HUAWEI-MPLSOAM-MIB
HUAWEI Technology Co.,LtdThe HUAWEI-MPLSOAM-MIB contains objects to configure OAM module. The Operation, Administration and Maintenance (OAM) is an effective means for decreasing the cost of network maintenance. The MPLS OAM is used to administrate and maintain MPLS.
snmptranslate -m HUAWEI-MPLSOAM-MIB -Tpsnmpwalk -v2c -c <community> -m HUAWEI-MPLSOAM-MIB <host> 1.3.6.1.4.1.2011.5.12.7Imports
| HUAWEI-MIB | hwMpls |
|---|---|
| HUAWEI-MPLS-EXTEND-MIB | hwMplsTunnelSignalProto, hwMplsTunnelSignalledTunnelName |
| IF-MIB | InterfaceIndex |
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP |
| SNMPv2-SMI | Bits, Integer32, IpAddress, MODULE-IDENTITY, MibIdentifier, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, iso, private |
| SNMPv2-TC | DisplayString, PhysAddress, RowStatus, TEXTUAL-CONVENTION, TimeStamp, TruthValue |
OID tree
| Name | OID | Type | Access | Status |
|---|---|---|---|---|
| IhwMplsOam | 1.3.6.1.4.1.2011.5.12.7 | |||
identity The HUAWEI-MPLSOAM-MIB contains objects to configure OAM module. The Operation, Administration and Maintenance (OAM) is an effective means for decreasing the cost of network maintenance. The MPLS OAM is used to administrate and maintain MPLS. | ||||
| NhwMplsOamPs | 1.3.6.1.4.1.2011.5.12.7.1 | |||
| NhwMplsOamObjects | 1.3.6.1.4.1.2011.5.12.7.1.1 | |||
| ShwMplsOamCapability | 1.3.6.1.4.1.2011.5.12.7.1.1.1 | Unsigned32 (0..2) | RW | |
scalar · Unsigned32 (0..2) · read-write · current Whether OAM is globally capable. 0: incapable; 1: capable; 2: capable(basedItu); The default value is incapable. | ||||
| ThwMplsOamIgrTable | 1.3.6.1.4.1.2011.5.12.7.1.1.2 | NA | ||
table · not-accessible · current This table specifies per-LSP MPLS OAM capability and associated information, such as IgrTunnName and IgrDetType. | ||||
| RhwMplsOamIgrEntry | 1.3.6.1.4.1.2011.5.12.7.1.1.2.1 | NA | ||
row · not-accessible · current An entry in this table is created by an LSR for every LSP capable of supporting MPLS OAM at ingress.
| ||||
| ChwMplsOamIgrIndex | 1.3.6.1.4.1.2011.5.12.7.1.1.2.1.1 | Unsigned32 | AN | |
column · Unsigned32 · accessible-for-notify · current The interface index of the detected tunnel. | ||||
| ChwMplsOamIgrTunnName | 1.3.6.1.4.1.2011.5.12.7.1.1.2.1.2 | OCTET STRING | RC | |
column · OCTET STRING · read-create · current The name of a tunnel. For ingress, it means the tunnel name of the detected LSP. For egress, it means the tunnel name of the reverse LSP. | ||||
| ChwMplsOamIgrDetType | 1.3.6.1.4.1.2011.5.12.7.1.1.2.1.3 | INTEGER | RC | |
column · INTEGER · read-create · current There are two types of OAM packets, CV and FFD. The CV flow is generated at the source LSR of the LSP with a nominal frequency of 1/s and terminated at the sink LSR of the LSP. FFD provides failure detection option for an LSP independent of the CV based availability model and is not tied to the CV insertion rate. Insertion rates at 1/s or faster may also be used. The CV/FFD packet contains a network-unique identifier (TTSI) so that all types of defects can be detected. 1: CV; 2: FFD.
| ||||
| ChwMplsOamIgrDetFreq | 1.3.6.1.4.1.2011.5.12.7.1.1.2.1.4 | INTEGER | RC | |
column · INTEGER · read-create · current For CV: the frequency is static, per second. For FFD: the frequency is set by user. The value can be 10ms, 20ms, 50ms,100ms,200ms,500ms,3ms. Any other frequency is wrong. 0: 1000ms(only for cv); 1: 10ms; 2: 20ms; 3: 50ms; 4: 100ms; 5: 200ms; 6: 500ms; 7: 3ms.
| ||||
| ChwMplsOamIgrRevType | 1.3.6.1.4.1.2011.5.12.7.1.1.2.1.5 | INTEGER | RC | |
column · INTEGER · read-create · current When an LSP is found to be in defect, the sink LSR if the LSP should send BDI to inform the source LSR of the LSP, the BDI is transferred through the reverse LSP. The type of reverse LSP can be private or shared. If private, then the reverse LSP can be used only when the only LSP is in defect; If shared, the reverse LSP which is shared between many forward LSPs, whose source LSRs are the same and sink LSRs are the same. 1: private; 2: share.
| ||||
| ChwMplsOamIgrRevLspName | 1.3.6.1.4.1.2011.5.12.7.1.1.2.1.6 | OCTET STRING | RC | |
column · OCTET STRING · read-create · current The object indicates name of the reverse LSP. | ||||
| ChwMplsOamIgrRevLsrId | 1.3.6.1.4.1.2011.5.12.7.1.1.2.1.7 | IpAddress | RC | |
column · IpAddress · read-create · current Only for ingress, the object indicates the ingress LSR ID of the reverse LSP,, expressed in IP address. | ||||
| ChwMplsOamIgrRevSessTunnId | 1.3.6.1.4.1.2011.5.12.7.1.1.2.1.8 | Integer32 (0..65535) | RC | |
column · Integer32 (0..65535) · read-create · current Only for ingress, the object indicates the session tunnel ID of the reverse LSP. | ||||
| ChwMplsOamIgrEnable | 1.3.6.1.4.1.2011.5.12.7.1.1.2.1.9 | INTEGER | RC | |
column · INTEGER · read-create · current Whether one LSP is OAM enable. If disable, LSP is not monitored; If enable, CV/FFD is generated at the source LSR of the LSP and checked at the sink LSR of the LSP,and user can set other configuration. 0: The OAM function is disabled on the ingress; 1: The OAM function is enabled on the ingress.
| ||||
| ChwMplsOamIgrValid | 1.3.6.1.4.1.2011.5.12.7.1.1.2.1.10 | INTEGER | RO | |
column · INTEGER · read-only · current 0: stop detect; 1: start detect.
| ||||
| ChwMplsOamIgrAvaState | 1.3.6.1.4.1.2011.5.12.7.1.1.2.1.11 | INTEGER | RO | |
column · INTEGER · read-only · current If the LSP Timer (T1) expires, then the LSP enters the Unavailable state. The start point of the Unavailable state is deemed to be at the entry into the LSP defect state. An LSP re-enters the Available state after the LSP Defect state exists first. T1 defines the length of time the LSP is in the Defect state before declaring an LSP Unavailable or returning to defect free state. 0: available state; 1: unavailable state.
| ||||
| ChwMplsOamIgrDefectType | 1.3.6.1.4.1.2011.5.12.7.1.1.2.1.12 | INTEGER | RO | |
column · INTEGER · read-only · current Defect is defined as interruption of the capability of a transport entity (e.g., network connection) to transfer user or OAM information. There are six types of defect: 0: no defect; 1: dServer; 2: dPeerMe; 3: dLOCV, Loss of Connectivity Verification defect; 4: dTTSIMismatch, Trail Termination Source Identifier Mismatch defect; 5: dTTSIMismerge, Trail Termination Source Identifier Mismerge defect; 6: dExcess, Receiving excess rate of CV/FFD; 7: dUnknown, Unknown defect in the MPLS network.. 8: dOamFail, AutoProtocal timer expires. 9: dIngressDown.
| ||||
| ChwMplsOamIgrRowStatus | 1.3.6.1.4.1.2011.5.12.7.1.1.2.1.13 | RowStatus | RC | |
column · RowStatus · read-create · current This variable is used to create, modify, and delete a row in this table. | ||||
| ChwMplsOamIgrCompatibilityMode | 1.3.6.1.4.1.2011.5.12.7.1.1.2.1.14 | INTEGER | RC | |
column · INTEGER · read-create · current 1: PtnMode; 2: RouterMode; Valid only for the ingress configuration.
| ||||
| ChwMplsOamIgrBDIFreq | 1.3.6.1.4.1.2011.5.12.7.1.1.2.1.15 | INTEGER | RC | |
column · INTEGER · read-create · current BDI is generated at the trail termination source point of a return path in response to a defect detected at the trail termination sink point of an LSP in the forwarding direction. The frequency of BDI can be set by user. 1: perSecond; 2: same as detect frequency.
| ||||
| ThwMplsOamEgrTable | 1.3.6.1.4.1.2011.5.12.7.1.1.3 | NA | ||
table · not-accessible · current This table specifies per-LSP MPLS OAM capability and associated information, such as DetectType, DetectFrequency. | ||||
| RhwMplsOamEgrEntry | 1.3.6.1.4.1.2011.5.12.7.1.1.3.1 | NA | ||
row · not-accessible · current An entry in this table is created by an LSR for every LSP capable of supporting MPLS OAM at egress. | ||||
| ChwMplsOamEgrLspName | 1.3.6.1.4.1.2011.5.12.7.1.1.3.1.1 | OCTET STRING | AN | |
column · OCTET STRING · accessible-for-notify · current The object indicates the name of static LSP at egress. | ||||
| ChwMplsOamEgrLsrId | 1.3.6.1.4.1.2011.5.12.7.1.1.3.1.2 | IpAddress | AN | |
column · IpAddress · accessible-for-notify · current The object indicates the Ingress LSR ID of the LSP. | ||||
| ChwMplsOamEgrSessTunnId | 1.3.6.1.4.1.2011.5.12.7.1.1.3.1.3 | Integer32 (0..65535) | AN | |
column · Integer32 (0..65535) · accessible-for-notify · current The object indicates the the Ingress session tunnel ID of the LSP.. | ||||
| ChwMplsOamEgrDetType | 1.3.6.1.4.1.2011.5.12.7.1.1.3.1.4 | INTEGER | RC | |
column · INTEGER · read-create · current 0: invalid, if auto-protocol, this detect type is invalid; 1: CV; 2: FFD.
| ||||
| ChwMplsOamEgrDetFreq | 1.3.6.1.4.1.2011.5.12.7.1.1.3.1.5 | INTEGER | RC | |
column · INTEGER · read-create · current 0: 1000ms(only for cv); 1: 10ms; 2: 20ms; 3: 50ms; 4: 100ms; 5: 200ms; 6: 500ms; 7: invalid; 8: 3ms.
| ||||
| ChwMplsOamEgrRevType | 1.3.6.1.4.1.2011.5.12.7.1.1.3.1.6 | INTEGER | RC | |
column · INTEGER · read-create · current When an LSP is found to be in defect, the sink LSR of the LSP should send BDI to inform the source LSR of the LSP,the BDI is transferred through the reverse LSP. The type of reverse LSP can be private or shared. If private, then the reverse LSP can be used only when the only LSP in defect; If shared, the reverse LSP, which is shared between many forward LSPs that have the same source LSRs and sink LSRs. 0: invalid, when the reverse LSR does not exist; 1: private; 2: share.
| ||||
| ChwMplsOamEgrRevTunnName | 1.3.6.1.4.1.2011.5.12.7.1.1.3.1.7 | OCTET STRING | RC | |
column · OCTET STRING · read-create · current The object indicates the name of a reverse tunnel. | ||||
| ChwMplsOamEgrAutoEn | 1.3.6.1.4.1.2011.5.12.7.1.1.3.1.8 | INTEGER | RC | |
column · INTEGER · read-create · current If autoprotocol, then the egress can process extended FDI sent by ingress. 0: disable; 1: enable; Valid only for the egress configuration.
| ||||
| ChwMplsOamEgrAutoOvertime | 1.3.6.1.4.1.2011.5.12.7.1.1.3.1.9 | Integer32 (0..255) | RC | |
column · Integer32 (0..255) · read-create · current This time is set at the egress. If the egress receives CV/FFD, it records the parameters included in the packet, such as OAM type and frequency. If the egress does not receive any OAM packet before the timer expires, the sink LSR will send BDI with dLOCV defect. Valid only for the egress configuration. | ||||
| ChwMplsOamEgrBDIFreq | 1.3.6.1.4.1.2011.5.12.7.1.1.3.1.10 | INTEGER | RC | |
column · INTEGER · read-create · current BDI is generated at the trail termination source point of a return path in response to a defect detected at the trail termination sink point of an LSP in the forwarding direction. The frequency of BDI can be set by user. Only valid for egress configuration. The default value is detect frequency and it is valid only when a backward-LSP exists. 0: perSecond; 1: same as detect frequency.
| ||||
| ChwMplsOamEgrEnable | 1.3.6.1.4.1.2011.5.12.7.1.1.3.1.11 | INTEGER | RC | |
column · INTEGER · read-create · current Whether one LSP is enabled with OAM. If disable, LSP is not monitored; If enable, CV/FFD is generated at the source LSR of the LSP and checked at the sink LSR of the LSP, and user can set other configuration. 0: The OAM function is disabled on the egress; 1: The OAM function is enabled on the egress.
| ||||
| ChwMplsOamEgrValid | 1.3.6.1.4.1.2011.5.12.7.1.1.3.1.12 | INTEGER | RO | |
column · INTEGER · read-only · current 1: stop detect; 2: start detect.
| ||||
| ChwMplsOamEgrAvaState | 1.3.6.1.4.1.2011.5.12.7.1.1.3.1.13 | INTEGER | RO | |
column · INTEGER · read-only · current If the LSP Timer (T1) expires, then the LSP enters the Unavailable state. The start point of the Unavailable state is deemed to be at the entry into the LSP defect state. An LSP re-enters the Available state after the LSP Defect State. first exists. T1 defines the length of time the LSP is in the Defect state before declaring an LSP Unavailable or returning to defect free state 0: available state; 1: unavailable state.
| ||||
| ChwMplsOamEgrDefectType | 1.3.6.1.4.1.2011.5.12.7.1.1.3.1.14 | INTEGER | RO | |
column · INTEGER · read-only · current 0: no defect; 1: dServer, 2: dPeerMe, 3: dLOCV, Loss of Connectivity Verification defect; 4: dTTSIMismatch, Trail Termination Source Identifier Mismatch defect; 5: dTTSIMismerge, Trail Termination Source Identifier Mismerge defect.; 6: dExcess, Receiving excess rate of CV/FFD; 7: dUnknown, Unknown defect in the MPLS network. 8: dOamFail, AutoProtocal timer expires. 9: dEgressDown.
| ||||
| ChwMplsOamEgrRowStatus | 1.3.6.1.4.1.2011.5.12.7.1.1.3.1.15 | RowStatus | RC | |
column · RowStatus · read-create · current This variable is used to create, modify, and delete a row in this table. | ||||
| ThwMplsOamRlsnTable | 1.3.6.1.4.1.2011.5.12.7.1.1.4 | NA | ||
table · not-accessible · current This table specifies RLSN capability and associated information, such as RlsnLsrId and RlsnLsrId. | ||||
| RhwMplsOamRlsnEntry | 1.3.6.1.4.1.2011.5.12.7.1.1.4.1 | NA | ||
row · not-accessible · current An entry in this table is created by an LSR to binding the name, lsr-id and tunnel-id of the LSP at egress. | ||||
| ChwMplsOamRlsnLspName | 1.3.6.1.4.1.2011.5.12.7.1.1.4.1.1 | OCTET STRING | RC | |
column · OCTET STRING · read-create · current For egress, the object indicates name of the LSP. | ||||
| ChwMplsOamRlsnLsrId | 1.3.6.1.4.1.2011.5.12.7.1.1.4.1.2 | IpAddress | RC | |
column · IpAddress · read-create · current For egress, the object indicates the Ingress LSR ID of the LSP | ||||
| ChwMplsOamRlsnSessTunnId | 1.3.6.1.4.1.2011.5.12.7.1.1.4.1.3 | Integer32 (1..65535) | RC | |
column · Integer32 (1..65535) · read-create · current For egress, the object indicates the Ingress session tunnel ID of the LSP | ||||
| ChwMplsOamRlsnIfIndex | 1.3.6.1.4.1.2011.5.12.7.1.1.4.1.4 | Integer32 | RO | |
column · Integer32 · read-only · current The object indicates the index of outbound interface. | ||||
| ChwMplsOamRlsnIfName | 1.3.6.1.4.1.2011.5.12.7.1.1.4.1.5 | OCTET STRING | RC | |
column · OCTET STRING · read-create · current The object indicates the name of outbound interface. | ||||
| ChwMplsOamRlsnIsDown | 1.3.6.1.4.1.2011.5.12.7.1.1.4.1.6 | INTEGER | RO | |
column · INTEGER · read-only · current 1: up 2: down
| ||||
| ChwMplsOamRlsnRowStatus | 1.3.6.1.4.1.2011.5.12.7.1.1.4.1.7 | RowStatus | RC | |
column · RowStatus · read-create · current This variable is used to create, modify, and delete a row in this table. | ||||
| ShwMplsOamView | 1.3.6.1.4.1.2011.5.12.7.1.1.5 | INTEGER | RC | |
scalar · INTEGER · read-create · current Create or delete the MPLS OAM view. 1: create mplsOam; 0: delete mplsOam;
| ||||
| ThwMplsOamL2vcTable | 1.3.6.1.4.1.2011.5.12.7.1.1.6 | NA | ||
table · not-accessible · current This table specifies PW MPLS OAM capability and associated information, such as DetType and DetFrequence. | ||||
| RhwMplsOamL2vcEntry | 1.3.6.1.4.1.2011.5.12.7.1.1.6.1 | NA | ||
row · not-accessible · current An entry in this table is created by binding the peer-ip, vc-type and vc-id. | ||||
| ChwMplsOamL2vcPeerIp | 1.3.6.1.4.1.2011.5.12.7.1.1.6.1.1 | IpAddress | AN | |
column · IpAddress · accessible-for-notify · current This object indicates the peer ip address. | ||||
| ChwMplsOamL2vcVcType | 1.3.6.1.4.1.2011.5.12.7.1.1.6.1.2 | INTEGER | AN | |
column · INTEGER · accessible-for-notify · current There are seventeen types of vc. 1: fr; 2: atmAal5Sdu; 3: atmTransCell; 4: vlan; 5: ethernet; 6: hdlc; 7: ppp; 9: atmNto1Vcc; 10:atmNto1Vpc; 11:ipLayer2; 12:atm1to1Vcc; 13:atm1to1Vpc; 14:atmAal5Pdu; 16:cep; 17:satopE1; 18:satopT1; 21:cesopsnBasic; 64:ipInterworking; 0:unknown.
| ||||
| ChwMplsOamL2vcVcId | 1.3.6.1.4.1.2011.5.12.7.1.1.6.1.3 | Unsigned32 | AN | |
column · Unsigned32 · accessible-for-notify · current This object indicates the vc id of pw type. | ||||
| ChwMplsOamL2vcRemotePeerIp | 1.3.6.1.4.1.2011.5.12.7.1.1.6.1.4 | IpAddress | RC | |
column · IpAddress · read-create · current This object indicates the remote peer ip address. | ||||
| ChwMplsOamL2vcRemoteVcType | 1.3.6.1.4.1.2011.5.12.7.1.1.6.1.5 | INTEGER | RC | |
column · INTEGER · read-create · current There are seventeen types of vc. 1: fr; 2: atmAal5Sdu; 3: atmTransCell; 4: vlan; 5: ethernet; 6: hdlc; 7: ppp; 9: atmNto1Vcc; 10:atmNto1Vpc; 11:ipLayer2; 12:atm1to1Vcc; 13:atm1to1Vpc; 14:atmAal5Pdu; 16:cep; 17:satopE1; 18:satopT1; 21:cesopsnBasic; 64:ipInterworking; 0:unknown.
| ||||
| ChwMplsOamL2vcRemoteVcId | 1.3.6.1.4.1.2011.5.12.7.1.1.6.1.6 | Unsigned32 | RC | |
column · Unsigned32 · read-create · current This object indicates the remote vc id of pw type. | ||||
| ChwMplsOamL2vcDetType | 1.3.6.1.4.1.2011.5.12.7.1.1.6.1.7 | INTEGER | RC | |
column · INTEGER · read-create · current There are two types of OAM packets, CV and FFD. 1: CV; 2: FFD.
| ||||
| ChwMplsOamL2vcDetFreq | 1.3.6.1.4.1.2011.5.12.7.1.1.6.1.8 | INTEGER | RC | |
column · INTEGER · read-create · current For CV: the frequency is static, per second. For FFD: the frequency is set by user. The value can be 10ms, 20ms, 50ms,100ms,200ms,500ms,3ms. Any other frequency is wrong. 0: 1000ms(only for cv); 1: 10ms; 2: 20ms; 3: 50ms; 4: 100ms; 5: 200ms; 6: 500ms; 7: 3ms.
| ||||
| ChwMplsOamL2vcRevDetType | 1.3.6.1.4.1.2011.5.12.7.1.1.6.1.9 | INTEGER | RO | |
column · INTEGER · read-only · current 0: invalid; 1: CV; 2: FFD.
| ||||
| ChwMplsOamL2vcRevDetFreq | 1.3.6.1.4.1.2011.5.12.7.1.1.6.1.10 | INTEGER | RO | |
column · INTEGER · read-only · current For CV: the frequency is static, per second. For FFD: the frequency is set by user. The value can be 10ms, 20ms, 50ms,100ms,200ms,500ms,3ms. Any other frequency is wrong. 0: 1000ms(only for cv); 1: 10ms; 2: 20ms; 3: 50ms; 4: 100ms; 5: 200ms; 6: 500ms; 7: invalid; 8: 3ms.
| ||||
| ChwMplsOamL2vcSendEnable | 1.3.6.1.4.1.2011.5.12.7.1.1.6.1.11 | INTEGER | RC | |
column · INTEGER · read-create · current 0: The OAM Send function is Disabled; 1: The OAM Send function is Eabled;
| ||||
| ChwMplsOamL2vcReceiveEnable | 1.3.6.1.4.1.2011.5.12.7.1.1.6.1.12 | INTEGER | RC | |
column · INTEGER · read-create · current 0: The OAM Receive function is Disabled; 1: The OAM Receive function is Eabled;
| ||||
| ChwMplsOamL2vcAutoProlEn | 1.3.6.1.4.1.2011.5.12.7.1.1.6.1.13 | INTEGER | RC | |
column · INTEGER · read-create · current 0: disable; 1: enable;
| ||||
| ChwMplsOamL2vcAutoOvertime | 1.3.6.1.4.1.2011.5.12.7.1.1.6.1.14 | Integer32 (0..255) | RC | |
column · Integer32 (0..255) · read-create · current If the oam receives CV/FFD, it records the parameters included in the packet, such as OAM type and frequency. If the oam does not receive any CV/FFD packet before the timer expires, It will send BDI with dLOCV defect. | ||||
| ChwMplsOamL2vcValid | 1.3.6.1.4.1.2011.5.12.7.1.1.6.1.15 | INTEGER | RO | |
column · INTEGER · read-only · current 1: stop detect; 2: start detect; 3: ready.
| ||||
| ChwMplsOamL2vcAvaState | 1.3.6.1.4.1.2011.5.12.7.1.1.6.1.16 | INTEGER | RO | |
column · INTEGER · read-only · current 0: available state; 1: unavailable state.
| ||||
| ChwMplsOamL2vcDefectType | 1.3.6.1.4.1.2011.5.12.7.1.1.6.1.17 | INTEGER | RO | |
column · INTEGER · read-only · current 0: no defect; 1: dServer, 2: dPeerMe, 3: dLOCV, Loss of Connectivity Verification defect; 4: dTTSIMismatch, Trail Termination Source Identifier Mismatch defect; 5: dTTSIMismerge, Trail Termination Source Identifier Mismerge defect.; 6: dExcess, Receiving excess rate of CV/FFD; 7: dUnknown, Unknown defect in the MPLS network. 8: dOamFail, AutoProtocal timer expires. 9: pwDown, PW down.
| ||||
| ChwMplsOamL2vcBdiDefectType | 1.3.6.1.4.1.2011.5.12.7.1.1.6.1.18 | INTEGER | RO | |
column · INTEGER · read-only · current 0: no defect; 1: dServer, 2: dPeerMe, 3: dLOCV, Loss of Connectivity Verification defect; 4: dTTSIMismatch, Trail Termination Source Identifier Mismatch defect; 5: dTTSIMismerge, Trail Termination Source Identifier Mismerge defect.; 6: dExcess, Receiving excess rate of CV/FFD; 7: dUnknown, Unknown defect in the MPLS network. 8: dOamFail, AutoProtocal timer expires.
| ||||
| ChwMplsOamL2vcRowStatus | 1.3.6.1.4.1.2011.5.12.7.1.1.6.1.30 | RowStatus | RC | |
column · RowStatus · read-create · current This variable is used to create, modify, and delete a row in this table. | ||||
| ChwMplsOamL2vcCompatibilityMode | 1.3.6.1.4.1.2011.5.12.7.1.1.6.1.31 | INTEGER | RC | |
column · INTEGER · read-create · current 1: ptnMode; 2: routerMode; Valid only for the l2vc configuration.
| ||||
| ChwMplsOamL2vcBDIFreq | 1.3.6.1.4.1.2011.5.12.7.1.1.6.1.32 | INTEGER | RC | |
column · INTEGER · read-create · current BDI is generated at the trail termination source point of a return path in response to a defect detected at the trail termination sink point of an LSP in the forwarding direction. The frequency of BDI can be set by user. 1: perSecond; 2: same as detect frequency.
| ||||
| ThwMplsOamBidirectionalTunnelTable | 1.3.6.1.4.1.2011.5.12.7.1.1.7 | NA | ||
table · not-accessible · current This table specifies Static Co-Route MPLS OAM capability and associated information, such as DetType and DetFrequence. | ||||
| RhwMplsOamBidirectionalTunnelEntry | 1.3.6.1.4.1.2011.5.12.7.1.1.7.1 | NA | ||
row · not-accessible · current An entry in this table is created by binding the tunnel ifindex. | ||||
| ChwMplsOamBidirectionalTunnelIndex | 1.3.6.1.4.1.2011.5.12.7.1.1.7.1.1 | Unsigned32 | AN | |
column · Unsigned32 · accessible-for-notify · current This is a unique index for an OAM entry in the OAM table. | ||||
| ChwMplsOamBidirectionalTunnelTunnName | 1.3.6.1.4.1.2011.5.12.7.1.1.7.1.2 | OCTET STRING | RC | |
column · OCTET STRING · read-create · current The name of a tunnel. | ||||
| ChwMplsOamBidirectionalTunnelDetType | 1.3.6.1.4.1.2011.5.12.7.1.1.7.1.3 | INTEGER | RC | |
column · INTEGER · read-create · current There are two types of OAM packets, CV and FFD. 1: CV; 2: FFD.
| ||||
| ChwMplsOamBidirectionalTunnelDetFreq | 1.3.6.1.4.1.2011.5.12.7.1.1.7.1.4 | INTEGER | RC | |
column · INTEGER · read-create · current For CV: the frequency is static, per second. For FFD: the frequency is set by user. The value can be 10ms, 20ms, 50ms,100ms,200ms,500ms,3ms. Any other frequency is wrong. 0: 1000ms(only for cv); 1: 10ms; 2: 20ms; 3: 50ms; 4: 100ms; 5: 200ms; 6: 500ms; 7: 3ms.
| ||||
| ChwMplsOamBidirectionalTunnelRevDetType | 1.3.6.1.4.1.2011.5.12.7.1.1.7.1.5 | INTEGER | RO | |
column · INTEGER · read-only · current 0: invalid; 1: CV; 2: FFD.
| ||||
| ChwMplsOamBidirectionalTunnelRevDetFreq | 1.3.6.1.4.1.2011.5.12.7.1.1.7.1.6 | INTEGER | RO | |
column · INTEGER · read-only · current For CV: the frequency is static, per second. For FFD: the frequency is set by user. The value can be 10ms, 20ms, 50ms,100ms,200ms,500ms,3ms. Any other frequency is wrong. 0: 1000ms(only for cv); 1: 10ms; 2: 20ms; 3: 50ms; 4: 100ms; 5: 200ms; 6: 500ms; 7: invalid; 8: 3ms.
| ||||
| ChwMplsOamBidirectionalTunnelSendEnable | 1.3.6.1.4.1.2011.5.12.7.1.1.7.1.7 | INTEGER | RC | |
column · INTEGER · read-create · current 0: The OAM Send function is Disabled; 1: The OAM Send function is Eabled;
| ||||
| ChwMplsOamBidirectionalTunnelReceiveEnable | 1.3.6.1.4.1.2011.5.12.7.1.1.7.1.8 | INTEGER | RC | |
column · INTEGER · read-create · current 0: The OAM Receive function is Disabled; 1: The OAM Receive function is Eabled;
| ||||
| ChwMplsOamBidirectionalTunnelAutoProtocolEnable | 1.3.6.1.4.1.2011.5.12.7.1.1.7.1.9 | INTEGER | RC | |
column · INTEGER · read-create · current 0: disable; 1: enable;
| ||||
| ChwMplsOamBidirectionalTunnelAutoOvertime | 1.3.6.1.4.1.2011.5.12.7.1.1.7.1.10 | Integer32 (0..255) | RC | |
column · Integer32 (0..255) · read-create · current If the oam receives CV/FFD, it records the parameters included in the packet, such as OAM type and frequency. If the oam does not receive any CV/FFD packet before the timer expires, It will send BDI with dLOCV defect. | ||||
| ChwMplsOamBidirectionalTunnelValid | 1.3.6.1.4.1.2011.5.12.7.1.1.7.1.11 | INTEGER | RO | |
column · INTEGER · read-only · current 1: stop detect; 2: start detect; 3: ready.
| ||||
| ChwMplsOamBidirectionalTunnelAvaState | 1.3.6.1.4.1.2011.5.12.7.1.1.7.1.12 | INTEGER | RO | |
column · INTEGER · read-only · current 0: available state; 1: unavailable state.
| ||||
| ChwMplsOamBidirectionalTunnelDefectType | 1.3.6.1.4.1.2011.5.12.7.1.1.7.1.13 | INTEGER | RO | |
column · INTEGER · read-only · current 0: no defect; 1: dServer, 2: dPeerMe, 3: dLOCV, Loss of Connectivity Verification defect; 4: dTTSIMismatch, Trail Termination Source Identifier Mismatch defect; 5: dTTSIMismerge, Trail Termination Source Identifier Mismerge defect.; 6: dExcess, Receiving excess rate of CV/FFD; 7: dUnknown, Unknown defect in the MPLS network. 8: dOamFail, AutoProtocal timer expires. 9: corouteDown, coroute down.
| ||||
| ChwMplsOamBidirectionalTunnelBdiDefectType | 1.3.6.1.4.1.2011.5.12.7.1.1.7.1.14 | INTEGER | RO | |
column · INTEGER · read-only · current 0: no defect; 1: dServer, 2: dPeerMe, 3: dLOCV, Loss of Connectivity Verification defect; 4: dTTSIMismatch, Trail Termination Source Identifier Mismatch defect; 5: dTTSIMismerge, Trail Termination Source Identifier Mismerge defect.; 6: dExcess, Receiving excess rate of CV/FFD; 7: dUnknown, Unknown defect in the MPLS network. 8: dOamFail, AutoProtocal timer expires.
| ||||
| ChwMplsOamBidirectionalTunnelRowStatus | 1.3.6.1.4.1.2011.5.12.7.1.1.7.1.15 | RowStatus | RC | |
column · RowStatus · read-create · current This variable is used to create, modify, and delete a row in this table. | ||||
| ChwMplsOamBidirectionalTunnelCompatibilityMode | 1.3.6.1.4.1.2011.5.12.7.1.1.7.1.16 | INTEGER | RC | |
column · INTEGER · read-create · current 1: ptnMode; 2: routerMode; Valid only for the bidirectional tunnel configuration.
| ||||
| ChwMplsOamBidirectionalTunnelBDIFreq | 1.3.6.1.4.1.2011.5.12.7.1.1.7.1.17 | INTEGER | RC | |
column · INTEGER · read-create · current BDI is generated at the trail termination source point of a return path in response to a defect detected at the trail termination sink point of an LSP in the forwarding direction. The frequency of BDI can be set by user. 1: perSecond; 2: same as detect frequency.
| ||||
| ShwMplsOamTrapOpen | 1.3.6.1.4.1.2011.5.12.7.1.1.8 | Unsigned32 (0..1) | RW | |
scalar · Unsigned32 (0..1) · read-write · current 0: disable 1: enable | ||||
| NhwMplsOamNotifications | 1.3.6.1.4.1.2011.5.12.7.1.2 | |||
| !hwMplsOamIgrLSPOutDefect | 1.3.6.1.4.1.2011.5.12.7.1.2.1 | |||
notification · current This notification is generated when the LSP is found not in the defect state at the LSP ingress. | ||||
| !hwMplsOamIgrLSPInDefect | 1.3.6.1.4.1.2011.5.12.7.1.2.2 | |||
notification · current This notification is generated when the LSP is found in the defect state at the LSP ingress. | ||||
| !hwMplsOamIgrLSPAva | 1.3.6.1.4.1.2011.5.12.7.1.2.3 | |||
notification · current This notification is generated when the LSP is found in the available state at the LSP ingress. | ||||
| !hwMplsOamIgrLSPUnAva | 1.3.6.1.4.1.2011.5.12.7.1.2.4 | |||
notification · current This notification is generated when the LSP is found in the unavailable state at the LSP ingress. | ||||
| !hwMplsOamEgrLSPOutDefect | 1.3.6.1.4.1.2011.5.12.7.1.2.5 | |||
notification · current This notification is generated when the LSP is found not in the defect state at the LSP egress. | ||||
| !hwMplsOamEgrLSPInDefect | 1.3.6.1.4.1.2011.5.12.7.1.2.6 | |||
notification · current This notification is generated when the LSP is found in the defect state at the LSP egress. | ||||
| !hwMplsOamEgrLSPAva | 1.3.6.1.4.1.2011.5.12.7.1.2.7 | |||
notification · current This notification is generated when the LSP is found in the available state at the LSP egress. | ||||
| !hwMplsOamEgrLSPUnAva | 1.3.6.1.4.1.2011.5.12.7.1.2.8 | |||
notification · current This notification is generated when the LSP is found in the unavailable state at the LSP egress. | ||||
| !hwMplsOamEgrFirstPkt | 1.3.6.1.4.1.2011.5.12.7.1.2.9 | |||
notification · current If autoprotocol is enabled, this notification is generated when egress receives the first CV/FFD packet. | ||||
| !hwMplsOamEgrAutoProFDI | 1.3.6.1.4.1.2011.5.12.7.1.2.10 | |||
notification · current The FDI packet is used by the upstream node in an LSP to inform the egress of the defect information. It is also generated when the auto protocol is enabled, with which the LSP ingress notifies the egress to stop the OAM detection. | ||||
| !hwMplsOamEgrRlsnDown | 1.3.6.1.4.1.2011.5.12.7.1.2.11 | |||
notification · current This notification is generated when the Rlsn is down. | ||||
| !hwMplsOamL2vcOutDefect | 1.3.6.1.4.1.2011.5.12.7.1.2.12 | |||
notification · current OAM detected that the local L2VC exited the defect state. | ||||
| !hwMplsOamL2vcInDefect | 1.3.6.1.4.1.2011.5.12.7.1.2.13 | |||
notification · current OAM detected that the local L2VC entered the defect state. | ||||
| !hwMplsOamL2vcAva | 1.3.6.1.4.1.2011.5.12.7.1.2.14 | |||
notification · current OAM detected that the local L2VC entered the available state. | ||||
| !hwMplsOamL2vcUnAva | 1.3.6.1.4.1.2011.5.12.7.1.2.15 | |||
notification · current OAM detected that the local L2VC entered the unavailable state. | ||||
| !hwMplsOamBidirectionalTunnelOutDefect | 1.3.6.1.4.1.2011.5.12.7.1.2.16 | |||
notification · current This notification is generated when the CO-ROUTE is found not in the defect state. | ||||
| !hwMplsOamBidirectionalTunnelInDefect | 1.3.6.1.4.1.2011.5.12.7.1.2.17 | |||
notification · current This notification is generated when the CO-ROUTE is found in the defect state. | ||||
| !hwMplsOamBidirectionalTunnelAva | 1.3.6.1.4.1.2011.5.12.7.1.2.18 | |||
notification · current This notification is generated when the CO-ROUTE is found in the available state. | ||||
| !hwMplsOamBidirectionalTunnelUnAva | 1.3.6.1.4.1.2011.5.12.7.1.2.19 | |||
notification · current This notification is generated when the CO-ROUTE is found in the unavailable state. | ||||
| NhwMplsPsObjects | 1.3.6.1.4.1.2011.5.12.7.1.3 | |||
| ThwMplsPsTable | 1.3.6.1.4.1.2011.5.12.7.1.3.1 | NA | ||
table · not-accessible · current This table specifies per-protection-group MPLS PS capability and associated information. | ||||
| RhwMplsPsEntry | 1.3.6.1.4.1.2011.5.12.7.1.3.1.1 | NA | ||
row · not-accessible · current An entry in this table is created by an LSR for every protection group capable of supporting mpls ps.
| ||||
| ChwMplsPsIndex | 1.3.6.1.4.1.2011.5.12.7.1.3.1.1.1 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current This is a unique index for an entry in the mplspsEntry. | ||||
| ChwMplsPsType | 1.3.6.1.4.1.2011.5.12.7.1.3.1.1.2 | Integer32 (1..4) | RO | |
column · Integer32 (1..4) · read-only · current The type of protection switch,can be 1:1,1+1,shared mesh, packet 1+1,the default choice is 1:1. In the 1+1 architecture type, a protection LSP is dedicated to each working LSP with the working LSP bridged onto the protection LSP at the source of the protection domain. The traffic on working and protection LSPs is transmitted simultaneously to the sink of the protection domain, where a selection between the working and protection LSP is made, based on some predetermined criteria, such as defect indication. In the 1:1 architecture type, a protection LSP is dedicated to each working LSP. The working traffic is transmitted either by working or protection LSP. In the shared mesh architecture type, possible sharing of protection capacity between disjoint link, node in the network is achieved while guaranteeing recovery from a single failure. In the packet 1+1 architecture type, the traffic is transmitted simultaneously onto two possibly disjoint routed LSPs to the sink of the protection domain. Each pair of duplicate transmitted packets is assigned the same identifier (sequence number) but distinct from the other pairs of duplicate packets. At the sink of the protection domain packet level selection mechanism is employed to select one of the two possibly received copies of each packet. 1: 1:1 protection switching,; 2: 1+1 protection switching; 3: shared mesh protection swiching; 4: packet 1+1 protection switching. | ||||
| ChwMplsPsWorkTunnName | 1.3.6.1.4.1.2011.5.12.7.1.3.1.1.3 | OCTET STRING | RO | |
column · OCTET STRING · read-only · current The name of work-tunnel. | ||||
| ChwMplsPsWorkTunnId | 1.3.6.1.4.1.2011.5.12.7.1.3.1.1.4 | Integer32 (1..65535) | RO | |
column · Integer32 (1..65535) · read-only · current Work-tunnel id(session-tunnel-id). | ||||
| ChwMplsPsProtectTunnName | 1.3.6.1.4.1.2011.5.12.7.1.3.1.1.5 | OCTET STRING | RO | |
column · OCTET STRING · read-only · current The name of protect-tunnel. | ||||
| ChwMplsPsProtectTunnId | 1.3.6.1.4.1.2011.5.12.7.1.3.1.1.6 | Integer32 (1..65535) | RO | |
column · Integer32 (1..65535) · read-only · current Protect-tunnel id(session-tunnel-id). | ||||
| ChwMplsPsRevertiveMode | 1.3.6.1.4.1.2011.5.12.7.1.3.1.1.7 | Integer32 (1..2) | RO | |
column · Integer32 (1..2) · read-only · current Revertive mode is a protection switching mode where revertive action (switch back to the working LSP) is taken after the working LSP is repaired.And switching does not occur in a non-revertive mode. 1: revertive; 2: non-revertive; | ||||
| ChwMplsPsWTR | 1.3.6.1.4.1.2011.5.12.7.1.3.1.1.8 | Integer32 (0..60) | RO | |
column · Integer32 (0..60) · read-only · current Wait to Restore timer is only applicable for the revertive mode and applies to a working LSP,It prevents reversion back to select the working LSP until the Wait to Restore timer has expired.The default value is 12 minutes.step is 30s. | ||||
| ChwMplsPsHoldOff | 1.3.6.1.4.1.2011.5.12.7.1.3.1.1.9 | Integer32 (0..100) | RO | |
column · Integer32 (0..100) · read-only · current The time between declaration of signal degrade or signal fail, and the initialization of the protection switching algorithm. step is 100ms.maximum is 10s. | ||||
| ChwMplsPsSwitchCondition | 1.3.6.1.4.1.2011.5.12.7.1.3.1.1.10 | Integer32 (1..9) | RO | |
column · Integer32 (1..9) · read-only · current The current switch condition of the protection group. 1: clear,This command clears all of the externally initiated switch commands listed below; 2: lockout of protection,Fix the selector position on the working LSP,Prevents the selector from switching to the protection LSP when it is selecting the working LSP. Switches the selector from the protection to the working LSP when it is selecting the protection LSP; 3: forced protection,Switches the selector from the working LSP to the protection LSP (unless a higher priority switch request (i.e., LoP) is in effect); 4: signal fail,for 1:1,Signal Fail (SF) is declared when the source of the protection domain enters the Defect State by receiving a BDI packet (from the return LSP or out of band). 5: manual switch for working-lsp,Switches the selector from the working LSP to the protection LSP (unless an equal or higher priority switch request (i.e., LoP, FS, SF or MS) is in effect); 6: manual switch for protection-lsp,Switches the selector from the protection LSP to the working LSP (unless an equal or higher priority switch request (i.e., LoP, FS, SF or MS) is in effect). 7: WTR-timer; 8: HoldOff-timer; 9: Others; The pripority of the commands are: clear > lockout of protection > force switch > manual switch for working lsp = manual switch for protection lsp | ||||
| ChwMplsPsWorkTunnelState | 1.3.6.1.4.1.2011.5.12.7.1.3.1.1.11 | Integer32 (1..2) | RO | |
column · Integer32 (1..2) · read-only · current The state of working tunnel state in one protection group, whether it is in detection, 1: it is outof defect 2: it enters defect | ||||
| ChwMplsPsProtTunnelState | 1.3.6.1.4.1.2011.5.12.7.1.3.1.1.12 | Integer32 (1..2) | RO | |
column · Integer32 (1..2) · read-only · current The state of protection tunnel state in one protection group, whether it is in detection, 1: it is outof defect 2: it enters defect | ||||
| ChwMplsPsSwitchResult | 1.3.6.1.4.1.2011.5.12.7.1.3.1.1.13 | Integer32 (1..2) | RO | |
column · Integer32 (1..2) · read-only · current Which tunnel is used to transfer the data stream. 1: working-tunnel 2: protection-tunnel | ||||
| ChwMplsPsCfgType | 1.3.6.1.4.1.2011.5.12.7.1.3.1.1.14 | Integer32 (1..2) | RO | |
column · Integer32 (1..2) · read-only · current The type of protection switch which is configured. 1: 1:1 2: 1+1 3: shared mesh 4: packet 1:1 | ||||
| ChwMplsPsCfgProtectTunnId | 1.3.6.1.4.1.2011.5.12.7.1.3.1.1.15 | Integer32 (1..65535) | RO | |
column · Integer32 (1..65535) · read-only · current Protect-tunnel id(session-tunnel-id). | ||||
| ChwMplsPsCfgRevertiveMode | 1.3.6.1.4.1.2011.5.12.7.1.3.1.1.16 | Integer32 (1..2) | RO | |
column · Integer32 (1..2) · read-only · current Revertive mode is a protection switching mode where revertive action (switch back to the working LSP) is taken after the working LSP is repaired.And switching does not occur in a non-revertive mode. 1: revertive; 2: non-revertive; | ||||
| ChwMplsPsCfgWTR | 1.3.6.1.4.1.2011.5.12.7.1.3.1.1.17 | Integer32 (0..60) | RO | |
column · Integer32 (0..60) · read-only · current Wait to Restore timer is only applicable for the revertive mode and applies to a working LSP,It prevents reversion back to select the working LSP until the Wait to Restore timer has expired.The default value is 12 minutes.step is 30s. | ||||
| ChwMplsPsCfgHoldOff | 1.3.6.1.4.1.2011.5.12.7.1.3.1.1.18 | Integer32 (0..100) | RO | |
column · Integer32 (0..100) · read-only · current The time between declaration of signal degrade or signal fail, and the initialization of the protection switching algorithm. step is 100ms.maximum is 10s. | ||||
| ChwMplsPsRowStatus | 1.3.6.1.4.1.2011.5.12.7.1.3.1.1.19 | RowStatus | RC | |
column · RowStatus · read-create · current This variable is used to create, modify, and delete a row in this table. 1: active 2: not in service 3: not ready 4: create and go 5: create and wait 6: destroy | ||||
| ChwMplsPsLocalState | 1.3.6.1.4.1.2011.5.12.7.1.3.1.1.20 | Integer32 (0..11) | RO | |
column · Integer32 (0..11) · read-only · current The current local state of the protection group. 0: Lockout of Protection (LO) 1: Signal Fail for Protection (SF-P) 2: Forced Switch (FS) 3: Signal Fail for Working (SF) 4: Signal Degrade for Protection(SD-P) 5: Signal Degrade for Working(SD) 6: Manual Switch (MS) 7: Wait-to-Restore (WTR) 8: Exercise (EXER) 9: Reverse Request(RR) 10: Do Not Revert (DNR) 11: No Request (NR) The pripority of the commands are: LO > SF-P > FS > SF > SD-P > SD > MS > WTR > EXER > RR > DNR > NR | ||||
| ShwTunnPsTrapOpen | 1.3.6.1.4.1.2011.5.12.7.1.3.2 | Unsigned32 (1..2) | RO | |
scalar · Unsigned32 (1..2) · read-only · current 1:enable; 2:disable; | ||||
| ThwMplsVCPsTable | 1.3.6.1.4.1.2011.5.12.7.1.3.3 | NA | ||
table · not-accessible · current Description. | ||||
| RhwMplsVCPsEntry | 1.3.6.1.4.1.2011.5.12.7.1.3.3.1 | NA | ||
row · not-accessible · current this table for these commands
1.mpls te protection tunnel XXX
2. mpls te reverse-lsp { lsp-name XXXX | lsr-id X.X.X.X tunnel-id x }
3. mpls te reserved-for-binding
| ||||
| ChwMplsVCPsIfIndex | 1.3.6.1.4.1.2011.5.12.7.1.3.3.1.1 | InterfaceIndex | RO | |
column · InterfaceIndex · read-only · current The index of working tunnel interface of Protection group | ||||
| ChwMplsVCPsTNLBinding | 1.3.6.1.4.1.2011.5.12.7.1.3.3.1.2 | TruthValue | RC | |
column · TruthValue · read-create · current It is used by command ' mpls te reserved-for-binding ' | ||||
| ChwMplsTeReverseLspName | 1.3.6.1.4.1.2011.5.12.7.1.3.3.1.3 | OCTET STRING | RC | |
column · OCTET STRING · read-create · current It is used for command ' mpls te reverse-lsp lspname' | ||||
| ChwMplsVcPsRowStatus | 1.3.6.1.4.1.2011.5.12.7.1.3.3.1.4 | RowStatus | RC | |
column · RowStatus · read-create · current 1: active; 2: notInservice; 3: notReady; 4: CreateAndGo; 5: CreateAndWait; 6: destroy; | ||||
| ChwMplsTeReverseLspLsrId | 1.3.6.1.4.1.2011.5.12.7.1.3.3.1.5 | IpAddress | RC | |
column · IpAddress · read-create · current It is used for command ' mpls te reverse-lsp lsr-id X.X.X.X tunnel-id XX' | ||||
| ChwMplsTeReverseLspTunnId | 1.3.6.1.4.1.2011.5.12.7.1.3.3.1.6 | Integer32 (1..65535) | RC | |
column · Integer32 (1..65535) · read-create · current It is used for command ' mpls te reverse-lsp lsr-id X.X.X.X tunnel-id XX' | ||||
| ShwMplsApsMismatchReason | 1.3.6.1.4.1.2011.5.12.7.1.3.4 | INTEGER | AN | |
scalar · INTEGER · accessible-for-notify · current Indicates the alarm reason as below: 1. Bridge type mismatch, one side is 1:1 (Selector Bridge) protection, the other side is 1+1 (Permanent Bridge) protection; 2. Channel type mismatch, one side has APS channel, the other side has no APS channel; 3. Switching type mismatch, one side is bidirectional switching, the other side is unidirectional switching; 4. Operation type mismatch, one side is revertive operation, the other side is non-revertive operation; 5. Traffic request mismatch, one side selects working connection, the other side selects protection connection;
| ||||
| NhwMplsPsNotifications | 1.3.6.1.4.1.2011.5.12.7.1.4 | |||
| !hwMplsPsSwitchPtoW | 1.3.6.1.4.1.2011.5.12.7.1.4.1 | |||
notification · current This notification is generated when switching from protection-lsp to working-lsp occured. | ||||
| !hwMplsPsSwitchWtoP | 1.3.6.1.4.1.2011.5.12.7.1.4.2 | |||
notification · current This notification is generated when switching from woking-lsp to protection-lsp occured. | ||||
| !hwMplsApsMismatch | 1.3.6.1.4.1.2011.5.12.7.1.4.3 | |||
notification · current Trap information indicates fully incompatible provisioning and working/protection configuration mismatch are detected by APS frame. | ||||
| !hwMplsApsMismatchRecovery | 1.3.6.1.4.1.2011.5.12.7.1.4.4 | |||
notification · current Trap information indicates fully incompatible provisioning and working/protection configuration mismatch recovery are detected by APS frame. | ||||
| !hwMplsApsLost | 1.3.6.1.4.1.2011.5.12.7.1.4.5 | |||
notification · current Tunnel protection group did not receive APS frames from protection tunnel. | ||||
| !hwMplsApsLostRecovery | 1.3.6.1.4.1.2011.5.12.7.1.4.6 | |||
notification · current Tunnel protection group received APS frames from protection tunnel. | ||||
| !hwMplsApsOutage | 1.3.6.1.4.1.2011.5.12.7.1.4.7 | |||
notification · current Tunnel protection group changed to defect state. | ||||
| !hwMplsApsOutageRecovery | 1.3.6.1.4.1.2011.5.12.7.1.4.8 | |||
notification · current Tunnel protection group recovered from defect state. | ||||
| !hwMplsApsDegraded | 1.3.6.1.4.1.2011.5.12.7.1.4.9 | |||
notification · current Protection tunnel changed to defect state. | ||||
| !hwMplsApsDegradedRecovery | 1.3.6.1.4.1.2011.5.12.7.1.4.10 | |||
notification · current Protection tunnel recovered from defect state. | ||||
| !hwMplsApsSwitchFail | 1.3.6.1.4.1.2011.5.12.7.1.4.11 | |||
notification · current Tunnel protection group changed to defect state. | ||||
| !hwMplsApsSwitchFailRecovery | 1.3.6.1.4.1.2011.5.12.7.1.4.12 | |||
notification · current Tunnel protection group recovered from defect state. | ||||
| !hwMplsApsPathMisMatch | 1.3.6.1.4.1.2011.5.12.7.1.4.13 | |||
notification · current Working or protection path mismatch are detected by APS frame. | ||||
| !hwMplsApsPathMisMatchRecovery | 1.3.6.1.4.1.2011.5.12.7.1.4.14 | |||
notification · current Working or protection path mismatch recovery are detected by APS frame. | ||||
| !hwMplsApsTypeMisMatch | 1.3.6.1.4.1.2011.5.12.7.1.4.15 | |||
notification · current Working or protection type mismatch are detected by APS frame. | ||||
| !hwMplsApsTypeMisMatchRecovery | 1.3.6.1.4.1.2011.5.12.7.1.4.16 | |||
notification · current Working or protection type mismatch recovery are detected by APS frame. | ||||
| NhwMplsOamPsConformance | 1.3.6.1.4.1.2011.5.12.7.1.100 | |||
| NhwMplsOamPsCompliances | 1.3.6.1.4.1.2011.5.12.7.1.100.1 | |||
| MhwMplsOamPsGroupCompliance | 1.3.6.1.4.1.2011.5.12.7.1.100.1.1 | |||
| NhwMplsOamPsGroups | 1.3.6.1.4.1.2011.5.12.7.1.100.2 | |||
| GhwMplsPsGroup | 1.3.6.1.4.1.2011.5.12.7.1.100.2.1 | |||
group · current The compliance statement for mpls oam ps management.
| ||||
| GhwMplsVcPsGroup | 1.3.6.1.4.1.2011.5.12.7.1.100.2.2 | |||
group · current The compliance statement for mpls oam ps reverse lsp. | ||||
| GhwMplsPsNotificationGroup | 1.3.6.1.4.1.2011.5.12.7.1.100.2.3 | |||
| NhwMplsOamObjectConformance | 1.3.6.1.4.1.2011.5.12.7.1.101 | |||
| NhwMplsOamObjectGroups | 1.3.6.1.4.1.2011.5.12.7.1.101.1 | |||
| GhwMplsOamObjectGroup | 1.3.6.1.4.1.2011.5.12.7.1.101.1.1 | |||
group · current The compliance statement for mpls oam all.
| ||||
| GhwMplsOamNotificationGroup | 1.3.6.1.4.1.2011.5.12.7.1.101.1.2 | |||
group · current The compliance statement for mpls oam trap.
| ||||
| NhwMplsOamObjectCompliances | 1.3.6.1.4.1.2011.5.12.7.1.101.2 | |||
Traps / Notifications
- hwMplsApsDegraded
1.3.6.1.4.1.2011.5.12.7.1.4.9 - hwMplsApsDegradedRecovery
1.3.6.1.4.1.2011.5.12.7.1.4.10 - hwMplsApsLost
1.3.6.1.4.1.2011.5.12.7.1.4.5 - hwMplsApsLostRecovery
1.3.6.1.4.1.2011.5.12.7.1.4.6 - hwMplsApsMismatch
1.3.6.1.4.1.2011.5.12.7.1.4.3 - hwMplsApsMismatchRecovery
1.3.6.1.4.1.2011.5.12.7.1.4.4 - hwMplsApsOutage
1.3.6.1.4.1.2011.5.12.7.1.4.7 - hwMplsApsOutageRecovery
1.3.6.1.4.1.2011.5.12.7.1.4.8 - hwMplsApsPathMisMatch
1.3.6.1.4.1.2011.5.12.7.1.4.13 - hwMplsApsPathMisMatchRecovery
1.3.6.1.4.1.2011.5.12.7.1.4.14 - hwMplsApsSwitchFail
1.3.6.1.4.1.2011.5.12.7.1.4.11 - hwMplsApsSwitchFailRecovery
1.3.6.1.4.1.2011.5.12.7.1.4.12 - hwMplsApsTypeMisMatch
1.3.6.1.4.1.2011.5.12.7.1.4.15 - hwMplsApsTypeMisMatchRecovery
1.3.6.1.4.1.2011.5.12.7.1.4.16 - hwMplsOamBidirectionalTunnelAva
1.3.6.1.4.1.2011.5.12.7.1.2.18 - hwMplsOamBidirectionalTunnelInDefect
1.3.6.1.4.1.2011.5.12.7.1.2.17 - hwMplsOamBidirectionalTunnelOutDefect
1.3.6.1.4.1.2011.5.12.7.1.2.16 - hwMplsOamBidirectionalTunnelUnAva
1.3.6.1.4.1.2011.5.12.7.1.2.19 - hwMplsOamEgrAutoProFDI
1.3.6.1.4.1.2011.5.12.7.1.2.10 - hwMplsOamEgrFirstPkt
1.3.6.1.4.1.2011.5.12.7.1.2.9 - hwMplsOamEgrLSPAva
1.3.6.1.4.1.2011.5.12.7.1.2.7 - hwMplsOamEgrLSPInDefect
1.3.6.1.4.1.2011.5.12.7.1.2.6 - hwMplsOamEgrLSPOutDefect
1.3.6.1.4.1.2011.5.12.7.1.2.5 - hwMplsOamEgrLSPUnAva
1.3.6.1.4.1.2011.5.12.7.1.2.8 - hwMplsOamEgrRlsnDown
1.3.6.1.4.1.2011.5.12.7.1.2.11 - hwMplsOamIgrLSPAva
1.3.6.1.4.1.2011.5.12.7.1.2.3 - hwMplsOamIgrLSPInDefect
1.3.6.1.4.1.2011.5.12.7.1.2.2 - hwMplsOamIgrLSPOutDefect
1.3.6.1.4.1.2011.5.12.7.1.2.1 - hwMplsOamIgrLSPUnAva
1.3.6.1.4.1.2011.5.12.7.1.2.4 - hwMplsOamL2vcAva
1.3.6.1.4.1.2011.5.12.7.1.2.14 - hwMplsOamL2vcInDefect
1.3.6.1.4.1.2011.5.12.7.1.2.13 - hwMplsOamL2vcOutDefect
1.3.6.1.4.1.2011.5.12.7.1.2.12 - hwMplsOamL2vcUnAva
1.3.6.1.4.1.2011.5.12.7.1.2.15 - hwMplsPsSwitchPtoW
1.3.6.1.4.1.2011.5.12.7.1.4.1 - hwMplsPsSwitchWtoP
1.3.6.1.4.1.2011.5.12.7.1.4.2