SLE-AM-MIB
DASAN Co.,LTD.This MIB contains all needed informations about Alarm Manager.
snmptranslate -m SLE-AM-MIB -Tpsnmpwalk -v2c -c <community> -m SLE-AM-MIB <host> 1.3.6.1.4.1.6296.101.15Imports
| DASAN-SMI | sleMgmt |
|---|---|
| SLE-TC-MIB | SleControlRequestResultType, SleControlStatusType |
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP |
| SNMPv2-SMI | Bits, Gauge32, Integer32, IpAddress, MODULE-IDENTITY, MibIdentifier, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, iso, zeroDotZero |
| SNMPv2-TC | DisplayString, PhysAddress, TEXTUAL-CONVENTION |
OID tree
| Name | OID | Type | Access | Status |
|---|---|---|---|---|
| IsleAlarmMgr | 1.3.6.1.4.1.6296.101.15 | |||
identity This MIB contains all needed informations about Alarm Manager. | ||||
| SsleAMAlarmTrapNeId | 1.3.6.1.4.1.6296.101.15.1 | OCTET STRING (SIZE (6)) | RO | |
scalar · OCTET STRING (SIZE (6)) · read-only · current use for NE idendification when alarm(or event) trap system MAC address | ||||
| NsleAMConfigBase | 1.3.6.1.4.1.6296.101.15.2 | |||
| TsleAMConfigTable | 1.3.6.1.4.1.6296.101.15.2.1 | NA | ||
table · not-accessible · current This table is the class Master Alarm table. It gets populated when system init is done. And it contains all the class alarms supported for the device | ||||
| RsleAMConfigEntry | 1.3.6.1.4.1.6296.101.15.2.1.1 | NA | ||
row · not-accessible · current | ||||
| CsleAMConfigAlarmClassId | 1.3.6.1.4.1.6296.101.15.2.1.1.1 | AMAlarmClassId | RO | |
column · AMAlarmClassId · read-only · current Class ID starts from 1 to 65535 for the system. And these IDs are defined by alarm-client | ||||
| CsleAMConfigAlarmId | 1.3.6.1.4.1.6296.101.15.2.1.1.2 | AMAlarmId | RO | |
column · AMAlarmId · read-only · current Alarm ID Alarm ID starts from 1 to 65535 for the system. And these IDs are defined by alarm-client | ||||
| CsleAMConfigAlarmName | 1.3.6.1.4.1.6296.101.15.2.1.1.3 | OCTET STRING | RW | |
column · OCTET STRING · read-write · current Alarm Name string | ||||
| CsleAMConfigAlarmSeverity | 1.3.6.1.4.1.6296.101.15.2.1.1.4 | AMAlarmSeverity | RO | |
column · AMAlarmSeverity · read-only · current Alarm severity: The default severity is pre-defined by each Alarm manager clients critical(1), major(2), minor(3), warning(4), intermediate(5), | ||||
| CsleAMConfigAlarmEnableState | 1.3.6.1.4.1.6296.101.15.2.1.1.5 | AMTrapState | RO | |
column · AMTrapState · read-only · current Alarm Trap State. Based on the trap state, the alarm will be notified to NMS. If the TRAP STATE is enabled then the alarm will be notified else wont be notified. enable (1) disabe (0) | ||||
| CsleAMConfigAlarmRaiseGuardTime | 1.3.6.1.4.1.6296.101.15.2.1.1.6 | AMAlarmGuardTime | RO | |
column · AMAlarmGuardTime · read-only · current Alarm raise Soaking time. When any alarm is raised, this attribute specifies how much time the alarm should be soaked before notifying to Alarm manager range:1 ~ 30, (if '0', no soaking time) | ||||
| CsleAMConfigAlarmClearGuardTime | 1.3.6.1.4.1.6296.101.15.2.1.1.7 | AMAlarmGuardTime | RO | |
column · AMAlarmGuardTime · read-only · current Alarm clear Soaking time. When any alarm is cleared, this attribute specifies how much time the alarm should be soaked before notifying to Alarm manager range:1 ~ 30, (if '0', no soaking time) | ||||
| CsleAMConfigAlarmLed | 1.3.6.1.4.1.6296.101.15.2.1.1.8 | INTEGER | RW | |
column · INTEGER · read-write · current Alarm led configuration. Determinde led operate or not, when alarms occur. off(0): led not operate on(1) : led operate
| ||||
| CsleAMConfigSpecificId | 1.3.6.1.4.1.6296.101.15.2.1.1.9 | Integer32 | RW | |
column · Integer32 · read-write · current Alarm Configuration specific ID(4bytes) classId and alarmID are combinded with a specificID * 1st,2nd Bytes - ClassId * 3rd,4th bytes - alarmID | ||||
| NsleAMConfigControl | 1.3.6.1.4.1.6296.101.15.2.2 | |||
| SsleAMConfigControlRequest | 1.3.6.1.4.1.6296.101.15.2.2.1 | INTEGER | RW | |
scalar · INTEGER · read-write · current The configuration commands, and user can configure functions via setting this entry as proper value.
| ||||
| SsleAMConfigControlStatus | 1.3.6.1.4.1.6296.101.15.2.2.2 | SleControlStatusType | RO | |
scalar · SleControlStatusType · read-only · current status of user command. User have to check this value as .busy. or .idle. before do setRequest. | ||||
| SsleAMConfigControlTimer | 1.3.6.1.4.1.6296.101.15.2.2.3 | Gauge32 | RW | |
scalar · Gauge32 · read-write · current the wait-time until setRequest end. In case of short-time command, this value is 0 | ||||
| SsleAMConfigControlTimeStamp | 1.3.6.1.4.1.6296.101.15.2.2.4 | TimeTicks | RO | |
scalar · TimeTicks · read-only · current the time stamp of the last command. (don.t care) | ||||
| SsleAMConfigControlReqResult | 1.3.6.1.4.1.6296.101.15.2.2.5 | SleControlRequestResultType | RO | |
scalar · SleControlRequestResultType · read-only · current Result of the last command. | ||||
| SsleAMConfigControlAlarmClassId | 1.3.6.1.4.1.6296.101.15.2.2.6 | AMAlarmClassId | RW | |
scalar · AMAlarmClassId · read-write · current Alarm Manager Class ID | ||||
| SsleAMConfigControlAlarmId | 1.3.6.1.4.1.6296.101.15.2.2.7 | AMAlarmId | RW | |
scalar · AMAlarmId · read-write · current Alarm Manager Alarm Index | ||||
| SsleAMConfigControlSeverity | 1.3.6.1.4.1.6296.101.15.2.2.8 | AMAlarmSeverity | RW | |
scalar · AMAlarmSeverity · read-write · current Alarm Class Severity critical(1), major(2), minor(3), warning(4), ignore(5), default(6) | ||||
| SsleAMConfigControlEnableState | 1.3.6.1.4.1.6296.101.15.2.2.9 | AMTrapState | RW | |
scalar · AMTrapState · read-write · current Alarm Trap State. Based on the trap state, the alarm will be notified to NMS. If the TRAP STATE is enabled then the alarm will be notified else wont be notified. enable (1) disabe (0) | ||||
| SsleAMConfigControlRaiseGuardTime | 1.3.6.1.4.1.6296.101.15.2.2.10 | AMAlarmGuardTime | RW | |
scalar · AMAlarmGuardTime · read-write · current Alarm Raise Soaking time. When any alarm is raised, this attribute specifies how much time the alarm should be soaked before notifying to Alarm manager range:1 ~ 30, (if '0', no soaking time) | ||||
| SsleAMConfigControlClearGuardTime | 1.3.6.1.4.1.6296.101.15.2.2.11 | AMAlarmGuardTime | RW | |
scalar · AMAlarmGuardTime · read-write · current Alarm clear Soaking time. When any alarm is cleared, this attribute specifies how much time the alarm should be soaked before notifying to Alarm manager range:1 ~ 30, (if '0', no soaking time) | ||||
| SsleAMConfigControlLed | 1.3.6.1.4.1.6296.101.15.2.2.12 | Integer32 | RW | |
scalar · Integer32 · read-write · current Alarm led configuration. Determinde led operate or not, when alarms occur. off(0): led not operate on(1) : led operate | ||||
| NsleAMConfigNotification | 1.3.6.1.4.1.6296.101.15.2.3 | |||
| !sleAMConfigSeverityChanged | 1.3.6.1.4.1.6296.101.15.2.3.1 | |||
notification · current Notification for Alarm severity change | ||||
| !sleAMConfigEnableStateChanged | 1.3.6.1.4.1.6296.101.15.2.3.2 | |||
notification · current Notification for Class Trap State change | ||||
| !sleAMConfigRaiseGuardTimeChanged | 1.3.6.1.4.1.6296.101.15.2.3.3 | |||
notification · current Notification for Raise Soak time change | ||||
| !sleAMConfigClearGuardTimeChanged | 1.3.6.1.4.1.6296.101.15.2.3.4 | |||
notification · current Notification for Clear Soak time change | ||||
| !sleAMConfigLedChanged | 1.3.6.1.4.1.6296.101.15.2.3.5 | |||
notification · current Notification for Alarm led configuration change | ||||
| NsleAMCurrentBase | 1.3.6.1.4.1.6296.101.15.3 | |||
| TsleAMCurrentTable | 1.3.6.1.4.1.6296.101.15.3.1 | NA | ||
table · not-accessible · current This table contains the current active alarms for the Alarm Class. Each Row in this table gets populated when any Alarm is raised | ||||
| RsleAMCurrentEntry | 1.3.6.1.4.1.6296.101.15.3.1.1 | NA | ||
row · not-accessible · current
| ||||
| CsleAMCurrentSeqId | 1.3.6.1.4.1.6296.101.15.3.1.1.1 | Unsigned32 (1..65535) | RO | |
column · Unsigned32 (1..65535) · read-only · current alarm sequence id key of current alarm table it generated by alarm-manager automatically | ||||
| CsleAMCurrentAlarmSource | 1.3.6.1.4.1.6296.101.15.3.1.1.2 | AMAlarmSrc | RO | |
column · AMAlarmSrc · read-only · current alarm location infomation |type|length|value|type|length|value|.... type (1-byte) : alarm location type length(1-byte) : alarm location value length value (length-bytes) : alarm location value | ||||
| CsleAMCurrentAlarmClassId | 1.3.6.1.4.1.6296.101.15.3.1.1.3 | AMAlarmClassId | RO | |
column · AMAlarmClassId · read-only · current Class ID starts from 1 to 65535 for the system. And these IDs are defined by alarm-client | ||||
| CsleAMCurrentAlarmId | 1.3.6.1.4.1.6296.101.15.3.1.1.4 | AMAlarmId | RO | |
column · AMAlarmId · read-only · current Alarm ID Alarm ID starts from 1 to 65535 for the system. And these IDs are defined by alarm-client | ||||
| CsleAMCurrentAlarmStatus | 1.3.6.1.4.1.6296.101.15.3.1.1.5 | AlarmStatus | RO | |
column · AlarmStatus · read-only · current Current Alarm State: raised (1), masked(2) | ||||
| CsleAMCurrentAlarmSeverity | 1.3.6.1.4.1.6296.101.15.3.1.1.6 | AMAlarmSeverity | RO | |
column · AMAlarmSeverity · read-only · current Current Alarm Severity: critical(1), major(2), minor(3), warning(4) | ||||
| CsleAMCurrentAlarmReason | 1.3.6.1.4.1.6296.101.15.3.1.1.7 | AMAlarmReason | RO | |
column · AMAlarmReason · read-only · current reasion string | ||||
| CsleAMCurrentTimeAndDate | 1.3.6.1.4.1.6296.101.15.3.1.1.8 | TimeTicks | RO | |
column · TimeTicks · read-only · current Current Alarm Time and Date | ||||
| CsleAMCurrentSpecificId | 1.3.6.1.4.1.6296.101.15.3.1.1.9 | INTEGER | RW | |
column · INTEGER · read-write · current Current Alarm specific ID(4bytes) classId and alarmID are combinded with a specificID * 1st,2nd Bytes - ClassId * 3rd,4th bytes - alarmID | ||||
| NsleAMCurrentControl | 1.3.6.1.4.1.6296.101.15.3.2 | |||
| SsleAMCurrentControlRequest | 1.3.6.1.4.1.6296.101.15.3.2.1 | INTEGER | RW | |
scalar · INTEGER · read-write · current The configuration commands, and user can configure functions via setting this entry as proper value. 1: all current alarm clear 2: current alarm clear by SeqId 3: current alarm clear by Source(location)
| ||||
| SsleAMCurrentControlStatus | 1.3.6.1.4.1.6296.101.15.3.2.2 | SleControlStatusType | RO | |
scalar · SleControlStatusType · read-only · current status of user command. User have to check this value as .busy. or .idle. before do setRequest. | ||||
| SsleAMCurrentControlTimer | 1.3.6.1.4.1.6296.101.15.3.2.3 | Gauge32 | RW | |
scalar · Gauge32 · read-write · current the wait-time until setRequest end. In case of short-time command, this value is 0 | ||||
| SsleAMCurrentControlTimeStamp | 1.3.6.1.4.1.6296.101.15.3.2.4 | TimeTicks | RO | |
scalar · TimeTicks · read-only · current the time stamp of the last command. (don.t care) | ||||
| SsleAMCurrentControlReqResult | 1.3.6.1.4.1.6296.101.15.3.2.5 | SleControlRequestResultType | RO | |
scalar · SleControlRequestResultType · read-only · current Result of the last command. | ||||
| SsleAMCurrentControlSeqId | 1.3.6.1.4.1.6296.101.15.3.2.6 | Unsigned32 | RW | |
scalar · Unsigned32 · read-write · current current alarmControl Sequence ID.(0, all mcurrent alarm cleared) Valid only if the sleAMHistoryControlRequest value is set to 2(alarmHistoryClearBySeqId). | ||||
| SsleAMCurrentControlSource | 1.3.6.1.4.1.6296.101.15.3.2.7 | AMAlarmSrc | RW | |
scalar · AMAlarmSrc · read-write · current current alarm clear location infomation |type|length|value|type|length|value|.... type (1-byte) : alarm location type length(1-byte) : alarm location value length value (length-bytes) : alarm location value | ||||
| NsleAMCurrentNotification | 1.3.6.1.4.1.6296.101.15.3.3 | |||
| !sleAMCurrentAlarmCleared | 1.3.6.1.4.1.6296.101.15.3.3.1 | |||
notification · current Notification for current alarm clear | ||||
| !sleAlarmTrapAlarm | 1.3.6.1.4.1.6296.101.15.3.3.2 | |||
notification · current Notify Alarm Raise/Clear TRAPS to NMS for each entry in the Table | ||||
| !sleAlarmTrapEvent | 1.3.6.1.4.1.6296.101.15.3.3.3 | |||
notification · current Notify Event Occur TRAPS to NMS for each entry in the Table | ||||
| NsleAMHistoryBase | 1.3.6.1.4.1.6296.101.15.4 | |||
| TsleAMHistoryTable | 1.3.6.1.4.1.6296.101.15.4.1 | NA | ||
table · not-accessible · current This Table is used to for keeping the Alarm History | ||||
| RsleAMHistoryEntry | 1.3.6.1.4.1.6296.101.15.4.1.1 | NA | ||
row · not-accessible · current
| ||||
| CsleAMHistorySeqId | 1.3.6.1.4.1.6296.101.15.4.1.1.1 | Unsigned32 (1..65535) | RO | |
column · Unsigned32 (1..65535) · read-only · current Alarm History Sequence ID. This sequence Id is maintained based on the TRAP sent. | ||||
| CsleAMHistoryAlarmSource | 1.3.6.1.4.1.6296.101.15.4.1.1.2 | AMAlarmSrc | RO | |
column · AMAlarmSrc · read-only · current |type|length|value|type|length|value|.... type (1-byte) : alarm location type length(1-byte) : alarm location value length value (length-bytes) : alarm location value | ||||
| CsleAMHistoryAlarmClassId | 1.3.6.1.4.1.6296.101.15.4.1.1.3 | AMAlarmClassId | RO | |
column · AMAlarmClassId · read-only · current Class ID starts from 1 to 65535 for the system. And these IDs are defined by alarm-client | ||||
| CsleAMHistoryAlarmId | 1.3.6.1.4.1.6296.101.15.4.1.1.4 | AMAlarmId | RO | |
column · AMAlarmId · read-only · current History Alarm ID Alarm ID starts from 1 to 65535 for the system. And these IDs are defined by alarm-client | ||||
| CsleAMHistoryAlarmStatus | 1.3.6.1.4.1.6296.101.15.4.1.1.5 | AlarmStatus | RO | |
column · AlarmStatus · read-only · current History Alarm State: cleared (0), raised (1), masked(2) | ||||
| CsleAMHistoryAlarmSeverity | 1.3.6.1.4.1.6296.101.15.4.1.1.6 | AMAlarmSeverity | RO | |
column · AMAlarmSeverity · read-only · current History alarm Severity critical(1), major(2), minor(3), warning(4) | ||||
| CsleAMHistoryAlarmReason | 1.3.6.1.4.1.6296.101.15.4.1.1.7 | AMAlarmReason | RW | |
column · AMAlarmReason · read-write · current History alarm Reason string | ||||
| CsleAMHistoryAlarmTimeDate | 1.3.6.1.4.1.6296.101.15.4.1.1.8 | TimeTicks | RO | |
column · TimeTicks · read-only · current History Alarm Time and Date | ||||
| CsleAMHistorySpecificId | 1.3.6.1.4.1.6296.101.15.4.1.1.9 | Integer32 | RW | |
column · Integer32 · read-write · current Alarm History specific ID(4bytes) classId and alarmID are combinded with a specificID * 1st,2nd Bytes - ClassId * 3rd,4th bytes - alarmID | ||||
| NsleAMHistoryControl | 1.3.6.1.4.1.6296.101.15.4.2 | |||
| SsleAMHistoryControlRequest | 1.3.6.1.4.1.6296.101.15.4.2.1 | INTEGER | RW | |
scalar · INTEGER · read-write · current The configuration commands, and user can configure functions via setting this entry as proper value. clearAlarmHistory : clears the alarms from the History Table 1: all alarm history clear 2: alarm history clear by SeqId 3: alarm history clear by Source(location)
| ||||
| SsleAMHistoryControlStatus | 1.3.6.1.4.1.6296.101.15.4.2.2 | SleControlStatusType | RO | |
scalar · SleControlStatusType · read-only · current status of user command. User have to check this value as .busy. or .idle. before do setRequest. | ||||
| SsleAMHistoryControlTimer | 1.3.6.1.4.1.6296.101.15.4.2.3 | Gauge32 | RW | |
scalar · Gauge32 · read-write · current the wait-time until setRequest end. In case of short-time command, this value is 0 | ||||
| SsleAMHistoryControlTimeStamp | 1.3.6.1.4.1.6296.101.15.4.2.4 | TimeTicks | RO | |
scalar · TimeTicks · read-only · current the time stamp of the last command. (don.t care) | ||||
| SsleAMHistoryControlReqResult | 1.3.6.1.4.1.6296.101.15.4.2.5 | SleControlRequestResultType | RO | |
scalar · SleControlRequestResultType · read-only · current Result of the last command. | ||||
| SsleAMHistoryControSeqId | 1.3.6.1.4.1.6296.101.15.4.2.6 | Unsigned32 | RW | |
scalar · Unsigned32 · read-write · current Alarm History Control Sequence ID. Specify cleared history alarm ID (0, all alarm history cleared) | ||||
| SsleAMHistoryControSource | 1.3.6.1.4.1.6296.101.15.4.2.7 | AMAlarmSrc | RW | |
scalar · AMAlarmSrc · read-write · current alarm history clear location infomation Valid only if the sleAMHistoryControlRequest value is set to 3(alarmHistoryClearBySource). |type|length|value|type|length|value|.... type (1-byte) : alarm location type length(1-byte) : alarm location value length value (length-bytes) : alarm location value | ||||
| NsleAMHistoryNotification | 1.3.6.1.4.1.6296.101.15.4.3 | |||
| !sleAMHistoryAlarmCleared | 1.3.6.1.4.1.6296.101.15.4.3.1 | |||
notification · current Notification for History Class cleared | ||||
| NsleAMAcoBase | 1.3.6.1.4.1.6296.101.15.5 | |||
| NsleAMAcoInfoEntry | 1.3.6.1.4.1.6296.101.15.5.1 | |||
| SsleAMAcoInfo | 1.3.6.1.4.1.6296.101.15.5.1.1 | AMAlarmAco | RO | |
scalar · AMAlarmAco · read-only · current ACO control configuration acoOff(1) : buzzer operation enable. acoOn(2) : buzzer operation disable. acoOpr(3) : current buzzer cut. | ||||
| NsleAMAcoControl | 1.3.6.1.4.1.6296.101.15.5.2 | |||
| SsleAMAcoControlRequest | 1.3.6.1.4.1.6296.101.15.5.2.1 | INTEGER | RW | |
scalar · INTEGER · read-write · current The configuration commands, and user can configure functions via setting this entry as proper value.
| ||||
| SsleAMAcogControlStatus | 1.3.6.1.4.1.6296.101.15.5.2.2 | SleControlStatusType | RO | |
scalar · SleControlStatusType · read-only · current status of user command. User have to check this value as .busy. or .idle. before do setRequest. | ||||
| SsleAMAcoControlTimer | 1.3.6.1.4.1.6296.101.15.5.2.3 | Gauge32 | RW | |
scalar · Gauge32 · read-write · current the wait-time until setRequest end. In case of short-time command, this value is 0 | ||||
| SsleAMAcoControlTimeStamp | 1.3.6.1.4.1.6296.101.15.5.2.4 | TimeTicks | RO | |
scalar · TimeTicks · read-only · current the time stamp of the last command. (don.t care) | ||||
| SsleAMAcoControlReqResult | 1.3.6.1.4.1.6296.101.15.5.2.5 | SleControlRequestResultType | RO | |
scalar · SleControlRequestResultType · read-only · current Result of the last command. | ||||
| SsleAMAcoControlSet | 1.3.6.1.4.1.6296.101.15.5.2.6 | AMAlarmAco | RW | |
scalar · AMAlarmAco · read-write · current ACO control acoOff(1) : buzzer operation enable. acoOn(2) : buzzer operation disable. acoOpr(3) : current buzzer cut. | ||||
| NsleAMAcoNotification | 1.3.6.1.4.1.6296.101.15.5.3 | |||
| !sleAMAcoChanged | 1.3.6.1.4.1.6296.101.15.5.3.1 | |||
notification · current Notification for Alarm ACO configuration change | ||||
| NsleAMLedBase | 1.3.6.1.4.1.6296.101.15.6 | |||
| TsleAMLedTable | 1.3.6.1.4.1.6296.101.15.6.1 | NA | ||
table · not-accessible · current This table contains the LED status and configuration. | ||||
| RsleAMLedEntry | 1.3.6.1.4.1.6296.101.15.6.1.1 | NA | ||
row · not-accessible · current
| ||||
| CsleAMLedSeverity | 1.3.6.1.4.1.6296.101.15.6.1.1.1 | INTEGER | RW | |
column · INTEGER · read-write · current LED Alarm Severity critical(1), major(2), minor(3),
| ||||
| CsleAMLedSet | 1.3.6.1.4.1.6296.101.15.6.1.1.2 | AMAlarmLed | RW | |
column · AMAlarmLed · read-write · current ACO control configuration acoOff(1) : buzzer operation enable. acoOn(2) : buzzer operation disable. acoOpr(3) : current buzzer cut. | ||||
| CsleAMLedCount | 1.3.6.1.4.1.6296.101.15.6.1.1.3 | Integer32 | RW | |
column · Integer32 · read-write · current alarm count of the associated led | ||||
| NsleAMLedControl | 1.3.6.1.4.1.6296.101.15.6.2 | |||
| SsleAMLedControlRequest | 1.3.6.1.4.1.6296.101.15.6.2.1 | INTEGER | RW | |
scalar · INTEGER · read-write · current The configuration commands, and user can configure functions via setting this entry as proper value.
| ||||
| SsleAMLedControlStatus | 1.3.6.1.4.1.6296.101.15.6.2.2 | SleControlStatusType | RO | |
scalar · SleControlStatusType · read-only · current status of user command. User have to check this value as .busy. or .idle. before do setRequest. | ||||
| SsleAMLedControlTimer | 1.3.6.1.4.1.6296.101.15.6.2.3 | Gauge32 | RW | |
scalar · Gauge32 · read-write · current the wait-time until setRequest end. In case of short-time command, this value is 0 | ||||
| SsleAMLedControlTimeStamp | 1.3.6.1.4.1.6296.101.15.6.2.4 | TimeTicks | RO | |
scalar · TimeTicks · read-only · current the time stamp of the last command. (don.t care) | ||||
| SsleAMLedControlReqResult | 1.3.6.1.4.1.6296.101.15.6.2.5 | SleControlRequestResultType | RO | |
scalar · SleControlRequestResultType · read-only · current Result of the last command. | ||||
| SsleAMLedControlSeverity | 1.3.6.1.4.1.6296.101.15.6.2.6 | INTEGER | RW | |
scalar · INTEGER · read-write · current LED Alarm Severity critical(1), major(2), minor(3),
| ||||
| SsleAMLedControlSet | 1.3.6.1.4.1.6296.101.15.6.2.7 | AMAlarmLed | RW | |
scalar · AMAlarmLed · read-write · current LED control configuration ledOff(1) : LED operation disable. ledOn(2) : LED operation enable. ledOpr(3) : current LED off. | ||||
| NsleAMLedNotification | 1.3.6.1.4.1.6296.101.15.6.3 | |||
| !sleAMLedChanged | 1.3.6.1.4.1.6296.101.15.6.3.1 | |||
notification · current Notification for LED configuration change | ||||
Textual conventions
AMAlarmAcoINTEGERacoOff(1)acoOn(2)acoOpr(3)ACO control configuration acoOff(1) : buzzer operation enable. acoOn(2) : buzzer operation disable. acoOpr(3) : current buzzer cut.
AMAlarmClassIdINTEGER (1..65535)alarm class id 1~65535
AMAlarmGuardTimeINTEGER (0..30)alarm guard time 1~30 (second) 0, no alarm guard time apply
AMAlarmIdINTEGER (1..65535)Current Alarm ID 1~65535
AMAlarmLedINTEGERoprLed(3)setLedOff(1)setLedOn(2)LED control configuration ledOff(1) : LED operation disable. ledOn(2) : LED operation enable. ledOpr(3) : current LED off.
AMAlarmReasonOCTET STRING (SIZE (0..256))Alarm reason Description string (include location infomatiln)
AMAlarmSeverityINTEGERcritical(1)default(6)intermediate(5)major(2)minor(3)warning(4)Severity of Alarm
AMAlarmSrcOCTET STRING (SIZE (68))|type|length|value|type|length|value|.... type (1-byte) : alarm location type length(1-byte) : alarm location value length value (length-bytes) : alarm location value
AMDateTimeUnsigned32TOD integer value
AMTrapStateINTEGERdisable(0)enable(1)This status explains whether TRAP status is enabled or disabled. Enable(1) : Alarm Trap State is Enabled. Hence TRAPs will be sent for this. Disable(0) : Alarm Trap State is Disabled. So Alarms won't be notified to user.
AlarmStatusINTEGERcleared(0)disabled(3)event(5)forcedClear(4)masked(2)raised(1)unmasked(6)This is the status of the alarm. Cleared(0) : Alarm status is cleared Raised(1) : Alarm status is raised. Masked(2) : alarm is suppressed. Disable(3) : Alarm disable Forced-clear(4) : Init alarm Event(5) : Event report Unmasked(6) :Alarm suppression release
Traps / Notifications
- sleAMAcoChanged
1.3.6.1.4.1.6296.101.15.5.3.1 - sleAMConfigClearGuardTimeChanged
1.3.6.1.4.1.6296.101.15.2.3.4 - sleAMConfigEnableStateChanged
1.3.6.1.4.1.6296.101.15.2.3.2 - sleAMConfigLedChanged
1.3.6.1.4.1.6296.101.15.2.3.5 - sleAMConfigRaiseGuardTimeChanged
1.3.6.1.4.1.6296.101.15.2.3.3 - sleAMConfigSeverityChanged
1.3.6.1.4.1.6296.101.15.2.3.1 - sleAMCurrentAlarmCleared
1.3.6.1.4.1.6296.101.15.3.3.1 - sleAMHistoryAlarmCleared
1.3.6.1.4.1.6296.101.15.4.3.1 - sleAMLedChanged
1.3.6.1.4.1.6296.101.15.6.3.1 - sleAlarmTrapAlarm
1.3.6.1.4.1.6296.101.15.3.3.2 - sleAlarmTrapEvent
1.3.6.1.4.1.6296.101.15.3.3.3