HUAWEI-MPLSLDP-MIB
HUAWEI Technology Co.,LtdThis MIB contains private managed object and notification trap definitions for MPLS LDP.
snmptranslate -m HUAWEI-MPLSLDP-MIB -Tpsnmpwalk -v2c -c <community> -m HUAWEI-MPLSLDP-MIB <host> 1.3.6.1.4.1.2011.5.25.143Imports
| HUAWEI-MIB | hwDatacomm |
|---|---|
| IF-MIB | InterfaceIndex, InterfaceIndexOrZero |
| INET-ADDRESS-MIB | InetAddress |
| MPLS-TC-STD-MIB | MplsLdpIdentifier, MplsLsrIdentifier |
| P-BRIDGE-MIB | EnabledStatus |
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP |
| SNMPv2-SMI | Bits, Counter32, Integer32, IpAddress, MODULE-IDENTITY, MibIdentifier, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, iso |
| SNMPv2-TC | DisplayString, PhysAddress, RowStatus, TEXTUAL-CONVENTION |
OID tree
| Name | OID | Type | Access | Status |
|---|---|---|---|---|
| IhwMplsLdp | 1.3.6.1.4.1.2011.5.25.143 | |||
identity This MIB contains private managed object and notification trap definitions for MPLS LDP. | ||||
| NhwMplsLdpInfo | 1.3.6.1.4.1.2011.5.25.143.1 | |||
| ShwMplsLdpProcessName | 1.3.6.1.4.1.2011.5.25.143.1.1 | OCTET STRING | RO | |
scalar · OCTET STRING · read-only · current This object indicates the process name of LDP running on the router. By default, the value is LDP. | ||||
| ShwMplsLdpLspFec | 1.3.6.1.4.1.2011.5.25.143.1.2 | InetAddress | AN | |
scalar · InetAddress · accessible-for-notify · current This object indicates the destination address of an LSP. The value is either a destination IP address or a prefix of an IP address. | ||||
| ShwMplsLdpLspInLabel | 1.3.6.1.4.1.2011.5.25.143.1.3 | Counter32 | AN | |
scalar · Counter32 · accessible-for-notify · current This object indicates that labels are pushed into all the packets for direct MPLS forwarding. | ||||
| ShwMplsLdpLspOutLabel | 1.3.6.1.4.1.2011.5.25.143.1.4 | Counter32 | AN | |
scalar · Counter32 · accessible-for-notify · current This object indicates that all the packets swap labels for MPLS forwarding. | ||||
| ShwMplsLdpLspOutIfIndex | 1.3.6.1.4.1.2011.5.25.143.1.5 | InterfaceIndex | AN | |
scalar · InterfaceIndex · accessible-for-notify · current The value of this object identifies the index of the outgoing interface of the LSP. | ||||
| ShwMplsLdpLspDownReason | 1.3.6.1.4.1.2011.5.25.143.1.6 | INTEGER | AN | |
scalar · INTEGER · accessible-for-notify · current This object indicates the cause that the LSP becomes Down. Options: 1. routeDelete(1) -indicates that a route has been deleted. 2. lspmNotify(2) -indicates that LSPM notify. 3. canNotRecoveryFromGr(3) -indicates that the recovery from GR was failed. 4. recvReleaseMsg(4) -indicates that the release message was received. 5. recvWithdrawMsg(5) -indicates that the withdraw message was received. 6. upStreamLost(6) -indicates that the upstream route was lost. 7. downStreamLost(7) -indicates that the downstream route was lost. 8. otherReason(8) -indicates that another cause was involved.
| ||||
| ThwMplsLdpSessionTable | 1.3.6.1.4.1.2011.5.25.143.1.7 | NA | ||
table · not-accessible · current This table describes LDP session parameters, including the index of an interface of a session, the cause for a session Down event, and time elapsed since a session was established. | ||||
| RhwMplsLdpSessionEntry | 1.3.6.1.4.1.2011.5.25.143.1.7.1 | NA | ||
row · not-accessible · current This object is used to display the session parameters and session age. The index of this entry is hwMplsLdpSessionPeerLsrId. | ||||
| ChwMplsLdpSessionPeerLsrId | 1.3.6.1.4.1.2011.5.25.143.1.7.1.1 | MplsLdpIdentifier | NA | |
column · MplsLdpIdentifier · not-accessible · current This object indicates the LSR ID of the peer in a session. | ||||
| ChwMplsLdpSessionIfIndex | 1.3.6.1.4.1.2011.5.25.143.1.7.1.2 | Integer32 | AN | |
column · Integer32 · accessible-for-notify · current This object indicates the index of the interface on which the session is established. | ||||
| ChwMplsLdpSessionDownReason | 1.3.6.1.4.1.2011.5.25.143.1.7.1.3 | INTEGER | AN | |
column · INTEGER · accessible-for-notify · current This object indicates the cause that the session becomes Down. Options: 1. sessionUp(0) -indicates that the session was Up. 2. helloHoldTimerExp(1) -indicates that the Hello hold timer expired. 3. ssnHoldTimerExp(2) -indicates that the session hold timer expired. 4. resetMplsLdp(3) -indicates MPLS LDP was reset. 5. undoMplsLdp(4) -indicates that MPLS LDP was disabled. 6. undoMpls(5) -indicates that MPLS was disabled. 7. undoMplsLdpRemotePeer(6) -indicates that the remote peer was deleted. 8. modifyGRConfig(7) -indicates that GR capability was modified. 9. modifyGRTimer(8) -indicates that the GR timer was modified. 10. modifyKeepaliveTimer(9) -indicates that the keepalive timer was modified. 11. modifyMD5Config(10) -indicates that MD5 was configured. 12. ssnRoleSwitch(11) -indicates that the session role was switched. 13. modifyMTUConfig(12) -indicates that the MTU was modified. 14. modifyTransportAddress(13) -indicates that the transport address was modified. 15. modifyLDPLsrID(14) -indicates that the LDP LSR ID was modified. 16. recvNotification(15) -indicates that the notification message was received. 17. transportAddressNotMatch(16) -indicates that the transport address was not matched. 18. protocolGR(17) -indicates that the protocol GR was in processing. 19. ifStatusChanged(18) -indicates that the interface status was changed. 20. tcpDown(19) -indicates that TCP was Down. 21. otherReason(20) -indicates that another cause was involved. 22. sentNotification(21) -indicates that the notification was sent. 23. canntBuildSessionRelation(22) -indicates that the session relation cannot be built. 24. receiveErrorMessageFromPeer(23) -indicates that error message from peer was received. 25. receiveSocketError(24) -indicates that error pakcet from socket was received. 26. sessionDelete(25) -indicates that the session was deleted. 27. modifyCapabilityAnnouncementConfig(26) -indicates that the capability-announcement was modified. 28. modifyLocalLsrID(27) -indicates that the Local LSR ID was modified. 29. modifyP2MP(28) -indicates that the mLDP P2MP was modified. 30. modifyMP2MP(29) -indicates that the mLDP MP2MP was modified. 31. sessionProtectTimerExp(30) -indicates that the session protection timer expired. 32. rlfaIidDel(31) -indicates that IGP deleted the RLFA IID. 33. excessiveMessagesReceived(32) -indicates Excessive messages were received. 34. configICCP(33) -indicates that the ICCP was configured. 35. packetSendReceiveError(34) -indicates that LDP cannot send or receive packets successfully. 36. socketSetOptError(35) -indicates that LDP cannot set the socket option successfully. 37. receiveSocketClose(36) -indicates that LDP received a socket close message.
| ||||
| ChwMplsLdpSessionAge | 1.3.6.1.4.1.2011.5.25.143.1.7.1.4 | TimeTicks | RO | |
column · TimeTicks · read-only · current This object indicates the duration since the session is set up. | ||||
| ThwMplsLdpSessionStateTable | 1.3.6.1.4.1.2011.5.25.143.1.8 | NA | ||
table · not-accessible · current This object is used to display the detailed state parameters of the session. | ||||
| RhwMplsLdpSessionStateEntry | 1.3.6.1.4.1.2011.5.25.143.1.8.1 | NA | ||
row · not-accessible · current This object is used to display the detailed state parameters of the session. The index of this entry is hwMplsLdpSessionPeerId. | ||||
| ChwMplsLdpSessionPeerId | 1.3.6.1.4.1.2011.5.25.143.1.8.1.1 | MplsLdpIdentifier | NA | |
column · MplsLdpIdentifier · not-accessible · current This object indicates the LSR ID of the LDP peer to which the session is connected. | ||||
| ChwMplsLdpSessionLsrId | 1.3.6.1.4.1.2011.5.25.143.1.8.1.2 | MplsLdpIdentifier | RO | |
column · MplsLdpIdentifier · read-only · current This object indicates the ID of the local LSR. | ||||
| ChwMplsLdpSessionTcpConnectionState | 1.3.6.1.4.1.2011.5.25.143.1.8.1.3 | OCTET STRING | RO | |
column · OCTET STRING · read-only · current This object indicates the TCP link status of the session. | ||||
| ChwMplsLdpSessionState | 1.3.6.1.4.1.2011.5.25.143.1.8.1.4 | OCTET STRING | RO | |
column · OCTET STRING · read-only · current This object indicates the current status of the session. | ||||
| ChwMplsLdpSessionRole | 1.3.6.1.4.1.2011.5.25.143.1.8.1.5 | OCTET STRING | RO | |
column · OCTET STRING · read-only · current This object indicates the session roles. | ||||
| ChwMplsLdpSessionFtFlag | 1.3.6.1.4.1.2011.5.25.143.1.8.1.6 | OCTET STRING | RO | |
column · OCTET STRING · read-only · current This object indicates whether the FT of the session is enabled. | ||||
| ChwMplsLdpSessionMd5Flag | 1.3.6.1.4.1.2011.5.25.143.1.8.1.7 | OCTET STRING | RO | |
column · OCTET STRING · read-only · current This object indicates whether the MD5 is enabled for the peer. | ||||
| ChwMplsLdpSessionReconnectTimer | 1.3.6.1.4.1.2011.5.25.143.1.8.1.8 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current This object indicates the value of the GR reconnection timer after the negotiation. Unit: seconds | ||||
| ChwMplsLdpSessionRecoveryTimer | 1.3.6.1.4.1.2011.5.25.143.1.8.1.9 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current This object indicates the value of the GR recovery timer after the negotiation. Unit: seconds | ||||
| ChwMplsLdpSessionKeepAliveTimer | 1.3.6.1.4.1.2011.5.25.143.1.8.1.10 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current This object indicates the value of the KeepAlive timer after the negotiation. Unit: seconds | ||||
| ChwMplsLdpSessionKeepAliveMsgReceived | 1.3.6.1.4.1.2011.5.25.143.1.8.1.11 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current This object indicates the number of the KeepAlive messages that the session obtains. | ||||
| ChwMplsLdpSessionKeepAliveMsgSent | 1.3.6.1.4.1.2011.5.25.143.1.8.1.12 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current This object indicates the number of the KeepAlive messages that the session sends. | ||||
| ChwMplsLdpSessionLabelAdvMode | 1.3.6.1.4.1.2011.5.25.143.1.8.1.13 | OCTET STRING | RO | |
column · OCTET STRING · read-only · current This object indicates the label distribution mode of the session. | ||||
| ChwMplsLdpSessionLocalLabelResourceStatus | 1.3.6.1.4.1.2011.5.25.143.1.8.1.14 | OCTET STRING | RO | |
column · OCTET STRING · read-only · current This object indicates the status of the local label resources of the session. | ||||
| ChwMplsLdpSessionPeerLabelResourceStatus | 1.3.6.1.4.1.2011.5.25.143.1.8.1.15 | OCTET STRING | RO | |
column · OCTET STRING · read-only · current This object indicates the status of the label resources of the LDP peer. | ||||
| ChwMplsLdpSessionAgeStatus | 1.3.6.1.4.1.2011.5.25.143.1.8.1.16 | TimeTicks | RO | |
column · TimeTicks · read-only · current This object indicates the existence time of the session. | ||||
| ShwLdpCapabilityConfig | 1.3.6.1.4.1.2011.5.25.143.1.9 | EnabledStatus | RW | |
scalar · EnabledStatus · read-write · current This object indicates the global configuration or deletion of the LDP capability. Before enabling LDP capability, ensure that the MPLS capability is enabled globally. | ||||
| ShwLdpLsrId | 1.3.6.1.4.1.2011.5.25.143.1.10 | IpAddress | RW | |
scalar · IpAddress · read-write · current This object indicates the way to change the LDP LSR ID. The default LDP LSR ID has the same value as the MPLS LSR ID. It is recommended not to change the LDP LSR ID unless necessary. | ||||
| ShwLdpPropagateIpPrefix | 1.3.6.1.4.1.2011.5.25.143.1.11 | OCTET STRING | RW | |
scalar · OCTET STRING · read-write · current This object indicates the configuration or deletion of the transit policy for the LDP. The object has a valid length ranging from 1 to 169 characters. The length 0 characters shows that the transit policy is deleted. | ||||
| ShwLdpGlobalRemotePwe3 | 1.3.6.1.4.1.2011.5.25.143.1.12 | EnabledStatus | RW | |
scalar · EnabledStatus · read-write · current This object indicates the configuration or deletion of the policy for the LDP remote session. When the object is enabled, it is forbidden to send mapping message to the remote peer. By default, the policy is disabled, which means that there is no limitation to send mapping message to the remote peer. | ||||
| ShwLdpMtuSignaling | 1.3.6.1.4.1.2011.5.25.143.1.13 | EnabledStatus | RW | |
scalar · EnabledStatus · read-write · current This object indicates the configuration or deletion of the MTU signaling function. By default, the MTU signaling function is enabled, and the MTU TLV type in the LDP message is 0x900. | ||||
| ShwLdpMtuApplyTlv | 1.3.6.1.4.1.2011.5.25.143.1.14 | EnabledStatus | RW | |
scalar · EnabledStatus · read-write · current This object conflicts with the object hwLdpMtuSignaling. If the object is enabled, it indicates that the MTU TLV type in the LDP message is 0x601 according to the RFC 3988. | ||||
| ShwLdpGrCapabilityConfig | 1.3.6.1.4.1.2011.5.25.143.1.15 | EnabledStatus | RW | |
scalar · EnabledStatus · read-write · current This object indicates the configuration or deletion of the LDP GR capability. | ||||
| ShwLdpGrNeighborLivenessTimer | 1.3.6.1.4.1.2011.5.25.143.1.16 | Integer32 | RW | |
scalar · Integer32 · read-write · current This object indicates the way to configure the value of GR neighbor life timer. When the status of hwLdpGrCapabilityConfig is enabled, the default value returned by the object is valid. Unit: seconds | ||||
| ShwLdpGrReconnectTimer | 1.3.6.1.4.1.2011.5.25.143.1.17 | Integer32 | RW | |
scalar · Integer32 · read-write · current This object indicates the way to configure the value of GR reconnect timer. When the status of hwLdpGrCapabilityConfig is enabled, the default value returned by the object is valid. Unit: seconds | ||||
| ShwLdpGrRecoveryTimer | 1.3.6.1.4.1.2011.5.25.143.1.18 | Integer32 | RW | |
scalar · Integer32 · read-write · current This object indicates the way to configure the value of GR recovery timer. When the status of hwLdpGrCapabilityConfig is enabled, the default value returned by the object is valid. Unit: seconds | ||||
| ShwMplsLspTrigger | 1.3.6.1.4.1.2011.5.25.143.1.19 | INTEGER | RW | |
scalar · INTEGER · read-write · current This object indicates the way to configure the LDP policy for the ingress LSP and egress LSP.
Options:
1. all(1) -indicates that all FECs are triggered for the IGP.
2. none(2) -indicates that no FEC is triggered for the IGP.
3. host(3) -indicates that the host FEC is triggered for the IGP.
4. ipprefix(4) -indicates that the ip-prefix list is triggered for the IGP.
If the object is set as ipprefix, the value of hwMplsLspTriggerIpPrefix must be set together.
Default: host
| ||||
| ShwMplsLspTriggerIpPrefix | 1.3.6.1.4.1.2011.5.25.143.1.20 | OCTET STRING | RW | |
scalar · OCTET STRING · read-write · current This object indicates the IP prefix when configuring the LDP policy for the ingress LSP and egress LSP. The object has a valid length ranging from 1 to 169 characters. If the object is set with a value, the value of hwMplsLspTrigger must be set as ipprefix. | ||||
| ShwMplsLspTriggerBgpRoute | 1.3.6.1.4.1.2011.5.25.143.1.21 | EnabledStatus | RW | |
scalar · EnabledStatus · read-write · current This object indicates the policy of triggering the BGP route to create the LDP LSP. Default: disabled | ||||
| ShwMplsLspTriggerBgpRouteIpPrefix | 1.3.6.1.4.1.2011.5.25.143.1.22 | OCTET STRING | RW | |
scalar · OCTET STRING · read-write · current This object indicates the IP prefix when triggering the BGP route to create the LDP LSP. The object has a valid length ranging from 1 to 169 characters. | ||||
| ShwLdpReset | 1.3.6.1.4.1.2011.5.25.143.1.23 | INTEGER | RW | |
scalar · INTEGER · read-write · current This object indicates the reset of the LDP protocol. Options: 1. reset(1) -indicates the reset of the LDP protocol. 2. resetall(2) -indicates the reset of all LDP instances. 3. ready(3) -indicates that it is ready to reset LDP. This value cannot be set.
| ||||
| ShwLdpOutBoundSplitHorizonAll | 1.3.6.1.4.1.2011.5.25.143.1.24 | EnabledStatus | RW | |
scalar · EnabledStatus · read-write · current This object indicates the way to set the flag of global split horizon. Default: disabled | ||||
| ShwLdpDeleteGtsmAll | 1.3.6.1.4.1.2011.5.25.143.1.25 | INTEGER | RW | |
scalar · INTEGER · read-write · current This object indicates the deletion of the global GTSM configurations. Options: 1. delete(1) -indicates that global GTSM configurations are to be deleted. 2. ready(2) -indicates that it is ready to delete global GTSM configurations.
| ||||
| ShwMplsFrrLspTrigger | 1.3.6.1.4.1.2011.5.25.143.1.26 | INTEGER | RW | |
scalar · INTEGER · read-write · current This object indicates the way to configure the LDP policy of global instance for LDP Auto FRR. If the object is set as ipprefix, the value of hwMplsFrrLspTriggerIpPrefix must be set together. Default: host Options: 1. all(1) -indicates that all FECs are triggered for the IGP. 2. none(2) -indicates that no FEC is triggered for the IGP. 3. host(3) -indicates that the host FEC is triggered for the IGP. 4. ipprefix(4) -indicates that the ip-prefix list is triggered for the IGP.
| ||||
| ShwMplsFrrLspTriggerIpPrefix | 1.3.6.1.4.1.2011.5.25.143.1.27 | OCTET STRING | RW | |
scalar · OCTET STRING · read-write · current This object indicates the IP prefix when configuring LDP Auto FRR for the public network instance. The object has a valid length ranging from 1 to 169 characters. If the object is set with a value, the value of hwMplsFrrLspTrigger must be set as ipprefix. | ||||
| ShwLdpBackOffTimerInit | 1.3.6.1.4.1.2011.5.25.143.1.28 | Integer32 (5..2147483) | RW | |
scalar · Integer32 (5..2147483) · read-write · current This object indicates the initial value of backoff timer. Default: 15 Unit: seconds | ||||
| ShwLdpBackOffTimerMax | 1.3.6.1.4.1.2011.5.25.143.1.29 | Integer32 (5..2147483) | RW | |
scalar · Integer32 (5..2147483) · read-write · current This object indicates the maximum value of backoff timer. Default: 120 Unit: seconds | ||||
| ShwLdpLongestMatch | 1.3.6.1.4.1.2011.5.25.143.1.30 | EnabledStatus | RW | |
scalar · EnabledStatus · read-write · current This object indicates that the LDP is enabled with the function of searching for routes according to the longest match rule to establish LSPs. Default: disabled | ||||
| ShwLdpRemotePeerAutoDodRequest | 1.3.6.1.4.1.2011.5.25.143.1.37 | EnabledStatus | RW | |
scalar · EnabledStatus · read-write · current The value of this object identifies whether the remote peer is globally enabled with the capability of automatically sending a DoD request. | ||||
| ShwLdpCapabilityAnnouncementConfig | 1.3.6.1.4.1.2011.5.25.143.1.38 | EnabledStatus | RW | |
scalar · EnabledStatus · read-write · current The value of this object identifies whether LDP has Capability-Announcement ability. | ||||
| ThwLdpVpnTable | 1.3.6.1.4.1.2011.5.25.143.1.50 | NA | ||
table · not-accessible · current This object is used to configure or delete the LDP multi-instance. Make sure the relevant VPN instance is already created. | ||||
| RhwLdpVpnEntry | 1.3.6.1.4.1.2011.5.25.143.1.50.1 | NA | ||
row · not-accessible · current This object is used to configure or delete the LDP multi-instance. The index of this entry is hwLdpVpnInstanceId. Make sure the relevant VPN instance is already created.
| ||||
| ChwLdpVpnInstanceId | 1.3.6.1.4.1.2011.5.25.143.1.50.1.1 | Unsigned32 | NA | |
column · Unsigned32 · not-accessible · current This object indicates the ID of the VPN instance. You can find the correct VPN instance ID based on hwL3vpnVrfIndex of hwL3vpnStatisticsTable. | ||||
| ChwLdpVpnLsrId | 1.3.6.1.4.1.2011.5.25.143.1.50.1.11 | IpAddress | RC | |
column · IpAddress · read-create · current This object indicates the way to configure the LDP LSR ID. If the value of the LDP LSR ID is the same as the value of the MPLS LSR ID, the LDP LSR ID is deleted. It is recommended not to change the LDP LSR ID unless necessary. | ||||
| ChwLdpVpnSplitHorizonAll | 1.3.6.1.4.1.2011.5.25.143.1.50.1.12 | EnabledStatus | RC | |
column · EnabledStatus · read-create · current This object indicates the way to set the flag of split horizon for all LDP VPN peers. Default: disabled | ||||
| ChwLdpVpnReset | 1.3.6.1.4.1.2011.5.25.143.1.50.1.13 | INTEGER | RC | |
column · INTEGER · read-create · current This object indicates the reset of the LDP multi-instance corresponding to the VPN. Options: 1.reset(1) -indicates that the LDP multi-instance will be reset. 2.ready(2) -indicates that it is ready to reset ldp multi-instance. This value cannot be set.
| ||||
| ChwMplsVpnFrrLspTrigger | 1.3.6.1.4.1.2011.5.25.143.1.50.1.14 | INTEGER | RC | |
column · INTEGER · read-create · current This object indicates the way to configure the LDP policy of vpn instance for LDP Auto FRR. If the object is set as ipprefix, the value of hwMplsVpnFrrLspTriggerIpPrefix must be set together. Options: 1. all(1) -indicates that all FECs are triggered for the IGP. 2. none(2) -indicates that no FEC is triggered for the IGP. 3. host(3) -indicates that the host FEC is triggered for the IGP. 4. ipprefix(4) -indicates that the ip-prefix list is triggered for the IGP.
| ||||
| ChwMplsVpnFrrLspTriggerIpPrefix | 1.3.6.1.4.1.2011.5.25.143.1.50.1.15 | OCTET STRING | RC | |
column · OCTET STRING · read-create · current This object indicates the IP prefix when configuring the LDP policy of vpn instance for LDP Auto FRR. The object has a valid length ranging from 1 to 169 characters. If the object is set with a value, the value of hwMplsVpnFrrLspTrigger must be set as ipprefix. | ||||
| ChwLdpVpnGracefulDeleteCapability | 1.3.6.1.4.1.2011.5.25.143.1.50.1.16 | EnabledStatus | RC | |
column · EnabledStatus · read-create · current This object indicates whether the LDP graceful-delete capability is enabled for a VPN instance. | ||||
| ChwLdpVpnGracefulDeleteTimer | 1.3.6.1.4.1.2011.5.25.143.1.50.1.17 | Integer32 (1..65535) | RC | |
column · Integer32 (1..65535) · read-create · current The value of this object identifies the value of a graceful-delete timer for a VPN instance. When the status of hwLdpVpnGracefulDeleteCapability is enabled, the default value returned by the object is valid. Default: 5 Unit: seconds | ||||
| ChwLdpVpnRowStatus | 1.3.6.1.4.1.2011.5.25.143.1.50.1.51 | RowStatus | RC | |
column · RowStatus · read-create · current This object indicates whether one entry of hwLdpVpnTable is created or destroyed. The value of this object can be CreatAndGo or Destroy. When the value of the object is set as CreatAndGo, and the entry is correctly created, the status of the object will change into active. | ||||
| ThwLdpRemoteEntityTable | 1.3.6.1.4.1.2011.5.25.143.1.51 | NA | ||
table · not-accessible · current This object is used to configure or delete the LDP remote peer. | ||||
| RhwLdpRemoteEntityEntry | 1.3.6.1.4.1.2011.5.25.143.1.51.1 | NA | ||
row · not-accessible · current This object is used to configure or delete the LDP remote peer. The index of this entry is hwLdpRemoteName.
| ||||
| ChwLdpRemoteName | 1.3.6.1.4.1.2011.5.25.143.1.51.1.1 | DisplayString | NA | |
column · DisplayString · not-accessible · current This object indicates the name of the LDP remote peer. Range: 1-32 characters | ||||
| ChwLdpRemoteIp | 1.3.6.1.4.1.2011.5.25.143.1.51.1.11 | IpAddress | RC | |
column · IpAddress · read-create · current This object indicates the configuration of the remote peer LSR ID. If being set, the ID cannot be modified. To modify the ID, delete the original ID and create a new one. If the ID is set as 0.0.0.0, it indicates that the ID is deleted. | ||||
| ChwLdpRemotePwe3 | 1.3.6.1.4.1.2011.5.25.143.1.51.1.12 | EnabledStatus | RC | |
column · EnabledStatus · read-create · current This object indicates the configuration or deletion of the policy for the remote LDP session. When the object is enabled, it is forbidden to send the mapping message to the remote peer. Default: disabled | ||||
| ChwLdpRemoteKeepaliveTimer | 1.3.6.1.4.1.2011.5.25.143.1.51.1.13 | Integer32 (30..65535) | RC | |
column · Integer32 (30..65535) · read-create · current This object indicates the value of LDP Keepalive timer. Default: 45 Unit: seconds | ||||
| ChwLdpRemoteHelloTimer | 1.3.6.1.4.1.2011.5.25.143.1.51.1.14 | Integer32 (3..65535) | RC | |
column · Integer32 (3..65535) · read-create · current This object indicates the value of LDP Hello hold timer. Default: 45 Unit: seconds | ||||
| ChwLdpRemoteKeepaliveSendTimer | 1.3.6.1.4.1.2011.5.25.143.1.51.1.15 | Integer32 (0..65535) | RC | |
column · Integer32 (0..65535) · read-create · current This object indicates the value of LDP Keepalive send timer. By default, the value of the timer is 0, configuration does not take effect. Default: 0 Unit: seconds | ||||
| ChwLdpRemoteHelloSendTimer | 1.3.6.1.4.1.2011.5.25.143.1.51.1.16 | Integer32 (0..65535) | RC | |
column · Integer32 (0..65535) · read-create · current This object indicates the value of LDP Hello send timer. By default, the value of the timer is 0, configuration does not take effect. Default: 0 Unit: seconds | ||||
| ChwLdpRemoteIgpSyncTimer | 1.3.6.1.4.1.2011.5.25.143.1.51.1.17 | Integer32 (0..65535) | RC | |
column · Integer32 (0..65535) · read-create · current This object indicates the value of IGP-Sync timer. Default: 10 Unit: seconds | ||||
| ChwLdpRemoteIpAutoDoDRequest | 1.3.6.1.4.1.2011.5.25.143.1.51.1.18 | EnabledStatus | RC | |
column · EnabledStatus · read-create · current This object identifies whether the remote peer is enabled with the capability of automatically sending a DoD request. Default: disabled | ||||
| ChwLdpRemoteIpAutoDoDRequestBlock | 1.3.6.1.4.1.2011.5.25.143.1.51.1.19 | EnabledStatus | RC | |
column · EnabledStatus · read-create · current This object indicates whether the remote ip auto dod request function blocked. Default: disabled | ||||
| ChwLdpRemoteLabelAdvertisementMode | 1.3.6.1.4.1.2011.5.25.143.1.51.1.20 | INTEGER | RC | |
column · INTEGER · read-create · current This object indicates the label distribution mode. Options: 1. dod(1) -indicates that the label distribution mode is dod. 2. du(2) -indicates that the label distribution mode is du. Default: du
| ||||
| ChwLdpRemoteLocalLsrIdIfIndex | 1.3.6.1.4.1.2011.5.25.143.1.51.1.21 | InterfaceIndexOrZero | RC | |
column · InterfaceIndexOrZero · read-create · current This object indicates the way to specify the interface that the local LDP LSR-ID based on remote entity is assigned to. Value: 0..2147483647 The default value of the object is the interface that the global LDP LSR ID is assigned to. If the global LDP LSR ID is not assigned to any interface, then the value of the object is 0. If set 0, the value of the object will be the default value. | ||||
| ChwLdpRemoteRowStatus | 1.3.6.1.4.1.2011.5.25.143.1.51.1.51 | RowStatus | RC | |
column · RowStatus · read-create · current This object indicates whether one entry of hwLdpRemoteEntityTable is created or destroyed. The value of this object can be CreatAndGo or Destroy. When the value of the object is set as CreatAndGo, and the entry is correctly created, the status of the object will change into active. | ||||
| ThwLdpPeerTable | 1.3.6.1.4.1.2011.5.25.143.1.52 | NA | ||
table · not-accessible · current This object is used to configure the LDP peer. | ||||
| RhwLdpPeerEntry | 1.3.6.1.4.1.2011.5.25.143.1.52.1 | NA | ||
row · not-accessible · current An entry of the peer feature table, used to configure and display features, such as the MD5 password and split horizon policy negotiated with the local peer. The index of this entry is hwLdpPeerLsrId.
| ||||
| ChwLdpPeerLsrId | 1.3.6.1.4.1.2011.5.25.143.1.52.1.1 | IpAddress | NA | |
column · IpAddress · not-accessible · current This object indicates the LSR ID of the LDP peer. | ||||
| ChwLdpPeerMd5Type | 1.3.6.1.4.1.2011.5.25.143.1.52.1.11 | INTEGER | RC | |
column · INTEGER · read-create · current This object indicates the Md5 type. MD5 is an insecure algorithm and is not recommended. Options: 1. cipher(1) -indicates that the MD5 password is in cipher text mode. 2. plain(2) -indicates that the MD5 password is in plain text mode. 3. null(3) -indicates that the MD5 type is null, which means that the MD5 authentication is not configured for the LDP peer.
| ||||
| ChwLdpPeerMd5Password | 1.3.6.1.4.1.2011.5.25.143.1.52.1.12 | OCTET STRING | RC | |
column · OCTET STRING · read-create · current This object indicates the MD5 password of LDP neighbor. To delete the password, set the password length as zero. When read, it always returns an Octet string with the length of zero. | ||||
| ChwLdpPeerGtsmHops | 1.3.6.1.4.1.2011.5.25.143.1.52.1.13 | Integer32 (0..255) | RC | |
column · Integer32 (0..255) · read-create · current This object indicates the number of GTSM hops. The valid number of GTSM hops ranges from 1 to 255. To clear the configuration of GTSM hops, set the number of GTSM hops as 0. | ||||
| ChwLdpPeerSplitHorizon | 1.3.6.1.4.1.2011.5.25.143.1.52.1.14 | EnabledStatus | RC | |
column · EnabledStatus · read-create · current This object indicates the way to set the flag of split horizon for the specified LDP peer. Default: disabled | ||||
| ChwLdpPeerReset | 1.3.6.1.4.1.2011.5.25.143.1.52.1.15 | INTEGER | RC | |
column · INTEGER · read-create · current This object indicates the reset of the neighbor services. Options: 1. reset(1) -indicates that the neighbor services will be reset. Only when the object is ready, can this value take effect. 2. ready(2) -indicates that it is ready to reset the neighbor services. This value cannot be set.
| ||||
| ChwLdpPeerKeychainName | 1.3.6.1.4.1.2011.5.25.143.1.52.1.18 | OCTET STRING | RC | |
column · OCTET STRING · read-create · current This object indicates the Keychain name. To cancel the Keychain authentication, set the Keychain name length as 0. | ||||
| ChwLdpPeerOutBoundPolicyRange | 1.3.6.1.4.1.2011.5.25.143.1.52.1.19 | INTEGER | RC | |
column · INTEGER · read-create · current This object indicates the range of IGP routes for an outbound policy. The default value is clear. If the object is set as ipprefix, the value of hwLdpPeerOutBoundPolicyFecIpPrefix must be set together. Options: 1. clear(1) -This policy is disabled by default. 2. none(2) -The policy filters out all FECs. 3. ipprefix(3) -The policy allows FECs only in a specified IP prefix to pass through. 4. host(4) -The policy allows FECs only of host routes to pass through.
| ||||
| ChwLdpPeerOutBoundPolicyFecIpPrefix | 1.3.6.1.4.1.2011.5.25.143.1.52.1.20 | OCTET STRING | RC | |
column · OCTET STRING · read-create · current This object indicates the IP prefix list name of IGP routes for an outbound policy. If the object is set with a value, the value of hwLdpPeerOutBoundPolicyRange must be set as ipprefix. | ||||
| ChwLdpPeerOutBoundPolicyBgpRange | 1.3.6.1.4.1.2011.5.25.143.1.52.1.21 | INTEGER | RC | |
column · INTEGER · read-create · current This object indicates the range of BGP routes for an outbound policy. The default value is clear. If the object is set as ipprefix, the value of hwLdpPeerOutBoundPolicyBgpIpPrefix must be set together. Options: 1. clear(1) -This policy is disabled by default. 2. none(2) -The policy filters out all FECs. 3. ipprefix(3) -The policy allows FECs only in a specified IP prefix to pass through.
| ||||
| ChwLdpPeerOutBoundPolicyBgpIpPrefix | 1.3.6.1.4.1.2011.5.25.143.1.52.1.22 | OCTET STRING | RC | |
column · OCTET STRING · read-create · current This object indicates the IP prefix list name of BGP routes for the outbound policy. If the object is set with a value, the value of hwLdpPeerOutBoundPolicyBgpRange must be set as ipprefix. | ||||
| ChwLdpPeerInBoundPolicyRange | 1.3.6.1.4.1.2011.5.25.143.1.52.1.23 | INTEGER | RC | |
column · INTEGER · read-create · current This object indicates the route range for the inbound policy. The default value is clear. If the object is set as ipprefix, the value of hwLdpPeerInBoundPolicyFecIpPrefix must be set together. Options: 1. clear(1) -This policy is disabled by default. 2. none(2) -The policy filters out all FECs. 3. ipprefix(3) -The policy allows FECs only in a specified IP prefix to pass through. 4. host(4) -The policy allows FECs only of host routes to pass through.
| ||||
| ChwLdpPeerInBoundPolicyFecIpPrefix | 1.3.6.1.4.1.2011.5.25.143.1.52.1.24 | OCTET STRING | RC | |
column · OCTET STRING · read-create · current This object indicates the IP prefix list name for the inbound policy. If the object is set with a value, the value of hwLdpPeerInBoundPolicyRange must be set as ipprefix. | ||||
| ChwLdpPeerRowStatus | 1.3.6.1.4.1.2011.5.25.143.1.52.1.51 | RowStatus | RC | |
column · RowStatus · read-create · current This object indicates whether one entry of hwLdpPeerTable is created or destroyed. The value of this object can be CreatAndGo or Destroy. When the value of the object is set as CreatAndGo, and the entry is correctly created, the status of the object will change into active. | ||||
| ThwLdpVpnPeerTable | 1.3.6.1.4.1.2011.5.25.143.1.53 | NA | ||
table · not-accessible · current This table is used to create and delete peer configurations in the LDP multi-instance. Make sure the corresponding LDP VPN-instance is already created in hwLdpVpnTable. | ||||
| RhwLdpVpnPeerEntry | 1.3.6.1.4.1.2011.5.25.143.1.53.1 | NA | ||
row · not-accessible · current An entry of the VPN peer feature table, used to configure and display features, such as the MD5 password and split horizon policy negotiated with the local peer on the VPN. The indexs of this entry are hwLdpVpnInstanceId, hwLdpVpnPeerLsrId. Make sure the corresponding LDP VPN-instance is already created in hwLdpVpnTable. | ||||
| ChwLdpVpnPeerLsrId | 1.3.6.1.4.1.2011.5.25.143.1.53.1.1 | IpAddress | NA | |
column · IpAddress · not-accessible · current This object indicates the LSR ID of the LDP peer. | ||||
| ChwLdpVpnPeerMd5Type | 1.3.6.1.4.1.2011.5.25.143.1.53.1.11 | INTEGER | RC | |
column · INTEGER · read-create · current This object indicates the Md5 type. MD5 is an insecure algorithm and is not recommended. Options: 1. cipher(1) -indicates that the MD5 password is in cipher text mode. 2. plain(2) -indicates that the MD5 password is in plain text mode. 3. null(3) -indicates that the MD5 type is null, which means that the MD5 authentication is not configured for the LDP peer.
| ||||
| ChwLdpVpnPeerMd5Password | 1.3.6.1.4.1.2011.5.25.143.1.53.1.12 | OCTET STRING | RC | |
column · OCTET STRING · read-create · current This object indicates the MD5 password of VPN LDP neighbor. To delete the password, set the password length as zero. When read, it always returns an Octet string with the length of zero. | ||||
| ChwLdpVpnPeerSplitHorizon | 1.3.6.1.4.1.2011.5.25.143.1.53.1.13 | EnabledStatus | RC | |
column · EnabledStatus · read-create · current This object indicates the way to set the flag of split horizon for the specified LDP peer. Default: disabled | ||||
| ChwLdpVpnPeerReset | 1.3.6.1.4.1.2011.5.25.143.1.53.1.14 | INTEGER | RC | |
column · INTEGER · read-create · current This object indicates the reset of the neighbor services. Options: 1. reset(1) -indicates that the neighbor services will be reset. Only when the object is ready, can this value take effect. 2. ready(2) -indicates that it is ready to reset the neighbor services. This value cannot be set.
| ||||
| ChwLdpVpnPeerKeychainName | 1.3.6.1.4.1.2011.5.25.143.1.53.1.17 | OCTET STRING | RC | |
column · OCTET STRING · read-create · current This object indicates the Keychain name. To cancel the Keychain authentication, set the Keychain name length as 0. | ||||
| ChwLdpVpnPeerRowStatus | 1.3.6.1.4.1.2011.5.25.143.1.53.1.51 | RowStatus | RC | |
column · RowStatus · read-create · current This object indicates whether one entry of hwLdpVpnPeerTable is created or destroyed. The value of this object can be CreatAndGo or Destroy. When the value of the object is set as CreatAndGo, and the entry is correctly created, the status of the object will change into active. | ||||
| ThwLdpInterfaceTable | 1.3.6.1.4.1.2011.5.25.143.1.54 | NA | ||
table · not-accessible · current This table is used to configure or delete the LDP capability on the interface. | ||||
| RhwLdpInterfaceEntry | 1.3.6.1.4.1.2011.5.25.143.1.54.1 | NA | ||
row · not-accessible · current An entry of the LDP interface table, used to configure and display the LDP negotiation parameters on the interface enabled with LDP capabilities. The index of this entry is hwLdpInterfaceIndex.
| ||||
| ChwLdpInterfaceIndex | 1.3.6.1.4.1.2011.5.25.143.1.54.1.1 | InterfaceIndex | NA | |
column · InterfaceIndex · not-accessible · current This object indicates the interface index. You can get the correct interface index based on ifIndex of ifTable. | ||||
| ChwLdpStaticFrrProtectTimer | 1.3.6.1.4.1.2011.5.25.143.1.54.1.11 | Integer32 (5..30) | RC | obsolete |
column · Integer32 (5..30) · read-create · obsolete This object indicates the value of static FRR protect timer. Default: 10 Unit: seconds | ||||
| ChwLdpKeepAliveTimer | 1.3.6.1.4.1.2011.5.25.143.1.54.1.12 | Integer32 (30..65535) | RC | |
column · Integer32 (30..65535) · read-create · current This object indicates the value of Keepalive timer. Default: 45 Unit: seconds | ||||
| ChwLdpIgpSyncTimer | 1.3.6.1.4.1.2011.5.25.143.1.54.1.13 | Integer32 (0..65535) | RC | |
column · Integer32 (0..65535) · read-create · current This object indicates the value of IGP-Sync timer. By default, the timer is set to 10 seconds. Default: 10 Unit: seconds | ||||
| ChwLdpHelloTimer | 1.3.6.1.4.1.2011.5.25.143.1.54.1.14 | Integer32 (3..65535) | RC | |
column · Integer32 (3..65535) · read-create · current This object indicates the value of Hello hold timer. By default, the value of the timer is 15 seconds. Default: 15 Unit: seconds | ||||
| ChwLdpTransportAddressIfIndex | 1.3.6.1.4.1.2011.5.25.143.1.54.1.15 | InterfaceIndexOrZero | RC | |
column · InterfaceIndexOrZero · read-create · current This object indicates the way to specify the interface that the Transport Address is assigned to. Value: 0..2147483647 The default value of the object for the public interface is the interface that the LDP LSR ID is assigned to. If the LDP LSR ID is not assigned to any interface, then the value of the object is 0, and 0 cannot be set. The default value of the object for the private interface is the private interface itself. Based on mplsL3VpnIfConfRowStatus of mplsL3VpnIfConfTable, you can find which interface belongs to the VPN. The interface must be bound with the same VPN instance. | ||||
| ChwLdpKeepAliveSendTimer | 1.3.6.1.4.1.2011.5.25.143.1.54.1.16 | Integer32 (0..65535) | RC | |
column · Integer32 (0..65535) · read-create · current This object indicates the value of LDP Keepalive send timer. Default: 0 Unit: seconds | ||||
| ChwLdpHelloSendTimer | 1.3.6.1.4.1.2011.5.25.143.1.54.1.17 | Integer32 (0..65535) | RC | |
column · Integer32 (0..65535) · read-create · current This object indicates the value of LDP Hello send timer. Default: 0 Unit: seconds | ||||
| ChwLdpInterfaceLabelAdvertisementMode | 1.3.6.1.4.1.2011.5.25.143.1.54.1.18 | INTEGER | RC | |
column · INTEGER · read-create · current This object indicates the label distribution mode. Options: 1. dod(1) -indicates that the label distribution mode is dod. 2. du(2) -indicates that the label distribution mode is du. Default: du
| ||||
| ChwLdpInterfaceLocalLsrIdIfIndex | 1.3.6.1.4.1.2011.5.25.143.1.54.1.19 | InterfaceIndexOrZero | RC | |
column · InterfaceIndexOrZero · read-create · current This object indicates the way to specify the interface that the local LDP LSR-ID based on interface is assigned to. Value: 0..2147483647 The default value of the object for the public interface is the interface that the global LDP LSR ID is assigned to. If the global LDP LSR ID is not assigned to any interface, then the value of the object is 0. If set 0, the value of the object will be the default value. The default value of the object for the private interface is the interface that the global LDP LSR ID of VPN Instance is assigned to. Based on mplsL3VpnIfConfRowStatus of mplsL3VpnIfConfTable, you can find which interface belongs to the VPN. The interface which the object specified must be bound with the same VPN instance with the interface which is configured. | ||||
| ChwLdpInterfaceRowStatus | 1.3.6.1.4.1.2011.5.25.143.1.54.1.51 | RowStatus | RC | |
column · RowStatus · read-create · current This object indicates whether one entry of hwLdpInterfaceTable is created or destroyed. The value of this object can be CreatAndGo or Destroy. When the value of the object is set as CreatAndGo, and the entry is correctly created, the status of the object will change into active. | ||||
| ThwLdpPeerGroupTable | 1.3.6.1.4.1.2011.5.25.143.1.58 | NA | ||
table · not-accessible · current This table is used to configure an LDP peer group. | ||||
| RhwLdpPeerGroupEntry | 1.3.6.1.4.1.2011.5.25.143.1.58.1 | NA | ||
| ChwLdpPeerGroupName | 1.3.6.1.4.1.2011.5.25.143.1.58.1.1 | OCTET STRING (SIZE (1..110)) | NA | |
column · OCTET STRING (SIZE (1..110)) · not-accessible · current This object indicates the name of a peer group. | ||||
| ChwLdpPeerGroupOutBoundRange | 1.3.6.1.4.1.2011.5.25.143.1.58.1.11 | INTEGER | RC | |
column · INTEGER · read-create · current This object indicates the range of IGP routes for an outbound policy. The default value is clear. If the object is set as ipprefix, the value of hwLdpPeerGroupOutBoundFecIpPrefix must be set together. Options: 1. clear(1) -This policy is disabled by default. 2. none(2) -The policy filters out all FECs. 3. ipprefix(3) -The policy allows FECs only in a specified IP prefix to pass through. 4. host(4) -The policy allows FECs only of host routes to pass through.
| ||||
| ChwLdpPeerGroupOutBoundFecIpPrefix | 1.3.6.1.4.1.2011.5.25.143.1.58.1.12 | OCTET STRING | RC | |
column · OCTET STRING · read-create · current This object indicates the IP prefix list name of IGP routes for an outbound policy. If the object is set with a value, the value of hwLdpPeerGroupOutBoundRange must be set as ipprefix. | ||||
| ChwLdpPeerGroupOutBoundBgpRange | 1.3.6.1.4.1.2011.5.25.143.1.58.1.13 | INTEGER | RC | |
column · INTEGER · read-create · current This object indicates the range of BGP routes for an outbound policy. The default value is clear. If the object is set as ipprefix, the value of hwLdpPeerGroupOutBoundBgpIpPrefix must be set together. Options: 1. clear(1) -This policy is disabled by default. 2. none(2) -The policy filters out all FECs. 3. ipprefix(3) -The policy allows FECs only in a specified IP prefix to pass through.
| ||||
| ChwLdpPeerGroupOutBoundBgpIpPrefix | 1.3.6.1.4.1.2011.5.25.143.1.58.1.14 | OCTET STRING | RC | |
column · OCTET STRING · read-create · current This object indicates the IP prefix list name of BGP routes for an outbound policy. If the object is set with a value, the value of hwLdpPeerGroupOutBoundBgpRange must be set as ipprefix. | ||||
| ChwLdpPeerGroupInBoundRange | 1.3.6.1.4.1.2011.5.25.143.1.58.1.15 | INTEGER | RC | |
column · INTEGER · read-create · current This object indicates the route range for an inbound policy. The default value is clear. If the object is set as ipprefix, the value of hwLdpPeerGroupInBoundIpPrefix must be set together. Options: 1. clear(1) -This policy is disabled by default. 2. none(2) -The policy filters out all FECs. 3. ipprefix(3) -The policy allows FECs only in a specified IP prefix to pass through. 4. host(4) -The policy allows FECs only of host routes to pass through.
| ||||
| ChwLdpPeerGroupInBoundIpPrefix | 1.3.6.1.4.1.2011.5.25.143.1.58.1.16 | OCTET STRING | RC | |
column · OCTET STRING · read-create · current This object indicates the IP prefix list name of routes for an inbound policy. If the object is set with a value, the value of hwLdpPeerGroupInBoundRange must be set as ipprefix. | ||||
| ChwLdpPeerGroupRowStatus | 1.3.6.1.4.1.2011.5.25.143.1.58.1.51 | RowStatus | RC | |
column · RowStatus · read-create · current This object indicates whether one entry of hwLdpPolicyPeerGroupTable is created or destroyed. The value of this object is CreatAndGo or Destroy. When the value of the object is set to CreatAndGo, and the entry is correctly created, the status of the object will change into active. | ||||
| ShwLdpOutBoundPolicyPeerAllRange | 1.3.6.1.4.1.2011.5.25.143.1.59 | INTEGER | RW | |
scalar · INTEGER · read-write · current This object indicates the range of IGP routes for a global outbound LDP policy. The default value is all. If the object is set as ipprefix, the value of hwLdpOutBoundPolicyPeerAllFecIpPrefix must be set together. Options: 1. all(1) -The default policy allows all LDP peers. 2. none(2) -The policy filters out all FECs. 3. ipprefix(3) -The policy allows FECs only in a specified IP prefix to pass through. 4. host(4) -The policy allows FECs only of host routes to pass through.
| ||||
| ShwLdpOutBoundPolicyPeerAllFecIpPrefix | 1.3.6.1.4.1.2011.5.25.143.1.60 | OCTET STRING | RW | |
scalar · OCTET STRING · read-write · current This object indicates the IP prefix list name of IGP routes for a global outbound LDP policy. The default value is NULL. If the object is set with a value, the value of hwLdpOutBoundPolicyPeerAllRange must be set as ipprefix. | ||||
| ShwLdpOutBoundPolicyPeerAllBgpRange | 1.3.6.1.4.1.2011.5.25.143.1.61 | INTEGER | RW | |
scalar · INTEGER · read-write · current This object indicates the range of BGP routes for a global outbound LDP policy. The default value is all. If the object is set as ipprefix, the value of hwLdpOutBoundPolicyPeerAllBgpIpPrefix must be set together. Options: 1. all(1) -The default policy allows all LDP peers. 2. none(2) -The policy filters out all FECs. 3. ipprefix(3) -The policy allows FECs only in a specified IP prefix to pass through.
| ||||
| ShwLdpOutBoundPolicyPeerAllBgpIpPrefix | 1.3.6.1.4.1.2011.5.25.143.1.62 | OCTET STRING | RW | |
scalar · OCTET STRING · read-write · current This object indicates the IP prefix list name of BGP routes for a global outbound LDP policy. The default value is NULL. If the object is set with a value, the value of hwLdpOutBoundPolicyPeerAllBgpRange must be set as ipprefix. | ||||
| ShwLdpInBoundPolicyPeerAllRange | 1.3.6.1.4.1.2011.5.25.143.1.63 | INTEGER | RW | |
scalar · INTEGER · read-write · current This object indicates the range of routes for a global inbound LDP policy. The default value is all. If the object is set as ipprefix, the value of hwLdpInBoundPolicyPeerAllIpPrefix must be set together. Options: 1. all(1) -The default policy allows all LDP peers. 2. none(2) -The policy filters out all FECs. 3. ipprefix(3) -The policy allows FECs only in a specified IP prefix to pass through. 4. host(4) -The policy allows FECs only of host routes to pass through.
| ||||
| ShwLdpInBoundPolicyPeerAllIpPrefix | 1.3.6.1.4.1.2011.5.25.143.1.64 | OCTET STRING | RW | |
scalar · OCTET STRING · read-write · current This object indicates the IP prefix list name of routes for a global inbound LDP policy. The default value is NULL. If the object is set with a value, the value of hwLdpInBoundPolicyPeerAllRange must be set as ipprefix. | ||||
| ShwLdpGracefulDeleteCapability | 1.3.6.1.4.1.2011.5.25.143.1.65 | EnabledStatus | RW | |
scalar · EnabledStatus · read-write · current This object indicates whether the LDP graceful-delete capability is enabled. | ||||
| ShwLdpGracefulDeleteTimer | 1.3.6.1.4.1.2011.5.25.143.1.66 | Integer32 (1..65535) | RW | |
scalar · Integer32 (1..65535) · read-write · current The value of this object identifies the value of a graceful-delete timer. When the status of hwLdpGracefulDeleteCapability is enabled, the default value returned by the object is valid. Default: 5 Unit: seconds | ||||
| ShwLdpLspDownReason | 1.3.6.1.4.1.2011.5.25.143.1.67 | INTEGER | AN | |
scalar · INTEGER · accessible-for-notify · current The LDP LSP down reason. Options: 1. other(1) -indicates other reasons. 2. session down(2) -indicates the ldp session went down. 3. route change(3) -indicates the route changed. 4. cannot recovery from GR(4) -indicates LSP cannot recovery from graceful-restart. 5. policy change(5) -indicates the policy changed.
| ||||
| ShwLdpLspDownMplsLsrId | 1.3.6.1.4.1.2011.5.25.143.1.68 | MplsLsrIdentifier | AN | |
scalar · MplsLsrIdentifier · accessible-for-notify · current This object indicates the LSR ID of failed router. | ||||
| ShwLdpLspDownOutIfIndex | 1.3.6.1.4.1.2011.5.25.143.1.69 | InterfaceIndex | AN | |
scalar · InterfaceIndex · accessible-for-notify · current This object indicates the outgoing interface index of the failed router. | ||||
| ShwLdpLspDownOutIfMainIp | 1.3.6.1.4.1.2011.5.25.143.1.70 | IpAddress | AN | |
scalar · IpAddress · accessible-for-notify · current This object indicates the main ip address of the failed router's outgoing interface. | ||||
| ShwLdpLspDownOutIfState | 1.3.6.1.4.1.2011.5.25.143.1.71 | INTEGER | AN | |
scalar · INTEGER · accessible-for-notify · current The state of the failed router's outgoing interface. Options: 1. up(1) -indicates that the state of the outgoing interface is Up. 2. down(2) -indicates that the state of the outgoing interface is Down.
| ||||
| ShwLdpLspDownDownstreamPeerLsrId | 1.3.6.1.4.1.2011.5.25.143.1.72 | MplsLdpIdentifier | AN | |
scalar · MplsLdpIdentifier · accessible-for-notify · current This object indicates the failed router's downstream peer's LSR ID. | ||||
| NhwLdpSessionStatistics | 1.3.6.1.4.1.2011.5.25.143.1.73 | |||
| ShwLdpLocalOperationalSessionNumber | 1.3.6.1.4.1.2011.5.25.143.1.73.1 | Integer32 | RO | |
scalar · Integer32 · read-only · current This object indicates the number of local LDP operational sessions. | ||||
| ShwLdpRemoteOperationalSessionNumber | 1.3.6.1.4.1.2011.5.25.143.1.73.2 | Integer32 | RO | |
scalar · Integer32 · read-only · current This object indicates the number of remote LDP operational sessions. | ||||
| ShwLdpLocalAndRemoteOperationalSessionNumber | 1.3.6.1.4.1.2011.5.25.143.1.73.3 | Integer32 | RO | |
scalar · Integer32 · read-only · current This object indicates the number of local and remote LDP operational sessions. | ||||
| ShwLdpTotalOperationalSessionNumber | 1.3.6.1.4.1.2011.5.25.143.1.73.4 | Integer32 | RO | |
scalar · Integer32 · read-only · current This object indicates the total number of LDP operational sessions. | ||||
| ThwLdpMultiLinkCfgTable | 1.3.6.1.4.1.2011.5.25.143.1.74 | NA | ||
table · not-accessible · current This object indicates that MPLS LDP multi-link (include local and remote coexist) configurations are inconsistent. The index of this entry is hwMplsLdpVrfIndex,hwMplsLdpPeerLdpId,hwMplsLdpLocalLdpId,hwMplsLdpConfigIfIndex, hwMplsLdpConfigRemotePeerIP and hwMplsLdpConfigType. | ||||
| RhwLdpMultiLinkCfgEntry | 1.3.6.1.4.1.2011.5.25.143.1.74.1 | NA | ||
row · not-accessible · current This object indicates that MPLS LDP multi-link (include local and remote coexist) configurations are inconsistent. The index of this entry is hwMplsLdpVrfIndex,hwMplsLdpPeerLdpId,hwMplsLdpLocalLdpId,hwMplsLdpConfigIfIndex, hwMplsLdpConfigRemotePeerIP and hwMplsLdpConfigType. | ||||
| ChwMplsLdpVrfIndex | 1.3.6.1.4.1.2011.5.25.143.1.74.1.1 | Integer32 | NA | |
column · Integer32 · not-accessible · current This object indicates the vrfIndex. | ||||
| ChwMplsLdpPeerLdpId | 1.3.6.1.4.1.2011.5.25.143.1.74.1.2 | MplsLdpIdentifier | NA | |
column · MplsLdpIdentifier · not-accessible · current This object indicates the peer LDP ID. | ||||
| ChwMplsLdpLocalLdpId | 1.3.6.1.4.1.2011.5.25.143.1.74.1.3 | MplsLdpIdentifier | NA | |
column · MplsLdpIdentifier · not-accessible · current This object indicates the local LDP ID. | ||||
| ChwMplsLdpConfigIfIndex | 1.3.6.1.4.1.2011.5.25.143.1.74.1.4 | Integer32 | NA | |
column · Integer32 · not-accessible · current This object indicates the inconsistent interface. | ||||
| ChwMplsLdpConfigRemotePeerIP | 1.3.6.1.4.1.2011.5.25.143.1.74.1.5 | InetAddress | NA | |
column · InetAddress · not-accessible · current This object indicates the rempte ip. Range: 1-32 characters | ||||
| ChwMplsLdpConfigType | 1.3.6.1.4.1.2011.5.25.143.1.74.1.6 | OCTET STRING | NA | |
column · OCTET STRING · not-accessible · current This object indicates the inconsistent configuration type. | ||||
| ChwMplsLdpConsistentState | 1.3.6.1.4.1.2011.5.25.143.1.74.1.7 | INTEGER | AN | |
column · INTEGER · accessible-for-notify · current This object indicates the the state is inconsistent or consistent.
| ||||
| ChwMplsLdpEffectKeepAlive | 1.3.6.1.4.1.2011.5.25.143.1.74.1.8 | Integer32 | AN | |
column · Integer32 · accessible-for-notify · current This object indicates the value of effect keepalive time. | ||||
| ChwMplsLdpEffectTransportAddr | 1.3.6.1.4.1.2011.5.25.143.1.74.1.9 | InetAddress | AN | |
column · InetAddress · accessible-for-notify · current This object indicates the value of effect transport address. | ||||
| ChwMplsLdpEffectLabelAdvertisementMode | 1.3.6.1.4.1.2011.5.25.143.1.74.1.10 | OCTET STRING | AN | |
column · OCTET STRING · accessible-for-notify · current This object indicates the value of effect label advertisement mode. | ||||
| ThwLdpPeerAddressTable | 1.3.6.1.4.1.2011.5.25.143.1.75 | NA | ||
table · not-accessible · current This object indicates that peer address count has exceeded the total count. The index of this entry is hwLdpPeerAddressLsrId and hwLdpPeerVrfIndex. | ||||
| RhwLdpPeerAddressEntry | 1.3.6.1.4.1.2011.5.25.143.1.75.1 | NA | ||
row · not-accessible · current This object indicates that peer address count has exceeded the total count. The index of this entry is hwLdpPeerAddressLsrId and hwLdpPeerVrfIndex. | ||||
| ChwLdpPeerAddressLsrId | 1.3.6.1.4.1.2011.5.25.143.1.75.1.1 | MplsLdpIdentifier | AN | |
column · MplsLdpIdentifier · accessible-for-notify · current This object indicates peer LSR ID. | ||||
| ChwLdpPeerVrfIndex | 1.3.6.1.4.1.2011.5.25.143.1.75.1.2 | Integer32 | AN | |
column · Integer32 · accessible-for-notify · current This object indicates the vrfIndex. | ||||
| ChwLdpAddressTotalCount | 1.3.6.1.4.1.2011.5.25.143.1.75.1.3 | Integer32 | AN | |
column · Integer32 · accessible-for-notify · current The value of this object identifies the maximum number of peer address. | ||||
| ThwLdpMappingTable | 1.3.6.1.4.1.2011.5.25.143.1.76 | NA | ||
table · not-accessible · current This object indicates that mapping count has exceeded the total count. The index of this entry is hwLdpMappingType and hwLdpVrfIndex. | ||||
| RhwLdpMappingEntry | 1.3.6.1.4.1.2011.5.25.143.1.76.1 | NA | ||
row · not-accessible · current This object indicates that mapping count has exceeded the total count. The index of this entry is hwLdpMappingType and hwLdpVrfIndex. | ||||
| ChwLdpMappingType | 1.3.6.1.4.1.2011.5.25.143.1.76.1.1 | OCTET STRING | AN | |
column · OCTET STRING · accessible-for-notify · current sent -Indicates that the sent mapping. received -Indicates that the received mapping. | ||||
| ChwLdpVrfIndex | 1.3.6.1.4.1.2011.5.25.143.1.76.1.2 | Integer32 | AN | |
column · Integer32 · accessible-for-notify · current This object indicates the vrfIndex. | ||||
| ChwLdpMappingTotalCount | 1.3.6.1.4.1.2011.5.25.143.1.76.1.3 | Integer32 | AN | |
column · Integer32 · accessible-for-notify · current The value of this object identifies the maximum number of mapping count. | ||||
| ThwLdpLastLocalAdjDownTable | 1.3.6.1.4.1.2011.5.25.143.1.77 | NA | ||
table · not-accessible · current This object indicates that the last local adjacency in the local-and-remote LDP session went Down due to hello timeout. The index of this entry is hwLdpVrfName, hwLdpAdjPeerLsrId. | ||||
| RhwLdpLastLocalAdjDownEntry | 1.3.6.1.4.1.2011.5.25.143.1.77.1 | NA | ||
row · not-accessible · current This object indicates that the last local adjacency in the local-and-remote LDP session went Down due to hello timeout. The index of this entry is hwLdpVrfName, hwLdpAdjPeerLsrId. | ||||
| ChwLdpVrfName | 1.3.6.1.4.1.2011.5.25.143.1.77.1.1 | OCTET STRING | AN | |
column · OCTET STRING · accessible-for-notify · current This object indicates the VRF name. | ||||
| ChwLdpAdjPeerLsrId | 1.3.6.1.4.1.2011.5.25.143.1.77.1.2 | MplsLdpIdentifier | AN | |
column · MplsLdpIdentifier · accessible-for-notify · current This object indicates the LSR ID of the LDP peer. | ||||
| ChwLdpInterfaceName | 1.3.6.1.4.1.2011.5.25.143.1.77.1.3 | OCTET STRING | AN | |
column · OCTET STRING · accessible-for-notify · current This object indicates the interface name. | ||||
| NhwMplsLdpTrap | 1.3.6.1.4.1.2011.5.25.143.2 | |||
| !hwMplsLdpSessionDown | 1.3.6.1.4.1.2011.5.25.143.2.1 | obsolete | ||
notification · obsolete When the trap indicating that a session is down is sent, the cause for the down LDP session is displayed. | ||||
| !hwMplsLdpLspDown | 1.3.6.1.4.1.2011.5.25.143.2.2 | obsolete | ||
notification · obsolete When the trap indicating that a session is down is sent, the cause for the down LSP session is displayed. | ||||
| !hwMplsLdpHostIngressLspDownClear | 1.3.6.1.4.1.2011.5.25.143.2.3 | |||
notification · current A trap is sent to clear the down trap of a specified FEC's ingress lsp.
| ||||
| !hwMplsLdpHostIngressLspDown | 1.3.6.1.4.1.2011.5.25.143.2.4 | |||
notification · current A trap is sent when all the ingress lsp of a specified FEC went down. | ||||
| !hwMplsLdpMultiLinkCfgInconsistent | 1.3.6.1.4.1.2011.5.25.143.2.5 | |||
notification · current Indicates that MPLS LDP multi-link configurations are Inconsistent. | ||||
| !hwMplsLdpMultiLinkCfgInconsistentClear | 1.3.6.1.4.1.2011.5.25.143.2.6 | |||
notification · current Indicates that MPLS LDP multi-link configurations are consistent. | ||||
| !hwMplsLdpPeerAddressCountExceed | 1.3.6.1.4.1.2011.5.25.143.2.7 | |||
notification · current Indicates that peer address count reaches the upper limit. | ||||
| !hwMplsLdpPeerAddressCountExceedClear | 1.3.6.1.4.1.2011.5.25.143.2.8 | |||
notification · current Indicates that peer address count falls from the upper limit. | ||||
| !hwMplsLdpMappingCountExceed | 1.3.6.1.4.1.2011.5.25.143.2.9 | |||
notification · current Indicates that the number of LDP label mapping sent or received on the device exceeded the upper limit. | ||||
| !hwMplsLdpMappingCountExceedClear | 1.3.6.1.4.1.2011.5.25.143.2.10 | |||
notification · current Indicates that the number of LDP label mapping sent or received on the device falls from the upper limit.
| ||||
| !hwMplsLdpLastLocalAdjDown | 1.3.6.1.4.1.2011.5.25.143.2.11 | |||
notification · current The last local adjacency in the local-and-remote LDP session went Down due to hello timeout. | ||||
| !hwMplsLdpLastLocalAdjDownClear | 1.3.6.1.4.1.2011.5.25.143.2.12 | |||
notification · current A local adjacency is established, and the alarm is cleared.
| ||||
| NhwMplsLdpConformance | 1.3.6.1.4.1.2011.5.25.143.3 | |||
| MhwMplsLdpCompliances | 1.3.6.1.4.1.2011.5.25.143.3.1 | |||
compliance · current The Compliance statement for systems supporting the HUAWEI-MPLSLDP-MIB.
| ||||
| NhwMplsLdpGroup | 1.3.6.1.4.1.2011.5.25.143.3.2 | |||
| GhwMplsLdpInfoGroup | 1.3.6.1.4.1.2011.5.25.143.3.2.1 | |||
group · current Infomation about LDP LSP.
| ||||
| GhwMplsLdpNotificationGroup | 1.3.6.1.4.1.2011.5.25.143.3.2.2 | obsolete | ||
| GhwMplsLdpLspDownNotificationGroup | 1.3.6.1.4.1.2011.5.25.143.3.2.3 | obsolete | ||
| GhwMplsLdpGlobalGroup | 1.3.6.1.4.1.2011.5.25.143.3.2.4 | |||
group · current Information about Ldp Global configuration.
| ||||
| GhwMplsLdpVpnGlobalGroup | 1.3.6.1.4.1.2011.5.25.143.3.2.5 | |||
group · current Information about Ldp Vpn configuration. | ||||
| GhwMplsLdpRemoteEntityGroup | 1.3.6.1.4.1.2011.5.25.143.3.2.6 | |||
group · current Information about remote entity.
| ||||
| GhwMplsLdpPeerGroup | 1.3.6.1.4.1.2011.5.25.143.3.2.7 | |||
group · current Information about Ldp Peer.
| ||||
| GhwMplsLdpVpnPeerGroup | 1.3.6.1.4.1.2011.5.25.143.3.2.8 | |||
group · current Information about Ldp Vpn Peer. | ||||
| GhwMplsLdpInterfaceGroup | 1.3.6.1.4.1.2011.5.25.143.3.2.9 | |||
group · current Information about Ldp interface capability. | ||||
| GhwLdpLspDownReasonGroup | 1.3.6.1.4.1.2011.5.25.143.3.2.10 | |||
group · current Information about Ldp ingress Lsp down reason. | ||||
| GhwMplsLdpHostIngressLspDownNotificationGroup | 1.3.6.1.4.1.2011.5.25.143.3.2.11 | |||
group · current Notification information included in the mib. | ||||
| GhwLdpPolicyPeerGroupGroup | 1.3.6.1.4.1.2011.5.25.143.3.2.15 | |||
group · current Information about Ldp Policies of peer groups. | ||||
| GhwMplsLdpFrrProtectGroup | 1.3.6.1.4.1.2011.5.25.143.3.2.16 | obsolete | ||
| GhwMplsLdpSessionStatisticsGroup | 1.3.6.1.4.1.2011.5.25.143.3.2.17 | |||
group · current Information about Ldp Session Statistics. | ||||
| GhwMplsLdpMultiLinkCfgGroup | 1.3.6.1.4.1.2011.5.25.143.3.2.18 | |||
group · current Information about MPLS LDP multi-link configurations. | ||||
| GhwMplsLdpMultiLinkCfgNotificationGroup | 1.3.6.1.4.1.2011.5.25.143.3.2.19 | |||
group · current Information about MPLS LDP multi-link configurations. | ||||
| GhwMplsLdpPeerAddressGroup | 1.3.6.1.4.1.2011.5.25.143.3.2.20 | |||
group · current Information about MPLS LDP peer address. | ||||
| GhwMplsLdpPeerAddressTotalCountNotificationGroup | 1.3.6.1.4.1.2011.5.25.143.3.2.21 | |||
group · current Information about MPLS LDP peer address notification. | ||||
| GhwMplsLdpMappingCountGroup | 1.3.6.1.4.1.2011.5.25.143.3.2.22 | |||
group · current Information about MPLS LDP mapping count. | ||||
| GhwMplsLdpMappingCountNotificationGroup | 1.3.6.1.4.1.2011.5.25.143.3.2.23 | |||
group · current Information about MPLS LDP mapping count notification. | ||||
| GhwMplsLdpLastLocalAdjDownGroup | 1.3.6.1.4.1.2011.5.25.143.3.2.24 | |||
group · current Information about MPLS LDP last local adjacency. | ||||
| GhwMplsLdpLastLocalAdjDownNotificationGroup | 1.3.6.1.4.1.2011.5.25.143.3.2.25 | |||
group · current Information about MPLS LDP last local adjacency notification. | ||||
Traps / Notifications
- hwMplsLdpHostIngressLspDown
1.3.6.1.4.1.2011.5.25.143.2.4 - hwMplsLdpHostIngressLspDownClear
1.3.6.1.4.1.2011.5.25.143.2.3 - hwMplsLdpLastLocalAdjDown
1.3.6.1.4.1.2011.5.25.143.2.11 - hwMplsLdpLastLocalAdjDownClear
1.3.6.1.4.1.2011.5.25.143.2.12 - hwMplsLdpLspDown
1.3.6.1.4.1.2011.5.25.143.2.2 - hwMplsLdpMappingCountExceed
1.3.6.1.4.1.2011.5.25.143.2.9 - hwMplsLdpMappingCountExceedClear
1.3.6.1.4.1.2011.5.25.143.2.10 - hwMplsLdpMultiLinkCfgInconsistent
1.3.6.1.4.1.2011.5.25.143.2.5 - hwMplsLdpMultiLinkCfgInconsistentClear
1.3.6.1.4.1.2011.5.25.143.2.6 - hwMplsLdpPeerAddressCountExceed
1.3.6.1.4.1.2011.5.25.143.2.7 - hwMplsLdpPeerAddressCountExceedClear
1.3.6.1.4.1.2011.5.25.143.2.8 - hwMplsLdpSessionDown
1.3.6.1.4.1.2011.5.25.143.2.1
Groups and compliance
- hwLdpLspDownReasonGroup
- hwLdpPolicyPeerGroupGroup
- hwMplsLdpCompliances
- hwMplsLdpFrrProtectGroup
- hwMplsLdpGlobalGroup
- hwMplsLdpHostIngressLspDownNotificationGroup
- hwMplsLdpInfoGroup
- hwMplsLdpInterfaceGroup
- hwMplsLdpLastLocalAdjDownGroup
- hwMplsLdpLastLocalAdjDownNotificationGroup
- hwMplsLdpLspDownNotificationGroup
- hwMplsLdpMappingCountGroup
- hwMplsLdpMappingCountNotificationGroup
- hwMplsLdpMultiLinkCfgGroup
- hwMplsLdpMultiLinkCfgNotificationGroup
- hwMplsLdpNotificationGroup
- hwMplsLdpPeerAddressGroup
- hwMplsLdpPeerAddressTotalCountNotificationGroup
- hwMplsLdpPeerGroup
- hwMplsLdpRemoteEntityGroup
- hwMplsLdpSessionStatisticsGroup
- hwMplsLdpVpnGlobalGroup
- hwMplsLdpVpnPeerGroup