CISCOSB-rlInterfaces
ciscoSystemsThe private MIB module definition for Switch Interfaces.
snmptranslate -m CISCOSB-rlInterfaces -Tpsnmpwalk -v2c -c <community> -m CISCOSB-rlInterfaces <host> 1.3.6.1.4.1.9.6.1.101.43Imports
| CISCOSB-MIB | rlIfInterfaces, switch001 |
|---|---|
| IF-MIB | InterfaceIndex, InterfaceIndexOrZero, ifIndex |
| Q-BRIDGE-MIB | PortList |
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP |
| SNMPv2-SMI | Bits, Counter32, Integer32, IpAddress, MODULE-IDENTITY, MibIdentifier, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, iso |
| SNMPv2-TC | DisplayString, PhysAddress, RowStatus, TEXTUAL-CONVENTION, TruthValue |
OID tree
| Name | OID | Type | Access | Status | Example | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| IswInterfaces | 1.3.6.1.4.1.9.6.1.101.43 | ||||||||||||
identity The private MIB module definition for Switch Interfaces. | |||||||||||||
| TswIfTable | 1.3.6.1.4.1.9.6.1.101.43.1 | NA | |||||||||||
table · not-accessible · current Switch media specific information and configuration of the device interfaces. | |||||||||||||
| RswIfEntry | 1.3.6.1.4.1.9.6.1.101.43.1.1 | NA | |||||||||||
row · not-accessible · current Defines the contents of each line in the swIfTable table.
| |||||||||||||
| CswIfIndex | 1.3.6.1.4.1.9.6.1.101.43.1.1.1 | INTEGER | RO | ||||||||||
column · INTEGER · read-only · current Index to the swIfTable. The interface defined by a particular value of this index is the same interface as identified by the same value of ifIndex (MIB II). | |||||||||||||
| CswIfPhysAddressType | 1.3.6.1.4.1.9.6.1.101.43.1.1.2 | INTEGER | RW | obsolete | |||||||||
column · INTEGER · read-write · obsolete This variable indicates whether the physical address assigned to this interface should be the default one or be chosen from the set of reserved physical addresses of the device.
| |||||||||||||
| CswIfDuplexAdminMode | 1.3.6.1.4.1.9.6.1.101.43.1.1.3 | INTEGER | RW | ||||||||||
column · INTEGER · read-write · current This variable specifies whether this interface should operate in half duplex or full duplex mode. This specification will take effect only if swIfSpeedDuplexAutoNegotiation is disabled. A value of 'none' is returned if a value of the variable hasn't been set.
| |||||||||||||
| CswIfDuplexOperMode | 1.3.6.1.4.1.9.6.1.101.43.1.1.4 | INTEGER | RO | ||||||||||
column · INTEGER · read-only · current This variable indicates whether this interface operates in half duplex or full duplex mode. This variable can have the values hybrid or unknown only for a trunk. unknown - only if trunk operative status is not present.
| |||||||||||||
| CswIfBackPressureMode | 1.3.6.1.4.1.9.6.1.101.43.1.1.5 | INTEGER | RW | ||||||||||
column · INTEGER · read-write · current This variable indicates whether this interface activates back pressure when congested.
| |||||||||||||
| CswIfTaggedMode | 1.3.6.1.4.1.9.6.1.101.43.1.1.6 | INTEGER | RW | ||||||||||
column · INTEGER · read-write · current If enable, this interface operates in tagged mode, i.e all frames sent out through this interface will have the 802.1Q header. If disabled the frames will not be tagged.
| |||||||||||||
| CswIfTransceiverType | 1.3.6.1.4.1.9.6.1.101.43.1.1.7 | INTEGER | RO | ||||||||||
column · INTEGER · read-only · current This variable indicates the transceiver type of this interface.
| |||||||||||||
| CswIfLockAdminStatus | 1.3.6.1.4.1.9.6.1.101.43.1.1.8 | INTEGER | RW | ||||||||||
column · INTEGER · read-write · current This variable indicates whether this interface should operate in locked or unlocked mode. In unlocked mode the device learns all MAC addresses from this port and forwards all frames arrived at this port. In locked mode no new MAC addresses are learned and only frames with known source MAC addresses are forwarded.
| |||||||||||||
| CswIfLockOperStatus | 1.3.6.1.4.1.9.6.1.101.43.1.1.9 | INTEGER | RO | ||||||||||
column · INTEGER · read-only · current This variable defines whether this interface operates in locked
or unlocked mode. It is locked in each of the following two cases:
1) if swLockAdminStatus is set to locked
2) no IP/IPX interface is defined over this interface and no
VLAN contains this interface.
In unlocked mode the device learns all MAC addresses from this port and
forwards all frames arrived at this port. In locked mode no new MAC
addresses are learned and only frames with known source MAC
addresses are forwarded.
| |||||||||||||
| CswIfType | 1.3.6.1.4.1.9.6.1.101.43.1.1.10 | INTEGER | RO | ||||||||||
column · INTEGER · read-only · current This variable specifies the type of interface.
| |||||||||||||
| CswIfDefaultTag | 1.3.6.1.4.1.9.6.1.101.43.1.1.11 | INTEGER (0..4095) | RO | ||||||||||
column · INTEGER (0..4095) · read-only · current This variable specifies the default VLAN tag which will be attached to outgoing frames if swIfTaggedMode for this interface is enabled. | |||||||||||||
| CswIfDefaultPriority | 1.3.6.1.4.1.9.6.1.101.43.1.1.12 | INTEGER (0..7) | RW | ||||||||||
column · INTEGER (0..7) · read-write · current This variable specifies the default port priority. | |||||||||||||
| CswIfStatus | 1.3.6.1.4.1.9.6.1.101.43.1.1.13 | RowStatus | RW | ||||||||||
column · RowStatus · read-write · current The status of a table entry. It is used to delete an entry from this table. | |||||||||||||
| CswIfFlowControlMode | 1.3.6.1.4.1.9.6.1.101.43.1.1.14 | INTEGER | RW | ||||||||||
column · INTEGER · read-write · current on - Flow control will be enabled on this interface according to the
IEEE 802.3x standard.
off - Flow control is disabled.
autoNegotiation - Flow control will be enabled or disabled on this
interface. If enabled, it will operate as specified
by the IEEE 802.3x standard.
enabledRx - Flow control will be enabled on this interface for
recieved frames.
enabledTx - Flow control will be enabled on this interface for
transmitted frames.
An attempt to set this object to 'enabledRx(4)' or 'enabledTx(5)'
will fail on interfaces that do not support operation
at greater than 100 Mb/s.
In any case, flow control can work only if swIfDuplexOperMode is
full.
| |||||||||||||
| CswIfSpeedAdminMode | 1.3.6.1.4.1.9.6.1.101.43.1.1.15 | INTEGER | RW | ||||||||||
column · INTEGER · read-write · current This variable specifies the required speed of this interface in bits per second. This specification will take effect only if swIfSpeedDuplexAutoNegotiation is disabled. A value of 10 is returned for 10G. A value of 0 is returned if the value of the variable hasn't been set. | |||||||||||||
| CswIfSpeedDuplexAutoNegotiation | 1.3.6.1.4.1.9.6.1.101.43.1.1.16 | INTEGER | RW | ||||||||||
column · INTEGER · read-write · current If enabled the speed and duplex mode will be set by the device through the autonegotiation process. Otherwise these characteristics will be set according to the values of swIfSpeedAdminMode and swIfSpeedDuplexAutoNegotiation.
| |||||||||||||
| CswIfOperFlowControlMode | 1.3.6.1.4.1.9.6.1.101.43.1.1.17 | INTEGER | RO | ||||||||||
column · INTEGER · read-only · current on - Flow control is enabled on this interface according to the
IEEE 802.3x standard.
off - Flow control is disabled.
enabledRx - Flow control is enabled on this interface for
recieved frames.
enabledTx - Flow control is enabled on this interface for
transmitted frames.
| |||||||||||||
| CswIfOperSpeedDuplexAutoNegotiation | 1.3.6.1.4.1.9.6.1.101.43.1.1.18 | INTEGER | RO | ||||||||||
column · INTEGER · read-only · current If enabled the speed and duplex are determined by the device through the autonegotiation process. If disabled these characteristics are determined according to the values of swIfSpeedAdminMode and swIfDuplexAdminMode. hybrid - only for a trunk. unknown - only for ports that there operative status is not present.
| |||||||||||||
| CswIfOperBackPressureMode | 1.3.6.1.4.1.9.6.1.101.43.1.1.19 | INTEGER | RO | ||||||||||
column · INTEGER · read-only · current This variable indicates the operative back pressure mode of this interface.
| |||||||||||||
| CswIfAdminLockAction | 1.3.6.1.4.1.9.6.1.101.43.1.1.20 | INTEGER | RW | ||||||||||
column · INTEGER · read-write · current This variable indicates which action this interface should be taken in locked mode and therefore relevant only in locked mode. Possible actions: discard(1) - every packet is dropped. forwardNormal(2) - every packet is forwarded according to the DST address. discardDisable(3) - drops the first packet and suspends the port.
| |||||||||||||
| CswIfOperLockAction | 1.3.6.1.4.1.9.6.1.101.43.1.1.21 | INTEGER | RO | ||||||||||
column · INTEGER · read-only · current This variable indicates which action this interface actually takes in locked mode and therefore relevant only in locked mode. Possible actions: discard(1) - every packet is dropped. forwardNormal(2) - every packet is forwarded according to the DST address. discardDisable(3) - drops the first packet and suspends the port.
| |||||||||||||
| CswIfAdminLockTrapEnable | 1.3.6.1.4.1.9.6.1.101.43.1.1.22 | TruthValue | RW | ||||||||||
column · TruthValue · read-write · current This variable indicates whether to create a SNMP trap in the locked mode. | |||||||||||||
| CswIfOperLockTrapEnable | 1.3.6.1.4.1.9.6.1.101.43.1.1.23 | TruthValue | RO | ||||||||||
column · TruthValue · read-only · current This variable indicates whether a SNMP trap can be created in the locked mode. | |||||||||||||
| CswIfOperSuspendedStatus | 1.3.6.1.4.1.9.6.1.101.43.1.1.24 | TruthValue | RO | 2 | |||||||||
column · TruthValue · read-only · current This variable indicates whether the port is suspended or not due to some feature. After reboot this value is false Example values from LibreNMS test devices
| |||||||||||||
| CswIfLockOperTrapCount | 1.3.6.1.4.1.9.6.1.101.43.1.1.25 | INTEGER (0..2147483647) | RO | ||||||||||
column · INTEGER (0..2147483647) · read-only · current This variable indicates the trap counter status per ifIndex (i.e. number of received packets since the last trap sent due to a packet which was received on this ifIndex). It's relevant only in locked mode while trap is enabled. | |||||||||||||
| CswIfLockAdminTrapFrequency | 1.3.6.1.4.1.9.6.1.101.43.1.1.26 | INTEGER (1..1000000) | RW | ||||||||||
column · INTEGER (1..1000000) · read-write · current This variable indicates the minimal frequency (in seconds) of sending a trap per ifIndex. It's relevant only in locked mode and in trap enabled. | |||||||||||||
| CswIfReActivate | 1.3.6.1.4.1.9.6.1.101.43.1.1.27 | TruthValue | RW | ||||||||||
column · TruthValue · read-write · current This variable reactivates (enables) an ifIndex (which was suspended) | |||||||||||||
| CswIfAdminMdix | 1.3.6.1.4.1.9.6.1.101.43.1.1.28 | INTEGER | RW | ||||||||||
column · INTEGER · read-write · current The configuration is on a physical port, not include trunks. cross - The interface should force crossover. normal - The interface should not force crossover. auto - Auto mdix is enabled on the interface.
| |||||||||||||
| CswIfOperMdix | 1.3.6.1.4.1.9.6.1.101.43.1.1.29 | INTEGER | RO | ||||||||||
column · INTEGER · read-only · current cross - The interface is in crossover mode.
normal - The interface is not in crossover mode.
unknown - Only for port that its operative status is not present
or down.
| |||||||||||||
| CswIfHostMode | 1.3.6.1.4.1.9.6.1.101.43.1.1.30 | INTEGER | RW | ||||||||||
column · INTEGER · read-write · current This variable indicates the 802.1X host mode of a port. Relevant when the port's 802.1X control is auto. In addtion multiple-auth was added.
| |||||||||||||
| CswIfSingleHostViolationAdminAction | 1.3.6.1.4.1.9.6.1.101.43.1.1.31 | INTEGER | RW | ||||||||||
column · INTEGER · read-write · current This variable indicates which action this interface should take in single authorized. Possible actions: discard - every packet is dropped. forwardNormal - every packet is forwarded according to the DST address. discardDisable - drops the first packet and suspends the port.
| |||||||||||||
| CswIfSingleHostViolationOperAction | 1.3.6.1.4.1.9.6.1.101.43.1.1.32 | INTEGER | RO | ||||||||||
column · INTEGER · read-only · current This variable indicates which action this interface actually takes in single authorized. Possible actions: discard(1) - every packet is dropped. forwardNormal(2) - every packet is forwarded according to the DST address. discardDisable(3) - drops the first packet and suspends the port.
| |||||||||||||
| CswIfSingleHostViolationAdminTrapEnable | 1.3.6.1.4.1.9.6.1.101.43.1.1.33 | TruthValue | RW | ||||||||||
column · TruthValue · read-write · current This variable indicates whether to create a SNMP trap in single authorized. | |||||||||||||
| CswIfSingleHostViolationOperTrapEnable | 1.3.6.1.4.1.9.6.1.101.43.1.1.34 | TruthValue | RO | ||||||||||
column · TruthValue · read-only · current This variable indicates whether a SNMP trap can be created in the single authorized. | |||||||||||||
| CswIfSingleHostViolationOperTrapCount | 1.3.6.1.4.1.9.6.1.101.43.1.1.35 | INTEGER (0..2147483647) | RO | ||||||||||
column · INTEGER (0..2147483647) · read-only · current This variable indicates the trap counter status per ifIndex (i.e. number of received packets since the last trap sent due to a packet which was received on this ifIndex). It's relevant only in single authorized while trap is enabled. | |||||||||||||
| CswIfSingleHostViolationAdminTrapFrequency | 1.3.6.1.4.1.9.6.1.101.43.1.1.36 | INTEGER (0..1000000) | RW | ||||||||||
column · INTEGER (0..1000000) · read-write · current This variable indicates the minimal frequency (in seconds) of sending a trap per ifIndex. It's relevant only in single authorized and in trap enabled. A value of 0 means that trap is disabled. | |||||||||||||
| CswIfLockLimitationMode | 1.3.6.1.4.1.9.6.1.101.43.1.1.37 | INTEGER | RW | ||||||||||
column · INTEGER · read-write · current This variable indicates what is the learning limitation on the locked interface.
Possible values:
disabled - learning is stopped. The dynamic addresses associated with the
port are not aged out or relearned on other port as long as the port is
locked.
dynamic - dynamic addresses can be learned up to the maximum dynamic addresses
allowed on the port. Relearning and aging of the dynamic addresses are
enabled. The learned addresses aren't kept after reset.
secure-permanent - secure addresses can be learned up to the maximum addresses
allowed on the port. Relearning and aging of addresses are disabled.
The learned addresses are kept after reset.
secure-delete-on-reset - secure addresses can be learned up to the maximum addresses
allowed on the port. Relearning and aging of addresses are disabled.
The learned addresses are not kept after reset.
| |||||||||||||
| CswIfLockMaxMacAddresses | 1.3.6.1.4.1.9.6.1.101.43.1.1.38 | INTEGER (0..2147483647) | RW | ||||||||||
column · INTEGER (0..2147483647) · read-write · current This variable defines the maximum number of dynamic addresses that can be asscoiated with the locked interface. It isn't relevant in disabled limitation mode. | |||||||||||||
| CswIfLockMacAddressesCount | 1.3.6.1.4.1.9.6.1.101.43.1.1.39 | INTEGER (0..2147483647) | RO | ||||||||||
column · INTEGER (0..2147483647) · read-only · current This variable indicates the actual number of dynamic addresses that can be asscoiated with the locked interface. It isn't relevant in disabled limitation mode. | |||||||||||||
| CswIfAdminSpeedDuplexAutoNegotiationLocalCapabilities | 1.3.6.1.4.1.9.6.1.101.43.1.1.40 | AutoNegCapabilitiesBits | RW | ||||||||||
column · AutoNegCapabilitiesBits · read-write · current Administrative auto negotiation capabilities of the interface that can be advertised when swIfSpeedDuplexAutoNegotiation is enabled. default bit means advertise all the port's capabilities according to its type. | |||||||||||||
| CswIfOperSpeedDuplexAutoNegotiationLocalCapabilities | 1.3.6.1.4.1.9.6.1.101.43.1.1.41 | AutoNegCapabilitiesBits | RO | ||||||||||
column · AutoNegCapabilitiesBits · read-only · current Operative auto negotiation capabilities of the remote link. unknown bit means that port operative status is not up. | |||||||||||||
| CswIfSpeedDuplexNegotiationRemoteCapabilities | 1.3.6.1.4.1.9.6.1.101.43.1.1.42 | AutoNegCapabilitiesBits | RO | ||||||||||
column · AutoNegCapabilitiesBits · read-only · current Operative auto negotiation capabilities of the remote link. unknown bit means that port operative status is not up, or auto negotiation process not complete, or remote link is not auto negotiation able. | |||||||||||||
| CswIfAdminComboMode | 1.3.6.1.4.1.9.6.1.101.43.1.1.43 | INTEGER | RW | ||||||||||
column · INTEGER · read-write · current This variable specifies the administrative mode of a combo Ethernet interface.
| |||||||||||||
| CswIfOperComboMode | 1.3.6.1.4.1.9.6.1.101.43.1.1.44 | INTEGER | RO | ||||||||||
column · INTEGER · read-only · current This variable specifies the operative mode of a combo Ethernet interface.
| |||||||||||||
| CswIfAutoNegotiationMasterSlavePreference | 1.3.6.1.4.1.9.6.1.101.43.1.1.45 | INTEGER | RW | ||||||||||
column · INTEGER · read-write · current This variable specifies the administrative mode of the Maste-Slave preference in auto negotiation.
| |||||||||||||
| CswIfPortCapabilities | 1.3.6.1.4.1.9.6.1.101.43.1.1.46 | AutoNegCapabilitiesBits | RO | ||||||||||
column · AutoNegCapabilitiesBits · read-only · current Returns the port capabilities. | |||||||||||||
| SswIfMibVersion | 1.3.6.1.4.1.9.6.1.101.43.2 | INTEGER | RO | ||||||||||
scalar · INTEGER · read-only · current The swIfTable Mib's version, the current version is 3. | |||||||||||||
| SswIfPortLockSupport | 1.3.6.1.4.1.9.6.1.101.43.3 | INTEGER | RO | ||||||||||
scalar · INTEGER · read-only · current indicates if the locked port package is supported.
| |||||||||||||
| SswIfPortLockActionSupport | 1.3.6.1.4.1.9.6.1.101.43.4 | OCTET STRING (SIZE (1)) | RO | ||||||||||
scalar · OCTET STRING (SIZE (1)) · read-only · current indicates which port lock actions are supported:
(bit 0 is the most significant bit)
bit 0 - discard
bit 1 - forwardNormal
bit 2 - discardDisable | |||||||||||||
| SswIfPortLockTrapSupport | 1.3.6.1.4.1.9.6.1.101.43.5 | OCTET STRING (SIZE (1)) | RO | ||||||||||
scalar · OCTET STRING (SIZE (1)) · read-only · current indicates with which port lock actions the trap option is supported
(e.g. discard indicates that trap is supported only when the portlock
action is discard):
(bit 0 is the most significant bit)
bit 0 - discard
bit 1 - forwardNormal
bit 2 - discardDisable | |||||||||||||
| TswIfPortLockIfRangeTable | 1.3.6.1.4.1.9.6.1.101.43.6 | NA | |||||||||||
table · not-accessible · current Port lock interfaces range configuration | |||||||||||||
| RswIfPortLockIfRangeEntry | 1.3.6.1.4.1.9.6.1.101.43.6.1 | NA | |||||||||||
row · not-accessible · current Defines the contents of each line in the swIfPortLockIfRangeTable table. | |||||||||||||
| CswIfPortLockIfRangeIndex | 1.3.6.1.4.1.9.6.1.101.43.6.1.1 | INTEGER | RO | ||||||||||
column · INTEGER · read-only · current Index to the swIfPortLockIfRangeTable. | |||||||||||||
| CswIfPortLockIfRange | 1.3.6.1.4.1.9.6.1.101.43.6.1.2 | PortList | RW | ||||||||||
column · PortList · read-write · current The set of interfaces to which the port lock parameters should be configured | |||||||||||||
| CswIfPortLockIfRangeLockStatus | 1.3.6.1.4.1.9.6.1.101.43.6.1.3 | INTEGER | RW | ||||||||||
column · INTEGER · read-write · current This variable indicates whether the interfaces range should operate in locked or unlocked mode. In unlocked mode the device learns all MAC addresses from these interfaces and forwards all frames arrived at these interfaces. In locked mode no new MAC addresses are learned and only frames with known source MAC addresses are forwarded.
| |||||||||||||
| CswIfPortLockIfRangeAction | 1.3.6.1.4.1.9.6.1.101.43.6.1.4 | INTEGER | RW | ||||||||||
column · INTEGER · read-write · current This variable indicates which action for these interfaces should be take in locked mode and therefore relevant only in locked mode. Possible actions: discard(1) - every packet is dropped. forwardNormal(2) - every packet is forwarded according to the DST address. discardDisable(3) - drops the first packet and suspends the port.
| |||||||||||||
| CswIfPortLockIfRangeTrapEn | 1.3.6.1.4.1.9.6.1.101.43.6.1.5 | TruthValue | RW | ||||||||||
column · TruthValue · read-write · current This variable indicates whether to create a SNMP trap in the locked mode. | |||||||||||||
| CswIfPortLockIfRangeTrapFreq | 1.3.6.1.4.1.9.6.1.101.43.6.1.6 | INTEGER (1..1000000) | RW | ||||||||||
column · INTEGER (1..1000000) · read-write · current This variable indicates the minimal frequency (in seconds) of sending a trap for these interfaces. It's relevant only in locked mode and in trap enabled. | |||||||||||||
| TswIfExtTable | 1.3.6.1.4.1.9.6.1.101.43.7 | NA | |||||||||||
table · not-accessible · current Display information and configuration of the device interfaces. | |||||||||||||
| RswIfExtEntry | 1.3.6.1.4.1.9.6.1.101.43.7.1 | NA | |||||||||||
| CswIfExtSFPSpeed | 1.3.6.1.4.1.9.6.1.101.43.7.1.1 | INTEGER | RW | ||||||||||
column · INTEGER · read-write · current Configure speed of an SFP Ethernet interface.
| |||||||||||||
| TrlMacOperationTable | 1.3.6.1.4.1.9.6.1.101.43.8 | NA | |||||||||||
table · not-accessible · current pefrom mac operation on given ifindex | |||||||||||||
| RmacOperationEntry | 1.3.6.1.4.1.9.6.1.101.43.8.1 | NA | |||||||||||
| CmacOpifIndex | 1.3.6.1.4.1.9.6.1.101.43.8.1.1 | INTEGER | RO | ||||||||||
column · INTEGER · read-only · current Index to the rlMacOperationTable. The interface defined by a particular value of this index is the same interface as identified by the same value of ifIndex (MIB II). | |||||||||||||
| CmacOpType | 1.3.6.1.4.1.9.6.1.101.43.8.1.2 | INTEGER | RW | ||||||||||
column · INTEGER · read-write · current This variable indicates what operation should be performed on the MAC of the given interface.
| |||||||||||||
| SrlIfMibVersion | 1.3.6.1.4.1.9.6.1.101.54.1 | INTEGER | RO | ||||||||||
scalar · INTEGER · read-only · current MIB's version, the current version is 1. | |||||||||||||
| SrlIfNumOfPhPorts | 1.3.6.1.4.1.9.6.1.101.54.2 | INTEGER | RO | ||||||||||
scalar · INTEGER · read-only · current Total number of physical ports on this device (including all stack units) | |||||||||||||
| SrlIfMapOfOnPhPorts | 1.3.6.1.4.1.9.6.1.101.54.3 | OCTET STRING | RO | ||||||||||
scalar · OCTET STRING · read-only · current Each bit in this octet string indicates that the correspondig port's ifOperStatus is ON if set. The mapping of port number to bits in this octet string is as follows: The port with the L2 interface number 1 is mapped to the least significant bit of the 1st octet, the port with L2 ifNumber 2 to the next significant bit in the 1st octet, port 8 to the most-significant bit of the in the 1st octet, port 9 to the least significant bit of the 2nd octet, etc. and in general, port n to bit corresponding to 2**((n mod 8) -1) in byte n/8 + 1 | |||||||||||||
| SrlIfClearPortMibCounters | 1.3.6.1.4.1.9.6.1.101.54.4 | PortList | RW | ||||||||||
scalar · PortList · read-write · current Each bit that is set in this portList represent a port that its mib counters should be reset. | |||||||||||||
| SrlIfNumOfUserDefinedPorts | 1.3.6.1.4.1.9.6.1.101.54.5 | INTEGER | RO | ||||||||||
scalar · INTEGER · read-only · current The number of user defined ports on this device. | |||||||||||||
| SrlIfFirstOutOfBandIfIndex | 1.3.6.1.4.1.9.6.1.101.54.6 | INTEGER | RO | ||||||||||
scalar · INTEGER · read-only · current First ifIndex of out-of-band port. This scalar exists only the device has out of band ports. | |||||||||||||
| SrlIfNumOfLoopbackPorts | 1.3.6.1.4.1.9.6.1.101.54.7 | INTEGER | RO | ||||||||||
scalar · INTEGER · read-only · current The number of loopback ports on this device. | |||||||||||||
| SrlIfFirstLoopbackIfIndex | 1.3.6.1.4.1.9.6.1.101.54.8 | INTEGER | RO | ||||||||||
scalar · INTEGER · read-only · current First ifIndex of loopback port. This scalar will exists only if rlIfNumOfLoopbackPorts is different from 0. | |||||||||||||
| SrlIfExistingPortList | 1.3.6.1.4.1.9.6.1.101.54.9 | PortList | RO | ||||||||||
scalar · PortList · read-only · current Indicates which ports/trunks exist in the system. It doesn't indicate which are present. | |||||||||||||
| SrlIfBaseMACAddressPerIfIndex | 1.3.6.1.4.1.9.6.1.101.54.10 | TruthValue | RW | ||||||||||
scalar · TruthValue · read-write · current Indicates if the system will assign a unique MAC per Ethernet port or not. | |||||||||||||
| SrlFlowControlCascadeMode | 1.3.6.1.4.1.9.6.1.101.54.11 | INTEGER | RW | ||||||||||
scalar · INTEGER · read-write · current enable disable flow control on cascade ports
| |||||||||||||
| SrlFlowControlCascadeType | 1.3.6.1.4.1.9.6.1.101.54.12 | INTEGER | RW | ||||||||||
scalar · INTEGER · read-write · current define which type of ports will be affected by flow control on cascade ports
| |||||||||||||
| SrlFlowControlRxPerSystem | 1.3.6.1.4.1.9.6.1.101.54.13 | TruthValue | RW | ||||||||||
scalar · TruthValue · read-write · current define if flow control RX is supported per system. | |||||||||||||
| SrlCascadePortProtectionAction | 1.3.6.1.4.1.9.6.1.101.54.14 | TruthValue | RW | ||||||||||
scalar · TruthValue · read-write · current As a result of this set all of the local cascade ports will stop being consider unstable and will be force up. | |||||||||||||
| SrlManagementIfIndex | 1.3.6.1.4.1.9.6.1.101.54.15 | InterfaceIndex | RW | ||||||||||
scalar · InterfaceIndex · read-write · current Specify L2 bound management interface index in a single IP address system when configurable management interface is supported. | |||||||||||||
| SrlIfClearStackPortsCounters | 1.3.6.1.4.1.9.6.1.101.54.16 | TruthValue | RW | ||||||||||
scalar · TruthValue · read-write · current As a result of this set all counters of all external cascade ports will be cleared. | |||||||||||||
| SrlIfClearPortMacAddresses | 1.3.6.1.4.1.9.6.1.101.54.17 | InterfaceIndexOrZero | RW | ||||||||||
scalar · InterfaceIndexOrZero · read-write · current if port is non secure, its all dynamic MAC addresses are cleared. if port is secure, its all secure MAC addresses which have learned or configured are cleared. | |||||||||||||
| SrlIfCutThroughPacketLength | 1.3.6.1.4.1.9.6.1.101.54.18 | INTEGER (257..16383) | RW | ||||||||||
scalar · INTEGER (257..16383) · read-write · current The default packet length that is assigned to a packet in the Cut-Through mode. | |||||||||||||
| SrlIfCutPriorityZero | 1.3.6.1.4.1.9.6.1.101.54.19 | TruthValue | RW | ||||||||||
scalar · TruthValue · read-write · current Enable or disable cut-Through for priority 0. | |||||||||||||
| SrlIfCutPriorityOne | 1.3.6.1.4.1.9.6.1.101.54.20 | TruthValue | RW | ||||||||||
scalar · TruthValue · read-write · current Enable or disable cut-Through for priority 1. | |||||||||||||
| SrlIfCutPriorityTwo | 1.3.6.1.4.1.9.6.1.101.54.21 | TruthValue | RW | ||||||||||
scalar · TruthValue · read-write · current Enable or disable cut-Through for priority 2. | |||||||||||||
| SrlIfCutPriorityThree | 1.3.6.1.4.1.9.6.1.101.54.22 | TruthValue | RW | ||||||||||
scalar · TruthValue · read-write · current Enable or disable cut-Through for priority 3. | |||||||||||||
| SrlIfCutPriorityFour | 1.3.6.1.4.1.9.6.1.101.54.23 | TruthValue | RW | ||||||||||
scalar · TruthValue · read-write · current Enable or disable cut-Through for priority 4. | |||||||||||||
| SrlIfCutPriorityFive | 1.3.6.1.4.1.9.6.1.101.54.24 | TruthValue | RW | ||||||||||
scalar · TruthValue · read-write · current Enable or disable cut-Through for priority 5. | |||||||||||||
| SrlIfCutPrioritySix | 1.3.6.1.4.1.9.6.1.101.54.25 | TruthValue | RW | ||||||||||
scalar · TruthValue · read-write · current Enable or disable cut-Through for priority 6. | |||||||||||||
| SrlIfCutPrioritySeven | 1.3.6.1.4.1.9.6.1.101.54.26 | TruthValue | RW | ||||||||||
scalar · TruthValue · read-write · current Enable or disable cut-Through for priority 7. | |||||||||||||
| TrlIfCutThroughTable | 1.3.6.1.4.1.9.6.1.101.54.27 | NA | |||||||||||
table · not-accessible · current Information and configuration of cut-through feature. | |||||||||||||
| RrlIfCutThroughEntry | 1.3.6.1.4.1.9.6.1.101.54.27.1 | NA | |||||||||||
row · not-accessible · current Defines the contents of each line in the swIfTable table.
| |||||||||||||
| CrlIfCutThroughPriorityEnable | 1.3.6.1.4.1.9.6.1.101.54.27.1.1 | TruthValue | RW | ||||||||||
column · TruthValue · read-write · current Enable or disable cut-through for a priority for an interface. | |||||||||||||
| CrlIfCutThroughUntaggedEnable | 1.3.6.1.4.1.9.6.1.101.54.27.1.2 | TruthValue | RW | ||||||||||
column · TruthValue · read-write · current Enable or disable cut-through for untagged packets for an interface. | |||||||||||||
| CrlIfCutThroughOperMode | 1.3.6.1.4.1.9.6.1.101.54.27.1.3 | TruthValue | RO | ||||||||||
column · TruthValue · read-only · current Operational mode of spesific cut-through interface. | |||||||||||||
| SrlCutThroughPacketLength | 1.3.6.1.4.1.9.6.1.101.54.28 | INTEGER | RO | ||||||||||
scalar · INTEGER · read-only · current The default packet length that is assigned to a packet in the Cut-Through mode. | |||||||||||||
| SrlCutThroughPacketLengthAfterReset | 1.3.6.1.4.1.9.6.1.101.54.29 | INTEGER (257..16383) | RW | ||||||||||
scalar · INTEGER (257..16383) · read-write · current The default packet length that is assigned to a packet in the Cut-Through mode after reset. | |||||||||||||
| SrlCutThroughEnable | 1.3.6.1.4.1.9.6.1.101.54.30 | TruthValue | RO | ||||||||||
scalar · TruthValue · read-only · current Cut-Through global enable mode. | |||||||||||||
| SrlCutThroughEnableAfterReset | 1.3.6.1.4.1.9.6.1.101.54.31 | TruthValue | RW | ||||||||||
scalar · TruthValue · read-write · current Cut-Through global enable mode after reset. | |||||||||||||
| SrlFlowControlMode | 1.3.6.1.4.1.9.6.1.101.54.32 | INTEGER | RW | ||||||||||
scalar · INTEGER · read-write · current Define which mode will be enabled on flow control enabled ports. The interfaces with enabled flow control will receive pause frames, but will not send flow control pause frames Send-receive: The interfaces with enabled flow control will receive and send pause frames. Receive-only: The interfaces with enabled flow control will receive pause frames, but will not send flow control pause frames.
| |||||||||||||
| SrlIfPortsNegotationTuning | 1.3.6.1.4.1.9.6.1.101.54.33 | TruthValue | RW | ||||||||||
scalar · TruthValue · read-write · current indicates if to apply link negotiation tuning WA globally for all ports with PHY 3140. | |||||||||||||
| SrlFlowControlPerSystem | 1.3.6.1.4.1.9.6.1.101.54.34 | TruthValue | RW | ||||||||||
scalar · TruthValue · read-write · current define if flow control is enabled on all regular ports and trunk in the system or not. | |||||||||||||
Textual conventions
AutoNegCapabilitiesBitsBitsdefault(0)fastFull(5)fastHalf(4)fiftyGigaFull(13)fiveGigaFull(9)fortyGigaFull(12)gigaFull(7)gigaHalf(6)oneHundredGigaFull(14)tenFull(3)tenGigaFull(8)tenHalf(2)twentyFiveGigaFull(11)twoPointFiveGigaFull(10)unknown(1)Auto negotiation capabilities bits.