XF-RADIOLINK-PTP-RADIO-MIB
Ericsson ABThis MIB defines objects for point-to-point Radio Link RAUs.
snmptranslate -m XF-RADIOLINK-PTP-RADIO-MIB -Tpsnmpwalk -v2c -c <community> -m XF-RADIOLINK-PTP-RADIO-MIB <host> 1.3.6.1.4.1.193.81.3.4.3Imports
| ENTITY-MIB | entPhysicalIndex |
|---|---|
| IF-MIB | ifIndex |
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP |
| SNMPv2-SMI | Bits, Integer32, IpAddress, MODULE-IDENTITY, MibIdentifier, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, iso |
| SNMPv2-TC | DisplayString, PhysAddress, TEXTUAL-CONVENTION |
| XF-RADIOLINK-PTP-TERMINAL-MIB | xfTermRowIndex |
| XF-TOP-MIB | xfRadioLink |
OID tree
| Name | OID | Type | Access | Status | Example | ||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| IxfRadioLinkPtpRadioMIB | 1.3.6.1.4.1.193.81.3.4.3 | ||||||||||||||||||||
identity This MIB defines objects for point-to-point Radio Link RAUs. | |||||||||||||||||||||
| NxfRadioLinkPtpRadioObjects | 1.3.6.1.4.1.193.81.3.4.3.1 | ||||||||||||||||||||
| TxfRAUTable | 1.3.6.1.4.1.193.81.3.4.3.1.1 | NA | |||||||||||||||||||
table · not-accessible · current Table for Radiolink point-to-point radios managed objects. Table indexed with entPhysicalIndex. | |||||||||||||||||||||
| RxfRAUEntry | 1.3.6.1.4.1.193.81.3.4.3.1.1.1 | NA | |||||||||||||||||||
| CxfRAUAlarmStatus | 1.3.6.1.4.1.193.81.3.4.3.1.1.1.1 | Bits | RO | 00 00 00 | |||||||||||||||||
column · Bits · read-only · current This object shows the alarm status of the radio unit.
atpcCability - The terminal is configured for ATPC, but the radio does not support ATPC.
This alarm is activated only if ATPC is turned on (any direction).
sdcHwErrorMain - Received RF input signal level for Main path (of SDC TRX) has dropped below the threshold for the receiver.
sdcHwErrorDiv - Received RF input signal level for Diversity path (of SDC TRX) has dropped below the threshold for the receiver.
sdcDadeCalMismatch - A TRX is connected and its Serial Number doesn't match with the serial number stored into MO xfTRXSdcSerialNumber.
insufficientResourceRauXpic - Connected RAU is missing capabilities for XPIC.
companionRauMismatch - Connected RAU does not match with the companion one, either in 1+1 RLP or XPIC.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CxfRAURfLoopAvailable | 1.3.6.1.4.1.193.81.3.4.3.1.1.1.2 | RAURfLoopAvailable | RO | 0 | |||||||||||||||||
column · RAURfLoopAvailable · read-only · current This object inidicates if RF loop is available in radio unit. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CxfRAUAtpcCapability | 1.3.6.1.4.1.193.81.3.4.3.1.1.1.3 | RAUAtpcCapability | RO | 0 | |||||||||||||||||
column · RAUAtpcCapability · read-only · current This object indicates if the radio unit supports ATPC or not. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CxfRAULocalCtrlCapability | 1.3.6.1.4.1.193.81.3.4.3.1.1.1.4 | INTEGER | RO | 0 | |||||||||||||||||
column · INTEGER · read-only · current This object indicates if the radio unit supports local transmit power control or not.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CxfRAUModCapability | 1.3.6.1.4.1.193.81.3.4.3.1.1.1.5 | RAUModCapability | RO | 00 00 00 00 | |||||||||||||||||
column · RAUModCapability · read-only · current This object shows the modulation methods supported by the radio unit. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CxfRAUFrequencyband | 1.3.6.1.4.1.193.81.3.4.3.1.1.1.6 | Unsigned32 (0..255) | RO | 0 | |||||||||||||||||
column · Unsigned32 (0..255) · read-only · current This object shows the frequency band for the radio unit. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CxfRAUSubBand | 1.3.6.1.4.1.193.81.3.4.3.1.1.1.7 | Unsigned32 (0..255) | RW | 0 | |||||||||||||||||
column · Unsigned32 (0..255) · read-write · current This object shows the sub band (Index) for the radio unit. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CxfRAUTemperature | 1.3.6.1.4.1.193.81.3.4.3.1.1.1.8 | Integer32 (-127..127) | RO | 0 | |||||||||||||||||
column · Integer32 (-127..127) · read-only · current This object shows the temperature, in degree Celsius, inside the radio unit. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CxfRAUProtectionPath | 1.3.6.1.4.1.193.81.3.4.3.1.1.1.9 | INTEGER | RO | 0 | |||||||||||||||||
column · INTEGER · read-only · current This object indicates what radio path the radio belongs to.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CxfRAURxCapability | 1.3.6.1.4.1.193.81.3.4.3.1.1.1.10 | INTEGER | RO | 0 | |||||||||||||||||
column · INTEGER · read-only · current This object indicates if the radio unit support RX configuration.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CxfRAUNotes | 1.3.6.1.4.1.193.81.3.4.3.1.1.1.11 | OCTET STRING (SIZE (0..800)) | RW | | |||||||||||||||||
column · OCTET STRING (SIZE (0..800)) · read-write · current You can add information in this description field, for example polarization, antenna type or logging a site visit. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CxfRauAtpcVersion | 1.3.6.1.4.1.193.81.3.4.3.1.1.1.12 | INTEGER | RO | 0 | |||||||||||||||||
column · INTEGER · read-only · current This object represents the RAU ATPC version.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CxfRauBoosterCapability | 1.3.6.1.4.1.193.81.3.4.3.1.1.1.13 | BoosterCapability | RO | ||||||||||||||||||
column · BoosterCapability · read-only · current This object represents the Booster capability for a link. | |||||||||||||||||||||
| CxfRauBoosterSelectedIndex | 1.3.6.1.4.1.193.81.3.4.3.1.1.1.14 | Integer32 (0..2147483647) | RW | ||||||||||||||||||
column · Integer32 (0..2147483647) · read-write · current This object represents the Booster selected index for a link. | |||||||||||||||||||||
| TxfRFIFTable | 1.3.6.1.4.1.193.81.3.4.3.1.2 | NA | |||||||||||||||||||
table · not-accessible · current Table for Radiolink point-to-point radios RF IF managed objects. Table indexed with ifIndex. | |||||||||||||||||||||
| RxfRFIFEntry | 1.3.6.1.4.1.193.81.3.4.3.1.2.1 | NA | |||||||||||||||||||
| CxfRFBaseTxFrequency | 1.3.6.1.4.1.193.81.3.4.3.1.2.1.1 | Unsigned32 (0..4294967295) | RO | 6330540 | |||||||||||||||||
column · Unsigned32 (0..4294967295) · read-only · current This object shows the Tx frequency in KHz when frequency step number is 0. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CxfRFBaseRxFrequency | 1.3.6.1.4.1.193.81.3.4.3.1.2.1.2 | Unsigned32 (0..4294967295) | RO | 6078490 | |||||||||||||||||
column · Unsigned32 (0..4294967295) · read-only · current This object shows the Rx frequency in KHz when frequency. step number is 0 Example values from LibreNMS test devices
| |||||||||||||||||||||
| CxfRFStepSize | 1.3.6.1.4.1.193.81.3.4.3.1.2.1.3 | Unsigned32 (0..65535) | RO | ||||||||||||||||||
column · Unsigned32 (0..65535) · read-only · current This object shows the frequency step size in KHz. | |||||||||||||||||||||
| CxfRFStepLimitLow | 1.3.6.1.4.1.193.81.3.4.3.1.2.1.4 | Unsigned32 (0..65535) | RO | ||||||||||||||||||
column · Unsigned32 (0..65535) · read-only · current This object shows the lowest allowed frequency step number. | |||||||||||||||||||||
| CxfRFStepLimitHigh | 1.3.6.1.4.1.193.81.3.4.3.1.2.1.5 | Unsigned32 (0..65535) | RO | ||||||||||||||||||
column · Unsigned32 (0..65535) · read-only · current This object shows the highest allowed frequency step number. | |||||||||||||||||||||
| CxfRFCurrentStepNumber | 1.3.6.1.4.1.193.81.3.4.3.1.2.1.6 | Unsigned32 (0..65535) | RW | ||||||||||||||||||
column · Unsigned32 (0..65535) · read-write · current This object sets/shows the frequency step number. 0 = frequency not yet defined. For Classic RAUs, TX and RX frequencies can not be set individually. The span between them is always fixed and depends on different frequency and sub band. - To calculate step number for TX and RX, use the following formulas: New step number = (TX frequency - XfRAUBaseTxFrequency) / XfRAUStepSize New step number = (RX frequency - xfRAUBaseRxFrequency) / XfRAUStepSize - To calculate TX and RX frequencies, use the following formulas: TX frequency = XfRAUBaseTxFrequency + XfRAUCurrentStepNumber * XfRAUStepSize RX frequency = XfRAUBaseRxFrequency + XfRAUCurrentStepNumber * XfRAUStepSize For Agile RAUs, the TX and RX frequencies can be set individually. Above formulas are only valid for TX frequency. For RX frequency, xfRFCurrentStepNumberRx must be used. Default value: 0 | |||||||||||||||||||||
| CxfRFTxOperStatus | 1.3.6.1.4.1.193.81.3.4.3.1.2.1.7 | RFTxOperStatus | RO | 4 | |||||||||||||||||
column · RFTxOperStatus · read-only · current This object shows the operational status of the transmitter. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CxfRFTxAdminStatus | 1.3.6.1.4.1.193.81.3.4.3.1.2.1.8 | INTEGER | RW | txOn(3) | |||||||||||||||||
column · INTEGER · read-write · current This object sets the desired status of the transmitter.
Value other(1) not settable.
Especially for far end:
txOff(2), requests far end transmitter to be turned off.
txOn(3), requests far end transmitter to be turned on.
Default value: txOff(2) - near end.
other(1) - far end.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CxfRFLoopEnable | 1.3.6.1.4.1.193.81.3.4.3.1.2.1.9 | INTEGER | RW | ||||||||||||||||||
column · INTEGER · read-write · current This object manage RF loop. Default value: disable(3). Near end access: read-write. Far end access: no access.
| |||||||||||||||||||||
| CxfRFAlarms | 1.3.6.1.4.1.193.81.3.4.3.1.2.1.10 | Bits | RO | ||||||||||||||||||
column · Bits · read-only · current This TC enumerates the alarms for RF interface.
txFrequency - Transmitter frequency synthesizer loop is unlocked.
rxFrequency - Receiver frequency synthesizer loop is unlocked.
rfOutputLevel - Major degradation of transmitter output power is detected.
rxAfc - The frequency of the received signal is outside the range of the Automatic Frequency Control in the RAU receiver.
rfInputLevel - Receiver RF input signal level has dropped below the threshold for the receiver.
rfInputThreshold - The RF input level has dropped below the xfRFInputAlarmThreshold.
rfOutputLevelATPC - The transmitter output power has been continuously at 'Patpc,max' for too long.
This can occur due to several reasons:
* The operator has set 'Patpc,max' too low.
* The hop attenuation has increased (steady-state).
* The transmitter PA is v.
* The LNA in Rx is deteriorating.
| |||||||||||||||||||||
| CxfRFStatus | 1.3.6.1.4.1.193.81.3.4.3.1.2.1.11 | Bits | RO | ||||||||||||||||||
column · Bits · read-only · current This object shows the RAU status. rfLoop - Warns if RF-loop is enabled on RAU txOff - Warns if TX is manually set to off
| |||||||||||||||||||||
| CxfRFStepSizeRx | 1.3.6.1.4.1.193.81.3.4.3.1.2.1.12 | Unsigned32 (0..65535) | RO | ||||||||||||||||||
column · Unsigned32 (0..65535) · read-only · current This object shows the Rx frequency step size in KHz. | |||||||||||||||||||||
| CxfRFStepLimitLowRx | 1.3.6.1.4.1.193.81.3.4.3.1.2.1.13 | Unsigned32 (0..65535) | RO | ||||||||||||||||||
column · Unsigned32 (0..65535) · read-only · current This object shows the Rx lowest allowed frequency step number. | |||||||||||||||||||||
| CxfRFStepLimitHighRx | 1.3.6.1.4.1.193.81.3.4.3.1.2.1.14 | Unsigned32 (0..65535) | RO | ||||||||||||||||||
column · Unsigned32 (0..65535) · read-only · current This object shows the Rx highest allowed frequency step number. | |||||||||||||||||||||
| CxfRFCurrentStepNumberRx | 1.3.6.1.4.1.193.81.3.4.3.1.2.1.15 | Unsigned32 (0..65535) | RW | ||||||||||||||||||
column · Unsigned32 (0..65535) · read-write · current This object sets/shows the RX frequency step number for Agile RAUs. 0 = frequency not yet defined. - To calculate step number for RX, use the following formula: New step number Rx = (RX frequency - xfRAUBaseRxFrequency) / XfRAUStepSizeRx - To calculate RX frequency, use the following formula: RX frequency = XfRAUBaseRxFrequency + XfRAUCurrentStepNumberRx * XfRAUStepSizeRx Default value: 0 | |||||||||||||||||||||
| CxfRFDuplexType | 1.3.6.1.4.1.193.81.3.4.3.1.2.1.16 | INTEGER | RO | ||||||||||||||||||
column · INTEGER · read-only · current This object tells the duplex frequency mode for the RAU: - fixed: Tx frequency only can be set by operator, Rx frequency is automatically set on the basis of (fixed) RAU duplex frequency - variable: duplex frequency can be configured by operator
| |||||||||||||||||||||
| CxfRFDuplexConfig | 1.3.6.1.4.1.193.81.3.4.3.1.2.1.17 | INTEGER | RW | ||||||||||||||||||
column · INTEGER · read-write · current This object enables setting of duplex frequency for the RAU. It is always disabled(3) and can not be overwritten if xfRFDuplexType = fixed(2).
| |||||||||||||||||||||
| CxfRFDuplexDistance | 1.3.6.1.4.1.193.81.3.4.3.1.2.1.18 | Integer32 (-2147483647..2147483647) | RW | ||||||||||||||||||
column · Integer32 (-2147483647..2147483647) · read-write · current This object is aimed to select the duplex distance for the RAU.
It can only be set if xfRFDuplexConfig = enabled(2), so that:
xfRFDuplexDistance = Tx Frequency - Rx Frequency
Otherwise, it is automatically filled on the basis of Tx and Rx
frequency settings, and can not be overwritten. | |||||||||||||||||||||
| TxfRFPowerTable | 1.3.6.1.4.1.193.81.3.4.3.1.3 | NA | |||||||||||||||||||
table · not-accessible · current Table for Radiolink point-to-point radios managed objects. Table indexed with ifIndex. | |||||||||||||||||||||
| RxfRFPowerEntry | 1.3.6.1.4.1.193.81.3.4.3.1.3.1 | NA | |||||||||||||||||||
| CxfRFCurrentOutputPower | 1.3.6.1.4.1.193.81.3.4.3.1.3.1.1 | Integer32 (-100..45 | 255) | RO | -99 | |||||||||||||||||
column · Integer32 (-100..45 | 255) · read-only · current This object shows the output power in dBm including attenuator. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CxfRFRtpcMinOutputPower | 1.3.6.1.4.1.193.81.3.4.3.1.3.1.2 | Integer32 (-100..45 | 255) | RO | ||||||||||||||||||
column · Integer32 (-100..45 | 255) · read-only · current This object shows the minimum output power in dBm including attenuator. Value -100 indicate that RAU Tx on is not possible due to power supply limitations. | |||||||||||||||||||||
| CxfRFRtpcMaxOutputPower | 1.3.6.1.4.1.193.81.3.4.3.1.3.1.3 | Integer32 (-100..45 | 255) | RO | ||||||||||||||||||
column · Integer32 (-100..45 | 255) · read-only · current This object shows the maximum output power in dBm including attenuator. Value -100 indicate that RAU Tx on is not possible due to power supply limitations. | |||||||||||||||||||||
| CxfRFRtpcSelectedOutputPower | 1.3.6.1.4.1.193.81.3.4.3.1.3.1.4 | Integer32 (-100..45 | 254) | RW | ||||||||||||||||||
column · Integer32 (-100..45 | 254) · read-write · current This object set/shows the selected output power in dBm including attenuator. Value 254 indicates that the selected power is set to maximum. Default value: 254 | |||||||||||||||||||||
| CxfRFAtpcMinOutputPower | 1.3.6.1.4.1.193.81.3.4.3.1.3.1.5 | Integer32 (-100..45 | 255) | RO | ||||||||||||||||||
column · Integer32 (-100..45 | 255) · read-only · current This object shows the minimum output power in dBm in ATPC. mode for radio contained in the radio terminal. | |||||||||||||||||||||
| CxfRFAtpcMaxOutputPower | 1.3.6.1.4.1.193.81.3.4.3.1.3.1.6 | Integer32 (-100..45 | 254) | RW | ||||||||||||||||||
column · Integer32 (-100..45 | 254) · read-write · current This object sets/shows the ATPC maximum output power in dBm for radio contained in the radio terminal. Value 254 indicates that the power is set to maximum. Default value: 254. | |||||||||||||||||||||
| CxfRFAtpcMinInputPowerFar | 1.3.6.1.4.1.193.81.3.4.3.1.3.1.7 | Integer32 (-99..-30 | 255) | RO | ||||||||||||||||||
column · Integer32 (-99..-30 | 255) · read-only · current This object shows the ATPC minimum input target power level for far end radio. | |||||||||||||||||||||
| CxfRFAtpcSelectedInputPowerFar | 1.3.6.1.4.1.193.81.3.4.3.1.3.1.8 | Integer32 (-99..-30) | RW | ||||||||||||||||||
column · Integer32 (-99..-30) · read-write · current This object sets/shows the ATPC selected input target level for far end radio. Default value: -30. | |||||||||||||||||||||
| CxfRFAttenuator | 1.3.6.1.4.1.193.81.3.4.3.1.3.1.9 | Integer32 (0..100) | RW | ||||||||||||||||||
column · Integer32 (0..100) · read-write · current This object sets/shows the value in dBm for fixed attenuator mounted in antenna. Default value: 0. | |||||||||||||||||||||
| CxfRFCurrentInputPower | 1.3.6.1.4.1.193.81.3.4.3.1.3.1.10 | Integer32 (-999..-200) | RO | -639 | |||||||||||||||||
column · Integer32 (-999..-200) · read-only · current This object shows RF input level = value/10 dBm. Domain: [-20.0 .. -99.9 dBm]. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CxfRFMaxInputPowerLast7Days | 1.3.6.1.4.1.193.81.3.4.3.1.3.1.11 | Integer32 (-999..-200 | 0) | RO | ||||||||||||||||||
column · Integer32 (-999..-200 | 0) · read-only · current This object shows maximum RF input level last 7 days. RF input level = value/10 dBm. Domain: [-99.9 ... -20.0 dBm]. 0 (zero) indicates invalid value. | |||||||||||||||||||||
| CxfRFMinInputPowerLast7Days | 1.3.6.1.4.1.193.81.3.4.3.1.3.1.12 | Integer32 (-999..-200 | 0) | RO | ||||||||||||||||||
column · Integer32 (-999..-200 | 0) · read-only · current This object shows minimum RF input level last 7 days. RF input level = value/10 dBm. Domain: [-99.9 ... -20.0 dBm]. 0 (zero) indicates invalid value. | |||||||||||||||||||||
| CxfRFMaxInputPowerSinceReset | 1.3.6.1.4.1.193.81.3.4.3.1.3.1.13 | Integer32 (-999..-200) | RO | ||||||||||||||||||
column · Integer32 (-999..-200) · read-only · current This object shows maximum RF input level since reset. RF input level = value/10 dBm. Domain: [-20.0 .. -99.9 dBm]. | |||||||||||||||||||||
| CxfRFMinInputPowerSinceReset | 1.3.6.1.4.1.193.81.3.4.3.1.3.1.14 | Integer32 (-999..-200) | RO | ||||||||||||||||||
column · Integer32 (-999..-200) · read-only · current This object shows minimum RF input level since reset. RF input level = value/10 dBm. Domain: [-20.0 .. -99.9 dBm]. | |||||||||||||||||||||
| CxfRFInputPowerReset | 1.3.6.1.4.1.193.81.3.4.3.1.3.1.15 | INTEGER | RW | ||||||||||||||||||
column · INTEGER · read-write · current This object reset the registers for the RF input level and All Time High level this seven days period and counters for the next seven days period of time Note. For protected rlMLE and rlXfMLE terminals this command will reset both Ra1 and Ra2 values. Near end access: read-write Far end access: read-write (Traffic Node only)
| |||||||||||||||||||||
| CxfRFInputAlarmThreshold | 1.3.6.1.4.1.193.81.3.4.3.1.3.1.16 | Integer32 (-99..-30) | RW | ||||||||||||||||||
column · Integer32 (-99..-30) · read-write · current This object shows RF input level threshold. Default value: -93. | |||||||||||||||||||||
| CxfRFOutputPower4QAM | 1.3.6.1.4.1.193.81.3.4.3.1.3.1.17 | Integer32 | RO | ||||||||||||||||||
column · Integer32 · read-only · current Output power for 4QAM. | |||||||||||||||||||||
| CxfRFOutputPower8QAM | 1.3.6.1.4.1.193.81.3.4.3.1.3.1.18 | Integer32 | RO | ||||||||||||||||||
column · Integer32 · read-only · current Output power for 8QAM. | |||||||||||||||||||||
| CxfRFOutputPower16QAM | 1.3.6.1.4.1.193.81.3.4.3.1.3.1.19 | Integer32 | RO | ||||||||||||||||||
column · Integer32 · read-only · current Output power for 16QAM. | |||||||||||||||||||||
| CxfRFOutputPower32QAM | 1.3.6.1.4.1.193.81.3.4.3.1.3.1.20 | Integer32 | RO | ||||||||||||||||||
column · Integer32 · read-only · current Output power for 32QAM. | |||||||||||||||||||||
| CxfRFOutputPower64QAM | 1.3.6.1.4.1.193.81.3.4.3.1.3.1.21 | Integer32 | RO | ||||||||||||||||||
column · Integer32 · read-only · current Output power for 64QAM. | |||||||||||||||||||||
| CxfRFOutputPower128QAM | 1.3.6.1.4.1.193.81.3.4.3.1.3.1.22 | Integer32 | RO | ||||||||||||||||||
column · Integer32 · read-only · current Output power for 128QAM. | |||||||||||||||||||||
| CxfRFOutputPower256QAM | 1.3.6.1.4.1.193.81.3.4.3.1.3.1.23 | Integer32 | RO | ||||||||||||||||||
column · Integer32 · read-only · current Output power for 256QAM. | |||||||||||||||||||||
| CxfRFOutputPower512QAM | 1.3.6.1.4.1.193.81.3.4.3.1.3.1.24 | Integer32 | RO | ||||||||||||||||||
column · Integer32 · read-only · current Output power for 512QAM. | |||||||||||||||||||||
| CxfRFAtpcFallbackOutputPower | 1.3.6.1.4.1.193.81.3.4.3.1.3.1.25 | Integer32 (-100..45 | 254) | RW | ||||||||||||||||||
column · Integer32 (-100..45 | 254) · read-write · current This object sets maximum output power in dBm in ATPCFallback mode for radio contained in the radio terminal. Value = 254 indicates that the power is set to maximum. Default value: 254. | |||||||||||||||||||||
| CxfRFAtpcFallbackEnable | 1.3.6.1.4.1.193.81.3.4.3.1.3.1.26 | ATPCFallbackEnable | RW | ||||||||||||||||||
column · ATPCFallbackEnable · read-write · current Enable/disable ATPCFallback. | |||||||||||||||||||||
| CxfRFAtpcFallbackTimer | 1.3.6.1.4.1.193.81.3.4.3.1.3.1.27 | Integer32 (1..60) | RW | ||||||||||||||||||
column · Integer32 (1..60) · read-write · current ATPC Fallback Timer specifies how long the output power can be at PATPC, MAX before ATPC fallback is triggered Default value: 15 min | |||||||||||||||||||||
| CxfRFOutputPower1024QAM | 1.3.6.1.4.1.193.81.3.4.3.1.3.1.28 | Integer32 | RO | ||||||||||||||||||
column · Integer32 · read-only · current Output power for 1024QAM. | |||||||||||||||||||||
| CxfRFMaxOutputPowerNotLimited | 1.3.6.1.4.1.193.81.3.4.3.1.3.1.29 | Integer32 | RO | ||||||||||||||||||
column · Integer32 · read-only · current Max output power in dBm including attenuator that the RAU can give if it is not power supply limited. | |||||||||||||||||||||
| CxfRFMaxOutputPowerNotPossible | 1.3.6.1.4.1.193.81.3.4.3.1.3.1.30 | INTEGER | RO | ||||||||||||||||||
column · INTEGER · read-only · current unknown(0)
isPossible(1) Max output power is possible due
to power supply limitations
isNotPossible(2) Max output power is not possible
due to power supply limitations
| |||||||||||||||||||||
| CxfRFCurrentInputPowerSdcMain | 1.3.6.1.4.1.193.81.3.4.3.1.3.1.31 | Integer32 (-999..-200 | 0) | RO | ||||||||||||||||||
column · Integer32 (-999..-200 | 0) · read-only · current This object shows RF input level for SDC Main path = value/10 dBm. Domain: [-20.0 .. -99.9 dBm]. 0 (zero) indicates invalid value (e.g. SDC not available). | |||||||||||||||||||||
| CxfRFCurrentInputPowerSdcDiv | 1.3.6.1.4.1.193.81.3.4.3.1.3.1.32 | Integer32 (-999..-200 | 0) | RO | ||||||||||||||||||
column · Integer32 (-999..-200 | 0) · read-only · current This object shows RF input level for SDC Diversity path = value/10 dBm. Domain: [-20.0 .. -99.9 dBm]. 0 (zero) indicates invalid value (e.g. SDC not available). | |||||||||||||||||||||
| CxfRFMeanInputPower1m | 1.3.6.1.4.1.193.81.3.4.3.1.3.1.33 | Integer32 (-999..-200 | 0) | RO | ||||||||||||||||||
column · Integer32 (-999..-200 | 0) · read-only · current This object shows RF input mean level for last minute. RF input level = value/10 dBm. Domain: [-99.9 ... -20.0 dBm] 0 (zero) indicates invalid value. | |||||||||||||||||||||
| CxfRFMaxOutputPowerLast7Days | 1.3.6.1.4.1.193.81.3.4.3.1.3.1.34 | Integer32 (-100..45 | 255) | RO | ||||||||||||||||||
column · Integer32 (-100..45 | 255) · read-only · current This object shows maximum RF output level last 7 days. RF output level = value dBm. Domain: [-100 ... 45 dBm] 255 indicates invalid value. | |||||||||||||||||||||
| CxfRFMinOutputPowerLast7Days | 1.3.6.1.4.1.193.81.3.4.3.1.3.1.35 | Integer32 (-100..45 | 255) | RO | ||||||||||||||||||
column · Integer32 (-100..45 | 255) · read-only · current This object shows minimum RF output level last 7 days. RF output level = value dBm. Domain: [-100 ... 45 dBm] 255 indicates invalid value. | |||||||||||||||||||||
| CxfRFMaxOutputPowerSinceReset | 1.3.6.1.4.1.193.81.3.4.3.1.3.1.36 | Integer32 (-100..45 | 255) | RO | ||||||||||||||||||
column · Integer32 (-100..45 | 255) · read-only · current This object shows maximum RF output level since reset RF output level = value dBm. Domain: [-100 ... 45 dBm] 255 indicates invalid value. | |||||||||||||||||||||
| CxfRFMinOutputPowerSinceReset | 1.3.6.1.4.1.193.81.3.4.3.1.3.1.37 | Integer32 (-100..45 | 255) | RO | ||||||||||||||||||
column · Integer32 (-100..45 | 255) · read-only · current This object shows minimum RF output level since reset RF output level = value dBm. Domain: [-100 ... 45 dBm] 255 indicates invalid value. | |||||||||||||||||||||
| CxfRFMaxMSELast7Days | 1.3.6.1.4.1.193.81.3.4.3.1.3.1.38 | Integer32 (-1000..1000 | 2000) | RO | ||||||||||||||||||
column · Integer32 (-1000..1000 | 2000) · read-only · current Indicate Max MSE level last 7 days. Input level = value/10 dB. Domain: [-100.0 ... 100.0 dB] 2000 indicates invalid value. | |||||||||||||||||||||
| CxfRFMinMSELast7Days | 1.3.6.1.4.1.193.81.3.4.3.1.3.1.39 | Integer32 (-1000..1000 | 2000) | RO | ||||||||||||||||||
column · Integer32 (-1000..1000 | 2000) · read-only · current Indicate Min MSE level last 7 days. Input level = value/10 dB. Domain: [-100.0 ... 100.0 dB] 2000 indicates invalid value. | |||||||||||||||||||||
| CxfRFMaxXPILast7Days | 1.3.6.1.4.1.193.81.3.4.3.1.3.1.40 | Integer32 (-1000..1000 | 2000) | RO | ||||||||||||||||||
column · Integer32 (-1000..1000 | 2000) · read-only · current Indicate Max Cross-Polar Interference (XPI) level last 7 days. Input level = value/10 dB. Domain: [-100.0 ... 100.0 dB] 2000 indicates invalid value. | |||||||||||||||||||||
| CxfRFMinXPILast7Days | 1.3.6.1.4.1.193.81.3.4.3.1.3.1.41 | Integer32 (-1000..1000 | 2000) | RO | ||||||||||||||||||
column · Integer32 (-1000..1000 | 2000) · read-only · current Indicate Min Cross-Polar Interference (XPI) level last 7 days. Input level = value/10 dB. Domain: [-100.0 ... 100.0 dB] 2000 indicates invalid value. | |||||||||||||||||||||
| CxfRFOutputPowerReset | 1.3.6.1.4.1.193.81.3.4.3.1.3.1.42 | INTEGER | RW | ||||||||||||||||||
column · INTEGER · read-write · current This object reset the registers for the RF output level and All Time High level this seven days period and counters for the next seven days period of time.
| |||||||||||||||||||||
| CxfRFBoosterGain | 1.3.6.1.4.1.193.81.3.4.3.1.3.1.43 | Integer32 (0..255) | RO | ||||||||||||||||||
column · Integer32 (0..255) · read-only · current Value of the Gain of the Booster | |||||||||||||||||||||
| CxfRFBoosterMaxInputPower | 1.3.6.1.4.1.193.81.3.4.3.1.3.1.44 | Integer32 (-100..35 | 255) | RO | ||||||||||||||||||
column · Integer32 (-100..35 | 255) · read-only · current Value of the Max Input Power admitted towards the Booster | |||||||||||||||||||||
| CxfRFBoosterCapability | 1.3.6.1.4.1.193.81.3.4.3.1.3.1.45 | BoosterCapability | RO | ||||||||||||||||||
column · BoosterCapability · read-only · current Value of Booster capability according to the system | |||||||||||||||||||||
| CxfRFBoosterProductNumber | 1.3.6.1.4.1.193.81.3.4.3.1.3.1.46 | DisplayString (SIZE (0..20)) | RW | ||||||||||||||||||
column · DisplayString (SIZE (0..20)) · read-write · current Product Number of the Booster connected to the specific RF IF | |||||||||||||||||||||
| CxfRFBoosterHWRevision | 1.3.6.1.4.1.193.81.3.4.3.1.3.1.47 | DisplayString (SIZE (0..20)) | RW | ||||||||||||||||||
column · DisplayString (SIZE (0..20)) · read-write · current HW Revision of the Booster connected to the specific RF IF | |||||||||||||||||||||
| TxfRAUCapabilityTable | 1.3.6.1.4.1.193.81.3.4.3.1.4 | NA | |||||||||||||||||||
table · not-accessible · current Table for RAU capability information. Table indexed with entPhysicalIndex and xfTermRowIndex. | |||||||||||||||||||||
| RxfRAUCapabilityEntry | 1.3.6.1.4.1.193.81.3.4.3.1.4.1 | NA | |||||||||||||||||||
row · not-accessible · current An entry in xfRAUCapabilityTable. | |||||||||||||||||||||
| CxfRAUChannelSpacing | 1.3.6.1.4.1.193.81.3.4.3.1.4.1.1 | RAUChannelSpacingCapability | RO | ||||||||||||||||||
column · RAUChannelSpacingCapability · read-only · current Channel spacing. ETSI: 3.5, 7, 14, 28, 40, 56 MHz ANSI: 10, 20, 30, 40, 50 MHz | |||||||||||||||||||||
| CxfRAUChannelModulation | 1.3.6.1.4.1.193.81.3.4.3.1.4.1.2 | RAUModulation | RO | ||||||||||||||||||
column · RAUModulation · read-only · current This object shows the modulation. Values: cqpsk(2) CQPSK qam16(3) 16-QAM qam128(4) 128-QAM qam32(5) 32-QAM qam64(6) 64-QAM qam4(7) 4-QAM qam8(8) 8-QAM qam256(9) 256-QAM qam512(10) 512-QAM qam1024(11) 1024-QAM | |||||||||||||||||||||
| CxfRAUSpectrumEfficiencyClass | 1.3.6.1.4.1.193.81.3.4.3.1.4.1.3 | RauSec | RO | ||||||||||||||||||
column · RauSec · read-only · current Spectrum Efficiency Class: other(1), unknown sec2(2), Spectrum eff. Class 2 sec3(3), Spectrum eff. Class 3 sec4L(4), Spectrum eff. Class 4L sec4H(5), Specturm eff. Class 4H sec5A(6), Spectrum eff. Class 5A sec5B(7), Spectrum eff. Class 5B sec6A(8), Spectrum eff. Class 6A sec6B(9) Spectrum eff. Class 6B | |||||||||||||||||||||
| CxfRAUCarrierMode | 1.3.6.1.4.1.193.81.3.4.3.1.4.1.4 | INTEGER | RO | ||||||||||||||||||
column · INTEGER · read-only · current Radio carrier mode.
| |||||||||||||||||||||
| TxfRAUSubBandTable | 1.3.6.1.4.1.193.81.3.4.3.1.5 | NA | |||||||||||||||||||
table · not-accessible · current Table for RAU Sub-Band index capability. Table indexed with entPhysicalIndex and xfRAUSubBandIndex. | |||||||||||||||||||||
| RxfRAUSubBandEntry | 1.3.6.1.4.1.193.81.3.4.3.1.5.1 | NA | |||||||||||||||||||
row · not-accessible · current An entry in xfRAUSubBandTable. | |||||||||||||||||||||
| CxfRAUSubBandIndex | 1.3.6.1.4.1.193.81.3.4.3.1.5.1.1 | Unsigned32 (1..255) | RO | ||||||||||||||||||
column · Unsigned32 (1..255) · read-only · current An index for the specific RAU Sub-Band available index range. | |||||||||||||||||||||
| CxfRAUSubBandRange | 1.3.6.1.4.1.193.81.3.4.3.1.5.1.2 | Unsigned32 (0..255) | RO | ||||||||||||||||||
column · Unsigned32 (0..255) · read-only · current This object shows the RAU Sub-Band available index range [0..255]. | |||||||||||||||||||||
| TxfRFSpectrumDiagTable | 1.3.6.1.4.1.193.81.3.4.3.1.6 | NA | |||||||||||||||||||
table · not-accessible · current Table for RF Spectrum Diagnostics control and status | |||||||||||||||||||||
| RxfRFSpectrumDiagEntry | 1.3.6.1.4.1.193.81.3.4.3.1.6.1 | NA | |||||||||||||||||||
| CxfRFSpectrumDiagAdminStatus | 1.3.6.1.4.1.193.81.3.4.3.1.6.1.1 | INTEGER | RW | ||||||||||||||||||
column · INTEGER · read-write · current RF Spectrum Diagnostics Admin Status
| |||||||||||||||||||||
| CxfRFSpectrumDiagOperStatus | 1.3.6.1.4.1.193.81.3.4.3.1.6.1.2 | INTEGER | RO | ||||||||||||||||||
column · INTEGER · read-only · current RF Spectrum Diagnostics Oper Status
| |||||||||||||||||||||
| CxfRFSpectrumDiagChannelScanEstTime | 1.3.6.1.4.1.193.81.3.4.3.1.6.1.3 | Unsigned32 (0..4294967295) | RO | ||||||||||||||||||
column · Unsigned32 (0..4294967295) · read-only · current Estimated time in seconds for scanning one Channel Spacing at current RX frequency | |||||||||||||||||||||
| CxfRFSpectrumDiagSubBandScanEstTime | 1.3.6.1.4.1.193.81.3.4.3.1.6.1.4 | Unsigned32 (0..4294967295) | RO | ||||||||||||||||||
column · Unsigned32 (0..4294967295) · read-only · current Estimated time in seconds for scanning full Sub Band of connected RAU | |||||||||||||||||||||
| CxfRFSpectrumDiagScanDate | 1.3.6.1.4.1.193.81.3.4.3.1.6.1.5 | DisplayString (SIZE (0..32)) | RO | ||||||||||||||||||
column · DisplayString (SIZE (0..32)) · read-only · current Date and time when scan (channel or sub-band) is completed, format: [YYYY]-[MM]-[DD]T[hh]:[mm]:[ss] | |||||||||||||||||||||
| CxfRFSpectrumDiagChannelSpacing | 1.3.6.1.4.1.193.81.3.4.3.1.6.1.6 | Unsigned32 (0..4294967295) | RO | ||||||||||||||||||
column · Unsigned32 (0..4294967295) · read-only · current Channel width measured by Spectrum Diagnostics | |||||||||||||||||||||
| CxfRFSpectrumDiagCurrRxFrequency | 1.3.6.1.4.1.193.81.3.4.3.1.6.1.7 | Unsigned32 (0..4294967295) | RO | ||||||||||||||||||
column · Unsigned32 (0..4294967295) · read-only · current Current value of Rx frequency | |||||||||||||||||||||
| CxfRFSpectrumDiagMinRxFrequency | 1.3.6.1.4.1.193.81.3.4.3.1.6.1.8 | Unsigned32 (0..4294967295) | RO | ||||||||||||||||||
column · Unsigned32 (0..4294967295) · read-only · current Minimum sub-band Rx frequency (RAU lower edge) | |||||||||||||||||||||
| CxfRFSpectrumDiagMaxRxFrequency | 1.3.6.1.4.1.193.81.3.4.3.1.6.1.9 | Unsigned32 (0..4294967295) | RO | ||||||||||||||||||
column · Unsigned32 (0..4294967295) · read-only · current Maximum sub-band Rx frequency (RAU upper edge) | |||||||||||||||||||||
| CxfRFSpectrumDiagIdxCompanion1 | 1.3.6.1.4.1.193.81.3.4.3.1.6.1.10 | Unsigned32 (0..4294967295) | RO | ||||||||||||||||||
column · Unsigned32 (0..4294967295) · read-only · current RF IF index for 1st companion carrier (0 if no companion) | |||||||||||||||||||||
| CxfRFSpectrumDiagIdxCompanion2 | 1.3.6.1.4.1.193.81.3.4.3.1.6.1.11 | Unsigned32 (0..4294967295) | RO | ||||||||||||||||||
column · Unsigned32 (0..4294967295) · read-only · current RF IF index for 2nd companion carrier (0 if no companion) | |||||||||||||||||||||
| CxfRFSpectrumDiagIdxCompanion3 | 1.3.6.1.4.1.193.81.3.4.3.1.6.1.12 | Unsigned32 (0..4294967295) | RO | ||||||||||||||||||
column · Unsigned32 (0..4294967295) · read-only · current RF IF index for 3rd companion carrier (0 if no companion) | |||||||||||||||||||||
| CxfRFSpectrumDiagProgress | 1.3.6.1.4.1.193.81.3.4.3.1.6.1.13 | Unsigned32 (0..100) | RO | ||||||||||||||||||
column · Unsigned32 (0..100) · read-only · current Completed percentage of Spectrum Diagnostics scan | |||||||||||||||||||||
| TxfRFSpectrumDiagResultTable | 1.3.6.1.4.1.193.81.3.4.3.1.7 | NA | |||||||||||||||||||
table · not-accessible · current Table of Spectrum Diagnostics scan results | |||||||||||||||||||||
| RxfRFSpectrumDiagResultEntry | 1.3.6.1.4.1.193.81.3.4.3.1.7.1 | NA | |||||||||||||||||||
row · not-accessible · current An entry in xfRFSpectrumDiagResultTable | |||||||||||||||||||||
| CxfRFSpectrumDiagResultIndex | 1.3.6.1.4.1.193.81.3.4.3.1.7.1.1 | Unsigned32 (0..4294967295) | RO | ||||||||||||||||||
column · Unsigned32 (0..4294967295) · read-only · current Spectrum Diagnostics Scan Result Index | |||||||||||||||||||||
| CxfRFSpectrumDiagResultRxFrequency | 1.3.6.1.4.1.193.81.3.4.3.1.7.1.2 | Unsigned32 (0..4294967295) | RO | ||||||||||||||||||
column · Unsigned32 (0..4294967295) · read-only · current Spectrum Diagnostics Scan Result Rx frequency in kHz | |||||||||||||||||||||
| CxfRFSpectrumDiagResultRxPower | 1.3.6.1.4.1.193.81.3.4.3.1.7.1.3 | Integer32 (-999..-200) | RO | ||||||||||||||||||
column · Integer32 (-999..-200) · read-only · current Spectrum Diagnostics Scan Result Rx Power value/10 dBm Domain: [-99.9 .. -20.0 dBm] | |||||||||||||||||||||
| TxfRfIfPowerTable | 1.3.6.1.4.1.193.81.3.4.3.1.8 | NA | |||||||||||||||||||
table · not-accessible · current Table for Radio Link RAU managed objects. Table indexed with ifIndex. | |||||||||||||||||||||
| RxfRfIfPowerEntry | 1.3.6.1.4.1.193.81.3.4.3.1.8.1 | NA | |||||||||||||||||||
| CxfRfSelectedMinOutputPower | 1.3.6.1.4.1.193.81.3.4.3.1.8.1.1 | RfOutputPower | RW | ||||||||||||||||||
column · RfOutputPower · read-write · current Minimum output power in dBm (selected by operator). Default value: 10 dBm. | |||||||||||||||||||||
| CxfRfSelectedMaxOutputPower | 1.3.6.1.4.1.193.81.3.4.3.1.8.1.2 | RfOutputPower | RW | ||||||||||||||||||
column · RfOutputPower · read-write · current Maximum output power in dBm (selected by operator). Default value: 10 dBm. | |||||||||||||||||||||
| CxfRfCurrentOutputPower | 1.3.6.1.4.1.193.81.3.4.3.1.8.1.3 | RfOutputPower | RO | 27 | |||||||||||||||||
column · RfOutputPower · read-only · current Current output power in dBm. 255 indicates invalid value. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CxfRfMinOutputPower | 1.3.6.1.4.1.193.81.3.4.3.1.8.1.4 | RfOutputPower | RO | ||||||||||||||||||
column · RfOutputPower · read-only · current Minimum output power in dBm (provided by RAU). 255 indicates invalid value. | |||||||||||||||||||||
| CxfRfMaxOutputPower | 1.3.6.1.4.1.193.81.3.4.3.1.8.1.5 | RfOutputPower | RO | ||||||||||||||||||
column · RfOutputPower · read-only · current Maximum output power in dBm (provided by RAU). 255 indicates invalid value. | |||||||||||||||||||||
| CxfRfAtpcTargetInputPowerFE | 1.3.6.1.4.1.193.81.3.4.3.1.8.1.6 | Integer32 (-99..-30) | RW | ||||||||||||||||||
column · Integer32 (-99..-30) · read-write · current ATPC target input power on Far End side. Default value: -30. | |||||||||||||||||||||
| CxfRfCurrentInputPower | 1.3.6.1.4.1.193.81.3.4.3.1.8.1.7 | RfInputPower | RO | -304 | |||||||||||||||||
column · RfInputPower · read-only · current RF input level. Value is in 1/10 dBm. Domain: [-20.0 .. -99.9 dBm]. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CxfRfMaxInputPowerLast7Days | 1.3.6.1.4.1.193.81.3.4.3.1.8.1.8 | RfInputPower | RO | ||||||||||||||||||
column · RfInputPower · read-only · current Maximum RF input level in the last 7 days. Value is in 1/10 dBm. Domain: [-99.9 ... -20.0 dBm]. 0 (zero) indicates an invalid value. | |||||||||||||||||||||
| CxfRfMinInputPowerLast7Days | 1.3.6.1.4.1.193.81.3.4.3.1.8.1.9 | RfInputPower | RO | ||||||||||||||||||
column · RfInputPower · read-only · current Minimum RF input level in the last 7 days. Value is in 1/10 dBm. Domain: [-99.9 ... -20.0 dBm]. 0 (zero) indicates an invalid value. | |||||||||||||||||||||
| CxfRfMaxInputPowerSinceReset | 1.3.6.1.4.1.193.81.3.4.3.1.8.1.10 | RfInputPower | RO | ||||||||||||||||||
column · RfInputPower · read-only · current Maximum RF input level since reset. Value is in 1/10 dBm. Domain: [-99.9 ... -20.0 dBm]. 0 (zero) indicates an invalid value. | |||||||||||||||||||||
| CxfRfMinInputPowerSinceReset | 1.3.6.1.4.1.193.81.3.4.3.1.8.1.11 | RfInputPower | RO | ||||||||||||||||||
column · RfInputPower · read-only · current Minimum RF input level since reset. Value is in 1/10 dBm. Domain: [-99.9 ... -20.0 dBm]. 0 (zero) indicates an invalid value. | |||||||||||||||||||||
| CxfRfInputPowerReset | 1.3.6.1.4.1.193.81.3.4.3.1.8.1.12 | INTEGER | RW | ||||||||||||||||||
column · INTEGER · read-write · current This object resets the registers for: - RF input power levels - input levels (i.e. RF power, MSE and XPI) in the next 7 days period of time.
| |||||||||||||||||||||
| CxfRfInputAlarmThreshold | 1.3.6.1.4.1.193.81.3.4.3.1.8.1.13 | Integer32 (-99..-30) | RW | ||||||||||||||||||
column · Integer32 (-99..-30) · read-write · current RF input level threshold. Default value: -93. | |||||||||||||||||||||
| CxfRfOutputPower4QAM | 1.3.6.1.4.1.193.81.3.4.3.1.8.1.14 | RfOutputPower | RO | ||||||||||||||||||
column · RfOutputPower · read-only · current Output power for 4QAM. 255 indicates invalid value. | |||||||||||||||||||||
| CxfRfOutputPower16QAM | 1.3.6.1.4.1.193.81.3.4.3.1.8.1.15 | RfOutputPower | RO | ||||||||||||||||||
column · RfOutputPower · read-only · current Output power for 16QAM. 255 indicates invalid value. | |||||||||||||||||||||
| CxfRfOutputPower32QAM | 1.3.6.1.4.1.193.81.3.4.3.1.8.1.16 | RfOutputPower | RO | ||||||||||||||||||
column · RfOutputPower · read-only · current Output power for 32QAM. 255 indicates invalid value. | |||||||||||||||||||||
| CxfRfOutputPower64QAM | 1.3.6.1.4.1.193.81.3.4.3.1.8.1.17 | RfOutputPower | RO | ||||||||||||||||||
column · RfOutputPower · read-only · current Output power for 64QAM. 255 indicates invalid value. | |||||||||||||||||||||
| CxfRfOutputPower128QAM | 1.3.6.1.4.1.193.81.3.4.3.1.8.1.18 | RfOutputPower | RO | ||||||||||||||||||
column · RfOutputPower · read-only · current Output power for 128QAM. 255 indicates invalid value. | |||||||||||||||||||||
| CxfRfOutputPower256QAM | 1.3.6.1.4.1.193.81.3.4.3.1.8.1.19 | RfOutputPower | RO | ||||||||||||||||||
column · RfOutputPower · read-only · current Output power for 256QAM. 255 indicates invalid value. | |||||||||||||||||||||
| CxfRfOutputPower512QAM | 1.3.6.1.4.1.193.81.3.4.3.1.8.1.20 | RfOutputPower | RO | ||||||||||||||||||
column · RfOutputPower · read-only · current Output power for 512QAM. 255 indicates invalid value. | |||||||||||||||||||||
| CxfRfOutputPower1024QAM | 1.3.6.1.4.1.193.81.3.4.3.1.8.1.21 | RfOutputPower | RO | ||||||||||||||||||
column · RfOutputPower · read-only · current Output power for 1024QAM. 255 indicates invalid value. | |||||||||||||||||||||
| CxfRfOutputPower2048QAM | 1.3.6.1.4.1.193.81.3.4.3.1.8.1.22 | RfOutputPower | RO | ||||||||||||||||||
column · RfOutputPower · read-only · current Output power for 2048QAM. 255 indicates invalid value. | |||||||||||||||||||||
| CxfRfOutputPower4096QAM | 1.3.6.1.4.1.193.81.3.4.3.1.8.1.23 | RfOutputPower | RO | ||||||||||||||||||
column · RfOutputPower · read-only · current Output power for 4096QAM. 255 indicates invalid value. | |||||||||||||||||||||
| CxfRfMaxOutputPowerNotLimited | 1.3.6.1.4.1.193.81.3.4.3.1.8.1.24 | RfOutputPower | RO | ||||||||||||||||||
column · RfOutputPower · read-only · current Max output power in dBm that the RAU can give if it is not power supply limited. 255 indicates invalid value. | |||||||||||||||||||||
| CxfRfMaxOutputPowerPossible | 1.3.6.1.4.1.193.81.3.4.3.1.8.1.25 | INTEGER | RO | ||||||||||||||||||
column · INTEGER · read-only · current possible(2): max output power is possible. notPossible(3): max output power is not possible, due to power supply limitations.
| |||||||||||||||||||||
| CxfRfMeanInputPower1m | 1.3.6.1.4.1.193.81.3.4.3.1.8.1.26 | Integer32 (-999..-200 | 0) | RO | ||||||||||||||||||
column · Integer32 (-999..-200 | 0) · read-only · current This object shows RF input mean level for last minute. RF input level = value/10 dBm. Domain: [-99.9 ... -20.0 dBm] 0 (zero) indicates invalid value. | |||||||||||||||||||||
| CxfRfMaxOutputPowerLast7Days | 1.3.6.1.4.1.193.81.3.4.3.1.8.1.27 | Integer32 (-100..45 | 255) | RO | ||||||||||||||||||
column · Integer32 (-100..45 | 255) · read-only · current This object shows maximum RF output level last 7 days. RF output level = value dBm. Domain: [-100 ... 45 dBm] 255 indicates invalid value. | |||||||||||||||||||||
| CxfRfMinOutputPowerLast7Days | 1.3.6.1.4.1.193.81.3.4.3.1.8.1.28 | Integer32 (-100..45 | 255) | RO | ||||||||||||||||||
column · Integer32 (-100..45 | 255) · read-only · current This object shows minimum RF output level last 7 days. RF output level = value dBm. Domain: [-100 ... 45 dBm] 255 indicates invalid value. | |||||||||||||||||||||
| CxfRfMaxOutputPowerSinceReset | 1.3.6.1.4.1.193.81.3.4.3.1.8.1.29 | Integer32 (-100..45 | 255) | RO | ||||||||||||||||||
column · Integer32 (-100..45 | 255) · read-only · current This object shows maximum RF output level since reset RF output level = value dBm. Domain: [-100 ... 45 dBm] 255 indicates invalid value. | |||||||||||||||||||||
| CxfRfMinOutputPowerSinceReset | 1.3.6.1.4.1.193.81.3.4.3.1.8.1.30 | Integer32 (-100..45 | 255) | RO | ||||||||||||||||||
column · Integer32 (-100..45 | 255) · read-only · current This object shows minimum RF output level since reset RF output level = value dBm. Domain: [-100 ... 45 dBm] 255 indicates invalid value. | |||||||||||||||||||||
| CxfRfOutputPowerReset | 1.3.6.1.4.1.193.81.3.4.3.1.8.1.31 | INTEGER | RW | ||||||||||||||||||
column · INTEGER · read-write · current This object reset the registers for the RF output level and All Time High level this seven days period and counters for the next seven days period of time.
| |||||||||||||||||||||
| CxfRfAvailableOutputPowerType | 1.3.6.1.4.1.193.81.3.4.3.1.8.1.32 | INTEGER | RO | ||||||||||||||||||
column · INTEGER · read-only · current This object reports the output power capability of the RAU: - standardPower - highPower
| |||||||||||||||||||||
| CxfRfSelectedOutputPowerType | 1.3.6.1.4.1.193.81.3.4.3.1.8.1.33 | INTEGER | RW | ||||||||||||||||||
column · INTEGER · read-write · current This object allows setting the output power type: - standardPower - highPower default: standardPower(2) When the type is set to highPower(3) a HP license key is required. If the license key is not present the capacity is limited to Basic Capacity. The output power can be configured as 'normal' without any impact from the HP license key (present or not). When the mode is standardPower(2) the availableMaxOutputPower is limited to 'max power' - 4 dB per modulation.
| |||||||||||||||||||||
| CxfRfTaps | 1.3.6.1.4.1.193.81.3.4.3.1.8.1.34 | INTEGER | RW | ||||||||||||||||||
column · INTEGER · read-write · current This object allows setting the Traffic Aware Power Saving. Default: disabled(3)
| |||||||||||||||||||||
| CxfRfCurrentInputPowerSdcMain | 1.3.6.1.4.1.193.81.3.4.3.1.8.1.35 | RfInputPower | RO | ||||||||||||||||||
column · RfInputPower · read-only · current This object shows RF input level for SDC Main path = value/10 dBm. Domain: [-20.0 .. -99.9 dBm]. 0 (zero) indicates invalid value (e.g. SDC not available). | |||||||||||||||||||||
| CxfRfCurrentInputPowerSdcDiv | 1.3.6.1.4.1.193.81.3.4.3.1.8.1.36 | RfInputPower | RO | ||||||||||||||||||
column · RfInputPower · read-only · current This object shows RF input level for SDC Diversity path = value/10 dBm. Domain: [-20.0 .. -99.9 dBm]. 0 (zero) indicates invalid value (e.g. SDC not available). | |||||||||||||||||||||
| CxfRfOutputPower8192QAM | 1.3.6.1.4.1.193.81.3.4.3.1.8.1.37 | RfOutputPower | RO | ||||||||||||||||||
column · RfOutputPower · read-only · current Output power for 8192QAM. 255 indicates invalid value. | |||||||||||||||||||||
| CxfRfOutputPower16384QAM | 1.3.6.1.4.1.193.81.3.4.3.1.8.1.38 | RfOutputPower | RO | ||||||||||||||||||
column · RfOutputPower · read-only · current Output power for 16384QAM. 255 indicates invalid value. | |||||||||||||||||||||
| CxfRfAtpcFallbackOutputPower | 1.3.6.1.4.1.193.81.3.4.3.1.8.1.39 | RfOutputPower | RW | ||||||||||||||||||
column · RfOutputPower · read-write · current This object sets output power (in dBm) in ATPCFallback mode, for radio contained in the Carrier Termination. 255 indicates invalid value. | |||||||||||||||||||||
| CxfRfAtpcFallbackEnable | 1.3.6.1.4.1.193.81.3.4.3.1.8.1.40 | ATPCFallbackEnable | RW | ||||||||||||||||||
column · ATPCFallbackEnable · read-write · current Enable/disable ATPCFallback. | |||||||||||||||||||||
| CxfRfAtpcFallbackTimer | 1.3.6.1.4.1.193.81.3.4.3.1.8.1.41 | Integer32 (1..60) | RW | ||||||||||||||||||
column · Integer32 (1..60) · read-write · current This object specifies how long the output power can be at (ATPC, MAX) before ATPC fallback is triggered. Default value: ETSI 15 min, ANSI 5 min. | |||||||||||||||||||||
| TxfRFIFCableMonitoringTable | 1.3.6.1.4.1.193.81.3.4.3.1.9 | NA | |||||||||||||||||||
table · not-accessible · current Table for Radiolink point-to-point radios RF IF Cable Monitoring managed objects. Table indexed with ifIndex. | |||||||||||||||||||||
| RxfRFIFCableMonitoringEntry | 1.3.6.1.4.1.193.81.3.4.3.1.9.1 | NA | |||||||||||||||||||
| CxfRFIFCMStatus | 1.3.6.1.4.1.193.81.3.4.3.1.9.1.1 | INTEGER | RW | ||||||||||||||||||
column · INTEGER · read-write · current This object manage IfCable Monitoring Status. Default value: disable(2). Near end access: read-write. Far end access: no access.
| |||||||||||||||||||||
| CxfRFOutlierAgc | 1.3.6.1.4.1.193.81.3.4.3.1.9.1.2 | INTEGER | RW | ||||||||||||||||||
column · INTEGER · read-write · current This object manage IfCable Outlier Alarm. Default value: disable(2). Near end access: read-write. Far end access: no access.
| |||||||||||||||||||||
| CxfRFOutlierSetTh | 1.3.6.1.4.1.193.81.3.4.3.1.9.1.3 | Unsigned32 (0..65535) | RW | ||||||||||||||||||
column · Unsigned32 (0..65535) · read-write · current This object handles Set Threshold for Outlier Alarm. 3 = Default value (0.3). - To calculate threshold use the following formula: SetTh/10. Default value: 3 Near end access: read-write. Far end access: no access. | |||||||||||||||||||||
| CxfRFOutlierCeaseTh | 1.3.6.1.4.1.193.81.3.4.3.1.9.1.4 | Unsigned32 (0..65535) | RW | ||||||||||||||||||
column · Unsigned32 (0..65535) · read-write · current This object handles Cease Threshold for Outlier Alarm. 2 = Default value (0.2). - To calculate threshold use the following formula: SetTh/10. Default value: 2 Near end access: read-write. Far end access: no access. | |||||||||||||||||||||
| CxfRFRangeAgc | 1.3.6.1.4.1.193.81.3.4.3.1.9.1.5 | INTEGER | RW | ||||||||||||||||||
column · INTEGER · read-write · current This object manage IfCable Range Alarm. Default value: disable(2). Near end access: read-write. Far end access: no access.
| |||||||||||||||||||||
| CxfRFRangeSetTh | 1.3.6.1.4.1.193.81.3.4.3.1.9.1.6 | Unsigned32 (0..65535) | RW | ||||||||||||||||||
column · Unsigned32 (0..65535) · read-write · current This object handles Set Threshold for Range Alarm. 30 = Default value (3). - To calculate threshold use the following formula: SetTh/10. Default value: 30 (dB/10) Near end access: read-write. Far end access: no access. | |||||||||||||||||||||
| CxfRFRangeCeaseTh | 1.3.6.1.4.1.193.81.3.4.3.1.9.1.7 | Unsigned32 (0..65535) | RW | ||||||||||||||||||
column · Unsigned32 (0..65535) · read-write · current This object handles Cease Threshold for Range Alarm. 20 = Default value (2). - To calculate threshold use the following formula: SetTh/10. Default value: 20 (dB/10) Near end access: read-write. Far end access: no access. | |||||||||||||||||||||
| CxfRFStddevAgc | 1.3.6.1.4.1.193.81.3.4.3.1.9.1.8 | INTEGER | RW | ||||||||||||||||||
column · INTEGER · read-write · current This object manage IfCable Stddev Alarm. Default value: disable(2). Near end access: read-write. Far end access: no access.
| |||||||||||||||||||||
| CxfRFStddevSetTh | 1.3.6.1.4.1.193.81.3.4.3.1.9.1.9 | Unsigned32 (0..65535) | RW | ||||||||||||||||||
column · Unsigned32 (0..65535) · read-write · current This object handles Set Threshold for Stddev Alarm. 50 = Default value (5). - To calculate threshold use the following formula: SetTh/10. Default value: 50 (dB/10) Near end access: read-write. Far end access: no access. | |||||||||||||||||||||
| CxfRFStddevCeaseTh | 1.3.6.1.4.1.193.81.3.4.3.1.9.1.10 | Unsigned32 (0..65535) | RW | ||||||||||||||||||
column · Unsigned32 (0..65535) · read-write · current This object handles Cease Threshold for Stddev Alarm. 20 = Default value (2). - To calculate threshold use the following formula: SetTh/10. Default value: 20 (dB/10) Near end access: read-write. Far end access: no access. | |||||||||||||||||||||
| CxfRFDegradationAgc | 1.3.6.1.4.1.193.81.3.4.3.1.9.1.11 | INTEGER | RW | ||||||||||||||||||
column · INTEGER · read-write · current This object manage IfCable Degradation Alarm. Default value: disable(2). Near end access: read-write. Far end access: no access.
| |||||||||||||||||||||
| CxfRFDegradationSetTh | 1.3.6.1.4.1.193.81.3.4.3.1.9.1.12 | Unsigned32 (0..65535) | RW | ||||||||||||||||||
column · Unsigned32 (0..65535) · read-write · current This object handles Set Threshold for Degradation Alarm. 2 = Default value (0.2). - To calculate threshold use the following formula: SetTh/10. Default value: 2 (dB/10) Near end access: read-write. Far end access: no access. | |||||||||||||||||||||
| CxfRFDegradationCeaseTh | 1.3.6.1.4.1.193.81.3.4.3.1.9.1.13 | Unsigned32 (0..65535) | RW | ||||||||||||||||||
column · Unsigned32 (0..65535) · read-write · current This object handles Cease Threshold for Degradation Alarm. 1 = Default value (0.1). - To calculate threshold use the following formula: SetTh/10. Default value: 1 (dB/10) Near end access: read-write. Far end access: no access. | |||||||||||||||||||||
| CxfRFMarginAgc | 1.3.6.1.4.1.193.81.3.4.3.1.9.1.14 | INTEGER | RW | ||||||||||||||||||
column · INTEGER · read-write · current This object manage IfCable Margin Alarm. Default value: disable(2). Near end access: read-write. Far end access: no access.
| |||||||||||||||||||||
| CxfRFMarginSetTh | 1.3.6.1.4.1.193.81.3.4.3.1.9.1.15 | Unsigned32 (0..65535) | RW | ||||||||||||||||||
column · Unsigned32 (0..65535) · read-write · current This object handles Set Threshold for Margin Alarm. 30 = Default value (3). - To calculate threshold use the following formula: SetTh/10. Default value: 30 (dB/10) Near end access: read-write. Far end access: no access. | |||||||||||||||||||||
| CxfRFMarginCeaseTh | 1.3.6.1.4.1.193.81.3.4.3.1.9.1.16 | Unsigned32 (0..65535) | RW | ||||||||||||||||||
column · Unsigned32 (0..65535) · read-write · current This object handles Cease Threshold for Margin Alarm. 60 = Default value (6). - To calculate threshold use the following formula: SetTh/10. Default value: 60 (dB/10) Near end access: read-write. Far end access: no access. | |||||||||||||||||||||
| CxfRFOutlierValue | 1.3.6.1.4.1.193.81.3.4.3.1.9.1.17 | Integer32 (-2147483647..2147483647) | RO | ||||||||||||||||||
column · Integer32 (-2147483647..2147483647) · read-only · current This object handles the value calculated on 24h for Outlier Alarm. 0 = Default value (0). - To calculate value use the following formula: Value/100. Default value: 0 Near end access: read-write. Far end access: no access. | |||||||||||||||||||||
| CxfRFRangeValue | 1.3.6.1.4.1.193.81.3.4.3.1.9.1.18 | Integer32 (-2147483647..2147483647) | RO | ||||||||||||||||||
column · Integer32 (-2147483647..2147483647) · read-only · current This object handles the value calculated on 24h for Range Alarm. 0 = Default value (0). - To calculate value use the following formula: Value/100. Default value: 0 (dB/100) Near end access: read-write. Far end access: no access. | |||||||||||||||||||||
| CxfRFStddevValue | 1.3.6.1.4.1.193.81.3.4.3.1.9.1.19 | Integer32 (-2147483647..2147483647) | RO | ||||||||||||||||||
column · Integer32 (-2147483647..2147483647) · read-only · current This object handles the value calculated on 24h for Stddev Alarm. 0 = Default value (0). - To calculate value use the following formula: Value/100. Default value: 0 (dB/100) Near end access: read-write. Far end access: no access. | |||||||||||||||||||||
| CxfRFDegradationValue | 1.3.6.1.4.1.193.81.3.4.3.1.9.1.20 | Integer32 (-2147483647..2147483647) | RO | ||||||||||||||||||
column · Integer32 (-2147483647..2147483647) · read-only · current This object handles the value calculated on 24h for Degradation Alarm. 0 = Default value (0). - To calculate value use the following formula: Value/100. Default value: 0 (dB/100) Near end access: read-write. Far end access: no access. | |||||||||||||||||||||
| CxfRFMarginValue | 1.3.6.1.4.1.193.81.3.4.3.1.9.1.21 | Integer32 (-2147483647..2147483647) | RO | ||||||||||||||||||
column · Integer32 (-2147483647..2147483647) · read-only · current This object handles the value calculated on 24h for Margin Alarm. 0 = Default value (0). - To calculate value use the following formula: Value/100. Default value: 0 (dB/100) Near end access: read-write. Far end access: no access. | |||||||||||||||||||||
| CxfRFOutlierTrigger | 1.3.6.1.4.1.193.81.3.4.3.1.9.1.22 | INTEGER | RO | ||||||||||||||||||
column · INTEGER · read-only · current This object manage IfCable Outlier Trigger. Default value: noSetThreshold(2). Near end access: read-write. Far end access: no access.
| |||||||||||||||||||||
| CxfRFRangeTrigger | 1.3.6.1.4.1.193.81.3.4.3.1.9.1.23 | INTEGER | RO | ||||||||||||||||||
column · INTEGER · read-only · current This object manage IfCable Range Trigger. Default value: noSetThreshold(2). Near end access: read-write. Far end access: no access.
| |||||||||||||||||||||
| CxfRFStddevTrigger | 1.3.6.1.4.1.193.81.3.4.3.1.9.1.24 | INTEGER | RO | ||||||||||||||||||
column · INTEGER · read-only · current This object manage IfCable Stddev Trigger. Default value: noSetThreshold(2). Near end access: read-write. Far end access: no access.
| |||||||||||||||||||||
| CxfRFDegradationTrigger | 1.3.6.1.4.1.193.81.3.4.3.1.9.1.25 | INTEGER | RO | ||||||||||||||||||
column · INTEGER · read-only · current This object manage IfCable Degradation Trigger. Default value: noSetThreshold(2). Near end access: read-write. Far end access: no access.
| |||||||||||||||||||||
| CxfRFMarginTrigger | 1.3.6.1.4.1.193.81.3.4.3.1.9.1.26 | INTEGER | RO | ||||||||||||||||||
column · INTEGER · read-only · current This object manage IfCable Margin Trigger. Default value: noSetThreshold(2). Near end access: read-write. Far end access: no access.
| |||||||||||||||||||||
| TxfSdcTable | 1.3.6.1.4.1.193.81.3.4.3.1.10 | NA | |||||||||||||||||||
table · not-accessible · current Table for SDC capabilities, setting and status. | |||||||||||||||||||||
| RxfSdcEntry | 1.3.6.1.4.1.193.81.3.4.3.1.10.1 | NA | |||||||||||||||||||
| CxfSdcCapability | 1.3.6.1.4.1.193.81.3.4.3.1.10.1.1 | INTEGER | RO | ||||||||||||||||||
column · INTEGER · read-only · current SDC capability, including both MMU and ODU.
| |||||||||||||||||||||
| CxfSdcAdminStatus | 1.3.6.1.4.1.193.81.3.4.3.1.10.1.2 | INTEGER | RW | ||||||||||||||||||
column · INTEGER · read-write · current SDC Admin Status.
| |||||||||||||||||||||
| CxfSdcOperStatus | 1.3.6.1.4.1.193.81.3.4.3.1.10.1.3 | INTEGER | RO | ||||||||||||||||||
column · INTEGER · read-only · current SDC Oper Status.
| |||||||||||||||||||||
| CxfSdcDadeControl | 1.3.6.1.4.1.193.81.3.4.3.1.10.1.4 | INTEGER | RW | ||||||||||||||||||
column · INTEGER · read-write · current SDC DADE procedure control.
| |||||||||||||||||||||
| CxfSdcDadeStatus | 1.3.6.1.4.1.193.81.3.4.3.1.10.1.5 | INTEGER | RO | ||||||||||||||||||
column · INTEGER · read-only · current SDC DADE procedure status.
| |||||||||||||||||||||
| CxfSdcPath | 1.3.6.1.4.1.193.81.3.4.3.1.10.1.6 | INTEGER | RW | ||||||||||||||||||
column · INTEGER · read-write · current SDC selected path (desired value).
| |||||||||||||||||||||
| CxfSdcOduDateTimeCalibration | 1.3.6.1.4.1.193.81.3.4.3.1.10.1.7 | DisplayString (SIZE (0..255)) | RO | ||||||||||||||||||
column · DisplayString (SIZE (0..255)) · read-only · current Date and time of the SDC DADE calibration for the ODU with serial number in xfSdcOduSerialNumber. Format: [YYYY]-[MM]-[DD]T[hh]:[mm]:[ss] (ISO 8601). | |||||||||||||||||||||
| CxfSdcOduSerialNumber | 1.3.6.1.4.1.193.81.3.4.3.1.10.1.8 | DisplayString (SIZE (0..255)) | RO | ||||||||||||||||||
column · DisplayString (SIZE (0..255)) · read-only · current Serial number of the ODU the current value of xfSdcOduDateTimeCalibration is referred to. | |||||||||||||||||||||
| CxfSdcGain | 1.3.6.1.4.1.193.81.3.4.3.1.10.1.9 | Integer32 (0..30) | RO | ||||||||||||||||||
column · Integer32 (0..30) · read-only · current SDC gain in dB/10. Domain: [0.0 .. 3.0 dB]. | |||||||||||||||||||||
| CxfSdcActualPath | 1.3.6.1.4.1.193.81.3.4.3.1.10.1.10 | INTEGER | RO | ||||||||||||||||||
column · INTEGER · read-only · current SDC actual path (current value).
| |||||||||||||||||||||
| CxfSdcDadeDelay | 1.3.6.1.4.1.193.81.3.4.3.1.10.1.11 | Integer32 (-2147483647..2147483647) | RO | ||||||||||||||||||
column · Integer32 (-2147483647..2147483647) · read-only · current DADE delay in nsec. | |||||||||||||||||||||
| NxfRadioLinkPtpRadioConformance | 1.3.6.1.4.1.193.81.3.4.3.2 | ||||||||||||||||||||
| NxfRadioLinkPtpRadioCompliances | 1.3.6.1.4.1.193.81.3.4.3.2.1 | ||||||||||||||||||||
| MxfRADIOLINKPTPRADIOFullCompliance | 1.3.6.1.4.1.193.81.3.4.3.2.1.1 | ||||||||||||||||||||
compliance · current The compliance statement for SNMP entities which implement everything. | |||||||||||||||||||||
| NxfRadioLinkPtpRadioGroups | 1.3.6.1.4.1.193.81.3.4.3.2.2 | ||||||||||||||||||||
| GxfRadioLinkPtpRadioCompleteGroup | 1.3.6.1.4.1.193.81.3.4.3.2.2.1 | ||||||||||||||||||||
group · current A collection of all current objects in this MIB module.
| |||||||||||||||||||||
Textual conventions
ATPCFallbackEnableINTEGERdisable(2)enable(3)other(1)ATPC fallback enable status.
BoosterCapabilityINTEGERboosterSupport(3)noBoosterSupport(2)other(1)Booster capabilities values codes.
RAUAtpcCapabilityINTEGERatpcCapabilityUnknown(4)doesNotExist(3)noAtpcSupport(2)other(1)supportsAtpc(5)This TC enumerates the ATPC capability.
RAUChannelSpacingCapabilityINTEGERchsp10MHz(9)chsp14MHz(2)chsp20MHz(3)chsp28MHz(4)chsp30MHz(5)chsp3500KHz(10)chsp40MHz(6)chsp50MHz(7)chsp56MHz(8)chsp60MHz(11)chsp7MHz(1)chspUnknown(0)Channel spacing capability.
RAUModCapabilityBitscqpsk(0)qam128(2)qam16(1)qam32(3)qam64(4)This TC enumerates the modulation capabilities. Modulation capabilities is indicated by 5 bits: bits 01234 00000 undetermined 00001 C-QPSK 00010 16-QAM 00011 C-QPSK & 16-QAM 00100 128-QAM 01000 32-QAM 10000 64-QAM ... 11111 C-QPSK & 16-QAM & 128-QAM & 32-QAM & 64-QAM
RAUModulationINTEGERcqpsk(2)other(1)qam1024(11)qam128(4)qam16(3)qam256(9)qam32(5)qam4(7)qam512(10)qam64(6)qam8(8)Type of modulation.
RAURfLoopAvailableINTEGERother(1)rfLoopAvailable(2)rfLoopNotAvailable(3)This TC enumerates the RF loop.
RFTxOperStatusINTEGERother(1)txOff(2)txOn(3)txStandby(4)This TC enumerates the Tx operational status.
RauSecINTEGERother(1)sec2(2)sec3(3)sec4H(5)sec4L(4)sec5A(6)sec5B(7)sec6A(8)sec6B(9)Spectrum Effeciency Class.
RfInputPowerInteger32 (-999..-200 | 0)RF Input power in dBm/10.
RfOutputPowerInteger32 (-100..45 | 255)RF output power in dBm.