RPS-SC200-MIB
Swichtec Power Systemssnmptranslate -m RPS-SC200-MIB -Tpsnmpwalk -v2c -c <community> -m RPS-SC200-MIB <host> 1.3.6.1.4.1.1918.2.13.1Imports
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP |
|---|---|
| SNMPv2-SMI | Bits, Counter32, Integer32, IpAddress, MODULE-IDENTITY, MibIdentifier, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, enterprises, iso, mib-2 |
| SNMPv2-TC | DisplayString, PhysAddress, TEXTUAL-CONVENTION |
OID tree
| Name | OID | Type | Access | Status | Example | ||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Neaton-chnz | 1.3.6.1.4.1.1918 | ||||||||||||||||||||
| Ndc-Power-System | 1.3.6.1.4.1.1918.2 | ||||||||||||||||||||
| Nrps-SC200 | 1.3.6.1.4.1.1918.2.13 | ||||||||||||||||||||
| Irps-sc200MibModule | 1.3.6.1.4.1.1918.2.13.1 | ||||||||||||||||||||
| Nrps-Objects | 1.3.6.1.4.1.1918.2.13.10 | ||||||||||||||||||||
| Nsystem-Identity | 1.3.6.1.4.1.1918.2.13.10.10 | ||||||||||||||||||||
| Ssystem-Manufacturer | 1.3.6.1.4.1.1918.2.13.10.10.10 | Display_20 | RW | ||||||||||||||||||
scalar · Display_20 · read-write · current The manufacturer of the DC power system. | |||||||||||||||||||||
| Ssystem-Serial-Number | 1.3.6.1.4.1.1918.2.13.10.10.20 | Display_10 | RW | 315646 | |||||||||||||||||
scalar · Display_10 · read-write · current The DC power system serial number assigned by the manufacturer. Example values from LibreNMS test devices
| |||||||||||||||||||||
| Ssystem-Type | 1.3.6.1.4.1.1918.2.13.10.10.30 | Display_20 | RW | SY106769 | |||||||||||||||||
scalar · Display_20 · read-write · current The DC power system model number assigned by the manufacturer. Example values from LibreNMS test devices
| |||||||||||||||||||||
| Ssystem-Location | 1.3.6.1.4.1.1918.2.13.10.10.40 | Display_20 | RW | ||||||||||||||||||
scalar · Display_20 · read-write · current Usually the location of the DC power system within the site. | |||||||||||||||||||||
| Ssite-Name | 1.3.6.1.4.1.1918.2.13.10.10.50 | Display_40 | RW | ||||||||||||||||||
scalar · Display_40 · read-write · current The site designation or code. | |||||||||||||||||||||
| Ssite-Address | 1.3.6.1.4.1.1918.2.13.10.10.60 | Display_40 | RW | ||||||||||||||||||
scalar · Display_40 · read-write · current The street address of the site. | |||||||||||||||||||||
| Ssite-Notes | 1.3.6.1.4.1.1918.2.13.10.10.70 | Display_253 | RW | ||||||||||||||||||
scalar · Display_253 · read-write · current Notes made by the installation or maintenance personnel. | |||||||||||||||||||||
| Ssystem-Object-ID | 1.3.6.1.4.1.1918.2.13.10.10.80 | MIB_Object_ID_80 | RW | ||||||||||||||||||
scalar · MIB_Object_ID_80 · read-write · current Used to form the return value for the SNMP MIB-2 sysObjectId. These numbers start with a specific enterprise ID (i.e. 1918 for Eaton Christchurch NZ) and are preceded by 1.3.6.1.4.1 to form an object ID for the system type. | |||||||||||||||||||||
| Strap-Format | 1.3.6.1.4.1.1918.2.13.10.10.90 | SNMP_Trap_Format | RW | ||||||||||||||||||
scalar · SNMP_Trap_Format · read-write · current Select Eaton for multiple trap numbers, or X.733 for a single trap number as per ITU X.733. | |||||||||||||||||||||
| Sconfiguration-Name | 1.3.6.1.4.1.1918.2.13.10.10.100 | Display_40 | RW | ||||||||||||||||||
scalar · Display_40 · read-write · current Name of the configuration in the controller database | |||||||||||||||||||||
| Scontact | 1.3.6.1.4.1.1918.2.13.10.10.110 | Display_253 | RW | ||||||||||||||||||
scalar · Display_253 · read-write · current Contact details for the person responsible for this DC power system. | |||||||||||||||||||||
| Sis-Three-Phase-System | 1.3.6.1.4.1.1918.2.13.10.10.120 | Boolean | RO | ||||||||||||||||||
scalar · Boolean · read-only · current Indicates if the system contains three phase rectifiers or single phase rectifiers. | |||||||||||||||||||||
| Ncontroller | 1.3.6.1.4.1.1918.2.13.10.20 | ||||||||||||||||||||
| Smanufacturer-Name | 1.3.6.1.4.1.1918.2.13.10.20.10 | Display_20 | RO | ||||||||||||||||||
scalar · Display_20 · read-only · current The name of the manufacturer. | |||||||||||||||||||||
| Sslave-Type | 1.3.6.1.4.1.1918.2.13.10.20.20 | Slave_Type | RO | ||||||||||||||||||
scalar · Slave_Type · read-only · current Mandatory command identifying the device. | |||||||||||||||||||||
| Ssoftware-Version | 1.3.6.1.4.1.1918.2.13.10.20.30 | Display_10 | RO | 4.04 | |||||||||||||||||
scalar · Display_10 · read-only · current Application software version. This is the software version of the main controller application. Example values from LibreNMS test devices
| |||||||||||||||||||||
| Sldr-Software-Version | 1.3.6.1.4.1.1918.2.13.10.20.50 | Display_10 | RO | ||||||||||||||||||
scalar · Display_10 · read-only · current Bootloader software version. The bootloader is responsible for loading and running the system support software and the main application. The bootloader software can be upgrading using the normal web upgrade process. However, if power fails during a bootloader upgrade then the controller may need to be returned to base for repair. Without a bootloader, no software can run on the controller. | |||||||||||||||||||||
| Sinterface-Version | 1.3.6.1.4.1.1918.2.13.10.20.70 | Unsigned16 | RO | ||||||||||||||||||
scalar · Unsigned16 · read-only · current S3P interface version. As the embedded software is upgraded, the communications interface may change. This number reflects any such change. This value, along with Compatible Interface Version is used by DCTools to determine how to communicate. Third party applications should also check this version and optionally warn the user if it is dealing with an incompatible interface. While Eaton Corporation does attempt to maintain backwards compatibility with its interfaces, this cannot be guaranteed. | |||||||||||||||||||||
| Shardware-Version | 1.3.6.1.4.1.1918.2.13.10.20.80 | Display_10 | RO | 022 | |||||||||||||||||
scalar · Display_10 · read-only · current The Product Hardware Version Example values from LibreNMS test devices
| |||||||||||||||||||||
| Sserial-Number | 1.3.6.1.4.1.1918.2.13.10.20.90 | Display_20 | RO | 246152313 | |||||||||||||||||
scalar · Display_20 · read-only · current The Product Serial Number. This item is not reset by the Reset System Configuration command. Example values from LibreNMS test devices
| |||||||||||||||||||||
| Sethernet-MAC-Address | 1.3.6.1.4.1.1918.2.13.10.20.100 | Display_17 | RO | ||||||||||||||||||
scalar · Display_17 · read-only · current The unique ethernet address of the controller. | |||||||||||||||||||||
| Ncommunications | 1.3.6.1.4.1.1918.2.13.10.30 | ||||||||||||||||||||
| Ss3P-Access | 1.3.6.1.4.1.1918.2.13.10.30.3 | Enable_State | RW | ||||||||||||||||||
scalar · Enable_State · read-write · current Determines whether or not the S3P access is allowed. | |||||||||||||||||||||
| Shttp-Access | 1.3.6.1.4.1.1918.2.13.10.30.6 | Enable_State | RW | ||||||||||||||||||
scalar · Enable_State · read-write · current If Enabled, HTTP Web interface access is allowed. | |||||||||||||||||||||
| Shttps-Access | 1.3.6.1.4.1.1918.2.13.10.30.7 | Enable_State | RW | ||||||||||||||||||
scalar · Enable_State · read-write · current If Enabled, HTTPS (SSL) Web interface access is allowed. | |||||||||||||||||||||
| Ssnmp-Access | 1.3.6.1.4.1.1918.2.13.10.30.8 | SNMP_Access_State | RW | ||||||||||||||||||
scalar · SNMP_Access_State · read-write · current Determines how SNMP access is allowed. | |||||||||||||||||||||
| Sserial-Server-Access | 1.3.6.1.4.1.1918.2.13.10.30.9 | Enable_State | RW | ||||||||||||||||||
scalar · Enable_State · read-write · current Enables operation of pass-through from TCP to the serial port. | |||||||||||||||||||||
| Ss3P-Address | 1.3.6.1.4.1.1918.2.13.10.30.10 | Unsigned16 | RW | ||||||||||||||||||
scalar · Unsigned16 · read-write · current If the controller is connected to a serial S3P bus that supports multiple devices, this address is used to distinguish the devices. Otherwise it should remain at 1. | |||||||||||||||||||||
| Sip-Address | 1.3.6.1.4.1.1918.2.13.10.30.20 | IpAddress | RW | ||||||||||||||||||
scalar · IpAddress · read-write · current The Internet Protocol (IP) address. This value and the Subnet Mask must be set correctly to communicate using Ethernet. Consult your network administrator. | |||||||||||||||||||||
| Ssubnet-Mask | 1.3.6.1.4.1.1918.2.13.10.30.30 | IpAddress | RW | ||||||||||||||||||
scalar · IpAddress · read-write · current Identifies which fragment of the IP address is the sub-network identity. This value and the IP Address must be set correctly to communicate using Ethernet. Consult your network administrator. | |||||||||||||||||||||
| Sgateway-Address | 1.3.6.1.4.1.1918.2.13.10.30.50 | IpAddress | RW | ||||||||||||||||||
scalar · IpAddress · read-write · current Allows access to IP addresses outside your sub-network. Consult your network administrator. | |||||||||||||||||||||
| Nserial | 1.3.6.1.4.1.1918.2.13.10.30.53 | ||||||||||||||||||||
| Nport-Settings | 1.3.6.1.4.1.1918.2.13.10.30.53.5 | ||||||||||||||||||||
| Sbaud-Rate | 1.3.6.1.4.1.1918.2.13.10.30.53.5.10 | Baud_Rate | RW | ||||||||||||||||||
scalar · Baud_Rate · read-write · current Transmission speed of the serial port. | |||||||||||||||||||||
| Sparity | 1.3.6.1.4.1.1918.2.13.10.30.53.5.20 | Parity | RW | ||||||||||||||||||
scalar · Parity · read-write · current The parity error detect mode. | |||||||||||||||||||||
| Sstop-Bits | 1.3.6.1.4.1.1918.2.13.10.30.53.5.30 | Stop_Bits | RW | ||||||||||||||||||
scalar · Stop_Bits · read-write · current The number of stop bits. | |||||||||||||||||||||
| Senable-Modem | 1.3.6.1.4.1.1918.2.13.10.30.53.10 | Enable_State | RW | ||||||||||||||||||
scalar · Enable_State · read-write · current Determines whether or not the RS232 port is configured to work with a modem. | |||||||||||||||||||||
| Salarm-Report | 1.3.6.1.4.1.1918.2.13.10.30.53.20 | Alarm_Report | RW | ||||||||||||||||||
scalar · Alarm_Report · read-write · current This indicates that the dial-out process will start when an alarm occurs. | |||||||||||||||||||||
| Smodem-Set-Up-String | 1.3.6.1.4.1.1918.2.13.10.30.53.30 | Display_30 | RW | ||||||||||||||||||
scalar · Display_30 · read-write · current The string sent to the modem on reset. The modem AT command should not be included as it is automatically sent. The Auto-Answer Rings parameter is also sent, so it does not need to be included here. For complete details of appropriate commands, consult your modem documentation. | |||||||||||||||||||||
| Smodem-Auto-Answer-Rings | 1.3.6.1.4.1.1918.2.13.10.30.53.40 | Unsigned8 | RW | ||||||||||||||||||
scalar · Unsigned8 · read-write · current Number of rings before an incoming call is answered. Setting this parameter to zero disables incoming calls (the modem can still be used for alarm reporting). | |||||||||||||||||||||
| Smodem-Maximum-Retries | 1.3.6.1.4.1.1918.2.13.10.30.53.50 | Unsigned8 | RW | ||||||||||||||||||
scalar · Unsigned8 · read-write · current If an alarm report dial-out does not connect with a remote modem, then this number of subsequent alarm report attempts will be made on the current dial-out number before trying the next dial-out number from the Dial Out Number Table. Dialing will stop if none of the numbers in the Dial Out Number Table connect. | |||||||||||||||||||||
| Smodem-Retry-Interval | 1.3.6.1.4.1.1918.2.13.10.30.53.60 | TimeIntervalInSeconds | RW | ||||||||||||||||||
scalar · TimeIntervalInSeconds · read-write · current If an alarm report dial-out does not connect with a remote modem, then another attempt will be made after this time interval.
| |||||||||||||||||||||
| Smodem-Power-Reset | 1.3.6.1.4.1.1918.2.13.10.30.53.70 | Enable_State | RW | ||||||||||||||||||
scalar · Enable_State · read-write · current If this is enabled, then an attempt will be made to reset a non-operating modem by turning its power supply off and on using digital output 2. | |||||||||||||||||||||
| Tdial-Out-Number-Table | 1.3.6.1.4.1.1918.2.13.10.30.53.80 | NA | |||||||||||||||||||
| Rdial-Out-Number-Entry | 1.3.6.1.4.1.1918.2.13.10.30.53.80.1 | NA | |||||||||||||||||||
row · not-accessible · current | |||||||||||||||||||||
| Cdial-Out-Number-Index | 1.3.6.1.4.1.1918.2.13.10.30.53.80.1.1 | Unsigned8 | RO | ||||||||||||||||||
column · Unsigned8 · read-only · current Automatically generated index object. | |||||||||||||||||||||
| Cdial-Out-Number | 1.3.6.1.4.1.1918.2.13.10.30.53.80.1.10 | Display_30 | RW | ||||||||||||||||||
column · Display_30 · read-write · current The telephone numbers to be called (via a modem) if alarm reporting is enabled. Consult the modem documentation for appropriate dial modifiers to use with the ATD command. Leave blank to prevent dial-out. | |||||||||||||||||||||
| Tsms-Notification-Table | 1.3.6.1.4.1.1918.2.13.10.30.53.90 | NA | |||||||||||||||||||
| Rsms-Notification-Entry | 1.3.6.1.4.1.1918.2.13.10.30.53.90.1 | NA | |||||||||||||||||||
row · not-accessible · current | |||||||||||||||||||||
| Csms-Notification-Index | 1.3.6.1.4.1.1918.2.13.10.30.53.90.1.1 | Unsigned8 | RO | ||||||||||||||||||
column · Unsigned8 · read-only · current Automatically generated index object. | |||||||||||||||||||||
| Csms-Phone-Name | 1.3.6.1.4.1.1918.2.13.10.30.53.90.1.10 | Display_20 | RW | ||||||||||||||||||
column · Display_20 · read-write · current A name to identify this phone. | |||||||||||||||||||||
| Csms-Level | 1.3.6.1.4.1.1918.2.13.10.30.53.90.1.20 | Severity_Level | RW | ||||||||||||||||||
column · Severity_Level · read-write · current Sets the severity of alarms to be reported to this SMS receiver. | |||||||||||||||||||||
| Csms-Phone-Number | 1.3.6.1.4.1.1918.2.13.10.30.53.90.1.30 | Display_30 | RW | ||||||||||||||||||
column · Display_30 · read-write · current The phone number for SMS notifications. | |||||||||||||||||||||
| Csms-Prefix | 1.3.6.1.4.1.1918.2.13.10.30.53.90.1.40 | Display_60 | RW | ||||||||||||||||||
column · Display_60 · read-write · current This string is prepended to every SMS sent to this number, excluding responses to SMS commands. | |||||||||||||||||||||
| Nmodbus | 1.3.6.1.4.1.1918.2.13.10.30.57 | ||||||||||||||||||||
| Smodbus-Access | 1.3.6.1.4.1.1918.2.13.10.30.57.10 | Enable_State | RW | ||||||||||||||||||
scalar · Enable_State · read-write · current Determines whether or not Modbus/TCP and Modbus/RTU access is allowed. | |||||||||||||||||||||
| Smodbus-Address | 1.3.6.1.4.1.1918.2.13.10.30.57.20 | Unsigned8 | RW | ||||||||||||||||||
scalar · Unsigned8 · read-write · current The devices address for the Modbus/RTU protocol. | |||||||||||||||||||||
| Smodbus-Interface-Version | 1.3.6.1.4.1.1918.2.13.10.30.57.30 | Unsigned16 | RO | ||||||||||||||||||
scalar · Unsigned16 · read-only · current As the embedded software is upgraded, the Modbus register mappings may change. This number reflects any such change. | |||||||||||||||||||||
| Nsnmp-Settings | 1.3.6.1.4.1.1918.2.13.10.30.60 | ||||||||||||||||||||
| Ssnmp-Read-Community | 1.3.6.1.4.1.1918.2.13.10.30.60.10 | Display_32 | RW | ||||||||||||||||||
scalar · Display_32 · read-write · current Community that can get items. | |||||||||||||||||||||
| Ssnmp-Write-Community | 1.3.6.1.4.1.1918.2.13.10.30.60.20 | Display_32 | RW | ||||||||||||||||||
scalar · Display_32 · read-write · current Community that can set items. | |||||||||||||||||||||
| Senable-Trap-Repeat | 1.3.6.1.4.1.1918.2.13.10.30.60.30 | Enable_State | RW | ||||||||||||||||||
scalar · Enable_State · read-write · current If enabled, alarm activation traps will be repeated according to Trap Repeat Rate. | |||||||||||||||||||||
| Strap-Repeat-Rate | 1.3.6.1.4.1.1918.2.13.10.30.60.40 | TimeIntervalInMinutes | RW | ||||||||||||||||||
scalar · TimeIntervalInMinutes · read-write · current How often to send a trap to trap receivers if Enable Trap Repeat is Enabled or the trap receiver's Trap Receiver Mode is Acknowledged Summary Trap.
| |||||||||||||||||||||
| Strap-Version | 1.3.6.1.4.1.1918.2.13.10.30.60.45 | SNMP_Trap_Version | RW | ||||||||||||||||||
scalar · SNMP_Trap_Version · read-write · current Indicates which version of the SNMP protocol will be used to send traps. | |||||||||||||||||||||
| Tsnmp-Trap-Receiver-Table | 1.3.6.1.4.1.1918.2.13.10.30.60.50 | NA | |||||||||||||||||||
| Rsnmp-Trap-Receiver-Entry | 1.3.6.1.4.1.1918.2.13.10.30.60.50.1 | NA | |||||||||||||||||||
row · not-accessible · current | |||||||||||||||||||||
| Csnmp-Trap-Receiver-Index | 1.3.6.1.4.1.1918.2.13.10.30.60.50.1.1 | Unsigned8 | RO | ||||||||||||||||||
column · Unsigned8 · read-only · current Automatically generated index object. | |||||||||||||||||||||
| Ctrap-Receiver-IP-Address | 1.3.6.1.4.1.1918.2.13.10.30.60.50.1.20 | IpAddress | RW | ||||||||||||||||||
column · IpAddress · read-write · current SNMP notifications of events are sent to this IP address. | |||||||||||||||||||||
| Ctrap-Receiver-Port | 1.3.6.1.4.1.1918.2.13.10.30.60.50.1.30 | Unsigned16 | RW | ||||||||||||||||||
column · Unsigned16 · read-write · current SNMP notifications of events are sent to this UDP port. | |||||||||||||||||||||
| Ctrap-Receiver-Name | 1.3.6.1.4.1.1918.2.13.10.30.60.50.1.40 | Display_20 | RW | ||||||||||||||||||
column · Display_20 · read-write · current Name used to identify the receiver. | |||||||||||||||||||||
| Ctrap-Receiver-Level | 1.3.6.1.4.1.1918.2.13.10.30.60.50.1.50 | Severity_Level | RW | ||||||||||||||||||
column · Severity_Level · read-write · current Sets the severity of alarms to be reported to this trap receiver. | |||||||||||||||||||||
| Ctrap-Receiver-Community | 1.3.6.1.4.1.1918.2.13.10.30.60.50.1.60 | Display_32 | RW | ||||||||||||||||||
column · Display_32 · read-write · current Community to use for traps sent to the receiver. | |||||||||||||||||||||
| Ctrap-Receiver-Mode | 1.3.6.1.4.1.1918.2.13.10.30.60.50.1.70 | Trap_Receiver_Mode | RW | ||||||||||||||||||
column · Trap_Receiver_Mode · read-write · current Set to Normal traps to send normal traps to a Network Management System on alarm activation and deactivation. Set to Acknowledged Summary Traps to send summary traps to PowerManagerII. These traps are repeated until PowerManagerII receives the trap, connects to the controller, and downloads alarms and data. | |||||||||||||||||||||
| Cacknowledge-Alarm-Summary-Trap | 1.3.6.1.4.1.1918.2.13.10.30.60.50.1.80 | No_Data | RW | ||||||||||||||||||
column · No_Data · read-write · current This command will acknowledge reception of the alarm summary trap. | |||||||||||||||||||||
| SsnmPv3-User-Name | 1.3.6.1.4.1.1918.2.13.10.30.60.55 | Display_40 | RW | ||||||||||||||||||
scalar · Display_40 · read-write · current The user name used in the SNMPv3 security model. | |||||||||||||||||||||
| SsnmPv3-SHA-Password | 1.3.6.1.4.1.1918.2.13.10.30.60.60 | Display_64 | RW | ||||||||||||||||||
scalar · Display_64 · read-write · current SNMP V3 password for the authentication protocol (SHA). If set to empty, SNMP v3 will use neither authentication nor encryption. | |||||||||||||||||||||
| SsnmPv3-DES-Password | 1.3.6.1.4.1.1918.2.13.10.30.60.70 | Display_64 | RW | ||||||||||||||||||
scalar · Display_64 · read-write · current SNMP V3 password for the privacy protocol (DES). Only used if authentication password is also set. If set to empty, SNMP v3 will not use encryption. | |||||||||||||||||||||
| Nemail | 1.3.6.1.4.1.1918.2.13.10.30.65 | ||||||||||||||||||||
| Semail-Notifications | 1.3.6.1.4.1.1918.2.13.10.30.65.10 | Enable_State | RW | ||||||||||||||||||
scalar · Enable_State · read-write · current Determines whether or not the controller will send alarm and event notifications via email. | |||||||||||||||||||||
| Ssmtp-Server-IP-Address | 1.3.6.1.4.1.1918.2.13.10.30.65.20 | IpAddress | RW | ||||||||||||||||||
scalar · IpAddress · read-write · current SMTP notifications of events will be sent using this SMTP server. | |||||||||||||||||||||
| Ssmtp-Server-Port | 1.3.6.1.4.1.1918.2.13.10.30.65.30 | Unsigned16 | RW | ||||||||||||||||||
scalar · Unsigned16 · read-write · current SMTP notifications of events will be sent using this SMTP server. | |||||||||||||||||||||
| Semail-Return-Address | 1.3.6.1.4.1.1918.2.13.10.30.65.40 | Display_200 | RW | ||||||||||||||||||
scalar · Display_200 · read-write · current The email return address. If not empty, the controller will arrange to have any delivery failure notifications sent to this address. | |||||||||||||||||||||
| Semail-Subject-Prefix | 1.3.6.1.4.1.1918.2.13.10.30.65.50 | Display_20 | RW | ||||||||||||||||||
scalar · Display_20 · read-write · current The generated email subject will be prefixed with this string to allow automatic processing of the email. | |||||||||||||||||||||
| Temail-Receiver-Table | 1.3.6.1.4.1.1918.2.13.10.30.65.60 | NA | |||||||||||||||||||
| Remail-Receiver-Entry | 1.3.6.1.4.1.1918.2.13.10.30.65.60.1 | NA | |||||||||||||||||||
row · not-accessible · current
| |||||||||||||||||||||
| Cemail-Receiver-Index | 1.3.6.1.4.1.1918.2.13.10.30.65.60.1.1 | Unsigned8 | RO | ||||||||||||||||||
column · Unsigned8 · read-only · current Automatically generated index object. | |||||||||||||||||||||
| Cemail-Receiver-Address | 1.3.6.1.4.1.1918.2.13.10.30.65.60.1.10 | Display_200 | RW | ||||||||||||||||||
column · Display_200 · read-write · current The receiver's email address. | |||||||||||||||||||||
| Cemail-Receiver-Level | 1.3.6.1.4.1.1918.2.13.10.30.65.60.1.20 | Severity_Level | RW | ||||||||||||||||||
column · Severity_Level · read-write · current Sets the severity of alarms to be reported to this email receiver. | |||||||||||||||||||||
| Cemail-Receiver-Delay | 1.3.6.1.4.1.1918.2.13.10.30.65.60.1.30 | TimeIntervalInSeconds | RW | ||||||||||||||||||
column · TimeIntervalInSeconds · read-write · current The controller will delay sending an email by this amount of time and collate all events that occur during this time.
| |||||||||||||||||||||
| Csend-Test-Email | 1.3.6.1.4.1.1918.2.13.10.30.65.60.1.40 | No_Data | RW | ||||||||||||||||||
column · No_Data · read-write · current This will send an email notification to the receiver. | |||||||||||||||||||||
| Csmtp-Result | 1.3.6.1.4.1.1918.2.13.10.30.65.60.1.50 | Unsigned16 | RO | ||||||||||||||||||
column · Unsigned16 · read-only · current Result of the last SMTP operation affecting this receiver. SMTP results are usually three-digit numbers with the first digit indicating success or failure severity. (2 = Ok, 4 = Temporary Failure, 5 = Permanent Failure) In addition the controller will set the code 9999 if communications to the SMTP server failed. | |||||||||||||||||||||
| Nsntp | 1.3.6.1.4.1.1918.2.13.10.30.70 | ||||||||||||||||||||
| Spoll-Interval | 1.3.6.1.4.1.1918.2.13.10.30.70.10 | TimeIntervalInSeconds | RW | ||||||||||||||||||
scalar · TimeIntervalInSeconds · read-write · current Polling interval in seconds. If set 0, the controller will listen to broadcasts from an NTP server on the local network and set its time accordingly; otherwise it will try to contact the primary and secondary (S)NTP server regularly according to the configured value.
| |||||||||||||||||||||
| Sudp-Port | 1.3.6.1.4.1.1918.2.13.10.30.70.20 | Unsigned16 | RW | ||||||||||||||||||
scalar · Unsigned16 · read-write · current UDP port of SNTP server. | |||||||||||||||||||||
| Sprimary-Address | 1.3.6.1.4.1.1918.2.13.10.30.70.30 | IpAddress | RW | ||||||||||||||||||
scalar · IpAddress · read-write · current IP address of primary SNTP server. | |||||||||||||||||||||
| Sbackup-Address | 1.3.6.1.4.1.1918.2.13.10.30.70.40 | IpAddress | RW | ||||||||||||||||||
scalar · IpAddress · read-write · current IP address of backup SNTP server. | |||||||||||||||||||||
| Ssntp-Last-Update | 1.3.6.1.4.1.1918.2.13.10.30.70.50 | Julian_Time_UTC_25 | RO | ||||||||||||||||||
scalar · Julian_Time_UTC_25 · read-only · current The time when the last SNTP update occurred. | |||||||||||||||||||||
| Tweb-User-Table | 1.3.6.1.4.1.1918.2.13.10.30.80 | NA | |||||||||||||||||||
| Rweb-User-Entry | 1.3.6.1.4.1.1918.2.13.10.30.80.1 | NA | |||||||||||||||||||
row · not-accessible · current
| |||||||||||||||||||||
| Cweb-User-Index | 1.3.6.1.4.1.1918.2.13.10.30.80.1.1 | Unsigned8 | RO | ||||||||||||||||||
column · Unsigned8 · read-only · current Automatically generated index object. | |||||||||||||||||||||
| Cuser-Name | 1.3.6.1.4.1.1918.2.13.10.30.80.1.10 | Display_40 | RW | ||||||||||||||||||
column · Display_40 · read-write · current The full name of the user. This is for reference only and is not used in the login process. | |||||||||||||||||||||
| Cuser-Logon-ID | 1.3.6.1.4.1.1918.2.13.10.30.80.1.21 | Display_20 | RW | ||||||||||||||||||
column · Display_20 · read-write · current The logon name of a user. | |||||||||||||||||||||
| Cuser-Logon-Password | 1.3.6.1.4.1.1918.2.13.10.30.80.1.31 | Display_32 | RW | ||||||||||||||||||
column · Display_32 · read-write · current The password for this user. | |||||||||||||||||||||
| Cuser-Active | 1.3.6.1.4.1.1918.2.13.10.30.80.1.40 | Boolean | RW | ||||||||||||||||||
column · Boolean · read-write · current Indicates whether this user is enabled or disabled. | |||||||||||||||||||||
| Cuser-Read | 1.3.6.1.4.1.1918.2.13.10.30.80.1.50 | Boolean | RW | ||||||||||||||||||
column · Boolean · read-write · current If checked the user is allowed to read the system information and values. | |||||||||||||||||||||
| Cuser-Write | 1.3.6.1.4.1.1918.2.13.10.30.80.1.60 | Boolean | RW | ||||||||||||||||||
column · Boolean · read-write · current If checked the user is allowed to modify configurable values. | |||||||||||||||||||||
| Cuser-Restore | 1.3.6.1.4.1.1918.2.13.10.30.80.1.70 | Boolean | RW | ||||||||||||||||||
column · Boolean · read-write · current If checked the user is allowed to upload configurations or snapshots. | |||||||||||||||||||||
| Cuser-Backup | 1.3.6.1.4.1.1918.2.13.10.30.80.1.80 | Boolean | RW | ||||||||||||||||||
column · Boolean · read-write · current If checked the user is allowed to download configurations or snapshots. | |||||||||||||||||||||
| Cuser-Execute | 1.3.6.1.4.1.1918.2.13.10.30.80.1.90 | Boolean | RW | ||||||||||||||||||
column · Boolean · read-write · current If checked the user is allowed to execute commands. | |||||||||||||||||||||
| Cuser-Upgrade-Firmware | 1.3.6.1.4.1.1918.2.13.10.30.80.1.100 | Boolean | RW | ||||||||||||||||||
column · Boolean · read-write · current If checked the user is allowed to upgrade firmware (including de-installing optional modules). | |||||||||||||||||||||
| Cuser-Edit-User-List | 1.3.6.1.4.1.1918.2.13.10.30.80.1.110 | Boolean | RW | ||||||||||||||||||
column · Boolean · read-write · current If checked the user can edit this table and other security settings. | |||||||||||||||||||||
| Naccess-Control | 1.3.6.1.4.1.1918.2.13.10.33 | ||||||||||||||||||||
| Sui-Access | 1.3.6.1.4.1.1918.2.13.10.33.10 | Access_Protection | RW | ||||||||||||||||||
scalar · Access_Protection · read-write · current Controls keypad access to change configuration items, and start or stop processes. This provides protection against unauthorized or accidental modifications of configuration settings. | |||||||||||||||||||||
| Ss3P-Write-Access-Password | 1.3.6.1.4.1.1918.2.13.10.33.20 | Display_32 | RW | ||||||||||||||||||
scalar · Display_32 · read-write · current If set, S3P requires a password to be used before write access is granted. This password may be used to control remote configuration change or control actions. Note that the password is sent unencrypted. | |||||||||||||||||||||
| Sremote-Access-Level | 1.3.6.1.4.1.1918.2.13.10.33.30 | Access_Level | RO | ||||||||||||||||||
scalar · Access_Level · read-only · current Shows the level of access granted to remote applications. Remote write access to the configuration and control processes is controlled through the S3P Write Access Password. If set, then it must be used to login using the Remote Access Login before database items may be written. | |||||||||||||||||||||
| Nac-input | 1.3.6.1.4.1.1918.2.13.10.40 | ||||||||||||||||||||
| Sac-Voltage | 1.3.6.1.4.1.1918.2.13.10.40.10 | Float | RO | 245 | |||||||||||||||||
scalar · Float · read-only · current The average of the AC voltage measured by all rectifiers.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| Sphase-1 | 1.3.6.1.4.1.1918.2.13.10.40.20 | Float | RO | ||||||||||||||||||
scalar · Float · read-only · current The average of all CR-48 phase-1 input voltages.
| |||||||||||||||||||||
| Sphase-2 | 1.3.6.1.4.1.1918.2.13.10.40.30 | Float | RO | ||||||||||||||||||
scalar · Float · read-only · current The average of all CR-48 phase-2 input voltages.
| |||||||||||||||||||||
| Sphase-3 | 1.3.6.1.4.1.1918.2.13.10.40.40 | Float | RO | ||||||||||||||||||
scalar · Float · read-only · current The average of all CR-48 phase-3 input voltages.
| |||||||||||||||||||||
| Ndc-output | 1.3.6.1.4.1.1918.2.13.10.50 | ||||||||||||||||||||
| Sload-Current | 1.3.6.1.4.1.1918.2.13.10.50.10 | Float | RO | 17 | |||||||||||||||||
scalar · Float · read-only · current The total current drawn by all loads. This value may be measured by the load current shunt(s) if present or calculated from the other system currents.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| Ssystem-Power | 1.3.6.1.4.1.1918.2.13.10.50.20 | Percentile8NAN | RO | 15 | |||||||||||||||||
scalar · Percentile8NAN · read-only · current The output power of the system as a percentage of the total nominal power of the registered rectifiers.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| Sload-Power | 1.3.6.1.4.1.1918.2.13.10.50.30 | Float | RO | 93 | |||||||||||||||||
scalar · Float · read-only · current The power being supplied to the load.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| Nrectifiers | 1.3.6.1.4.1.1918.2.13.10.60 | ||||||||||||||||||||
| Snumber-Of-Registered-Rectifiers | 1.3.6.1.4.1.1918.2.13.10.60.10 | Unsigned8 | RO | ||||||||||||||||||
scalar · Unsigned8 · read-only · current The number of registered rectifiers. | |||||||||||||||||||||
| Snumber-Of-Rectifiers-Failed | 1.3.6.1.4.1.1918.2.13.10.60.13 | Unsigned8 | RO | ||||||||||||||||||
scalar · Unsigned8 · read-only · current Number of rectifiers that must be replaced or require maintenance. | |||||||||||||||||||||
| Snumber-Of-Rectifiers-Comms-Lost | 1.3.6.1.4.1.1918.2.13.10.60.17 | Unsigned8 | RO | ||||||||||||||||||
scalar · Unsigned8 · read-only · current Number of rectifiers that the controller can no longer communicate with. They could have been removed from the system or they could have failed. | |||||||||||||||||||||
| Srectifier-Current | 1.3.6.1.4.1.1918.2.13.10.60.20 | Float | RO | ||||||||||||||||||
scalar · Float · read-only · current The total current output by all rectifiers. This value may be measured by the rectifier current shunt(s) if present, calculated from the other system currents or determined from the rectifier reported currents.
| |||||||||||||||||||||
| Srectifier-Current-Limit | 1.3.6.1.4.1.1918.2.13.10.60.23 | Unsigned8 | RW | ||||||||||||||||||
scalar · Unsigned8 · read-write · current The output current limit of the rectifier. If set to zero then the output current is maximum.
| |||||||||||||||||||||
| Senable-Current-Share | 1.3.6.1.4.1.1918.2.13.10.60.26 | Enable_State | RW | ||||||||||||||||||
scalar · Enable_State · read-write · current When enabled, the rectifier output voltages are adjusted to even (approximately) their output currents. Disable this function if different rectifiers are supplying independent loads. This function should normally be enabled. | |||||||||||||||||||||
| Shighest-Rectifier-Heatsink-Temperature | 1.3.6.1.4.1.1918.2.13.10.60.29 | Float | RO | 37 | |||||||||||||||||
scalar · Float · read-only · current The highest heatsink temperature of all registered rectifiers.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| Trectifier-Values-Table | 1.3.6.1.4.1.1918.2.13.10.60.30 | NA | |||||||||||||||||||
| Rrectifier-Values-Entry | 1.3.6.1.4.1.1918.2.13.10.60.30.1 | NA | |||||||||||||||||||
row · not-accessible · current | |||||||||||||||||||||
| Crectifier-Values-Index | 1.3.6.1.4.1.1918.2.13.10.60.30.1.1 | Unsigned8 | RO | 1 | |||||||||||||||||
column · Unsigned8 · read-only · current Automatically generated index object. Example values from LibreNMS test devices
| |||||||||||||||||||||
| Crectifier-Serial-Number | 1.3.6.1.4.1.1918.2.13.10.60.30.1.30 | Counter32 | RO | 246339625 | |||||||||||||||||
column · Counter32 · read-only · current Rectifier serial number. Example values from LibreNMS test devices
| |||||||||||||||||||||
| Crectifier-Status | 1.3.6.1.4.1.1918.2.13.10.60.30.1.60 | Unsigned8 | RO | 0 | |||||||||||||||||
column · Unsigned8 · read-only · current The status reported by this rectifier. This value cannot be interpreted without knowing the meaning of the various status bits. This is documented in the RXP command set for rectifiers. Example values from LibreNMS test devices
| |||||||||||||||||||||
| Crectifier-Maximum-Current-Limit | 1.3.6.1.4.1.1918.2.13.10.60.30.1.70 | Unsigned8 | RO | 42 | |||||||||||||||||
column · Unsigned8 · read-only · current The current limit value of the rectifier. Adjust Rectifier Current Limit to set a lower operating current limit.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| Crectifier-Maximum-Power-Limit | 1.3.6.1.4.1.1918.2.13.10.60.30.1.80 | DC_Power | RO | 2000 | |||||||||||||||||
column · DC_Power · read-only · current The maximum output power limit value of the rectifier. Adjust Rectifier Current Limit to set a lower operating power limit.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| Crectifier-Minimum-OVSD-Set-Point | 1.3.6.1.4.1.1918.2.13.10.60.30.1.83 | Float | RO | 5720 | |||||||||||||||||
column · Float · read-only · current The minimum OVSD set point that the rectifier accepts.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| Crectifier-Maximum-OVSD-Set-Point | 1.3.6.1.4.1.1918.2.13.10.60.30.1.86 | Float | RO | 5970 | |||||||||||||||||
column · Float · read-only · current The maximum OVSD set point that the rectifier accepts.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| Crectifier-Reported-AC-Voltage | 1.3.6.1.4.1.1918.2.13.10.60.30.1.90 | Float | RO | 245 | |||||||||||||||||
column · Float · read-only · current The AC voltage measured by the rectifier.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| Crectifier-Reported-Voltage | 1.3.6.1.4.1.1918.2.13.10.60.30.1.95 | Float | RO | 5483 | |||||||||||||||||
column · Float · read-only · current The output voltage measured by this rectifier. This is measured by the rectifier and reported via the RXP bus.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| Crectifier-Reported-Current | 1.3.6.1.4.1.1918.2.13.10.60.30.1.100 | Float | RO | 6 | |||||||||||||||||
column · Float · read-only · current The current produced by this rectifier. This is measured by the rectifier and reported via the rectifier comms bus.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| Crectifier-Output-Power | 1.3.6.1.4.1.1918.2.13.10.60.30.1.105 | Float | RO | 158 | |||||||||||||||||
column · Float · read-only · current The current rectifier output power as a percentage of the power limit under the current operating conditions.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| Crectifier-Heatsink-Temperature | 1.3.6.1.4.1.1918.2.13.10.60.30.1.110 | Float | RO | 37 | |||||||||||||||||
column · Float · read-only · current The measured rectifier heatsink temperature.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| Crectifier-Registration-State | 1.3.6.1.4.1.1918.2.13.10.60.30.1.120 | RCP_Slave_State | RO | 2 | |||||||||||||||||
column · RCP_Slave_State · read-only · current Registration state of this rectifier. Example values from LibreNMS test devices
| |||||||||||||||||||||
| Crectifier-Failed-State | 1.3.6.1.4.1.1918.2.13.10.60.30.1.130 | Rect_Fail_State | RO | 0 | |||||||||||||||||
column · Rect_Fail_State · read-only · current A rectifier's failed state. Example values from LibreNMS test devices
| |||||||||||||||||||||
| Cload-Based-Run-Time | 1.3.6.1.4.1.1918.2.13.10.60.30.1.140 | TimeIntervalInSeconds | RO | 4832400 (0d 13h 25m 24s) | |||||||||||||||||
column · TimeIntervalInSeconds · read-only · current The time the rectifier has been operating since it was registered.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| Cshutdown-Rectifier | 1.3.6.1.4.1.1918.2.13.10.60.30.1.150 | Boolean | RW | 0 | |||||||||||||||||
column · Boolean · read-write · current Shuts down the rectifier or restarts it. Use Rectifier Has Been Shutdown to see whether the command has been sent to the rectifier since it can take some seconds. Example values from LibreNMS test devices
| |||||||||||||||||||||
| Crectifier-Has-Been-Shutdown | 1.3.6.1.4.1.1918.2.13.10.60.30.1.160 | Boolean | RO | 0 | |||||||||||||||||
column · Boolean · read-only · current Indicates if the rectifier shutdown command has been sent. Once a Shutdown Rectifier command has been issued some time may elapse before the command is sent to the rectifier. Rectifiers that shut themselves down due to some failure condition are excluded. Example values from LibreNMS test devices
| |||||||||||||||||||||
| Crectifier-Phase-1 | 1.3.6.1.4.1.1918.2.13.10.60.30.1.170 | Float | RO | 0 | |||||||||||||||||
column · Float · read-only · current Rectifier's AC voltage measured at the input connection for phase 1.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| Crectifier-Phase-2 | 1.3.6.1.4.1.1918.2.13.10.60.30.1.180 | Float | RO | 0 | |||||||||||||||||
column · Float · read-only · current Rectifier's AC voltage measured at the input connection for phase 2.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| Crectifier-Phase-3 | 1.3.6.1.4.1.1918.2.13.10.60.30.1.190 | Float | RO | 0 | |||||||||||||||||
column · Float · read-only · current Rectifier's AC voltage measured at the input connection for phase 3.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| Srectifier-Shutdown-Mode | 1.3.6.1.4.1.1918.2.13.10.60.55 | Rectifier_Shutdown_Mode | RW | ||||||||||||||||||
scalar · Rectifier_Shutdown_Mode · read-write · current Specifies whether rectifiers may be shutdown and, if so, whether this is through manual intervention or under the autonomy of the controller. | |||||||||||||||||||||
| Srestart-All-Rectifiers | 1.3.6.1.4.1.1918.2.13.10.60.60 | No_Data | RW | ||||||||||||||||||
scalar · No_Data · read-write · current Restarts all rectifiers that were shut down by the user or LBRS. | |||||||||||||||||||||
| Nload-Based-Rectifier-Shutdown-Config | 1.3.6.1.4.1.1918.2.13.10.60.70 | ||||||||||||||||||||
| Srect-Cycle-Low-Threshold | 1.3.6.1.4.1.1918.2.13.10.60.70.20 | Unsigned8 | RW | ||||||||||||||||||
scalar · Unsigned8 · read-write · current Rectifiers will only be shut down by the LBRS process if the load power is below this percentage of total system power.
| |||||||||||||||||||||
| Srect-Cycle-High-Threshold | 1.3.6.1.4.1.1918.2.13.10.60.70.30 | Unsigned8 | RW | ||||||||||||||||||
scalar · Unsigned8 · read-write · current Additional rectifiers will be started by the LBRS process if the load power is above this percentage of total system power.
| |||||||||||||||||||||
| Srect-Cycle-Interval | 1.3.6.1.4.1.1918.2.13.10.60.70.40 | TimeIntervalInMinutes | RW | ||||||||||||||||||
scalar · TimeIntervalInMinutes · read-write · current The time interval in minutes that rectifiers are cycled when the LBRS process is active.
| |||||||||||||||||||||
| Sreset-Run-Times | 1.3.6.1.4.1.1918.2.13.10.60.70.100 | No_Data | RW | ||||||||||||||||||
scalar · No_Data · read-write · current This command attempts to reset the Run Time on each individual rectifier. | |||||||||||||||||||||
| Sramp-Up-Slope | 1.3.6.1.4.1.1918.2.13.10.60.80 | Unsigned8 | RW | ||||||||||||||||||
scalar · Unsigned8 · read-write · current The ramp-up slope of the rectifier, as a percentage of the rectifier rated current.
| |||||||||||||||||||||
| Sovsd-Set-Point | 1.3.6.1.4.1.1918.2.13.10.60.90 | Float | RW | ||||||||||||||||||
scalar · Float · read-write · current Rectifier Over-Voltage Shutdown set point.
| |||||||||||||||||||||
| Srectifier-Start-Up-Delay | 1.3.6.1.4.1.1918.2.13.10.60.110 | TimeIntervalInSeconds | RW | ||||||||||||||||||
scalar · TimeIntervalInSeconds · read-write · current The delay from AC turn-on before the rectifier output turns on. This is in addition to the fixed rectifier hardware charge time.
| |||||||||||||||||||||
| Ncontrol-Functions | 1.3.6.1.4.1.1918.2.13.10.70 | ||||||||||||||||||||
| Scontrol-State | 1.3.6.1.4.1.1918.2.13.10.70.5 | Control_State | RO | ||||||||||||||||||
scalar · Control_State · read-only · current Indicates the state of control process, e.g. Equalize, Fast Charge or Normal. | |||||||||||||||||||||
| Nvoltage-Control | 1.3.6.1.4.1.1918.2.13.10.70.10 | ||||||||||||||||||||
| Sfloat-Voltage | 1.3.6.1.4.1.1918.2.13.10.70.10.10 | Float | RW | ||||||||||||||||||
scalar · Float · read-write · current The voltage required to maintain optimum battery charge (at the nominal ambient temperature). Use the value recommended by the battery manufacturer. The bus voltage may be adjusted above or below this value by Temperature Compensation, Fast Charge, Battery Test, Equalize or Battery Current Limit.
| |||||||||||||||||||||
| Smaximum-System-Voltage | 1.3.6.1.4.1.1918.2.13.10.70.10.15 | Float | RW | ||||||||||||||||||
scalar · Float · read-write · current Many control functions adjust the bus voltage depending on their respective conditions. However, under no circumstances will the controller deliberately exceed this value. A failing rectifier may cause the voltage to raise above this threshold before the rectifier will execute an overvoltage shut down.
| |||||||||||||||||||||
| Sminimum-System-Voltage | 1.3.6.1.4.1.1918.2.13.10.70.10.17 | Float | RW | ||||||||||||||||||
scalar · Float · read-write · current Many control functions adjust the bus voltage depending on their respective conditions. However, under no circumstances will the controller deliberately adjust the bus voltage to below this value.
| |||||||||||||||||||||
| Sbus-Voltage | 1.3.6.1.4.1.1918.2.13.10.70.10.20 | Float | RO | 5481 | |||||||||||||||||
scalar · Float · read-only · current The system bus voltage from the bus voltage sensor. If the bus voltage sensor has failed, the system bus voltage is determined from the rectifier output voltages.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| Starget-Voltage | 1.3.6.1.4.1.1918.2.13.10.70.10.30 | Float | RO | ||||||||||||||||||
scalar · Float · read-only · current The voltage maintained by AVC. AVC will set the Base Voltage to attempt to maintain the bus voltage to this value.
| |||||||||||||||||||||
| Senable-Active-Voltage-Control | 1.3.6.1.4.1.1918.2.13.10.70.10.35 | Enable_State | RW | ||||||||||||||||||
scalar · Enable_State · read-write · current When AVC is enabled the rectifier output voltage is adjusted to maintain the bus voltage at the configured float voltage (plus or minus any adjustments by active control processes) within a predefined dead band. Enable AVC unless there is specific reason to disable. | |||||||||||||||||||||
| Savc-State | 1.3.6.1.4.1.1918.2.13.10.70.10.40 | AVC_State | RO | ||||||||||||||||||
scalar · AVC_State · read-only · current The state of the Active Voltage Control (AVC) process. | |||||||||||||||||||||
| Savc-Offset | 1.3.6.1.4.1.1918.2.13.10.70.10.50 | Float | RO | ||||||||||||||||||
scalar · Float · read-only · current The difference between the Target Voltage and the measured bus voltage.
| |||||||||||||||||||||
| Sbase-Voltage | 1.3.6.1.4.1.1918.2.13.10.70.10.60 | Float | RO | ||||||||||||||||||
scalar · Float · read-only · current The voltage sent to the rectifiers. This is the Target Voltage plus the AVC Offset. This value is periodically broadcast to all rectifiers. Undetected rectifiers will ignore this value.
| |||||||||||||||||||||
| Ntemperature-Compensation | 1.3.6.1.4.1.1918.2.13.10.70.20 | ||||||||||||||||||||
| Senable-Temperature-Compensation | 1.3.6.1.4.1.1918.2.13.10.70.20.5 | Enable_State | RW | ||||||||||||||||||
scalar · Enable_State · read-write · current When enabled, the battery charge voltage is automatically adjusted based on temperature. This is recommended by battery manufacturers to optimize battery life. | |||||||||||||||||||||
| Stemperature-Compensation-Allowed | 1.3.6.1.4.1.1918.2.13.10.70.20.7 | Can_Start | RO | ||||||||||||||||||
scalar · Can_Start · read-only · current Indicates if Temperature Compensation is allowed to start or not. Temperature compensation cannot start if there are no rectifiers with AC power, or if the temperature sensor has failed. | |||||||||||||||||||||
| Stemperature-Compensation-State | 1.3.6.1.4.1.1918.2.13.10.70.20.10 | TC_State | RO | ||||||||||||||||||
scalar · TC_State · read-only · current The state of the Temperature Compensation process. To be active, it must be enabled, and the temperature sensor must be working. | |||||||||||||||||||||
| Stemperature-Compensation-Slope | 1.3.6.1.4.1.1918.2.13.10.70.20.20 | Float | RW | ||||||||||||||||||
scalar · Float · read-write · current Bus voltage adjustment rate. Use the value specified by the battery manufacturer.
| |||||||||||||||||||||
| Stemperature-Compensation-Reference-Temperature | 1.3.6.1.4.1.1918.2.13.10.70.20.30 | Float | RW | ||||||||||||||||||
scalar · Float · read-write · current The temperature where no voltage adjustment is applied. Use the value specified by the battery manufacturer.
| |||||||||||||||||||||
| Stemperature-Compensation-Upper-Limit | 1.3.6.1.4.1.1918.2.13.10.70.20.40 | Float | RW | ||||||||||||||||||
scalar · Float · read-write · current No additional voltage adjustment is made above this temperature.
| |||||||||||||||||||||
| Stemperature-Compensation-Lower-Limit | 1.3.6.1.4.1.1918.2.13.10.70.20.50 | Float | RW | ||||||||||||||||||
scalar · Float · read-write · current No additional voltage adjustment is made below this temperature.
| |||||||||||||||||||||
| Stemperature-Compensation-Offset-Voltage | 1.3.6.1.4.1.1918.2.13.10.70.20.60 | Float | RO | ||||||||||||||||||
scalar · Float · read-only · current The adjustment to the bus voltage being applied due to the Temperature Compensation. Offset is zero when the battery temperature equals the reference temperature.
| |||||||||||||||||||||
| Sreset-Battery-State | 1.3.6.1.4.1.1918.2.13.10.70.25 | No_Data | RW | ||||||||||||||||||
scalar · No_Data · read-write · current This command resets controller battery state information (Amp hours discharged) and reverts all control process states to Inactive. | |||||||||||||||||||||
| Nequalize | 1.3.6.1.4.1.1918.2.13.10.70.30 | ||||||||||||||||||||
| Senable-Equalize | 1.3.6.1.4.1.1918.2.13.10.70.30.5 | Enable_State | RW | ||||||||||||||||||
scalar · Enable_State · read-write · current Applies a controlled overcharge to the battery by raising the charge voltage for a set time. This may be required to ensure all cells are fully charged, remove sulphation, or redistribute the electrolyte in flooded cells. | |||||||||||||||||||||
| Sequalize-Start-Allowed | 1.3.6.1.4.1.1918.2.13.10.70.30.9 | Can_Start | RO | ||||||||||||||||||
scalar · Can_Start · read-only · current Indicates if an Equalize cycle is allowed to start or the reason why not. An Equalize cycle cannot start if there are no rectifiers with AC power. | |||||||||||||||||||||
| Sequalize-State | 1.3.6.1.4.1.1918.2.13.10.70.30.10 | Control_Process_State | RO | ||||||||||||||||||
scalar · Control_Process_State · read-only · current Indicates the state of the Equalize process: Disabled, Inactive or Active. | |||||||||||||||||||||
| Sequalize-Voltage | 1.3.6.1.4.1.1918.2.13.10.70.30.12 | Float | RW | ||||||||||||||||||
scalar · Float · read-write · current The bus voltage maintained during an Equalize cycle. The bus voltage is further adjusted by Temperature Compensation.
| |||||||||||||||||||||
| Sequalize-Offset-Voltage | 1.3.6.1.4.1.1918.2.13.10.70.30.13 | Float | RO | ||||||||||||||||||
scalar · Float · read-only · current The adjustment to the bus voltage being applied due to the Equalize process.
| |||||||||||||||||||||
| Speriodic-Equalize-First-Date-Time | 1.3.6.1.4.1.1918.2.13.10.70.30.15 | Julian_Time_UTC_25 | RO | ||||||||||||||||||
scalar · Julian_Time_UTC_25 · read-only · current The date and time that the first scheduled Equalize will occur. Subsequent Equalize cycles will occur at every Equalize Interval thereafter. | |||||||||||||||||||||
| Sequalize-Interval | 1.3.6.1.4.1.1918.2.13.10.70.30.17 | TimeIntervalInDays | RW | ||||||||||||||||||
scalar · TimeIntervalInDays · read-write · current The time between scheduled Equalize cycles. The interval period begins at the start of an Equalize. Zero disables scheduled Equalizes.
| |||||||||||||||||||||
| Snext-Equalize-Start-Time | 1.3.6.1.4.1.1918.2.13.10.70.30.20 | Julian_Time_UTC_25 | RO | ||||||||||||||||||
scalar · Julian_Time_UTC_25 · read-only · current The start time of the next scheduled Equalize cycle. The value is NaN if Equalize is active or Periodic Equalize function is disabled. | |||||||||||||||||||||
| Sequalize-Duration | 1.3.6.1.4.1.1918.2.13.10.70.30.30 | TimeIntervalInMinutes | RW | ||||||||||||||||||
scalar · TimeIntervalInMinutes · read-write · current The duration of a scheduled Equalize.
| |||||||||||||||||||||
| Sequalize-Remaining-Time | 1.3.6.1.4.1.1918.2.13.10.70.30.40 | TimeIntervalInSeconds | RO | ||||||||||||||||||
scalar · TimeIntervalInSeconds · read-only · current The time until the current Equalize cycle will stop. The value is NaN if the Equalize is inactive.
| |||||||||||||||||||||
| Sstart-Equalize | 1.3.6.1.4.1.1918.2.13.10.70.30.100 | No_Data | RW | ||||||||||||||||||
scalar · No_Data · read-write · current This command attempts to start the Equalize process. | |||||||||||||||||||||
| Sstop-Equalize | 1.3.6.1.4.1.1918.2.13.10.70.30.110 | No_Data | RW | ||||||||||||||||||
scalar · No_Data · read-write · current This command stops the Equalize process if it is currently active. | |||||||||||||||||||||
| Sequalize-Smart-Alarm | 1.3.6.1.4.1.1918.2.13.10.70.30.120 | Unsigned8 | RW | ||||||||||||||||||
scalar · Unsigned8 · read-write · current The smart alarm that will attempt to start and stop Equalize. To disable set to 0. | |||||||||||||||||||||
| Nfast-Charge | 1.3.6.1.4.1.1918.2.13.10.70.40 | ||||||||||||||||||||
| Senable-Fast-Charge | 1.3.6.1.4.1.1918.2.13.10.70.40.5 | Enable_State | RW | ||||||||||||||||||
scalar · Enable_State · read-write · current After an AC power outage, Fast Charge automatically increases the float voltage of the DC power system to recharge the batteries as quickly as possible. Enable Fast Charge if the site experiences frequent AC power outages. | |||||||||||||||||||||
| Sfast-Charge-State | 1.3.6.1.4.1.1918.2.13.10.70.40.10 | Control_Process_State | RO | ||||||||||||||||||
scalar · Control_Process_State · read-only · current Indicates the state of Fast Charge process: Disabled, Inactive, Active or Pending. | |||||||||||||||||||||
| Sfast-Charge-Start-Allowed | 1.3.6.1.4.1.1918.2.13.10.70.40.12 | Can_Start | RO | ||||||||||||||||||
scalar · Can_Start · read-only · current Indicates if a Fast Charge is allowed to start or the reason why not. Fast Charge cannot start if there are no rectifiers with AC power, or the battery is not discharged. | |||||||||||||||||||||
| Sfast-Charge-Voltage | 1.3.6.1.4.1.1918.2.13.10.70.40.15 | Float | RW | ||||||||||||||||||
scalar · Float · read-write · current The bus voltage maintained during Fast Charge (use the value recommended by the battery manufacturer). Adjustments for Temperature Compensation and Battery Current Limit also apply.
| |||||||||||||||||||||
| Sfast-Charge-Offset-Voltage | 1.3.6.1.4.1.1918.2.13.10.70.40.17 | Float | RO | ||||||||||||||||||
scalar · Float · read-only · current The adjustment to the bus voltage being applied due to the Fast Charge.
| |||||||||||||||||||||
| Sfast-Charge-Ah-Discharged | 1.3.6.1.4.1.1918.2.13.10.70.40.20 | Float | RO | ||||||||||||||||||
scalar · Float · read-only · current The current level of battery discharge.
| |||||||||||||||||||||
| Sfast-Charge-Maximum-Duration | 1.3.6.1.4.1.1918.2.13.10.70.40.30 | TimeIntervalInMinutes | RW | ||||||||||||||||||
scalar · TimeIntervalInMinutes · read-write · current The maximum duration of a Fast Charge (use the value recommended by the battery manufacturer).
| |||||||||||||||||||||
| Sfast-Charge-Ampere-Hour-Threshold | 1.3.6.1.4.1.1918.2.13.10.70.40.35 | Unsigned8 | RW | ||||||||||||||||||
scalar · Unsigned8 · read-write · current If the battery has discharged more than this amount during a power outage, then Fast Charge occurs when AC power is restored. The threshold is given as a percentage of installed C10 battery capacity. Fast charge can also be triggered based on the Fast Charge Voltage Threshold.
| |||||||||||||||||||||
| Sfast-Charge-Voltage-Threshold | 1.3.6.1.4.1.1918.2.13.10.70.40.40 | Float | RW | ||||||||||||||||||
scalar · Float · read-write · current If the bus voltage drops below this value then Fast Charge occurs when AC power is restored. Fast charge can also be triggered based on the Fast Charge Ampere Hour Threshold.
| |||||||||||||||||||||
| Sfast-Charge-Recharge-Percentage | 1.3.6.1.4.1.1918.2.13.10.70.40.45 | Unsigned8 | RW | ||||||||||||||||||
scalar · Unsigned8 · read-write · current The ratio of recharge ampere-hours required to restore the battery to fully charged status to the ampere-hours discharged.
| |||||||||||||||||||||
| Sfast-Charge-Ampere-Hour-Stop-Threshold | 1.3.6.1.4.1.1918.2.13.10.70.40.47 | Unsigned8 | RW | ||||||||||||||||||
scalar · Unsigned8 · read-write · current Fast charge will only run until the charge removed from the battery falls below this threshold. This mostly useful when fast charge is used to control a generator and the generator should be stopped before the battery has been fully charged. The value given is a percentage of the configured battery capacity. This should normally be set to zero.
| |||||||||||||||||||||
| Sfast-Charge-Maximum-Time-Remaining | 1.3.6.1.4.1.1918.2.13.10.70.40.50 | TimeIntervalInSeconds | RO | ||||||||||||||||||
scalar · TimeIntervalInSeconds · read-only · current This timer is started when a Fast Charge cycle starts and runs while Fast Charge remains active. It is suspended and resumed when Fast Charge is suspended and resumed respectively. The Fast Charge cycle will stop if this timer reaches zero. The value is 0 if Fast Charge is inactive.
| |||||||||||||||||||||
| Sstop-Fast-Charge | 1.3.6.1.4.1.1918.2.13.10.70.40.100 | No_Data | RW | ||||||||||||||||||
scalar · No_Data · read-write · current This command stops the Fast Charge process if it is currently active. | |||||||||||||||||||||
| Nbattery-Current-Limit | 1.3.6.1.4.1.1918.2.13.10.70.50 | ||||||||||||||||||||
| Senable-Battery-Current-Limit | 1.3.6.1.4.1.1918.2.13.10.70.50.5 | Enable_State | RW | ||||||||||||||||||
scalar · Enable_State · read-write · current Protects the batteries from excessive charge current. BCL varies the system voltage in order to maintain battery charge current below the BCL Limit value. | |||||||||||||||||||||
| Sbcl-State | 1.3.6.1.4.1.1918.2.13.10.70.50.10 | BCL_State | RO | ||||||||||||||||||
scalar · BCL_State · read-only · current The state of the Battery Current Limit process. | |||||||||||||||||||||
| Sgenerator-State defined twice | 1.3.6.1.4.1.1918.2.13.10.70.50.20 | Engine_Run_State | RO | ||||||||||||||||||
scalar · Engine_Run_State · read-only · current Indicates whether or not the controller believes that the generator is currently running. This information may be based on a digital input (if configured) or derived from other information. | |||||||||||||||||||||
| Sbcl-Limit | 1.3.6.1.4.1.1918.2.13.10.70.50.30 | Unsigned8 | RW | ||||||||||||||||||
scalar · Unsigned8 · read-write · current BCL maintains the battery current below this value, which is a percentage of the installed C10 Battery Capacity.
| |||||||||||||||||||||
| Sbcl-Offset-Voltage | 1.3.6.1.4.1.1918.2.13.10.70.50.40 | Float | RO | ||||||||||||||||||
scalar · Float · read-only · current The bus voltage adjustment made by Battery Current Limit is applied to the Operating Voltage to produce the Target Voltage. Target Voltage is used as the input to the AVC function.
| |||||||||||||||||||||
| Sbcl-Engine-Run-Limit | 1.3.6.1.4.1.1918.2.13.10.70.50.50 | Unsigned8 | RW | ||||||||||||||||||
scalar · Unsigned8 · read-write · current The Battery Current Limit setting when Engine Run is active. BCL maintains the battery current below this value when the Engine Run digital input is active (Engine Run is enabled). This limit is expressed as a percentage of the installed C10 Battery Capacity.
| |||||||||||||||||||||
| Nbattery-Test | 1.3.6.1.4.1.1918.2.13.10.70.70 | ||||||||||||||||||||
| Senable-Battery-Test | 1.3.6.1.4.1.1918.2.13.10.70.70.3 | Enable_State | RW | ||||||||||||||||||
scalar · Enable_State · read-write · current Periodically tests the condition of the battery by reducing the rectifier voltage and allowing the batteries to discharge into the normal load. | |||||||||||||||||||||
| Sbattery-Test-Start-Allowed | 1.3.6.1.4.1.1918.2.13.10.70.70.7 | Can_Start | RO | ||||||||||||||||||
scalar · Can_Start · read-only · current Indicates if a Battery Test is allowed to start. Battery Tests cannot start within 48 hours of an AC failure, if there are no rectifiers, if Equalize or Fast Charge is active, if any rectifiers are failed or have lost communications, if the battery fuse has failed or if the system is overloaded. | |||||||||||||||||||||
| Sbattery-Test-Lockout-Remaining | 1.3.6.1.4.1.1918.2.13.10.70.70.8 | TimeIntervalInSeconds | RO | ||||||||||||||||||
scalar · TimeIntervalInSeconds · read-only · current How much longer the Battery Test is locked-out. Battery Tests cannot be started within 48 hours of an AC failure. If an immediate test is required, set Battery test Interval to zero (this disables the 48 hour lockout).
| |||||||||||||||||||||
| Sbattery-Test-State | 1.3.6.1.4.1.1918.2.13.10.70.70.10 | Battery_Test_State | RO | ||||||||||||||||||
scalar · Battery_Test_State · read-only · current The state of the Battery Test process. | |||||||||||||||||||||
| Sbattery-Test-First-Date-Time | 1.3.6.1.4.1.1918.2.13.10.70.70.15 | Julian_Time_UTC_25 | RO | ||||||||||||||||||
scalar · Julian_Time_UTC_25 · read-only · current The date and time that the first Battery Test will occur. Subsequent tests will occur at every Battery Test Interval after that. | |||||||||||||||||||||
| Sbattery-Test-Interval | 1.3.6.1.4.1.1918.2.13.10.70.70.17 | TimeIntervalInDays | RW | ||||||||||||||||||
scalar · TimeIntervalInDays · read-write · current The time between scheduled Battery Tests. The interval period begins at the start of a Battery Test. Zero disables scheduled Battery Tests. Zero also disables the 48 hour lockout following an AC failure, allowing an immediate manual test.
| |||||||||||||||||||||
| Snext-Battery-Test-Start-Time | 1.3.6.1.4.1.1918.2.13.10.70.70.20 | Julian_Time_UTC_25 | RO | ||||||||||||||||||
scalar · Julian_Time_UTC_25 · read-only · current The start time of the next scheduled Battery Test. | |||||||||||||||||||||
| Sbattery-Test-Duration | 1.3.6.1.4.1.1918.2.13.10.70.70.30 | TimeIntervalInMinutes | RW | ||||||||||||||||||
scalar · TimeIntervalInMinutes · read-write · current The maximum time a Battery Test process will be active. The Battery Test will pass if the bus voltage remains above the Battery Test Termination Voltage for the duration of the test.
| |||||||||||||||||||||
| Sbattery-Test-Remaining-Time | 1.3.6.1.4.1.1918.2.13.10.70.70.40 | TimeIntervalInSeconds | RO | ||||||||||||||||||
scalar · TimeIntervalInSeconds · read-only · current The time to the end of the currently active Battery Test.
| |||||||||||||||||||||
| Sbattery-Test-Termination-Voltage | 1.3.6.1.4.1.1918.2.13.10.70.70.50 | Float | RW | ||||||||||||||||||
scalar · Float · read-write · current If the bus voltages drops below this value during a Battery Test, then the test fails.
| |||||||||||||||||||||
| Sbattery-Test-Offset-Voltage | 1.3.6.1.4.1.1918.2.13.10.70.70.60 | Float | RO | ||||||||||||||||||
scalar · Float · read-only · current The adjustment to the bus voltage being applied due to the Battery Test. While a Battery Test is running, the rectifiers are turned down to force the battery to carry the load.
| |||||||||||||||||||||
| Sstart-Battery-Test | 1.3.6.1.4.1.1918.2.13.10.70.70.100 | No_Data | RW | ||||||||||||||||||
scalar · No_Data · read-write · current This command attempts to start the Battery Test process. | |||||||||||||||||||||
| Sstop-Battery-Test | 1.3.6.1.4.1.1918.2.13.10.70.70.110 | No_Data | RW | ||||||||||||||||||
scalar · No_Data · read-write · current This command stops the Battery Test process if it is currently active. | |||||||||||||||||||||
| Nlvd | 1.3.6.1.4.1.1918.2.13.10.70.75 | ||||||||||||||||||||
| Slvd-Inhibit-Period | 1.3.6.1.4.1.1918.2.13.10.70.75.10 | TimeIntervalInSeconds | RW | ||||||||||||||||||
scalar · TimeIntervalInSeconds · read-write · current The minimum time an LVD stays connected or disconnected before it can change state.
| |||||||||||||||||||||
| Sallow-Front-Panel-LVD-Control | 1.3.6.1.4.1.1918.2.13.10.70.75.20 | Boolean | RW | ||||||||||||||||||
scalar · Boolean · read-write · current This item specifies whether manual LVD control is allowed from the front panel. | |||||||||||||||||||||
| Tlvd-Table | 1.3.6.1.4.1.1918.2.13.10.70.75.50 | NA | |||||||||||||||||||
| Rlvd-Entry | 1.3.6.1.4.1.1918.2.13.10.70.75.50.1 | NA | |||||||||||||||||||
row · not-accessible · current
| |||||||||||||||||||||
| Clvd-Index | 1.3.6.1.4.1.1918.2.13.10.70.75.50.1.1 | Unsigned8 | RO | ||||||||||||||||||
column · Unsigned8 · read-only · current Automatically generated index object. | |||||||||||||||||||||
| Clvd-State | 1.3.6.1.4.1.1918.2.13.10.70.75.50.1.10 | LVD_State | RO | ||||||||||||||||||
column · LVD_State · read-only · current The state of this LVD control process. | |||||||||||||||||||||
| Clvd-Inhibited | 1.3.6.1.4.1.1918.2.13.10.70.75.50.1.15 | Boolean | RO | ||||||||||||||||||
column · Boolean · read-only · current Indicates whether this LVD currently cannot change state due to the inhibit time. | |||||||||||||||||||||
| Cenable-LVD-Voltage-Disconnect | 1.3.6.1.4.1.1918.2.13.10.70.75.50.1.20 | Enable_State | RW | ||||||||||||||||||
column · Enable_State · read-write · current If Enabled, the LVD will disconnect when the bus voltage falls below the Disconnect Voltage and will not reconnect until it is above the Reconnect Voltage. | |||||||||||||||||||||
| Clvd-Disconnect-Voltage | 1.3.6.1.4.1.1918.2.13.10.70.75.50.1.30 | Float | RW | ||||||||||||||||||
column · Float · read-write · current If voltage based disconnect is enabled, the LVD will disconnect if the bus voltage has been below this voltage for the recognition time.
| |||||||||||||||||||||
| Clvd-Reconnect-Voltage | 1.3.6.1.4.1.1918.2.13.10.70.75.50.1.40 | Float | RW | ||||||||||||||||||
column · Float · read-write · current If voltage based disconnect is enabled, the LVD will reconnect only if the bus voltage has been above this voltage for the recognition time.
| |||||||||||||||||||||
| Clvd-Recognition-Period | 1.3.6.1.4.1.1918.2.13.10.70.75.50.1.50 | TimeIntervalInSeconds | RW | ||||||||||||||||||
column · TimeIntervalInSeconds · read-write · current The time the bus voltage must be below or above the thresholds before the LVD disconnects or connects.
| |||||||||||||||||||||
| Cenable-LVD-AC-Timer | 1.3.6.1.4.1.1918.2.13.10.70.75.50.1.60 | Enable_State | RW | ||||||||||||||||||
column · Enable_State · read-write · current If Enabled, during an AC failure the LVD will disconnect after the AC Timer Delay, even if the Disconnect Voltage has not been reached. | |||||||||||||||||||||
| Clvd-AC-Timer-Disconnect-Delay | 1.3.6.1.4.1.1918.2.13.10.70.75.50.1.70 | TimeIntervalInMinutes | RW | ||||||||||||||||||
column · TimeIntervalInMinutes · read-write · current If Enabled, the LVD will disconnect after this delay following an AC failure, unless the Disconnect Voltage is reached or AC is restored first.
| |||||||||||||||||||||
| Cenable-LVD-SA-Disconnect | 1.3.6.1.4.1.1918.2.13.10.70.75.50.1.80 | Enable_State | RW | ||||||||||||||||||
column · Enable_State · read-write · current If Enabled, the LVD will disconnect immediately when the specified smart alarm becomes active. | |||||||||||||||||||||
| Clvd-SA-Disconnect-Index | 1.3.6.1.4.1.1918.2.13.10.70.75.50.1.90 | Unsigned8 | RW | ||||||||||||||||||
column · Unsigned8 · read-write · current If Enabled, the LVD will disconnect immediately when this smart alarm becomes active. | |||||||||||||||||||||
| Cenable-LVD-Chained-To-Previous | 1.3.6.1.4.1.1918.2.13.10.70.75.50.1.100 | Enable_State | RW | ||||||||||||||||||
column · Enable_State · read-write · current If Enabled, the LVD will not disconnect until the previous LVD (the LVD numbered one less) has been disconnected for the configured recognition time. This item is ignored by the first LVD and when the previous LVD has no contactors. This applies in reverse when connecting. | |||||||||||||||||||||
| Tlvdc-Table | 1.3.6.1.4.1.1918.2.13.10.70.75.60 | NA | |||||||||||||||||||
| Rlvdc-Entry | 1.3.6.1.4.1.1918.2.13.10.70.75.60.1 | NA | |||||||||||||||||||
row · not-accessible · current
| |||||||||||||||||||||
| Clvdc-Index | 1.3.6.1.4.1.1918.2.13.10.70.75.60.1.1 | Unsigned8 | RO | ||||||||||||||||||
column · Unsigned8 · read-only · current Automatically generated index object. | |||||||||||||||||||||
| Clvdc-LVD-Mapping | 1.3.6.1.4.1.1918.2.13.10.70.75.60.1.10 | Unsigned8 | RW | ||||||||||||||||||
column · Unsigned8 · read-write · current The logical LVD that drives this contactor. | |||||||||||||||||||||
| Clvdc-State | 1.3.6.1.4.1.1918.2.13.10.70.75.60.1.20 | LVDC_State | RO | ||||||||||||||||||
column · LVDC_State · read-only · current The state of this contactor. | |||||||||||||||||||||
| Cenable-LVDC | 1.3.6.1.4.1.1918.2.13.10.70.75.60.1.30 | Enable_State | RW | ||||||||||||||||||
column · Enable_State · read-write · current If Enabled, the specified physical contactor is driven by the specified logical LVD. | |||||||||||||||||||||
| Clvdc-IOB-Number | 1.3.6.1.4.1.1918.2.13.10.70.75.60.1.40 | Unsigned8 | RW | ||||||||||||||||||
column · Unsigned8 · read-write · current The I/O board number to which this LVD contactor is connected. | |||||||||||||||||||||
| Clvdc-IOB-LVD-Number | 1.3.6.1.4.1.1918.2.13.10.70.75.60.1.50 | Unsigned8 | RW | ||||||||||||||||||
column · Unsigned8 · read-write · current The LVD connector on the I/O board that this contactor is connected to. | |||||||||||||||||||||
| Clvdc-Type | 1.3.6.1.4.1.1918.2.13.10.70.75.60.1.60 | LVDC_Type | RW | ||||||||||||||||||
column · LVDC_Type · read-write · current The type of contactor connected to the I/O board. | |||||||||||||||||||||
| Ngenerator-Control | 1.3.6.1.4.1.1918.2.13.10.70.80 | ||||||||||||||||||||
| Sgenerator-Fail-Alarm-Recognition-Period | 1.3.6.1.4.1.1918.2.13.10.70.80.100 | TimeIntervalInSeconds | RW | ||||||||||||||||||
scalar · TimeIntervalInSeconds · read-write · current Recognition period for the Generator Fail Alarm. The alarm will activate if the Generator Enable Alarm has been triggered for this period and AC has not been restored.
| |||||||||||||||||||||
| Sgenerator-On-Fast-Charge | 1.3.6.1.4.1.1918.2.13.10.70.80.110 | YesNo | RW | ||||||||||||||||||
scalar · YesNo · read-write · current The controller will activate the generator control relay while fast charge is pending or active. | |||||||||||||||||||||
| Sgenerator-On-Equalize | 1.3.6.1.4.1.1918.2.13.10.70.80.112 | YesNo | RW | ||||||||||||||||||
scalar · YesNo · read-write · current The controller will activate the generator control relay while equalize is pending or active. | |||||||||||||||||||||
| Sgenerator-On-Mains-Failure | 1.3.6.1.4.1.1918.2.13.10.70.80.116 | YesNo | RW | ||||||||||||||||||
scalar · YesNo · read-write · current The controller will activate the generator control relay when there is a mains failure. | |||||||||||||||||||||
| Sac-Supply-State | 1.3.6.1.4.1.1918.2.13.10.70.80.120 | System_State | RO | ||||||||||||||||||
scalar · System_State · read-only · current Calculated AC Supply state. | |||||||||||||||||||||
| Sgenerator-Run-Time-Remaining | 1.3.6.1.4.1.1918.2.13.10.70.80.130 | TimeIntervalInSeconds | RO | ||||||||||||||||||
scalar · TimeIntervalInSeconds · read-only · current The time left for the generator to run following a manual start.
| |||||||||||||||||||||
| Sgenerator-State defined twice | 1.3.6.1.4.1.1918.2.13.10.70.80.140 | Engine_Run_State | RO | ||||||||||||||||||
scalar · Engine_Run_State · read-only · current Indicates whether or not the controller believes that the generator is currently running. This information may be based on a digital input (if configured) or derived from other information. | |||||||||||||||||||||
| Sgenerator-Refuel-Date | 1.3.6.1.4.1.1918.2.13.10.70.80.150 | Julian_Time_UTC_25 | RO | ||||||||||||||||||
scalar · Julian_Time_UTC_25 · read-only · current The time and date the generator was last refuelled. | |||||||||||||||||||||
| Sgenerator-Refuel-Volume | 1.3.6.1.4.1.1918.2.13.10.70.80.160 | Float | RO | ||||||||||||||||||
scalar · Float · read-only · current The amount of fuel added to the generator's fuel tank(s) during the last refuel.
| |||||||||||||||||||||
| Sgenerator-Backup-Time | 1.3.6.1.4.1.1918.2.13.10.70.80.170 | TimeIntervalInSeconds | RO | ||||||||||||||||||
scalar · TimeIntervalInSeconds · read-only · current Estimated time for which the generator could continuously run based on the current fuel-level and historic fuel consumption.
| |||||||||||||||||||||
| Stank-Empty-Date-Time | 1.3.6.1.4.1.1918.2.13.10.70.80.180 | Julian_Time_UTC_25 | RO | ||||||||||||||||||
scalar · Julian_Time_UTC_25 · read-only · current Best current estimate of the date at which the tank will run dry if the current characteristics of generator usage do not change. This is useful for installations that run the generator regularly and with a reasonably constant duty cycle. | |||||||||||||||||||||
| Sfuel-Level | 1.3.6.1.4.1.1918.2.13.10.70.80.190 | Float | RO | ||||||||||||||||||
scalar · Float · read-only · current The volume of fuel in the generator's fuel tank(s).
| |||||||||||||||||||||
| Sgenerator-Control-Relay | 1.3.6.1.4.1.1918.2.13.10.70.80.200 | Relay_Mapping | RW | ||||||||||||||||||
scalar · Relay_Mapping · read-write · current The relay used to control generator startup and shutdown. If this is set to None, the generator control process is disabled. | |||||||||||||||||||||
| Sgenerator-Startup-Wiring | 1.3.6.1.4.1.1918.2.13.10.70.80.210 | Generator_Startup_Wiring | RW | ||||||||||||||||||
scalar · Generator_Startup_Wiring · read-write · current Choose to match the way the generator control relay is wired. | |||||||||||||||||||||
| Smanual-Generator-Run-Time | 1.3.6.1.4.1.1918.2.13.10.70.80.230 | TimeIntervalInMinutes | RW | ||||||||||||||||||
scalar · TimeIntervalInMinutes · read-write · current The maximum time permitted for the generator to run following a manual start.
| |||||||||||||||||||||
| Sfuel-Tank-Volume | 1.3.6.1.4.1.1918.2.13.10.70.80.240 | Float | RW | ||||||||||||||||||
scalar · Float · read-write · current The total volume of the generator's fuel tank(s). A value of 0 disables fuel related estimates.
| |||||||||||||||||||||
| Smanual-Generator-Start | 1.3.6.1.4.1.1918.2.13.10.70.80.260 | No_Data | RW | ||||||||||||||||||
scalar · No_Data · read-write · current This causes the generator to run for the configured time unless it is manually stopped. | |||||||||||||||||||||
| Smanual-Generator-Stop | 1.3.6.1.4.1.1918.2.13.10.70.80.270 | No_Data | RW | ||||||||||||||||||
scalar · No_Data · read-write · current This will end a manual generator run before the time has elapsed. It will not cause the generator to stop if it is running based on fast charge, equalize or AC failure. | |||||||||||||||||||||
| Sclear-Fuel-Consumption-History | 1.3.6.1.4.1.1918.2.13.10.70.80.280 | No_Data | RW | ||||||||||||||||||
scalar · No_Data · read-write · current The controller accumulates historic information on the average generator fuel consumption and, in applications that run the generator regularly, the average generator duty cycle. This command will clear this information for instance when the generator has been replaced. This will cause the remaining time estimates to be very inaccurate or not available until enough information about the new generator has been collected. | |||||||||||||||||||||
| Nreal-Time-Clock | 1.3.6.1.4.1.1918.2.13.10.80 | ||||||||||||||||||||
| Scontroller-Time | 1.3.6.1.4.1.1918.2.13.10.80.10 | Julian_Time_UTC_25 | RO | ||||||||||||||||||
scalar · Julian_Time_UTC_25 · read-only · current The current time of the controller's internal battery backed clock. | |||||||||||||||||||||
| Ninput-Output | 1.3.6.1.4.1.1918.2.13.10.90 | ||||||||||||||||||||
| Nsystem-Analog-Input | 1.3.6.1.4.1.1918.2.13.10.90.10 | ||||||||||||||||||||
| Tanalog-Input-Table | 1.3.6.1.4.1.1918.2.13.10.90.10.30 | NA | |||||||||||||||||||
| Ranalog-Input-Entry | 1.3.6.1.4.1.1918.2.13.10.90.10.30.1 | NA | |||||||||||||||||||
row · not-accessible · current
| |||||||||||||||||||||
| Canalog-Input-Index | 1.3.6.1.4.1.1918.2.13.10.90.10.30.1.1 | Unsigned8 | RO | ||||||||||||||||||
column · Unsigned8 · read-only · current Automatically generated index object. | |||||||||||||||||||||
| Cai-High-State | 1.3.6.1.4.1.1918.2.13.10.90.10.30.1.20 | Alarm_Active_State | RO | ||||||||||||||||||
column · Alarm_Active_State · read-only · current The state of the selected analog input high alarm. | |||||||||||||||||||||
| Cai-Low-State | 1.3.6.1.4.1.1918.2.13.10.90.10.30.1.30 | Alarm_Active_State | RO | ||||||||||||||||||
column · Alarm_Active_State · read-only · current The state of the selected analog input low alarm. | |||||||||||||||||||||
| Cai-Value | 1.3.6.1.4.1.1918.2.13.10.90.10.30.1.40 | Float | RO | ||||||||||||||||||
column · Float · read-only · current Analog input value.
| |||||||||||||||||||||
| Cai-Status | 1.3.6.1.4.1.1918.2.13.10.90.10.30.1.50 | Enable_State | RW | ||||||||||||||||||
column · Enable_State · read-write · current Enable/disable this analog input channel. | |||||||||||||||||||||
| Cai-Name | 1.3.6.1.4.1.1918.2.13.10.90.10.30.1.60 | Display_20 | RW | ||||||||||||||||||
column · Display_20 · read-write · current The name of this analog input channel as it will appear on management software such as DCTools or PowerManagerII. This name is not displayed on the controller. | |||||||||||||||||||||
| Cai-Units | 1.3.6.1.4.1.1918.2.13.10.90.10.30.1.70 | Measurement_Units | RW | ||||||||||||||||||
column · Measurement_Units · read-write · current Units of this analog input (after scaling). | |||||||||||||||||||||
| Cai-IOB-Number | 1.3.6.1.4.1.1918.2.13.10.90.10.30.1.80 | Unsigned8 | RW | ||||||||||||||||||
column · Unsigned8 · read-write · current The I/O board number on which this analog input is located. | |||||||||||||||||||||
| Cinput-Number | 1.3.6.1.4.1.1918.2.13.10.90.10.30.1.90 | Unsigned8 | RW | ||||||||||||||||||
column · Unsigned8 · read-write · current The input channel on the I/O board of this analog input. | |||||||||||||||||||||
| Cgain | 1.3.6.1.4.1.1918.2.13.10.90.10.30.1.100 | Float | RW | ||||||||||||||||||
column · Float · read-write · current The scaling factor applied to the raw value read from the I/O board.
| |||||||||||||||||||||
| Coffset | 1.3.6.1.4.1.1918.2.13.10.90.10.30.1.110 | Float | RW | ||||||||||||||||||
column · Float · read-write · current The offset applied to the raw value read from the I/O board.
| |||||||||||||||||||||
| Chysteresis | 1.3.6.1.4.1.1918.2.13.10.90.10.30.1.130 | Float | RW | ||||||||||||||||||
column · Float · read-write · current The amount of hysteresis applied to the input before an active alarm is deactivated.
| |||||||||||||||||||||
| Chigh-Severity | 1.3.6.1.4.1.1918.2.13.10.90.10.30.1.141 | Alarm_Severity | RW | ||||||||||||||||||
column · Alarm_Severity · read-write · current The severity level associated with the alarm. Control alarms are not displayed, although any configured digital outputs are still activated. | |||||||||||||||||||||
| Chigh-Threshold | 1.3.6.1.4.1.1918.2.13.10.90.10.30.1.150 | Float | RW | ||||||||||||||||||
column · Float · read-write · current An analog input high alarm is activated if the scaled input is greater than or equal to this value.
| |||||||||||||||||||||
| Chigh-DO-Mapping-A | 1.3.6.1.4.1.1918.2.13.10.90.10.30.1.160 | Relay_Mapping | RW | ||||||||||||||||||
column · Relay_Mapping · read-write · current Optional digital output activated while this alarm is active. | |||||||||||||||||||||
| Chigh-DO-Mapping-B | 1.3.6.1.4.1.1918.2.13.10.90.10.30.1.170 | Relay_Mapping | RW | ||||||||||||||||||
column · Relay_Mapping · read-write · current Optional digital output activated while this alarm is active. | |||||||||||||||||||||
| Chigh-Send-Trap | 1.3.6.1.4.1.1918.2.13.10.90.10.30.1.175 | Boolean | RW | ||||||||||||||||||
column · Boolean · read-write · current If set to true an SNMP trap is sent to every trap receiver with an appropriate trap level whenever this alarm changes state. | |||||||||||||||||||||
| Clow-Severity | 1.3.6.1.4.1.1918.2.13.10.90.10.30.1.181 | Alarm_Severity | RW | ||||||||||||||||||
column · Alarm_Severity · read-write · current The severity level associated with the alarm. Control alarms are not displayed, although any configured digital outputs are still activated. | |||||||||||||||||||||
| Clow-Threshold | 1.3.6.1.4.1.1918.2.13.10.90.10.30.1.190 | Float | RW | ||||||||||||||||||
column · Float · read-write · current An analog input low alarm is activated if the scaled input is lower than or equal to this value.
| |||||||||||||||||||||
| Clow-DO-Mapping-A | 1.3.6.1.4.1.1918.2.13.10.90.10.30.1.200 | Relay_Mapping | RW | ||||||||||||||||||
column · Relay_Mapping · read-write · current Optional digital output activated while this alarm is active. | |||||||||||||||||||||
| Clow-DO-Mapping-B | 1.3.6.1.4.1.1918.2.13.10.90.10.30.1.210 | Relay_Mapping | RW | ||||||||||||||||||
column · Relay_Mapping · read-write · current Optional digital output activated while this alarm is active. | |||||||||||||||||||||
| Clow-Send-Trap | 1.3.6.1.4.1.1918.2.13.10.90.10.30.1.215 | Boolean | RW | ||||||||||||||||||
column · Boolean · read-write · current If set to true an SNMP trap is sent to every trap receiver with an appropriate trap level whenever this alarm changes state. | |||||||||||||||||||||
| Cai-Group | 1.3.6.1.4.1.1918.2.13.10.90.10.30.1.220 | Unsigned8 | RW | ||||||||||||||||||
column · Unsigned8 · read-write · current The group tag used by PowerManagerII to group related inputs and outputs for display purposes. | |||||||||||||||||||||
| Cai-High-Notes | 1.3.6.1.4.1.1918.2.13.10.90.10.30.1.230 | Display_60 | RW | ||||||||||||||||||
column · Display_60 · read-write · current User notes about this alarm. These notes appear in SNMP traps and can be viewed using DCTools or PowerManagerII. | |||||||||||||||||||||
| Cai-Low-Notes | 1.3.6.1.4.1.1918.2.13.10.90.10.30.1.240 | Display_60 | RW | ||||||||||||||||||
column · Display_60 · read-write · current User notes about this alarm. These notes appear in SNMP traps and can be viewed using DCTools or PowerManagerII. | |||||||||||||||||||||
| Nalternative-Energy-Source | 1.3.6.1.4.1.1918.2.13.10.90.10.50 | ||||||||||||||||||||
| Salternative-Source-Current | 1.3.6.1.4.1.1918.2.13.10.90.10.50.10 | Float | RO | ||||||||||||||||||
scalar · Float · read-only · current The total current produced by all alternative energy sources. This value is measured by the alternative energy shunt(s) if present. If none are configured the controller assumes that there are no alternative energy sources present.
| |||||||||||||||||||||
| Nsystem-States | 1.3.6.1.4.1.1918.2.13.10.90.15 | ||||||||||||||||||||
| Smains-Fail | 1.3.6.1.4.1.1918.2.13.10.90.15.10 | System_State | RO | ||||||||||||||||||
scalar · System_State · read-only · current Failed if any Mains Fail digital input is in active state. | |||||||||||||||||||||
| Sfan-Fail | 1.3.6.1.4.1.1918.2.13.10.90.15.20 | System_State | RO | ||||||||||||||||||
scalar · System_State · read-only · current Failed if any ACD Fan Fail digital input is in active state. | |||||||||||||||||||||
| Smov-Fail | 1.3.6.1.4.1.1918.2.13.10.90.15.30 | System_State | RO | ||||||||||||||||||
scalar · System_State · read-only · current Failed if any MOV Fail digital input is in active state. | |||||||||||||||||||||
| Sload-Fuse-Fail | 1.3.6.1.4.1.1918.2.13.10.90.15.40 | System_State | RO | ||||||||||||||||||
scalar · System_State · read-only · current Failed if any Load Fuse Fail digital input is in active state. | |||||||||||||||||||||
| Sbattery-Fuse-Fail | 1.3.6.1.4.1.1918.2.13.10.90.15.50 | System_State | RO | ||||||||||||||||||
scalar · System_State · read-only · current Failed if any Battery Fuse Fail digital input is in active state. | |||||||||||||||||||||
| Sphase-Fail | 1.3.6.1.4.1.1918.2.13.10.90.15.60 | System_State | RO | ||||||||||||||||||
scalar · System_State · read-only · current Failed if any Phase Fail digital input is in active state. | |||||||||||||||||||||
| Tdigital-Input-Table | 1.3.6.1.4.1.1918.2.13.10.90.40 | NA | |||||||||||||||||||
| Rdigital-Input-Entry | 1.3.6.1.4.1.1918.2.13.10.90.40.1 | NA | |||||||||||||||||||
row · not-accessible · current
| |||||||||||||||||||||
| Cdigital-Input-Index | 1.3.6.1.4.1.1918.2.13.10.90.40.1.1 | Unsigned8 | RO | 1 | |||||||||||||||||
column · Unsigned8 · read-only · current Automatically generated index object. Example values from LibreNMS test devices
| |||||||||||||||||||||
| Cdi-State | 1.3.6.1.4.1.1918.2.13.10.90.40.1.20 | Alarm_Active_State | RO | 0 | |||||||||||||||||
column · Alarm_Active_State · read-only · current The state of this digital input alarm. Example values from LibreNMS test devices
| |||||||||||||||||||||
| Cdi-Value | 1.3.6.1.4.1.1918.2.13.10.90.40.1.30 | Digital_Input_State | RO | 3 | |||||||||||||||||
column · Digital_Input_State · read-only · current The state of this digital input. Example values from LibreNMS test devices
| |||||||||||||||||||||
| Cdi-Status | 1.3.6.1.4.1.1918.2.13.10.90.40.1.40 | Enable_State | RW | 1 | |||||||||||||||||
column · Enable_State · read-write · current Enable/disable this digital input channel. Example values from LibreNMS test devices
| |||||||||||||||||||||
| Cdi-Name | 1.3.6.1.4.1.1918.2.13.10.90.40.1.50 | Display_20 | RW | Digital Input 1 | |||||||||||||||||
column · Display_20 · read-write · current The name of the digital input. Example values from LibreNMS test devices
| |||||||||||||||||||||
| Cdi-IOB-Number | 1.3.6.1.4.1.1918.2.13.10.90.40.1.60 | Unsigned8 | RW | 1 | |||||||||||||||||
column · Unsigned8 · read-write · current The I/O board number on which this digital input is located. Example values from LibreNMS test devices
| |||||||||||||||||||||
| Cdigital-Input-Number | 1.3.6.1.4.1.1918.2.13.10.90.40.1.70 | Unsigned8 | RW | 1 | |||||||||||||||||
column · Unsigned8 · read-write · current The input channel on the I/O board of this digital input. Example values from LibreNMS test devices
| |||||||||||||||||||||
| Cdi-Severity | 1.3.6.1.4.1.1918.2.13.10.90.40.1.81 | Alarm_Severity | RW | 0 | |||||||||||||||||
column · Alarm_Severity · read-write · current The severity level associated with the alarm. Control alarms are not displayed, although any configured digital outputs are still activated. Example values from LibreNMS test devices
| |||||||||||||||||||||
| Cdi-Recognition-Period | 1.3.6.1.4.1.1918.2.13.10.90.40.1.85 | TimeIntervalInSeconds | RW | 1000 (0d 0h 0m 10s) | |||||||||||||||||
column · TimeIntervalInSeconds · read-write · current A digital input alarm will become active if the input is in the active state for the recognition time.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| Cdi-Deactivation-Recognition-Period | 1.3.6.1.4.1.1918.2.13.10.90.40.1.86 | TimeIntervalInSeconds | RW | 0 (0d 0h 0m 0s) | |||||||||||||||||
column · TimeIntervalInSeconds · read-write · current A digital input alarm will deactivate if the input is in the inactive state for the deactivation recognition time.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| Cdi-DO-Mapping-A | 1.3.6.1.4.1.1918.2.13.10.90.40.1.90 | Relay_Mapping | RW | 0 | |||||||||||||||||
column · Relay_Mapping · read-write · current Optional digital output activated while this digital input alarm is active. Example values from LibreNMS test devices
| |||||||||||||||||||||
| Cdi-DO-Mapping-B | 1.3.6.1.4.1.1918.2.13.10.90.40.1.100 | Relay_Mapping | RW | 0 | |||||||||||||||||
column · Relay_Mapping · read-write · current Optional digital output activated while this digital input alarm is active. Example values from LibreNMS test devices
| |||||||||||||||||||||
| Cdi-Send-Trap | 1.3.6.1.4.1.1918.2.13.10.90.40.1.105 | Boolean | RW | 1 | |||||||||||||||||
column · Boolean · read-write · current If set to true an SNMP trap is sent to every trap receiver with an appropriate trap level whenever this alarm changes state. Example values from LibreNMS test devices
| |||||||||||||||||||||
| Cdi-Active-State | 1.3.6.1.4.1.1918.2.13.10.90.40.1.110 | Active_State | RW | 2 | |||||||||||||||||
column · Active_State · read-write · current Selects whether the input should be considered active when closed or open. Example values from LibreNMS test devices
| |||||||||||||||||||||
| Cdi-Group | 1.3.6.1.4.1.1918.2.13.10.90.40.1.120 | Unsigned8 | RW | 0 | |||||||||||||||||
column · Unsigned8 · read-write · current The group Number to be used by SiteManager. Example values from LibreNMS test devices
| |||||||||||||||||||||
| Cdi-Notes | 1.3.6.1.4.1.1918.2.13.10.90.40.1.130 | Display_60 | RW | | |||||||||||||||||
column · Display_60 · read-write · current User notes about this alarm. These notes appear in SNMP traps and can be viewed using DCTools or PowerManagerII. Example values from LibreNMS test devices
| |||||||||||||||||||||
| Tdigital-Output-Table | 1.3.6.1.4.1.1918.2.13.10.90.50 | NA | |||||||||||||||||||
| Rdigital-Output-Entry | 1.3.6.1.4.1.1918.2.13.10.90.50.1 | NA | |||||||||||||||||||
row · not-accessible · current
| |||||||||||||||||||||
| Cdigital-Output-Index | 1.3.6.1.4.1.1918.2.13.10.90.50.1.1 | Unsigned8 | RO | ||||||||||||||||||
column · Unsigned8 · read-only · current Automatically generated index object. | |||||||||||||||||||||
| Cdo-State | 1.3.6.1.4.1.1918.2.13.10.90.50.1.20 | External_Relay_State | RO | ||||||||||||||||||
column · External_Relay_State · read-only · current The state of this digital output. Active digital outputs may be energized or de-energized depending on their configuration. | |||||||||||||||||||||
| Cremote-Control-State | 1.3.6.1.4.1.1918.2.13.10.90.50.1.40 | Relay_Control_State | RW | ||||||||||||||||||
column · Relay_Control_State · read-write · current Allows manual control of the digital output. | |||||||||||||||||||||
| Cdo-Status | 1.3.6.1.4.1.1918.2.13.10.90.50.1.50 | Enable_State | RW | ||||||||||||||||||
column · Enable_State · read-write · current Enable or disable this digital output. If disabled, the digital output is not driven. | |||||||||||||||||||||
| Cdo-Name | 1.3.6.1.4.1.1918.2.13.10.90.50.1.60 | Display_20 | RW | ||||||||||||||||||
column · Display_20 · read-write · current The name of the digital output. | |||||||||||||||||||||
| Cdo-IOB-Number | 1.3.6.1.4.1.1918.2.13.10.90.50.1.70 | Unsigned8 | RW | ||||||||||||||||||
column · Unsigned8 · read-write · current The I/O board number on which this digital output is located. | |||||||||||||||||||||
| Cdo-IOB-DO-Number | 1.3.6.1.4.1.1918.2.13.10.90.50.1.80 | Unsigned8 | RW | ||||||||||||||||||
column · Unsigned8 · read-write · current The number of the digital output channel on the I/O board. | |||||||||||||||||||||
| Cdo-Active-State | 1.3.6.1.4.1.1918.2.13.10.90.50.1.90 | Energize_State | RW | ||||||||||||||||||
column · Energize_State · read-write · current Active state of the digital output. | |||||||||||||||||||||
| Cdo-Group | 1.3.6.1.4.1.1918.2.13.10.90.50.1.100 | Unsigned8 | RW | ||||||||||||||||||
column · Unsigned8 · read-write · current The Group Number to be used by SiteManager. | |||||||||||||||||||||
| Nbattery | 1.3.6.1.4.1.1918.2.13.10.100 | ||||||||||||||||||||
| Sbattery-Capacity | 1.3.6.1.4.1.1918.2.13.10.100.10 | Counter32 | RW | ||||||||||||||||||
scalar · Counter32 · read-write · current The rated 10-hour (C10) capacity of the battery. 0 = no battery is installed.
| |||||||||||||||||||||
| Scells-Per-String | 1.3.6.1.4.1.1918.2.13.10.100.20 | Unsigned8 | RW | ||||||||||||||||||
scalar · Unsigned8 · read-write · current The number of 2V battery cells per string. Zero means no battery is installed. | |||||||||||||||||||||
| Sbattery-Temperature | 1.3.6.1.4.1.1918.2.13.10.100.30 | Float | RO | 17 | |||||||||||||||||
scalar · Float · read-only · current The average of all analog inputs configured as battery temperature inputs.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| Sbattery-Current | 1.3.6.1.4.1.1918.2.13.10.100.40 | Float | RO | 0 | |||||||||||||||||
scalar · Float · read-only · current The total current flowing to/from the batteries. If positive, the battery is being charged. This value may be measured by the battery current shunt(s) if present or calculated from the other system currents.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| Sbattery-Type | 1.3.6.1.4.1.1918.2.13.10.100.42 | Display_20 | RW | ||||||||||||||||||
scalar · Display_20 · read-write · current The name or type of the battery. | |||||||||||||||||||||
| Sbtr-Time-Remaining | 1.3.6.1.4.1.1918.2.13.10.100.43 | TimeIntervalInSeconds | RO | ||||||||||||||||||
scalar · TimeIntervalInSeconds · read-only · current An estimate of the time remaining until the average cell discharge voltage reaches the configured end voltage. This value is only available during a discharge if the battery has been characterized.
| |||||||||||||||||||||
| Sbtr-State-Of-Health | 1.3.6.1.4.1.1918.2.13.10.100.44 | Percentile8NAN | RO | ||||||||||||||||||
scalar · Percentile8NAN · read-only · current The health of the battery measured as the estimated C10 capacity at the end of the last discharge as a percentage of the configured capacity. The accuracy of this value depends on the depth of the last discharge and it is only updated if the battery is discharged by at least 25% of its estimated capacity.
| |||||||||||||||||||||
| Sbattery-Charge-State | 1.3.6.1.4.1.1918.2.13.10.100.45 | Battery_Charge_State | RO | ||||||||||||||||||
scalar · Battery_Charge_State · read-only · current Indicates the current state of the battery. | |||||||||||||||||||||
| Sbattery-State-Threshold | 1.3.6.1.4.1.1918.2.13.10.100.47 | Float | RW | ||||||||||||||||||
scalar · Float · read-write · current The threshold used to determine the battery state. If the battery current is greater than the value, the battery state is Charge. If the battery current is less than the negative of this value, the battery state is Discharge. Otherwise, it is Float. A 10% hysteresis applies.
| |||||||||||||||||||||
| Send-Of-Charge-Action | 1.3.6.1.4.1.1918.2.13.10.100.48 | End_Of_Charge_Action | RW | ||||||||||||||||||
scalar · End_Of_Charge_Action · read-write · current To ensure that there is no residual AhD error at the end of the charge, AhD can be set to zero after each charge. For new installations, Set Ah Discharged to zero after Equalize and Fast Charge. | |||||||||||||||||||||
| Nmidpoint-Monitoring | 1.3.6.1.4.1.1918.2.13.10.100.50 | ||||||||||||||||||||
| Smpm-Lockout-Period | 1.3.6.1.4.1.1918.2.13.10.100.50.20 | TimeIntervalInMinutes | RW | ||||||||||||||||||
scalar · TimeIntervalInMinutes · read-write · current Time period from when battery ceases discharging or the completion of Fast Charge, Equalize or Battery Test during which midpoint battery monitoring shall not operate.
| |||||||||||||||||||||
| Smpm-Convergence-Period | 1.3.6.1.4.1.1918.2.13.10.100.50.30 | TimeIntervalInMinutes | RW | ||||||||||||||||||
scalar · TimeIntervalInMinutes · read-write · current Time period from start of the MPM process. During this period the MPM threshold is calculated via linear interpolation using MPM Start Threshold, Stable Threshold and the Time Running.
| |||||||||||||||||||||
| Sstring-Fail-Recognition-Period | 1.3.6.1.4.1.1918.2.13.10.100.50.40 | TimeIntervalInMinutes | RW | ||||||||||||||||||
scalar · TimeIntervalInMinutes · read-write · current If the midpoint voltage divergence of a battery string is continuously over threshold for this time, the string is deemed faulty.
| |||||||||||||||||||||
| Smpm-Start-Threshold | 1.3.6.1.4.1.1918.2.13.10.100.50.50 | Float | RW | ||||||||||||||||||
scalar · Float · read-write · current Midpoint battery monitoring start threshold, defined as percentage of bus voltage.
| |||||||||||||||||||||
| Smpm-Stable-Threshold | 1.3.6.1.4.1.1918.2.13.10.100.50.60 | Float | RW | ||||||||||||||||||
scalar · Float · read-write · current Midpoint battery monitoring stable threshold, defined as percentage of bus voltage.
| |||||||||||||||||||||
| Tmidpoint-Monitoring-String-Table | 1.3.6.1.4.1.1918.2.13.10.100.50.70 | NA | |||||||||||||||||||
| Rmidpoint-Monitoring-String-Entry | 1.3.6.1.4.1.1918.2.13.10.100.50.70.1 | NA | |||||||||||||||||||
row · not-accessible · current | |||||||||||||||||||||
| Cmidpoint-Monitoring-String-Index | 1.3.6.1.4.1.1918.2.13.10.100.50.70.1.1 | Unsigned8 | RO | ||||||||||||||||||
column · Unsigned8 · read-only · current Automatically generated index object. | |||||||||||||||||||||
| Cstring-Name | 1.3.6.1.4.1.1918.2.13.10.100.50.70.1.10 | Display_20 | RO | ||||||||||||||||||
column · Display_20 · read-only · current Name of the battery string. | |||||||||||||||||||||
| Cstring-State | 1.3.6.1.4.1.1918.2.13.10.100.50.70.1.20 | MPM_Battery_State | RO | ||||||||||||||||||
column · MPM_Battery_State · read-only · current Indicates the current state of a battery string. | |||||||||||||||||||||
| Cmidpoint-Voltage | 1.3.6.1.4.1.1918.2.13.10.100.50.70.1.30 | Float | RO | ||||||||||||||||||
column · Float · read-only · current Midpoint voltage reading for the battery string.
| |||||||||||||||||||||
| Cimbalance-Percent | 1.3.6.1.4.1.1918.2.13.10.100.50.70.1.40 | Float | RO | ||||||||||||||||||
column · Float · read-only · current The voltage difference between the first half of the string and the second half of the string expressed in percent of the Bus Voltage.
| |||||||||||||||||||||
| Smpm-State | 1.3.6.1.4.1.1918.2.13.10.100.50.80 | MPM_State | RO | ||||||||||||||||||
scalar · MPM_State · read-only · current Indicates the current state of the MPM process. | |||||||||||||||||||||
| Stime-In-This-State | 1.3.6.1.4.1.1918.2.13.10.100.50.90 | TimeIntervalInMinutes | RO | ||||||||||||||||||
scalar · TimeIntervalInMinutes · read-only · current Indicates the time period that the current MPM state has been running for.
| |||||||||||||||||||||
| Scurrent-MPM-Threshold | 1.3.6.1.4.1.1918.2.13.10.100.50.100 | Float | RO | ||||||||||||||||||
scalar · Float · read-only · current Indicates the current calculated MPM threshold.
| |||||||||||||||||||||
| Sreference-Voltage | 1.3.6.1.4.1.1918.2.13.10.100.50.105 | Float | RO | ||||||||||||||||||
scalar · Float · read-only · current Midpoint reference voltage.
| |||||||||||||||||||||
| Sclear-String-Fail | 1.3.6.1.4.1.1918.2.13.10.100.50.110 | No_Data | RW | ||||||||||||||||||
scalar · No_Data · read-write · current This command attempts to reset string state. | |||||||||||||||||||||
| Nbattery-Time-Remaining | 1.3.6.1.4.1.1918.2.13.10.100.60 | ||||||||||||||||||||
| Sbtr-State | 1.3.6.1.4.1.1918.2.13.10.100.60.10 | BTR_State | RO | 5 | |||||||||||||||||
scalar · BTR_State · read-only · current The state of the battery time remaining algorithm. Example values from LibreNMS test devices
| |||||||||||||||||||||
| Sbtr-End-Voltage | 1.3.6.1.4.1.1918.2.13.10.100.60.20 | Float | RW | ||||||||||||||||||
scalar · Float · read-write · current During a discharge the controller will provide an estimate of the time remaining until the average cell discharge voltage reaches this value.
| |||||||||||||||||||||
| Sbtr-Characterization-End-Voltage | 1.3.6.1.4.1.1918.2.13.10.100.60.30 | Float | RO | ||||||||||||||||||
scalar · Float · read-only · current The end voltage that the battery was last characterized to. For the controller to be able to estimate a remaining time, this value must be below the configured end voltage.
| |||||||||||||||||||||
| Sbtr-Characterization-Result | 1.3.6.1.4.1.1918.2.13.10.100.60.40 | BTR_Characterization_Result | RO | 3 | |||||||||||||||||
scalar · BTR_Characterization_Result · read-only · current Indicates the result of the last characterization. Example values from LibreNMS test devices
| |||||||||||||||||||||
| Sbtr-Characterization-Time | 1.3.6.1.4.1.1918.2.13.10.100.60.50 | Julian_Time_UTC_25 | RO | ||||||||||||||||||
scalar · Julian_Time_UTC_25 · read-only · current End time of the last characterization. | |||||||||||||||||||||
| Sbtr-Automatic-Characterization | 1.3.6.1.4.1.1918.2.13.10.100.60.60 | Enable_State | RW | ||||||||||||||||||
scalar · Enable_State · read-write · current If enabled, the controller will automatically perform a characterization when all necessary conditions have been met for the characterization delay. If the characterization fails, the controller will retry the characterization twice until a valid characterization is obtained. At the end of the third characterization or when successfully characterized, the controller will automatically disable this function. | |||||||||||||||||||||
| Sbtr-Characterization-Delay | 1.3.6.1.4.1.1918.2.13.10.100.60.70 | TimeIntervalInMinutes | RW | ||||||||||||||||||
scalar · TimeIntervalInMinutes · read-write · current If automatic characterization is enabled, the controller will automatically perform a battery characterization discharge when all conditions have been met for this time.
| |||||||||||||||||||||
| Sbtr-Characterization-Start | 1.3.6.1.4.1.1918.2.13.10.100.60.80 | TimeIntervalInSeconds | RO | ||||||||||||||||||
scalar · TimeIntervalInSeconds · read-only · current If automatic characterization is enabled and all conditions for a characterization are met, this will indicate the remaining time until the automatic characterization discharge will start.
| |||||||||||||||||||||
| Sbtr-Characterize-Battery | 1.3.6.1.4.1.1918.2.13.10.100.60.90 | No_Data | RW | ||||||||||||||||||
scalar · No_Data · read-write · current This will cause the controller to discharge the battery at a constant rate until the average cell discharge voltage reaches the configured end voltage. | |||||||||||||||||||||
| Sbtr-Stop-Battery-Characterization | 1.3.6.1.4.1.1918.2.13.10.100.60.100 | No_Data | RW | ||||||||||||||||||
scalar · No_Data · read-write · current Stops the current battery characterization discharge. | |||||||||||||||||||||
| Sbtr-Cancel-Waiting | 1.3.6.1.4.1.1918.2.13.10.100.60.105 | No_Data | RW | ||||||||||||||||||
scalar · No_Data · read-write · current Cancel the waiting period, returning the LVDs to automatic operation. | |||||||||||||||||||||
| Sbtr-Clear-Battery-Characterization | 1.3.6.1.4.1.1918.2.13.10.100.60.110 | No_Data | RW | ||||||||||||||||||
scalar · No_Data · read-write · current Clears the battery characterization data. It is recommended to make a backup of the characterization data first. | |||||||||||||||||||||
| Nalarms | 1.3.6.1.4.1.1918.2.13.10.110 | ||||||||||||||||||||
| Nalarm-States | 1.3.6.1.4.1.1918.2.13.10.110.5 | ||||||||||||||||||||
| Ssummary-Alarm-Critical | 1.3.6.1.4.1.1918.2.13.10.110.5.10 | Boolean | RO | 0 | |||||||||||||||||
scalar · Boolean · read-only · current Active if any critical alarm is active. Example values from LibreNMS test devices
| |||||||||||||||||||||
| Ssummary-Alarm-Major | 1.3.6.1.4.1.1918.2.13.10.110.5.20 | Boolean | RO | 0 | |||||||||||||||||
scalar · Boolean · read-only · current Active if any major alarm is active. Example values from LibreNMS test devices
| |||||||||||||||||||||
| Ssummary-Alarm-Minor | 1.3.6.1.4.1.1918.2.13.10.110.5.30 | Boolean | RO | 0 | |||||||||||||||||
scalar · Boolean · read-only · current Active if any minor alarm is active. Example values from LibreNMS test devices
| |||||||||||||||||||||
| Sreset-Battery-Test-Failed-Alarm | 1.3.6.1.4.1.1918.2.13.10.110.5.100 | No_Data | RW | ||||||||||||||||||
scalar · No_Data · read-write · current This command attempts to reset Battery Test Failed alarm. | |||||||||||||||||||||
| Sreset-Rectifier-Comms-Lost-Alarm | 1.3.6.1.4.1.1918.2.13.10.110.5.110 | No_Data | RW | ||||||||||||||||||
scalar · No_Data · read-write · current This command attempts to reset Rectifier Comms Lost alarm and Multiple Rect Comms Lost alarm. | |||||||||||||||||||||
| Talarm-Table | 1.3.6.1.4.1.1918.2.13.10.110.10 | NA | |||||||||||||||||||
| Ralarm-Entry | 1.3.6.1.4.1.1918.2.13.10.110.10.1 | NA | |||||||||||||||||||
row · not-accessible · current
| |||||||||||||||||||||
| Calarm-Index | 1.3.6.1.4.1.1918.2.13.10.110.10.1.1 | System_Alarm | RO | ||||||||||||||||||
column · System_Alarm · read-only · current Automatically generated index object. | |||||||||||||||||||||
| Calarm-Name | 1.3.6.1.4.1.1918.2.13.10.110.10.1.20 | Display_40 | RO | ||||||||||||||||||
column · Display_40 · read-only · current The name of the Alarm. | |||||||||||||||||||||
| Calarm-Severity | 1.3.6.1.4.1.1918.2.13.10.110.10.1.31 | Alarm_Severity | RW | ||||||||||||||||||
column · Alarm_Severity · read-write · current The severity level associated with the alarm. Control alarms are not displayed, although any configured digital outputs are still activated. | |||||||||||||||||||||
| Calarm-State | 1.3.6.1.4.1.1918.2.13.10.110.10.1.40 | Alarm_Active_State | RO | ||||||||||||||||||
column · Alarm_Active_State · read-only · current The state of this alarm. | |||||||||||||||||||||
| Calarm-Notes | 1.3.6.1.4.1.1918.2.13.10.110.10.1.50 | Display_60 | RW | ||||||||||||||||||
column · Display_60 · read-write · current User notes about this alarm. These notes appear in SNMP traps and can be viewed using DCTools or PowerManagerII. | |||||||||||||||||||||
| Nalarm-Configuration | 1.3.6.1.4.1.1918.2.13.10.110.15 | ||||||||||||||||||||
| Senable-Audible-Alarm-Indication | 1.3.6.1.4.1.1918.2.13.10.110.15.10 | Enable_State | RW | ||||||||||||||||||
scalar · Enable_State · read-write · current Enable/disable audible alarm indication. | |||||||||||||||||||||
| Salarm-Recognition-Period | 1.3.6.1.4.1.1918.2.13.10.110.15.20 | TimeIntervalInSeconds | RW | ||||||||||||||||||
scalar · TimeIntervalInSeconds · read-write · current An alarm condition must be continuously active for this period before an alarm is generated.
| |||||||||||||||||||||
| Sac-Fail-Recognition-Period | 1.3.6.1.4.1.1918.2.13.10.110.15.30 | TimeIntervalInSeconds | RW | ||||||||||||||||||
scalar · TimeIntervalInSeconds · read-write · current An AC fail condition must be continuously active for this period before an AC Fail alarm is generated.
| |||||||||||||||||||||
| Senable-High-Float-Tracking | 1.3.6.1.4.1.1918.2.13.10.110.15.40 | Enable_State | RW | ||||||||||||||||||
scalar · Enable_State · read-write · current The alarm thresholds will be increased when the operating voltage is raised by a voltage control function. | |||||||||||||||||||||
| Shigh-Float-Threshold | 1.3.6.1.4.1.1918.2.13.10.110.15.50 | Float | RW | ||||||||||||||||||
scalar · Float · read-write · current High Float alarm is activated if the bus voltage is above this value.
| |||||||||||||||||||||
| Senable-Low-Float-Tracking | 1.3.6.1.4.1.1918.2.13.10.110.15.60 | Enable_State | RW | ||||||||||||||||||
scalar · Enable_State · read-write · current The alarm thresholds will be reduced when the operating voltage is lowered by a voltage control function. | |||||||||||||||||||||
| Slow-Float-Threshold | 1.3.6.1.4.1.1918.2.13.10.110.15.70 | Float | RW | ||||||||||||||||||
scalar · Float · read-write · current Low Float alarm is activated when the bus voltage is below this value.
| |||||||||||||||||||||
| Shigh-Load-Threshold | 1.3.6.1.4.1.1918.2.13.10.110.15.80 | Float | RW | ||||||||||||||||||
scalar · Float · read-write · current High Load alarm is activated if the bus voltage is above this value.
| |||||||||||||||||||||
| Slow-Load-Threshold | 1.3.6.1.4.1.1918.2.13.10.110.15.90 | Float | RW | ||||||||||||||||||
scalar · Float · read-write · current The Low Load alarm is activated if the bus voltage is below this value.
| |||||||||||||||||||||
| Sbattery-Temperature-High-Threshold | 1.3.6.1.4.1.1918.2.13.10.110.15.130 | Signed8 | RW | ||||||||||||||||||
scalar · Signed8 · read-write · current Battery Temperature High alarm is activated if the battery temperature is above this value.
| |||||||||||||||||||||
| Sbattery-Temperature-Low-Threshold | 1.3.6.1.4.1.1918.2.13.10.110.15.140 | Signed8 | RW | ||||||||||||||||||
scalar · Signed8 · read-write · current Battery Temperature Low alarm is activated if the battery temperature is below this value.
| |||||||||||||||||||||
| Ssystem-Overload-Type | 1.3.6.1.4.1.1918.2.13.10.110.15.170 | Overload_Alarm_Type | RW | ||||||||||||||||||
scalar · Overload_Alarm_Type · read-write · current The controller can detect a system overload either based on a simple load threshold or based on a redundancy calculation taking into account individual rectifier capacities. | |||||||||||||||||||||
| Ssystem-Overload-Recognition-Period | 1.3.6.1.4.1.1918.2.13.10.110.15.180 | TimeIntervalInMinutes | RW | ||||||||||||||||||
scalar · TimeIntervalInMinutes · read-write · current The System Overload alarm activates if the condition (see System Overload Type) has been continuously true for this time. It is normally set to several hours so that the alarm does not operate during a normal battery recharge.
| |||||||||||||||||||||
| Ssystem-Overload-Threshold | 1.3.6.1.4.1.1918.2.13.10.110.15.190 | Unsigned8 | RW | ||||||||||||||||||
scalar · Unsigned8 · read-write · current The System Overload alarm activates if the load is above this threshold continuously for the System Overload Recognition Period. Measured as a percentage of total rectifier capacity.
| |||||||||||||||||||||
| Sin-Discharge-Alarm-Condition | 1.3.6.1.4.1.1918.2.13.10.110.15.200 | In_Discharge_Alarm_Condition | RW | ||||||||||||||||||
scalar · In_Discharge_Alarm_Condition · read-write · current This specifies if AC present is required for In Discharge alarm to be active. | |||||||||||||||||||||
| Sbattery-Current-Sensor-Fail-Recognition-Period | 1.3.6.1.4.1.1918.2.13.10.110.15.220 | TimeIntervalInSeconds | RW | ||||||||||||||||||
scalar · TimeIntervalInSeconds · read-write · current If the battery current sensor continuously does not report a valid current for this time, the battery current sensor will be considered failed.
| |||||||||||||||||||||
| Tsmart-Alarm-Table | 1.3.6.1.4.1.1918.2.13.10.110.20 | NA | |||||||||||||||||||
| Rsmart-Alarm-Entry | 1.3.6.1.4.1.1918.2.13.10.110.20.1 | NA | |||||||||||||||||||
row · not-accessible · current
| |||||||||||||||||||||
| Csmart-Alarm-Index | 1.3.6.1.4.1.1918.2.13.10.110.20.1.1 | Unsigned8 | RO | ||||||||||||||||||
column · Unsigned8 · read-only · current Automatically generated index object. | |||||||||||||||||||||
| Csmart-Alarm-Send-Trap | 1.3.6.1.4.1.1918.2.13.10.110.20.1.10 | Boolean | RW | ||||||||||||||||||
column · Boolean · read-write · current If set to true an SNMP trap is sent to every trap receiver with an appropriate trap level whenever this alarm changes state. | |||||||||||||||||||||
| Csmart-Alarm-Name | 1.3.6.1.4.1.1918.2.13.10.110.20.1.20 | Display_20 | RW | ||||||||||||||||||
column · Display_20 · read-write · current Alarm name. | |||||||||||||||||||||
| Csmart-Alarm-Severity | 1.3.6.1.4.1.1918.2.13.10.110.20.1.30 | Alarm_Severity | RW | ||||||||||||||||||
column · Alarm_Severity · read-write · current The severity level associated with the alarm. Control alarms are not displayed, although any configured digital outputs are still activated. | |||||||||||||||||||||
| Csmart-Alarm-Group | 1.3.6.1.4.1.1918.2.13.10.110.20.1.35 | Unsigned8 | RW | ||||||||||||||||||
column · Unsigned8 · read-write · current The group number used by SiteManager. The group only affects the display of this item in SiteManager. It does not affect controller operation. | |||||||||||||||||||||
| Csmart-Alarm-Notes | 1.3.6.1.4.1.1918.2.13.10.110.20.1.40 | Display_60 | RW | ||||||||||||||||||
column · Display_60 · read-write · current User notes about this alarm. | |||||||||||||||||||||
| Csmart-Alarm-Operator | 1.3.6.1.4.1.1918.2.13.10.110.20.1.50 | Alarm_Operator | RW | ||||||||||||||||||
column · Alarm_Operator · read-write · current The logic operator used to combine the states of all sources mapped to this smart alarm. | |||||||||||||||||||||
| Csmart-Alarm-Recognition-Period | 1.3.6.1.4.1.1918.2.13.10.110.20.1.60 | TimeIntervalInSeconds | RW | ||||||||||||||||||
column · TimeIntervalInSeconds · read-write · current A smart alarm will become active if the logic for this alarm is continuously true for the recognition time.
| |||||||||||||||||||||
| Csmart-Alarm-Deactivation-Recognition-Period | 1.3.6.1.4.1.1918.2.13.10.110.20.1.61 | TimeIntervalInSeconds | RW | ||||||||||||||||||
column · TimeIntervalInSeconds · read-write · current A smart alarm will deactivate if the logic for this alarm is continuously false for the deactivation recognition time.
| |||||||||||||||||||||
| Csmart-Alarm-DO-Mapping-A | 1.3.6.1.4.1.1918.2.13.10.110.20.1.70 | Relay_Mapping | RW | ||||||||||||||||||
column · Relay_Mapping · read-write · current Optional digital output activated while this alarm is active. | |||||||||||||||||||||
| Csmart-Alarm-DO-Mapping-B | 1.3.6.1.4.1.1918.2.13.10.110.20.1.80 | Relay_Mapping | RW | ||||||||||||||||||
column · Relay_Mapping · read-write · current Optional digital output activated while this alarm is active. | |||||||||||||||||||||
| Csmart-Alarm-State | 1.3.6.1.4.1.1918.2.13.10.110.20.1.100 | Alarm_Active_State | RO | ||||||||||||||||||
column · Alarm_Active_State · read-only · current The state of this alarm. | |||||||||||||||||||||
| Cclear-Smart-Alarm | 1.3.6.1.4.1.1918.2.13.10.110.20.1.110 | No_Data | RW | ||||||||||||||||||
column · No_Data · read-write · current This will temporarily override the alarm logic and force the alarm to deactivate. If this does not cause the trigger conditions for the alarm to change (for instance through a circular dependency), the alarm will reactivate after its recognition time. | |||||||||||||||||||||
| Tsource-Alarm-Table | 1.3.6.1.4.1.1918.2.13.10.110.30 | NA | |||||||||||||||||||
| Rsource-Alarm-Entry | 1.3.6.1.4.1.1918.2.13.10.110.30.1 | NA | |||||||||||||||||||
row · not-accessible · current
| |||||||||||||||||||||
| Csource-Alarm-Index | 1.3.6.1.4.1.1918.2.13.10.110.30.1.1 | Unsigned8 | RO | ||||||||||||||||||
column · Unsigned8 · read-only · current Automatically generated index object. | |||||||||||||||||||||
| Csmart-Alarm-Alarm-Source-Trigger-State | 1.3.6.1.4.1.1918.2.13.10.110.30.1.10 | Trigger_State | RO | ||||||||||||||||||
column · Trigger_State · read-only · current Indicates the trigger state of this source alarm. | |||||||||||||||||||||
| Csmart-Alarm-Alarm-Source-Status | 1.3.6.1.4.1.1918.2.13.10.110.30.1.20 | Enable_State | RW | ||||||||||||||||||
column · Enable_State · read-write · current Enable or disable this smart alarm source. | |||||||||||||||||||||
| Csmart-Alarm-Alarm-Source-Mapping | 1.3.6.1.4.1.1918.2.13.10.110.30.1.30 | Unsigned8 | RW | ||||||||||||||||||
column · Unsigned8 · read-write · current Index of smart alarm that this source is mapped to. | |||||||||||||||||||||
| Csmart-Alarm-Alarm-Source-Logic | 1.3.6.1.4.1.1918.2.13.10.110.30.1.40 | Source_Alarm_Logic | RW | ||||||||||||||||||
column · Source_Alarm_Logic · read-write · current Optionally negates the state of the source alarm as an input to the smart alarm. | |||||||||||||||||||||
| Csmart-Alarm-Alarm-Source-Trigger | 1.3.6.1.4.1.1918.2.13.10.110.30.1.41 | Source_Trigger | RW | ||||||||||||||||||
column · Source_Trigger · read-write · current Determines whether the source alarm's recognition time (if any) is taken into account. If the source alarm is itself a smart alarm and the sources of one or more smart alarms form a cyclic dependency, then at least one of these sources must be configured to trigger when its source is active. Such cyclic dependencies can be used to build complex logical functions such as an astable flip-flop using the source's recognition times as delays. | |||||||||||||||||||||
| Csmart-Alarm-Alarm-Source-Type | 1.3.6.1.4.1.1918.2.13.10.110.30.1.50 | Alarm_Type | RW | ||||||||||||||||||
column · Alarm_Type · read-write · current The alarm table this source alarm is taken from. | |||||||||||||||||||||
| Csmart-Alarm-Alarm-Source-Index | 1.3.6.1.4.1.1918.2.13.10.110.30.1.60 | Unsigned8 | RW | ||||||||||||||||||
column · Unsigned8 · read-write · current The index of the source alarm. | |||||||||||||||||||||
| Tsource-Schedule-Table | 1.3.6.1.4.1.1918.2.13.10.110.40 | NA | |||||||||||||||||||
| Rsource-Schedule-Entry | 1.3.6.1.4.1.1918.2.13.10.110.40.1 | NA | |||||||||||||||||||
row · not-accessible · current | |||||||||||||||||||||
| Csource-Schedule-Index | 1.3.6.1.4.1.1918.2.13.10.110.40.1.1 | Unsigned8 | RO | ||||||||||||||||||
column · Unsigned8 · read-only · current Automatically generated index object. | |||||||||||||||||||||
| Csmart-Alarm-Schedule-Source-Is-Triggered | 1.3.6.1.4.1.1918.2.13.10.110.40.1.10 | Boolean | RO | ||||||||||||||||||
column · Boolean · read-only · current Indicates whether or not this schedule is currently considered true or false. | |||||||||||||||||||||
| Csmart-Alarm-Schedule-Source-Status | 1.3.6.1.4.1.1918.2.13.10.110.40.1.20 | Enable_State | RW | ||||||||||||||||||
column · Enable_State · read-write · current Enable or disable this smart alarm schedule. | |||||||||||||||||||||
| Csmart-Alarm-Schedule-Source-Mapping | 1.3.6.1.4.1.1918.2.13.10.110.40.1.30 | Unsigned8 | RW | ||||||||||||||||||
column · Unsigned8 · read-write · current Index of smart alarm that this schedule is mapped to. | |||||||||||||||||||||
| Csmart-Alarm-Schedule-Source-First-Activation | 1.3.6.1.4.1.1918.2.13.10.110.40.1.50 | Julian_Time_UTC_25 | RO | ||||||||||||||||||
column · Julian_Time_UTC_25 · read-only · current The date and time at which this schedule will activate for the first time. | |||||||||||||||||||||
| Csmart-Alarm-Schedule-Source-Duration | 1.3.6.1.4.1.1918.2.13.10.110.40.1.60 | TimeIntervalInMinutes | RW | ||||||||||||||||||
column · TimeIntervalInMinutes · read-write · current This source will become active every Interval after the First Activation and remain active for Duration each time.
| |||||||||||||||||||||
| Csmart-Alarm-Schedule-Source-Interval | 1.3.6.1.4.1.1918.2.13.10.110.40.1.70 | TimeIntervalInMinutes | RW | ||||||||||||||||||
column · TimeIntervalInMinutes · read-write · current This source will become active every Interval after the First Activation and remain active for Duration each time.
| |||||||||||||||||||||
| Csmart-Alarm-Schedule-Source-Repetitions | 1.3.6.1.4.1.1918.2.13.10.110.40.1.80 | Counter32 | RW | ||||||||||||||||||
column · Counter32 · read-write · current The number of times this schedule should activate. After the last activation period, this schedule will remain inactive indefinitely. If set to zero, there is no limit on the number of activations. | |||||||||||||||||||||
| Csmart-Alarm-Schedule-Source-Next | 1.3.6.1.4.1.1918.2.13.10.110.40.1.90 | Julian_Time_UTC_25 | RO | ||||||||||||||||||
column · Julian_Time_UTC_25 · read-only · current The date and time at which this schedule will activate next. | |||||||||||||||||||||
| Csmart-Alarm-Schedule-Source-End | 1.3.6.1.4.1.1918.2.13.10.110.40.1.100 | Julian_Time_UTC_25 | RO | ||||||||||||||||||
column · Julian_Time_UTC_25 · read-only · current The date and time at which this schedule will deactivate for the last time. | |||||||||||||||||||||
| Tsystem-Value-Source-Table | 1.3.6.1.4.1.1918.2.13.10.110.50 | NA | |||||||||||||||||||
| Rsystem-Value-Source-Entry | 1.3.6.1.4.1.1918.2.13.10.110.50.1 | NA | |||||||||||||||||||
row · not-accessible · current | |||||||||||||||||||||
| Csystem-Value-Source-Index | 1.3.6.1.4.1.1918.2.13.10.110.50.1.1 | Unsigned8 | RO | ||||||||||||||||||
column · Unsigned8 · read-only · current Automatically generated index object. | |||||||||||||||||||||
| Csmart-Alarm-System-Value-Source-Is-Triggered | 1.3.6.1.4.1.1918.2.13.10.110.50.1.10 | Boolean | RO | ||||||||||||||||||
column · Boolean · read-only · current Indicates whether or not this analog source is currently considered true or false. | |||||||||||||||||||||
| Csmart-Alarm-System-Value-Source-Status | 1.3.6.1.4.1.1918.2.13.10.110.50.1.20 | Enable_State | RW | ||||||||||||||||||
column · Enable_State · read-write · current Enable or disable this smart alarm analog source. | |||||||||||||||||||||
| Csmart-Alarm-System-Value-Source-Mapping | 1.3.6.1.4.1.1918.2.13.10.110.50.1.30 | Unsigned8 | RW | ||||||||||||||||||
column · Unsigned8 · read-write · current Index of smart alarm that this analog source is mapped to. | |||||||||||||||||||||
| Csmart-Alarm-System-Value-Source-Value | 1.3.6.1.4.1.1918.2.13.10.110.50.1.40 | System_Value_Source_Value | RW | ||||||||||||||||||
column · System_Value_Source_Value · read-write · current The system value that is compared with the threshold. | |||||||||||||||||||||
| Csmart-Alarm-System-Value-Source-Input | 1.3.6.1.4.1.1918.2.13.10.110.50.1.45 | Float | RO | ||||||||||||||||||
column · Float · read-only · current Shows the actual value of the selected system value that is compared against the threshold.
| |||||||||||||||||||||
| Csmart-Alarm-System-Value-Source-Threshold-Type | 1.3.6.1.4.1.1918.2.13.10.110.50.1.50 | Threshold_Type | RW | ||||||||||||||||||
column · Threshold_Type · read-write · current Determines whether the threshold is an upper or lower threshold to the system value. | |||||||||||||||||||||
| Csmart-Alarm-System-Value-Source-Threshold | 1.3.6.1.4.1.1918.2.13.10.110.50.1.60 | Float | RW | ||||||||||||||||||
column · Float · read-write · current The threshold, the system value is compared to.
| |||||||||||||||||||||
| Csmart-Alarm-System-Value-Source-Hysteresis | 1.3.6.1.4.1.1918.2.13.10.110.50.1.70 | Float | RW | ||||||||||||||||||
column · Float · read-write · current If non-zero, the system value must exceed the threshold +/- this value before the source becomes false again.
| |||||||||||||||||||||
| Tsource-Manual-Table | 1.3.6.1.4.1.1918.2.13.10.110.60 | NA | |||||||||||||||||||
| Rsource-Manual-Entry | 1.3.6.1.4.1.1918.2.13.10.110.60.1 | NA | |||||||||||||||||||
row · not-accessible · current
| |||||||||||||||||||||
| Csource-Manual-Index | 1.3.6.1.4.1.1918.2.13.10.110.60.1.1 | Unsigned8 | RO | ||||||||||||||||||
column · Unsigned8 · read-only · current Automatically generated index object. | |||||||||||||||||||||
| Csmart-Alarm-Is-Manual-Source-Triggered | 1.3.6.1.4.1.1918.2.13.10.110.60.1.10 | Boolean | RO | ||||||||||||||||||
column · Boolean · read-only · current Indicates whether or not this manual source is currently considered true or false. | |||||||||||||||||||||
| Csmart-Alarm-Source-Manual-Status | 1.3.6.1.4.1.1918.2.13.10.110.60.1.20 | Enable_State | RW | ||||||||||||||||||
column · Enable_State · read-write · current Enable or disable this smart alarm manual. | |||||||||||||||||||||
| Csmart-Alarm-Source-Manual-Trigger | 1.3.6.1.4.1.1918.2.13.10.110.60.1.30 | Boolean | RW | ||||||||||||||||||
column · Boolean · read-write · current Trigger input for this manual Alarm. | |||||||||||||||||||||
| Csmart-Alarm-Source-Manual-Mapping | 1.3.6.1.4.1.1918.2.13.10.110.60.1.40 | Unsigned8 | RW | ||||||||||||||||||
column · Unsigned8 · read-write · current Index of smart alarm that this manual is mapped to. | |||||||||||||||||||||
| Csmart-Alarm-Source-Manual-Logic | 1.3.6.1.4.1.1918.2.13.10.110.60.1.50 | Source_Alarm_Logic | RW | ||||||||||||||||||
column · Source_Alarm_Logic · read-write · current Optionally negates the state of the source as an input to the smart alarm. | |||||||||||||||||||||
| Nglobal-Alarms | 1.3.6.1.4.1.1918.2.13.10.111 | ||||||||||||||||||||
| Strap-Alarm-Origin | 1.3.6.1.4.1.1918.2.13.10.111.10 | Alarm_Type | RO | ||||||||||||||||||
scalar · Alarm_Type · read-only · current The origin of the alarm. This is sent with the SNMP trap. | |||||||||||||||||||||
| Strap-Alarm-Name | 1.3.6.1.4.1.1918.2.13.10.111.11 | Display_40 | RO | ||||||||||||||||||
scalar · Display_40 · read-only · current The name of the Alarm. This is sent with the SNMP trap. | |||||||||||||||||||||
| Strap-Alarm-Number | 1.3.6.1.4.1.1918.2.13.10.111.12 | Unsigned16 | RO | ||||||||||||||||||
scalar · Unsigned16 · read-only · current The number for this Alarm. This is sent with the SNMP trap. | |||||||||||||||||||||
| Strap-Additional-Text | 1.3.6.1.4.1.1918.2.13.10.111.13 | Display_60 | RO | ||||||||||||||||||
scalar · Display_60 · read-only · current User notes about this alarm. These notes appear in SNMP traps and can be viewed using DCTools or PowerManagerII. | |||||||||||||||||||||
| Strap-Alarm-Keep-Severity | 1.3.6.1.4.1.1918.2.13.10.111.14 | Trap_Alarm_Keep_Severity | RO | ||||||||||||||||||
scalar · Trap_Alarm_Keep_Severity · read-only · current The severity of the alarm. This is sent with the SNMP trap. | |||||||||||||||||||||
| Nrps-Traps | 1.3.6.1.4.1.1918.2.13.20 | ||||||||||||||||||||
| !major-Alarm-Active | 1.3.6.1.4.1.1918.2.13.20.100 | ||||||||||||||||||||
notification · current A major alarm is active.
| |||||||||||||||||||||
| !major-AI-High-Active | 1.3.6.1.4.1.1918.2.13.20.101 | ||||||||||||||||||||
notification · current A major analog input high alarm is active. | |||||||||||||||||||||
| !major-AI-Low-Active | 1.3.6.1.4.1.1918.2.13.20.102 | ||||||||||||||||||||
notification · current A major analog input low alarm is active. | |||||||||||||||||||||
| !major-DI-Active | 1.3.6.1.4.1.1918.2.13.20.103 | ||||||||||||||||||||
notification · current A major digital input alarm is active. | |||||||||||||||||||||
| !major-Smart-Active | 1.3.6.1.4.1.1918.2.13.20.104 | ||||||||||||||||||||
notification · current A major smart alarm is active. | |||||||||||||||||||||
| !minor-Alarm-Active | 1.3.6.1.4.1.1918.2.13.20.200 | ||||||||||||||||||||
notification · current A minor alarm is active.
| |||||||||||||||||||||
| !minor-AI-High-Active | 1.3.6.1.4.1.1918.2.13.20.201 | ||||||||||||||||||||
notification · current A minor analog input high alarm is active. | |||||||||||||||||||||
| !minor-AI-Low-Active | 1.3.6.1.4.1.1918.2.13.20.202 | ||||||||||||||||||||
notification · current A minor analog input low alarm is active. | |||||||||||||||||||||
| !minor-DI-Active | 1.3.6.1.4.1.1918.2.13.20.203 | ||||||||||||||||||||
notification · current A minor digital input alarm is active. | |||||||||||||||||||||
| !minor-Smart-Active | 1.3.6.1.4.1.1918.2.13.20.204 | ||||||||||||||||||||
notification · current A minor smart alarm is active. | |||||||||||||||||||||
| !warning-Alarm-Active | 1.3.6.1.4.1.1918.2.13.20.300 | ||||||||||||||||||||
notification · current A warning is active.
| |||||||||||||||||||||
| !warning-AI-High-Active | 1.3.6.1.4.1.1918.2.13.20.301 | ||||||||||||||||||||
notification · current An analog input high warning is active. | |||||||||||||||||||||
| !warning-AI-Low-Active | 1.3.6.1.4.1.1918.2.13.20.302 | ||||||||||||||||||||
notification · current An analog input low warning is active. | |||||||||||||||||||||
| !warning-DI-Active | 1.3.6.1.4.1.1918.2.13.20.303 | ||||||||||||||||||||
notification · current A digital input warning is active. | |||||||||||||||||||||
| !warning-Smart-Active | 1.3.6.1.4.1.1918.2.13.20.304 | ||||||||||||||||||||
notification · current A smart warning is active. | |||||||||||||||||||||
| !alarm-Inactive | 1.3.6.1.4.1.1918.2.13.20.400 | ||||||||||||||||||||
notification · current An alarm has become inactive.
| |||||||||||||||||||||
| !ai-High-Inactive | 1.3.6.1.4.1.1918.2.13.20.401 | ||||||||||||||||||||
notification · current An analog input high alarm has become inactive. | |||||||||||||||||||||
| !ai-Low-Inactive | 1.3.6.1.4.1.1918.2.13.20.402 | ||||||||||||||||||||
notification · current An analog input low alarm has become inactive. | |||||||||||||||||||||
| !di-Inactive | 1.3.6.1.4.1.1918.2.13.20.403 | ||||||||||||||||||||
notification · current A digital input alarm has become inactive. | |||||||||||||||||||||
| !smart-Inactive | 1.3.6.1.4.1.1918.2.13.20.404 | ||||||||||||||||||||
notification · current A smart alarm has become inactive. | |||||||||||||||||||||
| !alarm-Status-Change | 1.3.6.1.4.1.1918.2.13.20.500 | ||||||||||||||||||||
notification · current The status of one or more alarms has changed. | |||||||||||||||||||||
| !critical-Alarm-Active | 1.3.6.1.4.1.1918.2.13.20.600 | ||||||||||||||||||||
notification · current A critical alarm is active.
| |||||||||||||||||||||
| !critical-AI-High-Active | 1.3.6.1.4.1.1918.2.13.20.601 | ||||||||||||||||||||
notification · current A critical analog input high alarm is active. | |||||||||||||||||||||
| !critical-AI-Low-Active | 1.3.6.1.4.1.1918.2.13.20.602 | ||||||||||||||||||||
notification · current A critical analog input low alarm is active. | |||||||||||||||||||||
| !critical-DI-Active | 1.3.6.1.4.1.1918.2.13.20.603 | ||||||||||||||||||||
notification · current A critical digital input alarm is active. | |||||||||||||||||||||
| !critical-Smart-Active | 1.3.6.1.4.1.1918.2.13.20.604 | ||||||||||||||||||||
notification · current A critical smart alarm is active. | |||||||||||||||||||||
| !global | 1.3.6.1.4.1.1918.2.13.20.700 | ||||||||||||||||||||
notification · current An alarm has changed state. | |||||||||||||||||||||
Textual conventions
BooleanINTEGERfalse(0)true(1)FloatInteger32 (-2147483648..2147483647)Julian-Date-UTCOCTET STRING (SIZE (0..25))Display hint:
25tJulian-Time-UTCOCTET STRING (SIZE (0..25))Display hint:
25tMIB-Object-IDOCTET STRING (SIZE (0..80))Display hint:
80tNo-DataOCTET STRING (SIZE (0))Signed16Integer32 (-32768..32767)Signed32Integer32 (-2147483648..2147483647)Signed8Integer32 (-128..127)String-10OCTET STRING (SIZE (0..10))Display hint:
10tString-17OCTET STRING (SIZE (0..17))Display hint:
17tString-20OCTET STRING (SIZE (0..20))Display hint:
20tString-200OCTET STRING (SIZE (0..200))Display hint:
200tString-253OCTET STRING (SIZE (0..253))Display hint:
253tString-30OCTET STRING (SIZE (0..30))Display hint:
30tString-32OCTET STRING (SIZE (0..32))Display hint:
32tString-40OCTET STRING (SIZE (0..40))Display hint:
40tString-60OCTET STRING (SIZE (0..60))Display hint:
60tString-64OCTET STRING (SIZE (0..64))Display hint:
64tUnsigned16Integer32 (0..65535)Unsigned31Integer32 (0..2147483646)Unsigned8Integer32 (0..255)UnsignedNAN16INTEGERnotAvailable(65535)UnsignedNAN32Counter32UnsignedNAN8INTEGERnotAvailable(255)
Traps / Notifications
- global
1.3.6.1.4.1.1918.2.13.20.700 - ai-High-Inactive
1.3.6.1.4.1.1918.2.13.20.401 - ai-Low-Inactive
1.3.6.1.4.1.1918.2.13.20.402 - alarm-Inactive
1.3.6.1.4.1.1918.2.13.20.400 - alarm-Status-Change
1.3.6.1.4.1.1918.2.13.20.500 - critical-AI-High-Active
1.3.6.1.4.1.1918.2.13.20.601 - critical-AI-Low-Active
1.3.6.1.4.1.1918.2.13.20.602 - critical-Alarm-Active
1.3.6.1.4.1.1918.2.13.20.600 - critical-DI-Active
1.3.6.1.4.1.1918.2.13.20.603 - critical-Smart-Active
1.3.6.1.4.1.1918.2.13.20.604 - di-Inactive
1.3.6.1.4.1.1918.2.13.20.403 - major-AI-High-Active
1.3.6.1.4.1.1918.2.13.20.101 - major-AI-Low-Active
1.3.6.1.4.1.1918.2.13.20.102 - major-Alarm-Active
1.3.6.1.4.1.1918.2.13.20.100 - major-DI-Active
1.3.6.1.4.1.1918.2.13.20.103 - major-Smart-Active
1.3.6.1.4.1.1918.2.13.20.104 - minor-AI-High-Active
1.3.6.1.4.1.1918.2.13.20.201 - minor-AI-Low-Active
1.3.6.1.4.1.1918.2.13.20.202 - minor-Alarm-Active
1.3.6.1.4.1.1918.2.13.20.200 - minor-DI-Active
1.3.6.1.4.1.1918.2.13.20.203 - minor-Smart-Active
1.3.6.1.4.1.1918.2.13.20.204 - smart-Inactive
1.3.6.1.4.1.1918.2.13.20.404 - warning-AI-High-Active
1.3.6.1.4.1.1918.2.13.20.301 - warning-AI-Low-Active
1.3.6.1.4.1.1918.2.13.20.302 - warning-Alarm-Active
1.3.6.1.4.1.1918.2.13.20.300 - warning-DI-Active
1.3.6.1.4.1.1918.2.13.20.303 - warning-Smart-Active
1.3.6.1.4.1.1918.2.13.20.304