HP-SN-SWITCH-GROUP-MIB
Hewlett-Packardsnmptranslate -m HP-SN-SWITCH-GROUP-MIB -Tpsnmpwalk -v2c -c <community> -m HP-SN-SWITCH-GROUP-MIB <host> 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1Imports
| HP-SN-ROOT-MIB | snSwitch |
|---|---|
| RFC1155-SMI | Counter32, Gauge32 |
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP |
| SNMPv2-SMI | Bits, Integer32, IpAddress, MODULE-IDENTITY, MibIdentifier, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, iso |
| SNMPv2-TC | DisplayString, PhysAddress, TEXTUAL-CONVENTION |
OID tree
| Name | OID | Type | Access | Status |
|---|---|---|---|---|
| NsnSwInfo | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1 | |||
| SsnSwGroupOperMode | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.1 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory noVLan(1) represents all switch ports with no virtual LAN by port (no Port VLAN), and with no tag assigned. vlanByPort(2) represents all switch ports with Basic VLAN (layer2 Switch).
| ||||
| SsnSwGroupIpL3SwMode | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.2 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory The Switch Group is configured with the Layer3 IP Switch mode either enabled or disabled and the default is disabled mode. enabled(1)...........activate Layer3 IP Switch disabled(0)..........disable Layer3 IP Switch
| ||||
| SsnSwGroupIpMcastMode | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.3 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory The Switch Group is configured with the IP Multicast pruning mode either enabled or disabled and the default is disabled mode. enabled(1)...........activate IP Multicast pruning disabled(0)..........no IP Multicast pruning
| ||||
| SsnSwGroupDefaultCfgMode | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.4 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory The Switch Group is configured with the Default configuration. If the default configuration gets overwritten, the state will change to non-default. default(1)...........default configuration nonDefault(2)..........non default configuration
| ||||
| SsnSwGroupSwitchAgeTime | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.5 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory The Switch Age time is 180sec by default. The configured range is 10 to 10,000sec. The time represents the time span to age out an MAC Address entry. | ||||
| SsnVLanGroupVlanCurEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.6 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory The current total entry number of VLANs are configured. | ||||
| SsnVLanGroupSetAllVLan | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.7 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory The value of this object is the VLanIndex of a particalur
entry in snVLanByPortTable (snVLanByPortVLanIndex).
All the attributes of that row of table except PortMask
will be used to set the same attributes for the
entire VLan group. VLanId and PortMask must be set for
that particular entry prior to setting this object.
Switch software will base on that VLAN information
to set the entire VLAN.
Note: All the intended attributes of the given
row of the table (given VLAN) must be set prior
setting this object. When this object is set,
Set-All-VLAN action will take place simultaneously.
The previous setting will be overwritten by the
new one. | ||||
| SsnSwPortSetAll | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.8 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory The value of this object is the index number of the snSwPortInfoTable (snSwPortInfoPortIndex). snSwPortInfoMonitorMode, snSwPortInfoTagMode, snSwPortInfoChnMode, snSwPortInfoSpeed, snSwPortInfoAdminStatus are all the read-write attributes of that row of table. They will be used to set the same attributes for all the ports in the system. Note: prior setting this object, all the intended attributes of the given row of the table must be set. Otherwise, the current data of the row will be used to set the entire port-table. The previous setting will be overwritten by the new one. | ||||
| SsnFdbTableCurEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.9 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory The current total entry number of FDB are configured. | ||||
| SsnFdbTableStationFlush | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.10 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory The following values of the flush state can only be read: normal(1)... normal state error(2)... operation failed flushing(4)... in process The following value can be written: flush(3).....do flush The agent will return a response even before the flush is done. And the read value will be flushing until flush is done. And the flush request will be rejected until error or normal.
| ||||
| SsnPortStpSetAll | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.11 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory The value of this object is 1 which means invoking
Port STP Set-all command. The snPortStpPriority,
snPortStpPathCost, the read-write STP related
attributes of the first row of table will be used
to set the same attributes for all the ports in the
system.
Note: prior setting this object, all the intended
attributes of the given row of the table must be set.
Otherwise, the current data of the row will be used to
set the entire port-table. The previous setting will
be overwritten by the new one. | ||||
| SsnSwProbePortNum | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.12 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory A chassis switch probe port is operated as a traffic analyzer port and only one port can be assigned in the chassis. The bit 0 to bit 7: port number. The bit 8 to bit 11: slot number. A stackable switch is only assigned with one probe port as a traffic analyzer. | ||||
| SsnSw8021qTagMode | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.13 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory The Switch Group is configured with the IEEE802.1q Tagging mode either enabled or disabled and the default is disabled mode. enabled(1)...........activate IEEE802.1q Tagging mode. disabled(0)..........no IEEE802.1q Tagging.
| ||||
| SsnSwGlobalStpMode | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.14 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Spanning Tree System Global Mode in the Switch Group can be set either enabled or disabled and the default is enabled mode. enabled(1)...........activate Spanning Tree disabled(0)..........no Spanning Tree
| ||||
| SsnSwIpMcastQuerierMode | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.15 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory The IP Multicast pruning mode is configured either
Non-Querier or Querier mode and the default is
querier mode.
querier(1)...........when prunning traffic locally
within the VLAN.
nonQuerier(2)........when running with a multicast
capable router in the network.
| ||||
| SsnSwViolatorPortNumber | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.17 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory The port number of the switch or router that received a violator packet. It is included in the locked address violation trap. The bit 0 to bit 7: port number. The bit 8 to bit 11: slot number (slot for chassis only). | ||||
| SsnSwViolatorMacAddress | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.18 | MacAddress | RO | mandatory |
scalar · MacAddress · read-only · mandatory The source address of the violator packet received by the switch or router. It is included in the locked address violation trap. | ||||
| SsnVLanGroupVlanMaxEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.19 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory The maximum number of VLAN entries are allowed to configure. | ||||
| SsnSwEosBufferSize | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.20 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory A specific buffer size for all the different EOS buffers. | ||||
| SsnVLanByPortEntrySize | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.21 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory The size of each VLAN table entry. | ||||
| SsnSwPortEntrySize | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.22 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory The size of each port table entry. | ||||
| SsnFdbStationEntrySize | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.23 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory The size of each Fdb station table entry. | ||||
| SsnPortStpEntrySize | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.24 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory The size of each port stp table entry. | ||||
| SsnSwEnableBridgeNewRootTrap | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.25 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Indicates whether the SNMP agent process is permitted to generate bridge new root traps.
| ||||
| SsnSwEnableBridgeTopoChangeTrap | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.26 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Indicates whether the SNMP agent process is permitted to generate bridge topology change traps.
| ||||
| SsnSwEnableLockedAddrViolationTrap | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.27 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Indicates whether the SNMP agent process is permitted to generate locked address violation traps.
| ||||
| SsnSwIpxL3SwMode | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.28 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory The Switch Group is configured with the Layer3 IPX Switch mode either enabled or disabled and the default is disabled mode. enabled(1)...........activate Layer3 Switch disabled(0)..........disable Layer3 Switch
| ||||
| SsnVLanByIpSubnetMaxSubnets | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.29 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory The maximum number of subnets for each IP VLAN. | ||||
| SsnVLanByIpxNetMaxNetworks | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.30 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory The maximum number of networks for each IPX VLAN. | ||||
| SsnSwProtocolVLanMode | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.31 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory disabled(0) - represents system with Protocol VLAN disabled. enabled(1) - represents system with Protocol VLAN enabled (Layer3 VLAN).
| ||||
| SsnMacStationVLanId | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.32 | INTEGER (1..4095) | RW | mandatory |
scalar · INTEGER (1..4095) · read-write · mandatory This MAC Station VLAN ID index to the standard Forwarding Database for Transparent Bridge Table. (dot1dTpFdbTable). Since the dot1dTpFdbTable index is the MAC Address assigned to one of the ports in the bridge(VLAN) and each MAC address can be re-assigned to a different ports belonging to different bridges(VLANs), the snMacStationVLanId can be used by users to specify which bridge(VLAN) MAC Station information of the dot1dTpFdbTable users want to retrieve. If users do not specify the VLan ID in this MIB, the default VLAN (bridge) ID will be used when dot1dTpFdbTable is retrieved. | ||||
| SsnSwClearCounters | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.33 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory valid(0) - a SNMP-GET of this mib shows that it is valid command to use. clear(1) - represents clear counter command of the following counters: Dot3, MIB2, IP and IPX counters for all ports.
| ||||
| SsnSw8021qTagType | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.34 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory The IEEE802.1q tag type embedded in the length/type field of an Ethernet packet. It specifies that the 2 octets after the length/type field in an Ethernet packet is the tag value. | ||||
| SsnSwBroadcastLimit | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.35 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Limit the number of broadcast packets to forward out of the switch ports. This object specifies the number of broadcast packets per second. Setting a value of 0 to this object disables the limitation check. | ||||
| SsnSwMaxMacFilterPerSystem | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.36 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory The maximum number of MAC Filters per system in the MAC Filter table. | ||||
| SsnSwMaxMacFilterPerPort | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.37 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory The maximum number of MAC Filters per port in the Port MAC Access Filter table. | ||||
| SsnSwDefaultVLanId | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.38 | INTEGER (1..4095) | RW | mandatory |
scalar · INTEGER (1..4095) · read-write · mandatory The VLAN ID of the DEFAULT PORT-VLAN. | ||||
| SsnSwGlobalAutoNegotiate | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.39 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory This feature only applies to Gigabit Ethernet ports. If set to disable(0), all Gigabit Ethernet ports will be put to non- negotiation mode. If set to enable(1), all Gigabit Ethernet ports will start auto-negotiation indefinitely until succeed. If set to negFullAuto(2), all Gigabit Ethernet ports will start with auto-negotiation, if the negotiation failed, then they will automatically switch to non-negotiation mode. Stackable products (except TurboIron 8) Gigabit Ethernet ports do not support negFullAuto(2). If the snSwPortInfoAutoNegotiate value of a port was not set to global, this global value does not apply to the negotiation mode of that port.
| ||||
| SsnSwQosMechanism | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.40 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Indicates whether the qos mechanism is strict or weighted.
| ||||
| SsnSwSingleStpMode | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.41 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Single Spanning Tree System Mode in the Switch Group can be set either enabled or disabled and the default is disabled mode. enabled(1)...........activate Single Spanning Tree disabled(0)..........no Single Spanning Tree
| ||||
| SsnSwFastStpMode | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.1.42 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Fast Spanning Tree System Mode in the Switch Group can be set either enabled or disabled and the default is enabled mode. enabled(1)...........activate Fast Spanning Tree disabled(0)..........no Fast Spanning Tree
| ||||
| NsnVLanInfo | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2 | |||
| TsnVLanByPortTable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1 | NA | deprecated | |
table · not-accessible · deprecated If snSwGroupOperMode is configured as basic mode which is VLAN by Port, Layer2 switching, then this table is valid. Each VLAN switch port could have a number of VLAN IDs. | ||||
| RsnVLanByPortEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1 | NA | deprecated | |
row · not-accessible · deprecated An entry in the VLAN By Port Information table. snVLanByPortVLanIndex = 1 and with snVLanByPortVLanId = 1 together implies all attributes applying to the Global switch group i.e. noVLan. A SNMP SET PDU for a row of the snVLanByPortTable requires the entired sequence of the MIB Objects in each snVLanByPortEntry stored in one PDU. Otherwise, GENERR return-value will be returned. | ||||
| CsnVLanByPortVLanIndex | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.1 | INTEGER (1..4095) | RO | deprecated |
column · INTEGER (1..4095) · read-only · deprecated The VLAN ID index must not be greater than the snVLanGroupVlanMaxEntry. Each VLAN Identifier can have a membership of multiple ports. | ||||
| CsnVLanByPortVLanId | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.2 | INTEGER (1..4095) | RW | deprecated |
column · INTEGER (1..4095) · read-write · deprecated The VLAN ID index to the VLAN By Port Info Table. Each VLAN Identifier can have a membership of multiple ports. | ||||
| CsnVLanByPortPortMask | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.3 | PortMask | RW | deprecated |
column · PortMask · read-write · deprecated The Standand-alone switch VLAN port membership. (It was obsoleted for Chassis Product) | ||||
| CsnVLanByPortQos | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.4 | INTEGER | RW | deprecated |
column · INTEGER · read-write · deprecated The Stand alone stackable switch VLAN Priority values are: low(0) -- low prority high(1) -- high prority. The BigIron switch VLAN Priority values are: level0(0), level1(1), level2(2), level3(3), level4(4), level5(5), level6(6), level7(7)
| ||||
| CsnVLanByPortStpMode | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.5 | INTEGER | RW | deprecated |
column · INTEGER · read-write · deprecated Spanning Tree Mode in the Switch Group can be set either enabled or disabled and the default is enabled mode. enabled(1)...........activate Spanning Tree disabled(0)..........no Spanning Tree
| ||||
| CsnVLanByPortStpPriority | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.6 | INTEGER (1..65535) | RW | deprecated |
column · INTEGER (1..65535) · read-write · deprecated dot1dStpPriority : The value of the write-able portion of the Stp ID, i.e., the first two octets of the (8 octet long) Bridge ID. The other (last) 6 octets of the Bridge ID are given by the value of the base bridge address - dot1dBaseBridgeAddress. | ||||
| CsnVLanByPortStpGroupMaxAge | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.7 | INTEGER (6..40) | RW | deprecated |
column · INTEGER (6..40) · read-write · deprecated dot1dStpBridgeMaxAge: From RFC1493(Bridge MIB). The value that all bridges use for MaxAge when this bridge is acting as the root. Note that 802.1D-1990 specifies that the range for this parameter is related to the value of dot1dStpBridgeHelloTime. The granularity of this timer is specified by 802.1D-1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds. | ||||
| CsnVLanByPortStpGroupHelloTime | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.8 | INTEGER (1..10) | RW | deprecated |
column · INTEGER (1..10) · read-write · deprecated dot1dStpBridgeHelloTime: From RFC1493(Bridge MIB). The value that all bridges use for HelloTime when this bridge is acting as the root. The granularity of this timer is specified by 802.1D- 1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds. | ||||
| CsnVLanByPortStpGroupForwardDelay | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.9 | INTEGER (2..30) | RW | deprecated |
column · INTEGER (2..30) · read-write · deprecated dot1dStpBridgeForwardDelay : From RFC1493(Bridge MIB). The value that all bridges use for ForwardDelay when this bridge is acting as the root. Note that 802.1D-1990 specifies that the range for this parameter is related to the value of dot1dStpBridgeMaxAge. The granularity of this timer is specified by 802.1D-1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds. | ||||
| CsnVLanByPortRowStatus | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.10 | INTEGER | RW | deprecated |
column · INTEGER · read-write · deprecated This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row other(1)....some other case valid(2)....the row exists and is valid
| ||||
| CsnVLanByPortOperState | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.11 | INTEGER | RO | deprecated |
column · INTEGER · read-only · deprecated By default, this mode is set to notActivated(0). notActivated(0)...the VLAN entry is not activated and not in running mode. activated(1)......the VLAN entry is activated and in running mode
| ||||
| CsnVLanByPortBaseNumPorts | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.12 | INTEGER | RO | deprecated |
column · INTEGER · read-only · deprecated The number of ports controlled by this bridging entity. | ||||
| CsnVLanByPortBaseType | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.13 | INTEGER | RO | deprecated |
column · INTEGER · read-only · deprecated Indicates what type of bridging this bridge can perform. If a bridge is actually performing a certain type of bridging this will be indicated by entries in the port table for the given type.
| ||||
| CsnVLanByPortStpProtocolSpecification | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.14 | INTEGER | RO | deprecated |
column · INTEGER · read-only · deprecated An indication of what version of the Spanning Tree Protocol is being run. The value 'decLb100(2)' indicates the DEC LANbridge 100 Spanning Tree protocol. IEEE 802.1d implementations will return 'ieee8021d(3)'. If future versions of the IEEE Spanning Tree Protocol are released that are incompatible with the current version a new value will be defined.
| ||||
| CsnVLanByPortStpMaxAge | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.15 | Timeout | RO | deprecated |
column · Timeout · read-only · deprecated dot1dStpMaxAge: From RFC1493(Bridge MIB). The maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded, in units of hundredths of a second. This is the actual value that this bridge is currently using. | ||||
| CsnVLanByPortStpHelloTime | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.16 | Timeout | RO | deprecated |
column · Timeout · read-only · deprecated dot1dStpHelloTime: From RFC1493(Bridge MIB). The amount of time between the transmission of Configuration bridge PDUs by this node on any port when it is the root of the spanning tree or trying to become so, in units of hundredths of a second. This is the actual value that this bridge is currently using. | ||||
| CsnVLanByPortStpHoldTime | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.17 | INTEGER | RO | deprecated |
column · INTEGER · read-only · deprecated dot1dStpHoldTime: From RFC1493(Bridge MIB). This time value determines the interval length during which no more than two Configuration bridge PDUs shall be transmitted by this node, in units of hundredths of a second. | ||||
| CsnVLanByPortStpForwardDelay | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.18 | Timeout | RO | deprecated |
column · Timeout · read-only · deprecated dot1dStpForwardDelay: From RFC1493(Bridge MIB). This time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the Forwarding state. The value determines how long the port stays in each of the Listening and Learning states, which precede the Forwarding state. This value is also used, when a topology change has been detected and is underway, to age all dynamic entries in the Forwarding Database. [Note that this value is the one that this bridge is currently using, in contrast to dot1dStpBridgeForwardDelay which is the value that this bridge and all others would start using if/when this bridge were to become the root.] | ||||
| CsnVLanByPortStpTimeSinceTopologyChange | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.19 | TimeTicks | RO | deprecated |
column · TimeTicks · read-only · deprecated The time (in hundredths of a second) since the last time a topology change was detected by the bridge entity. | ||||
| CsnVLanByPortStpTopChanges | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.20 | Counter32 | RO | deprecated |
column · Counter32 · read-only · deprecated The total number of topology changes detected by this bridge since the management entity was last reset or initialized. | ||||
| CsnVLanByPortStpRootCost | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.21 | INTEGER | RO | deprecated |
column · INTEGER · read-only · deprecated dot1dStpRootCost: From RFC1493(Bridge MIB). The cost of the path to the root as seen from this bridge. | ||||
| CsnVLanByPortStpRootPort | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.22 | INTEGER | RO | deprecated |
column · INTEGER · read-only · deprecated dot1dStpRootPort: From RFC1493(Bridge MIB). The port number of the port which offers the lowest cost path from this bridge to the root bridge. | ||||
| CsnVLanByPortStpDesignatedRoot | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.23 | BridgeId | RO | deprecated |
column · BridgeId · read-only · deprecated dot1dStpDesignatedRoot: From RFC1493(Bridge MIB). The bridge identifier of the root of the spanning tree as determined by the Spanning Tree Protocol as executed by this node. This value is used as the Root Identifier parameter in all Configuration Bridge PDUs originated by this node. | ||||
| CsnVLanByPortBaseBridgeAddress | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.24 | MacAddress | RO | deprecated |
column · MacAddress · read-only · deprecated The MAC address used by this bridge when it must be referred to in a unique fashion. It is recommended that this be the numerically smallest MAC address of all ports that belong to this bridge. However it is only required to be unique. When concatenated with dot1dStpPriority a unique BridgeIdentifier is formed which is used in the Spanning Tree Protocol. | ||||
| CsnVLanByPortVLanName | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.25 | DisplayString (SIZE (0..32)) | RW | deprecated |
column · DisplayString (SIZE (0..32)) · read-write · deprecated VLAN Community Name string. | ||||
| CsnVLanByPortRouterIntf | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.26 | INTEGER (1..60) | RW | deprecated |
column · INTEGER (1..60) · read-write · deprecated Optional: A virtual interface for router to the VLAN -- applied to router only. If a SNMP-Get value is zero, that means this object was not configured. | ||||
| CsnVLanByPortChassisPortMask | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.27 | OCTET STRING (SIZE (32)) | RW | deprecated |
column · OCTET STRING (SIZE (32)) · read-write · deprecated The Chassis VLAN switch port membership. (It was obsoleted after release 07100, replaced by snVLanByPortPortList) | ||||
| CsnVLanByPortPortList | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.1.1.28 | OCTET STRING | RW | deprecated |
column · OCTET STRING · read-write · deprecated A list of port indices which are the port membership of a VLAN By Port. Each port index is a 16-bit integer in big endian order. 8-bit is the slot number, the other 8-bit is the port number. | ||||
| TsnVLanByProtocolTable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.2 | NA | mandatory | |
table · not-accessible · mandatory . | ||||
| RsnVLanByProtocolEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.2.1 | NA | mandatory | |
row · not-accessible · mandatory An entry in the VLAN By Protocol Configuration table. | ||||
| CsnVLanByProtocolVLanId | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.2.1.1 | INTEGER (1..4095) | RO | mandatory |
column · INTEGER (1..4095) · read-only · mandatory The VLAN ID index to both of the VLAN By Port Info Table and this table. | ||||
| CsnVLanByProtocolIndex | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.2.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The following IP/IPX protocol VLAN types are operated in Layer3 VLAN such as : ip(1), ipx(2), ipv6(7) The following are operated in Layer2 bridging such as: appleTalk(3), decNet(4), netBios(5), others(6) -- other protocols which are defined here.
| ||||
| CsnVLanByProtocolDynamic | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.2.1.3 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory disabled(0) : disabled dynamic port inclusion - applied to switch only. enabled(1) : enabled dynamic port inclusion - applied to switch only.
| ||||
| CsnVLanByProtocolStaticMask | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.2.1.4 | PortMask | RW | deprecated |
column · PortMask · read-write · deprecated The Standand-alone switch Protocol VLAN port membership applied in static mode. (It was obsoleted for Chassis Product) | ||||
| CsnVLanByProtocolExcludeMask | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.2.1.5 | PortMask | RW | deprecated |
column · PortMask · read-write · deprecated The Standand-alone switch Protocol VLAN port membership applied in exclusive mode. (It was obsoleted for Chassis Product) | ||||
| CsnVLanByProtocolRouterIntf | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.2.1.6 | INTEGER (1..60) | RW | mandatory |
column · INTEGER (1..60) · read-write · mandatory Optional: A virtual interface for router to the VLAN -- applied to router only. If a SNMP-Get value is zero, that means this object was not configured. | ||||
| CsnVLanByProtocolRowStatus | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.2.1.7 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row other(1)....some other case valid(2)....the row exists and is valid
| ||||
| CsnVLanByProtocolDynamicMask | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.2.1.8 | PortMask | RO | deprecated |
column · PortMask · read-only · deprecated The Standand-alone switch Protocol VLAN active port membership. (It was obsoleted for Chassis Product) | ||||
| CsnVLanByProtocolChassisStaticMask | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.2.1.9 | OCTET STRING (SIZE (32)) | RW | deprecated |
column · OCTET STRING (SIZE (32)) · read-write · deprecated The Chassis Protocol VLAN port membership applied in static mode. (It was obsoleted after release 07100, replaced by snVLanByProtocolStaticPortList) | ||||
| CsnVLanByProtocolChassisExcludeMask | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.2.1.10 | OCTET STRING (SIZE (32)) | RW | deprecated |
column · OCTET STRING (SIZE (32)) · read-write · deprecated The Chassis Protocol VLAN port membership applied in exclusive mode. (It was obsoleted after release 07100, replaced by snVLanByProtocolExcludePortList) | ||||
| CsnVLanByProtocolChassisDynamicMask | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.2.1.11 | OCTET STRING (SIZE (32)) | RO | deprecated |
column · OCTET STRING (SIZE (32)) · read-only · deprecated The Chassis Protocol VLAN active port membership. (It was obsoleted after release 07100, replaced by snVLanByProtocolDynamicPortList) | ||||
| CsnVLanByProtocolVLanName | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.2.1.12 | DisplayString (SIZE (0..32)) | RW | mandatory |
column · DisplayString (SIZE (0..32)) · read-write · mandatory VLAN Community Name string. | ||||
| CsnVLanByProtocolStaticPortList | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.2.1.13 | OCTET STRING | RW | mandatory |
column · OCTET STRING · read-write · mandatory A list of port indices which are the configured port membership of the Protocol VLAN. Each port index is a 16-bit integer in big endian order. 8-bit is the slot number, the other 8-bit is the port number. | ||||
| CsnVLanByProtocolExcludePortList | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.2.1.14 | OCTET STRING | RW | mandatory |
column · OCTET STRING · read-write · mandatory A list of port indices which are the excluded from port membership of the Protocol VLAN. Each port index is a 16-bit integer in big endian order. 8-bit is the slot number, the other 8-bit is the port number. | ||||
| CsnVLanByProtocolDynamicPortList | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.2.1.15 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory A list of port indices which are dynamically joining the port membership of the Protocol VLAN. Each port index is a 16-bit integer in big endian order. 8-bit is the slot number, the other 8-bit is the port number. | ||||
| TsnVLanByIpSubnetTable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.3 | NA | mandatory | |
table · not-accessible · mandatory An entry of the VLAN By IPX Network Number Table. | ||||
| RsnVLanByIpSubnetEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.3.1 | NA | mandatory | |
row · not-accessible · mandatory An entry in the VLAN By IP Subnet Configuration table. | ||||
| CsnVLanByIpSubnetVLanId | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.3.1.1 | INTEGER (1..4095) | RO | mandatory |
column · INTEGER (1..4095) · read-only · mandatory The VLAN ID index to both of the VLAN By Port Info Table and this table. | ||||
| CsnVLanByIpSubnetIpAddress | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.3.1.2 | IpAddress | RO | mandatory |
column · IpAddress · read-only · mandatory Subnet IP address. | ||||
| CsnVLanByIpSubnetSubnetMask | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.3.1.3 | IpAddress | RO | mandatory |
column · IpAddress · read-only · mandatory Subnet mask associated with the Subnet IP address. | ||||
| CsnVLanByIpSubnetDynamic | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.3.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory disabled(0) : disabled dynamic port inclusion - applied to switch only. enabled(1) : enabled dynamic port inclusion - applied to switch only.
| ||||
| CsnVLanByIpSubnetStaticMask | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.3.1.5 | PortMask | RW | deprecated |
column · PortMask · read-write · deprecated The Standand-alone switch VLAN By Subnet port membership applied in static mode. (It was obsoleted for Chassis Product) | ||||
| CsnVLanByIpSubnetExcludeMask | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.3.1.6 | PortMask | RW | deprecated |
column · PortMask · read-write · deprecated The Standand-alone switch VLAN By Subnet port membership applied in exclusive mode. (It was obsoleted for Chassis Product) | ||||
| CsnVLanByIpSubnetRouterIntf | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.3.1.7 | INTEGER (1..60) | RW | mandatory |
column · INTEGER (1..60) · read-write · mandatory Optional: A virtual interface for router to the VLAN -- applied to router only. If a SNMP-Get value is zero, that means this object was not configured. | ||||
| CsnVLanByIpSubnetRowStatus | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.3.1.8 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row other(1)....some other case valid(2)....the row exists and is valid
| ||||
| CsnVLanByIpSubnetDynamicMask | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.3.1.9 | PortMask | RO | deprecated |
column · PortMask · read-only · deprecated The Standand-alone switch VLAN By Subnet active port membership. (It was obsoleted for Chassis Product) | ||||
| CsnVLanByIpSubnetChassisStaticMask | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.3.1.10 | OCTET STRING (SIZE (32)) | RW | deprecated |
column · OCTET STRING (SIZE (32)) · read-write · deprecated The Chassis VLAN By Subnet port membership applied in static mode. (It was obsoleted after release 07100, replaced by snVLanByIpSubnetStaticPortList) | ||||
| CsnVLanByIpSubnetChassisExcludeMask | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.3.1.11 | OCTET STRING (SIZE (32)) | RW | deprecated |
column · OCTET STRING (SIZE (32)) · read-write · deprecated The Chassis VLAN By Subnet port membership applied in exclusive mode. (It was obsoleted after release 07100, replaced by snVLanByIpSubnetExcludePortList) | ||||
| CsnVLanByIpSubnetChassisDynamicMask | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.3.1.12 | OCTET STRING (SIZE (32)) | RO | deprecated |
column · OCTET STRING (SIZE (32)) · read-only · deprecated The Chassis VLAN By Subnet active port membership. (It was obsoleted after release 07100, replaced by snVLanByIpSubnetDynamicPortList) | ||||
| CsnVLanByIpSubnetVLanName | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.3.1.13 | DisplayString (SIZE (0..32)) | RW | mandatory |
column · DisplayString (SIZE (0..32)) · read-write · mandatory VLAN Community Name string. | ||||
| CsnVLanByIpSubnetStaticPortList | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.3.1.14 | OCTET STRING | RW | mandatory |
column · OCTET STRING · read-write · mandatory A list of port indices which are the configured port membership of the VLAN By IP Subnet. Each port index is a 16-bit integer in big endian order. 8-bit is the slot number, the other 8-bit is the port number. | ||||
| CsnVLanByIpSubnetExcludePortList | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.3.1.15 | OCTET STRING | RW | mandatory |
column · OCTET STRING · read-write · mandatory A list of port indices which are the excluded from port membership of the VLAN By IP Subnet. Each port index is a 16-bit integer in big endian order. 8-bit is the slot number, the other 8-bit is the port number. | ||||
| CsnVLanByIpSubnetDynamicPortList | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.3.1.16 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory A list of port indices which are dynamically joining the port membership of the VLAN By IP Subnet. Each port index is a 16-bit integer in big endian order. 8-bit is the slot number, the other 8-bit is the port number. | ||||
| TsnVLanByIpxNetTable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.4 | NA | mandatory | |
table · not-accessible · mandatory An entry of the VLAN By IPX Network Number Table. | ||||
| RsnVLanByIpxNetEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.4.1 | NA | mandatory | |
row · not-accessible · mandatory An entry in the VLAN By Ipx Network Number Configuration table. | ||||
| CsnVLanByIpxNetVLanId | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.4.1.1 | INTEGER (1..4095) | RO | mandatory |
column · INTEGER (1..4095) · read-only · mandatory The VLAN ID index to both of the VLAN By Port Info Table and this table. | ||||
| CsnVLanByIpxNetNetworkNum | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.4.1.2 | OCTET STRING (SIZE (4)) | RO | mandatory |
column · OCTET STRING (SIZE (4)) · read-only · mandatory IPX Network Number. | ||||
| CsnVLanByIpxNetFrameType | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.4.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The following IPX Frame types are operated in Layer3 VLAN such as : ipxEthernet8022(1), ipxEthernet8023(2), ipxEthernetII(3), ipxEthernetSnap(4). choose notApplicable(0) for other protocols. Note: Each Network Number can be assigned with one unique Frame type; Otherwise, a SNMP-SET error will be returned.
| ||||
| CsnVLanByIpxNetDynamic | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.4.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory disabled(0) : disabled dynamic port inclusion - applied to switch only. enabled(1) : enabled dynamic port inclusion - applied to switch only.
| ||||
| CsnVLanByIpxNetStaticMask | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.4.1.5 | PortMask | RW | deprecated |
column · PortMask · read-write · deprecated The VLAN By IPX network port membership applied in static mode. (It was obsoleted for Chassis Product) | ||||
| CsnVLanByIpxNetExcludeMask | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.4.1.6 | PortMask | RW | deprecated |
column · PortMask · read-write · deprecated The VLAN By IPX network port membership applied in exclusive mode. (It was obsoleted for Chassis Product) | ||||
| CsnVLanByIpxNetRouterIntf | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.4.1.7 | INTEGER (1..60) | RW | mandatory |
column · INTEGER (1..60) · read-write · mandatory Optional: A virtual interface for router to the VLAN -- applied to router only. If a SNMP-Get value is zero, that means this object was not configured. | ||||
| CsnVLanByIpxNetRowStatus | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.4.1.8 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row other(1)....some other case valid(2)....the row exists and is valid
| ||||
| CsnVLanByIpxNetDynamicMask | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.4.1.9 | PortMask | RO | deprecated |
column · PortMask · read-only · deprecated The VLAN By IPX network active port membership. (It was obsoleted for Chassis Product) | ||||
| CsnVLanByIpxNetChassisStaticMask | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.4.1.10 | OCTET STRING (SIZE (32)) | RW | deprecated |
column · OCTET STRING (SIZE (32)) · read-write · deprecated The Chassis VLAN By IPX network port membership applied in static mode. (It was obsoleted after release 07100, replaced by snVLanByIpxNetStaticPortList) | ||||
| CsnVLanByIpxNetChassisExcludeMask | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.4.1.11 | OCTET STRING (SIZE (32)) | RW | deprecated |
column · OCTET STRING (SIZE (32)) · read-write · deprecated The Chassis VLAN By IPX network port membership applied in exclusive mode. (It was obsoleted after release 07100, replaced by snVLanByIpxNetExcludePortList) | ||||
| CsnVLanByIpxNetChassisDynamicMask | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.4.1.12 | OCTET STRING (SIZE (32)) | RO | deprecated |
column · OCTET STRING (SIZE (32)) · read-only · deprecated The Chassis VLAN By IPX network active port membership. (It was obsoleted after release 07100, replaced by snVLanByIpxNetDynamicPortList) | ||||
| CsnVLanByIpxNetVLanName | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.4.1.13 | DisplayString (SIZE (0..32)) | RW | mandatory |
column · DisplayString (SIZE (0..32)) · read-write · mandatory VLAN Community Name string. | ||||
| CsnVLanByIpxNetStaticPortList | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.4.1.14 | OCTET STRING | RW | mandatory |
column · OCTET STRING · read-write · mandatory A list of port indices which are the configured port membership of the VLAN By IPX network. Each port index is a 16-bit integer in big endian order. 8-bit is the slot number, the other 8-bit is the port number. | ||||
| CsnVLanByIpxNetExcludePortList | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.4.1.15 | OCTET STRING | RW | mandatory |
column · OCTET STRING · read-write · mandatory A list of port indices which are the excluded from port membership of the VLAN By IPX network. Each port index is a 16-bit integer in big endian order. 8-bit is the slot number, the other 8-bit is the port number. | ||||
| CsnVLanByIpxNetDynamicPortList | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.4.1.16 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory A list of port indices which are dynamically joining the port membership of the VLAN By IPX network. Each port index is a 16-bit integer in big endian order. 8-bit is the slot number, the other 8-bit is the port number. | ||||
| TsnVLanByATCableTable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.5 | NA | mandatory | |
table · not-accessible · mandatory A Table Of VLAN By AppleTalk Network Number. | ||||
| RsnVLanByATCableEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.5.1 | NA | mandatory | |
row · not-accessible · mandatory An entry of the AppleTalk Cable VLAN table. | ||||
| CsnVLanByATCableVLanId | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.5.1.1 | INTEGER (1..4095) | RO | mandatory |
column · INTEGER (1..4095) · read-only · mandatory The VLAN ID of a PORT VLAN of which the AppleTalk Cable VLAN was attaching to. | ||||
| CsnVLanByATCableIndex | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.5.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory AppleTalk Cable VLAN index number. | ||||
| CsnVLanByATCableRouterIntf | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.5.1.3 | INTEGER (0..60) | RW | mandatory |
column · INTEGER (0..60) · read-write · mandatory A virtual router interface to the AppleTalk Cable VLAN, only router products accept the SNMP-SET operation. The value zero indicates that virtual router interface was not configured. | ||||
| CsnVLanByATCableRowStatus | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.5.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row other(1)....some other case valid(2)....the row exists and is valid
| ||||
| CsnVLanByATCableChassisStaticMask | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.5.1.5 | OCTET STRING (SIZE (32)) | RW | deprecated |
column · OCTET STRING (SIZE (32)) · read-write · deprecated A list of ports which are statically configured to become port members of a VLAN. (It was obsoleted after release 07100, replaced by snVLanByATCableStaticPortList) | ||||
| CsnVLanByATCableVLanName | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.5.1.6 | DisplayString (SIZE (0..32)) | RW | mandatory |
column · DisplayString (SIZE (0..32)) · read-write · mandatory VLAN Name string. | ||||
| CsnVLanByATCableStaticPortList | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.5.1.7 | OCTET STRING | RW | mandatory |
column · OCTET STRING · read-write · mandatory A list of port indices which are the configured port membership of the AppleTalk Cable VLAN. Each port index is a 16-bit integer in big endian order. 8-bit is the slot number, the other 8-bit is the port number. | ||||
| TsnVLanByPortMemberTable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.6 | NA | mandatory | |
table · not-accessible · mandatory Port VLAN (Layer 2 VLAN) port membership table. | ||||
| RsnVLanByPortMemberEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.6.1 | NA | mandatory | |
row · not-accessible · mandatory An entry of the port VLAN membership table. | ||||
| CsnVLanByPortMemberVLanId | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.6.1.1 | INTEGER (1..4095) | RO | mandatory |
column · INTEGER (1..4095) · read-only · mandatory The VLAN identifier (VLAN ID). | ||||
| CsnVLanByPortMemberPortId | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.6.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The ifIndex which is a member of the port VLAN. | ||||
| CsnVLanByPortMemberRowStatus | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.6.1.3 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row other(1)....some other case valid(2)....the row exists and is valid
| ||||
| TsnVLanByPortCfgTable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.7 | NA | mandatory | |
table · not-accessible · mandatory Port VLAN (Layer 2 VLAN) configuration table. | ||||
| RsnVLanByPortCfgEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.7.1 | NA | mandatory | |
row · not-accessible · mandatory An entry of the port VLAN configuration table. | ||||
| CsnVLanByPortCfgVLanId | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.7.1.1 | INTEGER (1..4095) | RO | mandatory |
column · INTEGER (1..4095) · read-only · mandatory The VLAN identifier (VLAN ID). | ||||
| CsnVLanByPortCfgQos | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.7.1.2 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory The Stand alone stackable switch VLAN Priority values are: level0(0) -- low prority level1(1) -- high prority. The BigIron switch VLAN Priority values are: level0(0), level1(1), level2(2), level3(3), level4(4), level5(5), level6(6), level7(7)
| ||||
| CsnVLanByPortCfgStpMode | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.7.1.3 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Spanning Tree Mode in the Switch Group can be set either enabled or disabled and the default is enabled mode. enabled(1)...........activate Spanning Tree disabled(0)..........no Spanning Tree
| ||||
| CsnVLanByPortCfgStpPriority | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.7.1.4 | INTEGER (1..65535) | RW | mandatory |
column · INTEGER (1..65535) · read-write · mandatory dot1dStpPriority : The value of the write-able portion of the Stp ID, i.e., the first two octets of the (8 octet long) Bridge ID. The other (last) 6 octets of the Bridge ID are given by the value of the base bridge address - dot1dBaseBridgeAddress. | ||||
| CsnVLanByPortCfgStpGroupMaxAge | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.7.1.5 | INTEGER (6..40) | RW | mandatory |
column · INTEGER (6..40) · read-write · mandatory dot1dStpBridgeMaxAge: From RFC1493(Bridge MIB). The value that all bridges use for MaxAge when this bridge is acting as the root. Note that 802.1D-1990 specifies that the range for this parameter is related to the value of dot1dStpBridgeHelloTime. The granularity of this timer is specified by 802.1D-1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds. | ||||
| CsnVLanByPortCfgStpGroupHelloTime | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.7.1.6 | INTEGER (1..10) | RW | mandatory |
column · INTEGER (1..10) · read-write · mandatory dot1dStpBridgeHelloTime: From RFC1493(Bridge MIB). The value that all bridges use for HelloTime when this bridge is acting as the root. The granularity of this timer is specified by 802.1D- 1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds. | ||||
| CsnVLanByPortCfgStpGroupForwardDelay | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.7.1.7 | INTEGER (2..30) | RW | mandatory |
column · INTEGER (2..30) · read-write · mandatory dot1dStpBridgeForwardDelay : From RFC1493(Bridge MIB). The value that all bridges use for ForwardDelay when this bridge is acting as the root. Note that 802.1D-1990 specifies that the range for this parameter is related to the value of dot1dStpBridgeMaxAge. The granularity of this timer is specified by 802.1D-1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds. | ||||
| CsnVLanByPortCfgBaseNumPorts | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.7.1.8 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The number of ports controlled by this bridging entity. | ||||
| CsnVLanByPortCfgBaseType | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.7.1.9 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates what type of bridging this bridge can perform. If a bridge is actually performing a certain type of bridging this will be indicated by entries in the port table for the given type.
| ||||
| CsnVLanByPortCfgStpProtocolSpecification | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.7.1.10 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory An indication of what version of the Spanning Tree Protocol is being run. The value 'decLb100(2)' indicates the DEC LANbridge 100 Spanning Tree protocol. IEEE 802.1d implementations will return 'ieee8021d(3)'. If future versions of the IEEE Spanning Tree Protocol are released that are incompatible with the current version a new value will be defined.
| ||||
| CsnVLanByPortCfgStpMaxAge | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.7.1.11 | Timeout | RO | mandatory |
column · Timeout · read-only · mandatory dot1dStpMaxAge: From RFC1493(Bridge MIB). The maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded, in units of hundredths of a second. This is the actual value that this bridge is currently using. | ||||
| CsnVLanByPortCfgStpHelloTime | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.7.1.12 | Timeout | RO | mandatory |
column · Timeout · read-only · mandatory dot1dStpHelloTime: From RFC1493(Bridge MIB). The amount of time between the transmission of Configuration bridge PDUs by this node on any port when it is the root of the spanning tree or trying to become so, in units of hundredths of a second. This is the actual value that this bridge is currently using. | ||||
| CsnVLanByPortCfgStpHoldTime | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.7.1.13 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory dot1dStpHoldTime: From RFC1493(Bridge MIB). This time value determines the interval length during which no more than two Configuration bridge PDUs shall be transmitted by this node, in units of hundredths of a second. | ||||
| CsnVLanByPortCfgStpForwardDelay | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.7.1.14 | Timeout | RO | mandatory |
column · Timeout · read-only · mandatory dot1dStpForwardDelay: From RFC1493(Bridge MIB). This time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the Forwarding state. The value determines how long the port stays in each of the Listening and Learning states, which precede the Forwarding state. This value is also used, when a topology change has been detected and is underway, to age all dynamic entries in the Forwarding Database. [Note that this value is the one that this bridge is currently using, in contrast to dot1dStpBridgeForwardDelay which is the value that this bridge and all others would start using if/when this bridge were to become the root.] | ||||
| CsnVLanByPortCfgStpTimeSinceTopologyChange | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.7.1.15 | TimeTicks | RO | mandatory |
column · TimeTicks · read-only · mandatory The time (in hundredths of a second) since the last time a topology change was detected by the bridge entity. | ||||
| CsnVLanByPortCfgStpTopChanges | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.7.1.16 | Counter32 | RO | mandatory |
column · Counter32 · read-only · mandatory The total number of topology changes detected by this bridge since the management entity was last reset or initialized. | ||||
| CsnVLanByPortCfgStpRootCost | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.7.1.17 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory dot1dStpRootCost: From RFC1493(Bridge MIB). The cost of the path to the root as seen from this bridge. | ||||
| CsnVLanByPortCfgStpRootPort | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.7.1.18 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory dot1dStpRootPort: From RFC1493(Bridge MIB). The port number of the port which offers the lowest cost path from this bridge to the root bridge. | ||||
| CsnVLanByPortCfgStpDesignatedRoot | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.7.1.19 | BridgeId | RO | mandatory |
column · BridgeId · read-only · mandatory dot1dStpDesignatedRoot: From RFC1493(Bridge MIB). The bridge identifier of the root of the spanning tree as determined by the Spanning Tree Protocol as executed by this node. This value is used as the Root Identifier parameter in all Configuration Bridge PDUs originated by this node. | ||||
| CsnVLanByPortCfgBaseBridgeAddress | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.7.1.20 | MacAddress | RO | mandatory |
column · MacAddress · read-only · mandatory The MAC address used by this bridge when it must be referred to in a unique fashion. It is recommended that this be the numerically smallest MAC address of all ports that belong to this bridge. However it is only required to be unique. When concatenated with dot1dStpPriority a unique BridgeIdentifier is formed which is used in the Spanning Tree Protocol. | ||||
| CsnVLanByPortCfgVLanName | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.7.1.21 | DisplayString (SIZE (0..32)) | RW | mandatory |
column · DisplayString (SIZE (0..32)) · read-write · mandatory VLAN Community Name string. | ||||
| CsnVLanByPortCfgRouterIntf | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.7.1.22 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Optional: A virtual interface for router to the VLAN -- applied to router only. If a SNMP-Get value is zero, that means this object was not configured. | ||||
| CsnVLanByPortCfgRowStatus | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.2.7.1.23 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Use object to delete a vlan entry.
| ||||
| NsnSwPortInfo | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3 | |||
| TsnSwPortInfoTable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1 | NA | mandatory | |
table · not-accessible · mandatory A specific snSwPortInfo group consists of a number of switch ports. | ||||
| RsnSwPortInfoEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1 | NA | mandatory | |
row · not-accessible · mandatory An entry in the snSwPortInfo table indicates the configuration on a specified port. A SNMP SET PDU for a row of the snSwPortInfoTable requires the entired sequence of the MIB Objects in each snSwPortInfoEntry stored in one PDU. Otherwise, GENERR return-value will be returned.
| ||||
| CsnSwPortInfoPortNum | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The port index. The bit 0 to bit 7: port number. The bit 8 to bit 11: slot number (slot for chassis only). | ||||
| CsnSwPortInfoMonitorMode | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.2 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory A monitoring port is selected and its traffic will be
analyzed if the mode is not disabled(0), which is
the default mode.
The values are:
disabled(0) -- No traffic monitoring
input(1) -- traffic monitoring is activated on packets received
output(2) -- traffic monitoring is activated on packets transmitted
both(3) -- traffic monitoring is activated on packets
received and transmitted.
| ||||
| CsnSwPortInfoTagMode | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.3 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory For tagged port, we could have multiple VLANs per port. For untagged port or auto port, there is only one VLAN ID per port.
| ||||
| CsnSwPortInfoChnMode | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory The port can be configured to operate in either
half or full duplex mode. The values are:
halfDuplex(1)...half duplex mode
fullDuplex(2)...full duplex mode
The read-back channel status from hardware are:
none(0).........link down or port disabled.
halfDuplex(1)...half duplex mode
fullDuplex(2)...full duplex mode
The port media type (expansion or regular)
and port link type (trunk or feeder) determine
value of this object.
The port can not set to half duplex mode
if the port connect mode is m200e(4).
However, the value of this parameter may be
automatically set whenever the expansion port
is connected (e.g. cascade connecting device).
| ||||
| CsnSwPortInfoSpeed | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.5 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory The speed configuration for a port. The values are:
none(0)..........link down or no traffic.
sAutoSense(1)....Auto-sensing 10 or 100Mbits.
s10M(2)..........10Mbits per second.
s100M(3).........100Mbits per second.
s1G(4)...........1Gbits per second.
s45M(5)..........45Mbits per second (T3) (for expansion board only).
s155M(6).........155Mbits per second (ATM) (for expansion board only).
s10G(7)..........10Gbits per second.
The read-back hardware status are the following:
none(0)..........link down or no traffic.
s10M(2)..........10Mbits per second.
s100M(3).........100Mbits per second.
s1G(4)...........1Gbits per second.
s45M(5)..........45Mbits per second (T3) (for expansion board only).
s155M(6).........155Mbits per second (ATM) (for expansion board only).
s10G(7)..........10Gbits per second.
The port media type (expansion or regular)
and port link type (trunk or feeder) determine
whether this object can be written and the valid
values.
It is not allowed to change speed for trunks ports.
For expansion ports, all of the above speed
can be set.
However, the value of this parameter may be
automatically set whenever the expansion port
is connected (e.g. cascade connecting device).
| ||||
| CsnSwPortInfoMediaType | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.6 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The media type for the port. The values are: other(1).........other or unknown media. m100BaseTX(2)....100Mbits per second copper. m100BaseFX(3)....100Mbits per second fiber. m1000BaseFX(4)...1Gbits per second fiber. mT3(5)...........45Mbits per second (T3). m155ATM(6).......155Mbits per second (ATM). m1000BaseTX(7)...1Gbits per second copper. m622ATM(8).......622Mbits per second (ATM). m155POS(9).......155Mbits per second (POS). m622POS(10)......622Mbits per second (POS). m2488POS(11).....2488Mbits per second (POS). m10000BaseFX(12).10Gbits per second fiber.
| ||||
| CsnSwPortInfoConnectorType | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.7 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The type of connector that the port offers. The values are: other(1)...........other or unknown connector copper(2)..........Copper connector fiber(3)...........Fiber connector This describes the physical connector type
| ||||
| CsnSwPortInfoAdminStatus | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.8 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory The desired state of all ports. The testing(3) state indicates that no operational packets can be passed. (same as ifAdminStatus in MIB-II)
| ||||
| CsnSwPortInfoLinkStatus | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.9 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The current operational state of the interface. The testing(3) state indicates that no operational packets can be passed. (same as ifOperStatus in MIB-II)
| ||||
| CsnSwPortInfoPortQos | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.10 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory The Stand alone stackable switch Port Qos Priority values are: low(0) -- low prority high(1) -- high prority. The BigIron Port Qos Priority values are: level0(0), level1(1), level2(2), level3(3), level4(4), level5(5), level6(6), level7(7)
| ||||
| CsnSwPortInfoPhysAddress | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.11 | PhysAddress | RO | mandatory |
column · PhysAddress · read-only · mandatory The port physical address. The physical address represents the switch port. | ||||
| CsnSwPortStatsInFrames | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.12 | Counter32 | RO | mandatory |
column · Counter32 · read-only · mandatory The total number of packets received on the interface. | ||||
| CsnSwPortStatsOutFrames | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.13 | Counter32 | RO | mandatory |
column · Counter32 · read-only · mandatory The total number of packets transmitted out of the interface. | ||||
| CsnSwPortStatsAlignErrors | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.14 | Counter32 | RO | mandatory |
column · Counter32 · read-only · mandatory dot3StatsAlignmentErrors : A count of frames received on a particular interface that are not an integral number of octets in length and do not pass the FCS check. The count represented by an instance of this object is incremented when the alignmentError status is returned by the MAC service to the LLC (or other MAC user). Received frames for which multiple error conditions obtain are, according to the conventions of IEEE 802.3 Layer Management, counted exclusively according to the error status presented to the LLC. | ||||
| CsnSwPortStatsFCSErrors | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.15 | Counter32 | RO | mandatory |
column · Counter32 · read-only · mandatory dot3StatsFCSErrors : A count of frames received on a particular interface that are an integral number of octets in length but do not pass the FCS check. The count represented by an instance of this object is incremented when the frameCheckError status is returned by the MAC service to the LLC (or other MAC user). Received frames for which multiple error conditions obtain are, according to the conventions of IEEE 802.3 Layer Management, counted exclusively according to the error status presented to the LLC. | ||||
| CsnSwPortStatsMultiColliFrames | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.16 | Counter32 | RO | mandatory |
column · Counter32 · read-only · mandatory dot3StatsMultipleCollisionFrames : A count of successfully transmitted frames on a particular interface for which transmission is inhibited by more than one collision. A frame that is counted by an instance of this object is also counted by the corresponding instance of either the ifOutUcastPkts, ifOutMulticastPkts, or ifOutBroadcastPkts, and is not counted by the corresponding instance of the dot3StatsSingleCollisionFrames object. | ||||
| CsnSwPortStatsFrameTooLongs | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.17 | Counter32 | RO | mandatory |
column · Counter32 · read-only · mandatory dot3StatsFrameTooLongs : A count of frames received on a particular interface that exceed the maximum permitted frame size. The count represented by an instance of this object is incremented when the frameTooLong status is returned by the MAC service to the LLC (or other MAC user). Received frames for which multiple error conditions obtain are, according to the conventions of IEEE 802.3 Layer Management, counted exclusively according to the error status presented to the LLC. | ||||
| CsnSwPortStatsTxColliFrames | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.18 | Counter32 | RO | mandatory |
column · Counter32 · read-only · mandatory A count of successfully transmitted frames on a particular interface for which transmission is inhibited by more than one collision. A frame that is counted by a combination of both dot3StatsSingleCollisionFrames and dot3StatsMultipleCollisionFrames objects. | ||||
| CsnSwPortStatsRxColliFrames | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.19 | Counter32 | RO | mandatory |
column · Counter32 · read-only · mandatory A count of successfully received frames on a particular interface for which transmission is inhibited by more than one collision. This object is not specified in dot3 but it has the same functionarity as snSwPortStatsTxColliFrames. | ||||
| CsnSwPortStatsFrameTooShorts | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.20 | Counter32 | RO | mandatory |
column · Counter32 · read-only · mandatory A count of frames received on a particular interface that below the minimum permitted frame size. | ||||
| CsnSwPortLockAddressCount | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.21 | INTEGER (0..2048) | RW | mandatory |
column · INTEGER (0..2048) · read-write · mandatory The number of source MAC addresses are allowed for a port. Writing 0 to this object will allow any number of addresses. | ||||
| CsnSwPortStpPortEnable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.22 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory The enabled/disabled status of the port.
| ||||
| CsnSwPortDhcpGateListId | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.23 | INTEGER (0..32) | RW | mandatory |
column · INTEGER (0..32) · read-write · mandatory The ID for a DHCP gateway list entry relative to this switch port. 0 = unset or no assigned ID | ||||
| CsnSwPortName | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.24 | DisplayString (SIZE (0..255)) | RW | mandatory |
column · DisplayString (SIZE (0..255)) · read-write · mandatory Port Name string. | ||||
| CsnSwPortStatsInBcastFrames | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.25 | Counter32 | RO | mandatory |
column · Counter32 · read-only · mandatory The total number of broadcast packets received on the interface. | ||||
| CsnSwPortStatsOutBcastFrames | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.26 | Counter32 | RO | mandatory |
column · Counter32 · read-only · mandatory The total number of broadcast packets transmitted out of the interface. | ||||
| CsnSwPortStatsInMcastFrames | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.27 | Counter32 | RO | mandatory |
column · Counter32 · read-only · mandatory The total number of multicast packets received on the interface. | ||||
| CsnSwPortStatsOutMcastFrames | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.28 | Counter32 | RO | mandatory |
column · Counter32 · read-only · mandatory The total number of multicast packets transmitted out of the interface. | ||||
| CsnSwPortStatsInDiscard | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.29 | Counter32 | RO | mandatory |
column · Counter32 · read-only · mandatory The number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol. One possible reason for discarding such a packet could be to free up buffer space. | ||||
| CsnSwPortStatsOutDiscard | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.30 | Counter32 | RO | mandatory |
column · Counter32 · read-only · mandatory The number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a packet could be to free up buffer space. | ||||
| CsnSwPortStatsMacStations | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.31 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The total number of MAC Stations connected to the interface. | ||||
| CsnSwPortCacheGroupId | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.32 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Cache Group ID for the interface. | ||||
| CsnSwPortTransGroupId | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.33 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Transparent Group ID for the interface. | ||||
| CsnSwPortInfoAutoNegotiate | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.34 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory This feature only applies to Gigabit Ethernet ports. If set to disable(0), port will be put to non-negotiation mode. If set to enable(1), port will start auto-negotiation indefinitely until succeed. If set to negFullAuto(2), the port will start with auto- negotiation, if the negotiation failed, then it will automatically switch to non-negotiation mode. Stackable products (except TurboIron 8) Gigabit Ethernet ports do not support negFullAuto(2). If set to global(3), port negotiation mode follows the value of snSwGlobalAutoNegotiate. Non-Gigabit Ethernet port returns the value other(4).
| ||||
| CsnSwPortInfoFlowControl | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.35 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Enable/Disbale port flow control.
| ||||
| CsnSwPortInfoGigType | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.36 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The media type for the port. The values are: m1000BaseSX(0)....1Gbits per second fiber, with a short wavelength transceiver. m1000BaseLX(1)....1Gbits per second fiber, with a long wavelength transceiver (3km). m1000BaseLH(2)....1Gbits per second fiber, with a special wavelength transceiver (50km). m1000BaseLHA(3)....1Gbits per second fiber, with a special wavelength transceiver (70km). m1000BaseLHB(4)....1Gbits per second fiber, with a special wavelength transceiver (150km). m1000BaseTX(5)....1Gbits per second copper (100meter). m10000BaseSR(6)....10Gbits per second fiber, with a short range wavelength transceiver (100m). m10000BaseLR(7)....10Gbits per second fiber, with a long range wavelength transceiver (10km). m10000BaseER(8)....10Gbits per second fiber, with a extended range wavelength transceiver (40km). notApplicable(255)....a non-gigabit port.
| ||||
| CsnSwPortStatsLinkChange | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.37 | Counter32 | RO | mandatory |
column · Counter32 · read-only · mandatory The total number of link state change of the interface. | ||||
| CsnSwPortIfIndex | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.38 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory In order to identify a particular interface, this object shall identify the instance of the ifIndex object, defined in RFC 1213 and RFC 1573. | ||||
| CsnSwPortDescr | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.39 | DisplayString | RO | mandatory |
column · DisplayString · read-only · mandatory A textual string containing the slot/port information about the interface. | ||||
| CsnSwPortInOctets | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.40 | OCTET STRING (SIZE (8)) | RO | mandatory |
column · OCTET STRING (SIZE (8)) · read-only · mandatory The total number of octets received on the interface, including framing characters. This object is a 64-bit counter of the ifInOctets object, defined in RFC 1213. The octet string is in big-endian byte order. | ||||
| CsnSwPortOutOctets | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.41 | OCTET STRING (SIZE (8)) | RO | mandatory |
column · OCTET STRING (SIZE (8)) · read-only · mandatory The total number of octets transmitted out of the interface, including framing characters. This object is a 64-bit counter of the ifOutOctets object, defined in RFC 1213. The octet string is in big-endian byte order. | ||||
| CsnSwPortStatsInBitsPerSec | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.42 | Gauge32 | RO | mandatory |
column · Gauge32 · read-only · mandatory The number of bits per second received on the interface over a 5 minutes interval. | ||||
| CsnSwPortStatsOutBitsPerSec | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.43 | Gauge32 | RO | mandatory |
column · Gauge32 · read-only · mandatory The number of bits per second transmitted out of the interface over a 5 minutes interval. | ||||
| CsnSwPortStatsInPktsPerSec | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.44 | Gauge32 | RO | mandatory |
column · Gauge32 · read-only · mandatory The number of packets per second received on the interface over a 5 minutes interval. | ||||
| CsnSwPortStatsOutPktsPerSec | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.45 | Gauge32 | RO | mandatory |
column · Gauge32 · read-only · mandatory The number of packets per second transmitted out of the interface over a 5 minutes interval. | ||||
| CsnSwPortStatsInUtilization | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.46 | INTEGER (0..10000) | RO | mandatory |
column · INTEGER (0..10000) · read-only · mandatory The input network utilization in hundredths of a percent over a 5 minutes interval. | ||||
| CsnSwPortStatsOutUtilization | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.47 | INTEGER (0..10000) | RO | mandatory |
column · INTEGER (0..10000) · read-only · mandatory The output network utilization in hundredths of a percent over a 5 minutes interval. | ||||
| CsnSwPortFastSpanPortEnable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.48 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory The enabled/disabled fast span port status of the port.
| ||||
| CsnSwPortFastSpanUplinkEnable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.49 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory The enabled/disabled fast span uplink status of the port.
| ||||
| CsnSwPortVlanId | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.50 | INTEGER (0..4095) | RW | mandatory |
column · INTEGER (0..4095) · read-write · mandatory The ID of a VLAN of which this port is a member. Port must be untagged. For tagged port which belongs to multiple VLANs, this object return 0 which is an invalid VLAN ID value. | ||||
| CsnSwPortRouteOnly | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.51 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Enable/Disable L2 switching of a routing switch port. By default, the routing switch performs routing first. If routing failed, it performs switching. Enable route only instrcuts the routing switch to perform routing only. For a L2 switching only product, reading this object always return 'disabled', writing 'enabled' to this object takes no effect.
| ||||
| CsnSwPortPresent | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.52 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicate if the port is absent or present. This object only valid for M4 module
| ||||
| CsnSwPortGBICStatus | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.53 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicate if the gig port has GBICs on them. If set to GBIC(1), it means that the port is GBIC. If set to miniGBIC(2), it means that the port miniGBIC. If set to empty(3), it means that the GBIC is missing. Value other(4) means that the port not a removable gig port.
| ||||
| CsnSwPortStatsInKiloBitsPerSec | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.54 | Unsigned32 | RO | mandatory |
column · Unsigned32 · read-only · mandatory Bit rate in kilobits per second received on the 10G and faster interface over a 5 minutes interval. | ||||
| CsnSwPortStatsOutKiloBitsPerSec | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.55 | Unsigned32 | RO | mandatory |
column · Unsigned32 · read-only · mandatory Bit rate in kilobits per second transmitted out of the 10G and faster interface over a 5 minutes interval. | ||||
| CsnSwPortLoadInterval | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.56 | INTEGER (30..300) | RW | mandatory |
column · INTEGER (30..300) · read-write · mandatory The time in seconds for which average port utilization should be carried out. The value should be incremental of 30 seconds, between the ranges specified. | ||||
| CsnSwPortTagType | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.1.1.57 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory The IEEE802.1q tag type embedded in the length/type field of an Ethernet packet. It specifies that the 2 octets after the length/type field in an Ethernet packet is the tag value. | ||||
| NsnInterfaceId | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.2 | |||
| TsnInterfaceLookupTable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.3 | NA | mandatory | |
| RsnInterfaceLookupEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.3.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CsnInterfaceLookupInterfaceId | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.3.1.1 | InterfaceId | RO | mandatory |
| CsnInterfaceLookupIfIndex | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.3.1.2 | INTEGER | RO | mandatory |
| TsnIfIndexLookupTable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.4 | NA | mandatory | |
| RsnIfIndexLookupEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.4.1 | NA | mandatory | |
row · not-accessible · mandatory | ||||
| CsnIfIndexLookupIfIndex | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.4.1.1 | INTEGER | RO | mandatory |
| CsnIfIndexLookupInterfaceId | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.3.4.1.2 | InterfaceId | RO | mandatory |
| NsnFdbInfo | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.4 | |||
| TsnFdbTable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.4.1 | NA | mandatory | |
table · not-accessible · mandatory This table contains snFdb information for each station known to the system, one entry per station. | ||||
| RsnFdbEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.4.1.1 | NA | mandatory | |
row · not-accessible · mandatory Each entry represents the information of a static MAC station.
| ||||
| CsnFdbStationIndex | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.4.1.1.1 | INTEGER (1..256) | RO | mandatory |
column · INTEGER (1..256) · read-only · mandatory The FDB Station index to the Fdb Station Table. | ||||
| CsnFdbStationAddr | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.4.1.1.2 | PhysAddress | RW | mandatory |
column · PhysAddress · read-write · mandatory The snFdbs physical address. The physical address represents a MAC Station. | ||||
| CsnFdbStationPort | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.4.1.1.3 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Station slot/port number. The bit 0 to bit 7: port number. The bit 8 to bit 11: slot number (slot for chassis only). | ||||
| CsnFdbVLanId | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.4.1.1.4 | INTEGER (1..65535) | RW | mandatory |
column · INTEGER (1..65535) · read-write · mandatory The Station VLan ID. | ||||
| CsnFdbStationQos | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.4.1.1.5 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory The Stand alone stackable station Qos Priority values are: low(0) -- low prority high(1) -- high prority. The BigIron switch station Priority values are: level0(0), level1(1), level2(2), level3(3), level4(4), level5(5), level6(6), level7(7)
| ||||
| CsnFdbStationType | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.4.1.1.6 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory The station type values are:
notSupported -- a read value only : this product does not
support MultiLayer Switching.
host -- any MAC station.
router -- a router-typed station.
| ||||
| CsnFdbRowStatus | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.4.1.1.7 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row other(1)....some other case valid(2)....the row exists and is valid
| ||||
| NsnPortStpInfo | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.5 | |||
| TsnPortStpTable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.5.1 | NA | mandatory | |
table · not-accessible · mandatory A specific snPortStpTable consists of a number of switch ports. This table only exists if only if snVLanByPortTable exists and snVLanByPortStpMode is enabled for each VLAN. | ||||
| RsnPortStpEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.5.1.1 | NA | mandatory | |
row · not-accessible · mandatory An entry in the snPortStpTable indicates the configuration on a specified port. A SNMP SET PDU for a row of the snPortStpTable requires the entired sequence of the MIB Objects in each snPortStpEntry stored in one PDU. Otherwise, GENERR return-value will be returned. | ||||
| CsnPortStpVLanId | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.5.1.1.1 | INTEGER (1..65535) | RO | mandatory |
column · INTEGER (1..65535) · read-only · mandatory The VLAN ID of the VLAN switch community. | ||||
| CsnPortStpPortNum | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.5.1.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The port number of the Switch. The bit 0 to bit 7: port number. The bit 8 to bit 11: slot number (slot for chassis only). | ||||
| CsnPortStpPortPriority | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.5.1.1.3 | INTEGER (8..255) | RW | mandatory |
column · INTEGER (8..255) · read-write · mandatory The value of the priority field which is contained in the first (in network byte order) octet of the (2 octet long) Port ID. The other octet of the Port ID is given by the value of dot1dStpPort. | ||||
| CsnPortStpPathCost | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.5.1.1.4 | INTEGER (0..65535) | RW | mandatory |
column · INTEGER (0..65535) · read-write · mandatory dot1dStpPortPathCost : The contribution of this port to the path cost of paths towards the spanning tree root which include this port. 802.1D-1990 recommends that the default value of this parameter be in inverse proportion to the speed of the attached LAN. Writing value zero to this object sets path cost to a default value which automatically changes according to port speed. Reading value zero indicates an unknown path cost value because port speed cannot be determined due to speed auto sense in progress. | ||||
| CsnPortStpOperState | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.5.1.1.5 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory By default, this mode is set to notActivated(0). notActivated(0)...the Port STP entry is not activated and not in running mode. activated(1)......the Port STP entry is activated and in running mode
| ||||
| CsnPortStpPortEnable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.5.1.1.6 | INTEGER | NA | mandatory |
column · INTEGER · not-accessible · mandatory The enabled/disabled status of the port.
| ||||
| CsnPortStpPortForwardTransitions | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.5.1.1.7 | Counter32 | NA | mandatory |
column · Counter32 · not-accessible · mandatory The number of times this port has transitioned from the Learning state to the Forwarding state. | ||||
| CsnPortStpPortState | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.5.1.1.8 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The port's current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame. If the bridge has detected a port that is malfunctioning it will place that port into the broken(6) state. For ports which are disabled (see dot1dStpPortEnable), this object will have a value of disabled(1).
| ||||
| CsnPortStpPortDesignatedCost | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.5.1.1.9 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The path cost of the Designated Port of the segment connected to this port. This value is compared to the Root Path Cost field in received bridge PDUs. | ||||
| CsnPortStpPortDesignatedRoot | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.5.1.1.10 | BridgeId | RO | mandatory |
column · BridgeId · read-only · mandatory The unique Bridge Identifier of the Bridge recorded as the Root in the Configuration BPDUs transmitted by the Designated Bridge for the segment to which the port is attached. | ||||
| CsnPortStpPortDesignatedBridge | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.5.1.1.11 | BridgeId | RO | mandatory |
column · BridgeId · read-only · mandatory The Bridge Identifier of the bridge which this port considers to be the Designated Bridge for this port's segment. | ||||
| CsnPortStpPortDesignatedPort | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.5.1.1.12 | OCTET STRING (SIZE (2)) | RO | mandatory |
column · OCTET STRING (SIZE (2)) · read-only · mandatory The Port Identifier of the port on the Designated Bridge for this port's segment. | ||||
| NsnTrunkInfo | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.6 | |||
| TsnTrunkTable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.6.1 | NA | mandatory | |
table · not-accessible · mandatory A specific snTrunkTable consists of a number of Trunk port-mask. | ||||
| RsnTrunkEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.6.1.1 | NA | mandatory | |
row · not-accessible · mandatory An entry in the snTrunkTable indicates the configuration on a specified Trunk port membership.
| ||||
| CsnTrunkIndex | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.6.1.1.1 | INTEGER (1..64) | RO | mandatory |
column · INTEGER (1..64) · read-only · mandatory The number of the trunk entries can be configured. | ||||
| CsnTrunkPortMask | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.6.1.1.2 | PortMask | RW | mandatory |
column · PortMask · read-write · mandatory Trunk membership of the Switch. | ||||
| CsnTrunkType | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.6.1.1.3 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory The trunk connection type which specifies what device the trunk ports are connected to.
| ||||
| TsnMSTrunkTable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.6.2 | NA | mandatory | |
table · not-accessible · mandatory A table contains the configuration of port members of multi-slot trunk groups. | ||||
| RsnMSTrunkEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.6.2.1 | NA | mandatory | |
| CsnMSTrunkPortIndex | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.6.2.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The primary port of a trunk group. For module with Gig ports, primary port is port 1, 3, 5, 7. For module with 10/100 ports, primary port is port 1, 5, 9, 13, 17, 21. | ||||
| CsnMSTrunkPortList | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.6.2.1.2 | OCTET STRING | RW | mandatory |
column · OCTET STRING · read-write · mandatory A list of port indices which are the port membership of a trunk group. Each port index is a 16-bit integer in big endian order. The first port index must be the primary port index. | ||||
| CsnMSTrunkType | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.6.2.1.3 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory The trunk connection type which specifies what device the trunk ports are connected to.
| ||||
| CsnMSTrunkRowStatus | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.6.2.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory To create or delete a table entry.
| ||||
| NsnSwSummary | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.7 | |||
| SsnSwSummaryMode | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.7.1 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory The Switch Group Configuration Summary is configured either enabled or disabled and the default is disabled mode. enabled(1)...........activate Switch Configuration Summary. disabled(0)..........no Switch Configuration Summary.
| ||||
| NsnDhcpGatewayListInfo | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.8 | |||
| TsnDhcpGatewayListTable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.8.1 | NA | mandatory | |
table · not-accessible · mandatory A table of DHCP gateway list of addresses. | ||||
| RsnDhcpGatewayListEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.8.1.1 | NA | mandatory | |
| CsnDhcpGatewayListId | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.8.1.1.1 | INTEGER (1..32) | RO | mandatory |
column · INTEGER (1..32) · read-only · mandatory The ID for a DHCP gateway list entry. | ||||
| CsnDhcpGatewayListAddrList | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.8.1.1.2 | OCTET STRING (SIZE (4..32)) | RW | mandatory |
column · OCTET STRING (SIZE (4..32)) · read-write · mandatory The DHCP gateway address list for each DHCP gateway list ID. This list contains 1 to 8 IP addresses represented by octet string. | ||||
| CsnDhcpGatewayListRowStatus | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.8.1.1.3 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row or modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row other(1)....some other case valid(2)....the row exists and is valid
| ||||
| NsnDnsInfo | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.9 | |||
| SsnDnsDomainName | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.9.1 | DisplayString (SIZE (0..80)) | RW | mandatory |
scalar · DisplayString (SIZE (0..80)) · read-write · mandatory DNS Domain Name string. | ||||
| SsnDnsGatewayIpAddrList | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.9.2 | OCTET STRING (SIZE (16)) | RW | mandatory |
scalar · OCTET STRING (SIZE (16)) · read-write · mandatory The DNS Gateway IP address list. This list contains 4 IP addresses represented by octet string. | ||||
| NsnMacFilter | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.10 | |||
| TsnMacFilterTable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.1 | NA | mandatory | |
table · not-accessible · mandatory MAC filter table. | ||||
| RsnMacFilterEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.1.1 | NA | mandatory | |
| CsnMacFilterIndex | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The table index for a filter entry. | ||||
| CsnMacFilterAction | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.1.1.2 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Action to take if the Mac packet match with this filter.
| ||||
| CsnMacFilterSourceMac | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.1.1.3 | MacAddress | RW | mandatory |
column · MacAddress · read-write · mandatory Source MAC address. | ||||
| CsnMacFilterSourceMask | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.1.1.4 | MacAddress | RW | mandatory |
column · MacAddress · read-write · mandatory Source MAC subnet mask. | ||||
| CsnMacFilterDestMac | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.1.1.5 | MacAddress | RW | mandatory |
column · MacAddress · read-write · mandatory Destination MAC address. | ||||
| CsnMacFilterDestMask | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.1.1.6 | MacAddress | RW | mandatory |
column · MacAddress · read-write · mandatory Destination MAC subnet mask. | ||||
| CsnMacFilterOperator | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.1.1.7 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Type of comparison to perform.
| ||||
| CsnMacFilterFrameType | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.1.1.8 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Frame Type: ethernet-type, LLC and SNAP types
| ||||
| CsnMacFilterFrameTypeNum | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.1.1.9 | INTEGER (0..65535) | RW | mandatory |
column · INTEGER (0..65535) · read-write · mandatory Frame Type Number. 0 means NA | ||||
| CsnMacFilterRowStatus | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.1.1.10 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory This object is used to create and
delete row in the table and control
if they are used. The values
that can be written are:
delete(3)...deletes the row
create(4)...creates a new row
modify(5)...modifies an exsisting row
If the row exists, then a SET with
value of create(4) returns error
'badValue'. Deleted rows go away
immediately. The following values
can be returned on reads:
noSuch(0)...no such row
invalid(1)...Setting it to 'invalid' has the effect of
rendering it inoperative..
valid(2)....the row exists and is valid
| ||||
| TsnMacFilterPortAccessTable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.2 | NA | mandatory | |
table · not-accessible · mandatory MAC Filter port access table. | ||||
| RsnMacFilterPortAccessEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.2.1 | NA | mandatory | |
row · not-accessible · mandatory An entry in the MAC Filter Port access table. | ||||
| CsnMacFilterPortAccessPortIndex | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.2.1.1 | INTEGER (1..3900) | RO | mandatory |
column · INTEGER (1..3900) · read-only · mandatory The port index. For FastIron/NetIron products, port index value is from 1 to 42 For BigIron products, port index is an encoded number: The bit 0 to bit 7: port number. The bit 8 to bit 11: slot number. For virtual router interface, slot number is 15, port number is the virtual router port from 1 to 60. Therefore, port index value for BigIron is from 257 to 3900. | ||||
| CsnMacFilterPortAccessFilters | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.2.1.2 | OCTET STRING | RW | mandatory |
column · OCTET STRING · read-write · mandatory 1st octet correspond to 1st filter number and so on. | ||||
| CsnMacFilterPortAccessRowStatus | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.10.2.1.3 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory This object is used to create and
delete row in the table and control
if they are used. The values
that can be written are:
delete(3)...deletes the row
create(4)...creates a new row
If the row exists, then a SET with
value of create(4) returns error
'badValue'. Deleted rows go away
immediately. The following values
can be returned on reads:
noSuch(0)...no such row
invalid(1)...Setting it to 'invalid' has the effect of
rendering it inoperative..
valid(2)....the row exists and is valid
| ||||
| NsnNTP | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.11 | |||
| NsnNTPGeneral | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.11.1 | |||
| SsnNTPPollInterval | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.11.1.1 | INTEGER (1..65535) | RW | mandatory |
scalar · INTEGER (1..65535) · read-write · mandatory Interval specifies how often to poll the NTP server. Each unit is one second. | ||||
| SsnNTPTimeZone | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.11.1.2 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Time zone.
| ||||
| SsnNTPSummerTimeEnable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.11.1.3 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Enable/Disable daylight saving time. This enables daylight saving time for time/date starting 02:00:00 of first Sunday in April and ending 02:00:00 of last Sunday in October every year.
| ||||
| SsnNTPSystemClock | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.11.1.4 | OCTET STRING (SIZE (7)) | RW | mandatory |
scalar · OCTET STRING (SIZE (7)) · read-write · mandatory System clock, in the following format: octet 0: seconds after the minute [0-60] octet 1: minutes after the hour [0-59] octet 2: hours since midnight [0-23] octet 3: day of the month [1-31] octet 4: months since January [0-11] octet 5: years since 1900 octet 6: days since Sunday [0-6] Setting this object requires valid value in octets 0 to 5, and zero in octet 6. System clock can be disabled by setting zero to all octets. | ||||
| SsnNTPSync | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.11.1.5 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Initiate time synchronization to the NTP servers. For set operation, only 'synchronize(2)' is accepted. For get operation, always return 'other(1)'.
| ||||
| TsnNTPServerTable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.11.2 | NA | mandatory | |
table · not-accessible · mandatory NTP (Network Time Protocol) server table. | ||||
| RsnNTPServerEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.11.2.1 | NA | mandatory | |
| CsnNTPServerIp | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.11.2.1.1 | IpAddress | RO | mandatory |
column · IpAddress · read-only · mandatory NTP server IP address. | ||||
| CsnNTPServerVersion | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.11.2.1.2 | INTEGER (1..4) | RW | mandatory |
column · INTEGER (1..4) · read-write · mandatory NTP server version. | ||||
| CsnNTPServerRowStatus | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.11.2.1.3 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory To create or delete a NTP server table entry.
| ||||
| NsnRadius | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.12 | |||
| NsnRadiusGeneral | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.1 | |||
| SsnRadiusSNMPAccess | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.1.1 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory Indicate whether Radius group MIB obejcts can be accessed by SNMP manager. If value is disabled, all Radius group MIB objects return 'general error'.
| ||||
| SsnRadiusEnableTelnetAuth | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.1.2 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Enable/Disable telnet authentication specified by 'snRadiusLoginMethod'.
| ||||
| SsnRadiusRetransmit | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.1.3 | INTEGER (0..5) | RW | mandatory |
scalar · INTEGER (0..5) · read-write · mandatory The number of authentication query retransmissions to the Radius server. | ||||
| SsnRadiusTimeOut | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.1.4 | INTEGER (1..15) | RW | mandatory |
scalar · INTEGER (1..15) · read-write · mandatory Interval specifies how long to wait for authentication reply from the Radius server, each unit is one second. | ||||
| SsnRadiusDeadTime | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.1.5 | INTEGER (1..5) | RW | mandatory |
scalar · INTEGER (1..5) · read-write · mandatory Interval specifies Radius server dead time, each unit is one minute. | ||||
| SsnRadiusKey | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.1.6 | DisplayString (SIZE (0..32)) | RW | mandatory |
scalar · DisplayString (SIZE (0..32)) · read-write · mandatory Authentication key displayed as encrypted text. | ||||
| SsnRadiusLoginMethod | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.1.7 | OCTET STRING (SIZE (0..7)) | RW | mandatory |
scalar · OCTET STRING (SIZE (0..7)) · read-write · mandatory A sequence of authentication methods. Each octet represents
a method to authenticate the user login process. Each octet
has the following enumeration value:
enable(1) - authenticate by command line interface
enable password
radius(2) - authenticate by requesting radius server
local(3) - authenticate by local user account table
line(4) - authenticate by telnet password
tacplus(5) - authenticate by requesting tacplus server
none(6) - do not authenticate
tacacs(7) - authenticate by requesting tacacs server
Setting a zero length octet string invalidates all
previous authentication methods. | ||||
| SsnRadiusEnableMethod | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.1.8 | OCTET STRING (SIZE (0..7)) | RW | mandatory |
scalar · OCTET STRING (SIZE (0..7)) · read-write · mandatory A sequence of authentication methods. Each octet represents
a method to authenticate the user entering priviledge mode
of the command line interface. Each octet has the following
enumeration value:
enable(1) - authenticate by command line interface
enable password
radius(2) - authenticate by requesting radius server
local(3) - authenticate by local user account table
line(4) - authenticate by telnet password
tacplus(5) - authenticate by requesting tacplus server
none(6) - do not authenticate
tacacs(7) - authenticate by requesting tacacs server
Setting a zero length octet string invalidates all
previous authentication methods. | ||||
| SsnRadiusWebServerMethod | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.1.9 | OCTET STRING (SIZE (0..7)) | RW | mandatory |
scalar · OCTET STRING (SIZE (0..7)) · read-write · mandatory A sequence of authentication methods. Each octet represents
a method to authenticate the user accessing the web-server.
Each octet has the following enumeration value:
enable(1) - authenticate by command line interface
enable password
radius(2) - authenticate by requesting radius server
local(3) - authenticate by local user account table
line(4) - authenticate by telnet password
tacplus(5) - authenticate by requesting tacplus server
none(6) - do not authenticate
tacacs(7) - authenticate by requesting tacacs server
Setting a zero length octet string invalidates all
previous authentication methods. | ||||
| SsnRadiusSNMPServerMethod | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.1.10 | OCTET STRING (SIZE (0..7)) | RW | mandatory |
scalar · OCTET STRING (SIZE (0..7)) · read-write · mandatory A sequence of authentication methods. Each octet represents
a method to authenticate the user accessing the snmp-server.
Each octet has the following enumeration value:
enable(1) - authenticate by command line interface
enable password
radius(2) - authenticate by requesting radius server
local(3) - authenticate by local user account table
line(4) - authenticate by telnet password
tacplus(5) - authenticate by requesting tacplus server
none(6) - do not authenticate
tacacs(7) - authenticate by requesting tacacs server
Setting a zero length octet string invalidates all
previous authentication methods. | ||||
| TsnRadiusServerTable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.2 | NA | mandatory | |
table · not-accessible · mandatory Radius server table. | ||||
| RsnRadiusServerEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.2.1 | NA | mandatory | |
| CsnRadiusServerIp | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.2.1.1 | IpAddress | RO | mandatory |
column · IpAddress · read-only · mandatory Radius server IP address. | ||||
| CsnRadiusServerAuthPort | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.2.1.2 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Authentication UDP port number. | ||||
| CsnRadiusServerAcctPort | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.2.1.3 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Account UDP port number. | ||||
| CsnRadiusServerRowStatus | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.2.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory To create or delete a Radius server table entry.
| ||||
| CsnRadiusServerRowKey | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.2.1.5 | DisplayString (SIZE (0..32)) | RW | mandatory |
column · DisplayString (SIZE (0..32)) · read-write · mandatory Authentication key displayed as encrypted text. | ||||
| CsnRadiusServerUsage | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.12.2.1.6 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory To allow this server to be dedicated for a particular AAA activity.
| ||||
| NsnTacacs | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.13 | |||
| NsnTacacsGeneral | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.13.1 | |||
| SsnTacacsRetransmit | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.13.1.1 | INTEGER (0..5) | RW | mandatory |
scalar · INTEGER (0..5) · read-write · mandatory The number of authentication query retransmissions to the Tacacs server. | ||||
| SsnTacacsTimeOut | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.13.1.2 | INTEGER (1..15) | RW | mandatory |
scalar · INTEGER (1..15) · read-write · mandatory Interval specifies how long to wait for authentication reply from the Tacacs server, each unit is one second. | ||||
| SsnTacacsDeadTime | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.13.1.3 | INTEGER (1..5) | RW | mandatory |
scalar · INTEGER (1..5) · read-write · mandatory Interval specifies Tacacs server dead time, each unit is one minute. | ||||
| SsnTacacsKey | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.13.1.4 | DisplayString (SIZE (0..32)) | RW | mandatory |
scalar · DisplayString (SIZE (0..32)) · read-write · mandatory Authentication key displayed as encrypted text. | ||||
| SsnTacacsSNMPAccess | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.13.1.5 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory Indicate whether Tacacs group MIB obejcts can be accessed by SNMP manager. If value is disabled, all Tacacs group MIB objects return 'general error'.
| ||||
| TsnTacacsServerTable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.13.2 | NA | mandatory | |
table · not-accessible · mandatory Tacacs server table. | ||||
| RsnTacacsServerEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.13.2.1 | NA | mandatory | |
| CsnTacacsServerIp | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.13.2.1.1 | IpAddress | RO | mandatory |
column · IpAddress · read-only · mandatory Tacacs server IP address. | ||||
| CsnTacacsServerAuthPort | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.13.2.1.2 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Authentication UDP port number. | ||||
| CsnTacacsServerRowStatus | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.13.2.1.3 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory To create or delete a Tacacs server table entry.
| ||||
| CsnTacacsServerRowKey | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.13.2.1.4 | DisplayString (SIZE (0..32)) | RW | mandatory |
column · DisplayString (SIZE (0..32)) · read-write · mandatory Authentication key displayed as encrypted text. | ||||
| CsnTacacsServerUsage | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.13.2.1.5 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory To allow this server to be dedicated for a particular AAA activity.
| ||||
| NsnQos | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.14 | |||
| TsnQosProfileTable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.14.1 | NA | mandatory | |
table · not-accessible · mandatory A table contains the configuration of qos profile groups. | ||||
| RsnQosProfileEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.14.1.1 | NA | mandatory | |
| CsnQosProfileIndex | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.14.1.1.1 | INTEGER (1..4) | RO | mandatory |
column · INTEGER (1..4) · read-only · mandatory The table index of QOS Profile. | ||||
| CsnQosProfileName | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.14.1.1.2 | DisplayString (SIZE (0..32)) | RW | mandatory |
column · DisplayString (SIZE (0..32)) · read-write · mandatory Qos Profile Name string. | ||||
| CsnQosProfileRequestedBandwidth | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.14.1.1.3 | INTEGER (0..100) | RW | mandatory |
column · INTEGER (0..100) · read-write · mandatory Qos Profile Requested Bandwidth. | ||||
| CsnQosProfileCalculatedBandwidth | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.14.1.1.4 | INTEGER (0..100) | RO | mandatory |
column · INTEGER (0..100) · read-only · mandatory Qos Profile Calculated Bandwidth. | ||||
| TsnQosBindTable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.14.2 | NA | mandatory | |
table · not-accessible · mandatory A table contains the configuration of 802.1p to qos profile binding groups. | ||||
| RsnQosBindEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.14.2.1 | NA | mandatory | |
| CsnQosBindIndex | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.14.2.1.1 | INTEGER (1..8) | RO | mandatory |
column · INTEGER (1..8) · read-only · mandatory The table index of QOS Bind. | ||||
| CsnQosBindPriority | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.14.2.1.2 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory QOS bind priority. | ||||
| CsnQosBindProfileIndex | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.14.2.1.3 | INTEGER (1..4) | RW | mandatory |
column · INTEGER (1..4) · read-write · mandatory QOS Bind Profile Index. This is pointer to the index of snQosProfile Table. | ||||
| NsnAAA | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.15 | |||
| NsnAuthentication | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.15.1 | |||
| NsnAuthorization | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.15.2 | |||
| SsnAuthorizationCommandMethods | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.15.2.1 | OCTET STRING (SIZE (0..3)) | RW | mandatory |
scalar · OCTET STRING (SIZE (0..3)) · read-write · mandatory A sequence of authorization methods. Each octet represents a method to authorize the user command. Each octet has the following value: radius(2) - authorize by requesting radius server tacplus(5) - authorize by requesting tacplus server none(6) - skip authorization Setting a zero length octet string invalidates all previous authorization methods. | ||||
| SsnAuthorizationCommandLevel | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.15.2.2 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Commands, which are equal to and less than the specified command level here needs to be authorized. Possible enumeration values: 0 - Privilege level 0 4 - Privilege level 4 5 - Privilege level 5.
| ||||
| SsnAuthorizationExec | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.15.2.3 | OCTET STRING (SIZE (0..3)) | RW | mandatory |
scalar · OCTET STRING (SIZE (0..3)) · read-write · mandatory A sequence of exec authorization methods. Each octet represents a method for telnet or SSH login authorization. Each octet has the following enumeration value: radius(2) - send exec authorization request to radius server tacplus(5) - send exec authorization request to tacplus server none(6) - no exec authorization Setting a zero length octet string invalidates all authorization methods. | ||||
| NsnAccounting | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.15.3 | |||
| SsnAccountingCommandMethods | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.15.3.1 | OCTET STRING (SIZE (0..3)) | RW | mandatory |
scalar · OCTET STRING (SIZE (0..3)) · read-write · mandatory A sequence of accounting methods. Each octet represents a method to account for the user command. Each octet has the following enumeration value: radius(2) - send accounting info to radius server tacplus(5) - send accounting info to tacplus server none(6) - skip accounting Setting a zero length octet string invalidates all previous accounting methods. | ||||
| SsnAccountingCommandLevel | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.15.3.2 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Commands, which are equal to and less than the specified command level here will be accounted. Possible enumeration values: level0 - Privilege level 0 level4 - Privilege level 4 level5 - Privilege level 5.
| ||||
| SsnAccountingExec | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.15.3.3 | OCTET STRING (SIZE (0..3)) | RW | mandatory |
scalar · OCTET STRING (SIZE (0..3)) · read-write · mandatory A sequence of accounting methods. Each octet represents a method for telnet or SSH login accounting. Each octet has the following enumeration value: radius(2) - send accounting info to radius server tacplus(5) - send accounting info to tacplus server none(6) - skip accounting Setting a zero length octet string invalidates all previous accounting methods. | ||||
| SsnAccountingSystem | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.15.3.4 | OCTET STRING (SIZE (0..3)) | RW | mandatory |
scalar · OCTET STRING (SIZE (0..3)) · read-write · mandatory A sequence of accounting methods. Each octet represents a method to account for the system related events. Each octet has the following enumeration value: radius(2) - send accounting info to radius server tacplus(5) - send accounting info to tacplus server none(6) - skip accounting Setting a zero length octet string invalidates all previous accounting methods. | ||||
| NsnCAR | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.16 | |||
| NsnVLanCAR | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.17 | |||
| NsnNetFlow | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.18 | |||
| NsnNetFlowGlb | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.18.1 | |||
| SsnNetFlowGblEnable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.18.1.1 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Enable/disable NetFlow export operation.
| ||||
| SsnNetFlowGblVersion | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.18.1.2 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory NetFlow export version.
| ||||
| SsnNetFlowGblProtocolDisable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.18.1.3 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory bit 0 - other, disable all protocols export except UDP and TCP bit 1 - tcp, disable TCP protocol export bit 2 - udp, disable UDP protocol export | ||||
| SsnNetFlowGblActiveTimeout | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.18.1.4 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Maximum time an active flow can be in the NetFlow cache (minutes: 1..60) | ||||
| SsnNetFlowGblInactiveTimeout | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.18.1.5 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Maximum time an inactive flow can be in the NetFlow cache (seconds: 10..600) | ||||
| TsnNetFlowCollectorTable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.18.2 | NA | mandatory | |
table · not-accessible · mandatory A table of each NetFlow collector information. | ||||
| RsnNetFlowCollectorEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.18.2.1 | NA | mandatory | |
| CsnNetFlowCollectorIndex | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.18.2.1.1 | INTEGER (1..10) | RO | mandatory |
column · INTEGER (1..10) · read-only · mandatory The index to the NetFlow collector table. | ||||
| CsnNetFlowCollectorIp | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.18.2.1.2 | IpAddress | RW | mandatory |
column · IpAddress · read-write · mandatory The NetFlow collector ip address. | ||||
| CsnNetFlowCollectorUdpPort | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.18.2.1.3 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory The NetFlow collector UDP port number. | ||||
| CsnNetFlowCollectorSourceInterface | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.18.2.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory The ifIndex value to specify source port to export NetFlow packet. Value 0 to indicate default outgoing port. | ||||
| CsnNetFlowCollectorRowStatus | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.18.2.1.5 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory To create or delete a NetFlow collector table entry.
| ||||
| TsnNetFlowAggregationTable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.18.3 | NA | mandatory | |
table · not-accessible · mandatory A table of each NetFlow aggregation scheme information. | ||||
| RsnNetFlowAggregationEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.18.3.1 | NA | mandatory | |
row · not-accessible · mandatory A row in the NetFlow Aggregation table. | ||||
| CsnNetFlowAggregationIndex | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.18.3.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The Aggregation scheme ID
| ||||
| CsnNetFlowAggregationIp | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.18.3.1.2 | IpAddress | RW | mandatory |
column · IpAddress · read-write · mandatory The NetFlow aggregation collector ip address. | ||||
| CsnNetFlowAggregationUdpPort | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.18.3.1.3 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory The NetFlow aggregation collector UDP port number. | ||||
| CsnNetFlowAggregationSourceInterface | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.18.3.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory The ifIndex value to specify source port to export NetFlow aggregation packet. Value 0 to indicate default outgoing port. | ||||
| CsnNetFlowAggregationNumberOfCacheEntries | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.18.3.1.5 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Number of cache entries for aggregation scheme | ||||
| CsnNetFlowAggregationActiveTimeout | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.18.3.1.6 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Maximum time an active flow can be in the aggregation cache | ||||
| CsnNetFlowAggregationInactiveTimeout | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.18.3.1.7 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Maximum time an inactive flow can be in the aggregation cache | ||||
| CsnNetFlowAggregationEnable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.18.3.1.8 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Enable/disable NetFlow aggregation for this aggregation scheme.
| ||||
| CsnNetFlowAggregationRowStatus | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.18.3.1.9 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory To create or delete a NetFlow collector table entry.
| ||||
| TsnNetFlowIfTable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.18.4 | NA | mandatory | |
table · not-accessible · mandatory A list of interface entries. The number of entries is given by the value of ifNumber. | ||||
| RsnNetFlowIfEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.18.4.1 | NA | mandatory | |
row · not-accessible · mandatory Entry containing the type of switching performed on that interface.
| ||||
| CsnNetFlowIfIndex | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.18.4.1.1 | INTEGER (1..65536) | RO | mandatory |
column · INTEGER (1..65536) · read-only · mandatory A unique value, greater than zero, for each interface. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization. | ||||
| CsnNetFlowIfFlowSwitching | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.18.4.1.2 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory To enable/disable flow switching in a particular interface: disable (0) - no flow switching enable (1) - flow switching
| ||||
| NsnSFlow | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.19 | |||
| NsnSFlowGlb | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.19.1 | |||
| TsnSflowCollectorTable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.19.2 | NA | mandatory | |
table · not-accessible · mandatory Table of all but first sFlow collectors. The first collector can be configured using sFlowTable in RFC 3176. The RFC cannot be used to configure more than one sFlow collectors. This table has been created to fill this gap. | ||||
| RsnSflowCollectorEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.19.2.1 | NA | mandatory | |
| CsnSflowCollectorIndex | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.19.2.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The index to the sFlow collector table. | ||||
| CsnSflowCollectorIP | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.19.2.1.2 | IpAddress | RW | mandatory |
column · IpAddress · read-write · mandatory The sFlow collector ip address. | ||||
| CsnSflowCollectorUDPPort | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.19.2.1.3 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory The sFlow collector UDP port number. | ||||
| CsnSflowCollectorRowStatus | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.19.2.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory To create, update or delete a SFlow collector table entry. If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row other(1)....some other case valid(2)....the row exists and is valid
| ||||
| NsnFDP | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.20 | |||
| NsnFdpMIBObjects | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1 | |||
| NsnFdpInterface | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.1 | |||
| TsnFdpInterfaceTable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.1.1 | NA | mandatory | |
table · not-accessible · mandatory Status of FDP on the device's interfaces. | ||||
| RsnFdpInterfaceEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.1.1.1 | NA | mandatory | |
row · not-accessible · mandatory An entry in the snFdpInterfaceTable, having the status of FDP on an interface. | ||||
| CsnFdpInterfaceIfIndex | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.1.1.1.1 | INTEGER | NA | mandatory |
column · INTEGER · not-accessible · mandatory ifIndex value of the local interface. | ||||
| CsnFdpInterfaceFdpEnable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.1.1.1.2 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory The flag, whether the Foundry Discovery Protocol is currently running on this interface. It has no effect when FDP is disabled (snFdpGlobalRun = FALSE).
| ||||
| CsnFdpInterfaceCdpEnable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.1.1.1.3 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory The flag, whether the Cisco Discovery Protocol is currently running on this interface. It has no effect when CDP is disabled (snCdpGlobalRun = FALSE).
| ||||
| NsnFdpCache | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.2 | |||
| TsnFdpCacheTable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.2.1 | NA | mandatory | |
table · not-accessible · mandatory The table for the cached information obtained via receiving FDP/CDP messages. | ||||
| RsnFdpCacheEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.2.1.1 | NA | mandatory | |
row · not-accessible · mandatory An entry in the snFdpCacheTable, having the information received via FDP/CDP on one interface from one device. Entries appear when a FDP/CDP advertisement is received from a neighbor device. Entries disappear when FDP/CDP is disabled on the interface, or globally. | ||||
| CsnFdpCacheIfIndex | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.2.1.1.1 | INTEGER | NA | mandatory |
column · INTEGER · not-accessible · mandatory ifIndex value of the local interface. | ||||
| CsnFdpCacheDeviceIndex | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.2.1.1.2 | INTEGER | NA | mandatory |
column · INTEGER · not-accessible · mandatory Identification of a device, which sent FDP/CDP messages | ||||
| CsnFdpCacheDeviceId | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.2.1.1.3 | DisplayString | RO | mandatory |
column · DisplayString · read-only · mandatory The Device-ID string as reported in the most recent FDP/CDP message. The zero-length string indicates no Device-ID field (TLV) was reported in the most recent FDP/CDP message. | ||||
| CsnFdpCacheAddressType | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.2.1.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory An indication of the type of address contained in the corresponding instance of snFdpCacheAddress.
| ||||
| CsnFdpCacheAddress | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.2.1.1.5 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The (first) network-layer address of the device
as reported in the most recent FDP/CDP message
in the following format:
IP address: 4 octets, ip(1)
IPX address: 10 octets, ipx(2)
First 4-octet as the network number
Second 6-octet as the host number
Appletalk address: 3 octets, appletalk(3)
First 2-octet as the network number
Second 1-octet as the host number | ||||
| CsnFdpCacheVersion | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.2.1.1.6 | DisplayString | RO | mandatory |
column · DisplayString · read-only · mandatory Version string as reported in the most recent FDP/CDP message. | ||||
| CsnFdpCacheDevicePort | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.2.1.1.7 | DisplayString | RO | mandatory |
column · DisplayString · read-only · mandatory The Port-ID string as reported in the most recent FDP/CDP message. This will typically be the value of the ifName object (e.g., Ethernet0). The zero-length string indicates no Port-ID field (TLV) was reported in the most recent FDP/CDP message. | ||||
| CsnFdpCachePlatform | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.2.1.1.8 | DisplayString | RO | mandatory |
column · DisplayString · read-only · mandatory The Device's Hardware Platform as reported in the most recent FDP/CDP message. The zero-length string indicates that no Platform field (TLV) was reported in the most recent FDP/CDP message. | ||||
| CsnFdpCacheCapabilities | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.2.1.1.9 | DisplayString | RO | mandatory |
column · DisplayString · read-only · mandatory The Device's Functional Capabilities as reported in the most recent FDP/CDP message. | ||||
| CsnFdpCacheVendorId | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.2.1.1.10 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Indicates the entry received by either FDP or CDP.
| ||||
| CsnFdpCacheIsAggregateVlan | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.2.1.1.11 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Neighbor device is in aggregated-vlan.
| ||||
| CsnFdpCacheTagType | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.2.1.1.12 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Neighbor device tag-type. | ||||
| CsnFdpCachePortVlanMask | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.2.1.1.13 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory Neighbor device port VLAN masks in 512-byte octet string. | ||||
| CsnFdpCachePortTagMode | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.2.1.1.14 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Neighbor device port tag mode
| ||||
| CsnFdpCacheDefaultTrafficeVlanIdForDualMode | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.2.1.1.15 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Default traffic vlan id for neighbor device dual-mode port | ||||
| NsnFdpGlobal | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.3 | |||
| SsnFdpGlobalRun | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.3.1 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory The flag, whether the Foundry Discovery Protocol is currently running. FDP entries in snFdpCacheTable are deleted when FDP is disabled.
| ||||
| SsnFdpGlobalMessageInterval | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.3.2 | INTEGER (5..900) | RW | mandatory |
scalar · INTEGER (5..900) · read-write · mandatory The interval at which FDP messages are to be generated. The default value is 60 seconds. | ||||
| SsnFdpGlobalHoldTime | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.3.3 | INTEGER (10..255) | RW | mandatory |
scalar · INTEGER (10..255) · read-write · mandatory The time for the receiving device holds FDP message. The default value is 180 seconds. | ||||
| SsnFdpGlobalCdpRun | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.3.4 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory An indication of whether the Cisco Discovery Protocol is currently running. CDP entries in snFdpCacheTable are deleted when CDP is disabled.
| ||||
| NsnFdpCachedAddr | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.4 | |||
| TsnFdpCachedAddressTable | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.4.1 | NA | mandatory | |
table · not-accessible · mandatory Cached address table from receiving FDP/CDP messages. | ||||
| RsnFdpCachedAddressEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.4.1.1 | NA | mandatory | |
row · not-accessible · mandatory An entry (conceptual row) in the snFdpCacheAddressTable, containing one cached address from FDP/CDP messages. | ||||
| CsnFdpCachedAddrIfIndex | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.4.1.1.1 | INTEGER | NA | mandatory |
column · INTEGER · not-accessible · mandatory The ifIndex value of the local interface. | ||||
| CsnFdpCachedAddrDeviceIndex | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.4.1.1.2 | INTEGER | NA | mandatory |
column · INTEGER · not-accessible · mandatory A unique vlaue for each device from which FDP/CDP messages are being received. | ||||
| CsnFdpCachedAddrDeviceAddrEntryIndex | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.4.1.1.3 | INTEGER | NA | mandatory |
column · INTEGER · not-accessible · mandatory A unique vlaue for address entry in device from which FDP/CDP messages are being received. | ||||
| CsnFdpCachedAddrType | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.4.1.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory An indication of the type of address contained in the corresponding instance of snFdpCacheAddrValue.
| ||||
| CsnFdpCachedAddrValue | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.20.1.4.1.1.5 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The network-layer address of the device
SNMP-agent as reported in the most recent FDP/CDP message
in the following format:
IP address: 4 octets, ip(1)
IPX address: 10 octets, ipx(2)
First 4-octet as the network number
Second 6-octet as the host number
Appletalk address: 3 octets, appletalk(3)
First 2-octet as the network number
Second 1-octet as the host number | ||||
| NsnVsrp | 1.3.6.1.4.1.11.2.3.7.11.12.1.3.21 | |||