CTRON-SSR-POLICY-MIB
Enterasys Networks Inc.This module defines a schema to control filters on a device capable of Layer 3 filters also called Access Control Lists (ACLs) and at layer 2. It may also be used to configure static IP routes that use other IP header fields in addition to destination IP address.
snmptranslate -m CTRON-SSR-POLICY-MIB -Tpsnmpwalk -v2c -c <community> -m CTRON-SSR-POLICY-MIB <host> 1.3.6.1.4.1.52.2501.1.210Imports
| CTRON-SSR-SMI-MIB | ssrMibs |
|---|---|
| Q-BRIDGE-MIB | dot1qVlanStaticEntry |
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP |
| SNMPv2-SMI | Bits, Counter32, Gauge32, Integer32, IpAddress, MODULE-IDENTITY, MibIdentifier, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, iso |
| SNMPv2-TC | DisplayString, MacAddress, PhysAddress, RowStatus, TEXTUAL-CONVENTION, TruthValue |
OID tree
| Name | OID | Type | Access | Status |
|---|---|---|---|---|
| NpolL3Group | 1.3.6.1.4.1.52.2501.1.12 | |||
| SpolAclServer | 1.3.6.1.4.1.52.2501.1.12.1 | TruthValue | RW | |
scalar · TruthValue · read-write · current This is true when Access Control Lists (ACLs) are defined by a
Policy Server else false.
At boot, this value is false. After the first valid set of any
policy object, the value changes to true. | ||||
| SpolAclNumber | 1.3.6.1.4.1.52.2501.1.12.2 | INTEGER (0..2147483647) | RO | |
scalar · INTEGER (0..2147483647) · read-only · current The number of Layer 3 Access Control Lists defined in the SSR. | ||||
| SpolAclLastChanged | 1.3.6.1.4.1.52.2501.1.12.3 | TimeTicks | RO | |
scalar · TimeTicks · read-only · current The time the Access Control List were last changed. | ||||
| TpolAclTable | 1.3.6.1.4.1.52.2501.1.12.4 | NA | ||
table · not-accessible · current A list of Access Control List entries. | ||||
| RpolAclEntry | 1.3.6.1.4.1.52.2501.1.12.4.1 | NA | ||
| CpolAclName | 1.3.6.1.4.1.52.2501.1.12.4.1.1 | DisplayString | RO | |
column · DisplayString · read-only · current The administratively assigned name to this static route entry. | ||||
| CpolAclItem | 1.3.6.1.4.1.52.2501.1.12.4.1.2 | INTEGER (0..256) | RO | |
column · INTEGER (0..256) · read-only · current This row's unique identifier within a given ACL set. Member of the ACL set are numbered from 1 to 256. If Item is set to 0, and rowStatus is destroy, all rows for this set are destroyed. | ||||
| CpolAclRestriction | 1.3.6.1.4.1.52.2501.1.12.4.1.3 | INTEGER | RW | |
column · INTEGER · read-write · current The permissions/restrictions given to this static route entry.
| ||||
| CpolAclProtocol | 1.3.6.1.4.1.52.2501.1.12.4.1.4 | SSRProtocol | RW | |
column · SSRProtocol · read-write · current The IETF protocol this ACL applies to. | ||||
| CpolAclSrcIp | 1.3.6.1.4.1.52.2501.1.12.4.1.5 | IpAddress | RW | |
column · IpAddress · read-write · current The source L3 IP Address this ACL applies to. | ||||
| CpolAclSrcMask | 1.3.6.1.4.1.52.2501.1.12.4.1.6 | IpAddress | RW | |
column · IpAddress · read-write · current The source L3 IP Mask this ACL Applies to. | ||||
| CpolAclDstIp | 1.3.6.1.4.1.52.2501.1.12.4.1.7 | IpAddress | RW | |
column · IpAddress · read-write · current The source L3 IP Address this ACL applies to. | ||||
| CpolAclDstMask | 1.3.6.1.4.1.52.2501.1.12.4.1.8 | IpAddress | RW | |
column · IpAddress · read-write · current The source L3 IP Mask this ACL Applies to. | ||||
| CpolAclTOS | 1.3.6.1.4.1.52.2501.1.12.4.1.9 | INTEGER (0..15) | RW | |
column · INTEGER (0..15) · read-write · current The source L3 IP Type of Service field. | ||||
| CpolAclSrcPort | 1.3.6.1.4.1.52.2501.1.12.4.1.10 | SSRsocketId | RW | |
column · SSRsocketId · read-write · current The source L3 IP source port/socket ACL applies to. | ||||
| CpolAclDstPort | 1.3.6.1.4.1.52.2501.1.12.4.1.11 | SSRsocketId | RW | |
column · SSRsocketId · read-write · current The source L3 IP destination port/socket ACL applies to. | ||||
| CpolAclSrcOperator | 1.3.6.1.4.1.52.2501.1.12.4.1.12 | SSRPortComparator | RW | |
column · SSRPortComparator · read-write · current polAclSrcPort is compared using this operator. | ||||
| CpolAclDstOperator | 1.3.6.1.4.1.52.2501.1.12.4.1.13 | SSRPortComparator | RW | |
column · SSRPortComparator · read-write · current polAclDstPort is compared using this operator. | ||||
| CpolAclSrcHighRange | 1.3.6.1.4.1.52.2501.1.12.4.1.14 | INTEGER (-1..65535) | RW | |
column · INTEGER (-1..65535) · read-write · current The high range source L3 IP port. Used only when SrcOperator == range. polAclSrcPort is used as the lower bounds of the range. | ||||
| CpolAclDstHighRange | 1.3.6.1.4.1.52.2501.1.12.4.1.15 | INTEGER (-1..65535) | RW | |
column · INTEGER (-1..65535) · read-write · current The high range destination L3 IP port. Used only when SrcOperator == range. polAclDstPort is used as the lower bounds of the range. | ||||
| CpolAclAuditTrail | 1.3.6.1.4.1.52.2501.1.12.4.1.16 | TruthValue | RW | |
column · TruthValue · read-write · current Flows matching this ACL are logged for Accounting when true. | ||||
| CpolAclCheckpoint | 1.3.6.1.4.1.52.2501.1.12.4.1.17 | INTEGER | RW | |
column · INTEGER · read-write · current How long to keep flow at which point a checkpoint should be done. A checkpoint may trigger earlier than this time should the maximum batch size be reached.
| ||||
| CpolAclRowStatus | 1.3.6.1.4.1.52.2501.1.12.4.1.18 | RowStatus | RW | |
column · RowStatus · read-write · current SNMP V2 RowStatus control for this table. | ||||
| SpolAclServiceNumber | 1.3.6.1.4.1.52.2501.1.12.5 | INTEGER (0..2147483647) | RO | |
scalar · INTEGER (0..2147483647) · read-only · current The number of Layer 3 Access Control Lists in service in the SSR. | ||||
| SpolAclServiceLastChanged | 1.3.6.1.4.1.52.2501.1.12.6 | TimeTicks | RO | |
scalar · TimeTicks · read-only · current The time the ACLs in service were last changed. | ||||
| TpolAclServiceTable | 1.3.6.1.4.1.52.2501.1.12.7 | NA | ||
table · not-accessible · current A list of ACL's currently in service. | ||||
| RpolAclServiceEntry | 1.3.6.1.4.1.52.2501.1.12.7.1 | NA | ||
row · not-accessible · current A record containing a Access Control Lists applied to Interfaces. | ||||
| CpolAclServiceIfIndex | 1.3.6.1.4.1.52.2501.1.12.7.1.1 | InterfaceIndex | RO | |
column · InterfaceIndex · read-only · current The ifIndex of the IP Interface the ACL is applied to. An SSR IP Interface has ifType 142 | ||||
| CpolAclName2 | 1.3.6.1.4.1.52.2501.1.12.7.1.2 | DisplayString | RO | |
column · DisplayString · read-only · current The name of the ACL applied to the particular port. | ||||
| CpolAclServiceDirection | 1.3.6.1.4.1.52.2501.1.12.7.1.3 | INTEGER | RW | |
column · INTEGER · read-write · current The direction the ACL is applied to the particular port.
| ||||
| CpolAclServiceRowStatus | 1.3.6.1.4.1.52.2501.1.12.7.1.6 | RowStatus | RW | |
column · RowStatus · read-write · current SNMP V2 RowStatus control for this table. | ||||
| SpolAclRemoteAllowed | 1.3.6.1.4.1.52.2501.1.12.9 | TruthValue | RO | |
scalar · TruthValue · read-only · current Remote Policy Configuration is allowed when true only local (to SSR) policy may be applied. | ||||
| SpolAclInterfaceNumber | 1.3.6.1.4.1.52.2501.1.12.10 | INTEGER (0..2147483647) | RO | |
scalar · INTEGER (0..2147483647) · read-only · current The number of Layer 3 Interfaces in service in the SSR. | ||||
| SpolAclInterfaceLastChanged | 1.3.6.1.4.1.52.2501.1.12.11 | TimeTicks | RO | |
scalar · TimeTicks · read-only · current The time the Interfaces in service were last changed with regard to policy. | ||||
| TpolAclInterfaceTable | 1.3.6.1.4.1.52.2501.1.12.12 | NA | ||
table · not-accessible · current A list of IP Interfaces in service and their policy status. Each IP Interface can be defined to use local static policy or remote dynamic policy in the config. | ||||
| RpolAclInterfaceEntry | 1.3.6.1.4.1.52.2501.1.12.12.1 | NA | ||
row · not-accessible · current A record containing a Access Control Lists applied to Interfaces. | ||||
| CpolAclInterfaceIfIndex | 1.3.6.1.4.1.52.2501.1.12.12.1.1 | InterfaceIndex | RO | |
column · InterfaceIndex · read-only · current The ifIndex of the IP Interface the ACL is applied to. | ||||
| CpolAclInterfaceDirection | 1.3.6.1.4.1.52.2501.1.12.12.1.2 | INTEGER | RO | |
column · INTEGER · read-only · current The direction the ACL is applied to the particular port.
| ||||
| CpolAclPolicyStatus | 1.3.6.1.4.1.52.2501.1.12.12.1.3 | INTEGER | RO | |
column · INTEGER · read-only · current Rules for what type of management can apply ACLs to a particular interface. If set to remote, then a Policy Manager via SNMP may change dynamically the ACLs applied to an interface. Note, ACLs applied dynamically are not maintained across system reboot. Use local ACLs to setup the basic rules then apply dynamic rules as necessary.
| ||||
| NpolL4Group | 1.3.6.1.4.1.52.2501.1.15 | |||
| SpolL4PolicyBasedRoutingEnabled | 1.3.6.1.4.1.52.2501.1.15.1 | TruthValue | RO | |
scalar · TruthValue · read-only · current The state of Policy Based Routing on this network element. | ||||
| SpolL4NumRouters | 1.3.6.1.4.1.52.2501.1.15.5 | INTEGER (0..10) | RO | |
scalar · INTEGER (0..10) · read-only · current The number of next hop routers currently available. | ||||
| SpolL4NextHopTableLastChange | 1.3.6.1.4.1.52.2501.1.15.10 | TimeTicks | RO | |
scalar · TimeTicks · read-only · current The value of sysUpTime when a row was last added or deleted from polL4NextHopTable. | ||||
| TpolL4NextHopTable | 1.3.6.1.4.1.52.2501.1.15.20 | NA | ||
table · not-accessible · current A list of next hop IP routers. | ||||
| RpolL4NextHopEntry | 1.3.6.1.4.1.52.2501.1.15.20.1 | NA | ||
row · not-accessible · current An entry contains the status of a next hop router.
| ||||
| CpolL4NextHopRouter | 1.3.6.1.4.1.52.2501.1.15.20.1.1 | IpAddress | RO | |
column · IpAddress · read-only · current The IP Address of the next hop router flow will be sent to. | ||||
| CpolL4NextHopState | 1.3.6.1.4.1.52.2501.1.15.20.1.2 | INTEGER | RO | |
column · INTEGER · read-only · current The current status of the polL4NextHopRouter. If no entry found when a policy route is activated, then arp for the request the state will be waitingForArp(2). If a reply is found the state will go to macAcquired(3) else noArpReply(4). If NextHop is not local, mac is actual nexthop router.
| ||||
| CpolL4NextHopPortOfExit | 1.3.6.1.4.1.52.2501.1.15.20.1.3 | InterfaceIndexOrZero | RO | |
column · InterfaceIndexOrZero · read-only · current IfIndex of port we learned this router on or else zero if not known. | ||||
| CpolL4NextHopMacAddress | 1.3.6.1.4.1.52.2501.1.15.20.1.4 | MacAddress | RO | |
column · MacAddress · read-only · current MAC Address of next hop router learned from ARP. | ||||
| CpolL4NextHopLastChange | 1.3.6.1.4.1.52.2501.1.15.20.1.5 | TimeTicks | RO | |
column · TimeTicks · read-only · current The value of sysUpTime when this polL4NextHopState changed. | ||||
| SpolL4lowControlTableLastChange | 1.3.6.1.4.1.52.2501.1.15.25 | TimeTicks | RO | |
scalar · TimeTicks · read-only · current The value of sysUpTime when a row was last added or deleted from polL4lowControlTable. | ||||
| SpolL4NumPolicies | 1.3.6.1.4.1.52.2501.1.15.26 | INTEGER (0..100000) | RO | |
scalar · INTEGER (0..100000) · read-only · current The number of policies currently available. | ||||
| TpolL4lowControlTable | 1.3.6.1.4.1.52.2501.1.15.30 | NA | ||
table · not-accessible · current Contains Control rows that indicate which flows have been redirected. As flows are aged out and recreated, these rules will enforce flow redirection policy. | ||||
| RpolL4lowControlEntry | 1.3.6.1.4.1.52.2501.1.15.30.1 | NA | ||
row · not-accessible · current This table is an ordered collection of route policies. For SSR, this maps to the command: ip-policy Name [permit|deny] acl acl-list | ||||
| CpolL4PolicyName | 1.3.6.1.4.1.52.2501.1.15.30.1.1 | DisplayString | NA | |
column · DisplayString · not-accessible · current A unique name for this flow policy. | ||||
| CpolL4PolicySequence | 1.3.6.1.4.1.52.2501.1.15.30.1.2 | Integer32 (1..65535) | NA | |
column · Integer32 (1..65535) · not-accessible · current The evaluation order of this object. When two objects have the same value, the value of the instance value decides which is evaluated first. than higher numbers. | ||||
| CpolL4PolicyInstance | 1.3.6.1.4.1.52.2501.1.15.30.1.3 | Integer32 (1..65535) | NA | |
column · Integer32 (1..65535) · not-accessible · current The sequence of this policy based route. Lower numbers have higher precedence than higher numbers. | ||||
| CpolL4PolicyType | 1.3.6.1.4.1.52.2501.1.15.30.1.4 | SSRFlowPolicyType | RC | |
column · SSRFlowPolicyType · read-create · current Controls if packets are forwarded or not for this policy. | ||||
| CpolL4PolicyAction | 1.3.6.1.4.1.52.2501.1.15.30.1.5 | SSRFlowPolicyAction | RC | |
column · SSRFlowPolicyAction · read-create · current Define when this policy should be used during normal packet forwarding process. | ||||
| CpolL4PolicyMatch | 1.3.6.1.4.1.52.2501.1.15.30.1.6 | SSRFlowPolicyAclList | RC | |
column · SSRFlowPolicyAclList · read-create · current Up to twenty (20) separate ACLs may be defined to match for this policy. This object is mandatory. Use active row from polAclTable. | ||||
| CpolL4PolicyNextHops | 1.3.6.1.4.1.52.2501.1.15.30.1.7 | SSRFlowNextHopList | RC | |
column · SSRFlowNextHopList · read-create · current Up to for IpAddresses may be specified to route data to next. Load balancing If more than one next hop ip address is specified, the default load balancing scheme is round robin. This object is mandatory. Use objects from polL4NextHopTable. | ||||
| CpolL4PolicyLoading | 1.3.6.1.4.1.52.2501.1.15.30.1.8 | SSRFlowLoadPolicy | RC | |
column · SSRFlowLoadPolicy · read-create · current When more than one next hop is defined and available, set loading policy here. | ||||
| CpolL4PolicyWatch | 1.3.6.1.4.1.52.2501.1.15.30.1.9 | TruthValue | RC | |
column · TruthValue · read-create · current When True, use icmp echo to actively maintain status of next hop. This is useful to prevent data sinks with static routes. | ||||
| CpolL4lowCreationTime | 1.3.6.1.4.1.52.2501.1.15.30.1.10 | TimeTicks | RO | |
column · TimeTicks · read-only · current The value of sysUpTime when policy went was created then activated. | ||||
| CpolL4lowActiveGates | 1.3.6.1.4.1.52.2501.1.15.30.1.11 | Gauge32 | RO | |
column · Gauge32 · read-only · current The number of currently active nexthop gateways. | ||||
| CpolL4lowAppliedTimes | 1.3.6.1.4.1.52.2501.1.15.30.1.12 | Counter32 | RO | |
column · Counter32 · read-only · current The number of times this policy was used. | ||||
| CpolL4lowControlStatus | 1.3.6.1.4.1.52.2501.1.15.30.1.13 | RowStatus | RC | |
column · RowStatus · read-create · current Entries in active state cause a flow to remain programmed with the next hop router specified.
If the next hop router goes down, the rowStatus will become inactive. New flows that match this
specification will assume this next hop router over any other route directive.
This assumes polL4PolicyBasedRouteState value is true. | ||||
| NpolL4GroupStats | 1.3.6.1.4.1.52.2501.1.15.35 | |||
| SpolL4lowLostRouters | 1.3.6.1.4.1.52.2501.1.15.35.1 | Counter32 | RO | |
scalar · Counter32 · read-only · current The count of times routers were disabled from NextHopTable due to lost contact. | ||||
| SpolL4lowControlTableActivates | 1.3.6.1.4.1.52.2501.1.15.35.2 | Counter32 | RO | |
scalar · Counter32 · read-only · current The count of successful activations of flow control policies made. | ||||
| SpolL4lowControlTableActivateFails | 1.3.6.1.4.1.52.2501.1.15.35.3 | Counter32 | RO | |
scalar · Counter32 · read-only · current The count of unsuccessful flow control policies made. | ||||
| SpolL4lowArpMappingChanges | 1.3.6.1.4.1.52.2501.1.15.35.4 | Counter32 | RO | |
scalar · Counter32 · read-only · current The count of mac to next hop IP address mapping changes affecting policy based route tables. | ||||
| SpolL4lowIcmpRedirects | 1.3.6.1.4.1.52.2501.1.15.35.16 | Counter32 | RO | |
scalar · Counter32 · read-only · current The count of next hop route redirects received that match a policy in the polL4lowControlTable. This can help to determine if bad route policies are in effect. | ||||
| SpolL4lowMatchAttempts | 1.3.6.1.4.1.52.2501.1.15.35.17 | Counter32 | RO | |
scalar · Counter32 · read-only · current The count of total number of policy based flow lookups made against policy based route table. | ||||
| NpolL2Group | 1.3.6.1.4.1.52.2501.1.16 | |||
| SpolL2FilterNumber | 1.3.6.1.4.1.52.2501.1.16.1 | INTEGER (0..2147483647) | RO | |
scalar · INTEGER (0..2147483647) · read-only · current The number of Layer 3 Access Control Lists defined in the SSR. | ||||
| SpolL2FilterLastChanged | 1.3.6.1.4.1.52.2501.1.16.2 | TimeTicks | RO | |
scalar · TimeTicks · read-only · current The time the Access Control List were last changed. | ||||
| TpolL2FilterTable | 1.3.6.1.4.1.52.2501.1.16.3 | NA | ||
table · not-accessible · current A list of Layer 2 filters. | ||||
| RpolL2FilterEntry | 1.3.6.1.4.1.52.2501.1.16.3.1 | NA | ||
| CpolL2FilterIndex | 1.3.6.1.4.1.52.2501.1.16.3.1.1 | INTEGER (1..65535) | NA | |
column · INTEGER (1..65535) · not-accessible · current A unique index into the table representing a single filter entry. This value will remain unique and the relationship between the index and the underlying filter is valid until the next reboot. | ||||
| CpolL2FilterDesc | 1.3.6.1.4.1.52.2501.1.16.3.1.2 | DisplayString (SIZE (0..25)) | RC | |
column · DisplayString (SIZE (0..25)) · read-create · current A string used to describe the filter. It should contain the creator IP address, and other descriptive information about the filter. It is recommended that names be unique within a given filter type. This object may not be modified if the associated. polL2FilterStatus object is equal to active(1). | ||||
| CpolL2FilterType | 1.3.6.1.4.1.52.2501.1.16.3.1.3 | INTEGER | RC | |
column · INTEGER · read-create · current The types of filters, as explained below.
static-entry
Based on the restrictions and the presence of
source, destination MAC address they can be of
three types :
source-static-entry - All frames with a source
address equal to srcMAC, coming through any of
the inPorts will be allowed/disallowed to go
to any port that is a member of the outPorts
list.
destination-static-entry - All frames with a
destination address equal to dstMAC, coming
through any of the inPorts will be allowed/
disallowed/forced to go to any port that is a
member of the outPorts list.
flow-static-entry - All frames with a source
address equal to srcMAC and a destination address
equal to dstMAC, coming through any of the inPorts
list will be allowed/disallowed to go to any port
that is a member of the outPorts list. Ports
must be in flow-bridging mode in order to use
filters with both src and dst mac specified.
address-filter
Based on the restrictions and the presence of
source, destination MAC address they can be of
three types :
source-address-filter - All frames with a source
address equal to srcMAC, coming through any of
the inPorts will be filtered out.
destination-address-filter - All frames with a
destination address equal to dstMAC, coming through
any of the inPorts will be filtered out.
flow-filter - All frames with a source address equal
to srcMAC and a destination address equal to dstMAC,
coming through any of the inPorts list will be
filtered out. Ports must be in flow mode in order
to set a filter using both source and destination
address.
port-address-lock
This locks a source address to a port. It allows
learning of srcMAC addresses only on any of the ports
in inPorts. The following objects are mandatory
and must be set by mgmt station to activate a row:
polL2FilterDesc, polL2FilterSrcMacAddr, polL2FilterInPorts
secure-port
This blocks all traffic in a given direction to a port.
Used with static entries, it is effective in allowing only
certain well defined source/destination mac addresses.
The following objects must be set by mgmt station to
activate an entry:
polL2FilterDesc, r, polL2FilterInPorts
This object may not be modified if the associated.
polL2FilterStatus object is equal to active(1).
| ||||
| CpolL2FilterRestrictions | 1.3.6.1.4.1.52.2501.1.16.3.1.4 | INTEGER | RC | |
column · INTEGER · read-create · current The first 3 restrictions, allow, disallow, force apply when the filterType is static-entry. When polL2FilterType is addressFilter or portAddressLock, this object does not apply. For securePort, the blockIngress, blockEgress values apply. This object may not be modified if the associated. polL2FilterStatus object is equal to active(1).
| ||||
| CpolL2FilterSrcMacAddr | 1.3.6.1.4.1.52.2501.1.16.3.1.5 | MacAddress | RC | |
column · MacAddress · read-create · current The source MAC address, which is present in case of a Flow, that has been learned by the switch. | ||||
| CpolL2FilterDstMacAddr | 1.3.6.1.4.1.52.2501.1.16.3.1.6 | MacAddress | RC | |
column · MacAddress · read-create · current The destination MAC address which has been learned. This object may not be modified if the associated. polL2FilterStatus object is equal to active(1). | ||||
| CpolL2FilterVlanId | 1.3.6.1.4.1.52.2501.1.16.3.1.7 | SSRVlanIndex | RC | |
column · SSRVlanIndex · read-create · current The VLAN the destination MAC address belongs to. The default VLAN is id 1 on SSR. This object may not be modified if the associated. polL2FilterStatus object is equal to active(1). | ||||
| CpolL2FilterInPorts | 1.3.6.1.4.1.52.2501.1.16.3.1.8 | SSRPortList | RC | |
column · SSRPortList · read-create · current The set of Ports to which this filter applies on input. This object may not be modified if the associated. polL2FilterStatus object is equal to active(1). | ||||
| CpolL2FilterOutPorts | 1.3.6.1.4.1.52.2501.1.16.3.1.9 | SSRPortList | RC | |
column · SSRPortList · read-create · current The set of ports to which this filter applies on output. This object may not be modified if the associated. polL2FilterStatus object is equal to active(1). | ||||
| CpolL2FilterCreationTime | 1.3.6.1.4.1.52.2501.1.16.3.1.10 | TimeTicks | RO | |
column · TimeTicks · read-only · current The value of sysUpTime when this filter was made active(1). | ||||
| CpolL2FilterStatus | 1.3.6.1.4.1.52.2501.1.16.3.1.11 | RowStatus | RC | |
column · RowStatus · read-create · current SMIv2 RowStatus control for this table. Use createAndWait or createAndGo to create a filter, use destroy to remove an entry or notInService to disengage a filter without destroying it. A row in the notReady state has not had all the mandatory objects set. | ||||
| TpolL2Dot1qVlanStaticTable | 1.3.6.1.4.1.52.2501.1.16.4 | NA | ||
table · not-accessible · current A table containing hardware specific VLAN behavior configuration information for VLANs created with the dot1qVlanStaticTable. Configuration information for each VLAN configured into the device by (local or network) management. | ||||
| RpolL2Dot1qVlanStaticEntry | 1.3.6.1.4.1.52.2501.1.16.4.1 | NA | ||
row · not-accessible · current An entry containing additional hardware specific objects for a dot1qVlanStaticEntry.
| ||||
| CpolL2Dot1qVlanStaticProtocols | 1.3.6.1.4.1.52.2501.1.16.4.1.1 | Bits | RC | |
column · Bits · read-create · current Specifies the types of traffic that will be forwarded on this VLAN. Protocols not set in this definition will be filtered. The types of protocols supported on this VLAN corresponds to the type option in the CLI command vlan create <vlan name> <type>. If no protocols are specified, all protocols are forwarded. This corresponds to the port-based CLI option. reserved(0) - this bit is reserved and has no defined behavior. bridged-protocols(1) - this VLAN supports all bridged protocols excluding IP and IPX. Includes appletalk(4), dec(5), sna(6), and ipv6(7) if none of these protocols are set. If any are set, only those that are set are included. ip(2) - this VLAN supports IP protocol. ipx(3) - this VLAN supports IPX protocol. appletalk(4) - this VLAN supports Appletalk protocol. dec(5) - this VLAN supports DEC protocol. sna(6) - this VLAN supports SNA protocol. ipv6(7) - this VLAN supports IPv6 protocol.
| ||||
| CpolL2Dot1qVlanStaticL4Bridging | 1.3.6.1.4.1.52.2501.1.16.4.1.2 | TruthValue | RC | |
column · TruthValue · read-create · current If this object has a value of false(2), the L4 Bridging feature is not enabled on this VLAN. If this object has a value of true(1), the L4 Bridging feature is enabled for this VLAN. This corresponds to the CLI command vlan enable l4-bridging. | ||||
| IpolicyMIB | 1.3.6.1.4.1.52.2501.1.210 | |||
identity This module defines a schema to control filters on a device capable of Layer 3 filters also called Access Control Lists (ACLs) and at layer 2. It may also be used to configure static IP routes that use other IP header fields in addition to destination IP address. | ||||
| NpolConformance | 1.3.6.1.4.1.52.2501.1.210.2 | |||
| NpolCompliances | 1.3.6.1.4.1.52.2501.1.210.2.1 | |||
| MpolComplianceV10 | 1.3.6.1.4.1.52.2501.1.210.2.1.1 | deprecated | ||
| MpolComplianceV11 | 1.3.6.1.4.1.52.2501.1.210.2.1.2 | deprecated | ||
compliance · deprecated The compliance statement for the policyMIB for version 1.1.
| ||||
| MpolComplianceV12 | 1.3.6.1.4.1.52.2501.1.210.2.1.3 | |||
| MpolComplianceV13 | 1.3.6.1.4.1.52.2501.1.210.2.1.4 | |||
| NpolGroups | 1.3.6.1.4.1.52.2501.1.210.2.2 | |||
| GpolGroupV10 | 1.3.6.1.4.1.52.2501.1.210.2.2.1 | deprecated | ||
group · deprecated A set of managed objects that make up version 1.0 of the SSR Flow Policy MIB.
| ||||
| GpolGroupV11 | 1.3.6.1.4.1.52.2501.1.210.2.2.2 | deprecated | ||
group · deprecated A set of managed objects that make up version 1.1 of the SSR Flow Policy MIB.
| ||||
| GpolGroupV12 | 1.3.6.1.4.1.52.2501.1.210.2.2.3 | |||
group · current A set of managed objects that make up version 1.2 of the SSR Flow Policy MIB.
| ||||
| GpolGroupV13 | 1.3.6.1.4.1.52.2501.1.210.2.2.4 | |||
group · current A set of managed objects that make up version 1.3 of the SSR Flow Policy MIB.
| ||||
Textual conventions
InterfaceIndexInteger32 (1..2147483647)Display hint:
dA unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub- layer must remain constant at least from one re- initialization of the entity's network management system to the next re-initialization.
InterfaceIndexOrZeroInteger32 (0..2147483647)Display hint:
dThis textual convention is an extension of the InterfaceIndex convention. The latter defines a greater than zero value used to identify an interface or interface sub-layer in the managed system. This extension permits the additional value of zero. the value zero is object-specific and must therefore be defined as part of the description of any object which uses this syntax. Examples of the usage of zero might include situations where interface was unknown, or when none or all interfaces need to be referenced.
SSRFlowLoadPolicyINTEGERfirstAvailable(2)roundRobin(3)round robin evenly distributes flows among the next hops. firstAvailable will make flows go to the first available next hop in the ordered list.
SSRFlowNextHopListOCTET STRING (SIZE (1..4096))A blank separated list of from one to four l4fNextHopRouter ipaddresses or the keyword null. Null represents the null interface
SSRFlowPolicyAclListOCTET STRING (SIZE (1..4096))A blank separated list of ACL names used to match flows against from the polAclTable. The keyword, everything, may be used to match all traffic. ASCII printable characters only
SSRFlowPolicyActionINTEGERpolicyAfterRouteLookup(2)policyBeforeRouteLookup(1)useOnlyPolicyLookup(3)When deciding when to apply policy there are three potential methods. policyBeforeRouteLookup provides a way to special case normal traffic patterns so that certain traffic can be routed according to policy. policyAfterRouteLookup is useful when a default route does not exist and the traffic to route does not match existing route tables. useOnlyPolicyLookup bypasses normal route lookup altogether.
SSRFlowPolicyTypeINTEGERdenyFlow(2)permitFlow(1)Type of Flow Policy. permitFlow allows matching traffic to be forwarded. denyFlow causes matching traffic to be discarded.
SSRPortComparatorINTEGEReq(2)gt(5)lt(4)neq(3)notused(1)range(6)Comparison operator used by ACL's to permit src/dst port addresses.
SSRPortListOCTET STRING (SIZE (0..255))List of ifIndexes that make up the ports to apply a layer 2 filter to. The ifIndexes are numbered sparsely starting from 1. An example string might be: 1,2,32 1,6,9, Each ifIndex must represent a physical port or link aggregation aka Smart Trunk ifType of propMultiplexor(54). Note ifIndexes may change across system resets per RFC 2233.SSRProtocolINTEGERicmp(4)igmp(5)ip(1)ipx(6)ipxrip(8)ipxsap(7)tcp(2)udp(3)Protocols supported by L3 ACLs.
SSRVlanIndexINTEGER (1..4100)An 802.1Q VLAN Identifier with same semantics as Q-BRIDGE-MIB VlanId. SSR uses Vid 1 for the default VLAN. All ports by default belong to this VLAN unless assigned to one or more user defined VLANs. A value of 4100 is used to match all VLANs. 4094 to 4099 are reserved local VLAN ids on the SSR.
SSRsocketIdINTEGER (0..65535)A TCP or UDP port or socket end point.