CISCOSB-IpRouter
ciscoSystemsThe private MIB module definition for switch001 router MIB.
snmptranslate -m CISCOSB-IpRouter -Tpsnmpwalk -v2c -c <community> -m CISCOSB-IpRouter <host> 1.3.6.1.4.1.9.6.1.101.26.18Imports
| CISCOSB-IP | ipRedundancy, ipRipFilter, ipRouteLeaking, ipSpec, rip2Spec, rlIpRoutingProtPreference, rlOspf |
|---|---|
| OSPF-MIB | AreaID, RouterID, ospfIfEntry, ospfVirtIfEntry |
| RIPv2-MIB | rip2IfConfEntry |
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP |
| SNMPv2-SMI | Bits, Counter32, Integer32, IpAddress, MODULE-IDENTITY, MibIdentifier, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, iso |
| SNMPv2-TC | DisplayString, PhysAddress, RowStatus, TEXTUAL-CONVENTION, TruthValue |
OID tree
| Name | OID | Type | Access | Status |
|---|---|---|---|---|
| TrsRip2IfConfTable | 1.3.6.1.4.1.9.6.1.101.26.3.1 | NA | ||
table · not-accessible · current This table is extension of rip2IfConfTable (RFC 1724 ,RIP 2) | ||||
| RrsRip2IfConfEntry | 1.3.6.1.4.1.9.6.1.101.26.3.1.1 | NA | ||
| CrsRip2IfConfAddress | 1.3.6.1.4.1.9.6.1.101.26.3.1.1.1 | IpAddress | RO | |
column · IpAddress · read-only · current The IP Address of this system on the indicated subnet. | ||||
| CrsRip2IfConfVirtualDis | 1.3.6.1.4.1.9.6.1.101.26.3.1.1.2 | INTEGER | RW | |
column · INTEGER · read-write · current This variable defines the virtual number of hops assigned to the interface specified by rsIfIpAddrIndex. This enables fine-tuning of the RIP routing algorithm. | ||||
| CrlRip2IfConfKeyChain | 1.3.6.1.4.1.9.6.1.101.26.3.1.1.3 | DisplayString | RW | |
column · DisplayString · read-write · current Name of the key-chain which rip2 interface uses for md5 authentication | ||||
| CrlRip2IfConfAdminStatus | 1.3.6.1.4.1.9.6.1.101.26.3.1.1.4 | INTEGER | RW | |
column · INTEGER · read-write · current This variable defines administrative status of RIP interface.
| ||||
| CrlRip2IfConfInFilteringType | 1.3.6.1.4.1.9.6.1.101.26.3.1.1.5 | INTEGER | RW | |
column · INTEGER · read-write · current Type of Rx filtering (ACL, Prefix List etc).
| ||||
| CrlRip2IfConfOutFilteringType | 1.3.6.1.4.1.9.6.1.101.26.3.1.1.6 | INTEGER | RW | |
column · INTEGER · read-write · current Type of Tx filtering (ACL, Prefix List etc).
| ||||
| CrlRip2IfConfInFilterListName | 1.3.6.1.4.1.9.6.1.101.26.3.1.1.7 | DisplayString | RW | |
column · DisplayString · read-write · current Name of a filtering list. The list defines which networks are to be received and which are to be suppressed in routing updates. List type is defined by rlRip2IfConfFilteringType. | ||||
| CrlRip2IfConfOutFilterListName | 1.3.6.1.4.1.9.6.1.101.26.3.1.1.8 | DisplayString | RW | |
column · DisplayString · read-write · current Name of a filtering list. The list defines which networks are to be sent and which are to be suppressed. List type is defined by rlRip2IfConfFilteringType. | ||||
| CrlRip2IfConfDefInfOriginate | 1.3.6.1.4.1.9.6.1.101.26.3.1.1.9 | INTEGER | RW | |
column · INTEGER · read-write · current if set to global RIP behavior is specified by the value of rlRip2GlobalDefaultInformationOriginate scalar if set to enabled RIP will advertise default route on this interfaces if set to passiveOnly RIP will advertise default route on this interfaces only if it is configured to passive mode
| ||||
| SrlRip2MibVersion | 1.3.6.1.4.1.9.6.1.101.26.3.2 | INTEGER | RO | |
scalar · INTEGER · read-only · current MIB's version, the current version is 2. | ||||
| SrlRip2RedistDefaultMetric | 1.3.6.1.4.1.9.6.1.101.26.3.3 | Unsigned32 (1..15) | RW | |
scalar · Unsigned32 (1..15) · read-write · current Default metric value when RIP advertises routes, derived by other protocols. | ||||
| SrlRip2RedistStaticTransparent | 1.3.6.1.4.1.9.6.1.101.26.3.4 | TruthValue | RW | |
scalar · TruthValue · read-write · current If set to TRUE causes RIP to use the routing table metric for redistributed static routes as the RIP metric. If set to FALSE then the metric defined in rlRip2RedistDefaultMetric is used. | ||||
| SrlRip2ClearStatistics | 1.3.6.1.4.1.9.6.1.101.26.3.5 | TruthValue | RW | |
scalar · TruthValue · read-write · current Clears RIP statistics counters of all interfaces and all peers. | ||||
| SrlRip2IfConfGlobalPassiveInterface | 1.3.6.1.4.1.9.6.1.101.26.3.6 | TruthValue | RW | |
scalar · TruthValue · read-write · current if set to TRUE all interfaces created will be created as passive (rip2IfConfSend = doNotSend) | ||||
| SrlRip2GlobalDefInfOriginate | 1.3.6.1.4.1.9.6.1.101.26.3.7 | INTEGER | RW | |
scalar · INTEGER · read-write · current if set to Enabled RIP will advertise default route on all RIP interfaces if set to PassiveOnly RIP will advertise default route on all RIP passive interfaces
| ||||
| SrlRip2RedistConnected | 1.3.6.1.4.1.9.6.1.101.26.3.8 | TruthValue | RW | |
scalar · TruthValue · read-write · current If set to TRUE causes RIP to redistribute directly connected interfaces, on which RIP is not enabled. | ||||
| SrlRip2RedistConnectedTransparent | 1.3.6.1.4.1.9.6.1.101.26.3.9 | TruthValue | RW | |
scalar · TruthValue · read-write · current If set to TRUE causes RIP to use the routing table metric for redistributed connected routes as the RIP metric. If set to FALSE then the metric defined in rlRip2RedistDefaultMetric is used. | ||||
| SrlRip2RedistConnectedMetric | 1.3.6.1.4.1.9.6.1.101.26.3.10 | Unsigned32 (0..15) | RW | |
scalar · Unsigned32 (0..15) · read-write · current User defined metric value when RIP advertises directly connected interfaces, on which RIP is not enabled. | ||||
| SipRedundAdminStatus | 1.3.6.1.4.1.9.6.1.101.26.6.1 | INTEGER | RW | |
scalar · INTEGER · read-write · current This parameter controls the IP Redundancy in the device. In case the parameter is Enable and the other router becomes inoperational, all the traffic is handled by this element.
| ||||
| SipRedundOperStatus | 1.3.6.1.4.1.9.6.1.101.26.6.2 | INTEGER | RO | |
scalar · INTEGER · read-only · current obsolete
| ||||
| TipRedundRoutersTable | 1.3.6.1.4.1.9.6.1.101.26.6.3 | NA | ||
table · not-accessible · current List of IP addresses backed up by this router. | ||||
| RipRedundRoutersEntry | 1.3.6.1.4.1.9.6.1.101.26.6.3.1 | NA | ||
row · not-accessible · current The row definition for this table. | ||||
| CipRedundRoutersIfAddr | 1.3.6.1.4.1.9.6.1.101.26.6.3.1.1 | IpAddress | RO | |
column · IpAddress · read-only · current The Ip address of the IP interface on which the redundancy feature is operational. | ||||
| CipRedundRoutersMainRouterAddr | 1.3.6.1.4.1.9.6.1.101.26.6.3.1.2 | IpAddress | RO | |
column · IpAddress · read-only · current The Ip address of the polled main router. | ||||
| CipRedundRoutersOperStatus | 1.3.6.1.4.1.9.6.1.101.26.6.3.1.3 | INTEGER | RO | |
column · INTEGER · read-only · current If active, the main router is considered inoperational and the IP interface operates as its backup.
| ||||
| CipRedundRoutersPollInterval | 1.3.6.1.4.1.9.6.1.101.26.6.3.1.4 | INTEGER | RW | |
column · INTEGER · read-write · current Polling interval for this router (in seconds). If 0 the router is not polled. | ||||
| CipRedundRoutersTimeout | 1.3.6.1.4.1.9.6.1.101.26.6.3.1.5 | INTEGER | RW | |
column · INTEGER · read-write · current Interval in seconds during which the backed-up router must signal. If it does not signal, it is considered inoperational and the IP interface starts operating as backup. | ||||
| CipRedundRoutersStatus | 1.3.6.1.4.1.9.6.1.101.26.6.3.1.6 | INTEGER | RW | |
column · INTEGER · read-write · current Entry status
| ||||
| SipLeakStaticToRip | 1.3.6.1.4.1.9.6.1.101.26.7.1 | INTEGER | RW | |
scalar · INTEGER · read-write · current This parameter controls leaking (redistribution) of static routes to RIP. When enabled, all routes inserted to the IP routing table via SNMP are advertised into RIP.
| ||||
| SipLeakStaticToOspf | 1.3.6.1.4.1.9.6.1.101.26.7.2 | INTEGER | RW | |
scalar · INTEGER · read-write · current This parameter controls leaking (redistribution) of static routes into OSPF. When enabled, all routes inserted to the IP routing table via SNMP are advertised into OSPF as external routes.
| ||||
| SipLeakOspfToRip | 1.3.6.1.4.1.9.6.1.101.26.7.3 | INTEGER | RW | |
scalar · INTEGER · read-write · current This parameter controls leaking (redistribution) of routes from OSPF to RIP. If enabled, all routes learned via OSPF are advertised into RIP.
| ||||
| SipLeakRipToOspf | 1.3.6.1.4.1.9.6.1.101.26.7.4 | INTEGER | RW | |
scalar · INTEGER · read-write · current This parameter controls leaking (redistribution) of routes from RIP to OSPF. If enabled, all routes learned via RIP are advertised into OSPF as external routes.
| ||||
| SipLeakExtDirectToOspf | 1.3.6.1.4.1.9.6.1.101.26.7.5 | INTEGER | RW | |
scalar · INTEGER · read-write · current This parameter controls leaking (redistribution) into OSPF of direct routes external to OSPF, i.e. routes to local network corresponding to IP interfaces on which OSPF is disabled. When enabled, all such direct routes are advertised into OSPF as external routes.
| ||||
| TrsIpRipFilterGlbTable | 1.3.6.1.4.1.9.6.1.101.26.8.1 | NA | ||
table · not-accessible · current The table of RIP global filters per IP router. | ||||
| RrsIpRipFilterGlbEntry | 1.3.6.1.4.1.9.6.1.101.26.8.1.1 | NA | ||
row · not-accessible · current An entry in the RIP global filter table | ||||
| CrsIpRipFilterGlbType | 1.3.6.1.4.1.9.6.1.101.26.8.1.1.1 | INTEGER | RO | |
column · INTEGER · read-only · current Type of filter - input/output
| ||||
| CrsIpRipFilterGlbNumber | 1.3.6.1.4.1.9.6.1.101.26.8.1.1.2 | INTEGER | RO | |
column · INTEGER · read-only · current Number of RIP filter. | ||||
| CrsIpRipFilterGlbStatus | 1.3.6.1.4.1.9.6.1.101.26.8.1.1.3 | INTEGER | RW | |
column · INTEGER · read-write · current The validity of this entry. Setting this value to invalid deletes the entry, and the entry may be actualy removed from the table.
| ||||
| CrsIpRipFilterGlbIpAddr | 1.3.6.1.4.1.9.6.1.101.26.8.1.1.4 | IpAddress | RW | |
column · IpAddress · read-write · current network prefix IP address, as in the forwarding table. | ||||
| CrsIpRipFilterGlbNetworkMaskBits | 1.3.6.1.4.1.9.6.1.101.26.8.1.1.5 | INTEGER | RW | |
column · INTEGER · read-write · current the number of bits in the IP Network mask, called network-prefix-length in Router Requirements terminology. for example: the value 16 means mask 255.255.0.0 | ||||
| CrsIpRipFilterGlbMatchBits | 1.3.6.1.4.1.9.6.1.101.26.8.1.1.6 | INTEGER | RW | |
column · INTEGER · read-write · current the number of bits to match in the Network IP address. A value smaller than 32 defines a wildcard. for example: the value 8 means all routes whose leftmost 8 bits are equal to those of the network IP address. If this variable has a value other than 32, than rsIpRipFilterGlbNetworkMaskBits must be 0 and is ignored. | ||||
| CrsIpRipFilterGlbAction | 1.3.6.1.4.1.9.6.1.101.26.8.1.1.7 | INTEGER | RW | |
column · INTEGER · read-write · current Filter action - permit/deny for this network
| ||||
| TrsIpRipFilterLclTable | 1.3.6.1.4.1.9.6.1.101.26.8.2 | NA | ||
table · not-accessible · current Table of input/output RIP filters used per IP Interface. | ||||
| RrsIpRipFilterLclEntry | 1.3.6.1.4.1.9.6.1.101.26.8.2.1 | NA | ||
row · not-accessible · current An entry in the Intf RIP filter table | ||||
| CrsIpRipFilterLclIpIntf | 1.3.6.1.4.1.9.6.1.101.26.8.2.1.1 | IpAddress | RO | |
column · IpAddress · read-only · current The IP address identifying the RIP interface for this filter. This value corresponds to rsIpAdEntAddr. | ||||
| CrsIpRipFilterLclType | 1.3.6.1.4.1.9.6.1.101.26.8.2.1.2 | INTEGER | RO | |
column · INTEGER · read-only · current Type of filter - input/output
| ||||
| CrsIpRipFilterLclNumber | 1.3.6.1.4.1.9.6.1.101.26.8.2.1.3 | INTEGER | RO | |
column · INTEGER · read-only · current Number of RIP filter for this Interface | ||||
| CrsIpRipFilterLclStatus | 1.3.6.1.4.1.9.6.1.101.26.8.2.1.4 | INTEGER | RW | |
column · INTEGER · read-write · current The validity of this entry. Setting this value to invalid deletes the entry, and the entry may be actualy removed from the table.
| ||||
| CrsIpRipFilterLclIpAddr | 1.3.6.1.4.1.9.6.1.101.26.8.2.1.5 | IpAddress | RW | |
column · IpAddress · read-write · current network prefix IP address, as in the forwarding table. | ||||
| CrsIpRipFilterLclNetworkMaskBits | 1.3.6.1.4.1.9.6.1.101.26.8.2.1.6 | INTEGER | RW | |
column · INTEGER · read-write · current the number of bits in the IP Network mask, called network-prefix-length in Router Requirements terminology. for example: the value 16 means mask 255.255.0.0 | ||||
| CrsIpRipFilterLclMatchBits | 1.3.6.1.4.1.9.6.1.101.26.8.2.1.7 | INTEGER | RW | |
column · INTEGER · read-write · current the number of bits to match in the Network IP address. A value smaller than 32 defines a wildcard. for example: the value 8 means all routes whose leftmost 8 bits are equal to those of the network IP address. If this variable has a value other than 32, than rsIpRipFilterLclNetworkMaskBits must be 0 and is ignored. | ||||
| CrsIpRipFilterLclAction | 1.3.6.1.4.1.9.6.1.101.26.8.2.1.8 | INTEGER | RW | |
column · INTEGER · read-write · current Filter action - permit/deny
| ||||
| SrlIpRoutingProtPreferenceDirect | 1.3.6.1.4.1.9.6.1.101.26.13.1 | INTEGER (0..254) | RW | |
scalar · INTEGER (0..254) · read-write · current The Preference given to routes whose origin is Local IP (i.e. IP interface in IpAddrTable) It is proposed that the value will be higher than dynamic routing protocols. The change of its value may lead to unexpected results, such as routing loops | ||||
| SrlIpRoutingProtPreferenceStatic | 1.3.6.1.4.1.9.6.1.101.26.13.2 | INTEGER (0..255) | RW | |
scalar · INTEGER (0..255) · read-write · current The Preference given to routes whose origin is Men configured by Net managment tools, i.e. Command line or SNMP configured. | ||||
| SrlIpRoutingProtPreferenceOspfInter | 1.3.6.1.4.1.9.6.1.101.26.13.3 | INTEGER (0..255) | RW | |
scalar · INTEGER (0..255) · read-write · current The Preference given to routes whose origin is internal ospf Links. Relate to routes which are based on OSPF Link State Advertisements of type 1-4 | ||||
| SrlIpRoutingProtPreferenceOspfExt | 1.3.6.1.4.1.9.6.1.101.26.13.4 | INTEGER (0..255) | RW | |
scalar · INTEGER (0..255) · read-write · current The Preference given to routes whose origin is external to OSPF i.e. routes imported by as OSPF AS Border router. Relate to routes which are based on OSPF Link State Advertisements of types 5 and 7 | ||||
| SrlIpRoutingProtPreferenceOspfReject | 1.3.6.1.4.1.9.6.1.101.26.13.5 | INTEGER (0..255) | RW | |
scalar · INTEGER (0..255) · read-write · current The Preference given to routes whose origin is OSPF and Are inserted to cover gaps in net range | ||||
| SrlIpRoutingProtPreferenceRipNormal | 1.3.6.1.4.1.9.6.1.101.26.13.6 | INTEGER (0..255) | RW | |
scalar · INTEGER (0..255) · read-write · current The Preference given to routes whose origin is RIP routing domain | ||||
| SrlIpRoutingProtPreferenceRipAggregate | 1.3.6.1.4.1.9.6.1.101.26.13.7 | INTEGER (0..255) | RW | |
scalar · INTEGER (0..255) · read-write · current The Preference given to routes whose origin is aggregation As a method of rip1 to handle the CIDR schema. The idea is that ripv1 aggregates route which fall into certion class of IP. This route is a discard route in effect, and is referenced, at forwarding route look up, if there is no beter match. (which means the route is not available) | ||||
| SrlIpRoutingProtPreferenceBgp | 1.3.6.1.4.1.9.6.1.101.26.13.8 | INTEGER (0..255) | RW | |
scalar · INTEGER (0..255) · read-write · current The Preference given to routes whose origin is BGP ROUTERS (EBGP or IBGP) | ||||
| SrlOspfMibVersion | 1.3.6.1.4.1.9.6.1.101.26.14.1 | INTEGER | RO | |
scalar · INTEGER · read-only · current MIB's version, the current version is 1. | ||||
| SrlOspfAutoInterfaceCreation | 1.3.6.1.4.1.9.6.1.101.26.14.2 | INTEGER | RO | |
scalar · INTEGER · read-only · current This variable controls OSPF automatic creation and activation of interfaces. If value is enable - IP interface creation results in creation and activation of OSPF Interface. If value is disable OSPF interface is created but not activated. The option is a platform parameter.
| ||||
| TrlOspfIfExtTable | 1.3.6.1.4.1.9.6.1.101.26.14.3 | NA | ||
table · not-accessible · current The OSPF Interface Table describes the interfaces from the viewpoint of OSPF. | ||||
| RrlOspfIfExtEntry | 1.3.6.1.4.1.9.6.1.101.26.14.3.1 | NA | ||
row · not-accessible · current The OSPF interface table extension for md5 authentication
| ||||
| CrlOspfifKeyChain | 1.3.6.1.4.1.9.6.1.101.26.14.3.1.1 | DisplayString | RW | |
column · DisplayString · read-write · current Name of the key-chain which ospf interface uses for md5 authentication | ||||
| TrlOspfRtrLnkTable | 1.3.6.1.4.1.9.6.1.101.26.14.4 | NA | ||
table · not-accessible · current Router Link State Advertisement. | ||||
| RrlOspfRtrLnkEntry | 1.3.6.1.4.1.9.6.1.101.26.14.4.1 | NA | ||
row · not-accessible · current A single entry from Router LSA. | ||||
| CrlOspfRtrLnkAreaId | 1.3.6.1.4.1.9.6.1.101.26.14.4.1.1 | AreaID | RO | |
column · AreaID · read-only · current The 32 bit identifier of the Area from which the LSA was received. | ||||
| CrlOspfRtrLnkLsid | 1.3.6.1.4.1.9.6.1.101.26.14.4.1.2 | IpAddress | RO | |
column · IpAddress · read-only · current The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being described by the advertisement. | ||||
| CrlOspfRtrLnkRouterId | 1.3.6.1.4.1.9.6.1.101.26.14.4.1.3 | RouterID | RO | |
column · RouterID · read-only · current The 32 bit number that uniquely identifies the originating router in the Autonomous System. | ||||
| CrlOspfRtrLnkIdx | 1.3.6.1.4.1.9.6.1.101.26.14.4.1.4 | Unsigned32 (1..65535) | RO | |
column · Unsigned32 (1..65535) · read-only · current The index is a unsigned 32-bit integer. It is used as sequence number of entry in the LSA and relevant only for Router or Network LSA which can contain unlimited number of entries. | ||||
| CrlOspfRtrLnkSequence | 1.3.6.1.4.1.9.6.1.101.26.14.4.1.5 | Integer32 | RO | |
column · Integer32 · read-only · current The sequence number field is a signed 32-bit integer. It is used to detect old and duplicate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement. | ||||
| CrlOspfRtrLnkAge | 1.3.6.1.4.1.9.6.1.101.26.14.4.1.6 | Integer32 | RO | |
column · Integer32 · read-only · current This field is the age of the link state advertisement in seconds. | ||||
| CrlOspfRtrLnkChecksum | 1.3.6.1.4.1.9.6.1.101.26.14.4.1.7 | Integer32 | RO | |
column · Integer32 · read-only · current This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connectionless datagrams; it is commonly referred to as the Fletcher checksum. | ||||
| CrlOspfRtrLnkLength | 1.3.6.1.4.1.9.6.1.101.26.14.4.1.8 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current The lenth in bytes of the LSA. This includes the 20 byte LSA header. | ||||
| CrlOspfRtrLnkBitV | 1.3.6.1.4.1.9.6.1.101.26.14.4.1.9 | INTEGER | RO | |
column · INTEGER · read-only · current When set, the router is an endpoint of one or more fully adjacent virtual links having the described area as Transit area (V is for virtual link endpoint).
| ||||
| CrlOspfRtrLnkBitE | 1.3.6.1.4.1.9.6.1.101.26.14.4.1.10 | INTEGER | RO | |
column · INTEGER · read-only · current When set, the router is an AS boundary router (E is for external).
| ||||
| CrlOspfRtrLnkBitB | 1.3.6.1.4.1.9.6.1.101.26.14.4.1.11 | INTEGER | RO | |
column · INTEGER · read-only · current When set, the router is an area border router (B is for border).
| ||||
| CrlOspfRtrLnkLinks | 1.3.6.1.4.1.9.6.1.101.26.14.4.1.12 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current The number of router links described in this LSA. This must be the total collection of router links (i.e., interfaces) to the area. | ||||
| CrlOspfRtrLnkLinkID | 1.3.6.1.4.1.9.6.1.101.26.14.4.1.13 | IpAddress | RO | |
column · IpAddress · read-only · current Identifies the object that this router link connects to. Value depends on the link's Type. | ||||
| CrlOspfRtrLnkLinkData | 1.3.6.1.4.1.9.6.1.101.26.14.4.1.14 | IpAddress | RO | |
column · IpAddress · read-only · current Value depends on the link's Type field. | ||||
| CrlOspfRtrLnkType | 1.3.6.1.4.1.9.6.1.101.26.14.4.1.15 | INTEGER | RO | |
column · INTEGER · read-only · current A quick description of the router link.
| ||||
| CrlOspfRtrLnkMetric | 1.3.6.1.4.1.9.6.1.101.26.14.4.1.16 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current The cost of using this router link. | ||||
| TrlOspfNetLnkTable | 1.3.6.1.4.1.9.6.1.101.26.14.5 | NA | ||
table · not-accessible · current Network Link State Advertisement. | ||||
| RrlOspfNetLnkEntry | 1.3.6.1.4.1.9.6.1.101.26.14.5.1 | NA | ||
row · not-accessible · current A single entry from Network LSA. | ||||
| CrlOspfNetLnkAreaId | 1.3.6.1.4.1.9.6.1.101.26.14.5.1.1 | AreaID | RO | |
column · AreaID · read-only · current The 32 bit identifier of the Area from which the LSA was received. | ||||
| CrlOspfNetLnkLsid | 1.3.6.1.4.1.9.6.1.101.26.14.5.1.2 | IpAddress | RO | |
column · IpAddress · read-only · current The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being described by the advertisement. | ||||
| CrlOspfNetLnkRouterId | 1.3.6.1.4.1.9.6.1.101.26.14.5.1.3 | RouterID | RO | |
column · RouterID · read-only · current The 32 bit number that uniquely identifies the originating router in the Autonomous System. | ||||
| CrlOspfNetLnkIdx | 1.3.6.1.4.1.9.6.1.101.26.14.5.1.4 | Unsigned32 (1..65535) | RO | |
column · Unsigned32 (1..65535) · read-only · current The index is a unsigned 32-bit integer. It is used as sequence number of entry in the LSA and relevant only for Router or Network LSA which can contain unlimited number of entries. | ||||
| CrlOspfNetLnkSequence | 1.3.6.1.4.1.9.6.1.101.26.14.5.1.5 | Integer32 | RO | |
column · Integer32 · read-only · current The sequence number field is a signed 32-bit integer. It is used to detect old and duplicate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement. | ||||
| CrlOspfNetLnkAge | 1.3.6.1.4.1.9.6.1.101.26.14.5.1.6 | Integer32 | RO | |
column · Integer32 · read-only · current This field is the age of the link state advertisement in seconds. | ||||
| CrlOspfNetLnkChecksum | 1.3.6.1.4.1.9.6.1.101.26.14.5.1.7 | Integer32 | RO | |
column · Integer32 · read-only · current This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connectionless datagrams; it is commonly referred to as the Fletcher checksum. | ||||
| CrlOspfNetLnkLength | 1.3.6.1.4.1.9.6.1.101.26.14.5.1.8 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current The lenth in bytes of the LSA. This includes the 20 byte LSA header. | ||||
| CrlOspfNetLnkMask | 1.3.6.1.4.1.9.6.1.101.26.14.5.1.9 | IpAddress | RO | |
column · IpAddress · read-only · current The IP address mask for the network. | ||||
| CrlOspfNetLnkAttRouter | 1.3.6.1.4.1.9.6.1.101.26.14.5.1.10 | IpAddress | RO | |
column · IpAddress · read-only · current The Router IDs of each of the routers attached to the network. | ||||
| TrlOspfSumLnkTable | 1.3.6.1.4.1.9.6.1.101.26.14.6 | NA | ||
table · not-accessible · current Summary Link State Advertisement for network (Type 3). | ||||
| RrlOspfSumLnkEntry | 1.3.6.1.4.1.9.6.1.101.26.14.6.1 | NA | ||
row · not-accessible · current A single entry from Summary LSA. | ||||
| CrlOspfSumLnkAreaId | 1.3.6.1.4.1.9.6.1.101.26.14.6.1.1 | AreaID | RO | |
column · AreaID · read-only · current The 32 bit identifier of the Area from which the LSA was received. | ||||
| CrlOspfSumLnkLsid | 1.3.6.1.4.1.9.6.1.101.26.14.6.1.2 | IpAddress | RO | |
column · IpAddress · read-only · current The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being described by the advertisement. | ||||
| CrlOspfSumLnkRouterId | 1.3.6.1.4.1.9.6.1.101.26.14.6.1.3 | RouterID | RO | |
column · RouterID · read-only · current The 32 bit number that uniquely identifies the originating router in the Autonomous System. | ||||
| CrlOspfSumLnkSequence | 1.3.6.1.4.1.9.6.1.101.26.14.6.1.4 | Integer32 | RO | |
column · Integer32 · read-only · current The sequence number field is a signed 32-bit integer. It is used to detect old and duplicate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement. | ||||
| CrlOspfSumLnkAge | 1.3.6.1.4.1.9.6.1.101.26.14.6.1.5 | Integer32 | RO | |
column · Integer32 · read-only · current This field is the age of the link state advertisement in seconds. | ||||
| CrlOspfSumLnkChecksum | 1.3.6.1.4.1.9.6.1.101.26.14.6.1.6 | Integer32 | RO | |
column · Integer32 · read-only · current This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connectionless datagrams; it is commonly referred to as the Fletcher checksum. | ||||
| CrlOspfSumLnkLength | 1.3.6.1.4.1.9.6.1.101.26.14.6.1.7 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current The lenth in bytes of the LSA. This includes the 20 byte LSA header. | ||||
| CrlOspfSumLnkMask | 1.3.6.1.4.1.9.6.1.101.26.14.6.1.8 | IpAddress | RO | |
column · IpAddress · read-only · current Value depends on the link's Type field. | ||||
| CrlOspfSumLnkMetric | 1.3.6.1.4.1.9.6.1.101.26.14.6.1.9 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current The cost of using this router link. | ||||
| TrlOspfAsbLnkTable | 1.3.6.1.4.1.9.6.1.101.26.14.7 | NA | ||
table · not-accessible · current Summary Link State Advertisement for ASBR (Type 4). | ||||
| RrlOspfAsbLnkEntry | 1.3.6.1.4.1.9.6.1.101.26.14.7.1 | NA | ||
row · not-accessible · current A single entry from Summary LSA. | ||||
| CrlOspfAsbLnkAreaId | 1.3.6.1.4.1.9.6.1.101.26.14.7.1.1 | AreaID | RO | |
column · AreaID · read-only · current The 32 bit identifier of the Area from which the LSA was received. | ||||
| CrlOspfAsbLnkLsid | 1.3.6.1.4.1.9.6.1.101.26.14.7.1.2 | IpAddress | RO | |
column · IpAddress · read-only · current The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being described by the advertisement. | ||||
| CrlOspfAsbLnkRouterId | 1.3.6.1.4.1.9.6.1.101.26.14.7.1.3 | RouterID | RO | |
column · RouterID · read-only · current The 32 bit number that uniquely identifies the originating router in the Autonomous System. | ||||
| CrlOspfAsbLnkSequence | 1.3.6.1.4.1.9.6.1.101.26.14.7.1.4 | Integer32 | RO | |
column · Integer32 · read-only · current The sequence number field is a signed 32-bit integer. It is used to detect old and duplicate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement. | ||||
| CrlOspfAsbLnkAge | 1.3.6.1.4.1.9.6.1.101.26.14.7.1.5 | Integer32 | RO | |
column · Integer32 · read-only · current This field is the age of the link state advertisement in seconds. | ||||
| CrlOspfAsbLnkChecksum | 1.3.6.1.4.1.9.6.1.101.26.14.7.1.6 | Integer32 | RO | |
column · Integer32 · read-only · current This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connectionless datagrams; it is commonly referred to as the Fletcher checksum. | ||||
| CrlOspfAsbLnkLength | 1.3.6.1.4.1.9.6.1.101.26.14.7.1.7 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current The lenth in bytes of the LSA. This includes the 20 byte LSA header. | ||||
| CrlOspfAsbLnkMetric | 1.3.6.1.4.1.9.6.1.101.26.14.7.1.8 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current The cost of using this router link. | ||||
| TrlOspfAseLnkTable | 1.3.6.1.4.1.9.6.1.101.26.14.8 | NA | ||
table · not-accessible · current External Link State Advertisement. | ||||
| RrlOspfAseLnkEntry | 1.3.6.1.4.1.9.6.1.101.26.14.8.1 | NA | ||
row · not-accessible · current A single entry from External LSA. | ||||
| CrlOspfAseLnkLsid | 1.3.6.1.4.1.9.6.1.101.26.14.8.1.1 | IpAddress | RO | |
column · IpAddress · read-only · current The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being described by the advertisement. | ||||
| CrlOspfAseLnkRouterId | 1.3.6.1.4.1.9.6.1.101.26.14.8.1.2 | RouterID | RO | |
column · RouterID · read-only · current The 32 bit number that uniquely identifies the originating router in the Autonomous System. | ||||
| CrlOspfAseLnkSequence | 1.3.6.1.4.1.9.6.1.101.26.14.8.1.3 | Integer32 | RO | |
column · Integer32 · read-only · current The sequence number field is a signed 32-bit integer. It is used to detect old and duplicate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement. | ||||
| CrlOspfAseLnkAge | 1.3.6.1.4.1.9.6.1.101.26.14.8.1.4 | Integer32 | RO | |
column · Integer32 · read-only · current This field is the age of the link state advertisement in seconds. | ||||
| CrlOspfAseLnkChecksum | 1.3.6.1.4.1.9.6.1.101.26.14.8.1.5 | Integer32 | RO | |
column · Integer32 · read-only · current This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connectionless datagrams; it is commonly referred to as the Fletcher checksum. | ||||
| CrlOspfAseLnkLength | 1.3.6.1.4.1.9.6.1.101.26.14.8.1.6 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current The lenth in bytes of the LSA. This includes the 20 byte LSA header. | ||||
| CrlOspfAseLnkMask | 1.3.6.1.4.1.9.6.1.101.26.14.8.1.7 | IpAddress | RO | |
column · IpAddress · read-only · current Value depends on the link's Type field. | ||||
| CrlOspfAseLnkFrwAddress | 1.3.6.1.4.1.9.6.1.101.26.14.8.1.8 | IpAddress | RO | |
column · IpAddress · read-only · current Data traffic for the advertised destination will be forwarded to this address. If the Forwarding address is set to 0.0.0.0, data traffic will be forwarded instead to the LSA's originator (i.e., the responsible AS boundary router). | ||||
| CrlOspfAseLnkBitE | 1.3.6.1.4.1.9.6.1.101.26.14.8.1.9 | INTEGER | RO | |
column · INTEGER · read-only · current The type of external metric. If bit E is set, the metric specified is a Type 2 external metric.
| ||||
| CrlOspfAseLnkMetric | 1.3.6.1.4.1.9.6.1.101.26.14.8.1.10 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current The cost of this route. | ||||
| CrlOspfAseLnkTag | 1.3.6.1.4.1.9.6.1.101.26.14.8.1.11 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current A 32-bit field attached to each external route. | ||||
| TrlospfVirtIfExtTable | 1.3.6.1.4.1.9.6.1.101.26.14.9 | NA | ||
table · not-accessible · current The Virtual Interface Table describes the virtual links that the OSPF Process is configured to carry on. | ||||
| RrlospfVirtIfExtEntry | 1.3.6.1.4.1.9.6.1.101.26.14.9.1 | NA | ||
row · not-accessible · current The OSPF virtual interface table extension for md5 authentication
| ||||
| CrlospfVirtifKeyChain | 1.3.6.1.4.1.9.6.1.101.26.14.9.1.1 | DisplayString | RW | |
column · DisplayString · read-write · current Name of the key-chain which ospf virtual interface uses for md5 authentication | ||||
| IrlIpRouter | 1.3.6.1.4.1.9.6.1.101.26.18 | |||
identity The private MIB module definition for switch001 router MIB. | ||||