HP-SN-AGENT-MIB
Hewlett-Packardsnmptranslate -m HP-SN-AGENT-MIB -Tpsnmpwalk -v2c -c <community> -m HP-SN-AGENT-MIB <host> 1.3.6.1.4.1.11.2.3.7.11.12.1.1.1Imports
| HP-SN-ROOT-MIB | snAgentSys, snChassis, snStack |
|---|---|
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP |
| SNMPv2-SMI | Bits, Counter32, Gauge32, Integer32, IpAddress, MODULE-IDENTITY, MibIdentifier, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, iso |
| SNMPv2-TC | DisplayString, PhysAddress, TEXTUAL-CONVENTION |
OID tree
| Name | OID | Type | Access | Status |
|---|---|---|---|---|
| NsnChasGen | 1.3.6.1.4.1.11.2.3.7.11.12.1.1.1 | |||
| SsnChasType | 1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.1 | DisplayString (SIZE (0..128)) | RO | mandatory |
scalar · DisplayString (SIZE (0..128)) · read-only · mandatory The chassis type represents the type of Foundry product being managed. | ||||
| SsnChasSerNum | 1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.2 | DisplayString (SIZE (0..128)) | RO | mandatory |
scalar · DisplayString (SIZE (0..128)) · read-only · mandatory The serial number of the chassis. If the serial number is unknown or unavailable then the value should be a zero length string. | ||||
| SsnChasPwrSupplyStatus | 1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.3 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory A bit array that contains the value of the
Chassis Power Supplies. This is a packed bit string;
the 2 power supplies status are encoded into 4 bits
(a nibble).
There are multiple power supplies per chassis in this release.
The following shows the meaning of each bit:
(bit 0 is the least significant bit).
bit position meaning
------------ -------
12-31 reserved
11 Power Supply 4 DC (0=bad, 1=good).
10 Power Supply 3 DC (0=bad, 1=good).
9 Power Supply 4 present status (0=present, 1=not-present).
8 Power Supply 3 present status (0=present, 1=not-present).
4-7 reserved
3 Power Supply 2 DC (0=bad, 1=good).
2 Power Supply 1 DC (0=bad, 1=good).
1 Power Supply 2 present status (0=present, 1=not-present).
0 Power Supply 1 present status (0=present, 1=not-present). | ||||
| SsnChasFanStatus | 1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.4 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory A bit array that contains the value of the
fan status. This is a packed bit string. The
status of each fan is encoded into one bit.
bit value meaning
--------- -------
0 fan failure.
1 fan good.
There are two fans per VLAN Switch chassis in this release.
The following shows the meaning of each bit:
(bit 0 is the least significant bit).
bit position meaning
------------ -------
4-31 reserved
3 fan4 status
2 fan3 status
1 fan2 status
0 fan1 status | ||||
| SsnChasMainBrdDescription | 1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.5 | DisplayString (SIZE (0..128)) | RO | mandatory |
scalar · DisplayString (SIZE (0..128)) · read-only · mandatory The main board description string. (It is obsoleted for Chassis Product) | ||||
| SsnChasMainPortTotal | 1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.6 | INTEGER (1..24) | RO | mandatory |
scalar · INTEGER (1..24) · read-only · mandatory The total number of ports for the main board. (It is obsoleted for Chassis Product) | ||||
| SsnChasExpBrdDescription | 1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.7 | DisplayString (SIZE (0..128)) | RO | mandatory |
scalar · DisplayString (SIZE (0..128)) · read-only · mandatory The expansion board description string. Expansion board are those boards attaching on the main board. (It is obsoleted for Chassis Product) | ||||
| SsnChasExpPortTotal | 1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.8 | INTEGER (1..24) | RO | mandatory |
scalar · INTEGER (1..24) · read-only · mandatory The total number of ports for the expansion board. (It is obsoleted for Chassis Product) | ||||
| SsnChasStatusLeds | 1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.9 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory A bit array that contains the value of the
front panel status LEDs. This is a bit-map;
each LED is encoded into 1 bit for each switch
port. The maximum number of ports in one chassis
is 24 that means 24 Ports Status LEDs. The expansion port
number always begins from the last main port number.
The following shows the meaning of each bit for each
switch port:
bit value meaning
-------- ---------
0 off (Link off)
1 on (Link on)
The bitmap of LEDs are as following:
(Port1) (Port4) (Port8)
Bit (Bit0) (Bit3) (Bit7)
Byte 1: LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8
Byte 2: LED9 LED10 LED11 LED12 LED13 LED14 LED15 LED16
Byte 3: LED17 LED18 LED19 LED20 LED21 LED22 LED23 LED24
-------- | ||||
| SsnChasTrafficLeds | 1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.10 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory A bit array that contains the value of the
front panel traffic LEDs. This is a packed bit string;
each LED is encoded into 1 bit for each switch
port. The maximum number of ports in one chassis
is 24 that means 24 Ports Traffic LEDs. The expansion port
number always begins from the last main port number.
The following shows the meaning of each bit for each
switch port:
bit value meaning
-------- ---------
0 off (no traffic)
1 on (traffic)
The bitmap of LEDs are as following:
(Port1) (Port4) (Port8)
Bit (Bit0) (Bit3) (Bit7)
Byte 1: LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8
Byte 2: LED9 LED10 LED11 LED12 LED13 LED14 LED15 LED16
Byte 3: LED17 LED18 LED19 LED20 LED21 LED22 LED23 LED24
-------- | ||||
| SsnChasMediaLeds | 1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.11 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory A bit array that contains the value of the
front panel media LEDs. This is a packed bit string;
each LED is encoded into 1 bit for each switch port.
The maximum number of ports in one chassis is 24
that means 24 Ports Media LEDs. The expansion port
number always begins from the last main port number.
The following shows the meaning of each bit for each
switch port:
bit value meaning
--------- -------
0 half duplex
1 full duplex
The bitmap of LEDs are as following:
(Port1) (Port4) (Port8)
Bit (Bit0) (Bit3) (Bit7)
Byte 1: LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8
Byte 2: LED9 LED10 LED11 LED12 LED13 LED14 LED15 LED16
Byte 3: LED17 LED18 LED19 LED20 LED21 LED22 LED23 LED24
--------- | ||||
| SsnChasEnablePwrSupplyTrap | 1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.12 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Indicates whether the SNMP agent process is permitted to generate power supply failure traps.
| ||||
| SsnChasMainBrdId | 1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.13 | OCTET STRING | RO | mandatory |
scalar · OCTET STRING · read-only · mandatory The main board identifier, which can uniquely identify a board
type. It is an encoded octet string with the following meaning:
octet 0 - octet string format version, which identifies the
format of this string.
If format version octet has the value 1, the octets after the
version octet have the following meaning:
octet 1 - product type, FIWG=0x57, FIBB=0x42, FIMLS=0x4D
NI=0x4E, TI=0x54, TIRT=0x52
octet 2 - board type, POWERPC=1, ALPHA=2
The length of the octet string is 27.
If format version octet has the value 2, the octets after the
version octet have the following meaning:
octet 1 - product type:
BI_WG 0x57
BI_BB 0x42
BI_NI 0x4E
octet 2 - module type:
FI_MASTER_FIBER_8G 0x7
FI_MASTER_FIBER_4G 0x5
FI_MASTER_FIBER_2G 0x4
FI_SLAVE_COPPER_24 0xB
MASTER_FIBER_8G 0x0
MASTER_FIBER_4G 0x1
MASTER_FIBER_2G 0x12
MASTER_FIBER_0G 0x14
MASTER_COPPER_16 0x2
MASTER_COPPER_8G 0x6
MASTER_COPPER_12_2 0x9
SLAVE_FIBER_8G 0x8
SLAVE_FIBER_4G 0x3
SLAVE_COPPER_20 0xA
SLAVE_COPPER_24 0xA
SLAVE_100FX_8 0xD
SLAVE_100FX_16 0xC
SLAVE_COPPER_8G 0xE
SLAVE_COPPER_16_2 0xF
STACK_FIBER_8G 0x10
STACK_COPPER_8G 0x11
SLAVE_100FX_24 0x13
The length of the octet string is 28.
Both format version 1 and 2:
octet 3 - processor type, PVR_M603=3, PVR_M604=4, PVR_M603E=6,
PVR_M603EV=7, PVR_M604E=9
octet 4 to
octet 5 - processor speed in MHz
octet 6 - MAC type:
MAC_SEEQ_10_100=1,
MAC_DEC_10_100=2,
MAC_SEEQ_1000=5,
MAC_GMAC_1000=6,
MAC_VLSI_1000=9
octet 7 - PHY type, PHY_NONE=0, PHY_QSI=1, PHY_ICS=3,
PHY_NATIONAL=4, PHY_LEVEL1=6, PHY_LEVEL16=7,
PHY_LEVEL24=8
octet 8 - port type, COPPER=0, FIBER=1
octet 9 - fiber port type, NONFIBER=0, SX_FIBER=1,
LX_FIBER=2, LHX_FIBER=3, LX_SX_FIBER=4,
LHB_FIBER=5
octet 10 to
octet 13 - DRAM size in KBytes
octet 14 to
octet 17 - boot flash size in KBytes
octet 18 to
octet 21 - code flash size in KBytes
octet 22 to
octet 27 - serial number.
Format version 1 only:
octet 28 - chassis backplane type.
chassis4000 = 0x00
chassis8000 = 0x04
Turbo8 = 0x07 (stack2)
FastIron2 = 0x06 (stack1) | ||||
| SsnChasExpBrdId | 1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.14 | OCTET STRING | RO | mandatory |
scalar · OCTET STRING · read-only · mandatory The expansion board identifier. Expansion board are those
boards attaching on the main board. It is an encoded octet
string with the following meaning:
octet 0 - octet string format version, which identifies
the format of this string.
If format version octet has the value 1, the octets after
the version octet have the following meaning:
octet 1 - expansion board type, HUNDRED_MEG_1PORT=1,
HUNDRED_MEG_2PORT=2, HUNDRED_MEG_1PORT_COPPER=3,
HUNDRED_MEG_2PORT_COPPER=4, HUNDRED_MEG_2PORT_LX=5,
GIGA_1PORT=8, GIGA_2PORT=9
octet 2 - fiber port type, NONFIBER=0, SX_FIBER=1,
LX_FIBER=2, LHX_FIBER=3, LX_SX_FIBER=4
(It is obsoleted for Chassis Product) | ||||
| SsnChasSpeedLeds | 1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.15 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory A bit array that contains the value of the
front panel media LEDs. This is a packed bit string;
each LED is encoded into 1 bit for each switch port.
The maximum number of ports in one chassis is 24
that means 24 Ports Speed LEDs. The expansion port
number always begins from the last main port number.
The following shows the meaning of each bit for each
switch port:
bit value meaning
--------- -------
0 10 MBit
1 100 MBit
The bitmap of LEDs are as following:
(Port1) (Port4) (Port8)
Bit (Bit0) (Bit3) (Bit7)
Byte 1: LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8
Byte 2: LED9 LED10 LED11 LED12 LED13 LED14 LED15 LED16
Byte 3: LED17 LED18 LED19 LED20 LED21 LED22 LED23 LED24
--------- | ||||
| SsnChasEnableFanTrap | 1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.16 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Indicates whether the SNMP agent process is permitted to generate fan failure traps.
| ||||
| SsnChasIdNumber | 1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.17 | DisplayString (SIZE (0..64)) | RW | mandatory |
scalar · DisplayString (SIZE (0..64)) · read-write · mandatory An administratively-assigned chassis identity number, used by inventory control. | ||||
| SsnChasActualTemperature | 1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.18 | INTEGER (-110..250) | RO | mandatory |
scalar · INTEGER (-110..250) · read-only · mandatory Temperature of the chassis. Each unit is 0.5 degrees Celcius. Only management module built with temperature sensor hardware is applicable. For those non-applicable management module, it returns no-such-name. | ||||
| SsnChasWarningTemperature | 1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.19 | INTEGER (0..250) | RW | mandatory |
scalar · INTEGER (0..250) · read-write · mandatory Actual temperature higher than this threshold value will trigger the switch to send a temperature warning trap. Each unit is 0.5 degrees Celcius. Only management module built with temperature sensor hardware is applicable. For those non-applicable management module, it returns no-such-name. | ||||
| SsnChasShutdownTemperature | 1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.20 | INTEGER (0..250) | RW | mandatory |
scalar · INTEGER (0..250) · read-write · mandatory Actual temperature higher than this threshold value will shutdown a partial of the switch hardware to cool down the system. Each unit is 0.5 degrees Celcius. Only management module built with temperature sensor hardware is applicable. For those non-applicable management module, it returns no-such-name. | ||||
| SsnChasEnableTempWarnTrap | 1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.21 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Indicates whether the SNMP agent process is permitted to generate temperature warning traps.
| ||||
| NsnChasPwr | 1.3.6.1.4.1.11.2.3.7.11.12.1.1.2 | |||
| TsnChasPwrSupplyTable | 1.3.6.1.4.1.11.2.3.7.11.12.1.1.2.1 | NA | mandatory | |
table · not-accessible · mandatory A table of each power supply information. Only installed power supply appears in a table row. | ||||
| RsnChasPwrSupplyEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.1.2.1.1 | NA | mandatory | |
| CsnChasPwrSupplyIndex | 1.3.6.1.4.1.11.2.3.7.11.12.1.1.2.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The index to power supply table. | ||||
| CsnChasPwrSupplyDescription | 1.3.6.1.4.1.11.2.3.7.11.12.1.1.2.1.1.2 | DisplayString (SIZE (0..128)) | RO | mandatory |
column · DisplayString (SIZE (0..128)) · read-only · mandatory The power supply description string. | ||||
| CsnChasPwrSupplyOperStatus | 1.3.6.1.4.1.11.2.3.7.11.12.1.1.2.1.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The power supply operation status.
| ||||
| NsnChasFan | 1.3.6.1.4.1.11.2.3.7.11.12.1.1.3 | |||
| TsnChasFanTable | 1.3.6.1.4.1.11.2.3.7.11.12.1.1.3.1 | NA | mandatory | |
table · not-accessible · mandatory A table of each fan information. Only installed fan appears in a table row. | ||||
| RsnChasFanEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.1.3.1.1 | NA | mandatory | |
| CsnChasFanIndex | 1.3.6.1.4.1.11.2.3.7.11.12.1.1.3.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The index to fan table. | ||||
| CsnChasFanDescription | 1.3.6.1.4.1.11.2.3.7.11.12.1.1.3.1.1.2 | DisplayString (SIZE (0..128)) | RO | mandatory |
column · DisplayString (SIZE (0..128)) · read-only · mandatory The fan description string. | ||||
| CsnChasFanOperStatus | 1.3.6.1.4.1.11.2.3.7.11.12.1.1.3.1.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The fan operation status.
| ||||
| NsnAgentGbl | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.1 | |||
| SsnAgReload | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.1 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Action object to reboot the agent. The following values can only be read: other(1).....agent in unknown or other state running(2)...agent running The following value can be written: reset(3).....do a hard reset The agent will return a response before the action occurs.
| ||||
| SsnAgEraseNVRAM | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.2 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Action object to erase NVRAM of the agent. The following values can only be read: normal(1) error(2)... operation failed or bad flash erasing(4)...agent is erasing NVRAM flash The following value can be written: erase(3).....do erase The agent will return a response even before the erase is done. And the read value will be erasing until erase is done. And the erase request will be rejected until error or normal.
| ||||
| SsnAgWriteNVRAM | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.3 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Action object to save all configuration info to NVRAM of the agent. The following values can only be read: normal(1) error(2)... operation failed or bad flash writing(4)...agent is writing NVRAM flash The following value can be written: write(3).....do write The agent will return a response even before the write is done. And the read value will be writing until write is done. And the write request will be rejected until error or normal.
| ||||
| SsnAgConfigFromNVRAM | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.4 | INTEGER | NA | mandatory |
scalar · INTEGER · not-accessible · mandatory Action object to config the switch from NVRAM of the agent. The following values can only be read: normal(1) error(2)... operation failed or bad flash configing(4)...configing from NVRAM flash is in process. The following value can be written: config(3).....do config The agent will return a response after config is done.
| ||||
| SsnAgTftpServerIp | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.5 | IpAddress | RW | mandatory |
scalar · IpAddress · read-write · mandatory The tftp server address, this will be used for both download/upload image file and config file. | ||||
| SsnAgImgFname | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.6 | DisplayString (SIZE (0..32)) | RW | mandatory |
scalar · DisplayString (SIZE (0..32)) · read-write · mandatory Name of the image file including path currently associated with the system. When the object is not used, the value is a zero length string. | ||||
| SsnAgImgLoad | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.7 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Action object to down/up load a new image to the agent. The following values: Error values: from normal(1) to operationError(17) and tftpWrongFileType(23). loading(18) .. operation is in process. The following values are used for set : uploadPrimary(19)..upload the Primary image from flash to tftp server. downloadPrimary(20)..download the Primary image from tftp server to flash. uploadSecondary(21)..upload the Secondary image from flash to tftp server. downloadSecondary(22)..download the Secondary image from tftp server to flash. The image filename is defined in snAgImgFname. The tftp server address is defined in snAgTftpServerIp. Atomic set of snAgImgLoad, snAgImgFname and snAgTftpServerIp is required to allow down/up load to happen. And the write request will be rejected during loading until error or normal.
| ||||
| SsnAgCfgFname | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.8 | DisplayString (SIZE (0..32)) | RW | mandatory |
scalar · DisplayString (SIZE (0..32)) · read-write · mandatory Name of the config file(s) including path currently associated with the system. Some agents in special situations may support a value which contains multiple file names instead of a single file name. Multiple names are specified as a list of file names separated by semicolons (;). When the object is not used, the value is a zero length string. | ||||
| SsnAgCfgLoad | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.9 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Action object to down/up load a config image
to the agent. The following values can be
read :
Error values: from normal(1) to operationError(17) and tftpWrongFileType(29).
loading(18) .. operation is in process.
The following value can be used to set:
uploadFromFlashToServer(20)..upload the config from flash
to tftp server.
downloadToFlashFromServer(21)..download the config to flash
from tftp server.
uploadFromDramToServer(22)..upload the config from DRAM
to tftp server.
downloadToDramFromServer(23)..download the config to DRAM
from tftp server.
The following value can be used to set:
uploadFromFlashToNMS(24)..upload the config from flash to NMS.
downloadToFlashFromNMS(25)..download the config to flash from NMS.
uploadFromDramToNMS(26)..upload the config from DRAM to NMS.
downloadToDramFromNMS(27)..download the config to DRAM from NMS.
The config filename is defined in
snAgCfgFname. The tftp server address is defined in snAgTftpServerIp.
Atomic set of snAgCfgLoad, snAgCfgFname and snAgTftpServerIp is
required to allow down/up load to happen. And the write request
will be rejected during loading until error or normal.
For those NMS commands from (24) to (27), The snAgCfgEosTable MIB must
be sent along in one PDU. A seperate write memory cli or set
snAgWriteNVRAM is required to save the config to NVRAM.
| ||||
| SsnAgDefGwayIp | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.10 | IpAddress | RW | mandatory |
scalar · IpAddress · read-write · mandatory The default gateway (router) address. | ||||
| SsnAgImgVer | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.11 | DisplayString (SIZE (0..32)) | RO | mandatory |
scalar · DisplayString (SIZE (0..32)) · read-only · mandatory The version of the running software in the form 'major.minor.maintenance[letters]'. | ||||
| SsnAgFlashImgVer | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.12 | DisplayString (SIZE (0..32)) | RO | mandatory |
scalar · DisplayString (SIZE (0..32)) · read-only · mandatory The version of the software image saved in local storage such as flash memory in the form 'major.minor.maintenance[letters]'. If not known or not available, then the value is a zero length string. | ||||
| SsnAgGblIfIpAddr | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.13 | IpAddress | RW | mandatory |
scalar · IpAddress · read-write · mandatory The interface ip address. | ||||
| SsnAgGblIfIpMask | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.14 | IpAddress | RW | mandatory |
scalar · IpAddress · read-write · mandatory The interface ip address mask. | ||||
| SsnAgGblPassword | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.15 | DisplayString (SIZE (0..48)) | RW | mandatory |
scalar · DisplayString (SIZE (0..48)) · read-write · mandatory System Security Access Password and this is only allowed to use for setting but not for reading. An SNMP-Get will get an zero string. | ||||
| SsnAgTrpRcvrCurEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.16 | INTEGER (0..255) | RO | mandatory |
scalar · INTEGER (0..255) · read-only · mandatory The current total entries of the Trap Receiver Table are created. | ||||
| SsnAgGblDataRetrieveMode | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.19 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory By default, this mode is set to nextbootCfg(0). The VLAN Table and Port-STP Table data will be retrieved according to this mode. nextbootCfg(0).........the nextboot configuration data are retrieved operationalData(1)..........the current running data are retrieved
| ||||
| SsnAgSystemLog | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.20 | OCTET STRING (SIZE (5)) | RW | mandatory |
scalar · OCTET STRING (SIZE (5)) · read-write · mandatory The system log object to indicate whether any Network
Management Station(NMS) has login. The first byte
of the octet string is the value decribed below and
followed by 4 bytes of secret code.
login(1)..... a value for a NMS to login.
heartbeat(2)... a value for the login NMS periodically to
checkin; Otherwise, the Agent will automatically
set this object to logout(3) after a timeout
period.
logout(3).... a value for a NMS to logout.
changePassword(4).... a value for the login NMS to change
password, only if snAgGblPasswordChangeMode
was configured to 'anyMgmtEntity'.
changeReadOnlyCommunity(5).... a value for the login NMS
to change the read-only community string,
only if snAgGblPasswordChangeMode was
configured to 'anyMgmtEntity'.
changeReadWriteCommunity(6).... a value for the login NMS
to change the read-write community string,
only if snAgGblPasswordChangeMode was
configured to 'anyMgmtEntity'. | ||||
| SsnAgGblEnableColdStartTrap | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.21 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Indicates whether the SNMP agent process is permitted to generate cold start traps.
| ||||
| SsnAgGblEnableLinkUpTrap | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.22 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Indicates whether the SNMP agent process is permitted to generate link up traps.
| ||||
| SsnAgGblEnableLinkDownTrap | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.23 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Indicates whether the SNMP agent process is permitted to generate link down traps.
| ||||
| SsnAgGblPasswordChangeMode | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.24 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory Specify which management entity is allowed to change the password. 'anyMgmtEntity' management entities are SNMP management station, console command line interface, and telnet command line interface. For security reason, this object can only be modified by console command line interface or telnet command line interface. The default value is 'consoleAndTelnet', of which both console and telnet command line interfaces are allowed to change the password.
| ||||
| SsnAgGblReadOnlyCommunity | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.25 | DisplayString (SIZE (0..32)) | RW | mandatory |
scalar · DisplayString (SIZE (0..32)) · read-write · mandatory SNMP read community string and this is only allowed to use for setting but not for reading. An SNMP-Get will get an zero length string. | ||||
| SsnAgGblReadWriteCommunity | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.26 | DisplayString (SIZE (0..32)) | RW | mandatory |
scalar · DisplayString (SIZE (0..32)) · read-write · mandatory SNMP read-write community string and this is only allowed to use for setting but not for reading. An SNMP-Get will get an zero length string. | ||||
| SsnAgGblCurrentSecurityLevel | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.27 | INTEGER (0..5) | RO | mandatory |
scalar · INTEGER (0..5) · read-only · mandatory This represnts the current log-in security level. Each level of security requires a password to permit user for different system configurations. | ||||
| SsnAgGblSecurityLevelSet | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.28 | INTEGER (0..5) | RW | mandatory |
scalar · INTEGER (0..5) · read-write · mandatory This shows which the security level password to be set. | ||||
| SsnAgGblLevelPasswordsMask | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.29 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory This shows the bitmap of level passwords which successfully assigned to the system. | ||||
| SsnAgGblQueueOverflow | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.30 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory false - The device queues are not overflow. true - The device queues are overflow.
| ||||
| SsnAgGblBufferShortage | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.31 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory false - The device buffers are adequate. true - The device buffers are in shortage.
| ||||
| SsnAgGblDmaFailure | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.32 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory false - The device DMAs are in good condition. true - One of the DMAs in the device fails.
| ||||
| SsnAgGblResourceLowWarning | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.33 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory false - No, the device does not have resource-low-warning. true - Yes, the device does have resource-low-warning.
| ||||
| SsnAgGblExcessiveErrorWarning | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.34 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory false - No, the device does not have any excessive collision, FCS errors, alignment warning etc. true - Yes, the device does have.
| ||||
| SsnAgGblCpuUtilData | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.35 | Gauge | RO | mandatory |
scalar · Gauge · read-only · mandatory The statistics collection of utilization of the CPU in the device. | ||||
| SsnAgGblCpuUtilCollect | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.36 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory enable(1) - The beginning of statistics collection of utilization of the CPU in the device. disable(0) - The end of statistics collection of utilization of the CPU in the device.
| ||||
| SsnAgGblTelnetTimeout | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.37 | INTEGER (0..240) | RW | mandatory |
scalar · INTEGER (0..240) · read-write · mandatory Telnet session idling timeout value. Writing value 0 to this object never timeouts any telnet sessions. Each value unit is one minute. | ||||
| SsnAgGblEnableWebMgmt | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.38 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Enable/disable web management.
| ||||
| SsnAgGblSecurityLevelBinding | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.39 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory This represnts the binding of a given password to which security level. A value of 255 indicates an invalid binding. | ||||
| SsnAgGblEnableSLB | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.40 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory Enable/disable Server Load Balancing.
| ||||
| SsnAgSoftwareFeature | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.41 | OCTET STRING | RO | mandatory |
scalar · OCTET STRING · read-only · mandatory A bit string representing the software feature of the running switch/router image. These features were conditional compiled to different product images. For each bit, exist feature has a value of 1, but non-exist feature has a value of 0. octet 0, bit 0 - RMON octet 0, bit 1 - ipx switching octet 0, bit 2 - server load balancing octet 0, bit 3 - layer 3 filter in switch octet 0, bit 4 - ipx routing octet 0, bit 5 - appletalk routing octet 0, bit 6 - ip multicast routing octet 0, bit 7 - local access control octet 1, bit 0 - BGP routing octet 1, bit 1 - loopback interface octet 1, bit 2 - BigIron multi-management module octet 1, bit 3 - BigIron SYSIF II octet 1, bit 4 - BigIron POS support octet 1, bit 5 - appletalk cable vlan octet 1, bit 6 - 64 subnet octet 1, bit 7 - multi-slot trunk octet 2, bit 0 - TACACS octet 2, bit 1 - Gigabit Ethernet port auto-negotiation mode octet 2, bit 2 - FSRP octet 2, bit 3 - Exodus requested OSPF enhancement octet 2, bit 4 - OSPF NSSA octet 2, bit 5 - POS octet 2, bit 6 - QOS octet 2, bit 7 - Single Span octet 3, bit 0 - Fast Span octet 3, bit 1 - Base L3 octet 3, bit 2 - static log buffer Bit 0 is the least significant bit of an octet, and bit 7 is the most significant bit of an octet. | ||||
| SsnAgGblEnableModuleInsertedTrap | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.42 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Indicates whether the SNMP agent process is permitted to generate hardware module inserted to chassis traps.
| ||||
| SsnAgGblEnableModuleRemovedTrap | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.43 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Indicates whether the SNMP agent process is permitted to generate hardware module removed from chassis traps.
| ||||
| SsnAgGblTrapMessage | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.44 | DisplayString | RO | mandatory |
scalar · DisplayString · read-only · mandatory A generic trap message string. | ||||
| SsnAgGblEnableTelnetServer | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.45 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Enable or disable telnet server in device.
| ||||
| SsnAgGblTelnetPassword | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.46 | DisplayString (SIZE (0..48)) | RW | mandatory |
scalar · DisplayString (SIZE (0..48)) · read-write · mandatory Telnet Access Password and this is only allowed to use for setting but not for reading. An SNMP-Get will get an zero string. | ||||
| SsnAgBuildDate | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.47 | DisplayString (SIZE (0..32)) | RO | mandatory |
scalar · DisplayString (SIZE (0..32)) · read-only · mandatory The date of the built software. | ||||
| SsnAgBuildtime | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.48 | DisplayString (SIZE (0..32)) | RO | mandatory |
scalar · DisplayString (SIZE (0..32)) · read-only · mandatory The time of the built software. | ||||
| SsnAgBuildVer | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.49 | DisplayString (SIZE (0..32)) | RO | mandatory |
scalar · DisplayString (SIZE (0..32)) · read-only · mandatory The version of the built software in the form 'major.minor.maintenance[letters]'. | ||||
| NsnAgentBrd | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.2 | |||
| TsnAgentBrdTable | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1 | NA | mandatory | |
table · not-accessible · mandatory A table of each physical board information. | ||||
| RsnAgentBrdEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1 | NA | mandatory | |
| CsnAgentBrdIndex | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.1 | INTEGER (1..8) | RO | mandatory |
column · INTEGER (1..8) · read-only · mandatory The index to the Agent Interface Table. | ||||
| CsnAgentBrdMainBrdDescription | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.2 | DisplayString (SIZE (0..128)) | RO | mandatory |
column · DisplayString (SIZE (0..128)) · read-only · mandatory The main board description string. | ||||
| CsnAgentBrdMainBrdId | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.3 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The main board identifier, which can uniquely identify a board
type. It is an encoded octet string with the following meaning:
octet 0 - octet string format version, which identifies the
format of this string.
If format version octet has the value 2, the octets after the
version octet have the following meaning:
octet 1 - product type:
BI_WG 0x57
BI_BB 0x42
BI_NI 0x4E
octet 2 - module type:
MASTER_FIBER_8G 0x0
MASTER_FIBER_4G 0x1
MASTER_FIBER_2G 0x12
MASTER_FIBER_0G 0x14
MASTER_COPPER_16 0x2
MASTER_COPPER_8G 0x6
MASTER_COPPER_12_2 0x9
SLAVE_FIBER_8G 0x8
SLAVE_FIBER_4G 0x3
SLAVE_FIBER_2G 0x17
SLAVE_COPPER_8G 0xE
SLAVE_COPPER_2G 0x18
SLAVE_COPPER_16_2 0xF
SLAVE_COPPER_20 0xA
SLAVE_COPPER_24 0xA
SLAVE_100FX_8 0xD
SLAVE_100FX_16 0xC
SLAVE_100FX_24 0x13
STACK_FIBER_8G 0x10
STACK_COPPER_8G 0x11
POS_622M 0x15
POS_155M 0x16
octet 3 - processor type, PVR_M603=3, PVR_M604=4, PVR_M603E=6,
PVR_M603EV=7, PVR_M604E=9
octet 4 to
octet 5 - processor speed in MHz
octet 6 - MAC type:
MAC_SEEQ_10_100=1,
MAC_DEC_10_100=2,
MAC_SEEQ_1000=5,
MAC_GMAC_1000=6,
MAC_VLSI_1000=9
octet 7 - PHY type, PHY_NONE=0, PHY_QSI=1, PHY_ICS=3,
PHY_NATIONAL=4, PHY_LEVEL1=6, PHY_LEVEL16=7,
PHY_LEVEL24=8
octet 8 - port type, COPPER=0, FIBER=1
octet 9 - fiber port type, NONFIBER=0, SX_FIBER=1,
LX_FIBER=2, LHX_FIBER=3
octet 10 to
octet 13 - DRAM size in KBytes
octet 14 to
octet 17 - boot flash size in KBytes
octet 18 to
octet 21 - code flash size in KBytes
octet 22 to
octet 27 - serial number.
octet 28 - chassis backplane type.
chassis4000 = 0x00
chassis8000 = 0x04
Turbo8 = 0x07 (stack2)
FastIron2 = 0x06 (stack1) | ||||
| CsnAgentBrdMainPortTotal | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.4 | INTEGER (1..32) | RO | mandatory |
column · INTEGER (1..32) · read-only · mandatory The total number of ports for the main board. | ||||
| CsnAgentBrdExpBrdDescription | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.5 | DisplayString (SIZE (0..128)) | RO | mandatory |
column · DisplayString (SIZE (0..128)) · read-only · mandatory The expansion board description string. Expansion board are those boards attaching on the main board. | ||||
| CsnAgentBrdExpBrdId | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.6 | OCTET STRING | RO | mandatory |
column · OCTET STRING · read-only · mandatory The expansion board identifier. Expansion board are those
boards attaching on the main board. It is an encoded octet
string with the following meaning:
octet 0 - octet string format version, which identifies
the format of this string.
If format version octet has the value 1, the octets after
the version octet have the following meaning:
octet 1 - expansion board type, HUNDRED_MEG_1PORT=1,
HUNDRED_MEG_2PORT=2, HUNDRED_MEG_1PORT_COPPER=3,
HUNDRED_MEG_2PORT_COPPER=4, HUNDRED_MEG_2PORT_LX=5,
GIGA_1PORT=8, GIGA_2PORT=9
octet 2 - fiber port type, NONFIBER=0, SX_FIBER=1,
LX_FIBER=2, LHX_FIBER=3, LX_SX_FIBER=4 | ||||
| CsnAgentBrdExpPortTotal | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.7 | INTEGER (1..24) | RO | mandatory |
column · INTEGER (1..24) · read-only · mandatory The total number of ports for the expansion board. | ||||
| CsnAgentBrdStatusLeds | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.8 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory A bit array that contains the value of the
front panel status LEDs. This is a bit-map;
each LED is encoded into 1 bit for each switch
port. The maximum number of ports in one chassis
is 32 that means 32 Ports Status LEDs. The expansion port
number always begins from the last main port number.
The following shows the meaning of each bit for each
switch port:
bit value meaning
-------- ---------
0 off (Link off)
1 on (Link on)
The bitmap of LEDs are as following:
(Port1) (Port4) (Port8)
Bit (Bit0) (Bit3) (Bit7)
Byte 1: LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8
Byte 2: LED9 LED10 LED11 LED12 LED13 LED14 LED15 LED16
Byte 3: LED17 LED18 LED19 LED20 LED21 LED22 LED23 LED24
-------- | ||||
| CsnAgentBrdTrafficLeds | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.9 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory A bit array that contains the value of the
front panel traffic LEDs. This is a packed bit string;
each LED is encoded into 1 bit for each switch
port. The maximum number of ports in one chassis
is 24 that means 24 Ports Traffic LEDs. The expansion port
number always begins from the last main port number.
The following shows the meaning of each bit for each
switch port:
bit value meaning
-------- ---------
0 off (no traffic)
1 on (traffic)
The bitmap of LEDs are as following:
(Port1) (Port4) (Port8)
Bit (Bit0) (Bit3) (Bit7)
Byte 1: LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8
Byte 2: LED9 LED10 LED11 LED12 LED13 LED14 LED15 LED16
Byte 3: LED17 LED18 LED19 LED20 LED21 LED22 LED23 LED24
-------- | ||||
| CsnAgentBrdMediaLeds | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.10 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory A bit array that contains the value of the
front panel media LEDs. This is a packed bit string;
each LED is encoded into 1 bit for each switch port.
The maximum number of ports in one chassis is 24
that means 24 Ports Media LEDs. The expansion port
number always begins from the last main port number.
The following shows the meaning of each bit for each
switch port:
bit value meaning
--------- -------
0 half duplex
1 full duplex
The bitmap of LEDs are as following:
(Port1) (Port4) (Port8)
Bit (Bit0) (Bit3) (Bit7)
Byte 1: LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8
Byte 2: LED9 LED10 LED11 LED12 LED13 LED14 LED15 LED16
Byte 3: LED17 LED18 LED19 LED20 LED21 LED22 LED23 LED24
--------- | ||||
| CsnAgentBrdSpeedLeds | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.11 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory A bit array that contains the value of the
front panel media LEDs. This is a packed bit string;
each LED is encoded into 1 bit for each switch port.
The maximum number of ports in one chassis is 24
that means 24 Ports Speed LEDs. The expansion port
number always begins from the last main port number.
The following shows the meaning of each bit for each
switch port:
bit value meaning
--------- -------
0 10 MBit
1 100 MBit
The bitmap of LEDs are as following:
(Port1) (Port4) (Port8)
Bit (Bit0) (Bit3) (Bit7)
Byte 1: LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8
Byte 2: LED9 LED10 LED11 LED12 LED13 LED14 LED15 LED16
Byte 3: LED17 LED18 LED19 LED20 LED21 LED22 LED23 LED24
--------- | ||||
| CsnAgentBrdModuleStatus | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.12 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory By default, this mode is set to notActivated(0). moduleEmpty(0) ......... The slot of the chassis is empty. moduleGoingDown(2) ..... The module is going down. moduleRejected(3) ...... The module is being rejected due to wrong configuration. moduleBad(4) ........... The module Hardware is bad. moduleComingUp(9) ...... The module is in power-up cycle. moduleRunning(10) ....... The module is running.
| ||||
| CsnAgentBrdRedundantStatus | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.13 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The redundant status of a module. Non-management module always returns other(1). Management module returns the rest of the states.
| ||||
| CsnAgentBrdAlarmLeds | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.14 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory A bit array that contains the value of the
front panel media LEDs (for POS Module Only). This is a packed bit string;
each LED is encoded into 1 bit for each switch port.
The maximum number of ports in one chassis is 24
that means 24 Ports Speed LEDs. The expansion port
number always begins from the last main port number.
The following shows the meaning of each bit for each
switch port:
bit value meaning
--------- -------
0 no alarm
1 alarm
The bitmap of LEDs are as following:
(Port1) (Port4) (Port8)
Bit (Bit0) (Bit3) (Bit7)
Byte 1: LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8
Byte 2: LED9 LED10 LED11 LED12 LED13 LED14 LED15 LED16
Byte 3: LED17 LED18 LED19 LED20 LED21 LED22 LED23 LED24
--------- | ||||
| CsnAgentBrdTxTrafficLeds | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.15 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory A bit array that contains the value of the
front panel transmit traffic LEDs (for POS Module Only). This is a packed bit string;
each LED is encoded into 1 bit for each switch
port. The maximum number of ports in one chassis
is 24 that means 24 Ports Transmit Traffic LEDs. The expansion port
number always begins from the last main port number.
The following shows the meaning of each bit for each
switch port:
bit value meaning
-------- ---------
0 off (no transmit traffic)
1 on (transmit traffic)
The bitmap of LEDs are as following:
(Port1) (Port4) (Port8)
Bit (Bit0) (Bit3) (Bit7)
Byte 1: LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8
Byte 2: LED9 LED10 LED11 LED12 LED13 LED14 LED15 LED16
Byte 3: LED17 LED18 LED19 LED20 LED21 LED22 LED23 LED24
-------- | ||||
| CsnAgentBrdRxTrafficLeds | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.16 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory A bit array that contains the value of the
front panel receive traffic LEDs (for POS Module Only). This is a packed bit string;
each LED is encoded into 1 bit for each switch
port. The maximum number of ports in one chassis
is 24 that means 24 Ports Receive Traffic LEDs. The expansion port
number always begins from the last main port number.
The following shows the meaning of each bit for each
switch port:
bit value meaning
-------- ---------
0 off (no receive traffic)
1 on (receive traffic)
The bitmap of LEDs are as following:
(Port1) (Port4) (Port8)
Bit (Bit0) (Bit3) (Bit7)
Byte 1: LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8
Byte 2: LED9 LED10 LED11 LED12 LED13 LED14 LED15 LED16
Byte 3: LED17 LED18 LED19 LED20 LED21 LED22 LED23 LED24
-------- | ||||
| NsnAgentTrp | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.3 | |||
| TsnAgTrpRcvrTable | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.3.1 | NA | mandatory | |
table · not-accessible · mandatory A table of managers which to send traps. | ||||
| RsnAgTrpRcvrEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.3.1.1 | NA | mandatory | |
row · not-accessible · mandatory A row in the trap receiver table. The column snAgTrpRcvrStatus is used to create and delete rows in the table. Creation requires a SET PDU with objects snAgTrpRcvrIndex, snAgTrpRcvrIpAddr, snAgTrpRcvrComm and snAgTrpRcvrStatus.
| ||||
| CsnAgTrpRcvrIndex | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.3.1.1.1 | INTEGER (1..10) | RO | mandatory |
column · INTEGER (1..10) · read-only · mandatory The index to the Trap Receiver Table. | ||||
| CsnAgTrpRcvrIpAddr | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.3.1.1.2 | IpAddress | RW | mandatory |
column · IpAddress · read-write · mandatory The ip address for SNMP manager that is to receive the trap. | ||||
| CsnAgTrpRcvrComm | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.3.1.1.3 | OCTET STRING (SIZE (0..32)) | RW | mandatory |
column · OCTET STRING (SIZE (0..32)) · read-write · mandatory Community string to use. | ||||
| CsnAgTrpRcvrStatus | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.3.1.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory This object is used to create and
delete rows in the table and control
if they are used. The values
that can be written are:
ignore(5)...don't use this entry to
send traps to at this time
delete(3)...deletes the row
create(4)...creates a new row
If the row exists, then a SET with
value of create(5) returns error
'badValue'. Deleted rows go away
immediately. The following values
can be returned on reads:
other(1)....some other case
valid(2)....the row exists and is valid
ignore(5)...don't use this entry to
send traps to at this time
| ||||
| NsnAgentBoot | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.4 | |||
| TsnAgBootSeqTable | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.4.1 | NA | mandatory | |
table · not-accessible · mandatory A table of image load sequnce instructions to the boot code. Boot code will start from instruction of the first valid entry to load the image. If failed, it will use the second valid entry and so on, until a succesful load has completed. Each entry must have an unique instruction, duplicate instructions will be rejected. | ||||
| RsnAgBootSeqEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.4.1.1 | NA | mandatory | |
| CsnAgBootSeqIndex | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.4.1.1.1 | INTEGER (1..4) | RO | mandatory |
column · INTEGER (1..4) · read-only · mandatory The index to the boot sequence table. | ||||
| CsnAgBootSeqInstruction | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.4.1.1.2 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory The instruction for the boot code.
| ||||
| CsnAgBootSeqIpAddr | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.4.1.1.3 | IpAddress | RW | mandatory |
column · IpAddress · read-write · mandatory The ip address of the TFTP server if snAgBootSeqInstruction was set to 'fromTftpServer'; otherwise, this object is not used in any other boot instruction. | ||||
| CsnAgBootSeqFilename | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.4.1.1.4 | DisplayString (SIZE (0..32)) | RW | mandatory |
column · DisplayString (SIZE (0..32)) · read-write · mandatory The image filename on the TFTP server if snAgBootSeqInstruction was set to 'fromTftpServer'; otherwise, this object is not used in any other boot instruction. | ||||
| CsnAgBootSeqRowStatus | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.4.1.1.5 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory To create or delete a boot sequence table entry.
| ||||
| NsnAgCfgEos | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.5 | |||
| TsnAgCfgEosTable | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.5.1 | NA | mandatory | |
table · not-accessible · mandatory This table represents the fragmented Configuration File data packet with checksum include in each rows of this table. A SNMP-SET represents configuration file download, and a SNMP-GET represents configuration file upload. This action is only if the SNMP-SET of snAgCfgLoad command is sent along with this table consecutively. The applicable snAgCfgLoad command value is as followings: uploadFromFlashToNMS(23), downloadToFlashFromNMS(24), uploadFromDramToNMS(25), downloadToDramFromNMS(26). | ||||
| RsnAgCfgEosEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.5.1.1 | NA | mandatory | |
row · not-accessible · mandatory An EOS row in the table of encoded octet strings for table snAgCfgEosTable.
| ||||
| CsnAgCfgEosIndex | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.5.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory Each VLAN EOS Buffer Identifier have a multiple VLAN table entries. | ||||
| CsnAgCfgEosPacket | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.5.1.1.2 | OCTET STRING (SIZE (0..1000)) | RW | mandatory |
column · OCTET STRING (SIZE (0..1000)) · read-write · mandatory An encoded octet string. On reads it contains an integral number of configuration file data packets. The size of each encoded octet string is less than or equal to 1400 bytes. | ||||
| CsnAgCfgEosChkSum | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.5.1.1.3 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory A checksum of each configuration file data packet. | ||||
| NsnAgentLog | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.6 | |||
| NsnAgSysLogGbl | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.1 | |||
| SsnAgSysLogGblEnable | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.1.1 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Enable/disable system logging.
| ||||
| SsnAgSysLogGblBufferSize | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.1.2 | INTEGER (1..100) | RW | mandatory |
scalar · INTEGER (1..100) · read-write · mandatory The number of dynamic system logging entries. | ||||
| SsnAgSysLogGblClear | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.1.3 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Clear dynamic and/or static system logging buffers.
| ||||
| SsnAgSysLogGblCriticalLevel | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.1.4 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Filter events going to the logging buffer. This is a packed
bit string object of which each bit has the following meaning:
(bit 0 is the least significant bit).
bit position meaning
------------ -------
8-31 reserved
7 Warning (warning conditions)
6 Notification (normal but significant conditions)
5 Informational (informational messages)
4 Error (error conditions)
3 Emergency (system is unusable)
2 Debugging (debugging messages)
1 Critical (critical conditions)
0 Alert (immediate action needed)
Setting a critical level bit to 1 makes the logging buffer
accept the corresponding event. Resetting a critical level
bit to 0 makes the logging buffer reject the corresponding
event. | ||||
| SsnAgSysLogGblLoggedCount | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.1.5 | Counter | RO | mandatory |
scalar · Counter · read-only · mandatory The number events logged in the system logging buffer. | ||||
| SsnAgSysLogGblDroppedCount | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.1.6 | Counter | RO | mandatory |
scalar · Counter · read-only · mandatory The number of events dropped. | ||||
| SsnAgSysLogGblFlushedCount | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.1.7 | Counter | RO | mandatory |
scalar · Counter · read-only · mandatory The number of times that the system logging buffer was cleared. | ||||
| SsnAgSysLogGblOverrunCount | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.1.8 | Counter | RO | mandatory |
scalar · Counter · read-only · mandatory The number of times that the system logging buffer was wrapped around. | ||||
| SsnAgSysLogGblServer | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.1.9 | IpAddress | RW | mandatory |
scalar · IpAddress · read-write · mandatory IP address of syslog server. | ||||
| SsnAgSysLogGblFacility | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.1.10 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Facility code.
| ||||
| TsnAgSysLogBufferTable | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.2 | NA | mandatory | |
table · not-accessible · mandatory Dynamic system logging buffer table. | ||||
| RsnAgSysLogBufferEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.2.1 | NA | mandatory | |
row · not-accessible · mandatory A row in the dynamic system logging buffer table. | ||||
| CsnAgSysLogBufferIndex | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.2.1.1 | INTEGER (1..100) | RO | mandatory |
column · INTEGER (1..100) · read-only · mandatory The index to the dynamic system logging buffer table. | ||||
| CsnAgSysLogBufferTimeStamp | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.2.1.2 | TimeTicks | RO | mandatory |
column · TimeTicks · read-only · mandatory A time stamp when the event is logged. | ||||
| CsnAgSysLogBufferCriticalLevel | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.2.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The critical level of this event.
| ||||
| CsnAgSysLogBufferMessage | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.2.1.4 | DisplayString | RO | mandatory |
column · DisplayString · read-only · mandatory The system logging message. | ||||
| CsnAgSysLogBufferCalTimeStamp | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.2.1.5 | DisplayString | RO | mandatory |
column · DisplayString · read-only · mandatory A time stamp when the event is logged. This object returns a NULL terminated time stamp string if the system calendar time was set. It returns a zero length string if the system calendar time was not set. | ||||
| TsnAgStaticSysLogBufferTable | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.3 | NA | mandatory | |
table · not-accessible · mandatory Static system logging buffer table. | ||||
| RsnAgStaticSysLogBufferEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.3.1 | NA | mandatory | |
row · not-accessible · mandatory A row in the static system logging buffer table. | ||||
| CsnAgStaticSysLogBufferIndex | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.3.1.1 | INTEGER (1..100) | RO | mandatory |
column · INTEGER (1..100) · read-only · mandatory The index to the static system logging buffer table. | ||||
| CsnAgStaticSysLogBufferTimeStamp | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.3.1.2 | TimeTicks | RO | mandatory |
column · TimeTicks · read-only · mandatory A time stamp when the event is logged. | ||||
| CsnAgStaticSysLogBufferCriticalLevel | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.3.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The critical level of this event.
| ||||
| CsnAgStaticSysLogBufferMessage | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.3.1.4 | DisplayString | RO | mandatory |
column · DisplayString · read-only · mandatory The system logging message. | ||||
| CsnAgStaticSysLogBufferCalTimeStamp | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.3.1.5 | DisplayString | RO | mandatory |
column · DisplayString · read-only · mandatory A time stamp when the event is logged. This object returns a NULL terminated time stamp string if the system calendar time was set. It returns a zero length string if the system calendar time was not set. | ||||
| NsnAgentSysParaConfig | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.7 | |||
| TsnAgentSysParaConfigTable | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.7.1 | NA | mandatory | |
table · not-accessible · mandatory A table of Agent of each board. | ||||
| RsnAgentSysParaConfigEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.7.1.1 | NA | mandatory | |
row · not-accessible · mandatory A row in the Agent System Parameters Configuation table. | ||||
| CsnAgentSysParaConfigIndex | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.7.1.1.1 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The index to the Agent System Parameters Configuation Table. | ||||
| CsnAgentSysParaConfigDescription | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.7.1.1.2 | DisplayString (SIZE (0..32)) | RO | mandatory |
column · DisplayString (SIZE (0..32)) · read-only · mandatory The main board description string. | ||||
| CsnAgentSysParaConfigMin | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.7.1.1.3 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The minimum value of this Agent System Parameter. | ||||
| CsnAgentSysParaConfigMax | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.7.1.1.4 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The maximum value of this Agent System Parameter. | ||||
| CsnAgentSysParaConfigDefault | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.7.1.1.5 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The default value of this Agent System Parameter. | ||||
| CsnAgentSysParaConfigCurrent | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.7.1.1.6 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory The current configurated value of this Agent System Parameter. | ||||
| NsnAgentConfigModule | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.8 | |||
| TsnAgentConfigModuleTable | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.8.1 | NA | mandatory | |
table · not-accessible · mandatory A table of each configured module information. | ||||
| RsnAgentConfigModuleEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.8.1.1 | NA | mandatory | |
row · not-accessible · mandatory A row in the Agent Configured Module table. | ||||
| CsnAgentConfigModuleIndex | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.8.1.1.1 | INTEGER (1..8) | RO | mandatory |
column · INTEGER (1..8) · read-only · mandatory The index to the Agent Configured Module Table. | ||||
| CsnAgentConfigModuleType | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.8.1.1.2 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory The Configured Module Type.
| ||||
| CsnAgentConfigModuleRowStatus | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.8.1.1.3 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory To create or delete a configured module table entry.
| ||||
| NsnAgentUser | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.9 | |||
| NsnAgentUserGbl | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.9.1 | |||
| SsnAgentUserMaxAccnt | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.9.1.1 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory Maximum number of user account entries can be configured. | ||||
| TsnAgentUserAccntTable | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.9.2 | NA | mandatory | |
table · not-accessible · mandatory A table of user account information. | ||||
| RsnAgentUserAccntEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.9.2.1 | NA | mandatory | |
| CsnAgentUserAccntName | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.9.2.1.1 | DisplayString (SIZE (1..48)) | RO | mandatory |
column · DisplayString (SIZE (1..48)) · read-only · mandatory The user name. | ||||
| CsnAgentUserAccntPassword | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.9.2.1.2 | DisplayString (SIZE (0..48)) | RW | mandatory |
column · DisplayString (SIZE (0..48)) · read-write · mandatory The user password. | ||||
| CsnAgentUserAccntEncryptCode | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.9.2.1.3 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory The password encryption method code. | ||||
| CsnAgentUserAccntPrivilege | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.9.2.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory The user privilege. | ||||
| CsnAgentUserAccntRowStatus | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.9.2.1.5 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory To create or delete a user account table entry.
| ||||
| NsnAgentRedundant | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.10 | |||
| NsnAgentRedunGbl | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.10.1 | |||
| SsnAgentRedunActiveMgmtMod | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.10.1.1 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Slot number of the active management module. Setting this object does not take effect immediately. Saving configuration data to flash storage and reboot the system are required to take effect. Setting a value of 0 requests the system to auto-select an active management module after power up. | ||||
| SsnAgentRedunSyncConfig | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.10.1.2 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Frequency of the backup management module copying the configuration data from the active management module. Each unit is 1 second. Setting a value 0 will disable the synchronization copy. Setting a negative value will initiate the synchronization copy once immediately. | ||||
| SsnAgentRedunBkupCopyBootCode | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.10.1.3 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory If enabled(1), the backup management module copies the boot code from the active management module to its boot code flash storage after power up, and whenever the active management module's boot code is updated. The backup management module does not copy if both boot codes were identical.
| ||||
| SsnAgentEnableMgmtModRedunStateChangeTrap | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.10.1.4 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Indicates whether the SNMP agent process is permitted to generate management module redundancy state change traps.
| ||||
| SsnAgentRedunBkupBootLoad | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.10.1.5 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Action object to down load a new boot code from boot flash storage
of the active management module to the backup management module.
The following are returned values from get operation:
normal(1)............no operation
operationError(17)...error codes
The following are input values from set operation:
downloadBackup(20)...download the boot code from the active
management module to the backup management
module
Any set operation is rejected during loading until error
or normal state is reached.
| ||||
| SsnAgentRedunSwitchOver | 1.3.6.1.4.1.11.2.3.7.11.12.1.2.10.1.6 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory To force a switch-over from standby to active state if the backup management module exists in a chassis.
| ||||
| NsnStackGen | 1.3.6.1.4.1.11.2.3.7.11.12.1.5.1 | |||
| SsnStackPriSwitchMode | 1.3.6.1.4.1.11.2.3.7.11.12.1.5.1.1 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory The Stackable Management Primary Switch mode either enabled or disabled and the default is disabled mode. enabled(1)...........primary switch enabled disabled(0)..........primary switch disabled
| ||||
| SsnStackMaxSecSwitch | 1.3.6.1.4.1.11.2.3.7.11.12.1.5.1.2 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory The Maximum Secondary Switches are allowed in the Stackable Management Group. | ||||
| SsnStackTotalSecSwitch | 1.3.6.1.4.1.11.2.3.7.11.12.1.5.1.3 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory The Total Secondary Switches currently connected to the Stackable Management Group. | ||||
| SsnStackSyncAllSecSwitch | 1.3.6.1.4.1.11.2.3.7.11.12.1.5.1.4 | INTEGER | RW | mandatory |
scalar · INTEGER · read-write · mandatory Synchronize all the secondary switches in the Stackable Management Group with the following commands. device(2)...........device related parameters. global(3)...........global parameters. local(4)............local parameters. The return result of the above commands are either normal(0)...........normal condition. invalid(1)...........invalid result.
| ||||
| SsnStackSmSlotIndex | 1.3.6.1.4.1.11.2.3.7.11.12.1.5.1.5 | INTEGER (0..8) | RW | mandatory |
scalar · INTEGER (0..8) · read-write · mandatory The Slot 0 is the Master slot and Slot 1-8 are slaves. All the slot-based MIB data can be retrieved with respect to this slot index such as snChassis global MIB. | ||||
| SsnStackFmpSetProcess | 1.3.6.1.4.1.11.2.3.7.11.12.1.5.1.6 | INTEGER | RO | mandatory |
scalar · INTEGER · read-only · mandatory normal(0) - The set process is either in an idle state or FMP-SET-SUCCESS state. pending(1) - The pending process is waiting for the result of an FMP-SET. failure(2) - The failure result of an FMP-SET.
| ||||
| NsnStackSecSwitchInfo | 1.3.6.1.4.1.11.2.3.7.11.12.1.5.2 | |||
| TsnStackSecSwitchTable | 1.3.6.1.4.1.11.2.3.7.11.12.1.5.2.1 | NA | mandatory | |
table · not-accessible · mandatory If snSwGroupOperMode is configured as basic mode which is VLAN by Port, Layer2 switching, then this table is valid. Each VLAN switch port could have a number of VLAN IDs. | ||||
| RsnStackSecSwitchEntry | 1.3.6.1.4.1.11.2.3.7.11.12.1.5.2.1.1 | NA | mandatory | |
row · not-accessible · mandatory An entry in the Stackable Management Secondary Switch Information table. | ||||
| CsnStackSecSwitchIndex | 1.3.6.1.4.1.11.2.3.7.11.12.1.5.2.1.1.1 | INTEGER (1..26) | RO | mandatory |
column · INTEGER (1..26) · read-only · mandatory The secondary switch index must not be greater than the snStackMaxSecSwitch. | ||||
| CsnStackSecSwitchSlotId | 1.3.6.1.4.1.11.2.3.7.11.12.1.5.2.1.1.2 | INTEGER (1..26) | RW | mandatory |
column · INTEGER (1..26) · read-write · mandatory The secondary switch slot ID must be set before the Configuration command sent from the primary switch to the secondary switch either manually or automatically - snStackSecSwitchCfgCmd. | ||||
| CsnStackSecSwitchPortCnts | 1.3.6.1.4.1.11.2.3.7.11.12.1.5.2.1.1.3 | INTEGER (1..26) | RO | mandatory |
column · INTEGER (1..26) · read-only · mandatory The number of ports in this secondary switch. | ||||
| CsnStackSecSwitchEnabled | 1.3.6.1.4.1.11.2.3.7.11.12.1.5.2.1.1.4 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory The secondary switch has been selected to Stackable Management Group.
| ||||
| CsnStackSecSwitchAck | 1.3.6.1.4.1.11.2.3.7.11.12.1.5.2.1.1.5 | INTEGER | RO | mandatory |
column · INTEGER · read-only · mandatory The secondary switch has sent reponse to the primary switch.
| ||||
| CsnStackSecSwitchMacAddr | 1.3.6.1.4.1.11.2.3.7.11.12.1.5.2.1.1.6 | MacAddress | RO | mandatory |
column · MacAddress · read-only · mandatory The secondary switch physical address. The physical address represents a MAC Station. | ||||
| CsnStackSecSwitchSyncCmd | 1.3.6.1.4.1.11.2.3.7.11.12.1.5.2.1.1.7 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory Synchronize the secondary switches in the Stackable Management Group with the following commands. device(2)...........device related parameters. global(3)...........global parameters. local(4)............local parameters. The return result of the above commands are either normal(0)...........normal condition. invalid(1)...........invalid result.
| ||||
| CsnStackSecSwitchIpAddr | 1.3.6.1.4.1.11.2.3.7.11.12.1.5.2.1.1.8 | IpAddress | RW | mandatory |
column · IpAddress · read-write · mandatory The secondary switch IP Address and is used for manual-command of snStackSecSwitchCfgCmd. | ||||
| CsnStackSecSwitchSubnetMask | 1.3.6.1.4.1.11.2.3.7.11.12.1.5.2.1.1.9 | IpAddress | RW | mandatory |
column · IpAddress · read-write · mandatory The secondary switch IP Subnet Mask and is used for manual-command of snStackSecSwitchCfgCmd. | ||||
| CsnStackSecSwitchCfgCmd | 1.3.6.1.4.1.11.2.3.7.11.12.1.5.2.1.1.10 | INTEGER | RW | mandatory |
column · INTEGER · read-write · mandatory snStackSecSwitchSlotId must be set before the Configuration
command sent from the primary switch to the secondary switch
either manually or automatically.
auto(2)...........auto-configuration command sent.
manual(3).........manual-configuration command sent.
if manual-mode is used, snStackSecSwitchIpAddr
and snStackSecSwitchSubnetMask must be
first set before this command is sent.
The return result of the above commands are either
normal(0)...........normal condition.
invalid(1)..........invalid result.
| ||||