HORIZON-ODU-MIB
Standards (IETF)snmptranslate -m HORIZON-ODU-MIB -Tpsnmpwalk -v2c -c <community> -m HORIZON-ODU-MIB <host> 1.3.6.1.2.1.11.0.0Imports
| HORIZON-MIB | horizon |
|---|---|
| IF-MIB | OBJECT-TYPE, ifIndex |
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP |
| SNMPv2-MIB | snmp |
| SNMPv2-SMI | Bits, Counter32, Gauge32, Integer32, IpAddress, MODULE-IDENTITY, MibIdentifier, OBJECT-IDENTITY, OBJECT-TYPE, TRAP-TYPE, TimeTicks, Unsigned32, iso |
| SNMPv2-TC | DisplayString, PhysAddress, TEXTUAL-CONVENTION |
OID tree
| Name | OID | Type | Access | Status | Example | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| !coldStart | 1.3.6.1.2.1.11.0.0 | ||||||||||||
notification A coldStart trap signifies that the sending protocol entity is reinitializing itself such that the agent's configuration or the protocol entity implementation may be altered. | |||||||||||||
| !linkDown | 1.3.6.1.2.1.11.0.1 | ||||||||||||
notification A linkDown trap signifies that the sending protocol entity recognizes a failure in one of the communication links represented in the agent's configuration.
| |||||||||||||
| !linkUp | 1.3.6.1.2.1.11.0.2 | ||||||||||||
notification A linkUp trap signifies that the sending protocol entity recognizes that one of the communication links represented in the agent's configuration has come up.
| |||||||||||||
| NhorizonOdu | 1.3.6.1.4.1.7262.2.2 | ||||||||||||
| NhzOduSystem | 1.3.6.1.4.1.7262.2.2.1 | ||||||||||||
| NhzOduSysGeneral | 1.3.6.1.4.1.7262.2.2.1.1 | ||||||||||||
| ShzOduResetSystem | 1.3.6.1.4.1.7262.2.2.1.1.1 | INTEGER (0..1) | WO | mandatory | |||||||||
scalar · INTEGER (0..1) · write-only · mandatory Writing '1' to this object resets the NIC, Modem, and radio. | |||||||||||||
| ShzOduSaveMIB | 1.3.6.1.4.1.7262.2.2.1.1.2 | INTEGER | WO | mandatory | |||||||||
scalar · INTEGER · write-only · mandatory Writing '1' to this object save all MIB values. Note: If the horizon type is 'apng120' or 'apng170' and the radio band doesn't match the horizon type, Mib can't be saved.
| |||||||||||||
| ShzOduOperStatus | 1.3.6.1.4.1.7262.2.2.1.1.3 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory The current operational state of the system. Testing indicates that no operational packets can be passed.
| |||||||||||||
| ShzOduAirInterfaceEncryption | 1.3.6.1.4.1.7262.2.2.1.1.4 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory OBSOLETE. This enables encryption on the air interface.
| |||||||||||||
| ShzOduSystemRedundancy | 1.3.6.1.4.1.7262.2.2.1.1.5 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory Sets system redundancy on/off. If there are any radio failures then the system will automatically switch to redundant system.
| |||||||||||||
| NhzOduSysSpeed | 1.3.6.1.4.1.7262.2.2.1.2 | ||||||||||||
| ShzOduSystemCurrentSpeed | 1.3.6.1.4.1.7262.2.2.1.2.1 | INTEGER (0..1000) | RW | mandatory | |||||||||
scalar · INTEGER (0..1000) · read-write · mandatory Changes the working speed of the horizon.
Writes are only valid if system is a FLEX. Due to backwards compatibility issue, 0 value should
be treated as 0 Mbps. | |||||||||||||
| ShzOduSystemLicensedSpeed | 1.3.6.1.4.1.7262.2.2.1.2.2 | INTEGER (0..1000) | RO | mandatory | |||||||||
scalar · INTEGER (0..1000) · read-only · mandatory Indicates the maximum speed that this system can operate at. Due to backwards compatibility issue, 0 value should be treated as 0 Mbps. | |||||||||||||
| ShzOduSystemMode | 1.3.6.1.4.1.7262.2.2.1.2.3 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory Indicates the specific type of system this is.
| |||||||||||||
| ShzOduUpgradeLicensedSpeed | 1.3.6.1.4.1.7262.2.2.1.2.4 | DisplayString | WO | mandatory | |||||||||
scalar · DisplayString · write-only · mandatory Enter your apngFLEX key here along with the maximum speed for that key to upgrade the FLEX system. Format: [speed] [key] Example: 50 abc123 | |||||||||||||
| NhzOduInventory | 1.3.6.1.4.1.7262.2.2.1.3 | ||||||||||||
| NhzOduHwInventory | 1.3.6.1.4.1.7262.2.2.1.3.1 | ||||||||||||
| ShzOduUnitSerialNo | 1.3.6.1.4.1.7262.2.2.1.3.1.1 | DisplayString | RO | mandatory | DW0123456789 | ||||||||
scalar · DisplayString · read-only · mandatory A textual string containing Serial no of the Unit. Example values from LibreNMS test devices
| |||||||||||||
| ShzOduUnitAssemblylNo | 1.3.6.1.4.1.7262.2.2.1.3.1.2 | DisplayString | RO | mandatory | CLHP28B1CR1 | ||||||||
scalar · DisplayString · read-only · mandatory A textual string containing assembly no of the Unit. Example values from LibreNMS test devices
| |||||||||||||
| ShzOduIfSerialNo | 1.3.6.1.4.1.7262.2.2.1.3.1.3 | DisplayString | RO | mandatory | |||||||||
scalar · DisplayString · read-only · mandatory A textual string containing Serial no of the IF. | |||||||||||||
| ShzOduIfAssemblylNo | 1.3.6.1.4.1.7262.2.2.1.3.1.4 | DisplayString | RO | mandatory | |||||||||
scalar · DisplayString · read-only · mandatory A textual string containing assembly no of the IF. | |||||||||||||
| ShzOduRfSerialNo | 1.3.6.1.4.1.7262.2.2.1.3.1.5 | DisplayString | RO | mandatory | |||||||||
scalar · DisplayString · read-only · mandatory A textual string containing Serial no of the RF. | |||||||||||||
| ShzOduRfAssemblylNo | 1.3.6.1.4.1.7262.2.2.1.3.1.6 | DisplayString | RO | mandatory | |||||||||
scalar · DisplayString · read-only · mandatory A textual string containing assembly no of the RF. | |||||||||||||
| ShzOduNccSerialNo | 1.3.6.1.4.1.7262.2.2.1.3.1.7 | DisplayString | RO | mandatory | |||||||||
scalar · DisplayString · read-only · mandatory A textual string containing Serial no of the NCC. | |||||||||||||
| ShzOduNccAssemblylNo | 1.3.6.1.4.1.7262.2.2.1.3.1.8 | DisplayString | RO | mandatory | |||||||||
scalar · DisplayString · read-only · mandatory A textual string containing assembly no of the NCC. | |||||||||||||
| ShzOduDiplexerSerialNo | 1.3.6.1.4.1.7262.2.2.1.3.1.9 | DisplayString | RO | mandatory | |||||||||
scalar · DisplayString · read-only · mandatory A textual string containing Serial no of the Diplexer. | |||||||||||||
| ShzOduDiplexerAssemblylNo | 1.3.6.1.4.1.7262.2.2.1.3.1.10 | DisplayString | RO | mandatory | |||||||||
scalar · DisplayString · read-only · mandatory A textual string containing assembly no of the Diplexer. | |||||||||||||
| NhzOduSwInventory | 1.3.6.1.4.1.7262.2.2.1.3.2 | ||||||||||||
| ShzOduSystemOmniVersionNo | 1.3.6.1.4.1.7262.2.2.1.3.2.1 | DisplayString | RO | mandatory | 1.04.08 | ||||||||
scalar · DisplayString · read-only · mandatory The version number of the Omni. Example values from LibreNMS test devices
| |||||||||||||
| ShzOduModemOmniVersionNo | 1.3.6.1.4.1.7262.2.2.1.3.2.2 | DisplayString | RO | mandatory | |||||||||
scalar · DisplayString · read-only · mandatory The version number of the Modem FPGA. | |||||||||||||
| ShzOduFrequencyFileVersionNo | 1.3.6.1.4.1.7262.2.2.1.3.2.3 | DisplayString | RO | mandatory | |||||||||
scalar · DisplayString · read-only · mandatory The version number of the FrequencyFile. | |||||||||||||
| ShzOduMibVersionNo | 1.3.6.1.4.1.7262.2.2.1.3.2.4 | DisplayString | RO | mandatory | |||||||||
scalar · DisplayString · read-only · mandatory The version number of the MIB. | |||||||||||||
| NhzOduAtpc | 1.3.6.1.4.1.7262.2.2.1.4 | ||||||||||||
| ShzOduAtpcEnable | 1.3.6.1.4.1.7262.2.2.1.4.1 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory Indicates whether Automatic Transmit Power Control (ATPC) is enabled.
| |||||||||||||
| ShzOduAtpcCoordinatedPowerDbm | 1.3.6.1.4.1.7262.2.2.1.4.2 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory This defines the coordinated power level.
The value is multiplied by 10. e.g. A display
of 133 is actually 13.3 dBm. | |||||||||||||
| NhzOduAam | 1.3.6.1.4.1.7262.2.2.1.5 | ||||||||||||
| ShzOduAamEnable | 1.3.6.1.4.1.7262.2.2.1.5.1 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory Indicates whether Automatic Adaptive Modulation(AAM) is enabled.
| |||||||||||||
| NhzOduPeerSysInfo | 1.3.6.1.4.1.7262.2.2.1.6 | ||||||||||||
| ShzOduPeerMacAddress | 1.3.6.1.4.1.7262.2.2.1.6.1 | DisplayString | RO | mandatory | |||||||||
scalar · DisplayString · read-only · mandatory The MAC Address of the peer network interface card. | |||||||||||||
| ShzOduPeerIpAddress | 1.3.6.1.4.1.7262.2.2.1.6.2 | IpAddress | RO | mandatory | |||||||||
scalar · IpAddress · read-only · mandatory The IP Address of the peer network interface card. | |||||||||||||
| ShzOduPeerSubnetMask | 1.3.6.1.4.1.7262.2.2.1.6.3 | IpAddress | RO | mandatory | |||||||||
scalar · IpAddress · read-only · mandatory The subnet mask for the peer network interface card. | |||||||||||||
| NhzOduSysRedundancy | 1.3.6.1.4.1.7262.2.2.1.7 | ||||||||||||
| ShzOduSystemRedundancyMode | 1.3.6.1.4.1.7262.2.2.1.7.1 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory allows the user to set system redundancy mode: [ off | primary-hsb-1wire | secondary-hsb-1wire | primary-hsb-2wire | secondary-hsb-2wire ]
| |||||||||||||
| ShzOduSystemRedundancyOverride | 1.3.6.1.4.1.7262.2.2.1.7.2 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory Allows the user to override the active link. User can forces the link to stay on either primary or secondary link.
| |||||||||||||
| ShzOduSystemRedundancyLinkStatus | 1.3.6.1.4.1.7262.2.2.1.7.3 | DisplayString | RO | mandatory | |||||||||
scalar · DisplayString · read-only · mandatory Indicates the redundancy link status. | |||||||||||||
| ShzOduSystemRedundancyStandbyEnetState | 1.3.6.1.4.1.7262.2.2.1.7.4 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory Allows the user to set standby enet(port1) state.
| |||||||||||||
| ShzOduSystemRedundancyStateSwitch | 1.3.6.1.4.1.7262.2.2.1.7.5 | INTEGER | WO | mandatory | |||||||||
scalar · INTEGER · write-only · mandatory Allows the user to switch redundancy state.
| |||||||||||||
| NhzOduAuthentication | 1.3.6.1.4.1.7262.2.2.2 | ||||||||||||
| ShzOduUniquePeerAuthenticationKey | 1.3.6.1.4.1.7262.2.2.2.1 | DisplayString (SIZE (0..34)) | RW | mandatory | |||||||||
scalar · DisplayString (SIZE (0..34)) · read-write · mandatory The serial number of the peer node that this node will communicate with. This is only used when authentication mode is set to unique. | |||||||||||||
| ShzOduPeerDetectedSerialNumber | 1.3.6.1.4.1.7262.2.2.2.2 | DisplayString | RO | mandatory | |||||||||
scalar · DisplayString · read-only · mandatory The serial number of the peer node that the system is presently communicating with. This is only used when authentication is set to unique. | |||||||||||||
| ShzOduAuthenticationMode | 1.3.6.1.4.1.7262.2.2.2.3 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory This sets the authentication mode for the system.If configured for unique authentication, an horizon node only exchanges user traffic with one other horizon node. The serial number is used in this case. If configured for group authentication, an horizon node exchanges user traffic with another horizon node of the same group and uses the authentication keys.
| |||||||||||||
| ShzOduAuthenticationFailureAction | 1.3.6.1.4.1.7262.2.2.2.4 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory This sets the authentication failure action for the system. Block traffic will block all user traffic including remote management access. Pass traffic will allow all user traffic to be sent and recieved
| |||||||||||||
| ShzOduPeerAuthenticationStatus | 1.3.6.1.4.1.7262.2.2.2.5 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory Specifies the current authentication status of the system. Authenticated means authentication is on and the system has been authenticated, notAuthenticated means authentication is off or the system has not communicated yet with the other node, explicit authentication failure means authentication is on and authentication has failed
| |||||||||||||
| NhzOduNetworkManagement | 1.3.6.1.4.1.7262.2.2.3 | ||||||||||||
| ShzOduMacAddress | 1.3.6.1.4.1.7262.2.2.3.1 | DisplayString | RO | mandatory | |||||||||
scalar · DisplayString · read-only · mandatory The MAC Address of the network interface card. | |||||||||||||
| ShzOduNetworkManagementInterface | 1.3.6.1.4.1.7262.2.2.3.2 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory Describes the network management interface connection options.
| |||||||||||||
| ShzOduIpAddress | 1.3.6.1.4.1.7262.2.2.3.3 | IpAddress | RO | mandatory | |||||||||
scalar · IpAddress · read-only · mandatory The IP Address of the network interface card. | |||||||||||||
| ShzOduSubnetMask | 1.3.6.1.4.1.7262.2.2.3.4 | IpAddress | RO | mandatory | |||||||||
scalar · IpAddress · read-only · mandatory The subnet mask for the network interface card. | |||||||||||||
| ShzOduDefaultGateway | 1.3.6.1.4.1.7262.2.2.3.5 | IpAddress | RO | mandatory | |||||||||
scalar · IpAddress · read-only · mandatory The default gateway for the network interface card | |||||||||||||
| ShzOduTelnetAccessMode | 1.3.6.1.4.1.7262.2.2.3.6 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory Indicates whether Telnet access is allowed.
| |||||||||||||
| ShzOduSshAccessMode | 1.3.6.1.4.1.7262.2.2.3.7 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory Indicates whether ssh access is allowed.
| |||||||||||||
| ShzOduVlanTagEnable | 1.3.6.1.4.1.7262.2.2.3.8 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory Indicates whether VLAN tagging is enabled.
| |||||||||||||
| ShzOduVlanTagId | 1.3.6.1.4.1.7262.2.2.3.9 | INTEGER | RW | mandatory | |||||||||
| ShzOduVlanTagPriority | 1.3.6.1.4.1.7262.2.2.3.10 | INTEGER | RW | mandatory | |||||||||
| NhzOduNetworkInterface | 1.3.6.1.4.1.7262.2.2.4 | ||||||||||||
| NhzOduEnetPort1 | 1.3.6.1.4.1.7262.2.2.4.1 | ||||||||||||
| ShzOduEnetPort1Description | 1.3.6.1.4.1.7262.2.2.4.1.1 | DisplayString | RO | mandatory | |||||||||
scalar · DisplayString · read-only · mandatory Describes the functionality of the port1 | |||||||||||||
| NhzOduEnetPort1Config | 1.3.6.1.4.1.7262.2.2.4.1.2 | ||||||||||||
| ShzOduEnetPort1AutoNegotiation | 1.3.6.1.4.1.7262.2.2.4.1.2.1 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory port1 Turns auto-negotiation on or off. Turning off results in the interface defaulting to 100BaseT, Full Duplex.
| |||||||||||||
| ShzOduEnetPort1Speed | 1.3.6.1.4.1.7262.2.2.4.1.2.2 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory Configure the port1 interface speed .
| |||||||||||||
| ShzOduEnetPort1Duplex | 1.3.6.1.4.1.7262.2.2.4.1.2.3 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory Configure the port1 interface duplex.
| |||||||||||||
| ShzOduEnetPort1Media | 1.3.6.1.4.1.7262.2.2.4.1.2.4 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory Configure the port1 interface media.
| |||||||||||||
| ShzOduEnetPort1AdminState | 1.3.6.1.4.1.7262.2.2.4.1.2.5 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory Configure the port1 interface media.
| |||||||||||||
| ShzOduEnetPort1OpticalTransceiverState | 1.3.6.1.4.1.7262.2.2.4.1.2.6 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory When it is on, optical transmitter for port1 is enabled. Otherwise optical transmitter is disabled.
| |||||||||||||
| ShzOduEnetPort1PauseFrameEnable | 1.3.6.1.4.1.7262.2.2.4.1.2.7 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory When PAUSE is enabled, port1 pause frames can be generated by the system and the pause frames will flow toward the link partner on the network. When PAUSE is not enabled, no pause frames will be generated by the system.
| |||||||||||||
| ShzOduEnetPort1MaxFrameSize | 1.3.6.1.4.1.7262.2.2.4.1.2.8 | INTEGER (1600..9600) | RW | mandatory | |||||||||
scalar · INTEGER (1600..9600) · read-write · mandatory For port1 the default maximum frame size is 1600 bytes. The settable maximum frame size must be a multiple of 128. If the chosen maximum frame size is not a multiple of 128, its closest number which is a multiple of 128 is actually used. The settable lowest maximum frame size is 1664, and the settable highest maximum frame size is 9600. If the chosen maximum frame size is out of this range, the default maximum frame size of 1600 is used. | |||||||||||||
| ShzOduEnetPort1DroppedEnetFramesThresholdParameters | 1.3.6.1.4.1.7262.2.2.4.1.2.9 | DisplayString (SIZE (0..24)) | RW | mandatory | |||||||||
scalar · DisplayString (SIZE (0..24)) · read-write · mandatory A read-write string: The threshold, in percent, and the number of seconds that it must exceed this threshold are programmed by the user. An example of the format of the string is as follows: '70 10'. The first parameter is the percentage of frames that are dropped, the second is the time in seconds that the threshold must be exceeded. The single quote marks i.e. ' ' are not used in the command. | |||||||||||||
| ShzOduEnetPort1BandwidthUtilizationThresholdParameters | 1.3.6.1.4.1.7262.2.2.4.1.2.10 | DisplayString (SIZE (0..24)) | RW | mandatory | |||||||||
scalar · DisplayString (SIZE (0..24)) · read-write · mandatory A read-write string: The percentage of available bandwidth threshold and the number of seconds that it must exceed this threshold are programmed by the user. An example of the format of the string is as follows: '70 10'. The first parameter is the threshold point in percent, the number of seconds that the threshold must be exceeded. The single quote marks i.e. ' ' are not used in the command. | |||||||||||||
| NhzOduEnetPort1Status | 1.3.6.1.4.1.7262.2.2.4.1.3 | ||||||||||||
| ShzOduEnetPort1LinkStatus | 1.3.6.1.4.1.7262.2.2.4.1.3.1 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory Indicates the port1 link status.
| |||||||||||||
| ShzOduEnetPort1AutoNegotiationStatus | 1.3.6.1.4.1.7262.2.2.4.1.3.2 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory Indicates the port1 AutoNegotiation status.
| |||||||||||||
| ShzOduEnetPort1SpeedStatus | 1.3.6.1.4.1.7262.2.2.4.1.3.3 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory Indicates the port1 interface speed status.
| |||||||||||||
| ShzOduEnetPort1DuplexStatus | 1.3.6.1.4.1.7262.2.2.4.1.3.4 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory Indicates the port1 interface duplex status.
| |||||||||||||
| ShzOduEnetPort1MediaStatus | 1.3.6.1.4.1.7262.2.2.4.1.3.5 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory Indicates the port1 interface media status.
| |||||||||||||
| NhzOduEnetPort1Stats | 1.3.6.1.4.1.7262.2.2.4.1.4 | ||||||||||||
| ShzOduEnetPort1TxFrames | 1.3.6.1.4.1.7262.2.2.4.1.4.1 | Counter | RO | mandatory | |||||||||
scalar · Counter · read-only · mandatory The current count of port1 frames sent. | |||||||||||||
| ShzOduEnetPort1TxBytes | 1.3.6.1.4.1.7262.2.2.4.1.4.2 | Counter | RO | mandatory | |||||||||
scalar · Counter · read-only · mandatory The current count of port1 bytes sent. | |||||||||||||
| ShzOduEnetPort1RxFrames | 1.3.6.1.4.1.7262.2.2.4.1.4.3 | Counter | RO | mandatory | |||||||||
scalar · Counter · read-only · mandatory The current count of port1 frames received. | |||||||||||||
| ShzOduEnetPort1RxBytes | 1.3.6.1.4.1.7262.2.2.4.1.4.4 | Counter | RO | mandatory | |||||||||
scalar · Counter · read-only · mandatory The current count of port1 bytes received. | |||||||||||||
| ShzOduEnetPort1RxFramesInError | 1.3.6.1.4.1.7262.2.2.4.1.4.5 | Counter | RO | mandatory | 0 | ||||||||
scalar · Counter · read-only · mandatory The current count of port1 frames received in error. Example values from LibreNMS test devices
| |||||||||||||
| ShzOduEnetPort1RxFramesCRCError | 1.3.6.1.4.1.7262.2.2.4.1.4.6 | Counter | RO | mandatory | 0 | ||||||||
scalar · Counter · read-only · mandatory The current count of CRC error frames received for port1. Example values from LibreNMS test devices
| |||||||||||||
| ShzOduEnetPort1BWUtilization | 1.3.6.1.4.1.7262.2.2.4.1.4.7 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory The carried load over link capacity for port1. | |||||||||||||
| ShzOduEnetPort1IngressDataRate | 1.3.6.1.4.1.7262.2.2.4.1.4.8 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory The data rate coming into the ethernet for port1.
The data rate you see is multiplied by 100. e.g. A display
of 1530 is actually 15.30 Mpbs | |||||||||||||
| ShzOduEnetPort1EgressDataRate | 1.3.6.1.4.1.7262.2.2.4.1.4.9 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory The data rate going out of the ethernet for port1.
The data rate you see is multiplied by 100. e.g. A display
of 1530 is actually 15.30 Mpbs. | |||||||||||||
| ShzOduEnetPort1FramesInQueue1 | 1.3.6.1.4.1.7262.2.2.4.1.4.10 | Counter | RO | mandatory | |||||||||
scalar · Counter · read-only · mandatory The current count of port1 frames passed through queue 1. | |||||||||||||
| ShzOduEnetPort1FramesInQueue2 | 1.3.6.1.4.1.7262.2.2.4.1.4.11 | Counter | RO | mandatory | |||||||||
scalar · Counter · read-only · mandatory The current count of port1 frames passed through queue 2. | |||||||||||||
| ShzOduEnetPort1FramesInQueue3 | 1.3.6.1.4.1.7262.2.2.4.1.4.12 | Counter | RO | mandatory | |||||||||
scalar · Counter · read-only · mandatory The current count of NIC frames passed through queue 3. | |||||||||||||
| ShzOduEnetPort1FramesInQueue4 | 1.3.6.1.4.1.7262.2.2.4.1.4.13 | Counter | RO | mandatory | |||||||||
scalar · Counter · read-only · mandatory The current count of NIC frames passed through queue 4. | |||||||||||||
| ShzOduEnetPort1FramesInQueue1Discarded | 1.3.6.1.4.1.7262.2.2.4.1.4.14 | Counter | RO | mandatory | |||||||||
scalar · Counter · read-only · mandatory The current count of NIC frames received in queue 2 that were discarded, but due to an error. One possible reason is lack of buffer space. | |||||||||||||
| ShzOduEnetPort1FramesInQueue2Discarded | 1.3.6.1.4.1.7262.2.2.4.1.4.15 | Counter | RO | mandatory | |||||||||
scalar · Counter · read-only · mandatory The current count of port1 frames received in queue 2 that were discarded, but due to an error. One possible reason is lack of buffer space. | |||||||||||||
| ShzOduEnetPort1FramesInQueue3Discarded | 1.3.6.1.4.1.7262.2.2.4.1.4.16 | Counter | RO | mandatory | |||||||||
scalar · Counter · read-only · mandatory The current count of port1 frames received in queue 3 that were discarded, but due to an error. One possible reason is lack of buffer space. | |||||||||||||
| ShzOduEnetPort1FramesInQueue4Discarded | 1.3.6.1.4.1.7262.2.2.4.1.4.17 | Counter | RO | mandatory | |||||||||
scalar · Counter · read-only · mandatory The current count of port1 frames received in queue 4 that were discarded, but due to an error. One possible reason is lack of buffer space. | |||||||||||||
| NhzOduEnetPort2 | 1.3.6.1.4.1.7262.2.2.4.2 | ||||||||||||
| ShzOduEnetPort2Description | 1.3.6.1.4.1.7262.2.2.4.2.1 | DisplayString | RO | mandatory | |||||||||
scalar · DisplayString · read-only · mandatory Describes the functionality of the port2 | |||||||||||||
| NhzOduEnetPort2Config | 1.3.6.1.4.1.7262.2.2.4.2.2 | ||||||||||||
| ShzOduEnetPort2AutoNegotiation | 1.3.6.1.4.1.7262.2.2.4.2.2.1 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory port1 Turns auto-negotiation on or off. Turning off results in the interface defaulting to 100BaseT, Full Duplex.
| |||||||||||||
| ShzOduEnetPort2Speed | 1.3.6.1.4.1.7262.2.2.4.2.2.2 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory Configure the port1 interface speed .
| |||||||||||||
| ShzOduEnetPort2Duplex | 1.3.6.1.4.1.7262.2.2.4.2.2.3 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory Configure the port1 interface duplex.
| |||||||||||||
| ShzOduEnetPort2AdminState | 1.3.6.1.4.1.7262.2.2.4.2.2.4 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory Configure the port2 shutdown media.
| |||||||||||||
| NhzOduEnetPort2Status | 1.3.6.1.4.1.7262.2.2.4.2.3 | ||||||||||||
| ShzOduEnetPort2LinkStatus | 1.3.6.1.4.1.7262.2.2.4.2.3.1 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory Indicates the Port2 link status.
| |||||||||||||
| ShzOduEnetPort2AutoNegotiationStatus | 1.3.6.1.4.1.7262.2.2.4.2.3.2 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory Indicates the Port2 AutoNegotiation status.
| |||||||||||||
| ShzOduEnetPort2SpeedStatus | 1.3.6.1.4.1.7262.2.2.4.2.3.3 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory Indicates the Port2 interface speed status.
| |||||||||||||
| ShzOduEnetPort2DuplexStatus | 1.3.6.1.4.1.7262.2.2.4.2.3.4 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory Indicates the Port2 interface duplex status.
| |||||||||||||
| ShzOduEnetPort2MediaStatus | 1.3.6.1.4.1.7262.2.2.4.2.3.5 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory Indicates the port1 interface media status.
| |||||||||||||
| NhzOduEnetPort2Stats | 1.3.6.1.4.1.7262.2.2.4.2.4 | ||||||||||||
| ShzOduEnetPort2TxFrames | 1.3.6.1.4.1.7262.2.2.4.2.4.1 | Counter | RO | mandatory | |||||||||
scalar · Counter · read-only · mandatory The current count of Port2 frames sent. | |||||||||||||
| ShzOduEnetPort2TxBytes | 1.3.6.1.4.1.7262.2.2.4.2.4.2 | Counter | RO | mandatory | |||||||||
scalar · Counter · read-only · mandatory The current count of Port2 bytes sent. | |||||||||||||
| ShzOduEnetPort2RxFrames | 1.3.6.1.4.1.7262.2.2.4.2.4.3 | Counter | RO | mandatory | |||||||||
scalar · Counter · read-only · mandatory The current count of Port2 frames received. | |||||||||||||
| ShzOduEnetPort2RxBytes | 1.3.6.1.4.1.7262.2.2.4.2.4.4 | Counter | RO | mandatory | |||||||||
scalar · Counter · read-only · mandatory The current count of Port2 bytes received. | |||||||||||||
| ShzOduEnetPort2RxFramesInError | 1.3.6.1.4.1.7262.2.2.4.2.4.5 | Counter | RO | mandatory | 0 | ||||||||
scalar · Counter · read-only · mandatory The current count of Port2 frames received in error. Example values from LibreNMS test devices
| |||||||||||||
| ShzOduEnetPort2RxFramesCrcError | 1.3.6.1.4.1.7262.2.2.4.2.4.6 | Counter | RO | mandatory | 0 | ||||||||
scalar · Counter · read-only · mandatory The current count of CRC error frames received for Port2. Example values from LibreNMS test devices
| |||||||||||||
| NhzOduWirelessInterface | 1.3.6.1.4.1.7262.2.2.5 | ||||||||||||
| NhzOduWirelessPort1 | 1.3.6.1.4.1.7262.2.2.5.1 | ||||||||||||
| ShzOduWirelessPort1Description | 1.3.6.1.4.1.7262.2.2.5.1.1 | DisplayString | RO | mandatory | |||||||||
scalar · DisplayString · read-only · mandatory Describes the functionality of the Wireless Interface1 | |||||||||||||
| NhzOduModem1 | 1.3.6.1.4.1.7262.2.2.5.1.2 | ||||||||||||
| ShzOduModem1AdminStatus | 1.3.6.1.4.1.7262.2.2.5.1.2.1 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory The current admin state of the interface. Testing indicates that no operational packets can be passed.
| |||||||||||||
| ShzOduModem1OperStatus | 1.3.6.1.4.1.7262.2.2.5.1.2.2 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory The current operational state of the interface. Testing indicates that no operational packets can be passed.
| |||||||||||||
| ShzOduModem1Reset | 1.3.6.1.4.1.7262.2.2.5.1.2.3 | INTEGER (0..1) | WO | mandatory | |||||||||
scalar · INTEGER (0..1) · write-only · mandatory Writing 1 to this object causes the modem card to be reset. All other values are not recognized. This variable always reads back as 0. mdmOperStatus should be polled by the user after this object is written to, to verify that the modem card has been reset. Not applicable in this release | |||||||||||||
| ShzOduModem1ChannelizedRSL | 1.3.6.1.4.1.7262.2.2.5.1.2.4 | INTEGER | RO | mandatory | -445 | ||||||||
scalar · INTEGER · read-only · mandatory An estimate of the modem's channelized RSL. Divide the value by 10 to get the actual RSL value Example values from LibreNMS test devices
| |||||||||||||
| ShzOduModem1ModulationType | 1.3.6.1.4.1.7262.2.2.5.1.2.5 | INTEGER | RO | mandatory | qam256(7) | ||||||||
scalar · INTEGER · read-only · mandatory The modulation type of the modem, distinguished according to the physical/link protocol.
Example values from LibreNMS test devices
| |||||||||||||
| ShzOduModem1CurrentRxSpeed | 1.3.6.1.4.1.7262.2.2.5.1.2.6 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory An estimate of the modem's current Rx bandwidth in bits per second. Divide the value by 10000 to get the actual data rate in Mbps | |||||||||||||
| ShzOduModem1CurrentTxSpeed | 1.3.6.1.4.1.7262.2.2.5.1.2.7 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory An estimate of the modem's current Tx bandwidth in bits per second. Divide the value by 10000 to get the actual data rate in Mbps | |||||||||||||
| ShzOduModem1SNR | 1.3.6.1.4.1.7262.2.2.5.1.2.8 | INTEGER | RO | mandatory | 373 | ||||||||
scalar · INTEGER · read-only · mandatory SNR value in dB. Divide the value by 10 to get the actual SNR. Example values from LibreNMS test devices
| |||||||||||||
| ShzOduModem1EbToNoiseRatio | 1.3.6.1.4.1.7262.2.2.5.1.2.9 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory The ratio of the modem Estimated Energy per information bit to Noise power spectral density. Divide the value by 10 to get the actual EbToNoiseRatio | |||||||||||||
| ShzOduModem1EqualizerStress | 1.3.6.1.4.1.7262.2.2.5.1.2.10 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory Indicates the average magnitude of all the equalizer taps to provide a measure of how hard the equalizer is working. | |||||||||||||
| ShzOduModem1SNRThresholdParameters | 1.3.6.1.4.1.7262.2.2.5.1.2.11 | DisplayString (SIZE (0..24)) | RW | mandatory | |||||||||
scalar · DisplayString (SIZE (0..24)) · read-write · mandatory A read-write string | |||||||||||||
| ShzOduModem1ChannelizedRslBelowThresholdParameters | 1.3.6.1.4.1.7262.2.2.5.1.2.12 | DisplayString (SIZE (0..24)) | RW | mandatory | |||||||||
scalar · DisplayString (SIZE (0..24)) · read-write · mandatory A read-write string: The threshold in dBm and the number of seconds threshold are programmed by the user. An example of the format of the string is as follows: '-75 10'. The first parameter power level in dBm, the second is the time in seconds that the threshold must be exceeded. In this example the threshold -75 dBm and the time is set to 10 seconds. The single quote marks i.e. ' ' are not used in the command. | |||||||||||||
| ShzOduModem1LastChange | 1.3.6.1.4.1.7262.2.2.5.1.2.13 | TimeTicks | RO | mandatory | |||||||||
scalar · TimeTicks · read-only · mandatory The value of sysUpTime at the time the modem entered its current operational state. If the current state was entered prior to the last re-initialization of the local network management subsystem, then this object contains a zero value. | |||||||||||||
| ShzOduModem1ChannelizedRSLUnsignedInt | 1.3.6.1.4.1.7262.2.2.5.1.2.14 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory An estimate of the modem's channelized RSL in dBm. The number is divided by 10. e.g. -432 is actually -43.2dBm. Object provided mainly to accomodate plotting of negative RSL values which is not supported in some EMS (Ex: CastleRock). Please use 'hzOduModem1ChannelizedRSL' object if your EMS supports plotting of -ve integer. | |||||||||||||
| NhzOduModem1Statistics | 1.3.6.1.4.1.7262.2.2.5.1.2.15 | ||||||||||||
| ShzOduModem1TxFrames | 1.3.6.1.4.1.7262.2.2.5.1.2.15.1 | Counter | RO | mandatory | |||||||||
scalar · Counter · read-only · mandatory The current count of Modem frames sent. | |||||||||||||
| ShzOduModem1RxFramesOK | 1.3.6.1.4.1.7262.2.2.5.1.2.15.2 | Counter | RO | mandatory | |||||||||
scalar · Counter · read-only · mandatory The current count of Modem frames received. | |||||||||||||
| ShzOduModem1RxFramesError | 1.3.6.1.4.1.7262.2.2.5.1.2.15.3 | Counter | RO | mandatory | 340280 | ||||||||
scalar · Counter · read-only · mandatory The current count of Modem frames received in error. Example values from LibreNMS test devices
| |||||||||||||
| ShzOduModem1RxFramesQueueDiscarded | 1.3.6.1.4.1.7262.2.2.5.1.2.15.4 | Counter | RO | mandatory | |||||||||
scalar · Counter · read-only · mandatory The current count of Modem frames in the queue that were discarded. | |||||||||||||
| ShzOduModem1TxBlocks | 1.3.6.1.4.1.7262.2.2.5.1.2.15.5 | Counter | RO | mandatory | |||||||||
scalar · Counter · read-only · mandatory The current count of Modem blocks transmitted. | |||||||||||||
| ShzOduModem1RxBlocksOK | 1.3.6.1.4.1.7262.2.2.5.1.2.15.6 | Counter | RO | mandatory | |||||||||
scalar · Counter · read-only · mandatory The current count of Modem blocks received. | |||||||||||||
| ShzOduModem1RxBlocksError | 1.3.6.1.4.1.7262.2.2.5.1.2.15.7 | Counter | RO | mandatory | 23738900 | ||||||||
scalar · Counter · read-only · mandatory The current count of Modem blocks received in error. Example values from LibreNMS test devices
| |||||||||||||
| NhzOduRadio1 | 1.3.6.1.4.1.7262.2.2.5.1.3 | ||||||||||||
| ShzOduRadio1OperStatus | 1.3.6.1.4.1.7262.2.2.5.1.3.1 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory The current operational state of the interface. Testing indicates that no operational packets can be passed. Testing also indicates that a firmware upgrade may be in progress
| |||||||||||||
| ShzOduRadio1TransmitPowerDbm | 1.3.6.1.4.1.7262.2.2.5.1.3.2 | INTEGER | RW | mandatory | 194 | ||||||||
scalar · INTEGER · read-write · mandatory This defines the transmit level of the radio. If ATPC is enabled, you can't change the transmit power. The power you see is divided by 10. e.g. A display of 133 is actually 13.3 dBm. If the radio is operational and not muted, it is the current transmitting power. If the radio is operational and muted, it is the programmed transmitting power, and will transmit at this level when the radio is un-muted. If the radio is not operational it is the programmed transmitting power, and will transmit at this level when the radio is operational and not muted. If the radio does not have transmit calibration tables programmed into its EEPROM, this transmit power level cannot be used as it is not possible to accurately calculate the actual transmit level. In this case this object will return -99. Example values from LibreNMS test devices
| |||||||||||||
| ShzOduRadio1ProgrammedAntennaDiameter | 1.3.6.1.4.1.7262.2.2.5.1.3.3 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory This defines the diameter of the antenna used by the system represented in inches.
| |||||||||||||
| ShzOduRadio1PowerOption | 1.3.6.1.4.1.7262.2.2.5.1.3.4 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory This indicates the power option of the radio: normal or high power.
| |||||||||||||
| ShzOduRadio1TxState | 1.3.6.1.4.1.7262.2.2.5.1.3.5 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory This indicates the power option of the radio: normal or high power.
| |||||||||||||
| ShzOduRadio1Temperature | 1.3.6.1.4.1.7262.2.2.5.1.3.6 | INTEGER | RO | mandatory | 382 | ||||||||
scalar · INTEGER · read-only · mandatory The Radio temperature in degree Centigrade. The actual temperature is got by dividing the number by 10. e.g. -432 is actually -43.2 degree centigrade. Example values from LibreNMS test devices
| |||||||||||||
| NhzOduFrequencies | 1.3.6.1.4.1.7262.2.2.6 | ||||||||||||
| ShzOduRadioBand | 1.3.6.1.4.1.7262.2.2.6.1 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory The radio frequency standard used in the system. Frequency bands are divided into sub bands. ie FCC 23 Ghz Band is comprised of fcc23a, fcc23b, fcc23c and fcc23d which make up the entire FCC23 band
| |||||||||||||
| ShzOduFreqGroupSelected | 1.3.6.1.4.1.7262.2.2.6.2 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory The frequency group selected for the system. The frequency subbands are divided into frequency groups txHigh and txLow. An horizon system must have one node configured to txLow and the other node configure to txHigh
| |||||||||||||
| ThzOduTxHighFreqTable | 1.3.6.1.4.1.7262.2.2.6.3 | NA | mandatory | ||||||||||
table · not-accessible · mandatory A table of txHigh frequency settings for the system | |||||||||||||
| RhzOduTxHighFreqEntry | 1.3.6.1.4.1.7262.2.2.6.3.1 | NA | mandatory | ||||||||||
row · not-accessible · mandatory A txHighFrequency entry containing all the frequency values
| |||||||||||||
| ChzOduTxHighFreqIndex | 1.3.6.1.4.1.7262.2.2.6.3.1.1 | INTEGER | RO | mandatory | |||||||||
column · INTEGER · read-only · mandatory A unique value for each frequency channel. | |||||||||||||
| ChzOduTxHighFreqChannelIndex | 1.3.6.1.4.1.7262.2.2.6.3.1.2 | DisplayString | RO | mandatory | |||||||||
column · DisplayString · read-only · mandatory The channel index for the frequency. | |||||||||||||
| ChzOduTxHighFreqTransmitRfFrequency | 1.3.6.1.4.1.7262.2.2.6.3.1.3 | INTEGER | RO | mandatory | |||||||||
column · INTEGER · read-only · mandatory The RF TX frequency in MHz. | |||||||||||||
| ChzOduTxHighFreqReceiveRfFrequency | 1.3.6.1.4.1.7262.2.2.6.3.1.4 | INTEGER | RO | mandatory | |||||||||
column · INTEGER · read-only · mandatory The RF RX frequency in MHz. | |||||||||||||
| ChzOduTxHighFreqProgrammed | 1.3.6.1.4.1.7262.2.2.6.3.1.5 | INTEGER | RW | mandatory | |||||||||
column · INTEGER · read-write · mandatory Specifies the operating frequency channel for the modem. ***Only 1 index may be selected in a 1 modem system.
| |||||||||||||
| ThzOduTxLowFreqTable | 1.3.6.1.4.1.7262.2.2.6.4 | NA | mandatory | ||||||||||
table · not-accessible · mandatory A table of txLow frequency settings for the system | |||||||||||||
| RhzOduTxLowFreqEntry | 1.3.6.1.4.1.7262.2.2.6.4.1 | NA | mandatory | ||||||||||
row · not-accessible · mandatory A hzOduTxLowFrequeny entry containing the frequency values for a specific index
| |||||||||||||
| ChzOduTxLowFreqIndex | 1.3.6.1.4.1.7262.2.2.6.4.1.1 | INTEGER | RO | mandatory | |||||||||
column · INTEGER · read-only · mandatory A unique value for each frequency channel. | |||||||||||||
| ChzOduTxLowFreqChannelIndex | 1.3.6.1.4.1.7262.2.2.6.4.1.2 | DisplayString | RO | mandatory | |||||||||
column · DisplayString · read-only · mandatory The channel index for the frequency. | |||||||||||||
| ChzOduTxLowFreqTransmitRfFrequency | 1.3.6.1.4.1.7262.2.2.6.4.1.3 | INTEGER | RO | mandatory | |||||||||
column · INTEGER · read-only · mandatory The RF TX frequency in MHz. | |||||||||||||
| ChzOduTxLowFreqReceiveRfFrequency | 1.3.6.1.4.1.7262.2.2.6.4.1.4 | INTEGER | RO | mandatory | |||||||||
column · INTEGER · read-only · mandatory The RF RX frequency in MHz. | |||||||||||||
| ChzOduTxLowFreqProgrammed | 1.3.6.1.4.1.7262.2.2.6.4.1.5 | INTEGER | RW | mandatory | |||||||||
column · INTEGER · read-write · mandatory Specifies the operating frequency channel for the modem. ***Only 1 index may be selected in a 1 modem system.
| |||||||||||||
| NhzOduProgrammedFrequency | 1.3.6.1.4.1.7262.2.2.6.5 | ||||||||||||
| ShzOduProgrammedFrequencyChannel | 1.3.6.1.4.1.7262.2.2.6.5.1 | DisplayString | RO | mandatory | |||||||||
scalar · DisplayString · read-only · mandatory The channel that has been programmed into the system. | |||||||||||||
| ShzOduProgrammedFrequencyTxRf | 1.3.6.1.4.1.7262.2.2.6.5.2 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory The programmed RF TX frequency in MHz. | |||||||||||||
| ShzOduProgrammedFrequencyRxRf | 1.3.6.1.4.1.7262.2.2.6.5.3 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory The RF RX frequency in MHz. | |||||||||||||
| NhzOduCalendar | 1.3.6.1.4.1.7262.2.2.7 | ||||||||||||
| ShzOduDate | 1.3.6.1.4.1.7262.2.2.7.1 | DisplayString | RO | mandatory | |||||||||
scalar · DisplayString · read-only · mandatory A string in the format as follows: XX/YY/ZZ Where XX = day of month (range 01 to 31) YY = month of year(range 01 to 12) ZZ = year (range 01 - 99) | |||||||||||||
| ShzOduTime | 1.3.6.1.4.1.7262.2.2.7.2 | DisplayString | RO | mandatory | |||||||||
scalar · DisplayString · read-only · mandatory A string in the format as follows:
aa:bb:cc:dd
Where aa = hour of day ( range 00 to 23 )
bb = minute of hour ( range 00 to 59 )
cc = second of minute( range 00 to 59 )
dd = hundredths of second (range 00 to 99) | |||||||||||||
| NhzOduAlarms | 1.3.6.1.4.1.7262.2.2.8 | ||||||||||||
| ShzOduClearAlarmCounters | 1.3.6.1.4.1.7262.2.2.8.1 | INTEGER | WO | mandatory | |||||||||
scalar · INTEGER · write-only · mandatory Clears the alarm counters for the specified group
| |||||||||||||
| NhzOduSystemAlarms | 1.3.6.1.4.1.7262.2.2.8.2 | ||||||||||||
| ShzOduExplicitAuthenticationFailure | 1.3.6.1.4.1.7262.2.2.8.2.1 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory Authentication of the peer horizon node has failed. The severity is critical, the probable cause is an incorrect authentication configuration on horizon faulty cable between the modem and radio, and recommended course of action is to check both ends of the link.
| |||||||||||||
| ShzOduExplicitAuthenticationFailureCount | 1.3.6.1.4.1.7262.2.2.8.2.2 | Counter | RO | mandatory | |||||||||
scalar · Counter · read-only · mandatory Indicates the number of times explicit authentication has failed. | |||||||||||||
| ShzOduAamConfigMismatch | 1.3.6.1.4.1.7262.2.2.8.2.3 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory In the near end Automatic Adaptive Modulation(AAM) feature set to on and in peer it is set to off
| |||||||||||||
| ShzOduAamConfigMismatchCount | 1.3.6.1.4.1.7262.2.2.8.2.4 | Counter | RO | mandatory | |||||||||
scalar · Counter · read-only · mandatory Indicates the approximate number of seconds AAMConfigMismatch alarm has been active. | |||||||||||||
| ShzOduAamActive | 1.3.6.1.4.1.7262.2.2.8.2.5 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory Indicates aam is active and system running on lowest modulation
| |||||||||||||
| ShzOduAamActiveCount | 1.3.6.1.4.1.7262.2.2.8.2.6 | Counter | RO | mandatory | |||||||||
scalar · Counter · read-only · mandatory Indicates the approximate number of seconds AAMActive alarm has been active. | |||||||||||||
| ShzOduAtpcConfigMismatch | 1.3.6.1.4.1.7262.2.2.8.2.7 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory In the near end Automatic Transmit Power Control(ATPC) feature set to on and in peer it is set to off
| |||||||||||||
| ShzOduAtpcConfigMismatchCount | 1.3.6.1.4.1.7262.2.2.8.2.8 | Counter | RO | mandatory | |||||||||
scalar · Counter · read-only · mandatory Indicates the approximate number of seconds AtpcConfigMismatch alarm has been active | |||||||||||||
| ShzOduSntpServerUnavailableAlarm | 1.3.6.1.4.1.7262.2.2.8.2.9 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory All of the SNTP servers are not available.
| |||||||||||||
| ShzOduSntpServerUnavailableAlarmCount | 1.3.6.1.4.1.7262.2.2.8.2.10 | Counter | RO | mandatory | |||||||||
scalar · Counter · read-only · mandatory Indicates how long in seconds all of the SNTP servers are not available. | |||||||||||||
| ShzOduFrequencyFileInvalid | 1.3.6.1.4.1.7262.2.2.8.2.11 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory Executing frequency file is valid or not
| |||||||||||||
| ShzOduFrequencyFileInvalidCount | 1.3.6.1.4.1.7262.2.2.8.2.12 | Counter | RO | mandatory | |||||||||
scalar · Counter · read-only · mandatory Indicates the time (in secs) since this alarm exist. | |||||||||||||
| ShzOduAtpcAutoDisabled | 1.3.6.1.4.1.7262.2.2.8.2.13 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory Indicates the ATPC set to off and system transmit at coordinated power.
| |||||||||||||
| ShzOduAtpcAutoDisabledCount | 1.3.6.1.4.1.7262.2.2.8.2.14 | Counter | RO | mandatory | |||||||||
scalar · Counter · read-only · mandatory Indicates the time (in secs) since this alarm exist. | |||||||||||||
| ShzOduPartnerRedundancyModeMismatch | 1.3.6.1.4.1.7262.2.2.8.2.15 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory Indicates partner redundancy mode mismatches.
| |||||||||||||
| ShzOduPartnerRedundancyModeMismatchCount | 1.3.6.1.4.1.7262.2.2.8.2.16 | Counter | RO | mandatory | |||||||||
scalar · Counter · read-only · mandatory Indicates the time (in secs) since this alarm exist. | |||||||||||||
| ShzOduPartnerConfigurationMismatch | 1.3.6.1.4.1.7262.2.2.8.2.17 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory Indicates partner configuration mismatches.
| |||||||||||||
| ShzOduPartnerConfigurationMismatchCount | 1.3.6.1.4.1.7262.2.2.8.2.18 | Counter | RO | mandatory | |||||||||
scalar · Counter · read-only · mandatory Indicates the time (in secs) since this alarm exist. | |||||||||||||
| ShzOduHsbActiveOnSecondary | 1.3.6.1.4.1.7262.2.2.8.2.19 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory Indicates the hsb active link is on secondary.
| |||||||||||||
| ShzOduHsbActiveOnSecondaryCount | 1.3.6.1.4.1.7262.2.2.8.2.20 | Counter | RO | mandatory | |||||||||
scalar · Counter · read-only · mandatory Indicates the time (in secs) since this alarm exist. | |||||||||||||
| ShzOduHsbOverrideByUser | 1.3.6.1.4.1.7262.2.2.8.2.21 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory Indicates the hsb mode is overrided by user.
| |||||||||||||
| ShzOduHsbOverrideByUserCount | 1.3.6.1.4.1.7262.2.2.8.2.22 | Counter | RO | mandatory | |||||||||
scalar · Counter · read-only · mandatory Indicates the time (in secs) since this alarm exist. | |||||||||||||
| ShzOduHsbCrossLinkActive | 1.3.6.1.4.1.7262.2.2.8.2.23 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory Indicates the hsb cross link is active.
| |||||||||||||
| ShzOduHsbCrossLinkActiveCount | 1.3.6.1.4.1.7262.2.2.8.2.24 | Counter | RO | mandatory | |||||||||
scalar · Counter · read-only · mandatory Indicates the time (in secs) since this alarm exist. | |||||||||||||
| NhzOduNetworkInterfaceAlarms | 1.3.6.1.4.1.7262.2.2.8.3 | ||||||||||||
| NhzOduEnetPort1Alarms | 1.3.6.1.4.1.7262.2.2.8.3.1 | ||||||||||||
| ShzOduEnetPort1DroppedEnetFramesThresholdExceeded | 1.3.6.1.4.1.7262.2.2.8.3.1.1 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory The threshold for number of frames dropped has been exceeded. The threshold and the number of seconds that it must exceed this threshold are programmed by the user.
| |||||||||||||
| ShzOduEnetPort1DroppedEnetFramesThresholdCount | 1.3.6.1.4.1.7262.2.2.8.3.1.2 | Counter | RO | mandatory | |||||||||
scalar · Counter · read-only · mandatory Indicates the approximate time, in seconds, that this alarm has been in the active state | |||||||||||||
| ShzOduEnetPort1BandwidthUtilizationThresholdExceeded | 1.3.6.1.4.1.7262.2.2.8.3.1.3 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory The threshold for the percentage of available bandwidth has been exceeded. The threshold and the number of seconds that it must exceed this threshold are programmed by the user.
| |||||||||||||
| ShzOduEnetPort1BandwidthUtilizationThresholdCount | 1.3.6.1.4.1.7262.2.2.8.3.1.4 | Counter | RO | mandatory | |||||||||
scalar · Counter · read-only · mandatory Indicates the approximate time, in seconds, that this alarm has been in the active state | |||||||||||||
| ShzOduEnetPort1RlsMismatch | 1.3.6.1.4.1.7262.2.2.8.3.1.5 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory RLS configurations on the pair of systems are mismatched.
| |||||||||||||
| ShzOduEnetPort1RlsMismatchCount | 1.3.6.1.4.1.7262.2.2.8.3.1.6 | Counter | RO | mandatory | |||||||||
scalar · Counter · read-only · mandatory Indicates the approximate time, in seconds, that this alarm has been in the active state | |||||||||||||
| ShzOduEnetPort1RLSShutdownActivated | 1.3.6.1.4.1.7262.2.2.8.3.1.7 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory RLS shutdown is activated.
| |||||||||||||
| ShzOduEnetPort1RLSShutdownActivatedCount | 1.3.6.1.4.1.7262.2.2.8.3.1.8 | Counter | RO | mandatory | |||||||||
scalar · Counter · read-only · mandatory Indicates the approximate time, in seconds, that this alarm has been in the active state | |||||||||||||
| ShzOduEnetPort1EthernetLinkDown | 1.3.6.1.4.1.7262.2.2.8.3.1.9 | INTEGER | RO | mandatory | off(1) | ||||||||
scalar · INTEGER · read-only · mandatory Indicates whether the Ethernet link is down or not. The severity is major, the probable cause is an incorrect configuration of the switch or router connected to horizon. The recommended course of action is to check the connection.
Example values from LibreNMS test devices
| |||||||||||||
| ShzOduEnetPort1EthernetLinkDownActivatedCount | 1.3.6.1.4.1.7262.2.2.8.3.1.10 | Counter | RO | mandatory | 1 | ||||||||
scalar · Counter · read-only · mandatory Indicates the approximate time, in seconds, that this alarm has been in the active state Example values from LibreNMS test devices
| |||||||||||||
| NhzOduEnetPort2Alarms | 1.3.6.1.4.1.7262.2.2.8.3.2 | ||||||||||||
| ShzOduEnetPort2EthernetLinkDown | 1.3.6.1.4.1.7262.2.2.8.3.2.1 | INTEGER | RO | mandatory | off(1) | ||||||||
scalar · INTEGER · read-only · mandatory Indicates whether the Ethernet link is down or not. The severity is major, the probable cause is an incorrect configuration of the switch or router connected to horizon. The recommended course of action is to check the connection.
Example values from LibreNMS test devices
| |||||||||||||
| ShzOduEnetPort2EthernetLinkDownActivatedCount | 1.3.6.1.4.1.7262.2.2.8.3.2.2 | Counter | RO | mandatory | 0 | ||||||||
scalar · Counter · read-only · mandatory Indicates the approximate time, in seconds, that this alarm has been in the active state Example values from LibreNMS test devices
| |||||||||||||
| NhzOduWirelessInterfaceAlarms | 1.3.6.1.4.1.7262.2.2.8.4 | ||||||||||||
| NhzOduModem1Alarms | 1.3.6.1.4.1.7262.2.2.8.4.4 | ||||||||||||
| ShzOduModem1RxLossOfSignal | 1.3.6.1.4.1.7262.2.2.8.4.4.1 | INTEGER | RO | mandatory | off(1) | ||||||||
scalar · INTEGER · read-only · mandatory Loss of signal lock from the demodulator. The severity is critical, the probable cause is lost synchronization with the far end, and recommended course of action is to check the operational state of both ends of the link.
Example values from LibreNMS test devices
| |||||||||||||
| ShzOduModem1RxLossOfSignalCount | 1.3.6.1.4.1.7262.2.2.8.4.4.2 | Counter | RO | mandatory | 73 | ||||||||
scalar · Counter · read-only · mandatory Indicates the approximate number of seconds that this alarm has been active. Example values from LibreNMS test devices
| |||||||||||||
| ShzOduModem1TxLossOfSync | 1.3.6.1.4.1.7262.2.2.8.4.4.3 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory Loss of sync bytes at the input of the modulator. The severity is critical, the probable cause is physical interference in the air link, and recommended course of action is to check the line of site between the horizon nodes.
| |||||||||||||
| ShzOduModem1TxLossOfSyncCount | 1.3.6.1.4.1.7262.2.2.8.4.4.4 | Counter | RO | mandatory | |||||||||
scalar · Counter · read-only · mandatory Indicates the approximate number of seconds that this alarm has been active. | |||||||||||||
| ShzOduModem1SnrBelowThreshold | 1.3.6.1.4.1.7262.2.2.8.4.4.5 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory The demodulator SNR performance worse than programmed levels. The severity is major, the probable cause is physical interference in the air link path or misalignment of the radios or severe weather conditions, and recommended course of action is to check the line of site between the horizon nodes.
| |||||||||||||
| ShzOduModem1SnrBelowThresholdCount | 1.3.6.1.4.1.7262.2.2.8.4.4.6 | Counter | RO | mandatory | |||||||||
scalar · Counter · read-only · mandatory Indicates the approximate number of seconds that this alarm has been active. | |||||||||||||
| ShzOduModem1EqualizerStressExceedThreshold | 1.3.6.1.4.1.7262.2.2.8.4.4.7 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory Equalizer Stress measured within the demodulator exceeds the threshold value.
| |||||||||||||
| ShzOduModem1EquilizerStressExceedThresholdCount | 1.3.6.1.4.1.7262.2.2.8.4.4.8 | Counter | RO | mandatory | |||||||||
scalar · Counter · read-only · mandatory Indicates the approximate number of seconds that this alarm has been active. | |||||||||||||
| ShzOduModem1HardwareFault | 1.3.6.1.4.1.7262.2.2.8.4.4.9 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory
| |||||||||||||
| ShzOduModem1HardwareFaultCount | 1.3.6.1.4.1.7262.2.2.8.4.4.10 | Counter | RO | mandatory | |||||||||
scalar · Counter · read-only · mandatory Indicates the approximate number of seconds that this alarm has been active. | |||||||||||||
| ShzOduModem1ProgrammingError | 1.3.6.1.4.1.7262.2.2.8.4.4.11 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory Encountered some problem while programming the modem.
| |||||||||||||
| ShzOduModem1ProgrammingErrorCount | 1.3.6.1.4.1.7262.2.2.8.4.4.12 | Counter | RO | mandatory | |||||||||
scalar · Counter · read-only · mandatory Indicates the approximate number of seconds that this alarm has been active. | |||||||||||||
| NhzOduRadio1Alarms | 1.3.6.1.4.1.7262.2.2.8.4.5 | ||||||||||||
| ShzOduRadio1SynthLostLock | 1.3.6.1.4.1.7262.2.2.8.4.5.1 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory Loss of signal lock from IF Synthesizer.
| |||||||||||||
| ShzOduRadio1SynthLostLockCount | 1.3.6.1.4.1.7262.2.2.8.4.5.2 | Counter | RO | mandatory | |||||||||
scalar · Counter · read-only · mandatory Indicates the number of seconds that Loss of signal lock from IF Synthesizer. | |||||||||||||
| ShzOduRadio1TempCompCalTableNotAvail | 1.3.6.1.4.1.7262.2.2.8.4.5.3 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory Temp comp table not available.
| |||||||||||||
| ShzOduRadio1TempCompCalTableNotAvailCount | 1.3.6.1.4.1.7262.2.2.8.4.5.4 | Counter | RO | mandatory | |||||||||
scalar · Counter · read-only · mandatory Indicates the number of seconds that Temp comp table not available. | |||||||||||||
| ShzOduRadio1TxDetectorPwrBelowThresh | 1.3.6.1.4.1.7262.2.2.8.4.5.5 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory Tx power detector below threshold 1.
| |||||||||||||
| ShzOduRadio1TxDetectorPwrBelowThreshCount | 1.3.6.1.4.1.7262.2.2.8.4.5.6 | Counter | RO | mandatory | |||||||||
scalar · Counter · read-only · mandatory Indicates the number of seconds that Tx power detector below threshold 1. | |||||||||||||
| ShzOduRadio1DrainCurrentOutOfLimit | 1.3.6.1.4.1.7262.2.2.8.4.5.7 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory Radio current1 out of limits.
| |||||||||||||
| ShzOduRadio1DrainCurrentOutOfLimitCount | 1.3.6.1.4.1.7262.2.2.8.4.5.8 | Counter | RO | mandatory | |||||||||
scalar · Counter · read-only · mandatory Indicates the number of seconds that Radio current1 out of limits. | |||||||||||||
| ShzOduRadio1TemperatureOutOfLimit | 1.3.6.1.4.1.7262.2.2.8.4.5.9 | INTEGER | RO | mandatory | off(1) | ||||||||
scalar · INTEGER · read-only · mandatory Radio temperature out of limits.
Example values from LibreNMS test devices
| |||||||||||||
| ShzOduRadio1TemperatureOutOfLimitCount | 1.3.6.1.4.1.7262.2.2.8.4.5.10 | Counter | RO | mandatory | 0 | ||||||||
scalar · Counter · read-only · mandatory Indicates the number of seconds that Radio temperature out of limits. Example values from LibreNMS test devices
| |||||||||||||
| NhzOduTraps | 1.3.6.1.4.1.7262.2.2.9 | ||||||||||||
| !hzOduExplicitAuthenticationFailureV1Trap | 1.3.6.1.4.1.7262.2.2.9.0.3 | ||||||||||||
notification Authentication of the peer horizon node has failed. The severity is critical, the probable cause is an incorrect authentication configuration on horizon faulty cable between the modem and radio, and recommended course of action is to check both ends of the link. | |||||||||||||
| !hzOduExplicitAuthenticationFailureClearedV1Trap | 1.3.6.1.4.1.7262.2.2.9.0.4 | ||||||||||||
notification The condition has cleared. The peer node is now authenticated. | |||||||||||||
| !hzOduAamConfigMisMatchV1Trap | 1.3.6.1.4.1.7262.2.2.9.0.5 | ||||||||||||
notification Adaptive modulation configuration mismatch | |||||||||||||
| !hzOduAamConfigMisMatchClearV1Trap | 1.3.6.1.4.1.7262.2.2.9.0.6 | ||||||||||||
notification Adaptive modulation configuration mismatch cleared | |||||||||||||
| !hzOduAamActiveV1Trap | 1.3.6.1.4.1.7262.2.2.9.0.7 | ||||||||||||
notification Adaptive modulation on and system running on lowest modulation | |||||||||||||
| !hzOduAamActiveClearedV1Trap | 1.3.6.1.4.1.7262.2.2.9.0.8 | ||||||||||||
notification Adaptive modulation on system running on higher modulation | |||||||||||||
| !hzOduAtpcConfigMismatchV1Trap | 1.3.6.1.4.1.7262.2.2.9.0.9 | ||||||||||||
notification ATPC is set to on at near end however in the far end it is set to off. | |||||||||||||
| !hzOduAtpcConfigMismatchClearedV1Trap | 1.3.6.1.4.1.7262.2.2.9.0.10 | ||||||||||||
notification ATPC configuration mismatch is cleared | |||||||||||||
| !hzOduSntpServersUnreachableV1Trap | 1.3.6.1.4.1.7262.2.2.9.0.11 | ||||||||||||
notification Can't reach any of the sntp servers | |||||||||||||
| !hzOduSntpServersUnreachableClearedV1Trap | 1.3.6.1.4.1.7262.2.2.9.0.12 | ||||||||||||
notification At least one of SNTP servers is reachable | |||||||||||||
| !hzOduFrequencyFileInvalidV1Trap | 1.3.6.1.4.1.7262.2.2.9.0.13 | ||||||||||||
notification When the executing frequency file is invalid, this trap is generated. | |||||||||||||
| !hzOduEnetPort1DroppedFramesThresholdExceededV1Trap | 1.3.6.1.4.1.7262.2.2.9.0.14 | ||||||||||||
notification The ethernet dropped frames threshold has been detected above its threshold value. | |||||||||||||
| !hzOduEnetPort1DroppedFramesThresholdExceededClearedV1Trap | 1.3.6.1.4.1.7262.2.2.9.0.15 | ||||||||||||
notification The condition has cleared.The ethernet dropped frames threshold is now below its threshold value. | |||||||||||||
| !hzOduEnetPort1BwUtilizationThresholdExceededV1Trap | 1.3.6.1.4.1.7262.2.2.9.0.16 | ||||||||||||
notification The ethernet bandwidth threshold has been detected above its threshold value. | |||||||||||||
| !hzOduEnetPort1BwUtilizationThresholdExceededClearedV1Trap | 1.3.6.1.4.1.7262.2.2.9.0.17 | ||||||||||||
notification The condition has cleared. The ethernet bandwidth threshold is now below its threshold value. | |||||||||||||
| !hzOduEnetPort1RlsMismatchV1Trap | 1.3.6.1.4.1.7262.2.2.9.0.18 | ||||||||||||
notification RLS mismatch | |||||||||||||
| !hzOduEnetPort1RlsMismatchClearedV1Trap | 1.3.6.1.4.1.7262.2.2.9.0.19 | ||||||||||||
notification RLS mismatch cleared | |||||||||||||
| !hzOduEnetPort1RlsShutdownActivatedv1Trap | 1.3.6.1.4.1.7262.2.2.9.0.20 | ||||||||||||
notification RLS shutdown is activated | |||||||||||||
| !hzOduEnetPort1RlsShutdownActivatedClearedV1Trap | 1.3.6.1.4.1.7262.2.2.9.0.21 | ||||||||||||
notification RLS shutdown is not activated | |||||||||||||
| !hzOduModem1RxLossOfSignalLockV1Trap | 1.3.6.1.4.1.7262.2.2.9.0.22 | ||||||||||||
notification Loss of signal lock from the demodulator. The severity is critical, the probable cause is lost synchronization with the far end, and recommended course of action is to check the operational state of both ends of the link. | |||||||||||||
| !hzOduModem1RxLossOfSignalLockClearedV1Trap | 1.3.6.1.4.1.7262.2.2.9.0.23 | ||||||||||||
notification The condition has cleared. The demodulator is synchronized. | |||||||||||||
| !hzOduModem1TxLossOfSyncV1Trap | 1.3.6.1.4.1.7262.2.2.9.0.24 | ||||||||||||
notification Loss of sync bytes at the input of the modulator. The severity is critical, the probable cause is physical interference in the air link, and recommended course of action is to check the line of site between the horizon nodes. | |||||||||||||
| !hzOduModem1TxLossOfSyncClearedV1Trap | 1.3.6.1.4.1.7262.2.2.9.0.25 | ||||||||||||
notification Tx Loss of sync bytes cleared. | |||||||||||||
| !hzOduModem1SnrBelowThresholdV1Trap | 1.3.6.1.4.1.7262.2.2.9.0.26 | ||||||||||||
notification The demodulator SNR performance worse than programmed levels. The severity is major, the probable cause is physical interference in the air link path or misalignment of the radios or severe weather conditions, and recommended course of action is to check the line of site between the horizon nodes. | |||||||||||||
| !hzOduModem1SnrBelowThresholdClearedV1Trap | 1.3.6.1.4.1.7262.2.2.9.0.27 | ||||||||||||
notification SNR performance back to normal. | |||||||||||||
| !hzOduModem1EqualizerStressExceedThresholdV1Trap | 1.3.6.1.4.1.7262.2.2.9.0.28 | ||||||||||||
notification Equalizer Stress measured within the demodulator exceeds the threshold value. | |||||||||||||
| !hzOduModem1EqualizerStressExceedThresholdClearedV1Trap | 1.3.6.1.4.1.7262.2.2.9.0.29 | ||||||||||||
notification Equalizer Stress measured within the demodulator is within the threshold value. | |||||||||||||
| !hzOduEnetPort1ChannelizedRslBelowThresholdV1Trap | 1.3.6.1.4.1.7262.2.2.9.0.30 | ||||||||||||
notification The RSL has been detected below its minimum threshold. | |||||||||||||
| !hzOduEnetPort1ChannelizedRslBelowThresholdClearedV1Trap | 1.3.6.1.4.1.7262.2.2.9.0.31 | ||||||||||||
notification The condition has cleared. RSL is now above its minimum threshold. | |||||||||||||
| !hzOduModem1HardwareFaultV1Trap | 1.3.6.1.4.1.7262.2.2.9.0.32 | ||||||||||||
notification Power supply circuitry failed. Should be sent for diagnosis. | |||||||||||||
| !hzOduModem1HardwareFaultClearedV1Trap | 1.3.6.1.4.1.7262.2.2.9.0.33 | ||||||||||||
notification Power supply circuitry is in good condition. | |||||||||||||
| !hzOduModem1ProgrammingErrorV1Trap | 1.3.6.1.4.1.7262.2.2.9.0.34 | ||||||||||||
notification Encountered problem while programming modem. | |||||||||||||
| !hzOduModem1ProgrammingErrorClearedrV1Trap | 1.3.6.1.4.1.7262.2.2.9.0.35 | ||||||||||||
notification Problem encountered while programming modem is gone. | |||||||||||||
| !hzOduRadio1SynthLostLockV1Trap | 1.3.6.1.4.1.7262.2.2.9.0.36 | ||||||||||||
notification IF synth Lock is lost. | |||||||||||||
| !hzOduRadio1SynthLostLockClearedV1Trap | 1.3.6.1.4.1.7262.2.2.9.0.37 | ||||||||||||
notification IF synth Lock is lost cleared. | |||||||||||||
| !hzOduRadio1TempCompCalTableNotAvailableV1Trap | 1.3.6.1.4.1.7262.2.2.9.0.38 | ||||||||||||
notification Temp comp table not available. | |||||||||||||
| !hzOduRadio1TempCompCalTableNotAvailableClearedV1Trap | 1.3.6.1.4.1.7262.2.2.9.0.39 | ||||||||||||
notification Temp comp table not available cleared. | |||||||||||||
| !hzOduRadio1TxDetectorPwrBelowThreshV1Trap | 1.3.6.1.4.1.7262.2.2.9.0.40 | ||||||||||||
notification Tx power detector below threshold. | |||||||||||||
| !hzOduRadio1TxDetectorPwrBelowThreshClearedV1Trap | 1.3.6.1.4.1.7262.2.2.9.0.41 | ||||||||||||
notification Tx power detector below threshold cleared. | |||||||||||||
| !hzOduRadio1DrainCurrentOutOfLimitV1Trap | 1.3.6.1.4.1.7262.2.2.9.0.42 | ||||||||||||
notification Radio current out of limits. | |||||||||||||
| !hzOduRadio1DrainCurrentOutOfLimitClearedV1Trap | 1.3.6.1.4.1.7262.2.2.9.0.43 | ||||||||||||
notification Radio current out of limits cleared. | |||||||||||||
| !hzOduRadio1TemperatureOutOfLimitV1Trap | 1.3.6.1.4.1.7262.2.2.9.0.44 | ||||||||||||
notification Radio temperature out of limits. | |||||||||||||
| !hzOduRadio1TemperatureOutOfLimitClearedV1Trap | 1.3.6.1.4.1.7262.2.2.9.0.45 | ||||||||||||
notification Radio temperature out of limits cleared. | |||||||||||||
| !hzOduTtySessionCommencedV1Trap | 1.3.6.1.4.1.7262.2.2.9.0.46 | ||||||||||||
notification A person has successfully gained access to the ascii management port (telnet, local management port, or HTTP). The username is included in the Trap. | |||||||||||||
| !hzOduTtySessionTerminatedV1Trap | 1.3.6.1.4.1.7262.2.2.9.0.47 | ||||||||||||
notification A person has logged out of an ascii management port (telnet, local management port, or HTTP). The username is included in the Trap. | |||||||||||||
| !hzOduAtpcTxAtCoordinatedPwrV1Trap | 1.3.6.1.4.1.7262.2.2.9.0.48 | ||||||||||||
notification Atpc is enabled in the system and it is transmitting at maximum power. | |||||||||||||
| !hzOduAtpcTxAtCoordinatedPwrClearedV1Trap | 1.3.6.1.4.1.7262.2.2.9.0.49 | ||||||||||||
notification Atpc is enabled in the system and it is back to regular power. | |||||||||||||
| !hzOduPartnerRedundancyModeMismatchV1Trap | 1.3.6.1.4.1.7262.2.2.9.0.50 | ||||||||||||
notification Hsb partner redundancy mode mismatch. | |||||||||||||
| !hzOduPartnerRedundancyModeMismatchClearedV1Trap | 1.3.6.1.4.1.7262.2.2.9.0.51 | ||||||||||||
notification Hsb partner redundancy mode mismatch is cleared. | |||||||||||||
| !hzOduPartnerConfigurationMismatchV1Trap | 1.3.6.1.4.1.7262.2.2.9.0.52 | ||||||||||||
notification Hsb partner configuration mismatch. | |||||||||||||
| !hzOduPartnerConfigurationMismatchClearedV1Trap | 1.3.6.1.4.1.7262.2.2.9.0.53 | ||||||||||||
notification Hsb partner configuration mismatch is cleared. | |||||||||||||
| !hzOduHsbActiveOnSecondaryV1Trap | 1.3.6.1.4.1.7262.2.2.9.0.54 | ||||||||||||
notification Hsb active on secondary. | |||||||||||||
| !hzOduHsbActiveOnSecondaryClearedV1Trap | 1.3.6.1.4.1.7262.2.2.9.0.55 | ||||||||||||
notification Hsb active on secondary is cleared. | |||||||||||||
| !hzOduHsbOverrideByUserV1Trap | 1.3.6.1.4.1.7262.2.2.9.0.56 | ||||||||||||
notification Hsb override by user. | |||||||||||||
| !hzOduHsbOverrideByUserClearedV1Trap | 1.3.6.1.4.1.7262.2.2.9.0.57 | ||||||||||||
notification Hsb active on secondary is cleared. | |||||||||||||
| !hzOduHsbCrossLinkV1Trap | 1.3.6.1.4.1.7262.2.2.9.0.58 | ||||||||||||
notification Hsb cross link by user. | |||||||||||||
| !hzOduHsbCrossLinkClearedV1Trap | 1.3.6.1.4.1.7262.2.2.9.0.59 | ||||||||||||
notification Hsb cross link is cleared. | |||||||||||||
| !hzOduHsbActiveOnPrimaryV1Trap | 1.3.6.1.4.1.7262.2.2.9.0.60 | ||||||||||||
notification Hsb active on primary. | |||||||||||||
| !hzOduHsbActiveOnPrimaryClearedV1Trap | 1.3.6.1.4.1.7262.2.2.9.0.61 | ||||||||||||
notification Hsb active on primary is cleared. | |||||||||||||
| ThzOduSnmpTrapHostTable | 1.3.6.1.4.1.7262.2.2.9.1 | NA | mandatory | ||||||||||
table · not-accessible · mandatory Table containing SNMP trap host entries. | |||||||||||||
| RhzOduSnmpTrapHostEntry | 1.3.6.1.4.1.7262.2.2.9.1.1 | NA | mandatory | ||||||||||
row · not-accessible · mandatory The snmp trap host entry containing all the trap host information | |||||||||||||
| ChzOduSnmpTrapHostIndex | 1.3.6.1.4.1.7262.2.2.9.1.1.1 | INTEGER | RO | mandatory | |||||||||
column · INTEGER · read-only · mandatory A unique value for each trap host. | |||||||||||||
| ChzOduSnmpTrapHostMode | 1.3.6.1.4.1.7262.2.2.9.1.1.2 | INTEGER | RO | mandatory | |||||||||
column · INTEGER · read-only · mandatory Indicates how the snmp trap host is obtained for the system.
| |||||||||||||
| ChzOduSnmpTrapHostIpAddress | 1.3.6.1.4.1.7262.2.2.9.1.1.3 | IpAddress | RO | mandatory | |||||||||
column · IpAddress · read-only · mandatory Indicates snmp trap host IP address. | |||||||||||||
| ChzOduSnmpTrapHostCommunityName | 1.3.6.1.4.1.7262.2.2.9.1.1.4 | DisplayString (SIZE (0..24)) | RO | mandatory | |||||||||
column · DisplayString (SIZE (0..24)) · read-only · mandatory The community string name used in Traps. | |||||||||||||
| ChzOduSnmpTrapHostActivated | 1.3.6.1.4.1.7262.2.2.9.1.1.5 | INTEGER | RO | mandatory | |||||||||
column · INTEGER · read-only · mandatory Specifies whether traps are to be sent to this specific host or not
| |||||||||||||
| ThzOduSnmpV3TrapHostsTable | 1.3.6.1.4.1.7262.2.2.9.2 | NA | mandatory | ||||||||||
table · not-accessible · mandatory Table containing snmp V3 trap host entries | |||||||||||||
| RhzOduSnmpV3TrapHostsEntry | 1.3.6.1.4.1.7262.2.2.9.2.1 | NA | mandatory | ||||||||||
row · not-accessible · mandatory Contains the snmp v3 trap host information | |||||||||||||
| ChzOduSnmpV3TrapHostsIndex | 1.3.6.1.4.1.7262.2.2.9.2.1.1 | INTEGER | RO | mandatory | |||||||||
column · INTEGER · read-only · mandatory A unique value for each v3 trap host. | |||||||||||||
| CsnmpV3TrapHostIpAddress | 1.3.6.1.4.1.7262.2.2.9.2.1.2 | IpAddress | RO | mandatory | |||||||||
column · IpAddress · read-only · mandatory Indicates snmp trap host IP address. | |||||||||||||
| CsnmpV3TrapHostUserName | 1.3.6.1.4.1.7262.2.2.9.2.1.3 | DisplayString (SIZE (0..24)) | RO | mandatory | |||||||||
column · DisplayString (SIZE (0..24)) · read-only · mandatory The user name of the v3 trap host. | |||||||||||||
| CsnmpV3TrapHostAuthProtocol | 1.3.6.1.4.1.7262.2.2.9.2.1.4 | INTEGER | RO | mandatory | |||||||||
column · INTEGER · read-only · mandatory The authentication alogorithm used by the v3 trap host.
| |||||||||||||
| CsnmpV3TrapHostAuthPassword | 1.3.6.1.4.1.7262.2.2.9.2.1.5 | DisplayString (SIZE (0..24)) | RO | mandatory | |||||||||
column · DisplayString (SIZE (0..24)) · read-only · mandatory The authentication password of the v3 trap host. | |||||||||||||
| CsnmpV3TrapHostPrivProtocol | 1.3.6.1.4.1.7262.2.2.9.2.1.6 | INTEGER | RO | mandatory | |||||||||
column · INTEGER · read-only · mandatory The privacy encryiption alogorithm used by the v3 trap host.
| |||||||||||||
| CsnmpV3TrapHostPrivPassword | 1.3.6.1.4.1.7262.2.2.9.2.1.7 | DisplayString (SIZE (0..24)) | RO | mandatory | |||||||||
column · DisplayString (SIZE (0..24)) · read-only · mandatory The privacy password of the v3 trap host. | |||||||||||||
| CsnmpV3TrapHostActivated | 1.3.6.1.4.1.7262.2.2.9.2.1.8 | INTEGER | RO | mandatory | |||||||||
column · INTEGER · read-only · mandatory Specifies whether a specific v3 trap host is allowed to access the system
| |||||||||||||
| ShzOduColdStartTrap | 1.3.6.1.4.1.7262.2.2.9.3 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory Specifies whether this trap is to be sent or not
| |||||||||||||
| ShzOduLinkDownTrap | 1.3.6.1.4.1.7262.2.2.9.4 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory Specifies whether this trap is to be sent or not
| |||||||||||||
| ShzOduLinkUpTrap | 1.3.6.1.4.1.7262.2.2.9.5 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory Specifies whether this trap is to be sent or not
| |||||||||||||
| ShzOduExplicitAuthenticationFailureTrap | 1.3.6.1.4.1.7262.2.2.9.6 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory Specifies whether this trap is to be sent or not
| |||||||||||||
| ShzOduAamConfigMismatchTrap | 1.3.6.1.4.1.7262.2.2.9.7 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory Enables or disables the aamConfigMismatch trap.
| |||||||||||||
| ShzOduAamActiveTrap | 1.3.6.1.4.1.7262.2.2.9.8 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory Enables or disables the aamActive trap.
| |||||||||||||
| ShzOduAtpcConfigMismatchTrap | 1.3.6.1.4.1.7262.2.2.9.9 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory Enables or disables the trap.
| |||||||||||||
| ShzOduSntpServersUnreachableTrap | 1.3.6.1.4.1.7262.2.2.9.10 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory Enables or disables the trap.
| |||||||||||||
| ShzOduFrequencyFileInvalidTrap | 1.3.6.1.4.1.7262.2.2.9.11 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory Enables or disables the trap.
| |||||||||||||
| ShzOduEnetPort1DroppedFramesThresholdExceedTrap | 1.3.6.1.4.1.7262.2.2.9.12 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory Enables or disables the trap. This trap, if enabled, will be sent when the dropped ethernet frames threshold is exceeded. If enabled, the system will send this trap to all trap hosts programmed in the system by the user.
| |||||||||||||
| ShzOduEnetPort1BandwidthUtilizationThresholdExceedTrap | 1.3.6.1.4.1.7262.2.2.9.13 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory Enables or disables the trap. This trap, if enabled, will be sent when the ethernet bandwidth utilization threshold is exceeded. If enabled, the system will send this trap to all trap hosts programmed in the system by the user.
| |||||||||||||
| ShzOduEnetPort1RlsMismatchTrap | 1.3.6.1.4.1.7262.2.2.9.14 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory Enables or disables the trap.
| |||||||||||||
| ShzOduEnetPort1RLSShutdownActivatedTrap | 1.3.6.1.4.1.7262.2.2.9.15 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory Enables or disables the trap.
| |||||||||||||
| ShzOduModem1RxLossOfSignalLockTrap | 1.3.6.1.4.1.7262.2.2.9.16 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory Specifies whether this trap is to be sent or not
| |||||||||||||
| ShzOduModem1TxLossOfSyncTrap | 1.3.6.1.4.1.7262.2.2.9.17 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory Specifies whether this trap is to be sent or not
| |||||||||||||
| ShzOduModem1SnrBelowThresholdTrap | 1.3.6.1.4.1.7262.2.2.9.18 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory Specifies whether this trap is to be sent or not
| |||||||||||||
| ShzOduModem1EqualizerStressExceedThresholdTrap | 1.3.6.1.4.1.7262.2.2.9.19 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory Specifies whether this trap is to be sent or not
| |||||||||||||
| ShzOduModem1ChannelizedRslBelowThresholdTrap | 1.3.6.1.4.1.7262.2.2.9.20 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory Enables or disables the trap. This trap, if enabled, will be sent when the radio receive signal level threshold is exceeded. If enabled, the system will send this trap to all trap hosts programmed in the system by the user.
| |||||||||||||
| ShzOduModem1HardwareFaultTrap | 1.3.6.1.4.1.7262.2.2.9.21 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory Specifies whether this trap is to be sent or not
| |||||||||||||
| ShzOduModem1ProgrammingErrorTrap | 1.3.6.1.4.1.7262.2.2.9.22 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory Specifies whether this trap is to be sent or not
| |||||||||||||
| ShzOduRadio1SynthLostLockTrap | 1.3.6.1.4.1.7262.2.2.9.23 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory Enables or disables the ifSythLostLock trap.
| |||||||||||||
| ShzOduRadio1TempCompCalTableNotAvailTrap | 1.3.6.1.4.1.7262.2.2.9.24 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory Enables or disables the tempCompCalTableNotAvailable trap.
| |||||||||||||
| ShzOduRadio1TxDetectorPwrBelowThreshTrap | 1.3.6.1.4.1.7262.2.2.9.25 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory Enables or disables the txDetectorPwrBelowThresh trap.
| |||||||||||||
| ShzOduRadio1DrainCurrentOutOfLimitTrap | 1.3.6.1.4.1.7262.2.2.9.26 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory Enables or disables the radioCurrentOutOfLimitTrap trap.
| |||||||||||||
| ShzOduRadio1TemperatureOutOfLimitTrap | 1.3.6.1.4.1.7262.2.2.9.27 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory Enables or disables the radioTemperatureOutOfLimitTrap trap.
| |||||||||||||
| ShzOduTtyManagementSessionCommencedTrap | 1.3.6.1.4.1.7262.2.2.9.28 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory Specifies whether this trap is to be sent or not
| |||||||||||||
| ShzOduTtyManagementSessionTerminatedTrap | 1.3.6.1.4.1.7262.2.2.9.29 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory Specifies whether this trap is to be sent or not
| |||||||||||||
| ShzOduAtpcAutoDisabledTrap | 1.3.6.1.4.1.7262.2.2.9.30 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory Specifies whether this trap is to be sent or not
| |||||||||||||
| ShzOduPartnerRedundancyModeMismatchTrap | 1.3.6.1.4.1.7262.2.2.9.31 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory Specifies whether this trap is to be sent or not
| |||||||||||||
| ShzOduPartnerConfigurationMismatchTrap | 1.3.6.1.4.1.7262.2.2.9.32 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory Specifies whether this trap is to be sent or not
| |||||||||||||
| ShzOduHsbActiveOnSecondaryTrap | 1.3.6.1.4.1.7262.2.2.9.33 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory Specifies whether this trap is to be sent or not
| |||||||||||||
| ShzOduHsbOverrideByUserTrap | 1.3.6.1.4.1.7262.2.2.9.34 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory Specifies whether this trap is to be sent or not
| |||||||||||||
| ShzOduHsbCrossLinkTrap | 1.3.6.1.4.1.7262.2.2.9.35 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory Specifies whether this trap is to be sent or not
| |||||||||||||
| ShzOduHsbActiveOnPrimaryTrap | 1.3.6.1.4.1.7262.2.2.9.36 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory Specifies whether this trap is to be sent or not
| |||||||||||||
| NhzOduSnmp | 1.3.6.1.4.1.7262.2.2.10 | ||||||||||||
| ShzOduSnmpUserAccess | 1.3.6.1.4.1.7262.2.2.10.1 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory Specifies the user access to the system.If access is set to managers then only managers with there ip addresses set in snmpManagersTable will be able to gain snmp access to the system. If access is set to any then any manager will be able to gain snmp access to the system
| |||||||||||||
| ShzOduSnmpManagerAnyCommunityName | 1.3.6.1.4.1.7262.2.2.10.2 | DisplayString (SIZE (0..24)) | RO | mandatory | |||||||||
scalar · DisplayString (SIZE (0..24)) · read-only · mandatory The community string name used by the 'any' manager. | |||||||||||||
| ShzOduSnmpSetRequests | 1.3.6.1.4.1.7262.2.2.10.3 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory Indicates whether SNMP SET requests are allowed.
| |||||||||||||
| ThzOduSnmpManagersTable | 1.3.6.1.4.1.7262.2.2.10.4 | NA | mandatory | ||||||||||
table · not-accessible · mandatory Table containing snmp manager entries | |||||||||||||
| RhzOduSnmpManagersEntry | 1.3.6.1.4.1.7262.2.2.10.4.1 | NA | mandatory | ||||||||||
| ChzOduSnmpManagersIndex | 1.3.6.1.4.1.7262.2.2.10.4.1.1 | INTEGER | RO | mandatory | |||||||||
column · INTEGER · read-only · mandatory A unique value for each manager. | |||||||||||||
| ChzOduSnmpManagerIpAddress | 1.3.6.1.4.1.7262.2.2.10.4.1.2 | IpAddress | RO | mandatory | |||||||||
column · IpAddress · read-only · mandatory The IP address of the Manager. | |||||||||||||
| ChzOduSnmpManagerCommunityName | 1.3.6.1.4.1.7262.2.2.10.4.1.3 | DisplayString (SIZE (0..24)) | RO | mandatory | |||||||||
column · DisplayString (SIZE (0..24)) · read-only · mandatory The community string name used by the manager. | |||||||||||||
| ChzOduSnmpManagerActivated | 1.3.6.1.4.1.7262.2.2.10.4.1.4 | INTEGER | RO | mandatory | |||||||||
column · INTEGER · read-only · mandatory Specifies whether a specific manager is allowed to access the system
| |||||||||||||
| ThzOduSnmpV3ManagersTable | 1.3.6.1.4.1.7262.2.2.10.5 | NA | mandatory | ||||||||||
table · not-accessible · mandatory Table containing snmp V3 manager entries | |||||||||||||
| RhzOduSnmpV3ManagersEntry | 1.3.6.1.4.1.7262.2.2.10.5.1 | NA | mandatory | ||||||||||
row · not-accessible · mandatory Contains the snmp v3 manager information | |||||||||||||
| ChzOduSnmpV3ManagersIndex | 1.3.6.1.4.1.7262.2.2.10.5.1.1 | INTEGER | RO | mandatory | |||||||||
column · INTEGER · read-only · mandatory A unique value for each v3 manager. | |||||||||||||
| ChzOduSnmpV3ManagerUserName | 1.3.6.1.4.1.7262.2.2.10.5.1.2 | DisplayString (SIZE (0..24)) | RO | mandatory | |||||||||
column · DisplayString (SIZE (0..24)) · read-only · mandatory The user name of the v3 Manager. | |||||||||||||
| ChzOduSnmpV3ManagerAuthProtocol | 1.3.6.1.4.1.7262.2.2.10.5.1.3 | INTEGER | RO | mandatory | |||||||||
column · INTEGER · read-only · mandatory The authentication alogorithm used by the v3 manager.
| |||||||||||||
| ChzOduSnmpV3ManagerAuthPassword | 1.3.6.1.4.1.7262.2.2.10.5.1.4 | DisplayString (SIZE (0..24)) | RO | mandatory | |||||||||
column · DisplayString (SIZE (0..24)) · read-only · mandatory The authentication password of the v3 Manager. | |||||||||||||
| ChzOduSnmpV3ManagerPrivProtocol | 1.3.6.1.4.1.7262.2.2.10.5.1.5 | INTEGER | RO | mandatory | |||||||||
column · INTEGER · read-only · mandatory The privacy encryiption alogorithm used by the v3 manager.
| |||||||||||||
| ChzOduSnmpV3ManagerPrivPassword | 1.3.6.1.4.1.7262.2.2.10.5.1.6 | DisplayString (SIZE (0..24)) | RO | mandatory | |||||||||
column · DisplayString (SIZE (0..24)) · read-only · mandatory The privacy password of the v3 Manager. | |||||||||||||
| ChzOduSnmpV3ManagerActivated | 1.3.6.1.4.1.7262.2.2.10.5.1.7 | INTEGER | RO | mandatory | |||||||||
column · INTEGER · read-only · mandatory Specifies whether a specific v3 manager is allowed to access the system
| |||||||||||||
| NhzOduManagementSessions | 1.3.6.1.4.1.7262.2.2.11 | ||||||||||||
| NhzOduTtySessionUser1 | 1.3.6.1.4.1.7262.2.2.11.1 | ||||||||||||
| ShzOduTtySessionUser1Name | 1.3.6.1.4.1.7262.2.2.11.1.1 | DisplayString (SIZE (0..32)) | RO | mandatory | |||||||||
scalar · DisplayString (SIZE (0..32)) · read-only · mandatory The username of a management session using Telnet or HTTP. The session state variable must be checked to determine if the management session is currently in progress. | |||||||||||||
| ShzOduTtySessionUser1ConnectionType | 1.3.6.1.4.1.7262.2.2.11.1.2 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory The physical port used to log in to the system. The serial port is always local to the equipment. The 10BaseT connector may be local, or remote, depending on if the configuration of network management port. The inband connection is the port carrying customer traffic.
| |||||||||||||
| ShzOduTtySessionUser1State | 1.3.6.1.4.1.7262.2.2.11.1.3 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory The state of the session. The session is inProgress if the user is currently logged into the system. The session is terminated if the user has logged out of the system.
| |||||||||||||
| NhzOduTtySessionUser2 | 1.3.6.1.4.1.7262.2.2.11.2 | ||||||||||||
| ShzOduTtySessionUser2Name | 1.3.6.1.4.1.7262.2.2.11.2.1 | DisplayString (SIZE (0..32)) | RO | mandatory | |||||||||
scalar · DisplayString (SIZE (0..32)) · read-only · mandatory The username of a person currently logged in to the system using Telnet or HTTP. This can be in-band or the side 10BT channel, if supported on this system. | |||||||||||||
| ShzOduTtySessionUser2ConnectionType | 1.3.6.1.4.1.7262.2.2.11.2.2 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory The physical port used to log in to the system. The serial port is always local to the equipment. The 10BaseT connector may be local, or remote, depending on if the configuration of network management port. The inband connection is the port carrying customer traffic.
| |||||||||||||
| ShzOduTtySessionUser2State | 1.3.6.1.4.1.7262.2.2.11.2.3 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory The state of the session. The session is inProgress if the user is currently logged into the system. The session is terminated if the user has logged out of the system.
| |||||||||||||
| NhzOduTtySessionUser3 | 1.3.6.1.4.1.7262.2.2.11.3 | ||||||||||||
| ShzOduTtySessionUser3Name | 1.3.6.1.4.1.7262.2.2.11.3.1 | DisplayString (SIZE (0..32)) | RO | mandatory | |||||||||
scalar · DisplayString (SIZE (0..32)) · read-only · mandatory The username of a person currently logged in to the system using Telnet or HTTP. This can be in-band or the side 10BT channel, if supported on this system. | |||||||||||||
| ShzOduTtySessionUser3ConnectionType | 1.3.6.1.4.1.7262.2.2.11.3.2 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory The physical port used to log in to the system. The serial port is always local to the equipment. The 10BaseT connector may be local, or remote, depending on if the configuration of network management port. The inband connection is the port carrying customer traffic.
| |||||||||||||
| ShzOduTtySessionUser3State | 1.3.6.1.4.1.7262.2.2.11.3.3 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory The state of the session. The session is inProgress if the user is currently logged into the system. The session is terminated if the user has logged out of the system.
| |||||||||||||
| NhzOduTtySessionUser4 | 1.3.6.1.4.1.7262.2.2.11.4 | ||||||||||||
| ShzOduTtySessionUser4Name | 1.3.6.1.4.1.7262.2.2.11.4.1 | DisplayString (SIZE (0..32)) | RO | mandatory | |||||||||
scalar · DisplayString (SIZE (0..32)) · read-only · mandatory The username of a person currently logged in to the system using Telnet or HTTP. This can be in-band or the side 10BT channel, if supported on this system. | |||||||||||||
| ShzOduTtySessionUser4ConnectionType | 1.3.6.1.4.1.7262.2.2.11.4.2 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory The physical port used to log in to the system. The serial port is always local to the equipment. The 10BaseT connector may be local, or remote, depending on if the configuration of network management port. The inband connection is the port carrying customer traffic.
| |||||||||||||
| ShzOduTtySessionUser4State | 1.3.6.1.4.1.7262.2.2.11.4.3 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory The state of the session. The session is inProgress if the user is currently logged into the system. The session is terminated if the user has logged out of the system.
| |||||||||||||
| NhzOduTtySessionUser5 | 1.3.6.1.4.1.7262.2.2.11.5 | ||||||||||||
| ShzOduTtySessionUser5Name | 1.3.6.1.4.1.7262.2.2.11.5.1 | DisplayString (SIZE (0..32)) | RO | mandatory | |||||||||
scalar · DisplayString (SIZE (0..32)) · read-only · mandatory The username of a person currently logged in to the system using Telnet or HTTP. This can be in-band or the side 10BT channel, if supported on this system. | |||||||||||||
| ShzOduTtySessionUser5ConnectionType | 1.3.6.1.4.1.7262.2.2.11.5.2 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory The physical port used to log in to the system. The serial port is always local to the equipment. The 10BaseT connector may be local, or remote, depending on if the configuration of network management port. The inband connection is the port carrying customer traffic.
| |||||||||||||
| ShzOduTtySessionUser5State | 1.3.6.1.4.1.7262.2.2.11.5.3 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory The state of the session. The session is inProgress if the user is currently logged into the system. The session is terminated if the user has logged out of the system.
| |||||||||||||
| NhzOduTtySessionUser6 | 1.3.6.1.4.1.7262.2.2.11.6 | ||||||||||||
| ShzOduTtySessionUser6Name | 1.3.6.1.4.1.7262.2.2.11.6.1 | DisplayString (SIZE (0..32)) | RO | mandatory | |||||||||
scalar · DisplayString (SIZE (0..32)) · read-only · mandatory The username of a person currently logged in to the system using Telnet or HTTP. This can be in-band or the side 10BT channel, if supported on this system. | |||||||||||||
| ShzOduTtySessionUser6ConnectionType | 1.3.6.1.4.1.7262.2.2.11.6.2 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory The physical port used to log in to the system. The serial port is always local to the equipment. The 10BaseT connector may be local, or remote, depending on if the configuration of network management port. The inband connection is the port carrying customer traffic.
| |||||||||||||
| ShzOduTtySessionUser6State | 1.3.6.1.4.1.7262.2.2.11.6.3 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory The state of the session. The session is inProgress if the user is currently logged into the system. The session is terminated if the user has logged out of the system.
| |||||||||||||
| NhzOduSessionUserInformation | 1.3.6.1.4.1.7262.2.2.11.7 | ||||||||||||
| ShzOduTtySessionUserName | 1.3.6.1.4.1.7262.2.2.11.7.1 | DisplayString (SIZE (0..32)) | RO | mandatory | |||||||||
scalar · DisplayString (SIZE (0..32)) · read-only · mandatory NOT IMPLEMENTED. Object type placeholder for username string for SNMP traps. The username of a person currently logged in to the system using Telnet or HTTP. This can be in-band or the side 10BT channel, if supported on this system. | |||||||||||||
| ShzOduTtySessionUserConnectionType | 1.3.6.1.4.1.7262.2.2.11.7.2 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory NOT IMPLEMENTED. Object type placeholder for connection type for SNMP traps. The physical port used to log in to the system. The serial port is always local to the equipment. The 10BaseT connector may be local, or remote, depending on if the configuration of network management port. The inband connection is the port carrying customer traffic.
| |||||||||||||
| NhzOduHttp | 1.3.6.1.4.1.7262.2.2.12 | ||||||||||||
| ShzOduHttpEnable | 1.3.6.1.4.1.7262.2.2.12.1 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory Indicates whether HTTP is enabled.
| |||||||||||||
| NhzOduHttpSecure | 1.3.6.1.4.1.7262.2.2.12.2 | ||||||||||||
| ShzOduHttpSecureCertificateStatus | 1.3.6.1.4.1.7262.2.2.12.2.1 | DisplayString (SIZE (0..100)) | RO | mandatory | |||||||||
scalar · DisplayString (SIZE (0..100)) · read-only · mandatory Returns the HTTPS certificate status | |||||||||||||
| ShzOduHttpSecureAccessForAdminUsers | 1.3.6.1.4.1.7262.2.2.12.2.2 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory the HTTPS access requirement for Admin user group.
| |||||||||||||
| ShzOduHttpSecureAccessForNocUsers | 1.3.6.1.4.1.7262.2.2.12.2.3 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory the HTTPS access requirement for Noc user group.
| |||||||||||||
| ShzOduHttpSecureAccessForSuperUsers | 1.3.6.1.4.1.7262.2.2.12.2.4 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory the HTTPS access requirement for Super user group.
| |||||||||||||
| NhzOduQos | 1.3.6.1.4.1.7262.2.2.13 | ||||||||||||
| ShzOduQosEnable | 1.3.6.1.4.1.7262.2.2.13.1 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory Indicates whether QOS is enabled.
| |||||||||||||
| ShzOduCosType | 1.3.6.1.4.1.7262.2.2.13.2 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory Indicates the class of service tag type. Based on the setting Horizon will use the CoS value in the VLAN tag, or Q-in-Q inner VLAN tag, Q-in-Q outer VLAN tag, or DSCP tag.
| |||||||||||||
| ShzOduCoSQinQiTag | 1.3.6.1.4.1.7262.2.2.13.3 | DisplayString | RW | mandatory | |||||||||
scalar · DisplayString · read-write · mandatory Sets the value of the Q-in-Q inner tag. This tag is also used to classify the non-Q-in-Q VLAN. Default value is 0x8100. | |||||||||||||
| ShzOduCoSQinQoTag | 1.3.6.1.4.1.7262.2.2.13.4 | DisplayString | RW | mandatory | |||||||||
scalar · DisplayString · read-write · mandatory Sets the value of the Q-in-Q outer VLAN tag. Default value is 0x8100. | |||||||||||||
| ShzOduCosQueueMapping | 1.3.6.1.4.1.7262.2.2.13.5 | DisplayString (SIZE (15..32)) | RW | mandatory | |||||||||
scalar · DisplayString (SIZE (15..32)) · read-write · mandatory User queue assignments for CoS values 0 to 7. There are 4 coS queues. Their corresponding queue numbers are 1,2, 3, where 1 is the lowest priority queue and 4 is the highest priority queue. CoS to queue mapping example: 1 1 2 2 3 3 4 4. | |||||||||||||
| ShzOduCosExpediteQueue | 1.3.6.1.4.1.7262.2.2.13.6 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory This sets the user queue operation mode. (a) In expedite mode, any Queue can be assigned 100% of CIR. Queue 4 is serviced first and queue 1 is servcied last.(b) In non expedite mode, the sum of all CIRs must be equal to 100%. In this mode higher priority queues will be serviced first until that queue is emptied or the defined CIR is reached.
| |||||||||||||
| ShzOduCosQueueCIR | 1.3.6.1.4.1.7262.2.2.13.7 | DisplayString (SIZE (0..32)) | RW | mandatory | |||||||||
scalar · DisplayString (SIZE (0..32)) · read-write · mandatory Committeed Information Rate (CIR) assignments for CoS queues 1 to 4. CIR is assigned as the percentage of system current speed. When expedite queue is enabled any queue can be assigned 100% bandwidth. When expedite queue is disabled the sum of CIR of all queues should be 100. | |||||||||||||
| ShzOduCosQueueCBS | 1.3.6.1.4.1.7262.2.2.13.8 | DisplayString (SIZE (0..32)) | RW | mandatory | |||||||||
scalar · DisplayString (SIZE (0..32)) · read-write · mandatory Comitted Burst Size (CBS) for CoS queues 1 to 4. CBS is the percentage of total packet buffer size. The sum of CBS's of all 4 queues must be equal to 100. Minimum CBS assignable to any queue is 1. | |||||||||||||
| ShzOduCosDefaultValue | 1.3.6.1.4.1.7262.2.2.13.9 | INTEGER (0..7) | RW | mandatory | |||||||||
scalar · INTEGER (0..7) · read-write · mandatory Default CoS value assigned to the ethernet frames that don't have VLAN or Q-in-Q tag. | |||||||||||||
| ShzOduCutThroughProcessing | 1.3.6.1.4.1.7262.2.2.13.10 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory Sets cut through processing on/off.
| |||||||||||||
| NhzOduRapidLinkShutdown | 1.3.6.1.4.1.7262.2.2.14 | ||||||||||||
| NhzOduRapidLinkShutdownVer1 | 1.3.6.1.4.1.7262.2.2.14.1 | ||||||||||||
| ShzOduRlsEnable | 1.3.6.1.4.1.7262.2.2.14.1.1 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory <deprecated> The Rapid Link Shutdown feature: enabled or disabled. Changing this option requires a system reset.
| |||||||||||||
| ShzOduAutomaticLinkReestablish | 1.3.6.1.4.1.7262.2.2.14.1.2 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory <deprecated> If this feature is enabled, the link will be automatically reestablished. If this feature is disabled, the user must explicitly use the manualReestablish object to bring the link back up
| |||||||||||||
| ShzOduManualLinkReestablish | 1.3.6.1.4.1.7262.2.2.14.1.3 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory <deprecated> This object is writeable ONLY if automaticLinkReestablish is set to disabled. The user explicitly brings the link back up by setting this object to enabled. The user explicitly brings the link down by setting this object to disabled. to bring the link back up
| |||||||||||||
| ShzOduHysterisisErredFramesPerMilliSecond | 1.3.6.1.4.1.7262.2.2.14.1.4 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory <deprecated> The link will be automatically shut down when this number of erred modem frames threshold is exceeded during the time set in the hysterisisErredMilliSeconds object. **NOTE: You must SET the writeRlsMonitorParametersToSystem object to write this paramater to RAM. If you write and immediately read this object, the previous value will be displayed. You should SET all parameters in this folder first, and then write to a '1' to the writeRlsMonitorParametersToSystem object. You must also save the MIB via the writing the apSaveMIB object, and then reset the system. | |||||||||||||
| ShzOduHysterisisErredMilliSeconds | 1.3.6.1.4.1.7262.2.2.14.1.5 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory <deprecated> The time to determine a link that has excessive errors. The link will be automatically shut down when this number of milliseconds experiences the number of erred frames specified in the hysterisisErredFramesPerMilliSecond object. **NOTE: You must SET the writeRlsMonitorParametersToSystem object to write this paramater to RAM. If you write and immediately read this object, the previous value will be displayed. You should SET all parameters in this folder first, and then write to a '1' to the writeRlsMonitorParametersToSystem object. You must also save the MIB via the writing the apSaveMIB object, and then reset the system. | |||||||||||||
| ShzOduHysterisisUnerredFramesPerMilliSecond | 1.3.6.1.4.1.7262.2.2.14.1.6 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory <deprecated> The link will be automatically brought back up when the number of erred modem frames is less than this value ( only if automaticLinkReestablish is set to enabled). This threshold value cannot be crossed for the duration of time specified in the hysterisisUnerredMilliSeconds object. **NOTE: You must SET the writeRlsMonitorParametersToSystem object to write this paramater to RAM. If you write and immediately read this object, the previous value will be displayed. You should SET all parameters in this folder first, and then write to a '1' to the writeRlsMonitorParametersToSystem object. You must also save the MIB via the writing the apSaveMIB object, and then reset the system. | |||||||||||||
| ShzOduHysterisisUnerredMilliSeconds | 1.3.6.1.4.1.7262.2.2.14.1.7 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory <deprecated> The time block to use to determine if the link is error free enough to warrant it to automatically reestablish itself ( only if automaticLinkReestablish is set to enabled). The link will be brought back up automatically when this number of milliseconds experiences less the number of acceptable erred frames specified in the hysterisisUnerredFramesPerMilliSecond object. **NOTE: You must SET the writeRlsMonitorParametersToSystem object to write this paramater to RAM. If you write and immediately read this object, the previous value will be displayed. You should SET all parameters in this folder first, and then write to a '1' to the writeRlsMonitorParametersToSystem object. You must also save the MIB via the writing the apSaveMIB object, and then reset the system. | |||||||||||||
| ShzOduWriteRlsMonitorParametersToSystem | 1.3.6.1.4.1.7262.2.2.14.1.8 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory <deprecated> This writes the following parameters to RAM: hysterisisErredFramesPerMilliSecond, hysterisisErredMilliSeconds, hysterisisUnerredFramesPerMilliSecond, hysterisisUnerredMilliSeconds. Reading this object returns '1'. | |||||||||||||
| ShzOduRlsSampleTimeInMilliSeconds | 1.3.6.1.4.1.7262.2.2.14.1.9 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory <deprecated> | |||||||||||||
| NhzOduRapidLinkShutdownVer2 | 1.3.6.1.4.1.7262.2.2.14.2 | ||||||||||||
| ShzOduPrimaryRlsEnable | 1.3.6.1.4.1.7262.2.2.14.2.1 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory The Rapid Link Shutdown feature: enabled or disabled. Changing this option requires a system reset.
| |||||||||||||
| ShzOduPrimaryRlsHardFaultMonitor | 1.3.6.1.4.1.7262.2.2.14.2.2 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory This object has changed - Enable the rlsHardFaultMonitor for rapid detection of severely degrade link. When disabled the only the RLS Link Degrade Monitor is used.
| |||||||||||||
| ShzOduPrimaryAutomaticLinkReestablish | 1.3.6.1.4.1.7262.2.2.14.2.3 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory If this feature is enabled, the link will be automatically reestablished If this feature is disabled, the user must explicitly use the manualReestablish object to bring the link back up
| |||||||||||||
| ShzOduPrimaryManualLinkReestablish | 1.3.6.1.4.1.7262.2.2.14.2.4 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory This object is writeable ONLY if automaticLinkReestablish is set to disabled. The user explicitly brings the link back up by setting this object to enabled. The user explicitly brings the link down by setting this object to disabled. to bring the link back up
| |||||||||||||
| ShzOduWritePrimaryRlsMonitorParametersToSystem | 1.3.6.1.4.1.7262.2.2.14.2.5 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory This object has changed - This writes RLS soft and hard fault monitor parameters to RAM Reading this object returns '1'. | |||||||||||||
| NhzOduPrimarySoftFaultMonitor | 1.3.6.1.4.1.7262.2.2.14.2.6 | ||||||||||||
| ShzOduPrimaryEstablishErredFrameThreshold | 1.3.6.1.4.1.7262.2.2.14.2.6.1 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory Maximum erred blocks, per sample, allowed for link establishment. | |||||||||||||
| ShzOduPrimaryShutdownErredFrameThreshold | 1.3.6.1.4.1.7262.2.2.14.2.6.2 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory Minimum erred blocks, per sample, allowed before link shutdown. | |||||||||||||
| ShzOduPrimaryEstablishNumberOfSamples | 1.3.6.1.4.1.7262.2.2.14.2.6.3 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory Minimum number of consecutive good samples required before link is established. | |||||||||||||
| ShzOduPrimaryShutdownNumberOfSamples | 1.3.6.1.4.1.7262.2.2.14.2.6.4 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory Minimum number of consecutive erred samples before link is shutdown. | |||||||||||||
| ShzOduPrimaryEstablishSamplePeriod | 1.3.6.1.4.1.7262.2.2.14.2.6.5 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory Period of Time, in milliseconds, for monitoring Establish Erred Frame Threshold. | |||||||||||||
| ShzOduPrimaryShutdownSamplePeriod | 1.3.6.1.4.1.7262.2.2.14.2.6.6 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory Period of Time, in milliseconds, for monitoring Shutdown Erred Frame Threshold. | |||||||||||||
| ShzOduPrimaryQuickShutdownSamplePeriod | 1.3.6.1.4.1.7262.2.2.14.2.6.7 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory Minimum number of milliseconds required to classify samples as erred. | |||||||||||||
| NhzOduPrimaryHardFaultMonitor | 1.3.6.1.4.1.7262.2.2.14.2.7 | ||||||||||||
| ShzOduPrimaryFaultSamplePeriod | 1.3.6.1.4.1.7262.2.2.14.2.7.1 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory The period of time, in milliseconds, for which the rlsFaultThreshold is applied. | |||||||||||||
| ShzOduPrimaryFaultThreshold | 1.3.6.1.4.1.7262.2.2.14.2.7.2 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory The percentage of the rlsFaultSamplePeriodMilliSeconds period which must be degraded before the link is set to the 'impaired' state. | |||||||||||||
| NhzOduPrimaryReceiveSignalLevelMonitor | 1.3.6.1.4.1.7262.2.2.14.2.8 | ||||||||||||
| ShzOduPrimaryRlsMakeRslMonitorRslValue | 1.3.6.1.4.1.7262.2.2.14.2.8.1 | DisplayString (SIZE (0..24)) | RW | mandatory | |||||||||
scalar · DisplayString (SIZE (0..24)) · read-write · mandatory The RSL threshold, in dBm. When Link is inactive and if RSL is higher than this threshold for a desired period, the link will become active. | |||||||||||||
| ShzOduPrimaryRlsMakeRslMonitorPeriod | 1.3.6.1.4.1.7262.2.2.14.2.8.2 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory The desired period, in seconds. When Link is inactive and if RSL is higher than the desired threshold for this period, the link will become active. | |||||||||||||
| NhzOduPrimaryRlsStatus | 1.3.6.1.4.1.7262.2.2.14.2.9 | ||||||||||||
| ShzOduPrimaryRlsOption | 1.3.6.1.4.1.7262.2.2.14.2.9.1 | DisplayString | RO | mandatory | |||||||||
scalar · DisplayString · read-only · mandatory RLS Option. On Basic: RLS enabled with base degrade monitoring; On Advanced: RLS enabled with hard fault monitoring; Off: Entire RLS feature disabled. | |||||||||||||
| ShzOduPrimaryRlsState | 1.3.6.1.4.1.7262.2.2.14.2.9.2 | DisplayString | RO | mandatory | |||||||||
scalar · DisplayString · read-only · mandatory Rapid Link Shutdown State. If the state is activated, that means link is down; If the state is inactivated, that means that link is up. | |||||||||||||
| ShzOduPrimaryRlsMismatchState | 1.3.6.1.4.1.7262.2.2.14.2.9.3 | DisplayString | RO | mandatory | |||||||||
scalar · DisplayString · read-only · mandatory RLS Mismatch State. If the state is activated, that means RLS configuration is mismatched with peer. If the state is OK, that means RLS configuration is matched with peer. | |||||||||||||
| ShzOduPrimaryDegradeMonitorState | 1.3.6.1.4.1.7262.2.2.14.2.9.4 | DisplayString | RO | mandatory | |||||||||
scalar · DisplayString · read-only · mandatory Degrade Monitor State. If the state is activated, that means the RLS Degrade Monitor is asserting the link down. If the state is OK, that means the RLS Degrade Monitor is asserting the link up. | |||||||||||||
| ShzOduPrimaryHardFaultMonitorState | 1.3.6.1.4.1.7262.2.2.14.2.9.5 | DisplayString | RO | mandatory | |||||||||
scalar · DisplayString · read-only · mandatory Hard Fault Monitor State. If the state is activated, that means the Hard Fault Monitor is asserting the link down. If the state is OK, that means the RLS Hard Fault Monitor is asserting the link up. | |||||||||||||
| ShzOduPrimaryMakeRslThresholdState | 1.3.6.1.4.1.7262.2.2.14.2.9.6 | DisplayString | RO | mandatory | |||||||||
scalar · DisplayString · read-only · mandatory Make RSL Threshold State. If the state is not met, that means the RLS signal level is below the threshold value. If the state is OK, that means the RLS signal level is above the threshold value. | |||||||||||||
| ShzOduPrimaryPeerRslState | 1.3.6.1.4.1.7262.2.2.14.2.9.7 | DisplayString | RO | mandatory | |||||||||
scalar · DisplayString · read-only · mandatory Peer RSL State. If the state is activated, that means the peer has activated RLS. If the state is OK, that means the Peer hasn't activated RLS. | |||||||||||||
| ShzOduPrimaryRadioInterfaceState | 1.3.6.1.4.1.7262.2.2.14.2.9.8 | DisplayString | RO | mandatory | |||||||||
scalar · DisplayString · read-only · mandatory Radio Interface State. If the state is down, that means The radio interface is not operational(muted,disconnected, not configured). If the state is up, that means the radio interface is operational. | |||||||||||||
| ShzOduPrimaryNetworkInterfaceState | 1.3.6.1.4.1.7262.2.2.14.2.9.9 | DisplayString | RO | mandatory | |||||||||
scalar · DisplayString · read-only · mandatory Network Interface State. If the state is down, that means the network interface (Ethernet/PHY) is not operational(disconnected, not configured). If the state is up, that means the network interface (Ethernet/PHY) is operational. | |||||||||||||
| ShzOduPrimaryUserConfiguredEstablishFer | 1.3.6.1.4.1.7262.2.2.14.2.9.10 | DisplayString | RO | mandatory | |||||||||
scalar · DisplayString · read-only · mandatory User Configured Establish Frame Error Ratio required for the link to be restored to service, set by the user. An example value being '1.0E-7'. | |||||||||||||
| ShzOduPrimaryMinimumAchievableEstablishFer | 1.3.6.1.4.1.7262.2.2.14.2.9.11 | DisplayString | RO | mandatory | |||||||||
scalar · DisplayString · read-only · mandatory Minimum achievable Frame Error Ratio required for the link to be restored to service. An example value being '1.0E-7'. | |||||||||||||
| ShzOduPrimaryUserConfiguredShutdownFer | 1.3.6.1.4.1.7262.2.2.14.2.9.12 | DisplayString | RO | mandatory | |||||||||
scalar · DisplayString · read-only · mandatory User Configured Shutdown Frame Error Ratio required for the link to remain in-service, set by the user. An example value being '1.0E-7'. | |||||||||||||
| ShzOduPrimaryMinimumAchievableShutdownFer | 1.3.6.1.4.1.7262.2.2.14.2.9.13 | DisplayString | RO | mandatory | |||||||||
scalar · DisplayString · read-only · mandatory Minimum achievable Frame Error Ratio required for the link to remain in-service. An example value being '1.0E-7'. | |||||||||||||
| ShzOduPrimaryUserConfiguredEstablishMonitorTime | 1.3.6.1.4.1.7262.2.2.14.2.9.14 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory User Configured Establish Monitor Time, in milliseconds, for which the 'User Configured Establish FER' must be achieved to bring link into service, set by user | |||||||||||||
| ShzOduPrimaryActualEstablishMonitorTime | 1.3.6.1.4.1.7262.2.2.14.2.9.15 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory Actual Establish Monitor Time, in milliseconds, for which the 'User Configured Establish FER' must be achieved to bring link into service, it's a multiple of the establish sample period required to observe the FER | |||||||||||||
| ShzOduPrimaryUserConfiguredShutdownMonitorTime | 1.3.6.1.4.1.7262.2.2.14.2.9.16 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory User Configured Shutdown Monitor Time, in milliseconds, for which the 'User Configured Shutdown FER' must be met for the link to remain in-service, set by user. | |||||||||||||
| ShzOduPrimaryActualShutdownMonitorTime | 1.3.6.1.4.1.7262.2.2.14.2.9.17 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory Actual Shutdown Monitor Time, in milliseconds, for which the 'User Configured Shutdown FER' must be met for the link to remain in-service, it's a multiple of the shutdown sample period required to observe the FER | |||||||||||||
| NhzOduSntp | 1.3.6.1.4.1.7262.2.2.15 | ||||||||||||
| ShzOduSntpEnable | 1.3.6.1.4.1.7262.2.2.15.1 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory Indicates whether SNTP feature is enabled.
| |||||||||||||
| ShzOduSntpOffset | 1.3.6.1.4.1.7262.2.2.15.2 | INTEGER (-140..140) | RW | mandatory | |||||||||
scalar · INTEGER (-140..140) · read-write · mandatory System time offset from GMT. | |||||||||||||
| ThzOduSntpServerTable | 1.3.6.1.4.1.7262.2.2.15.3 | NA | mandatory | ||||||||||
table · not-accessible · mandatory Table containing sntp server entries | |||||||||||||
| RhzOduSntpServerEntry | 1.3.6.1.4.1.7262.2.2.15.3.1 | NA | mandatory | ||||||||||
| ChzOduSntpServerIndex | 1.3.6.1.4.1.7262.2.2.15.3.1.1 | INTEGER | RO | mandatory | |||||||||
column · INTEGER · read-only · mandatory A unique value for each server. | |||||||||||||
| ChzOduSntpServerIpAddress | 1.3.6.1.4.1.7262.2.2.15.3.1.2 | IpAddress | RW | mandatory | |||||||||
column · IpAddress · read-write · mandatory The IP address of the server. | |||||||||||||
| ChzOduSntpServerStatus | 1.3.6.1.4.1.7262.2.2.15.3.1.3 | INTEGER | RO | mandatory | |||||||||
column · INTEGER · read-only · mandatory The status of the sntp server.
| |||||||||||||
| ChzOduSntpServerStratum | 1.3.6.1.4.1.7262.2.2.15.3.1.4 | INTEGER | RO | mandatory | |||||||||
column · INTEGER · read-only · mandatory Specifies the stratum of a server, 0 for failed server | |||||||||||||
| NhzOduLogs | 1.3.6.1.4.1.7262.2.2.16 | ||||||||||||
| ShzOduEventLogEnable | 1.3.6.1.4.1.7262.2.2.16.1 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory Indicates whether event log is enabled.
| |||||||||||||
| ShzOduPerfmLogEnable | 1.3.6.1.4.1.7262.2.2.16.2 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory Indicates whether performance log is enabled.
| |||||||||||||
| ShzOduPerfmLogInterval | 1.3.6.1.4.1.7262.2.2.16.3 | DisplayString (SIZE (0..10)) | RW | mandatory | |||||||||
scalar · DisplayString (SIZE (0..10)) · read-write · mandatory Performance statistics are logged periodically by this interval. | |||||||||||||
| NhzOduRadius | 1.3.6.1.4.1.7262.2.2.17 | ||||||||||||
| ShzOduRadiusSuperUserAuthentication | 1.3.6.1.4.1.7262.2.2.17.1 | INTEGER | RW | mandatory | |||||||||
scalar · INTEGER · read-write · mandatory The set strict mode on or off
| |||||||||||||
| ShzOduRadiusServerTimeOut | 1.3.6.1.4.1.7262.2.2.17.2 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory Timeout period for authentication requests | |||||||||||||
| ShzOduRadiusServerDeadTime | 1.3.6.1.4.1.7262.2.2.17.3 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory Time to declare an unresponsive server 'dead' | |||||||||||||
| ShzOduRadiusServerReTransmit | 1.3.6.1.4.1.7262.2.2.17.4 | INTEGER | RO | mandatory | |||||||||
scalar · INTEGER · read-only · mandatory Maximum number of retransmits to an unresponsive server
| |||||||||||||
| ThzOduRadiusServerTable | 1.3.6.1.4.1.7262.2.2.17.5 | NA | mandatory | ||||||||||
table · not-accessible · mandatory Table containing radius server entries | |||||||||||||
| RhzOduRadiusServerEntry | 1.3.6.1.4.1.7262.2.2.17.5.1 | NA | mandatory | ||||||||||
| ChzOduRadiusServerIndex | 1.3.6.1.4.1.7262.2.2.17.5.1.1 | INTEGER | RO | mandatory | |||||||||
column · INTEGER · read-only · mandatory A unique value for each server. | |||||||||||||
| ChzOduRadiusCfgdHostIpAddress | 1.3.6.1.4.1.7262.2.2.17.5.1.2 | IpAddress | RW | mandatory | |||||||||
column · IpAddress · read-write · mandatory The IP address of the configured radius server. | |||||||||||||
| ChzOduRadiusActiveHostIpAddress | 1.3.6.1.4.1.7262.2.2.17.5.1.3 | IpAddress | RO | mandatory | |||||||||
column · IpAddress · read-only · mandatory The IP address of the active radius server. | |||||||||||||
Traps / Notifications
- coldStart
1.3.6.1.2.1.11.0.0 - hzOduAamActiveClearedV1Trap
1.3.6.1.4.1.7262.2.2.9.0.8 - hzOduAamActiveV1Trap
1.3.6.1.4.1.7262.2.2.9.0.7 - hzOduAamConfigMisMatchClearV1Trap
1.3.6.1.4.1.7262.2.2.9.0.6 - hzOduAamConfigMisMatchV1Trap
1.3.6.1.4.1.7262.2.2.9.0.5 - hzOduAtpcConfigMismatchClearedV1Trap
1.3.6.1.4.1.7262.2.2.9.0.10 - hzOduAtpcConfigMismatchV1Trap
1.3.6.1.4.1.7262.2.2.9.0.9 - hzOduAtpcTxAtCoordinatedPwrClearedV1Trap
1.3.6.1.4.1.7262.2.2.9.0.49 - hzOduAtpcTxAtCoordinatedPwrV1Trap
1.3.6.1.4.1.7262.2.2.9.0.48 - hzOduEnetPort1BwUtilizationThresholdExceededClearedV1Trap
1.3.6.1.4.1.7262.2.2.9.0.17 - hzOduEnetPort1BwUtilizationThresholdExceededV1Trap
1.3.6.1.4.1.7262.2.2.9.0.16 - hzOduEnetPort1ChannelizedRslBelowThresholdClearedV1Trap
1.3.6.1.4.1.7262.2.2.9.0.31 - hzOduEnetPort1ChannelizedRslBelowThresholdV1Trap
1.3.6.1.4.1.7262.2.2.9.0.30 - hzOduEnetPort1DroppedFramesThresholdExceededClearedV1Trap
1.3.6.1.4.1.7262.2.2.9.0.15 - hzOduEnetPort1DroppedFramesThresholdExceededV1Trap
1.3.6.1.4.1.7262.2.2.9.0.14 - hzOduEnetPort1RlsMismatchClearedV1Trap
1.3.6.1.4.1.7262.2.2.9.0.19 - hzOduEnetPort1RlsMismatchV1Trap
1.3.6.1.4.1.7262.2.2.9.0.18 - hzOduEnetPort1RlsShutdownActivatedClearedV1Trap
1.3.6.1.4.1.7262.2.2.9.0.21 - hzOduEnetPort1RlsShutdownActivatedv1Trap
1.3.6.1.4.1.7262.2.2.9.0.20 - hzOduExplicitAuthenticationFailureClearedV1Trap
1.3.6.1.4.1.7262.2.2.9.0.4 - hzOduExplicitAuthenticationFailureV1Trap
1.3.6.1.4.1.7262.2.2.9.0.3 - hzOduFrequencyFileInvalidV1Trap
1.3.6.1.4.1.7262.2.2.9.0.13 - hzOduHsbActiveOnPrimaryClearedV1Trap
1.3.6.1.4.1.7262.2.2.9.0.61 - hzOduHsbActiveOnPrimaryV1Trap
1.3.6.1.4.1.7262.2.2.9.0.60 - hzOduHsbActiveOnSecondaryClearedV1Trap
1.3.6.1.4.1.7262.2.2.9.0.55 - hzOduHsbActiveOnSecondaryV1Trap
1.3.6.1.4.1.7262.2.2.9.0.54 - hzOduHsbCrossLinkClearedV1Trap
1.3.6.1.4.1.7262.2.2.9.0.59 - hzOduHsbCrossLinkV1Trap
1.3.6.1.4.1.7262.2.2.9.0.58 - hzOduHsbOverrideByUserClearedV1Trap
1.3.6.1.4.1.7262.2.2.9.0.57 - hzOduHsbOverrideByUserV1Trap
1.3.6.1.4.1.7262.2.2.9.0.56 - hzOduModem1EqualizerStressExceedThresholdClearedV1Trap
1.3.6.1.4.1.7262.2.2.9.0.29 - hzOduModem1EqualizerStressExceedThresholdV1Trap
1.3.6.1.4.1.7262.2.2.9.0.28 - hzOduModem1HardwareFaultClearedV1Trap
1.3.6.1.4.1.7262.2.2.9.0.33 - hzOduModem1HardwareFaultV1Trap
1.3.6.1.4.1.7262.2.2.9.0.32 - hzOduModem1ProgrammingErrorClearedrV1Trap
1.3.6.1.4.1.7262.2.2.9.0.35 - hzOduModem1ProgrammingErrorV1Trap
1.3.6.1.4.1.7262.2.2.9.0.34 - hzOduModem1RxLossOfSignalLockClearedV1Trap
1.3.6.1.4.1.7262.2.2.9.0.23 - hzOduModem1RxLossOfSignalLockV1Trap
1.3.6.1.4.1.7262.2.2.9.0.22 - hzOduModem1SnrBelowThresholdClearedV1Trap
1.3.6.1.4.1.7262.2.2.9.0.27 - hzOduModem1SnrBelowThresholdV1Trap
1.3.6.1.4.1.7262.2.2.9.0.26 - hzOduModem1TxLossOfSyncClearedV1Trap
1.3.6.1.4.1.7262.2.2.9.0.25 - hzOduModem1TxLossOfSyncV1Trap
1.3.6.1.4.1.7262.2.2.9.0.24 - hzOduPartnerConfigurationMismatchClearedV1Trap
1.3.6.1.4.1.7262.2.2.9.0.53 - hzOduPartnerConfigurationMismatchV1Trap
1.3.6.1.4.1.7262.2.2.9.0.52 - hzOduPartnerRedundancyModeMismatchClearedV1Trap
1.3.6.1.4.1.7262.2.2.9.0.51 - hzOduPartnerRedundancyModeMismatchV1Trap
1.3.6.1.4.1.7262.2.2.9.0.50 - hzOduRadio1DrainCurrentOutOfLimitClearedV1Trap
1.3.6.1.4.1.7262.2.2.9.0.43 - hzOduRadio1DrainCurrentOutOfLimitV1Trap
1.3.6.1.4.1.7262.2.2.9.0.42 - hzOduRadio1SynthLostLockClearedV1Trap
1.3.6.1.4.1.7262.2.2.9.0.37 - hzOduRadio1SynthLostLockV1Trap
1.3.6.1.4.1.7262.2.2.9.0.36 - hzOduRadio1TempCompCalTableNotAvailableClearedV1Trap
1.3.6.1.4.1.7262.2.2.9.0.39 - hzOduRadio1TempCompCalTableNotAvailableV1Trap
1.3.6.1.4.1.7262.2.2.9.0.38 - hzOduRadio1TemperatureOutOfLimitClearedV1Trap
1.3.6.1.4.1.7262.2.2.9.0.45 - hzOduRadio1TemperatureOutOfLimitV1Trap
1.3.6.1.4.1.7262.2.2.9.0.44 - hzOduRadio1TxDetectorPwrBelowThreshClearedV1Trap
1.3.6.1.4.1.7262.2.2.9.0.41 - hzOduRadio1TxDetectorPwrBelowThreshV1Trap
1.3.6.1.4.1.7262.2.2.9.0.40 - hzOduSntpServersUnreachableClearedV1Trap
1.3.6.1.4.1.7262.2.2.9.0.12 - hzOduSntpServersUnreachableV1Trap
1.3.6.1.4.1.7262.2.2.9.0.11 - hzOduTtySessionCommencedV1Trap
1.3.6.1.4.1.7262.2.2.9.0.46 - hzOduTtySessionTerminatedV1Trap
1.3.6.1.4.1.7262.2.2.9.0.47 - linkDown
1.3.6.1.2.1.11.0.1 - linkUp
1.3.6.1.2.1.11.0.2