ARICENT-ISS-MIB
Future SoftwareThe MIB for ISS.
snmptranslate -m ARICENT-ISS-MIB -Tpsnmpwalk -v2c -c <community> -m ARICENT-ISS-MIB <host> 1.3.6.1.4.1.2076.81Imports
| IF-MIB | InterfaceIndex |
|---|---|
| INET-ADDRESS-MIB | InetAddress, InetAddressType |
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP |
| SNMPv2-SMI | Bits, Counter32, Integer32, IpAddress, MODULE-IDENTITY, MibIdentifier, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, enterprises, iso |
| SNMPv2-TC | DisplayString, MacAddress, PhysAddress, RowStatus, StorageType, TEXTUAL-CONVENTION, TruthValue |
OID tree
| Name | OID | Type | Access | Status | Example | ||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Iiss | 1.3.6.1.4.1.2076.81 | ||||||||||||||||||||
identity The MIB for ISS. | |||||||||||||||||||||
| NissNotifications | 1.3.6.1.4.1.2076.81.0 | ||||||||||||||||||||
| !issTrapConfigRestore | 1.3.6.1.4.1.2076.81.0.1 | ||||||||||||||||||||
notification · current This trap signifies the successful restoration of the saved configuration
| |||||||||||||||||||||
| !issMsrUpdateEventFail | 1.3.6.1.4.1.2076.81.0.2 | ||||||||||||||||||||
notification · current An MsrUpdateEventFail notification is sent when there is some failure in configuration change event received from SNMP Agent. issMsrFailedOid indicates the OID for which configuration change event has failed. issMsrFailedValue indicates the value of the corresponding OID for which configuration change event failure has occured.
| |||||||||||||||||||||
| !issAuditTrapMessage | 1.3.6.1.4.1.2076.81.0.3 | ||||||||||||||||||||
notification · current This trap notifies the erros on Audit file. | |||||||||||||||||||||
| !issTrapTemperature | 1.3.6.1.4.1.2076.81.0.4 | ||||||||||||||||||||
notification · current This notification is sent when the current temperature rises above or drops below the threshold. | |||||||||||||||||||||
| !issTrapCPUThreshold | 1.3.6.1.4.1.2076.81.0.5 | ||||||||||||||||||||
notification · current This notification is sent when CPU load exceeds the threshold value | |||||||||||||||||||||
| !issTrapPowerSupply | 1.3.6.1.4.1.2076.81.0.6 | ||||||||||||||||||||
notification · current This notification is sent when the current voltage drops below or exceeds the threshold value | |||||||||||||||||||||
| !issTrapRAMUsage | 1.3.6.1.4.1.2076.81.0.7 | ||||||||||||||||||||
notification · current This notification is sent when the RAM usage crosses the threshold percentage. | |||||||||||||||||||||
| !issTrapFlashUsage | 1.3.6.1.4.1.2076.81.0.8 | ||||||||||||||||||||
notification · current This notification is sent when the flash usage crosses the threshold. | |||||||||||||||||||||
| !issTrapFanStatus | 1.3.6.1.4.1.2076.81.0.9 | ||||||||||||||||||||
notification · current This notification is sent when the fan status is changed from down state to up state or vice versa.
| |||||||||||||||||||||
| !issLogTrapMessage | 1.3.6.1.4.1.2076.81.0.10 | ||||||||||||||||||||
notification · current This trap notifies the erros on System Log file. | |||||||||||||||||||||
| NissSystem | 1.3.6.1.4.1.2076.81.1 | ||||||||||||||||||||
| SissSwitchName | 1.3.6.1.4.1.2076.81.1.1 | DisplayString (SIZE (1..128)) | RW | SM-OS | |||||||||||||||||
scalar · DisplayString (SIZE (1..128)) · read-write · current System name used for identification of the device. Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissHardwareVersion | 1.3.6.1.4.1.2076.81.1.2 | DisplayString (SIZE (1..15)) | RO | 5.9.1 | |||||||||||||||||
scalar · DisplayString (SIZE (1..15)) · read-only · current Version number of the Hardware. Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissFirmwareVersion | 1.3.6.1.4.1.2076.81.1.3 | DisplayString (SIZE (1..15)) | RO | 6.7.2 | |||||||||||||||||
scalar · DisplayString (SIZE (1..15)) · read-only · current Version number of the Firmware. Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissDefaultIpAddrCfgMode | 1.3.6.1.4.1.2076.81.1.4 | INTEGER | RW | manual(1) | |||||||||||||||||
scalar · INTEGER · read-write · current Specifies the means by which the default interface in the device gets the IP address. If 'manual' mode is selected, the default interface takes the 'issDefaultIpAddr' configured in the system. If 'dynamic' mode is selected, the default interface gets the IP address through dynamic IP address configuration protocols such as RARP client, BootP client, DHCP Client, etc. If the system fails to get the IP address dynamically through all the above protocols, the default interface uses the 'issDefaultIpAddr' configured in the system.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissDefaultIpAddr | 1.3.6.1.4.1.2076.81.1.5 | IpAddress | RW | 10.250.0.110 | |||||||||||||||||
scalar · IpAddress · read-write · current Default IP Address of the system. This IP address, if modified, will take effect only when the configuration is stored & restored. Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissDefaultIpSubnetMask | 1.3.6.1.4.1.2076.81.1.6 | IpAddress | RW | 255.255.255.0 | |||||||||||||||||
scalar · IpAddress · read-write · current IP subnet mask for the default IP address. This subnet mask, if modified, will take effect only when the configuration is stored & restored. Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissEffectiveIpAddr | 1.3.6.1.4.1.2076.81.1.7 | IpAddress | RO | deprecated | 0.0.0.0 | ||||||||||||||||
scalar · IpAddress · read-only · deprecated Effective IP address of the switch to be used for contacting through SNMP interface or web interface. This IP address will be same as the default IP address if the device fails to get the IP address dynamically or the 'DefaultIpAddrCfgMode' is 'manual'. This IP address will be different from the default IP address if the device manages to get the IP address dynamically. In either condition, this is the effective IP address to be used for contacting the switch. Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissDefaultInterface | 1.3.6.1.4.1.2076.81.1.8 | DisplayString (SIZE (1..24)) | RW | Slot0/9 | |||||||||||||||||
scalar · DisplayString (SIZE (1..24)) · read-write · current Name of the default interface that can be used for communicating with the system for configuration through SNMP or WebInterface. The default interface, if modified, will take effect only when the configuration is stored & restored. Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissRestart | 1.3.6.1.4.1.2076.81.1.9 | TruthValue | RW | 2 | |||||||||||||||||
scalar · TruthValue · read-write · current This object allows the user to restart the Switch (i.e)the entire switch will operationally go down and start again. Setting a value of 'true' causes the switch to be restarted. When the switch operationally goes down, configuration save operation is initiated based on the configuration save option chosen. When the switch operationally come up, the saved configurations are restored based on the restore option chosen. Once the switch is restarted, the value of this object reverts to 'false'. Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissConfigSaveOption | 1.3.6.1.4.1.2076.81.1.10 | INTEGER | RW | startupConfig(4) | |||||||||||||||||
scalar · INTEGER · read-write · current Specifies whether the configurations of the switch has to be saved or not. The value 'noSave' specifies that the configurations need not be saved. The value 'flashSave' specifies that the configurations need to be saved in flash in the specified file name issConfigSaveFileName. The value 'remoteSave' specifies that the configurations need to be saved in specified remote system. The value 'startupConfig' specifies that the configurations need to be saved in flash in the 'Startup Configuration File'. When the issConfigIncrSaveFlag and the issConfigAutoSaveTrigger are set as true then the default value of issConfigSaveOption is startupConfig. When issConfigIncrSaveFlag is set as false or when issConfigAutoSaveTrigger is set as false then the default value of issConfigSaveOption is noSave.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissConfigSaveIpAddr | 1.3.6.1.4.1.2076.81.1.11 | IpAddress | RW | deprecated | 0.0.0.0 | ||||||||||||||||
scalar · IpAddress · read-write · deprecated IP Address of the remote system to which the switch configurations have to be saved. This object is valid only if 'issConfigSaveOption' is chosen to be 'remoteSave'. This object is deprecated, as this object supports only IPv4, this IP can be set through issConfigSaveIpvxAddr object and object issConfigSaveIpvxAddrType will be set to 1 i.e. IPv4 Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissConfigSaveFileName | 1.3.6.1.4.1.2076.81.1.12 | DisplayString (SIZE (1..128)) | RW | iss.conf | |||||||||||||||||
scalar · DisplayString (SIZE (1..128)) · read-write · current Name of the file in which the switch configurations are to be saved. This object is valid only if 'issConfigSaveOption' is chosen to be 'flashSave' or 'remoteSave'. Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissInitiateConfigSave | 1.3.6.1.4.1.2076.81.1.13 | TruthValue | RW | 2 | |||||||||||||||||
scalar · TruthValue · read-write · current When set as 'true' switch configurations save operation is
initiated.
As soon as the configuration save operation is completed, the value
of this object reverts back to 'false'.
All the configurations made via the three interfaces
viz.
-> commandline interface
-> Web Interface
-> SNMP interface
are saved either in 'Startup Configuration File' in the flash or
in the specified 'issConfigSaveFileName' in the flash or
in the chosen remote system, depending upon 'ConfigSaveOption'.Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissConfigSaveStatus | 1.3.6.1.4.1.2076.81.1.14 | INTEGER | RO | notInitiated(4) | |||||||||||||||||
scalar · INTEGER · read-only · current Status of configuration save operation.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissConfigRestoreOption | 1.3.6.1.4.1.2076.81.1.15 | INTEGER | RW | restore(2) | |||||||||||||||||
scalar · INTEGER · read-write · current Specifies whether the switch configurations have to be restored or not. The value 'noRestore' specifies that the switch configurations need not be restored when the system is restarted. The value 'restore' specifies that the configurations need to be restored from the 'Startup Configuration File' in the flash when the system is restarted.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissConfigRestoreIpAddr | 1.3.6.1.4.1.2076.81.1.16 | IpAddress | RW | deprecated | 10.0.0.2 | ||||||||||||||||
scalar · IpAddress · read-write · deprecated IP Address of the remote system from where the switch configurations have to be downloaded to the 'Startup Configuration File' in the flash. This object is deprecated, as this object supports only IPv4, this IP can be set through issConfigRestoreIpvxAddr object and object issConfigRestoreAddrType will be set to 1 i.e. IPv4 Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissConfigRestoreFileName | 1.3.6.1.4.1.2076.81.1.17 | DisplayString (SIZE (1..128)) | RW | iss.conf | |||||||||||||||||
scalar · DisplayString (SIZE (1..128)) · read-write · current The configuration file name in the remote system which has to be downloaded to the 'Startup Configuration File' in the flash. Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissInitiateConfigRestore | 1.3.6.1.4.1.2076.81.1.18 | TruthValue | RW | 2 | |||||||||||||||||
scalar · TruthValue · read-write · current When set as 'true', the switch configurations will be downloaded from the specified remote system to the 'Startup Configuration File' in the flash. As soon as the configuration download operation is completed, the value of this object reverts back to 'false'. Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissConfigRestoreStatus | 1.3.6.1.4.1.2076.81.1.19 | INTEGER | RO | restoreSuccessful(2) | |||||||||||||||||
scalar · INTEGER · read-only · current The status of the switch configuration restore operation.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissDlImageFromIp | 1.3.6.1.4.1.2076.81.1.20 | IpAddress | RW | deprecated | 0.0.0.0 | ||||||||||||||||
scalar · IpAddress · read-write · deprecated The Ip Address of machine from where the image has to be downloaded. This object is deprecated, as this object supports only IPv4, this IP can be set through issDlImageFromIpvxAddr object and object issDlImageFromIpAddrType will be set to 1 i.e. IPv4 Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissDlImageName | 1.3.6.1.4.1.2076.81.1.21 | DisplayString (SIZE (1..128)) | RW | iss.exe | |||||||||||||||||
scalar · DisplayString (SIZE (1..128)) · read-write · current The image name which is to be downloaded to the switch. Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissInitiateDlImage | 1.3.6.1.4.1.2076.81.1.22 | TruthValue | RW | 2 | |||||||||||||||||
scalar · TruthValue · read-write · current Initiates the Image Download operation. Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissLoggingOption | 1.3.6.1.4.1.2076.81.1.23 | INTEGER | RW | console(1) | |||||||||||||||||
scalar · INTEGER · read-write · current The Logging option specifying whether the logging is to be done at console or to a file(system buffer) in the system. Flash specifies the logging of traces into a file.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissUploadLogFileToIp | 1.3.6.1.4.1.2076.81.1.24 | IpAddress | RW | deprecated | 0.0.0.0 | ||||||||||||||||
scalar · IpAddress · read-write · deprecated The Ip Address of machine to which the log file is to be uploaded. This object is deprecated, as this object supports only IPv4, this IP can be set through issUploadLogFileToIpvxAddr object and object issUploadLogFileToAddrType will be set to 1 i.e. IPv4 Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissLogFileName | 1.3.6.1.4.1.2076.81.1.25 | DisplayString (SIZE (1..128)) | RW | iss.log | |||||||||||||||||
scalar · DisplayString (SIZE (1..128)) · read-write · current The file name to be used for uploading the logs from 'file' to the remote system. This object is useful only when the 'LogOption' is chosen as 'file'. Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissInitiateUlLogFile | 1.3.6.1.4.1.2076.81.1.26 | TruthValue | RW | 2 | |||||||||||||||||
scalar · TruthValue · read-write · current Initiates uploading of Log File to the specified IP address in 'issUploadLogFileToIp'. The logs will be uploaded in the specified 'issLogFileName'. Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissRemoteSaveStatus | 1.3.6.1.4.1.2076.81.1.27 | INTEGER | RO | notInitiated(4) | |||||||||||||||||
scalar · INTEGER · read-only · current Status of remote save operation.
The remote save operation could be a
a) configuration file save to remote system
b) log file upload to remote system.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissDownloadStatus | 1.3.6.1.4.1.2076.81.1.28 | INTEGER | RO | notInitiated(4) | |||||||||||||||||
scalar · INTEGER · read-only · current The status of the Image download operation to the switch.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissSysContact | 1.3.6.1.4.1.2076.81.1.29 | DisplayString (SIZE (1..50)) | RW | deprecated | [email protected] | ||||||||||||||||
scalar · DisplayString (SIZE (1..50)) · read-write · deprecated The textual identification of the contact person for this managed node, together with information on how to contact this person. If no contact information is known, the value is the zero-length string. Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissSysLocation | 1.3.6.1.4.1.2076.81.1.30 | DisplayString (SIZE (1..50)) | RW | deprecated | ARICENT | ||||||||||||||||
scalar · DisplayString (SIZE (1..50)) · read-write · deprecated The physical location of this node (e.g., `telephone closet, 3rd floor'). If the location is unknown, the value is the zero-length string. Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissLoginAuthentication | 1.3.6.1.4.1.2076.81.1.31 | INTEGER | RW | deprecated | local(1) | ||||||||||||||||
scalar · INTEGER · read-write · deprecated Configures the mechanism by which the user login has to be authenticated
for accessing the GUI to manage the switch. Authentication is done
either locally or in the remote side through a RADIUS Server or TACACS.
If Authentication is configured as radiusLocal or tacacsLocal then
Local authentication provides a back door or a secondary option
for authentication if the server fails.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissSwitchBaseMacAddress | 1.3.6.1.4.1.2076.81.1.32 | MacAddress | RW | 00:b0:ac:41:70:2a | |||||||||||||||||
scalar · MacAddress · read-write · current Ethernet address (base address) of the Switch. This base Mac Address, if modified, will take effect only when the Switch is restarted. Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissOOBInterface | 1.3.6.1.4.1.2076.81.1.33 | TruthValue | RO | 2 | |||||||||||||||||
scalar · TruthValue · read-only · current Indicates wheteher OOB Interface Exists in the System Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissSwitchDate | 1.3.6.1.4.1.2076.81.1.34 | DisplayString (SIZE (1..40)) | RW | 06 01 03 22:41:24 2025 (UTC +00:00) | |||||||||||||||||
scalar · DisplayString (SIZE (1..40)) · read-write · current The date is configured in the switch in the format, Hours:Minutes:Seconds Day Month Year e.g 19:10:31 11 08 2005 01-12 Month - beginning from January to December The railway time 00 to 24 hours can be configured and displayed. The Display of the date is in the format , WeekDay Month Day Hours:Minutes:Seconds Year e.g 04 09 21 18:11:30 2005 01-07 WeekDay - beginning from Sunday to Saturday 01-12 Month - beginning from January to December Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissNoCliConsole | 1.3.6.1.4.1.2076.81.1.35 | TruthValue | RW | 1 | |||||||||||||||||
scalar · TruthValue · read-write · current Indicates whether the CLI console prompt will be made available to the user for the session through serial console. When set to TRUE CLI prompt will be available in serial console, when set to FALSE CLI prompt will NOT be available in serial console session, for the value to take effect, the switch must be restarted, the value does not affect the availability of ISS CLI prompt in sessions established through Telnet. Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissDefaultIpAddrAllocProtocol | 1.3.6.1.4.1.2076.81.1.36 | INTEGER | RW | dhcp(2) | |||||||||||||||||
scalar · INTEGER · read-write · current Specifies the protocol to be used to obtain IP address for this interface. This object is valid only when issDefaultIpAddrCfgMode is set to dynamic (2). Currently rarp (1) option is not supported.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissHttpPort | 1.3.6.1.4.1.2076.81.1.37 | Integer32 (0..65535) | RW | 80 | |||||||||||||||||
scalar · Integer32 (0..65535) · read-write · current The port to be used by the hosts/PC to configure ISS using the Web Interface The HTTP server must be disabled before this configuration is done Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissHttpStatus | 1.3.6.1.4.1.2076.81.1.38 | INTEGER | RW | enable(1) | |||||||||||||||||
scalar · INTEGER · read-write · current This object is for enabling or disabling HTTP in the system.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissConfigRestoreFileVersion | 1.3.6.1.4.1.2076.81.1.39 | DisplayString (SIZE (1..12)) | RO | 2.50 | |||||||||||||||||
scalar · DisplayString (SIZE (1..12)) · read-only · current Config Restoration file version. This version will be compared in each reboot against version stored in restoration file. Restoration will occur only if the first field in restoration file is this OID and the RestoreFileVersion value also matches. Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissDefaultRmIfName | 1.3.6.1.4.1.2076.81.1.40 | DisplayString (SIZE (1..23)) | RW | lo | |||||||||||||||||
scalar · DisplayString (SIZE (1..23)) · read-write · current Name of the default RM interface that can be used for communication between the Active and Standby nodes for providing redundancy support.The default RM interface, if modified, will take effect only when the switch is restarted Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissDefaultVlanId | 1.3.6.1.4.1.2076.81.1.41 | Integer32 (1..4094) | RW | 1 | |||||||||||||||||
scalar · Integer32 (1..4094) · read-write · current The Default VLAN Identifier to be used at system startup. The VLAN Module creates this vlan as the default vlan. The Default VLAN Identifier, if modified, will take effect only when the switch is restarted. It is not advisable to change the default VLAN ID when some configurations are already saved. Once the Default VLAN Id is configured, the switch has to be restarted before saving any configuration. Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissNpapiMode | 1.3.6.1.4.1.2076.81.1.42 | DisplayString (SIZE (1..15)) | RW | | |||||||||||||||||
scalar · DisplayString (SIZE (1..15)) · read-write · current The Mode of NPAPI Processing. It can be 1. Synchronous, 2. Asynchronous. Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissConfigAutoSaveTrigger | 1.3.6.1.4.1.2076.81.1.43 | TruthValue | RW | 1 | |||||||||||||||||
scalar · TruthValue · read-write · current When set as 'true', automatic save operation is enabled. i.e., every
configuration is saved automatically.
When set as 'false', automatic save operation is disabled. i.e.,
configuration done will not be save automatically.
IncrSave is ON : auto save can be enabled /disabled in the system.
IncrSave is OFF : auto save can be enabled /disabled in the system,
No effect in the system behaviour(in this case no
update trigger is generated towards MSR).
============================================================================
issConfig issConfig
incrSaveFlag AutoSaveOption Behaviour
============================================================================
TRUE TRUE Data is added to RB Tree and based on save option
data is added to remote/local incremental file.
TRUE FALSE Data is added to RB tree only.
FALSE xx in this case no update trigger is generated towards
MSR.
============================================================================
To enable issConfigAutoSaveTrigger, the issConfigIncrSaveFlag has to be
enabled.
The configuration update to issConfigIncrSaveFlag will become applicable
only after switch restart.
When issConfigIncrSaveFlag is enabled, the configuration of
issConfigAutoSaveTrigger will be immediately reflected in the system.Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissConfigIncrSaveFlag | 1.3.6.1.4.1.2076.81.1.44 | TruthValue | RW | 1 | |||||||||||||||||
scalar · TruthValue · read-write · current Indicates whether SNMP Update Trigger for Incremental Save shall be generated or not.
'True' value implies that the update trigger shall be generated each time a nmhSet
operation is successful.
'False' value implies that the update trigger shall not be generated at all.
Following table explains the combinations of various configurations
============================================================================
issConfig issConfig issConfig
IncrSaveFlag AutoSaveTrigger SaveOption Behaviour
============================================================================
TRUE TRUE Remote Save tftp to remote (on every update trigger)
TRUE FALSE Remote Save tftp to remote (operator triggered)
FALSE xx Remote Save tftp to remote (operator triggered)
TRUE TRUE Flash Save save to local (on every update trigger)
TRUE FALSE Flash Save save to local (operator triggered)
FALSE xx Flash Save save to local (operator triggered)
TRUE TRUE No Save Data added to RB Tree
TRUE FALSE No Save Data added to RB Tree
FALSE xx No Save No Update trigger is sent to MSR
============================================================================
The configuration of the issConfigIncrSaveFlag object from true to false
or vice versa will be used only after switch restart.
As the auto save of configurations cannot be used when the
issConfigIncrSaveFlag is set to false, the issConfigAutoSaveTrigger
has to be set to false before setting the issConfigIncrSaveFlag
to false.Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissConfigRollbackFlag | 1.3.6.1.4.1.2076.81.1.45 | INTEGER | RW | enabled(2) | |||||||||||||||||
scalar · INTEGER · read-write · current Indicates whether SNMP Rollback feature is enabled or disabled. 'enabled' value implies that failure in set operation for any varbind will result in rollback of all varbinds whose value has been set in this SET PDU 'disabled' value implies that failure in set operation will simply return error.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissConfigSyncUpOperation | 1.3.6.1.4.1.2076.81.1.46 | INTEGER | RW | syncup(1) | |||||||||||||||||
scalar · INTEGER · read-write · current Indicates that sync operation is to be performed. Incremental save OFF: RB tree, incremental file/buffer are not present in the system, sync operation is not allowed in the system. Incremental save ON : On receiving this event, MSR deletes the data present in the RB tree and configuration data at MSR shall be made In sync with data store at protocols. Following table explains the combinations of various configurations ============================================================================ issConfig issConfig IncrSaveFlag SaveOption Behaviour ============================================================================ TRUE Remote Save RB Tree data made in sync with the data stored at protocols, same data Is updated at remote system, incremental file (at remote) is emptied. TRUE Local Save RB Tree data made in sync with the data stored at protocols, same data Is updated in local configuration file and incremental file (issinc.conf) is emptied. FALSE xx Event is not allowed in the system, MSR returns failure. ============================================================================
Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissFrontPanelPortCount | 1.3.6.1.4.1.2076.81.1.47 | Integer32 | RW | 10 | |||||||||||||||||
scalar · Integer32 · read-write · current The object defines the number of physical ports configured in a device for the purpose of switching/routing. The value of the object should not exceed system defined MAX physical interfaces, when the configured value is less than the MAX physical interfaces, the difference in port count shall be used for stacking purpose only when the stacking object issColdStandbyStacking is enabled else the ports are considered as physically not present and would not be initialized. It is not advisable to change the Front panel port count when some configurations are already saved. Once the Front panel port count is configured, the switch has to be restarted before saving any configuration. Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissAuditLogStatus | 1.3.6.1.4.1.2076.81.1.48 | INTEGER | RW | enable(1) | |||||||||||||||||
scalar · INTEGER · read-write · current To Enable or disable Audit Logging
Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissAuditLogFileName | 1.3.6.1.4.1.2076.81.1.49 | DisplayString (SIZE (1..128)) | RW | /backup/config.txt | |||||||||||||||||
scalar · DisplayString (SIZE (1..128)) · read-write · current The name of the file to which Audit log is saved Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissAuditLogFileSize | 1.3.6.1.4.1.2076.81.1.50 | Unsigned32 (1024..1048576) | RW | 1048576 | |||||||||||||||||
scalar · Unsigned32 (1024..1048576) · read-write · current This is the maximum file size in bytes of the config.txt file Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissAuditLogReset | 1.3.6.1.4.1.2076.81.1.51 | TruthValue | RW | 2 | |||||||||||||||||
scalar · TruthValue · read-write · current Setting this to true ,erases the contents in configs.txt fileand start logging Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissAuditLogRemoteIpAddr | 1.3.6.1.4.1.2076.81.1.52 | IpAddress | RW | deprecated | 0.0.0.0 | ||||||||||||||||
scalar · IpAddress · read-write · deprecated IP Address of the remote system to which the Audit file has to be transfered from flash. This object is deprecated, as this object supports only IPv4, this IP can be set through issAuditLogRemoteIpvxAddr object and object issAuditLogRemoteAddrType will be set to 1 i.e. IPv4 Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissAuditLogInitiateTransfer | 1.3.6.1.4.1.2076.81.1.53 | TruthValue | RW | 2 | |||||||||||||||||
scalar · TruthValue · read-write · current Setting this will start transfer of the file indicated by issAuditLogFileName from flash to remote Address mentioned by issAuditLogRemoteIpAddr Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissAuditTransferFileName | 1.3.6.1.4.1.2076.81.1.54 | DisplayString (SIZE (0..128)) | RW | | |||||||||||||||||
scalar · DisplayString (SIZE (0..128)) · read-write · current The name of the file to be retrieved from flash Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissDownLoadTransferMode | 1.3.6.1.4.1.2076.81.1.55 | INTEGER | RW | tftp(1) | |||||||||||||||||
scalar · INTEGER · read-write · current To select the Transfer mode for downloading image.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissDownLoadUserName | 1.3.6.1.4.1.2076.81.1.56 | DisplayString (SIZE (0..20)) | RW | | |||||||||||||||||
scalar · DisplayString (SIZE (0..20)) · read-write · current This mib-object is used for setting User name required for downloading image. When Transfer Mode is selected as tftp, contents of this mib-object becomes irrelevant. Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissDownLoadPassword | 1.3.6.1.4.1.2076.81.1.57 | DisplayString (SIZE (0..20)) | RW | | |||||||||||||||||
scalar · DisplayString (SIZE (0..20)) · read-write · current This mib-object is used for setting password required for downloading image. When Transfer Mode is selected as tftp, contents of this mib-object becomes irrelevant. Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissUploadLogTransferMode | 1.3.6.1.4.1.2076.81.1.58 | INTEGER | RW | tftp(1) | |||||||||||||||||
scalar · INTEGER · read-write · current To select the Transfer mode for uploading log file.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissUploadLogUserName | 1.3.6.1.4.1.2076.81.1.59 | DisplayString (SIZE (0..20)) | RW | | |||||||||||||||||
scalar · DisplayString (SIZE (0..20)) · read-write · current This mib-object is used for setting User name required for uploading log file. When Transfer Mode is selected as tftp, contents of this mib-object becomes irrelevant. Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissUploadLogPasswd | 1.3.6.1.4.1.2076.81.1.60 | DisplayString (SIZE (0..20)) | RW | | |||||||||||||||||
scalar · DisplayString (SIZE (0..20)) · read-write · current This mib-object is used for setting password required for uploading log file. When Transfer Mode is selected as tftp, contents of this mib-object becomes irrelevant. Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissConfigSaveTransferMode | 1.3.6.1.4.1.2076.81.1.61 | INTEGER | RW | tftp(1) | |||||||||||||||||
scalar · INTEGER · read-write · current To select the Transfer mode for uploading/downloading configurations to/from a remote system. Contents of this mib is relevant only when issConfigSaveOption is remote save.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissConfigSaveUserName | 1.3.6.1.4.1.2076.81.1.62 | DisplayString (SIZE (0..20)) | RW | | |||||||||||||||||
scalar · DisplayString (SIZE (0..20)) · read-write · current This mib-object is used for setting User name required for uploading/downloading the configurations to/from a remote site. Contents of this mib is relevant only when issConfigSaveOption is remote save and issConfigSaveTransferMode is SFTP. Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissConfigSavePassword | 1.3.6.1.4.1.2076.81.1.63 | DisplayString (SIZE (0..20)) | RW | | |||||||||||||||||
scalar · DisplayString (SIZE (0..20)) · read-write · current This mib-object is used for setting Password required for uploading/downloading the configurations to/from a remote site. Contents of this mib is relevant only when the value of issConfigSaveOption is remote save and issConfigSaveTransferMode is SFTP. Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissSwitchMinThresholdTemperature | 1.3.6.1.4.1.2076.81.1.64 | Integer32 (-35..30) | RW | 10 | |||||||||||||||||
scalar · Integer32 (-35..30) · read-write · current Indicates the minimum threshold temperature of the switch in celsius. When the current temperature drops below the threshold, an SNMP trap with maximum severity will be sent to the manager. Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissSwitchMaxThresholdTemperature | 1.3.6.1.4.1.2076.81.1.65 | Integer32 (35..90) | RW | 40 | |||||||||||||||||
scalar · Integer32 (35..90) · read-write · current Indicates the maximum threshold temperature of the switch in celsius. When the current temperature rises above the threshold, an SNMP trap with maximum severity will be sent to the manager. Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissSwitchCurrentTemperature | 1.3.6.1.4.1.2076.81.1.66 | Integer32 | RO | 43 | |||||||||||||||||
scalar · Integer32 · read-only · current Indicates the current temperature of the switch in celsius. Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissSwitchMaxCPUThreshold | 1.3.6.1.4.1.2076.81.1.67 | Integer32 (1..100) | RW | 100 | |||||||||||||||||
scalar · Integer32 (1..100) · read-write · current Indicates the maximum CPU usage of the switch in percentage. When CPU load exceeds the threshold value, an SNMP trap with maximum severity will be sent to the manager. Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissSwitchCurrentCPUThreshold | 1.3.6.1.4.1.2076.81.1.68 | Integer32 | RO | 1 | |||||||||||||||||
scalar · Integer32 · read-only · current Indicates the current CPU threshold of the switch in percentage Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissSwitchPowerSurge | 1.3.6.1.4.1.2076.81.1.69 | Integer32 (1..255) | RW | 230 | |||||||||||||||||
scalar · Integer32 (1..255) · read-write · current Indicates the maximum power supply of the switch in volts. When the current voltage exceeds the threshold value, an SNMP trap with maximum severity will be sent to the manager. Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissSwitchPowerFailure | 1.3.6.1.4.1.2076.81.1.70 | Integer32 (1..255) | RW | 100 | |||||||||||||||||
scalar · Integer32 (1..255) · read-write · current Indicates the minimum power supply of the switch in volts. When the current voltage drops below the threshold value, an SNMP trap with maximum severity will be sent to the manager. Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissSwitchCurrentPowerSupply | 1.3.6.1.4.1.2076.81.1.71 | Integer32 | RO | 230 | |||||||||||||||||
scalar · Integer32 · read-only · current Indicates the current power supply in volts. Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissSwitchMaxRAMUsage | 1.3.6.1.4.1.2076.81.1.72 | Integer32 (1..100) | RW | 100 | |||||||||||||||||
scalar · Integer32 (1..100) · read-write · current Indicates the maximum RAM usage of the switch in percentage. When the RAM usage crosses the threshold percentage an SNMP trap with maximum severity will be sent to the manager. Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissSwitchCurrentRAMUsage | 1.3.6.1.4.1.2076.81.1.73 | Integer32 | RO | 58 | |||||||||||||||||
scalar · Integer32 · read-only · current Indicates the current RAM usage of the switch in percentage Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissSwitchMaxFlashUsage | 1.3.6.1.4.1.2076.81.1.74 | Integer32 (1..100) | RW | 100 | |||||||||||||||||
scalar · Integer32 (1..100) · read-write · current Indicates the maximum flash usage of the switch in percentage. When the flash usage crosses the threshold percentage an SNMP trap with maximum severity will be sent to the manager. Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissSwitchCurrentFlashUsage | 1.3.6.1.4.1.2076.81.1.75 | Integer32 | RO | 83 | |||||||||||||||||
scalar · Integer32 · read-only · current Indicates the current flash usage of the switch in percentage Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissConfigRestoreFileFormatVersion | 1.3.6.1.4.1.2076.81.1.76 | DisplayString (SIZE (1..12)) | RO | 1.1 | |||||||||||||||||
scalar · DisplayString (SIZE (1..12)) · read-only · current Config Save Restoration file format Version.This issConfigRestoreFile FormatVersion value will be compared in each reboot against file format version value stored in restoration file.Restoration will occur only if the Restore file format version OID in restoration file matches this OID and the value of Restore file format version field in restoration file matches this OID's value. The current value of this issConfigRestoreFileFormatVersion is 1.1. If any change happens in Restore File Format,then the value of this object will be updated like this 1.2,1.3,1.4,1.5,.... Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissDebugOption | 1.3.6.1.4.1.2076.81.1.77 | DisplayString (SIZE (0..288)) | RW | | |||||||||||||||||
scalar · DisplayString (SIZE (0..288)) · read-write · current This object stores the trace option string input given by the user. To enable particular trace the user has to enter the corresponding string(given below) assigned for that. And for enabling more than once traces the user has to enter the corresponding strings with SPACE delimiter between each string. enable - Enables the corresponding option. disable - Disables the corresponding option. init-shut - Init and Shutdown traces failure - All Failure Traces func-entry-exit - Funtion entry and exit for example to enable init-shut and failure trace the input string should be enable init-shut failure Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissConfigDefaultValueSaveOption | 1.3.6.1.4.1.2076.81.1.78 | INTEGER | RW | disabled(2) | |||||||||||||||||
scalar · INTEGER · read-write · current Indicates whether default values needs to be saved or not when incremental save option is true.'enabled' value implies, MSR stores default values also when Incremental save is true.'disabled' value implies, MSR does not store default values when Incremental save is true. Configuring this object value will update in issnvram.txt file. The configured value will get into effect only after rebooting the ISS.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissConfigSaveIpAddrType | 1.3.6.1.4.1.2076.81.1.79 | InetAddressType | RW | 1 | |||||||||||||||||
scalar · InetAddressType · read-write · current This object specifies the address type of the remote system to which the switch configurations have to be saved.The address type can be IPv4 or IPv6 unicast address or DNS. This object is valid only if 'issConfigSaveOption' is chosen to be 'remoteSave'. Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissConfigSaveIpvxAddr | 1.3.6.1.4.1.2076.81.1.80 | InetAddress | RW | | |||||||||||||||||
scalar · InetAddress · read-write · current This object specifies the IP Address of the remote system to which the switch configurations have to be saved. It supports DNS host name when 'issConfigSaveIpAddrType' is of DNS Type. This object is valid only if 'issConfigSaveOption' is chosen to be 'remoteSave'. Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissConfigRestoreIpAddrType | 1.3.6.1.4.1.2076.81.1.81 | InetAddressType | RW | 1 | |||||||||||||||||
scalar · InetAddressType · read-write · current This object specifies the IP Address type of the remote system from where the switch configurations have to be downloaded to the 'Startup Configuration File' in the flash. The address type can be IPv4 or IPv6 unicast address or DNS. Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissConfigRestoreIpvxAddr | 1.3.6.1.4.1.2076.81.1.82 | InetAddress | RW | 0a:00:00:02 | |||||||||||||||||
scalar · InetAddress · read-write · current This object specifies the IP Address of the remote system from where the switch configurations have to be downloaded to the 'Startup Configuration File' in the flash. The address type can be IPv4 or IPv6 unicast address or DNS type. Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissDlImageFromIpAddrType | 1.3.6.1.4.1.2076.81.1.83 | InetAddressType | RW | 1 | |||||||||||||||||
scalar · InetAddressType · read-write · current This object specifies the address type of machine from where the image has to be downloaded. The address type can be IPv4 or IPv6 unicast address or DNS. Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissDlImageFromIpvx | 1.3.6.1.4.1.2076.81.1.84 | InetAddress | RW | | |||||||||||||||||
scalar · InetAddress · read-write · current The IP Address of machine from where the image has to be downloaded. Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissUploadLogFileToIpAddrType | 1.3.6.1.4.1.2076.81.1.85 | InetAddressType | RW | 1 | |||||||||||||||||
scalar · InetAddressType · read-write · current This object specifies the address Type of machine to which the log file is to be uploaded.The address type can be IPv4 or IPv6 unicast address or DNS. Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissUploadLogFileToIpvx | 1.3.6.1.4.1.2076.81.1.86 | InetAddress | RW | | |||||||||||||||||
scalar · InetAddress · read-write · current This object specifies the address type of machine to which the log file is to be uploaded. Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissAuditLogRemoteIpAddrType | 1.3.6.1.4.1.2076.81.1.87 | InetAddressType | RW | 0 | |||||||||||||||||
scalar · InetAddressType · read-write · current IP Address Type of the remote system to which the Audit file has to be transfered from flash. Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissAuditLogRemoteIpvxAddr | 1.3.6.1.4.1.2076.81.1.88 | InetAddress | RW | | |||||||||||||||||
scalar · InetAddress · read-write · current IP Address of the remote system to which the Audit file has to be transfered from flash. Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissSystemTimerSpeed | 1.3.6.1.4.1.2076.81.1.89 | Unsigned32 (1..1000) | RW | 1 | |||||||||||||||||
scalar · Unsigned32 (1..1000) · read-write · current Configures the system timer speed. This is for testing purpose. Value - 1 enables the timer to run in real time speed. Values from (2 - 1000), enables the timer to run (2x - 1000x) faster. Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissMgmtInterfaceRouting | 1.3.6.1.4.1.2076.81.1.90 | INTEGER | RW | disabled(2) | |||||||||||||||||
scalar · INTEGER · read-write · current Enables / Disables Routing over the Management Interface. This object can be configured only if the Management Port is used for IP Access.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissMacLearnRateLimit | 1.3.6.1.4.1.2076.81.1.91 | Integer32 (0..2147483647) | RW | 1000 | |||||||||||||||||
scalar · Integer32 (0..2147483647) · read-write · current Maximum number of unicast dynamic MAC (L2) entries hardware can learn in the system, in a configured time interval 'issMacLearnRateLimitInterval'. In next subsequent time interval, hardware can learn number of previously learnt MAC entries plus present 'issMacLearnRateLimit' value, this cycle will continue until MAC learning reaches to maximum number of L2 unicast dynamic entries learning capacity of the system. If rate limit is changed while 'issMacLearnLimitRateInterval' timer is running, new rate limit value takes effect on next timer restart. This limit is to control the number of MAC entries indication to control plane from hardware, when hardware MAC learning is enabled. Configuration value '0' disables this feature in the system. This configuration does not impose any restrictions on multicast/broadcast and dynamic/static/protocol(MMRP) MAC learning capability limits. Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissMacLearnRateLimitInterval | 1.3.6.1.4.1.2076.81.1.92 | Unsigned32 (1..100000) | RW | 1000 | |||||||||||||||||
scalar · Unsigned32 (1..100000) · read-write · current Number of MAC entries,'issMacLearnRateLimit' that can be learnt in the system in this configured time interval. Any changed timer interval value will take effect in next timer restart.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissVrfUnqMacFlag | 1.3.6.1.4.1.2076.81.1.93 | INTEGER | RW | disable(0) | |||||||||||||||||
scalar · INTEGER · read-write · current Unique mac address can be assigned to each virtual router by enabling this flag. Configuring this object value will result in updation to issnvram.file. The configured value will take effect in ISS on next reboot.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissLoginAttempts | 1.3.6.1.4.1.2076.81.1.94 | Integer32 (1..10) | RW | 3 | |||||||||||||||||
scalar · Integer32 (1..10) · read-write · current Number of times a user may be allowed to login using wrong password in the login prompt. Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissLoginLockTime | 1.3.6.1.4.1.2076.81.1.95 | Integer32 (30..600) | RW | 30 | |||||||||||||||||
scalar · Integer32 (30..600) · read-write · current Time in seconds a user is blocked following unsuccessful logins. Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissAuditLogSizeThreshold | 1.3.6.1.4.1.2076.81.1.96 | Unsigned32 (1..99) | RW | 70 | |||||||||||||||||
scalar · Unsigned32 (1..99) · read-write · current This is the threshold value of the Log storage space with respect to the maximum Log Storage Space. It is entered as a percentage value. Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissTelnetStatus | 1.3.6.1.4.1.2076.81.1.97 | INTEGER | RW | enable(1) | |||||||||||||||||
scalar · INTEGER · read-write · current This object is for enabling or disabling the TELNET in the system. Set operation of enable will move this object to the enableInProgress first then to the enable on successfull transition. Otherwise it will move back to the old state. Same applies to the disable also. CAUTION: enableInProgress and disableInProgress are not admin configurable values
Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissWebSessionTimeOut | 1.3.6.1.4.1.2076.81.1.98 | Integer32 (1..300) | RW | 300 | |||||||||||||||||
scalar · Integer32 (1..300) · read-write · current Set the Web Session Time Out Value in Seconds Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissWebSessionMaxUsers | 1.3.6.1.4.1.2076.81.1.99 | Integer32 | RW | 10 | |||||||||||||||||
scalar · Integer32 · read-write · current Set the maximum number of web sessions Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissHeartBeatMode | 1.3.6.1.4.1.2076.81.1.100 | INTEGER | RW | internal(1) | |||||||||||||||||
scalar · INTEGER · read-write · current The object is for setting the method for Redundancy manager election mechanism, it can be internal election logic or it can be a external logic. When this object is set to be internal, proprietary election logic called as HearBeat mechanism is applied for electing the Active/Standby card in a redundant systems. When this object is set to be external, external election logic should be applied for electing Active/Standby card in a redundant systems. By default this object is set to Internal.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissRmRType | 1.3.6.1.4.1.2076.81.1.101 | INTEGER | RW | hot(1) | |||||||||||||||||
scalar · INTEGER · read-write · current The object is for setting the type of the Redundancy manager, it can be Hot or Cold. When this object is set to be cold, whenever there is node state transition from Standby to Active, the node needs to re-start, re-initialized the hardware completely. When this object is set to be Hot, whenever there is node state transition from Standby to Active, the hardware should not be re-initialized. When the configurations are saved in a file in Active node, then this needs to be transferred to the standby node in both the redundancy modes. By default this is set to Hot.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissRmDType | 1.3.6.1.4.1.2076.81.1.102 | INTEGER | RW | shared(1) | |||||||||||||||||
scalar · INTEGER · read-write · current This object specifies the type of the dataplane/hardware, it can be a shared dataplane or a separate dataplane. When this object is set to be shared, standby card in a redundancy system should not program the hardware and hardware audit should be conducted to sync the hardware and software after switchover/node-transition. When this object is set to be separate, it specifies that the nodes have separate hardware, therefore standby card in a redundant system should program the hardware and hardware audit is not required, since the hardware and software are in sync always. By default this is set to Shared.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissClearConfig | 1.3.6.1.4.1.2076.81.1.103 | TruthValue | RW | 2 | |||||||||||||||||
scalar · TruthValue · read-write · current When the object is set to TRUE, configurations will be cleared and default configurations will be restored. The value will be reset to FALSE again. Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissClearConfigFileName | 1.3.6.1.4.1.2076.81.1.104 | DisplayString (SIZE (1..128)) | RW | | |||||||||||||||||
scalar · DisplayString (SIZE (1..128)) · read-write · current This is the name of the file, which contains the default configurations to be restored once configurations are cleared. This is optional. When this file name is given, configurations in this file are assumed to be default configurations. This configuration will be restored once the configurations are cleared in ISS data base. When this file name is not given, default configurations will not be restored. Only default interface and VLAN will be brought up for management connectivity. When default configurations are to be restored, this object should be configured first before configuring the issClearConfig object. Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissTelnetClientStatus | 1.3.6.1.4.1.2076.81.1.105 | INTEGER | RW | enabled(1) | |||||||||||||||||
scalar · INTEGER · read-write · current This object is for enabling or disabling the TELNET client functionality in the system. Set operation of enable will allow to establish new Telnet client sessions. Set operation of disable will not allow a new Telnet client session, also terminates the active client sessions which are already running. By default it will be enabled
Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissSshClientStatus | 1.3.6.1.4.1.2076.81.1.106 | INTEGER | RW | enabled(1) | |||||||||||||||||
scalar · INTEGER · read-write · current This object is for enabling or disabling the SSH client functionality in the system. Set operation of enable will allow to establish new SSH client sessions. Set operation of disable will not allow a new SSH client sessions, also terminates the active client sessions which are already running. By default it will be enabled
Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissActiveTelnetClientSessions | 1.3.6.1.4.1.2076.81.1.107 | Integer32 | RO | 0 | |||||||||||||||||
scalar · Integer32 · read-only · current Specifies the number of active Telnet client sessions running Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissActiveSshClientSessions | 1.3.6.1.4.1.2076.81.1.108 | Integer32 | RO | 0 | |||||||||||||||||
scalar · Integer32 · read-only · current Specifies the number of active SSH client sessions running Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissLogFileSize | 1.3.6.1.4.1.2076.81.1.109 | Unsigned32 | RW | 1048576 | |||||||||||||||||
scalar · Unsigned32 · read-write · current This is the maximum file size in bytes of the log file Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissLogReset | 1.3.6.1.4.1.2076.81.1.110 | TruthValue | RW | 2 | |||||||||||||||||
scalar · TruthValue · read-write · current Setting this to true ,erases the contents in configs.txt fileand start logging Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissLogSizeThreshold | 1.3.6.1.4.1.2076.81.1.111 | Unsigned32 (1..99) | RW | 70 | |||||||||||||||||
scalar · Unsigned32 (1..99) · read-write · current This is the threshold value of the Log storage space with respect to the maximum Log Storage Space. It is entered as a percentage value. Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissAutomaticPortCreate | 1.3.6.1.4.1.2076.81.1.112 | INTEGER | RW | disabled(2) | |||||||||||||||||
scalar · INTEGER · read-write · current This object is for enabling and disabling automatic port create feature.When set to enabled the ports in will be automatically created in RSTP module when it is mapped to a context.When set to disabled ports are not created automatically and ports can be created at rstp module level.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissUlRemoteLogFileName | 1.3.6.1.4.1.2076.81.1.113 | DisplayString (SIZE (1..128)) | RW | iss.log | |||||||||||||||||
scalar · DisplayString (SIZE (1..128)) · read-write · current This object is used to specify the filename/filename with path to which the local file need to be copied in the remote system. This object is useful only when the 'LogOption' is chosen as 'file'. Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissDefaultExecTimeOut | 1.3.6.1.4.1.2076.81.1.114 | Unsigned32 | RW | 300 | |||||||||||||||||
scalar · Unsigned32 · read-write · current This object is for configuring the default idle time out for ISS Prompt (exec-time out). Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissRmStackingInterfaceType | 1.3.6.1.4.1.2076.81.1.115 | INTEGER | RW | inband(2) | |||||||||||||||||
scalar · INTEGER · read-write · current This object is used to specify the type of stacking Interface used for RM communication . Interface can be either an Out of Band port (or) an Inband Ethernet port. This will be specified in issnvram.txt. If an Out of Band port is used,RM Interface should be specified in issnvram.txt . RM Heartbeat and synchronization messages will be transmitted as IP packets. Native Linux TCP/IP stack is used to achieve Transport protocol functionality. If an Inband Ethernet port is used, RM Stack Interface will be specified in Nodeid file . RM Heartbeat messages will be transmitted as Ethernet packets and synchronization messages will be transmitted as IP packets .Aricent TCP/IP stack is used to achieve Transport protocol functionality.IP Address and the subnet Mask to be used for this TCP/IP communication will be specified in NodeId file. Configuring this object will result in updation to issnvram.txt file. The configured value will take effect in ISS on next reboot.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissPeerLoggingOption | 1.3.6.1.4.1.2076.81.1.116 | INTEGER | RW | console(1) | |||||||||||||||||
scalar · INTEGER · read-write · current The Logging option specifying whether the Standby logging is to be done at console or to a file(system buffer) in the system. Flash specifies the logging of traces into a file.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissStandbyRestart | 1.3.6.1.4.1.2076.81.1.117 | TruthValue | RW | 2 | |||||||||||||||||
scalar · TruthValue · read-write · current In a High Availability System, this object allows the user to restart the Standby switch (i.e) the entire Standby switch will operationally go down and start again. Setting a value of 'true' causes the Standby switch to be restarted. This configuration will be done in the Active switch in order to restart the Standby switch. This configuration will not have any impact on the Active switch. Active switch can be restarted using issRestart object. Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissRestoreType | 1.3.6.1.4.1.2076.81.1.118 | INTEGER | RW | msr(1) | |||||||||||||||||
scalar · INTEGER · read-write · current Specifies whether the restoration type is MIB based save and restore or CLI based save and restore. The value 'msr' specifies that the configuration restore will be in the format of MIB OID. The value 'csr' specifies that the configuration restore will be in the format of CLI commands
Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissSwitchModeType | 1.3.6.1.4.1.2076.81.1.119 | INTEGER | RW | ||||||||||||||||||
scalar · INTEGER · read-write · current Configures the switching mode and determines when the switch begins forwarding the frame. The configuration is applicable to all packets being switched or routed through the switch. When configured as store-forward, the switch stores each frame until the entire frame has been received and checked for cyclic redundancy check (CRC) errors before forwarding them to the network. When configured as cut-through, the switch starts forwarding the frame even before receiving the entire frame as soon as the destination details are read from the packet header The switching speed will be slower in store-forward when compared to cut-through mode
| |||||||||||||||||||||
| SissHardwareSerialNumber | 1.3.6.1.4.1.2076.81.1.120 | DisplayString (SIZE (1..15)) | RO | ES9E003484 | |||||||||||||||||
scalar · DisplayString (SIZE (1..15)) · read-only · current Serial number of the Hardware. Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissDlImageType | 1.3.6.1.4.1.2076.81.1.121 | INTEGER | RW | ||||||||||||||||||
scalar · INTEGER · read-write · current To select the type of image to be downloaded.
| |||||||||||||||||||||
| NissConfigControl | 1.3.6.1.4.1.2076.81.2 | ||||||||||||||||||||
| TissConfigCtrlTable | 1.3.6.1.4.1.2076.81.2.1 | NA | |||||||||||||||||||
table · not-accessible · current A table to control device features like egress traffic control, stats collection, etc. either for the entire switch or for each interface in the switch. | |||||||||||||||||||||
| RissConfigCtrlEntry | 1.3.6.1.4.1.2076.81.2.1.1 | NA | |||||||||||||||||||
row · not-accessible · current An entry appears in this table for each interface in the system. In addition to that an entry with index '0' is created in this table by default. If 'issConfigCtrlStatus' of the entry '0' is made 'valid', then global control is chosen and the values against entry '0' is applicable for all the interfaces of the switch. If 'issConfigCtrlStatus' of the entry '0' is made 'invalid', then interface-wise control is chosen & the values against each interface index is applicable for that interface. At a particular point of time, either global control will be applicable or interface-wise control is applicable. Both will not be considered together. Index to the table is the interface index of the port.
| |||||||||||||||||||||
| CissConfigCtrlIndex | 1.3.6.1.4.1.2076.81.2.1.1.1 | Integer32 (0..65535) | NA | ||||||||||||||||||
column · Integer32 (0..65535) · not-accessible · current Interface index of the port for which the configuration in this entry applies. If any configuration is made in this table for the index '0', that configuration will be considered as global configuration and is applicable for all the interfaces of the switch. | |||||||||||||||||||||
| CissConfigCtrlEgressStatus | 1.3.6.1.4.1.2076.81.2.1.1.2 | INTEGER | RW | enabled(1) | |||||||||||||||||
column · INTEGER · read-write · current Controls the transmission of egress traffic over this interface. This value for entry '0' controls the egress traffic over all interfaces.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CissConfigCtrlStatsCollection | 1.3.6.1.4.1.2076.81.2.1.1.3 | INTEGER | RW | enabled(1) | |||||||||||||||||
column · INTEGER · read-write · current Enables or disables statistics collection for this interface. This value for entry '0' controls the stats collection for all interfaces.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CissConfigCtrlStatus | 1.3.6.1.4.1.2076.81.2.1.1.4 | INTEGER | RW | valid(1) | |||||||||||||||||
column · INTEGER · read-write · current Speficies the validity of the entry. If the 'Config Control Status' for entry '0' is made 'valid', then global control is chosen in the system. It signifies that the values against entry '0' is applicable for all the interfaces of the switch. If the 'Config Control Status' for entry '0' is made 'invalid', then interface-wise control is chosen. Then the values against each interface index is applicable for that interface. By default, 'issConfigCtrlStatus' will be 'invalid' for entry '0' and 'valid' for all other entries. (ie) by default, interface-wise configuration is enabled in the system. The status of entries other than the zeroth(0th) entry can not be made 'invalid'.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| TissPortCtrlTable | 1.3.6.1.4.1.2076.81.2.2 | NA | |||||||||||||||||||
table · not-accessible · current A table to control the port specific parameters of the device like speed, duplex mode, etc. | |||||||||||||||||||||
| RissPortCtrlEntry | 1.3.6.1.4.1.2076.81.2.2.1 | NA | |||||||||||||||||||
row · not-accessible · current An entry appears in this table for each interface in the system. Index to the table is the interface index of the port.
| |||||||||||||||||||||
| CissPortCtrlIndex | 1.3.6.1.4.1.2076.81.2.2.1.1 | Integer32 (1..65535) | NA | ||||||||||||||||||
column · Integer32 (1..65535) · not-accessible · current Interface index of the port for which the configuration in this entry applies. | |||||||||||||||||||||
| CissPortCtrlMode | 1.3.6.1.4.1.2076.81.2.2.1.2 | INTEGER | RW | auto(1) | |||||||||||||||||
column · INTEGER · read-write · current Speficies the mode in which the speed, duplex modes and flow control of the interface is determined. If set as 'auto', the hardware senses speed and negotiates with the port on the other end of the link for data transfer operation as 'full-duplex' or 'half-duplex' and about flow contol. If set as 'nonegotiation', the configured values for interface speed, duplex mode and flow control will be effective.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CissPortCtrlDuplex | 1.3.6.1.4.1.2076.81.2.2.1.3 | INTEGER | RW | full(1) | |||||||||||||||||
column · INTEGER · read-write · current Configures interface data transfer mode as full-duplex or half-duplex. This object can be configured only if the 'PortCtrlMode' is 'nonegotiation'. If the 'PortCtrlMode' is 'auto', it obtains the value from Hardware after negotiating with its peer
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CissPortCtrlSpeed | 1.3.6.1.4.1.2076.81.2.2.1.4 | INTEGER | RW | hundredMBPS(2) | |||||||||||||||||
column · INTEGER · read-write · current Configures interface speed. This object can be configured only if the 'PortCtrlMode' is 'nonegotiation'. If the 'PortCtrlMode' is 'auto', it obtains the value from Hardware after negotiating with its peer
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CissPortCtrlFlowControl | 1.3.6.1.4.1.2076.81.2.2.1.5 | INTEGER | RW | deprecated | disable(2) | ||||||||||||||||
column · INTEGER · read-write · deprecated Enables / disables flow control for the interface. This object be configured only if the 'PortCtrlMode' is 'nonegotiation'. If the 'PortCtrlMode' is 'auto', it obtains the value from Hardware after negotiating with its peer. Since this object is deprecated, corresponding functionality can be realised by dot3PauseAdminMode from stdether.mib
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CissPortCtrlRenegotiate | 1.3.6.1.4.1.2076.81.2.2.1.6 | TruthValue | RW | 2 | |||||||||||||||||
column · TruthValue · read-write · current When configured as 'true', restarts autonegotiation on the interface. Once autonegotiation is restarted, the value of this object reverts to 'false'. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CissPortCtrlMaxMacAddr | 1.3.6.1.4.1.2076.81.2.2.1.7 | Integer32 | RW | 100 | |||||||||||||||||
column · Integer32 · read-write · current Specifies the maximum number of new MAC addresses that can be learnt over the interface. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CissPortCtrlMaxMacAction | 1.3.6.1.4.1.2076.81.2.2.1.8 | INTEGER | RW | drop(1) | |||||||||||||||||
column · INTEGER · read-write · current Specifies the action to be taken when the maximum number of new MAC addresses that can be learnt over the interface is exceeded. If the action is 'drop', the packet with new mac address will be dropped once the maximum number of new MAC addresses that can be learnt over the interface is exceeded. If the action is 'purgeLRU', the 'Least Recently Used' mac address will be deleted from the MAC table and the new mac address will be added.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CissPortHOLBlockPrevention | 1.3.6.1.4.1.2076.81.2.2.1.9 | INTEGER | RW | enabled(2) | |||||||||||||||||
column · INTEGER · read-write · current Enables or disables Head-Of-Line Blocking prevention on a port.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CissPortAutoNegAdvtCapBits | 1.3.6.1.4.1.2076.81.2.2.1.10 | OCTET STRING | RW | 10:24:00:00 | |||||||||||||||||
column · OCTET STRING · read-write · current A value uniquely identifies the set of capabilities advertised by the local auto negotiation entity other than the standard capabilities supported by ifMauAutoNegCapAdvertisedBits. When this object is needed to be configured, one of the capabilities from the standard object should be set to bOther. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CissPortCpuControlledLearning | 1.3.6.1.4.1.2076.81.2.2.1.11 | INTEGER | RW | 0 | |||||||||||||||||
column · INTEGER · read-write · current Enables or disables the CPU controlled learning on a port. The default behavior is hardware learning. By enabling this object software learning on that particular port is enabled. When CPU controlled learning is enabled, for the first time, packet will be copied to CPU and source MAC address learning will not happen in the hardware. When packet is received at PNAC - if the source MAC address is authorized, the packet will be allowed to go through further processing. Else, the packet will be dropped. When packets from authorized MAC address are received at VLAN, MAC learning will happen at VLAN and the same entry will be programmed in the hardware. Once the MAC address is learnt, further forwarding will happen at driver itself. The Mac address entries which are added through software learning are checked in periodical intervals for the HIT entry. If there is no traffic for that entry, the HIT flag won't be set. The entry will be removed from the hardware if the hit flag is not set. Note: When software learning is enabled, rate limiting to the port needs to be configured
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CissPortMdiOrMdixCap | 1.3.6.1.4.1.2076.81.2.2.1.12 | INTEGER | RW | auto(1) | |||||||||||||||||
column · INTEGER · read-write · current Specifies the port should be in Auto-Mdix mode or Mdi/Mdix. Setting the value to `auto` enables the Auto MDIX in the port - issPortCtrlIndex. This will be effective only when the speed of the particular port is auto negotiable. Setting the value to `mdi` disables the Auto MDIX in the port and the port will be in mdi mode. Setting the value to `mdix` disables the Auto MDIX in the port and the port will be in mdix mode.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CissPortCtrlFlowControlMaxRate | 1.3.6.1.4.1.2076.81.2.2.1.13 | Integer32 (0..80000000) | RW | 0 | |||||||||||||||||
column · Integer32 (0..80000000) · read-write · current Configures the maximum rate (kbps) - a high water mark beyond which pause frames will be generated to flow control the ingress traffic. This value should be set to 0 if no pause frame generation is required. In chipsets that does not support seperate rate configuration for pause frame generation, this object's value will take effect on the interface ingress speed. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CissPortCtrlFlowControlMinRate | 1.3.6.1.4.1.2076.81.2.2.1.14 | Integer32 (0..80000000) | RW | 0 | |||||||||||||||||
column · Integer32 (0..80000000) · read-write · current Configures the minimum rate (kbps) - a low water mark below which pause frames generation will be stopped. This value should be set to a value lesser that of 'issPortCtrlFlowControlMaxRate'. This value should be set to zero only when flow control is disabled. Chipsets on which this low water mark is not supported, the 'issPortCtrlFlowControlMaxRate' will alone be used. Example values from LibreNMS test devices
| |||||||||||||||||||||
| TissPortIsolationTable | 1.3.6.1.4.1.2076.81.2.3 | NA | |||||||||||||||||||
table · not-accessible · current This table is used to configure the port isolation feature. For a given port, user can configure the list of allowed forwarding/egress ports, where the packets for particular vlan that ingress the port can be forwarded. If the Vlan is not given, then the rule will be applied for all packets that ingress the given port. This table can be configured only for physical and link aggregated ports. Before a packet is sent out of a port (after all L2/L3 processing), port isolation table entry is referred for the ingress port of that packet. If an entry is present for that ingress port and if the outgoing port is configured as one of the egress ports , then the packet will be transmitted out of that outgoing port. Otherwise the packet will be dropped. If there is no entry configured for that ingress port in this table, then the packet will be transmitted on that outgoing port. | |||||||||||||||||||||
| RissPortIsolationEntry | 1.3.6.1.4.1.2076.81.2.3.1 | NA | |||||||||||||||||||
row · not-accessible · current Each etnry in this table gives a ingress port to egress port mapping. | |||||||||||||||||||||
| CissPortIsolationIngressPort | 1.3.6.1.4.1.2076.81.2.3.1.1 | InterfaceIndex | NA | ||||||||||||||||||
column · InterfaceIndex · not-accessible · current This object speficies the IfIndex of the ingress port. This port can be a physical or link aggregated port. | |||||||||||||||||||||
| CissPortIsolationInVlanId | 1.3.6.1.4.1.2076.81.2.3.1.2 | Integer32 (0..4094) | NA | ||||||||||||||||||
column · Integer32 (0..4094) · not-accessible · current If this object value is non-zero, then the port isolation rule is applied for all packets received on the given ingress port. Otherwise the rule is applied for this vlan packets received on the given ingress port. | |||||||||||||||||||||
| CissPortIsolationEgressPort | 1.3.6.1.4.1.2076.81.2.3.1.3 | InterfaceIndex | NA | ||||||||||||||||||
column · InterfaceIndex · not-accessible · current This object specifies one of the allowed egress ports for the given ingress port identified by the first index for this row. This port can be either a physical or link aggregated port. | |||||||||||||||||||||
| CissPortIsolationStorageType | 1.3.6.1.4.1.2076.81.2.3.1.4 | StorageType | RO | ||||||||||||||||||
column · StorageType · read-only · current Indicates the storage type of this entry.
Only 'volatile' and 'nonVolatile' values are allowed for this object.
'readOnly', 'permenant' and 'other' values are not allowed for this
object.
If this table is configured for an ingress port and InVlanId via
management, then the issPortIsolationStorageType for all the entries
with this ingress port as primary index and this InVlanId as
secondary index will have the values as 'nonVolatile'.
Otherwise it will be set to 'volatile'.
Entries in this table will be restored on reboot, only if the
corresponding issPortIsolationStorageType object is set as
nonVolatile. | |||||||||||||||||||||
| CissPortIsolationRowStatus | 1.3.6.1.4.1.2076.81.2.3.1.5 | RowStatus | RC | ||||||||||||||||||
column · RowStatus · read-create · current Denotes the Row Status for port isolation table entry.
Only 'CreateAndGo' and 'destroy' values are allowed for this
object. 'CreateAndWait' and 'notInService' values are not allowed.
Example:
To add ports 2, 3 as egress ports for ingress port 1 in this table,
the following sequence to be followed:
1. Set the issPortIsolationRowStatus as 'CreateAndGo' for the
entry with index
(issPortIsolationIngressPort = 1, issPortIsolationInVlanId =0,
issPortIsolationEgressPort = 2)
2. Set the issPortIsolationRowStatus as 'CreateAndGo' for the
entry with index
(issPortIsolationIngressPort = 1, issPortIsolationInVlanId =0,
issPortIsolationEgressPort = 3)
To add ports 5, 6 as egress ports for ingress port 7 and for vlan 5
in this table, the following sequence to be followed:
1. Set the issPortIsolationRowStatus as 'CreateAndGo' for the
entry with index
(issPortIsolationIngressPort = 7, issPortIsolationInVlanId =5,
issPortIsolationEgressPort = 5)
2. Set the issPortIsolationRowStatus as 'CreateAndGo' for the
entry with index
(issPortIsolationIngressPort = 7, issPortIsolationInVlanId =5,
issPortIsolationEgressPort = 6)
To delete a egress port 3 from the list of egress ports for ingress
port 1 do the following:
Set the issPortIsolationRowStatus as 'destroy' for the
entry with index
(issPortIsolationIngressPort = 1, issPortIsolationEgressPort = 3) | |||||||||||||||||||||
| NissMirror | 1.3.6.1.4.1.2076.81.3 | ||||||||||||||||||||
| SissMirrorStatus | 1.3.6.1.4.1.2076.81.3.1 | INTEGER | RW | enabled(2) | |||||||||||||||||
scalar · INTEGER · read-write · current This object is used to enable/disable mirroring feature in hardware. When set to 'disabled (1)', all mirroring configurations will be removed from hardware. When set to 'enabled (2)', all mirroring configurations present in software will be programmed in hardware.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissMirrorToPort | 1.3.6.1.4.1.2076.81.3.2 | Integer32 | RW | 0 | |||||||||||||||||
scalar · Integer32 · read-write · current Specifies the port to which the active mirrored traffic controlled by issMirrorCtrlTable is to be copied. Example values from LibreNMS test devices
| |||||||||||||||||||||
| TissMirrorCtrlTable | 1.3.6.1.4.1.2076.81.3.3 | NA | |||||||||||||||||||
table · not-accessible · current A table to control mirroring features for each interface in the switch. Parameters in this table are valid only when the 'issMirrorStatus' for the switch is not 'disabled'. | |||||||||||||||||||||
| RissMirrorCtrlEntry | 1.3.6.1.4.1.2076.81.3.3.1 | NA | |||||||||||||||||||
row · not-accessible · current An entry appears in this table for each interface in the system.
| |||||||||||||||||||||
| CissMirrorCtrlIndex | 1.3.6.1.4.1.2076.81.3.3.1.1 | Integer32 (1..65535) | NA | ||||||||||||||||||
column · Integer32 (1..65535) · not-accessible · current The interface index of the port for which the configuration in this entry applies. | |||||||||||||||||||||
| CissMirrorCtrlIngressMirroring | 1.3.6.1.4.1.2076.81.3.3.1.2 | INTEGER | RW | ||||||||||||||||||
column · INTEGER · read-write · current Provides control to enable or disable mirroring of ingress traffic over this interface to the mirrored-to port.
| |||||||||||||||||||||
| CissMirrorCtrlEgressMirroring | 1.3.6.1.4.1.2076.81.3.3.1.3 | INTEGER | RW | ||||||||||||||||||
column · INTEGER · read-write · current Provides control to enable or disable mirroring of egress traffic over this interface to the mirrored-to port.
| |||||||||||||||||||||
| CissMirrorCtrlStatus | 1.3.6.1.4.1.2076.81.3.3.1.4 | INTEGER | RW | ||||||||||||||||||
column · INTEGER · read-write · current Specifies the validity of the entry.
| |||||||||||||||||||||
| SissMirrorCtrlRemainingSrcRcrds | 1.3.6.1.4.1.2076.81.3.4 | Integer32 | RO | 100 | |||||||||||||||||
scalar · Integer32 · read-only · current Specifies the number of source records remaining in the system. Each record can store at least one source information. In case consecutive source id are configured then record will store the range Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissMirrorCtrlRemainingDestRcrds | 1.3.6.1.4.1.2076.81.3.5 | Integer32 | RO | 100 | |||||||||||||||||
scalar · Integer32 · read-only · current Specifies the number of destination records remaining in the system. Each record can store at least one destination information. In case consecutive destination id are configured then record will store the range Example values from LibreNMS test devices
| |||||||||||||||||||||
| TissMirrorCtrlExtnTable | 1.3.6.1.4.1.2076.81.3.6 | NA | |||||||||||||||||||
table · not-accessible · current This Table is used to configure advanced mirroring features like
- Port Based Mirroring:
- flow based mirroring
- vlan based mirroring
Following are the configuration details for Port based mirroring:
To configure source ports in a session
- issMirrorCtrlExtnMirrType - is set to portBased
- issMirrorCtrlExtnSrcTable - should be used to configure list
of source ports to be mirrored
in a session
- issMirrorCtrlExtnSrcId - represents the source port.
The port Id to be mirrored
should be given here.
- issMirrorCtrlExtnSrcCfg - this object is used to
add/remove a port in the
source port list
Example
To create a session 1 with source ports 5,6 following
sequence of configuration should be followed
For table issMirrorCtrlExtnTable
issMirrorCtrlExtnSessionIndex = 1 as index
issMirrorCtrlExtnMirrType = portBased
For table issMirrorCtrlExtnSrcTable
issMirrorCtrlExtnSessionIndex = 1 as index
issMirrorCtrlExtnSrcId = 5 as index
issMirrorCtrlExtnSrcCfg = add
issMirrorCtrlExtnSessionIndex = 1 as index
issMirrorCtrlExtnSrcId = 6 as index
issMirrorCtrlExtnSrcCfg = add
To configure destination ports in a session
- issMirrorCtrlExtnDestinationTable - should be used to
configure list of
destination ports to be
mirrored in a session
- issMirrorCtrlExtnDestination - represents the
destination port. The
port Id to which packets
should be mirrored should
be given here.
- issMirrorCtrlExtnDestCfg - this object is used to
add/remove a port in the
source port list.
Example
To create a session 1 with destination port 10,11 following
sequence of configuration should be followed
For table issMirrorCtrlExtnTable
issMirrorCtrlExtnSessionIndex = 1 as index
issMirrorCtrlExtnMirrType = portBased
For table issMirrorCtrlExtnDestinationTable
issMirrorCtrlExtnSessionIndex = 1 as index
issMirrorCtrlExtnDestination = 10 as index
issMirrorCtrlExtnDestCfg = add
issMirrorCtrlExtnSessionIndex = 1 as index
issMirrorCtrlExtnDestination = 11 as index
issMirrorCtrlExtnDestCfg = add
To Activate a session
- issMirrorCtrlExtnStatus - should be used to
activate/deactivate mirroring for a
session
Example
To enable mirroring for a session following sequence of
configuration should be followed
For table issMirrorCtrlExtnTable
issMirrorCtrlExtnSessionIndex = 1 as index
issMirrorCtrlExtnStatus = active
Above configurations applies to flow based mirroring also, the
issMirrorCtrlExtnSrcId used above for configuratin ports
should be used to configure flow Id
To enable remote monitoring of sources for a session
- issMirrorCtrlExtnRSpanStatus - should be used to
enable/disable remote
monitoring for a session
it can be used to set a
session as source rspan
session which implies source
entities for this session are
monitored remotely or can be
used to set a session
as destination rspan session
which implies that mirrored
data is received for this
session should be forwarded to
destination entities of this
session
- issMirrorCtrlExtnRSpanVlanId - it is the vlan id which is
reserved in the network to
carry Mirrored data,if the
session is configured as
source rspan session then data
mirrored for the source
entities will be forwarded on
this vlan if the session is
configured as destination
rspan session then data
received on this vlan will be
forwarded to the destination
entities of this session
Following are the configuration details for configurating Vlan
based mirroring:
To configure vlans as source for a session
- issMirrorCtrlExtnMirrType - is set to vlanBased
- issMirrorCtrlExtnSrcVlanTable - should be used to configure
list of source vlans to be
mirrored in a session
- issMirrorCtrlExtnSrcVlanId - represents a source vlan. The
vlan to be mirrored should be
given here.
- issMirrorCtrlExtnSrcVlanCfg - this object is used to
add/remove a vlan in the
source vlan list
Example
To create a session 1 with source list as vlan 5,6
belonging to context 1 following sequence of configuration
should be followed
For table issMirrorCtrlExtnTable
issMirrorCtrlExtnSessionIndex = 1 as index
issMirrorCtrlExtnMirrType = vlanBased
For table issMirrorCtrlExtnSrcVlanTable
issMirrorCtrlExtnSrcVlanContext = 1 as index
issMirrorCtrlExtnSessionIndex = 1 as index
issMirrorCtrlExtnSrcVlanId = 5 as index
issMirrorCtrlExtnSrcVlanCfg = add
issMirrorCtrlExtnSrcVlanContext = 1 as index
issMirrorCtrlExtnSessionIndex = 1 as index
issMirrorCtrlExtnSrcVlanId = 6 as index
issMirrorCtrlExtnSrcVlanCfg = add
Entries for this table can be configured only when issMirrorStatus
is set to enabled.
Configurations done through 'issMirrorCtrlTable' will change the
following for the first session on this table:
- Mirroring type will be changed to port-based
- Mode and Source entities will be overwritten
with the values configured through 'issMirrorCtrlTable'
- Destination entities will be overwritten
with the value configured through 'issMirrorToPort' object | |||||||||||||||||||||
| RissMirrorCtrlExtnEntry | 1.3.6.1.4.1.2076.81.3.6.1 | NA | |||||||||||||||||||
row · not-accessible · current An entry appears in this table for each session in the system. | |||||||||||||||||||||
| CissMirrorCtrlExtnSessionIndex | 1.3.6.1.4.1.2076.81.3.6.1.1 | Integer32 (1..20) | NA | ||||||||||||||||||
column · Integer32 (1..20) · not-accessible · current The index of the mirroring session for which the configuration in this entry applies. | |||||||||||||||||||||
| CissMirrorCtrlExtnMirrType | 1.3.6.1.4.1.2076.81.3.6.1.2 | INTEGER | RW | ||||||||||||||||||
column · INTEGER · read-write · current This object tells the type of mirroring this session supports. This object needs to be set before doing any configuration for a mirroring session
| |||||||||||||||||||||
| CissMirrorCtrlExtnRSpanStatus | 1.3.6.1.4.1.2076.81.3.6.1.3 | INTEGER | RW | ||||||||||||||||||
column · INTEGER · read-write · current This object indicates session is enabled or disabled for Remote monitoring. If set as 'source-rspan-vlanid' indicates that the session is enabled for Remote monitoring and the source entities for this session will be remotely monitored. If set as 'destination-rspan-vlanid' indicates that the session should monitor remote traffic mirrored with RSPAN VLAN ID tag. RSPAN VLAN ID should be configured through object 'issMirrorCtrlExtnRSpanVlanId'. If set as 'disabled' Remote monitoring is disabled for this mirroring session.
| |||||||||||||||||||||
| CissMirrorCtrlExtnRSpanVlanId | 1.3.6.1.4.1.2076.81.3.6.1.4 | Integer32 | RW | ||||||||||||||||||
column · Integer32 · read-write · current Vlan Id used for Remote monitoring for this session. If issMirrorCtrlExtnRSpanStatus is set to disabled, then this object will have an invalid value (zero) | |||||||||||||||||||||
| CissMirrorCtrlExtnRSpanContext | 1.3.6.1.4.1.2076.81.3.6.1.5 | Integer32 | RW | ||||||||||||||||||
column · Integer32 · read-write · current Specifies the Context Id to which the RSpan Vlan belongs. Value '0' mean this object is not considered for this mirroring session. | |||||||||||||||||||||
| CissMirrorCtrlExtnStatus | 1.3.6.1.4.1.2076.81.3.6.1.6 | RowStatus | RC | ||||||||||||||||||
column · RowStatus · read-create · current This object indicates the status of the entry. The entry can be made active only if issMirrorCtrlExtnMirrType is configured and source and destination entries for this sesion is also configured | |||||||||||||||||||||
| TissMirrorCtrlExtnSrcTable | 1.3.6.1.4.1.2076.81.3.7 | NA | |||||||||||||||||||
table · not-accessible · current A table to configure list of source entities for mirroring sessions | |||||||||||||||||||||
| RissMirrorCtrlExtnSrcEntry | 1.3.6.1.4.1.2076.81.3.7.1 | NA | |||||||||||||||||||
row · not-accessible · current An entry appears in this table for each mirroring session. | |||||||||||||||||||||
| CissMirrorCtrlExtnSrcId | 1.3.6.1.4.1.2076.81.3.7.1.1 | Integer32 (1..65535) | NA | ||||||||||||||||||
column · Integer32 (1..65535) · not-accessible · current Specifies the source id which participates in a mirroring session. For Port based mirroring this object can be port IfIndex. To mirror Tunnel and Trunk ports the same Id can be used for specifying Tunnel/Trunk Id. For Flow based mirroring this object can be Acl Ids. | |||||||||||||||||||||
| CissMirrorCtrlExtnSrcCfg | 1.3.6.1.4.1.2076.81.3.7.1.2 | INTEGER | RW | ||||||||||||||||||
column · INTEGER · read-write · current This object is used to create/delete a source entry for a session.
| |||||||||||||||||||||
| CissMirrorCtrlExtnSrcMode | 1.3.6.1.4.1.2076.81.3.7.1.3 | INTEGER | RW | ||||||||||||||||||
column · INTEGER · read-write · current Provides control to set the mode of mirroring. It can be ingress, egress, both or disable.
| |||||||||||||||||||||
| TissMirrorCtrlExtnSrcVlanTable | 1.3.6.1.4.1.2076.81.3.8 | NA | |||||||||||||||||||
table · not-accessible · current A table to configure list of vlan source entities for mirroring sessions | |||||||||||||||||||||
| RissMirrorCtrlExtnSrcVlanEntry | 1.3.6.1.4.1.2076.81.3.8.1 | NA | |||||||||||||||||||
row · not-accessible · current An entry appears in this table for each mirroring session. | |||||||||||||||||||||
| CissMirrorCtrlExtnSrcVlanContext | 1.3.6.1.4.1.2076.81.3.8.1.1 | Integer32 (1..64) | NA | ||||||||||||||||||
column · Integer32 (1..64) · not-accessible · current Specifies the Context Id to which the source entity belongs, this is used in case of specifying vlan as source. Value '-1' mean this object is not considered for this mirroring session. | |||||||||||||||||||||
| CissMirrorCtrlExtnSrcVlanId | 1.3.6.1.4.1.2076.81.3.8.1.2 | Integer32 (1..4094) | NA | ||||||||||||||||||
column · Integer32 (1..4094) · not-accessible · current Specifies the Vlan id which participates in a mirroring session. | |||||||||||||||||||||
| CissMirrorCtrlExtnSrcVlanCfg | 1.3.6.1.4.1.2076.81.3.8.1.3 | INTEGER | RW | ||||||||||||||||||
column · INTEGER · read-write · current This object is used to create/delete a vlan entry for a session.
| |||||||||||||||||||||
| CissMirrorCtrlExtnSrcVlanMode | 1.3.6.1.4.1.2076.81.3.8.1.4 | INTEGER | RW | ||||||||||||||||||
column · INTEGER · read-write · current Provides control to set the mode of mirroring. It can be ingerss,Egress or Both.
| |||||||||||||||||||||
| TissMirrorCtrlExtnDestinationTable | 1.3.6.1.4.1.2076.81.3.9 | NA | |||||||||||||||||||
table · not-accessible · current A table to configure list of destination entities | |||||||||||||||||||||
| RissMirrorCtrlExtnDestinationEntry | 1.3.6.1.4.1.2076.81.3.9.1 | NA | |||||||||||||||||||
row · not-accessible · current An entry appears in this table for each destination entity in a mirroring session. | |||||||||||||||||||||
| CissMirrorCtrlExtnDestination | 1.3.6.1.4.1.2076.81.3.9.1.1 | Integer32 (1..65535) | NA | ||||||||||||||||||
column · Integer32 (1..65535) · not-accessible · current Specifies the destination port id which participates in a mirroring session. | |||||||||||||||||||||
| CissMirrorCtrlExtnDestCfg | 1.3.6.1.4.1.2076.81.3.9.1.2 | INTEGER | RW | ||||||||||||||||||
column · INTEGER · read-write · current This object is used to create/delete a destination entry for a session.
| |||||||||||||||||||||
| SissCpuMirrorType | 1.3.6.1.4.1.2076.81.3.10 | INTEGER | RW | disable(4) | |||||||||||||||||
scalar · INTEGER · read-write · current This object is used to set the type of mirroring to be done for CPU traffic. When set to 'ingress(1)', enables mirroring of ingress traffic over CPU port to the CPU mirrored-to port specified in 'issCpuMirrorToPort'. When set to 'egress(2)', enables mirroring of egress traffic over CPU port to the CPU mirrored-to port. specified in 'issCpuMirrorToPort'. When set to 'both(3)', enables mirroring of egress and ingress traffic over CPU port to the CPU mirrored-to port specified in 'issCpuMirrorToPort'. When set to 'disable(4)', CPU mirroring configuration will be removed.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissCpuMirrorToPort | 1.3.6.1.4.1.2076.81.3.11 | Integer32 | RW | 0 | |||||||||||||||||
scalar · Integer32 · read-write · current This object specifies the physical port to which the CPU traffic specified by issCpuMirrorType are mirrored. Example values from LibreNMS test devices
| |||||||||||||||||||||
| NissRateControl | 1.3.6.1.4.1.2076.81.4 | ||||||||||||||||||||
| TissRateCtrlTable | 1.3.6.1.4.1.2076.81.4.1 | NA | deprecated | ||||||||||||||||||
table · not-accessible · deprecated A table to control the rate limiting parameters either for the entire switch or for each interface in the switch. This object is deprecated and the corresponding functionality is met with issRateControl objects in fsissext.mib. | |||||||||||||||||||||
| RissRateCtrlEntry | 1.3.6.1.4.1.2076.81.4.1.1 | NA | deprecated | ||||||||||||||||||
row · not-accessible · deprecated An entry appears in this table for each physical interface in the switch. This object is deprecated and the corresponding functionality is met with issRateControl objects in fsissext.mib.
| |||||||||||||||||||||
| CissRateCtrlIndex | 1.3.6.1.4.1.2076.81.4.1.1.1 | Integer32 (1..65535) | NA | deprecated | |||||||||||||||||
column · Integer32 (1..65535) · not-accessible · deprecated The interface index for which the configuration in this entry applies. This object is deprecated and the corresponding functionality is met with issRateControl objects in fsissext.mib. | |||||||||||||||||||||
| CissRateCtrlDLFLimitValue | 1.3.6.1.4.1.2076.81.4.1.1.2 | Integer32 (0..2147483647) | RW | deprecated | 0 | ||||||||||||||||
column · Integer32 (0..2147483647) · read-write · deprecated Allows to configure the limiting value for the maximum number of dlf packets that can be transmitted per second over this interface. Setting this object to the value zero disables rate limiting for Destination lookup failure packets on this interface. The value that can be set for this object is limited by the underlying hardware This object is deprecated and the corresponding functionality is met with issRateControl objects in fsissext.mib. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CissRateCtrlBCASTLimitValue | 1.3.6.1.4.1.2076.81.4.1.1.3 | Integer32 (0..2147483647) | RW | deprecated | 0 | ||||||||||||||||
column · Integer32 (0..2147483647) · read-write · deprecated Allows to configure the limiting value for the maximum number of broadcast packets that can be transmitted per second over this interface. Setting this object to the value zero disables rate limiting for Broadcast packets on this interface. The value that can be set for this object is limited by the underlying hardware This object is deprecated and the corresponding functionality is met with issRateControl objects in fsissext.mib. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CissRateCtrlMCASTLimitValue | 1.3.6.1.4.1.2076.81.4.1.1.4 | Integer32 (0..2147483647) | RW | deprecated | 0 | ||||||||||||||||
column · Integer32 (0..2147483647) · read-write · deprecated Allows to configure the limiting value for the maximum number of multicast packets that can be transmitted per second over this interface. Setting this object to the value zero disables rate limiting for Multicast packets on this interface. The value that can be set for this object is limited by the underlying hardware This object is deprecated and the corresponding functionality is met with issRateControl objects in fsissext.mib. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CissRateCtrlPortRateLimit | 1.3.6.1.4.1.2076.81.4.1.1.5 | Integer32 (0..80000000) | RW | deprecated | 0 | ||||||||||||||||
column · Integer32 (0..80000000) · read-write · deprecated Configures interface Rate Limit (Packet that can be transferred on a port at a particular second). This object's value will take effect on the interface speed. Based on the operating speed of the port, the rate limit will be applied. This value can also be affected by the metering. A value of zero(0) disable rate limiting i.e. sets the port to full speed. This object is deprecated and the corresponding functionality is met with issRateControl objects in fsissext.mib. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CissRateCtrlPortBurstSize | 1.3.6.1.4.1.2076.81.4.1.1.6 | Integer32 (0..80000000) | RW | deprecated | 0 | ||||||||||||||||
column · Integer32 (0..80000000) · read-write · deprecated Configures interface Burst Pkt Rate. (Packet Burst that can be transferred on a port at a particular second) This object's value will take effect on the interface speed. Based on the operating speed of the port, the burst size of the port will be applied. This value can also be affected by the metering. A value of zero(0) disable burst rate limiting i.e. sets the port burst rate limit to full speed. This object is deprecated and the corresponding functionality is met with issRateControl objects in fsissext.mib. Example values from LibreNMS test devices
| |||||||||||||||||||||
| NissL2Filter | 1.3.6.1.4.1.2076.81.5 | ||||||||||||||||||||
| TissL2FilterTable | 1.3.6.1.4.1.2076.81.5.1 | NA | deprecated | ||||||||||||||||||
table · not-accessible · deprecated A table to configure L2 filter rules in the system. This object is deprecated and the corresponding functionality is met with issL2Filter objects in fsissext.mib. | |||||||||||||||||||||
| RissL2FilterEntry | 1.3.6.1.4.1.2076.81.5.1.1 | NA | deprecated | ||||||||||||||||||
row · not-accessible · deprecated Each entry in this table is a L2 filter rule.Index to the table is the L2 filter number.This object is deprecated and the corresponding functionality is met with issL2Filter objects in fsissext.mib.
| |||||||||||||||||||||
| CissL2FilterNo | 1.3.6.1.4.1.2076.81.5.1.1.1 | Integer32 (1..65535) | NA | ||||||||||||||||||
column · Integer32 (1..65535) · not-accessible · current L2 Filter rule number. This object is deprecated and the corresponding functionality is met with issL2Filter objects in fsissext.mib. | |||||||||||||||||||||
| CissL2FilterPriority | 1.3.6.1.4.1.2076.81.5.1.1.2 | Integer32 (1..255) | RW | ||||||||||||||||||
column · Integer32 (1..255) · read-write · current The priority of the L2 filter can be used to decide which filter rule
is applicable when
--> the packet matches with more than one filter rules
--> All the filter rules result in 'allow'ing the packet
Higher value of 'filter priority' implies a higher priority.
Usage of 'L2FilterPriority' is implementation dependant.
This object is deprecated and the corresponding functionality is
met with issL2Filter objects in fsissext.mib. | |||||||||||||||||||||
| CissL2FilterEtherType | 1.3.6.1.4.1.2076.81.5.1.1.3 | Integer32 (0..65535) | RW | deprecated | |||||||||||||||||
column · Integer32 (0..65535) · read-write · deprecated The value in the Type/Len field of a frame that will be matched to trigger this filter. The default value of this object is '0'. When this object is SET with the default value, frames are not matched for the value in the Type/Len field with the value set for this object. This object is deprecated and the corresponding functionality is met with issL2Filter objects in fsissext.mib. | |||||||||||||||||||||
| CissL2FilterProtocolType | 1.3.6.1.4.1.2076.81.5.1.1.4 | Unsigned32 (0..65535) | RW | deprecated | |||||||||||||||||
column · Unsigned32 (0..65535) · read-write · deprecated Specifies the non IP protocol type to be filtered. aarp | amber | dec-spanning | decnet-iv | diagnostic | dsm |etype-6000 | etype-8042 | lat | lavc-sca | mop-console | mop-dump | msdos | mumps | netbios | vines-echo | vines-ip | xns-idp: A non-IP protocol. A value of '0' means, the filter is applicable for all protocols. This object is deprecated and the corresponding functionality is met with issL2Filter objects in fsissext.mib. | |||||||||||||||||||||
| CissL2FilterDstMacAddr | 1.3.6.1.4.1.2076.81.5.1.1.5 | MacAddress | RW | deprecated | |||||||||||||||||
column · MacAddress · read-write · deprecated Destination MAC address to be matched with the packet. By Default, the Destination Mac Address will be zero which means dont care condition ie) any Dst Mac Address .This object is deprecated and the corresponding functionality is met with issL2Filter objects in fsissext.mib. | |||||||||||||||||||||
| CissL2FilterSrcMacAddr | 1.3.6.1.4.1.2076.81.5.1.1.6 | MacAddress | RW | deprecated | |||||||||||||||||
column · MacAddress · read-write · deprecated Source MAC address to be matched with the packet. By Default, the Source Mac Address will be zero which means dont care condition ie) any Src Mac address This object is deprecated and the corresponding functionality is met with issL2Filter objects in fsissext.mib. | |||||||||||||||||||||
| CissL2FilterVlanId | 1.3.6.1.4.1.2076.81.5.1.1.7 | Integer32 (0..4094) | RW | deprecated | |||||||||||||||||
column · Integer32 (0..4094) · read-write · deprecated Vlan Id to be filtered. In case of Provider bridges, This Vlan Id will be treated as customer Vlan Id. A value of '0' means, this object is unused. Configuring this value is not allowed. This object is deprecated and the corresponding functionality is met with issL2Filter objects in fsissext.mib. | |||||||||||||||||||||
| CissL2FilterInPortList | 1.3.6.1.4.1.2076.81.5.1.1.8 | PortList | RW | deprecated | |||||||||||||||||
column · PortList · read-write · deprecated Specifies the complete set of ports over which this filter is applied for packets ingress at ports in this list. If the In port list is '0', the filter rule is applicable for the incoming packets on all ports. Even though the issL2FilterInPortList is configured, It is applicable only if issL2FilterDirection is configured as 'in'. By default inport list is maintained as '0'. This object is deprecated and the corresponding functionality is met with issL2Filter objects in fsissext.mib. | |||||||||||||||||||||
| CissL2FilterAction | 1.3.6.1.4.1.2076.81.5.1.1.9 | INTEGER | RW | deprecated | |||||||||||||||||
column · INTEGER · read-write · deprecated Specifies the action to be taken on the packet if the filter rule matches. If the action is 'allow', the packet will be forwarded according to the forwarding rules. If the action is 'drop', the packet will be discarded. This object is deprecated and the corresponding functionality is met with issL2Filter objects in fsissext.mib.
| |||||||||||||||||||||
| CissL2FilterMatchCount | 1.3.6.1.4.1.2076.81.5.1.1.10 | Counter32 | RO | deprecated | |||||||||||||||||
column · Counter32 · read-only · deprecated Number of times this filter is matched. This object is deprecated and the corresponding functionality is met with issL2Filter objects in fsissext.mib. | |||||||||||||||||||||
| CissL2FilterStatus | 1.3.6.1.4.1.2076.81.5.1.1.11 | RowStatus | RC | deprecated | |||||||||||||||||
column · RowStatus · read-create · deprecated This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy'. This object is deprecated and the corresponding functionality is met with issL2Filter objects in fsissext.mib. | |||||||||||||||||||||
| CissL2FilterOutPortList | 1.3.6.1.4.1.2076.81.5.1.1.12 | PortList | RW | deprecated | |||||||||||||||||
column · PortList · read-write · deprecated Specifies the complete set of ports over which this filter is applied for packets egress at Ports in this list. If the Out port list is '0', the filter rule is applicable for the outgoing packets on all ports. Even though the issL2FilterOutPortList is configured, It is applicable only if issL2FilterDirection is configured as 'out'. By default outport list is maintained as '0'. This object is deprecated and the corresponding functionality is met with issL2Filter objects in fsissext.mib. | |||||||||||||||||||||
| CissL2FilterDirection | 1.3.6.1.4.1.2076.81.5.1.1.13 | INTEGER | RW | deprecated | |||||||||||||||||
column · INTEGER · read-write · deprecated Specifies the direction of this filter to be applied. By Default the filter will be applied on ingress direction. When the direction of this filter is 'in', It is applied on specified ports of the issL2FilterInPortList. When the direction of this filter is 'out', It is applied on specified ports of the issL2FilterOutPortList. This object is deprecated and the corresponding functionality is met with issL2Filter objects in fsissext.mib.
| |||||||||||||||||||||
| NissL3Filter | 1.3.6.1.4.1.2076.81.6 | ||||||||||||||||||||
| TissL3FilterTable | 1.3.6.1.4.1.2076.81.6.1 | NA | deprecated | ||||||||||||||||||
table · not-accessible · deprecated A table to configure L3 filter rules in the system. This object is deprecated and the corresponding functionality is met with issL3Filter objects in fsissext.mib. | |||||||||||||||||||||
| RissL3FilterEntry | 1.3.6.1.4.1.2076.81.6.1.1 | NA | deprecated | ||||||||||||||||||
row · not-accessible · deprecated Each entry in this table is a L3 filter rule. Index to the table is L3 filter number. This object is deprecated and the corresponding functionality is met with issL3Filter objects in fsissext.mib.
| |||||||||||||||||||||
| CissL3FilterNo | 1.3.6.1.4.1.2076.81.6.1.1.1 | Integer32 (1..65535) | NA | deprecated | |||||||||||||||||
column · Integer32 (1..65535) · not-accessible · deprecated L3 Filter rule number. This object is deprecated and the corresponding functionality is met with issL3Filter objects in fsissext.mib. | |||||||||||||||||||||
| CissL3FilterPriority | 1.3.6.1.4.1.2076.81.6.1.1.2 | Integer32 (1..255) | RW | deprecated | |||||||||||||||||
column · Integer32 (1..255) · read-write · deprecated The priority of the filter can be used to decide which filter rule
is applicable when
--> the packet matches with more than one filter rules
--> All the filter rules result in 'allow'ing the packet
Higher value of 'L3 filter priority' implies a higher priority.
Usage of 'L3FilterPriority' is implementation dependant.
This object is deprecated and the corresponding functionality is
met with issL3Filter objects in fsissext.mib. | |||||||||||||||||||||
| CissL3FilterProtocol | 1.3.6.1.4.1.2076.81.6.1.1.3 | Integer32 (0..255) | RW | deprecated | |||||||||||||||||
column · Integer32 (0..255) · read-write · deprecated The type of protocol to be checked against the packet. The default value is 255. If the value is 255, it means that the protocol type can be anything and it will not be checked to decide the action. This object is deprecated and the corresponding functionality is met with issL3Filter objects in fsissext.mib. | |||||||||||||||||||||
| CissL3FilterMessageType | 1.3.6.1.4.1.2076.81.6.1.1.4 | Integer32 (0..65535) | RW | deprecated | |||||||||||||||||
column · Integer32 (0..65535) · read-write · deprecated The message type to be checked against the packet. If the
message type matches with the packet, then the packet will be
dropped / allowed based on the action set in issL3FilterAction.
The default value is 255. It means that message type is not
configured and need not be checked.
Generally the value zero is given as default. But here
zero can be an ICMP Type value. Hence 255 is given as the
default value.
Some ICMP message types are:
echoReply(0),
destinationUnreachable(3),
sourceQuench(4),
redirect(5),
echoRequest(8),
timeExceeded(11),
parameterProblem(12),
timestampRequest(13),
timestampReply(14),
informationRequest(15),
informationReply(16),
addressMaskRequest(17),
addressMaskReply (18),
noICMPType(255)
This object is deprecated and the corresponding functionality is
met with issL3Filter objects in fsissext.mib. | |||||||||||||||||||||
| CissL3FilterMessageCode | 1.3.6.1.4.1.2076.81.6.1.1.5 | Integer32 (0..65535) | RW | deprecated | |||||||||||||||||
column · Integer32 (0..65535) · read-write · deprecated The message code to be checked against the packet. If the
packet matches with the message code, then the packet will
be dropped / allowed based on the action set in issL3FilterAction.
The default value is 255. It means that message code is not
configured and need not be checked. Generally the value zero
will be given as default. But here, zero can be an ICMP Code
value. Hence 255 is given as the default value.
Some ICMP message codes are :
networkUnreachable(0),
hostUnreachable(1),
protocolUnreachable(2),
portUnreachable(3),
fragmentNeed(4),
sourceRouteFail(5),
destNetworkUnknown(6),
destHostUnknown(7),
srcHostIsolated(8),
destNetworkAdminProhibited(9),
destHostAdminProhibited(10),
networkUnreachableTOS(11),
hostUnreachableTOS(12),
noICMPCode(255)
This object is deprecated and the corresponding functionality is
met with issL3Filter objects in fsissext.mib. | |||||||||||||||||||||
| CissL3FilterDstIpAddr | 1.3.6.1.4.1.2076.81.6.1.1.6 | IpAddress | RW | deprecated | |||||||||||||||||
column · IpAddress · read-write · deprecated Destination IP address to be matched with the packet. This object is valid only if the 'issFilterType' is 'l3filter'. This object is deprecated and the corresponding functionality is met with issL3Filter objects in fsissext.mib. | |||||||||||||||||||||
| CissL3FilterSrcIpAddr | 1.3.6.1.4.1.2076.81.6.1.1.7 | IpAddress | RW | deprecated | |||||||||||||||||
column · IpAddress · read-write · deprecated Source IP address to be matched with the packet. This object is valid only if the 'issFilterType' is 'l3filter' This object is deprecated and the corresponding functionality is met with issL3Filter objects in fsissext.mib. | |||||||||||||||||||||
| CissL3FilterDstIpAddrMask | 1.3.6.1.4.1.2076.81.6.1.1.8 | IpAddress | RW | deprecated | |||||||||||||||||
column · IpAddress · read-write · deprecated The IP subnet mask for Destination IP address. This object is valid only if the 'issFilterType' is 'l3filter' This object is deprecated and the corresponding functionality is met with issL3Filter objects in fsissext.mib. | |||||||||||||||||||||
| CissL3FilterSrcIpAddrMask | 1.3.6.1.4.1.2076.81.6.1.1.9 | IpAddress | RW | deprecated | |||||||||||||||||
column · IpAddress · read-write · deprecated The IP subnet mask for Source IP address. This object is valid only if the 'issFilterType' is 'l3filter'. This object is deprecated and the corresponding functionality is met with issL3Filter objects in fsissext.mib. | |||||||||||||||||||||
| CissL3FilterMinDstProtPort | 1.3.6.1.4.1.2076.81.6.1.1.10 | Unsigned32 | RW | deprecated | |||||||||||||||||
column · Unsigned32 · read-write · deprecated The minimum port in the destination port range. Please note these ports are the TCP / UDP ports. This object is deprecated and the corresponding functionality is met with issL3Filter objects in fsissext.mib. | |||||||||||||||||||||
| CissL3FilterMaxDstProtPort | 1.3.6.1.4.1.2076.81.6.1.1.11 | Unsigned32 | RW | deprecated | |||||||||||||||||
column · Unsigned32 · read-write · deprecated The maximum port in the destination port range. Please note these ports are the TCP / UDP ports. This object is deprecated and the corresponding functionality is met with issL3Filter objects in fsissext.mib. | |||||||||||||||||||||
| CissL3FilterMinSrcProtPort | 1.3.6.1.4.1.2076.81.6.1.1.12 | Unsigned32 | RW | deprecated | |||||||||||||||||
column · Unsigned32 · read-write · deprecated The minimum port in the source port range. Please note these ports are the TCP / UDP ports. This object is deprecated and the corresponding functionality is met with issL3Filter objects in fsissext.mib. | |||||||||||||||||||||
| CissL3FilterMaxSrcProtPort | 1.3.6.1.4.1.2076.81.6.1.1.13 | Unsigned32 | RW | deprecated | |||||||||||||||||
column · Unsigned32 · read-write · deprecated The maximum port in the source port range. Please note these ports are the TCP / UDP ports. This object is deprecated and the corresponding functionality is met with issL3Filter objects in fsissext.mib. | |||||||||||||||||||||
| CissL3FilterInPortList | 1.3.6.1.4.1.2076.81.6.1.1.14 | PortList | RW | deprecated | |||||||||||||||||
column · PortList · read-write · deprecated Specifies the complete set of ports over which if the packet arrives this filter rule will be applicable. If the incoming port list is '0', the filter rule is applicable for all the incoming ports. By default inport list is maintained as '0'. This object is deprecated and the corresponding functionality is met with issL3Filter objects in fsissext.mib. | |||||||||||||||||||||
| CissL3FilterOutPortList | 1.3.6.1.4.1.2076.81.6.1.1.15 | PortList | RW | deprecated | |||||||||||||||||
column · PortList · read-write · deprecated Specifies the complete set of ports over which if the packet goes out, this filter rule will be applicable. If the outgoing port list is '0',the filter rule is applicable for all the outgoing packets in all ports. By default outport list is maintained as '0' This object is deprecated and the corresponding functionality is met with issL3Filter objects in fsissext.mib. | |||||||||||||||||||||
| CissL3FilterAckBit | 1.3.6.1.4.1.2076.81.6.1.1.16 | INTEGER | RC | deprecated | |||||||||||||||||
column · INTEGER · read-create · deprecated The TCP ACK bit to be checked against the packet. The default
value is 'any'(3). It means that ACK bit will not be checked
to decide the action.
This object is deprecated and the corresponding functionality is
met with issL3Filter objects in fsissext.mib.
| |||||||||||||||||||||
| CissL3FilterRstBit | 1.3.6.1.4.1.2076.81.6.1.1.17 | INTEGER | RC | deprecated | |||||||||||||||||
column · INTEGER · read-create · deprecated The TCP RST bit to be checked against the packet. The default
value is 'any'(3). It means that RST bit will not be checked to
decide the action.
This object is deprecated and the corresponding functionality is
met with issL3Filter objects in fsissext.mib.
| |||||||||||||||||||||
| CissL3FilterTos | 1.3.6.1.4.1.2076.81.6.1.1.18 | Integer32 (-1..7) | RC | deprecated | |||||||||||||||||
column · Integer32 (-1..7) · read-create · deprecated The IP TOS bit to be checked against the packet. This is a
single byte integer of which the last three bits (least
significant bits) indicate Delay, Throughput and Reliability
i.e 'uuuuudtr', u-unused, d-delay, t-throughput, r-reliability.
For example '6' indicates low delay and high throughput.
A value of '-1' means, the Tos Field becomes dont care
This object is deprecated and the corresponding functionality is
met with issL3Filter objects in fsissext.mib. | |||||||||||||||||||||
| CissL3FilterDscp | 1.3.6.1.4.1.2076.81.6.1.1.19 | Integer32 (-1..63) | RC | deprecated | |||||||||||||||||
column · Integer32 (-1..63) · read-create · deprecated The IP Dscp value to be checked against the packet. A value of '-1' means, the Dscp Field becomes dont care. This object is deprecated and the corresponding functionality is met with issL3Filter objects in fsissext.mib. | |||||||||||||||||||||
| CissL3FilterDirection | 1.3.6.1.4.1.2076.81.6.1.1.20 | INTEGER | RW | deprecated | |||||||||||||||||
column · INTEGER · read-write · deprecated Specifies the direction of this filter to be applied. By Default the filter will be applied on ingress direction. When the direction of this filter is 'in', It is applied on specified ports of the issL3FilterInPortList. When the direction of this filter is 'out', It is applied on specified ports of the issL3FilterOutPortList.This object is deprecated and the corresponding functionality is met with issL3Filter objects in fsissext.mib.
| |||||||||||||||||||||
| CissL3FilterAction | 1.3.6.1.4.1.2076.81.6.1.1.21 | INTEGER | RW | deprecated | |||||||||||||||||
column · INTEGER · read-write · deprecated Specifies the action to be taken on the packet if the filter rule matches. If the action is 'allow', the packet will be sent to the ports in 'out port list'. If the out port list is '0', the port over which the packet is to be switched will be decided based on further processing on the packet. If the action is 'drop', the packet will be discardedThis object is deprecated and the corresponding functionality is met with issL3Filter objects in fsissext.mib.
| |||||||||||||||||||||
| CissL3FilterMatchCount | 1.3.6.1.4.1.2076.81.6.1.1.22 | Counter32 | RO | deprecated | |||||||||||||||||
column · Counter32 · read-only · deprecated Number of times this filter is matched. This object is deprecated and the corresponding functionality is met with issL3Filter objects in fsissext.mib. | |||||||||||||||||||||
| CissL3FilterStatus | 1.3.6.1.4.1.2076.81.6.1.1.23 | RowStatus | RC | deprecated | |||||||||||||||||
column · RowStatus · read-create · deprecated This object indicates the status of this entry. An entry is created in this table when this object is SET to 'createAndWait'. The entry in this table is used when the status of this object is SET 'active'. The entry in this table is not used when this object is SET 'notInService'. An entry created in this table is be deleted when this object is SET 'destroy.This object is deprecated and the corresponding functionality is met with issL3Filter objects in fsissext.mib. | |||||||||||||||||||||
| NissIpAuthMgr | 1.3.6.1.4.1.2076.81.7 | ||||||||||||||||||||
| TissIpAuthMgrTable | 1.3.6.1.4.1.2076.81.7.1 | NA | |||||||||||||||||||
table · not-accessible · current A table to configure IP authorized managers in the system. | |||||||||||||||||||||
| RissIpAuthMgrEntry | 1.3.6.1.4.1.2076.81.7.1.1 | NA | |||||||||||||||||||
row · not-accessible · current Each entry in this table represents rules for particular IP authorized manager. | |||||||||||||||||||||
| CissIpAuthMgrIpAddr | 1.3.6.1.4.1.2076.81.7.1.1.1 | IpAddress | NA | ||||||||||||||||||
column · IpAddress · not-accessible · current Specifies either the Network or Host address from which the switch can be managed. An address 0.0.0.0 indicates 'Any Manager'. | |||||||||||||||||||||
| CissIpAuthMgrIpMask | 1.3.6.1.4.1.2076.81.7.1.1.2 | IpAddress | NA | ||||||||||||||||||
column · IpAddress · not-accessible · current Specifies the IP address mask to be applied on issIpAuthMgrIpAddr. Value 0.0.0.0 indicates mask for 'Any Manager'. | |||||||||||||||||||||
| CissIpAuthMgrPortList | 1.3.6.1.4.1.2076.81.7.1.1.3 | PortList | RW | ||||||||||||||||||
column · PortList · read-write · current Specifies the port numbers through which the authorized manager can access the switch. By default the authorized manager is allowed to access the switch through all the ports. If a set of ports are configured in the 'PortList', the manager can access the switch only through the configured ports. | |||||||||||||||||||||
| CissIpAuthMgrVlanList | 1.3.6.1.4.1.2076.81.7.1.1.4 | OCTET STRING | RW | ||||||||||||||||||
column · OCTET STRING · read-write · current Specifies the Vlan's in which the IP authorized manager can reside. By default the manager is allowed to reside in any vlan. If a set of vlans are configured in the 'VlanList', the manager can reside only in the configured vlan set. Access to the switch will be denied from any other vlan. | |||||||||||||||||||||
| CissIpAuthMgrOOBPort | 1.3.6.1.4.1.2076.81.7.1.1.5 | TruthValue | RW | ||||||||||||||||||
column · TruthValue · read-write · current Specifies whether the authorized manager can access the switch through OOB Port By default the manager is denied access to reside on OOB Interface | |||||||||||||||||||||
| CissIpAuthMgrAllowedServices | 1.3.6.1.4.1.2076.81.7.1.1.6 | Integer32 | RW | ||||||||||||||||||
column · Integer32 · read-write · current Specifies the allowed services through which the authorized manager can
access the switch.
This object takes bit mask values. The services represented by each bit
position is as given below:
With bit 0 being the Least Significant Bit,
Bit0 --> snmp
Bit1 --> telnet
Bit2 --> http
Bit3 --> https
Bit4 --> ssh
If the particular bit is set to 1,corresponding service is allowed for
the configured manager.
By default all services are allowed for the configured manager. | |||||||||||||||||||||
| CissIpAuthMgrRowStatus | 1.3.6.1.4.1.2076.81.7.1.1.7 | RowStatus | RC | ||||||||||||||||||
column · RowStatus · read-create · current This object indicates the status of this entry. | |||||||||||||||||||||
| NissExt | 1.3.6.1.4.1.2076.81.8 | ||||||||||||||||||||
| NissL4Switching | 1.3.6.1.4.1.2076.81.9 | ||||||||||||||||||||
| TissL4SwitchingFilterTable | 1.3.6.1.4.1.2076.81.9.1 | NA | |||||||||||||||||||
table · not-accessible · current A table to L4 Switching rules in the system. | |||||||||||||||||||||
| RissL4SwitchingFilterEntry | 1.3.6.1.4.1.2076.81.9.1.1 | NA | |||||||||||||||||||
row · not-accessible · current Each entry in this table is a L4 Switching rule. Index to the table is L4 filter number. | |||||||||||||||||||||
| CissL4SwitchingFilterNo | 1.3.6.1.4.1.2076.81.9.1.1.1 | Integer32 (1..65535) | NA | ||||||||||||||||||
column · Integer32 (1..65535) · not-accessible · current L4 Switching Filter rule number. | |||||||||||||||||||||
| CissL4SwitchingProtocol | 1.3.6.1.4.1.2076.81.9.1.1.2 | Integer32 (0..255) | RW | ||||||||||||||||||
column · Integer32 (0..255) · read-write · current The type of protocol to be checked against the packet. The default value is 255. If the value is 255, it means that the protocol type can be anything and it will not be checked to decide the action. | |||||||||||||||||||||
| CissL4SwitchingPortNo | 1.3.6.1.4.1.2076.81.9.1.1.3 | Unsigned32 | RW | ||||||||||||||||||
column · Unsigned32 · read-write · current The Layer 4 port no. Please note these ports are the TCP / UDP ports. | |||||||||||||||||||||
| CissL4SwitchingCopyToPort | 1.3.6.1.4.1.2076.81.9.1.1.4 | Integer32 (0..65535) | RW | ||||||||||||||||||
column · Integer32 (0..65535) · read-write · current This object is Port to which the packet would be switched | |||||||||||||||||||||
| CissL4SwitchingFilterStatus | 1.3.6.1.4.1.2076.81.9.1.1.5 | RowStatus | RC | ||||||||||||||||||
column · RowStatus · read-create · current This object indicates the status of this entry. | |||||||||||||||||||||
| NissSystemTrap | 1.3.6.1.4.1.2076.81.10 | ||||||||||||||||||||
| SissMsrFailedOid | 1.3.6.1.4.1.2076.81.10.1 | OBJECT IDENTIFIER | AN | ||||||||||||||||||
scalar · OBJECT IDENTIFIER · accessible-for-notify · current Indicates the OID for which updation failure has occured at MSR | |||||||||||||||||||||
| SissMsrFailedValue | 1.3.6.1.4.1.2076.81.10.2 | DisplayString | AN | ||||||||||||||||||
scalar · DisplayString · accessible-for-notify · current Indicates the value of corresponding OID for which updation failure has occured at MSR | |||||||||||||||||||||
| NissAuditTrap | 1.3.6.1.4.1.2076.81.11 | ||||||||||||||||||||
| SissAuditTrapEvent | 1.3.6.1.4.1.2076.81.11.1 | INTEGER | AN | ||||||||||||||||||
scalar · INTEGER · accessible-for-notify · current openFailed - Open operation on Audit File failed. writeFailed - Write operation on Audit File failed. sizeExceeded - Audit File Size exceeded. sizeThresholdHit - Audit Log Size Hit the threshold value.
| |||||||||||||||||||||
| SissAuditTrapEventTime | 1.3.6.1.4.1.2076.81.11.2 | DisplayString (SIZE (24)) | AN | ||||||||||||||||||
scalar · DisplayString (SIZE (24)) · accessible-for-notify · current This object specifies the date and time at which fsAuditTrapEvent was performed. | |||||||||||||||||||||
| SissAuditTrapFileName | 1.3.6.1.4.1.2076.81.11.3 | DisplayString (SIZE (1..128)) | RO | /backup/config.txt | |||||||||||||||||
scalar · DisplayString (SIZE (1..128)) · read-only · current Audit File name in the trap message. Example values from LibreNMS test devices
| |||||||||||||||||||||
| NissModule | 1.3.6.1.4.1.2076.81.12 | ||||||||||||||||||||
| TissModuleTable | 1.3.6.1.4.1.2076.81.12.1 | NA | |||||||||||||||||||
table · not-accessible · current A table for triggering Graceful shutdown and Start | |||||||||||||||||||||
| RissModuleEntry | 1.3.6.1.4.1.2076.81.12.1.1 | NA | |||||||||||||||||||
row · not-accessible · current Each entry in this table corresponding to one protocol
| |||||||||||||||||||||
| CissModuleId | 1.3.6.1.4.1.2076.81.12.1.1.1 | Integer32 (1..65535) | NA | ||||||||||||||||||
column · Integer32 (1..65535) · not-accessible · current This object indicates the ID of the protocol. Following IDs are supported. 1. OSPF 2. OSPFV3 3. BGP 4. ISIS 5. RSVPTE 6. LDP | |||||||||||||||||||||
| CissModuleSystemControl | 1.3.6.1.4.1.2076.81.12.1.1.2 | INTEGER | RW | start(2) | |||||||||||||||||
column · INTEGER · read-write · current This object shuts and starts the process
Example values from LibreNMS test devices
| |||||||||||||||||||||
| NissSwitchFan | 1.3.6.1.4.1.2076.81.13 | ||||||||||||||||||||
| TissSwitchFanTable | 1.3.6.1.4.1.2076.81.13.1 | NA | |||||||||||||||||||
table · not-accessible · current Table containing the Fan information. | |||||||||||||||||||||
| RissSwitchFanEntry | 1.3.6.1.4.1.2076.81.13.1.1 | NA | |||||||||||||||||||
row · not-accessible · current Indicates information related to fan status of the switch.
| |||||||||||||||||||||
| CissSwitchFanIndex | 1.3.6.1.4.1.2076.81.13.1.1.1 | Integer32 (1..5) | NA | ||||||||||||||||||
column · Integer32 (1..5) · not-accessible · current Indicates the fan number in the switch | |||||||||||||||||||||
| CissSwitchFanStatus | 1.3.6.1.4.1.2076.81.13.1.1.2 | INTEGER | RO | normal(1) | |||||||||||||||||
column · INTEGER · read-only · current Indicates the fan status of the switch.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| NissAclNp | 1.3.6.1.4.1.2076.81.14 | ||||||||||||||||||||
| SissAclProvisionMode | 1.3.6.1.4.1.2076.81.14.1 | INTEGER | RW | immediate(1) | |||||||||||||||||
scalar · INTEGER · read-write · current The MIB object issAclProvisionMode is used to configure the mode for provisioning active Filter Rules to the hardware. This object takes values immediate/consolidated. When this object is set to immediate, active ACL rules are programmed to hardware immediately. This is the default mode. In this mode, the sequence of configuration determines the order of provisioning the Filter rule to the hardware. When this object is set to consolidated, active Filter Rules are provisioned whenever a commit is triggered using MIB object issAclTriggerCommit. In the consolidated mode, the Filter rules are programmed/re-programmed to hardware in the order of configured priority.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissAclTriggerCommit | 1.3.6.1.4.1.2076.81.14.2 | INTEGER | RW | false(0) | |||||||||||||||||
scalar · INTEGER · read-write · current The MIB object issAclTriggerCommit takes values true(1)/false (0). A SET on this object ( only true is allowed) triggers the programming of active ACL entries to the device based on configured priority.After completion of the operation, this MIB object is reset to false( 0) .This object is applicable only when the MIB object issAclProvisionMode is set to ' consolidated. A set on this object will impact the existing traffic flow as existing Filter entries are deleted and re-programmed to hardware based on configured priority. Filter entries that are associated with quality-of-service configurations will also be impacted when this object triggers the re-programming of the active ACL entries to the hardware. The administrator needs to ensure that corresponding Filter entries are de-provisioned before triggering commit.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| NissAclTrafficControl | 1.3.6.1.4.1.2076.81.15 | ||||||||||||||||||||
| SissAclTrafficSeperationCtrl | 1.3.6.1.4.1.2076.81.15.1 | INTEGER | RW | none(3) | |||||||||||||||||
scalar · INTEGER · read-write · current This object provides control to administrator, to have system default or user defined ACL/QoS rules to carry control traffic to CPU. system-default: ACL/QoS rules for all the control packets will be automatically installed by the ISS software at system init time.Either a 'switch-and-copy-to-cpu'filter (or) 'drop-and-copy-to-cpu' filter will be installed, as appropriate, for getting the control packets to CPU, for processing. Each ACL rule will be associated with class-map, meter and policy map with protocol ID, and CPU queue number user-config: The ACL/QoS rules for receiving all the control packets to CPU for processing, will NOT be automatically installed by the the ISS software.The administrator is expected to install required rules for the control packets as requried. none: ACL/QoS rules for all the control packets will be automatically installed by the ISS software at system init time.Either a 'switch-and-co py-to-cpu'filter (or) 'drop-and-copy-to-cpu' filter will be installed, as appropriate, for getting the control packets to CPU, for processing. Default mode is none If the configuration is changed from 'systemdefault' to 'userconfig' option, then all the default ACL/QoS rules for carrying protocol control packets to CPU are removed.Then user has to install the specific ACL/QoS rules, to carry the intended control packets to CPU for the processing. If the configuration is changed from 'userconfig' to 'systemdefault', all the default ACL/QoS rules are installed. Already existing(if any) user configured ACL rules in the system are not removed. If the configuration is changed from 'none' to 'systemdefault' option, then all the default ACL filters for carrying protocol control packets to CPU are removed and new set of filters will be installed. Each filter will be associated with Qos rules. If the configuration is changed from 'none' to 'userconfig' option, then all the default ACL filters for carrying protocol control packets to CPU are removed.Then user has to install the specific ACL/QoS rules, to carry the intended control packets to CPU for the processing. If the configuration is changed from 'userconfig' to 'none' all the default ACL filters are installed. Already existing(if any) user configured ACL rules in the system are not removed. Above three options can be configured during system runtime.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| NissLogTrap | 1.3.6.1.4.1.2076.81.16 | ||||||||||||||||||||
| SissLogTrapEvent | 1.3.6.1.4.1.2076.81.16.1 | INTEGER | AN | ||||||||||||||||||
scalar · INTEGER · accessible-for-notify · current openFailed - Open operation on Log File failed. writeFailed - Write operation on Log File failed. sizeExceeded - Log File Size exceeded. sizeThresholdHit - Log Size Hit the threshold value.
| |||||||||||||||||||||
| SissLogTrapEventTime | 1.3.6.1.4.1.2076.81.16.2 | DisplayString (SIZE (24)) | AN | ||||||||||||||||||
scalar · DisplayString (SIZE (24)) · accessible-for-notify · current This object specifies the date and time at which fsLogTrapEvent was performed. | |||||||||||||||||||||
| SissLogTrapFileName | 1.3.6.1.4.1.2076.81.16.3 | DisplayString (SIZE (1..128)) | RO | ||||||||||||||||||
scalar · DisplayString (SIZE (1..128)) · read-only · current Log File name in the trap message. | |||||||||||||||||||||
| NissHealthCheckGroup | 1.3.6.1.4.1.2076.81.17 | ||||||||||||||||||||
| SissHealthChkStatus | 1.3.6.1.4.1.2076.81.17.1 | INTEGER | RO | upAndRunning(1) | |||||||||||||||||
scalar · INTEGER · read-only · current upAndRunning(1), This status indicates that ISS is up and running and carrying out its job smoothly. downNonRecoverableErr(2), This indicates that the health status of ISS is down due to occurence of some non-recoverable error. upRecoverableRuntimeErr(3), This indicates that the health status of ISS is up but indicates the occurence of a runtime error that is recoverable.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissHealthChkErrorReason | 1.3.6.1.4.1.2076.81.17.2 | INTEGER | RO | 0 | |||||||||||||||||
scalar · INTEGER · read-only · current When the MIB object 'issHealthChkStatus' indicates health as down, this object provides the reason for errors encountered. nonRecovTaskInitializationFailure(1), Indicates the occurence of non-recoverable failure during Task initialization. nonRecovInsufficientStartupMemory(2), Indicates that there is insufficient memory for successful startup. This error is non-recoverable and requires sufficient memory to be available in the system for successful ISS startup. recovCruBuffExhausted(3), Indicates that CRU Buffer Exhausted. recovConfigRestoreFailed(4), Indicates that config-restore failed for ISS. This is a recoverable error. recovProtocolMemPoolExhausted(5), Indicates that a mem-pool associated with a specific module in ISS has drained out. This error may affect the functioning of the specific protocol alone and is treated as a recoverable error. By default issHealthChkErrorReason is 0.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissHealthChkMemAllocErrPoolId | 1.3.6.1.4.1.2076.81.17.3 | Integer32 | RO | 0 | |||||||||||||||||
scalar · Integer32 · read-only · current This object retrieves the mem-pool identifier for which memory allocation failure was encountered at run-time.This object will get updated when MIB object fsISSHealthChkErrorReason takes value of recovProtocolMemPoolExhausted (5). Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissHealthChkConfigRestoreStatus | 1.3.6.1.4.1.2076.81.17.4 | INTEGER | RO | configRestoreSuccess(1) | |||||||||||||||||
scalar · INTEGER · read-only · current configRestoreSuccess(1), Indicates that configuration restore operation
was successfully done.
configRestoreFailed(2),Indicates that configuration restoration was unsuccessful.
configRestoreInProgress(3), Indicates that configuration restore operation is in-progress for ISS.
configRestoreDefault(4), Indicates the absence of config-restore file (iss.conf)
and that ISS was started with default values.
By default issHealthChkConfigRestoreStatus is 4.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| SissHealthChkClearCtr | 1.3.6.1.4.1.2076.81.17.5 | Bits | RW | 00 | |||||||||||||||||
scalar · Bits · read-write · current This object clears the counters associated with the following protocols - BGP, OSPFv2, RIPv2/ng, OSPFv3, RTMv4/v6, ARP/ND, NETIP(v4/v6) All the bit is set as 1, it clears the specified protocol counters. bgp(1) When this bit is set,clears bgp protocol counters. ospf(2) When this bit is set,clears ospf protocol counters. rip(3) When this bit is set,clears rip protocol counters. rip6(4) When this bit is set,clears rip6 protocol counters. ospf3(5) When this bit is set,clears ospf3 protocol counters. ipv4(6) When this bit is set,clears ipv4 protocol counters. ipv6(7) When this bit is set,clears ipv6 protocol counters.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| NissZtp | 1.3.6.1.4.1.2076.81.18 | ||||||||||||||||||||
| SissZtpConfigStatus | 1.3.6.1.4.1.2076.81.18.1 | INTEGER | RW | ||||||||||||||||||
scalar · INTEGER · read-write · current Object to enable/disable ZTP in the system. The configuration will be updated in iss nvram file. It will take effect only in the next reload
| |||||||||||||||||||||
| SissZtpCurrentStatus | 1.3.6.1.4.1.2076.81.18.2 | INTEGER | RO | ||||||||||||||||||
scalar · INTEGER · read-only · current This object indicates the current status of ZTP operation in the switch.
| |||||||||||||||||||||
| NissRunConfig | 1.3.6.1.4.1.2076.81.19 | ||||||||||||||||||||
| SissRunConfigFileTransferMode | 1.3.6.1.4.1.2076.81.19.1 | INTEGER | RW | ||||||||||||||||||
scalar · INTEGER · read-write · current This object indicates the Transfer mode ,for downloading the configuration file in CLI command format
| |||||||||||||||||||||
| SissRunConfigIpAddrType | 1.3.6.1.4.1.2076.81.19.2 | InetAddressType | RW | ||||||||||||||||||
scalar · InetAddressType · read-write · current This mib object specifies the address type of the remote system from which the running configuration in CLI format has to be downloaded.The address type can be IPv4 or IPv6 unicast address | |||||||||||||||||||||
| SissRunConfigIpAddr | 1.3.6.1.4.1.2076.81.19.3 | InetAddress | RW | ||||||||||||||||||
scalar · InetAddress · read-write · current This mib object indicates the IP Address of the remote system from which the running configuration in CLI format has to be downloaded | |||||||||||||||||||||
| SissRunConfigUserName | 1.3.6.1.4.1.2076.81.19.4 | DisplayString (SIZE (0..20)) | RW | ||||||||||||||||||
scalar · DisplayString (SIZE (0..20)) · read-write · current This mib object indicates the User name required for downloading running-config file in CLI command format. The user name is applicable when transfer mode is sftp. This object is not valid when Transfer Mode is selected as tftp | |||||||||||||||||||||
| SissRunConfigPassword | 1.3.6.1.4.1.2076.81.19.5 | DisplayString (SIZE (0..20)) | RW | ||||||||||||||||||
scalar · DisplayString (SIZE (0..20)) · read-write · current This mib object indicates the Password required for downloading running-config file in CLI command format. This password is applicable when transfer mode is sftp. This object is not valid when Transfer Mode is selected as tftp | |||||||||||||||||||||
| SissRunConfigFileName | 1.3.6.1.4.1.2076.81.19.6 | DisplayString (SIZE (1..128)) | RW | ||||||||||||||||||
scalar · DisplayString (SIZE (1..128)) · read-write · current This mib object indicates the Name of the running-config file to be downloaded from remote server. | |||||||||||||||||||||
| SissApplyConfigToRunningConfig | 1.3.6.1.4.1.2076.81.19.7 | TruthValue | RW | ||||||||||||||||||
scalar · TruthValue · read-write · current When set as 'true' the configuration file in CLI command format is downloaded from remote tftp/sftp server. The configurations are applied on the switch and the value of this object reverts back to 'false'. This object is applicable only when the configuration restore type (issRestoreType) is CSR. This command is recommended to be used only when switch has just come up and no configurations are performed to the switch. When the switch is already running with some configurations, issuing this command may result in errors for the conflicting command. Note: For uploading switch running configuration to remote tftp/sftp server the mib object 'issInitiateRunningConfig' should be used | |||||||||||||||||||||
| SissConfigToRunningConfigStatus | 1.3.6.1.4.1.2076.81.19.8 | INTEGER | RO | ||||||||||||||||||
scalar · INTEGER · read-only · current Status of applying CLI command configuration to the running configuration of the switch
| |||||||||||||||||||||
| SissInitiateRunningConfig | 1.3.6.1.4.1.2076.81.19.9 | TruthValue | RW | ||||||||||||||||||
scalar · TruthValue · read-write · current When set as 'true', the running configurations in the switch will be uploaded to the TFTP/SFTP server. As soon as the running configurations upload operation is completed in the chosen remote system, the value of this object reverts back to 'false'. | |||||||||||||||||||||
| SissCopyStartupConfig | 1.3.6.1.4.1.2076.81.19.10 | TruthValue | RW | ||||||||||||||||||
scalar · TruthValue · read-write · current When set as 'true', the 'startup configuration file' in the switch will be uploaded to the TFTP/SFTP server. As soon as the upload operation is completed in the chosen remote system, the value of this object reverts back to 'false'. The objects such as issRunConfigIpAddr , issRunConfigFileName are used to configure the attributes required for the Copy Startup Config operation. | |||||||||||||||||||||
| SissStartupToRunningConfig | 1.3.6.1.4.1.2076.81.19.11 | TruthValue | RW | ||||||||||||||||||
scalar · TruthValue · read-write · current When set as 'true' the configuration file in CLI command format will be copied from startup-config file to running-config.The configurations are applied on the switch and the value of this object reverts back to 'false'. This object is applicable only when the configuration restore type (issRestoreType) is CSR. This command is recommended to be used only when switch has just come up and no configurations are performed to the switch. When the switch is already running with some configurations, issuing this command may result in errors for the conflicting command. | |||||||||||||||||||||
Textual conventions
PortListOCTET STRINGEach octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'.
Traps / Notifications
- issAuditTrapMessage
1.3.6.1.4.1.2076.81.0.3 - issLogTrapMessage
1.3.6.1.4.1.2076.81.0.10 - issMsrUpdateEventFail
1.3.6.1.4.1.2076.81.0.2 - issTrapCPUThreshold
1.3.6.1.4.1.2076.81.0.5 - issTrapConfigRestore
1.3.6.1.4.1.2076.81.0.1 - issTrapFanStatus
1.3.6.1.4.1.2076.81.0.9 - issTrapFlashUsage
1.3.6.1.4.1.2076.81.0.8 - issTrapPowerSupply
1.3.6.1.4.1.2076.81.0.6 - issTrapRAMUsage
1.3.6.1.4.1.2076.81.0.7 - issTrapTemperature
1.3.6.1.4.1.2076.81.0.4