SLE-MPLS-TP-TUNNEL-MIB
DASAN Co.,LTD.Copyright (C) The Internet Society (2004). The initial version of this MIB module was published in RFC 3812. For full legal notices see the RFC itself or see: http://www.ietf.org/copyrights/ianamib.html This MIB module contains managed object definitions for MPLS Traffic Engineering (TE) as defined in: 1. Extensions to RSVP for LSP Tunnels, Awduche et al, RFC 3209, December 2001 2. Constraint-Based LSP Setup using LDP, Jamoussi (Editor), RFC 3212, January 2002 3. Requirements for Traffic Engineering Over MPLS, Awduche, D., Malcolm, J., Agogbua, J., O'Dell, M., and J. McManus, [RFC2702], September 1999
snmptranslate -m SLE-MPLS-TP-TUNNEL-MIB -Tpsnmpwalk -v2c -c <community> -m SLE-MPLS-TP-TUNNEL-MIB <host> 1.3.6.1.4.1.6296.101.16.14Imports
| DASAN-SMI | sleMgmt |
|---|---|
| IF-MIB | InterfaceIndexOrZero, ifCounterDiscontinuityGroup, ifGeneralInformationGroup |
| MPLS-TC-EXT-STD-MIB | MplsCcId, MplsIccId |
| MPLS-TC-STD-MIB | MplsLabel, mplsStdMIB |
| SLE-TC-MIB | SleControlRequestResultType, SleControlStatusType |
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP |
| SNMPv2-SMI | Bits, Gauge32, Integer32, IpAddress, MODULE-IDENTITY, MibIdentifier, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, iso, zeroDotZero |
| SNMPv2-TC | DisplayString, MacAddress, PhysAddress, TEXTUAL-CONVENTION |
OID tree
| Name | OID | Type | Access | Status |
|---|---|---|---|---|
| NsleMpls | 1.3.6.1.4.1.6296.101.16 | |||
node · current SLE MPLS. | ||||
| IsleMplsTpTunnel | 1.3.6.1.4.1.6296.101.16.14 | |||
identity Copyright (C) The Internet Society (2004). The initial version of this MIB module was published in RFC 3812. For full legal notices see the RFC itself or see: http://www.ietf.org/copyrights/ianamib.html This MIB module contains managed object definitions for MPLS Traffic Engineering (TE) as defined in: 1. Extensions to RSVP for LSP Tunnels, Awduche et al, RFC 3209, December 2001 2. Constraint-Based LSP Setup using LDP, Jamoussi (Editor), RFC 3212, January 2002 3. Requirements for Traffic Engineering Over MPLS, Awduche, D., Malcolm, J., Agogbua, J., O'Dell, M., and J. McManus, [RFC2702], September 1999 | ||||
| NsleMplsTpTunnelCfg | 1.3.6.1.4.1.6296.101.16.14.1 | |||
| TsleMplsTpTunnelCfgInfoTable | 1.3.6.1.4.1.6296.101.16.14.1.1 | NA | ||
table · not-accessible · current The mplsTunnelTable allows new MPLS tunnels to be created between an LSR and a remote endpoint, and existing tunnels to be reconfigured or removed. Note that only point-to-point tunnel segments are supported, although multipoint-to-point and point- to-multipoint connections are supported by an LSR acting as a cross-connect. Each MPLS tunnel can thus have one out-segment originating at this LSR and/or one in-segment terminating at this LSR. | ||||
| RsleMplsTpTunnelCfgInfoEntry | 1.3.6.1.4.1.6296.101.16.14.1.1.1 | NA | ||
row · not-accessible · current An entry in this table represents an MPLS tunnel. An entry can be created by a network administrator or by an SNMP agent as instructed by an MPLS signalling protocol. Whenever a new entry is created with mplsTunnelIsIf set to true(1), then a corresponding entry is created in ifTable as well (see RFC 2863). The ifType of this entry is mplsTunnel(150). A tunnel entry needs to be uniquely identified across a MPLS network. Indices mplsTunnelIndex and mplsTunnelInstance uniquely identify a tunnel on the LSR originating the tunnel. To uniquely identify a tunnel across an MPLS network requires index mplsTunnelIngressLSRId. The last index mplsTunnelEgressLSRId is useful in identifying all instances of a tunnel that terminate on the same egress LSR. | ||||
| CsleMplsTpTunnelCfgInfoIndex | 1.3.6.1.4.1.6296.101.16.14.1.1.1.1 | Unsigned32 (0..65535) | NA | |
column · Unsigned32 (0..65535) · not-accessible · current A unique value which identify an entry in this table. | ||||
| CsleMplsTpTunnelCfgInfoName | 1.3.6.1.4.1.6296.101.16.14.1.1.1.2 | OCTET STRING (SIZE (0..16)) | RO | |
column · OCTET STRING (SIZE (0..16)) · read-only · current The canonical name assigned to the tunnel. This name can be used to refer to the tunnel on the LSR's console port. If mplsTunnelIsIf is set to true then the ifName of the interface corresponding to this tunnel should have a value equal to mplsTunnelName. Also see the description of ifName in RFC 2863. | ||||
| CsleMplsTpTunnelCfgInfoId | 1.3.6.1.4.1.6296.101.16.14.1.1.1.3 | Unsigned32 (1..65535) | RO | |
column · Unsigned32 (1..65535) · read-only · current Uniquely identifies a set of tunnel instances between a pair of ingress and egress LSRs. Managers should obtain new values for row creation in this table by reading mplsTunnelIndexNext. When the MPLS signalling protocol is rsvp(2) this value SHOULD be equal to the value signaled in the Tunnel Id of the Session object. When the MPLS signalling protocol is crldp(3) this value SHOULD be equal to the value signaled in the LSP ID. | ||||
| CsleMplsTpTunnelCfgInfoSrcIdType | 1.3.6.1.4.1.6296.101.16.14.1.1.1.4 | INTEGER | RO | |
column · INTEGER · read-only · current This object is used to set the ietf or itut type.
| ||||
| CsleMplsTpTunnelCfgInfoSrcGId | 1.3.6.1.4.1.6296.101.16.14.1.1.1.5 | Unsigned32 (1..4294967295) | RO | |
column · Unsigned32 (1..4294967295) · read-only · current This Object is used to display the GlobalID of IETF | ||||
| CsleMplsTpTunnelCfgInfoSrcCc | 1.3.6.1.4.1.6296.101.16.14.1.1.1.6 | MplsCcId | RO | |
column · MplsCcId · read-only · current This Object is used to display the Source CC-ID of ITUT | ||||
| CsleMplsTpTunnelCfgInfoSrcIcc | 1.3.6.1.4.1.6296.101.16.14.1.1.1.7 | MplsIccId | RO | |
column · MplsIccId · read-only · current This Object is used to set the Source ICC-ID of ITUT | ||||
| CsleMplsTpTunnelCfgInfoSrcNodeId | 1.3.6.1.4.1.6296.101.16.14.1.1.1.8 | IpAddress | RO | |
column · IpAddress · read-only · current This Object is used to display the Source Node ID of IETF and ITUT | ||||
| CsleMplsTpTunnelCfgInfoDestIdType | 1.3.6.1.4.1.6296.101.16.14.1.1.1.9 | INTEGER | RO | |
column · INTEGER · read-only · current This object is used to set the ietf or itut type.
| ||||
| CsleMplsTpTunnelCfgInfoDestGId | 1.3.6.1.4.1.6296.101.16.14.1.1.1.10 | Unsigned32 (1..4294967295) | RO | |
column · Unsigned32 (1..4294967295) · read-only · current This Object is used to set the Destination GlobalID of IETF | ||||
| CsleMplsTpTunnelCfgInfoDestCc | 1.3.6.1.4.1.6296.101.16.14.1.1.1.11 | MplsCcId | RO | |
column · MplsCcId · read-only · current This Object is used to display the Destination CC-ID of ITUT | ||||
| CsleMplsTpTunnelCfgInfoDestIcc | 1.3.6.1.4.1.6296.101.16.14.1.1.1.12 | MplsIccId | RO | |
column · MplsIccId · read-only · current This Object is used to set the Destination ICC-ID of ITUT | ||||
| CsleMplsTpTunnelCfgInfoDestNodeId | 1.3.6.1.4.1.6296.101.16.14.1.1.1.13 | IpAddress | RO | |
column · IpAddress · read-only · current This Object is used to display the Destination Node ID of IETF and ITUT | ||||
| CsleMplsTpTunnelCfgInfoMode | 1.3.6.1.4.1.6296.101.16.14.1.1.1.14 | INTEGER | RO | |
column · INTEGER · read-only · current This object is used to set the Tunnel Mode
| ||||
| CsleMplsTpTunnelCfgInfoFwdInLabel | 1.3.6.1.4.1.6296.101.16.14.1.1.1.15 | MplsLabel | RO | |
column · MplsLabel · read-only · current This object is used to display the Forward In Label. The lable range is 0 to 1048575. Here 0 to 15 are reserved labels. User allowed range is 16 to 1048575.. The default value 1048576 is invalid label | ||||
| CsleMplsTpTunnelCfgInfoFwdInIfIndex | 1.3.6.1.4.1.6296.101.16.14.1.1.1.16 | InterfaceIndexOrZero | RO | |
column · InterfaceIndexOrZero · read-only · current This object is used to set the Forward IN Interface index | ||||
| CsleMplsTpTunnelCfgInfoFwdOperation | 1.3.6.1.4.1.6296.101.16.14.1.1.1.17 | INTEGER | RO | |
column · INTEGER · read-only · current This object is used to set the Forward Ilm OPeration .
| ||||
| CsleMplsTpTunnelCfgInfoFwdOutLabel | 1.3.6.1.4.1.6296.101.16.14.1.1.1.18 | MplsLabel | RO | |
column · MplsLabel · read-only · current This object is used to display the Forward In Label. The lable range is 0 to 1048575. Here 0 to 15 are reserved labels. User allowed range is 16 to 1048575. The default value 1048576 is invalid label | ||||
| CsleMplsTpTunnelCfgInfoFwdOutIfIndex | 1.3.6.1.4.1.6296.101.16.14.1.1.1.19 | InterfaceIndexOrZero | RO | |
column · InterfaceIndexOrZero · read-only · current This object is used to set the Forward OUT Interface index | ||||
| CsleMplsTpTunnelCfgInfoFwdOutMac | 1.3.6.1.4.1.6296.101.16.14.1.1.1.20 | MacAddress | RO | |
column · MacAddress · read-only · current This object is used to display the Forward OUT MAC ADDRESS | ||||
| CsleMplsTpTunnelCfgInfoRevInLabel | 1.3.6.1.4.1.6296.101.16.14.1.1.1.21 | MplsLabel | RO | |
column · MplsLabel · read-only · current This object is used to display the Forward In Label. The lable range is 0 to 1048575. Here 0 to 15 are reserved labels. User allowed range is 16 to 1048575. The default value 1048576 is invalid label | ||||
| CsleMplsTpTunnelCfgInfoRevInIfIndex | 1.3.6.1.4.1.6296.101.16.14.1.1.1.22 | InterfaceIndexOrZero | RO | |
column · InterfaceIndexOrZero · read-only · current This object is used to set the Reverse IN Interface index | ||||
| CsleMplsTpTunnelCfgInfoRevOperation | 1.3.6.1.4.1.6296.101.16.14.1.1.1.23 | INTEGER | RO | |
column · INTEGER · read-only · current This object is used to set the Reverse Ilm OPeration .
| ||||
| CsleMplsTpTunnelCfgInfoRevOutLabel | 1.3.6.1.4.1.6296.101.16.14.1.1.1.24 | MplsLabel | RO | |
column · MplsLabel · read-only · current This object is used to display the Forward In Label. The lable range is 0 to 1048575. Here 0 to 15 are reserved labels. User allowed range is 16 to 1048575. The default value 1048576 is invalid label | ||||
| CsleMplsTpTunnelCfgInfoRevOutIfIndex | 1.3.6.1.4.1.6296.101.16.14.1.1.1.25 | InterfaceIndexOrZero | RO | |
column · InterfaceIndexOrZero · read-only · current This object is used to set the Reverse OUT Interface index | ||||
| CsleMplsTpTunnelCfgInfoRevOutMac | 1.3.6.1.4.1.6296.101.16.14.1.1.1.26 | MacAddress | RO | |
column · MacAddress · read-only · current This object is used to display the Forward OUT MAC ADDRESS . | ||||
| CsleMplsTpTunnelCfgInfoState | 1.3.6.1.4.1.6296.101.16.14.1.1.1.27 | INTEGER | RO | |
column · INTEGER · read-only · current This object is to display status of the tunnel.
| ||||
| CsleMplsTpTunnelCfgInfoRole | 1.3.6.1.4.1.6296.101.16.14.1.1.1.28 | INTEGER | RO | |
column · INTEGER · read-only · current This object is to display Role of the tunnel.
| ||||
| CsleMplsTpTunnelCfgInfoAssociateTnlName | 1.3.6.1.4.1.6296.101.16.14.1.1.1.29 | OCTET STRING | RO | |
column · OCTET STRING · read-only · current This object to display associate of reverse tunnel. | ||||
| CsleMplsTpTunnelCfgInfoDescription | 1.3.6.1.4.1.6296.101.16.14.1.1.1.30 | OCTET STRING | RO | |
column · OCTET STRING · read-only · current Description. | ||||
| CsleMplsTpTunnelCfgInfoHlspRole | 1.3.6.1.4.1.6296.101.16.14.1.1.1.31 | INTEGER | RO | |
column · INTEGER · read-only · current This object is used to set the Hlsp Tunnel. whether the tunnel is Server or client. server (1) :- To set the Server Tunnel client(2) :- To set the Client Tunnel .
| ||||
| CsleMplsTpTunnelCfgInfoHlspServerTunnelName | 1.3.6.1.4.1.6296.101.16.14.1.1.1.32 | OCTET STRING | RO | |
column · OCTET STRING · read-only · current This object is used to set the server TunnelName, when sleMplsTpTunnelCfgControlHlspOption as a client . | ||||
| CsleMplsTpTunnelCfgInfoQosPolicyName | 1.3.6.1.4.1.6296.101.16.14.1.1.1.33 | OCTET STRING | RO | |
column · OCTET STRING · read-only · current This object is used to set the Qos Policy name. | ||||
| NsleMplsTpTunnelCfgControl | 1.3.6.1.4.1.6296.101.16.14.1.2 | |||
| SsleMplsTpTunnelCfgControlRequest | 1.3.6.1.4.1.6296.101.16.14.1.2.1 | INTEGER | RW | |
scalar · INTEGER · read-write · current This object holds the possible read-write columns that can be modified in the Tunnel table. For each read-write column of Tunnel table, a Set Operation controlvalue is added in this object.
| ||||
| SsleMplsTpTunnelCfgControlStatus | 1.3.6.1.4.1.6296.101.16.14.1.2.2 | SleControlStatusType | RO | |
scalar · SleControlStatusType · read-only · current This object displays the status of the configuration done. | ||||
| SsleMplsTpTunnelCfgControlTimer | 1.3.6.1.4.1.6296.101.16.14.1.2.3 | Gauge32 | RW | |
scalar · Gauge32 · read-write · current This object is based on the SLE style where a timer is configured for every control table. | ||||
| SsleMplsTpTunnelCfgControlTimeStamp | 1.3.6.1.4.1.6296.101.16.14.1.2.4 | TimeTicks | RO | |
scalar · TimeTicks · read-only · current This object specifies the time at which the configuration is done. | ||||
| SsleMplsTpTunnelCfgControlReqResult | 1.3.6.1.4.1.6296.101.16.14.1.2.5 | SleControlRequestResultType | RO | |
scalar · SleControlRequestResultType · read-only · current The standard result of the SET operation is stored here. | ||||
| SsleMplsTpTunnelCfgControlName | 1.3.6.1.4.1.6296.101.16.14.1.2.6 | OCTET STRING (SIZE (0..16)) | RW | |
scalar · OCTET STRING (SIZE (0..16)) · read-write · current The canonical name assigned to the tunnel. This name can be used to refer to the tunnel on the LSR's console port. If mplsTunnelIsIf is set to true then the ifName of the interface corresponding to this tunnel should have a value equal to SlemplsTunnelName. Also see the description of ifName in RFC 2863. | ||||
| SsleMplsTpTunnelCfgControlId | 1.3.6.1.4.1.6296.101.16.14.1.2.7 | Unsigned32 (1..65535) | RW | |
scalar · Unsigned32 (1..65535) · read-write · current This object is used to set the tunnel Id . | ||||
| SsleMplsTpTunnelCfgControlSrcIdType | 1.3.6.1.4.1.6296.101.16.14.1.2.8 | INTEGER | RW | |
scalar · INTEGER · read-write · current This object is used to set the ietf or itut type.
| ||||
| SsleMplsTpTunnelCfgControlSrcGId | 1.3.6.1.4.1.6296.101.16.14.1.2.9 | Unsigned32 (1..4294967295) | RW | |
scalar · Unsigned32 (1..4294967295) · read-write · current This object is used to set the source Global-Id for IETF . | ||||
| SsleMplsTpTunnelCfgControlSrcCc | 1.3.6.1.4.1.6296.101.16.14.1.2.10 | MplsCcId | RW | |
scalar · MplsCcId · read-write · current This object is used to set the source CC-ID for ITUT. | ||||
| SsleMplsTpTunnelCfgControlSrcIcc | 1.3.6.1.4.1.6296.101.16.14.1.2.11 | MplsIccId | RW | |
scalar · MplsIccId · read-write · current This object is used to set the Source ICC-ID for ITUT. | ||||
| SsleMplsTpTunnelCfgControlSrcNodeId | 1.3.6.1.4.1.6296.101.16.14.1.2.12 | IpAddress | RW | |
scalar · IpAddress · read-write · current This object is used to set the Source Node-Id for IETF and ITUT | ||||
| SsleMplsTpTunnelCfgControlDestIdType | 1.3.6.1.4.1.6296.101.16.14.1.2.13 | INTEGER | RW | |
scalar · INTEGER · read-write · current This object is used to set the ietf or itut type.
| ||||
| SsleMplsTpTunnelCfgControlDestGId | 1.3.6.1.4.1.6296.101.16.14.1.2.14 | Unsigned32 (1) | RW | |
scalar · Unsigned32 (1) · read-write · current This object is used to set the Destination Global-Id for IETF . | ||||
| SsleMplsTpTunnelCfgControlDestCc | 1.3.6.1.4.1.6296.101.16.14.1.2.15 | MplsCcId | RW | |
scalar · MplsCcId · read-write · current This object is used to set the Destination CC-ID for ITUT. | ||||
| SsleMplsTpTunnelCfgControlDestIcc | 1.3.6.1.4.1.6296.101.16.14.1.2.16 | MplsIccId | RW | |
scalar · MplsIccId · read-write · current This object is used to set the Destination ICC-ID for ITUT. | ||||
| SsleMplsTpTunnelCfgControlDestNodeId | 1.3.6.1.4.1.6296.101.16.14.1.2.17 | IpAddress | RW | |
scalar · IpAddress · read-write · current This object is used to set the Destination NodeID for IETF and ITUT. | ||||
| SsleMplsTpTunnelCfgControlMode | 1.3.6.1.4.1.6296.101.16.14.1.2.18 | INTEGER | RW | |
scalar · INTEGER · read-write · current This object is used to set the Tunnel mode .
| ||||
| SsleMplsTpTunnelCfgControlPath | 1.3.6.1.4.1.6296.101.16.14.1.2.19 | INTEGER | RW | |
scalar · INTEGER · read-write · current This object is used to Set the forward path and reverse path tunnel.
| ||||
| SsleMplsTpTunnelCfgControlInLabel | 1.3.6.1.4.1.6296.101.16.14.1.2.20 | MplsLabel | RW | |
scalar · MplsLabel · read-write · current This object is used to set the Inlabel. | ||||
| SsleMplsTpTunnelCfgControlInInterface | 1.3.6.1.4.1.6296.101.16.14.1.2.21 | InterfaceIndexOrZero | RW | |
scalar · InterfaceIndexOrZero · read-write · current This object is used to set the Ininterface index. | ||||
| SsleMplsTpTunnelCfgControlOperation | 1.3.6.1.4.1.6296.101.16.14.1.2.22 | INTEGER | RW | |
scalar · INTEGER · read-write · current This object is used to set the operation of Tuunel
| ||||
| SsleMplsTpTunnelCfgControlOutLabel | 1.3.6.1.4.1.6296.101.16.14.1.2.23 | MplsLabel | RW | |
scalar · MplsLabel · read-write · current This object is used to set the outlabel. | ||||
| SsleMplsTpTunnelCfgControlOutInterface | 1.3.6.1.4.1.6296.101.16.14.1.2.24 | InterfaceIndexOrZero | RW | |
scalar · InterfaceIndexOrZero · read-write · current This object is used to set the outerinterface index. | ||||
| SsleMplsTpTunnelCfgControlOutMacAddress | 1.3.6.1.4.1.6296.101.16.14.1.2.25 | MacAddress | RW | |
scalar · MacAddress · read-write · current This object is used to Set the Out MacAddress . | ||||
| SsleMplsTpTunnelCfgControlAssociateTnlName | 1.3.6.1.4.1.6296.101.16.14.1.2.26 | OCTET STRING | RW | |
scalar · OCTET STRING · read-write · current This object is used to Associated Forward tunnel and reverse tunnel with reverse tunnel name . | ||||
| SsleMplsTpTunnelCfgControlDescription | 1.3.6.1.4.1.6296.101.16.14.1.2.27 | OCTET STRING | RW | |
scalar · OCTET STRING · read-write · current Description. | ||||
| SsleMplsTpTunnelCfgControlHlspSeverTunnelName | 1.3.6.1.4.1.6296.101.16.14.1.2.28 | OCTET STRING | RW | |
scalar · OCTET STRING · read-write · current This object is used to set the server Tunnel name for associating server and client. | ||||
| SsleMplsTpTunnelCfgControlQosPolicyName | 1.3.6.1.4.1.6296.101.16.14.1.2.29 | OCTET STRING | RW | |
scalar · OCTET STRING · read-write · current This object is used to set the Qos Policy name. | ||||