HH3C-DOT11-CFG-MIB
H3CThis MIB provides information about WLAN configuration. GLOSSARY IEEE 802.11 Standard to encourage interoperability among wireless networking equipment. Access point (AP) Transmitter/receiver (transceiver) device that commonly connects and transports data between a wireless network and a wired network. Access control (AC) To control and manage multi-APs, it will bridge wireless and wired network. Fat AP Applied in the home, SOHO and so on, and it could work independently without help from AC. Fit AP Applied in the enterprise environment, it will work under the control and management from AC. Control And Provisioning of Wireless Access Points Protocol The short name of protocol is CAPWAP. AC will control and manage AP by CAPWAP tunnel protocol defined by IETF. Also, a data tunnel will be set up between AC and AP. BSS IEEE 802.11 Basic Service Set (Radio Cell). The BSS of an AP comprises of the stations directly associating with the AP. Radio The chip set to receive and send wireless signal. Association The service used to establish access point or station mapping and enable station invocation of the distribution system services. (Wireless clients attempt to connect to access points.) Basic Rate A data rate that is mandatory for client devices to support in order for them to achieve successful association. MSDU MAC Service Data Unit, it is frame format defined by 802.11. TU It is 1,024 microseconds (ms), which is about 1 millisecond. AKM The authentication and key management method defined by 802.11i, and which includes 802.1x and pre-shared key.
snmptranslate -m HH3C-DOT11-CFG-MIB -Tpsnmpwalk -v2c -c <community> -m HH3C-DOT11-CFG-MIB <host> 1.3.6.1.4.1.25506.2.75.4Imports
| HH3C-DOT11-REF-MIB | Hh3cDot11AuthenType, Hh3cDot11ChannelScopeType, Hh3cDot11CirMode, Hh3cDot11ObjectIDType, Hh3cDot11PreambleType, Hh3cDot11RadioElementIndex, Hh3cDot11RadioScopeType, Hh3cDot11RadioType, Hh3cDot11RadioType2, Hh3cDot11SSIDEncryptModeType, Hh3cDot11SSIDStringType, Hh3cDot11SecIEStatusType, Hh3cDot11ServicePolicyIDType, Hh3cDot11TruthValueCM, Hh3cDot11TunnelSecSchemType, Hh3cDot11TxPwrLevelScopeType, Hh3cDot11WorkMode, hh3cDot11, hh3cDot11APElementIndex |
|---|---|
| IF-MIB | ifIndex |
| INET-ADDRESS-MIB | InetAddress |
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP |
| SNMPv2-SMI | Bits, Integer32, IpAddress, MODULE-IDENTITY, MibIdentifier, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, iso |
| SNMPv2-TC | DateAndTime, DisplayString, MacAddress, PhysAddress, RowStatus, TEXTUAL-CONVENTION, TruthValue |
OID tree
| Name | OID | Type | Access | Status |
|---|---|---|---|---|
| Ihh3cDot11CFG | 1.3.6.1.4.1.25506.2.75.4 | |||
identity This MIB provides information about WLAN configuration. GLOSSARY IEEE 802.11 Standard to encourage interoperability among wireless networking equipment. Access point (AP) Transmitter/receiver (transceiver) device that commonly connects and transports data between a wireless network and a wired network. Access control (AC) To control and manage multi-APs, it will bridge wireless and wired network. Fat AP Applied in the home, SOHO and so on, and it could work independently without help from AC. Fit AP Applied in the enterprise environment, it will work under the control and management from AC. Control And Provisioning of Wireless Access Points Protocol The short name of protocol is CAPWAP. AC will control and manage AP by CAPWAP tunnel protocol defined by IETF. Also, a data tunnel will be set up between AC and AP. BSS IEEE 802.11 Basic Service Set (Radio Cell). The BSS of an AP comprises of the stations directly associating with the AP. Radio The chip set to receive and send wireless signal. Association The service used to establish access point or station mapping and enable station invocation of the distribution system services. (Wireless clients attempt to connect to access points.) Basic Rate A data rate that is mandatory for client devices to support in order for them to achieve successful association. MSDU MAC Service Data Unit, it is frame format defined by 802.11. TU It is 1,024 microseconds (ms), which is about 1 millisecond. AKM The authentication and key management method defined by 802.11i, and which includes 802.1x and pre-shared key. | ||||
| Nhh3cDot11GlobeConfigGroup | 1.3.6.1.4.1.25506.2.75.4.1 | |||
| Shh3cDot11GlobalCountryCode | 1.3.6.1.4.1.25506.2.75.4.1.1 | OCTET STRING (SIZE (3)) | RW | |
scalar · OCTET STRING (SIZE (3)) · read-write · current Represents the country code for wireless network. | ||||
| Shh3cDot11StaKeepALiveTimerIntvl | 1.3.6.1.4.1.25506.2.75.4.1.2 | Unsigned32 | RW | |
scalar · Unsigned32 · read-write · current Represents the interval of the keep alive requests sent between AP and STA. Default value 0 : The keep alive function is disabled.
| ||||
| Shh3cDot11StaIdleTimerIntvl | 1.3.6.1.4.1.25506.2.75.4.1.3 | Integer32 | RW | |
scalar · Integer32 · read-write · current Represents the interval for which the link between AP and STA ( power-save or awake ) can be idle.
| ||||
| Shh3cDot11BroadcastProbeReply | 1.3.6.1.4.1.25506.2.75.4.1.4 | TruthValue | RW | |
scalar · TruthValue · read-write · current Represents enable the AP to reply broadcast probe or not. 'true' : The AP to reply broadcast probe is enabled. 'false': The AP to reply broadcast probe is disabled | ||||
| Shh3cDot11APScanMode | 1.3.6.1.4.1.25506.2.75.4.1.5 | INTEGER | RW | |
scalar · INTEGER · read-write · current Represents the scanning mode for AP. The following values are supported: active - AP will actively do scan. passive - AP will passively do scan.
| ||||
| Shh3cDot11ACCtrlTunnelSecSupport | 1.3.6.1.4.1.25506.2.75.4.1.6 | Hh3cDot11TunnelSecSchemType | RW | |
scalar · Hh3cDot11TunnelSecSchemType · read-write · current Represents what security schemes are supported for CAPWAP Control tunnel. | ||||
| Shh3cDot11ACDataTunnelSecSupport | 1.3.6.1.4.1.25506.2.75.4.1.7 | Hh3cDot11TunnelSecSchemType | RW | |
scalar · Hh3cDot11TunnelSecSchemType · read-write · current Represents what security schemes are supported for CAPWAP data tunnel. The cleartxt is the default scheme. | ||||
| Shh3cDot11ACAutoAPSupport | 1.3.6.1.4.1.25506.2.75.4.1.8 | TruthValue | RW | |
scalar · TruthValue · read-write · current Represents enable the auto AP functionality or not. 'true' : The auto AP functionality is enabled. 'false': The auto AP functionality is disabled | ||||
| Shh3cDot11AutoAPName | 1.3.6.1.4.1.25506.2.75.4.1.9 | OCTET STRING (SIZE (0..127)) | RW | |
scalar · OCTET STRING (SIZE (0..127)) · read-write · current Represents the name of auto AP that needs to be made persistent. When read the value from the node, NULL value be returned. | ||||
| Shh3cDot11PersistentName | 1.3.6.1.4.1.25506.2.75.4.1.10 | OCTET STRING (SIZE (0..127)) | RW | |
scalar · OCTET STRING (SIZE (0..127)) · read-write · current Represents the new name of auto AP after being made persistent. When read the value from the node, NULL value be returned. | ||||
| Shh3cDot11IntfTrapThreshold | 1.3.6.1.4.1.25506.2.75.4.1.11 | Integer32 | RW | |
scalar · Integer32 · read-write · current Represents threshold of interference trap. If signal strength of the device exceeds this threshold, corresponding trap will be sent.
| ||||
| Shh3cDot11MonitorInterval | 1.3.6.1.4.1.25506.2.75.4.1.12 | Unsigned32 (0 | 5..15) | RW | |
scalar · Unsigned32 (0 | 5..15) · read-write · current Represents the monitoring interval. Default value 0 : The monitoring functionality is changed to real-time mode.
| ||||
| Shh3cDot11SampleInterval | 1.3.6.1.4.1.25506.2.75.4.1.13 | Unsigned32 (0 | 10..300) | RW | |
scalar · Unsigned32 (0 | 10..300) · read-write · current Represents the sampling interval. Default value 0 : The sampling functionality is disabled.
| ||||
| Shh3cDot11ChnlSwitChkInterval | 1.3.6.1.4.1.25506.2.75.4.1.14 | Unsigned32 (8..180) | RW | |
scalar · Unsigned32 (8..180) · read-write · current Represents the checking interval of channel switch.
| ||||
| Shh3cDot11APUserUplimit | 1.3.6.1.4.1.25506.2.75.4.1.15 | Unsigned32 (0..65535) | RW | |
scalar · Unsigned32 (0..65535) · read-write · current Represents the upper limit of user which has access to this AP. | ||||
| Shh3cDot11APL2IsolateEnable | 1.3.6.1.4.1.25506.2.75.4.1.16 | TruthValue | RW | |
scalar · TruthValue · read-write · current Represents enable the layer2 isolation or not. 'true' : The layer2 isolation functionality is enabled. 'false': The layer2 isolation functionality is disabled. | ||||
| Shh3cDot11APBSSIDSupportNum | 1.3.6.1.4.1.25506.2.75.4.1.17 | Integer32 | RO | |
scalar · Integer32 · read-only · current Represents the max number of BSSID supported by Current AP. | ||||
| Shh3cDot11APLastUpdateStatTime | 1.3.6.1.4.1.25506.2.75.4.1.18 | DateAndTime | RO | |
scalar · DateAndTime · read-only · current Represents date and time update statistic information lately. | ||||
| Shh3cDot11APDoSProtectEnable | 1.3.6.1.4.1.25506.2.75.4.1.19 | TruthValue | RW | |
scalar · TruthValue · read-write · current Represents enable the DOS protection or not. 'true' : The DOS protection functionality is enabled. 'false': The DOS protection functionality is disabled. | ||||
| Shh3cDot11MaxAPPerIf | 1.3.6.1.4.1.25506.2.75.4.1.20 | Unsigned32 (0..65535) | RW | |
scalar · Unsigned32 (0..65535) · read-write · current Represents max AP number that can be connected to AC interface. | ||||
| Shh3cDot11SampleTimeStamp | 1.3.6.1.4.1.25506.2.75.4.1.21 | DateAndTime | RO | |
scalar · DateAndTime · read-only · current Represents the start time of current sample period. | ||||
| Shh3cDot11UplinkTrackId | 1.3.6.1.4.1.25506.2.75.4.1.22 | Unsigned32 | RW | |
scalar · Unsigned32 · read-write · current Represents the track id of AP. Default value 0 : The uplink track function for AP is disabled. | ||||
| Shh3cDot11RtCollectSwitch | 1.3.6.1.4.1.25506.2.75.4.1.23 | TruthValue | RW | |
scalar · TruthValue · read-write · current This object is used to turn on/off real-time statistics collection between AC and AP. If the value is true, hh3cDot11RtCollectIntvl will take effect. Otherwise, hh3cDot11RglCollectIntvl will take effect. | ||||
| Shh3cDot11RglCollectIntvl | 1.3.6.1.4.1.25506.2.75.4.1.24 | Integer32 | RW | |
scalar · Integer32 · read-write · current This object represents interval to regularly collect statistics from AC to AP.
| ||||
| Shh3cDot11RtCollectIntvl | 1.3.6.1.4.1.25506.2.75.4.1.25 | Integer32 | RW | |
scalar · Integer32 · read-write · current This object represents interval to collect real-time statistics from AC to AP.
| ||||
| Shh3cDot11AllAPCpuUsageThreshold | 1.3.6.1.4.1.25506.2.75.4.1.26 | Integer32 (0..100) | RW | |
scalar · Integer32 (0..100) · read-write · current The CPU usage threshold for all AP.
| ||||
| Shh3cDot11AllAPMemUsageThreshold | 1.3.6.1.4.1.25506.2.75.4.1.27 | Integer32 (0..100) | RW | |
scalar · Integer32 (0..100) · read-write · current The memory usage threshold for all AP.
| ||||
| Shh3cDot11AdjIntfTrapThreshold | 1.3.6.1.4.1.25506.2.75.4.1.28 | Integer32 | RW | |
scalar · Integer32 · read-write · current Represents threshold of adjacent interference trap. If signal strength of the device exceeds this threshold, corresponding trap will be sent.
| ||||
| Shh3cDot11AllAPMonitorMode | 1.3.6.1.4.1.25506.2.75.4.1.29 | INTEGER | RW | |
scalar · INTEGER · read-write · current Represents what work mode for All AP. The following values are supported: normal, - AP will supply WLAN service. monitor - AP will be a monitor to find attack. hybrid - AP will supply WLAN service and Device detection is enabled.
| ||||
| Shh3cDot11GlobalApFmwUpdState | 1.3.6.1.4.1.25506.2.75.4.1.30 | INTEGER | RW | |
scalar · INTEGER · read-write · current Represents the status of version auto-update for an AP. The following values are supported: enable - AP version will be updated automatically. disable - AP version will not be updated automatically.
| ||||
| Shh3cDot11ACNasIDCM | 1.3.6.1.4.1.25506.2.75.4.1.31 | OCTET STRING | RW | |
scalar · OCTET STRING · read-write · current Represents the NAS-ID of current AC. | ||||
| Shh3cDot11ACRole | 1.3.6.1.4.1.25506.2.75.4.1.32 | INTEGER | RO | |
scalar · INTEGER · read-only · current Current network status of AC.
The following values are supported:
normal, - normal ac.
central - A central AC is an AC where local ACs are
configured, and it establishes CAPWAP tunnels
with the local ACs.
local - Local ACs provide network access to APs
and process client traffic. They are managed
by the central AC.
| ||||
| Shh3cDot11GlobalLocalACState | 1.3.6.1.4.1.25506.2.75.4.1.33 | INTEGER | RW | |
scalar · INTEGER · read-write · current Represents the status of local-ac for an AC. The following values are supported: enable - LocalAC state will be enabled. disable - LocalAC state will not be enabled.
| ||||
| Shh3cDot11CentralACIPAddress | 1.3.6.1.4.1.25506.2.75.4.1.34 | IpAddress | RW | |
scalar · IpAddress · read-write · current Represents the CentralAC IP address of LocalAC. | ||||
| Shh3cDot11CentralACIPv6Address | 1.3.6.1.4.1.25506.2.75.4.1.35 | OCTET STRING | RW | |
scalar · OCTET STRING · read-write · current Represents the CentralAC IPv6 address of LocalAC. | ||||
| Shh3cDot11iMcIP | 1.3.6.1.4.1.25506.2.75.4.1.36 | IpAddress | RW | |
scalar · IpAddress · read-write · current Represents the iMc IP address. | ||||
| Shh3cDot11iMcPort | 1.3.6.1.4.1.25506.2.75.4.1.37 | Integer32 | RW | |
scalar · Integer32 · read-write · current Represents the iMc Port. | ||||
| Shh3cDot11APProvisionSave | 1.3.6.1.4.1.25506.2.75.4.1.38 | OCTET STRING (SIZE (0..127)) | RW | |
scalar · OCTET STRING (SIZE (0..127)) · read-write · current Sends the provisioned configuration to APs. When you read from this node, the system returns NULL. | ||||
| Shh3cDot11ApRenameCurrentName | 1.3.6.1.4.1.25506.2.75.4.1.39 | OCTET STRING (SIZE (0..127)) | RW | |
scalar · OCTET STRING (SIZE (0..127)) · read-write · current Represents the current name of the AP that needs to be changed. When you read from the node, the system returns NULL. | ||||
| Shh3cDot11ApRenameNewName | 1.3.6.1.4.1.25506.2.75.4.1.40 | OCTET STRING (SIZE (0..127)) | RW | |
scalar · OCTET STRING (SIZE (0..127)) · read-write · current Represents the new name of the AP. When you read from the node, the system returns NULL. | ||||
| Shh3cDot11ACDescription | 1.3.6.1.4.1.25506.2.75.4.1.41 | OCTET STRING | RW | |
scalar · OCTET STRING · read-write · current This attribute will give more information about AC. Administrator could suggest the location, owner or other information for each AC. If the value is set to NULL, the description will be removed. | ||||
| Nhh3cDot11PolicyConfigGroup | 1.3.6.1.4.1.25506.2.75.4.2 | |||
| Thh3cDot11RadioPolicyTable | 1.3.6.1.4.1.25506.2.75.4.2.1 | NA | ||
table · not-accessible · current The table defines the parameters for radio policy, as per radio policy of CLI. One radio policy could be assigned to the different radios (AP). | ||||
| Rhh3cDot11RadioPolicyEntry | 1.3.6.1.4.1.25506.2.75.4.2.1.1 | NA | ||
row · not-accessible · current Each entry contains information of each radio policy. | ||||
| Chh3cDot11RadioPolicyName | 1.3.6.1.4.1.25506.2.75.4.2.1.1.1 | OCTET STRING (SIZE (0..127)) | NA | |
column · OCTET STRING (SIZE (0..127)) · not-accessible · current Represents the name of radio policy. | ||||
| Chh3cDot11BeaconInterval | 1.3.6.1.4.1.25506.2.75.4.2.1.1.2 | Integer32 | RC | |
column · Integer32 · read-create · current Represents the interval for Beacon management frame.
| ||||
| Chh3cDot11DtimInterval | 1.3.6.1.4.1.25506.2.75.4.2.1.1.3 | Integer32 | RC | |
column · Integer32 · read-create · current Represents the number of beacon intervals that shall elapse between transmission of Beacons frames containing a Traffic Indication Map (TIM) element whose DTIM Count field is 0. This value is transmitted in the Delivery TIM (DTIM) Period field of Beacon frames. | ||||
| Chh3cDot11RtsThreshold | 1.3.6.1.4.1.25506.2.75.4.2.1.1.4 | Integer32 | RC | |
column · Integer32 · read-create · current Represents the current minimum size, in octets, of the MAC protocol data unit (MPDU), below which a Request to send/Clear to send (RTS/CTS) handshake shall not be performed.
| ||||
| Chh3cDot11FragThreshold | 1.3.6.1.4.1.25506.2.75.4.2.1.1.5 | Integer32 | RC | |
column · Integer32 · read-create · current Represents the current maximum size, in octets, of the MPDU that may be delivered to the PHY. A MSDU shall be broken into fragments if its size exceeds the value of this attribute after adding MAC headers and trailers.
| ||||
| Chh3cDot11ShortRetryThreshold | 1.3.6.1.4.1.25506.2.75.4.2.1.1.6 | Integer32 | RC | |
column · Integer32 · read-create · current Represents the maximum number of transmission attempts of a frame, the length of which is less than or equal to hh3cDot11RTSThreshold, which shall be made before a failure condition is indicated. | ||||
| Chh3cDot11LongRetryThreshold | 1.3.6.1.4.1.25506.2.75.4.2.1.1.7 | Integer32 | RC | |
column · Integer32 · read-create · current Represents the maximum number of transmission attempts of a frame, the length of which is longer than hh3cDot11RTSThreshold, that shall be made before a failure condition is indicated. | ||||
| Chh3cDot11MaxRxLifetime | 1.3.6.1.4.1.25506.2.75.4.2.1.1.8 | Unsigned32 | RC | |
column · Unsigned32 · read-create · current Represents the elapsed time. After the time specified by hh3cDot11MaxRxLifetime, the further attempts to reassemble the MSDU shall be terminated.
| ||||
| Chh3cDot11RdoPolicyRowStatus | 1.3.6.1.4.1.25506.2.75.4.2.1.1.9 | RowStatus | RC | |
column · RowStatus · read-create · current The status of this table entry. | ||||
| Chh3cDot11RdoClientMaxCount | 1.3.6.1.4.1.25506.2.75.4.2.1.1.10 | Integer32 (0..2147483647) | RC | |
column · Integer32 (0..2147483647) · read-create · current Represent the maximum number of stations supported by this radio policy. | ||||
| Chh3cDot11BeaconIntervalMs | 1.3.6.1.4.1.25506.2.75.4.2.1.1.11 | Integer32 | RC | |
column · Integer32 · read-create · current Represents the interval for Beacon management frame.
| ||||
| Thh3cDot11ServicePolicyTable | 1.3.6.1.4.1.25506.2.75.4.2.2 | NA | ||
table · not-accessible · current The table defines the parameters for ESS, as per service policy of CLI. One service policy could be assigned to the different radios (AP). | ||||
| Rhh3cDot11ServicePolicyEntry | 1.3.6.1.4.1.25506.2.75.4.2.2.1 | NA | ||
row · not-accessible · current Each entry contains information of each service policy. | ||||
| Chh3cDot11ServicePolicyID | 1.3.6.1.4.1.25506.2.75.4.2.2.1.1 | Hh3cDot11ServicePolicyIDType | NA | |
column · Hh3cDot11ServicePolicyIDType · not-accessible · current Represents the ID of each service policy. | ||||
| Chh3cDot11SSIDName | 1.3.6.1.4.1.25506.2.75.4.2.2.1.2 | Hh3cDot11SSIDStringType | RC | |
column · Hh3cDot11SSIDStringType · read-create · current Represents the ESS. As per CLI, the value of service policy name will be SSID. | ||||
| Chh3cDot11SSIDHidden | 1.3.6.1.4.1.25506.2.75.4.2.2.1.3 | TruthValue | RC | |
column · TruthValue · read-create · current This attribute controls whether the SSID will be advertised in the beacon frame. If it is true, then SSID will not be advertised in the beacon frame. | ||||
| Chh3cDot11AuthenMode | 1.3.6.1.4.1.25506.2.75.4.2.2.1.4 | Hh3cDot11AuthenType | RC | |
column · Hh3cDot11AuthenType · read-create · current Represents the Authentication mode defined by 802.11. | ||||
| Chh3cDot11SSIDEncryptionMode | 1.3.6.1.4.1.25506.2.75.4.2.2.1.5 | Hh3cDot11SSIDEncryptModeType | RC | |
column · Hh3cDot11SSIDEncryptModeType · read-create · current Represents the encryption mode for this ESS. | ||||
| Chh3cDot11WlanInfBindingType | 1.3.6.1.4.1.25506.2.75.4.2.2.1.6 | OCTET STRING | RC | |
column · OCTET STRING · read-create · current Represents the service policy will bind to what kind of data forwarding interface. | ||||
| Chh3cDot11WlanInfBindingID | 1.3.6.1.4.1.25506.2.75.4.2.2.1.7 | Integer32 | RC | |
column · Integer32 · read-create · current Represents the interface ID of the interface that ESS will bind to. If the value is set to -1, the binding will be removed. | ||||
| Chh3cDot11SrvPolicyRowStatus | 1.3.6.1.4.1.25506.2.75.4.2.2.1.8 | RowStatus | RC | |
column · RowStatus · read-create · current The status of this table entry. | ||||
| Chh3cDot11ClientMaxCount | 1.3.6.1.4.1.25506.2.75.4.2.2.1.9 | Integer32 (0..2147483647) | RC | |
column · Integer32 (0..2147483647) · read-create · current Represent the maximum number of stations supported by this service policy. | ||||
| Chh3cDot11SPInCirMode | 1.3.6.1.4.1.25506.2.75.4.2.2.1.10 | Hh3cDot11CirMode | RC | |
column · Hh3cDot11CirMode · read-create · current CIR(committed information rate) mode of inbound direction. This object is useful only when the corresponding CIR is nonzero. If value of this object is changed, corresponding CIR will be reset. | ||||
| Chh3cDot11SPInCirValue | 1.3.6.1.4.1.25506.2.75.4.2.2.1.11 | Integer32 | RC | |
column · Integer32 · read-create · current Represents the CIR of inbound direction of this service policy. If the value is 0, it means that no flow control is applied to the service policy, and the corresponding CIR mode is meaningless.
| ||||
| Chh3cDot11SPOutCirMode | 1.3.6.1.4.1.25506.2.75.4.2.2.1.12 | Hh3cDot11CirMode | RC | |
column · Hh3cDot11CirMode · read-create · current CIR(committed information rate) mode of outbound direction. This object is useful only when the corresponding CIR is nonzero. If value of this object is changed, corresponding CIR will be reset. | ||||
| Chh3cDot11SPOutCirValue | 1.3.6.1.4.1.25506.2.75.4.2.2.1.13 | Integer32 | RC | |
column · Integer32 · read-create · current Represents the CIR of outbound direction of this service policy. If the value is 0, it means that no flow control is applied to the service policy, and the corresponding CIR mode is meaningless.
| ||||
| Chh3cDot11WlanInfPVID | 1.3.6.1.4.1.25506.2.75.4.2.2.1.14 | Integer32 | RC | |
column · Integer32 · read-create · current Represents the VLAN ID of SSID. | ||||
| Chh3cDot11SPInCirStaticValue | 1.3.6.1.4.1.25506.2.75.4.2.2.1.15 | Integer32 | RC | |
column · Integer32 · read-create · current Represents the CIR of inbound direction for static CIR mode.
| ||||
| Chh3cDot11SPOutCirStaticValue | 1.3.6.1.4.1.25506.2.75.4.2.2.1.16 | Integer32 | RC | |
column · Integer32 · read-create · current Represents the CIR of outbound direction for static CIR mode.
| ||||
| Chh3cDot11SPIsolate | 1.3.6.1.4.1.25506.2.75.4.2.2.1.17 | TruthValue | RC | |
column · TruthValue · read-create · current If it is true, then stations connected with the service policy are isolated. | ||||
| Chh3cDot11WlanexAuthServerIP | 1.3.6.1.4.1.25506.2.75.4.2.2.1.18 | IpAddress | RC | |
column · IpAddress · read-create · current Represents the IP address of the Wlanex Authentication server | ||||
| Chh3cDot11SPBeaconMeasEnable | 1.3.6.1.4.1.25506.2.75.4.2.2.1.19 | TruthValue | RC | |
column · TruthValue · read-create · current If it is true, then beacon-measurement is enabled. | ||||
| Chh3cDot11SPBeaconMeasType | 1.3.6.1.4.1.25506.2.75.4.2.2.1.20 | INTEGER | RC | |
column · INTEGER · read-create · current Represents what the work mode for BeaconMeasurement type. The following values are supported: passive, - BeaconMeasurement will use the passive type. active - BeaconMeasurement will use the active type. beaconTable - BeaconMeasurement will use the beacon table type.
| ||||
| Chh3cDot11SPBeaconMeasInterval | 1.3.6.1.4.1.25506.2.75.4.2.2.1.21 | Integer32 (10..200) | RC | |
column · Integer32 (10..200) · read-create · current Represents the beacon-measurement interval.
| ||||
| Chh3cDot11AuthenModeCM | 1.3.6.1.4.1.25506.2.75.4.2.2.1.22 | INTEGER | RC | |
column · INTEGER · read-create · current Represents the Authentication mode defined by 802.11.
| ||||
| Chh3cDot11SecIEStatusCM | 1.3.6.1.4.1.25506.2.75.4.2.2.1.23 | INTEGER | RC | |
column · INTEGER · read-create · current To enable the security Information element in the beacon and probe response frames sent by AP.
| ||||
| Chh3cDot11SecurityCiphersCM | 1.3.6.1.4.1.25506.2.75.4.2.2.1.24 | INTEGER | RC | |
column · INTEGER · read-create · current The WLAN system support the following cipher type for data frame encryption. none wep40 wep104 tkip aesccmp wpi-SMS4 When the value of node equals to zero, it means no configuration or undo operation.
| ||||
| Chh3cDot11SrvPolicyStatusCM | 1.3.6.1.4.1.25506.2.75.4.2.2.1.25 | INTEGER | RC | |
column · INTEGER · read-create · current The status of the Service Policy.
| ||||
| Chh3cDot11SSIDHiddenCM | 1.3.6.1.4.1.25506.2.75.4.2.2.1.26 | Hh3cDot11TruthValueCM | RC | |
column · Hh3cDot11TruthValueCM · read-create · current This attribute controls whether the SSID will be advertised in beacon frames. If it is dot11true, the SSID will not be advertised in beacon frames. | ||||
| Chh3cDot11SPIsolateCM | 1.3.6.1.4.1.25506.2.75.4.2.2.1.27 | Hh3cDot11TruthValueCM | RC | |
column · Hh3cDot11TruthValueCM · read-create · current If it is dot11true, the clients connected with the service policy are isolated to each other. | ||||
| Chh3cDot11FwdVlanBitMapLow | 1.3.6.1.4.1.25506.2.75.4.2.2.1.28 | OCTET STRING (SIZE (0..256)) | RC | |
column · OCTET STRING (SIZE (0..256)) · read-create · current Each octet within this value specifies a set of eight VLANs, with the first octet specifying VLANs 1 through 8, the second octet specifying VLANs 9 through 16, etc. Within each octet, the most significant bit represents the highest numbered VLAN, and the least significant bit represents the lowest numbered VLAN. Thus, each untagged VLAN of the hybrid port is represented by a single bit within the value of this object. If that bit has a value of '1' then that VLAN is untagged in the set of VLANs; the VLAN is not untagged if its bit has a value of '0'. | ||||
| Chh3cDot11FwdVlanBitMapHigh | 1.3.6.1.4.1.25506.2.75.4.2.2.1.29 | OCTET STRING (SIZE (0..256)) | RC | |
column · OCTET STRING (SIZE (0..256)) · read-create · current Each octet within this value specifies a set of eight VLANs, with the first octet specifying VLANs 1 through 8, the second octet specifying VLANs 9 through 16, etc. Within each octet, the most significant bit represents the highest numbered VLAN, and the least significant bit represents the lowest numbered VLAN. Thus, each untagged VLAN of the hybrid port is represented by a single bit within the value of this object. If that bit has a value of '1' then that VLAN is untagged in the set of VLANs; the VLAN is not untagged if its bit has a value of '0'. | ||||
| Chh3cDot11ServicePolicyName | 1.3.6.1.4.1.25506.2.75.4.2.2.1.30 | OCTET STRING | RC | |
column · OCTET STRING · read-create · current Represents the name of each service policy. | ||||
| Chh3cDot11SecurityModeCM | 1.3.6.1.4.1.25506.2.75.4.2.2.1.31 | INTEGER | RW | |
column · INTEGER · read-write · current Determines the security modes of the WLAN port. none - The default value. No security mode is set. psk - Access to the port is denied until the port client is authorized (by 802.1X key negotiation). radius - Access to the port is denied until the port client is authorized (by 802.1X). wlanex - Access to the port is denied until the port client is authenticated by wlan cert.
| ||||
| Chh3cDot11SPInCbsValue | 1.3.6.1.4.1.25506.2.75.4.2.2.1.32 | Integer32 | RC | |
column · Integer32 · read-create · current Represents the CBS of inbound direction of this service policy. If the value is 0, it means that the CBS is automatically calculated from the value of CIR.
| ||||
| Chh3cDot11SPOutCbsValue | 1.3.6.1.4.1.25506.2.75.4.2.2.1.33 | Integer32 | RC | |
column · Integer32 · read-create · current Represents the CBS of outbound direction of this service policy. If the value is 0, it means that the CBS is automatically calculated from the value of CIR.
| ||||
| Chh3cDot11WlanInfCustomerPVID | 1.3.6.1.4.1.25506.2.75.4.2.2.1.34 | Integer32 | RC | |
column · Integer32 · read-create · current Represents the customer PVID. | ||||
| Thh3cDot11ServicePolicyExtTable | 1.3.6.1.4.1.25506.2.75.4.2.3 | NA | ||
table · not-accessible · current The table defines the parameters for ESS, as per service policy of CLI. When the value of hh3cDot11SSIDEncryptionMode equals to cipher(2), more configuration for a ESS will be put into the table. | ||||
| Rhh3cDot11ServicePolicyExtEntry | 1.3.6.1.4.1.25506.2.75.4.2.3.1 | NA | ||
row · not-accessible · current Each entry contains information of each service policy under cipher(2) mode. | ||||
| Chh3cDot11ServicePolicyExtID | 1.3.6.1.4.1.25506.2.75.4.2.3.1.1 | Hh3cDot11ServicePolicyIDType | NA | |
column · Hh3cDot11ServicePolicyIDType · not-accessible · current Represents the ID of each service policy. | ||||
| Chh3cDot11SecIEStatus | 1.3.6.1.4.1.25506.2.75.4.2.3.1.2 | Hh3cDot11SecIEStatusType | RC | |
column · Hh3cDot11SecIEStatusType · read-create · current To enable the security Information element in the beacon and probe response frames sent by AP. | ||||
| Chh3cDot11SecurityCiphers | 1.3.6.1.4.1.25506.2.75.4.2.3.1.3 | Integer32 | RC | |
column · Integer32 · read-create · current The WLAN system support the following cipher type for data frame encryption. wep40(2) tkip(4) aesccmp(16) wep104(32) wpisms4(64) wep128(128) For each service policy, it could support multiple cipher types at the same time. So the value of object could combine multiple value of cipher type above. When the value of node equals to zero, it means no configuration or undo operation. | ||||
| Chh3cDot11CipherKeyIndex | 1.3.6.1.4.1.25506.2.75.4.2.3.1.4 | Integer32 | RC | |
column · Integer32 · read-create · current Represents the key index of cipher key for packet. When hh3cDot11SecurityCiphers value is wep40 or wep104, the configuration will take effective. | ||||
| Chh3cDot11CipherKey | 1.3.6.1.4.1.25506.2.75.4.2.3.1.5 | OCTET STRING | RC | |
column · OCTET STRING · read-create · current Represents the cipher key for packet. When hh3cDot11SecurityCiphers value is wep40 or wep104, the configuration will take effective. | ||||
| Chh3cDot11SrvPolicyExtRowStatus | 1.3.6.1.4.1.25506.2.75.4.2.3.1.6 | RowStatus | RC | |
column · RowStatus · read-create · current The status of this table entry. | ||||
| Chh3cDot11CipherKeyType | 1.3.6.1.4.1.25506.2.75.4.2.3.1.7 | INTEGER | RC | |
column · INTEGER · read-create · current Represents the cipher key type of hh3cDot11CipherKey.
| ||||
| Chh3cDot11AkmMode | 1.3.6.1.4.1.25506.2.75.4.2.3.1.8 | INTEGER | RC | |
column · INTEGER · read-create · current The authentication and key management mode.
| ||||
| Chh3cDot11PskKey | 1.3.6.1.4.1.25506.2.75.4.2.3.1.9 | OCTET STRING | RC | |
column · OCTET STRING · read-create · current Represents the preshared key. This configuration takes effect if the hh3cDot11AkmMode value is psk. | ||||
| Thh3cDot11RadioPolicyExtTable | 1.3.6.1.4.1.25506.2.75.4.2.4 | NA | ||
table · not-accessible · current The table defines the radio policy of each radio. It can't be modified if the radio policy is a default radio policy. | ||||
| Rhh3cDot11RadioPolicyExtEntry | 1.3.6.1.4.1.25506.2.75.4.2.4.1 | NA | ||
row · not-accessible · current Each entry contains information of each radio policy. | ||||
| Chh3cDot11RPAPSerialID | 1.3.6.1.4.1.25506.2.75.4.2.4.1.1 | OCTET STRING (SIZE (0..127)) | NA | |
column · OCTET STRING (SIZE (0..127)) · not-accessible · current This object represents the Serial ID of AP. | ||||
| Chh3cDot11RPRadioID | 1.3.6.1.4.1.25506.2.75.4.2.4.1.2 | Hh3cDot11RadioScopeType | NA | |
column · Hh3cDot11RadioScopeType · not-accessible · current This object represents each radio. | ||||
| Chh3cDot11RPBeaconInterval | 1.3.6.1.4.1.25506.2.75.4.2.4.1.3 | Integer32 | RW | |
column · Integer32 · read-write · current This object represents the interval for Beacon management frame.
| ||||
| Chh3cDot11RPDtimInterval | 1.3.6.1.4.1.25506.2.75.4.2.4.1.4 | Integer32 | RW | |
column · Integer32 · read-write · current This object represents the number of beacon intervals that shall elapse between transmissions of Beacons frames containing a Traffic Indication Map (TIM) element whose DTIM count field is 0. This value is transmitted in the Delivery TIM (DTIM) Period field of Beacon frames. | ||||
| Chh3cDot11RPRtsThreshold | 1.3.6.1.4.1.25506.2.75.4.2.4.1.5 | Integer32 | RW | |
column · Integer32 · read-write · current This object represents the current minimum size, in octets, of the MAC protocol data unit (MPDU), below which a Request to send/Clear to send (RTS/CTS) handshake shall not be performed.
| ||||
| Chh3cDot11RPFragThreshold | 1.3.6.1.4.1.25506.2.75.4.2.4.1.6 | Integer32 | RW | |
column · Integer32 · read-write · current This object represents the current maximum size, in octets, of the MPDU that may be delivered to the PHY. A MSDU shall be broken into fragments if its size exceeds the value of this attribute after adding MAC headers and trailers.
| ||||
| Chh3cDot11RPShortRetryThreshold | 1.3.6.1.4.1.25506.2.75.4.2.4.1.7 | Integer32 | RW | |
column · Integer32 · read-write · current This object represents the maximum number of transmission attempts of a frame, the length of which is less than or equal to hh3cDot11RTSThreshold, that shall be made before a failure condition is indicated. | ||||
| Chh3cDot11RPLongRetryThreshold | 1.3.6.1.4.1.25506.2.75.4.2.4.1.8 | Integer32 | RW | |
column · Integer32 · read-write · current This object represents the maximum number of transmission attempts of a frame, the length of which is longer than hh3cDot11RTSThreshold, and that shall be made before a failure condition is indicated. | ||||
| Chh3cDot11RPClientMaxCount | 1.3.6.1.4.1.25506.2.75.4.2.4.1.9 | Integer32 (0..2147483647) | RW | |
column · Integer32 (0..2147483647) · read-write · current This object represents the maximum number of stations supported by this radio policy. | ||||
| Chh3cDot11RPBeaconIntervalCM | 1.3.6.1.4.1.25506.2.75.4.2.4.1.10 | Integer32 | RW | |
column · Integer32 · read-write · current This object represents beacon interval.
| ||||
| Thh3cDot11SrvPortSecurityTable | 1.3.6.1.4.1.25506.2.75.4.2.5 | NA | ||
table · not-accessible · current This table defines the WLAN security status for ESS, BSS and WLAN-Ethernet interface which binding the crypto service-template. Otherwise, when binding the clear service-template, hh3cPortSecurityTables should be used to configure port security. | ||||
| Rhh3cDot11SrvPortSecurityEntry | 1.3.6.1.4.1.25506.2.75.4.2.5.1 | NA | ||
row · not-accessible · current There is a row in this table for service policy. | ||||
| Chh3cDot11SecurityServicePolicyID | 1.3.6.1.4.1.25506.2.75.4.2.5.1.1 | Hh3cDot11ServicePolicyIDType | NA | |
column · Hh3cDot11ServicePolicyIDType · not-accessible · current Represents the ID of each service policy. | ||||
| Chh3cDot11SrvPortSecurityMode | 1.3.6.1.4.1.25506.2.75.4.2.5.1.2 | INTEGER | RW | |
column · INTEGER · read-write · current Determines the security modes of the WLAN port. noRestrictions The default value, no any security mode is set. userLoginSecureExt Access to the port is denied until the port client is authorized (by 802.1X). psk Access to the port is denied until the port client is authorized (by 802.1X key negotiation). macAddressAndPsk The MAC address is first authenticated and only if this succeeds does the psk then attempt user authentication. userLoginSecureExtOrPsk This selects both the userLoginSecureExt and psk modes together such that either is allowed to authorized access. Which mode works for client depends on the client's choice. ext Access to the port is denied until the port client is authenticated (by ext).
| ||||
| Chh3cDot11SrvSecurityKeyType | 1.3.6.1.4.1.25506.2.75.4.2.5.1.3 | INTEGER | RW | |
column · INTEGER · read-write · current This indicates the key type in the 802.1X EAPOL_Key packet. userLoginTxKeyTypeNone - This means the key type is not set yet. userLoginTxKeyTypeDot11Key - This selects the 802.11 key type. userLoginTxKeyTypeRsaRC4Key - This selects the RC4 key for RSA RC4 session encryption.
| ||||
| Chh3cDot11SrvSecurityPskKeyMode | 1.3.6.1.4.1.25506.2.75.4.2.5.1.4 | INTEGER | RW | |
column · INTEGER · read-write · current This is the password input mode. When input as pskKeyModePassPhrase, hh3cDot11SrvSecurityPskKeyString must be 8 to 63 characters; when input as pskKeyModeRawKey, hh3cDot11SrvSecurityPskKeyString must be 64 characters and each character must be '0'-'9', 'a'-'f' and 'A'-'F'.
| ||||
| Chh3cDot11SrvSecurityPskKeyString | 1.3.6.1.4.1.25506.2.75.4.2.5.1.5 | DisplayString (SIZE (0..64)) | RW | |
column · DisplayString (SIZE (0..64)) · read-write · current This is the password string used for psk authentication. | ||||
| Chh3cDot11SrvPortSecurityModeCM | 1.3.6.1.4.1.25506.2.75.4.2.5.1.6 | INTEGER | RW | |
column · INTEGER · read-write · current Determines the security modes of the WLAN port. none - The default value, no any security mode is set. psk - Access to the port is denied until the port client is authorized (by 802.1X key negotiation). radius - Access to the port is denied until the port client is authorized (by 802.1X). wlanex - Access to the port is denied until the port client is authenticated by wlan cert.
| ||||
| Thh3cDot11SrvPolicyExtendTable | 1.3.6.1.4.1.25506.2.75.4.2.6 | NA | ||
table · not-accessible · current The table defines the parameters of each service policy. | ||||
| Rhh3cDot11SrvPolicyExtendEntry | 1.3.6.1.4.1.25506.2.75.4.2.6.1 | NA | ||
row · not-accessible · current Each entry contains information of each service policy. | ||||
| Chh3cDot11SPEnable | 1.3.6.1.4.1.25506.2.75.4.2.6.1.1 | INTEGER | RW | |
column · INTEGER · read-write · current Represents whether the service policy is enabled.
| ||||
| Thh3cDot11SrvL2AuthenTable | 1.3.6.1.4.1.25506.2.75.4.2.7 | NA | ||
table · not-accessible · current This table defines the Layer 2 authentication status of service templates. | ||||
| Rhh3cDot11SrvL2AuthenEntry | 1.3.6.1.4.1.25506.2.75.4.2.7.1 | NA | ||
| Chh3cDot11SrvL2AuthenID | 1.3.6.1.4.1.25506.2.75.4.2.7.1.1 | Hh3cDot11ServicePolicyIDType | NA | |
column · Hh3cDot11ServicePolicyIDType · not-accessible · current Represents the ID of a service template. | ||||
| Chh3cDot11L2AuthenMode | 1.3.6.1.4.1.25506.2.75.4.2.7.1.2 | INTEGER | RW | |
column · INTEGER · read-write · current Authentication mode of the service template. bypass No authentication is required. macAuthentication MAC authentication. macThenDot1xAuthentication MAC authentication is executed first. If MAC authentication fails, 802.1X authentication is executed. dot1xAuthentication Access to the port is denied until the client is authorized by 802.1X. dot1xThenMacAuthentication 802.1X authentication is executed first. If 802.1X authentication fails , MAC authentication is executed. ouiThenDot1x OUI authentication is first executed. If OUI authentication fails, 802.1X authentication is executed.
| ||||
| Chh3cDot11L2IntrusProtectEnable | 1.3.6.1.4.1.25506.2.75.4.2.7.1.3 | TruthValue | RW | |
column · TruthValue · read-write · current Enables intrusion protection for the service template. | ||||
| Chh3cDot11L2IntrusProtectOpt | 1.3.6.1.4.1.25506.2.75.4.2.7.1.4 | INTEGER | RW | |
column · INTEGER · read-write · current Operation mode when intrusion is detected.
| ||||
| Chh3cDot11TempServiceStopTimer | 1.3.6.1.4.1.25506.2.75.4.2.7.1.5 | Integer32 (10..300) | RW | |
column · Integer32 (10..300) · read-write · current Time period for temporarily stopping service. | ||||
| Chh3cDot11TempBlockMACTimer | 1.3.6.1.4.1.25506.2.75.4.2.7.1.6 | Integer32 (60..300) | RW | |
column · Integer32 (60..300) · read-write · current Time period for temporarily blocking user MACs. | ||||
| Chh3cDot11L2IgnoreAuthorization | 1.3.6.1.4.1.25506.2.75.4.2.7.1.7 | TruthValue | RW | |
column · TruthValue · read-write · current Ignores all authorization information set by the server. | ||||
| Chh3cDot11L2FailVLAN | 1.3.6.1.4.1.25506.2.75.4.2.7.1.8 | Integer32 (0..4094) | RW | |
column · Integer32 (0..4094) · read-write · current VLAN for authentication failure. 0 means not configured. | ||||
| Chh3cDot11L2CriticalVLAN | 1.3.6.1.4.1.25506.2.75.4.2.7.1.9 | Integer32 (0..4094) | RW | |
column · Integer32 (0..4094) · read-write · current VLAN for server unavailability situation. 0 means not configured. | ||||
| Chh3cDot11L2AuthorFailOffline | 1.3.6.1.4.1.25506.2.75.4.2.7.1.10 | TruthValue | RW | |
column · TruthValue · read-write · current Users are logged off if authorization fails. | ||||
| Chh3cDot11L2AccountFailOffline | 1.3.6.1.4.1.25506.2.75.4.2.7.1.11 | TruthValue | RW | |
column · TruthValue · read-write · current Users are logged off if accounting fails. | ||||
| Chh3cDot11Dot1xHSEnable | 1.3.6.1.4.1.25506.2.75.4.2.7.1.12 | TruthValue | RW | |
column · TruthValue · read-write · current Enables 802.1X handshake. | ||||
| Chh3cDot11Dot1xSecureHSEnable | 1.3.6.1.4.1.25506.2.75.4.2.7.1.13 | TruthValue | RW | |
column · TruthValue · read-write · current Enables secure 802.1X handshake. | ||||
| Chh3cDot11Dot1xReauthenEnable | 1.3.6.1.4.1.25506.2.75.4.2.7.1.14 | TruthValue | RW | |
column · TruthValue · read-write · current Enables 802.1X reauthentication. | ||||
| Chh3cDot11Dot1xMandatoryDomain | 1.3.6.1.4.1.25506.2.75.4.2.7.1.15 | OCTET STRING | RW | |
column · OCTET STRING · read-write · current 802.1X authentication domain of users for the service template. | ||||
| Chh3cDot11Dot1xMaxUserCount | 1.3.6.1.4.1.25506.2.75.4.2.7.1.16 | Integer32 | RW | |
column · Integer32 · read-write · current Maximum number of 802.1X users supported by the BSS bound to the service template. | ||||
| Chh3cDot11MACAuthenDomain | 1.3.6.1.4.1.25506.2.75.4.2.7.1.17 | OCTET STRING | RW | |
column · OCTET STRING · read-write · current MAC authentication domain of users for the service template. | ||||
| Chh3cDot11MACAuthenMaxUserCount | 1.3.6.1.4.1.25506.2.75.4.2.7.1.18 | Integer32 | RW | |
column · Integer32 · read-write · current Maximum number of MAC authentication users supported by the BSS bound to the service template. | ||||
| Thh3cDot11IPLearningTable | 1.3.6.1.4.1.25506.2.75.4.2.8 | NA | ||
table · not-accessible · current The table specifies the IP learning type and status of service templates. | ||||
| Rhh3cDot11IPLearningEntry | 1.3.6.1.4.1.25506.2.75.4.2.8.1 | NA | ||
row · not-accessible · current Each entry contains information about an IP learning entry. | ||||
| Chh3cDot11IPLearningServiceName | 1.3.6.1.4.1.25506.2.75.4.2.8.1.1 | OCTET STRING (SIZE (1..255)) | NA | |
column · OCTET STRING (SIZE (1..255)) · not-accessible · current Represents the service name. | ||||
| Chh3cDot11IPLearningType | 1.3.6.1.4.1.25506.2.75.4.2.8.1.2 | INTEGER | NA | |
column · INTEGER · not-accessible · current Represents the IP learning type.
| ||||
| Chh3cDot11IPLearningStatus | 1.3.6.1.4.1.25506.2.75.4.2.8.1.3 | TruthValue | RW | |
column · TruthValue · read-write · current Represents the ip learning status of the interface. Setting this attribute to true enables IP learning on the interface. | ||||
| Chh3cDot11IPLearningVlanBitMapL | 1.3.6.1.4.1.25506.2.75.4.2.8.1.4 | OCTET STRING (SIZE (1..256)) | RW | |
column · OCTET STRING (SIZE (1..256)) · read-write · current Each octet within this value specifies a set of eight VLANs, with the first octet specifying VLANs 1 through 8 and the second octet specifying VLANs 9 through 16, etc. Within each octet, the most significant bit represents the highest numbered VLAN, and the least significant bit represents the lowest numbered VLAN. Thus, each untagged VLAN of the hybrid port is represented by a single bit within the value of this object. If that bit has a value of '1', that VLAN is untagged in the set of VLANs; the VLAN is not untagged if its bit has a value of '0'. | ||||
| Chh3cDot11IPLearningVlanBitMapH | 1.3.6.1.4.1.25506.2.75.4.2.8.1.5 | OCTET STRING (SIZE (1..256)) | RW | |
column · OCTET STRING (SIZE (1..256)) · read-write · current Each octet within this value specifies a set of eight VLANs, with the first octet specifying VLANs 1 through 8 and the second octet specifying VLANs 9 through 16, etc. Within each octet, the most significant bit represents the highest numbered VLAN, and the least significant bit represents the lowest numbered VLAN. Thus, each untagged VLAN of the hybrid port is represented by a single bit within the value of this object. If that bit has a value of '1', that VLAN is untagged in the set of VLANs; the VLAN is not untagged if its bit has a value of '0'. | ||||
| Nhh3cDot11APConfigGroup | 1.3.6.1.4.1.25506.2.75.4.3 | |||
| Thh3cDot11APTemplateTable | 1.3.6.1.4.1.25506.2.75.4.3.1 | NA | ||
table · not-accessible · current By AP template CLI, administrator will configure the parameters of AP by convenience. Before AP boot up and connect to AC by CAPWAP tunnel, administrator will create AP template for each AP. When AP connect to AC, AC will assign configuration to AP by hh3cDot11APSerialID information in AP template. | ||||
| Rhh3cDot11APTemplateEntry | 1.3.6.1.4.1.25506.2.75.4.3.1.1 | NA | ||
row · not-accessible · current Each entry contains configuration information for each AP. | ||||
| Chh3cDot11APTemplateName | 1.3.6.1.4.1.25506.2.75.4.3.1.1.1 | OCTET STRING (SIZE (0..127)) | NA | |
column · OCTET STRING (SIZE (0..127)) · not-accessible · current Represents the name of AP template. | ||||
| Chh3cDot11APSerialID | 1.3.6.1.4.1.25506.2.75.4.3.1.1.2 | OCTET STRING | RC | |
column · OCTET STRING · read-create · current Represents AP serial id. | ||||
| Chh3cDot11TemplateAPModelAlias | 1.3.6.1.4.1.25506.2.75.4.3.1.1.3 | OCTET STRING | RC | |
column · OCTET STRING · read-create · current Represents the alias of AP model name. | ||||
| Chh3cDot11Description | 1.3.6.1.4.1.25506.2.75.4.3.1.1.4 | OCTET STRING | RC | |
column · OCTET STRING · read-create · current This attribute will give more information about AP. Administrator could suggest the location, owner or other information for each AP. If the value is set to NULL, the description will be removed. | ||||
| Chh3cDot11APWorkMode | 1.3.6.1.4.1.25506.2.75.4.3.1.1.5 | INTEGER | RC | |
column · INTEGER · read-create · current Represents what work mode for AP. The following values are supported: normal - AP will supply WLAN service. monitor - AP will be a monitor to find attack. hybrid - AP will supply WLAN service and Device detection is enabled.
| ||||
| Chh3cDot11APTemplateRowStatus | 1.3.6.1.4.1.25506.2.75.4.3.1.1.6 | RowStatus | RC | |
column · RowStatus · read-create · current The status of this table entry. | ||||
| Chh3cDot11APName | 1.3.6.1.4.1.25506.2.75.4.3.1.1.7 | OCTET STRING | RC | |
column · OCTET STRING · read-create · current Represents the AP name. | ||||
| Chh3cDot11StatisInterv | 1.3.6.1.4.1.25506.2.75.4.3.1.1.8 | Integer32 | RC | |
column · Integer32 · read-create · current Represents the interval of radio statistic.
| ||||
| Chh3cDot11APBroadcastProbeReply | 1.3.6.1.4.1.25506.2.75.4.3.1.1.9 | TruthValue | RC | |
column · TruthValue · read-create · current Represents enable the AP to reply broadcast probe or not. 'true' : The AP to reply broadcast probe is enabled. 'false': The AP to reply broadcast probe is disabled | ||||
| Chh3cDot11StaIdleTimerInterv | 1.3.6.1.4.1.25506.2.75.4.3.1.1.10 | Integer32 | RC | |
column · Integer32 · read-create · current Represents the interval for which the link between AP and STA ( power-save or awake ) can be idle.
| ||||
| Chh3cDot11StaKeepAliveTimerInterv | 1.3.6.1.4.1.25506.2.75.4.3.1.1.11 | Integer32 | RC | |
column · Integer32 · read-create · current Represents the interval of the keep alive requests sent between AP and STA.
| ||||
| Chh3cDot11APCir | 1.3.6.1.4.1.25506.2.75.4.3.1.1.12 | Integer32 | RC | |
column · Integer32 · read-create · current Represents the committed information rate between AP and AC.
| ||||
| Chh3cDot11APCbs | 1.3.6.1.4.1.25506.2.75.4.3.1.1.13 | Integer32 | RC | |
column · Integer32 · read-create · current Represents the committed burst size between AP and AC.
| ||||
| Chh3cDot11APPriorityLevel | 1.3.6.1.4.1.25506.2.75.4.3.1.1.14 | Integer32 (0..7) | RC | |
column · Integer32 (0..7) · read-create · current This object represents the connection priority for the AP. If the connection priority is 7, the AC is considered as the primary AC for the AP. | ||||
| Chh3cDot11APElementID | 1.3.6.1.4.1.25506.2.75.4.3.1.1.15 | Integer32 | RO | |
column · Integer32 · read-only · current This object represents the AP element ID. | ||||
| Chh3cDot11APDevDetectEnable | 1.3.6.1.4.1.25506.2.75.4.3.1.1.16 | TruthValue | RC | |
column · TruthValue · read-create · current Represents whether device detection is enabled or not. 'true' : Device detection is enabled. 'false': Device detection is disabled. If device detection is enabled, the AP will provide both device detection and WLAN data services. By default, the AP only provides WLAN data services. When an AP works in monitor mode, that is, the value of object hh3cDot11APWorkMode is monitor, device detection cannot be enabled with object hh3cDot11APDevDetectEnable. | ||||
| Chh3cDot11APGetIPMethod | 1.3.6.1.4.1.25506.2.75.4.3.1.1.17 | INTEGER | RC | |
column · INTEGER · read-create · current This object represents the method how AP gets IP address.
| ||||
| Chh3cDot11StatisIntervMode | 1.3.6.1.4.1.25506.2.75.4.3.1.1.18 | INTEGER | RC | |
column · INTEGER · read-create · current This object represents the mode of statics interval. normal - statics interval value between 10s to 240s realtime - statics interval value between 0s to 5s
| ||||
| Chh3cDot11ApTrapEnabled | 1.3.6.1.4.1.25506.2.75.4.3.1.1.19 | TruthValue | RW | |
column · TruthValue · read-write · current Represents whether the trap status is enabled or not. 'true' : Enable the trap status; 'false' : Disable the trap status. | ||||
| Chh3cDot11ApFmwUpdState | 1.3.6.1.4.1.25506.2.75.4.3.1.1.20 | INTEGER | RC | |
column · INTEGER · read-create · current Represents the status of version auto-update for an AP. The following values are supported: enable - AP version will be updated automatically. disable - AP version will not be updated automatically. inherit - The status will inherit value from apgroup-view or system-view.
| ||||
| Chh3cDot11StatisIntervModeCM | 1.3.6.1.4.1.25506.2.75.4.3.1.1.21 | INTEGER | RC | |
column · INTEGER · read-create · current This object represents the mode of statistic interval. off - statistic interval value between 10s to 240s on - statistic interval value between 0s to 5s
| ||||
| Chh3cDot11ApNasIDCM | 1.3.6.1.4.1.25506.2.75.4.3.1.1.22 | OCTET STRING | RC | |
column · OCTET STRING · read-create · current Represents the NAS-ID of current service policy for each specific radio of AP. | ||||
| Chh3cDot11ApCoveragetype | 1.3.6.1.4.1.25506.2.75.4.3.1.1.23 | INTEGER | RC | |
column · INTEGER · read-create · current This object represents the coverage type of AP. school - the coverage type is school traffic - the coverage type is traffic shop - the coverage type is shop company - the coverage type is company
| ||||
| Chh3cDot11APControlAddressState | 1.3.6.1.4.1.25506.2.75.4.3.1.1.24 | INTEGER | RC | |
column · INTEGER · read-create · current Represents the status of control address for an AP. The following values are supported: enable - AC rediscovery will be enabled. disable - AC rediscovery will be disabled.
| ||||
| Chh3cDot11APControlAddressIPv4 | 1.3.6.1.4.1.25506.2.75.4.3.1.1.25 | IpAddress | RC | |
column · IpAddress · read-create · current Represents an AC IPv4 address for AC rediscovery. | ||||
| Chh3cDot11APControlAddressIPv6 | 1.3.6.1.4.1.25506.2.75.4.3.1.1.26 | OCTET STRING | RC | |
column · OCTET STRING · read-create · current Represents an AC IPv6 address for AC rediscovery. | ||||
| Chh3cDot11APLocalACName | 1.3.6.1.4.1.25506.2.75.4.3.1.1.27 | OCTET STRING | RO | |
column · OCTET STRING · read-only · current Represents the local AC name the AP belongs to. | ||||
| Chh3cDot11APEchoInterval | 1.3.6.1.4.1.25506.2.75.4.3.1.1.28 | Integer32 | RW | |
column · Integer32 · read-write · current This object represents the echo-interval of the AP. | ||||
| Chh3cDot11APProvisionAPIPv4 | 1.3.6.1.4.1.25506.2.75.4.3.1.1.29 | IpAddress | RW | |
column · IpAddress · read-write · current Represents the IPv4 address of an AP. | ||||
| Chh3cDot11APProvisionIPv4Mask | 1.3.6.1.4.1.25506.2.75.4.3.1.1.30 | Integer32 (1..31) | RW | |
column · Integer32 (1..31) · read-write · current Represents the IPv4 address mask of an AP. | ||||
| Chh3cDot11APProvisionAPIPv6 | 1.3.6.1.4.1.25506.2.75.4.3.1.1.31 | OCTET STRING | RW | |
column · OCTET STRING · read-write · current Represents the IPv6 address of an AP. | ||||
| Chh3cDot11APProvisionIPv6PrefixLen | 1.3.6.1.4.1.25506.2.75.4.3.1.1.32 | Integer32 (1..128) | RW | |
column · Integer32 (1..128) · read-write · current Represents the IPv6 address prefix length of an AP. | ||||
| Chh3cDot11APProvisionACIPv4 | 1.3.6.1.4.1.25506.2.75.4.3.1.1.33 | IpAddress | RW | |
column · IpAddress · read-write · current Represents an AC IPv4 address for discovery. | ||||
| Chh3cDot11APProvisionACIpv6 | 1.3.6.1.4.1.25506.2.75.4.3.1.1.34 | OCTET STRING | RC | |
column · OCTET STRING · read-create · current Represents an AC IPv6 address for discovery. | ||||
| Chh3cDot11APProvisionGateWayIPV4 | 1.3.6.1.4.1.25506.2.75.4.3.1.1.35 | IpAddress | RW | |
column · IpAddress · read-write · current Represents the gateway IPv4 address for an AP. | ||||
| Chh3cDot11APProvisionGateWayIPV6 | 1.3.6.1.4.1.25506.2.75.4.3.1.1.36 | OCTET STRING | RC | |
column · OCTET STRING · read-create · current Represents thre gateway IPv6 address for an AP. | ||||
| Chh3cDot11APMapConfigFileName | 1.3.6.1.4.1.25506.2.75.4.3.1.1.37 | OCTET STRING | RC | |
column · OCTET STRING · read-create · current Represents the name of the AP MapConfigFile. | ||||
| Thh3cDot11RadioToConfigTable | 1.3.6.1.4.1.25506.2.75.4.3.2 | NA | ||
table · not-accessible · current Before AP connects to AC, administrator will configure radio parameter to each radio. | ||||
| Rhh3cDot11RadioToConfigEntry | 1.3.6.1.4.1.25506.2.75.4.3.2.1 | NA | ||
row · not-accessible · current Each entry contains configuration information for each radio. | ||||
| Chh3cDot11APTemplateNameCfg | 1.3.6.1.4.1.25506.2.75.4.3.2.1.1 | OCTET STRING (SIZE (0..127)) | NA | |
column · OCTET STRING (SIZE (0..127)) · not-accessible · current Represents the name of AP template. | ||||
| Chh3cDot11CfgRadioID | 1.3.6.1.4.1.25506.2.75.4.3.2.1.2 | Hh3cDot11RadioScopeType | NA | |
column · Hh3cDot11RadioScopeType · not-accessible · current Represents each radio. | ||||
| Chh3cDot11CfgRadioPolicyName | 1.3.6.1.4.1.25506.2.75.4.3.2.1.3 | OCTET STRING | RW | |
column · OCTET STRING · read-write · current Represents the name of radio policy. | ||||
| Chh3cDot11CfgRadioType | 1.3.6.1.4.1.25506.2.75.4.3.2.1.4 | Hh3cDot11RadioType | RW | |
column · Hh3cDot11RadioType · read-write · current Represents the radio will work with which 802.11 radio type. | ||||
| Chh3cDot11CfgChannel | 1.3.6.1.4.1.25506.2.75.4.3.2.1.5 | Hh3cDot11ChannelScopeType | RW | |
column · Hh3cDot11ChannelScopeType · read-write · current Represents the channel allocation of radio. | ||||
| Chh3cDot11CfgMaxTxPowerLevel | 1.3.6.1.4.1.25506.2.75.4.3.2.1.6 | Hh3cDot11TxPwrLevelScopeType | RW | |
column · Hh3cDot11TxPwrLevelScopeType · read-write · current Represents the maximal transmit power scope for AP.
| ||||
| Chh3cDot11PreambleLen | 1.3.6.1.4.1.25506.2.75.4.3.2.1.7 | Hh3cDot11PreambleType | RW | |
column · Hh3cDot11PreambleType · read-write · current Represents whether use long or short preamble for 802.11 MAC frame. When hh3cDot11CfgRadioType is either dot11b, dot11g or dot11gn, then value for hh3cDot11PreambleLen will be valid. Otherwise, the value for it will be invalid. | ||||
| Chh3cDot11CfgRadioStatus | 1.3.6.1.4.1.25506.2.75.4.3.2.1.8 | TruthValue | RW | |
column · TruthValue · read-write · current Represents the radio admin status whether is enabled or disabled. | ||||
| Chh3cDot11CfgRdElementID | 1.3.6.1.4.1.25506.2.75.4.3.2.1.9 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current Represents the element ID of this radio. It comprises two parts. The highest 24 bits are AP element ID and the lowest 8 bits are radio ID. | ||||
| Chh3cDot11CfgWorkMode | 1.3.6.1.4.1.25506.2.75.4.3.2.1.10 | Hh3cDot11WorkMode | RW | |
column · Hh3cDot11WorkMode · read-write · current Represents work mode of the radio. | ||||
| Chh3cDot11CfgPwrAttValue | 1.3.6.1.4.1.25506.2.75.4.3.2.1.11 | Integer32 | RW | |
column · Integer32 · read-write · current Represents the value of power attenuation. | ||||
| Chh3cDot11RadioTxArithmetic | 1.3.6.1.4.1.25506.2.75.4.3.2.1.12 | INTEGER | RW | |
column · INTEGER · read-write · current Represents the transmission arithmetic of the radio. The following values are supported: quality - Consider the quality first during the transmission. bandwidth - Consider the bandwidth first during the transmission.
| ||||
| Chh3cDot11CfgChannelLockStat | 1.3.6.1.4.1.25506.2.75.4.3.2.1.13 | INTEGER | RW | |
column · INTEGER · read-write · current Represents locked status of channel on the radio.
| ||||
| Chh3cDot11CfgPowerLockStat | 1.3.6.1.4.1.25506.2.75.4.3.2.1.14 | INTEGER | RW | |
column · INTEGER · read-write · current Represents locked status of power on the radio.
| ||||
| Chh3cDot11CfgLBRdGroupId | 1.3.6.1.4.1.25506.2.75.4.3.2.1.15 | Unsigned32 | RW | |
column · Unsigned32 · read-write · current Represents the load balance group ID allocated for the radio. | ||||
| Chh3cDot11CfgRRMSDRdGroupId | 1.3.6.1.4.1.25506.2.75.4.3.2.1.16 | Unsigned32 | RW | |
column · Unsigned32 · read-write · current Represents the RRM self-decisive group ID allocated for the radio. | ||||
| Chh3cDot11CfgRadioType2 | 1.3.6.1.4.1.25506.2.75.4.3.2.1.17 | Hh3cDot11RadioType2 | RW | |
column · Hh3cDot11RadioType2 · read-write · current Represents the radio will work with which 802.11 radio type. | ||||
| Chh3cDot11CfgIDSEnable | 1.3.6.1.4.1.25506.2.75.4.3.2.1.18 | TruthValue | RW | |
column · TruthValue · read-write · current Represents whether intrusion detection is enabled for this radio. | ||||
| Chh3cDot11CfgSaEnable | 1.3.6.1.4.1.25506.2.75.4.3.2.1.19 | TruthValue | RW | |
column · TruthValue · read-write · current Represents whether spectrum analysis is enabled. | ||||
| Chh3cDot11CfgSaCltRtFFTData | 1.3.6.1.4.1.25506.2.75.4.3.2.1.20 | TruthValue | RW | |
column · TruthValue · read-write · current Represents whether to collect real-time FFT data for this radio. | ||||
| Chh3cDot11CfgSaBand | 1.3.6.1.4.1.25506.2.75.4.3.2.1.21 | INTEGER | RW | |
column · INTEGER · read-write · current Represents which band of channels will be monitored when collection real-time FFT data is enabled for this radio. Detection of interference devices and air quality will also be affected. Each band responds to the following channels. dot11g (Channels 1-14) dot11aLower (channels 36-64) dot11aMiddle (channels 100-140) dot11aUpper (channels 149-165).
| ||||
| Chh3cDot11CfgSaRptDevType | 1.3.6.1.4.1.25506.2.75.4.3.2.1.22 | Bits | RW | |
column · Bits · read-write · current Represents which types of interference devices should be reported.
| ||||
| Chh3cDot11CfgSaTrapDevEnable | 1.3.6.1.4.1.25506.2.75.4.3.2.1.23 | TruthValue | RW | |
column · TruthValue · read-write · current Represents whether trap is enabled for an interference device type. | ||||
| Chh3cDot11CfgSaTrapDevType | 1.3.6.1.4.1.25506.2.75.4.3.2.1.24 | Bits | RW | |
column · Bits · read-write · current Represents for which interference device types the AP will send traps when trap sending is enabled.
| ||||
| Chh3cDot11CfgSaTrapAQEnable | 1.3.6.1.4.1.25506.2.75.4.3.2.1.25 | TruthValue | RW | |
column · TruthValue · read-write · current Represents whether the channel quality trap is enabled. | ||||
| Chh3cDot11CfgSaTrapAQThreshold | 1.3.6.1.4.1.25506.2.75.4.3.2.1.26 | Integer32 (1..100) | RW | |
column · Integer32 (1..100) · read-write · current Represents the channel quality threshold. When the channel quality is below this value, the channel quality trap will be sent. | ||||
| Chh3cDot11CfgSaDrivenRRMEnable | 1.3.6.1.4.1.25506.2.75.4.3.2.1.27 | TruthValue | RW | |
column · TruthValue · read-write · current Configures whether to run RRM when the AP detects a certain level of interference. | ||||
| Chh3cDot11CfgSaDrivenRRMSnt | 1.3.6.1.4.1.25506.2.75.4.3.2.1.28 | INTEGER | RW | |
column · INTEGER · read-write · current Configures the threshold for triggering RRM. When the interference level for the AP exceeds the threshold , RRM initiates local dynamic frequency selection (DFS) and changes the channel of the affected radio to improve network performance. Low represents a decreased sensitivity to changes in the environment while high represents an increased sensitivity.
| ||||
| Chh3cDot11CfgSPInCirMode | 1.3.6.1.4.1.25506.2.75.4.3.2.1.29 | Hh3cDot11CirMode | RC | |
column · Hh3cDot11CirMode · read-create · current Specifies the committed information rate(CIR) mode for the inbound direction. This object is useful only when the corresponding CIR has a nonzero value. If the value of this object is changed, the corresponding CIR will be reset. | ||||
| Chh3cDot11CfgSPInCirValue | 1.3.6.1.4.1.25506.2.75.4.3.2.1.30 | Integer32 | RC | |
column · Integer32 · read-create · current Represents the CIR for the inbound direction of this service policy. If the value is 0, it means that no flow control is applied to the service policy, and the corresponding CIR mode is meaningless.
| ||||
| Chh3cDot11CfgSPOutCirMode | 1.3.6.1.4.1.25506.2.75.4.3.2.1.31 | Hh3cDot11CirMode | RC | |
column · Hh3cDot11CirMode · read-create · current Represents the committed information rate(CIR) mode for the outbound direction. This object is useful only when the corresponding CIR has a nonzero value. If the value of this object is changed, the corresponding CIR will be reset. | ||||
| Chh3cDot11CfgSPOutCirValue | 1.3.6.1.4.1.25506.2.75.4.3.2.1.32 | Integer32 | RC | |
column · Integer32 · read-create · current Represents the CIR for the outbound direction of this service policy. If the value is 0, it means that no flow control is applied to the service policy, and the corresponding CIR mode is meaningless.
| ||||
| Thh3cDot11APServiceSetTable | 1.3.6.1.4.1.25506.2.75.4.3.3 | NA | ||
table · not-accessible · current For each radio, it could configure multiple service policies. The table describes the relationship between radio and service policies. | ||||
| Rhh3cDot11APServiceSetEntry | 1.3.6.1.4.1.25506.2.75.4.3.3.1 | NA | ||
row · not-accessible · current Each entry contains service policy information for each specific radio of AP. | ||||
| Chh3cDot11CfgServicePolicyID | 1.3.6.1.4.1.25506.2.75.4.3.3.1.1 | Hh3cDot11ServicePolicyIDType | NA | |
column · Hh3cDot11ServicePolicyIDType · not-accessible · current Represents the ID of each service policy used by the AP. | ||||
| Chh3cDot11SrvSetRowStatus | 1.3.6.1.4.1.25506.2.75.4.3.3.1.2 | RowStatus | RC | |
column · RowStatus · read-create · current The status of this table entry. | ||||
| Chh3cDot11ServiceSetVlanId | 1.3.6.1.4.1.25506.2.75.4.3.3.1.3 | Integer32 (0..4094) | RC | |
column · Integer32 (0..4094) · read-create · current Represents the Vlan ID of BSS which is generated when service policy is binded with the Radio. | ||||
| Chh3cDot11ServiceSetVlanGroup | 1.3.6.1.4.1.25506.2.75.4.3.3.1.4 | OCTET STRING (SIZE (0..31)) | RC | |
column · OCTET STRING (SIZE (0..31)) · read-create · current Represents the VLAN group of the BSS generated when a service policy is bound to the radio. | ||||
| Thh3cDot11APSysInfoSetTable | 1.3.6.1.4.1.25506.2.75.4.3.4 | NA | ||
table · not-accessible · current The table of the system information for each AP. | ||||
| Rhh3cDot11APSysInfoSetEntry | 1.3.6.1.4.1.25506.2.75.4.3.4.1 | NA | ||
row · not-accessible · current The system information configuration for each AP. | ||||
| Chh3cDot11APSysNetID | 1.3.6.1.4.1.25506.2.75.4.3.4.1.1 | OCTET STRING (SIZE (0..127)) | RW | |
column · OCTET STRING (SIZE (0..127)) · read-write · current Represents the system Net ID for AP. | ||||
| Chh3cDot11APCpuUsageThreshold | 1.3.6.1.4.1.25506.2.75.4.3.4.1.2 | Integer32 (0..100) | RW | |
column · Integer32 (0..100) · read-write · current The CPU usage threshold for AP.
| ||||
| Chh3cDot11APMemUsageThreshold | 1.3.6.1.4.1.25506.2.75.4.3.4.1.3 | Integer32 (0..100) | RW | |
column · Integer32 (0..100) · read-write · current The memory usage threshold for AP.
| ||||
| Thh3cDot11APLimitTable | 1.3.6.1.4.1.25506.2.75.4.3.5 | NA | ||
table · not-accessible · current For each connected APs, administrator could configure a series of limits. This table describes the limit information for AP(s). | ||||
| Rhh3cDot11APLimitEntry | 1.3.6.1.4.1.25506.2.75.4.3.5.1 | NA | ||
row · not-accessible · current Each entry contains the limit information for each AP. | ||||
| Chh3cDot11APSsidNumLimit | 1.3.6.1.4.1.25506.2.75.4.3.5.1.1 | Integer32 (0..65535) | RW | |
column · Integer32 (0..65535) · read-write · current Represents the upper limit of service template binded with this AP. All radios of AP share this limit. Default value 0 : There is no upper limit of service template binded with this AP. | ||||
| Chh3cDot11APUserCntLimit | 1.3.6.1.4.1.25506.2.75.4.3.5.1.2 | Integer32 (0..65535) | RW | |
column · Integer32 (0..65535) · read-write · current Represents the upper limit of user which has access to this AP. All BSSs binded with AP share this limit. Default value 0 : There is no upper limit of user which has access to this AP. | ||||
| Chh3cDot11APUserThreshold | 1.3.6.1.4.1.25506.2.75.4.3.5.1.3 | Integer32 (0..65535) | RW | |
column · Integer32 (0..65535) · read-write · current Represents the threshold of user which has access to this AP. All BSSs binded with AP share this limit. If the user counter is overflow, the trap will be sent. Default value 0 : There is no threshold of user which has access to this AP. | ||||
| Thh3cDot11APIfSetTable | 1.3.6.1.4.1.25506.2.75.4.3.6 | NA | ||
table · not-accessible · current The table of the interface information for each AP. | ||||
| Rhh3cDot11APIfSetEntry | 1.3.6.1.4.1.25506.2.75.4.3.6.1 | NA | ||
row · not-accessible · current The interface information configuration for each AP. | ||||
| Chh3cDot11APSetIfIndex | 1.3.6.1.4.1.25506.2.75.4.3.6.1.1 | Integer32 | NA | |
column · Integer32 · not-accessible · current Represents the index for a interface. | ||||
| Chh3cDot11APIfAlias | 1.3.6.1.4.1.25506.2.75.4.3.6.1.2 | DisplayString | RW | |
column · DisplayString · read-write · current This object is an 'alias' name for the interface as specified by a network manager for AP. | ||||
| Thh3cDot11APServiceVlanTable | 1.3.6.1.4.1.25506.2.75.4.3.7 | NA | ||
table · not-accessible · current For all the radios on the AP, it could configure multiple service policies. The table describes the relationship between AP and service policies. | ||||
| Rhh3cDot11APServiceVlanEntry | 1.3.6.1.4.1.25506.2.75.4.3.7.1 | NA | ||
row · not-accessible · current Each entry contains service policy information for each AP. | ||||
| Chh3cDot11APServiceVlanSerialID | 1.3.6.1.4.1.25506.2.75.4.3.7.1.1 | OCTET STRING | NA | |
column · OCTET STRING · not-accessible · current This object represents AP serial id. | ||||
| Chh3cDot11APServiceVlanSPID | 1.3.6.1.4.1.25506.2.75.4.3.7.1.2 | Hh3cDot11ServicePolicyIDType | NA | |
column · Hh3cDot11ServicePolicyIDType · not-accessible · current This object represents the ID of each service policy used by the AP. | ||||
| Chh3cDot11APServiceVlanId | 1.3.6.1.4.1.25506.2.75.4.3.7.1.3 | Integer32 (0..4094) | RC | |
column · Integer32 (0..4094) · read-create · current This object represents the VLAN ID of BSS which is generated when the service policy is bound to the radio. | ||||
| Chh3cDot11APServiceVlanRowStatus | 1.3.6.1.4.1.25506.2.75.4.3.7.1.4 | RowStatus | RC | |
column · RowStatus · read-create · current This object represents the status of this table entry. | ||||
| Thh3cDot11RadioConfigTable | 1.3.6.1.4.1.25506.2.75.4.3.8 | NA | ||
table · not-accessible · current Before AP connects to AC, administrator will configure radio parameter to each radio. | ||||
| Rhh3cDot11RadioConfigEntry | 1.3.6.1.4.1.25506.2.75.4.3.8.1 | NA | ||
row · not-accessible · current Each entry contains configuration information for each radio. | ||||
| Chh3cDot11RCAPSerialID | 1.3.6.1.4.1.25506.2.75.4.3.8.1.1 | OCTET STRING (SIZE (0..127)) | NA | |
column · OCTET STRING (SIZE (0..127)) · not-accessible · current This object represents the Serial ID of AP. | ||||
| Chh3cDot11RCRadioID | 1.3.6.1.4.1.25506.2.75.4.3.8.1.2 | Hh3cDot11RadioScopeType | NA | |
column · Hh3cDot11RadioScopeType · not-accessible · current This object represents each radio. | ||||
| Chh3cDot11RCRadioType | 1.3.6.1.4.1.25506.2.75.4.3.8.1.3 | Hh3cDot11RadioType | RW | |
column · Hh3cDot11RadioType · read-write · current This object represents the radio will work with which 802.11 radio type. | ||||
| Chh3cDot11RCChannel | 1.3.6.1.4.1.25506.2.75.4.3.8.1.4 | Hh3cDot11ChannelScopeType | RW | |
column · Hh3cDot11ChannelScopeType · read-write · current This object represents the channel allocation of radio. | ||||
| Chh3cDot11RCPreambleLen | 1.3.6.1.4.1.25506.2.75.4.3.8.1.5 | Hh3cDot11PreambleType | RW | |
column · Hh3cDot11PreambleType · read-write · current This object represents whether use long or short preamble for 802.11 MAC frame. When hh3cDot11CfgRadioType is either dot11b, dot11g or dot11gn, then value for hh3cDot11PreambleLen will be valid. Otherwise, the value for it will be invalid. | ||||
| Chh3cDot11RCPwrAttValue | 1.3.6.1.4.1.25506.2.75.4.3.8.1.6 | Integer32 | RW | |
column · Integer32 · read-write · current This object represents the value of power attenuation. | ||||
| Chh3cDot11RCApPowerLevel | 1.3.6.1.4.1.25506.2.75.4.3.8.1.7 | Hh3cDot11TxPwrLevelScopeType | RW | |
column · Hh3cDot11TxPwrLevelScopeType · read-write · current Represents the maximal transmit power scope for AP.
| ||||
| Chh3cDot11RCDynamicChlState | 1.3.6.1.4.1.25506.2.75.4.3.8.1.8 | TruthValue | RW | |
column · TruthValue · read-write · current Enable/Disable dynamic channel selection. | ||||
| Chh3cDot11RCDynamicPowerState | 1.3.6.1.4.1.25506.2.75.4.3.8.1.9 | TruthValue | RW | |
column · TruthValue · read-write · current Enable/Disable dynamic power selection for the band. | ||||
| Chh3cDot11RCRadioStatus | 1.3.6.1.4.1.25506.2.75.4.3.8.1.10 | TruthValue | RW | |
column · TruthValue · read-write · current Represents the radio admin status whether is enabled or disabled. | ||||
| Chh3cDot11RCRadioRate | 1.3.6.1.4.1.25506.2.75.4.3.8.1.11 | OCTET STRING (SIZE (0..255)) | RW | |
column · OCTET STRING (SIZE (0..255)) · read-write · current Set data transmit rates for the radio, in the format of 1,2,5.5... For 802.11n radios, the format can be MCS X. The data transmit rates between AP and STA must fall into the configured rates. (Note: For 802.11n radios, the first value will be treated as a mandatory rate, and the second value will be treated as a supported rate. If you configure more than two rates, the configuration cannot take effect. If you configure only one rate, it is considered as the mandatory rate by default.) | ||||
| Chh3cDot11RCPwrAdjustStepLength | 1.3.6.1.4.1.25506.2.75.4.3.8.1.12 | Integer32 | RO | |
column · Integer32 · read-only · current Power adjustment step-length in dBm. | ||||
| Chh3cDot11RCRadioType2 | 1.3.6.1.4.1.25506.2.75.4.3.8.1.13 | Hh3cDot11RadioType2 | RW | |
column · Hh3cDot11RadioType2 · read-write · current This object represents the radio will work with which 802.11 radio type. | ||||
| Chh3cDot11RCPreambleLenCM | 1.3.6.1.4.1.25506.2.75.4.3.8.1.14 | INTEGER | RW | |
column · INTEGER · read-write · current This object represents whether use long or short preamble for 802.11 MAC frame. When hh3cDot11CfgRadioType is either dot11b, dot11g or dot11gn, then value for hh3cDot11PreambleLenCM will be valid. Otherwise, the value for it will be invalid.
| ||||
| Chh3cDot11RCDynamicChlStateCM | 1.3.6.1.4.1.25506.2.75.4.3.8.1.15 | INTEGER | RW | |
column · INTEGER · read-write · current Enable/Disable dynamic channel selection.
| ||||
| Chh3cDot11RCRadioStatusCM | 1.3.6.1.4.1.25506.2.75.4.3.8.1.16 | INTEGER | RW | |
column · INTEGER · read-write · current Represents the radio admin status whether is enabled or disabled.
| ||||
| Chh3cDot11RCRadioRateCM | 1.3.6.1.4.1.25506.2.75.4.3.8.1.17 | OCTET STRING (SIZE (0..255)) | RW | |
column · OCTET STRING (SIZE (0..255)) · read-write · current Set data transmit rates for the radio, in the format of 1,2,5.5... For 802.11n radios, the format of each value can be MCS X. The data transmit rates between AP and client should be one of the configured rates. (Note: For 802.11n radios, the first value is mandatory rate, and the second value is supported rate. If more than two rate values are configured, the configuration will not take effect. If only one rate value is configured, the mandatory rate will be set to the default value.) | ||||
| Chh3cDot11RCDynamicPowerStateCM | 1.3.6.1.4.1.25506.2.75.4.3.8.1.18 | Hh3cDot11TruthValueCM | RW | |
column · Hh3cDot11TruthValueCM · read-write · current Enable/disable dynamic power selection for the band. | ||||
| Chh3cDot11RCRssiThresholdCM | 1.3.6.1.4.1.25506.2.75.4.3.8.1.19 | Integer32 | RW | |
column · Integer32 · read-write · current Represents the minimum value of the RSSI. The clients with RSSI below this value will be refused to associate.
| ||||
| Chh3cDot11RCDynamicChlStateSelfDecisiveCM | 1.3.6.1.4.1.25506.2.75.4.3.8.1.20 | Hh3cDot11TruthValueCM | RW | |
column · Hh3cDot11TruthValueCM · read-write · current Enable/disable dynamic channel selection self decisive for the band. | ||||
| Chh3cDot11RCDynamicPowerStateSelfDecisiveCM | 1.3.6.1.4.1.25506.2.75.4.3.8.1.21 | Hh3cDot11TruthValueCM | RW | |
column · Hh3cDot11TruthValueCM · read-write · current Enable/disable dynamic power selection self decisive for the band. | ||||
| Thh3cDot11RadioSSIDCfgTable | 1.3.6.1.4.1.25506.2.75.4.3.9 | NA | ||
table · not-accessible · current For each radio, it could configure multiple service policies. The table describes the relationship between radio and service policies. | ||||
| Rhh3cDot11RadioSSIDCfgEntry | 1.3.6.1.4.1.25506.2.75.4.3.9.1 | NA | ||
row · not-accessible · current Each entry contains SSID configuration information for each radio. | ||||
| Chh3cDot11RadioSSIDSerialID | 1.3.6.1.4.1.25506.2.75.4.3.9.1.1 | Hh3cDot11ObjectIDType | NA | |
column · Hh3cDot11ObjectIDType · not-accessible · current This object represents the serial ID of AP. | ||||
| Chh3cDot11RadioSSIDRadioID | 1.3.6.1.4.1.25506.2.75.4.3.9.1.2 | Hh3cDot11RadioScopeType | NA | |
column · Hh3cDot11RadioScopeType · not-accessible · current This object represents each radio. | ||||
| Chh3cDot11RadioSSIDWLANID | 1.3.6.1.4.1.25506.2.75.4.3.9.1.3 | Integer32 | NA | |
column · Integer32 · not-accessible · current This object represents the WLAN ID of the BSSID. | ||||
| Chh3cDot11RadioSSIDIndex | 1.3.6.1.4.1.25506.2.75.4.3.9.1.4 | Hh3cDot11ServicePolicyIDType | RC | |
column · Hh3cDot11ServicePolicyIDType · read-create · current This object represents the ID of each service policy used by the radio. | ||||
| Chh3cDot11RadioBSSID | 1.3.6.1.4.1.25506.2.75.4.3.9.1.5 | MacAddress | RO | |
column · MacAddress · read-only · current As MAC address format, it is used to identify BSS. | ||||
| Chh3cDot11RadioSSIDRowStatus | 1.3.6.1.4.1.25506.2.75.4.3.9.1.6 | RowStatus | RC | |
column · RowStatus · read-create · current RowStatus. | ||||
| Thh3cDot11APSerialIDTable | 1.3.6.1.4.1.25506.2.75.4.3.10 | NA | ||
table · not-accessible · current The table will provide the general information about APs. | ||||
| Rhh3cDot11APSerialIDEntry | 1.3.6.1.4.1.25506.2.75.4.3.10.1 | NA | ||
row · not-accessible · current Each entry contains the general information of an AP. | ||||
| Chh3cDot11SIDAPSerialID | 1.3.6.1.4.1.25506.2.75.4.3.10.1.1 | OCTET STRING | NA | |
column · OCTET STRING · not-accessible · current Represents AP serial id. | ||||
| Chh3cDot11SIDAPWorkMode | 1.3.6.1.4.1.25506.2.75.4.3.10.1.2 | INTEGER | RC | |
column · INTEGER · read-create · current Represents what work mode for AP. The following values are supported: normal - AP will supply WLAN service. monitor - AP will be a monitor to find attack. hybrid - AP will supply WLAN service and Device detection is enabled.
| ||||
| Chh3cDot11SIDAPGetIPMethod | 1.3.6.1.4.1.25506.2.75.4.3.10.1.3 | INTEGER | RC | |
column · INTEGER · read-create · current This object represents the method how AP gets IP address.
| ||||
| Chh3cDot11SIDAPTemplateName | 1.3.6.1.4.1.25506.2.75.4.3.10.1.4 | OCTET STRING | RC | |
column · OCTET STRING · read-create · current Represents the name of AP template. | ||||
| Chh3cDot11SIDModelAlias | 1.3.6.1.4.1.25506.2.75.4.3.10.1.5 | OCTET STRING | RC | |
column · OCTET STRING · read-create · current Represents the alias of AP model name. | ||||
| Chh3cDot11SIDAPDescription | 1.3.6.1.4.1.25506.2.75.4.3.10.1.6 | OCTET STRING | RC | |
column · OCTET STRING · read-create · current This attribute will give more information about AP. Administrator could suggest the location, owner or other information for each AP. If the value is set to NULL, the description will be removed. | ||||
| Chh3cDot11SIDRowStatus | 1.3.6.1.4.1.25506.2.75.4.3.10.1.7 | RowStatus | RC | |
column · RowStatus · read-create · current The status of this table entry. | ||||
| Chh3cDot11SIDAPName | 1.3.6.1.4.1.25506.2.75.4.3.10.1.8 | OCTET STRING | RC | |
column · OCTET STRING · read-create · current Represents the AP name. | ||||
| Chh3cDot11SIDStatisInterv | 1.3.6.1.4.1.25506.2.75.4.3.10.1.9 | Integer32 | RC | |
column · Integer32 · read-create · current Represents the interval of radio statistic.
| ||||
| Chh3cDot11SIDAPBroadcastProbeReply | 1.3.6.1.4.1.25506.2.75.4.3.10.1.10 | TruthValue | RC | |
column · TruthValue · read-create · current Represents enable the AP to reply broadcast probe or not. 'true' : The AP to reply broadcast probe is enabled. 'false': The AP to reply broadcast probe is disabled | ||||
| Chh3cDot11SIDAPStaIdleTimerInterv | 1.3.6.1.4.1.25506.2.75.4.3.10.1.11 | Integer32 | RC | |
column · Integer32 · read-create · current Represents the interval for which the link between AP and STA ( power-save or awake ) can be idle.
| ||||
| Chh3cDot11SIDStaKeepAliveTimerInterv | 1.3.6.1.4.1.25506.2.75.4.3.10.1.12 | Integer32 | RC | |
column · Integer32 · read-create · current Represents the interval of the keep alive requests sent between AP and STA.
| ||||
| Chh3cDot11SIDAPCir | 1.3.6.1.4.1.25506.2.75.4.3.10.1.13 | Integer32 | RC | |
column · Integer32 · read-create · current Represents the committed information rate between AP and AC.
| ||||
| Chh3cDot11SIDAPCbs | 1.3.6.1.4.1.25506.2.75.4.3.10.1.14 | Integer32 | RC | |
column · Integer32 · read-create · current Represents the committed burst size between AP and AC.
| ||||
| Chh3cDot11SIDAPPriorityLevel | 1.3.6.1.4.1.25506.2.75.4.3.10.1.15 | Integer32 (0..7) | RC | |
column · Integer32 (0..7) · read-create · current This object represents the connection priority for the AP. If the connection priority is 7, the AC is considered as the primary AC for the AP. | ||||
| Chh3cDot11SIDAPElementID | 1.3.6.1.4.1.25506.2.75.4.3.10.1.16 | Integer32 | RO | |
column · Integer32 · read-only · current This object represents the AP element ID. | ||||
| Chh3cDot11SIDAPDevDetectEnable | 1.3.6.1.4.1.25506.2.75.4.3.10.1.17 | TruthValue | RC | |
column · TruthValue · read-create · current Represents whether device detection is enabled or not. 'true' : Device detection is enabled. 'false': Device detection is disabled. If device detection is enabled, the AP will provide both device detection and WLAN data services. By default, the AP only provides WLAN data services. When an AP works in monitor mode, that is, the value of object hh3cDot11APWorkMode is monitor, device detection can not be enabled with object hh3cDot11SIDAPDevDetectEnable. | ||||
| Chh3cDot11SIDAPStatisIntervMode | 1.3.6.1.4.1.25506.2.75.4.3.10.1.18 | INTEGER | RC | |
column · INTEGER · read-create · current This object represents the mode of statics interval. normal - statics interval value between 10s to 240s realtime - statics interval value between 0s to 5s
| ||||
| Chh3cDot11SIDAPWorkModeCM | 1.3.6.1.4.1.25506.2.75.4.3.10.1.19 | INTEGER | RC | |
column · INTEGER · read-create · current Represents what work mode for AP. The following values are supported: normal - AP will supply WLAN service. monitor - AP will be a monitor to find attack. SemiMonitor - AP will supply WLAN service and Device detection is enabled.
| ||||
| Chh3cDot11SIDEchoInterval | 1.3.6.1.4.1.25506.2.75.4.3.10.1.20 | Integer32 | RW | |
column · Integer32 · read-write · current Represents the interval for send echo requests.
| ||||
| Thh3cDot11APSTVlanTable | 1.3.6.1.4.1.25506.2.75.4.3.11 | NA | ||
table · not-accessible · current For each service policy, it could be bind to several VLANs. The table describes the relationship between VLAN and service policies. | ||||
| Rhh3cDot11APSTVlanEntry | 1.3.6.1.4.1.25506.2.75.4.3.11.1 | NA | ||
row · not-accessible · current Each entry contains VLAN and service policy information for each specific radio of AP. | ||||
| Chh3cDot11CfgSTVLANID | 1.3.6.1.4.1.25506.2.75.4.3.11.1.1 | Integer32 (0..4094) | RC | |
column · Integer32 (0..4094) · read-create · current Represents the VLAN that current Service Policy have bind to. | ||||
| Chh3cDot11CfgSTNASPortID | 1.3.6.1.4.1.25506.2.75.4.3.11.1.2 | OCTET STRING (SIZE (0..127)) | RO | |
column · OCTET STRING (SIZE (0..127)) · read-only · current Represents the NAS Port ID of current Service Policy for each specific radio of AP. | ||||
| Chh3cDot11CfgServiceSetRowStatus | 1.3.6.1.4.1.25506.2.75.4.3.11.1.3 | RowStatus | RC | |
column · RowStatus · read-create · current The status of this table entry. | ||||
| Chh3cDot11CfgSTNASID | 1.3.6.1.4.1.25506.2.75.4.3.11.1.4 | OCTET STRING (SIZE (0..127)) | RO | |
column · OCTET STRING (SIZE (0..127)) · read-only · current Represents the NAS ID of current Service Policy for each specific radio of AP. | ||||
| Nhh3cDot11RadioIntfConfigGroup | 1.3.6.1.4.1.25506.2.75.4.4 | |||
| Thh3cDot11RadioIntfConfigTable | 1.3.6.1.4.1.25506.2.75.4.4.1 | NA | ||
table · not-accessible · current The table defines the parameters for radio in AP, as per radio. | ||||
| Rhh3cDot11RadioIntfConfigEntry | 1.3.6.1.4.1.25506.2.75.4.4.1.1 | NA | ||
row · not-accessible · current Each entry contains information of each radio in AP.
| ||||
| Chh3cDot11RadioIfIdx | 1.3.6.1.4.1.25506.2.75.4.4.1.1.1 | Integer32 | NA | |
column · Integer32 · not-accessible · current Represents the Radio IfIndex of radio in AP. | ||||
| Chh3cDot11RadioCfgBeaconIntvl | 1.3.6.1.4.1.25506.2.75.4.4.1.1.2 | Integer32 | RW | |
column · Integer32 · read-write · current Represents the interval for Beacon management frame.
| ||||
| Chh3cDot11RadioCfgDtimIntvl | 1.3.6.1.4.1.25506.2.75.4.4.1.1.3 | Integer32 | RW | |
column · Integer32 · read-write · current Represents the number of beacon intervals that shall elapse between transmission of Beacons frames containing a Traffic Indication Map (TIM) element whose DTIM Count field is 0. This value is transmitted in the Delivery TIM (DTIM) Period field of Beacon frames. | ||||
| Chh3cDot11RadioCfgRtsThreshold | 1.3.6.1.4.1.25506.2.75.4.4.1.1.4 | Integer32 | RW | |
column · Integer32 · read-write · current Represents the current minimum size,in octets,of the MAC protocol data unit (MPDU), below which a Request to send/Clear to send (RTS/CTS) handshake shall not be performed.
| ||||
| Chh3cDot11RadioCfgFragThreshold | 1.3.6.1.4.1.25506.2.75.4.4.1.1.5 | Integer32 | RW | |
column · Integer32 · read-write · current Represents the current maximum size, in octets, of the MPDU that may be delivered to the PHY. A MSDU shall be broken into fragments if its size exceeds the value of this attribute after adding MAC headers and trailers.
| ||||
| Chh3cDot11RadioCfgShtRetryThld | 1.3.6.1.4.1.25506.2.75.4.4.1.1.6 | Integer32 | RW | |
column · Integer32 · read-write · current Represents the maximum number of transmission attempts of a frame, the length of which is less than or equal to hh3cDot11RadioRTSThreshold, that shall be made before a failure condition is indicated. | ||||
| Chh3cDot11RadioCfglongRtrThld | 1.3.6.1.4.1.25506.2.75.4.4.1.1.7 | Integer32 | RW | |
column · Integer32 · read-write · current Represents the maximum number of transmission attempts of a frame, the length of which is longer than hh3cDot11RadioRTSThreshold, that shall be made before a failure condition is indicated. | ||||
| Chh3cDot11RadioCfgMaxRxLifetime | 1.3.6.1.4.1.25506.2.75.4.4.1.1.8 | Unsigned32 | RW | |
column · Unsigned32 · read-write · current Represents the elapsed time. After the time specified by hh3cDot11RadioCfgMaxRxLifetime, the further attempts to reassemble the MSDU shall be terminated.
| ||||
| Chh3cDot11RadioCfgType | 1.3.6.1.4.1.25506.2.75.4.4.1.1.9 | Hh3cDot11RadioType | RW | |
column · Hh3cDot11RadioType · read-write · current Represents the radio will work with which 802.11 radio type. | ||||
| Chh3cDot11RadioCfgChannel | 1.3.6.1.4.1.25506.2.75.4.4.1.1.10 | Hh3cDot11ChannelScopeType | RW | |
column · Hh3cDot11ChannelScopeType · read-write · current Represents the channel allocation of radio. | ||||
| Chh3cDot11RadioCfgMaxTxPwrLvl | 1.3.6.1.4.1.25506.2.75.4.4.1.1.11 | Hh3cDot11TxPwrLevelScopeType | RW | |
column · Hh3cDot11TxPwrLevelScopeType · read-write · current Represents the maximal transmit power scope for AP.
| ||||
| Chh3cDot11RadioCfgPreambleLen | 1.3.6.1.4.1.25506.2.75.4.4.1.1.12 | Hh3cDot11PreambleType | RW | |
column · Hh3cDot11PreambleType · read-write · current Represents whether use long or short preamble for 802.11 MAC frame. | ||||
| Chh3cDot11RadioCfgWorkMode | 1.3.6.1.4.1.25506.2.75.4.4.1.1.13 | Hh3cDot11WorkMode | RW | |
column · Hh3cDot11WorkMode · read-write · current Represents work mode of the radio. | ||||
| Chh3cDot11RadioCfgOnly11gEnable | 1.3.6.1.4.1.25506.2.75.4.4.1.1.14 | TruthValue | RW | |
column · TruthValue · read-write · current Represents whether enable only 802.11g radio mode or not. 'true' : Only 802.11g radio mode is enabled. 'false': Only 802.11g radio mode is disabled. | ||||
| Chh3cDot11RadioCfgType2 | 1.3.6.1.4.1.25506.2.75.4.4.1.1.15 | Hh3cDot11RadioType2 | RW | |
column · Hh3cDot11RadioType2 · read-write · current Represents the radio will work with which 802.11 radio type. | ||||
| Chh3cDot11RadioCfgRssithresholdCM | 1.3.6.1.4.1.25506.2.75.4.4.1.1.16 | Integer32 | RW | |
column · Integer32 · read-write · current Represents the minimum value of the RSSI. The clients with RSSI below this value will be refused to associate.
| ||||
| Thh3cDot11RadioIntfBindTable | 1.3.6.1.4.1.25506.2.75.4.4.2 | NA | ||
table · not-accessible · current The table defines the binding information for each radio in AP. | ||||
| Rhh3cDot11RadioIntfBindEntry | 1.3.6.1.4.1.25506.2.75.4.4.2.1 | NA | ||
row · not-accessible · current Each entry contains the radio interface binding information in AP. | ||||
| Chh3cDot11RadioIntfBindSvcPlcyID | 1.3.6.1.4.1.25506.2.75.4.4.2.1.1 | Hh3cDot11ServicePolicyIDType | NA | |
column · Hh3cDot11ServicePolicyIDType · not-accessible · current Represents the ID of each service policy. | ||||
| Chh3cDot11RadioIntfBindIfIdx | 1.3.6.1.4.1.25506.2.75.4.4.2.1.2 | Unsigned32 | RC | |
column · Unsigned32 · read-create · current Represents the Ifindex of interface which is binded to the radio. | ||||
| Chh3cDot11RadioIntfBindRowStatus | 1.3.6.1.4.1.25506.2.75.4.4.2.1.3 | RowStatus | RC | |
column · RowStatus · read-create · current The status of this table entry. | ||||
| Nhh3cDot11DataRateConfigGroup | 1.3.6.1.4.1.25506.2.75.4.5 | |||
| Thh3cDot11DataRateConfigTable | 1.3.6.1.4.1.25506.2.75.4.5.1 | NA | ||
table · not-accessible · current Table will provide data rate configuration for a specific radio type. | ||||
| Rhh3cDot11DataRateConfigEntry | 1.3.6.1.4.1.25506.2.75.4.5.1.1 | NA | ||
row · not-accessible · current Each entry of the table will provide data rate configuration for a specific radio type.
| ||||
| Chh3cDot11RadioTypeID | 1.3.6.1.4.1.25506.2.75.4.5.1.1.1 | Hh3cDot11RadioType | NA | |
column · Hh3cDot11RadioType · not-accessible · current Represents the radio type. | ||||
| Chh3cDot11SupportedRateSet | 1.3.6.1.4.1.25506.2.75.4.5.1.1.2 | OCTET STRING (SIZE (0..255)) | RW | |
column · OCTET STRING (SIZE (0..255)) · read-write · current Represents the supported rate set of a particular radio type. | ||||
| Chh3cDot11MandatoryRateSet | 1.3.6.1.4.1.25506.2.75.4.5.1.1.3 | OCTET STRING (SIZE (0..255)) | RW | |
column · OCTET STRING (SIZE (0..255)) · read-write · current Represents the mandatory rate set of a particular radio type. | ||||
| Chh3cDot11DisabledRateSet | 1.3.6.1.4.1.25506.2.75.4.5.1.1.4 | OCTET STRING (SIZE (0..255)) | RW | |
column · OCTET STRING (SIZE (0..255)) · read-write · current Represents the disabled rate set of a particular radio type. | ||||
| Chh3cDot11SmartRateSet | 1.3.6.1.4.1.25506.2.75.4.5.1.1.5 | OCTET STRING (SIZE (0..255)) | RW | |
column · OCTET STRING (SIZE (0..255)) · read-write · current Represents the rate set of a particular radio type. | ||||
| Nhh3cDot11InterfaceConfigGroup | 1.3.6.1.4.1.25506.2.75.4.6 | |||
| Thh3cDot11WlanEssIfTable | 1.3.6.1.4.1.25506.2.75.4.6.1 | NA | ||
table · not-accessible · current This table is used to configure WLAN ESS interface. | ||||
| Rhh3cDot11WlanEssIfEntry | 1.3.6.1.4.1.25506.2.75.4.6.1.1 | NA | ||
row · not-accessible · current Each entry contains the WLAN ESS interface configuration. | ||||
| Chh3cDot11WlanEssIfNumber | 1.3.6.1.4.1.25506.2.75.4.6.1.1.1 | Integer32 | NA | |
column · Integer32 · not-accessible · current This node represents the WLAN ESS interface number. | ||||
| Chh3cDot11WlanEssIfIndex | 1.3.6.1.4.1.25506.2.75.4.6.1.1.2 | Integer32 | RO | |
column · Integer32 · read-only · current This node represents the ifIndex of WLAN-ESS interface. | ||||
| Chh3cDot11WlanEssRowStatus | 1.3.6.1.4.1.25506.2.75.4.6.1.1.3 | RowStatus | RC | |
column · RowStatus · read-create · current This node represents the WLAN ESS interface row status. | ||||
| Thh3cDot11WlanBssIfTable | 1.3.6.1.4.1.25506.2.75.4.6.2 | NA | ||
table · not-accessible · current This table is used to configure WLAN BSS interface. | ||||
| Rhh3cDot11WlanBssIfEntry | 1.3.6.1.4.1.25506.2.75.4.6.2.1 | NA | ||
row · not-accessible · current Each entry contains the WLAN BSS interface configuration. | ||||
| Chh3cDot11WlanBssIfNumber | 1.3.6.1.4.1.25506.2.75.4.6.2.1.1 | Integer32 | NA | |
column · Integer32 · not-accessible · current This node represents the WLAN BSS interface number. | ||||
| Chh3cDot11WlanBssIfIndex | 1.3.6.1.4.1.25506.2.75.4.6.2.1.2 | Integer32 | RO | |
column · Integer32 · read-only · current This node represents the ifIndex of WLAN-BSS interface. | ||||
| Chh3cDot11WlanBssRowStatus | 1.3.6.1.4.1.25506.2.75.4.6.2.1.3 | RowStatus | RC | |
column · RowStatus · read-create · current This node represents the WLAN BSS interface row status. | ||||
| Thh3cDot11WLANEthernetIfTable | 1.3.6.1.4.1.25506.2.75.4.6.3 | NA | ||
table · not-accessible · current This table is used to configure WLAN Ethernet interface. | ||||
| Rhh3cDot11WLANEthernetIfEntry | 1.3.6.1.4.1.25506.2.75.4.6.3.1 | NA | ||
row · not-accessible · current Each entry contains the WLAN Ethernet interface configuration. | ||||
| Chh3cDot11WlanEthernetIfNumber | 1.3.6.1.4.1.25506.2.75.4.6.3.1.1 | Integer32 | NA | |
column · Integer32 · not-accessible · current This node represents the WLAN Ethernet interface number. | ||||
| Chh3cDot11WLANEthernetIfIndex | 1.3.6.1.4.1.25506.2.75.4.6.3.1.2 | Integer32 | RO | |
column · Integer32 · read-only · current This node represents the ifIndex of WLAN-Ethernet interface. | ||||
| Chh3cDot11WlanEthernetRowStatus | 1.3.6.1.4.1.25506.2.75.4.6.3.1.3 | RowStatus | RC | |
column · RowStatus · read-create · current This node represents the Wlan Ethernet interface row status. | ||||
| Thh3cDot11PortSecurityTable | 1.3.6.1.4.1.25506.2.75.4.6.4 | NA | ||
table · not-accessible · current This table defines the WLAN security status for ESS, BSS, mesh and WLAN-Ethernet interface which binding the crypto service-template. Otherwise, when binding the clear service-template, hh3cPortSecurityTables should be used to configure port security. | ||||
| Rhh3cDot11PortSecurityEntry | 1.3.6.1.4.1.25506.2.75.4.6.4.1 | NA | ||
row · not-accessible · current There is a row in this table for each ESS, BSS and WLAN-Ethernet interface.It is indexed using the object ifIndex in RFC1213-MIB.
| ||||
| Chh3cDot11PortSecurityMode | 1.3.6.1.4.1.25506.2.75.4.6.4.1.1 | INTEGER | RW | |
column · INTEGER · read-write · current Determines the security modes of the WLAN port. noRestrictions - The default value,no any security mode is set. userLoginSecureExt - Access to the port is denied until the port client is authorized (by 802.1X). psk - Access to the port is denied until the port client is authorized (by 802.1X key negotiation). macAddressAndPsk - The MAC address is first authenticated and only if this succeeds does the psk then attempt user authentication. userLoginSecureExtOrPsk - This selects both the userLoginSecureExt and psk modes together such that either is allowed to authorized access. Which mode works for client depends on the client's choice. ext - Access to the port is denied until the port client is authenticated (by ext).
| ||||
| Chh3cDot11SecurityUserLoginTxKeyType | 1.3.6.1.4.1.25506.2.75.4.6.4.1.2 | INTEGER | RW | |
column · INTEGER · read-write · current This indicates the key type in the 802.1X EAPOL_Key packet. userLoginTxKeyTypeNone - This means the key type is not set yet. userLoginTxKeyTypeDot11Key - This selects the 802.11 key type. userLoginTxKeyTypeRsaRC4Key - This selects the RC4 key for RSA RC4 session encryption.
| ||||
| Chh3cDot11SecurityPskKeyMode | 1.3.6.1.4.1.25506.2.75.4.6.4.1.3 | INTEGER | RW | |
column · INTEGER · read-write · current This is the password input mode. When input as pskKeyModePassPhrase, hh3cDot11SecurePskKeyString must be 8 to 63 characters; when input as pskKeyModeRawKey, hh3cDot11SecurePskKeyString must be 64 characters and each character must be '0'-'9', 'a'-'f' and 'A'-'F'.
| ||||
| Chh3cDot11SecurityPskKeyString | 1.3.6.1.4.1.25506.2.75.4.6.4.1.4 | DisplayString | RW | |
column · DisplayString · read-write · current This is the password string used for psk authentication. | ||||
| Thh3cDot11WlanMeshIfTable | 1.3.6.1.4.1.25506.2.75.4.6.5 | NA | ||
table · not-accessible · current This table is used to configure WLAN mesh interface. | ||||
| Rhh3cDot11WlanMeshIfEntry | 1.3.6.1.4.1.25506.2.75.4.6.5.1 | NA | ||
row · not-accessible · current Each entry contains the WLAN mesh interface configuration. | ||||
| Chh3cDot11WlanMeshIfNumber | 1.3.6.1.4.1.25506.2.75.4.6.5.1.1 | Integer32 | NA | |
column · Integer32 · not-accessible · current This node represents the WLAN mesh interface number. | ||||
| Chh3cDot11WlanMeshIfIndex | 1.3.6.1.4.1.25506.2.75.4.6.5.1.2 | Integer32 | RO | |
column · Integer32 · read-only · current This node represents the index of WLAN mesh interface. | ||||
| Chh3cDot11WlanMeshRowStatus | 1.3.6.1.4.1.25506.2.75.4.6.5.1.3 | RowStatus | RC | |
column · RowStatus · read-create · current This node represents the WLAN mesh interface row status. | ||||
| Nhh3cDot11ACBackupGroup | 1.3.6.1.4.1.25506.2.75.4.7 | |||
| Shh3cDot11BackupACAdrssIP | 1.3.6.1.4.1.25506.2.75.4.7.1 | InetAddress | RW | |
scalar · InetAddress · read-write · current This object represents the backup AC IP address. If the backup AC IP address is not configured, the object value is 0.0.0.0. | ||||
| Shh3cDot11BackupACAdrssIPv6 | 1.3.6.1.4.1.25506.2.75.4.7.2 | InetAddress | RW | |
scalar · InetAddress · read-write · current This object represents the backup AC IPv6 address. If the backup AC IPv6 address is not configured, the object value is 0::0. | ||||
| Nhh3cDot11RadioElementConfigGroup | 1.3.6.1.4.1.25506.2.75.4.8 | |||
| Thh3cDot11nRadioCfgTable | 1.3.6.1.4.1.25506.2.75.4.8.1 | NA | ||
table · not-accessible · current This table is used to configure dot11n on the radio. | ||||
| Rhh3cDot11nRadioCfgEntry | 1.3.6.1.4.1.25506.2.75.4.8.1.1 | NA | ||
row · not-accessible · current This entry contains the dot11n configuration on the radio. | ||||
| Chh3cDot11nRadioCfgIndex | 1.3.6.1.4.1.25506.2.75.4.8.1.1.1 | Hh3cDot11RadioElementIndex | NA | |
column · Hh3cDot11RadioElementIndex · not-accessible · current Represents index of the radio. | ||||
| Chh3cDot11nAMpduEnable | 1.3.6.1.4.1.25506.2.75.4.8.1.1.2 | TruthValue | RW | |
column · TruthValue · read-write · current Enable the function of A-MPDU. | ||||
| Chh3cDot11nAMsduEnable | 1.3.6.1.4.1.25506.2.75.4.8.1.1.3 | TruthValue | RW | |
column · TruthValue · read-write · current Enable the function of A-MSDU. | ||||
| Chh3cDot11nClientDot11nOnly | 1.3.6.1.4.1.25506.2.75.4.8.1.1.4 | TruthValue | RW | |
column · TruthValue · read-write · current If radio type is 802.11an or 802.11gn, only permit clients of 11n mode. If radio type is 802.11ac, permit clients of 11n and 11ac mode. | ||||
| Chh3cDot11nChanelBand | 1.3.6.1.4.1.25506.2.75.4.8.1.1.5 | INTEGER | RW | |
column · INTEGER · read-write · current Specify the bandwidth mode.
| ||||
| Chh3cDot11nShortGiEnable | 1.3.6.1.4.1.25506.2.75.4.8.1.1.6 | TruthValue | RW | |
column · TruthValue · read-write · current The function of Short GI. | ||||
| Chh3cDot11nClientDot11acOnly | 1.3.6.1.4.1.25506.2.75.4.8.1.1.7 | TruthValue | RW | |
column · TruthValue · read-write · current Only permit clients of 11ac mode. | ||||
| Chh3cDot11nSupportMaxMcs | 1.3.6.1.4.1.25506.2.75.4.8.1.1.8 | Integer32 (0..76) | RW | |
column · Integer32 (0..76) · read-write · current Specify the maximum Modulation and Coding Scheme (MCS) index for 802.11n supported rates. The specified maximum MCS index for 802.11n supported rates must be no less than the specified maximum MCS index for 802.11n mandatory rates. | ||||
| Chh3cDot11nMandatoryMaxMcs | 1.3.6.1.4.1.25506.2.75.4.8.1.1.9 | Integer32 (0..76 | 255) | RW | |
column · Integer32 (0..76 | 255) · read-write · current Specify the maximum modulation and coding scheme (MCS) index for 802.11n mandatory rates. The value 255 indicates that no maximum MCS index is specified. No maximum MCS index is specified for 802.11n mandatory rates by default. Besides 255, the specified maximum MCS index for 802.11n supported rates must be no less than the specified maximum MCS index for 802.11n mandatory rates. | ||||
| Thh3cDot11RadioWDSTable | 1.3.6.1.4.1.25506.2.75.4.8.2 | NA | ||
table · not-accessible · current This table is used to configure WDS on the radio. | ||||
| Rhh3cDot11RadioWDSEntry | 1.3.6.1.4.1.25506.2.75.4.8.2.1 | NA | ||
row · not-accessible · current Each entry contains the WDS configuration on the radio. | ||||
| Chh3cDot11RadioWDSIndex | 1.3.6.1.4.1.25506.2.75.4.8.2.1.1 | Hh3cDot11RadioElementIndex | NA | |
column · Hh3cDot11RadioElementIndex · not-accessible · current Represents the element index of radio. | ||||
| Chh3cDot11RadioWDSMode | 1.3.6.1.4.1.25506.2.75.4.8.2.1.2 | INTEGER | RW | |
column · INTEGER · read-write · current Represents enable the WDS mode or not. nowds: The WDS mode is disabled. wds : The WDS mode is enabled
| ||||
| Chh3cDot11RadioWDSNetWorkID | 1.3.6.1.4.1.25506.2.75.4.8.2.1.3 | OCTET STRING (SIZE (0..32)) | RW | |
column · OCTET STRING (SIZE (0..32)) · read-write · current Represents the mesh ID of WDS. | ||||
| Chh3cDot11WDSSecPskKeyMode | 1.3.6.1.4.1.25506.2.75.4.8.2.1.4 | INTEGER | RW | |
column · INTEGER · read-write · current Represents the PSK mode of WDS.
| ||||
| Chh3cDot11WDSSecPskKeyString | 1.3.6.1.4.1.25506.2.75.4.8.2.1.5 | DisplayString | RW | |
column · DisplayString · read-write · current Represents the PSK value of WDS. | ||||
| Thh3cDot11nRadioCfg2Table | 1.3.6.1.4.1.25506.2.75.4.8.3 | NA | ||
table · not-accessible · current This table is used to configure dot11n on the radio. | ||||
| Rhh3cDot11nRadioCfg2Entry | 1.3.6.1.4.1.25506.2.75.4.8.3.1 | NA | ||
row · not-accessible · current This entry contains the dot11n configuration on the radio. | ||||
| Chh3cDot11nRadioCfg2APIDIndex | 1.3.6.1.4.1.25506.2.75.4.8.3.1.1 | Hh3cDot11ObjectIDType | NA | |
column · Hh3cDot11ObjectIDType · not-accessible · current Represents index of the AP. | ||||
| Chh3cDot11nRadioCfg2RadioIDIndex | 1.3.6.1.4.1.25506.2.75.4.8.3.1.2 | Hh3cDot11RadioScopeType | NA | |
column · Hh3cDot11RadioScopeType · not-accessible · current Represents index of the radio. | ||||
| Chh3cDot11nRadioCfg2AMpduEnable | 1.3.6.1.4.1.25506.2.75.4.8.3.1.3 | TruthValue | RW | |
column · TruthValue · read-write · current Enable the function of A-MPDU. | ||||
| Chh3cDot11nRadioCfg2AMsduEnable | 1.3.6.1.4.1.25506.2.75.4.8.3.1.4 | TruthValue | RW | |
column · TruthValue · read-write · current Enable the function of A-MSDU. | ||||
| Chh3cDot11nRadioCfg2ClientDot11nOnly | 1.3.6.1.4.1.25506.2.75.4.8.3.1.5 | TruthValue | RW | |
column · TruthValue · read-write · current If radio type is 802.11an or 802.11gn, only permit clients of 11n mode. If radio type is 802.11ac, permit clients of 11n and 11ac mode. | ||||
| Chh3cDot11nRadioCfg2ChannelBand | 1.3.6.1.4.1.25506.2.75.4.8.3.1.6 | INTEGER | RW | |
column · INTEGER · read-write · current Specify the bandwidth mode.
| ||||
| Chh3cDot11nRadioCfg2ShortGiEnable | 1.3.6.1.4.1.25506.2.75.4.8.3.1.7 | TruthValue | RW | |
column · TruthValue · read-write · current Enable the function of Short GI. | ||||
| Chh3cDot11nRadioCfg2AMpduEnableCM | 1.3.6.1.4.1.25506.2.75.4.8.3.1.8 | INTEGER | RW | |
column · INTEGER · read-write · current Enable the function of A-MPDU.
| ||||
| Chh3cDot11nRadioCfg2ChannelBandCM | 1.3.6.1.4.1.25506.2.75.4.8.3.1.9 | INTEGER | RW | |
column · INTEGER · read-write · current Specify the bandwidth mode.
| ||||
| Chh3cDot11nRadioCfg2ShortGiEnableCM | 1.3.6.1.4.1.25506.2.75.4.8.3.1.10 | INTEGER | RW | |
column · INTEGER · read-write · current Enable the function of Short GI.
| ||||
| Chh3cDot11nRadioCfg2ClientDot11acOnly | 1.3.6.1.4.1.25506.2.75.4.8.3.1.11 | TruthValue | RW | |
column · TruthValue · read-write · current Only permit clients of 11ac mode. | ||||
| Chh3cDot11nRadioCfg2ClientDot11nOnlyCM | 1.3.6.1.4.1.25506.2.75.4.8.3.1.12 | Hh3cDot11TruthValueCM | RW | |
column · Hh3cDot11TruthValueCM · read-write · current If radio type is 802.11an or 802.11gn, permit only clients of 11n mode. If radio type is 802.11ac, permit clients of both 11n and 11ac mode. | ||||
| Chh3cDot11nRadioCfg2SupportMaxMcs | 1.3.6.1.4.1.25506.2.75.4.8.3.1.13 | Integer32 (0..76) | RW | |
column · Integer32 (0..76) · read-write · current Specify the maximum Modulation and Coding Scheme (MCS) index for 802.11n supported rates. The specified maximum MCS index for 802.11n supported rates must be no less than the specified maximum MCS index for 802.11n mandatory rates. | ||||
| Chh3cDot11nRadioCfg2MandatoryMaxMcs | 1.3.6.1.4.1.25506.2.75.4.8.3.1.14 | Integer32 (0..76 | 255) | RW | |
column · Integer32 (0..76 | 255) · read-write · current Specify the maximum modulation and coding scheme (MCS) index for 802.11n mandatory rates. The value 255 indicates that no maximum MCS index is specified. No maximum MCS index is specified for 802.11n mandatory rates by default. Besides 255, the specified maximum MCS index for 802.11n supported rates must be no less than the specified maximum MCS index for 802.11n mandatory rates. | ||||
| Nhh3cDot11CfgNotifyGroup | 1.3.6.1.4.1.25506.2.75.4.9 | |||
| Nhh3cDot11CfgNotifications | 1.3.6.1.4.1.25506.2.75.4.9.0 | |||
| !hh3cDot11CfgCipherChange | 1.3.6.1.4.1.25506.2.75.4.9.0.1 | |||
notification · current This notification is sent when cipher type of corresponding service template is changed. | ||||
| !hh3cDot11CfgPSKChange | 1.3.6.1.4.1.25506.2.75.4.9.0.2 | |||
notification · current This notification is sent when pre-shared key of corresponding service template is changed.
| ||||
| !hh3cDot11SSIDWepIDConflictTrap | 1.3.6.1.4.1.25506.2.75.4.9.0.3 | |||
notification · current This notification will be sent when the same wep ID is configured on two service policies. | ||||
| Nhh3cDot11CfgTrapVarObjects | 1.3.6.1.4.1.25506.2.75.4.9.1 | |||
| Shh3cDot11PreConflictTemplateNum | 1.3.6.1.4.1.25506.2.75.4.9.1.1 | Integer32 (1..1024) | AN | |
scalar · Integer32 (1..1024) · accessible-for-notify · current Represents previous service policy ID when radio bind service policy and current service policy conflict with previous service policy in cipher configuration. | ||||
| Shh3cDot11CurrConflictTemplateNum | 1.3.6.1.4.1.25506.2.75.4.9.1.2 | Integer32 (1..1024) | AN | |
scalar · Integer32 (1..1024) · accessible-for-notify · current Represents current service policy ID when radio bind service policy and current service policy conflict with previous service policy in cipher configuration. | ||||
| Shh3cDot11ConflictCipherIdx | 1.3.6.1.4.1.25506.2.75.4.9.1.3 | Integer32 (1..4) | AN | |
scalar · Integer32 (1..4) · accessible-for-notify · current Represents wep ID that conflicted with. | ||||
| Shh3cDot11ConfigureAPID | 1.3.6.1.4.1.25506.2.75.4.9.1.4 | Hh3cDot11ObjectIDType | AN | |
scalar · Hh3cDot11ObjectIDType · accessible-for-notify · current Represents which AP is configured. | ||||
| Shh3cDot11ConfigureRadioID | 1.3.6.1.4.1.25506.2.75.4.9.1.5 | Hh3cDot11RadioScopeType | AN | |
scalar · Hh3cDot11RadioScopeType · accessible-for-notify · current Represents which radio in AP is configured. | ||||
| Shh3cDot11ConfigureAPMacAddress | 1.3.6.1.4.1.25506.2.75.4.9.1.6 | MacAddress | AN | |
scalar · MacAddress · accessible-for-notify · current Represents MAC Address of AP. | ||||
| Shh3cDot11PreConflictTemplateSSID | 1.3.6.1.4.1.25506.2.75.4.9.1.7 | Hh3cDot11SSIDStringType | AN | |
scalar · Hh3cDot11SSIDStringType · accessible-for-notify · current Represents the previous SSID of the AP. | ||||
| Shh3cDot11CurrConflictTemplateSSID | 1.3.6.1.4.1.25506.2.75.4.9.1.8 | Hh3cDot11SSIDStringType | AN | |
scalar · Hh3cDot11SSIDStringType · accessible-for-notify · current Represents the current SSID of the AP. | ||||
| Nhh3cDot11LocalACConfigGroup | 1.3.6.1.4.1.25506.2.75.4.10 | |||
| Thh3cDot11LocalACTemplateTable | 1.3.6.1.4.1.25506.2.75.4.10.1 | NA | ||
table · not-accessible · current By local AC template CLI, administrator will configure the parameters of LocalAC by convenience. Before local AC boot up and connect to AC by CAPWAP tunnel, administrator will create local AC template for each local AC. When local AC connect to AC, AC will assign configuration to local AC by hh3cDot11LocalACSerialID information in local AC template. | ||||
| Rhh3cDot11LocalACTemplateEntry | 1.3.6.1.4.1.25506.2.75.4.10.1.1 | NA | ||
row · not-accessible · current Each entry contains configuration information for each LocalAC. | ||||
| Chh3cDot11LocalACTemplateName | 1.3.6.1.4.1.25506.2.75.4.10.1.1.1 | OCTET STRING (SIZE (0..127)) | NA | |
column · OCTET STRING (SIZE (0..127)) · not-accessible · current Represents the name of LocalAC template. | ||||
| Chh3cDot11LocalACName | 1.3.6.1.4.1.25506.2.75.4.10.1.1.2 | OCTET STRING | RC | |
column · OCTET STRING · read-create · current Represents the LocalAC name. | ||||
| Chh3cDot11LocalACSerialID | 1.3.6.1.4.1.25506.2.75.4.10.1.1.3 | OCTET STRING | RC | |
column · OCTET STRING · read-create · current Represents LocalAC serial id. | ||||
| Chh3cDot11TemLocalACModelAlias | 1.3.6.1.4.1.25506.2.75.4.10.1.1.4 | OCTET STRING | RC | |
column · OCTET STRING · read-create · current Represents the alias of LocalAC model name. | ||||
| Chh3cDot11LocalACTempRowStatus | 1.3.6.1.4.1.25506.2.75.4.10.1.1.5 | RowStatus | RC | |
column · RowStatus · read-create · current The status of this table entry. | ||||
| Chh3cDot11LocalACStatus | 1.3.6.1.4.1.25506.2.75.4.10.1.1.6 | INTEGER | RO | |
column · INTEGER · read-only · current Represents the capwap status of local AC. The following values are supported: join - local AC is joining to cnetral AC. joinConfirm - cnetral AC confirm whether permit local AC to - join. download - local AC is downloading software from cnetral - AC. config - local AC and cnetral AC exchange configuration - before local AC provide WLAN service. run - The local AC is run. idle - The local AC is idle.
| ||||
| Chh3cDot11LocalACIPAddress | 1.3.6.1.4.1.25506.2.75.4.10.1.1.7 | IpAddress | RO | |
column · IpAddress · read-only · current Represents the IP address of an LocalAC. | ||||
| Chh3cDot11LocalACIPv6Address | 1.3.6.1.4.1.25506.2.75.4.10.1.1.8 | OCTET STRING | RO | |
column · OCTET STRING · read-only · current Represents the IPv6 address of LocalAC. | ||||
| Chh3cDot11EchoInterval | 1.3.6.1.4.1.25506.2.75.4.10.1.1.9 | Integer32 (0 | 5..255) | RC | |
column · Integer32 (0 | 5..255) · read-create · current Represents the interval of echo.
| ||||
| Chh3cDot11RetransInterval | 1.3.6.1.4.1.25506.2.75.4.10.1.1.10 | Integer32 (3..8) | RC | |
column · Integer32 (3..8) · read-create · current Represents the interval of retransmit.
| ||||
| Chh3cDot11RetransCount | 1.3.6.1.4.1.25506.2.75.4.10.1.1.11 | Integer32 (2..5) | RC | |
column · Integer32 (2..5) · read-create · current Represents the maximum of retransmit.
| ||||
| Chh3cDot11FirmwareUpgrade | 1.3.6.1.4.1.25506.2.75.4.10.1.1.12 | INTEGER | RC | |
column · INTEGER · read-create · current Represents the status of firmware upgrade for an local AC. The following values are supported: enable - local AC firmware upgrade will be enabled. disable - local AC firmware upgrade will be disabled.
| ||||
| Nhh3cDot11RemoteConfigGroup | 1.3.6.1.4.1.25506.2.75.4.11 | |||
| Thh3cDot11RemoteCfgApTable | 1.3.6.1.4.1.25506.2.75.4.11.1 | NA | ||
table · not-accessible · current Remote configuration for an AP. | ||||
| Rhh3cDot11RemoteCfgApEntry | 1.3.6.1.4.1.25506.2.75.4.11.1.1 | NA | ||
row · not-accessible · current Each entry contains configuration information for each AP.
| ||||
| Chh3cDot11RmtApName | 1.3.6.1.4.1.25506.2.75.4.11.1.1.1 | OCTET STRING (SIZE (1..127)) | NA | |
column · OCTET STRING (SIZE (1..127)) · not-accessible · current Represents the name of an AP. | ||||
| Chh3cDot11RmtVlanList | 1.3.6.1.4.1.25506.2.75.4.11.1.1.2 | OCTET STRING | RW | |
column · OCTET STRING · read-write · current Represents the VLAN list on an AP. | ||||
| Chh3cDot11RmtCfgEnable | 1.3.6.1.4.1.25506.2.75.4.11.1.1.3 | TruthValue | RW | |
column · TruthValue · read-write · current Enables remote configuration synchronization. | ||||
| Thh3cDot11RemoteCfgIFTable | 1.3.6.1.4.1.25506.2.75.4.11.2 | NA | ||
table · not-accessible · current Remote configuration for interface on an AP. | ||||
| Rhh3cDot11RemoteCfgIFEntry | 1.3.6.1.4.1.25506.2.75.4.11.2.1 | NA | ||
row · not-accessible · current Each entry contains configuration information for each interface on an AP. | ||||
| Chh3cDot11RmtIfApName | 1.3.6.1.4.1.25506.2.75.4.11.2.1.1 | OCTET STRING (SIZE (1..127)) | NA | |
column · OCTET STRING (SIZE (1..127)) · not-accessible · current Represents the name of an AP. | ||||
| Chh3cDot11RmtIfType | 1.3.6.1.4.1.25506.2.75.4.11.2.1.2 | Integer32 | NA | |
column · Integer32 · not-accessible · current Represents the type of the interface. ethernet (1), gigabitethernet (2), ten-gigabitethernet (3), smartrate-ethernet(4). | ||||
| Chh3cDot11RmtIfNum | 1.3.6.1.4.1.25506.2.75.4.11.2.1.3 | Integer32 | NA | |
column · Integer32 · not-accessible · current Represents the ID of the interface. | ||||
| Chh3cDot11RmtIfName | 1.3.6.1.4.1.25506.2.75.4.11.2.1.4 | OCTET STRING | RO | |
column · OCTET STRING · read-only · current Represents the name of the interface. | ||||
| Chh3cDot11RmtIfLinkType | 1.3.6.1.4.1.25506.2.75.4.11.2.1.5 | INTEGER | RW | |
column · INTEGER · read-write · current Set the link type to access, hybrid or trunk. Setting recommend one and setup more related nodes.
| ||||
| Chh3cDot11RmtIfAccessVlan | 1.3.6.1.4.1.25506.2.75.4.11.2.1.6 | Integer32 | RW | |
column · Integer32 · read-write · current Specify the access VLAN for a port. | ||||
| Chh3cDot11RmtIfTrunkPvidVlan | 1.3.6.1.4.1.25506.2.75.4.11.2.1.7 | Integer32 | RW | |
column · Integer32 · read-write · current Specify the default VLAN for a port. | ||||
| Chh3cDot11RmtIfTrunkVlanlist | 1.3.6.1.4.1.25506.2.75.4.11.2.1.8 | OCTET STRING | RW | |
column · OCTET STRING · read-write · current Specify the permitted VLAN list for a port. | ||||
| Chh3cDot11RmtIfHybridPvidVlan | 1.3.6.1.4.1.25506.2.75.4.11.2.1.9 | Integer32 | RW | |
column · Integer32 · read-write · current Specify the default VLAN for the hybrid port. | ||||
| Chh3cDot11RmtIfHybVlanListTag | 1.3.6.1.4.1.25506.2.75.4.11.2.1.10 | OCTET STRING | RW | |
column · OCTET STRING · read-write · current Assign the hybrid port to tagged VLANs. | ||||
| Chh3cDot11RmtIfHybVlanListUnTag | 1.3.6.1.4.1.25506.2.75.4.11.2.1.11 | OCTET STRING | RW | |
column · OCTET STRING · read-write · current Assign the hybrid port to untagged VLANs. | ||||
| Chh3cDot11RmtIfIsolate | 1.3.6.1.4.1.25506.2.75.4.11.2.1.12 | TruthValue | RW | |
column · TruthValue · read-write · current Enable or disable port isolation. | ||||
| Chh3cDot11RmtIfLinkAggGroupId | 1.3.6.1.4.1.25506.2.75.4.11.2.1.13 | Integer32 | RW | |
column · Integer32 · read-write · current Specify link aggregation group number for the port. | ||||
| Chh3cDot11RmtIfManagement | 1.3.6.1.4.1.25506.2.75.4.11.2.1.14 | TruthValue | RW | |
column · TruthValue · read-write · current Interface management of the port. | ||||
Traps / Notifications
- hh3cDot11CfgCipherChange
1.3.6.1.4.1.25506.2.75.4.9.0.1 - hh3cDot11CfgPSKChange
1.3.6.1.4.1.25506.2.75.4.9.0.2 - hh3cDot11SSIDWepIDConflictTrap
1.3.6.1.4.1.25506.2.75.4.9.0.3