIPv6 | RW | mandatory |
column · InetAddressIPv6 · read-write · mandatory This object sets the IPv6 address of the subnet route 3 for this VLAN entry. The entry with the vlanCMMIndex value of 1 (default VLAN entry) will always have this object set to 0.0.0.0. For all other VLAN entries, this object may be set to any valid subnet route. For a change of this object to take effect, the object, vlanCMMState, must be set to enable(1) if the vlanCMMState is currently disable(0), or set to restart(2) if the vlanCMMState is currently enable(1). | ||||
| CvlanCMMIPv6SubnetRoutePrefixLen3 | 1.3.6.1.4.1.2.3.51.2.4.9.1.20.20.1.96 | INTEGER (0..128) | RW | mandatory |
column · INTEGER (0..128) · read-write · mandatory This object sets the IPv6 address prefix length of the subnet route 3 for this VLAN entry. The entry with the vlanCMMIndex value of 1 (default VLAN entry) will have this object set to the IP address of the ethernet interface. The IP address of the default VLAN entry can only change by changing the IP address of the ethernet interface. For all other VLAN entries, this object may be set to any IP address except the IP address of the ethernet interface. For a change of this object to take effect, the object, vlanCMMState, must be set to enable(1) if the vlanCMMState is currently disable(0), or set to restart(2) if the vlanCMMState is currently enable(1). | ||||
| SvlanCMMTableCacheTimeout | 1.3.6.1.4.1.2.3.51.2.4.9.1.20.21 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory The timeout value (in seconds) of the cached data for the table, vlanCMMTable. This value is static (constant) and cannot be set. | ||||
| NtcpProtocols | 1.3.6.1.4.1.2.3.51.2.4.9.3 | |||
| NsnmpAgentConfig | 1.3.6.1.4.1.2.3.51.2.4.9.3.1 | |||
| SsnmpSystemContact | 1.3.6.1.4.1.2.3.51.2.4.9.3.1.1 | OCTET STRING (SIZE (0..48)) | RW | mandatory |
scalar · OCTET STRING (SIZE (0..48)) · read-write · mandatory A NULL terminated 48 byte string that contains the SNMP agent contact name. | ||||
| SsnmpSystemLocation | 1.3.6.1.4.1.2.3.51.2.4.9.3.1.2 | OCTET STRING (SIZE (0..48)) | RW | mandatory |
scalar · OCTET STRING (SIZE (0..48)) · read-write · mandatory A NULL terminated 48 byte string that contains the SNMP agent location name. | ||||
| SsnmpSystemAgentTrapsDisable | 1.3.6.1.4.1.2.3.51.2.4.9.3.1.3 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Disable or enable SNMP traps.
| ||||
| NsnmpAgentCommunityConfig | 1.3.6.1.4.1.2.3.51.2.4.9.3.1.4 | |||
| TsnmpCommunityTable | 1.3.6.1.4.1.2.3.51.2.4.9.3.1.4.1 | NA | mandatory | |
table · not-accessible · mandatory Table of SNMP Community entries | ||||
| RsnmpCommunityEntry | 1.3.6.1.4.1.2.3.51.2.4.9.3.1.4.1.1 | NA | mandatory | |
| CsnmpCommunityEntryIndex | 1.3.6.1.4.1.2.3.51.2.4.9.3.1.4.1.1.1 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Index for SNMP Agent Community entry. | ||||
| CsnmpCommunityEntryCommunityName | 1.3.6.1.4.1.2.3.51.2.4.9.3.1.4.1.1.2 | OCTET STRING (SIZE (0..15)) | RW | mandatory |
column · OCTET STRING (SIZE (0..15)) · read-write · mandatory SNMP Community entry name. | ||||
| CsnmpCommunityEntryCommunityIpAddress1 | 1.3.6.1.4.1.2.3.51.2.4.9.3.1.4.1.1.3 | OCTET STRING (SIZE (0..63)) | RW | mandatory |
column · OCTET STRING (SIZE (0..63)) · read-write · mandatory SNMP Community IP address or host name. Can either be a dotted decimal IP string (e.g. 9.37.44.2) or if DNS is enabled a host name. This field also allows two wildard values for read-Traps and write-Read-Traps communities: 0.0.0.0 - allow any IPv4 address 0::0 - allow any IPv6 address | ||||
| CsnmpCommunityEntryCommunityIpAddress2 | 1.3.6.1.4.1.2.3.51.2.4.9.3.1.4.1.1.4 | OCTET STRING (SIZE (0..63)) | RW | mandatory |
column · OCTET STRING (SIZE (0..63)) · read-write · mandatory SNMP Community IP address or host name. Can either be a dotted decimal IP string (e.g. 9.37.44.2) or if DNS is enabled a host name. This field also allows two wildard values for read-Traps and write-Read-Traps communities: 0.0.0.0 - allow any IPv4 address 0::0 - allow any IPv6 address | ||||
| CsnmpCommunityEntryCommunityIpAddress3 | 1.3.6.1.4.1.2.3.51.2.4.9.3.1.4.1.1.5 | OCTET STRING (SIZE (0..63)) | RW | mandatory |
column · OCTET STRING (SIZE (0..63)) · read-write · mandatory SNMP Community IP address or host name. Can either be a dotted decimal IP string (e.g. 9.37.44.2) or if DNS is enabled a host name. This field also allows two wildard values for read-Traps and write-Read-Traps communities: 0.0.0.0 - allow any IPv4 address 0::0 - allow any IPv6 address | ||||
| CsnmpCommunityEntryCommunityViewType | 1.3.6.1.4.1.2.3.51.2.4.9.3.1.4.1.1.6 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Access Level of the SNMPv1 managers. Note this parameter is set for each community. Therefore all three managers in the same community have the same access level.
| ||||
| Ssnmpv1SystemAgentEnable | 1.3.6.1.4.1.2.3.51.2.4.9.3.1.5 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Disable or enable the SNMPv1 agent. NOTE: Restart the management module if this MIB object is changed with respect to the value at system bootup time. For example the SNMPv1 agent was set to disabled at system bootup time and now it is enabled. Then restarting the remote supervisor is required. Also note that when attempting to enable this agent, the following are verified: (1) Is there a valid system contact (2) Is there a valid system name (3) Is there at least one valid community name and for that community name is there one valid IP address or hostname (4) Are all defined community names unique If this verification fails an error response will be returned and the SNMPv1 agent will be left disabled.
| ||||
| Ssnmpv3SystemAgentEnable | 1.3.6.1.4.1.2.3.51.2.4.9.3.1.6 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Disable or enable the SNMPv3 agent. NOTE: Restart the management module if this MIB object is changed with respect to the value at system bootup time. For example the SNMPv3 agent was set to disabled at system bootup time and now it is enabled. Then restarting the remote supervisor is required. Also note that when attempting to enable this agent, the following are verified: (1) Is there a valid system contact? (2) Is there a valid system name? If this verification fails an error response will be returned and the SNMPv3 agent will be left disabled.
| ||||
| NsnmpAgentUserProfileConfig | 1.3.6.1.4.1.2.3.51.2.4.9.3.1.9 | |||
| TsnmpUserProfileTable | 1.3.6.1.4.1.2.3.51.2.4.9.3.1.9.1 | NA | mandatory | |
table · not-accessible · mandatory Table of SNMPv3 User Profile entries | ||||
| RsnmpUserProfileEntry | 1.3.6.1.4.1.2.3.51.2.4.9.3.1.9.1.1 | NA | mandatory | |
| CsnmpUserProfileEntryIndex | 1.3.6.1.4.1.2.3.51.2.4.9.3.1.9.1.1.1 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Index for SNMPv3 Agent User Profile entry. | ||||
| CsnmpUserProfileEntryContextName | 1.3.6.1.4.1.2.3.51.2.4.9.3.1.9.1.1.3 | OCTET STRING (SIZE (0..31)) | RW | mandatory |
column · OCTET STRING (SIZE (0..31)) · read-write · mandatory SNMPv3 User Profile entry - Context name for users to access MIB objects. Note that context names can be duplicates and can be shared among users. Empty context names are allowed. The default context name is the empty string. | ||||
| CsnmpUserProfileEntryAuthProt | 1.3.6.1.4.1.2.3.51.2.4.9.3.1.9.1.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory SNMPv3 User Profile entry - Authentication Protocol supported by the user.
| ||||
| CsnmpUserProfileEntryPrivProt | 1.3.6.1.4.1.2.3.51.2.4.9.3.1.9.1.1.6 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory SNMPv3 User Profile entry - Privacy Protocol supported by the user. The Privacy Password must be set and the Authentication Protocol must be md5 or sha before this field may be set to des or aes.
| ||||
| CsnmpUserProfileEntryPrivPassword | 1.3.6.1.4.1.2.3.51.2.4.9.3.1.9.1.1.7 | OCTET STRING (SIZE (0..31)) | RW | mandatory |
column · OCTET STRING (SIZE (0..31)) · read-write · mandatory SNMPv3 User Profile entry - Privacy password for the user. NOTE: Value returned for the GET command is meaningless for this MIB object for security reasons. | ||||
| CsnmpUserProfileEntryViewType | 1.3.6.1.4.1.2.3.51.2.4.9.3.1.9.1.1.8 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory SNMPv3 User Profile entry - Access level (Get, Set, and Traps) of the user.
| ||||
| CsnmpUserProfileEntryIpAddress | 1.3.6.1.4.1.2.3.51.2.4.9.3.1.9.1.1.9 | OCTET STRING (SIZE (0..63)) | RW | mandatory |
column · OCTET STRING (SIZE (0..63)) · read-write · mandatory SNMPv3 User Profile entry - IP address or host name. Can either be a dotted decimal IP string (e.g. 9.37.44.2) or if DNS is enabled a host name. | ||||
| CsnmpUserProfileEntryUserId | 1.3.6.1.4.1.2.3.51.2.4.9.3.1.9.1.1.10 | OCTET STRING (SIZE (0..31)) | RO | mandatory |
column · OCTET STRING (SIZE (0..31)) · read-only · mandatory The userid for the SNMPv3 Agent User Profile entry. | ||||
| NdnsConfig | 1.3.6.1.4.1.2.3.51.2.4.9.3.2 | |||
| SdnsEnabled | 1.3.6.1.4.1.2.3.51.2.4.9.3.2.1 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Disable or enable the DNS agent. NOTE: To alter any of the configuration settings for the DNS agent, the following procedure should be used: (1) This object should be set to 'disabled' (2) Make the modifications to other settings (3) This object should be set to 'enabled' Also note that when attempting to enable this agent, it is verified that there is at least one valid DNS server IP address. If this verification fails, an error response will be returned and the DNS agent will be left disabled.
| ||||
| SdnsServerIPAddress1 | 1.3.6.1.4.1.2.3.51.2.4.9.3.2.2 | IpAddress | RW | mandatory |
scalar · IpAddress · read-write · mandatory Contains the primary DNS server IP address. | ||||
| SdnsServerIPAddress2 | 1.3.6.1.4.1.2.3.51.2.4.9.3.2.3 | IpAddress | RW | mandatory |
scalar · IpAddress · read-write · mandatory Contains the secondary DNS server IP address. | ||||
| SdnsServerIPAddress3 | 1.3.6.1.4.1.2.3.51.2.4.9.3.2.4 | IpAddress | RW | mandatory |
scalar · IpAddress · read-write · mandatory Contains the tertiary DNS server IP address. | ||||
| SdnsServerIPv6Address1 | 1.3.6.1.4.1.2.3.51.2.4.9.3.2.12 | InetAddressIPv6 | RW | mandatory |
scalar · InetAddressIPv6 · read-write · mandatory Contains the primary IPv6 DNS server address. | ||||
| SdnsServerIPv6Address2 | 1.3.6.1.4.1.2.3.51.2.4.9.3.2.13 | InetAddressIPv6 | RW | mandatory |
scalar · InetAddressIPv6 · read-write · mandatory Contains the secondary IPv6 DNS server address. | ||||
| SdnsServerIPv6Address3 | 1.3.6.1.4.1.2.3.51.2.4.9.3.2.14 | InetAddressIPv6 | RW | mandatory |
scalar · InetAddressIPv6 · read-write · mandatory Contains the tertiary IPv6 DNS server address. | ||||
| SdnsPriority | 1.3.6.1.4.1.2.3.51.2.4.9.3.2.20 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Tells the order host names are resolved. The options are to either first resolve with an IPv6 DNS server or to first resolve with an IPv6 DNS server.
| ||||
| NsmtpConfig | 1.3.6.1.4.1.2.3.51.2.4.9.3.3 | |||
| SsmtpServerNameOrIPAddress | 1.3.6.1.4.1.2.3.51.2.4.9.3.3.1 | OCTET STRING (SIZE (0..64)) | RW | mandatory |
scalar · OCTET STRING (SIZE (0..64)) · read-write · mandatory A NULL terminated 64 byte string that contains the SMTP server host name or IP address (a.b.c.d). | ||||
| SattachmentsToEmailAlerts | 1.3.6.1.4.1.2.3.51.2.4.9.3.3.2 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Indicates if the service information should be attached to an email alert.
| ||||
| SsmtpEmailDomain | 1.3.6.1.4.1.2.3.51.2.4.9.3.3.3 | OCTET STRING (SIZE (0..64)) | RW | mandatory |
scalar · OCTET STRING (SIZE (0..64)) · read-write · mandatory A NULL terminated string that contains the SMTP email domain. If this field is empty, the MM IP address is used as the domain. However, some SMTP servers (e.g. - MS Exchange 2007) do not accept an IP address and instead require a domain name. This object can be used to set that email domain name. | ||||
| NtcpApplicationConfig | 1.3.6.1.4.1.2.3.51.2.4.9.3.4 | |||
| StelnetInactivityTimeout | 1.3.6.1.4.1.2.3.51.2.4.9.3.4.1 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Default is 120 seconds. Value of zero is no timeout. Max value is any positive 4 bytes value. Note that SSH also uses this timeout value to wait before disconnecting inactive SSH connections. | ||||
| ScommandModeInactivityTimeout | 1.3.6.1.4.1.2.3.51.2.4.9.3.4.2 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory The amount of time in seconds before the (Secure)TCP Command Mode times out. Default value of 0 means no timeout. Max value is any positive 4 byte value. | ||||
| SsecureCommandModeEnable | 1.3.6.1.4.1.2.3.51.2.4.9.3.4.3 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Set Secure TCP Command Mode number of connections. MM will provide a max of 20 connections for both Secure TCP Command Mode and TCP Command Mode. A value of 0 means disabled. If no valid server certificate is in place, Secure TCP Command Mode will not be allowed to set to enable. | ||||
| ScommandModeEnable | 1.3.6.1.4.1.2.3.51.2.4.9.3.4.4 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Set TCP Command Mode number of connections. MM will provide a max of 20 connections for both Secure TCP Command Mode and TCP Command Mode. A value of 0 means disabled. | ||||
| SslpAddrType | 1.3.6.1.4.1.2.3.51.2.4.9.3.4.5 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Set SLP address type to 0 (multicast) or 1 (broadcast). Note that when slpAddrType is set to broadcast value then the multicast address set in slpMulticastAddr will be ignored.
| ||||
| SslpEnable | 1.3.6.1.4.1.2.3.51.2.4.9.3.4.7 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Disable/Enable Service Location Protocol. NOTE: Change to Service Location Protocol will take effect after the next restart of the MM.
| ||||
| StelnetEnable | 1.3.6.1.4.1.2.3.51.2.4.9.3.4.9 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Disable/Enable telnet. NOTE: Change to telnet enable/disable will take effect immediately.
| ||||
| SsshEnable | 1.3.6.1.4.1.2.3.51.2.4.9.3.4.10 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Disable/Enable SSH.
| ||||
| SsslServerEnable | 1.3.6.1.4.1.2.3.51.2.4.9.3.4.15 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Disable/Enable SSL Server.
| ||||
| SsslClientEnable | 1.3.6.1.4.1.2.3.51.2.4.9.3.4.16 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Disable/Enable SSL Client. If no valid client or server certificate is in place, SSL client will not be allowed to set to enable.
| ||||
| SftpEnable | 1.3.6.1.4.1.2.3.51.2.4.9.3.4.17 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Disable/Enable FTP.
| ||||
| SsftpEnable | 1.3.6.1.4.1.2.3.51.2.4.9.3.4.18 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Disable/Enable SFTP.
| ||||
| StftpEnable | 1.3.6.1.4.1.2.3.51.2.4.9.3.4.19 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Disable/Enable TFTP.
| ||||
| SftpTimeout | 1.3.6.1.4.1.2.3.51.2.4.9.3.4.23 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory The amount of time before FTP times out. Default is 300 seconds. Value of zero is no timeout. Max value is any positive 4 byte value. | ||||
| NmmSshServerConfig | 1.3.6.1.4.1.2.3.51.2.4.9.3.4.27 | |||
| TmmSshServerHostKeyTable | 1.3.6.1.4.1.2.3.51.2.4.9.3.4.27.1 | NA | mandatory | |
table · not-accessible · mandatory A table that contains per public/private host key pair information. | ||||
| RmmSshServerHostKeyEntry | 1.3.6.1.4.1.2.3.51.2.4.9.3.4.27.1.1 | NA | mandatory | |
row · not-accessible · mandatory A list of information about a particular public/private host key pair. | ||||
| CmmSshServerHostKeyIndex | 1.3.6.1.4.1.2.3.51.2.4.9.3.4.27.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The index of the public/private host key pair. | ||||
| CmmSshServerHostKeyType | 1.3.6.1.4.1.2.3.51.2.4.9.3.4.27.1.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The type of the public/private host key pair.
| ||||
| CmmSshServerHostKeySize | 1.3.6.1.4.1.2.3.51.2.4.9.3.4.27.1.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The size of the public/private host key pair. NOTE: The MM supports only the bits2048 value.
| ||||
| CmmSshServerHostKeyFingerprint | 1.3.6.1.4.1.2.3.51.2.4.9.3.4.27.1.1.4 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The RSA fingerprint of the public part of the host key pair. This value can be used with the SSH client to verify, on the initial connection, that the Secure Shell server responding to the request is the server running on the MM. | ||||
| SmmSshServerHostKeyGenerate | 1.3.6.1.4.1.2.3.51.2.4.9.3.4.27.2 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Initiate the new Host Keys generation process for the MM SSH Server. NOTE: Value returned for the GET command is meaningless for this MIB object.
| ||||
| SmmSshServerHostKeyGenerateProgress | 1.3.6.1.4.1.2.3.51.2.4.9.3.4.27.3 | OCTET STRING | RO | mandatory |
scalar · OCTET STRING · read-only · mandatory Indicate the progress of the key generation process. | ||||
| ScimEnable | 1.3.6.1.4.1.2.3.51.2.4.9.3.4.50 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Disable/Enable CIM (Common Information Model) interface. NOTE: Change to CIM enable/disable will take effect immediately.
| ||||
| NtcpPortAssignmentCfg | 1.3.6.1.4.1.2.3.51.2.4.9.3.5 | |||
| StcpPortsRestoreDefault | 1.3.6.1.4.1.2.3.51.2.4.9.3.5.1 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Reset all ports to default value. http: 80 https: 443 telnet: 23 ssh: 22 SNMP agent: 161 SNMP trap: 162 TCP Command Mode: 6090 Secure TCP Command Mode: 6091 FTP: 21 FTP Data: 20 TFTP: 69 SLP: 427 CIM: 5989 NOTE: Value returned for the GET command is meaningless for this MIB object.
| ||||
| ShttpPortAssignment | 1.3.6.1.4.1.2.3.51.2.4.9.3.5.2 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory HTTP port number. Default value is 80. Once changed, the URL's have to include :port at the end. | ||||
| ShttpsPortAssignment | 1.3.6.1.4.1.2.3.51.2.4.9.3.5.3 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory SSL port number. Default value is 443. Once changed, the URL's have to include :port at the end. | ||||
| StelnetPortAssignment | 1.3.6.1.4.1.2.3.51.2.4.9.3.5.4 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Telnet port number. Default value is 23. Port change will take effect immediately. | ||||
| SsshPortAssignment | 1.3.6.1.4.1.2.3.51.2.4.9.3.5.5 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory SSH port number. Default value is 22. | ||||
| SsnmpAgentPortAssignment | 1.3.6.1.4.1.2.3.51.2.4.9.3.5.6 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory SNMP Agent port number. Default value is 161. Changes take effect after several seconds. | ||||
| SsnmpTrapsPortAssignment | 1.3.6.1.4.1.2.3.51.2.4.9.3.5.7 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory SNMP Traps port number. Default value is 162. Changes take effect after several seconds. | ||||
| ScommandModePortAssignment | 1.3.6.1.4.1.2.3.51.2.4.9.3.5.8 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory TCP Command Mode port number. Default value is 6090. Change will take effect immediately. | ||||
| SsecureCommandModePortAssignment | 1.3.6.1.4.1.2.3.51.2.4.9.3.5.9 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Secure TCP Command Mode port number. Default value is 6091. Change will take effect immediately. | ||||
| SftpPortAssignment | 1.3.6.1.4.1.2.3.51.2.4.9.3.5.13 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory FTP port number. Default value is 21. Port change will take effect immediately. | ||||
| SftpDataPortAssignment | 1.3.6.1.4.1.2.3.51.2.4.9.3.5.14 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory FTP Data port number. Default value is 20. Port change will take effect immediately. | ||||
| StftpPortAssignment | 1.3.6.1.4.1.2.3.51.2.4.9.3.5.15 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory TFTP port number. Default value is 69. | ||||
| SslpPortAssignment | 1.3.6.1.4.1.2.3.51.2.4.9.3.5.19 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Service Location Protocol port number. Default value is 427. NOTE: This value is normally required to be 427 to interoperate properly with other SLP enabled applications. | ||||
| ScimPortAssignment | 1.3.6.1.4.1.2.3.51.2.4.9.3.5.50 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory CIM (Common Information Model) port number. Default value is 5989. Port change will take effect immediately. | ||||
| NldapClientCfg | 1.3.6.1.4.1.2.3.51.2.4.9.3.6 | |||
| SldapServer1NameOrIPAddress | 1.3.6.1.4.1.2.3.51.2.4.9.3.6.1 | OCTET STRING (SIZE (0..256)) | RW | mandatory |
scalar · OCTET STRING (SIZE (0..256)) · read-write · mandatory A NULL terminated 255 byte string that contains the LDAP server host name or IP address (a.b.c.d). | ||||
| SldapServer1PortNumber | 1.3.6.1.4.1.2.3.51.2.4.9.3.6.2 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory LDAP server port number. | ||||
| SldapServer2NameOrIPAddress | 1.3.6.1.4.1.2.3.51.2.4.9.3.6.3 | OCTET STRING (SIZE (0..256)) | RW | mandatory |
scalar · OCTET STRING (SIZE (0..256)) · read-write · mandatory A NULL terminated 255 byte string that contains the LDAP server host name or IP address (a.b.c.d). | ||||
| SldapServer2PortNumber | 1.3.6.1.4.1.2.3.51.2.4.9.3.6.4 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory LDAP server port number. | ||||
| SldapServer3NameOrIPAddress | 1.3.6.1.4.1.2.3.51.2.4.9.3.6.5 | OCTET STRING (SIZE (0..256)) | RW | mandatory |
scalar · OCTET STRING (SIZE (0..256)) · read-write · mandatory A NULL terminated 255 byte string that contains the LDAP server host name or IP address (a.b.c.d). | ||||
| SldapServer3PortNumber | 1.3.6.1.4.1.2.3.51.2.4.9.3.6.6 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory LDAP server port number. | ||||
| SldapRootDN | 1.3.6.1.4.1.2.3.51.2.4.9.3.6.7 | OCTET STRING (SIZE (0..256)) | RW | mandatory |
scalar · OCTET STRING (SIZE (0..256)) · read-write · mandatory A NULL terminated 255 byte string that contains the distinguished Name for root entry of directory tree. An example might look like dn=foobar,dn=com. | ||||
| SldapGroupFilter | 1.3.6.1.4.1.2.3.51.2.4.9.3.6.9 | OCTET STRING (SIZE (0..511)) | RW | mandatory |
scalar · OCTET STRING (SIZE (0..511)) · read-write · mandatory This filter is used for group authentication. It specifies what group or groups that this MM belongs to. If left blank, group authentication is disabled. Otherwise, group authentication will be performed against the filter. The filter can be a specific group name (e.g. RSAWest), a wildcard (*) which matches everything, or a wildcard with a prefix (e.g. RSA*). The default filter is RSA*. After user authentication, group authentication will take place, whereby an attempt will be made to match the group or groups (that the user belongs to) to the group filter defined here. If there is no match, the user will not pass authentication and will be blocked. If there is a match, the login permissions for the user will be retrieved from the matched group(s), unless the user already has login permissions assigned directly from the user record retrieved from the LDAP server. | ||||
| SldapBindingMethod | 1.3.6.1.4.1.2.3.51.2.4.9.3.6.10 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory On initial binds to the LDAP server during user authentication, there are two options: Client authentication: Bind attempt is made with client DN and password specified by this configuration parameter. If the bind is successful, we proceed as above. User Principal Name (UPN): Bind attempt is made directly with the credentials used during the login process. If this succeeds, the user is deemed to have passed the user authentication phase. Note that for Active Directory servers, the userid can have the form someuser@somedomain or simply someuser.
| ||||
| SldapClientAuthenticationDN | 1.3.6.1.4.1.2.3.51.2.4.9.3.6.11 | OCTET STRING (SIZE (0..64)) | RW | mandatory |
scalar · OCTET STRING (SIZE (0..64)) · read-write · mandatory The initial bind to the LDAP server during user authentication can be performed with anonymous authentication, client based authentication, or UPN. The client based option requires a client DN and password as parameters to the bind request. These parameters are configured here. Note that the password can be left blank. | ||||
| SldapClientAuthenticationPassword | 1.3.6.1.4.1.2.3.51.2.4.9.3.6.12 | OCTET STRING (SIZE (0..16)) | RW | mandatory |
scalar · OCTET STRING (SIZE (0..16)) · read-write · mandatory The client authentication password | ||||
| SldapUIDsearchAttribute | 1.3.6.1.4.1.2.3.51.2.4.9.3.6.13 | OCTET STRING (SIZE (0..64)) | RW | mandatory |
scalar · OCTET STRING (SIZE (0..64)) · read-write · mandatory When the binding method selected is Anonymous authentication or Client authentication, the initial bind to the LDAP server is followed by a search request aimed at retrieving specific information about the user, including the user's DN, login permissions, and group ownerships. In order to retrieve this information, the search request must specify the attribute name used to represent userids on that server. Specifically, this name is used as a search filter against the login id entered by the user. This attribute name is configured here. If this field is left blank, a default of uid is used during user authentication. For example, on Active Directory servers, the attribute name used for userids is often sAMAccoutName. When the binding method selected is UPN or Strict UPN, this field defaults automatically to userPrincipalName during user authentication if the userid entered has the form userid@somedomain. | ||||
| SldapGroupSearchAttribute | 1.3.6.1.4.1.2.3.51.2.4.9.3.6.14 | OCTET STRING (SIZE (0..64)) | RW | mandatory |
scalar · OCTET STRING (SIZE (0..64)) · read-write · mandatory When the MM Group Filter name is configured, it is necessary to retrieve from the LDAP server the list of groups that a particular user belongs to. This is required to do group authentication. In order to retrieve this list, the search filter sent to the server must specify the attribute name associated with groups. This field specifies this attribute name. If this field is left blank, the attribute name in the filter will default to memberOf. | ||||
| SldapLoginPermissionAttribute | 1.3.6.1.4.1.2.3.51.2.4.9.3.6.15 | OCTET STRING (SIZE (0..64)) | RW | mandatory |
scalar · OCTET STRING (SIZE (0..64)) · read-write · mandatory When a user successfully authenticates via a LDAP server, it is necessary to retrieve the login permissions for this user. In order to retrieve these permissions, the search filter sent to the server must specify the attribute name associated with login permissions. This field specifies this attribute name. | ||||
| SldapUseDNSOrPreConfiguredServers | 1.3.6.1.4.1.2.3.51.2.4.9.3.6.16 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory The MM contains a Version 2.0 LDAP Client that may be configured to provide user authentication through one or more LDAP servers. The LDAP server(s) to be used for authentication can be discovered dynamically or manually pre-configured. If the usePreConfiguredLDAPServers option is selected, up to 4 LDAP servers can be configured. Simply enter the server's IP address or hostname (assuming DNS is enabled). The port number for each server is optional. If left blank, the default value of 389 is used for non-secured LDAP connections. For secured connections, the default is 636. At least one server must be configured. If the useDNSToFindLDAPServers is selected, the domain name need to be provided. For LDAP Authentication Only mode, additional information such as the forest name also need to be provided.
| ||||
| SldapRBSModelCfg | 1.3.6.1.4.1.2.3.51.2.4.9.3.6.20 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory There are two mechanisms to authenticate and authorize users on the MM when using an LDAP-enabled server. The first mechanism (oldPermissionString), also known as version 1, uses bitstrings to associate permissions to users and groups. Version1 supports Active Directory, Novell eDirectory, and OPenLDAP based servers. The second mechanism (newRBSModel), also known as version 2, uses a new Role-Based-Security (RBS) model. This mechanism is only available for Active Directory servers, and requires the use of a snap-in that runs on any windows platform. This snap-in tool allows you to configure roles on an Active Directory server of your choice, and to associate users/groups and MMs to those roles. A role identifies the permissions given to users and groups associated with that role, and also identifies the targets (e.g. MM) to which this role is attached. The use of bitstrings in version 2 disappears, making the configuration much more manageable and user-friendly. Note that if you are not using Active Directory, then you should not enable version 2. Also note that before enabling version 2, you should already have your roles configured on your Active Directory server. The old version 1 bitstring model cannot be automatically converted to the new version 2 model. This is why you must configure your users and groups before enabling version 2. Once enabled, the change takes effect immediately. The default value for this field is oldPermissionString.
| ||||
| SldapTargetName | 1.3.6.1.4.1.2.3.51.2.4.9.3.6.21 | OCTET STRING (SIZE (0..16)) | RW | mandatory |
scalar · OCTET STRING (SIZE (0..16)) · read-write · mandatory When administrator chooses Enhanced Role Based Security authentication model, he can associate one MM with one managed target object in Snap-in (one tool to configure LDAP users permission) via one target name. The MM target name can be looked as alias of MM, administrator can change it according to his configuration requirements. This is a string of up to 63 characters (plus the null character) | ||||
| SldapAuthCfg | 1.3.6.1.4.1.2.3.51.2.4.9.3.6.22 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory If ldapAuthCfg is set to 0, LDAP server is used to authenticate and authorize users. If it is set to 1, LDAP server is only used to authenticate users. Note:LDAP Authentication Only mode is currently supported only in an Active Directory environment.
| ||||
| SldapForestName | 1.3.6.1.4.1.2.3.51.2.4.9.3.6.23 | OCTET STRING (SIZE (0..64)) | RW | mandatory |
scalar · OCTET STRING (SIZE (0..64)) · read-write · mandatory LDAP Forest Name. Note: LDAP Forest Name is only for Active Directory environment. | ||||
| SldapDomainName | 1.3.6.1.4.1.2.3.51.2.4.9.3.6.24 | OCTET STRING (SIZE (0..256)) | RW | mandatory |
scalar · OCTET STRING (SIZE (0..256)) · read-write · mandatory A NULL terminated 255 byte string that contains the LDAP Domain Name. | ||||
| SldapServer4NameOrIPAddress | 1.3.6.1.4.1.2.3.51.2.4.9.3.6.25 | OCTET STRING (SIZE (0..256)) | RW | mandatory |
scalar · OCTET STRING (SIZE (0..256)) · read-write · mandatory A NULL terminated 255 byte string that contains the LDAP server host name or IP address (a.b.c.d). | ||||
| SldapServer4PortNumber | 1.3.6.1.4.1.2.3.51.2.4.9.3.6.26 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory LDAP server port number. | ||||
| NuplinkCheckConfig | 1.3.6.1.4.1.2.3.51.2.4.9.3.7 | |||
| SuplinkCheckEnabled | 1.3.6.1.4.1.2.3.51.2.4.9.3.7.1 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Disable or enable network uplink checking for physical detection. NOTE: This MIB object is only applicable to systems with a standby MM.
| ||||
| SuplinkCheckDelay | 1.3.6.1.4.1.2.3.51.2.4.9.3.7.2 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Delay, in minutes (1-2880), between discovery of a failed network uplink and the subsequent MM failover for physical detection. NOTE: This MIB object is only applicable to systems with a standby MM. | ||||
| SlogicalUplinkDestination | 1.3.6.1.4.1.2.3.51.2.4.9.3.7.3 | IpAddress | RW | mandatory |
scalar · IpAddress · read-write · mandatory Destination IP for MM to check its logical link. Specify a non-zero IP Address in order to enable logical uplink checking. NOTE: This MIB object is only applicable to systems with a standby MM. | ||||
| SlogicalUplinkCheckEnabled | 1.3.6.1.4.1.2.3.51.2.4.9.3.7.4 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Disable or enable network uplink checking for logical detection. logicalUplinkDestination must be set to a non-zero IP Address before enable logical uplink checking. NOTE: This MIB object is only applicable to systems with a standby MM.
| ||||
| SlogicalUplinkCheckDelay | 1.3.6.1.4.1.2.3.51.2.4.9.3.7.5 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Delay, in minutes(1-2880), between discovery of a failed network uplink and the subsequent MM failover for logical detection. NOTE: This MIB object is only applicable to systems with a standby MM. | ||||
| SphysicalUplinkCheckDelayInSecs | 1.3.6.1.4.1.2.3.51.2.4.9.3.7.6 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Delay, in seconds(10-172800), between discovery of a failed network uplink and the subsequent MM failover for physical detection. NOTE: This MIB object is only applicable to systems with a standby MM. | ||||
| SlogicalUplinkCheckDelayInSecs | 1.3.6.1.4.1.2.3.51.2.4.9.3.7.7 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Delay, in seconds(60-172800), between discovery of a failed network uplink and the subsequent MM failover for logical detection. NOTE: This MIB object is only applicable to systems with a standby MM. | ||||
| SlogicalUplinkIPv6Destination | 1.3.6.1.4.1.2.3.51.2.4.9.3.7.8 | InetAddressIPv6 | RW | mandatory |
scalar · InetAddressIPv6 · read-write · mandatory Destination IP for MM to check its logical link using IPv6. Specify a non-zero IP Address in order to enable logical uplink checking. NOTE: This MIB object is only applicable to systems with a standby MM. | ||||
| SlogicalUplinkFailoverPolicy | 1.3.6.1.4.1.2.3.51.2.4.9.3.7.9 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Determines when to failover if both an IPv4 and IPv6 destination have been configured. If set to 'either' the system will failover if either of the destination's link check fails. If set to 'both' then the IPv4 and IPv6 link checks must fail before a failover will happen. NOTE: This MIB object is only applicable to systems with a standby MM.
| ||||
| NntpConfig | 1.3.6.1.4.1.2.3.51.2.4.9.3.8 | |||
| SntpEnable | 1.3.6.1.4.1.2.3.51.2.4.9.3.8.1 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Disable/Enable the NTP client. The client will update the MM system clock at the frequency specified.
| ||||
| SntpIpAddressHostname | 1.3.6.1.4.1.2.3.51.2.4.9.3.8.2 | OCTET STRING (SIZE (0..63)) | RW | mandatory |
scalar · OCTET STRING (SIZE (0..63)) · read-write · mandatory NTP server's IP address or hostname if DNS is enabled and configured. | ||||
| SntpUpdateFrequency | 1.3.6.1.4.1.2.3.51.2.4.9.3.8.3 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory The frequency in minutes that the NTP service runs. The value range is 0 to 45000. If the NTP update frequency is set to 0, the MM clock can only be synchronized with the NTP server manually. | ||||
| SntpLastUpdate | 1.3.6.1.4.1.2.3.51.2.4.9.3.8.4 | OCTET STRING | RO | mandatory |
scalar · OCTET STRING · read-only · mandatory The date and time that the NTP server last updated the system clock. | ||||
| SntpUpdateClock | 1.3.6.1.4.1.2.3.51.2.4.9.3.8.5 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Update the MM system clock with the specified NTP server. A valid NTP server must be configured first.
| ||||
| SntpAuthEntry | 1.3.6.1.4.1.2.3.51.2.4.9.3.8.6 | OCTET STRING | RW | mandatory |
scalar · OCTET STRING · read-write · mandatory The NTP v3 authentication entry to be used for time sync with a secure NTP server. The format of an authentication entry is <key index> <key type> <key>. <key index> must be an integer between 1 and 65535. <key type> must be M. <key> is the actual value of the authentication key as configured on the NTP server. The GET command returns back data in the format: <key index> <key type> It does not return the actual key. | ||||
| SntpAuthEnable | 1.3.6.1.4.1.2.3.51.2.4.9.3.8.7 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Enables/Disables NTP v3 authentication
| ||||
| NsyslogConfig | 1.3.6.1.4.1.2.3.51.2.4.9.3.9 | |||
| SsyslogSevFilterLevel | 1.3.6.1.4.1.2.3.51.2.4.9.3.9.1 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory syslogSevFilterLevel error/warning/information .
| ||||
| NsyslogCollectorConfig | 1.3.6.1.4.1.2.3.51.2.4.9.3.9.2 | |||
| TsyslogCollectorTable | 1.3.6.1.4.1.2.3.51.2.4.9.3.9.2.1 | NA | mandatory | |
table · not-accessible · mandatory Table of Syslog Collector entries | ||||
| RsyslogCollectorEntry | 1.3.6.1.4.1.2.3.51.2.4.9.3.9.2.1.1 | NA | mandatory | |
| CsyslogCollectorIndex | 1.3.6.1.4.1.2.3.51.2.4.9.3.9.2.1.1.1 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory Index for Syslog Collector entry. | ||||
| CsyslogCollectorHostnameOrIpAddress | 1.3.6.1.4.1.2.3.51.2.4.9.3.9.2.1.1.2 | OCTET STRING (SIZE (0..63)) | RW | mandatory |
column · OCTET STRING (SIZE (0..63)) · read-write · mandatory Syslog Collector IP address or host name. | ||||
| CsyslogCollectorPort | 1.3.6.1.4.1.2.3.51.2.4.9.3.9.2.1.1.3 | INTEGER (1..65535) | RW | mandatory |
column · INTEGER (1..65535) · read-write · mandatory Syslog Collector port number. | ||||
| CsyslogCollectorEnable | 1.3.6.1.4.1.2.3.51.2.4.9.3.9.2.1.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Syslog Collector enable/disable.
| ||||
| SsyslogTestPacket | 1.3.6.1.4.1.2.3.51.2.4.9.3.9.3 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Generate a test syslog packet. This will send a test syslog to all configured
and enabled syslog collectors to assist in validating the configuration.
NOTE: Value returned for the GET command is meaningless for this
MIB object.
| ||||
| NsolConfiguration | 1.3.6.1.4.1.2.3.51.2.4.10 | |||
| NsolGlobalConfig | 1.3.6.1.4.1.2.3.51.2.4.10.1 | |||
| SsolEnable | 1.3.6.1.4.1.2.3.51.2.4.10.1.1 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Disable/Enable SOL dynamically.
| ||||
| SsolAccumulateTimeout | 1.3.6.1.4.1.2.3.51.2.4.10.1.3 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory This value specifies how much time in millisecond SOL to buffer data before sending the next SOL packet since the last SOL packet was transmitted. Valid value from 5 ms to 1275 ms. The value is in 5 ms increment. Value is not in 5 ms increment will be truncated to a nearest 5s. Default value is 5 ms. | ||||
| SsolCharSendThreshold | 1.3.6.1.4.1.2.3.51.2.4.10.1.4 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory This value specifies how many characters SOL to buffer before sending the next SOL packet since the last SOL packet was transmitted. Valid value is from 1 to 251 | ||||
| SsolRetry | 1.3.6.1.4.1.2.3.51.2.4.10.1.5 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Retry count. Valid value from 0-7. 0 means no retries after packet is transmitted. Packet will be dropped if no ACK/NACK received by the time retries expired. | ||||
| SsolRetryInterval | 1.3.6.1.4.1.2.3.51.2.4.10.1.6 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Retry Interval in 10 ms increment. Sets the time that the SOL will wait before the first retry and the time between retries when sending SOL packets to the remote blade. Value range is from 0 to 2550 ms in 10 ms increment. 0 means retries will be sent back-to-back. | ||||
| SsolExitToCliKeySeq | 1.3.6.1.4.1.2.3.51.2.4.10.1.7 | OCTET STRING (SIZE (0..16)) | RW | mandatory |
scalar · OCTET STRING (SIZE (0..16)) · read-write · mandatory This is the keystroke sequence used to escape out of SOL session and back to CLI
console. This sequence must have at least one character. The caret symbol (^)
has a special meaning in this sequence. It denotes 'Ctrl' for keystrokes that
map to Ctrl sequences (for example, ^[ for the escape key and ^M for carriage
return). All occurrences of ^ will be interpreted as part of a Ctrl sequence.
Refer to an ASCII-to-key conversion table for a complete list of Ctrl sequences.
The default value for this field is '^[(' i.e. ESC followed by (. | ||||
| SsolResetBladeKeySeq | 1.3.6.1.4.1.2.3.51.2.4.10.1.8 | OCTET STRING (SIZE (0..16)) | RW | mandatory |
scalar · OCTET STRING (SIZE (0..16)) · read-write · mandatory This is the keystroke sequence used to reset the blade while in SOL session console. This sequence must have at least one character. The caret symbol (^) has a special meaning in this sequence. It denotes 'Ctrl' for keystrokes that map to Ctrl sequences (for example, ^[ for the escape key and ^M for carriage return). All occurrences of ^ will be interpreted as part of a Ctrl sequence. Refer to an ASCII-to-key conversion table for a complete list of Ctrl sequences. The default value for this field is '^[R^[r^[R' i.e. ESC R ESC r ESC R. | ||||
| NsolBladeConfig | 1.3.6.1.4.1.2.3.51.2.4.10.2 | |||
| TsolBladeTable | 1.3.6.1.4.1.2.3.51.2.4.10.2.1 | NA | mandatory | |
table · not-accessible · mandatory SOL Blade configuration table. | ||||
| RsolBladeEntry | 1.3.6.1.4.1.2.3.51.2.4.10.2.1.1 | NA | mandatory | |
| CsolBladeIndex | 1.3.6.1.4.1.2.3.51.2.4.10.2.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory SOL Blade table index. | ||||
| CsolBladeName | 1.3.6.1.4.1.2.3.51.2.4.10.2.1.1.2 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The name of the blade as a null terminated string. | ||||
| CsolBladeEnable | 1.3.6.1.4.1.2.3.51.2.4.10.2.1.1.3 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Disable or enable a SOL on a blade.
| ||||
| CsolBladeIpAddr | 1.3.6.1.4.1.2.3.51.2.4.10.2.1.1.4 | IpAddress | RO | deprecated |
column · IpAddress · read-only · deprecated This is deprecated in favor of solBladeIpAddr6.
IP address of the blade derived from the IP address range for the blade
system management processors on the blades.
NOTE: The IPv6 address for a blade can be view with the
bladeIPv6AddressTable. | ||||
| CsolBladeSessionStatus | 1.3.6.1.4.1.2.3.51.2.4.10.2.1.1.5 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Status of a blade SOL session: solSessionNotReady: no SOL session connected to the blade. solSessionReady: there is an SOL session to the blade. solSessionActive: there is an SOL session to the blade and there is a client using the SOL session.
| ||||
| CsolBladeCapability | 1.3.6.1.4.1.2.3.51.2.4.10.2.1.1.6 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Display whether or not the blade support SOL feature.
| ||||
| CsolBladeIpAddr6 | 1.3.6.1.4.1.2.3.51.2.4.10.2.1.1.7 | InetAddressIPv6 | RO | mandatory |
column · InetAddressIPv6 · read-only · mandatory IPv6 address of the blade. | ||||
| CsolBladeRetryInterval | 1.3.6.1.4.1.2.3.51.2.4.10.2.1.1.8 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Retry interval time in miliseconds. | ||||
| CsolBladeRetryCount | 1.3.6.1.4.1.2.3.51.2.4.10.2.1.1.9 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Retry count. | ||||
| CsolBladeBytesSent | 1.3.6.1.4.1.2.3.51.2.4.10.2.1.1.10 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Number of bytes sent. | ||||
| CsolBladeBytesReceived | 1.3.6.1.4.1.2.3.51.2.4.10.2.1.1.11 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Number of bytes received. | ||||
| CsolBladeDestinationMAC | 1.3.6.1.4.1.2.3.51.2.4.10.2.1.1.12 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory MAC address of the blade. | ||||
| CsolBladeConsoleUserId | 1.3.6.1.4.1.2.3.51.2.4.10.2.1.1.13 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Sol console user name. | ||||
| CsolBladeConsoleLoginFrom | 1.3.6.1.4.1.2.3.51.2.4.10.2.1.1.14 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The location information from where the SOL console is logged in. | ||||
| CsolBladeConsoleLoginStart | 1.3.6.1.4.1.2.3.51.2.4.10.2.1.1.15 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The time that SOL console starts. | ||||
| CsolBladeConsoleLoginEnd | 1.3.6.1.4.1.2.3.51.2.4.10.2.1.1.16 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The time that SOL console ends. | ||||
| NchassisInternalNetwork | 1.3.6.1.4.1.2.3.51.2.4.11 | |||
| ScinsSupported | 1.3.6.1.4.1.2.3.51.2.4.11.1 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory Number of Chassis Internal Network (CIN) definitions supported. Currently a maximum of 14 CIN definitions can be supported. | ||||
| ScinGlobalEnable | 1.3.6.1.4.1.2.3.51.2.4.11.2 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Disable/Enable Chassis Internal Network (CIN) function dynamically.
Enabled:
MM reads the CIN entries. For each enabled entry,
- If the CIN VLAN ID is new and does not have a CIN interface
created yet then create a new CIN interface based on that
CIN VLAN ID. Use the CIN IP address from the entry to create
a host route.
- If the CIN IP address is 0.0.0.0 then start ARP monitoring.
Disabled:
- Stop all ARP monitoring.
- Delete all host routes.
- Delete all CIN interfaces.
| ||||
| TcinTable | 1.3.6.1.4.1.2.3.51.2.4.11.3 | NA | mandatory | |
table · not-accessible · mandatory Chassis Internal Network (CIN) configuration table. | ||||
| RcinEntry | 1.3.6.1.4.1.2.3.51.2.4.11.3.1 | NA | mandatory | |
| CcinIndex | 1.3.6.1.4.1.2.3.51.2.4.11.3.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Chassis Internal Network (CIN) table index. | ||||
| CcinDefExists | 1.3.6.1.4.1.2.3.51.2.4.11.3.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates if a Chassis Internal Network (CIN) definition exists for this index or not.
| ||||
| CcinDelete | 1.3.6.1.4.1.2.3.51.2.4.11.3.1.3 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Delete Chassis Internal Network (CIN) definition. Works like CIN entry disabled. However, the entry is also deleted. NOTE: Value returned for the GET command is meaningless for this MIB object. Deleting a non-defined entry does nothing.
| ||||
| CcinEnable | 1.3.6.1.4.1.2.3.51.2.4.11.3.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Disable or enable a Chassis Internal Network (CIN) definition.
Enabled:
MM reads the entry and creates a new CIN interface if the CIN VLAN
ID is new and does not have a CIN interface created yet, adds host
route, and monitors communication path. Start ARP monitoring if
IP is 0.0.0.0.
Disabled:
Delete host route. If this is the last IP address that uses the CIN
interface,
- Stop ARP monitoring if IP is 0.0.0.0.
- Delete the CIN interface if there is no other entry depends on it.
| ||||
| CcinId | 1.3.6.1.4.1.2.3.51.2.4.11.3.1.5 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory This is the Chassis Internal Network (CIN) Virtual LAN (VLAN) ID for
the internal management network between the Management Module,
I/O Module, and the blade OS. The range of valid CIN VLAN IDs is
3 to 4094 (inclusive). This value cannot be the same as the
Serial Over LAN (SOL) or Concurrent KVM (cKVM) VLAN ID.
NOTE: If creating a new CIN definition, you must define cinId
before you define cinIpAddress.
NOTE: Before changing this value on an existing CIN definition,
you must first disable the definition. | ||||
| CcinIpAddress | 1.3.6.1.4.1.2.3.51.2.4.11.3.1.6 | IpAddress | RW | mandatory |
column · IpAddress · read-write · mandatory Chassis Internal Network (CIN) IP address.
Restrictions:
- CIN entries cannot have matching IP addresses, with the exception of 0.0.0.0.
- Multiple IP addresses of 0.0.0.0 with different VLAN IDs are allowed.
- The IP address cannot be multi-cast.
- The IP address cannot match the MM IP address.
- If the CIN IP address is 0.0.0.0, the blade IP address for CIN which is configured
in the blade's OS can not be in the same subnet as that of MM.
NOTE: If creating a new CIN definition, you must define cinId
before you define cinIpAddress.
NOTE: Before changing this value on an existing CIN definition,
you must first disable the definition.
NOTE: When ipv6 is enable on one interface, this column will
display all zero IPv4 address | ||||
| CcinIpv6Address | 1.3.6.1.4.1.2.3.51.2.4.11.3.1.7 | InetAddressIPv6 | RW | mandatory |
column · InetAddressIPv6 · read-write · mandatory Chassis Internal Network (CIN) IPv6 address NOTE: When ipv4 is enable on one interface,this column will display all zero IPv6 address. | ||||
| NcinStatus | 1.3.6.1.4.1.2.3.51.2.4.11.4 | |||
| TcinStatusTable | 1.3.6.1.4.1.2.3.51.2.4.11.4.1 | NA | mandatory | |
table · not-accessible · mandatory Table of Chassis Internal Network (CIN) status entry information. | ||||
| RcinStatusEntry | 1.3.6.1.4.1.2.3.51.2.4.11.4.1.1 | NA | mandatory | |
row · not-accessible · mandatory Chassis Internal Network (CIN) status table entry.
| ||||
| CcinStatusIndex | 1.3.6.1.4.1.2.3.51.2.4.11.4.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The Chassis Internal Network (CIN) status log index number. For consistent results, view as a table and not as individual entries. | ||||
| CcinStatusString | 1.3.6.1.4.1.2.3.51.2.4.11.4.1.1.2 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Status of a Chassis Internal Network (CIN) connection. For example:
Index:1 VLANID:4094 IPADDR:192.168.70.100 MAC:01:0A:0B:00:01:01 Type:Learned Status:Operational
Index is the status entry number in the status table. Followed by the
VLAN ID, IP address, and MAC address that the Management Module is
communicating with on the CIN connection.
Type is either 'Configured' or 'Learned'. Learned implies that the
Management Module dynamically discovered the IP address.
Configured means that the address was explicitly configured in
the Management Module.
Status can be 'Operational', 'Not Operational', or 'Disabled'.
'Operational' means the Management Module can ping the CIN IP address.
'Not Operational' means that the Management Module cannot ping the CIN
IP address. Verify that the blade and I/O Module are configured properly
and that their configurations are compatible with the Management Module.
The blade OS also needs to have an IP host route defined
(e.g. route add -host 192.168.70.100 eth0.4094).
I/O Modules need to have a VLAN defined containing the blade's and the
MM's port. Blade and I/O Modules need to be powered up and operational.
'Disabled' means that the CIN configuration has been disabled by a
Management Module administrator.
For consistent results, view as a table and not as individual entries. | ||||
| NrestartReset | 1.3.6.1.4.1.2.3.51.2.7 | |||
| SrestartSPImmediately | 1.3.6.1.4.1.2.3.51.2.7.4 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Restart the MM immediately. NOTE: Value returned for the GET command is meaningless for this MIB object.
| ||||
| SrestartStandbyMM | 1.3.6.1.4.1.2.3.51.2.7.5 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Restarts the Standby MM from the Primary MM. NOTE: Value returned for the GET command is meaningless for this MIB object. NOTE: This mib object is only applicable to systems with a standby MM.
| ||||
| SswitchOverRedundantMM | 1.3.6.1.4.1.2.3.51.2.7.7 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Switch over to the redundant Management Module. The failover will not occur if the standby or primary MM is in flashing mode. NOTE: Value returned for the GET command is meaningless for this MIB object. NOTE: This mib object is only applicable to systems with a redundant MM.
| ||||
| SresetSPConfigAndRestart | 1.3.6.1.4.1.2.3.51.2.7.20 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Will cause all the MM information to be reset to it's initial factory defaults (all previous configuration information is lost) and the MM will be re-started. NOTE: Value returned for the GET command is meaningless for this MIB object.
| ||||
| SresetSPConfigAndRestartSaveLogs | 1.3.6.1.4.1.2.3.51.2.7.21 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Will cause all the MM information to be reset to it's initial factory defaults (all previous configuration information is lost) and the MM will be re-started. The logs will be saved. NOTE: Value returned for the GET command is meaningless for this MIB object.
| ||||
| Ncomponents | 1.3.6.1.4.1.2.3.51.2.22 | |||
| NprocessorBlade | 1.3.6.1.4.1.2.3.51.2.22.1 | |||
| NbladePolicyControl | 1.3.6.1.4.1.2.3.51.2.22.1.4 | |||
| TbladePolicyControlTable | 1.3.6.1.4.1.2.3.51.2.22.1.4.1 | NA | mandatory | |
table · not-accessible · mandatory Table of blade power policy control information. Contains power on/off enablement status for each blade. | ||||
| RbladePolicyControlEntry | 1.3.6.1.4.1.2.3.51.2.22.1.4.1.1 | NA | mandatory | |
| CpolicyControlIndex | 1.3.6.1.4.1.2.3.51.2.22.1.4.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Blade power policy control index. | ||||
| CpolicyControlBladeId | 1.3.6.1.4.1.2.3.51.2.22.1.4.1.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The numeric blade ID.
| ||||
| CpolicyControlBladeExists | 1.3.6.1.4.1.2.3.51.2.22.1.4.1.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether the server blade specified exists or not.
| ||||
| CpolicyControlBladePowerState | 1.3.6.1.4.1.2.3.51.2.22.1.4.1.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The power state for blade. 0 = off, 1 = on, 3 = standby, 4 = hibernate, 255 = unknown.
| ||||
| CpolicyControlBladeHealthState | 1.3.6.1.4.1.2.3.51.2.22.1.4.1.1.5 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The system health state for the blade. Unknown: Blade is in an undefined state. Good: Blade is operating normally. Warning: One or more outstanding warnings exist for this blade. Critical: One or more outstanding critical events for this blade. Kernel Mode: Blade is in kernel mode. Discovering: The MM is currently in the process of discovering this blade. Communications Error: The MM failed to communicate with this blade. No Power: No power to the blade's domain. Flashing: Flashing in progress. Initialization Failure: Blade failed to initialized. Insufficient Power: Not enough power is left in the blade's domain to power the blade. Power Denied: Power was denied to the blade.
| ||||
| CpolicyControlBladeName | 1.3.6.1.4.1.2.3.51.2.22.1.4.1.1.6 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The name of the blade as a null terminated string. | ||||
| CpolicyLocalPowerControlEnable | 1.3.6.1.4.1.2.3.51.2.22.1.4.1.1.7 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Blade local power policy control enablement status.
| ||||
| CpolicyWakeOnLanControlEnable | 1.3.6.1.4.1.2.3.51.2.22.1.4.1.1.10 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Blade Wake On LAN enablement status. If WOL is not supported by the blade, it displays 'notApplicable' and WOL can not be enabled or disabled.
| ||||
| NbladePolicy | 1.3.6.1.4.1.2.3.51.2.22.1.4.2 | |||
| SbladePolicyLocalPowerControlEnable | 1.3.6.1.4.1.2.3.51.2.22.1.4.2.1 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Blade local power control enablement status policy.
| ||||
| SbladePolicyWakeOnLanControlEnable | 1.3.6.1.4.1.2.3.51.2.22.1.4.2.4 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Blade Wake On LAN enablement status policy. The notApplicable(255) enumeration is not valid for SET operations. NOTE: Value returned for the GET command is meaningless for this MIB object.
| ||||
| NbladeMonitors | 1.3.6.1.4.1.2.3.51.2.22.1.5 | |||
| TbladeSystemStatusTable | 1.3.6.1.4.1.2.3.51.2.22.1.5.1 | NA | mandatory | |
table · not-accessible · mandatory Table of blade status information. | ||||
| RbladeSystemStatusEntry | 1.3.6.1.4.1.2.3.51.2.22.1.5.1.1 | NA | mandatory | |
| CbladeStatusIndex | 1.3.6.1.4.1.2.3.51.2.22.1.5.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Blade system status index. | ||||
| CbladeId | 1.3.6.1.4.1.2.3.51.2.22.1.5.1.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The numeric blade ID.
| ||||
| CbladeExists | 1.3.6.1.4.1.2.3.51.2.22.1.5.1.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether the server blade specified exists or not.
| ||||
| CbladePowerState | 1.3.6.1.4.1.2.3.51.2.22.1.5.1.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates the power state of the blade specified.
| ||||
| CbladeHealthState | 1.3.6.1.4.1.2.3.51.2.22.1.5.1.1.5 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The system health state for the blade. Unknown: Blade is in an undefined state. Good: Blade is operating normally. Warning: One or more outstanding warnings exist for this blade. Critical: One or more outstanding critical events for this blade. Kernel Mode: Blade is in kernel mode. Discovering: The MM is currently in the process of discovering this blade. Communications Error: The MM failed to communicate with this blade. No Power: No power to the blade's domain. Flashing: Flashing in progress. Initialization Failure: Blade failed to initialized. Insufficient Power: Not enough power is left in the blade's domain to power the blade. Power Denied: Power was denied to the blade.
| ||||
| CbladeName | 1.3.6.1.4.1.2.3.51.2.22.1.5.1.1.6 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The name of the blade as a null terminated string. | ||||
| CbladeRemotePowerEnable | 1.3.6.1.4.1.2.3.51.2.22.1.5.1.1.7 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Remote power state for the blade.
| ||||
| CbladeConnectionType | 1.3.6.1.4.1.2.3.51.2.22.1.5.1.1.10 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Connection type of the expansion card number one.
| ||||
| CbladeRemoteWakeOnLanEnable | 1.3.6.1.4.1.2.3.51.2.22.1.5.1.1.13 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Remote wake on LAN state for the blade.
| ||||
| CbladeServerExpansion | 1.3.6.1.4.1.2.3.51.2.22.1.5.1.1.14 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This shows whether this blade has an expansion board attached. A yes column indicates that an expansion board is installed for this blade.
| ||||
| CbladeWidth | 1.3.6.1.4.1.2.3.51.2.22.1.5.1.1.15 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The width of the blade including any supplement blade attached to it | ||||
| CbladeServerExpansion2 | 1.3.6.1.4.1.2.3.51.2.22.1.5.1.1.17 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This shows whether this blade has an expansion board attached. A yes column indicates that an expansion board is installed for this blade.
| ||||
| CbladeConnectionType2 | 1.3.6.1.4.1.2.3.51.2.22.1.5.1.1.22 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Connection type of the expansion card number 2.
| ||||
| CbladeConnectionType3 | 1.3.6.1.4.1.2.3.51.2.22.1.5.1.1.23 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Connection type of the expansion card number 3.
| ||||
| CbladeConnectionType4 | 1.3.6.1.4.1.2.3.51.2.22.1.5.1.1.24 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Connection type of the expansion card number 4.
| ||||
| CbladeConnectionType5 | 1.3.6.1.4.1.2.3.51.2.22.1.5.1.1.25 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Connection type of the expansion card number 5.
| ||||
| CbladeHighSpeedConnectionType | 1.3.6.1.4.1.2.3.51.2.22.1.5.1.1.41 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Connection type of the high speed expansion card number 1.
| ||||
| CbladeIOCompatibility | 1.3.6.1.4.1.2.3.51.2.22.1.5.1.1.51 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory I/O compatibility status for the blade.
The possible values and their meanings are as follows:
unknown: This indicates a communication error for the blade.
ok: This is the normal (good) case where the blade and the
corresponding I/O modules it is internally wired to have no
compatibility issues.
noIOMs: This means there are no I/O modules in any of the
corresponding I/O module bays this blade is internally wired to.
attention: This indicates that one or more of the corresponding
I/O modules are in communication error.
mismatch: This indicates one of the following cases:
Fabric types are incompatible
An unknown I/O module type
An unknown fabric type on the blade | ||||
| CbladeInventoryReady | 1.3.6.1.4.1.2.3.51.2.22.1.5.1.1.52 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory When a blade management controller or the MM is reset, the blade inventory data is refreshed in the MM database. This includes items like IBM VPD (e.g. - serial number, UUID) and MAC address information. Applications need to know when this information has been populated on the MM before they begin to query it using SNMP or other means. This simple flag object will return a ready or notReady indication for each blade regarding the status of this information. Notes: For blades that are experiencing a 'communication failure' or 'initialization failure' condition, this object will continue to indicate notReady until the condition is resolved. Therefore, any application that polls this object should also incorporate a timeout period.
| ||||
| TbladeHealthSummaryTable | 1.3.6.1.4.1.2.3.51.2.22.1.5.2 | NA | mandatory | |
table · not-accessible · mandatory Table of blade health summary information. Contains information about the overall blade health status. | ||||
| RbladeHealthSummaryEntry | 1.3.6.1.4.1.2.3.51.2.22.1.5.2.1 | NA | mandatory | |
| CbladeHealthSummaryIndex | 1.3.6.1.4.1.2.3.51.2.22.1.5.2.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Blade health summary index. | ||||
| CbladeHealthSummaryBladeId | 1.3.6.1.4.1.2.3.51.2.22.1.5.2.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The numeric blade ID.
| ||||
| CbladeHealthSummarySeverity | 1.3.6.1.4.1.2.3.51.2.22.1.5.2.1.3 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory System health summary severity. | ||||
| CbladeHealthSummaryDescription | 1.3.6.1.4.1.2.3.51.2.22.1.5.2.1.4 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory System health summary description. | ||||
| CbladeHealthSummaryDateTime | 1.3.6.1.4.1.2.3.51.2.22.1.5.2.1.5 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory System health summary date time. | ||||
| CbladeHealthSummaryEventID | 1.3.6.1.4.1.2.3.51.2.22.1.5.2.1.6 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory System health summary event ID. | ||||
| TbladeTemperaturesTable | 1.3.6.1.4.1.2.3.51.2.22.1.5.3 | NA | mandatory | |
table · not-accessible · mandatory Table of blade temperatures information. | ||||
| RbladeTemperaturesEntry | 1.3.6.1.4.1.2.3.51.2.22.1.5.3.1 | NA | mandatory | |
| CtemperatureIndex | 1.3.6.1.4.1.2.3.51.2.22.1.5.3.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Blade temperatures table index. | ||||
| CtemperatureBladeId | 1.3.6.1.4.1.2.3.51.2.22.1.5.3.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The numeric blade ID.
| ||||
| CtemperatureBladeExists | 1.3.6.1.4.1.2.3.51.2.22.1.5.3.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether the server blade specified exists or not.
| ||||
| CtemperatureBladePowerState | 1.3.6.1.4.1.2.3.51.2.22.1.5.3.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates the power state of the blade specified.
| ||||
| CtemperatureBladeName | 1.3.6.1.4.1.2.3.51.2.22.1.5.3.1.5 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The name of the blade as a null terminated string. | ||||
| CtemperatureCPU1 | 1.3.6.1.4.1.2.3.51.2.22.1.5.3.1.6 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The blade CPU temperature in degrees centigrade(C).
An octet string expressed as 'sddd.dd Centigrade' where:
s is the sign ('-' for negative or blank space for positive)
d is a decimal digit or blank space for leading zeroes.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Temperature' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CtemperatureCPU2 | 1.3.6.1.4.1.2.3.51.2.22.1.5.3.1.7 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The blade CPU temperature in degrees centigrade(C).
An octet string expressed as 'sddd.dd Centigrade' where:
s is the sign ('-' for negative or blank space for positive)
d is a decimal digit or blank space for leading zeroes.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Temperature' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CtemperatureCPU3 | 1.3.6.1.4.1.2.3.51.2.22.1.5.3.1.8 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The blade CPU temperature in degrees centigrade(C).
An octet string expressed as 'sddd.dd Centigrade' where:
s is the sign ('-' for negative or blank space for positive)
d is a decimal digit or blank space for leading zeroes.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Temperature' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CtemperatureCPU4 | 1.3.6.1.4.1.2.3.51.2.22.1.5.3.1.9 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The blade CPU temperature in degrees centigrade(C).
An octet string expressed as 'sddd.dd Centigrade' where:
s is the sign ('-' for negative or blank space for positive)
d is a decimal digit or blank space for leading zeroes.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Temperature' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CtemperatureDASD1 | 1.3.6.1.4.1.2.3.51.2.22.1.5.3.1.10 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The blade DASD temperature in degrees centigrade(C).
An octet string expressed as 'sddd.dd Centigrade' where:
s is the sign ('-' for negative or blank space for positive)
d is a decimal digit or blank space for leading zeroes.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Temperature' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensorTempCapability | 1.3.6.1.4.1.2.3.51.2.22.1.5.3.1.11 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether the server blade is IPMI capable or not.
| ||||
| CbladeSensor1Temp | 1.3.6.1.4.1.2.3.51.2.22.1.5.3.1.12 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Temperature reading for an IPMI blade expressed in degrees centigrade(C).
An octet string expressed as 'sddd.dd Centigrade' where:
s is the sign ('-' for negative or blank space for positive)
d is a decimal digit or blank space for leading zeroes.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Temperature' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor2Temp | 1.3.6.1.4.1.2.3.51.2.22.1.5.3.1.13 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Temperature reading for an IPMI blade expressed in degrees centigrade(C).
An octet string expressed as 'sddd.dd Centigrade' where:
s is the sign ('-' for negative or blank space for positive)
d is a decimal digit or blank space for leading zeroes.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Temperature' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor3Temp | 1.3.6.1.4.1.2.3.51.2.22.1.5.3.1.14 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Temperature reading for an IPMI blade expressed in degrees centigrade(C).
An octet string expressed as 'sddd.dd Centigrade' where:
s is the sign ('-' for negative or blank space for positive)
d is a decimal digit or blank space for leading zeroes.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Temperature' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor4Temp | 1.3.6.1.4.1.2.3.51.2.22.1.5.3.1.15 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Temperature reading for an IPMI blade expressed in degrees centigrade(C).
An octet string expressed as 'sddd.dd Centigrade' where:
s is the sign ('-' for negative or blank space for positive)
d is a decimal digit or blank space for leading zeroes.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Temperature' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor5Temp | 1.3.6.1.4.1.2.3.51.2.22.1.5.3.1.16 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Temperature reading for an IPMI blade expressed in degrees centigrade(C).
An octet string expressed as 'sddd.dd Centigrade' where:
s is the sign ('-' for negative or blank space for positive)
d is a decimal digit or blank space for leading zeroes.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Temperature' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor6Temp | 1.3.6.1.4.1.2.3.51.2.22.1.5.3.1.17 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Temperature reading for an IPMI blade expressed in degrees centigrade(C).
An octet string expressed as 'sddd.dd Centigrade' where:
s is the sign ('-' for negative or blank space for positive)
d is a decimal digit or blank space for leading zeroes.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Temperature' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor7Temp | 1.3.6.1.4.1.2.3.51.2.22.1.5.3.1.18 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Temperature reading for an IPMI blade expressed in degrees centigrade(C).
An octet string expressed as 'sddd.dd Centigrade' where:
s is the sign ('-' for negative or blank space for positive)
d is a decimal digit or blank space for leading zeroes.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Temperature' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor8Temp | 1.3.6.1.4.1.2.3.51.2.22.1.5.3.1.19 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Temperature reading for an IPMI blade expressed in degrees centigrade(C).
An octet string expressed as 'sddd.dd Centigrade' where:
s is the sign ('-' for negative or blank space for positive)
d is a decimal digit or blank space for leading zeroes.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Temperature' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor9Temp | 1.3.6.1.4.1.2.3.51.2.22.1.5.3.1.20 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Temperature reading for an IPMI blade expressed in degrees centigrade(C).
An octet string expressed as 'sddd.dd Centigrade' where:
s is the sign ('-' for negative or blank space for positive)
d is a decimal digit or blank space for leading zeroes.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Temperature' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| TbladeTemperatureThresholdsTable | 1.3.6.1.4.1.2.3.51.2.22.1.5.4 | NA | mandatory | |
table · not-accessible · mandatory Table of blade temperature thresholds information. | ||||
| RbladeTemperatureThresholdsEntry | 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1 | NA | mandatory | |
row · not-accessible · mandatory Blade temperature thresholds table entry | ||||
| CtemperatureThresholdIndex | 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Blade temperature threshold table index. | ||||
| CtemperatureThresholdBladeId | 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The numeric blade ID.
| ||||
| CtemperatureThresholdBladeExists | 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether the server blade specified exists or not.
| ||||
| CtemperatureThresholdBladePowerState | 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates the power state of the blade specified.
| ||||
| CtemperatureThresholdBladeName | 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.5 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The name of the blade as a null terminated string. | ||||
| CtemperatureCPU1HardShutdown | 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.6 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The blade CPU hard shutdown temperature in degrees
centigrade(C). If the component's temperature rises above
this value the system will be powered off immediately.
If enabled, a critical alert/event will be generated.
An octet string expressed as 'sddd.dd Centigrade' where:
s is the sign ('-' for negative or blank space for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Temperature' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CtemperatureCPU1Warning | 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.7 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The blade CPU warning temperature in degrees centigrade(C).
If the temperature rises above this value a warning alert/event
if enabled will be generated.
An octet string expressed as 'sddd.dd Centigrade' where:
s is the sign ('-' for negative or blank space for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Temperature' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CtemperatureCPU1WarningReset | 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.8 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The blade CPU warning reset temperature in degrees
centigrade(C). If the temperature rises above this value and
if a warning alert/event had previously been created then the
alert/event will be reset.
An octet string expressed as 'sddd.dd Centigrade' where:
s is the sign ('-' for negative or blank space for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Temperature' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CtemperatureCPU2HardShutdown | 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.9 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The blade CPU hard shutdown temperature in degrees
centigrade(C). If the component's temperature rises above
this value the system will be powered off immediately.
If enabled, a critical alert/event will be generated.
An octet string expressed as 'sddd.dd Centigrade' where:
s is the sign ('-' for negative or blank space for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Temperature' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CtemperatureCPU2Warning | 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.10 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The blade CPU warning temperature in degrees centigrade(C).
If the temperature rises above this value a warning alert/event
if enabled will be generated.
An octet string expressed as 'sddd.dd Centigrade' where:
s is the sign ('-' for negative or blank space for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Temperature' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CtemperatureCPU2WarningReset | 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.11 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The blade CPU warning reset temperature in degrees
centigrade(C). If the temperature rises above this value and
if a warning alert/event had previously been created then the
alert/event will be reset.
An octet string expressed as 'sddd.dd Centigrade' where:
s is the sign ('-' for negative or blank space for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Temperature' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CtemperatureCPU3HardShutdown | 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.12 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The blade CPU hard shutdown temperature in degrees
centigrade(C). If the component's temperature rises above
this value the system will be powered off immediately.
If enabled, a critical alert/event will be generated.
An octet string expressed as 'sddd.dd Centigrade' where:
s is the sign ('-' for negative or blank space for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Temperature' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CtemperatureCPU3Warning | 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.13 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The blade CPU warning temperature in degrees centigrade(C).
If the temperature rises above this value a warning alert/event
if enabled will be generated.
An octet string expressed as 'sddd.dd Centigrade' where:
s is the sign ('-' for negative or blank space for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Temperature' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CtemperatureCPU3WarningReset | 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.14 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The blade CPU warning reset temperature in degrees
centigrade(C). If the temperature rises above this value and
if a warning alert/event had previously been created then the
alert/event will be reset.
An octet string expressed as 'sddd.dd Centigrade' where:
s is the sign ('-' for negative or blank space for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Temperature' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CtemperatureCPU4HardShutdown | 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.15 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The blade CPU hard shutdown temperature in degrees
centigrade(C). If the component's temperature rises above
this value the system will be powered off immediately.
If enabled, a critical alert/event will be generated.
An octet string expressed as 'sddd.dd Centigrade' where:
s is the sign ('-' for negative or blank space for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Temperature' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CtemperatureCPU4Warning | 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.16 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The blade CPU warning temperature in degrees centigrade(C).
If the temperature rises above this value a warning alert/event
if enabled will be generated.
An octet string expressed as 'sddd.dd Centigrade' where:
s is the sign ('-' for negative or blank space for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Temperature' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CtemperatureCPU4WarningReset | 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.17 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The blade CPU warning reset temperature in degrees
centigrade(C). If the temperature rises above this value and
if a warning alert/event had previously been created then the
alert/event will be reset.
An octet string expressed as 'sddd.dd Centigrade' where:
s is the sign ('-' for negative or blank space for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Temperature' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CtemperatureDASD1HardShutdown | 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.18 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The blade DASD hard shutdown temperature in degrees centigrade(C).
An octet string expressed as 'sddd.dd Centigrade' where:
s is the sign ('-' for negative or blank space for positive)
d is a decimal digit or blank space for leading zeroes.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Temperature' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CtemperatureDASD1Warning | 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.19 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The blade DASD warning temperature in degrees centigrade(C).
An octet string expressed as 'sddd.dd Centigrade' where:
s is the sign ('-' for negative or blank space for positive)
d is a decimal digit or blank space for leading zeroes.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Temperature' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CtemperatureDASD1WarningReset | 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.20 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The blade DASD warning reset temperature in degrees centigrade(C).
An octet string expressed as 'sddd.dd Centigrade' where:
s is the sign ('-' for negative or blank space for positive)
d is a decimal digit or blank space for leading zeroes.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Temperature' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeTempThresholdSensorCapability | 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.21 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether the server blade is IPMI capable or not.
| ||||
| CtemperatureSensor1HardShutdown | 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.22 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The blade hard shutdown temperature for IPMI blades in degrees centigrade(C).
An octet string expressed as 'sddd.dd Centigrade' where:
s is the sign ('-' for negative or blank space for positive)
d is a decimal digit or blank space for leading zeroes.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Temperature' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CtemperatureSensor1Warning | 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.23 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The blade hard shutdown temperature for IPMI blades in degrees centigrade(C).
An octet string expressed as 'sddd.dd Centigrade' where:
s is the sign ('-' for negative or blank space for positive)
d is a decimal digit or blank space for leading zeroes.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Temperature' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CtemperatureSensor1WarningReset | 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.24 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The blade hard shutdown temperature for IPMI blades in degrees centigrade(C).
An octet string expressed as 'sddd.dd Centigrade' where:
s is the sign ('-' for negative or blank space for positive)
d is a decimal digit or blank space for leading zeroes.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Temperature' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CtemperatureSensor2HardShutdown | 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.25 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The blade hard shutdown temperature for IPMI blades in degrees centigrade(C).
An octet string expressed as 'sddd.dd Centigrade' where:
s is the sign ('-' for negative or blank space for positive)
d is a decimal digit or blank space for leading zeroes.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Temperature' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CtemperatureSensor2Warning | 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.26 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The blade hard shutdown temperature for IPMI blades in degrees centigrade(C).
An octet string expressed as 'sddd.dd Centigrade' where:
s is the sign ('-' for negative or blank space for positive)
d is a decimal digit or blank space for leading zeroes.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Temperature' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CtemperatureSensor2WarningReset | 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.27 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The blade hard shutdown temperature for IPMI blades in degrees centigrade(C).
An octet string expressed as 'sddd.dd Centigrade' where:
s is the sign ('-' for negative or blank space for positive)
d is a decimal digit or blank space for leading zeroes.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Temperature' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CtemperatureSensor3HardShutdown | 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.28 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The blade hard shutdown temperature for IPMI blades in degrees centigrade(C).
An octet string expressed as 'sddd.dd Centigrade' where:
s is the sign ('-' for negative or blank space for positive)
d is a decimal digit or blank space for leading zeroes.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Temperature' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CtemperatureSensor3Warning | 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.29 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The blade hard shutdown temperature for IPMI blades in degrees centigrade(C).
An octet string expressed as 'sddd.dd Centigrade' where:
s is the sign ('-' for negative or blank space for positive)
d is a decimal digit or blank space for leading zeroes.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Temperature' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CtemperatureSensor3WarningReset | 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.30 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The blade hard shutdown temperature for IPMI blades in degrees centigrade(C).
An octet string expressed as 'sddd.dd Centigrade' where:
s is the sign ('-' for negative or blank space for positive)
d is a decimal digit or blank space for leading zeroes.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Temperature' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CtemperatureSensor4HardShutdown | 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.31 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The blade hard shutdown temperature for IPMI blades in degrees centigrade(C).
An octet string expressed as 'sddd.dd Centigrade' where:
s is the sign ('-' for negative or blank space for positive)
d is a decimal digit or blank space for leading zeroes.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Temperature' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CtemperatureSensor4Warning | 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.32 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The blade hard shutdown temperature for IPMI blades in degrees centigrade(C).
An octet string expressed as 'sddd.dd Centigrade' where:
s is the sign ('-' for negative or blank space for positive)
d is a decimal digit or blank space for leading zeroes.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Temperature' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CtemperatureSensor4WarningReset | 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.33 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The blade hard shutdown temperature for IPMI blades in degrees centigrade(C).
An octet string expressed as 'sddd.dd Centigrade' where:
s is the sign ('-' for negative or blank space for positive)
d is a decimal digit or blank space for leading zeroes.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Temperature' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CtemperatureSensor5HardShutdown | 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.34 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The blade hard shutdown temperature for IPMI blades in degrees centigrade(C).
An octet string expressed as 'sddd.dd Centigrade' where:
s is the sign ('-' for negative or blank space for positive)
d is a decimal digit or blank space for leading zeroes.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Temperature' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CtemperatureSensor5Warning | 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.35 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The blade hard shutdown temperature for IPMI blades in degrees centigrade(C).
An octet string expressed as 'sddd.dd Centigrade' where:
s is the sign ('-' for negative or blank space for positive)
d is a decimal digit or blank space for leading zeroes.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Temperature' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CtemperatureSensor5WarningReset | 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.36 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The blade hard shutdown temperature for IPMI blades in degrees centigrade(C).
An octet string expressed as 'sddd.dd Centigrade' where:
s is the sign ('-' for negative or blank space for positive)
d is a decimal digit or blank space for leading zeroes.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Temperature' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CtemperatureSensor6HardShutdown | 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.37 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The blade hard shutdown temperature for IPMI blades in degrees centigrade(C).
An octet string expressed as 'sddd.dd Centigrade' where:
s is the sign ('-' for negative or blank space for positive)
d is a decimal digit or blank space for leading zeroes.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Temperature' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CtemperatureSensor6Warning | 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.38 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The blade hard shutdown temperature for IPMI blades in degrees centigrade(C).
An octet string expressed as 'sddd.dd Centigrade' where:
s is the sign ('-' for negative or blank space for positive)
d is a decimal digit or blank space for leading zeroes.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Temperature' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CtemperatureSensor6WarningReset | 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.39 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The blade hard shutdown temperature for IPMI blades in degrees centigrade(C).
An octet string expressed as 'sddd.dd Centigrade' where:
s is the sign ('-' for negative or blank space for positive)
d is a decimal digit or blank space for leading zeroes.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Temperature' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CtemperatureSensor7HardShutdown | 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.40 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The blade hard shutdown temperature for IPMI blades in degrees centigrade(C).
An octet string expressed as 'sddd.dd Centigrade' where:
s is the sign ('-' for negative or blank space for positive)
d is a decimal digit or blank space for leading zeroes.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Temperature' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CtemperatureSensor7Warning | 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.41 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The blade hard shutdown temperature for IPMI blades in degrees centigrade(C).
An octet string expressed as 'sddd.dd Centigrade' where:
s is the sign ('-' for negative or blank space for positive)
d is a decimal digit or blank space for leading zeroes.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Temperature' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CtemperatureSensor7WarningReset | 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.42 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The blade hard shutdown temperature for IPMI blades in degrees centigrade(C).
An octet string expressed as 'sddd.dd Centigrade' where:
s is the sign ('-' for negative or blank space for positive)
d is a decimal digit or blank space for leading zeroes.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Temperature' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CtemperatureSensor8HardShutdown | 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.43 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The blade hard shutdown temperature for IPMI blades in degrees centigrade(C).
An octet string expressed as 'sddd.dd Centigrade' where:
s is the sign ('-' for negative or blank space for positive)
d is a decimal digit or blank space for leading zeroes.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Temperature' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CtemperatureSensor8Warning | 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.44 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The blade hard shutdown temperature for IPMI blades in degrees centigrade(C).
An octet string expressed as 'sddd.dd Centigrade' where:
s is the sign ('-' for negative or blank space for positive)
d is a decimal digit or blank space for leading zeroes.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Temperature' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CtemperatureSensor8WarningReset | 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.45 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The blade hard shutdown temperature for IPMI blades in degrees centigrade(C).
An octet string expressed as 'sddd.dd Centigrade' where:
s is the sign ('-' for negative or blank space for positive)
d is a decimal digit or blank space for leading zeroes.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Temperature' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CtemperatureSensor9HardShutdown | 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.46 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The blade hard shutdown temperature for IPMI blades in degrees centigrade(C).
An octet string expressed as 'sddd.dd Centigrade' where:
s is the sign ('-' for negative or blank space for positive)
d is a decimal digit or blank space for leading zeroes.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Temperature' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CtemperatureSensor9Warning | 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.47 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The blade hard shutdown temperature for IPMI blades in degrees centigrade(C).
An octet string expressed as 'sddd.dd Centigrade' where:
s is the sign ('-' for negative or blank space for positive)
d is a decimal digit or blank space for leading zeroes.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Temperature' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CtemperatureSensor9WarningReset | 1.3.6.1.4.1.2.3.51.2.22.1.5.4.1.48 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The blade hard shutdown temperature for IPMI blades in degrees centigrade(C).
An octet string expressed as 'sddd.dd Centigrade' where:
s is the sign ('-' for negative or blank space for positive)
d is a decimal digit or blank space for leading zeroes.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Temperature' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| TbladeVoltagesTable | 1.3.6.1.4.1.2.3.51.2.22.1.5.5 | NA | mandatory | |
table · not-accessible · mandatory Table of blade voltages information. | ||||
| RbladeVoltagesEntry | 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1 | NA | mandatory | |
| CvoltageIndex | 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Blade voltages table index. | ||||
| CvoltageBladeId | 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The numeric blade ID.
| ||||
| CvoltageBladeExists | 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether the server blade specified exists or not.
| ||||
| CvoltageBladePowerState | 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates the power state of the blade specified.
| ||||
| CvoltageBladeName | 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.5 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The name of the blade as a null terminated string. | ||||
| CbladePlus5Volt | 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.6 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory +5 Volt power supply voltage reading for the blade
expressed in Volts(V). An octet string expressed as
'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladePlus3pt3Volt | 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.7 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory +3.3 Volt power supply voltage reading for the blade
expressed in Volts(V). An octet string expressed as
'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladePlus12Volt | 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.8 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory +12 Volt power supply voltage reading for the blade
expressed in Volts(V). An octet string expressed as
'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladePlus2pt5Volt | 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.10 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory +2.5 Volt power supply voltage reading for the blade
expressed in Volts(V). An octet string expressed as
'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladePlus1pt5Volt | 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.11 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory +1.5 Volt power supply voltage reading for the blade
expressed in Volts(V). An octet string expressed as
'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladePlus1pt25Volt | 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.12 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory +1.25 Volt power supply voltage reading for the blade
expressed in Volts(V). An octet string expressed as
'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeVRM1Volt | 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.13 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory VRM 1 voltage reading for the blade expressed in Volts(V).
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensorVoltCapability | 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.14 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether the server blade is IPMI capable or not.
| ||||
| CbladeSensor1Volt | 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.15 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage reading for an IPMI blade expressed in Volts(V).
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor2Volt | 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.16 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage reading for an IPMI blade expressed in Volts(V).
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor3Volt | 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.17 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage reading for an IPMI blade expressed in Volts(V).
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor4Volt | 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.18 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage reading for an IPMI blade expressed in Volts(V).
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor5Volt | 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.19 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage reading for an IPMI blade expressed in Volts(V).
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor6Volt | 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.20 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage reading for an IPMI blade expressed in Volts(V).
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor7Volt | 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.21 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage reading for an IPMI blade expressed in Volts(V).
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor8Volt | 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.22 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage reading for an IPMI blade expressed in Volts(V).
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor9Volt | 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.23 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage reading for an IPMI blade expressed in Volts(V).
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor10Volt | 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.24 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage reading for an IPMI blade expressed in Volts(V).
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor11Volt | 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.25 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage reading for an IPMI blade expressed in Volts(V).
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor12Volt | 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.26 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage reading for an IPMI blade expressed in Volts(V).
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor13Volt | 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.27 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage reading for an IPMI blade expressed in Volts(V).
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor14Volt | 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.28 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage reading for an IPMI blade expressed in Volts(V).
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor15Volt | 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.29 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage reading for an IPMI blade expressed in Volts(V).
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor16Volt | 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.30 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage reading for an IPMI blade expressed in Volts(V).
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor17Volt | 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.31 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage reading for an IPMI blade expressed in Volts(V).
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor18Volt | 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.32 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage reading for an IPMI blade expressed in Volts(V).
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor19Volt | 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.33 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage reading for an IPMI blade expressed in Volts(V).
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor20Volt | 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.34 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage reading for an IPMI blade expressed in Volts(V).
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor21Volt | 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.35 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage reading for an IPMI blade expressed in Volts(V).
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor22Volt | 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.36 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage reading for an IPMI blade expressed in Volts(V).
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor23Volt | 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.37 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage reading for an IPMI blade expressed in Volts(V).
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor24Volt | 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.38 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage reading for an IPMI blade expressed in Volts(V).
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor25Volt | 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.39 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage reading for an IPMI blade expressed in Volts(V).
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor26Volt | 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.40 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage reading for an IPMI blade expressed in Volts(V).
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor27Volt | 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.41 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage reading for an IPMI blade expressed in Volts(V).
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor28Volt | 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.42 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage reading for an IPMI blade expressed in Volts(V).
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor29Volt | 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.43 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage reading for an IPMI blade expressed in Volts(V).
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor30Volt | 1.3.6.1.4.1.2.3.51.2.22.1.5.5.1.44 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage reading for an IPMI blade expressed in Volts(V).
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| TbladeVoltageThresholdsTable | 1.3.6.1.4.1.2.3.51.2.22.1.5.6 | NA | mandatory | |
table · not-accessible · mandatory Table of blade VoltageThresholds information. | ||||
| RbladeVoltageThresholdsEntry | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1 | NA | mandatory | |
| CvoltageThresholdIndex | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Blade voltage thresholds table index. | ||||
| CvoltageThresholdBladeId | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The numeric blade ID.
| ||||
| CvoltageThresholdBladeExists | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether the server blade specified exists or not.
| ||||
| CvoltageThresholdBladePowerState | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates the power state of the blade specified.
| ||||
| CvoltageThresholdBladeName | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.5 | OCTET STRING | RW | mandatory |
column · OCTET STRING · read-write · mandatory The name of the blade as a null terminated string. | ||||
| CbladePlus5VoltHighWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.6 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading expressed in Volts(V).
If the voltage rises above this value a warning alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladePlus5VoltLowWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.7 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading expressed in Volts(V).
If the voltage drops below this value a warning alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladePlus3pt3VoltHighWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.8 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading expressed in Volts(V).
If the voltage rises above this value a warning alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladePlus3pt3VoltLowWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.9 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading expressed in Volts(V).
If the voltage drops below this value a warning alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladePlus12VoltHighWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.10 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading expressed in Volts(V).
If the voltage rises above this value a warning alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladePlus12VoltLowWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.11 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading expressed in Volts(V).
If the voltage drops below this value a warning alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladePlus2pt5VoltHighWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.14 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading expressed in Volts(V).
If the voltage rises above this value a warning alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladePlus2pt5VoltLowWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.15 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading expressed in Volts(V).
If the voltage drops below this value a warning alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladePlus1pt5VoltHighWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.16 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading expressed in Volts(V).
If the voltage rises above this value a warning alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladePlus1pt5VoltLowWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.17 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading expressed in Volts(V).
If the voltage drops below this value a warning alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladePlus1pt25VoltHighWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.18 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading expressed in Volts(V).
If the voltage rises above this value a warning alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladePlus1pt25VoltLowWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.19 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading expressed in Volts(V).
If the voltage drops below this value a warning alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeVoltThresholdSensorCapability | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.22 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether the server blade is IPMI capable or not.
| ||||
| CbladeSensor1VoltHighWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.23 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading for IPMI blades expressed in Volts(V).
If the voltage rises above this value, a critical alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor1VoltLowWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.24 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading for IPMI blades expressed in Volts(V).
If the voltage drops below this value, a critical alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor2VoltHighWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.25 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading for IPMI blades expressed in Volts(V).
If the voltage rises above this value, a critical alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor2VoltLowWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.26 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading for IPMI blades expressed in Volts(V).
If the voltage drops below this value, a critical alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor3VoltHighWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.27 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading for IPMI blades expressed in Volts(V).
If the voltage rises above this value, a critical alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor3VoltLowWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.28 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading for IPMI blades expressed in Volts(V).
If the voltage drops below this value, a critical alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor4VoltHighWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.29 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading for IPMI blades expressed in Volts(V).
If the voltage rises above this value, a critical alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor4VoltLowWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.30 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading for IPMI blades expressed in Volts(V).
If the voltage drops below this value, a critical alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor5VoltHighWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.31 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading for IPMI blades expressed in Volts(V).
If the voltage rises above this value, a critical alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor5VoltLowWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.32 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading for IPMI blades expressed in Volts(V).
If the voltage drops below this value, a critical alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor6VoltHighWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.33 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading for IPMI blades expressed in Volts(V).
If the voltage rises above this value, a critical alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor6VoltLowWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.34 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading for IPMI blades expressed in Volts(V).
If the voltage drops below this value, a critical alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor7VoltHighWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.35 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading for IPMI blades expressed in Volts(V).
If the voltage rises above this value, a critical alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor7VoltLowWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.36 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading for IPMI blades expressed in Volts(V).
If the voltage drops below this value, a critical alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor8VoltHighWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.37 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading for IPMI blades expressed in Volts(V).
If the voltage rises above this value, a critical alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor8VoltLowWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.38 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading for IPMI blades expressed in Volts(V).
If the voltage drops below this value, a critical alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor9VoltHighWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.39 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading for IPMI blades expressed in Volts(V).
If the voltage rises above this value, a critical alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor9VoltLowWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.40 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading for IPMI blades expressed in Volts(V).
If the voltage drops below this value, a critical alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor10VoltHighWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.41 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading for IPMI blades expressed in Volts(V).
If the voltage rises above this value, a critical alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor10VoltLowWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.42 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading for IPMI blades expressed in Volts(V).
If the voltage drops below this value, a critical alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor11VoltHighWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.43 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading for IPMI blades expressed in Volts(V).
If the voltage rises above this value, a critical alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor11VoltLowWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.44 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading for IPMI blades expressed in Volts(V).
If the voltage drops below this value, a critical alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor12VoltHighWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.45 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading for IPMI blades expressed in Volts(V).
If the voltage rises above this value, a critical alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor12VoltLowWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.46 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading for IPMI blades expressed in Volts(V).
If the voltage drops below this value, a critical alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor13VoltHighWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.47 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading for IPMI blades expressed in Volts(V).
If the voltage rises above this value, a critical alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor13VoltLowWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.48 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading for IPMI blades expressed in Volts(V).
If the voltage drops below this value, a critical alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor14VoltHighWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.49 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading for IPMI blades expressed in Volts(V).
If the voltage rises above this value, a critical alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor14VoltLowWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.50 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading for IPMI blades expressed in Volts(V).
If the voltage drops below this value, a critical alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor15VoltHighWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.51 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading for IPMI blades expressed in Volts(V).
If the voltage rises above this value, a critical alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor15VoltLowWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.52 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading for IPMI blades expressed in Volts(V).
If the voltage drops below this value, a critical alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor16VoltHighWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.53 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading for IPMI blades expressed in Volts(V).
If the voltage rises above this value, a critical alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor16VoltLowWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.54 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading for IPMI blades expressed in Volts(V).
If the voltage drops below this value, a critical alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor17VoltHighWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.55 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading for IPMI blades expressed in Volts(V).
If the voltage rises above this value, a critical alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor17VoltLowWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.56 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading for IPMI blades expressed in Volts(V).
If the voltage drops below this value, a critical alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor18VoltHighWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.57 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading for IPMI blades expressed in Volts(V).
If the voltage rises above this value, a critical alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor18VoltLowWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.58 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading for IPMI blades expressed in Volts(V).
If the voltage drops below this value, a critical alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor19VoltHighWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.59 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading for IPMI blades expressed in Volts(V).
If the voltage rises above this value, a critical alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor19VoltLowWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.60 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading for IPMI blades expressed in Volts(V).
If the voltage drops below this value, a critical alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor20VoltHighWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.61 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading for IPMI blades expressed in Volts(V).
If the voltage rises above this value, a critical alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor20VoltLowWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.62 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading for IPMI blades expressed in Volts(V).
If the voltage drops below this value, a critical alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor21VoltHighWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.63 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading for IPMI blades expressed in Volts(V).
If the voltage rises above this value, a critical alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor21VoltLowWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.64 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading for IPMI blades expressed in Volts(V).
If the voltage drops below this value, a critical alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor22VoltHighWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.65 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading for IPMI blades expressed in Volts(V).
If the voltage rises above this value, a critical alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor22VoltLowWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.66 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading for IPMI blades expressed in Volts(V).
If the voltage drops below this value, a critical alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor23VoltHighWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.67 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading for IPMI blades expressed in Volts(V).
If the voltage rises above this value, a critical alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor23VoltLowWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.68 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading for IPMI blades expressed in Volts(V).
If the voltage drops below this value, a critical alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor24VoltHighWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.69 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading for IPMI blades expressed in Volts(V).
If the voltage rises above this value, a critical alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor24VoltLowWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.70 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading for IPMI blades expressed in Volts(V).
If the voltage drops below this value, a critical alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor25VoltHighWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.71 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading for IPMI blades expressed in Volts(V).
If the voltage rises above this value, a critical alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor25VoltLowWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.72 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading for IPMI blades expressed in Volts(V).
If the voltage drops below this value, a critical alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor26VoltHighWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.73 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading for IPMI blades expressed in Volts(V).
If the voltage rises above this value, a critical alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor26VoltLowWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.74 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading for IPMI blades expressed in Volts(V).
If the voltage drops below this value, a critical alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor27VoltHighWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.75 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading for IPMI blades expressed in Volts(V).
If the voltage rises above this value, a critical alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor27VoltLowWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.76 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading for IPMI blades expressed in Volts(V).
If the voltage drops below this value, a critical alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor28VoltHighWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.77 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading for IPMI blades expressed in Volts(V).
If the voltage rises above this value, a critical alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor28VoltLowWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.78 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading for IPMI blades expressed in Volts(V).
If the voltage drops below this value, a critical alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor29VoltHighWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.79 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading for IPMI blades expressed in Volts(V).
If the voltage rises above this value, a critical alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor29VoltLowWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.80 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading for IPMI blades expressed in Volts(V).
If the voltage drops below this value, a critical alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor30VoltHighWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.81 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading for IPMI blades expressed in Volts(V).
If the voltage rises above this value, a critical alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| CbladeSensor30VoltLowWarning | 1.3.6.1.4.1.2.3.51.2.22.1.5.6.1.82 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Voltage warning threshold reading for IPMI blades expressed in Volts(V).
If the voltage drops below this value, a critical alert/event
if enabled will be generated.
An octet string expressed as 'sdd.dd Volts' where:
s is the sign ('-' for negative or '+' for positive)
d is a decimal digit or blank space for a leading zero.
The string 'Not Readable!' indicates that the given monitor
is not supported on this system.
The string 'No Voltage' indicates that the given monitor
does not exist on this system or is powered off. | ||||
| NbladePowerRestart | 1.3.6.1.4.1.2.3.51.2.22.1.6 | |||
| TbladePowerRestartTable | 1.3.6.1.4.1.2.3.51.2.22.1.6.1 | NA | mandatory | |
table · not-accessible · mandatory Table of blade remote power control information. Contains power on/off enablement status for each blade. | ||||
| RbladePowerRestartEntry | 1.3.6.1.4.1.2.3.51.2.22.1.6.1.1 | NA | mandatory | |
| CpowerRestartIndex | 1.3.6.1.4.1.2.3.51.2.22.1.6.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Blade power restart table index. | ||||
| CpowerRestartBladeId | 1.3.6.1.4.1.2.3.51.2.22.1.6.1.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The numeric blade ID.
| ||||
| CpowerRestartBladeExists | 1.3.6.1.4.1.2.3.51.2.22.1.6.1.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether the server blade specified exists or not.
| ||||
| CpowerRestartBladePowerState | 1.3.6.1.4.1.2.3.51.2.22.1.6.1.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates the power state of the blade specified. If the state cannot be determined, the unknown(255) is returned.
| ||||
| CpowerRestartBladeHealthState | 1.3.6.1.4.1.2.3.51.2.22.1.6.1.1.5 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The system health state for the blade. Unknown: Blade is in an undefined state. Good: Blade is operating normally. Warning: One or more outstanding warnings exist for this blade. Critical: One or more outstanding critical events for this blade. Kernel Mode: Blade is in kernel mode. Discovering: The MM is currently in the process of discovering this blade. Communications Error: The MM failed to communicate with this blade. No Power: No power to the blade's domain. Flashing: Flashing in progress. Initialization Failure: Blade failed to initialized. Insufficient Power: Not enough power is left in the blade's domain to power the blade. Power Denied: Power was denied to the blade.
| ||||
| CpowerRestartBladeName | 1.3.6.1.4.1.2.3.51.2.22.1.6.1.1.6 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The name of the blade as a null terminated string. | ||||
| CpowerOnOffBlade | 1.3.6.1.4.1.2.3.51.2.22.1.6.1.1.7 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Control the power state of a specific blade.
Off: Power Off Blade.
On: Power On Blade.
Softoff: Shut Down OS and Power Off Blade. This operation is not
supported on all blades.
NOTE: Value returned for the GET command is meaningless
for this MIB object. The powerRestartBladePowerState MIB object should be
used to check the power state of the blade(s)
| ||||
| CrestartBlade | 1.3.6.1.4.1.2.3.51.2.22.1.6.1.1.8 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Restart a blade. NOTE: Value returned for the GET command is meaningless for this MIB object.
| ||||
| CrestartBladeSMP | 1.3.6.1.4.1.2.3.51.2.22.1.6.1.1.9 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Restart a blade's system management processor. NOTE: Value returned for the GET command is meaningless for this MIB object.
| ||||
| CrestartBladeNMI | 1.3.6.1.4.1.2.3.51.2.22.1.6.1.1.10 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Issue an NMI to the blade. This option is not supported on all blades. NOTE: Value returned for the GET command is meaningless for this MIB object.
| ||||
| CrestartBladeClearNVRAM | 1.3.6.1.4.1.2.3.51.2.22.1.6.1.1.11 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Restart a blade and set NVRAM to default values. This option is not supported on all blades. NOTE: Value returned for the GET command is meaningless for this MIB object.
| ||||
| CrestartBladeInvokeDiags | 1.3.6.1.4.1.2.3.51.2.22.1.6.1.1.12 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Restart a blade and boot into diagnostic mode. This option is not supported on all blades. NOTE: Value returned for the GET command is meaningless for this MIB object.
| ||||
| CrestartBladeInvokeDiagsFromDefaultBootList | 1.3.6.1.4.1.2.3.51.2.22.1.6.1.1.13 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Restart a blade and boot into diagnostic mode from Default Boot List as defined on the blade. This option is not supported on all blades. NOTE: Value returned for the GET command is meaningless for this MIB object.
| ||||
| CrestartBladeToSMSBootMenu | 1.3.6.1.4.1.2.3.51.2.22.1.6.1.1.14 | INTEGER | RW | deprecated |
column · INTEGER · read-write · deprecated Restart a blade to SMS boot menu. This option is not supported on all blades, and at the time of this MIB definition was only supported on POWER blades. This object is deprecated and please use the bladePowerEnableSMSBootMenu object. NOTE: Value returned for the GET command is meaningless for this MIB object.
| ||||
| CbladePowerEnableSMSBootMenu | 1.3.6.1.4.1.2.3.51.2.22.1.6.1.1.15 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Enables/disables a blade restart to the SMS boot menu. Setting this object to 'enable(1)' will cause a reboot of the node to the SMS menu. This option is not supported by all blades, and at the time of this MIB definition was only supported on POWER blades.
| ||||
| NbladeConfiguration | 1.3.6.1.4.1.2.3.51.2.22.1.7 | |||
| TbladeConfigurationTable | 1.3.6.1.4.1.2.3.51.2.22.1.7.1 | NA | mandatory | |
table · not-accessible · mandatory Table of blade configuration information. Contains boot mode and auto power on/off settings for each blade. | ||||
| RbladeConfigurationEntry | 1.3.6.1.4.1.2.3.51.2.22.1.7.1.1 | NA | mandatory | |
| CconfigurationIndex | 1.3.6.1.4.1.2.3.51.2.22.1.7.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Blade configuration table index. | ||||
| CconfigurationBladeId | 1.3.6.1.4.1.2.3.51.2.22.1.7.1.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The numeric blade ID.
| ||||
| CconfigurationBladeExists | 1.3.6.1.4.1.2.3.51.2.22.1.7.1.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether the server blade specified exists or not.
| ||||
| CconfigurationBladePowerState | 1.3.6.1.4.1.2.3.51.2.22.1.7.1.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates the power state of the blade specified.
| ||||
| CconfigurationBladeName | 1.3.6.1.4.1.2.3.51.2.22.1.7.1.1.5 | OCTET STRING | RW | mandatory |
column · OCTET STRING · read-write · mandatory The name of the blade as a null terminated string. | ||||
| CconfigurationBladeActiveBootMode | 1.3.6.1.4.1.2.3.51.2.22.1.7.1.1.7 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates the active copy of the firmware from which the blade is booting. NOTE: Some blades do not support the automatic boot recovery. It displays 'notApplicable' for such blades. Booting from the temporary copy is recommended since it typically contains the latest enhancements and fixes. Switching to the permanent copy should be reserved for when booting from the temporary copy is no longer possible.
| ||||
| CconfigurationBladePendingBootMode | 1.3.6.1.4.1.2.3.51.2.22.1.7.1.1.8 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Indicates the copy of the firmware from which the blade will boot after the next reboot. NOTE: Some blades do not support the automatic boot recovery. It displays 'notApplicable' for such blades and the value can not be set. Booting from the temporary copy is recommended since it typically contains the latest enhancements and fixes. Switching to the permanent copy should be reserved for when booting from the temporary copy is no longer possible.
| ||||
| CconfigurationBladeAutoPowerOn | 1.3.6.1.4.1.2.3.51.2.22.1.7.1.1.9 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Blade auto-power on policy. - restore: blade will be powered on which were previously on. - auto: blade will automatically be powered on when power is applied to the chassis. - manual: blade will be left off until manually powered on by the user. - notApplicable: is a read-only value, this value cannot be set.
| ||||
| CconfigurationBladePowerOnRestartDelay | 1.3.6.1.4.1.2.3.51.2.22.1.7.1.1.10 | INTEGER (0..32767) | RW | mandatory |
column · INTEGER (0..32767) · read-write · mandatory Restart delay (in seconds) when power is applied to a blade. | ||||
| NbladePowerManagementPolicy | 1.3.6.1.4.1.2.3.51.2.22.1.7.2 | |||
| SpowerManagementPolicy | 1.3.6.1.4.1.2.3.51.2.22.1.7.2.1 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Power Module Redundancy Intended for a single power source into the chassis where each Power Module is on its own dedicated circuit. Maximum power is limited to one less than the number of Power Modules when more than one Power Module is present. One Power Module can fail without affecting compute node operation. Multiple Power Module failures can cause the chassis to power off. Note that some compute nodes may not be allowed to power on if doing so would exceed the policy power limit. Power Module Redundancy with Compute Nodes Throttling Allowed Very similar to Power Module Redundancy. This policy allows for a higher power limit; however, capable compute nodes may be allowed to throttle down if one Power Module fails. Basic Power Management Maximum power limit is higher than other policies and is limited only by the nameplate power of all the Power Modules combined. This is the least conservative approach, since it does not provide any protection for power source or Power Module failure. If any single power supply fails, compute node and/or chassis operation may be affected. Power Source Redundancy Intended for dual power sources into the chassis. Maximum power is limited to the capacity of half the number of installed power modules. This is the most conservative approach and is recommended when all power modules are installed. When the chassis is correctly wired with dual power sources, one power source can fail without affecting compute node server operation. Note that some compute nodes may not be allowed to power on if doing so would exceed the policy power limit. Power Source Redundancy with Compute Node Throttling Allowed Very similar to the Power Source Redundancy. This policy allows for a higher power limit, however capable compute nodes may be allowed to throttle down if one power source fails. Please see the powerPolicyTable for more information regarding this setting.
| ||||
| SacousticMode | 1.3.6.1.4.1.2.3.51.2.22.1.7.2.3 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Acoustic mode setting for thermal conditions. A setting of disabled (0), disables this feature. A setting of acoustic-quiet-level1 (5) is the least restrictive and the least quiet sound level. A setting of acoustic-quiet-level5 (1) is the most restrictive and the most quiet sound level. Some values may not be valid on some chassis. A bad value will be returned in this case.
| ||||
| NbladeBootCountPowerOnTime | 1.3.6.1.4.1.2.3.51.2.22.1.10 | |||
| TbladeBootCountPowerOnTimeTable | 1.3.6.1.4.1.2.3.51.2.22.1.10.1 | NA | mandatory | |
table · not-accessible · mandatory Table per blade of the number of boots for the blade and the number of seconds the blade has been powered on. | ||||
| RbladeBootCountPowerOnTimeEntry | 1.3.6.1.4.1.2.3.51.2.22.1.10.1.1 | NA | mandatory | |
row · not-accessible · mandatory The number of boots for the blade and the number of seconds the blade has been powered on. | ||||
| CbootCountPowerOnTimeBladeIndex | 1.3.6.1.4.1.2.3.51.2.22.1.10.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Blade boot count/Power On Time table index. | ||||
| CbootCountPowerOnTimeBladeId | 1.3.6.1.4.1.2.3.51.2.22.1.10.1.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The numeric blade ID.
| ||||
| CbootCountPowerOnTimeBoots | 1.3.6.1.4.1.2.3.51.2.22.1.10.1.1.3 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Blade Boot Count. If there is no blade in the given slot then this value is undefined. Writing this value resets the Boot Count to zero. | ||||
| CbootCountPowerOnTimeSecs | 1.3.6.1.4.1.2.3.51.2.22.1.10.1.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Blade Power On Time in seconds. If there is no blade in the given slot then this value is undefined. Writing this value resets the Power On Time to zero. | ||||
| SbladeVlanId | 1.3.6.1.4.1.2.3.51.2.22.1.11 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory This is the virtual LAN ID for the internal management network between the MM and the blade system management processors (BSMPs). The range of valid VLAN ID's is 3 to 4095. | ||||
| NbladeNetworkConfiguration | 1.3.6.1.4.1.2.3.51.2.22.1.12 | |||
| TbladeIPv4ConfigTable | 1.3.6.1.4.1.2.3.51.2.22.1.12.5 | NA | mandatory | |
table · not-accessible · mandatory Table of all blades' network interfaces. | ||||
| RbladeIPv4ConfigEntry | 1.3.6.1.4.1.2.3.51.2.22.1.12.5.1 | NA | mandatory | |
row · not-accessible · mandatory Blade configuration table entry | ||||
| CbladeIPv4ConfigIndex | 1.3.6.1.4.1.2.3.51.2.22.1.12.5.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The blade's slot number. | ||||
| CbladeIPv4ConfigPortIndex | 1.3.6.1.4.1.2.3.51.2.22.1.12.5.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The physical port number of the given entry. | ||||
| CbladeIPv4ConfigPortLabel | 1.3.6.1.4.1.2.3.51.2.22.1.12.5.1.3 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Show string label that identifies the interface. | ||||
| CbladeIPv4ConfigPhysicalLinkStatus | 1.3.6.1.4.1.2.3.51.2.22.1.12.5.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether this network interface port is up or down. If this network interface doesn't support up/down, show 'notApplicable(255)'.
| ||||
| CbladeIPv4ConfigPhysicalLinkState | 1.3.6.1.4.1.2.3.51.2.22.1.12.5.1.5 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Configuration object for requesting the physical port to be either, down(0), up(1) or loopback(2). To get the current status of a physical port, use the object, bladeIPv4ConfigPhysicalLinkStatus. If this network interface doesn't support up/down/loopback, show 'notApplicable(255)'.
| ||||
| CbladeIPv4ConfigIPAddr | 1.3.6.1.4.1.2.3.51.2.22.1.12.5.1.6 | IpAddress | RW | mandatory |
column · IpAddress · read-write · mandatory Show/modify current IP address of the blade network interface. Note that only if the bladeIPv4ConfigPhysicalLinkStatus is 'up(1)' and the bladeIPv4ConfigDHCPEnable is not 'useDhcp(1)', should the IP address be pushed down to blade System Management Processor. | ||||
| CbladeIPv4ConfigSubnetMask | 1.3.6.1.4.1.2.3.51.2.22.1.12.5.1.7 | IpAddress | RW | mandatory |
column · IpAddress · read-write · mandatory Show or modifie current subnet mask of the blade network interface. Note that only if the bladeIPv4ConfigPhysicalLinkStatus is 'up(1)' and the bladeIPv4ConfigDHCPEnable is not 'useDhcp(1)', should the IP address be pushed down to blade System Management Processor. | ||||
| CbladeIPv4ConfigGatewayAddr | 1.3.6.1.4.1.2.3.51.2.22.1.12.5.1.8 | IpAddress | RW | mandatory |
column · IpAddress · read-write · mandatory Show or modify current IP gateway of the blade network interface. Note that only if the bladeIPv4ConfigPhysicalLinkStatus is 'up(1)' and the bladeIPv4ConfigDHCPEnable is not 'useDhcp(1)', should the IP address be pushed down to blade System Management Processor. | ||||
| CbladeIPv4ConfigVlanId | 1.3.6.1.4.1.2.3.51.2.22.1.12.5.1.9 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory This is the Virtual LAN ID for supported network interface cards (NICs). The range of valid VLAN ID's is 0 to 4095. | ||||
| CbladeIPv4ConfigDHCPEnable | 1.3.6.1.4.1.2.3.51.2.22.1.12.5.1.10 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory IP config method on the blade network interface to modify mode to static IP, DHCP and 'try DHCP then try static'. If this network interface doesn't support DHCP, show 'notApplicable(255)'.
| ||||
| CbladeIPv4ConfigMACAddr | 1.3.6.1.4.1.2.3.51.2.22.1.12.5.1.11 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Show the blade network interface MAC address. If this network interface doesn't support MAC, show 'notApplicable'. | ||||
| NbladeIPv6Config | 1.3.6.1.4.1.2.3.51.2.22.1.12.10 | |||
| TbladeIPv6ConfigTable | 1.3.6.1.4.1.2.3.51.2.22.1.12.10.1 | NA | mandatory | |
table · not-accessible · mandatory A table of IPv6 configuration options for blades. NOTE: This MIB object is not applicable to blades that do not support IPv6. | ||||
| RbladeIPv6ConfigEntry | 1.3.6.1.4.1.2.3.51.2.22.1.12.10.1.1 | NA | mandatory | |
row · not-accessible · mandatory IPv6 configuration options for a blade. NOTE: This MIB object is not applicable to blades that do not support IPv6. | ||||
| CbladeIPv6ConfigIndex | 1.3.6.1.4.1.2.3.51.2.22.1.12.10.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The blade's slot number | ||||
| CbladeIPv6ConfigPortIndex | 1.3.6.1.4.1.2.3.51.2.22.1.12.10.1.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The physical port number of the given entry | ||||
| CbladeIPv6ConfigEnabled | 1.3.6.1.4.1.2.3.51.2.22.1.12.10.1.1.3 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Enables/Disables IPv6 support on the blade.
| ||||
| CbladeIPv6ConfigStatic | 1.3.6.1.4.1.2.3.51.2.22.1.12.10.1.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Enables/Disables IPv6 static configuration support on the blade.
| ||||
| CbladeDHCPv6ConfigEnabled | 1.3.6.1.4.1.2.3.51.2.22.1.12.10.1.1.5 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Enables/Disables DHCPv6 address configuration support on the blade.
| ||||
| CbladeIPv6ConfigStatelessEnabled | 1.3.6.1.4.1.2.3.51.2.22.1.12.10.1.1.6 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Enables/Disables IPv6 stateless auto-configuration support on the blade.
| ||||
| TbladeIPv6AddressTable | 1.3.6.1.4.1.2.3.51.2.22.1.12.10.2 | NA | mandatory | |
table · not-accessible · mandatory A table of assigned IPv6 addresses for blades. NOTE: This MIB object is not applicable to blades that do not support IPv6. | ||||
| RbladeIPv6AddressEntry | 1.3.6.1.4.1.2.3.51.2.22.1.12.10.2.1 | NA | mandatory | |
row · not-accessible · mandatory The assigned IPv6 address for a given blade. NOTE: This MIB object is not applicable to blades that do not support IPv6. | ||||
| CbladeIPv6AddressIndex | 1.3.6.1.4.1.2.3.51.2.22.1.12.10.2.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The blade's slot number. | ||||
| CbladeIPv6AddressPortIndex | 1.3.6.1.4.1.2.3.51.2.22.1.12.10.2.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The blade's physical port number for the given entry. | ||||
| CbladeIPv6AddressEntryIndex | 1.3.6.1.4.1.2.3.51.2.22.1.12.10.2.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The blade's address entry index. | ||||
| CbladeIPv6AddressType | 1.3.6.1.4.1.2.3.51.2.22.1.12.10.2.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The address type.
| ||||
| CbladeIPv6Address | 1.3.6.1.4.1.2.3.51.2.22.1.12.10.2.1.5 | InetAddressIPv6 | RW | mandatory |
column · InetAddressIPv6 · read-write · mandatory The assigned IPv6 address. Note: 'write' is for static ipv6 only. | ||||
| CbladeIPv6AddressPrefixLen | 1.3.6.1.4.1.2.3.51.2.22.1.12.10.2.1.6 | INTEGER (1..128) | RW | mandatory |
column · INTEGER (1..128) · read-write · mandatory The prefix length for the given address. Note: 'write' is for static ipv6 only. | ||||
| CbladeIPv6AddressDefaultRoute | 1.3.6.1.4.1.2.3.51.2.22.1.12.10.2.1.7 | InetAddressIPv6 | RW | mandatory |
column · InetAddressIPv6 · read-write · mandatory The default route used for the given address. Note: 'write' is for static ipv6 only. | ||||
| TbladeBayDataTable | 1.3.6.1.4.1.2.3.51.2.22.1.13 | NA | mandatory | |
table · not-accessible · mandatory Table of blade bay data (BBD) information. | ||||
| RbladeBayDataEntry | 1.3.6.1.4.1.2.3.51.2.22.1.13.1 | NA | mandatory | |
| CbayDataIndex | 1.3.6.1.4.1.2.3.51.2.22.1.13.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Blade bay data (BBD) table index. | ||||
| CbayDataBladeId | 1.3.6.1.4.1.2.3.51.2.22.1.13.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The numeric blade ID.
| ||||
| CbayDataBladeExists | 1.3.6.1.4.1.2.3.51.2.22.1.13.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether the server blade specified exists or not.
| ||||
| CbayDataBladePowerState | 1.3.6.1.4.1.2.3.51.2.22.1.13.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates the power state of the blade specified.
| ||||
| CbayDataBladeName | 1.3.6.1.4.1.2.3.51.2.22.1.13.1.5 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The name of the blade as a null terminated string. | ||||
| CbayData | 1.3.6.1.4.1.2.3.51.2.22.1.13.1.6 | OCTET STRING | RW | mandatory |
column · OCTET STRING · read-write · mandatory A null terminated string that defines the Blade Bay Data (BBD). This data is pushed to the blade's BSMP and SMBIOS structures, where it can used by the blade's OS. Up to 60 characters can be defined plus a Null terminator. | ||||
| CbayDataBladeStatus | 1.3.6.1.4.1.2.3.51.2.22.1.13.1.7 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This shows Blade Bay Data (BBD) status. 0 means the blade fully supports BBD; 1 means that the blade's BIOS does not support BBD; 2 means that there is no blade in the bay; 3 means that the blade is being discovered. 255 means that the blade does not support BBD.
| ||||
| NbladeSPEthOverUSBInterface | 1.3.6.1.4.1.2.3.51.2.22.1.14 | |||
| TspEthOverUSBInterfaceTable | 1.3.6.1.4.1.2.3.51.2.22.1.14.1 | NA | mandatory | |
table · not-accessible · mandatory Table of blade Service Processor's Ethernet over USB interface. | ||||
| RspEthOverUSBInterfaceEntry | 1.3.6.1.4.1.2.3.51.2.22.1.14.1.1 | NA | mandatory | |
row · not-accessible · mandatory Blade Service Processor's Ethernet over USB interface entry. | ||||
| CspEthOverUSBInterfaceIndex | 1.3.6.1.4.1.2.3.51.2.22.1.14.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Service Processor's Ethernet over USB interface table index. | ||||
| CspEthOverUSBInterfaceBladeId | 1.3.6.1.4.1.2.3.51.2.22.1.14.1.1.2 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The numeric blade ID. | ||||
| CspEthOverUSBInterfaceBladeExists | 1.3.6.1.4.1.2.3.51.2.22.1.14.1.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether the blade specified exists or not.
| ||||
| CspEthOverUSBInterfaceBladeName | 1.3.6.1.4.1.2.3.51.2.22.1.14.1.1.6 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The name of the blade as a null terminated string. | ||||
| CspEthOverUSBInterfaceEnable | 1.3.6.1.4.1.2.3.51.2.22.1.14.1.1.9 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory This object allows the user to view the status of, and enable or disable, a blade Service Processor's command interface on Ethernet-over-USB. NOTE: If the blade either does not exist or does not support Ethernet-over-USB command interface. It displays 'notApplicable'. NOTE: It will take about 10 or more seconds for the disable/enable setting to take effect.
| ||||
| TbootDeviceInfoTable | 1.3.6.1.4.1.2.3.51.2.22.1.15 | NA | mandatory | |
table · not-accessible · mandatory Table of blade boot device information. Contains info for the boot devices for each blade. | ||||
| RbootDeviceInfoEntry | 1.3.6.1.4.1.2.3.51.2.22.1.15.1 | NA | mandatory | |
| CbootInfoTopologyIndex | 1.3.6.1.4.1.2.3.51.2.22.1.15.1.1 | OCTET STRING (SIZE (0..100)) | RO | mandatory |
column · OCTET STRING (SIZE (0..100)) · read-only · mandatory The unique identifier for a node containing boot devices in this table. The chassis and each installed component is represented by a hardware topology tree, where each node in the tree represents a component. The path to a particular component consists of one or more <component>,<instance> pairs, where each successive pair is a child of the previous parent pair. As an example, the root of the tree is the chassis and is represented by the pair 'CHASSIS, 1'. This pair indicates the first instance of the chassis. If a blade is inserted in slot 4 of the chassis, its topology path is 'CHASSIS, 1, BLADE, 4'. With this format, the components in the chassis can be determined along with their relative hierarchy to each other. This component inventory table is indexed by this unique topology path and the relevant numeric designations for the components are: CHASSIS, 0x01 Chassis MM, 0x02 Management Module BLADE, 0x03 Main system board of a blade | ||||
| CbootDeviceIndex | 1.3.6.1.4.1.2.3.51.2.22.1.15.1.2 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory An index for the boot device for the given topology id. | ||||
| CbootDeviceId | 1.3.6.1.4.1.2.3.51.2.22.1.15.1.3 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The device Id of the boot device. | ||||
| CbootDeviceActive | 1.3.6.1.4.1.2.3.51.2.22.1.15.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Specifies whether the boot device is active.
| ||||
| CbootDevicePresence | 1.3.6.1.4.1.2.3.51.2.22.1.15.1.5 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Specifies whether the boot device is present.
| ||||
| CbootDeviceLabel | 1.3.6.1.4.1.2.3.51.2.22.1.15.1.6 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The device label of the boot device. | ||||
| CbootDeviceUserLabel | 1.3.6.1.4.1.2.3.51.2.22.1.15.1.7 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The user label of the boot device. | ||||
| CbootDeviceOrder | 1.3.6.1.4.1.2.3.51.2.22.1.15.1.8 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory The sequence number in boot order of the boot device. 0 specifies this device is not in the boot sequence. | ||||
| TbootSequenceInfoTable | 1.3.6.1.4.1.2.3.51.2.22.1.16 | NA | mandatory | |
table · not-accessible · mandatory Table of blade boot sequence information. Contains the boot sequence information for each blade. | ||||
| RbootSequenceInfoEntry | 1.3.6.1.4.1.2.3.51.2.22.1.16.1 | NA | mandatory | |
| CbootSequenceInfoTopologyIndex | 1.3.6.1.4.1.2.3.51.2.22.1.16.1.1 | OCTET STRING (SIZE (0..100)) | RO | mandatory |
column · OCTET STRING (SIZE (0..100)) · read-only · mandatory The unique identifier for a row in this table. The chassis and each installed component is represented by a hardware topology tree, where each node in the tree represents a component. The path to a particular component consists of one or more <component>,<instance> pairs, where each successive pair is a child of the previous parent pair. As an example, the root of the tree is the chassis and is represented by the pair 'CHASSIS, 1'. This pair indicates the first instance of the chassis. If a blade is inserted in slot 4 of the chassis, its topology path is 'CHASSIS, 1, BLADE, 4'. With this format, the components in the chassis can be determined along with their relative hierarchy to each other. This component inventory table is indexed by this unique topology path and the relevant numeric designations for the components are: CHASSIS, 0x01 Chassis MM, 0x02 Management Module BLADE, 0x03 Main system board of a blade | ||||
| CbootSequenceInfoMaxBootDevices | 1.3.6.1.4.1.2.3.51.2.22.1.16.1.2 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory The maximum number of boot devices. | ||||
| CbootSequenceInfoBootSequence | 1.3.6.1.4.1.2.3.51.2.22.1.16.1.3 | OCTET STRING | RW | mandatory |
column · OCTET STRING · read-write · mandatory A blank delimited string of device ids in the order of the boot sequence. For example, 00000001 00000002 00000005. Note that the boot sequence list can change from a given order and can grow from a given order, but cannot be reduced in length. For example, if the sequence starts as 00000001 00000011, it could change to 00000001 00000014 or grow to 00000001 00000014 00000002. In the example above, if the 00000002 selection was no longer desired, the list should be changed to 00000001 00000014 00000014, essentially repeating the last device ID. Device ids must be listed in bootDeviceInfoTable. | ||||
| NswitchModule | 1.3.6.1.4.1.2.3.51.2.22.3 | |||
| NswitchModuleControl | 1.3.6.1.4.1.2.3.51.2.22.3.1 | |||
| TsmControlTable | 1.3.6.1.4.1.2.3.51.2.22.3.1.1 | NA | mandatory | |
table · not-accessible · mandatory Switch module control table. | ||||
| RsmControlEntry | 1.3.6.1.4.1.2.3.51.2.22.3.1.1.1 | NA | mandatory | |
| CsmControlIndex | 1.3.6.1.4.1.2.3.51.2.22.3.1.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Switch module control table index. | ||||
| CswitchModuleControlId | 1.3.6.1.4.1.2.3.51.2.22.3.1.1.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The switch module numeric identifier.
| ||||
| CsmPostResultsAvailable | 1.3.6.1.4.1.2.3.51.2.22.3.1.1.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Describes whether the switch module POST diagnostic result value contained in the smPostResultsValue is valid.
| ||||
| CsmPostResultsValue | 1.3.6.1.4.1.2.3.51.2.22.3.1.1.1.4 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The range of values and meanings are as follows: 0x00 - 0x7F ( 0 - 127) Base internal functions 0x80 - 0x9F (128 - 159) Internal interface failures 0xA0 - 0xAF (160 - 175) External interface failures 0xB0 - 0xFE (176 - 254) Reserved 0xFF (255) Switch completed POST successfully | ||||
| CswitchModuleMemDiagEnableDisable | 1.3.6.1.4.1.2.3.51.2.22.3.1.1.1.5 | INTEGER | RW | deprecated |
column · INTEGER · read-write · deprecated Switch module memory diagnostics enabled or disabled.
NOTE: The numeric values for the enumerations for enabled and disabled are non-traditional
(i.e. - 0 and 1 are swapped), however, they cannot be changed since this MIB is already
published.
| ||||
| CsmCfgCtrlEnableDisable | 1.3.6.1.4.1.2.3.51.2.22.3.1.1.1.6 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Switch module configuration control. When set to enabled, only the MM can manage
the module.
This MIB object can not be set, if MM grants switch module the Protected Mode permission.
This MIB object can not be set, if the switch module is participating in the Stacking Mode
and external management is protected.
NOTE: This MIB object is not applicable to modules that are running in Network Address
Translation (NAT) Mode. A value of disabled(0) will be returned.
| ||||
| CsmExtEthPortsEnableDisable | 1.3.6.1.4.1.2.3.51.2.22.3.1.1.1.7 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Switch module non-management ethernet ports enabled or disabled. This MIB object can not be set, if MM grants switch module the Protected Mode permission. This MIB object can not be set, if the switch module is participating in the Stacking Mode and External Port Access is protected.
| ||||
| CsmCfgCtrlOnResetEnableDisable | 1.3.6.1.4.1.2.3.51.2.22.3.1.1.1.9 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Switch module configuration control on resets (default and unsolicited).
When set to enabled, the factory default IP configuration will become
active when the I/O module is reset to factory defaults by either the
management module or the I/O module. If an I/O module reset is initiated
by a source other than the management module then the previous IP configuration
will be in affect. In both these cases the MM will lose IP communications with
the IOM.
This MIB object can not be set, if MM grants switch module the Protected Mode
permission and switch module goes into Protected Mode.
NOTE: The numeric values for the enumerations for enabled and disabled are non-traditional
(i.e. - 0 and 1 are swapped), however, they cannot be changed since this MIB is already
published.
NOTE: This MIB object is not applicable to modules that are running in Network Address
Translation (NAT) Mode. A value of disabled(1) will be returned.
| ||||
| CsmHealthState | 1.3.6.1.4.1.2.3.51.2.22.3.1.1.1.15 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The health state for the switch module. 0 = unknown, 1 = good, 2 = warning, 3 = bad.
| ||||
| CsmPMState | 1.3.6.1.4.1.2.3.51.2.22.3.1.1.1.16 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The Protected Mode Status for the switch module. standby- Protected Mode capability exists on the IOM but has not been activated on the switch module or the MM. pending - Protected Mode has been activated on the MM but not yet on the switch module. active - Protected Mode is active on both the switch module and the MM. attention - Protected Mode is enabled on the switch module but not on the MM.
| ||||
| CsmPMCtrlEnableDisable | 1.3.6.1.4.1.2.3.51.2.22.3.1.1.1.17 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory MM Protected Mode permission for the switch module. disabled - allow MM to disable Protected Mode Permission for the switch module. enabled - allow MM to grant Protected Mode Permission for the switch module.
| ||||
| CsmIOCompatibility | 1.3.6.1.4.1.2.3.51.2.22.3.1.1.1.18 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The compatibility status for the I/O module. The possible values and their meanings are as follows: Unknown: This indicates a communication error for the I/O module. OK: This is the normal (good) case where there are no compatibility issues between the I/O module and the modules it is internally wired to. No Fabric: This means the other end is not populated on any of the modules this I/O module is internally wired to (e.g. this is an Infiniband switch but none of the blades it is internally wired to has an expansion card attached in the corresponding expansion slot). Attention: Indicates one of the following cases: One or more of the modules this I/O module is internally wired to is in communication error The I/O module is powered off and at least one module it is internally wired to is powered on Mismatch: Indicates one of the following cases: Fabric types are incompatible An unknown I/O module type An unknown fabric type on a module the I/O module is internally wired to. | ||||
| TsmPingTable | 1.3.6.1.4.1.2.3.51.2.22.3.1.2 | NA | mandatory | |
table · not-accessible · mandatory Allows pinging one of the active assigned addresses of an I/O module. NOTE: This table is not applicable to modules that are running in Stacking Mode and IP configuration is protected. | ||||
| RsmPingEntry | 1.3.6.1.4.1.2.3.51.2.22.3.1.2.1 | NA | mandatory | |
row · not-accessible · mandatory Represents a single address that can be pinged | ||||
| CsmPingIndex | 1.3.6.1.4.1.2.3.51.2.22.3.1.2.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The switch module's slot number | ||||
| CsmPingAddressEntryIndex | 1.3.6.1.4.1.2.3.51.2.22.3.1.2.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The switch module's address entry index | ||||
| CsmPingAddress | 1.3.6.1.4.1.2.3.51.2.22.3.1.2.1.3 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The switch module's IPv4 or IPv6 address | ||||
| CsmPingAddressExecute | 1.3.6.1.4.1.2.3.51.2.22.3.1.2.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Pings the given IP address. NOTE: The GET operation for this object is meaningless.
| ||||
| TsmPowerRestartTable | 1.3.6.1.4.1.2.3.51.2.22.3.1.7 | NA | mandatory | |
table · not-accessible · mandatory Switch module power restart table. | ||||
| RsmPowerRestartEntry | 1.3.6.1.4.1.2.3.51.2.22.3.1.7.1 | NA | mandatory | |
| CsmPowerRestartIndex | 1.3.6.1.4.1.2.3.51.2.22.3.1.7.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Switch module power restart index. | ||||
| CsmPowerRestartId | 1.3.6.1.4.1.2.3.51.2.22.3.1.7.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The switch module numeric identifier.
| ||||
| CsmSwitchExists | 1.3.6.1.4.1.2.3.51.2.22.3.1.7.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether the switch module specified exists or not.
| ||||
| CsmMACAddress | 1.3.6.1.4.1.2.3.51.2.22.3.1.7.1.5 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Switch module MAC address. For IOMs which are members of a stack, this field is not applicable and should be disregarded. | ||||
| CsmIPAddress | 1.3.6.1.4.1.2.3.51.2.22.3.1.7.1.6 | IpAddress | RO | mandatory |
column · IpAddress · read-only · mandatory The switch module current IP address. If the switch module is participating in the Stacking Mode and IP Configuration is protected, then the stack management IP address is displayed. NOTE: IPv6 addresses for the switch can be view with the smIPv6AddressTable. | ||||
| CswitchModulePowerOnOff | 1.3.6.1.4.1.2.3.51.2.22.3.1.7.1.7 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory I/O Module power on or power off. If powering on a currently powered off I/O Module, then the I/O Module will execute a POST. The results of this POST will need to be retrieved using the 'Post Results' command. NOTE: When powering off a currently powered on I/O Module, a minimum of 1 second is needed to allow the module to power off before powering back on. The value 'shutdownInProgress' is for I/O Modules that may take some time to transition from 'poweron' to 'poweroff'. This MIB object can not be set, if MM grants the I/O Module the Protected Mode permission and module goes into Protected Mode.
| ||||
| CsmReset | 1.3.6.1.4.1.2.3.51.2.22.3.1.7.1.8 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory For the case where the switch module is currently powered on, this command will effectively power off and then power on the switch module indicated and cause it to run its POST test. For the case where the switch module is currently powered off, the command will just power on the switch module. This MIB object can not be set, if MM grants switch module the Protected Mode permission and switch module goes into Protected Mode. NOTE: Value returned for the GET command is meaningless for this MIB object.
| ||||
| CsmResetToDefault | 1.3.6.1.4.1.2.3.51.2.22.3.1.7.1.9 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory For the case where the switch module is currently powered on, this command will effectively power off and then power on the switch module indicated and cause it to run its POST test. For the case where the switch module is currently powered off, the command will just power on the switch module. In both cases, the switch module will reset the configuration to the default values. This MIB object can not be set, if MM grants switch module the Protected Mode permission and switch module goes into Protected Mode. This MIB object can not be set, if the switch module is participating in the Stacking Mode and reset to default is protected. NOTE: Value returned for the GET command is meaningless for this MIB object.
| ||||
| CsmRestartAndRunStdDiag | 1.3.6.1.4.1.2.3.51.2.22.3.1.7.1.10 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory To power cycle the selected module(s) and then run the standard diagnostic test package. NOTE: Value returned for the GET command is meaningless for this MIB object.
| ||||
| CsmRestartAndRunExtDiag | 1.3.6.1.4.1.2.3.51.2.22.3.1.7.1.11 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory To power cycle the selected module(s) and then run the extended diagnostic test package. This option is not supported on all I/O modules. NOTE: Value returned for the GET command is meaningless for this MIB object.
| ||||
| CsmRestartAndRunFullDiag | 1.3.6.1.4.1.2.3.51.2.22.3.1.7.1.12 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory To power cycle the selected module(s) and then run the full diagnostic test package. The full diagnostic test package may take over 5 minutes to run. This option is not supported on all I/O modules. NOTE: Value returned for the GET command is meaningless for this MIB object.
| ||||
| CsmPowerOnRestartDelay | 1.3.6.1.4.1.2.3.51.2.22.3.1.7.1.15 | INTEGER (0..32767) | RW | mandatory |
column · INTEGER (0..32767) · read-write · mandatory Restart delay (in seconds) when power is applied to a switch module. | ||||
| CsmSwitchWidth | 1.3.6.1.4.1.2.3.51.2.22.3.1.7.1.21 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Switch module width. | ||||
| CsmManufacturingID | 1.3.6.1.4.1.2.3.51.2.22.3.1.7.1.22 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Switch module hardware VPD manufacturing ID. | ||||
| CsmStackingModeState | 1.3.6.1.4.1.2.3.51.2.22.3.1.7.1.23 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The Stacking Mode Status for the switch module. standby - I/O module has stacking capability but is not part of a stack. member - I/O module has stacking capability and is part of a stack in the member role. master - I/O module has stacking capability and is part of a stack in the master role. NOTE: The term disabled was changed to the term standby to be more descriptive.
| ||||
| CsmStackingModeInfo | 1.3.6.1.4.1.2.3.51.2.22.3.1.7.1.24 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory A string containing a text description about the details of which functions are protected for a switch module when it is in Stacking Mode as Master or Member. The possible functions protected by switch modules are IP configuration, External Port Access, External Management all over ports and Restore to defaults. | ||||
| TsmIOCompatibilityTable | 1.3.6.1.4.1.2.3.51.2.22.3.1.10 | NA | mandatory | |
table · not-accessible · mandatory Switch module control table. | ||||
| RsmIOCompatibilityEntry | 1.3.6.1.4.1.2.3.51.2.22.3.1.10.1 | NA | mandatory | |
row · not-accessible · mandatory Switch module IO compatibility table entry | ||||
| CsmIOCompatibilityIndex | 1.3.6.1.4.1.2.3.51.2.22.3.1.10.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Switch module IO compatibility index. | ||||
| CsmIOCompatibilityId | 1.3.6.1.4.1.2.3.51.2.22.3.1.10.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The switch module numeric identifier.
| ||||
| CsmIOCompatibilityModuleBay | 1.3.6.1.4.1.2.3.51.2.22.3.1.10.1.3 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The modules (identified by an id string) that this I/O module can communicate with over the midplane networking fabric (i.e. a physical path exists between the I/O module and this module). | ||||
| CsmIOCompatibilityModulePower | 1.3.6.1.4.1.2.3.51.2.22.3.1.10.1.4 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The power state of the module specified in smIOCompatibilityModuleBay. | ||||
| CsmIOCompatibilityModuleFabricType | 1.3.6.1.4.1.2.3.51.2.22.3.1.10.1.5 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The I/O fabric type on the module side for the module. 'n/a' will be displayed if the corresponding channel is not populated on the module side (e.g. we are looking at the details for an Infiniband switch but the blade does not have an Infiniband expansion card attached in the corresponding expansion slot). | ||||
| CsmIOCompatibilityStatus | 1.3.6.1.4.1.2.3.51.2.22.3.1.10.1.6 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The compatibility status for this I/O module and the module specified
in smIOCompatibilityModuleBay.
The possible values are:
OK: No compatibility issues
n/a: Indicates the corresponding channel is not populated on the module
side even though the module is present (e.g. we are looking at the details
for an Infiniband switch but the blade specified in smIOCompatibilityModuleBay
does not have an Infiniband expansion card attached in the corresponding expansion slot).
Attention: Indicates one of the following:
The module specified in smIOCompatibilityModuleBay has a communication error.
The I/O module is powered off but the module specified in smIOCompatibilityModuleBay is powered on.
Mismatch: Indicates one of the following cases::
Fabric types are incompatible
Unknown fabric type on the module side
Unknown I/O module type | ||||
| CsmIOCompatibilityTargetTopologyPath | 1.3.6.1.4.1.2.3.51.2.22.3.1.10.1.7 | OCTET STRING (SIZE (0..100)) | RO | mandatory |
column · OCTET STRING (SIZE (0..100)) · read-only · mandatory The unique identifier for a component which communicates with this IO module. This is the same component identified with an id string in the smIOCompatibilityModuleBay column. The installed component is represented by a hardware topology tree, where each node in the tree represents a component. The path to a particular component consists of one or more <component>,<instance> pairs, where each successive pair is a child of the previous parent pair. As an example, the root of the tree is the chassis and is represented by the pair 'CHASSIS, 1'. This pair indicates the first instance of the chassis. If a blade is inserted in slot 4 of the chassis, its topology path is 'CHASSIS, 1, BLADE, 4'. With this format, the components in the chassis can be determined along with their relative hierarchy to each other. This component table is indexed by this unique topology path and the numeric designations for the components are: CHASSIS, 0x01 Chassis MM, 0x02 Management Module BLADE, 0x03 Main system board of a blade POWER, 0x04 Power Supply, Power Module, etc COOLING, 0x05 Fan, blower, or other cooling device IO_MODULE, 0x06 Has I/O interface, i.e. - switch or bridge MEDIA, 0x07 Media device PROCESSOR, 0x08 Any processor, processor module, etc STORAGE, 0x09 Any type of storage device EXPANSION, 0x0A Expansion Card (not covered by more specific type) MEMORY, 0x0B Any memory device, module, etc MFRU, 0x0C Managed FRU Device PANEL, 0x0D Any sort of panel device, such as a front panel BLADE_EXPANSION_MODULE, 0x0E Expansion option (BEM) such as PEU, BSE, etc CARD_EXPANSION, 0x0F Expansion card, ie. daughter card CARD_HS_EXPANSION, 0x10 High Speed Expansion card, ie. daughter card INTERPOSER, 0x11 Interposer device CLOCK, 0x12 Clock card MUX, 0x13 Mulitplexer card ADDIN, 0x14 cKVM card & other addin cards STORAGE_MODULE, 0x15 Container of one or more Storage Devices SYS_EXPANSION_CARD, 0x16 Management card BATTERY, 0x17 A single battery BATTERY_MODULE, 0x18 Container of one or more batteries REAR_LED, 0x19 Rear LED card MEMORY_BANK, 0x1A Memory banks AIR_FILTER, 0x1B Filter mechanism (bezel) SERIAL_PORT_MODULE, 0x1C Container of one or more serial ports PARENT, 0x1D Reference to parent for multi-parent support PHY_PORT, 0x1E Physical port IO_EXPANDER, 0x1F RAID card CABLE, 0x20 Cable/Interconnect FAN_MUX 0x29 Fan multiplexer card PCI_EXPRESS, 0x32 PCI express card on (PEN) FLASH_DIMM, 0x33 Used for SPD devices that matches the silkscreen of the DIMM slot RACK, 0x50 Rack PLATFORM, 0x51 Generic Platform like rack mounted server/appliance DATAPLEX, 0x52 DataPlex OTHER, 0x53 Other unknown etc. PERIPHERAL_MODULE, 0x54 SYSTEM_BOARD, 0x55 System board PROCESSOR_MODULE, 0x56 BACK_PANEL, 0x57 POWER_SYSTEM_BOARD, 0x58 STORAGE_BACKPLANE, 0x59 Drive back plane PROC_BOARD, 0x5A Holds 1 or more processors POWER_DI, 0x5B Power mgt / power distribution board CHASSIS_BACK_PANEL, 0x5C SUB_CHASSIS, 0x5D OTHER_CHASSIS_BOARD, 0x5E DEVICE_MODULE, 0x5F REMOTE_DEVICE, 0x60 Remote mgt communication device EXTERNAL_ENVIRONMENT, 0x61 Such as external temp sensor for outside box temps PROC_MEMORY_MODULE, 0x62 Processors and memory on same module | ||||
| NswitchModuleConfig | 1.3.6.1.4.1.2.3.51.2.22.3.2 | |||
| NswitchMgmtNetworkCfg | 1.3.6.1.4.1.2.3.51.2.22.3.2.1 | |||
| NswitchCurrentNwCfg | 1.3.6.1.4.1.2.3.51.2.22.3.2.1.1 | |||
| TsmCurrentIPInfoTable | 1.3.6.1.4.1.2.3.51.2.22.3.2.1.1.1 | NA | mandatory | |
table · not-accessible · mandatory Switch module current IP information. NOTE: This MIB object is not applicable to modules that are running in Stacking Mode and IP configuration is protected. | ||||
| RsmCurrentIPInfoEntry | 1.3.6.1.4.1.2.3.51.2.22.3.2.1.1.1.1 | NA | mandatory | |
row · not-accessible · mandatory Switch module current IP table entry. NOTE: This MIB object is not applicable to modules that are running in Stacking Mode and IP configuration is protected.
| ||||
| CsmCurrentIPInfoIndex | 1.3.6.1.4.1.2.3.51.2.22.3.2.1.1.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Switch module current IP info index. NOTE: This MIB object is not applicable to modules that are running in Stacking Mode and IP configuration is protected. | ||||
| CsmCurrentIPInfoId | 1.3.6.1.4.1.2.3.51.2.22.3.2.1.1.1.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The switch module numeric identifier. NOTE: This MIB object is not applicable to modules that are running in Stacking Mode and IP configuration is protected.
| ||||
| CsmCurrentIPInfoExists | 1.3.6.1.4.1.2.3.51.2.22.3.2.1.1.1.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether the switch module specified exists or not. NOTE: This MIB object is not applicable to modules that are running in Stacking Mode and IP configuration is protected.
| ||||
| CsmCurrentIPInfoPowerState | 1.3.6.1.4.1.2.3.51.2.22.3.2.1.1.1.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether the I/O Module specified is powered on or not. The value 'shutdownInProgress' is for the I/O Module that may take some time to transition from 'poweron' to 'poweroff'. NOTE: This MIB object is not applicable to modules that are running in Stacking Mode and IP configuration is protected.
| ||||
| CsmCurrentIPAddr | 1.3.6.1.4.1.2.3.51.2.22.3.2.1.1.1.1.6 | IpAddress | RO | mandatory |
column · IpAddress · read-only · mandatory The switch module current IP address. NOTE: This MIB object is not applicable to modules that are running in Stacking Mode and IP configuration is protected. | ||||
| CsmCurrentSubnetMask | 1.3.6.1.4.1.2.3.51.2.22.3.2.1.1.1.1.7 | IpAddress | RO | mandatory |
column · IpAddress · read-only · mandatory The switch module current subnet mask. NOTE: This MIB object is not applicable to modules that are running in Stacking Mode and IP configuration is protected. | ||||
| CsmCurrentGateway | 1.3.6.1.4.1.2.3.51.2.22.3.2.1.1.1.1.8 | IpAddress | RO | mandatory |
column · IpAddress · read-only · mandatory The switch module current IP gateway. NOTE: This MIB object is not applicable to modules that are running in Stacking Mode and IP configuration is protected. | ||||
| CsmCurrentIPConfigMethod | 1.3.6.1.4.1.2.3.51.2.22.3.2.1.1.1.1.9 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The switch module current IP configuration method. NOTE: This MIB object is not applicable to modules that are running in Stacking Mode and IP configuration is protected.
| ||||
| NswitchNewNwCfg | 1.3.6.1.4.1.2.3.51.2.22.3.2.1.2 | |||
| TsmNewIPInfoTable | 1.3.6.1.4.1.2.3.51.2.22.3.2.1.2.1 | NA | mandatory | |
table · not-accessible · mandatory Switch module new IP information. NOTE: This MIB object is not applicable to modules that are running in Network Address Translation (NAT) Mode or Stacking Mode and IP configuration is protected. | ||||
| RsmNewIPInfoEntry | 1.3.6.1.4.1.2.3.51.2.22.3.2.1.2.1.1 | NA | mandatory | |
row · not-accessible · mandatory Switch module new IP configuration information table entry. NOTE: This MIB table is not applicable to modules that are running in Network Address Translation (NAT) Mode or Stacking Mode and IP configuration is protected.
| ||||
| CsmNewIPInfoIndex | 1.3.6.1.4.1.2.3.51.2.22.3.2.1.2.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Switch module new IP info index. NOTE: This MIB object is not applicable to modules that are running in Network Address Translation (NAT) Mode or Stacking Mode and IP configuration is protected. | ||||
| CsmNewIPInfoId | 1.3.6.1.4.1.2.3.51.2.22.3.2.1.2.1.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The switch module numeric identifier. NOTE: This MIB object is not applicable to modules that are running in Network Address Translation (NAT) Mode or Stacking Mode and IP configuration is protected.
| ||||
| CsmNewIPInfoExists | 1.3.6.1.4.1.2.3.51.2.22.3.2.1.2.1.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether the switch module specified exists or not. NOTE: This MIB object is not applicable to modules that are running in Network Address Translation (NAT) Mode or Stacking Mode and IP configuration is protected.
| ||||
| CsmNewIPInfoPowerState | 1.3.6.1.4.1.2.3.51.2.22.3.2.1.2.1.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether the switch module specified is powered on or not. NOTE: This MIB object is not applicable to modules that are running in Network Address Translation (NAT) Mode or Stacking Mode and IP configuration is protected..
| ||||
| CsmNewIPAddr | 1.3.6.1.4.1.2.3.51.2.22.3.2.1.2.1.1.6 | IpAddress | RW | mandatory |
column · IpAddress · read-write · mandatory The switch module new IP address. Before setting this object to a new value, smNewIpconfigEnableDisable object must first be set to disabled. NOTE: This MIB object can not be set if the MM grants the switch module Protected Mode permission and the switch module goes into Protected Mode. NOTE: This MIB object can not be set if the switch module is in Stacking Mode and IP Configuration is protected. NOTE: This MIB object is not applicable to modules that are running in Network Address Translation (NAT) Mode. | ||||
| CsmNewSubnetMask | 1.3.6.1.4.1.2.3.51.2.22.3.2.1.2.1.1.7 | IpAddress | RW | mandatory |
column · IpAddress · read-write · mandatory The switch module new subnet mask. Before setting this object to a new value, smNewIpconfigEnableDisable object must first be set to disabled. NOTE: This MIB object can not be set if the MM grants the switch module Protected Mode permission and the switch module goes into Protected Mode. NOTE: This MIB object can not be set if the switch module is in Stacking Mode, and IP Configuration is protected. NOTE: This MIB object is not applicable to modules that are running in Network Address Translation (NAT) Mode. | ||||
| CsmNewGateway | 1.3.6.1.4.1.2.3.51.2.22.3.2.1.2.1.1.8 | IpAddress | RW | mandatory |
column · IpAddress · read-write · mandatory The switch module new IP gateway. Before setting this object to a new value, smNewIpconfigEnableDisable object must first be set to disabled. NOTE: This MIB object can not be set if the MM grants the switch module Protected Mode permission and the switch module goes into Protected Mode. NOTE: This MIB object can not be set if the switch module is in Stacking Mode, and IP Configuration is protected. NOTE: This MIB object is not applicable to modules that are running in Network Address Translation (NAT) Mode. | ||||
| CsmNewIPConfigMethod | 1.3.6.1.4.1.2.3.51.2.22.3.2.1.2.1.1.9 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory The switch module new IP configuration method. Before setting this object to a new value, smNewIpconfigEnableDisable object must first be set to disabled. NOTE: This MIB object can not be set if the MM grants the switch module Protected Mode permission and the switch module goes into Protected Mode. NOTE: This MIB object can not be set if the switch module is in Stacking Mode, and IP Configuration is protected. NOTE: This MIB object is not applicable to modules that are running in Network Address Translation (NAT) Mode.
| ||||
| CsmNewIPConfigEnableDisable | 1.3.6.1.4.1.2.3.51.2.22.3.2.1.2.1.1.10 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory A set command enables a new IP configuration that has been previously defined. A get command indicates whether the new IP configuration information has been enabled. NOTE: This MIB object can not be set if the MM grants the switch module Protected Mode permission and the switch module goes into Protected Mode. NOTE: This MIB object can not be set if the switch module is in Stacking Mode, and IP Configuration is protected. NOTE: This MIB object is not applicable to modules that are running in Network Address Translation (NAT) Mode.
| ||||
| NswitchIPv6Config | 1.3.6.1.4.1.2.3.51.2.22.3.2.1.4 | |||
| TsmIPv6ConfigTable | 1.3.6.1.4.1.2.3.51.2.22.3.2.1.4.1 | NA | mandatory | |
table · not-accessible · mandatory A table of IPv6 configuration options for switch modules. NOTE: This MIB object is not applicable to modules that are running in Stacking Mode and IP configuration is protected. NOTE: This MIB object is not applicable to modules that do not support IPv6. | ||||
| RsmIPv6ConfigEntry | 1.3.6.1.4.1.2.3.51.2.22.3.2.1.4.1.1 | NA | mandatory | |
row · not-accessible · mandatory IPv6 configuration options for a switch module.. NOTE: This MIB object is not applicable to modules that are running in Stacking Mode and IP configuration is protected. NOTE: This MIB object is not applicable to modules that do not support IPv6.
| ||||
| CsmIPv6ConfigIndex | 1.3.6.1.4.1.2.3.51.2.22.3.2.1.4.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The switch module's slot number | ||||
| CsmIPv6ConfigEnabled | 1.3.6.1.4.1.2.3.51.2.22.3.2.1.4.1.1.2 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Enables/Disables IPv6 support on the switch module.
| ||||
| CsmIPv6ConfigStatic | 1.3.6.1.4.1.2.3.51.2.22.3.2.1.4.1.1.3 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Enables/Disables IPv6 static configuration support on the switch module.
| ||||
| CsmDHCPv6ConfigEnabled | 1.3.6.1.4.1.2.3.51.2.22.3.2.1.4.1.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Enables/Disables DHCPv6 address configuration support on the switch module.
| ||||
| CsmIPv6ConfigStatelessEnabled | 1.3.6.1.4.1.2.3.51.2.22.3.2.1.4.1.1.5 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Enables/Disables IPv6 stateless auto-configuration support on the switch module.
| ||||
| TsmIPv6AddressTable | 1.3.6.1.4.1.2.3.51.2.22.3.2.1.4.2 | NA | mandatory | |
table · not-accessible · mandatory A table of assigned IPv6 addresses for switch modules. NOTE: This MIB object is not applicable to modules that are running in Stacking Mode and IP configuration is protected. NOTE: This MIB object is not applicable to modules that do not support IPv6. | ||||
| RsmIPv6AddressEntry | 1.3.6.1.4.1.2.3.51.2.22.3.2.1.4.2.1 | NA | mandatory | |
row · not-accessible · mandatory The assigned IPv6 address for a given switch module NOTE: This MIB object is not applicable to modules that are running in Stacking Mode and IP configuration is protected. NOTE: This MIB object is not applicable to modules that do not support IPv6. | ||||
| CsmIPv6AddressIndex | 1.3.6.1.4.1.2.3.51.2.22.3.2.1.4.2.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The switch module's slot number | ||||
| CsmIPv6AddressEntryIndex | 1.3.6.1.4.1.2.3.51.2.22.3.2.1.4.2.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The switch module's address entry index | ||||
| CsmIPv6AddressType | 1.3.6.1.4.1.2.3.51.2.22.3.2.1.4.2.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The address type.
| ||||
| CsmIPv6Address | 1.3.6.1.4.1.2.3.51.2.22.3.2.1.4.2.1.4 | InetAddressIPv6 | RO | mandatory |
column · InetAddressIPv6 · read-only · mandatory The assigned IPv6 address | ||||
| CsmIPv6AddressPrefixLen | 1.3.6.1.4.1.2.3.51.2.22.3.2.1.4.2.1.5 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The prefix length for the given address. | ||||
| CsmIPv6AddressDefaultRoute | 1.3.6.1.4.1.2.3.51.2.22.3.2.1.4.2.1.6 | InetAddressIPv6 | RO | mandatory |
column · InetAddressIPv6 · read-only · mandatory The default route used for the given address | ||||
| TsmIPv6StaticConfigTable | 1.3.6.1.4.1.2.3.51.2.22.3.2.1.4.3 | NA | mandatory | |
table · not-accessible · mandatory Allows configuration of static IPv6 information for supported IO modules. NOTE: This MIB object is not applicable to modules that are running in Stacking Mode and IP configuration is protected. NOTE: This MIB object is not applicable to modules that do not support IPv6. | ||||
| RsmIPv6StaticConfigEntry | 1.3.6.1.4.1.2.3.51.2.22.3.2.1.4.3.1 | NA | mandatory | |
row · not-accessible · mandatory The static IP address assignment information for an IO module. Once the assignement has taken place the address will show up as a row in the smIPv6AddressTable NOTE: This MIB object is not applicable to modules that are running in Stacking Mode and IP configuration is protected. NOTE: This MIB object is not applicable to modules that do not support IPv6.
| ||||
| CsmIPv6StaticIndex | 1.3.6.1.4.1.2.3.51.2.22.3.2.1.4.3.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The switch module's slot number | ||||
| CsmIPv6StaticAddress | 1.3.6.1.4.1.2.3.51.2.22.3.2.1.4.3.1.2 | InetAddressIPv6 | RW | mandatory |
column · InetAddressIPv6 · read-write · mandatory The assigned IPv6 address. NOTE: If changing with smIPv6StaticAddressPrefixLen and/or smIPv6StaticAddressDefaultRoute sending the update as a single SET command(in one PDU) will minimize the potential downtime of the target switch. NOTE: Sets on this object can take a few seconds. You may need to update your SNMP timeout when modifying this setting. | ||||
| CsmIPv6StaticAddressPrefixLen | 1.3.6.1.4.1.2.3.51.2.22.3.2.1.4.3.1.3 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory The prefix length for the given address. NOTE: If changing with smIPv6StaticAddress and/or smIPv6StaticAddressDefaultRoute sending the update as a single SET command(in one PDU) will minimize the potential downtime of the target switch. NOTE: Sets on this object can take a few seconds. You may need to update your SNMP timeout when modifying this setting. | ||||
| CsmIPv6StaticAddressDefaultRoute | 1.3.6.1.4.1.2.3.51.2.22.3.2.1.4.3.1.4 | InetAddressIPv6 | RW | mandatory |
column · InetAddressIPv6 · read-write · mandatory The default route used for the given address NOTE: If changing with smIPv6StaticAddressPrefixLen and/or smIPv6StaticAddress sending the update as a single SET command(in one PDU) will minimize the potential downtime of the target switch. NOTE: Sets on this object can take a few seconds. You may need to update your SNMP timeout when modifying this setting. | ||||
| NswitchPortCfg | 1.3.6.1.4.1.2.3.51.2.22.3.2.2 | |||
| NswitchModOnePortCfg | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.1 | |||
| TsmOnePortCfgTable | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.1.1 | NA | mandatory | |
table · not-accessible · mandatory Switch Module 1 port configuration information. NOTE: This option is not supported on all I/O modules. | ||||
| RsmOnePortCfgEntry | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.1.1.1 | NA | mandatory | |
row · not-accessible · mandatory Switch Module 1 port configuration information table entry
| ||||
| CsmOnePortCfgIndex | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.1.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Switch Module 1 port sequence index. | ||||
| CsmOnePortCfgLabel | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.1.1.1.2 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Switch Module 1 port label | ||||
| CsmOnePortCfgType | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.1.1.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Switch Module 1 port type:
External port: This port is connected to external device and is for data traffic.
External management port: This port is solely for external management connection.
This port is not used for data traffic from remote to blades.
External dual port: This external port is used for both data traffic to blades as well as for management.
Blade port: This port is connected to the blade.
Management Module Management port: This port is connected to the Management Module.
Uplink port: This port is configured for up link functionality.
Inter-Module port: This port is either by design connected to another I/O Module,
by user configured, or by MM setting the port type.
Inter-Module Management port: This port is connected to another I/O Module for management purpose.
The port type is either by design connected to another I/O Module, by user configured,
or by MM setting the port type.
Inter-Module Dual port: The port is connected to another I/O Module and can be used for both data
and management purposes. The port type is either by design connected to another I/O Module,
by user configured, or by MM setting the port type.
| ||||
| CsmOnePortCfgLinkSetting | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.1.1.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Current port link setting for Switch Module 1.
| ||||
| CsmOnePortCfgLinkState | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.1.1.1.5 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Current port link state of Switch Module 1.
| ||||
| CsmOnePortCfgSpeedSetting | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.1.1.1.6 | OCTET STRING | RW | mandatory |
column · OCTET STRING · read-write · mandatory Set the port speed using the data rate and duplex value. For examples: 100mh: 100 Mbps in Half Duplex; 10gf: 10 Gbps in Full Duplex; auto: The working speed of the physical port can be tuned automatically. NOTE: Only the speeds from smOnePortCfgAvailSpeeds object are applicable to setting this mib object. | ||||
| CsmOnePortCfgSpeedStatus | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.1.1.1.7 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Current port speed of Switch Module 1. | ||||
| CsmOnePortCfgAvailSpeeds | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.1.1.1.8 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Available speed setting per port for Switch Module 1. If there is more than one setting, the speeds are separated by a comma and then a space. | ||||
| CsmOnePortCfgMedia | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.1.1.1.9 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Port media type of Switch Module 1.
| ||||
| CsmOnePortCfgProtocol | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.1.1.1.10 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Port protocol of Switch Module 1.
| ||||
| CsmOnePortCfgWidth | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.1.1.1.11 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The width of the port in terms of how many combined cables are present for Switch Module 1. A value of 0 indicates this field is not applicable to the switch ports. This data is also known as the lane count. | ||||
| CsmOnePortCfgCableLength | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.1.1.1.12 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The length (in meters) of the cable supported by this port for Switch Module 1. A value of 0 indicates this field is not applicable to the switch ports. | ||||
| CsmOnePortCfgCableType | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.1.1.1.13 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory External cable type for this port, for example, active copper or passive fiber. | ||||
| CsmOnePortCfgVendorName | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.1.1.1.14 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The cable manufacturer. | ||||
| CsmOnePortCfgCompatibility | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.1.1.1.15 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Compatibility of the external cable that is plugged into the port.
| ||||
| CsmOnePortCfgDataRate | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.1.1.1.16 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Data rate supported for this port.
| ||||
| NswitchModTwoPortCfg | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.2 | |||
| TsmTwoPortCfgTable | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.2.1 | NA | mandatory | |
table · not-accessible · mandatory Switch Module 2 port configuration information. Note: This option is not supported on all I/O modules. | ||||
| RsmTwoPortCfgEntry | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.2.1.1 | NA | mandatory | |
row · not-accessible · mandatory Switch Module 2 port configuration information table entry
| ||||
| CsmTwoPortCfgIndex | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.2.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Switch Module 2 port sequence index. | ||||
| CsmTwoPortCfgLabel | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.2.1.1.2 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Switch Module 2 port label | ||||
| CsmTwoPortCfgType | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.2.1.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Switch Module 2 port type:
External port: This port is connected to external device and is for data traffic.
External management port: This port is solely for external management connection.
This port is not used for data traffic from remote to blades.
External dual port: This external port is used for both data traffic to blades as well as for management.
Blade port: This port is connected to the blade.
Management Module Management port: This port is connected to the Management Module.
Uplink port: This port is configured for up link functionality.
Inter-Module port: This port is either by design connected to another I/O Module,
by user configured, or by MM setting the port type.
Inter-Module Management port: This port is connected to another I/O Module for management purpose.
The port type is either by design connected to another I/O Module, by user configured,
or by MM setting the port type.
Inter-Module Dual port: The port is connected to another I/O Module and can be used for both data
and management purposes. The port type is either by design connected to another I/O Module,
by user configured, or by MM setting the port type.
| ||||
| CsmTwoPortCfgLinkSetting | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.2.1.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Current port link setting for Switch Module 2.
| ||||
| CsmTwoPortCfgLinkState | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.2.1.1.5 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Current port link state of Switch Module 2.
| ||||
| CsmTwoPortCfgSpeedSetting | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.2.1.1.6 | OCTET STRING | RW | mandatory |
column · OCTET STRING · read-write · mandatory Set the port speed using the data rate and duplex value. For examples: 100mf: 100Mbps in Half Duplex; 10gf: 10 Gbps in Full Duplex; auto: The working speed of the physical port can be tuned automatically. NOTE: Only the speeds from smTwoPortCfgAvailSpeeds are applicable to setting this mib object. | ||||
| CsmTwoPortCfgSpeedStatus | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.2.1.1.7 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Current port speed of Switch Module 2. | ||||
| CsmTwoPortCfgAvailSpeeds | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.2.1.1.8 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Available speed setting per port for Switch Module 2. If there is more than one setting, the speeds are separated by a comma and then a space. | ||||
| CsmTwoPortCfgMedia | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.2.1.1.9 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Port media type of Switch Module 2.
| ||||
| CsmTwoPortCfgProtocol | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.2.1.1.10 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Port protocol of Switch Module 2.
| ||||
| CsmTwoPortCfgWidth | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.2.1.1.11 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The width of the port in terms of how many combined cables are present for Switch Module 2. A value of 0 indicates this field is not applicable to the switch ports. This data is also known as the lane count. | ||||
| CsmTwoPortCfgCableLength | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.2.1.1.12 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The length (in meters) of the cable supported by this port for Switch Module 2. A value of 0 indicates this field is not applicable to the switch ports. | ||||
| CsmTwoPortCfgCableType | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.2.1.1.13 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory External cable type for this port, for example, active copper or passive fiber. | ||||
| CsmTwoPortCfgVendorName | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.2.1.1.14 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The cable manufacturer. | ||||
| CsmTwoPortCfgCompatibility | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.2.1.1.15 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Compatibility of the external cable that is plugged into the port.
| ||||
| CsmTwoPortCfgDataRate | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.2.1.1.16 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Data rate supported for this port.
| ||||
| NswitchModThreePortCfg | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.3 | |||
| TsmThreePortCfgTable | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.3.1 | NA | mandatory | |
table · not-accessible · mandatory Switch Module 3 port configuration information. Note: This option is not supported on all I/O modules. | ||||
| RsmThreePortCfgEntry | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.3.1.1 | NA | mandatory | |
row · not-accessible · mandatory Switch Module 3 port configuration information table entry
| ||||
| CsmThreePortCfgIndex | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.3.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Switch Module 3 port sequence index. | ||||
| CsmThreePortCfgLabel | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.3.1.1.2 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Switch Module 3 port label | ||||
| CsmThreePortCfgType | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.3.1.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Switch Module 3 port type:
External port: This port is connected to external device and is for data traffic.
External management port: This port is solely for external management connection.
This port is not used for data traffic from remote to blades.
External dual port: This external port is used for both data traffic to blades as well as for management.
Blade port: This port is connected to the blade.
Management Module Management port: This port is connected to the Management Module.
Uplink port: This port is configured for up link functionality.
Inter-Module port: This port is either by design connected to another I/O Module,
by user configured, or by MM setting the port type.
Inter-Module Management port: This port is connected to another I/O Module for management purpose.
The port type is either by design connected to another I/O Module, by user configured,
or by MM setting the port type.
Inter-Module Dual port: The port is connected to another I/O Module and can be used for both data
and management purposes. The port type is either by design connected to another I/O Module,
by user configured, or by MM setting the port type.
| ||||
| CsmThreePortCfgLinkSetting | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.3.1.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Current port link setting for Switch Module 3.
| ||||
| CsmThreePortCfgLinkState | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.3.1.1.5 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Current port link state of Switch Module 3.
| ||||
| CsmThreePortCfgSpeedSetting | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.3.1.1.6 | OCTET STRING | RW | mandatory |
column · OCTET STRING · read-write · mandatory Set the port speed using the data rate and duplex value. For examples: 100mf: 100Mbps in Half Duplex; 10gf: 10 Gbps in Full Duplex; auto: The working speed of the physical port can be tuned automatically. NOTE: Only the speeds from smThreePortCfgAvailSpeeds are applicable to setting this mib object. | ||||
| CsmThreePortCfgSpeedStatus | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.3.1.1.7 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Current port speed of Switch Module 3. | ||||
| CsmThreePortCfgAvailSpeeds | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.3.1.1.8 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Available speed setting per port for Switch Module 3. If there is more than one setting, the speeds are separated by a comma and then a space. | ||||
| CsmThreePortCfgMedia | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.3.1.1.9 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Port media type of Switch Module 3.
| ||||
| CsmThreePortCfgProtocol | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.3.1.1.10 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Port protocol of Switch Module 3.
| ||||
| CsmThreePortCfgWidth | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.3.1.1.11 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The width of the port in terms of how many combined cables are present for Switch Module 3. A value of 0 indicates this field is not applicable to the switch ports. This data is also known as the lane count. | ||||
| CsmThreePortCfgCableLength | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.3.1.1.12 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The length (in meters) of the cable supported by this port for Switch Module 3. A value of 0 indicates this field is not applicable to the switch ports. | ||||
| CsmThreePortCfgCableType | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.3.1.1.13 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory External cable type for this port, for example, active copper or passive fiber. | ||||
| CsmThreePortCfgVendorName | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.3.1.1.14 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The cable manufacturer. | ||||
| CsmThreePortCfgCompatibility | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.3.1.1.15 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Compatibility of the external cable that is plugged into the port.
| ||||
| CsmThreePortCfgDataRate | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.3.1.1.16 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Data rate supported for this port.
| ||||
| NswitchModFourPortCfg | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.4 | |||
| TsmFourPortCfgTable | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.4.1 | NA | mandatory | |
table · not-accessible · mandatory Switch Module 4 port configuration information. Note: This option is not supported on all I/O modules. | ||||
| RsmFourPortCfgEntry | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.4.1.1 | NA | mandatory | |
row · not-accessible · mandatory Switch Module 4 port configuration information table entry
| ||||
| CsmFourPortCfgIndex | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.4.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Switch Module 4 port sequence index. | ||||
| CsmFourPortCfgLabel | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.4.1.1.2 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Switch Module 4 port label | ||||
| CsmFourPortCfgType | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.4.1.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Switch Module 4 port type:
External port: This port is connected to external device and is for data traffic.
External management port: This port is solely for external management connection.
This port is not used for data traffic from remote to blades.
External dual port: This external port is used for both data traffic to blades as well as for management.
Blade port: This port is connected to the blade.
Management Module Management port: This port is connected to the Management Module.
Uplink port: This port is configured for up link functionality.
Inter-Module port: This port is either by design connected to another I/O Module,
by user configured, or by MM setting the port type.
Inter-Module Management port: This port is connected to another I/O Module for management purpose.
The port type is either by design connected to another I/O Module, by user configured,
or by MM setting the port type.
Inter-Module Dual port: The port is connected to another I/O Module and can be used for both data
and management purposes. The port type is either by design connected to another I/O Module,
by user configured, or by MM setting the port type.
| ||||
| CsmFourPortCfgLinkSetting | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.4.1.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Current port link setting for Switch Module 4.
| ||||
| CsmFourPortCfgLinkState | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.4.1.1.5 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Current port link state of Switch Module 4.
| ||||
| CsmFourPortCfgSpeedSetting | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.4.1.1.6 | OCTET STRING | RW | mandatory |
column · OCTET STRING · read-write · mandatory Set the port speed using the data rate and duplex value. For examples: 100mf: 100Mbps in Half Duplex; 10gf: 10 Gbps in Full Duplex; auto: The working speed of the physical port can be tuned automatically. NOTE: Only the speeds from smFourPortCfgAvailSpeeds are applicable to setting this mib object. | ||||
| CsmFourPortCfgSpeedStatus | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.4.1.1.7 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Current port speed of Switch Module 4. | ||||
| CsmFourPortCfgAvailSpeeds | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.4.1.1.8 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Available speed setting per port for Switch Module 4. If there is more than one setting, the speeds are separated by a comma and then a space. | ||||
| CsmFourPortCfgMedia | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.4.1.1.9 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Port media type of Switch Module 4.
| ||||
| CsmFourPortCfgProtocol | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.4.1.1.10 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Port protocol of Switch Module 4.
| ||||
| CsmFourPortCfgWidth | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.4.1.1.11 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The width of the port in terms of how many combined cables are present for Switch Module 4. A value of 0 indicates this field is not applicable to the switch ports. This data is also known as the lane count. | ||||
| CsmFourPortCfgCableLength | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.4.1.1.12 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The length (in meters) of the cable supported by this port for Switch Module 4. A value of 0 indicates this field is not applicable to the switch ports. | ||||
| CsmFourPortCfgCableType | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.4.1.1.13 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory External cable type for this port, for example, active copper or passive fiber. | ||||
| CsmFourPortCfgVendorName | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.4.1.1.14 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The cable manufacturer. | ||||
| CsmFourPortCfgCompatibility | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.4.1.1.15 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Compatibility of the external cable that is plugged into the port.
| ||||
| CsmFourPortCfgDataRate | 1.3.6.1.4.1.2.3.51.2.22.3.2.2.4.1.1.16 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Data rate supported for this port.
| ||||
| NchassisTopology | 1.3.6.1.4.1.2.3.51.2.22.4 | |||
| SchassisResponseVersion | 1.3.6.1.4.1.2.3.51.2.22.4.1 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory Chassis response version. | ||||
| SchassisFlags | 1.3.6.1.4.1.2.3.51.2.22.4.2 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory Chassis flags. 1 = a server blade chassis, 0 = a rack or standalone chassis.
| ||||
| SchassisNoOfFPsSupported | 1.3.6.1.4.1.2.3.51.2.22.4.18 | INTEGER | RO | deprecated |
scalar · INTEGER · read-only · deprecated This object is deprecated because the power modules' fan packs are integrated into the power modules and are not removable as on previous power modules. Number of fan packs (FPs) supported. NOTE: Fan packs are also referred to as Power Module Cooling Devices. | ||||
| SchassisNoOfBayDevicesSupported | 1.3.6.1.4.1.2.3.51.2.22.4.19 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory Maximum number of bays found in the chassis. | ||||
| SchassisNoOfSMsSupported | 1.3.6.1.4.1.2.3.51.2.22.4.20 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory Number of switch modules (SMs) supported. | ||||
| SchassisNoOfMMsSupported | 1.3.6.1.4.1.2.3.51.2.22.4.21 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory Number of management modules (MMs) supported. | ||||
| SchassisNoOfPMsSupported | 1.3.6.1.4.1.2.3.51.2.22.4.22 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory Number of power modules (PMs) supported. | ||||
| SchassisNoOfRearLEDCardsSupported | 1.3.6.1.4.1.2.3.51.2.22.4.23 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory Number of rear LED cards supported. | ||||
| SchassisNoOfChassisFansSupported | 1.3.6.1.4.1.2.3.51.2.22.4.24 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory Number of chassis fans supported. | ||||
| SchassisBayDevicesInstalled | 1.3.6.1.4.1.2.3.51.2.22.4.25 | OCTET STRING | RO | mandatory |
scalar · OCTET STRING · read-only · mandatory The bay devices that are installed in the chassis. The bay devices are listed as a bitmap. The bitmap is a string containing a list of 1's and 0's that is as long as the number of bay devices supported. For devices that fill multiple bays, the bit mask will indicate the primary/lowest bay as occupied. If a device is installed in a bay, a 1 is present in the string in the position representing the bay ID as read from left to right. For example, if devices are installed in bays 1, 5, and 13, and 14 bays are supported, the string would look like '10001000000010'. | ||||
| SchassisSMsInstalled | 1.3.6.1.4.1.2.3.51.2.22.4.29 | OCTET STRING | RO | mandatory |
scalar · OCTET STRING · read-only · mandatory The switch modules that are installed on the chassis. The switch modules are listed as a bitmap. The bitmap is a string containing a list of 1's and 0's that is as long as the number of switch modules supported. If a switch module is installed in a bay, a 1 is present in the string in the position representing the bay ID as read from left to right. For example, if switch modules are installed in bays 1 and 3, and 4 switch modules are supported, the string would look like '1011'. | ||||
| SchassisMMsInstalled | 1.3.6.1.4.1.2.3.51.2.22.4.30 | OCTET STRING | RO | mandatory |
scalar · OCTET STRING · read-only · mandatory The management modules that are installed on the chassis. The management modules are listed as a bitmap. The bitmap is a string containing a list of 1's and 0's that is as long as the number of management modules supported. If a management module is installed in a bay, a 1 is present in the string in the position representing the bay ID as read from left to right. For example, if a management module is installed in bay 1, and 2 management modules are supported, the string would look like '10'. | ||||
| SchassisPMsInstalled | 1.3.6.1.4.1.2.3.51.2.22.4.31 | OCTET STRING | RO | mandatory |
scalar · OCTET STRING · read-only · mandatory The power modules that are installed on the chassis. The power modules are listed as a bitmap. The bitmap is a string containing a list of 1's and 0's that is as long as the number of power modules supported. If a power module is installed in a bay, a 1 is present in the string in the position representing the bay ID as read from left to right. For example, if power modules are installed in bays 1 and 3, and 4 power modules are supported, the string would look like '1010'. | ||||
| SchassisRearLEDCardInstalled | 1.3.6.1.4.1.2.3.51.2.22.4.32 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory Indicates whether at least one rear LED card is installed.
| ||||
| SchassisFansInstalled | 1.3.6.1.4.1.2.3.51.2.22.4.33 | OCTET STRING | RO | mandatory |
scalar · OCTET STRING · read-only · mandatory The chassis fans that are installed on the chassis. They are listed as a bitmap. The bitmap is a string containing a list of 1's and 0's that is as long as the number of supported. If it is installed in a bay, a 1 is present in the string in the position representing the bay ID as read from left to right. For example, if it is installed in bay 1, and 2 are supported, the string would look like '10'. | ||||
| SchassisActiveMM | 1.3.6.1.4.1.2.3.51.2.22.4.34 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory The active management module (MM). | ||||
| SchassisFPsInstalled | 1.3.6.1.4.1.2.3.51.2.22.4.37 | OCTET STRING | RO | deprecated |
scalar · OCTET STRING · read-only · deprecated This object is deprecated because the power modules' fan packs are integrated into the power modules and are not removable as on previous power modules. The fan packs that are installed on the chassis. The fan packs are listed as a bitmap. The bitmap is a string containing a list of 1's and 0's that is as long as the number of fan packs supported. If a fan pack is installed in a bay, a 1 is present in the string in the position representing the bay ID as read from left to right. For example, if fan packs are installed in bays 1 and 3, and 4 fan packs are supported, the string would look like '1010'. NOTE: Fan packs are also referred to as Power Module Cooling Devices. | ||||
| SchassisType | 1.3.6.1.4.1.2.3.51.2.22.4.38 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory The type of the chassis. This MIB object should be used in conjunction with chassisSubType MIB object to determine the characteristic of the chassis.
| ||||
| SchassisSubtype | 1.3.6.1.4.1.2.3.51.2.22.4.39 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory The subtype of the chassis. This MIB object should be used in conjunction with chassisType MIB object to determine the characteristic of the chassis.
| ||||
| SchassisNoOfRearLEDCardsInstalled | 1.3.6.1.4.1.2.3.51.2.22.4.52 | OCTET STRING | RO | mandatory |
scalar · OCTET STRING · read-only · mandatory The rear LED cards that are installed on the chassis. | ||||
| SchassisRoom | 1.3.6.1.4.1.2.3.51.2.22.4.53 | OCTET STRING (SIZE (0..24)) | RW | mandatory |
scalar · OCTET STRING (SIZE (0..24)) · read-write · mandatory The name of the room where the chassis is located. Maximum 23 characters for name plus NULL termination. | ||||
| SchassisName | 1.3.6.1.4.1.2.3.51.2.22.4.54 | OCTET STRING (SIZE (0..16)) | RW | mandatory |
scalar · OCTET STRING (SIZE (0..16)) · read-write · mandatory The name of the chassis. Maximum 15 character long plus NULL termination. | ||||
| SchassisRack | 1.3.6.1.4.1.2.3.51.2.22.4.55 | OCTET STRING (SIZE (0..24)) | RW | mandatory |
scalar · OCTET STRING (SIZE (0..24)) · read-write · mandatory The name of the room where the chassis is located. Maximum 23 characters for name plus NULL termination. | ||||
| SchassisLowestU | 1.3.6.1.4.1.2.3.51.2.22.4.56 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory The lowest U position that is occupied in the rack. | ||||
| SchassisUHeight | 1.3.6.1.4.1.2.3.51.2.22.4.57 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory The height of the chassis in 'U' units. | ||||
| NmanagementModule | 1.3.6.1.4.1.2.3.51.2.22.5 | |||
| TmmStatusTable | 1.3.6.1.4.1.2.3.51.2.22.5.1 | NA | mandatory | |
table · not-accessible · mandatory Table of the management module status. | ||||
| RmmStatusEntry | 1.3.6.1.4.1.2.3.51.2.22.5.1.1 | NA | mandatory | |
| CmmStatusIndex | 1.3.6.1.4.1.2.3.51.2.22.5.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Management module status index. | ||||
| CmmPresent | 1.3.6.1.4.1.2.3.51.2.22.5.1.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Management module current status.
| ||||
| CmmExtIpAddress | 1.3.6.1.4.1.2.3.51.2.22.5.1.1.3 | IpAddress | RO | mandatory |
column · IpAddress · read-only · mandatory Management module external IP address. NOTE: The IPv6 addresses assigned to the MM may be viewed with the extEthernetInterfaceIPv6 objects | ||||
| CmmPrimary | 1.3.6.1.4.1.2.3.51.2.22.5.1.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates if this Management module is a primary or not. NOTE: If there is no standby MM, this value defaults to primary.
| ||||
| CmmHealthState | 1.3.6.1.4.1.2.3.51.2.22.5.1.1.5 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The health state for the management module. 0 = unknown, 1 = good, 2 = warning, 3 = bad.
| ||||
| NfirmwareInformation | 1.3.6.1.4.1.2.3.51.2.22.8 | |||
| NsmFirmwareInformation | 1.3.6.1.4.1.2.3.51.2.22.8.1 | |||
| TsmFirmwareInfoTable | 1.3.6.1.4.1.2.3.51.2.22.8.1.1 | NA | mandatory | |
table · not-accessible · mandatory Switch Module firmware image information. | ||||
| RsmFirmwareInfoEntry | 1.3.6.1.4.1.2.3.51.2.22.8.1.1.1 | NA | mandatory | |
row · not-accessible · mandatory Switch Module firmware image information table entry
| ||||
| CsmFirmwareInfoIndex | 1.3.6.1.4.1.2.3.51.2.22.8.1.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Sequence index in the firmware table. | ||||
| CsmFirmwareInfoModIndex | 1.3.6.1.4.1.2.3.51.2.22.8.1.1.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Switch Module number. | ||||
| CsmFirmwareInfoImageIndex | 1.3.6.1.4.1.2.3.51.2.22.8.1.1.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Switch Module firmware image index. | ||||
| CsmFirmwareInfoImageName | 1.3.6.1.4.1.2.3.51.2.22.8.1.1.1.4 | OCTET STRING | RW | mandatory |
column · OCTET STRING · read-write · mandatory Switch Module firmware image name | ||||
| NfirmwareUpdate | 1.3.6.1.4.1.2.3.51.2.22.9 | |||
| SfirmwareUpdateTarget | 1.3.6.1.4.1.2.3.51.2.22.9.1 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Target module whose firmware will be updated. NOTE: Some switch modules do not allow firmware update. When firmware update is attempted on those switch modules, the agent will report an error.
| ||||
| SfirmwareUpdateTftpServer | 1.3.6.1.4.1.2.3.51.2.22.9.2 | OCTET STRING (SIZE (0..63)) | RW | mandatory |
scalar · OCTET STRING (SIZE (0..63)) · read-write · mandatory If flashing via the legacy method using a tftp server, then set the IP address or host name of the TFTP server where the firmware file resides. The address must be entered in a dotted decimal IP string (e.g. 9.37.44.2). NOTE: IPv6 numeric addresses must be enclosed with brackets (e.g. [fe80::5652:ff:fe50:53b6]). | ||||
| SfirmwareUpdateFileName | 1.3.6.1.4.1.2.3.51.2.22.9.3 | OCTET STRING (SIZE (0..254)) | RW | mandatory |
scalar · OCTET STRING (SIZE (0..254)) · read-write · mandatory File name of the firmware file. | ||||
| SfirmwareUpdateStart | 1.3.6.1.4.1.2.3.51.2.22.9.4 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Start updating the firmware of the specified target module. Using execute or execute-with-reboot will cause the SNMP client to wait for the firmware update to complete. Using execute-nowait or execute-with-reboot-nowait will not cause the SNMP client to wait for the update to complete. Instead it will flash the firmware in the background. Note 1: If the execute-with-reboot or execute-with-reboot-nowait option is selected, the target will reset after a successful flash. This option is only valid if the firmwareUpdateTarget object is set to managementModule. Note 2: If flashing from a remote file, then both firmwareUpdateServer and firmwareUpdateFileName must be set. Otherwise if flashing via the legacy method using a tftp server, then both firmwareUpdateTftpServer and firmwareUpdateFileName must be set. Note 3: Depending on the target, it might take up to several minutes for the flash update to complete. Do not reset the target until the control has been returned. At this point, the results will be displayed. Note 4: Use firmwareUpdateStatus to confirm the status of the last firmware update initiated by SNMP method. The Management Module must be restarted for the new firmware to take affect. Note 5: If data encryption is currently enabled on this MM, and you update the MM firmware to a level which does not support data encryption, you will lose all your configuration settings as a result. Note 6: Since some I/O Module types use the MM TFTP server for firmware file transfer during the firmware update process, the tftpEnable MIB object must be set to enable prior to updating the firmware for these modules. Note 7: If IPv6 address(es) have been configured for one or more interfaces/protocols/services on this MM, when you update the firmware to a level which does not support IPv6, all IPv6 connectivity will be lost, and services/interfaces for which an IPv6 address was configured may not function properly. You will be required to reconfigure these services/interfaces. NOTE: Value returned for the GET command is meaningless for this MIB object.
| ||||
| SfirmwareUpdateStatus | 1.3.6.1.4.1.2.3.51.2.22.9.5 | OCTET STRING | RO | mandatory |
scalar · OCTET STRING · read-only · mandatory Get the status of the last firmware update which was initiated through SNMP method. | ||||
| SstandbyFirmwareUpdateStatus | 1.3.6.1.4.1.2.3.51.2.22.9.6 | OCTET STRING | RO | mandatory |
scalar · OCTET STRING · read-only · mandatory Get the current status of the firmware update for the standby MM. NOTE: This only applies to systems with a standby MM. | ||||
| SfirmwareImageNumber | 1.3.6.1.4.1.2.3.51.2.22.9.7 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory If the module can upload more than one image, an image number must be specified after setting the firmware target. Please refer to the firmwareInformation section. | ||||
| SfirmwareActiveImage | 1.3.6.1.4.1.2.3.51.2.22.9.8 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory If the module can upload more than one image, an active image number must be specified. Please refer to the firmwareInformation section. NOTE: Value returned for the GET command is meaningless for this MIB object. | ||||
| SfirmwareUpdateServer | 1.3.6.1.4.1.2.3.51.2.22.9.9 | OCTET STRING (SIZE (0..254)) | RW | mandatory |
scalar · OCTET STRING (SIZE (0..254)) · read-write · mandatory Contains the fully qualified remote location of the firmware
packet file. Use firmwareUpdateFileName to specify the filename.
A fully qualified remote location contains a supported
protocol followed by a colon and two slashes (//), userid and
password separated by a colon for login authentication, an
@ sign, followed by the hostname or IP address of the
server where the packet file resides, followed by an optional
port number to the hostname, and the full pathname to the file.
Note that if the port number is specified, it must be
separated with the hostname (or IP address) by a colon.
The MM currently supports the following protocols:
TFTP, FTP, HTTP and HTTPS.
The complete format of a fully qualified remote location is:
<protocol>://<userid:password>@<hostname:port>/<pathname>
An example of a fully qualified remote location can be:
ftp://USERID:[email protected]:30045/tmp
where the ftp protocol will be used for transferring the file in
this location, username is USERID, password is
PASSW0RD, host IP address is 192.168.0.2, port number is
30045, and the full pathname for the packet file is /tmp.
and firmwareUpdateFileName is set to: cmefs.uxp
Some protocols do not need the username, password, and
the port number, so the minimum requirement for a fully
qualified location can be: <protocol>://<hostname>/<pathname>.
Note: When updating certain switches via SFTP, only an RSA fingerprint
is supported. Please see your switch documentation for more information. | ||||
| NfileManagement | 1.3.6.1.4.1.2.3.51.2.22.11 | |||
| NfileTopology | 1.3.6.1.4.1.2.3.51.2.22.11.1 | |||
| ScurrentDirectory | 1.3.6.1.4.1.2.3.51.2.22.11.1.1 | OCTET STRING | RW | mandatory |
scalar · OCTET STRING · read-write · mandatory Specifies the directory name for listing the requested files. | ||||
| TfileDetailsTable | 1.3.6.1.4.1.2.3.51.2.22.11.1.2 | NA | mandatory | |
table · not-accessible · mandatory A table of all the files in the specified directory. | ||||
| RfileDetailsEntry | 1.3.6.1.4.1.2.3.51.2.22.11.1.2.1 | NA | mandatory | |
| CfileIndex | 1.3.6.1.4.1.2.3.51.2.22.11.1.2.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory File sequence index. | ||||
| CfileName | 1.3.6.1.4.1.2.3.51.2.22.11.1.2.1.2 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory File name. | ||||
| CfileLastUpdate | 1.3.6.1.4.1.2.3.51.2.22.11.1.2.1.3 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Date of the latest file update. | ||||
| CfileSize | 1.3.6.1.4.1.2.3.51.2.22.11.1.2.1.4 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory File size in bytes. | ||||
| SfileManagementCmd | 1.3.6.1.4.1.2.3.51.2.22.11.3 | OCTET STRING | RW | mandatory |
scalar · OCTET STRING · read-write · mandatory This field will execute the selected operations on the files. The following operation is supported: DEL name - delete a file Examples: - to delete the file named switch.config in tftproot directory set the value to 'DEL tftproot/switch.config' NOTE: Value returned for the GET command is meaningless for this MIB object. | ||||
| SfileSystemSpaceAvailable | 1.3.6.1.4.1.2.3.51.2.22.11.6 | OCTET STRING | RO | mandatory |
scalar · OCTET STRING · read-only · mandatory This field displays the available space of the MM file system. | ||||
| NcmeRemoteChassis | 1.3.6.1.4.1.2.3.51.2.22.12 | |||
| TcmeRemoteChassisTable | 1.3.6.1.4.1.2.3.51.2.22.12.1 | NA | mandatory | |
table · not-accessible · mandatory This table is used to provide the discovered MMs based on the new, extended SLP response information. | ||||
| RcmeRemoteChassisEntry | 1.3.6.1.4.1.2.3.51.2.22.12.1.1 | NA | mandatory | |
| CcmeRemoteChassisIndex | 1.3.6.1.4.1.2.3.51.2.22.12.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Remote chassis discovery sequence index. | ||||
| CcmeSystemName | 1.3.6.1.4.1.2.3.51.2.22.12.1.1.2 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory System name for this discovery management module. | ||||
| CcmeType | 1.3.6.1.4.1.2.3.51.2.22.12.1.1.3 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Management module service processor type. | ||||
| CcmeSerial | 1.3.6.1.4.1.2.3.51.2.22.12.1.1.4 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Management module serial number. | ||||
| CcmeFru | 1.3.6.1.4.1.2.3.51.2.22.12.1.1.5 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Management module Field-Replaceable number. | ||||
| CcmeUuid | 1.3.6.1.4.1.2.3.51.2.22.12.1.1.6 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Management module UUID. | ||||
| CcmeSlot | 1.3.6.1.4.1.2.3.51.2.22.12.1.1.7 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Management module slot. | ||||
| CcmeMidPid | 1.3.6.1.4.1.2.3.51.2.22.12.1.1.8 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Management module Mid-plane Pid. | ||||
| CcmeMacAddress | 1.3.6.1.4.1.2.3.51.2.22.12.1.1.9 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Management module MAC address. | ||||
| CcmeChassisSerial | 1.3.6.1.4.1.2.3.51.2.22.12.1.1.10 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Chassis serial number. | ||||
| CcmeChassisFru | 1.3.6.1.4.1.2.3.51.2.22.12.1.1.11 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Chassis Field-Replaceable number. | ||||
| CcmeChassisMachineTypeMode | 1.3.6.1.4.1.2.3.51.2.22.12.1.1.12 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Chassis machine type and model number. | ||||
| CcmeSystemStatus | 1.3.6.1.4.1.2.3.51.2.22.12.1.1.13 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Chassis status.
| ||||
| CcmeChassisUuid | 1.3.6.1.4.1.2.3.51.2.22.12.1.1.14 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Chassis UUID. | ||||
| CcmeChassisMidPid | 1.3.6.1.4.1.2.3.51.2.22.12.1.1.15 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Chassis mid-plane ID. | ||||
| CcmeChassisId | 1.3.6.1.4.1.2.3.51.2.22.12.1.1.16 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Chassis ID. | ||||
| CcmeChassisLocation | 1.3.6.1.4.1.2.3.51.2.22.12.1.1.17 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Chassis location information. | ||||
| CcmeChassisRoomId | 1.3.6.1.4.1.2.3.51.2.22.12.1.1.18 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Chassis room ID. | ||||
| CcmeChassisRackId | 1.3.6.1.4.1.2.3.51.2.22.12.1.1.19 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Chassis rack ID. | ||||
| CcmeChassisUser | 1.3.6.1.4.1.2.3.51.2.22.12.1.1.20 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Chassis user information. | ||||
| CcmeChassisFruList | 1.3.6.1.4.1.2.3.51.2.22.12.1.1.21 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Chassis FRU list. | ||||
| CcmeFirmwareVersion | 1.3.6.1.4.1.2.3.51.2.22.12.1.1.22 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Firmware version of the discovery management module. | ||||
| CcmeChassisType | 1.3.6.1.4.1.2.3.51.2.22.12.1.1.23 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Chassis type. | ||||
| CcmeIpv4Status | 1.3.6.1.4.1.2.3.51.2.22.12.1.1.24 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory A flag to state if IPv4 is enabled
| ||||
| CcmeIpv4Addresses | 1.3.6.1.4.1.2.3.51.2.22.12.1.1.25 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The IPv4 addresses configured for the chassis. | ||||
| CcmeIpv4AddressesFloat | 1.3.6.1.4.1.2.3.51.2.22.12.1.1.26 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The floating IPv4 addresses configured for the chassis. | ||||
| CcmeIpv4Protocols | 1.3.6.1.4.1.2.3.51.2.22.12.1.1.27 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The IPv4 protocols configured for the chassis. | ||||
| CcmeIpv6Status | 1.3.6.1.4.1.2.3.51.2.22.12.1.1.28 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory A flag to state if IPv6 is enabled
| ||||
| CcmeIpv6Addresses | 1.3.6.1.4.1.2.3.51.2.22.12.1.1.29 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The IPv6 addresses configured for the chassis. | ||||
| CcmeIpv6AddressesFloat | 1.3.6.1.4.1.2.3.51.2.22.12.1.1.30 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The floating IPv6 addresses configured for the chassis. | ||||
| CcmeIpv6Protocols | 1.3.6.1.4.1.2.3.51.2.22.12.1.1.31 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The IPv6 protocols configured for the chassis. | ||||
| SchassisDiscovery | 1.3.6.1.4.1.2.3.51.2.22.12.2 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Discovery of remote Chassis. NOTE: Value returned for the GET command is meaningless for this MIB object.
| ||||
| NcomponentPower | 1.3.6.1.4.1.2.3.51.2.22.31 | |||
| TcomponentPowerTable | 1.3.6.1.4.1.2.3.51.2.22.31.1 | NA | mandatory | |
table · not-accessible · mandatory Table of component remote power control information. Contains power on/off enablement status for each component. | ||||
| RcomponentPowerEntry | 1.3.6.1.4.1.2.3.51.2.22.31.1.1 | NA | mandatory | |
| CcomponentPowerTopologyPath | 1.3.6.1.4.1.2.3.51.2.22.31.1.1.1 | OCTET STRING (SIZE (0..100)) | RO | mandatory |
column · OCTET STRING (SIZE (0..100)) · read-only · mandatory The unique identifier for a component in this table. The chassis and each installed component is represented by a hardware topology tree, where each node in the tree represents a component. The path to a particular component consists of one or more <component>,<instance> pairs, where each successive pair is a child of the previous parent pair. As an example, the root of the tree is the chassis and is represented by the pair 'CHASSIS, 1'. This pair indicates the first instance of the chassis. If a blade is inserted in slot 4 of the chassis, its topology path is 'CHASSIS, 1, BLADE, 4'. With this format, the components in the chassis can be determined along with their relative hierarchy to each other. This component table is indexed by this unique topology path and the numeric designations for the components are: CHASSIS, 0x01 Chassis MM, 0x02 Management Module BLADE, 0x03 Main system board of a blade POWER, 0x04 Power Supply, Power Module, etc COOLING, 0x05 Fan, blower, or other cooling device IO_MODULE, 0x06 Has I/O interface, i.e. - switch or bridge MEDIA, 0x07 Media device PROCESSOR, 0x08 Any processor, processor module, etc STORAGE, 0x09 Any type of storage device EXPANSION, 0x0A Expansion Card (not covered by more specific type) MEMORY, 0x0B Any memory device, module, etc MFRU, 0x0C Managed FRU Device PANEL, 0x0D Any sort of panel device, such as a front panel BLADE_EXPANSION_MODULE, 0x0E Expansion option (BEM) such as PEU, BSE, etc CARD_EXPANSION, 0x0F Expansion card, ie. daughter card CARD_HS_EXPANSION, 0x10 High Speed Expansion card, ie. daughter card INTERPOSER, 0x11 Interposer device CLOCK, 0x12 Clock card MUX, 0x13 Mulitplexer card ADDIN, 0x14 cKVM card & other addin cards STORAGE_MODULE, 0x15 Container of one or more Storage Devices SYS_EXPANSION_CARD, 0x16 Management card BATTERY, 0x17 A single battery BATTERY_MODULE, 0x18 Container of one or more batteries REAR_LED, 0x19 Rear LED card MEMORY_BANK, 0x1A Memory banks AIR_FILTER, 0x1B Filter mechanism (bezel) SERIAL_PORT_MODULE, 0x1C Container of one or more serial ports PARENT, 0x1D Reference to parent for multi-parent support PHY_PORT, 0x1E Physical port IO_EXPANDER, 0x1F RAID card CABLE, 0x20 Cable/Interconnect FAN_MUX 0x29 Fan multiplexer card PCI_EXPRESS, 0x32 PCI express card on (PEN) FLASH_DIMM, 0x33 Used for SPD devices that matches the silkscreen of the DIMM slot RACK, 0x50 Rack PLATFORM, 0x51 Generic Platform like rack mounted server/appliance DATAPLEX, 0x52 DataPlex OTHER, 0x53 Other unknown etc. PERIPHERAL_MODULE, 0x54 SYSTEM_BOARD, 0x55 System board PROCESSOR_MODULE, 0x56 BACK_PANEL, 0x57 POWER_SYSTEM_BOARD, 0x58 STORAGE_BACKPLANE, 0x59 Drive back plane PROC_BOARD, 0x5A Holds 1 or more processors POWER_DI, 0x5B Power mgt / power distribution board CHASSIS_BACK_PANEL, 0x5C SUB_CHASSIS, 0x5D OTHER_CHASSIS_BOARD, 0x5E DEVICE_MODULE, 0x5F REMOTE_DEVICE, 0x60 Remote mgt communication device EXTERNAL_ENVIRONMENT, 0x61 Such as external temp sensor for outside box temps PROC_MEMORY_MODULE, 0x62 Processors and memory on same module | ||||
| CcomponentPowerName | 1.3.6.1.4.1.2.3.51.2.22.31.1.1.2 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The name of the component as a null terminated string. | ||||
| CcomponentPowerState | 1.3.6.1.4.1.2.3.51.2.22.31.1.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates the power state of the component specified. If the state cannot be determined, the unknown(255) is returned.
| ||||
| CcomponentPowerAction | 1.3.6.1.4.1.2.3.51.2.22.31.1.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Control the power state of a specific component.
none: No action, value returned for GET.
off: Power-off component.
on: Power-on component.
softoff: Shutdown OS and power-off component. This
operation is not supported on all components.
restart: Restart a component.
restartSysMgmtProcessor:
Restart a component's system management processor.
restartNMI:
Issue a NMI (Non-Maskable Interrupt) restart to
the component. This option is not supported on all
components.
NOTE: Value returned for the GET command is meaningless
for this MIB object. The componentPowerState MIB object should be
used to check the power state of the component(s)
| ||||
| CcomponentPowerEnableSMSBootMenu | 1.3.6.1.4.1.2.3.51.2.22.31.1.1.5 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Enables/disables a component restart to the SMS boot menu. Setting this object to 'enable(1)' will cause a reboot of the node to the SMS menu. This option is not supported by all components, and at the time of this MIB definition was only supported on POWER blades.
| ||||
| ScomponentPowerTableCacheTimeout | 1.3.6.1.4.1.2.3.51.2.22.31.2 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory The timeout value (in seconds) of the cached data for the table, componentPowerTable. This value is static (constant) and cannot be set. | ||||
| TcomponentPowerDetailsTable | 1.3.6.1.4.1.2.3.51.2.22.31.6 | NA | mandatory | |
table · not-accessible · mandatory Table of component power detail information. | ||||
| RcomponentPowerDetailsEntry | 1.3.6.1.4.1.2.3.51.2.22.31.6.1 | NA | mandatory | |
row · not-accessible · mandatory Component power Details table entry | ||||
| CcomponentPowerDetailsTopologyPath | 1.3.6.1.4.1.2.3.51.2.22.31.6.1.1 | OCTET STRING (SIZE (0..100)) | RO | mandatory |
column · OCTET STRING (SIZE (0..100)) · read-only · mandatory The unique identifier for a component in this table. The chassis and each installed component is represented by a hardware topology tree, where each node in the tree represents a component. The path to a particular component consists of one or more <component>,<instance> pairs, where each successive pair is a child of the previous parent pair. As an example, the root of the tree is the chassis and is represented by the pair 'CHASSIS, 1'. This pair indicates the first instance of the chassis. If a blade is inserted in slot 4 of the chassis, its topology path is 'CHASSIS, 1, BLADE, 4'. With this format, the components in the chassis can be determined along with their relative hierarchy to each other. This component table is indexed by this unique topology path and the numeric designations for the components are: CHASSIS, 0x01 Chassis MM, 0x02 Management Module BLADE, 0x03 Main system board of a blade POWER, 0x04 Power Supply, Power Module, etc COOLING, 0x05 Fan, blower, or other cooling device IO_MODULE, 0x06 Has I/O interface, i.e. - switch or bridge MEDIA, 0x07 Media device PROCESSOR, 0x08 Any processor, processor module, etc STORAGE, 0x09 Any type of storage device EXPANSION, 0x0A Expansion Card (not covered by more specific type) MEMORY, 0x0B Any memory device, module, etc MFRU, 0x0C Managed FRU Device PANEL, 0x0D Any sort of panel device, such as a front panel BLADE_EXPANSION_MODULE, 0x0E Expansion option (BEM) such as PEU, BSE, etc CARD_EXPANSION, 0x0F Expansion card, ie. daughter card CARD_HS_EXPANSION, 0x10 High Speed Expansion card, ie. daughter card INTERPOSER, 0x11 Interposer device CLOCK, 0x12 Clock card MUX, 0x13 Mulitplexer card ADDIN, 0x14 cKVM card & other addin cards STORAGE_MODULE, 0x15 Container of one or more Storage Devices SYS_EXPANSION_CARD, 0x16 Management card BATTERY, 0x17 A single battery BATTERY_MODULE, 0x18 Container of one or more batteries REAR_LED, 0x19 Rear LED card MEMORY_BANK, 0x1A Memory banks AIR_FILTER, 0x1B Filter mechanism (bezel) SERIAL_PORT_MODULE, 0x1C Container of one or more serial ports PARENT, 0x1D Reference to parent for multi-parent support PHY_PORT, 0x1E Physical port IO_EXPANDER, 0x1F RAID card CABLE, 0x20 Cable/Interconnect FAN_MUX 0x29 Fan multiplexer card PCI_EXPRESS, 0x32 PCI express card on (PEN) FLASH_DIMM, 0x33 Used for SPD devices that matches the silkscreen of the DIMM slot RACK, 0x50 Rack PLATFORM, 0x51 Generic Platform like rack mounted server/appliance DATAPLEX, 0x52 DataPlex OTHER, 0x53 Other unknown etc. PERIPHERAL_MODULE, 0x54 SYSTEM_BOARD, 0x55 System board PROCESSOR_MODULE, 0x56 BACK_PANEL, 0x57 POWER_SYSTEM_BOARD, 0x58 STORAGE_BACKPLANE, 0x59 Drive back plane PROC_BOARD, 0x5A Holds 1 or more processors POWER_DI, 0x5B Power mgt / power distribution board CHASSIS_BACK_PANEL, 0x5C SUB_CHASSIS, 0x5D OTHER_CHASSIS_BOARD, 0x5E DEVICE_MODULE, 0x5F REMOTE_DEVICE, 0x60 Remote mgt communication device EXTERNAL_ENVIRONMENT, 0x61 Such as external temp sensor for outside box temps PROC_MEMORY_MODULE, 0x62 Processors and memory on same module | ||||
| CcomponentPowerDetailsName | 1.3.6.1.4.1.2.3.51.2.22.31.6.1.2 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The name of the component as a null terminated string. | ||||
| CcomponentPowerDetailsMaxPowerConfig | 1.3.6.1.4.1.2.3.51.2.22.31.6.1.3 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Component Module Details Table Maximum Power Configuration. Allow the user to set the maximum power that can be used by the component. This function is also known as power capping. Component must be powered on to set this value. If the value of maximum power config is zero, it means the component doesn't support the power capping feature | ||||
| CcomponentPowerDetailsEffectiveClockRate | 1.3.6.1.4.1.2.3.51.2.22.31.6.1.4 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Component Module Details Table Effective CPU Clock Rate applies to DPM components only. It displays processor's effective clock rate based on sample interval. Note that some components do not effective clock rate. In this case, 'notApplicable' will be displayed. NOTE: The effective clock rate are reported only on a primary slot when a server component spans multiple slots (e.g. double wide or triple wide). For example if the component is double wide and is installed in slot 3 and 4. 3 is primary slot while 4 is not. The effective clock rate are reported on slot 3 while 'notApplicable' is displayed for slot 4. | ||||
| CcomponentPowerDetailsMaximumClockRate | 1.3.6.1.4.1.2.3.51.2.22.31.6.1.5 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Component Module Details Table Maximum CPU Clock Rate applies to DPM components only. It displays processor's maximum clock rate based on sample interval. Note that some components do not maximum clock rate. In this case, 'notApplicable' will be displayed. NOTE: The maximum clock rate are reported only on a primary slot when a server components spans multiple slots (e.g. double wide or triple wide). For example if the component is double wide and is installed in slot 3 and 4. 3 is primary slot while 4 is not. The maximum clock rate are reported on slot 3 while 'notApplicable' is displayed for slot 4. | ||||
| CcomponentPowerDetailsPowerSaverMode | 1.3.6.1.4.1.2.3.51.2.22.31.6.1.6 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory When enabled, the static low power saver mode allows the component to selectively alter its operating voltage and frequency to reduce power consumption. This feature is not available on all component types. Please refer to the component documentation for details. If a component does not support the static low power saver mode, this object will return notApplicable (255). Under certain rare circumstances, the enabling of the static low power saver mode may not complete successfully due to interactions with other component functions, such as BIOS. Therefore, it is highly recommended that the user perform a GET of this object after performing a SET, in order to verify the completion of the intended operation. NOTE: enabling this object will disable componentPowerDetailsDynamicPowerSaver if its not already disabled.
| ||||
| CcomponentPowerDetailsDynamicPowerSaver | 1.3.6.1.4.1.2.3.51.2.22.31.6.1.7 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory When enabled, Dynamic Power Saver allows the voltage and frequency of the CPUs on the component to be controlled based on how busy the CPU is. This feature is not available on all component types. Please refer to the component documentation for details. If a component does not support the dynamic power saver, this object will return notApplicable (255). Under certain rare circumstances, the enabling of the dynamic power saver may not complete successfully due to interactions with other component functions, such as BIOS. Therefore, it is highly recommended that the user perform a GET of this object after performing a SET, in order to verify the completion of the intended operation. NOTE: enabling this object will disable componentPowerDetailsPowerSaverMode if its not already disabled.
| ||||
| CcomponentPowerDetailsDynamicPowerFavorPerformanceOverPower | 1.3.6.1.4.1.2.3.51.2.22.31.6.1.8 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory When enabled, Dynamic Power Favor Performance Over Power supports a max performance mode that pushes the system past its nominal CPU frequency when CPU and memory utilization implies it would help and the system allows it. Dynamic Power Performance Over Power can be active on the component only after Dynamic Power Saver is enabled. This feature is not available on all components types. Please refer to the component documentation for details. If a component does not support the dynamic power saver, this object will return notApplicable (255). Under certain rare circumstances, the enabling of the dynamic power favor performance over power may not complete successfully due to interactions with other component functions, such as BIOS. Therefore, it is highly recommended that the user perform a GET of this object after performing a SET, in order to verify the completion of the intended operation.
| ||||
| CcomponentPowerDetailsPowerControl | 1.3.6.1.4.1.2.3.51.2.22.31.6.1.9 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory This object is used to get or set the power control setting on a component. If dynamic power mgmt is not supported on a component, notApplicable(255) will be returned. This will set the power control setting on all slots of the multiwide component. The same can be used if the component is single wide.
| ||||
| CcomponentPowerDetailsPcapMin | 1.3.6.1.4.1.2.3.51.2.22.31.6.1.10 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Component Module Details Table power capping Minimum value in watts. The component must support the advanced power management feature. If the value of Pcap Min is 'notApplicable', it means the component doesn't support the power capping feature. If the value of Pcap Min is 'notAvailable', it means the data could not be obtained. | ||||
| CcomponentPowerDetailsPcapGuaranteedMin | 1.3.6.1.4.1.2.3.51.2.22.31.6.1.11 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Component Module Details Table power capping Guaranteed Minimum value in watts. The component must support the advanced power management feature. If the value of Pcap Guaranteed Min is 'notApplicable', it means the component doesn't support the power capping feature. If the value of Pcap GuaranteedMin is 'notAvailable', it means the data could not be obtained. | ||||
| CcomponentPowerDetailsPcapMax | 1.3.6.1.4.1.2.3.51.2.22.31.6.1.12 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Component Module Details Table power capping Maximum value in watts. The component must support the advanced power management feature. If the value is '<max1> Watts,<max2> Watts', which means, - if componentPowerDetailsDynamicPowerSaver is enabled, it is <max2> - otherwise it is <max1> If the value of Pcap Max is 'notApplicable', it means the component doesn't support the power capping feature. If the value of Pcap Min is 'notAvailable', it means the data could not be obtained. | ||||
| CcomponentPowerDetailsStaticCap | 1.3.6.1.4.1.2.3.51.2.22.31.6.1.13 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Component Module Details Table static capabilities list.
This is a list of five power management capabilities that the component
may or may not support. The list of power management capabilities is as follow:
Power Measurement
Power Capping
Power Saving
Dynamic Power Saving
Extended Dynamic Power Saving
The returned octet string contains 5 pairs of numeric characters separated by
blank characters. Each of these pairs will consist of either '00' or '01'.
'00' indicates that the capability is not there, '01' indicates that the capability
is present on the component.
The 5 pairs represent the capabilities of the 5 types listed above, in order,
for this component in the table.
Example response: '01 01 00 00 00'
This component has the capability of Power Management and Power Capping, but does not
support the last three types. | ||||
| CcomponentPowerDetailsRuntimeCap | 1.3.6.1.4.1.2.3.51.2.22.31.6.1.14 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Component Module Details Table run-time capabilities list.
If the component supports the capability as indicated in the static capability information,
the user has the ability to enable or disable that function and this table reflects that configuration.
The power management capabilites for the run-time list is as follows:
Power Measurement
Power Capping
Power Saving
Dynamic Power Saving
Extended Dynamic Power Saving
The returned octet string contains 5 pairs of numeric characters separated by
blank characters. Each of these pairs will consist of either '00' or '01'.
'00' indicates that the capability is currently not available, '01' indicates that
the capability is currently available.
The 5 pairs represent the current capabilities of the 5 types listed above, in order,
for this component in the table.
Example response: '01 00 00 00 00'
This component has the capability of Power Management only. The current state of the
component does not support the remaining 4 capabiites at this time. | ||||
| ScomponentPowerDetailsTableCacheTimeout | 1.3.6.1.4.1.2.3.51.2.22.31.7 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory The timeout value (in seconds) of the cached data for the table, componentPowerDetailsTable. This value is static (constant) and cannot be set. | ||||
| NcomponentConfiguration | 1.3.6.1.4.1.2.3.51.2.22.32 | |||
| TcomponentBayDataTable | 1.3.6.1.4.1.2.3.51.2.22.32.1 | NA | mandatory | |
table · not-accessible · mandatory Table of component bay User data information. Contains user provided data for each component bay. | ||||
| RcomponentBayDataEntry | 1.3.6.1.4.1.2.3.51.2.22.32.1.1 | NA | mandatory | |
| CcomponentBayDataTopologyPath | 1.3.6.1.4.1.2.3.51.2.22.32.1.1.1 | OCTET STRING (SIZE (0..100)) | RO | mandatory |
column · OCTET STRING (SIZE (0..100)) · read-only · mandatory The unique identifier for a component in this table. The chassis and each installed component is represented by a hardware topology tree, where each node in the tree represents a component. The path to a particular component consists of one or more <component>,<instance> pairs, where each successive pair is a child of the previous parent pair. As an example, the root of the tree is the chassis and is represented by the pair 'CHASSIS, 1'. This pair indicates the first instance of the chassis. If a blade is inserted in slot 4 of the chassis, its topology path is 'CHASSIS, 1, BLADE, 4'. With this format, the components in the chassis can be determined along with their relative hierarchy to each other. This component table is indexed by this unique topology path and the numeric designations for the components are: CHASSIS, 0x01 Chassis MM, 0x02 Management Module BLADE, 0x03 Main system board of a blade POWER, 0x04 Power Supply, Power Module, etc COOLING, 0x05 Fan, blower, or other cooling device IO_MODULE, 0x06 Has I/O interface, i.e. - switch or bridge MEDIA, 0x07 Media device PROCESSOR, 0x08 Any processor, processor module, etc STORAGE, 0x09 Any type of storage device EXPANSION, 0x0A Expansion Card (not covered by more specific type) MEMORY, 0x0B Any memory device, module, etc MFRU, 0x0C Managed FRU Device PANEL, 0x0D Any sort of panel device, such as a front panel BLADE_EXPANSION_MODULE, 0x0E Expansion option (BEM) such as PEU, BSE, etc CARD_EXPANSION, 0x0F Expansion card, ie. daughter card CARD_HS_EXPANSION, 0x10 High Speed Expansion card, ie. daughter card INTERPOSER, 0x11 Interposer device CLOCK, 0x12 Clock card MUX, 0x13 Mulitplexer card ADDIN, 0x14 cKVM card & other addin cards STORAGE_MODULE, 0x15 Container of one or more Storage Devices SYS_EXPANSION_CARD, 0x16 Management card BATTERY, 0x17 A single battery BATTERY_MODULE, 0x18 Container of one or more batteries REAR_LED, 0x19 Rear LED card MEMORY_BANK, 0x1A Memory banks AIR_FILTER, 0x1B Filter mechanism (bezel) SERIAL_PORT_MODULE, 0x1C Container of one or more serial ports PARENT, 0x1D Reference to parent for multi-parent support PHY_PORT, 0x1E Physical port IO_EXPANDER, 0x1F RAID card CABLE, 0x20 Cable/Interconnect FAN_MUX 0x29 Fan multiplexer card PCI_EXPRESS, 0x32 PCI express card on (PEN) FLASH_DIMM, 0x33 Used for SPD devices that matches the silkscreen of the DIMM slot RACK, 0x50 Rack PLATFORM, 0x51 Generic Platform like rack mounted server/appliance DATAPLEX, 0x52 DataPlex OTHER, 0x53 Other unknown etc. PERIPHERAL_MODULE, 0x54 SYSTEM_BOARD, 0x55 System board PROCESSOR_MODULE, 0x56 BACK_PANEL, 0x57 POWER_SYSTEM_BOARD, 0x58 STORAGE_BACKPLANE, 0x59 Drive back plane PROC_BOARD, 0x5A Holds 1 or more processors POWER_DI, 0x5B Power mgt / power distribution board CHASSIS_BACK_PANEL, 0x5C SUB_CHASSIS, 0x5D OTHER_CHASSIS_BOARD, 0x5E DEVICE_MODULE, 0x5F REMOTE_DEVICE, 0x60 Remote mgt communication device EXTERNAL_ENVIRONMENT, 0x61 Such as external temp sensor for outside box temps PROC_MEMORY_MODULE, 0x62 Processors and memory on same module | ||||
| CcomponentBayDataName | 1.3.6.1.4.1.2.3.51.2.22.32.1.1.2 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The name of the component as a null terminated string. | ||||
| CcomponentBayDataStatus | 1.3.6.1.4.1.2.3.51.2.22.32.1.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory This shows Bay Data (BD) Status. 0 means the component fully supports BD. 1 means that the component's BIOS does not support BD. 2 means that there is no component in the bay. 3 means that the component is being discovered. 255 means that the component does not support BBD.
| ||||
| CcomponentBayData | 1.3.6.1.4.1.2.3.51.2.22.32.1.1.4 | OCTET STRING (SIZE (0..60)) | RW | mandatory |
column · OCTET STRING (SIZE (0..60)) · read-write · mandatory A null terminated string that defines the component Bay Data. This data is puched to the components's BSMP and SMBIOS structures, where it can be used by the components's OS. Up to 60 characters can be defined plus a Null terminator. | ||||
| ScomponentBayDataTableCacheTimeout | 1.3.6.1.4.1.2.3.51.2.22.32.2 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory The timeout value (in seconds) of the cached data for the table, componentBayDataTable. This value is static (constant) and cannot be set. | ||||
| TcomponentEthOverUSBInterfaceTable | 1.3.6.1.4.1.2.3.51.2.22.32.6 | NA | mandatory | |
table · not-accessible · mandatory Table of blade Service Processor's Ethernet over USB interface. | ||||
| RcomponentEthOverUSBInterfaceEntry | 1.3.6.1.4.1.2.3.51.2.22.32.6.1 | NA | mandatory | |
row · not-accessible · mandatory Blade Service Processor's Ethernet over USB interface entry. | ||||
| CcomponentEthOverUSBInterfaceTopologyPath | 1.3.6.1.4.1.2.3.51.2.22.32.6.1.1 | OCTET STRING (SIZE (0..100)) | RO | mandatory |
column · OCTET STRING (SIZE (0..100)) · read-only · mandatory The unique identifier for a component in this table. The chassis and each installed component is represented by a hardware topology tree, where each node in the tree represents a component. The path to a particular component consists of one or more <component>,<instance> pairs, where each successive pair is a child of the previous parent pair. As an example, the root of the tree is the chassis and is represented by the pair 'CHASSIS, 1'. This pair indicates the first instance of the chassis. If a blade is inserted in slot 4 of the chassis, its topology path is 'CHASSIS, 1, BLADE, 4'. With this format, the components in the chassis can be determined along with their relative hierarchy to each other. This component table is indexed by this unique topology path and the numeric designations for the components are: CHASSIS, 0x01 Chassis MM, 0x02 Management Module BLADE, 0x03 Main system board of a blade POWER, 0x04 Power Supply, Power Module, etc COOLING, 0x05 Fan, blower, or other cooling device IO_MODULE, 0x06 Has I/O interface, i.e. - switch or bridge MEDIA, 0x07 Media device PROCESSOR, 0x08 Any processor, processor module, etc STORAGE, 0x09 Any type of storage device EXPANSION, 0x0A Expansion Card (not covered by more specific type) MEMORY, 0x0B Any memory device, module, etc MFRU, 0x0C Managed FRU Device PANEL, 0x0D Any sort of panel device, such as a front panel BLADE_EXPANSION_MODULE, 0x0E Expansion option (BEM) such as PEU, BSE, etc CARD_EXPANSION, 0x0F Expansion card, ie. daughter card CARD_HS_EXPANSION, 0x10 High Speed Expansion card, ie. daughter card INTERPOSER, 0x11 Interposer device CLOCK, 0x12 Clock card MUX, 0x13 Mulitplexer card ADDIN, 0x14 cKVM card & other addin cards STORAGE_MODULE, 0x15 Container of one or more Storage Devices SYS_EXPANSION_CARD, 0x16 Management card BATTERY, 0x17 A single battery BATTERY_MODULE, 0x18 Container of one or more batteries REAR_LED, 0x19 Rear LED card MEMORY_BANK, 0x1A Memory banks AIR_FILTER, 0x1B Filter mechanism (bezel) SERIAL_PORT_MODULE, 0x1C Container of one or more serial ports PARENT, 0x1D Reference to parent for multi-parent support PHY_PORT, 0x1E Physical port IO_EXPANDER, 0x1F RAID card CABLE, 0x20 Cable/Interconnect FAN_MUX 0x29 Fan multiplexer card PCI_EXPRESS, 0x32 PCI express card on (PEN) FLASH_DIMM, 0x33 Used for SPD devices that matches the silkscreen of the DIMM slot RACK, 0x50 Rack PLATFORM, 0x51 Generic Platform like rack mounted server/appliance DATAPLEX, 0x52 DataPlex OTHER, 0x53 Other unknown etc. PERIPHERAL_MODULE, 0x54 SYSTEM_BOARD, 0x55 System board PROCESSOR_MODULE, 0x56 BACK_PANEL, 0x57 POWER_SYSTEM_BOARD, 0x58 STORAGE_BACKPLANE, 0x59 Drive back plane PROC_BOARD, 0x5A Holds 1 or more processors POWER_DI, 0x5B Power mgt / power distribution board CHASSIS_BACK_PANEL, 0x5C SUB_CHASSIS, 0x5D OTHER_CHASSIS_BOARD, 0x5E DEVICE_MODULE, 0x5F REMOTE_DEVICE, 0x60 Remote mgt communication device EXTERNAL_ENVIRONMENT, 0x61 Such as external temp sensor for outside box temps PROC_MEMORY_MODULE, 0x62 Processors and memory on same module | ||||
| CcomponentEthOverUSBInterfaceName | 1.3.6.1.4.1.2.3.51.2.22.32.6.1.2 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The name of the component as a null terminated string. | ||||
| CcomponentEthOverUSBInterfaceEnable | 1.3.6.1.4.1.2.3.51.2.22.32.6.1.3 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory This object allows the user to view the status of, and enable or disable, a component's interface on Ethernet-over-USB. NOTE: If the component either does not exist or does not support Ethernet-over-USB command interface. It displays 'notApplicable'. NOTE: It will take about 10 or more seconds for the disable/enable setting to take effect.
| ||||
| ScomponentEthOverUSBInterfaceTableCacheTimeout | 1.3.6.1.4.1.2.3.51.2.22.32.7 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory The timeout value (in seconds) of the cached data for the table, componentEthOverUSBInterfaceTable. This value is static (constant) and cannot be set. | ||||
| TcomponentConfigurationTable | 1.3.6.1.4.1.2.3.51.2.22.32.11 | NA | mandatory | |
table · not-accessible · mandatory Table of component configuration information. | ||||
| RcomponentConfigurationEntry | 1.3.6.1.4.1.2.3.51.2.22.32.11.1 | NA | mandatory | |
row · not-accessible · mandatory Component configuration table entry | ||||
| CcomponentConfigurationTopologyPath | 1.3.6.1.4.1.2.3.51.2.22.32.11.1.1 | OCTET STRING (SIZE (0..100)) | RO | mandatory |
column · OCTET STRING (SIZE (0..100)) · read-only · mandatory The unique identifier for a component in this table. The chassis and each installed component is represented by a hardware topology tree, where each node in the tree represents a component. The path to a particular component consists of one or more <component>,<instance> pairs, where each successive pair is a child of the previous parent pair. As an example, the root of the tree is the chassis and is represented by the pair 'CHASSIS, 1'. This pair indicates the first instance of the chassis. If a blade is inserted in slot 4 of the chassis, its topology path is 'CHASSIS, 1, BLADE, 4'. With this format, the components in the chassis can be determined along with their relative hierarchy to each other. This component table is indexed by this unique topology path and the numeric designations for the components are: CHASSIS, 0x01 Chassis MM, 0x02 Management Module BLADE, 0x03 Main system board of a blade POWER, 0x04 Power Supply, Power Module, etc COOLING, 0x05 Fan, blower, or other cooling device IO_MODULE, 0x06 Has I/O interface, i.e. - switch or bridge MEDIA, 0x07 Media device PROCESSOR, 0x08 Any processor, processor module, etc STORAGE, 0x09 Any type of storage device EXPANSION, 0x0A Expansion Card (not covered by more specific type) MEMORY, 0x0B Any memory device, module, etc MFRU, 0x0C Managed FRU Device PANEL, 0x0D Any sort of panel device, such as a front panel BLADE_EXPANSION_MODULE, 0x0E Expansion option (BEM) such as PEU, BSE, etc CARD_EXPANSION, 0x0F Expansion card, ie. daughter card CARD_HS_EXPANSION, 0x10 High Speed Expansion card, ie. daughter card INTERPOSER, 0x11 Interposer device CLOCK, 0x12 Clock card MUX, 0x13 Mulitplexer card ADDIN, 0x14 cKVM card & other addin cards STORAGE_MODULE, 0x15 Container of one or more Storage Devices SYS_EXPANSION_CARD, 0x16 Management card BATTERY, 0x17 A single battery BATTERY_MODULE, 0x18 Container of one or more batteries REAR_LED, 0x19 Rear LED card MEMORY_BANK, 0x1A Memory banks AIR_FILTER, 0x1B Filter mechanism (bezel) SERIAL_PORT_MODULE, 0x1C Container of one or more serial ports PARENT, 0x1D Reference to parent for multi-parent support PHY_PORT, 0x1E Physical port IO_EXPANDER, 0x1F RAID card CABLE, 0x20 Cable/Interconnect FAN_MUX 0x29 Fan multiplexer card PCI_EXPRESS, 0x32 PCI express card on (PEN) FLASH_DIMM, 0x33 Used for SPD devices that matches the silkscreen of the DIMM slot RACK, 0x50 Rack PLATFORM, 0x51 Generic Platform like rack mounted server/appliance DATAPLEX, 0x52 DataPlex OTHER, 0x53 Other unknown etc. PERIPHERAL_MODULE, 0x54 SYSTEM_BOARD, 0x55 System board PROCESSOR_MODULE, 0x56 BACK_PANEL, 0x57 POWER_SYSTEM_BOARD, 0x58 STORAGE_BACKPLANE, 0x59 Drive back plane PROC_BOARD, 0x5A Holds 1 or more processors POWER_DI, 0x5B Power mgt / power distribution board CHASSIS_BACK_PANEL, 0x5C SUB_CHASSIS, 0x5D OTHER_CHASSIS_BOARD, 0x5E DEVICE_MODULE, 0x5F REMOTE_DEVICE, 0x60 Remote mgt communication device EXTERNAL_ENVIRONMENT, 0x61 Such as external temp sensor for outside box temps PROC_MEMORY_MODULE, 0x62 Processors and memory on same module | ||||
| CcomponentConfigurationName | 1.3.6.1.4.1.2.3.51.2.22.32.11.1.2 | OCTET STRING | RW | mandatory |
column · OCTET STRING · read-write · mandatory The name of the component as a null terminated string. This object is configurable. | ||||
| CcomponentConfigurationActiveBootMode | 1.3.6.1.4.1.2.3.51.2.22.32.11.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates the active copy of the firmware from which the component is booting. NOTE: Some components do not support the automatic boot recovery. It displays 'notApplicable' for such components. Booting from the temporary copy is recommended since it typically contains the latest enhancements and fixes. Switching to the permanent copy should be reserved for when booting from the temporary copy is no longer possible.
| ||||
| CcomponentConfigurationPendingBootMode | 1.3.6.1.4.1.2.3.51.2.22.32.11.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Indicates the copy of the firmware from which the component will boot after the next reboot. NOTE: Some components do not support the automatic boot recovery. It displays 'notApplicable' for such components and the value can not be set. Booting from the temporary copy is recommended since it typically contains the latest enhancements and fixes. Switching to the permanent copy should be reserved for when booting from the temporary copy is no longer possible.
| ||||
| CcomponentConfigurationAutoPowerOn | 1.3.6.1.4.1.2.3.51.2.22.32.11.1.5 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Component auto-power on policy. - restore: component will be powered on which were previously on. - auto: component will automatically be powered on when power is applied to the chassis. - manual: component will be left off until manually powered on by the user. - notApplicable: is a read-only value, this value cannot be set.
| ||||
| CcomponentConfigurationPowerOnRestartDelay | 1.3.6.1.4.1.2.3.51.2.22.32.11.1.6 | INTEGER (0..32767) | RW | mandatory |
column · INTEGER (0..32767) · read-write · mandatory Restart delay (in seconds) when power is applied to a component. | ||||
| CcomponentConfigurationLocalPowerControlEnable | 1.3.6.1.4.1.2.3.51.2.22.32.11.1.7 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Component local power control enablement status.
| ||||
| CcomponentConfigurationWakeOnLanControlEnable | 1.3.6.1.4.1.2.3.51.2.22.32.11.1.8 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Component Wake On LAN enablement status. If WOL is not supported by the component, it displays 'notApplicable' and WOL can not be enabled or disabled.
| ||||
| ScomponentConfigurationTableCacheTimeout | 1.3.6.1.4.1.2.3.51.2.22.32.12 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory The timeout value (in seconds) of the cached data for the table, componentConfigurationTable. This value is static (constant) and cannot be set. | ||||
| NcomponentNetworkConfiguration | 1.3.6.1.4.1.2.3.51.2.22.32.16 | |||
| TcomponentIPv4ConfigTable | 1.3.6.1.4.1.2.3.51.2.22.32.16.1 | NA | mandatory | |
table · not-accessible · mandatory Table of all components' network interfaces. | ||||
| RcomponentIPv4ConfigEntry | 1.3.6.1.4.1.2.3.51.2.22.32.16.1.1 | NA | mandatory | |
row · not-accessible · mandatory Component configuration table entry | ||||
| CcomponentIPv4ConfigTopologyPath | 1.3.6.1.4.1.2.3.51.2.22.32.16.1.1.1 | OCTET STRING (SIZE (0..100)) | RO | mandatory |
column · OCTET STRING (SIZE (0..100)) · read-only · mandatory The unique identifier for a component in this table. The chassis and each installed component is represented by a hardware topology tree, where each node in the tree represents a component. The path to a particular component consists of one or more <component>,<instance> pairs, where each successive pair is a child of the previous parent pair. As an example, the root of the tree is the chassis and is represented by the pair 'CHASSIS, 1'. This pair indicates the first instance of the chassis. If a blade is inserted in slot 4 of the chassis, its topology path is 'CHASSIS, 1, BLADE, 4'. With this format, the components in the chassis can be determined along with their relative hierarchy to each other. Note that this TP is preceded by a single octet that specifies the TP length. This is required since this table is indexed with two indices and, therefore, the TP length must be explicitly provided. This component table is indexed by this unique topology path and the numeric designations for the components are: CHASSIS, 0x01 Chassis MM, 0x02 Management Module BLADE, 0x03 Main system board of a blade POWER, 0x04 Power Supply, Power Module, etc COOLING, 0x05 Fan, blower, or other cooling device IO_MODULE, 0x06 Has I/O interface, i.e. - switch or bridge MEDIA, 0x07 Media device PROCESSOR, 0x08 Any processor, processor module, etc STORAGE, 0x09 Any type of storage device EXPANSION, 0x0A Expansion Card (not covered by more specific type) MEMORY, 0x0B Any memory device, module, etc MFRU, 0x0C Managed FRU Device PANEL, 0x0D Any sort of panel device, such as a front panel BLADE_EXPANSION_MODULE, 0x0E Expansion option (BEM) such as PEU, BSE, etc CARD_EXPANSION, 0x0F Expansion card, ie. daughter card CARD_HS_EXPANSION, 0x10 High Speed Expansion card, ie. daughter card INTERPOSER, 0x11 Interposer device CLOCK, 0x12 Clock card MUX, 0x13 Mulitplexer card ADDIN, 0x14 cKVM card & other addin cards STORAGE_MODULE, 0x15 Container of one or more Storage Devices SYS_EXPANSION_CARD, 0x16 Management card BATTERY, 0x17 A single battery BATTERY_MODULE, 0x18 Container of one or more batteries REAR_LED, 0x19 Rear LED card MEMORY_BANK, 0x1A Memory banks AIR_FILTER, 0x1B Filter mechanism (bezel) SERIAL_PORT_MODULE, 0x1C Container of one or more serial ports PARENT, 0x1D Reference to parent for multi-parent support PHY_PORT, 0x1E Physical port IO_EXPANDER, 0x1F RAID card CABLE, 0x20 Cable/Interconnect FAN_MUX 0x29 Fan multiplexer card PCI_EXPRESS, 0x32 PCI express card on (PEN) FLASH_DIMM, 0x33 Used for SPD devices that matches the silkscreen of the DIMM slot RACK, 0x50 Rack PLATFORM, 0x51 Generic Platform like rack mounted server/appliance DATAPLEX, 0x52 DataPlex OTHER, 0x53 Other unknown etc. PERIPHERAL_MODULE, 0x54 SYSTEM_BOARD, 0x55 System board PROCESSOR_MODULE, 0x56 BACK_PANEL, 0x57 POWER_SYSTEM_BOARD, 0x58 STORAGE_BACKPLANE, 0x59 Drive back plane PROC_BOARD, 0x5A Holds 1 or more processors POWER_DI, 0x5B Power mgt / power distribution board CHASSIS_BACK_PANEL, 0x5C SUB_CHASSIS, 0x5D OTHER_CHASSIS_BOARD, 0x5E DEVICE_MODULE, 0x5F REMOTE_DEVICE, 0x60 Remote mgt communication device EXTERNAL_ENVIRONMENT, 0x61 Such as external temp sensor for outside box temps PROC_MEMORY_MODULE, 0x62 Processors and memory on same module | ||||
| CcomponentIPv4ConfigPortIndex | 1.3.6.1.4.1.2.3.51.2.22.32.16.1.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The physical port number of the given entry. | ||||
| CcomponentIPv4ConfigName | 1.3.6.1.4.1.2.3.51.2.22.32.16.1.1.3 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The name of the component as a null terminated string. | ||||
| CcomponentIPv4ConfigPortLabel | 1.3.6.1.4.1.2.3.51.2.22.32.16.1.1.4 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Show string label that identifies the interface. | ||||
| CcomponentIPv4ConfigPhysicalLinkStatus | 1.3.6.1.4.1.2.3.51.2.22.32.16.1.1.5 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether this network interface port is up or down. If this network interface doesn't support up/down, show 'notApplicable(255)'.
| ||||
| CcomponentIPv4ConfigPhysicalLinkState | 1.3.6.1.4.1.2.3.51.2.22.32.16.1.1.6 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Configuration object for requesting the physical port to be either, down(0), up(1) or loopback(2). To get the current status of a physical port, use the object, componentIPv4ConfigPhysicalLinkStatus. If this network interface doesn't support up/down/loopback, show 'notApplicable(255)'.
| ||||
| CcomponentIPv4ConfigIPAddr | 1.3.6.1.4.1.2.3.51.2.22.32.16.1.1.7 | IpAddress | RW | mandatory |
column · IpAddress · read-write · mandatory Show/modify current IP address of the component network interface. Note that only if the componentIPv4ConfigPhysicalLinkStatus is 'up(1)' and the componentIPv4ConfigDHCPEnable is not 'useDhcp(1)', should the IP address be pushed down to component System Management Processor. | ||||
| CcomponentIPv4ConfigSubnetMask | 1.3.6.1.4.1.2.3.51.2.22.32.16.1.1.8 | IpAddress | RW | mandatory |
column · IpAddress · read-write · mandatory Show or modifie current subnet mask of the component network interface. Note that only if the componentIPv4ConfigPhysicalLinkStatus is 'up(1)' and the componentIPv4ConfigDHCPEnable is not 'useDhcp(1)', should the IP address be pushed down to component System Management Processor. | ||||
| CcomponentIPv4ConfigGatewayAddr | 1.3.6.1.4.1.2.3.51.2.22.32.16.1.1.9 | IpAddress | RW | mandatory |
column · IpAddress · read-write · mandatory Show or modify current IP gateway of the component network interface. Note that only if the componentIPv4ConfigPhysicalLinkStatus is 'up(1)' and the componentIPv4ConfigDHCPEnable is not 'useDhcp(1)', should the IP address be pushed down to component System Management Processor. | ||||
| CcomponentIPv4ConfigVlanId | 1.3.6.1.4.1.2.3.51.2.22.32.16.1.1.10 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory This is the Virtual LAN ID for supported network interface cards (NICs). The range of valid VLAN ID's is 0 to 4095. | ||||
| CcomponentIPv4ConfigDHCPEnable | 1.3.6.1.4.1.2.3.51.2.22.32.16.1.1.11 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory IP config method on the component network interface to modify mode to static IP, DHCP and 'try DHCP then try static'. If this network interface doesn't support DHCP, show 'notApplicable(255)'.
| ||||
| CcomponentIPv4ConfigMACAddr | 1.3.6.1.4.1.2.3.51.2.22.32.16.1.1.12 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Show the component network interface MAC address. If this network interface doesn't support MAC, show 'notApplicable'. | ||||
| ScomponentIPv4ConfigTableCacheTimeout | 1.3.6.1.4.1.2.3.51.2.22.32.16.2 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory The timeout value (in seconds) of the cached data for the table, componentIPv4ConfigTable. This value is static (constant) and cannot be set. | ||||
| NcomponentIPv6Config | 1.3.6.1.4.1.2.3.51.2.22.32.16.11 | |||
| TcomponentIPv6ConfigTable | 1.3.6.1.4.1.2.3.51.2.22.32.16.11.1 | NA | mandatory | |
table · not-accessible · mandatory A table of IPv6 configuration options for components. NOTE: This MIB object is not applicable to components that do not support IPv6. | ||||
| RcomponentIPv6ConfigEntry | 1.3.6.1.4.1.2.3.51.2.22.32.16.11.1.1 | NA | mandatory | |
row · not-accessible · mandatory IPv6 configuration options for a component. NOTE: This MIB object is not applicable to components that do not support IPv6. | ||||
| CcomponentIPv6ConfigTopologyPath | 1.3.6.1.4.1.2.3.51.2.22.32.16.11.1.1.1 | OCTET STRING (SIZE (0..100)) | RO | mandatory |
column · OCTET STRING (SIZE (0..100)) · read-only · mandatory The unique identifier for a component in this table. The chassis and each
installed component is represented by a hardware topology tree, where
each node in the tree represents a component. The path to a particular
component consists of one or more <component>,<instance> pairs, where
each successive pair is a child of the previous parent pair.
As an example, the root of the tree is the chassis and is represented
by the pair 'CHASSIS, 1'. This pair indicates the first instance of
the chassis. If a blade is inserted in slot 4 of the chassis, its
topology path is 'CHASSIS, 1, BLADE, 4'. With this format, the
components in the chassis can be determined along with their relative
hierarchy to each other.
Note that this TP is preceded by a single octet that specifies the TP length.
This is required since this table is indexed with two indices and, therefore,
the TP length must be explicitly provided.
This component table is indexed by this unique topology
path and the numeric designations for the components are:
CHASSIS, 0x01 Chassis
MM, 0x02 Management Module
BLADE, 0x03 Main system board of a blade
POWER, 0x04 Power Supply, Power Module, etc
COOLING, 0x05 Fan, blower, or other cooling device
IO_MODULE, 0x06 Has I/O interface, i.e. - switch or bridge
MEDIA, 0x07 Media device
PROCESSOR, 0x08 Any processor, processor module, etc
STORAGE, 0x09 Any type of storage device
EXPANSION, 0x0A Expansion Card (not covered by more specific type)
MEMORY, 0x0B Any memory device, module, etc
MFRU, 0x0C Managed FRU Device
PANEL, 0x0D Any sort of panel device, such as a front panel
BLADE_EXPANSION_MODULE, 0x0E Expansion option (BEM) such as PEU, BSE, etc
CARD_EXPANSION, 0x0F Expansion card, ie. daughter card
CARD_HS_EXPANSION, 0x10 High Speed Expansion card, ie. daughter card
INTERPOSER, 0x11 Interposer device
CLOCK, 0x12 Clock card
MUX, 0x13 Mulitplexer card
ADDIN, 0x14 cKVM card & other addin cards
STORAGE_MODULE, 0x15 Container of one or more Storage Devices
SYS_EXPANSION_CARD, 0x16 Management card
BATTERY, 0x17 A single battery
BATTERY_MODULE, 0x18 Container of one or more batteries
REAR_LED, 0x19 Rear LED card
MEMORY_BANK, 0x1A Memory banks
AIR_FILTER, 0x1B Filter mechanism (bezel)
SERIAL_PORT_MODULE, 0x1C Container of one or more serial ports
PARENT, 0x1D Reference to parent for multi-parent support
PHY_PORT, 0x1E Physical port
IO_EXPANDER, 0x1F RAID card
CABLE, 0x20 Cable/Interconnect
FAN_MUX 0x29 Fan multiplexer card
PCI_EXPRESS, 0x32 PCI express card on (PEN)
FLASH_DIMM, 0x33 Used for SPD devices that matches the silkscreen of the DIMM slot
RACK, 0x50 Rack
PLATFORM, 0x51 Generic Platform like rack mounted server/appliance
DATAPLEX, 0x52 DataPlex
OTHER, 0x53 Other unknown etc.
PERIPHERAL_MODULE, 0x54
SYSTEM_BOARD, 0x55 System board
PROCESSOR_MODULE, 0x56
BACK_PANEL, 0x57
POWER_SYSTEM_BOARD, 0x58
STORAGE_BACKPLANE, 0x59 Drive back plane
PROC_BOARD, 0x5A Holds 1 or more processors
POWER_DI, 0x5B Power mgt / power distribution board
CHASSIS_BACK_PANEL, 0x5C
SUB_CHASSIS, 0x5D
OTHER_CHASSIS_BOARD, 0x5E
DEVICE_MODULE, 0x5F
REMOTE_DEVICE, 0x60 Remote mgt communication device
EXTERNAL_ENVIRONMENT, 0x61 Such as external temp sensor for outside box temps
PROC_MEMORY_MODULE, 0x62 Processors and memory on same module | ||||
| CcomponentIPv6ConfigPortIndex | 1.3.6.1.4.1.2.3.51.2.22.32.16.11.1.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The physical port number of the given entry | ||||
| CcomponentIPv6ConfigName | 1.3.6.1.4.1.2.3.51.2.22.32.16.11.1.1.3 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The name of the component as a null terminated string. | ||||
| CcomponentIPv6ConfigEnabled | 1.3.6.1.4.1.2.3.51.2.22.32.16.11.1.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Enables/Disables IPv6 support on the component.
| ||||
| CcomponentIPv6ConfigStatic | 1.3.6.1.4.1.2.3.51.2.22.32.16.11.1.1.5 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Enables/Disables IPv6 static configuration support on the component.
| ||||
| CcomponentDHCPv6ConfigEnabled | 1.3.6.1.4.1.2.3.51.2.22.32.16.11.1.1.6 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Enables/Disables DHCPv6 address configuration support on the component.
| ||||
| CcomponentIPv6ConfigStatelessEnabled | 1.3.6.1.4.1.2.3.51.2.22.32.16.11.1.1.7 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Enables/Disables IPv6 stateless auto-configuration support on the component.
| ||||
| ScomponentIPv6ConfigTableCacheTimeout | 1.3.6.1.4.1.2.3.51.2.22.32.16.11.2 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory The timeout value (in seconds) of the cached data for the table, componentIPv6ConfigTable. This value is static (constant) and cannot be set. | ||||
| TcomponentIPv6AddressTable | 1.3.6.1.4.1.2.3.51.2.22.32.16.11.6 | NA | mandatory | |
table · not-accessible · mandatory A table of assigned IPv6 addresses for components. NOTE: This MIB object is not applicable to components that do not support IPv6. | ||||
| RcomponentIPv6AddressEntry | 1.3.6.1.4.1.2.3.51.2.22.32.16.11.6.1 | NA | mandatory | |
row · not-accessible · mandatory The assigned IPv6 address for a given component. NOTE: This MIB object is not applicable to components that do not support IPv6. | ||||
| CcomponentIPv6AddressTopologyPath | 1.3.6.1.4.1.2.3.51.2.22.32.16.11.6.1.1 | OCTET STRING (SIZE (0..100)) | RO | mandatory |
column · OCTET STRING (SIZE (0..100)) · read-only · mandatory The unique identifier for a component in this table. The chassis and each
installed component is represented by a hardware topology tree, where
each node in the tree represents a component. The path to a particular
component consists of one or more <component>,<instance> pairs, where
each successive pair is a child of the previous parent pair.
As an example, the root of the tree is the chassis and is represented
by the pair 'CHASSIS, 1'. This pair indicates the first instance of
the chassis. If a blade is inserted in slot 4 of the chassis, its
topology path is 'CHASSIS, 1, BLADE, 4'. With this format, the
components in the chassis can be determined along with their relative
hierarchy to each other.
Note that this TP is preceded by a single octet that specifies the TP length.
This is required since this table is indexed with multiple indices and, therefore,
the TP length must be explicitly provided.
This component table is indexed by this unique topology
path and the numeric designations for the components are:
CHASSIS, 0x01 Chassis
MM, 0x02 Management Module
BLADE, 0x03 Main system board of a blade
POWER, 0x04 Power Supply, Power Module, etc
COOLING, 0x05 Fan, blower, or other cooling device
IO_MODULE, 0x06 Has I/O interface, i.e. - switch or bridge
MEDIA, 0x07 Media device
PROCESSOR, 0x08 Any processor, processor module, etc
STORAGE, 0x09 Any type of storage device
EXPANSION, 0x0A Expansion Card (not covered by more specific type)
MEMORY, 0x0B Any memory device, module, etc
MFRU, 0x0C Managed FRU Device
PANEL, 0x0D Any sort of panel device, such as a front panel
BLADE_EXPANSION_MODULE, 0x0E Expansion option (BEM) such as PEU, BSE, etc
CARD_EXPANSION, 0x0F Expansion card, ie. daughter card
CARD_HS_EXPANSION, 0x10 High Speed Expansion card, ie. daughter card
INTERPOSER, 0x11 Interposer device
CLOCK, 0x12 Clock card
MUX, 0x13 Mulitplexer card
ADDIN, 0x14 cKVM card & other addin cards
STORAGE_MODULE, 0x15 Container of one or more Storage Devices
SYS_EXPANSION_CARD, 0x16 Management card
BATTERY, 0x17 A single battery
BATTERY_MODULE, 0x18 Container of one or more batteries
REAR_LED, 0x19 Rear LED card
MEMORY_BANK, 0x1A Memory banks
AIR_FILTER, 0x1B Filter mechanism (bezel)
SERIAL_PORT_MODULE, 0x1C Container of one or more serial ports
PARENT, 0x1D Reference to parent for multi-parent support
PHY_PORT, 0x1E Physical port
IO_EXPANDER, 0x1F RAID card
CABLE, 0x20 Cable/Interconnect
FAN_MUX 0x29 Fan multiplexer card
PCI_EXPRESS, 0x32 PCI express card on (PEN)
FLASH_DIMM, 0x33 Used for SPD devices that matches the silkscreen of the DIMM slot
RACK, 0x50 Rack
PLATFORM, 0x51 Generic Platform like rack mounted server/appliance
DATAPLEX, 0x52 DataPlex
OTHER, 0x53 Other unknown etc.
PERIPHERAL_MODULE, 0x54
SYSTEM_BOARD, 0x55 System board
PROCESSOR_MODULE, 0x56
BACK_PANEL, 0x57
POWER_SYSTEM_BOARD, 0x58
STORAGE_BACKPLANE, 0x59 Drive back plane
PROC_BOARD, 0x5A Holds 1 or more processors
POWER_DI, 0x5B Power mgt / power distribution board
CHASSIS_BACK_PANEL, 0x5C
SUB_CHASSIS, 0x5D
OTHER_CHASSIS_BOARD, 0x5E
DEVICE_MODULE, 0x5F
REMOTE_DEVICE, 0x60 Remote mgt communication device
EXTERNAL_ENVIRONMENT, 0x61 Such as external temp sensor for outside box temps
PROC_MEMORY_MODULE, 0x62 Processors and memory on same module | ||||
| CcomponentIPv6AddressPortIndex | 1.3.6.1.4.1.2.3.51.2.22.32.16.11.6.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The component's physical port number for the given entry. | ||||
| CcomponentIPv6AddressEntryIndex | 1.3.6.1.4.1.2.3.51.2.22.32.16.11.6.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The component's address entry index. | ||||
| CcomponentIPv6AddressName | 1.3.6.1.4.1.2.3.51.2.22.32.16.11.6.1.4 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The name of the component as a null terminated string. | ||||
| CcomponentIPv6AddressType | 1.3.6.1.4.1.2.3.51.2.22.32.16.11.6.1.5 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The address type.
| ||||
| CcomponentIPv6Address | 1.3.6.1.4.1.2.3.51.2.22.32.16.11.6.1.6 | InetAddressIPv6 | RW | mandatory |
column · InetAddressIPv6 · read-write · mandatory The assigned IPv6 address. Note: 'write' is for static ipv6 only. | ||||
| CcomponentIPv6AddressPrefixLen | 1.3.6.1.4.1.2.3.51.2.22.32.16.11.6.1.7 | INTEGER (1..128) | RW | mandatory |
column · INTEGER (1..128) · read-write · mandatory The prefix length for the given address. Note: 'write' is for static ipv6 only. | ||||
| CcomponentIPv6AddressDefaultRoute | 1.3.6.1.4.1.2.3.51.2.22.32.16.11.6.1.8 | InetAddressIPv6 | RW | mandatory |
column · InetAddressIPv6 · read-write · mandatory The default route used for the given address. Note: 'write' is for static ipv6 only. | ||||
| ScomponentIPv6AddressTableCacheTimeout | 1.3.6.1.4.1.2.3.51.2.22.32.16.11.7 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory The timeout value (in seconds) of the cached data for the table, componentIPv6AddressTable. This value is static (constant) and cannot be set. | ||||
| TcomponentTimeTable | 1.3.6.1.4.1.2.3.51.2.22.32.20 | NA | mandatory | |
table · not-accessible · mandatory Table of Component NTP Configuration. | ||||
| RcomponentTimeEntry | 1.3.6.1.4.1.2.3.51.2.22.32.20.1 | NA | mandatory | |
| CcomponentTimeTopologyPath | 1.3.6.1.4.1.2.3.51.2.22.32.20.1.1 | OCTET STRING (SIZE (0..100)) | RO | mandatory |
column · OCTET STRING (SIZE (0..100)) · read-only · mandatory The unique identifier for a component in this table. The chassis and each installed component is represented by a hardware topology tree, where each node in the tree represents a component. The path to a particular component consists of one or more <component>,<instance> pairs, where each successive pair is a child of the previous parent pair. As an example, the root of the tree is the chassis and is represented by the pair 'CHASSIS, 1'. This pair indicates the first instance of the chassis. If a blade is inserted in slot 4 of the chassis, its topology path is 'CHASSIS, 1, BLADE, 4'. With this format, the components in the chassis can be determined along with their relative hierarchy to each other. This component table is indexed by this unique topology path and the numeric designations for the components are: CHASSIS, 0x01 Chassis MM, 0x02 Management Module BLADE, 0x03 Main system board of a blade POWER, 0x04 Power Supply, Power Module, etc COOLING, 0x05 Fan, blower, or other cooling device IO_MODULE, 0x06 Has I/O interface, i.e. - switch or bridge MEDIA, 0x07 Media device PROCESSOR, 0x08 Any processor, processor module, etc STORAGE, 0x09 Any type of storage device EXPANSION, 0x0A Expansion Card (not covered by more specific type) MEMORY, 0x0B Any memory device, module, etc MFRU, 0x0C Managed FRU Device PANEL, 0x0D Any sort of panel device, such as a front panel BLADE_EXPANSION_MODULE, 0x0E Expansion option (BEM) such as PEU, BSE, etc CARD_EXPANSION, 0x0F Expansion card, ie. daughter card CARD_HS_EXPANSION, 0x10 High Speed Expansion card, ie. daughter card INTERPOSER, 0x11 Interposer device CLOCK, 0x12 Clock card MUX, 0x13 Mulitplexer card ADDIN, 0x14 cKVM card & other addin cards STORAGE_MODULE, 0x15 Container of one or more Storage Devices SYS_EXPANSION_CARD, 0x16 Management card BATTERY, 0x17 A single battery BATTERY_MODULE, 0x18 Container of one or more batteries REAR_LED, 0x19 Rear LED card MEMORY_BANK, 0x1A Memory banks AIR_FILTER, 0x1B Filter mechanism (bezel) SERIAL_PORT_MODULE, 0x1C Container of one or more serial ports PARENT, 0x1D Reference to parent for multi-parent support PHY_PORT, 0x1E Physical port IO_EXPANDER, 0x1F RAID card CABLE, 0x20 Cable/Interconnect FAN_MUX 0x29 Fan multiplexer card PCI_EXPRESS, 0x32 PCI express card on (PEN) FLASH_DIMM, 0x33 Used for SPD devices that matches the silkscreen of the DIMM slot RACK, 0x50 Rack PLATFORM, 0x51 Generic Platform like rack mounted server/appliance DATAPLEX, 0x52 DataPlex OTHER, 0x53 Other unknown etc. PERIPHERAL_MODULE, 0x54 SYSTEM_BOARD, 0x55 System board PROCESSOR_MODULE, 0x56 BACK_PANEL, 0x57 POWER_SYSTEM_BOARD, 0x58 STORAGE_BACKPLANE, 0x59 Drive back plane PROC_BOARD, 0x5A Holds 1 or more processors POWER_DI, 0x5B Power mgt / power distribution board CHASSIS_BACK_PANEL, 0x5C SUB_CHASSIS, 0x5D OTHER_CHASSIS_BOARD, 0x5E DEVICE_MODULE, 0x5F REMOTE_DEVICE, 0x60 Remote mgt communication device EXTERNAL_ENVIRONMENT, 0x61 Such as external temp sensor for outside box temps PROC_MEMORY_MODULE, 0x62 Processors and memory on same module | ||||
| CcomponentTimeName | 1.3.6.1.4.1.2.3.51.2.22.32.20.1.2 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The name of the component as a null terminated string. | ||||
| CcomponentTimeNTPEnable | 1.3.6.1.4.1.2.3.51.2.22.32.20.1.3 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory This object allows the user to view the status of, and enable or disable, a component's ability to have it's NTP information updated by the CMM. NOTE: If the component either does not exist or does not support this feature, it displays 'notApplicable'.
| ||||
| CcomponentTimeNTPFrequency | 1.3.6.1.4.1.2.3.51.2.22.32.20.1.4 | INTEGER (0..44640) | RW | mandatory |
column · INTEGER (0..44640) · read-write · mandatory This object allows the user to view or set the synchronization frequency (in minutes) of the NTP information update from the CMM. NOTE: If the component either does not exist or does not support this feature, it displays '0'. | ||||
| ScomponentTimeTableCacheTimeout | 1.3.6.1.4.1.2.3.51.2.22.32.21 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory The timeout value (in seconds) of the cached data for the table, componentTimeTable. This value is static (constant) and cannot be set. | ||||
| TcomponentSolTable | 1.3.6.1.4.1.2.3.51.2.22.32.26 | NA | mandatory | |
table · not-accessible · mandatory Component Serial-over-LAN (SOL) configuration table. | ||||
| RcomponentSolEntry | 1.3.6.1.4.1.2.3.51.2.22.32.26.1 | NA | mandatory | |
row · not-accessible · mandatory Component Serial-over-LAN (SOL) configuration entry. | ||||
| CcomponentSolTopologyPath | 1.3.6.1.4.1.2.3.51.2.22.32.26.1.1 | OCTET STRING (SIZE (0..100)) | RO | mandatory |
column · OCTET STRING (SIZE (0..100)) · read-only · mandatory The unique identifier for a component in this table. The chassis and each installed component is represented by a hardware topology tree, where each node in the tree represents a component. The path to a particular component consists of one or more <component>,<instance> pairs, where each successive pair is a child of the previous parent pair. As an example, the root of the tree is the chassis and is represented by the pair 'CHASSIS, 1'. This pair indicates the first instance of the chassis. If a blade is inserted in slot 4 of the chassis, its topology path is 'CHASSIS, 1, BLADE, 4'. With this format, the components in the chassis can be determined along with their relative hierarchy to each other. This component table is indexed by this unique topology path and the numeric designations for the components are: CHASSIS, 0x01 Chassis MM, 0x02 Management Module BLADE, 0x03 Main system board of a blade POWER, 0x04 Power Supply, Power Module, etc COOLING, 0x05 Fan, blower, or other cooling device IO_MODULE, 0x06 Has I/O interface, i.e. - switch or bridge MEDIA, 0x07 Media device PROCESSOR, 0x08 Any processor, processor module, etc STORAGE, 0x09 Any type of storage device EXPANSION, 0x0A Expansion Card (not covered by more specific type) MEMORY, 0x0B Any memory device, module, etc MFRU, 0x0C Managed FRU Device PANEL, 0x0D Any sort of panel device, such as a front panel BLADE_EXPANSION_MODULE, 0x0E Expansion option (BEM) such as PEU, BSE, etc CARD_EXPANSION, 0x0F Expansion card, ie. daughter card CARD_HS_EXPANSION, 0x10 High Speed Expansion card, ie. daughter card INTERPOSER, 0x11 Interposer device CLOCK, 0x12 Clock card MUX, 0x13 Mulitplexer card ADDIN, 0x14 cKVM card & other addin cards STORAGE_MODULE, 0x15 Container of one or more Storage Devices SYS_EXPANSION_CARD, 0x16 Management card BATTERY, 0x17 A single battery BATTERY_MODULE, 0x18 Container of one or more batteries REAR_LED, 0x19 Rear LED card MEMORY_BANK, 0x1A Memory banks AIR_FILTER, 0x1B Filter mechanism (bezel) SERIAL_PORT_MODULE, 0x1C Container of one or more serial ports PARENT, 0x1D Reference to parent for multi-parent support PHY_PORT, 0x1E Physical port IO_EXPANDER, 0x1F RAID card CABLE, 0x20 Cable/Interconnect FAN_MUX 0x29 Fan multiplexer card PCI_EXPRESS, 0x32 PCI express card on (PEN) FLASH_DIMM, 0x33 Used for SPD devices that matches the silkscreen of the DIMM slot RACK, 0x50 Rack PLATFORM, 0x51 Generic Platform like rack mounted server/appliance DATAPLEX, 0x52 DataPlex OTHER, 0x53 Other unknown etc. PERIPHERAL_MODULE, 0x54 SYSTEM_BOARD, 0x55 System board PROCESSOR_MODULE, 0x56 BACK_PANEL, 0x57 POWER_SYSTEM_BOARD, 0x58 STORAGE_BACKPLANE, 0x59 Drive back plane PROC_BOARD, 0x5A Holds 1 or more processors POWER_DI, 0x5B Power mgt / power distribution board CHASSIS_BACK_PANEL, 0x5C SUB_CHASSIS, 0x5D OTHER_CHASSIS_BOARD, 0x5E DEVICE_MODULE, 0x5F REMOTE_DEVICE, 0x60 Remote mgt communication device EXTERNAL_ENVIRONMENT, 0x61 Such as external temp sensor for outside box temps PROC_MEMORY_MODULE, 0x62 Processors and memory on same module | ||||
| CcomponentSolName | 1.3.6.1.4.1.2.3.51.2.22.32.26.1.2 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The name of the component as a null terminated string. | ||||
| CcomponentSolEnable | 1.3.6.1.4.1.2.3.51.2.22.32.26.1.3 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Disable or enable the Serial-over-LAN (SOL) on a component.
| ||||
| CcomponentSolIpAddr | 1.3.6.1.4.1.2.3.51.2.22.32.26.1.4 | IpAddress | RO | deprecated |
column · IpAddress · read-only · deprecated This is deprecated in favor of componentSolIpAddr.
IP address of the component derived from the IP address
range for the system management processors on the
component.
NOTE: The IPv6 address for a component can be view with the
componentIPv6AddressTable. | ||||
| CcomponentSolSessionStatus | 1.3.6.1.4.1.2.3.51.2.22.32.26.1.5 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Status of a Serial-over-LAN (SOL) session:
solSessionNotReady: No SOL session connected to the
component.
solSessionReady: There is a SOL session to the
component.
solSessionActive: There is a SOL session to the
component and there is a client
using the SOL session.
| ||||
| CcomponentSolCapability | 1.3.6.1.4.1.2.3.51.2.22.32.26.1.6 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Display whether or not the component supports the Serial-over-LAN (SOL) feature.
| ||||
| CcomponentSolIpAddr6 | 1.3.6.1.4.1.2.3.51.2.22.32.26.1.7 | InetAddressIPv6 | RO | mandatory |
column · InetAddressIPv6 · read-only · mandatory IPv6 address of the blade. | ||||
| CcomponentSolRetryInterval | 1.3.6.1.4.1.2.3.51.2.22.32.26.1.8 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Retry interval time in miliseconds. | ||||
| CcomponentSolRetryCount | 1.3.6.1.4.1.2.3.51.2.22.32.26.1.9 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Retry count. | ||||
| CcomponentSolBytesSent | 1.3.6.1.4.1.2.3.51.2.22.32.26.1.10 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Number of bytes sent. | ||||
| CcomponentSolBytesReceived | 1.3.6.1.4.1.2.3.51.2.22.32.26.1.11 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Number of bytes received. | ||||
| CcomponentSolDestinationMAC | 1.3.6.1.4.1.2.3.51.2.22.32.26.1.12 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory MAC address of the blade. | ||||
| CcomponentSolConsoleUserId | 1.3.6.1.4.1.2.3.51.2.22.32.26.1.13 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Sol console user name. | ||||
| CcomponentSolConsoleLoginFrom | 1.3.6.1.4.1.2.3.51.2.22.32.26.1.14 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The location information from where the SOL console is logged in. | ||||
| CcomponentSolConsoleLoginStart | 1.3.6.1.4.1.2.3.51.2.22.32.26.1.15 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The time that SOL console starts. | ||||
| CcomponentSolConsoleLoginEnd | 1.3.6.1.4.1.2.3.51.2.22.32.26.1.16 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The time that SOL console ends. | ||||
| ScomponentSolTableCacheTimeout | 1.3.6.1.4.1.2.3.51.2.22.32.27 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory The timeout value (in seconds) of the cached data for the table, componentSolTable. This value is static (constant) and cannot be set. | ||||
| NcomponentMonitors | 1.3.6.1.4.1.2.3.51.2.22.37 | |||
| TcomponentSystemStatusTable | 1.3.6.1.4.1.2.3.51.2.22.37.1 | NA | mandatory | |
table · not-accessible · mandatory Table of component status information. | ||||
| RcomponentSystemStatusEntry | 1.3.6.1.4.1.2.3.51.2.22.37.1.1 | NA | mandatory | |
| CcomponentStatusTopologyPath | 1.3.6.1.4.1.2.3.51.2.22.37.1.1.1 | OCTET STRING (SIZE (0..100)) | RO | mandatory |
column · OCTET STRING (SIZE (0..100)) · read-only · mandatory The unique identifier for a component in this table. The chassis and each installed component is represented by a hardware topology tree, where each node in the tree represents a component. The path to a particular component consists of one or more <component>,<instance> pairs, where each successive pair is a child of the previous parent pair. As an example, the root of the tree is the chassis and is represented by the pair 'CHASSIS, 1'. This pair indicates the first instance of the chassis. If a blade is inserted in slot 4 of the chassis, its topology path is 'CHASSIS, 1, BLADE, 4'. With this format, the components in the chassis can be determined along with their relative hierarchy to each other. This component table is indexed by this unique topology path and the numeric designations for the components are: CHASSIS, 0x01 Chassis MM, 0x02 Management Module BLADE, 0x03 Main system board of a blade POWER, 0x04 Power Supply, Power Module, etc COOLING, 0x05 Fan, blower, or other cooling device IO_MODULE, 0x06 Has I/O interface, i.e. - switch or bridge MEDIA, 0x07 Media device PROCESSOR, 0x08 Any processor, processor module, etc STORAGE, 0x09 Any type of storage device EXPANSION, 0x0A Expansion Card (not covered by more specific type) MEMORY, 0x0B Any memory device, module, etc MFRU, 0x0C Managed FRU Device PANEL, 0x0D Any sort of panel device, such as a front panel BLADE_EXPANSION_MODULE, 0x0E Expansion option (BEM) such as PEU, BSE, etc CARD_EXPANSION, 0x0F Expansion card, ie. daughter card CARD_HS_EXPANSION, 0x10 High Speed Expansion card, ie. daughter card INTERPOSER, 0x11 Interposer device CLOCK, 0x12 Clock card MUX, 0x13 Mulitplexer card ADDIN, 0x14 cKVM card & other addin cards STORAGE_MODULE, 0x15 Container of one or more Storage Devices SYS_EXPANSION_CARD, 0x16 Management card BATTERY, 0x17 A single battery BATTERY_MODULE, 0x18 Container of one or more batteries REAR_LED, 0x19 Rear LED card MEMORY_BANK, 0x1A Memory banks AIR_FILTER, 0x1B Filter mechanism (bezel) SERIAL_PORT_MODULE, 0x1C Container of one or more serial ports PARENT, 0x1D Reference to parent for multi-parent support PHY_PORT, 0x1E Physical port IO_EXPANDER, 0x1F RAID card CABLE, 0x20 Cable/Interconnect FAN_MUX 0x29 Fan multiplexer card PCI_EXPRESS, 0x32 PCI express card on (PEN) FLASH_DIMM, 0x33 Used for SPD devices that matches the silkscreen of the DIMM slot RACK, 0x50 Rack PLATFORM, 0x51 Generic Platform like rack mounted server/appliance DATAPLEX, 0x52 DataPlex OTHER, 0x53 Other unknown etc. PERIPHERAL_MODULE, 0x54 SYSTEM_BOARD, 0x55 System board PROCESSOR_MODULE, 0x56 BACK_PANEL, 0x57 POWER_SYSTEM_BOARD, 0x58 STORAGE_BACKPLANE, 0x59 Drive back plane PROC_BOARD, 0x5A Holds 1 or more processors POWER_DI, 0x5B Power mgt / power distribution board CHASSIS_BACK_PANEL, 0x5C SUB_CHASSIS, 0x5D OTHER_CHASSIS_BOARD, 0x5E DEVICE_MODULE, 0x5F REMOTE_DEVICE, 0x60 Remote mgt communication device EXTERNAL_ENVIRONMENT, 0x61 Such as external temp sensor for outside box temps PROC_MEMORY_MODULE, 0x62 Processors and memory on same module | ||||
| CcomponentStatusName | 1.3.6.1.4.1.2.3.51.2.22.37.1.1.2 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The name of the component as a null terminated string. | ||||
| CcomponentStatusPowerState | 1.3.6.1.4.1.2.3.51.2.22.37.1.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates the power state of the component specified.
| ||||
| CcomponentStatusHealthState | 1.3.6.1.4.1.2.3.51.2.22.37.1.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The system health state for the component. Unknown: Component is in an undefined state. Good: Component is operating normally. Warning: One or more outstanding warnings exist for this component. Critical: One or more outstanding critical events for this component. Kernel Mode: Component is in kernel mode. Discovering: The MM is currently in the process of discovering this component. Communications Error: The MM failed to communicate with this component. No Power: No power to the component's domain. Flashing: Flashing in progress. Initialization Failure: Component failed to initialized. Insufficient Power: Not enough power is left in the component's domain to power the component. Power Denied: Power was denied to the component.
| ||||
| CcomponentStatusPowerEnable | 1.3.6.1.4.1.2.3.51.2.22.37.1.1.5 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Power enable state for the component.
| ||||
| CcomponentStatusWakeOnLanEnable | 1.3.6.1.4.1.2.3.51.2.22.37.1.1.6 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Wake on LAN enable state for the component.
| ||||
| CcomponentStatusWidth | 1.3.6.1.4.1.2.3.51.2.22.37.1.1.7 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The width of the component including any supplement component attached to it | ||||
| CcomponentStatusIOCompatibility | 1.3.6.1.4.1.2.3.51.2.22.37.1.1.21 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory I/O compatibility status for the component.
The possible values and their meanings are as follows:
unknown: This indicates a communication error for the component.
ok: This is the normal (good) case where the component and the
corresponding I/O modules it is internally wired to have no
compatibility issues.
noIOMs: This means there are no I/O modules in any of the
corresponding I/O module bays this component is internally wired to.
attention: This indicates that one or more of the corresponding
I/O modules are in communication error.
mismatch: This indicates one of the following cases:
Fabric types are incompatible
An unknown I/O module type
An unknown fabric type on the component | ||||
| CcomponentStatusInventoryReady | 1.3.6.1.4.1.2.3.51.2.22.37.1.1.22 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory When a component management controller or the MM is reset, the component inventory data is refreshed in the MM database. This includes items like IBM VPD (e.g. - serial number, UUID) and MAC address information. Applications need to know when this information has been populated on the MM before they begin to query it using SNMP or other means. This simple flag object will return a ready or notReady indication for each component regarding the status of this information. Notes: For components that are experiencing a 'communication failure' or 'initialization failure' condition, this object will continue to indicate notReady until the condition is resolved. Therefore, any application that polls this object should also incorporate a timeout period.
| ||||
| CcomponentStatusBootCountPowerOnTimeBoots | 1.3.6.1.4.1.2.3.51.2.22.37.1.1.23 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Blade boot count. This is valid for blade components and otherwise is undefined. Writing this value resets the boot count to zero. | ||||
| CcomponentStatusBootCountPowerOnTimeSecs | 1.3.6.1.4.1.2.3.51.2.22.37.1.1.24 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Blade power on time in seconds. This is valid for blade components and otherwise is undefined. Writing this value resets the power on time to zero. | ||||
| ScomponentSystemStatusTableCacheTimeout | 1.3.6.1.4.1.2.3.51.2.22.37.2 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory The timeout value (in seconds) of the cached data for the table, componentSystemStatusTable. This value is static (constant) and cannot be set. | ||||
| TcomponentHealthSummaryTable | 1.3.6.1.4.1.2.3.51.2.22.37.6 | NA | mandatory | |
table · not-accessible · mandatory Table of component health summary information. Contains information about the overall component health status. Each component contains a list of critical or warning events for that component or severity of good or none if none exist. | ||||
| RcomponentHealthSummaryEntry | 1.3.6.1.4.1.2.3.51.2.22.37.6.1 | NA | mandatory | |
row · not-accessible · mandatory Component health summary entry | ||||
| CcomponentHealthTopologyPath | 1.3.6.1.4.1.2.3.51.2.22.37.6.1.1 | OCTET STRING (SIZE (0..100)) | RO | mandatory |
column · OCTET STRING (SIZE (0..100)) · read-only · mandatory The unique identifier for a component in this table. The chassis and each installed component is represented by a hardware topology tree, where each node in the tree represents a component. The path to a particular component consists of one or more <component>,<instance> pairs, where each successive pair is a child of the previous parent pair. As an example, the root of the tree is the chassis and is represented by the pair 'CHASSIS, 1'. This pair indicates the first instance of the chassis. If a blade is inserted in slot 4 of the chassis, its topology path is 'CHASSIS, 1, BLADE, 4'. With this format, the components in the chassis can be determined along with their relative hierarchy to each other. Note that this TP is preceded by a single octet that specifies the TP length. This is required since this table is indexed with two indices and, therefore, the TP length must be explicitly provided. This component table is indexed by this unique topology path and the numeric designations for the components are: CHASSIS, 0x01 Chassis MM, 0x02 Management Module BLADE, 0x03 Main system board of a blade POWER, 0x04 Power Supply, Power Module, etc COOLING, 0x05 Fan, blower, or other cooling device IO_MODULE, 0x06 Has I/O interface, i.e. - switch or bridge MEDIA, 0x07 Media device PROCESSOR, 0x08 Any processor, processor module, etc STORAGE, 0x09 Any type of storage device EXPANSION, 0x0A Expansion Card (not covered by more specific type) MEMORY, 0x0B Any memory device, module, etc MFRU, 0x0C Managed FRU Device PANEL, 0x0D Any sort of panel device, such as a front panel BLADE_EXPANSION_MODULE, 0x0E Expansion option (BEM) such as PEU, BSE, etc CARD_EXPANSION, 0x0F Expansion card, ie. daughter card CARD_HS_EXPANSION, 0x10 High Speed Expansion card, ie. daughter card INTERPOSER, 0x11 Interposer device CLOCK, 0x12 Clock card MUX, 0x13 Mulitplexer card ADDIN, 0x14 cKVM card & other addin cards STORAGE_MODULE, 0x15 Container of one or more Storage Devices SYS_EXPANSION_CARD, 0x16 Management card BATTERY, 0x17 A single battery BATTERY_MODULE, 0x18 Container of one or more batteries REAR_LED, 0x19 Rear LED card MEMORY_BANK, 0x1A Memory banks AIR_FILTER, 0x1B Filter mechanism (bezel) SERIAL_PORT_MODULE, 0x1C Container of one or more serial ports PARENT, 0x1D Reference to parent for multi-parent support PHY_PORT, 0x1E Physical port IO_EXPANDER, 0x1F RAID card CABLE, 0x20 Cable/Interconnect FAN_MUX 0x29 Fan multiplexer card PCI_EXPRESS, 0x32 PCI express card on (PEN) FLASH_DIMM, 0x33 Used for SPD devices that matches the silkscreen of the DIMM slot RACK, 0x50 Rack PLATFORM, 0x51 Generic Platform like rack mounted server/appliance DATAPLEX, 0x52 DataPlex OTHER, 0x53 Other unknown etc. PERIPHERAL_MODULE, 0x54 SYSTEM_BOARD, 0x55 System board PROCESSOR_MODULE, 0x56 BACK_PANEL, 0x57 POWER_SYSTEM_BOARD, 0x58 STORAGE_BACKPLANE, 0x59 Drive back plane PROC_BOARD, 0x5A Holds 1 or more processors POWER_DI, 0x5B Power mgt / power distribution board CHASSIS_BACK_PANEL, 0x5C SUB_CHASSIS, 0x5D OTHER_CHASSIS_BOARD, 0x5E DEVICE_MODULE, 0x5F REMOTE_DEVICE, 0x60 Remote mgt communication device EXTERNAL_ENVIRONMENT, 0x61 Such as external temp sensor for outside box temps PROC_MEMORY_MODULE, 0x62 Processors and memory on same module | ||||
| CcomponentHealthEventIndex | 1.3.6.1.4.1.2.3.51.2.22.37.6.1.2 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory An index for the critical or warning health events for a given component. | ||||
| CcomponentHealthSummaryName | 1.3.6.1.4.1.2.3.51.2.22.37.6.1.3 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The name of the component as a null terminated string. | ||||
| CcomponentHealthSummarySeverity | 1.3.6.1.4.1.2.3.51.2.22.37.6.1.4 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory System health summary severity of an event for the given component. | ||||
| CcomponentHealthSummaryDescription | 1.3.6.1.4.1.2.3.51.2.22.37.6.1.5 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory System health summary description of an event for the given component. | ||||
| CcomponentHealthSummaryDateTime | 1.3.6.1.4.1.2.3.51.2.22.37.6.1.6 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory System health summary date time of an event for the given component. | ||||
| CcomponentHealthSummaryEventID | 1.3.6.1.4.1.2.3.51.2.22.37.6.1.7 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory System health summary event ID of an event for the given component. | ||||
| ScomponentHealthSummaryTableCacheTimeout | 1.3.6.1.4.1.2.3.51.2.22.37.7 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory The timeout value (in seconds) of the cached data for the table, componentHealthSummaryTable. This value is static (constant) and cannot be set. | ||||
| TcomponentMACAddressTable | 1.3.6.1.4.1.2.3.51.2.22.37.11 | NA | mandatory | |
table · not-accessible · mandatory Table of MAC address VPD information for each component. | ||||
| RcomponentMACAddressEntry | 1.3.6.1.4.1.2.3.51.2.22.37.11.1 | NA | mandatory | |
row · not-accessible · mandatory Component MAC address table entry | ||||
| CcomponentMACAddressTopologyPath | 1.3.6.1.4.1.2.3.51.2.22.37.11.1.1 | OCTET STRING (SIZE (0..100)) | RO | mandatory |
column · OCTET STRING (SIZE (0..100)) · read-only · mandatory The unique identifier for a component in this table. The chassis and each installed component is represented by a hardware topology tree, where each node in the tree represents a component. The path to a particular component consists of one or more <component>,<instance> pairs, where each successive pair is a child of the previous parent pair. As an example, the root of the tree is the chassis and is represented by the pair 'CHASSIS, 1'. This pair indicates the first instance of the chassis. If a blade is inserted in slot 4 of the chassis, its topology path is 'CHASSIS, 1, BLADE, 4'. With this format, the components in the chassis can be determined along with their relative hierarchy to each other. Note that this TP is preceded by a single octet that specifies the TP length. This is required since this table is indexed with two indices and, therefore, the TP length must be explicitly provided. This component table is indexed by this unique topology path and the numeric designations for the components are: CHASSIS, 0x01 Chassis MM, 0x02 Management Module BLADE, 0x03 Main system board of a blade POWER, 0x04 Power Supply, Power Module, etc COOLING, 0x05 Fan, blower, or other cooling device IO_MODULE, 0x06 Has I/O interface, i.e. - switch or bridge MEDIA, 0x07 Media device PROCESSOR, 0x08 Any processor, processor module, etc STORAGE, 0x09 Any type of storage device EXPANSION, 0x0A Expansion Card (not covered by more specific type) MEMORY, 0x0B Any memory device, module, etc MFRU, 0x0C Managed FRU Device PANEL, 0x0D Any sort of panel device, such as a front panel BLADE_EXPANSION_MODULE, 0x0E Expansion option (BEM) such as PEU, BSE, etc CARD_EXPANSION, 0x0F Expansion card, ie. daughter card CARD_HS_EXPANSION, 0x10 High Speed Expansion card, ie. daughter card INTERPOSER, 0x11 Interposer device CLOCK, 0x12 Clock card MUX, 0x13 Mulitplexer card ADDIN, 0x14 cKVM card & other addin cards STORAGE_MODULE, 0x15 Container of one or more Storage Devices SYS_EXPANSION_CARD, 0x16 Management card BATTERY, 0x17 A single battery BATTERY_MODULE, 0x18 Container of one or more batteries REAR_LED, 0x19 Rear LED card MEMORY_BANK, 0x1A Memory banks AIR_FILTER, 0x1B Filter mechanism (bezel) SERIAL_PORT_MODULE, 0x1C Container of one or more serial ports PARENT, 0x1D Reference to parent for multi-parent support PHY_PORT, 0x1E Physical port IO_EXPANDER, 0x1F RAID card CABLE, 0x20 Cable/Interconnect FAN_MUX 0x29 Fan multiplexer card PCI_EXPRESS, 0x32 PCI express card on (PEN) FLASH_DIMM, 0x33 Used for SPD devices that matches the silkscreen of the DIMM slot RACK, 0x50 Rack PLATFORM, 0x51 Generic Platform like rack mounted server/appliance DATAPLEX, 0x52 DataPlex OTHER, 0x53 Other unknown etc. PERIPHERAL_MODULE, 0x54 SYSTEM_BOARD, 0x55 System board PROCESSOR_MODULE, 0x56 BACK_PANEL, 0x57 POWER_SYSTEM_BOARD, 0x58 STORAGE_BACKPLANE, 0x59 Drive back plane PROC_BOARD, 0x5A Holds 1 or more processors POWER_DI, 0x5B Power mgt / power distribution board CHASSIS_BACK_PANEL, 0x5C SUB_CHASSIS, 0x5D OTHER_CHASSIS_BOARD, 0x5E DEVICE_MODULE, 0x5F REMOTE_DEVICE, 0x60 Remote mgt communication device EXTERNAL_ENVIRONMENT, 0x61 Such as external temp sensor for outside box temps PROC_MEMORY_MODULE, 0x62 Processors and memory on same module | ||||
| CcomponentMACAddressIndex | 1.3.6.1.4.1.2.3.51.2.22.37.11.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Each component may have one or more MAC address VPD values associated with it, and this index object identifies the particular instance. | ||||
| CcomponentMACAddressName | 1.3.6.1.4.1.2.3.51.2.22.37.11.1.3 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The name of the component as a null terminated string. | ||||
| CcomponentMACAddress | 1.3.6.1.4.1.2.3.51.2.22.37.11.1.4 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The MAC address VPD value for this component and index. The value is a null terminated string. For IOMs which are members of a stack, this field is not applicable and should be disregarded. | ||||
| ScomponentMACAddressTableCacheTimeout | 1.3.6.1.4.1.2.3.51.2.22.37.12 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory The timeout value (in seconds) of the cached data for the table, componentMACAddressTable. This value is static (constant) and cannot be set. | ||||
| TcomponentUniqueIDsTable | 1.3.6.1.4.1.2.3.51.2.22.37.13 | NA | mandatory | |
table · not-accessible · mandatory Table of unique ID information for each component. | ||||
| RcomponentUniqueIDsEntry | 1.3.6.1.4.1.2.3.51.2.22.37.13.1 | NA | mandatory | |
row · not-accessible · mandatory Component unique ID table entry | ||||
| CcomponentUniqueIDsTopologyPath | 1.3.6.1.4.1.2.3.51.2.22.37.13.1.1 | OCTET STRING (SIZE (0..100)) | RO | mandatory |
column · OCTET STRING (SIZE (0..100)) · read-only · mandatory The unique identifier for a component in this table. The chassis and each installed component is represented by a hardware topology tree, where each node in the tree represents a component. The path to a particular component consists of one or more <component>,<instance> pairs, where each successive pair is a child of the previous parent pair. As an example, the root of the tree is the chassis and is represented by the pair 'CHASSIS, 1'. This pair indicates the first instance of the chassis. If a blade is inserted in slot 4 of the chassis, its topology path is 'CHASSIS, 1, BLADE, 4'. With this format, the components in the chassis can be determined along with their relative hierarchy to each other. Note that this TP is preceded by a single octet that specifies the TP length. This is required since this table is indexed with two indices and, therefore, the TP length must be explicitly provided. This component table is indexed by this unique topology path and the numeric designations for the components are: CHASSIS, 0x01 Chassis MM, 0x02 Management Module BLADE, 0x03 Main system board of a blade POWER, 0x04 Power Supply, Power Module, etc COOLING, 0x05 Fan, blower, or other cooling device IO_MODULE, 0x06 Has I/O interface, i.e. - switch or bridge MEDIA, 0x07 Media device PROCESSOR, 0x08 Any processor, processor module, etc STORAGE, 0x09 Any type of storage device EXPANSION, 0x0A Expansion Card (not covered by more specific type) MEMORY, 0x0B Any memory device, module, etc MFRU, 0x0C Managed FRU Device PANEL, 0x0D Any sort of panel device, such as a front panel BLADE_EXPANSION_MODULE, 0x0E Expansion option (BEM) such as PEU, BSE, etc CARD_EXPANSION, 0x0F Expansion card, ie. daughter card CARD_HS_EXPANSION, 0x10 High Speed Expansion card, ie. daughter card INTERPOSER, 0x11 Interposer device CLOCK, 0x12 Clock card MUX, 0x13 Mulitplexer card ADDIN, 0x14 cKVM card & other addin cards STORAGE_MODULE, 0x15 Container of one or more Storage Devices SYS_EXPANSION_CARD, 0x16 Management card BATTERY, 0x17 A single battery BATTERY_MODULE, 0x18 Container of one or more batteries REAR_LED, 0x19 Rear LED card MEMORY_BANK, 0x1A Memory banks AIR_FILTER, 0x1B Filter mechanism (bezel) SERIAL_PORT_MODULE, 0x1C Container of one or more serial ports PARENT, 0x1D Reference to parent for multi-parent support PHY_PORT, 0x1E Physical port IO_EXPANDER, 0x1F RAID card CABLE, 0x20 Cable/Interconnect FAN_MUX 0x29 Fan multiplexer card PCI_EXPRESS, 0x32 PCI express card on (PEN) FLASH_DIMM, 0x33 Used for SPD devices that matches the silkscreen of the DIMM slot RACK, 0x50 Rack PLATFORM, 0x51 Generic Platform like rack mounted server/appliance DATAPLEX, 0x52 DataPlex OTHER, 0x53 Other unknown etc. PERIPHERAL_MODULE, 0x54 SYSTEM_BOARD, 0x55 System board PROCESSOR_MODULE, 0x56 BACK_PANEL, 0x57 POWER_SYSTEM_BOARD, 0x58 STORAGE_BACKPLANE, 0x59 Drive back plane PROC_BOARD, 0x5A Holds 1 or more processors POWER_DI, 0x5B Power mgt / power distribution board CHASSIS_BACK_PANEL, 0x5C SUB_CHASSIS, 0x5D OTHER_CHASSIS_BOARD, 0x5E DEVICE_MODULE, 0x5F REMOTE_DEVICE, 0x60 Remote mgt communication device EXTERNAL_ENVIRONMENT, 0x61 Such as external temp sensor for outside box temps PROC_MEMORY_MODULE, 0x62 Processors and memory on same module | ||||
| CcomponentUniqueIDsIndex | 1.3.6.1.4.1.2.3.51.2.22.37.13.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Each component may have one or more unique ID values associated with it, and this index object identifies the particular instance. | ||||
| CcomponentUniqueIDsName | 1.3.6.1.4.1.2.3.51.2.22.37.13.1.3 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The name of the component as a null terminated string. | ||||
| CcomponentUniqueIDsType | 1.3.6.1.4.1.2.3.51.2.22.37.13.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Type of the unique ID in the object, componentUniqueIDsValue. The type is one of the following: World Wide Name (wwn), Global Unique IDs (guid) or Serial Attach SCSI IDs (sas).
| ||||
| CcomponentUniqueIDsValue | 1.3.6.1.4.1.2.3.51.2.22.37.13.1.5 | OCTET STRING (SIZE (0..255)) | RO | mandatory |
column · OCTET STRING (SIZE (0..255)) · read-only · mandatory The unique ID value for this component and index. The value is a null terminated string. | ||||
| ScomponentUniqueIDsTableCacheTimeout | 1.3.6.1.4.1.2.3.51.2.22.37.14 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory The timeout value (in seconds) of the cached data for the table, componentUniqueIDsTable. This value is static (constant) and cannot be set. | ||||
| TcomponentVoltagesTable | 1.3.6.1.4.1.2.3.51.2.22.37.16 | NA | mandatory | |
table · not-accessible · mandatory Table of component voltage sensor information. | ||||
| RcomponentVoltagesEntry | 1.3.6.1.4.1.2.3.51.2.22.37.16.1 | NA | mandatory | |
row · not-accessible · mandatory Component voltages entry. | ||||
| CcomponentVoltagesTopologyPath | 1.3.6.1.4.1.2.3.51.2.22.37.16.1.1 | OCTET STRING (SIZE (0..100)) | RO | mandatory |
column · OCTET STRING (SIZE (0..100)) · read-only · mandatory The unique identifier for a component in this table. The chassis and each installed component is represented by a hardware topology tree, where each node in the tree represents a component. The path to a particular component consists of one or more <component>,<instance> pairs, where each successive pair is a child of the previous parent pair. As an example, the root of the tree is the chassis and is represented by the pair 'CHASSIS, 1'. This pair indicates the first instance of the chassis. If a blade is inserted in slot 4 of the chassis, its topology path is 'CHASSIS, 1, BLADE, 4'. With this format, the components in the chassis can be determined along with their relative hierarchy to each other. Note that this TP is preceded by a single octet that specifies the TP length. This is required since this table is indexed with two indices and, therefore, the TP length must be explicitly provided. This component table is indexed by this unique topology path and the numeric designations for the components are: CHASSIS, 0x01 Chassis MM, 0x02 Management Module BLADE, 0x03 Main system board of a blade POWER, 0x04 Power Supply, Power Module, etc COOLING, 0x05 Fan, blower, or other cooling device IO_MODULE, 0x06 Has I/O interface, i.e. - switch or bridge MEDIA, 0x07 Media device PROCESSOR, 0x08 Any processor, processor module, etc STORAGE, 0x09 Any type of storage device EXPANSION, 0x0A Expansion Card (not covered by more specific type) MEMORY, 0x0B Any memory device, module, etc MFRU, 0x0C Managed FRU Device PANEL, 0x0D Any sort of panel device, such as a front panel BLADE_EXPANSION_MODULE, 0x0E Expansion option (BEM) such as PEU, BSE, etc CARD_EXPANSION, 0x0F Expansion card, ie. daughter card CARD_HS_EXPANSION, 0x10 High Speed Expansion card, ie. daughter card INTERPOSER, 0x11 Interposer device CLOCK, 0x12 Clock card MUX, 0x13 Mulitplexer card ADDIN, 0x14 cKVM card & other addin cards STORAGE_MODULE, 0x15 Container of one or more Storage Devices SYS_EXPANSION_CARD, 0x16 Management card BATTERY, 0x17 A single battery BATTERY_MODULE, 0x18 Container of one or more batteries REAR_LED, 0x19 Rear LED card MEMORY_BANK, 0x1A Memory banks AIR_FILTER, 0x1B Filter mechanism (bezel) SERIAL_PORT_MODULE, 0x1C Container of one or more serial ports PARENT, 0x1D Reference to parent for multi-parent support PHY_PORT, 0x1E Physical port IO_EXPANDER, 0x1F RAID card CABLE, 0x20 Cable/Interconnect FAN_MUX 0x29 Fan multiplexer card PCI_EXPRESS, 0x32 PCI express card on (PEN) FLASH_DIMM, 0x33 Used for SPD devices that matches the silkscreen of the DIMM slot RACK, 0x50 Rack PLATFORM, 0x51 Generic Platform like rack mounted server/appliance DATAPLEX, 0x52 DataPlex OTHER, 0x53 Other unknown etc. PERIPHERAL_MODULE, 0x54 SYSTEM_BOARD, 0x55 System board PROCESSOR_MODULE, 0x56 BACK_PANEL, 0x57 POWER_SYSTEM_BOARD, 0x58 STORAGE_BACKPLANE, 0x59 Drive back plane PROC_BOARD, 0x5A Holds 1 or more processors POWER_DI, 0x5B Power mgt / power distribution board CHASSIS_BACK_PANEL, 0x5C SUB_CHASSIS, 0x5D OTHER_CHASSIS_BOARD, 0x5E DEVICE_MODULE, 0x5F REMOTE_DEVICE, 0x60 Remote mgt communication device EXTERNAL_ENVIRONMENT, 0x61 Such as external temp sensor for outside box temps PROC_MEMORY_MODULE, 0x62 Processors and memory on same module | ||||
| CcomponentVoltagesSensorIndex | 1.3.6.1.4.1.2.3.51.2.22.37.16.1.2 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory An index for the critical or warning health events for a given component. | ||||
| CcomponentVoltagesComponentName | 1.3.6.1.4.1.2.3.51.2.22.37.16.1.3 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The name of the component as a null terminated string. | ||||
| CcomponentVoltagesSensorLabel | 1.3.6.1.4.1.2.3.51.2.22.37.16.1.4 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The label of the sensor as a null terminated string. | ||||
| CcomponentVoltagesSensorValue | 1.3.6.1.4.1.2.3.51.2.22.37.16.1.5 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The value of the sensor as a null terminated string. | ||||
| CcomponentVoltagesLowWarningThreshold | 1.3.6.1.4.1.2.3.51.2.22.37.16.1.6 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The low warning threshold of the sensor as a null terminated string. | ||||
| CcomponentVoltagesHighWarningThreshold | 1.3.6.1.4.1.2.3.51.2.22.37.16.1.7 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The high warning threshold of the sensor as a null terminated string. | ||||
| ScomponentVoltagesTableCacheTimeout | 1.3.6.1.4.1.2.3.51.2.22.37.17 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory The timeout value (in seconds) of the cached data for the table, componentVoltagesTable. This value is static (constant) and cannot be set. | ||||
| TcomponentTemperaturesTable | 1.3.6.1.4.1.2.3.51.2.22.37.21 | NA | mandatory | |
table · not-accessible · mandatory Table of component temperature sensor information. | ||||
| RcomponentTemperaturesEntry | 1.3.6.1.4.1.2.3.51.2.22.37.21.1 | NA | mandatory | |
row · not-accessible · mandatory Component temperatures entry. | ||||
| CcomponentTemperaturesTopologyPath | 1.3.6.1.4.1.2.3.51.2.22.37.21.1.1 | OCTET STRING (SIZE (0..100)) | RO | mandatory |
column · OCTET STRING (SIZE (0..100)) · read-only · mandatory The unique identifier for a component in this table. The chassis and each installed component is represented by a hardware topology tree, where each node in the tree represents a component. The path to a particular component consists of one or more <component>,<instance> pairs, where each successive pair is a child of the previous parent pair. As an example, the root of the tree is the chassis and is represented by the pair 'CHASSIS, 1'. This pair indicates the first instance of the chassis. If a blade is inserted in slot 4 of the chassis, its topology path is 'CHASSIS, 1, BLADE, 4'. With this format, the components in the chassis can be determined along with their relative hierarchy to each other. Note that this TP is preceded by a single octet that specifies the TP length. This is required since this table is indexed with two indices and, therefore, the TP length must be explicitly provided. This component table is indexed by this unique topology path and the numeric designations for the components are: CHASSIS, 0x01 Chassis MM, 0x02 Management Module BLADE, 0x03 Main system board of a blade POWER, 0x04 Power Supply, Power Module, etc COOLING, 0x05 Fan, blower, or other cooling device IO_MODULE, 0x06 Has I/O interface, i.e. - switch or bridge MEDIA, 0x07 Media device PROCESSOR, 0x08 Any processor, processor module, etc STORAGE, 0x09 Any type of storage device EXPANSION, 0x0A Expansion Card (not covered by more specific type) MEMORY, 0x0B Any memory device, module, etc MFRU, 0x0C Managed FRU Device PANEL, 0x0D Any sort of panel device, such as a front panel BLADE_EXPANSION_MODULE, 0x0E Expansion option (BEM) such as PEU, BSE, etc CARD_EXPANSION, 0x0F Expansion card, ie. daughter card CARD_HS_EXPANSION, 0x10 High Speed Expansion card, ie. daughter card INTERPOSER, 0x11 Interposer device CLOCK, 0x12 Clock card MUX, 0x13 Mulitplexer card ADDIN, 0x14 cKVM card & other addin cards STORAGE_MODULE, 0x15 Container of one or more Storage Devices SYS_EXPANSION_CARD, 0x16 Management card BATTERY, 0x17 A single battery BATTERY_MODULE, 0x18 Container of one or more batteries REAR_LED, 0x19 Rear LED card MEMORY_BANK, 0x1A Memory banks AIR_FILTER, 0x1B Filter mechanism (bezel) SERIAL_PORT_MODULE, 0x1C Container of one or more serial ports PARENT, 0x1D Reference to parent for multi-parent support PHY_PORT, 0x1E Physical port IO_EXPANDER, 0x1F RAID card CABLE, 0x20 Cable/Interconnect FAN_MUX 0x29 Fan multiplexer card PCI_EXPRESS, 0x32 PCI express card on (PEN) FLASH_DIMM, 0x33 Used for SPD devices that matches the silkscreen of the DIMM slot RACK, 0x50 Rack PLATFORM, 0x51 Generic Platform like rack mounted server/appliance DATAPLEX, 0x52 DataPlex OTHER, 0x53 Other unknown etc. PERIPHERAL_MODULE, 0x54 SYSTEM_BOARD, 0x55 System board PROCESSOR_MODULE, 0x56 BACK_PANEL, 0x57 POWER_SYSTEM_BOARD, 0x58 STORAGE_BACKPLANE, 0x59 Drive back plane PROC_BOARD, 0x5A Holds 1 or more processors POWER_DI, 0x5B Power mgt / power distribution board CHASSIS_BACK_PANEL, 0x5C SUB_CHASSIS, 0x5D OTHER_CHASSIS_BOARD, 0x5E DEVICE_MODULE, 0x5F REMOTE_DEVICE, 0x60 Remote mgt communication device EXTERNAL_ENVIRONMENT, 0x61 Such as external temp sensor for outside box temps PROC_MEMORY_MODULE, 0x62 Processors and memory on same module | ||||
| CcomponentTemperaturesSensorIndex | 1.3.6.1.4.1.2.3.51.2.22.37.21.1.2 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory An index for the temperature Sensors for a given component. | ||||
| CcomponentTemperaturesComponentName | 1.3.6.1.4.1.2.3.51.2.22.37.21.1.3 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The name of the component as a null terminated string. | ||||
| CcomponentTemperaturesSensorLabel | 1.3.6.1.4.1.2.3.51.2.22.37.21.1.4 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The label of the sensor as a null terminated string. | ||||
| CcomponentTemperaturesSensorValue | 1.3.6.1.4.1.2.3.51.2.22.37.21.1.5 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The value of the sensor as a null terminated string. | ||||
| CcomponentTemperaturesWarningThreshold | 1.3.6.1.4.1.2.3.51.2.22.37.21.1.6 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The warning threshold of the sensor as a null terminated string. | ||||
| CcomponentTemperaturesShutdownThreshold | 1.3.6.1.4.1.2.3.51.2.22.37.21.1.7 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The Shutdown threshold of the sensor as a null terminated string. | ||||
| CcomponentTemperaturesWarningResetThreshold | 1.3.6.1.4.1.2.3.51.2.22.37.21.1.8 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The Warning Reset threshold of the sensor as a null terminated string. | ||||
| ScomponentTemperaturesTableCacheTimeout | 1.3.6.1.4.1.2.3.51.2.22.37.22 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory The timeout value (in seconds) of the cached data for the table, componentTemperaturesTable. This value is static (constant) and cannot be set. | ||||
| TcomponentIOCompatibilityTable | 1.3.6.1.4.1.2.3.51.2.22.37.26 | NA | mandatory | |
table · not-accessible · mandatory Table of component IO Compatibility information. | ||||
| RcomponentIOCompatibilityEntry | 1.3.6.1.4.1.2.3.51.2.22.37.26.1 | NA | mandatory | |
row · not-accessible · mandatory Component IO compatibility entry. | ||||
| CcomponentIOCompatibilityTopologyPath | 1.3.6.1.4.1.2.3.51.2.22.37.26.1.1 | OCTET STRING (SIZE (0..100)) | RO | mandatory |
column · OCTET STRING (SIZE (0..100)) · read-only · mandatory The unique identifier for a component in this table. The chassis and each installed component is represented by a hardware topology tree, where each node in the tree represents a component. The path to a particular component consists of one or more <component>,<instance> pairs, where each successive pair is a child of the previous parent pair. As an example, the root of the tree is the chassis and is represented by the pair 'CHASSIS, 1'. This pair indicates the first instance of the chassis. If a blade is inserted in slot 4 of the chassis, its topology path is 'CHASSIS, 1, BLADE, 4'. With this format, the components in the chassis can be determined along with their relative hierarchy to each other. Note that this TP is preceded by a single octet that specifies the TP length. This is required since this table is indexed with two indices and, therefore, the TP length must be explicitly provided. This component table is indexed by this unique topology path and the numeric designations for the components are: CHASSIS, 0x01 Chassis MM, 0x02 Management Module BLADE, 0x03 Main system board of a blade POWER, 0x04 Power Supply, Power Module, etc COOLING, 0x05 Fan, blower, or other cooling device IO_MODULE, 0x06 Has I/O interface, i.e. - switch or bridge MEDIA, 0x07 Media device PROCESSOR, 0x08 Any processor, processor module, etc STORAGE, 0x09 Any type of storage device EXPANSION, 0x0A Expansion Card (not covered by more specific type) MEMORY, 0x0B Any memory device, module, etc MFRU, 0x0C Managed FRU Device PANEL, 0x0D Any sort of panel device, such as a front panel BLADE_EXPANSION_MODULE, 0x0E Expansion option (BEM) such as PEU, BSE, etc CARD_EXPANSION, 0x0F Expansion card, ie. daughter card CARD_HS_EXPANSION, 0x10 High Speed Expansion card, ie. daughter card INTERPOSER, 0x11 Interposer device CLOCK, 0x12 Clock card MUX, 0x13 Mulitplexer card ADDIN, 0x14 cKVM card & other addin cards STORAGE_MODULE, 0x15 Container of one or more Storage Devices SYS_EXPANSION_CARD, 0x16 Management card BATTERY, 0x17 A single battery BATTERY_MODULE, 0x18 Container of one or more batteries REAR_LED, 0x19 Rear LED card MEMORY_BANK, 0x1A Memory banks AIR_FILTER, 0x1B Filter mechanism (bezel) SERIAL_PORT_MODULE, 0x1C Container of one or more serial ports PARENT, 0x1D Reference to parent for multi-parent support PHY_PORT, 0x1E Physical port IO_EXPANDER, 0x1F RAID card CABLE, 0x20 Cable/Interconnect FAN_MUX 0x29 Fan multiplexer card PCI_EXPRESS, 0x32 PCI express card on (PEN) FLASH_DIMM, 0x33 Used for SPD devices that matches the silkscreen of the DIMM slot RACK, 0x50 Rack PLATFORM, 0x51 Generic Platform like rack mounted server/appliance DATAPLEX, 0x52 DataPlex OTHER, 0x53 Other unknown etc. PERIPHERAL_MODULE, 0x54 SYSTEM_BOARD, 0x55 System board PROCESSOR_MODULE, 0x56 BACK_PANEL, 0x57 POWER_SYSTEM_BOARD, 0x58 STORAGE_BACKPLANE, 0x59 Drive back plane PROC_BOARD, 0x5A Holds 1 or more processors POWER_DI, 0x5B Power mgt / power distribution board CHASSIS_BACK_PANEL, 0x5C SUB_CHASSIS, 0x5D OTHER_CHASSIS_BOARD, 0x5E DEVICE_MODULE, 0x5F REMOTE_DEVICE, 0x60 Remote mgt communication device EXTERNAL_ENVIRONMENT, 0x61 Such as external temp sensor for outside box temps PROC_MEMORY_MODULE, 0x62 Processors and memory on same module | ||||
| CcomponentIOCompatibilityIOMBay | 1.3.6.1.4.1.2.3.51.2.22.37.26.1.2 | INTEGER (0..255) | RO | mandatory |
column · INTEGER (0..255) · read-only · mandatory An index for the IO Compatibility modules for a given component. | ||||
| CcomponentIOCompatibilityComponentName | 1.3.6.1.4.1.2.3.51.2.22.37.26.1.3 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The name of the component as a null terminated string. | ||||
| CcomponentIOCompatibilityIOMPower | 1.3.6.1.4.1.2.3.51.2.22.37.26.1.4 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The power state of the module specified in componentIOCompatibilityIOMBay. n/a if module not installed. | ||||
| CcomponentIOCompatibilityIOMFabricType | 1.3.6.1.4.1.2.3.51.2.22.37.26.1.5 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The fabric type of the module specified in componentIOCompatibilityIOMBay. | ||||
| CcomponentIOCompatibilityFabricOnComponent | 1.3.6.1.4.1.2.3.51.2.22.37.26.1.6 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The fabric type for this channel on the original component (may be onboard fabric or an expansion card). | ||||
| CcomponentIOCompatibilityStatus | 1.3.6.1.4.1.2.3.51.2.22.37.26.1.7 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The compatibility status between the component and the module specified
in componentIOCompatibilityIOMBay.
The possible values are:
OK: No compatibility issues
No IOM: There is no module on the other side of the wire for this channel on the component.
n/a: (Not applicable) The module specified in componentIOCompatibilityIOMBay is a bridge,
so the component port cannot connect to it.
Attention: The module specified in componentIOCompatibilityIOMBay has a communication error.
Mismatch: Indicates one of the following cases:
Fabric types are incompatible
Module specified in componentIOCompatibilityIOMBay is of unknown type
Unknown fabric type on the component | ||||
| ScomponentIOCompatibilityTableCacheTimeout | 1.3.6.1.4.1.2.3.51.2.22.37.27 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory The timeout value (in seconds) of the cached data for the table, componentIOCompatibilityTable. This value is static (constant) and cannot be set. | ||||
| TnodeConnectivityTable | 1.3.6.1.4.1.2.3.51.2.22.37.31 | NA | mandatory | |
table · not-accessible · mandatory Table of node connectivity information. This table provides information related to the node communication status. | ||||
| RnodeConnectivityEntry | 1.3.6.1.4.1.2.3.51.2.22.37.31.1 | NA | mandatory | |
| CnodeConnectivityIndex | 1.3.6.1.4.1.2.3.51.2.22.37.31.1.1 | INTEGER (0..128) | RO | mandatory |
column · INTEGER (0..128) · read-only · mandatory Node Connectivity table index. | ||||
| CnodeConnectivityName | 1.3.6.1.4.1.2.3.51.2.22.37.31.1.2 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The name of the node as a null terminated string. | ||||
| CnodeConnectivityStatus | 1.3.6.1.4.1.2.3.51.2.22.37.31.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates the communication status of the node.
| ||||
| NcomponentServiceReset | 1.3.6.1.4.1.2.3.51.2.22.38 | |||
| TcomponentServiceResetTable | 1.3.6.1.4.1.2.3.51.2.22.38.1 | NA | mandatory | |
table · not-accessible · mandatory A table providing aux power status and the ability to perform a virtual reseat or hard restart of a component. | ||||
| RcomponentServiceResetEntry | 1.3.6.1.4.1.2.3.51.2.22.38.1.1 | NA | mandatory | |
row · not-accessible · mandatory Component module power service reset entry | ||||
| CcomponentServiceResetTopologyPath | 1.3.6.1.4.1.2.3.51.2.22.38.1.1.1 | OCTET STRING (SIZE (0..100)) | RO | mandatory |
column · OCTET STRING (SIZE (0..100)) · read-only · mandatory The unique identifier for a row in this table. The chassis and each installed component is represented by a hardware topology tree, where each node in the tree represents a component. The path to a particular component consists of one or more <component>,<instance> pairs, where each successive pair is a child of the previous parent pair. As an example, the root of the tree is the chassis and is represented by the pair 'CHASSIS, 1'. This pair indicates the first instance of the chassis. If a blade is inserted in slot 4 of the chassis, its topology path is 'CHASSIS, 1, BLADE, 4'. With this format, the components in the chassis can be determined along with their relative hierarchy to each other. This component table is indexed by this unique topology path and the numeric designations for the components are: CHASSIS, 0x01 Chassis MM, 0x02 Management Module BLADE, 0x03 Main system board of a blade POWER, 0x04 Power Supply, Power Module, etc COOLING, 0x05 Fan, blower, or other cooling device IO_MODULE, 0x06 Has I/O interface, i.e. - switch or bridge MEDIA, 0x07 Media device PROCESSOR, 0x08 Any processor, processor module, etc STORAGE, 0x09 Any type of storage device EXPANSION, 0x0A Expansion Card (not covered by more specific type) MEMORY, 0x0B Any memory device, module, etc MFRU, 0x0C Managed FRU Device PANEL, 0x0D Any sort of panel device, such as a front panel BLADE_EXPANSION_MODULE, 0x0E Expansion option (BEM) such as PEU, BSE, etc CARD_EXPANSION, 0x0F Expansion card, ie. daughter card CARD_HS_EXPANSION, 0x10 High Speed Expansion card, ie. daughter card INTERPOSER, 0x11 Interposer device CLOCK, 0x12 Clock card MUX, 0x13 Mulitplexer card ADDIN, 0x14 cKVM card & other addin cards STORAGE_MODULE, 0x15 Container of one or more Storage Devices SYS_EXPANSION_CARD, 0x16 Management card BATTERY, 0x17 A single battery BATTERY_MODULE, 0x18 Container of one or more batteries MEDIA_MODULE, 0x19 Container of one or more media devices MEMORY_BANK, 0x1A Memory banks AIR_FILTER, 0x1B Filter mechanism (bezel) SERIAL_PORT_MODULE, 0x1C Container of one or more serial ports PARENT, 0x1D Reference to parent for multi-parent support PHY_PORT, 0x1E Physical port IO_EXPANDER, 0x1F RAID card CABLE, 0x20 Cable/Interconnect FAN_MUX, 0x29 Fan multiplexer card PCI_EXPRESS, 0x32 PCI express card on (PEN) FLASH_DIMM, 0x33 Used for SPD devices that matches the silkscreen of the DIMM slot RACK, 0x50 Rack PLATFORM, 0x51 Generic Platform like rack mounted server/appliance DATAPLEX, 0x52 DataPlex OTHER, 0x53 Other unknown etc. PERIPHERAL_MODULE, 0x54 SYSTEM_BOARD, 0x55 System board PROCESSOR_MODULE, 0x56 BACK_PANEL, 0x57 POWER_SYSTEM_BOARD, 0x58 STORAGE_BACKPLANE, 0x59 Drive back plane PROC_BOARD, 0x5A Holds 1 or more processors POWER_DI, 0x5B Power mgt / power distribution board CHASSIS_BACK_PANEL, 0x5C SUB_CHASSIS, 0x5D OTHER_CHASSIS_BOARD, 0x5E DEVICE_MODULE, 0x5F REMOTE_DEVICE, 0x60 Remote mgt communication device EXTERNAL_ENVIRONMENT, 0x61 Such as external temp sensor for outside box temps PROC_MEMORY_MODULE, 0x62 Processors and memory on same module | ||||
| CcomponentServiceResetName | 1.3.6.1.4.1.2.3.51.2.22.38.1.1.2 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory A short text string describing the particular component. For the MM and blades, this name will be the configured name or its serial number if no user configured name is available. For all other components, this object will provide text to identify the component. | ||||
| CcomponentServiceResetStatus | 1.3.6.1.4.1.2.3.51.2.22.38.1.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Status of the aux power. A value of auxPowerOff(0) indicates that the componant aux power is off. A value of auxPowerOn(1) indicates that the componant aux power is on.
| ||||
| CcomponentServiceResetCmd | 1.3.6.1.4.1.2.3.51.2.22.38.1.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory NOTE: Do not perform this service reset operation on a node that is currently in a maintenance mode state. See componentStatusHealthState in componentSystemStatusTable for maintMode(12) value. To reset the auxiliary power on a component, set this object to resetVirtualReseatOperation(1). This will toggle the auxiliary power and simulate a physical removal and insertion. During the operation, auxiliary power is removed from the component and is then restored. For nodes, the power state will remain off and the user will need to manually power on the node. To perform a hard restart on the component, set this object to resetHardRestartOperation(2). This will toggle the reset line to the processor causing it to re-initialize. This object is intended to be write-only. The component will experience a temporary loss of communication and the power state will change. Prior to executing this action, perform any operations needed to protect user data. Reading this object will always return the value of noOperation(0).
| ||||
| ScomponentServiceResetTableCacheTimeout | 1.3.6.1.4.1.2.3.51.2.22.38.2 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory The timeout value (in seconds) of the cached data for the table, componentServiceResetTable. This value is static (constant) and cannot be set. | ||||
| NcomponentLEDs | 1.3.6.1.4.1.2.3.51.2.22.39 | |||
| TcomponentLEDsTable | 1.3.6.1.4.1.2.3.51.2.22.39.1 | NA | mandatory | |
table · not-accessible · mandatory Table of component LED information. NOTE: Querying objects in this table may take significantly longer than normal, so it is recommended that the query timeout be set to a large value. On a fully populated chassis, the timeout should be set to 120 seconds or more. | ||||
| RcomponentLEDsEntry | 1.3.6.1.4.1.2.3.51.2.22.39.1.1 | NA | mandatory | |
| CledComponentTopologyPath | 1.3.6.1.4.1.2.3.51.2.22.39.1.1.1 | OCTET STRING (SIZE (0..100)) | RO | mandatory |
column · OCTET STRING (SIZE (0..100)) · read-only · mandatory The unique identifier for a component in this table. The chassis and each installed component is represented by a hardware topology tree, where each node in the tree represents a component. The path to a particular component consists of one or more <component>,<instance> pairs, where each successive pair is a child of the previous parent pair. As an example, the root of the tree is the chassis and is represented by the pair 'CHASSIS, 1'. This pair indicates the first instance of the chassis. If a blade is inserted in slot 4 of the chassis, its topology path is 'CHASSIS, 1, BLADE, 4'. With this format, the components in the chassis can be determined along with their relative hierarchy to each other. This component table is indexed by this unique topology path and the numeric designations for the components are: CHASSIS, 0x01 Chassis MM, 0x02 Management Module BLADE, 0x03 Main system board of a blade POWER, 0x04 Power Supply, Power Module, etc COOLING, 0x05 Fan, blower, or other cooling device IO_MODULE, 0x06 Has I/O interface, i.e. - switch or bridge MEDIA, 0x07 Media device PROCESSOR, 0x08 Any processor, processor module, etc STORAGE, 0x09 Any type of storage device EXPANSION, 0x0A Expansion Card (not covered by more specific type) MEMORY, 0x0B Any memory device, module, etc MFRU, 0x0C Managed FRU Device PANEL, 0x0D Any sort of panel device, such as a front panel BLADE_EXPANSION_MODULE, 0x0E Expansion option (BEM) such as PEU, BSE, etc CARD_EXPANSION, 0x0F Expansion card, ie. daughter card CARD_HS_EXPANSION, 0x10 High Speed Expansion card, ie. daughter card INTERPOSER, 0x11 Interposer device CLOCK, 0x12 Clock card MUX, 0x13 Mulitplexer card ADDIN, 0x14 cKVM card & other addin cards STORAGE_MODULE, 0x15 Container of one or more Storage Devices SYS_EXPANSION_CARD, 0x16 Management card BATTERY, 0x17 A single battery BATTERY_MODULE, 0x18 Container of one or more batteries REAR_LED, 0x19 Rear LED card MEMORY_BANK, 0x1A Memory banks AIR_FILTER, 0x1B Filter mechanism (bezel) SERIAL_PORT_MODULE, 0x1C Container of one or more serial ports PARENT, 0x1D Reference to parent for multi-parent support PHY_PORT, 0x1E Physical port IO_EXPANDER, 0x1F RAID card CABLE, 0x20 Cable/Interconnect FAN_MUX 0x29 Fan multiplexer card PCI_EXPRESS, 0x32 PCI express card on (PEN) FLASH_DIMM, 0x33 Used for SPD devices that matches the silkscreen of the DIMM slot RACK, 0x50 Rack PLATFORM, 0x51 Generic Platform like rack mounted server/appliance DATAPLEX, 0x52 DataPlex OTHER, 0x53 Other unknown etc. PERIPHERAL_MODULE, 0x54 SYSTEM_BOARD, 0x55 System board PROCESSOR_MODULE, 0x56 BACK_PANEL, 0x57 POWER_SYSTEM_BOARD, 0x58 STORAGE_BACKPLANE, 0x59 Drive back plane PROC_BOARD, 0x5A Holds 1 or more processors POWER_DI, 0x5B Power mgt / power distribution board CHASSIS_BACK_PANEL, 0x5C SUB_CHASSIS, 0x5D OTHER_CHASSIS_BOARD, 0x5E DEVICE_MODULE, 0x5F REMOTE_DEVICE, 0x60 Remote mgt communication device EXTERNAL_ENVIRONMENT, 0x61 Such as external temp sensor for outside box temps PROC_MEMORY_MODULE, 0x62 Processors and memory on same module | ||||
| CledComponentName | 1.3.6.1.4.1.2.3.51.2.22.39.1.1.2 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The name of the component as a null terminated string. | ||||
| CledComponentFault | 1.3.6.1.4.1.2.3.51.2.22.39.1.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether the component fault LED is on or off.
| ||||
| CledComponentCheckLog | 1.3.6.1.4.1.2.3.51.2.22.39.1.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Indicates whether the component check log information LED is on or off. For Write access, the LED can be turned off only.
| ||||
| CledComponentIdentity | 1.3.6.1.4.1.2.3.51.2.22.39.1.1.5 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Indicates whether the component identify LED is on, off, or blinking.
| ||||
| ScomponentLEDsTableCacheTimeout | 1.3.6.1.4.1.2.3.51.2.22.39.2 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory The timeout value (in seconds) of the cached data for the table, componentLEDsTable. This value is static (constant) and cannot be set. | ||||
| TcomponentLEDsDetailsTable | 1.3.6.1.4.1.2.3.51.2.22.39.9 | NA | mandatory | |
table · not-accessible · mandatory Table of LED info for each component. | ||||
| RcomponentLEDsDetailsEntry | 1.3.6.1.4.1.2.3.51.2.22.39.9.1 | NA | mandatory | |
row · not-accessible · mandatory Component LED info table entry | ||||
| CcomponentLEDsDetailsTopologyPath | 1.3.6.1.4.1.2.3.51.2.22.39.9.1.1 | OCTET STRING (SIZE (0..100)) | RO | mandatory |
column · OCTET STRING (SIZE (0..100)) · read-only · mandatory The unique identifier for a component in this table. The chassis and each installed component is represented by a hardware topology tree, where each node in the tree represents a component. The path to a particular component consists of one or more <component>,<instance> pairs, where each successive pair is a child of the previous parent pair. As an example, the root of the tree is the chassis and is represented by the pair 'CHASSIS, 1'. This pair indicates the first instance of the chassis. If a blade is inserted in slot 4 of the chassis, its topology path is 'CHASSIS, 1, BLADE, 4'. With this format, the components in the chassis can be determined along with their relative hierarchy to each other. Note that this TP is preceded by a single octet that specifies the TP length. This is required since this table is indexed with two indices and, therefore, the TP length must be explicitly provided. This component table is indexed by this unique topology path and the numeric designations for the components are: CHASSIS, 0x01 Chassis MM, 0x02 Management Module BLADE, 0x03 Main system board of a blade POWER, 0x04 Power Supply, Power Module, etc COOLING, 0x05 Fan, blower, or other cooling device IO_MODULE, 0x06 Has I/O interface, i.e. - switch or bridge MEDIA, 0x07 Media device PROCESSOR, 0x08 Any processor, processor module, etc STORAGE, 0x09 Any type of storage device EXPANSION, 0x0A Expansion Card (not covered by more specific type) MEMORY, 0x0B Any memory device, module, etc MFRU, 0x0C Managed FRU Device PANEL, 0x0D Any sort of panel device, such as a front panel BLADE_EXPANSION_MODULE, 0x0E Expansion option (BEM) such as PEU, BSE, etc CARD_EXPANSION, 0x0F Expansion card, ie. daughter card CARD_HS_EXPANSION, 0x10 High Speed Expansion card, ie. daughter card INTERPOSER, 0x11 Interposer device CLOCK, 0x12 Clock card MUX, 0x13 Mulitplexer card ADDIN, 0x14 cKVM card & other addin cards STORAGE_MODULE, 0x15 Container of one or more Storage Devices SYS_EXPANSION_CARD, 0x16 Management card BATTERY, 0x17 A single battery BATTERY_MODULE, 0x18 Container of one or more batteries REAR_LED, 0x19 Rear LED card MEMORY_BANK, 0x1A Memory banks AIR_FILTER, 0x1B Filter mechanism (bezel) SERIAL_PORT_MODULE, 0x1C Container of one or more serial ports PARENT, 0x1D Reference to parent for multi-parent support PHY_PORT, 0x1E Physical port IO_EXPANDER, 0x1F RAID card CABLE, 0x20 Cable/Interconnect FAN_MUX 0x29 Fan multiplexer card PCI_EXPRESS, 0x32 PCI express card on (PEN) FLASH_DIMM, 0x33 Used for SPD devices that matches the silkscreen of the DIMM slot RACK, 0x50 Rack PLATFORM, 0x51 Generic Platform like rack mounted server/appliance DATAPLEX, 0x52 DataPlex OTHER, 0x53 Other unknown etc. PERIPHERAL_MODULE, 0x54 SYSTEM_BOARD, 0x55 System board PROCESSOR_MODULE, 0x56 BACK_PANEL, 0x57 POWER_SYSTEM_BOARD, 0x58 STORAGE_BACKPLANE, 0x59 Drive back plane PROC_BOARD, 0x5A Holds 1 or more processors POWER_DI, 0x5B Power mgt / power distribution board CHASSIS_BACK_PANEL, 0x5C SUB_CHASSIS, 0x5D OTHER_CHASSIS_BOARD, 0x5E DEVICE_MODULE, 0x5F REMOTE_DEVICE, 0x60 Remote mgt communication device EXTERNAL_ENVIRONMENT, 0x61 Such as external temp sensor for outside box temps PROC_MEMORY_MODULE, 0x62 Processors and memory on same module | ||||
| CcomponentLEDsDetailsIndex | 1.3.6.1.4.1.2.3.51.2.22.39.9.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Each component may have one or more LEDs and data associated with it, and this index object identifies the particular instance. | ||||
| CcomponentLEDsDetailsComponentType | 1.3.6.1.4.1.2.3.51.2.22.39.9.1.3 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The type of the component/subcomponent grouping for this LED. | ||||
| CcomponentLEDsDetailsLabel | 1.3.6.1.4.1.2.3.51.2.22.39.9.1.4 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The text description of the LED. | ||||
| CcomponentLEDsDetailsState | 1.3.6.1.4.1.2.3.51.2.22.39.9.1.5 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current state of the LED.
| ||||
| CcomponentLEDsDetailsLocation | 1.3.6.1.4.1.2.3.51.2.22.39.9.1.6 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The physical location of this LED on the hardware. | ||||
| ScomponentLEDsDetailsTableCacheTimeout | 1.3.6.1.4.1.2.3.51.2.22.39.10 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory The timeout value (in seconds) of the cached data for the table, componentLEDsDetailsTable. This value is static (constant) and cannot be set. | ||||
| NbackupRestore | 1.3.6.1.4.1.2.3.51.2.22.42 | |||
| SbackupRestoreAction | 1.3.6.1.4.1.2.3.51.2.22.42.1 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Starts the backup or restore operation. It is intended to be write-only. NOTE: This function is only available for SNMPv3.
| ||||
| SbackupRestoreStatus | 1.3.6.1.4.1.2.3.51.2.22.42.2 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory Get the status of the last backup/restore action which was initiated through SNMP. NOTE: This function is only available for SNMPv3.
| ||||
| SbackupRestoreMessage | 1.3.6.1.4.1.2.3.51.2.22.42.3 | OCTET STRING | RO | mandatory |
scalar · OCTET STRING · read-only · mandatory Get the status message of the last backup/restore action which was
initiated through SNMP.
NOTE: This function is only available for SNMPv3. | ||||
| SbackupRestoreURI | 1.3.6.1.4.1.2.3.51.2.22.42.4 | OCTET STRING (SIZE (0..254)) | RW | mandatory |
scalar · OCTET STRING (SIZE (0..254)) · read-write · mandatory Contains the fully qualified remote location of the file. A fully qualified remote location contains a supported protocol followed by a colon and two slashes (//), userid and password separated by a colon for login authentication, an @ sign, followed by the hostname or IP address of the server where the packet file resides, followed by an optional port number to the hostname, and the full pathname to the file. Note that if the port number is specified, it must be separated with the hostname (or IP address) by a colon. The MM currently supports the following protocols: TFTP, FTP, HTTP and HTTPS. The complete format of a fully qualified remote location is: <protocol>://<userid:password>@<hostname:port>/<pathname> An example of a fully qualified remote location can be: ftp://USERID:[email protected]:30045/tmp/cmd.bkp where the ftp protocol will be used for transferring the file in this location, username is USERID, password is PASSW0RD, host IP address is 192.168.0.2, port number is 30045, and the full pathname for the packet file is /tmp/cmd.bkp. Some protocols do not need the username, password, and the port number, so the minimum requirement for a fully qualified location can be:<protocol>://<hostname>/<pathname>. Note:When using SFTP, only an RSA fingerprint is supported. An example of a qualified location can be: <protocol>://[<user>[:password][;fingerprint=<host>]@]<host> [:<port>]/<path>/<to>/<file> NOTE: This function is only available for SNMPv3. | ||||
| SbackupRestorePassword | 1.3.6.1.4.1.2.3.51.2.22.42.5 | OCTET STRING (SIZE (0..63)) | RW | mandatory |
scalar · OCTET STRING (SIZE (0..63)) · read-write · mandatory Password used for the encryption/decryption of the sensitive data in the backup file. It is intended to be write-only. NOTE: This function is only available for SNMPv3. | ||||
| SbackupRestoreLogURI | 1.3.6.1.4.1.2.3.51.2.22.42.6 | OCTET STRING (SIZE (0..254)) | RW | mandatory |
scalar · OCTET STRING (SIZE (0..254)) · read-write · mandatory Indicates the URI address where the log file will be put. It will be used only if the backupRestoreLogPush will be set on push. Contains the fully qualified remote location of the file. A fully qualified remote location contains a supported protocol followed by a colon and two slashes (//), userid and password separated by a colon for login authentication, an @ sign, followed by the hostname or IP address of the server where the packet file will reside, followed by an optional port number to the hostname, and the full pathname to the file. Note that if the port number is specified, it must be separated with the hostname (or IP address) by a colon. The MM currently supports the following protocols: TFTP, FTP, HTTP and HTTPS. The complete format of a fully qualified remote location is: <protocol>://<userid:password>@<hostname:port>/<pathname> An example of a fully qualified remote location can be: ftp://USERID:[email protected]:30045/tmp/restore.log where the ftp protocol will be used for transferring the file in this location, username is USERID, password is PASSW0RD, host IP address is 192.168.0.2, port number is 30045, and the full pathname for the packet file is /tmp/restore.log. Some protocols do not need the username, password, and the port number, so the minimum requirement for a fully qualified location can be:<protocol>://<hostname>/<pathname>. Note: When using SFTP, only an RSA fingerprint is supported. An example of a qualified location can be: <protocol>://[<user>[:password][;fingerprint=<host>]@]<host> [:<port>]/<path>/<to>/<file> NOTE: This function is available only for SNMPv3. | ||||
| SbackupRestoreLogPush | 1.3.6.1.4.1.2.3.51.2.22.42.7 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Causes the restore operation to push the log to the URI address. NOTE: This can be used when restoring without restarting. NOTE: This function is only available for SNMPv3.
| ||||
| Nservice | 1.3.6.1.4.1.2.3.51.2.23 | |||
| NbladeServiceData | 1.3.6.1.4.1.2.3.51.2.23.3 | |||
| TbladeServiceDataTable | 1.3.6.1.4.1.2.3.51.2.23.3.1 | NA | mandatory | |
table · not-accessible · mandatory Table of blade service data information. | ||||
| RbladeServiceDataEntry | 1.3.6.1.4.1.2.3.51.2.23.3.1.1 | NA | mandatory | |
| CserviceDataIndex | 1.3.6.1.4.1.2.3.51.2.23.3.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Blade service date index. | ||||
| CserviceDataBladeId | 1.3.6.1.4.1.2.3.51.2.23.3.1.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The numeric blade ID.
| ||||
| CserviceDataBladeExists | 1.3.6.1.4.1.2.3.51.2.23.3.1.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether the blade specified exists or not.
| ||||
| CserviceDataBladePowerState | 1.3.6.1.4.1.2.3.51.2.23.3.1.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates whether the blade specified is powered on or not. If the MM is experiencing a communication problem with the blade, the state may be returned as unknown(255)
| ||||
| CserviceDataBladeName | 1.3.6.1.4.1.2.3.51.2.23.3.1.1.5 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The name of the blade as a string. | ||||
| CserviceDataDumpInitiate | 1.3.6.1.4.1.2.3.51.2.23.3.1.1.7 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Initiates a type of dump collection to be initiated for the blade. NOTE: Not all blades support this, please check serviceDataDumpCapabilityMask OID to see if the action is supported on this blade. When the dump file is created, the node transfers it to the /tftproot/service directory on the CMM. Only one file can be moved to this directory at a time, so please use the fileManagement MIB information to check if the file has been completed. NOTE: Value returned for the GET command is meaningless for this MIB object.
| ||||
| CserviceDataDumpRetrieve | 1.3.6.1.4.1.2.3.51.2.23.3.1.1.8 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Retrieve a type of service data file from blade to MM. NOTE: This OID only is valid for the last four bit mask designations listed in the serviceDataDumpCapabilityMask OID. The dump file is transfered to the /tftproot/service directory on the CMM. Only one file can be moved to this directory at a time, so please use the fileManagement MIB information to check if the file has been completed. NOTE: Value returned for the GET command is meaningless for this MIB object.
| ||||
| CserviceDataDumpCapabilityMask | 1.3.6.1.4.1.2.3.51.2.23.3.1.1.9 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Indicates whether the blade has the capability to trigger service data and if so, which operations are supported and whether the file can be transferred to the MM from the blade. The values and meanings are as follows: 0000 0000 means this blade does not support any at all. 0000 0001 means this blade supports 'processor' type and the file remains on the blade. 0000 0010 means this blade supports 'platform' type and the file remains on the blade 0000 0100 means this blade supports 'partition' type and the file remians on the blade 0000 1000 means this blade supports 'processor' type and the file can be transferred to the MM. 0001 0000 means this blade supports 'platform' type and the file can be transferred to the MM. 0010 0000 means this blade supports 'partition' type and the file can be transferred to the MM 0100 0000 means this blade supports 'serviceData' type and the file can be transferred to the MM For example, the returned value of 01111000 means this blade supports 'processor','platform', 'partition' and 'serviceData' types, and the file can be transferred to the MM | ||||
| CserviceDataDumpInProgress | 1.3.6.1.4.1.2.3.51.2.23.3.1.1.10 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory An indicator as to whether a blade dump is in progress for the specified blade. This object ONLY applies to dumps that can be triggered by the MM and where the dump file is transferred to the MM filesystem upon completion. See the serviceDataDumpCapabilityMask object for support levels. The flag that this MIB object represents will be set on when the IPMI command is sent to the blade indicating 'init dump' and will be cleared upon receiving the valid dump file from the blade or the creation of the text file indicating the problem encountered. If it cannot be determined if the dump is in progress, the unknown(255) value is returned.
| ||||
| NserviceAdvisor | 1.3.6.1.4.1.2.3.51.2.23.4 | |||
| NautoCallHomeSetup | 1.3.6.1.4.1.2.3.51.2.23.4.1 | |||
| SacceptLicenseAgreement | 1.3.6.1.4.1.2.3.51.2.23.4.1.1 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Accept Terms and Conditions of MM Service Advisor. The user will have to accept the terms and conditions before Service Advisor can send diagnostic data to IBM support personnel. If MM configuration is reset to defaults, the user will have to accept the terms and conditions again before they can enable Service Advisor. A GET of this object may return disabled(0) or enabled(1), depending upon the current state. However, only enabled(1) is accepted on a SET in order to accept the license agreement. A SET of disabled(0) will return noSuchValue and is not allowed.
| ||||
| SserviceAdvisorEnable | 1.3.6.1.4.1.2.3.51.2.23.4.1.2 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Disable/Enable IBM Support. The User Agreement must be accepted and the contact information must be set before the IBM Support function of Service Advisor can be enabled.
| ||||
| NserviceSupportCenter | 1.3.6.1.4.1.2.3.51.2.23.4.2 | |||
| SibmSupportCenter | 1.3.6.1.4.1.2.3.51.2.23.4.2.1 | OCTET STRING | RW | mandatory |
scalar · OCTET STRING · read-write · mandatory The country code for the IBM Support Center. 2 character ISO country code. | ||||
| NcontactInformation | 1.3.6.1.4.1.2.3.51.2.23.4.3 | |||
| ScompanyName | 1.3.6.1.4.1.2.3.51.2.23.4.3.1 | OCTET STRING | RW | mandatory |
scalar · OCTET STRING · read-write · mandatory The organization/company name of the contact person. 1-30 characters. | ||||
| ScontactName | 1.3.6.1.4.1.2.3.51.2.23.4.3.2 | OCTET STRING | RW | mandatory |
scalar · OCTET STRING · read-write · mandatory The name of the contact person.1-30 characters. | ||||
| SphoneNumber | 1.3.6.1.4.1.2.3.51.2.23.4.3.3 | OCTET STRING | RW | mandatory |
scalar · OCTET STRING · read-write · mandatory The phone of the contact person. 5-30 characters. | ||||
| SemailAddress | 1.3.6.1.4.1.2.3.51.2.23.4.3.4 | OCTET STRING | RW | mandatory |
scalar · OCTET STRING · read-write · mandatory The email of the contact person. It must contain '@' and dot '.' in form userid@hostname (130 characters maximum). The userid can be alphanumeric characters, '.', '-', or '_' but must begin and end with alphanumeric characters. The hostname can be alphanumeric characters, '.', '-', or '_'. It must contain at least two domain items. Every domain item should begin and end with alphanumeric character, and the last domain item should be 2-20 alphabetic characters. | ||||
| Saddress | 1.3.6.1.4.1.2.3.51.2.23.4.3.5 | OCTET STRING | RW | mandatory |
scalar · OCTET STRING · read-write · mandatory The address of the machine location. The information in this field should be of sufficient detail to allow someone to quickly find the chassis when necessary. 1-30 characters. | ||||
| Scity | 1.3.6.1.4.1.2.3.51.2.23.4.3.6 | OCTET STRING | RW | mandatory |
scalar · OCTET STRING · read-write · mandatory The city of the machine location. 1-30 characters. | ||||
| Sstate | 1.3.6.1.4.1.2.3.51.2.23.4.3.7 | OCTET STRING | RW | mandatory |
scalar · OCTET STRING · read-write · mandatory The state of the machine location. 2-3 characters. | ||||
| SpostalCode | 1.3.6.1.4.1.2.3.51.2.23.4.3.8 | OCTET STRING | RW | mandatory |
scalar · OCTET STRING · read-write · mandatory The postal code of the location for this system. 1-9 characters, only alphanumeric characters are valid. | ||||
| SphoneNumberExt | 1.3.6.1.4.1.2.3.51.2.23.4.3.9 | OCTET STRING | RW | mandatory |
scalar · OCTET STRING · read-write · mandatory The phone number extension of the contact person. 1-30 characters. | ||||
| SaltContactName | 1.3.6.1.4.1.2.3.51.2.23.4.3.10 | OCTET STRING | RW | mandatory |
scalar · OCTET STRING · read-write · mandatory The name of the alternate contact person.1-30 characters. | ||||
| SaltPhoneNumber | 1.3.6.1.4.1.2.3.51.2.23.4.3.11 | OCTET STRING | RW | mandatory |
scalar · OCTET STRING · read-write · mandatory The phone of the alternate contact person. 5-30 characters. | ||||
| SaltPhoneNumberExt | 1.3.6.1.4.1.2.3.51.2.23.4.3.12 | OCTET STRING | RW | mandatory |
scalar · OCTET STRING · read-write · mandatory The phone number extension of the alternate contact person. 1-30 characters. | ||||
| SaltEmailAddress | 1.3.6.1.4.1.2.3.51.2.23.4.3.13 | OCTET STRING | RW | mandatory |
scalar · OCTET STRING · read-write · mandatory The email of the alternate contact person. It must contain '@' and dot '.' in form userid@hostname (130 characters maximum). The userid can be alphanumeric characters, '.', '-', or '_' but must begin and end with alphanumeric characters. The hostname can be alphanumeric characters, '.', '-', or '_'. It must contain at least two domain items. Every domain item should begin and end with alphanumeric character, and the last domain item should be 2-20 alphabetic characters. | ||||
| NhttpProxyConfig | 1.3.6.1.4.1.2.3.51.2.23.4.4 | |||
| ShttpProxyEnable | 1.3.6.1.4.1.2.3.51.2.23.4.4.1 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Disable/Enable of the HTTP Proxy. Select Enable to use the proxy for call home connections from the MM to IBM. HTTP Proxy is used by the MM when it is not connected to the internet directly.
| ||||
| ShttpProxyLocation | 1.3.6.1.4.1.2.3.51.2.23.4.4.2 | OCTET STRING | RW | mandatory |
scalar · OCTET STRING · read-write · mandatory Fully qualified host name or IP address of the HTTP Proxy. Maximum of 63 characters. | ||||
| ShttpProxyPort | 1.3.6.1.4.1.2.3.51.2.23.4.4.3 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory The port number of the HTTP Proxy. An integer value from 1 to 65535. | ||||
| ShttpProxyUserName | 1.3.6.1.4.1.2.3.51.2.23.4.4.4 | OCTET STRING | RW | mandatory |
scalar · OCTET STRING · read-write · mandatory User Name of the HTTP Proxy. A maximum of 30 characters string without spaces. | ||||
| ShttpProxyPassword | 1.3.6.1.4.1.2.3.51.2.23.4.4.5 | OCTET STRING | RW | mandatory |
scalar · OCTET STRING · read-write · mandatory Password of the HTTP Proxy. A maximum of 15 characters string without spaces. | ||||
| NactivityLogs | 1.3.6.1.4.1.2.3.51.2.23.4.5 | |||
| TactivityLogTable | 1.3.6.1.4.1.2.3.51.2.23.4.5.1 | NA | mandatory | |
table · not-accessible · mandatory Table of Service Advisor Activity Log entries information. This table displays the last five events that were generated by the system or user that are called home. The entries are displayed in reverse chronological order (most recent call home entry first). For any events that happen with same Date/Time, only one event will be called home. If a call home event that is already in the activity log is triggered again on the same event source, it will not be called home again unless the prior entry has been acknowledged as corrected or 120 hours (5 days) have passed since it initially occurred and was called home. | ||||
| RactivityLogEntry | 1.3.6.1.4.1.2.3.51.2.23.4.5.1.1 | NA | mandatory | |
row · not-accessible · mandatory Activity Log table entry. Each entry has the result of the FTP/TFTP Server attempt, the event ID, event source, date and time that event occured, and a text message.
| ||||
| CactivityLogIndex | 1.3.6.1.4.1.2.3.51.2.23.4.5.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The Activity Log index number. For consistent results, view as a table and not as individual entries. | ||||
| CactivityLogString | 1.3.6.1.4.1.2.3.51.2.23.4.5.1.1.2 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory A string of data detailing one Activity Log entry. The text message is from the original entry in the event log. For consistent results, view as a table and not as individual entries. | ||||
| CactivityLogAcknowledge | 1.3.6.1.4.1.2.3.51.2.23.4.5.1.1.3 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory The acknowledgement of one Activity Log entry as corrected. This field allows the users to set a reminder next to certain events to indicate their awareness of the issue. Checking the acknowledge flag will not cause the event to be removed from the log. This log is not cleared, so the acknowledge flag can be used to indicate a problem can be ignored. This field can be also used to override the 120 hour (5 day) filtering of reports via FTP/TFTP Server of Service Data.
| ||||
| CactivityLogAttribute | 1.3.6.1.4.1.2.3.51.2.23.4.5.1.1.4 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory A string of data detailing one Activity Log entry's attribute. Status PENDING indicates that the system is preparing for the event to be called home by collecting data about the systems state. A SUCCESS state indicates that the problem was successfully transmitted to FTP/TFTP Server. The FAILED state indicates that the attempt to transmit the event information was not successful. Additional information may be found in the Event Log. The event ID, event source , date and time are all information from the original entry in the event log. The acknowledged as corrected field is a reminder to certain events to indicate their awareness of the issue. | ||||
| NautoFTPSetup | 1.3.6.1.4.1.2.3.51.2.23.5 | |||
| SautoFTPCallMode | 1.3.6.1.4.1.2.3.51.2.23.5.1 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory This field specifies the automated problem reporting mode. Automated problem reporting mode allows the MM to automatically put service data to a specified server when a call home event is detected. For any call home events that happen with same Date/Time, only one event will be reported. The system will also wait for an interval of 120 hours (5 days) before another identical event can be sent for the same failed component.
| ||||
| SautoFTPCallAddr | 1.3.6.1.4.1.2.3.51.2.23.5.2 | OCTET STRING | RW | mandatory |
scalar · OCTET STRING · read-write · mandatory This field specifies the remote server address of FTP and TFTP. It should be fully qualified hostname or IP address. | ||||
| SautoFTPCallPort | 1.3.6.1.4.1.2.3.51.2.23.5.3 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory This field specifies the port on remote FTP/TFTP server for data transmission. | ||||
| SautoFTPCallUserID | 1.3.6.1.4.1.2.3.51.2.23.5.4 | OCTET STRING | RW | mandatory |
scalar · OCTET STRING · read-write · mandatory This field specifies the user account to login remote FTP server. | ||||
| SautoFTPCallPassword | 1.3.6.1.4.1.2.3.51.2.23.5.5 | OCTET STRING | RW | mandatory |
scalar · OCTET STRING · read-write · mandatory This field specifies the password to login remote FTP server. | ||||
| NcallHomeExclusionEvents | 1.3.6.1.4.1.2.3.51.2.23.6 | |||
| TreadCallHomeExclusionEventTable | 1.3.6.1.4.1.2.3.51.2.23.6.1 | NA | mandatory | |
table · not-accessible · mandatory Table of Call Home Exclusion Event entries information. | ||||
| RreadCallHomeExclusionEventEntry | 1.3.6.1.4.1.2.3.51.2.23.6.1.1 | NA | mandatory | |
row · not-accessible · mandatory Call Home Exclusion Event table entry | ||||
| CreadCallHomeExclusionEventIndex | 1.3.6.1.4.1.2.3.51.2.23.6.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The index number of one Call Home Exclusion Event. For consistent results, view as a table and not as individual entries. | ||||
| CreadCallHomeExclusionEventID | 1.3.6.1.4.1.2.3.51.2.23.6.1.1.2 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The Event ID of one Call Home Exclusion Event entry. For consistent results, view as a table and not as individual entries. | ||||
| SaddCallHomeExclusionEvent | 1.3.6.1.4.1.2.3.51.2.23.6.2 | OCTET STRING | RW | mandatory |
scalar · OCTET STRING · read-write · mandatory Add one call home Event ID into the Call Home Exclusion List. The Event ID is an 8-digit hexadecimal number (0-F) with an optional prefix of '0x' or '0X'. An Event can not be added into the exclusion list if autoFtpMode is disabled. If Service Advisor Terms and Conditions are accepted, an event can be added into the exclusion list. NOTE: Value returned for the GET command is meaningless for this MIB object. | ||||
| SrmCallHomeExclusionEvent | 1.3.6.1.4.1.2.3.51.2.23.6.3 | OCTET STRING | RW | mandatory |
scalar · OCTET STRING · read-write · mandatory Remove one call home Event ID from the Call Home Exclusion List. The Event ID is an 8-digit hexadecimal number (0-F) with an optional prefix of '0x' or '0X'. An event on the exclusion list can not be removed if autoFtpMode is disabled. If Service Advisor Terms and Conditions are accepted, an event on the exclusion list can be removed. NOTE: Value returned for the GET command is meaningless for this MIB object. | ||||
| SrmAllCallHomeExclusionEvent | 1.3.6.1.4.1.2.3.51.2.23.6.4 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Remove all Event IDs from the Call Home Exclusion List. Events on the exclusion list can not be removed if autoFtpMode is disabled. If Service Advisor Terms and Conditions are accepted, events on the exclusion list can be removed. NOTE: Value returned for the GET command is meaningless for this MIB object.
| ||||
| NcomponentPowerServiceReset | 1.3.6.1.4.1.2.3.51.2.23.10 | |||
| TbladePowerServiceResetTable | 1.3.6.1.4.1.2.3.51.2.23.10.1 | NA | mandatory | |
table · not-accessible · mandatory A table providing aux power status and the ability to perform a virtual reseat or hard restart of a blade. | ||||
| RbladePowerServiceResetEntry | 1.3.6.1.4.1.2.3.51.2.23.10.1.1 | NA | mandatory | |
| CbladePowerServiceResetIndex | 1.3.6.1.4.1.2.3.51.2.23.10.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Blade power service reset index. | ||||
| CbladePowerServiceResetBladeId | 1.3.6.1.4.1.2.3.51.2.23.10.1.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The numeric blade slot number.
| ||||
| CbladePowerServiceResetStatus | 1.3.6.1.4.1.2.3.51.2.23.10.1.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Status of the aux power. A value of auxPowerOff(0) indicates that the blade aux power is off. A value of auxPowerOn(1) indicates that the blade aux power is on.
| ||||
| CbladePowerServiceResetCmd | 1.3.6.1.4.1.2.3.51.2.23.10.1.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory NOTE: Do not perform this service reset operation on a node that is currently in a maintenance mode state. See bladeHealthState in bladeSystemStatusTable for maintMode(12) value. To reset the auxiliary power on a blade component, set this object to resetVirtualReseatOperation(1). This will toggle the auxiliary power to the blade and simulate a physical removal and insertion. During the operation, auxiliary power is removed from the component and is then restored. For nodes, the power state will remain off and the user will need to manually power on the node. To perform a hard restart on the blade component, set this object to resetHardRestartOperation(2). This will toggle the reset line to the service processor causing it to re-initialize. The service processor on the component is directly reset, but the power state of the component will not be affected by this operation. This object is intended to be write-only. The component will experience a temporary loss of communication and the power state will change. Prior to executing this action, perform any operations needed to protect user data. Reading this object will always return the value of noOperation(0).
| ||||
| TsmPowerServiceResetTable | 1.3.6.1.4.1.2.3.51.2.23.10.2 | NA | mandatory | |
table · not-accessible · mandatory A table providing aux power status and the ability to perform a virtual reseat or hard restart of a switch. | ||||
| RsmPowerServiceResetEntry | 1.3.6.1.4.1.2.3.51.2.23.10.2.1 | NA | mandatory | |
row · not-accessible · mandatory Switch module power service reset entry | ||||
| CsmPowerServiceResetIndex | 1.3.6.1.4.1.2.3.51.2.23.10.2.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Switch module power service reset index. | ||||
| CsmPowerServiceResetSwitchId | 1.3.6.1.4.1.2.3.51.2.23.10.2.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The switch module numeric identifier.
| ||||
| CsmPowerServiceResetStatus | 1.3.6.1.4.1.2.3.51.2.23.10.2.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Status of the aux power power. A value of auxPowerOff(0) indicates that the switch aux power is off. A value of auxPowerOn(1) indicates that the switch aux power is on.
| ||||
| CsmPowerServiceResetCmd | 1.3.6.1.4.1.2.3.51.2.23.10.2.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory To reset the auxiliary power on a switch component, set this object to resetVirtualReseatOperation(1). This will toggle the auxiliary power to the switch and simulate a physical removal and insertion. During the operation, auxiliary power is removed from the component and is then restored. For IOMs, the power state will be on after the operation completes. To perform a hard restart on the switch component, set this object to resetHardRestartOperation(2). This will toggle the reset line to the service processor causing it to re-initialize. The service processor on the component is directly reset, but the power state of the component will not be affected by this operation. This object is intended to be write-only. The component will experience a temporary loss of communication and the power state will change. Prior to executing this action, perform any operations needed to protect user data. Reading this object will always return the value of noOperation(0).
| ||||
| NcomponentServiceData | 1.3.6.1.4.1.2.3.51.2.23.15 | |||
| TcomponentServiceDataTable | 1.3.6.1.4.1.2.3.51.2.23.15.1 | NA | mandatory | |
table · not-accessible · mandatory Table of component service data information. | ||||
| RcomponentServiceDataEntry | 1.3.6.1.4.1.2.3.51.2.23.15.1.1 | NA | mandatory | |
| CcomponentServiceDataTopologyPath | 1.3.6.1.4.1.2.3.51.2.23.15.1.1.1 | OCTET STRING (SIZE (0..100)) | RO | mandatory |
column · OCTET STRING (SIZE (0..100)) · read-only · mandatory The unique identifier for a component in this table. The chassis and each installed component is represented by a hardware topology tree, where each node in the tree represents a component. The path to a particular component consists of one or more <component>,<instance> pairs, where each successive pair is a child of the previous parent pair. As an example, the root of the tree is the chassis and is represented by the pair 'CHASSIS, 1'. This pair indicates the first instance of the chassis. If a blade is inserted in slot 4 of the chassis, its topology path is 'CHASSIS, 1, BLADE, 4'. With this format, the components in the chassis can be determined along with their relative hierarchy to each other. This component table is indexed by this unique topology path and the numeric designations for the components are: CHASSIS, 0x01 Chassis MM, 0x02 Management Module BLADE, 0x03 Main system board of a blade POWER, 0x04 Power Supply, Power Module, etc COOLING, 0x05 Fan, blower, or other cooling device IO_MODULE, 0x06 Has I/O interface, i.e. - switch or bridge MEDIA, 0x07 Media device PROCESSOR, 0x08 Any processor, processor module, etc STORAGE, 0x09 Any type of storage device EXPANSION, 0x0A Expansion Card (not covered by more specific type) MEMORY, 0x0B Any memory device, module, etc MFRU, 0x0C Managed FRU Device PANEL, 0x0D Any sort of panel device, such as a front panel BLADE_EXPANSION_MODULE, 0x0E Expansion option (BEM) such as PEU, BSE, etc CARD_EXPANSION, 0x0F Expansion card, ie. daughter card CARD_HS_EXPANSION, 0x10 High Speed Expansion card, ie. daughter card INTERPOSER, 0x11 Interposer device CLOCK, 0x12 Clock card MUX, 0x13 Mulitplexer card ADDIN, 0x14 cKVM card & other addin cards STORAGE_MODULE, 0x15 Container of one or more Storage Devices SYS_EXPANSION_CARD, 0x16 Management card BATTERY, 0x17 A single battery BATTERY_MODULE, 0x18 Container of one or more batteries REAR_LED, 0x19 Rear LED card MEMORY_BANK, 0x1A Memory banks AIR_FILTER, 0x1B Filter mechanism (bezel) SERIAL_PORT_MODULE, 0x1C Container of one or more serial ports PARENT, 0x1D Reference to parent for multi-parent support PHY_PORT, 0x1E Physical port IO_EXPANDER, 0x1F RAID card CABLE, 0x20 Cable/Interconnect FAN_MUX 0x29 Fan multiplexer card PCI_EXPRESS, 0x32 PCI express card on (PEN) FLASH_DIMM, 0x33 Used for SPD devices that matches the silkscreen of the DIMM slot RACK, 0x50 Rack PLATFORM, 0x51 Generic Platform like rack mounted server/appliance DATAPLEX, 0x52 DataPlex OTHER, 0x53 Other unknown etc. PERIPHERAL_MODULE, 0x54 SYSTEM_BOARD, 0x55 System board PROCESSOR_MODULE, 0x56 BACK_PANEL, 0x57 POWER_SYSTEM_BOARD, 0x58 STORAGE_BACKPLANE, 0x59 Drive back plane PROC_BOARD, 0x5A Holds 1 or more processors POWER_DI, 0x5B Power mgt / power distribution board CHASSIS_BACK_PANEL, 0x5C SUB_CHASSIS, 0x5D OTHER_CHASSIS_BOARD, 0x5E DEVICE_MODULE, 0x5F REMOTE_DEVICE, 0x60 Remote mgt communication device EXTERNAL_ENVIRONMENT, 0x61 Such as external temp sensor for outside box temps PROC_MEMORY_MODULE, 0x62 Processors and memory on same module | ||||
| CcomponentServiceDataComponentName | 1.3.6.1.4.1.2.3.51.2.23.15.1.1.2 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The name of the component as a null terminated string. | ||||
| CcomponentServiceDataDumpInitiate | 1.3.6.1.4.1.2.3.51.2.23.15.1.1.3 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Initiates a type of dump collection to be initiated for the component and sent to the MM.
NOTE: Not all components support this, please check componentServiceDataDumpCapabilityMask
OID to see if the action is supported on this component.
For switch modules the serviceData(4) is the only available value that can be set.
When the dump file is created, the node transfers it to the /tftproot/service directory
on the CMM. Only one file can be moved to this directory at a time, so please use the fileManagement
MIB information to check if the file has been completed.
NOTE: Value returned for the GET command is meaningless
for this MIB object.
| ||||
| CcomponentServiceDataDumpRetrieve | 1.3.6.1.4.1.2.3.51.2.23.15.1.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Retrieve a type of service data file from component to MM.
NOTE: This OID only is valid for the last four bit mask designations listed
in the componentServiceDataDumpCapabilityMask OID.
NOTE: This OID is not used for switch modules.
The dump file is transfered to the /tftproot/service directory
on the CMM. Only one file can be moved to this directory at a time,
so please use the fileManagement MIB information to check if the file has been completed.
NOTE: Value returned for the GET command is meaningless
for this MIB object.
| ||||
| CcomponentServiceDataDumpCapabilityMask | 1.3.6.1.4.1.2.3.51.2.23.15.1.1.5 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Indicates whether the component has the capability to trigger service data and if so, which operations are supported and whether the file can be transferred to the MM from the component. The values and meanings are as follows: 0000 0000 means this component does not support any at all. 0000 0001 means this component supports 'processor' type and the file remains on the component. 0000 0010 means this component supports 'platform' type and the file remains on the component. 0000 0100 means this component supports 'partition' type and the file remians on the component. 0000 1000 means this component supports 'processor' type and the file can be transferred to the MM. 0001 0000 means this component supports 'platform' type and the file can be transferred to the MM. 0010 0000 means this component supports 'partition' type and the file can be transferred to the MM 0100 0000 means this component supports 'serviceData' type and the file can be transferred to the MM For example, the returned value of 01111000 means this component supports 'processor','platform', 'partition' and 'serviceData' types, and the file can be transferred to the MM | ||||
| CcomponentServiceDataDumpInProgress | 1.3.6.1.4.1.2.3.51.2.23.15.1.1.6 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory An indicator as to whether a component dump is in progress for the specified component. This object ONLY applies to dumps that can be triggered by the MM and where the dump file is transferred to the MM filesystem upon completion. See the componentServiceDataDumpCapabilityMask object for support levels. The flag that this MIB object represents will be set on when the IPMI command is sent to the component indicating 'init dump' and will be cleared upon receiving the valid dump file from the component or the creation of the text file indicating the problem encountered. If it cannot be determined if the dump is in progress, the unknown(255) value is returned.
| ||||
| CcomponentServiceDataStatus | 1.3.6.1.4.1.2.3.51.2.23.15.1.1.7 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory A status indicator for dump progress. This object ONLY applies to switch modules dumps. | ||||
| CcomponentServiceDataStatusDetails | 1.3.6.1.4.1.2.3.51.2.23.15.1.1.8 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The failure status as a null terminated string. This object ONLY applies to switch modules dumps. | ||||
| ScomponentServiceDataTableCacheTimeout | 1.3.6.1.4.1.2.3.51.2.23.15.2 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory The timeout value (in seconds) of the cached data for the table, componentServiceDataTable. This value is static (constant) and cannot be set. | ||||
| NdownloadMMServiceData | 1.3.6.1.4.1.2.3.51.2.23.21 | |||
| SdownloadMMServiceDataFileCreateAndDownload | 1.3.6.1.4.1.2.3.51.2.23.21.1 | OCTET STRING (SIZE (0..512)) | RW | mandatory |
scalar · OCTET STRING (SIZE (0..512)) · read-write · mandatory Specifying this string initiates the generation of the FFDC (First-Failure Data Capture) data collection (compressed group of files) for the CMM and the download of this file to the specified destination. The destination is a string of chars that specifies the remote location of service data to be saved. Use one of the following protocols: sftp, tftp, ftp, http or https. An example of a qualified location can be: <protocol>://[<user>[:password][;fingerprint=<host>]@]<host> [:<port>]/<path>/<to>/<file> Note: It is recommended that the saved-data filename have an extension of .tgz to allow support personnel to identify the file. Reading this string will always return 'Not readable' since this string may contain a password. | ||||
| SdownloadMMServiceDataStatus | 1.3.6.1.4.1.2.3.51.2.23.21.2 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory An indicator as to whether the FFDC generation and download is in progress. To initiate this process, set the object, downloadMMServiceDataFileCreateAndDownload (see the object's description for details).
| ||||
| SdownloadMMServiceDataResult | 1.3.6.1.4.1.2.3.51.2.23.21.3 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory An indicator as to whether the FFDC generation and download was successful. The FFDC generation and download is started by setting a destination filename with the object, downloadMMServiceDataFileCreateAndDownload. If the FFDC file generation and download process completes successfully, this object is set to complete(5). If the process encounters an error, this object is set to either: permissionFailed(1), fileGenerationFailed(2) or fileDownloadFailed(3). If the process is canceled by the user, this object will be set to canceled(4). A value of none(0) is the default value. This object may be set to none(0) if the object, downloadMMServiceDataStatus, has a value of ready(0). Setting this object to any value other than none(0) will report an error.
| ||||
| SdownloadMMServiceDataCancelDownload | 1.3.6.1.4.1.2.3.51.2.23.21.4 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Set this object to 'cancel(1)' to stop the FFDC file download process. 'cancel(1)' is the only valid value that may be set. The value of this object will be 'cancel(1)' if an user has set this value and an active FFDC download is in progress. After the process has been canceled, this object will automatically be set to 'none(0)'.
| ||||
| Nscaling | 1.3.6.1.4.1.2.3.51.2.24 | |||
| TscalableComplexTable | 1.3.6.1.4.1.2.3.51.2.24.1 | NA | mandatory | |
table · not-accessible · mandatory Table of scalable complex information. This table provides information related to the scalable complexes installed in the chassis. | ||||
| RscalableComplexEntry | 1.3.6.1.4.1.2.3.51.2.24.1.1 | NA | mandatory | |
| CscalableComplexTopologyPath | 1.3.6.1.4.1.2.3.51.2.24.1.1.1 | OCTET STRING (SIZE (0..100)) | RO | mandatory |
column · OCTET STRING (SIZE (0..100)) · read-only · mandatory The unique identifier for a component in this table. The chassis and each installed component is represented by a hardware topology tree, where each node in the tree represents a component. The path to a particular component consists of one or more <component>,<instance> pairs, where each successive pair is a child of the previous parent pair. As an example, the root of the tree is the chassis and is represented by the pair 'CHASSIS, 1'. This pair indicates the first instance of the chassis. If a blade is inserted in slot 4 of the chassis, its topology path is 'CHASSIS, 1, BLADE, 4'. With this format, the components in the chassis can be determined along with their relative hierarchy to each other. This component table is indexed by this unique topology path and the numeric designations for the components are: CHASSIS, 0x01 Chassis MM, 0x02 Management Module BLADE, 0x03 Main system board of a blade POWER, 0x04 Power Supply, Power Module, etc COOLING, 0x05 Fan, blower, or other cooling device IO_MODULE, 0x06 Has I/O interface, i.e. - switch or bridge MEDIA, 0x07 Media device PROCESSOR, 0x08 Any processor, processor module, etc STORAGE, 0x09 Any type of storage device EXPANSION, 0x0A Expansion Card (not covered by more specific type) MEMORY, 0x0B Any memory device, module, etc MFRU, 0x0C Managed FRU Device PANEL, 0x0D Any sort of panel device, such as a front panel BLADE_EXPANSION_MODULE, 0x0E Expansion option (BEM) such as PEU, BSE, etc CARD_EXPANSION, 0x0F Expansion card, ie. daughter card CARD_HS_EXPANSION, 0x10 High Speed Expansion card, ie. daughter card INTERPOSER, 0x11 Interposer device CLOCK, 0x12 Clock card MUX, 0x13 Mulitplexer card ADDIN, 0x14 cKVM card & other addin cards STORAGE_MODULE, 0x15 Container of one or more Storage Devices SYS_EXPANSION_CARD, 0x16 Management card BATTERY, 0x17 A single battery BATTERY_MODULE, 0x18 Container of one or more batteries REAR_LED, 0x19 Rear LED card MEMORY_BANK, 0x1A Memory banks AIR_FILTER, 0x1B Filter mechanism (bezel) SERIAL_PORT_MODULE, 0x1C Container of one or more serial ports PARENT, 0x1D Reference to parent for multi-parent support PHY_PORT, 0x1E Physical port IO_EXPANDER, 0x1F RAID card CABLE, 0x20 Cable/Interconnect FAN_MUX 0x29 Fan multiplexer card PCI_EXPRESS, 0x32 PCI express card on (PEN) FLASH_DIMM, 0x33 Used for SPD devices that matches the silkscreen of the DIMM slot RACK, 0x50 Rack PLATFORM, 0x51 Generic Platform like rack mounted server/appliance DATAPLEX, 0x52 DataPlex OTHER, 0x53 Other unknown etc. PERIPHERAL_MODULE, 0x54 SYSTEM_BOARD, 0x55 System board PROCESSOR_MODULE, 0x56 BACK_PANEL, 0x57 POWER_SYSTEM_BOARD, 0x58 STORAGE_BACKPLANE, 0x59 Drive back plane PROC_BOARD, 0x5A Holds 1 or more processors POWER_DI, 0x5B Power mgt / power distribution board CHASSIS_BACK_PANEL, 0x5C SUB_CHASSIS, 0x5D OTHER_CHASSIS_BOARD, 0x5E DEVICE_MODULE, 0x5F REMOTE_DEVICE, 0x60 Remote mgt communication device EXTERNAL_ENVIRONMENT, 0x61 Such as external temp sensor for outside box temps PROC_MEMORY_MODULE, 0x62 Processors and memory on same module | ||||
| CscalableComplexIdentifier | 1.3.6.1.4.1.2.3.51.2.24.1.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The unique numeric identifier for a complex installed in the chassis. | ||||
| CscalableComplexNodeName | 1.3.6.1.4.1.2.3.51.2.24.1.1.3 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The name of the node as a null terminated string. | ||||
| CscalableComplexNodeHealthState | 1.3.6.1.4.1.2.3.51.2.24.1.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The system health state for the component. Unknown: Component is in an undefined state. Good: Component is operating normally. Warning: One or more outstanding warnings exist for this component. Critical: One or more outstanding critical events for this component. Kernel Mode: Component is in kernel mode. Discovering: The MM is currently in the process of discovering this component. Communications Error: The MM failed to communicate with this component. No Power: No power to the component's domain. Flashing: Flashing in progress. Initialization Failure: Component failed to initialized. Insufficient Power: Not enough power is left in the component's domain to power the component. Power Denied: Power was denied to the component. Maintenance Mode: Node is undergoing a service operation and should not be updated or powered on/off. Firehose Dump: Node is undergoing a storage save operation and should not be udpated or powered on/off
| ||||
| CscalableComplexNodePowerState | 1.3.6.1.4.1.2.3.51.2.24.1.1.5 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates the power state of the node.
| ||||
| CscalableComplexNodeResources | 1.3.6.1.4.1.2.3.51.2.24.1.1.6 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory A string providing a summary overview of the resources provided by this node. | ||||
Textual conventions
InetAddressIPv6OCTET STRING (SIZE (16))Display hint:
2x:2x:2x:2x:2x:2x:2x:2xRepresents an IPv6 network address. Since MIB browsers may require different formats, the address is expected to be the 16 byte address in network-byte order, and shortened formats such as 0::0 are not accepted in SET operations. Two common examples are: The NetSNMP command line will accept SET requests like: snmpset -v1 -cprivate <host> s 2001:00:00:00:FFFF:CCC4:BBB2:AAA6 Other MIB browsers may require the SET request value to be formatted as: # 0x20 0x01 0x00 0x00 0x00 0x00 0x00 0x00 0xFF 0xFF 0xCC 0xC4 0xBB 0xB2 0xAA 0xA6