COMTROL-ES8510-MIB
Pepperl+Fuchs ComtrolComtrol Corporation 100 Fifth Avenue NW New Brighton, MN 55112 TEL: +1.763.957.6000 E-mail: [email protected]
snmptranslate -m COMTROL-ES8510-MIB -Tpsnmpwalk -v2c -c <community> -m COMTROL-ES8510-MIB <host> 1.3.6.1.4.1.2882.1Imports
| Q-BRIDGE-MIB | PortList |
|---|---|
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP |
| SNMPv2-SMI | Bits, Integer32, IpAddress, MODULE-IDENTITY, MibIdentifier, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, internet, iso |
| SNMPv2-TC | DisplayString, MacAddress, PhysAddress, RowStatus, TEXTUAL-CONVENTION, TimeInterval |
OID tree
| Name | OID | Type | Access | Status |
|---|---|---|---|---|
| Nprivate | 1.3.6.1.4 | |||
| Nenterprises | 1.3.6.1.4.1 | |||
| Ncomtrol | 1.3.6.1.4.1.2882 | |||
| Icontact | 1.3.6.1.4.1.2882.1 | |||
identity Comtrol Corporation 100 Fifth Avenue NW New Brighton, MN 55112 TEL: +1.763.957.6000 E-mail: [email protected] | ||||
| Nproducts | 1.3.6.1.4.1.2882.2 | |||
| NmanagedSwitch | 1.3.6.1.4.1.2882.2.1 | |||
| Nes8510 | 1.3.6.1.4.1.2882.2.1.1 | |||
| NsystemInfo | 1.3.6.1.4.1.2882.2.1.1.1 | |||
| SsystemName | 1.3.6.1.4.1.2882.2.1.1.1.1 | DisplayString (SIZE (0..255)) | RO | |
scalar · DisplayString (SIZE (0..255)) · read-only · current An administratively-assigned name for this managed node. By convention, this is the node's fully-qualified domain name. | ||||
| SsystemLocation | 1.3.6.1.4.1.2882.2.1.1.1.2 | DisplayString (SIZE (0..255)) | RO | |
scalar · DisplayString (SIZE (0..255)) · read-only · current The physical location of this node (e.g., telephone closet, 3rd floor'). | ||||
| SsystemContact | 1.3.6.1.4.1.2882.2.1.1.1.3 | DisplayString (SIZE (0..255)) | RO | |
scalar · DisplayString (SIZE (0..255)) · read-only · current The textual identification of the contact person for this managed node, together with information on how to contact this person. | ||||
| SsystemDescr | 1.3.6.1.4.1.2882.2.1.1.1.4 | DisplayString (SIZE (0..255)) | RO | |
scalar · DisplayString (SIZE (0..255)) · read-only · current A textual description of the entity. This value should include the full name and version identification of the system's hardware type, software operating-system, and networking software. It is mandatory that this only contain printable ASCII characters. | ||||
| SsystemFwVer | 1.3.6.1.4.1.2882.2.1.1.1.5 | DisplayString (SIZE (0..20)) | RO | |
scalar · DisplayString (SIZE (0..20)) · read-only · current Firmware version of the device. | ||||
| SsystemMacAddress | 1.3.6.1.4.1.2882.2.1.1.1.6 | MacAddress | RO | |
scalar · MacAddress · read-only · current The MAC address of this device. An Media Access Control address (MAC address) is a unique identifier attached to most network adapters (NICs). It is a number that acts like a name for a particular network adapter | ||||
| NbasicSetting | 1.3.6.1.4.1.2882.2.1.1.2 | |||
| NswitchSetting | 1.3.6.1.4.1.2882.2.1.1.2.1 | |||
| SswitchSettingSystemName | 1.3.6.1.4.1.2882.2.1.1.2.1.1 | DisplayString (SIZE (1..256)) | RW | |
scalar · DisplayString (SIZE (1..256)) · read-write · current An administratively-assigned name for this managed node. By convention, this is the node's fully-qualified domain name. | ||||
| SswitchSettingSystemLocation | 1.3.6.1.4.1.2882.2.1.1.2.1.2 | DisplayString (SIZE (0..256)) | RW | |
scalar · DisplayString (SIZE (0..256)) · read-write · current The physical location of this node (e.g., telephone closet, 3rd floor'). | ||||
| SswitchSettingSystemContact | 1.3.6.1.4.1.2882.2.1.1.2.1.3 | DisplayString (SIZE (0..256)) | RW | |
scalar · DisplayString (SIZE (0..256)) · read-write · current The textual identification of the contact person for this managed node, together with information on how to contact this person. | ||||
| NadminPassword | 1.3.6.1.4.1.2882.2.1.1.2.2 | |||
| SadminPasswordUserName | 1.3.6.1.4.1.2882.2.1.1.2.2.1 | DisplayString (SIZE (0..20)) | RW | |
scalar · DisplayString (SIZE (0..20)) · read-write · current The name(ID) of security manager. | ||||
| SadminPasswordPassword | 1.3.6.1.4.1.2882.2.1.1.2.2.2 | DisplayString (SIZE (0..8)) | WO | |
scalar · DisplayString (SIZE (0..8)) · write-only · current The password of security manager. This object can't be read. it's write-only. | ||||
| NipConfiguration | 1.3.6.1.4.1.2882.2.1.1.2.3 | |||
| TipConfigurationTable | 1.3.6.1.4.1.2882.2.1.1.2.3.1 | NA | ||
table · not-accessible · current Table of descriptive information and configuration about the IP of the device. | ||||
| RipConfigurationEntry | 1.3.6.1.4.1.2882.2.1.1.2.3.1.1 | NA | ||
row · not-accessible · current Information configuring static IP or DHCP configuration of the device.
| ||||
| CipConfigurationIndex | 1.3.6.1.4.1.2882.2.1.1.2.3.1.1.1 | INTEGER | NA | |
column · INTEGER · not-accessible · current This object identifies IP configuration entries. | ||||
| CipConfigurationDHCPStatus | 1.3.6.1.4.1.2882.2.1.1.2.3.1.1.2 | INTEGER | RW | |
column · INTEGER · read-write · current Parameter configuring DHCP client functionality of the device. When enabled, device will be a DHCP client and request for the IP configuration from DHCP server. The Dynamic Host Configuration Protocol (DHCP) automates the assignment of IP addresses, subnet masks, default routers, and other IP parameters. The assignment usually occurs when the DHCP-configured machine boots up or regains connectivity to the network. The DHCP client sends out a query requesting a response from a DHCP server on the locally attached network. The query is typically initiated immediately after booting up and before the client initiates any IP based communication with other hosts. The DHCP server then replies to the client with its assigned IP address, subnet mask, DNS server and default gateway information. Note: Other items in this table will not be modified, when ipConfigurationDHCPStatus is enabled.
| ||||
| CipConfigurationAddress | 1.3.6.1.4.1.2882.2.1.1.2.3.1.1.3 | IpAddress | RW | |
column · IpAddress · read-write · current The IP address of switch. An IP address (Internet Protocol address) is a unique address that devices use in order to identify and communicate with each other on a computer network utilizing the Internet Protocol standard (IP). Any participating network device can has its own unique address. | ||||
| CipConfigurationSubMask | 1.3.6.1.4.1.2882.2.1.1.2.3.1.1.4 | IpAddress | RW | |
column · IpAddress · read-write · current The subnet mask is a 32-bit number in the same format and representation as IP addresses. The subnet mask determines which bits in the IP address are interpreted as the network number, which as the subnetwork number, and which as the host number. Each IP address bit that corresponds to a 1 in the subnet mask is in the network/subnetwork part of the address. This group of numbers is also called the Network ID. Each IP address bit that corresponds to a 0 is in the host part of the IP address. | ||||
| CipConfigurationGateway | 1.3.6.1.4.1.2882.2.1.1.2.3.1.1.5 | IpAddress | RW | |
column · IpAddress · read-write · current The default gateway IP address identifies the gateway (for example, a router) that receives and forwards those packets whose addresses are unknown to the local network. The agent uses the default gateway address when sending alert packets to the management workstation on a network other than the local network. | ||||
| CipConfigurationDNS1 | 1.3.6.1.4.1.2882.2.1.1.2.3.1.1.6 | IpAddress | RW | |
column · IpAddress · read-write · current Parameter configuring the first DNS server of the device. The domain name system (DNS) stores and associates many types of information with domain names. Most importantly, it translates domain names (computer hostnames) to IP addresses, which makes it possible to attach easy-to-remember domain names to hard-to-remember IP addresses (such as 100.50.10.100). | ||||
| CipConfigurationDNS2 | 1.3.6.1.4.1.2882.2.1.1.2.3.1.1.7 | IpAddress | RW | |
column · IpAddress · read-write · current Parameter configuring the second DNS server of the device. | ||||
| CipConfigurationStatus | 1.3.6.1.4.1.2882.2.1.1.2.3.1.1.8 | RowStatus | RC | |
column · RowStatus · read-create · current The status of the IP configuration entry. Only one configuration entry is supported on the device. Set active(1) to activate the parameters of the entry on the device. | ||||
| NtimeSetting | 1.3.6.1.4.1.2882.2.1.1.2.4 | |||
| SsystemTime | 1.3.6.1.4.1.2882.2.1.1.2.4.1 | DisplayString | RO | |
scalar · DisplayString · read-only · current current system time in format yyyy.mm.dd-hh:mm:ss | ||||
| SutcTimeZone | 1.3.6.1.4.1.2882.2.1.1.2.4.2 | INTEGER | RW | |
scalar · INTEGER · read-write · current UTC Timezone list.
(GMT-12:00) Eniwetok, Kwajalein
(GMT-11:00) Midway Island, Samoa
(GMT-10:00) Hawaii
(GMT-09:00) Alaska
(GMT-08:00) Pacific Time (US & Canada), Tijuana
(GMT-07:00) Arizona
(GMT-07:00) Mountain Time (US & Canada)
(GMT-06:00) Central America
(GMT-06:00) Central Time (US & Canada)
(GMT-06:00) Mexico City
(GMT-06:00) Saskatchewan
(GMT-05:00) Bogota, Lima, Quito
(GMT-05:00) Eastern Time (US & Canada)
(GMT-05:00) Indiana (East)
(GMT-04:00) Atlantic Time (Canada)
(GMT-04:00) Caracas, La Paz
(GMT-04:00) Santiago
(GMT-03:00) NewFoundland
(GMT-03:00) Brasilia
(GMT-03:00) Buenos Aires, Georgetown
(GMT-03:00) Greenland
(GMT-02:00) Mid-Atlantic
(GMT-01:00) Azores
(GMT-01:00) Cape Verde Is.
(GMT) Casablanca, Monrovia
(GMT) Greenwich Mean Time: Dublin, Edinburgh, Lisbon, London
(GMT+01:00) Amsterdam, Berlin, Bern, Rome, Stockholm, Vienna
(GMT+01:00) Belgrade, Bratislava, Budapest, Ljubljana, Prague
(GMT+01:00) Brussels, Copenhagen, Madrid, Paris
(GMT+01:00) Sarajevo, Skopje, Sofija, Vilnius, Warsaw, Zagreb
(GMT+01:00) West Central Africa
(GMT+02:00) Athens, Istanbul, Minsk
(GMT+02:00) Bucharest
(GMT+02:00) Cairo
(GMT+02:00) Harare, Pretoria
(GMT+02:00) Helsinki, Riga, Tallinn
(GMT+02:00) Jerusalem
(GMT+03:00) Baghdad
(GMT+03:00) Kuwait, Riyadh
(GMT+03:00) Moscow, St. Petersburg, Volgograd
(GMT+03:00) Nairobi
(GMT+03:30) Tehran
(GMT+04:00) Abu Dhabi, Muscat
(GMT+04:00) Baku, Tbilisi, Yerevan
(GMT+04:30) Kabul
(GMT+05:00) Ekaterinburg
(GMT+05:00) Islamabad, Karachi, Tashkent
(GMT+05:30) Calcutta, Chennai, Mumbai, New Delhi
(GMT+05:45) Kathmandu
(GMT+06:00) Almaty, Novosibirsk
(GMT+06:00) Astana, Dhaka
(GMT+06:00) Sri Jayawardenepura
(GMT+06:30) Rangoon
(GMT+07:00) Bangkok, Hanoi, Jakarta
(GMT+07:00) Krasnoyarsk
(GMT+08:00) Beijing, Chongqing, Hong Kong, Urumqi
(GMT+08:00) Irkutsk, Ulaan Bataar
(GMT+08:00) Kuala Lumpur, Singapore
(GMT+08:00) Perth
(GMT+08:00) Taipei
(GMT+09:00) Osaka, Sapporo, Tokyo
(GMT+09:00) Seoul
(GMT+09:00) Yakutsk
(GMT+09:30) Adelaide
(GMT+09:30) Darwin
(GMT+10:00) Brisbane
(GMT+10:00) Canberra, Melbourne, Sydney
(GMT+10:00) Guam, Port Moresby
(GMT+10:00) Hobart
(GMT+10:00) Vladivostok
(GMT+11:00) Magadan, Solomon Is., New Caledonia
(GMT+12:00) Aukland, Wellington
(GMT+12:00) Fiji, Kamchatka, Marshall Is.
(GMT+13:00) Nuku'alofa
| ||||
| NdayLightSavingTime | 1.3.6.1.4.1.2882.2.1.1.2.4.3 | |||
| SdaylightSavingTimeStart | 1.3.6.1.4.1.2882.2.1.1.2.4.3.1 | DisplayString (SIZE (0..12)) | RW | |
scalar · DisplayString (SIZE (0..12)) · read-write · current The start-time of daylight saveing period, in format mm.n.d/hh:mm m is month, valid range 1-12 (1=January, 2=February, ..., 12=December). n is week of the month (1 to 5, 5 means the last week). d is weekday, valid range 0-6 (0=Sunday, 1=Monday, ..., 6=Saturday). hh:mm is time. | ||||
| SdaylightSavingTimeEnd | 1.3.6.1.4.1.2882.2.1.1.2.4.3.2 | DisplayString (SIZE (0..12)) | RW | |
scalar · DisplayString (SIZE (0..12)) · read-write · current The end-time of daylight saveing period, in format mm.n.d/hh:mm m is month, valid range 1-12 (1=January, 2=February, ..., 12=December). n is week of the month (1 to 5, 5 means the last week). d is weekday, valid range 0-6 (0=Sunday, 1=Monday, ..., 6=Saturday). hh:mm is time. | ||||
| SdaylightSavingOffset | 1.3.6.1.4.1.2882.2.1.1.2.4.3.3 | Integer32 | RW | |
scalar · Integer32 · read-write · current Daylight Saving Offset(Usually is 60 mins). When Enable and current time at Daylight Saving Period, the current time of the switch will be offseted by Daylight Saving Offset. | ||||
| SdaylightSavingTimeStatus | 1.3.6.1.4.1.2882.2.1.1.2.4.3.4 | INTEGER | RW | |
scalar · INTEGER · read-write · current (1)Enable Daylight Saving Time. (2)Disable Daylight Saving Time. Daylight Saving Time: Use this OID to Enable/Disable Daylight Saving Time.
| ||||
| NclockSource | 1.3.6.1.4.1.2882.2.1.1.2.4.4 | |||
| SclockSourceSelection | 1.3.6.1.4.1.2882.2.1.1.2.4.4.1 | INTEGER | RW | |
scalar · INTEGER · read-write · current .
| ||||
| NclockSourceManual | 1.3.6.1.4.1.2882.2.1.1.2.4.4.2 | |||
| SclockSourceManualSetting | 1.3.6.1.4.1.2882.2.1.1.2.4.4.2.1 | DisplayString (SIZE (0..19)) | RW | |
scalar · DisplayString (SIZE (0..19)) · read-write · current set system time, in format yyyy.mm.dd-hh:mm:ss | ||||
| NclockSourceNtp | 1.3.6.1.4.1.2882.2.1.1.2.4.4.3 | |||
| TntpTable | 1.3.6.1.4.1.2882.2.1.1.2.4.4.3.1 | NA | ||
table · not-accessible · current Table of descriptive information and configuration about NTP servers. NTP (Network Time Protocol) synchronizes timekeeping among a set of distributed time servers and clients. This synchronization allows events to be correlated when system logs are created and other time-specific events occur. An NTP server is configured to synchronize NTP clients. Servers can be configured to synchronize any client or only specific clients. NTP servers, however, will accept no synchronization information from their clients and therefore will not let clients update or affect the server's time settings. This switch acts as an NTP client, which tries to let its clock be set and synchronized by an external NTP timeserver. It can be configured to use multiple servers (upto 4 servers). | ||||
| RntpEntry | 1.3.6.1.4.1.2882.2.1.1.2.4.4.3.1.1 | NA | ||
| CntpIndex | 1.3.6.1.4.1.2882.2.1.1.2.4.4.3.1.1.1 | Integer32 | NA | |
column · Integer32 · not-accessible · current This object identifies the entry. | ||||
| CntpServerIP | 1.3.6.1.4.1.2882.2.1.1.2.4.4.3.1.1.2 | IpAddress | RW | |
column · IpAddress · read-write · current The IP address of an NTP Server. Set 0.0.0.0 or 255.255.255.255 to remove this config. | ||||
| NdhcpServer | 1.3.6.1.4.1.2882.2.1.1.2.5 | |||
| SdhcpServerEnable | 1.3.6.1.4.1.2882.2.1.1.2.5.1 | INTEGER | RW | |
scalar · INTEGER · read-write · current Enable or disable dhcp server function.
| ||||
| TdhcpServerPoolTable | 1.3.6.1.4.1.2882.2.1.1.2.5.2 | NA | ||
table · not-accessible · current Table of descriptive information and configuration about DHCP server of the switch. | ||||
| RdhcpServerPoolEntry | 1.3.6.1.4.1.2882.2.1.1.2.5.2.1 | NA | ||
row · not-accessible · current An entry containing DHCP server information of the switch.
| ||||
| CdhcpServerPoolIndex | 1.3.6.1.4.1.2882.2.1.1.2.5.2.1.1 | Integer32 | NA | |
column · Integer32 · not-accessible · current The index of the Address Pool. | ||||
| CdhcpServerPoolName | 1.3.6.1.4.1.2882.2.1.1.2.5.2.1.2 | DisplayString (SIZE (1..20)) | RO | |
column · DisplayString (SIZE (1..20)) · read-only · current The address pool name. | ||||
| CdhcpServerPoolNetwork | 1.3.6.1.4.1.2882.2.1.1.2.5.2.1.3 | IpAddress | RW | |
column · IpAddress · read-write · current The Subnet of the IP Address Pool. | ||||
| CdhcpServerPoolSubMask | 1.3.6.1.4.1.2882.2.1.1.2.5.2.1.4 | IpAddress | RW | |
column · IpAddress · read-write · current The subnet mask of the IP Address Pool. | ||||
| CdhcpServerPoolGateway | 1.3.6.1.4.1.2882.2.1.1.2.5.2.1.5 | IpAddress | RW | |
column · IpAddress · read-write · current The gateway address of the IP Address Pool. | ||||
| CdhcpServerPoolLeaseTime | 1.3.6.1.4.1.2882.2.1.1.2.5.2.1.6 | Integer32 | RW | |
column · Integer32 · read-write · current The lease time(in second) of the Address Pool. | ||||
| CdhcpServerPoolStatus | 1.3.6.1.4.1.2882.2.1.1.2.5.2.1.7 | RowStatus | RC | |
column · RowStatus · read-create · current The status of the Address Pool. | ||||
| TdhcpExcludedTable | 1.3.6.1.4.1.2882.2.1.1.2.5.3 | NA | ||
table · not-accessible · current Table of descriptive information and configuration about DHCP server of the switch. | ||||
| RdhcpExcludedEntry | 1.3.6.1.4.1.2882.2.1.1.2.5.3.1 | NA | ||
row · not-accessible · current An entry containing DHCP server information of the switch. | ||||
| CdhcpExcludedIndex | 1.3.6.1.4.1.2882.2.1.1.2.5.3.1.1 | Integer32 | NA | |
column · Integer32 · not-accessible · current The index of the Excluded Table. | ||||
| CdhcpExcludedIp | 1.3.6.1.4.1.2882.2.1.1.2.5.3.1.2 | IpAddress | RW | |
column · IpAddress · read-write · current The IP address . | ||||
| CdhcpExcludedStatus | 1.3.6.1.4.1.2882.2.1.1.2.5.3.1.3 | RowStatus | RC | |
column · RowStatus · read-create · current The status of a address pool. | ||||
| TdhcpManualBindingTable | 1.3.6.1.4.1.2882.2.1.1.2.5.4 | NA | ||
table · not-accessible · current Table of descriptive information and configuration about DHCP server of the switch. | ||||
| RdhcpManualBindingEntry | 1.3.6.1.4.1.2882.2.1.1.2.5.4.1 | NA | ||
row · not-accessible · current An entry containing DHCP server information of the switch. | ||||
| CdhcpManualBindingIndex | 1.3.6.1.4.1.2882.2.1.1.2.5.4.1.1 | Integer32 | NA | |
column · Integer32 · not-accessible · current The index of the Static Binding Table. | ||||
| CdhcpManualBindingIp | 1.3.6.1.4.1.2882.2.1.1.2.5.4.1.2 | IpAddress | RW | |
column · IpAddress · read-write · current The IP address. | ||||
| CdhcpManualBindingMac | 1.3.6.1.4.1.2882.2.1.1.2.5.4.1.3 | MacAddress | RW | |
column · MacAddress · read-write · current The MAC address. | ||||
| CdhcpManualBindingStatus | 1.3.6.1.4.1.2882.2.1.1.2.5.4.1.4 | RowStatus | RC | |
column · RowStatus · read-create · current The status of the binding. | ||||
| TdhcpStaticPortTable | 1.3.6.1.4.1.2882.2.1.1.2.5.5 | NA | ||
table · not-accessible · current Table of descriptive information and configuration about DHCP server of the switch. | ||||
| RdhcpStaticPortEntry | 1.3.6.1.4.1.2882.2.1.1.2.5.5.1 | NA | ||
row · not-accessible · current An entry containing DHCP server information of the switch. | ||||
| CdhcpStaticPortIndex | 1.3.6.1.4.1.2882.2.1.1.2.5.5.1.1 | Integer32 | NA | |
column · Integer32 · not-accessible · current The index of the StaticPort Table. | ||||
| CdhcpStaticPortNumber | 1.3.6.1.4.1.2882.2.1.1.2.5.5.1.2 | INTEGER | RW | |
column · INTEGER · read-write · current The port number . | ||||
| CdhcpStaticPortIp | 1.3.6.1.4.1.2882.2.1.1.2.5.5.1.3 | IpAddress | RW | |
column · IpAddress · read-write · current The IP address . | ||||
| CdhcpStaticPortStatus | 1.3.6.1.4.1.2882.2.1.1.2.5.5.1.4 | RowStatus | RC | |
column · RowStatus · read-create · current The status of a static port entry. | ||||
| TdhcpOption82Table | 1.3.6.1.4.1.2882.2.1.1.2.5.6 | NA | ||
table · not-accessible · current DHCP server option82 table. | ||||
| RdhcpOption82Entry | 1.3.6.1.4.1.2882.2.1.1.2.5.6.1 | NA | ||
row · not-accessible · current DHCP server option82 entry. | ||||
| CdhcpOption82Index | 1.3.6.1.4.1.2882.2.1.1.2.5.6.1.1 | Integer32 | NA | |
column · Integer32 · not-accessible · current The index of the table. | ||||
| CdhcpOption82CircuitIdType | 1.3.6.1.4.1.2882.2.1.1.2.5.6.1.2 | INTEGER | RW | |
column · INTEGER · read-write · current The Circuit-ID type of this option.
| ||||
| CdhcpOption82CircuitIdValue | 1.3.6.1.4.1.2882.2.1.1.2.5.6.1.3 | OCTET STRING | RW | |
column · OCTET STRING · read-write · current The Circuit-ID value of this option. | ||||
| CdhcpOption82RemoteIdType | 1.3.6.1.4.1.2882.2.1.1.2.5.6.1.4 | INTEGER | RW | |
column · INTEGER · read-write · current The Remote-ID type of this option.
| ||||
| CdhcpOption82RemoteIdValue | 1.3.6.1.4.1.2882.2.1.1.2.5.6.1.5 | OCTET STRING | RW | |
column · OCTET STRING · read-write · current The Remote-ID value of this option. | ||||
| CdhcpOption82Ip | 1.3.6.1.4.1.2882.2.1.1.2.5.6.1.6 | IpAddress | RW | |
column · IpAddress · read-write · current The IP Address bind to this option. | ||||
| CdhcpOption82Status | 1.3.6.1.4.1.2882.2.1.1.2.5.6.1.7 | RowStatus | RC | |
column · RowStatus · read-create · current he status of a static port entry. | ||||
| TdhcpServerLeasedTable | 1.3.6.1.4.1.2882.2.1.1.2.5.7 | NA | ||
table · not-accessible · current Table of descriptive information and configuration about DHCP server of the switch. | ||||
| RdhcpServerLeasedEntry | 1.3.6.1.4.1.2882.2.1.1.2.5.7.1 | NA | ||
row · not-accessible · current An entry containing DHCP server information of the switch. | ||||
| CdhcpServerLeasedIndex | 1.3.6.1.4.1.2882.2.1.1.2.5.7.1.1 | Integer32 | NA | |
column · Integer32 · not-accessible · current The index of the Leased Table. | ||||
| CdhcpServerLeasedIp | 1.3.6.1.4.1.2882.2.1.1.2.5.7.1.2 | IpAddress | RO | |
column · IpAddress · read-only · current The client IP address. | ||||
| CdhcpServerLeasedMac | 1.3.6.1.4.1.2882.2.1.1.2.5.7.1.3 | MacAddress | RO | |
column · MacAddress · read-only · current The client MAC address. | ||||
| CdhcpServerLeasedType | 1.3.6.1.4.1.2882.2.1.1.2.5.7.1.4 | INTEGER | RO | |
column · INTEGER · read-only · current .
| ||||
| CdhcpServerLeasedTime | 1.3.6.1.4.1.2882.2.1.1.2.5.7.1.5 | Integer32 | RO | |
column · Integer32 · read-only · current The lease time of the client. | ||||
| SdhcpRelayAgentEnable | 1.3.6.1.4.1.2882.2.1.1.2.5.8 | INTEGER | RW | |
scalar · INTEGER · read-write · current Enable or disable dhcp relay agent function.
| ||||
| SdhcpRelayAgentPolicy | 1.3.6.1.4.1.2882.2.1.1.2.5.9 | INTEGER | RW | |
scalar · INTEGER · read-write · current Keep(1): Keeps the original option 82 field and forwards to server
drop(2): Drops the option 82 field and do not add any option 82 field
replace(3): Replaces the existing option 82 field and adds new option
82 field. (This is the default setting)
| ||||
| TdhcpRelayAgentCircuitIdTable | 1.3.6.1.4.1.2882.2.1.1.2.5.10 | NA | ||
table · not-accessible · current Description. | ||||
| RdhcpRelayAgentCircuitIdEntry | 1.3.6.1.4.1.2882.2.1.1.2.5.10.1 | NA | ||
| CdhcpRelayAgentCircuitIdPortNum | 1.3.6.1.4.1.2882.2.1.1.2.5.10.1.1 | Integer32 | RO | |
column · Integer32 · read-only · current Description. | ||||
| CdhcpRelayAgentCircuitIdType | 1.3.6.1.4.1.2882.2.1.1.2.5.10.1.2 | INTEGER | RW | |
column · INTEGER · read-write · current Circuit-ID type of the Option82 added by Relay Agent.
| ||||
| CdhcpRelayAgentCircuitIdValue | 1.3.6.1.4.1.2882.2.1.1.2.5.10.1.3 | OCTET STRING | RW | |
column · OCTET STRING · read-write · current Circuit-ID value of the Option82 added by Relay Agent, the format can be String or Hexadecimal value. | ||||
| CdhcpRelayAgentCircuitIdDisplay | 1.3.6.1.4.1.2882.2.1.1.2.5.10.1.4 | OCTET STRING | RO | |
column · OCTET STRING · read-only · current Display the Circuit-ID value by Hexadecimal format | ||||
| SdhcpRelayAgentRemoteIdType | 1.3.6.1.4.1.2882.2.1.1.2.5.11 | INTEGER | RW | |
scalar · INTEGER · read-write · current Remote-ID type of the Option82 added by Relay Agent.
| ||||
| SdhcpRelayAgentRemoteIdValue | 1.3.6.1.4.1.2882.2.1.1.2.5.12 | OCTET STRING | RW | |
scalar · OCTET STRING · read-write · current Remote-ID value of the Option82 added by Relay Agent, the format can be String or Hexadecimal value. | ||||
| SdhcpRelayAgentRemoteIdDisplay | 1.3.6.1.4.1.2882.2.1.1.2.5.13 | OCTET STRING | RW | |
scalar · OCTET STRING · read-write · current Remote-ID value of the Option82 added by Relay Agent. | ||||
| TdhcpHelperAddressTable | 1.3.6.1.4.1.2882.2.1.1.2.5.14 | NA | ||
table · not-accessible · current Table of descriptive information and configuration about DHCP relay helper address of the switch. | ||||
| RdhcpHelperAddressEntry | 1.3.6.1.4.1.2882.2.1.1.2.5.14.1 | NA | ||
row · not-accessible · current An entry containing DHCP relay information of the switch.
| ||||
| CdhcpHelperAddress | 1.3.6.1.4.1.2882.2.1.1.2.5.14.1.1 | IpAddress | RW | |
column · IpAddress · read-write · current The IP address . | ||||
| NbackupAndRestore | 1.3.6.1.4.1.2882.2.1.1.2.6 | |||
| SbackupServerIP | 1.3.6.1.4.1.2882.2.1.1.2.6.1 | IpAddress | RW | |
scalar · IpAddress · read-write · current The IP address of a TFTP server to which a startup configuration can be uploaded. | ||||
| SbackupAgentBoardFwFileName | 1.3.6.1.4.1.2882.2.1.1.2.6.2 | DisplayString (SIZE (0..80)) | RW | |
scalar · DisplayString (SIZE (0..80)) · read-write · current The filename to backup to. | ||||
| SbackupStatus | 1.3.6.1.4.1.2882.2.1.1.2.6.3 | INTEGER | RW | |
scalar · INTEGER · read-write · current Setting this object to active(1) trigger the TFTP upload action. Setting this object to notActive(2) has no effect. The system always returns the value notActive(2) when this object is read.
| ||||
| SrestoreServerIP | 1.3.6.1.4.1.2882.2.1.1.2.6.4 | IpAddress | RW | |
scalar · IpAddress · read-write · current The IP address of a TFTP server from which the startup configuration can be downloaded. | ||||
| SrestoreAgentBoardFwFileName | 1.3.6.1.4.1.2882.2.1.1.2.6.5 | DisplayString (SIZE (0..80)) | RW | |
scalar · DisplayString (SIZE (0..80)) · read-write · current The file name to restore from. | ||||
| SrestoreStatus | 1.3.6.1.4.1.2882.2.1.1.2.6.6 | INTEGER | RW | |
scalar · INTEGER · read-write · current Setting this object to active(1) trigger the TFTP download action. Setting this object to notActive(2) has no effect. The system always returns the value notActive(2) when this object is read.
| ||||
| NtftpUpgrade | 1.3.6.1.4.1.2882.2.1.1.2.7 | |||
| StftpDownloadServerIP | 1.3.6.1.4.1.2882.2.1.1.2.7.1 | IpAddress | RW | |
scalar · IpAddress · read-write · current The IP address of a TFTP server where a firmware image can be downloaded. | ||||
| StftpDownloadAgentBoardFwFileName | 1.3.6.1.4.1.2882.2.1.1.2.7.2 | DisplayString (SIZE (0..80)) | RW | |
scalar · DisplayString (SIZE (0..80)) · read-write · current The file name of the firmware to be downloaded. | ||||
| StftpDownloadStatus | 1.3.6.1.4.1.2882.2.1.1.2.7.3 | INTEGER | RW | |
scalar · INTEGER · read-write · current Setting this object to active(1) trigger the TFTP download action. Setting this object to notActive(2) has no effect. The system always returns the value notActive(2) when this object is read.
| ||||
| NfactoryDefault | 1.3.6.1.4.1.2882.2.1.1.2.8 | |||
| SfactoryDefaultActive | 1.3.6.1.4.1.2882.2.1.1.2.8.1 | INTEGER | RW | |
scalar · INTEGER · read-write · current Set to active(1) to reload factory default configuration. Reloading factory default will overwrite your current configuration file with factocy default configuration while current IP configuration is reserved. Please reboot the device to make factory default configuration take effect. Set notActive(2) has no effect. The system always returns the value notActive(2) when this object is read.
| ||||
| NsystemReboot | 1.3.6.1.4.1.2882.2.1.1.2.9 | |||
| SsystemRebootActive | 1.3.6.1.4.1.2882.2.1.1.2.9.1 | INTEGER | RW | |
scalar · INTEGER · read-write · current Set active(1) to restart the device. Set to notActive(2) has no effect. The device always returns the value notActive(2) when this object is read.
| ||||
| NportConfiguration | 1.3.6.1.4.1.2882.2.1.1.3 | |||
| NportControl | 1.3.6.1.4.1.2882.2.1.1.3.1 | |||
| TportCtrlTable | 1.3.6.1.4.1.2882.2.1.1.3.1.1 | NA | ||
table · not-accessible · current Table of information and configuration for each ports. | ||||
| RportCtrlEntry | 1.3.6.1.4.1.2882.2.1.1.3.1.1.1 | NA | ||
row · not-accessible · current An entry containing information and configuration for a port.
| ||||
| CportCtrlIndex | 1.3.6.1.4.1.2882.2.1.1.3.1.1.1.1 | INTEGER | NA | |
column · INTEGER · not-accessible · current Index of the port control entry. | ||||
| CportCtrlPortName | 1.3.6.1.4.1.2882.2.1.1.3.1.1.1.2 | DisplayString (SIZE (0..7)) | RO | |
column · DisplayString (SIZE (0..7)) · read-only · current The name of port. | ||||
| CportCtrlPortStatus | 1.3.6.1.4.1.2882.2.1.1.3.1.1.1.3 | INTEGER | RW | |
column · INTEGER · read-write · current To enable or disable of this port.
| ||||
| CportCtrlSpeedAndDuplex | 1.3.6.1.4.1.2882.2.1.1.3.1.1.1.4 | INTEGER | RW | |
column · INTEGER · read-write · current Speed and duplex configuraion. Different speed and duplex modes are available. There are speeds: 1000 megabits per second (Gigabit Ethernet), 100 megabits per second (Fast Ethernet), and 10 megabits per second (Legacy Ethernet). Full-duplex allows packets to be transmitted in both directions at the same time, while half-duplex allows a device to either transmit or receive, but not both at the same time. Full-duplex may have double bandwidth than half-duplex. You can configure manually from the possible options, listed from best to worst: 1Gb full-duplex(6) 100Mb full-duplex(5) 100Mb half-duplex(4) 10Mb full-duplex(3) 10Mb half-duplex(2) Set to autoNegotiation(1) to allow the two interfaces on the link to exchange the capabilities and characteristics of the each side, and select the best operating mode automatically when a cable is plugged in.
| ||||
| CportCtrlFlowControl | 1.3.6.1.4.1.2882.2.1.1.3.1.1.1.5 | INTEGER | RW | |
column · INTEGER · read-write · current Flow control configuration. Flow control is used to throttle the throughput rate of an end station to avoid dropping packets during network congestion. If flow control mode is not set and if there is no packet buffer space available, the incoming packets are discarded. Symmetric Flow Control stops and restarts packet transmission by transmitting and receiving pause frames. When a port's free buffer space is almost empty, the device send out a Pause frame to stop the remove node from sending more frames into the switch. When congestion on the port is relieved, the device send out a Pause frame with pause time equal to zero, making the remove node resume transmission.
| ||||
| CportCtrlPortDescription | 1.3.6.1.4.1.2882.2.1.1.3.1.1.1.6 | DisplayString (SIZE (0..138)) | RW | |
column · DisplayString (SIZE (0..138)) · read-write · current The description of port. | ||||
| NportStatus | 1.3.6.1.4.1.2882.2.1.1.3.2 | |||
| TportStatusTable | 1.3.6.1.4.1.2882.2.1.1.3.2.1 | NA | ||
table · not-accessible · current Table of descriptive and statistics information about each ports. | ||||
| RportStatusEntry | 1.3.6.1.4.1.2882.2.1.1.3.2.1.1 | NA | ||
row · not-accessible · current An entry containing statistics information of a port.
| ||||
| CportStatusIndex | 1.3.6.1.4.1.2882.2.1.1.3.2.1.1.1 | Integer32 | RO | |
column · Integer32 · read-only · current Index of port statistic table. | ||||
| CportStatusType | 1.3.6.1.4.1.2882.2.1.1.3.2.1.1.2 | INTEGER | RO | |
column · INTEGER · read-only · current Indicates the type of the port.
| ||||
| CportStatusLink | 1.3.6.1.4.1.2882.2.1.1.3.2.1.1.3 | INTEGER | RO | |
column · INTEGER · read-only · current Indicate the link state of the port.
| ||||
| CportStatusState | 1.3.6.1.4.1.2882.2.1.1.3.2.1.1.4 | INTEGER | RO | |
column · INTEGER · read-only · current Indicate the state of the port.
| ||||
| CportStatusSpeedDuplex | 1.3.6.1.4.1.2882.2.1.1.3.2.1.1.5 | INTEGER | RO | |
column · INTEGER · read-only · current Indicate the speed and duplex mode of the port.
| ||||
| CportStatusFlowCtrl | 1.3.6.1.4.1.2882.2.1.1.3.2.1.1.6 | INTEGER | RO | |
column · INTEGER · read-only · current Indicate the flow control status of the port.
| ||||
| CsfpVender | 1.3.6.1.4.1.2882.2.1.1.3.2.1.1.7 | DisplayString | RO | |
column · DisplayString · read-only · current The vender name of the Small Form Pluggable (SFP) optical transceiver module. | ||||
| CsfpWavelength | 1.3.6.1.4.1.2882.2.1.1.3.2.1.1.8 | Integer32 | RO | |
column · Integer32 · read-only · current The wave length in nanometers (nm) of the Small Form Pluggable (SFP) optical transceiver module. | ||||
| CsfpDistance | 1.3.6.1.4.1.2882.2.1.1.3.2.1.1.9 | Integer32 | RO | |
column · Integer32 · read-only · current The maximum transimission distance in meters of the Small Form Pluggable (SFP) optical transceiver module. | ||||
| TportSfpTable | 1.3.6.1.4.1.2882.2.1.1.3.2.2 | NA | ||
table · not-accessible · current Table of descriptive information about SFP | ||||
| RportSfpEntry | 1.3.6.1.4.1.2882.2.1.1.3.2.2.1 | NA | ||
| CportSfpIndex | 1.3.6.1.4.1.2882.2.1.1.3.2.2.1.1 | Integer32 | RO | |
column · Integer32 · read-only · current Index of port SFP table. | ||||
| CportSfpEject | 1.3.6.1.4.1.2882.2.1.1.3.2.2.1.2 | INTEGER | RW | |
column · INTEGER · read-write · current Eject SFP
| ||||
| CportSfpScan | 1.3.6.1.4.1.2882.2.1.1.3.2.2.1.3 | INTEGER | RW | |
column · INTEGER · read-write · current Scan SFP
| ||||
| CportSfpDdmStatus | 1.3.6.1.4.1.2882.2.1.1.3.2.2.1.4 | INTEGER | RW | |
column · INTEGER · read-write · current (1)Enable SFP digital diagnostic and monitoring. (2)Disable SFP digital diagnostic and monitoring.
| ||||
| CportSfpDdmTempatureCurrent | 1.3.6.1.4.1.2882.2.1.1.3.2.2.1.5 | DisplayString (SIZE (0..15)) | RO | |
column · DisplayString (SIZE (0..15)) · read-only · current The current SFP Tempature of port. | ||||
| CportSfpDdmTempatureRange | 1.3.6.1.4.1.2882.2.1.1.3.2.2.1.6 | DisplayString (SIZE (0..31)) | RO | |
column · DisplayString (SIZE (0..31)) · read-only · current The range of SFP Tempature of port. | ||||
| CportSfpDdmTxPowerCurrent | 1.3.6.1.4.1.2882.2.1.1.3.2.2.1.7 | DisplayString (SIZE (0..15)) | RO | |
column · DisplayString (SIZE (0..15)) · read-only · current The current SFP Transmitted Power of port. | ||||
| CportSfpDdmTxPowerRange | 1.3.6.1.4.1.2882.2.1.1.3.2.2.1.8 | DisplayString (SIZE (0..31)) | RO | |
column · DisplayString (SIZE (0..31)) · read-only · current The range of SFP Transmitted Power of port. | ||||
| CportSfpDdmRxPowerCurrent | 1.3.6.1.4.1.2882.2.1.1.3.2.2.1.9 | DisplayString (SIZE (0..15)) | RO | |
column · DisplayString (SIZE (0..15)) · read-only · current The current SFP Receiveed Power of port. | ||||
| CportSfpDdmRxPowerRange | 1.3.6.1.4.1.2882.2.1.1.3.2.2.1.10 | DisplayString (SIZE (0..31)) | RO | |
column · DisplayString (SIZE (0..31)) · read-only · current The range of SFP Receiveed Power of port. | ||||
| NrateLimiting | 1.3.6.1.4.1.2882.2.1.1.3.3 | |||
| TrateLimitingTable | 1.3.6.1.4.1.2882.2.1.1.3.3.1 | NA | ||
table · not-accessible · current Table of descriptive information and configuration about port rate limiting. You can set up bandwidth rate and packet limitation type for each ports. Rate limiting is used to control the rate of traffic sent or received on a network interface. For ingress rate limiting, traffic that is less than or equal to the specified rate is received, whereas traffic that exceeds the rate is dropped. For egress rate limiting, traffic that is less than or equal to the specified rate is sent, whereas traffic that exceeds the rate is dropped. | ||||
| RrateLimitingEntry | 1.3.6.1.4.1.2882.2.1.1.3.3.1.1 | NA | ||
row · not-accessible · current An entry containing information and configuration about port rate limiting.
| ||||
| CrateLimitingPortNum | 1.3.6.1.4.1.2882.2.1.1.3.3.1.1.1 | Integer32 | RO | |
column · Integer32 · read-only · current The port number. | ||||
| CrateLimitingIngressLimitType | 1.3.6.1.4.1.2882.2.1.1.3.3.1.1.2 | INTEGER | RW | |
column · INTEGER · read-write · current The type of ingress packets to be filtered.
| ||||
| CrateLimitingIngressRate | 1.3.6.1.4.1.2882.2.1.1.3.3.1.1.3 | Integer32 | RW | |
column · Integer32 · read-write · current Ingress rate in Mbps, the rate range is from 1 Mbps to 100 Mbps and zero means no limit. | ||||
| CrateLimitingEgressRate | 1.3.6.1.4.1.2882.2.1.1.3.3.1.1.4 | Integer32 | RW | |
column · Integer32 · read-write · current Egress rate in Mbps, the rate range is from 1 Mbps to 100 Mbps and zero means no limit. Egress rate limiting has effect on all types of packets, including unicast, multicast and broadcast packets. | ||||
| NportTrunk | 1.3.6.1.4.1.2882.2.1.1.3.4 | |||
| NaggregatorSetting | 1.3.6.1.4.1.2882.2.1.1.3.4.1 | |||
| TportTrunkAggregatorSettingTable | 1.3.6.1.4.1.2882.2.1.1.3.4.1.1 | NA | ||
table · not-accessible · current Table of descriptive information and configuration about of each trunk group in this system. Link aggregation, or IEEE 802.3ad, is a method of combining physical network links into a single logical link for increased bandwidth. With Link aggregation we are able to increase the capacity and availability of the communications channel between devices (both switches and end stations) using existing Fast Ethernet and Gigabit Ethernet technology. Two or more Gigabit Ethernet connections are combined in order to increase the bandwidth capability and to create resilient and redundant links. A set of multiple parallel physical links between two devices is grouped together to form a single logical link. Link Aggregation also provides load balancing where the processing and communications activity is distributed across the links in a trunk so that no single link is overwhelmed. | ||||
| RportTrunkAggregatorSettingEntry | 1.3.6.1.4.1.2882.2.1.1.3.4.1.1.1 | NA | ||
row · not-accessible · current Information controlling aggregator configuration.
| ||||
| CportTrunkPortIndex | 1.3.6.1.4.1.2882.2.1.1.3.4.1.1.1.1 | INTEGER | RO | |
column · INTEGER · read-only · current The port number. | ||||
| CportTrunkAggregatorGroupId | 1.3.6.1.4.1.2882.2.1.1.3.4.1.1.1.2 | INTEGER | RW | |
column · INTEGER · read-write · current Trunk group Id. Upto 8 ports can be aggregated into a group and 5 groups can be configured in the device.
| ||||
| CportTrunkAggregatorType | 1.3.6.1.4.1.2882.2.1.1.3.4.1.1.1.3 | INTEGER | RW | |
column · INTEGER · read-write · current The Aggregator type. You can assign the aggregator staticly by setting to static(1), or setting to lacp(2) to enable the LACP protocol. The Link Aggregation Control Protocol (LACP) is required for dynamically exchanging configuration information between the peer devices in order to automatically configure and maintain link aggregation groups. The protocol is able to automatically detect the presence and capabilities of other aggregation capable devices, i.e. with LACP it is possible to specify which links in a system can be aggregated. This column has no effect if Group Id is set to none.
| ||||
| SportTrunkAggregatorSettingApply | 1.3.6.1.4.1.2882.2.1.1.3.4.1.2 | INTEGER | RW | |
scalar · INTEGER · read-write · current set active(1) to apply the configuration
| ||||
| NaggregatorStatus | 1.3.6.1.4.1.2882.2.1.1.3.4.2 | |||
| TportTrunkAggregatorStatusTable | 1.3.6.1.4.1.2882.2.1.1.3.4.2.1 | NA | ||
table · not-accessible · current Table of descriptive information about trunk groups in the device. | ||||
| RportTrunkAggregatorStatusEntry | 1.3.6.1.4.1.2882.2.1.1.3.4.2.1.1 | NA | ||
row · not-accessible · current An entry containing information about current configuration of trunk groups. | ||||
| CportTrunkAggregatorGroupIndex | 1.3.6.1.4.1.2882.2.1.1.3.4.2.1.1.1 | INTEGER | RO | |
column · INTEGER · read-only · current The trunk group identifier. | ||||
| CportTrunkAggregatorGroupType | 1.3.6.1.4.1.2882.2.1.1.3.4.2.1.1.2 | INTEGER | RO | |
column · INTEGER · read-only · current The Aggregator type.
(1) The trunk group is LACP disabled and configured staticly
by administrator.
(2) The trunk group is LACP enabled.
| ||||
| CportTrunkAggregatorGroupMember | 1.3.6.1.4.1.2882.2.1.1.3.4.2.1.1.3 | PortList | RO | |
column · PortList · read-only · current The ports are aggregated with other ports. | ||||
| CportTrunkAggregatorIndividual | 1.3.6.1.4.1.2882.2.1.1.3.4.2.1.1.4 | PortList | RO | |
column · PortList · read-only · current A port is LACP enabled but not aggregated with other ports. | ||||
| CportTrunkAggregatorLinkDown | 1.3.6.1.4.1.2882.2.1.1.3.4.2.1.1.5 | PortList | RO | |
column · PortList · read-only · current The ports which are linked down. | ||||
| NnetworkRedundancy | 1.3.6.1.4.1.2882.2.1.1.4 | |||
| NredundantRing | 1.3.6.1.4.1.2882.2.1.1.4.4 | |||
| TredundantRingConfigTable | 1.3.6.1.4.1.2882.2.1.1.4.4.1 | NA | ||
table · not-accessible · current Table of configuration about redundancy protocol in the device. | ||||
| RredundantRingConfigEntry | 1.3.6.1.4.1.2882.2.1.1.4.4.1.1 | NA | ||
row · not-accessible · current An entry containing information about current configuration of rings.
| ||||
| CsuperRingConfigId | 1.3.6.1.4.1.2882.2.1.1.4.4.1.1.1 | INTEGER (0..15) | NA | |
column · INTEGER (0..15) · not-accessible · current Ring Id. | ||||
| CsuperRingName | 1.3.6.1.4.1.2882.2.1.1.4.4.1.1.2 | DisplayString | RW | |
column · DisplayString · read-write · current Super Ring name. | ||||
| CsuperRingConfigVersion | 1.3.6.1.4.1.2882.2.1.1.4.4.1.1.3 | INTEGER | RW | |
column · INTEGER · read-write · current Super Ring funtion version selection.
Super Ring: Backward compatible with legacy super ring mechanism.
Note: This model supports v1 non-Redundancy Management mode only.
Rapid Super Ring: New mechanism. The recovery time is less than 30ms.
Any Ring:
| ||||
| CsuperRingDevicePriority | 1.3.6.1.4.1.2882.2.1.1.4.4.1.1.4 | INTEGER (0..255) | RW | |
column · INTEGER (0..255) · read-write · current Super Ring device priority setting. | ||||
| CsuperRingRingPort1 | 1.3.6.1.4.1.2882.2.1.1.4.4.1.1.5 | INTEGER | RW | |
column · INTEGER · read-write · current RingPort1 should not equal to RingRort2. | ||||
| CsuperRingRingPort2 | 1.3.6.1.4.1.2882.2.1.1.4.4.1.1.6 | INTEGER | RW | |
column · INTEGER · read-write · current RingPort2 should not equal to RingRort1. | ||||
| CsuperRingRingPort1PathCost | 1.3.6.1.4.1.2882.2.1.1.4.4.1.1.7 | INTEGER (0..255) | RW | |
| CsuperRingRingPort2PathCost | 1.3.6.1.4.1.2882.2.1.1.4.4.1.1.8 | INTEGER (0..255) | RW | |
| CsuperRingRapidDualHomingStatus | 1.3.6.1.4.1.2882.2.1.1.4.4.1.1.9 | INTEGER | RW | |
column · INTEGER · read-write · current Rapid Dual Homing funtion status. Rapid Dual Homing is a redundancy protocol, which is compatible with RSTP. (1) Rapid Dual Homing function is enabled. (2) Rapid Dual Homing function is disabled.
| ||||
| CsuperRingStatus | 1.3.6.1.4.1.2882.2.1.1.4.4.1.1.10 | RowStatus | RC | |
column · RowStatus · read-create · current Status of this ring. | ||||
| TredundantRingStatusTable | 1.3.6.1.4.1.2882.2.1.1.4.4.2 | NA | ||
table · not-accessible · current Table of status information about redundancy protocol in the device. | ||||
| RredundantRingStatusEntry | 1.3.6.1.4.1.2882.2.1.1.4.4.2.1 | NA | ||
row · not-accessible · current An entry containing information about current status of rings.
| ||||
| CsuperRingStatusId | 1.3.6.1.4.1.2882.2.1.1.4.4.2.1.1 | INTEGER (0..15) | RO | |
column · INTEGER (0..15) · read-only · current Ring Id. | ||||
| CsuperRingVersion | 1.3.6.1.4.1.2882.2.1.1.4.4.2.1.2 | INTEGER | RO | |
column · INTEGER · read-only · current Super Ring funtion version selection.
Super Ring: Backward compatible with legacy super ring mechanism.
Note: This model supports v1 non-Redundancy Management mode only.
Rapid Super Ring: New mechanism. The recovery time is less than 30ms.
Any Ring:
Not Supported:
| ||||
| CsuperRingDeviceRole | 1.3.6.1.4.1.2882.2.1.1.4.4.2.1.3 | INTEGER | RO | |
column · INTEGER · read-only · current Super Ring role status.
(1) disabled.
(2) Redundancy manager.
(3) Non redundancy manager.
| ||||
| CsuperRingRingPortList1 | 1.3.6.1.4.1.2882.2.1.1.4.4.2.1.4 | PortList | RO | |
column · PortList · read-only · current Port list for ring port1. | ||||
| CsuperRingRingPortList2 | 1.3.6.1.4.1.2882.2.1.1.4.4.2.1.5 | PortList | RO | |
column · PortList · read-only · current Port list for ring port2. | ||||
| CsuperRingRingStatus | 1.3.6.1.4.1.2882.2.1.1.4.4.2.1.6 | INTEGER | RO | |
column · INTEGER · read-only · current Super Ring ring status.
(1) Disabled - The ring on this device is disabled.
(1) Normal - Ring is complete.
(2) Abnormal - Ring is not complete.
| ||||
| CsuperRingRmMac | 1.3.6.1.4.1.2882.2.1.1.4.4.2.1.7 | MacAddress | RO | |
column · MacAddress · read-only · current RM mac address. | ||||
| CsuperRingBlockedPort | 1.3.6.1.4.1.2882.2.1.1.4.4.2.1.8 | PortList | RO | |
column · PortList · read-only · current The blocked ports in ring Normal state. | ||||
| CsuperRingRoleTransitionCount | 1.3.6.1.4.1.2882.2.1.1.4.4.2.1.9 | Integer32 | RO | |
| CsuperRingRingStateTransitionCount | 1.3.6.1.4.1.2882.2.1.1.4.4.2.1.10 | Integer32 | RO | |
| Nstp | 1.3.6.1.4.1.2882.2.1.1.4.5 | |||
| SstpModeStatus | 1.3.6.1.4.1.2882.2.1.1.4.5.1 | INTEGER | RW | |
scalar · INTEGER · read-write · current Enable Spanning Tree protocol, Rapid Spanning Tree protocol, or disable . Rapid Spanning Tree Algorithm and Protocol (RSTP) provides a loop free topology for any LAN or bridged network. RSTP is an evolution of the Spanning Tree Protocol (STP), and was introduced in the extension IEEE 802.1w, and provides for faster spanning tree convergence after a topology change.
| ||||
| SstpBridgeAddress | 1.3.6.1.4.1.2882.2.1.1.4.5.2 | DisplayString | RO | |
scalar · DisplayString · read-only · current Bridge Address. | ||||
| SstpBridgePriority | 1.3.6.1.4.1.2882.2.1.1.4.5.3 | INTEGER | RW | |
scalar · INTEGER · read-write · current A value used to identify the root bridge. The bridge with the lowest value has the highest priority and is selected as the root. Enter a number 0 through 61440 in steps of 4096. If you change the value, you must restart RSTP. This item can't be modified, if stpStatus was disabled.
| ||||
| SstpMaxAge | 1.3.6.1.4.1.2882.2.1.1.4.5.4 | Integer32 | RW | |
scalar · Integer32 · read-write · current The number of seconds a bridge waits without receiving Spanning-Tree Protocol configuration messages before attempting a reconfiguration. Enter a number 6 through 40. Note: 2*(Forward Delay Time-1) should be greater than or equal to the Max Age. The Max Age should be greater than or equal to 2*(Hello Time + 1). This item can't be modified, if stpStatus was disabled. | ||||
| SstpHelloTime | 1.3.6.1.4.1.2882.2.1.1.4.5.5 | Integer32 | RW | |
scalar · Integer32 · read-write · current The number of seconds between the transmission of Spanning-Tree Protocol configuration messages. Enter a number 1 through 10 Note: 2*(Forward Delay Time-1) should be greater than or equal to the Max Age. The Max Age should be greater than or equal to 2*(Hello Time + 1). This item can't be modified, if stpStatus was disabled. | ||||
| SstpForwardDelayTime | 1.3.6.1.4.1.2882.2.1.1.4.5.6 | Integer32 | RW | |
scalar · Integer32 · read-write · current The number of seconds a port waits before changing from its Spanning-Tree Protocol learning and listening states to the forwarding state. Enter a number 4 through 30. Note:2*(Forward Delay Time-1) should be greater than or equal to the Max Age. The Max Age should be greater than or equal to 2*(Hello Time + 1). This item can't be modified, if stpStatus was disabled. | ||||
| TstpPerPortCfgTable | 1.3.6.1.4.1.2882.2.1.1.4.5.7 | NA | ||
table · not-accessible · current Table of descriptive information and configuration about STP on each port. | ||||
| RstpPerPortCfgEntry | 1.3.6.1.4.1.2882.2.1.1.4.5.7.1 | NA | ||
| CstpPerPortCfgPortNum | 1.3.6.1.4.1.2882.2.1.1.4.5.7.1.1 | Integer32 | NA | |
column · Integer32 · not-accessible · current The port number. | ||||
| CstpPerPortCfgStpState | 1.3.6.1.4.1.2882.2.1.1.4.5.7.1.2 | INTEGER | RW | |
column · INTEGER · read-write · current Enable/Disable STP/RSTP/MSTP at this port. Disable STP state when connecting a device in order to avoid STP waiting periods.
| ||||
| CstpPerPortCfgPathCost | 1.3.6.1.4.1.2882.2.1.1.4.5.7.1.3 | Integer32 | RW | |
column · Integer32 · read-write · current The cost of the path to the other bridge from this transmitting bridge at the specified port. Enter a number from 1 through 200000000. (0 will auto set path cost to standard recommended value) | ||||
| CstpPerPortCfgPriority | 1.3.6.1.4.1.2882.2.1.1.4.5.7.1.4 | INTEGER | RW | |
column · INTEGER · read-write · current Decide which port should be blocked by priority in LAN. Enter a number from 0 through 240 in steps of 16.
| ||||
| CstpPerPortCfgLinkType | 1.3.6.1.4.1.2882.2.1.1.4.5.7.1.5 | INTEGER | RW | |
column · INTEGER · read-write · current Some of the rapid state transactions that are possible within RSTP are dependent upon whether the Port concerned can only be connected to exactly one other Bridge(ie., it is served by a point-to-point LAN segment), or can be connected to two or more Bridges(i.e., it is served by a shared medium LAN segment). The adminPointToPointMAC allow the p2p status of the link to be manipulated adminitratively.
| ||||
| CstpPerPortCfgEdgePort | 1.3.6.1.4.1.2882.2.1.1.4.5.7.1.6 | INTEGER | RW | |
column · INTEGER · read-write · current Present in implementations that support the identification of edge ports. All ports directly connected to end stations cannot create bridging loops in the network and can thus directly transition to forwarding, skipping the listening and learning stages.
| ||||
| NstpBridgeInformation | 1.3.6.1.4.1.2882.2.1.1.4.6 | |||
| TstpRootInformationTable | 1.3.6.1.4.1.2882.2.1.1.4.6.1 | NA | ||
table · not-accessible · current Table of descriptive information about root bridge of rapid spanning tree in this system. | ||||
| RstpRootInformationEntry | 1.3.6.1.4.1.2882.2.1.1.4.6.1.1 | NA | ||
row · not-accessible · current An entry in the table, containing information about root bridge information of the STP. | ||||
| CstpRootInformationIndex | 1.3.6.1.4.1.2882.2.1.1.4.6.1.1.1 | Integer32 | NA | |
column · Integer32 · not-accessible · current Index of root bridge information table. | ||||
| CstpRootInformationRootAddress | 1.3.6.1.4.1.2882.2.1.1.4.6.1.1.2 | DisplayString (SIZE (0..255)) | RO | |
column · DisplayString (SIZE (0..255)) · read-only · current Root Address. | ||||
| CstpRootInformationRootPriority | 1.3.6.1.4.1.2882.2.1.1.4.6.1.1.3 | Integer32 | RO | |
column · Integer32 · read-only · current Root Priority. | ||||
| CstpRootInformationRootPort | 1.3.6.1.4.1.2882.2.1.1.4.6.1.1.4 | DisplayString (SIZE (0..80)) | RO | |
column · DisplayString (SIZE (0..80)) · read-only · current Root Port. | ||||
| CstpRootInformationRootPathCost | 1.3.6.1.4.1.2882.2.1.1.4.6.1.1.5 | Integer32 | RO | |
column · Integer32 · read-only · current Root Path Cost. | ||||
| CstpRootInformationMaxAge | 1.3.6.1.4.1.2882.2.1.1.4.6.1.1.6 | Integer32 | RO | |
column · Integer32 · read-only · current Max Age. | ||||
| CstpRootInformationHelloTime | 1.3.6.1.4.1.2882.2.1.1.4.6.1.1.7 | Integer32 | RO | |
column · Integer32 · read-only · current Hello Time. | ||||
| CstpRootInformationForwardDelay | 1.3.6.1.4.1.2882.2.1.1.4.6.1.1.8 | Integer32 | RO | |
column · Integer32 · read-only · current Forward Delay Time. | ||||
| TstpPerPortInfoTable | 1.3.6.1.4.1.2882.2.1.1.4.6.2 | NA | ||
table · not-accessible · current Table of descriptive information and configuration about rapid spanning tree (Per port). | ||||
| RstpPerPortInfoEntry | 1.3.6.1.4.1.2882.2.1.1.4.6.2.1 | NA | ||
row · not-accessible · current An entry in the table, containing inforamtion about STP (Per port). | ||||
| CstpPerPortInfoPortNum | 1.3.6.1.4.1.2882.2.1.1.4.6.2.1.1 | Integer32 | NA | |
column · Integer32 · not-accessible · current Port number. | ||||
| CstpPerPortInfoRole | 1.3.6.1.4.1.2882.2.1.1.4.6.2.1.2 | INTEGER | RO | |
column · INTEGER · read-only · current Descriptive information about RSTP switch port roles:
root(1) A forwarding port that has been elected for
the spanning-tree topology.
alternate(2) An alternate path to the root bridge. This
path is different than using the root port.
designated(3) A forwarding port for every LAN segment.
backup(4) A backup/redundant path to a segment where
another switch port already connects.
disabled(5) RSTP is disabled on this port.
| ||||
| CstpPerPortInfoState | 1.3.6.1.4.1.2882.2.1.1.4.6.2.1.3 | INTEGER | RO | |
column · INTEGER · read-only · current
| ||||
| CstpPerPortInfoPathCost | 1.3.6.1.4.1.2882.2.1.1.4.6.2.1.4 | Integer32 | RO | |
column · Integer32 · read-only · current The cost of the path to the other bridge from this transmitting bridge at the specified port. Enter a number 1 through 200000000. | ||||
| CstpPerPortInfoPriority | 1.3.6.1.4.1.2882.2.1.1.4.6.2.1.5 | Integer32 | RO | |
column · Integer32 · read-only · current Decide which port should be blocked by priority in LAN. Enter a number 0 through 240 in steps of 16. | ||||
| CstpPerPortInfoLinkType | 1.3.6.1.4.1.2882.2.1.1.4.6.2.1.6 | INTEGER | RO | |
column · INTEGER · read-only · current Some of the rapid state transactions that are possible within RSTP are dependent upon whether the Port concerned can only be connected to exactly one other Bridge(ie., it is served by a point-to-point LAN segment), or can be connected to two or more Bridges(i.e., it is served by a shared medium LAN segment). The adminPointToPointMAC allow the p2p status of the link to be manipulated adminitratively. STP does not support this function.
| ||||
| CstpPerPortInfoEdgePort | 1.3.6.1.4.1.2882.2.1.1.4.6.2.1.7 | INTEGER | RO | |
column · INTEGER · read-only · current Present in implementations that support the identification of edge ports. All ports directly connected to end stations cannot create bridging loops in the network and can thus directly transition to forwarding, skipping the listening and learning stages.
| ||||
| Nmstp | 1.3.6.1.4.1.2882.2.1.1.4.7 | |||
| SmstpRegionName | 1.3.6.1.4.1.2882.2.1.1.4.7.1 | DisplayString | RW | |
scalar · DisplayString · read-write · current MSTP region name. | ||||
| SmstpRegionRevision | 1.3.6.1.4.1.2882.2.1.1.4.7.2 | Integer32 | RW | |
scalar · Integer32 · read-write · current MSTP region revision. | ||||
| TmstpPerInstCfgTable | 1.3.6.1.4.1.2882.2.1.1.4.7.3 | NA | ||
table · not-accessible · current Table of descriptive information and configuration about STP on each port. | ||||
| RmstpPerInstCfgEntry | 1.3.6.1.4.1.2882.2.1.1.4.7.3.1 | NA | ||
row · not-accessible · current Information configuring MSTP on a instance. | ||||
| CmstpPerInstCfgInstanceID | 1.3.6.1.4.1.2882.2.1.1.4.7.3.1.1 | Integer32 | NA | |
column · Integer32 · not-accessible · current The instance ID. | ||||
| CmstpPerInstCfgVlanGroup | 1.3.6.1.4.1.2882.2.1.1.4.7.3.1.2 | DisplayString | RW | |
column · DisplayString · read-write · current VLAN group of instance. | ||||
| CmstpPerInstCfgInstancePriority | 1.3.6.1.4.1.2882.2.1.1.4.7.3.1.3 | INTEGER | RW | |
column · INTEGER · read-write · current A value used to identify the instance root. The instance with the lowest value has the highest priority and is selected as the root. Enter a number 0 through 61440 in steps of 4096.
| ||||
| CmstpPerInstCfgStatus | 1.3.6.1.4.1.2882.2.1.1.4.7.3.1.4 | RowStatus | RC | |
column · RowStatus · read-create · current Status of this Instance. | ||||
| TmstpPerPortCfgTable | 1.3.6.1.4.1.2882.2.1.1.4.7.4 | NA | ||
table · not-accessible · current Table of descriptive information and configuration about MSTP on each port. | ||||
| RmstpPerPortCfgEntry | 1.3.6.1.4.1.2882.2.1.1.4.7.4.1 | NA | ||
| CmstpPerPortCfgIndex | 1.3.6.1.4.1.2882.2.1.1.4.7.4.1.1 | Integer32 | NA | |
column · Integer32 · not-accessible · current The index of MstpPerPortCfgEntry. | ||||
| CmstpPerPortCfgInstanceID | 1.3.6.1.4.1.2882.2.1.1.4.7.4.1.2 | Integer32 | RO | |
column · Integer32 · read-only · current The instance ID. | ||||
| CmstpPerPortCfgPortNum | 1.3.6.1.4.1.2882.2.1.1.4.7.4.1.3 | Integer32 | RO | |
column · Integer32 · read-only · current The port number. | ||||
| CmstpPerPortCfgPathCost | 1.3.6.1.4.1.2882.2.1.1.4.7.4.1.4 | Integer32 | RW | |
column · Integer32 · read-write · current The cost of the path to the other bridge from this transmitting bridge at the specified port. Enter a number from 1 through 200000000. (0 will auto set path cost to standard recommended value) | ||||
| CmstpPerPortCfgPriority | 1.3.6.1.4.1.2882.2.1.1.4.7.4.1.5 | INTEGER | RW | |
column · INTEGER · read-write · current Decide which port should be blocked by priority in LAN. Enter a number from 0 through 240 in steps of 16.
| ||||
| CmstpPerPortCfgLinkType | 1.3.6.1.4.1.2882.2.1.1.4.7.4.1.6 | INTEGER | RW | |
column · INTEGER · read-write · current Some of the rapid state transactions that are possible within RSTP are dependent upon whether the Port concerned can only be connected to exactly one other Bridge(ie., it is served by a point-to-point LAN segment), or can be connected to two or more Bridges(i.e., it is served by a shared medium LAN segment). The adminPointToPointMAC allow the p2p status of the link to be manipulated adminitratively.
| ||||
| CmstpPerPortCfgEdgePort | 1.3.6.1.4.1.2882.2.1.1.4.7.4.1.7 | INTEGER | RW | |
column · INTEGER · read-write · current Present in implementations that support the identification of edge ports. All ports directly connected to end stations cannot create bridging loops in the network and can thus directly transition to forwarding, skipping the listening and learning stages.
| ||||
| NmstpBridgeInformation | 1.3.6.1.4.1.2882.2.1.1.4.8 | |||
| TmstpRootInformationTable | 1.3.6.1.4.1.2882.2.1.1.4.8.1 | NA | ||
table · not-accessible · current Table of descriptive information about root bridge of rapid spanning tree in this system. | ||||
| RmstpRootInformationEntry | 1.3.6.1.4.1.2882.2.1.1.4.8.1.1 | NA | ||
row · not-accessible · current An entry in the table, containing information about root bridge information of the MSTP. | ||||
| CmstpRootInformationInstanceID | 1.3.6.1.4.1.2882.2.1.1.4.8.1.1.1 | Integer32 | RO | |
column · Integer32 · read-only · current The instance ID. | ||||
| CmstpRootInformationRootAddress | 1.3.6.1.4.1.2882.2.1.1.4.8.1.1.2 | DisplayString (SIZE (0..255)) | RO | |
column · DisplayString (SIZE (0..255)) · read-only · current Root Address. | ||||
| CmstpRootInformationRootPriority | 1.3.6.1.4.1.2882.2.1.1.4.8.1.1.3 | Integer32 | RO | |
column · Integer32 · read-only · current Root Priority. | ||||
| CmstpRootInformationRootPort | 1.3.6.1.4.1.2882.2.1.1.4.8.1.1.4 | DisplayString (SIZE (0..80)) | RO | |
column · DisplayString (SIZE (0..80)) · read-only · current Root Port. | ||||
| CmstpRootInformationRootPathCost | 1.3.6.1.4.1.2882.2.1.1.4.8.1.1.5 | Integer32 | RO | |
column · Integer32 · read-only · current Root Path Cost. | ||||
| CmstpRootInformationMaxAge | 1.3.6.1.4.1.2882.2.1.1.4.8.1.1.6 | Integer32 | RO | |
column · Integer32 · read-only · current Max Age. | ||||
| CmstpRootInformationHelloTime | 1.3.6.1.4.1.2882.2.1.1.4.8.1.1.7 | Integer32 | RO | |
column · Integer32 · read-only · current Hello Time. | ||||
| CmstpRootInformationForwardDelay | 1.3.6.1.4.1.2882.2.1.1.4.8.1.1.8 | Integer32 | RO | |
column · Integer32 · read-only · current Forward Delay Time. | ||||
| TmstpPerPortInfoTable | 1.3.6.1.4.1.2882.2.1.1.4.8.2 | NA | ||
table · not-accessible · current Table of descriptive information and configuration about rapid spanning tree (Per port). | ||||
| RmstpPerPortInfoEntry | 1.3.6.1.4.1.2882.2.1.1.4.8.2.1 | NA | ||
row · not-accessible · current An entry in the table, containing information about MSTP (Per port).
| ||||
| CmstpPerPortInfoIndex | 1.3.6.1.4.1.2882.2.1.1.4.8.2.1.1 | Integer32 | NA | |
column · Integer32 · not-accessible · current The index of MstpPerPortInfoEntry. | ||||
| CmstpPerPortInfoInstanceID | 1.3.6.1.4.1.2882.2.1.1.4.8.2.1.2 | Integer32 | RO | |
column · Integer32 · read-only · current The instance ID. | ||||
| CmstpPerPortInfoPortNum | 1.3.6.1.4.1.2882.2.1.1.4.8.2.1.3 | Integer32 | RO | |
column · Integer32 · read-only · current Port number. | ||||
| CmstpPerPortInfoRole | 1.3.6.1.4.1.2882.2.1.1.4.8.2.1.4 | INTEGER | RO | |
column · INTEGER · read-only · current Descriptive information about MSTP switch port roles:
disabled(1) MSTP is disabled on this port.
root(2) A forwarding port that has been elected for
the spanning-tree topology.
designated(3) A forwarding port for every LAN segment.
alternate(4) An alternate path to the root bridge. This
path is different than using the root port.
backup(5) A backup/redundant path to a segment where
another switch port already connects.
| ||||
| CmstpPerPortInfoState | 1.3.6.1.4.1.2882.2.1.1.4.8.2.1.5 | INTEGER | RO | |
column · INTEGER · read-only · current
| ||||
| CmstpPerPortInfoPathCost | 1.3.6.1.4.1.2882.2.1.1.4.8.2.1.6 | Integer32 | RO | |
column · Integer32 · read-only · current The cost of the path to the other bridge from this transmitting bridge at the specified port. Enter a number 1 through 200000000. | ||||
| CmstpPerPortInfoPriority | 1.3.6.1.4.1.2882.2.1.1.4.8.2.1.7 | Integer32 | RO | |
column · Integer32 · read-only · current Decide which port should be blocked by priority in LAN. Enter a number 0 through 240 in steps of 16. | ||||
| CmstpPerPortInfoLinkType | 1.3.6.1.4.1.2882.2.1.1.4.8.2.1.8 | INTEGER | RO | |
column · INTEGER · read-only · current Some of the rapid state transactions that are possible within MSTP are dependent upon whether the Port concerned can only be connected to exactly one other Bridge(ie., it is served by a point-to-point LAN segment), or can be connected to two or more Bridges(i.e., it is served by a shared medium LAN segment). The adminPointToPointMAC allow the p2p status of the link to be manipulated adminitratively.
| ||||
| CmstpPerPortInfoEdgePort | 1.3.6.1.4.1.2882.2.1.1.4.8.2.1.9 | INTEGER | RO | |
column · INTEGER · read-only · current Present in implementations that support the identification of edge ports. All ports directly connected to end stations cannot create bridging loops in the network and can thus directly transition to forwarding, skipping the listening and learning stages.
| ||||
| Nvlan | 1.3.6.1.4.1.2882.2.1.1.5 | |||
| SvlanManagementVlan | 1.3.6.1.4.1.2882.2.1.1.5.1 | INTEGER | RW | |
scalar · INTEGER · read-write · current The VLAN from which managemnet traffic can access the device. By default, VLAN 1 is management VLAN. | ||||
| Nieee8021qVlan | 1.3.6.1.4.1.2882.2.1.1.5.2 | |||
| Tdot1qPortVlanTable | 1.3.6.1.4.1.2882.2.1.1.5.2.1 | NA | ||
table · not-accessible · current A table containing per port control and status information for IEEE802.1Q VLAN configuration in the device. | ||||
| Rdot1qPortVlanEntry | 1.3.6.1.4.1.2882.2.1.1.5.2.1.1 | NA | ||
row · not-accessible · current Information controlling IEEE802.1Q VLAN configuration for a port on the device.
| ||||
| Cdot1qPortIndex | 1.3.6.1.4.1.2882.2.1.1.5.2.1.1.1 | INTEGER (1..10) | RO | |
column · INTEGER (1..10) · read-only · current The port identifier. | ||||
| Cdot1qPvid | 1.3.6.1.4.1.2882.2.1.1.5.2.1.1.2 | INTEGER (1..4094) | RW | |
column · INTEGER (1..4094) · read-write · current The default Port VID, the VLAN ID assigned to an untagged frame or a Priority-Tagged frame received on the port. | ||||
| Cdot1qPortAcceptableFrameTypes | 1.3.6.1.4.1.2882.2.1.1.5.2.1.1.3 | INTEGER | RW | |
column · INTEGER · read-write · current When admitOnlyVlanTagged(2) the device will discard untagged frames or Priority-Tagged only frames received on this port. When admitAll(1), untagged frames or Priority-Tagged only frames received on this port will be accepted and assigned the PVID for this frame. This control does not affect VLAN independent BPDU frames, such as SuperRing, STP, GVRP and LACP. It does affect VLAN dependent BPDU frames, such as GMRP.
| ||||
| Cdot1qPortIngressFiltering | 1.3.6.1.4.1.2882.2.1.1.5.2.1.1.4 | INTEGER | RW | |
column · INTEGER · read-write · current When true(1) the device will discard incoming frames whose VLAN classification do not include this port in its Member set. When false(2), the port will accept all incoming frames regardless its VLAN classification. This control does not affect VLAN independent BPDU frames, such as SuperRing, STP, GVRP and LACP. It does affect VLAN dependent BPDU frames, such as GMRP.
| ||||
| Tdot1qVlanStaticTable | 1.3.6.1.4.1.2882.2.1.1.5.2.2 | NA | ||
table · not-accessible · current A table containing configuration information for each VLAN configured into the device by management. All entries are permanent and will be restored after the device is reset. Upto 64 VLANs can be configured in this device. IEEE 802.1Q Virtual LANs (VLANs) allow a single physical LAN to be partitioned into several smaller logical LANs. VLANs limit the broadcast domain, improve security and performance and are ideal for separating systems or departments from each other. | ||||
| Rdot1qVlanStaticEntry | 1.3.6.1.4.1.2882.2.1.1.5.2.2.1 | NA | ||
row · not-accessible · current Static information of a VLAN configured into the device by management.
| ||||
| Cdot1qVlanIndex | 1.3.6.1.4.1.2882.2.1.1.5.2.2.1.1 | INTEGER (1..4094) | RO | |
column · INTEGER (1..4094) · read-only · current The VLAN Identifier (VID) refering to this VLAN. The valid range is from 1 to 4094. | ||||
| Cdot1qVlanStaticName | 1.3.6.1.4.1.2882.2.1.1.5.2.2.1.2 | DisplayString (SIZE (0..12)) | RW | |
column · DisplayString (SIZE (0..12)) · read-write · current An administratively assigned string, which is used to identify the VLAN. | ||||
| Cdot1qVlanStaticEgressPorts | 1.3.6.1.4.1.2882.2.1.1.5.2.2.1.3 | PortList | RO | |
column · PortList · read-only · current The set of ports which are permanently configured to transmitting traffic for this VLAN as either tagged or untagged frames. Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'. Changes to this object affect the per-port per-VLAN Registrar control for Registration Fixed for the relevant GVRP state machine on each port. A port may not be added in this set if it is already a member of the set of ports in dot1qVlanForbiddenEgressPorts. The default value of this object is a string of zeros, indicating not fixed. | ||||
| Cdot1qVlanStaticUntaggedPorts | 1.3.6.1.4.1.2882.2.1.1.5.2.2.1.4 | PortList | RC | |
column · PortList · read-create · current The set of ports which are permanently configured to transmitting traffic for this VLAN as untagged frames. Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'. Changes to this object affect the per-port per-VLAN Registrar control for Registration Fixed for the relevant GVRP state machine on each port. The default value of this object for the default VLAN is a portlist including all ports. There is no specified default for other VLANs. | ||||
| Cdot1qVlanStaticTaggedPorts | 1.3.6.1.4.1.2882.2.1.1.5.2.2.1.5 | PortList | RC | |
column · PortList · read-create · current The set of ports which are permanently configured to transmitting traffic for this VLAN as tagged frames. Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'. Changes to this object affect the per-port per-VLAN Registrar control for Registration Fixed for the relevant GVRP state machine on each port. The default value of this object for the default VLAN is a portlist including all ports. There is no specified default for other VLANs. | ||||
| Cdot1qVlanStaticRowStatus | 1.3.6.1.4.1.2882.2.1.1.5.2.2.1.6 | RowStatus | RC | |
column · RowStatus · read-create · current This object is used to manage to creation and deletion of a VLAN, and is used to indicate the status of this entry. To Creating and activate a VLAN, first select a unused VID for dot1qVlanIndex and then set its dot1qVlanStaticRowStatus to 'createAndGo'. The VLAN will be created in the device without tagged or untagged ports. A default VLAN name is assigned and the status is set to 'active'. To configure tagged and untagged port members of the VLAN, assign appropriate of dot1qVlanStaticTaggedPorts and dot1qVlanStaticUntaggedPorts. A set operation takes effect on the device immediately. To delete a VLAN, select the VID for dot1qVlanIndex and set dot1qVlanStaticRowStatus to 'destory'. The row and the corresponding VLAN configurarion will be removed from the device. VLAN 1 is the default VLAN and can never be deleted. All untagged traffic falls into this VLAN by default. 'createAndWait', 'notInService', 'notReady' have no effects. | ||||
| Ndot1qGvrp | 1.3.6.1.4.1.2882.2.1.1.5.2.3 | |||
| Sdot1qGvrpStatus | 1.3.6.1.4.1.2882.2.1.1.5.2.3.1 | INTEGER | RW | |
scalar · INTEGER · read-write · current Enable GVRP Protocol.
| ||||
| Tdot1qPortGvrpTable | 1.3.6.1.4.1.2882.2.1.1.5.2.3.2 | NA | ||
table · not-accessible · current A table containing per port control and status information for GVRP configuration in the device. | ||||
| Rdot1qPortGvrpEntry | 1.3.6.1.4.1.2882.2.1.1.5.2.3.2.1 | NA | ||
row · not-accessible · current Information controlling GVRP configuration for a port on the device.
| ||||
| Cdot1qPortGvrpIndex | 1.3.6.1.4.1.2882.2.1.1.5.2.3.2.1.1 | INTEGER | NA | |
column · INTEGER · not-accessible · current The port identifier. | ||||
| Cdot1qPortGvrpStatus | 1.3.6.1.4.1.2882.2.1.1.5.2.3.2.1.2 | INTEGER | RW | |
column · INTEGER · read-write · current The state of GVRP operation on this port. The value enabled(1) indicates that GVRP is enabled on this port, as long as dot1qGvrpStatus is also enabled for this device. When disabled(2) but dot1qGvrpStatus is still enabled for the device, GVRP is disabled on this port: any GVRP packets received will be silently discarded and no GVRP registrations will be propagated from other ports. This object affects all GVRP Applicant and Registrar state machines on this port. A transition from disabled(2) to enabled(1) will cause a reset of all GVRP state machines on this port.
| ||||
| Cdot1qPortGarpJoinTimer | 1.3.6.1.4.1.2882.2.1.1.5.2.3.2.1.3 | TimeInterval | RW | |
column · TimeInterval · read-write · current The GARP Join timer, in centiseconds. | ||||
| Cdot1qPortGarpLeaveTimer | 1.3.6.1.4.1.2882.2.1.1.5.2.3.2.1.4 | TimeInterval | RW | |
column · TimeInterval · read-write · current The GARP Leave time, in centiseconds. | ||||
| Cdot1qPortGarpLeaveAllTimer | 1.3.6.1.4.1.2882.2.1.1.5.2.3.2.1.5 | TimeInterval | RW | |
column · TimeInterval · read-write · current The GARP LeaveAll time, in centiseconds. | ||||
| Tdot1qVlanCurrentTable | 1.3.6.1.4.1.2882.2.1.1.5.2.4 | NA | ||
table · not-accessible · current A table containing information about currently configured VLANs, either by (local or network) management, or dynamically created as a result of GVRP requests received. | ||||
| Rdot1qVlanCurrentEntry | 1.3.6.1.4.1.2882.2.1.1.5.2.4.1 | NA | ||
row · not-accessible · current Information for a VLAN configured into the device by (local or network) management, or dynamically created as a result of GVRP requests received. | ||||
| Cdot1qVlanCurrentIndex | 1.3.6.1.4.1.2882.2.1.1.5.2.4.1.1 | INTEGER | RO | |
column · INTEGER · read-only · current The VLAN Identifier (VID) refering to this VLAN. | ||||
| Cdot1qVlanCurrentEgressPorts | 1.3.6.1.4.1.2882.2.1.1.5.2.4.1.2 | PortList | RO | |
column · PortList · read-only · current The set of ports which are transmitting traffic for this VLAN as either tagged or untagged frames. | ||||
| Cdot1qVlanCurrentUntaggedPorts | 1.3.6.1.4.1.2882.2.1.1.5.2.4.1.3 | PortList | RO | |
column · PortList · read-only · current The set of ports which are transmitting traffic for this VLAN as untagged frames. | ||||
| Cdot1qVlanStatus | 1.3.6.1.4.1.2882.2.1.1.5.2.4.1.4 | INTEGER | RO | |
column · INTEGER · read-only · current This object indicates the status of this entry.
other(1) - this entry is currently in use but the
conditions under which it will remain so differ
from the following values.
permanent(2) - this entry, corresponding to an entry
in dot1qVlanStaticTable, is currently in use and
will remain so after the next reset of the
device. The port lists for this entry include
ports from the equivalent dot1qVlanStaticTable
entry and ports learnt dynamically.
dynamicGvrp(3) - this entry is currently in use
and will remain so until removed by GVRP. There
is no static entry for this VLAN and it will be
removed when the last port leaves the VLAN.
| ||||
| Ndot1qTunnel | 1.3.6.1.4.1.2882.2.1.1.5.2.5 | |||
| Sdot1qTunnelEtherType | 1.3.6.1.4.1.2882.2.1.1.5.2.5.1 | OCTET STRING (SIZE (2)) | RW | |
scalar · OCTET STRING (SIZE (2)) · read-write · current ethertype/TPID | ||||
| Tdot1qTunnelPortTable | 1.3.6.1.4.1.2882.2.1.1.5.2.5.2 | NA | ||
table · not-accessible · current A table containing per tunnel access or uplink port information in the device. | ||||
| Rdot1qTunnelPortEntry | 1.3.6.1.4.1.2882.2.1.1.5.2.5.2.1 | NA | ||
row · not-accessible · current Information controlling tunnel configuration for a port on the device.
| ||||
| Cdot1qTunnelPortIndex | 1.3.6.1.4.1.2882.2.1.1.5.2.5.2.1.1 | INTEGER | NA | |
column · INTEGER · not-accessible · current The port identifier. | ||||
| Cdot1qTunnelPortMode | 1.3.6.1.4.1.2882.2.1.1.5.2.5.2.1.2 | INTEGER | RW | |
column · INTEGER · read-write · current Tunnel mode controls
| ||||
| NprivateVlan | 1.3.6.1.4.1.2882.2.1.1.5.3 | |||
| TprivateVlanIdTable | 1.3.6.1.4.1.2882.2.1.1.5.3.1 | NA | ||
table · not-accessible · current A table containing per Private VLAN ID information in the device. | ||||
| RprivateVlanIdEntry | 1.3.6.1.4.1.2882.2.1.1.5.3.1.1 | NA | ||
row · not-accessible · current Information controlling Private VLAN ID configuration on the device.
| ||||
| CprivateVlanId | 1.3.6.1.4.1.2882.2.1.1.5.3.1.1.1 | INTEGER | NA | |
column · INTEGER · not-accessible · current The Private VLAN ID. | ||||
| CprivateVlanIdType | 1.3.6.1.4.1.2882.2.1.1.5.3.1.1.2 | INTEGER | RW | |
column · INTEGER · read-write · current Private VLAN ID type controls
| ||||
| TprivateVlanPortTable | 1.3.6.1.4.1.2882.2.1.1.5.3.2 | NA | ||
table · not-accessible · current A table containing per Private VLAN Port information in the device. | ||||
| RprivateVlanPortEntry | 1.3.6.1.4.1.2882.2.1.1.5.3.2.1 | NA | ||
row · not-accessible · current Information controlling Private VLAN Port configuration on the device.
| ||||
| CprivateVlanPortIndex | 1.3.6.1.4.1.2882.2.1.1.5.3.2.1.1 | INTEGER | NA | |
column · INTEGER · not-accessible · current The Private Port Index. | ||||
| CprivateVlanPortMode | 1.3.6.1.4.1.2882.2.1.1.5.3.2.1.2 | INTEGER | RW | |
column · INTEGER · read-write · current Private VLAN Port mode controls
| ||||
| TprivateVlanHostAssociationTable | 1.3.6.1.4.1.2882.2.1.1.5.3.3 | NA | ||
table · not-accessible · current A table containing per Private VLAN host port association information in the device. | ||||
| RprivateVlanHostAssociationEntry | 1.3.6.1.4.1.2882.2.1.1.5.3.3.1 | NA | ||
row · not-accessible · current Information controlling Private VLAN host port association configuration on the device. | ||||
| CprivateVlanHostAssociationPortIndex | 1.3.6.1.4.1.2882.2.1.1.5.3.3.1.1 | INTEGER (1..10) | NA | |
column · INTEGER (1..10) · not-accessible · current The Private Host Port Index. | ||||
| CprivateVlanHostAssociationPrimaryVid | 1.3.6.1.4.1.2882.2.1.1.5.3.3.1.2 | INTEGER | RW | |
column · INTEGER · read-write · current Private VLAN host Port association primary VLAN ID. If enter 0 then clear setting. | ||||
| CprivateVlanHostAssociationSecondaryVid | 1.3.6.1.4.1.2882.2.1.1.5.3.3.1.3 | INTEGER | RW | |
column · INTEGER · read-write · current Private VLAN host Port association secondary VLAN ID(isolated/community). If enter 0 then clear setting. | ||||
| TprivateVlanMappingTable | 1.3.6.1.4.1.2882.2.1.1.5.3.4 | NA | ||
table · not-accessible · current A table containing per Private VLAN promiscuous port mapping information in the device. | ||||
| RprivateVlanMappingEntry | 1.3.6.1.4.1.2882.2.1.1.5.3.4.1 | NA | ||
row · not-accessible · current Information controlling Private VLAN promiscuous port mapping configuration on the device. | ||||
| CprivateVlanMappingPromiscuousPortIndex | 1.3.6.1.4.1.2882.2.1.1.5.3.4.1.1 | INTEGER (1..10) | NA | |
column · INTEGER (1..10) · not-accessible · current The Private Promiscuous Port Index. | ||||
| CprivateVlanMappingPrimaryVid | 1.3.6.1.4.1.2882.2.1.1.5.3.4.1.2 | INTEGER | RW | |
column · INTEGER · read-write · current Private VLAN promiscuous Port mapping primary VLAN ID. If enter 0 then clear setting. | ||||
| CprivateVlanMappingSecondaryVidList | 1.3.6.1.4.1.2882.2.1.1.5.3.4.1.3 | DisplayString (SIZE (0..64)) | RW | |
column · DisplayString (SIZE (0..64)) · read-write · current Private VLAN promiscuous Port mapping secondary VLAN ID list. If enter zero-length string then clear setting. | ||||
| NtrafficPrioritization | 1.3.6.1.4.1.2882.2.1.1.6 | |||
| SqosPolicy | 1.3.6.1.4.1.2882.2.1.1.6.1 | INTEGER | RW | |
scalar · INTEGER · read-write · current (1)8,4,2,1 weight round robin scheme: the switch will follow 8:4:2:1 rate to process priority queue from Hi to lowest queue. This approach prevents the lower priotiry packets from being starved out with only a slight delay to the higher priority packets. (2)Use the strict priority scheme: Queue with higher priority will always be process first, while queue with lower priority will only be processed when the higher priority queue is empty. This approach can cause the lower priorities the be startved out preventing them from transmitting any packets, but it ensures that all high priority packets serviced as soon as possible.
| ||||
| TqosPortDefaultCosTable | 1.3.6.1.4.1.2882.2.1.1.6.2 | NA | ||
table · not-accessible · current Table of descriptive information and configuration about port default cos value. | ||||
| RqosPortDefaultCosEntry | 1.3.6.1.4.1.2882.2.1.1.6.2.1 | NA | ||
row · not-accessible · current An entry in the table, containing inforamtion about port default cos value.
| ||||
| CqosPortNum | 1.3.6.1.4.1.2882.2.1.1.6.2.1.1 | Integer32 | RO | |
column · Integer32 · read-only · current Port number. | ||||
| CqosPortTrust | 1.3.6.1.4.1.2882.2.1.1.6.2.1.2 | INTEGER | RW | |
column · INTEGER · read-write · current Two kinds of priority information are token into
consideration when a packet is processed. One is COS,
the IEEE 802.3ac tag containing IEEE 802.1p priority
information, and the other is DSCP, the IPv4 Type of
Service/DiffServ field.
(1)COS only: the port priority will only follow the
COS priority that you have assigned.
(2)DSCP only: the port priority will only follow the
DSCP priority that you have assigned.
(3)COS first: the port priority will follow the COS
priority first, and then other priority rule.
(4)DSCP first: the port priority will follow the DSCP
priority first, and the other priority rule.
| ||||
| CqosPortDefaultCos | 1.3.6.1.4.1.2882.2.1.1.6.2.1.3 | Integer32 (0..7) | RW | |
column · Integer32 (0..7) · read-write · current The port priority will follow the default port priority | ||||
| TqosCOSTable | 1.3.6.1.4.1.2882.2.1.1.6.3 | NA | ||
table · not-accessible · current Table of descriptive information and configuration about COS QOS. | ||||
| RqosCOSEntry | 1.3.6.1.4.1.2882.2.1.1.6.3.1 | NA | ||
row · not-accessible · current An entry in the table, containing inforamtion about COS QOS.
| ||||
| CqosCOSPriority | 1.3.6.1.4.1.2882.2.1.1.6.3.1.1 | Integer32 (0..7) | RO | |
column · Integer32 (0..7) · read-only · current COS priority. | ||||
| CqosCOS | 1.3.6.1.4.1.2882.2.1.1.6.3.1.2 | INTEGER | RW | |
column · INTEGER · read-write · current The port priority will follow the COS priority that you have assigned (0)low, (1)middle, (2)high, or (3)highest.
| ||||
| TqosDscpTable | 1.3.6.1.4.1.2882.2.1.1.6.4 | NA | ||
table · not-accessible · current Table of descriptive information and configuration about DSCP QOS. | ||||
| RqosDscpEntry | 1.3.6.1.4.1.2882.2.1.1.6.4.1 | NA | ||
row · not-accessible · current An entry in the table, containing inforamtion about DSCP QOS.
| ||||
| CqosDscpPriority | 1.3.6.1.4.1.2882.2.1.1.6.4.1.1 | Integer32 (0..63) | RO | |
column · Integer32 (0..63) · read-only · current Dscp priority. | ||||
| CqosDscp | 1.3.6.1.4.1.2882.2.1.1.6.4.1.2 | INTEGER | RW | |
column · INTEGER · read-write · current The port priority will follow the Dscp priority that you have assigned (0)low (1)middle, (2)high, (3)highest.
| ||||
| NmulticastFiltering | 1.3.6.1.4.1.2882.2.1.1.7 | |||
| NigmpQuery | 1.3.6.1.4.1.2882.2.1.1.7.1 | |||
| SigmpQueryVersion | 1.3.6.1.4.1.2882.2.1.1.7.1.1 | INTEGER | RW | |
scalar · INTEGER · read-write · current (1)IGMP Query version 1. (2)IGMP Query version 2.
| ||||
| SigmpQueryStatus | 1.3.6.1.4.1.2882.2.1.1.7.1.2 | INTEGER | RW | |
scalar · INTEGER · read-write · current (1)enable IGMP Query on management vlan. (2)disable IGMP Query.
| ||||
| SigmpQueryInterval | 1.3.6.1.4.1.2882.2.1.1.7.1.3 | Integer32 (1..65535) | RW | |
scalar · Integer32 (1..65535) · read-write · current The interval between General Queries sent by this Querier in seconds. | ||||
| SigmpQueryMaxResponseTime | 1.3.6.1.4.1.2882.2.1.1.7.1.4 | Integer32 (1..25) | RW | |
scalar · Integer32 (1..25) · read-write · current Max Respocse Time is meaningful only in Membership Query messages, and specifies the maximum allowed time before sending a responding report in seconds. | ||||
| NigmpSnooping | 1.3.6.1.4.1.2882.2.1.1.7.2 | |||
| SigmpSnoopingStatus | 1.3.6.1.4.1.2882.2.1.1.7.2.1 | INTEGER | RW | |
scalar · INTEGER · read-write · current Parameter to enable or disable IGMP snooping on the device.
When enabled, the device will examine IGMP packets and set
up filters for multicast traffic.
The Internet Group Management Protocol (IGMP) is an internal
protocol of the Internet Protocol (IP) suite. IP manages
multicast traffic by using switches, routers, and hosts that
support IGMP. Enabling IGMP makes the device to gather
multicast group membership information by snooping IGMP
packets, which helps the device switch IP multicast traffic
to the ports where group members exist instead of flooding the
traffic to every ports.
IGMP have three fundamental types of message as follows:
Message Description
--------------------------------------------------------------
Query A message sent from the querier (IGMP router or switch)
asking for responses from each host belonging to a
multicast group.
Report A message sent by a host to the querier to indicate
that the host wants to be or is a member of a given
group indicated in the report message.
Leave A message sent by a host to the querier to indicate
that the host has quit to be a member for a specific
multicast group.
The IGMP snooping functionality is configured on a vlan basis.
To enable or disable IGMP snooping on vlans:
1. set igmpSnoopingStatus to enable(1) or disable(2).
2. specify on which vlan IGMP snooping works by configuring
each entries in the igmpSnoopingTable.
As a result, you can turn on or off IGMP snooping functionality
by setting igmpSnoopingStatus while keeping the configuration
for each vlan. Or you can turn on or off IGMP snooping for a
specific vlan in igmpSnoopingTable with the statuses on other
vlan untouched.
| ||||
| TigmpSnoopingTable | 1.3.6.1.4.1.2882.2.1.1.7.2.2 | NA | ||
table · not-accessible · current Table of descriptive information about on which vlan is IGMP snooping enabled. | ||||
| RigmpSnoopingEntry | 1.3.6.1.4.1.2882.2.1.1.7.2.2.1 | NA | ||
row · not-accessible · current Inforamtion enabling or disabling IGMP snooping on a vlan.
| ||||
| CigmpSnoopingEntryVID | 1.3.6.1.4.1.2882.2.1.1.7.2.2.1.1 | INTEGER | RO | |
column · INTEGER · read-only · current The vlan id. | ||||
| CigmpSnoopingEntryStatus | 1.3.6.1.4.1.2882.2.1.1.7.2.2.1.2 | INTEGER | RW | |
column · INTEGER · read-write · current The state of igmp snooping functionality on a vlan. Set to enabled(1) indicates that igmp snooping is enabled on the vlan. When igmpSnoopingStatus is also turned on, each IGMP packets on the vlan will be processed. When disabled(2) with igmpSnoopingStatus enabled, igmp packets will not be processed and be propagated to other member ports of the vlan. A transition from disabled(2) to enabled(1) will cause a reset of all igmp snooping information on this vlan.
| ||||
| TigmpSnoopingGroupTable | 1.3.6.1.4.1.2882.2.1.1.7.2.3 | NA | ||
table · not-accessible · current Table of descriptive information about IGMP snooped multicast groups. | ||||
| RigmpSnoopingGroupEntry | 1.3.6.1.4.1.2882.2.1.1.7.2.3.1 | NA | ||
row · not-accessible · current Information containing a multicast group and its member ports. | ||||
| CigmpSnoopingGroupEntryVID | 1.3.6.1.4.1.2882.2.1.1.7.2.3.1.1 | INTEGER | RO | |
column · INTEGER · read-only · current The VLAN ID of an IGMP entry. | ||||
| CigmpSnoopingGroupEntryIPAddr | 1.3.6.1.4.1.2882.2.1.1.7.2.3.1.2 | IpAddress | RO | |
column · IpAddress · read-only · current The multicast group IP address. | ||||
| CigmpSnoopingGroupEntryMembers | 1.3.6.1.4.1.2882.2.1.1.7.2.3.1.3 | PortList | RO | |
column · PortList · read-only · current The member ports of the group. | ||||
| NunknownMulticast | 1.3.6.1.4.1.2882.2.1.1.7.3 | |||
| SunknownMulticastStatus | 1.3.6.1.4.1.2882.2.1.1.7.3.1 | INTEGER | RW | |
scalar · INTEGER · read-write · current Select IGMP Unknown Multicast policy.
(1) Send to Query Ports: The device sends the packets with
an unknown MAC/IP Multicast address to query ports
(2) Discard: The device discards all packets with an unknown
MAC/IP Multicast address.
(3) Send to All Ports: The device sends the packets with
an unknown MAC/IP Multicast address to all ports.
| ||||
| Nsnmp | 1.3.6.1.4.1.2882.2.1.1.8 | |||
| TsnmpCommunityStringTable | 1.3.6.1.4.1.2882.2.1.1.8.1 | NA | ||
table · not-accessible · current Table of information configuring community strings of SNMP agent. An SNMP community string is a text string that acts as a password. It is used to authenticate messages that are sent between the management station (the SNMP manager) and the device (the SNMP agent). The community string is included in every packet that is transmitted between the SNMP manager and the SNMP agent. After receiving an SNMP request, the SNMP agent compares the community string in the request to the community strings that are configured for the agent. The requests are valid under these circumstances: - Only SNMP Get and Get-next requests are valid if the community string in the request matches the read-only community. - SNMP Get, Get-next, and Set requests are valid if the community string in the request matches the agent's read-write community. By default, 'public' is the read-only community and 'private' is the read-write community. Total 4 community strings are allowed to configure in the device. | ||||
| RsnmpCommunityStringEntry | 1.3.6.1.4.1.2882.2.1.1.8.1.1 | NA | ||
row · not-accessible · current Inforamtion configuring an community string. | ||||
| CsnmpCommunityStringIndex | 1.3.6.1.4.1.2882.2.1.1.8.1.1.1 | Integer32 | NA | |
column · Integer32 · not-accessible · current Index of community string. | ||||
| CsnmpCommunityStringName | 1.3.6.1.4.1.2882.2.1.1.8.1.1.2 | DisplayString (SIZE (0..32)) | RW | |
column · DisplayString (SIZE (0..32)) · read-write · current A community string with maximum 32 characters. | ||||
| CsnmpCommunityStringPrivilege | 1.3.6.1.4.1.2882.2.1.1.8.1.1.3 | INTEGER | RW | |
column · INTEGER · read-write · current The access privilege of the community string.
| ||||
| CsnmpCommunityStringStatus | 1.3.6.1.4.1.2882.2.1.1.8.1.1.4 | RowStatus | RC | |
column · RowStatus · read-create · current The status of this entry. Set to (5)createAndWait to create a new entry. A new entry or an active entry can be edited. Once an entry is modified, its status becomes (3)notReady. Set to (1)active to apply the modification to the switch. An entry can be removed by setting to (6)destory. | ||||
| TsnmpV3UserTable | 1.3.6.1.4.1.2882.2.1.1.8.2 | NA | ||
table · not-accessible · current Table of descriptive and information about trap servers. A trap server is the recipient of an SNMP trap. The device does not send a trap unless it knows to which station it should send a trap. | ||||
| RsnmpV3UserEntry | 1.3.6.1.4.1.2882.2.1.1.8.2.1 | NA | ||
row · not-accessible · current An entry in the table, containing inforamtion about a trap server of SNMP agent.
| ||||
| CsnmpV3UserIndex | 1.3.6.1.4.1.2882.2.1.1.8.2.1.1 | Integer32 | NA | |
column · Integer32 · not-accessible · current Index of snmp v3 user. | ||||
| CsnmpV3UserName | 1.3.6.1.4.1.2882.2.1.1.8.2.1.2 | DisplayString | RW | |
| CsnmpV3UserSecurityLevel | 1.3.6.1.4.1.2882.2.1.1.8.2.1.3 | INTEGER | RW | |
column · INTEGER · read-write · current Specifiy the authentication and privacy level
- noauth(1) no authentication and no privacy.
- auth(2) enables MD5 or SHA packet authentication.
- priv(3) enables MD5 or SHA packet authentication
and DES packet encryption.
| ||||
| CsnmpV3UserAuthProtocol | 1.3.6.1.4.1.2882.2.1.1.8.2.1.4 | INTEGER | RW | |
column · INTEGER · read-write · current MD5(Message Digest 5) or SHA (Secure Hash Algorithm)
| ||||
| CsnmpV3UserAuthPassword | 1.3.6.1.4.1.2882.2.1.1.8.2.1.5 | DisplayString | RW | |
| CsnmpV3UserDesPassword | 1.3.6.1.4.1.2882.2.1.1.8.2.1.6 | DisplayString | RW | |
| CsnmpV3UserStatus | 1.3.6.1.4.1.2882.2.1.1.8.2.1.7 | RowStatus | RC | |
| SsnmpTrapServerEnable | 1.3.6.1.4.1.2882.2.1.1.8.3 | INTEGER | RW | |
scalar · INTEGER · read-write · current To enable, disable snmp trap functionality. SNMPv1 traps are defined in RFC 1157, and SNMPv2c trap is defined as NOTIFICATION. SNMP traps enable this device to notify the management station of significant events by way of an unsolicited SNMP message. After the manager receives the event, the manager displays it and can choose to take an action based on the event. For instance, the manager can poll the agent directly, or poll other associated device agents to get a better understanding of the event.
| ||||
| TsnmpTrapServerTable | 1.3.6.1.4.1.2882.2.1.1.8.4 | NA | ||
table · not-accessible · current Table of descriptive and information about trap servers. A trap server is the recipient of an SNMP trap. The device does not send a trap unless it knows to which station it should send a trap. | ||||
| RsnmpTrapServerEntry | 1.3.6.1.4.1.2882.2.1.1.8.4.1 | NA | ||
row · not-accessible · current An entry in the table, containing inforamtion about a trap server of SNMP agent.
| ||||
| CsnmpTrapServerIndex | 1.3.6.1.4.1.2882.2.1.1.8.4.1.1 | Integer32 | NA | |
column · Integer32 · not-accessible · current Index of trap server. | ||||
| CsnmpTrapServerIPAddr | 1.3.6.1.4.1.2882.2.1.1.8.4.1.2 | IpAddress | RW | |
column · IpAddress · read-write · current Trap Server IP Address. | ||||
| CsnmpTrapServerTrapComm | 1.3.6.1.4.1.2882.2.1.1.8.4.1.3 | DisplayString (SIZE (0..32)) | RW | |
column · DisplayString (SIZE (0..32)) · read-write · current The community string of trap server. The password-like string will be sent with the notification operation. | ||||
| CsnmpTrapServerTrapVer | 1.3.6.1.4.1.2882.2.1.1.8.4.1.4 | INTEGER | RW | |
column · INTEGER · read-write · current The trap version.
| ||||
| CsnmpTrapServerStatus | 1.3.6.1.4.1.2882.2.1.1.8.4.1.5 | RowStatus | RC | |
column · RowStatus · read-create · current The status of this entry. Set to (5)createAndWait to create a new entry. A new entry or an active entry can be edited. Once an entry is modified, its status becomes (3)notReady. Set to (1)active to apply the modification to the device. An entry can be removed by setting to (6)destory. | ||||
| Nsecurity | 1.3.6.1.4.1.2882.2.1.1.9 | |||
| NportSecurity | 1.3.6.1.4.1.2882.2.1.1.9.1 | |||
| TportSecurityStatusTable | 1.3.6.1.4.1.2882.2.1.1.9.1.1 | NA | ||
table · not-accessible · current A table containing information about port security status on each port. Port security prevents a port from address learning. Only those MAC addresses that are configured by management are allowed to access the switch or transmit/receive through the port. Upto 10 MAC addresses can assigned to each port by adding address entries to portSecurityMacTable or macAddrTable. If the port security functionality is enabled but without any MAC address configured on a port, no traffic can access the switch or transmit/receive from the port. | ||||
| RportSecurityStatusEntry | 1.3.6.1.4.1.2882.2.1.1.9.1.1.1 | NA | ||
row · not-accessible · current An entry configuring port security for a port. | ||||
| CportSecurityPortIndex | 1.3.6.1.4.1.2882.2.1.1.9.1.1.1.1 | Integer32 | NA | |
column · Integer32 · not-accessible · current The port id. | ||||
| CportSecurityPortStatus | 1.3.6.1.4.1.2882.2.1.1.9.1.1.1.2 | INTEGER | RW | |
column · INTEGER · read-write · current (1)enable port security on this port. (2)disable port security on this port.
| ||||
| TportSecurityMacTable | 1.3.6.1.4.1.2882.2.1.1.9.1.2 | NA | ||
table · not-accessible · current Table configuring static unicast MAC address for each port. When you add a static MAC address, it remains in the switch's address table, regardless of whether the device is physically connected to the switch. With enabling port security in portSecurityStatusTable, only those MAC addresses configured in portSecurityMacTable are allowed to access the switch or transmit/receive through the port. | ||||
| RportSecurityMacEntry | 1.3.6.1.4.1.2882.2.1.1.9.1.2.1 | NA | ||
row · not-accessible · current An entry configuring a static unicast MAC addresses on a port.
| ||||
| CportSecurityMacIndex | 1.3.6.1.4.1.2882.2.1.1.9.1.2.1.1 | Integer32 | NA | |
column · Integer32 · not-accessible · current Index of MAC. | ||||
| CportSecurityPort | 1.3.6.1.4.1.2882.2.1.1.9.1.2.1.2 | Integer32 | RW | |
column · Integer32 · read-write · current The port id. | ||||
| CportSecurityVlanIndex | 1.3.6.1.4.1.2882.2.1.1.9.1.2.1.3 | Integer32 | RW | |
column · Integer32 · read-write · current The vlan id where the MAC address belongs to. | ||||
| CportSecurityMac | 1.3.6.1.4.1.2882.2.1.1.9.1.2.1.4 | MacAddress | RW | |
column · MacAddress · read-write · current MAC address of the entry. | ||||
| CportSecurityMacStatus | 1.3.6.1.4.1.2882.2.1.1.9.1.2.1.5 | RowStatus | RC | |
column · RowStatus · read-create · current The status of this entry. Set to (5)createAndWait to create a new entry. A new entry or an active entry can be edited. Once an entry is modified, its status becomes (3)notReady. Set to (1)active to apply the modification to the device. An entry can be removed by setting to (6)destory. | ||||
| NipSecurity | 1.3.6.1.4.1.2882.2.1.1.9.2 | |||
| SipSecurityStatus | 1.3.6.1.4.1.2882.2.1.1.9.2.1 | INTEGER | RW | |
scalar · INTEGER · read-write · current Enable or disable IP security functionality. IP security allows you to assign specific IP addresses that are permitted to access the device for securing switch management. Set to (1) to enable IP Security. set to (2) to disable IP Security. Enabling IP Security without any entries configured in the ipSecurityTable has no effect on the access traffic.
| ||||
| TipSecurityTable | 1.3.6.1.4.1.2882.2.1.1.9.2.2 | NA | ||
table · not-accessible · current Table configuring IP addresses that can access and manage the device through network, such as telnet, web or SNMP. Please note that enabling IP security function but without adding the IP address of your current management station will break current management connection. | ||||
| RipSecurityEntry | 1.3.6.1.4.1.2882.2.1.1.9.2.2.1 | NA | ||
| CipSecurityIndex | 1.3.6.1.4.1.2882.2.1.1.9.2.2.1.1 | Integer32 (1..10) | NA | |
column · Integer32 (1..10) · not-accessible · current Index of IP address entry. | ||||
| CipSecurityIP | 1.3.6.1.4.1.2882.2.1.1.9.2.2.1.2 | IpAddress | RW | |
column · IpAddress · read-write · current An IP address that can access and manage the device. | ||||
| CipSecurityRowStatus | 1.3.6.1.4.1.2882.2.1.1.9.2.2.1.3 | RowStatus | RC | |
column · RowStatus · read-create · current This object is used to manage to creation and deletion of a authorized IP address, and is used to indicate the status of this entry. A empty entry or an active entry can be edited. Once an entry is modified, its status becomes (3)notReady. Set to (1)active to apply the modification to the device. An entry can be removed by setting to (6)destory. | ||||
| Ndot1x | 1.3.6.1.4.1.2882.2.1.1.9.3 | |||
| Sdot1xStatus | 1.3.6.1.4.1.2882.2.1.1.9.3.1 | INTEGER | RW | |
scalar · INTEGER · read-write · current IEEE802.1x protocol function status. (1) IEEE802.1x protocol function is enabled. (2) IEEE802.1x protocol function is disabled. 802.1x makes use of the physical access characteristics of IEEE802 LAN infrastructures in order to provide a means of authenticating and authorizing devices attached to a LAN port that has point-to-point connection characteristics, and of preventing access to that port in cases in which the authentication and authorization process fails.
| ||||
| Sdot1xAuthentication | 1.3.6.1.4.1.2882.2.1.1.9.3.2 | INTEGER | RW | |
scalar · INTEGER · read-write · current .
| ||||
| TradiusServerTable | 1.3.6.1.4.1.2882.2.1.1.9.3.3 | NA | ||
table · not-accessible · current . | ||||
| RradiusServerEntry | 1.3.6.1.4.1.2882.2.1.1.9.3.3.1 | NA | ||
| CradiusServerIndex | 1.3.6.1.4.1.2882.2.1.1.9.3.3.1.1 | Integer32 | NA | |
column · Integer32 · not-accessible · current Index of Radius server configuration. | ||||
| CradiusServerIp | 1.3.6.1.4.1.2882.2.1.1.9.3.3.1.2 | IpAddress | RW | |
column · IpAddress · read-write · current IP address of this radius server. | ||||
| CradiusServerServerPort | 1.3.6.1.4.1.2882.2.1.1.9.3.3.1.3 | Integer32 | RW | |
column · Integer32 · read-write · current The UDP port number used by the authentication server to authenticate. | ||||
| CradiusServerAccountingPort | 1.3.6.1.4.1.2882.2.1.1.9.3.3.1.4 | Integer32 | RW | |
column · Integer32 · read-write · current Accounting Port: The UDP port number used by the authentication server to retrieve accounting information. | ||||
| CradiusServerSharedKey | 1.3.6.1.4.1.2882.2.1.1.9.3.3.1.5 | DisplayString | RW | |
column · DisplayString · read-write · current A key shared between this switch and authentication server. | ||||
| Tdot1xLocalUserTable | 1.3.6.1.4.1.2882.2.1.1.9.3.4 | NA | ||
table · not-accessible · current . | ||||
| Rdot1xLocalUserEntry | 1.3.6.1.4.1.2882.2.1.1.9.3.4.1 | NA | ||
| Cdot1xLocalUserIndex | 1.3.6.1.4.1.2882.2.1.1.9.3.4.1.1 | Integer32 | NA | |
column · Integer32 · not-accessible · current . | ||||
| Cdot1xLocalUserName | 1.3.6.1.4.1.2882.2.1.1.9.3.4.1.2 | DisplayString | RW | |
column · DisplayString · read-write · current set this field to empty to remove this user config. | ||||
| Cdot1xLocalUserPassword | 1.3.6.1.4.1.2882.2.1.1.9.3.4.1.3 | DisplayString | RW | |
column · DisplayString · read-write · current . | ||||
| Cdot1xLocalUserVid | 1.3.6.1.4.1.2882.2.1.1.9.3.4.1.4 | Integer32 | RW | |
column · Integer32 · read-write · current . | ||||
| Tdot1xPortConfigTable | 1.3.6.1.4.1.2882.2.1.1.9.3.5 | NA | ||
table · not-accessible · current . | ||||
| Rdot1xPortConfigEntry | 1.3.6.1.4.1.2882.2.1.1.9.3.5.1 | NA | ||
| Cdot1xPortConfigIndex | 1.3.6.1.4.1.2882.2.1.1.9.3.5.1.1 | Integer32 | NA | |
column · Integer32 · not-accessible · current . | ||||
| Cdot1xPortAuthControl | 1.3.6.1.4.1.2882.2.1.1.9.3.5.1.2 | INTEGER | RW | |
column · INTEGER · read-write · current .
| ||||
| Cdot1xPortReauthentication | 1.3.6.1.4.1.2882.2.1.1.9.3.5.1.3 | INTEGER | RW | |
column · INTEGER · read-write · current .
| ||||
| Cdot1xPortMaxRequest | 1.3.6.1.4.1.2882.2.1.1.9.3.5.1.4 | INTEGER | RW | |
column · INTEGER · read-write · current . | ||||
| Cdot1xPortGuestVlan | 1.3.6.1.4.1.2882.2.1.1.9.3.5.1.5 | INTEGER | RW | |
column · INTEGER · read-write · current . | ||||
| Cdot1xPortHostMode | 1.3.6.1.4.1.2882.2.1.1.9.3.5.1.6 | INTEGER | RW | |
column · INTEGER · read-write · current .
| ||||
| Cdot1xPortAdminDirection | 1.3.6.1.4.1.2882.2.1.1.9.3.5.1.7 | INTEGER | RW | |
column · INTEGER · read-write · current .
| ||||
| Cdot1xPortConfigSetDefault | 1.3.6.1.4.1.2882.2.1.1.9.3.5.1.8 | INTEGER | RW | |
column · INTEGER · read-write · current .
| ||||
| Cdot1xPortReinitialize | 1.3.6.1.4.1.2882.2.1.1.9.3.5.1.9 | INTEGER | RW | |
column · INTEGER · read-write · current .
| ||||
| Cdot1xPortClientReauth | 1.3.6.1.4.1.2882.2.1.1.9.3.5.1.10 | INTEGER | WO | |
column · INTEGER · write-only · current .
| ||||
| Tdot1xPortTimeoutConfigTable | 1.3.6.1.4.1.2882.2.1.1.9.3.6 | NA | ||
table · not-accessible · current . | ||||
| Rdot1xPortTimeoutConfigEntry | 1.3.6.1.4.1.2882.2.1.1.9.3.6.1 | NA | ||
| Cdot1xPortTimeoutIndex | 1.3.6.1.4.1.2882.2.1.1.9.3.6.1.1 | Integer32 | NA | |
column · Integer32 · not-accessible · current . | ||||
| Cdot1xPortReauthPeriod | 1.3.6.1.4.1.2882.2.1.1.9.3.6.1.2 | Integer32 | RW | |
column · Integer32 · read-write · current . | ||||
| Cdot1xPortQuietPeriod | 1.3.6.1.4.1.2882.2.1.1.9.3.6.1.3 | Integer32 | RW | |
column · Integer32 · read-write · current . | ||||
| Cdot1xPortTxPeriod | 1.3.6.1.4.1.2882.2.1.1.9.3.6.1.4 | Integer32 | RW | |
column · Integer32 · read-write · current . | ||||
| Cdot1xPortSupplicantTimeout | 1.3.6.1.4.1.2882.2.1.1.9.3.6.1.5 | Integer32 | RW | |
column · Integer32 · read-write · current . | ||||
| Cdot1xPortServerTimeout | 1.3.6.1.4.1.2882.2.1.1.9.3.6.1.6 | Integer32 | RW | |
column · Integer32 · read-write · current . | ||||
| Tdot1xPortStatusTable | 1.3.6.1.4.1.2882.2.1.1.9.3.7 | NA | ||
table · not-accessible · current . | ||||
| Rdot1xPortStatusEntry | 1.3.6.1.4.1.2882.2.1.1.9.3.7.1 | NA | ||
| Cdot1xPortStatusIndex | 1.3.6.1.4.1.2882.2.1.1.9.3.7.1.1 | Integer32 | NA | |
column · Integer32 · not-accessible · current . | ||||
| Cdot1xPortCtrl | 1.3.6.1.4.1.2882.2.1.1.9.3.7.1.2 | INTEGER | RO | |
column · INTEGER · read-only · current .
| ||||
| Cdot1xPortAuthStatus | 1.3.6.1.4.1.2882.2.1.1.9.3.7.1.3 | INTEGER | RO | |
column · INTEGER · read-only · current .
| ||||
| Cdot1xPortAuthSupplicant | 1.3.6.1.4.1.2882.2.1.1.9.3.7.1.4 | MacAddress | RO | |
column · MacAddress · read-only · current . | ||||
| Cdot1xPortOperDirection | 1.3.6.1.4.1.2882.2.1.1.9.3.7.1.5 | INTEGER | RO | |
column · INTEGER · read-only · current .
| ||||
| Nwarning | 1.3.6.1.4.1.2882.2.1.1.10 | |||
| NfaultRelay | 1.3.6.1.4.1.2882.2.1.1.10.1 | |||
| TfaultRelayTable | 1.3.6.1.4.1.2882.2.1.1.10.1.1 | NA | ||
table · not-accessible · current Table of configuration about fault relay. A fault relay is able to control an output circuit which is triggered by management defined fault events. There are two fault relays in the device, each is controlled by an faultRelayEntry in this table. To configure a fault relay, first select the type of fault event which will trigger the relay in faultSelection, and then configure the related column. Set faultRelayEntryStatus to active(1) to set the configuration to the device. | ||||
| RfaultRelayEntry | 1.3.6.1.4.1.2882.2.1.1.10.1.1.1 | NA | ||
| CfaultRelayId | 1.3.6.1.4.1.2882.2.1.1.10.1.1.1.1 | INTEGER | RO | |
column · INTEGER · read-only · current Index of fault relay.
| ||||
| CfaultSelection | 1.3.6.1.4.1.2882.2.1.1.10.1.1.1.2 | INTEGER | RW | |
column · INTEGER · read-write · current Select the type of fault event that triggers the relay. To config a fault relay, first select the founction this relay serves for, then configure the condition that triggers the relay in detail. At last, set the faultRelayEntryStatus to active(1) or nonActive(3) to enable or disable the setting on the relay.
| ||||
| CdiConfig | 1.3.6.1.4.1.2882.2.1.1.10.1.1.1.3 | INTEGER | RW | |
column · INTEGER · read-write · current The fault relay will be triggered if digital input is low or high.
| ||||
| CdryOutputOnPeriodConfig | 1.3.6.1.4.1.2882.2.1.1.10.1.1.1.4 | INTEGER (1..1000) | RW | |
column · INTEGER (1..1000) · read-write · current The fault relay will be closed after a period (in seconds). Together with dryOutputOffPeriodConfig, the fault relay can be configured to continue on and off. | ||||
| CdryOutputOffPeriodConfig | 1.3.6.1.4.1.2882.2.1.1.10.1.1.1.5 | INTEGER (1..1000) | RW | |
column · INTEGER (1..1000) · read-write · current The fault relay will be opened after a period (in seconds). Together with dryOutputOnPeriodConfig, the fault relay can be configured to continue on and off. | ||||
| CpowerFailureConfig | 1.3.6.1.4.1.2882.2.1.1.10.1.1.1.6 | INTEGER | RW | |
column · INTEGER · read-write · current The fault relay will be triggered if the configured power fails. Any means either power 1 or power2 fails
| ||||
| ClinkFailureConfig | 1.3.6.1.4.1.2882.2.1.1.10.1.1.1.7 | PortList | RW | |
column · PortList · read-write · current The fault relay will be trigger if any of the configured links fails. | ||||
| CpingFailureIP | 1.3.6.1.4.1.2882.2.1.1.10.1.1.1.8 | IpAddress | RW | |
column · IpAddress · read-write · current The fault relay will be trigger if fail to ping the assigned IP address. | ||||
| CpingResetTime | 1.3.6.1.4.1.2882.2.1.1.10.1.1.1.9 | INTEGER | RW | |
column · INTEGER · read-write · current Reset the ping process after pingResetTime, and then wait pingHoldTime to ping again. (optional) | ||||
| CpingHoldTime | 1.3.6.1.4.1.2882.2.1.1.10.1.1.1.10 | INTEGER | RW | |
column · INTEGER · read-write · current Reset the ping process after pingResetTime, and then wait pingHoldTime to ping again. (optional) | ||||
| CfaultRelayEntryStatus | 1.3.6.1.4.1.2882.2.1.1.10.1.1.1.11 | INTEGER | RW | |
column · INTEGER · read-write · current Setting this object to active(1) to save the configuration to the device. Setting this object to notActive(3) disable the configuration. The system returns active(1) or notActive when the settings of the entry is enabled or disabled on the relay. And the status becomes configuring(2) when the settings of the entry are modified and not set to active(1) yet.
| ||||
| NeventAndEmailWarning | 1.3.6.1.4.1.2882.2.1.1.10.2 | |||
| NeventSelection | 1.3.6.1.4.1.2882.2.1.1.10.2.1 | |||
| TsystemEventTable | 1.3.6.1.4.1.2882.2.1.1.10.2.1.1 | NA | ||
table · not-accessible · current Table of descriptive information and controls the reactions to system events. Three types of reactions will be triggered: (1)logging in the switch or send logs to remote syslog servers, (2)sending an email, or (3)send an snmp trap. Each type of alert is configured in sysLogConfiguration, smtpConfiguration, snmpTrapServerEnable and snmpTrapServerTable. | ||||
| RsystemEventEntry | 1.3.6.1.4.1.2882.2.1.1.10.2.1.1.1 | RO | ||
| CeventSystemEventIndex | 1.3.6.1.4.1.2882.2.1.1.10.2.1.1.1.1 | Integer32 | NA | |
column · Integer32 · not-accessible · current Index of events. | ||||
| CeventDeviceColdStartEvent | 1.3.6.1.4.1.2882.2.1.1.10.2.1.1.1.2 | AlertType | RW | |
column · AlertType · read-write · current Select which warning machanism to take place when the device cold starts. | ||||
| CeventDeviceWarmStartEvent | 1.3.6.1.4.1.2882.2.1.1.10.2.1.1.1.3 | AlertType | RW | |
column · AlertType · read-write · current Select which warning machanism to take place when the device warm starts. | ||||
| CeventAuthenticationFailureEvent | 1.3.6.1.4.1.2882.2.1.1.10.2.1.1.1.4 | AlertType | RW | |
column · AlertType · read-write · current Select which warning machanism to take place when authentication failure. | ||||
| CeventRingEvent | 1.3.6.1.4.1.2882.2.1.1.10.2.1.1.1.5 | AlertType | RW | |
column · AlertType · read-write · current Select which warning machanism to take place when ring event occured. | ||||
| CeventPower1FailureEvent | 1.3.6.1.4.1.2882.2.1.1.10.2.1.1.1.6 | AlertType | RW | |
column · AlertType · read-write · current Select which warning machanism to take place when power1 failure. | ||||
| CeventPower2FailureEvent | 1.3.6.1.4.1.2882.2.1.1.10.2.1.1.1.7 | AlertType | RW | |
column · AlertType · read-write · current Select which warning machanism to take place when power2 failure. | ||||
| CeventFaultRelayEvent | 1.3.6.1.4.1.2882.2.1.1.10.2.1.1.1.8 | AlertType | RW | |
column · AlertType · read-write · current Select which warning machanism to take place when a fault relay is triggered. | ||||
| CeventTimeSynchronizeEvent | 1.3.6.1.4.1.2882.2.1.1.10.2.1.1.1.9 | AlertType | RW | |
column · AlertType · read-write · current Select which warning machanism to take place when time synchronizatonn failed. | ||||
| CeventSFPEvent | 1.3.6.1.4.1.2882.2.1.1.10.2.1.1.1.10 | AlertType | RW | |
column · AlertType · read-write · current Select which warning machanism to take place when SFP event occured. | ||||
| CeventDI1ChangeEvent | 1.3.6.1.4.1.2882.2.1.1.10.2.1.1.1.11 | AlertType | RW | |
column · AlertType · read-write · current Select which warning machanism to take place when DI1 changed . | ||||
| CeventDI2ChangeEvent | 1.3.6.1.4.1.2882.2.1.1.10.2.1.1.1.12 | AlertType | RW | |
column · AlertType · read-write · current Select which warning machanism to take place when DI2 changed . | ||||
| CeventLoopDetectionEvent | 1.3.6.1.4.1.2882.2.1.1.10.2.1.1.1.13 | AlertType | RW | |
column · AlertType · read-write · current Select which warning machanism to take place when loop detection event occured. | ||||
| TportEventTable | 1.3.6.1.4.1.2882.2.1.1.10.2.1.2 | NA | ||
table · not-accessible · current Table of descriptive information and controls the reactions to port link up, link down, or both link up and down. Three types of reactions will be triggered: (1)logging in the switch or send logs to remote syslog servers, (2)sending an email, or (3)send an snmp trap. Each type of alert is configured in sysLogConfiguration, smtpConfiguration, snmpTrapServerEnable and snmpTrapServerTable. | ||||
| RportEventEntry | 1.3.6.1.4.1.2882.2.1.1.10.2.1.2.1 | NA | ||
| CeventPortNumber | 1.3.6.1.4.1.2882.2.1.1.10.2.1.2.1.1 | Integer32 | RO | |
column · Integer32 · read-only · current Port number. | ||||
| CeventPortEvent | 1.3.6.1.4.1.2882.2.1.1.10.2.1.2.1.2 | INTEGER | RW | |
column · INTEGER · read-write · current Select the port event to react to.
| ||||
| NsysLogConfiguration | 1.3.6.1.4.1.2882.2.1.1.10.2.2 | |||
| SsysLogLocalStatus | 1.3.6.1.4.1.2882.2.1.1.10.2.2.1 | INTEGER | RW | |
scalar · INTEGER · read-write · current Parameter to configure if the log should to be kept in the device or not.
| ||||
| SsysLogRemoteStatus | 1.3.6.1.4.1.2882.2.1.1.10.2.2.2 | INTEGER | RW | |
scalar · INTEGER · read-write · current Parameter to configure the log should be sent to a syslog server specified in sysLogServerAddr or not. When disabled or sysLogServerAddr is 0, the device will not send out or record any log.
| ||||
| SsysLogServerAddr | 1.3.6.1.4.1.2882.2.1.1.10.2.2.3 | IpAddress | RW | |
scalar · IpAddress · read-write · current The IP address of syslog server. | ||||
| NsmtpConfiguration | 1.3.6.1.4.1.2882.2.1.1.10.2.3 | |||
| SeventEmailAlertStatus | 1.3.6.1.4.1.2882.2.1.1.10.2.3.1 | INTEGER | RW | |
scalar · INTEGER · read-write · current Parameter to enable the email alert feature, When enabled, the switch will send an email to the address presented in emailAlertRcptTable.
| ||||
| SeventEmailAlertServer | 1.3.6.1.4.1.2882.2.1.1.10.2.3.2 | IpAddress | RW | |
scalar · IpAddress · read-write · current The IP address of SMTP server. It can't be modified when eventEmailAlertStatus is disabled. | ||||
| SeventEmailAlertAccount | 1.3.6.1.4.1.2882.2.1.1.10.2.3.3 | DisplayString (SIZE (0..70)) | RW | |
scalar · DisplayString (SIZE (0..70)) · read-write · current The email account for SMTP server. It can't be modified when eventEmailAlertAuthentication is disabled. | ||||
| SeventEmailAlertAuthentication | 1.3.6.1.4.1.2882.2.1.1.10.2.3.4 | INTEGER | RW | |
scalar · INTEGER · read-write · current Set to (1)enabled if it needs authentication to connect to the SMTP server. It can't be modified when eventEmailAlertStatus is disabled.
| ||||
| SeventEmailAlertUser | 1.3.6.1.4.1.2882.2.1.1.10.2.3.5 | DisplayString (SIZE (0..70)) | RW | |
scalar · DisplayString (SIZE (0..70)) · read-write · current The email account for SMTP server. It can't be modified when eventEmailAlertAuthentication is disabled. | ||||
| SeventEmailAlertPassword | 1.3.6.1.4.1.2882.2.1.1.10.2.3.6 | DisplayString (SIZE (0..36)) | WO | |
scalar · DisplayString (SIZE (0..36)) · write-only · current The password of email account. It can't be modified when eventEmailAlertAuthentication is disabled. | ||||
| TemailAlertRcptTable | 1.3.6.1.4.1.2882.2.1.1.10.2.3.7 | NA | ||
table · not-accessible · current Table configuring recipient email addresses. | ||||
| RemailAlertRcptEntry | 1.3.6.1.4.1.2882.2.1.1.10.2.3.7.1 | NA | ||
row · not-accessible · current An entry containing recipient email address. | ||||
| CeventEmailAlertRcptIndex | 1.3.6.1.4.1.2882.2.1.1.10.2.3.7.1.1 | Integer32 | NA | |
column · Integer32 · not-accessible · current Index of recipient Email address. | ||||
| CeventEmailAlertRcptEmailAddr | 1.3.6.1.4.1.2882.2.1.1.10.2.3.7.1.2 | DisplayString (SIZE (0..48)) | RW | |
column · DisplayString (SIZE (0..48)) · read-write · current A recipient email address. | ||||
| NhardwareStatus | 1.3.6.1.4.1.2882.2.1.1.10.3 | |||
| ThardwareStatusTable | 1.3.6.1.4.1.2882.2.1.1.10.3.1 | NA | ||
| RhardwareStatusEntry | 1.3.6.1.4.1.2882.2.1.1.10.3.1.1 | RO | ||
row · read-only · current | ||||
| CledHardwareStatusIndex | 1.3.6.1.4.1.2882.2.1.1.10.3.1.1.1 | Integer32 | NA | |
column · Integer32 · not-accessible · current Index of leds. | ||||
| CledPower1Status | 1.3.6.1.4.1.2882.2.1.1.10.3.1.1.2 | INTEGER | RO | |
column · INTEGER · read-only · current
| ||||
| CledPower2Status | 1.3.6.1.4.1.2882.2.1.1.10.3.1.1.3 | INTEGER | RO | |
column · INTEGER · read-only · current
| ||||
| CledDO1Status | 1.3.6.1.4.1.2882.2.1.1.10.3.1.1.4 | INTEGER | RO | |
column · INTEGER · read-only · current
| ||||
| CledDO2Status | 1.3.6.1.4.1.2882.2.1.1.10.3.1.1.5 | INTEGER | RO | |
column · INTEGER · read-only · current
| ||||
| CledDI1Status | 1.3.6.1.4.1.2882.2.1.1.10.3.1.1.6 | INTEGER | RO | |
column · INTEGER · read-only · current
| ||||
| CledDI2Status | 1.3.6.1.4.1.2882.2.1.1.10.3.1.1.7 | INTEGER | RO | |
column · INTEGER · read-only · current
| ||||
| CledRMStatus | 1.3.6.1.4.1.2882.2.1.1.10.3.1.1.8 | INTEGER | RO | |
column · INTEGER · read-only · current
| ||||
| NmonitorandDiag | 1.3.6.1.4.1.2882.2.1.1.11 | |||
| NmacAddressTable | 1.3.6.1.4.1.2882.2.1.1.11.1 | |||
| TmacAddrTable | 1.3.6.1.4.1.2882.2.1.1.11.1.1 | NA | ||
table · not-accessible · current A table containing information about unicast or multicast MAC addresses that currently learned, configured by management or IGMP snooping. | ||||
| RmacAddrEntry | 1.3.6.1.4.1.2882.2.1.1.11.1.1.1 | NA | ||
row · not-accessible · current An entry containing inforamtion about a MAC address entry.
| ||||
| CmacAddressAddr | 1.3.6.1.4.1.2882.2.1.1.11.1.1.1.1 | MacAddress | RW | |
column · MacAddress · read-write · current MAC address of the entry. | ||||
| CmacAddressType | 1.3.6.1.4.1.2882.2.1.1.11.1.1.1.2 | INTEGER | RW | |
column · INTEGER · read-write · current The type of this entry.
dynamicUnicast(1) - unicast address that learned from source
address of ingress frames.
staticUnicast(2) - unicast address that configured by management
and will remain so after the next reset of the device. Upto
10 static unicast entries can be configured for each port.
managementUnicast(3) - unicast address that configured for
management purpose or the MAC address of the device itself.
Management unicast entries are read-only.
dynamicMulticast(4) - dynamic multicast address that configured
by IGMP snooping. These entries are read-only.
staticMulticast(5) - multicast address that configured by
management and will remain so after the next reset of the
device.
-- Upto 10 static multicast entries can be configured.
managementMulticast(6) - multicast address that configured for
management purpose, such as GVRP and so on. These entries
are read-only.
Management entries are read-only. Dynamic entries can be read
and delete. Only static entries are read-create.
| ||||
| CmacAddressPortList | 1.3.6.1.4.1.2882.2.1.1.11.1.1.1.3 | PortList | RW | |
column · PortList · read-write · current The port list, which must be valid when creating a new entry. | ||||
| CmacAddressVlanId | 1.3.6.1.4.1.2882.2.1.1.11.1.1.1.4 | Integer32 | RW | |
column · Integer32 · read-write · current The VLAN where the mac address learned from or configured to. | ||||
| CmacAddressStatus | 1.3.6.1.4.1.2882.2.1.1.11.1.1.1.5 | RowStatus | RC | |
column · RowStatus · read-create · current This object is used to manage to creation and deletion of a static entry, and is used to indicate the status of an entry. To Creating a static entry, select a unused value of macAddressIndex and set macAddressStatus to 'createAndWait'. A row will then be created with status set to 'notReady' and its macAddressType, macAddressPortList and macAddressVlanId left unspecified. macAddressType, macAddressPortList and macAddressVlanId are mandatory to activate an entry to the device. macAddressStatus remains 'notReady' if any of these three objects are invalid. macAddressStatus will be changed to 'notInService' when the three objects are correctly configured. Set macAddressStatus to 'active' to activate the MAC entry to the device. Static unicast and multicast entries and dynamic unicast entries are removable. To delete a MAC entry, select the macAddressIndex set macAddressStatus to 'destory'. The row and the corresponding MAC address configurarion will be removed from the device. Set macAddressStatus to 'createAndGo', 'notInService', 'notReady' have no effects. | ||||
| SmacAddrTableClear | 1.3.6.1.4.1.2882.2.1.1.11.1.2 | INTEGER | RW | |
scalar · INTEGER · read-write · current Set to clear for cleaning all the dynamic MAC entries in the MAC address table.
| ||||
| SmacAddrTableAgingTime | 1.3.6.1.4.1.2882.2.1.1.11.1.3 | INTEGER (0..3825) | RW | |
scalar · INTEGER (0..3825) · read-write · current This value determines the interval that an automatic learned MAC address entry remains valid in the forwarding database, since its last access as a source address, before being purged. The value should be times of 15 in seconds. The minimum age time is 15 seconds. The maximum age time is 3825 seconds or almost 64 minutes. if the value is set to 0, the aging function is disabled and all learned address will remain in the database forever. | ||||
| NportStatistic | 1.3.6.1.4.1.2882.2.1.1.11.2 | |||
| TswitchPortStatTable | 1.3.6.1.4.1.2882.2.1.1.11.2.1 | NA | ||
table · not-accessible · current Table of descriptive and statistics information about each switch ports. | ||||
| RswitchPortStatEntry | 1.3.6.1.4.1.2882.2.1.1.11.2.1.1 | NA | ||
row · not-accessible · current An entry in the table containing descriptive information and statistics of a port.
| ||||
| CswPortStatIndex | 1.3.6.1.4.1.2882.2.1.1.11.2.1.1.1 | Integer32 | NA | |
column · Integer32 · not-accessible · current Index of port statistic table. | ||||
| CswPortStatType | 1.3.6.1.4.1.2882.2.1.1.11.2.1.1.2 | INTEGER | RO | |
column · INTEGER · read-only · current Indicates the port type.
| ||||
| CswPortStatLink | 1.3.6.1.4.1.2882.2.1.1.11.2.1.1.3 | INTEGER | RO | |
column · INTEGER · read-only · current Indicates the link state.
| ||||
| CswPortStatState | 1.3.6.1.4.1.2882.2.1.1.11.2.1.1.4 | INTEGER | RO | |
column · INTEGER · read-only · current Indicates the port state.
| ||||
| CswPortStatRXGoodPkt | 1.3.6.1.4.1.2882.2.1.1.11.2.1.1.5 | Integer32 | RO | |
column · Integer32 · read-only · current The count of good frames received, which is the total number of recieved unicast, broadcast, multicast and pause frames. | ||||
| CswPortStatRXBadPkt | 1.3.6.1.4.1.2882.2.1.1.11.2.1.1.6 | Integer32 | RO | |
column · Integer32 · read-only · current The count of bad frames received, which is the total number of undersize, fragment, oversize, jabber, RXErr and FCSErr frames. | ||||
| CswPortStatRXAbortPkt | 1.3.6.1.4.1.2882.2.1.1.11.2.1.1.7 | Integer32 | RO | |
column · Integer32 · read-only · current The count of abort frames when receive, which is the total number of discarded and filtered frames. | ||||
| CswPortStatTXGoodPkt | 1.3.6.1.4.1.2882.2.1.1.11.2.1.1.8 | Integer32 | RO | |
column · Integer32 · read-only · current The count of good frames transmitted, which is the total number of transmitted unicast, broadcast, multicast and pause frames. | ||||
| CswPortStatTXBadPkt | 1.3.6.1.4.1.2882.2.1.1.11.2.1.1.9 | Integer32 | RO | |
column · Integer32 · read-only · current The count of FCSErr frames when transmit. | ||||
| CswPortStatPacketCollision | 1.3.6.1.4.1.2882.2.1.1.11.2.1.1.10 | Integer32 | RO | |
column · Integer32 · read-only · current The count of collision. | ||||
| SswitchPortStatClear | 1.3.6.1.4.1.2882.2.1.1.11.2.2 | INTEGER | WO | |
scalar · INTEGER · write-only · current Set to clear(1) to clear all information in the statistics table.
| ||||
| Nportmirroring | 1.3.6.1.4.1.2882.2.1.1.11.3 | |||
| SportMirrorStatus | 1.3.6.1.4.1.2882.2.1.1.11.3.1 | INTEGER | RW | |
scalar · INTEGER · read-write · current To enable or disable port mirroring. Port mirroring is used to send a copy of inbound or outbound network packets seen on one port to another switch port. Administrators may utilized this mechanism to monitor network traffic as well as the performance of a switch.
| ||||
| SportMirrorDestinationPortTX | 1.3.6.1.4.1.2882.2.1.1.11.3.2 | Integer32 (0..10) | RW | |
scalar · Integer32 (0..10) · read-write · current The TX destination port (sniffer port). Destination port can be used to see all monitor port traffic. You can connect sniffer port to a LAN analysier or netxray. Set to 0 to clear the configuration. A destination port can not be the same as a source port. This object can not be modified if portMirrorStatus is disable. | ||||
| SportMirrorDestinationPortRX | 1.3.6.1.4.1.2882.2.1.1.11.3.3 | Integer32 (0..10) | RW | |
scalar · Integer32 (0..10) · read-write · current The RX destination port (sniffer port). Destination port can be used to see all monitor port traffic. You can connect sniffer port to a LAN analysier or netxray. Set to 0 to clear the configuration. A destination port can not be the same as a source port. This object can not be modified if portMirrorStatus is disable. | ||||
| TportMirrorSourceTable | 1.3.6.1.4.1.2882.2.1.1.11.3.4 | NA | ||
table · not-accessible · current Table of descriptive information and configuration of port mirroring in this system. Use this table to select monitor port for this switch. | ||||
| RportMirrorSourceEntry | 1.3.6.1.4.1.2882.2.1.1.11.3.4.1 | NA | ||
row · not-accessible · current Information configuring port mirroring on each port.
| ||||
| CportMirrorPortNum | 1.3.6.1.4.1.2882.2.1.1.11.3.4.1.1 | Integer32 (1..10) | RO | |
column · Integer32 (1..10) · read-only · current The Port number. | ||||
| CportMirrorSourcePort | 1.3.6.1.4.1.2882.2.1.1.11.3.4.1.2 | INTEGER | RW | |
column · INTEGER · read-write · current The mode of source port (monitor port). (1) TX only. (2) RX only. (3) RX and TX. (4) Source port is disabled. The ports you want to monitor. All source port traffic will be copied to destination port (sniffer port). This object can not be modified if portMirrorStatus is disable.
| ||||
| NeventLog | 1.3.6.1.4.1.2882.2.1.1.11.4 | |||
| SeventLogClear | 1.3.6.1.4.1.2882.2.1.1.11.4.1 | INTEGER | RW | |
scalar · INTEGER · read-write · current clear all event log.
| ||||
| TeventLogTable | 1.3.6.1.4.1.2882.2.1.1.11.4.2 | NA | ||
table · not-accessible · current Table of descriptive information about logs. | ||||
| ReventLogEntry | 1.3.6.1.4.1.2882.2.1.1.11.4.2.1 | NA | ||
| CeventLogIndex | 1.3.6.1.4.1.2882.2.1.1.11.4.2.1.1 | Integer32 | RO | |
column · Integer32 · read-only · current Index of log. | ||||
| CeventLogDescription | 1.3.6.1.4.1.2882.2.1.1.11.4.2.1.2 | DisplayString (SIZE (0..100)) | RO | |
column · DisplayString (SIZE (0..100)) · read-only · current The description of a log. | ||||
| Nsave | 1.3.6.1.4.1.2882.2.1.1.12 | |||
| SsaveCfgMgtAction | 1.3.6.1.4.1.2882.2.1.1.12.1 | INTEGER | RW | |
scalar · INTEGER · read-write · current Setting this object to active(1) saves current configuration. Setting this object to notActive(2) has no effect. The system always returns the value notActive(2) when this object is read.
| ||||
Textual conventions
AlertTypeINTEGERdisable(2)enable(1)