MIB Browser

HP-SN-MPLS-TC-MIB

Hewlett-Packard
This MIB module defines Textual Conventions and
OBJECT-IDENTITIES for use in documents defining
management information bases (MIBs) for managing
MPLS networks.
Organization
Multiprotocol Label Switching (MPLS) Working Group
Root OID
1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.1
Last updated
Objects
2
Source
Show full MIB
snmptranslate -m HP-SN-MPLS-TC-MIB -Tp
snmpwalk -v2c -c <community> -m HP-SN-MPLS-TC-MIB <host> 1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.1

Imports

HP-SN-ROOT-MIBsnMpls
SNMPv2-CONFMODULE-COMPLIANCE, NOTIFICATION-GROUP
SNMPv2-SMIBits, Integer32, IpAddress, MODULE-IDENTITY, MibIdentifier, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, iso, transmission
SNMPv2-TCDisplayString, PhysAddress, TEXTUAL-CONVENTION

OID tree

NameOIDTypeAccessStatus
NmplsMIB1.3.6.1.4.1.11.2.3.7.11.12.2.15.15
ImplsTCMIB1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.1

Textual conventions

MplsAtmVcIdentifier Integer32 (32..65535)
The VCI value for a VCL. The maximum VCI value
cannot exceed the value allowable by
atmInterfaceMaxVciBits defined in ATM-MIB. The
minimum value is 32, values 0 to 31 are reserved
for other uses by the ITU and ATM Forum.  32 is
typically the  default value for the Control VC.
MplsBitRate Integer32 (1..2147483647)

Display hint: d

An estimate of bandwidth in units of 1,000 bits per
second.  If this object reports a value of 'n' then
the rate of the object is somewhere in the range of
'n-500' to 'n+499'. For objects which do not vary
in bit rate, or for those where no accurate
estimation can be made, this object should contain
the nominal bit rate.
MplsBurstSize Unsigned32 (1..4294967295)

Display hint: d

The number of octets of MPLS data that the stream
may send back-to-back without concern for
policing.
MplsExtendedTunnelId Unsigned32
A unique identifier for an MPLS Tunnel. This MAY
represent an IpV4 address of the ingress or egress
LSR for the tunnel. This value is derived from the
Extended Tunnel Id in RSVP or the Ingress Router ID
for CR-LDP.
MplsInitialCreationSource INTEGER

crldp(5) ldp(3) other(1) policyAgent(6) rsvp(4) snmp(2) unknown(7)

The entity that originally created the object in
 question. The values of this enumeration are
 defined as follows:

other(1) - This is used when an entity which has not
 been enumerated in this textual convention but
 which is known by the agent.

snmp(2) - The Simple Network Management Protocol was
 used to configure this object initially.

ldp(3 - The Label Distribution Protocol was used to
 configure this object initially.

rsvp(4) - The Resource Reservation Protocol was used
 to configure this object initially.

crldp(5) - The Constraint-Based Label Distribution
 Protocol was used to configure this object
 initially.

policyAgent(6) - A policy agent (perhaps in
 combination with one of the above protocols) was
 used to configure this object initially.

unknown(7) - the agent cannot discern which
 component created the object.
MplsLSPID OCTET STRING (SIZE (0..31))
An identifier that is assigned to each LSP and is
used to uniquely identify it.  This is assigned at
the head end of the LSP and can be used by all LSRs
to identify this LSP.  This value is piggybacked by
the signaling protocol when this LSP is signaled
within the network.  This identifier can then be
used at each LSR to identify which labels are being
swapped to other labels for this LSP.  For IPv4
addresses this results in a 6-octet long cookie.
MplsLabel Unsigned32 (0..4294967295)
This value represents an MPLS label as defined in
[RFC3031],  [RFC3032], [RFC3034] and [RFC3035].
MplsLdpGenAddr OCTET STRING (SIZE (0..64))
The value of an network layer or data link layer
address.
MplsLdpIdentifier OCTET STRING (SIZE (6))
The LDP identifier is a six octet quantity which is
 used to identify an Label Switch Router (LSR) label
 space.

The first four octets identify the LSR and must be a
 globally unique value, such as a 32-bit router ID
 assigned to the LSR, and the last two octets
 identify a specific label space within the LSR.
MplsLdpLabelTypes INTEGER

atm(2) frameRelay(3) generic(1)

The Layer 2 label types which are defined for MPLS
LDP/CRLDP are generic(1), atm(2), or
frameRelay(3).
MplsLsrIdentifier OCTET STRING (SIZE (4))
The Label Switch Router (LSR) identifier is the
first 4 bytes of the Label Distribution Protocol
(LDP) identifier.
MplsPathIndex Unsigned32
A unique identifier used to identify a specific path
used by a tunnel.
MplsPathIndexOrZero Unsigned32
A unique identifier used to identify a specific path
used by a tunnel. If this value is set to 0, it
indicates that no path is in use.
MplsPortNumber Integer32 (0..65535)
A TCP or UDP port number. Along with an IP address
identifies a stream of IP traffic uniquely.
MplsTunnelAffinity Unsigned32
Include-any, include-all, or exclude-all constraint
for link selection.
MplsTunnelIndex Integer32 (1..65535)
Index into mplsTunnelTable.
MplsTunnelInstanceIndex Unsigned32 (0..65535)
Instance index into mplsTunnelTable.

Used by