CISCOSB-CDP-MIB
ciscoSystemsThe private MIB module definition for CDP protocol.
snmptranslate -m CISCOSB-CDP-MIB -Tpsnmpwalk -v2c -c <community> -m CISCOSB-CDP-MIB <host> 1.3.6.1.4.1.9.6.1.101.137Imports
| CISCO-CDP-MIB | cdpCacheDeviceIndex, cdpCacheEntry, cdpCacheIfIndex |
|---|---|
| CISCO-TC | CiscoNetworkAddress, CiscoNetworkProtocol |
| CISCOSB-DEVICEPARAMS-MIB | rndErrorDesc, rndErrorSeverity |
| CISCOSB-MIB | switch001 |
| CISCOSB-TRAPS-MIB | rndNotifications |
| IF-MIB | InterfaceIndex, InterfaceIndexOrZero |
| INET-ADDRESS-MIB | InetAddress, InetAddressType |
| Q-BRIDGE-MIB | PortList, VlanId |
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP |
| SNMPv2-SMI | Bits, Counter32, Integer32, IpAddress, MODULE-IDENTITY, MibIdentifier, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, iso |
| SNMPv2-TC | DisplayString, MacAddress, PhysAddress, TEXTUAL-CONVENTION, TruthValue |
OID tree
| Name | OID | Type | Access | Status |
|---|---|---|---|---|
| !rlCdpLogMismatchDuplexTrap | 1.3.6.1.4.1.9.6.1.101.0.224 | |||
notification · current Warning trap indicating that duplex mismatch has been detected by CDP
| ||||
| !rlCdpLogMismatchVoiceVlanTrap | 1.3.6.1.4.1.9.6.1.101.0.225 | |||
notification · current Warning trap indicating that voice vlan mismatch has been detected by CDP
| ||||
| !rlCdpLogMismatchNativeVlanTrap | 1.3.6.1.4.1.9.6.1.101.0.226 | |||
notification · current Warning trap indicating that native vlan mismatch has been detected by CDP
| ||||
| IrlCdp | 1.3.6.1.4.1.9.6.1.101.137 | |||
identity The private MIB module definition for CDP protocol. | ||||
| SrlCdpVersionAdvertised | 1.3.6.1.4.1.9.6.1.101.137.1 | RlCdpVersionTypes | RW | |
scalar · RlCdpVersionTypes · read-write · current Specifies the verison of sent CDP packets | ||||
| SrlCdpSourceInterface | 1.3.6.1.4.1.9.6.1.101.137.2 | InterfaceIndexOrZero | RW | |
scalar · InterfaceIndexOrZero · read-write · current Specifices the CDP source-interface, which the IP address advertised into TLV is accoding to this source-interface instead of the outgoing interface. value of 0 indicates no source interface. value must belong to an ethernet port/lag | ||||
| SrlCdpLogMismatchDuplexEnable | 1.3.6.1.4.1.9.6.1.101.137.3 | PortList | RW | |
scalar · PortList · read-write · current Enable logging messages when detecting mishmatch between advertised and received duplex mode. To enable loging on specific interface set the corresponing bit. | ||||
| TrlCdpCountersTable | 1.3.6.1.4.1.9.6.1.101.137.4 | NA | ||
table · not-accessible · current This table contains all cdp counter values, indexed by conter name | ||||
| RrlCdpCountersEntry | 1.3.6.1.4.1.9.6.1.101.137.4.1 | NA | ||
| CrlCdpCountersName | 1.3.6.1.4.1.9.6.1.101.137.4.1.1 | RlCdpCounterTypes | NA | |
column · RlCdpCounterTypes · not-accessible · current counter name used as key for counters table | ||||
| CrlCdpCountersValue | 1.3.6.1.4.1.9.6.1.101.137.4.1.2 | Counter32 | RO | |
column · Counter32 · read-only · current the value of the counter name specisifed by rlCdpCountersName, unsuppo will have no entry in the tab. | ||||
| SrlCdpCountersClear | 1.3.6.1.4.1.9.6.1.101.137.5 | TruthValue | RW | |
scalar · TruthValue · read-write · current By setting the MIB to True, all error and traffic counters are set to zero. | ||||
| SrlCdpCacheClear | 1.3.6.1.4.1.9.6.1.101.137.6 | TruthValue | RW | |
scalar · TruthValue · read-write · current By setting the MIB to True, all entries from the cdp cache table is deleted. | ||||
| SrlCdpVoiceVlanId | 1.3.6.1.4.1.9.6.1.101.137.7 | INTEGER (0..4094) | RW | obsolete |
scalar · INTEGER (0..4094) · read-write · obsolete voice vlan Id, used as the Appliance Vlan-Id TLV | ||||
| TrlCdpCacheTable | 1.3.6.1.4.1.9.6.1.101.137.8 | NA | ||
table · not-accessible · current The (conceptual) table contains externtion for the cdpCache table. indexed by cdpCacheEntry. | ||||
| RrlCdpCacheEntry | 1.3.6.1.4.1.9.6.1.101.137.8.1 | NA | ||
| CrlCdpCacheVersionExt | 1.3.6.1.4.1.9.6.1.101.137.8.1.1 | DisplayString | RO | |
column · DisplayString · read-only · current This field contains the extention of the cdpCacheVersion field in the cdpCache table. In case the neighbour advertised the SW TLV as a string with length larger than 160, this field contains the chacters from place 160 and on. Zero-length strings indicates no Version field (TLV) was reported in the most recent CDP message, or it was smaller than 160 chars | ||||
| CrlCdpCacheTimeToLive | 1.3.6.1.4.1.9.6.1.101.137.8.1.2 | INTEGER | RO | |
column · INTEGER · read-only · current This field indicates the time remains in seconds till the entry should be expried. | ||||
| CrlCdpCacheCdpVersion | 1.3.6.1.4.1.9.6.1.101.137.8.1.3 | RlCdpVersionTypes | RO | |
column · RlCdpVersionTypes · read-only · current This field indicates the cdp version that was reported in the most recent CDP message. | ||||
| SrlCdpPduAction | 1.3.6.1.4.1.9.6.1.101.137.9 | RlCdpPduActionTypes | RW | |
scalar · RlCdpPduActionTypes · read-write · current Defines CDP packets handling when CDP is globally disabled. | ||||
| SrlCdpLogMismatchVoiceVlanEnable | 1.3.6.1.4.1.9.6.1.101.137.10 | PortList | RW | |
scalar · PortList · read-write · current Enable logging messages when detecting mishmatch between advertised and received voice VLAN. To enable logging on specific interface set the corresponing bit. | ||||
| SrlCdpLogMismatchNativeVlanEnable | 1.3.6.1.4.1.9.6.1.101.137.11 | PortList | RW | |
scalar · PortList · read-write · current Enable logging messages when detecting mishmatch between advertised and received native VLAN. To enable loging on specific interface set the corresponing bit. | ||||
| TrlCdpSecondaryCacheTable | 1.3.6.1.4.1.9.6.1.101.137.12 | NA | ||
table · not-accessible · current The (conceptual) table contains partial information from cdpCache table. indexed by rlCdpSecondaryCacheEntry. | ||||
| RrlCdpSecondaryCacheEntry | 1.3.6.1.4.1.9.6.1.101.137.12.1 | NA | ||
row · not-accessible · current An entry (conceptual row) in the rlCdpSecondaryCacheTable, containing partial information received via CDP on one interface from one device. Entries appear when a CDP advertisement is received from a neighbor device. Entries disappear when CDP is disabled on the interface, globally or when the secondary cache is cleared | ||||
| CrlCdpSecondaryCacheMacAddress | 1.3.6.1.4.1.9.6.1.101.137.12.1.3 | MacAddress | RO | |
column · MacAddress · read-only · current The MAC address of the neighbor. | ||||
| CrlCdpSecondaryCachePlatform | 1.3.6.1.4.1.9.6.1.101.137.12.1.4 | DisplayString | RO | |
column · DisplayString · read-only · current The Device's Hardware Platform prefix, as reported in the most recent CDP message. The zero-length string indicates that no Platform field (TLV) was reported in the most recent CDP message. | ||||
| CrlCdpSecondaryCacheCapabilities | 1.3.6.1.4.1.9.6.1.101.137.12.1.5 | OCTET STRING (SIZE (0..4)) | RO | |
column · OCTET STRING (SIZE (0..4)) · read-only · current The Device's Functional Capabilities as reported in the most recent CDP message. | ||||
| CrlCdpSecondaryCacheVoiceVlanID | 1.3.6.1.4.1.9.6.1.101.137.12.1.6 | Unsigned32 (0..4095) | RO | |
column · Unsigned32 (0..4095) · read-only · current The remote device's VoIP VLAN ID, as reported in the most recent CDP message. This object is not instantiated if no Appliance VLAN-ID field (TLV) was reported in the most recently received CDP message. | ||||
| CrlCdpSecondaryCacheTimeToLive | 1.3.6.1.4.1.9.6.1.101.137.12.1.7 | INTEGER | RO | |
column · INTEGER · read-only · current This field indicates the number of seconds till the entry is expried. | ||||
| CrlCdpSecondaryCachePowerAvailable | 1.3.6.1.4.1.9.6.1.101.137.12.1.8 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current The remote device's available power, as reported in the
most recent CDP message.
A value of 0xFFFFFFFF indicates that no Power Available TLV
was reported in the most recently received CDP message. | ||||
| CrlCdpSecondaryCachePowerConsumption | 1.3.6.1.4.1.9.6.1.101.137.12.1.9 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current The remote device's consumed power, as reported in the
most recent CDP message.
A value of 0xFFFFFFFF indicates that no Power Consumption TLV
was reported in the most recently received CDP message. | ||||
| CrlCdpSecondaryCacheSparePairPoECapabilities | 1.3.6.1.4.1.9.6.1.101.137.12.1.10 | Bits | RO | |
column · Bits · read-only · current The remote device's Spare-Pair (4-wire) Power-Over-Ethernet negotiation capabilities.
The bit 'supported(0)' indicates that the device supports Spare Pair POE.
The bit 'detectionClassificationRequired(1)' indicates that the device requires
detection/classification on the spare-pair.
The bit 'desiredState(2)' indicates whether the PD device desires power
on the spare pair.
The bit 'operationalState(3)' indicates whether the PSE device supplies power
on the spare pair.
| ||||
| CrlCdpSecondaryCacheDeviceId | 1.3.6.1.4.1.9.6.1.101.137.12.1.11 | DisplayString | RO | |
column · DisplayString · read-only · current The remote device's Device-ID prefix, as reported in the most recent CDP message. The zero-length string indicates that no Device-ID TLV was reported in the most recent CDP message. | ||||
| CrlCdpSecondaryCachePortId | 1.3.6.1.4.1.9.6.1.101.137.12.1.12 | DisplayString | RO | |
column · DisplayString · read-only · current The remote device's Port-ID prefix, as reported in the most recent CDP message. The zero-length string indicates that no Port-ID TLV was reported in the most recent CDP message. | ||||
| CrlCdpSecondaryCachePowerAvailableManagementPowerLevel | 1.3.6.1.4.1.9.6.1.101.137.12.1.13 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current The remote device's Management Power Level, as reported in the
most recent CDP message Power Available TLV.
A value of zero indicates that no Power Available TLV
was reported in the most recently received CDP message. | ||||
| CrlCdpSecondaryCachePowerAvailableRequestId | 1.3.6.1.4.1.9.6.1.101.137.12.1.14 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current The remote device's echoed Request ID, as reported in the
most recent CDP message Power Available TLV.
A value of zero indicates that no Power Available TLV
was reported in the most recently received CDP message. | ||||
| CrlCdpSecondaryCachePowerAvailablePowerManagementId | 1.3.6.1.4.1.9.6.1.101.137.12.1.15 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current The remote device's Power Management ID, as reported in the
most recent CDP message Power Available TLV.
A value of zero indicates that no Power Available TLV
was reported in the most recently received CDP message. | ||||
| CrlCdpSecondaryCachePowerRequestedPowerManagementId | 1.3.6.1.4.1.9.6.1.101.137.12.1.16 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current The remote device's echoed Power Management ID, as reported in the
most recent CDP message Power Requested TLV.
A value of zero indicates that no Power Requested TLV
was reported in the most recently received CDP message. | ||||
| CrlCdpSecondaryCachePowerRequestedRequestId | 1.3.6.1.4.1.9.6.1.101.137.12.1.17 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current The remote device's Request ID, as reported in the
most recent CDP message Power Requested TLV.
A value of zero indicates that no Power Requested TLV
was reported in the most recently received CDP message. | ||||
| SrlCdpGlobalLogMismatchDuplexEnable | 1.3.6.1.4.1.9.6.1.101.137.13 | TruthValue | RW | |
scalar · TruthValue · read-write · current Globally enable/disable logging messages when detecting mishmatch between advertised and received duplex mode. | ||||
| SrlCdpGlobalLogMismatchVoiceVlanEnable | 1.3.6.1.4.1.9.6.1.101.137.14 | TruthValue | RW | |
scalar · TruthValue · read-write · current Globally enable/disable logging messages when detecting mishmatch between advertised and received voice VLAN. | ||||
| SrlCdpGlobalLogMismatchNativeVlanEnable | 1.3.6.1.4.1.9.6.1.101.137.15 | TruthValue | RW | |
scalar · TruthValue · read-write · current Globally enable/disable logging messages when detecting mishmatch between advertised and received native VLAN. | ||||
| TrlCdpTlvTable | 1.3.6.1.4.1.9.6.1.101.137.16 | NA | ||
table · not-accessible · current The (conceptual) table contains the local advertised information. indexed by rlCdpTlvEntry. | ||||
| RrlCdpTlvEntry | 1.3.6.1.4.1.9.6.1.101.137.16.1 | NA | ||
row · not-accessible · current An entry (conceptual row) in the rlCdpTlvTable, containing local information advertised by CDP on one interface. Entries are available only when CDP is globally enabled, for interfaces on which CDP is enabled and the interface state is UP.
| ||||
| CrlCdpTlvIfIndex | 1.3.6.1.4.1.9.6.1.101.137.16.1.1 | Unsigned32 (0..2147483647) | NA | |
column · Unsigned32 (0..2147483647) · not-accessible · current The ifIndex value of the local interface. A value of zero is used to access TLVs which do not changed between interfaces. | ||||
| CrlCdpTlvDeviceIdFormat | 1.3.6.1.4.1.9.6.1.101.137.16.1.2 | INTEGER | RO | |
column · INTEGER · read-only · current An indication of the format of Device-Id contained in the corresponding instance of rlCdpTlvDeviceId. serialNumber(1) indicates that the value of rlCdpTlvDeviceId object is in the form of an ASCII string contain the device serial number. macAddress(2) indicates that the value of rlCdpTlvDeviceId object is in the form of Layer 2 MAC address. other(3) indicates that the value of rlCdpTlvDeviceId object is in the form of a platform specific ASCII string contain info that identifies the device. For example: ASCII string contains serialNumber appended/prepened with system name.
| ||||
| CrlCdpTlvDeviceId | 1.3.6.1.4.1.9.6.1.101.137.16.1.3 | DisplayString | RO | |
column · DisplayString · read-only · current The Device-ID string as will be advertised in subsequent CDP messages. | ||||
| CrlCdpTlvAddress1Type | 1.3.6.1.4.1.9.6.1.101.137.16.1.4 | InetAddressType | RO | |
column · InetAddressType · read-only · current The Inet address type of rlCdpTlvAddress1 | ||||
| CrlCdpTlvAddress1 | 1.3.6.1.4.1.9.6.1.101.137.16.1.5 | InetAddress | RO | |
column · InetAddress · read-only · current The (first) network-layer address of the device as will be advertised in the Address TLV of subsequent CDP messages. For example, if the corresponding instance of rlCdpTlvAddress1Type had the value 'ipv4(1)', then this object would be an IPv4-address. | ||||
| CrlCdpTlvAddress2Type | 1.3.6.1.4.1.9.6.1.101.137.16.1.6 | InetAddressType | RO | |
column · InetAddressType · read-only · current The Inet address type of rlCdpTlvAddress2 | ||||
| CrlCdpTlvAddress2 | 1.3.6.1.4.1.9.6.1.101.137.16.1.7 | InetAddress | RO | |
column · InetAddress · read-only · current The (first) network-layer address of the device as will be advertised in the Address TLV of subsequent CDP messages. For example, if the corresponding instance of rlCdpTlvAddress2Type had the value 'ipv6(2)', then this object would be an IPv6-address. | ||||
| CrlCdpTlvAddress3Type | 1.3.6.1.4.1.9.6.1.101.137.16.1.8 | InetAddressType | RO | |
column · InetAddressType · read-only · current The Inet address type of rlCdpTlvAddress3 | ||||
| CrlCdpTlvAddress3 | 1.3.6.1.4.1.9.6.1.101.137.16.1.9 | InetAddress | RO | |
column · InetAddress · read-only · current The (first) network-layer address of the device as will be advertised in the Address TLV of subsequent CDP messages. For example, if the corresponding instance of rlCdpTlvAddress3Type had the value 'ipv6(2)', then this object would be an IPv6-address. | ||||
| CrlCdpTlvPortId | 1.3.6.1.4.1.9.6.1.101.137.16.1.10 | DisplayString | RO | |
column · DisplayString · read-only · current The Port-ID string as will be advertised in subsequent CDP messages from this interface. This will typically be the value of the ifName object (e.g., 'Ethernet0'). | ||||
| CrlCdpTlvCapabilities | 1.3.6.1.4.1.9.6.1.101.137.16.1.11 | OCTET STRING (SIZE (0..4)) | RO | |
column · OCTET STRING (SIZE (0..4)) · read-only · current The Device's Functional Capabilities as will be advertised in subsequent CDP messages. For latest set of specific values, see the latest version of the CDP specification. | ||||
| CrlCdpTlvVersion | 1.3.6.1.4.1.9.6.1.101.137.16.1.12 | DisplayString | RO | |
column · DisplayString · read-only · current The Version string as will be advertised in subsequent CDP messages. | ||||
| CrlCdpTlvPlatform | 1.3.6.1.4.1.9.6.1.101.137.16.1.13 | DisplayString | RO | |
column · DisplayString · read-only · current The Device's Hardware Platform as will be advertised in subsequent CDP messages. | ||||
| CrlCdpTlvNativeVLAN | 1.3.6.1.4.1.9.6.1.101.137.16.1.14 | Unsigned32 (0..4095) | RO | |
column · Unsigned32 (0..4095) · read-only · current The local device's interface's native VLAN, as will be advertised in subsequent CDP messages. | ||||
| CrlCdpTlvDuplex | 1.3.6.1.4.1.9.6.1.101.137.16.1.15 | INTEGER | RO | |
column · INTEGER · read-only · current The local device's interface's duplex mode, as will be advertised in subsequent CDP messages.
| ||||
| CrlCdpTlvApplianceID | 1.3.6.1.4.1.9.6.1.101.137.16.1.16 | Unsigned32 (0..255) | RO | |
column · Unsigned32 (0..255) · read-only · current The local device's Appliance ID, as will be advertised in subsequent CDP messages. A value of zero denotes no Appliance VLAN-ID TLV will be advertised in subsequent CDP messages. | ||||
| CrlCdpTlvApplianceVlanID | 1.3.6.1.4.1.9.6.1.101.137.16.1.17 | Unsigned32 (0..4095) | RO | |
column · Unsigned32 (0..4095) · read-only · current The local device's VoIP VLAN ID, as will be advertised in subsequent CDP messages. A value of zero denotes no Appliance VLAN-ID TLV will be advertised in subsequent CDP messages. | ||||
| CrlCdpTlvExtendedTrust | 1.3.6.1.4.1.9.6.1.101.137.16.1.18 | INTEGER | RO | |
column · INTEGER · read-only · current The local device's interface's extended trust mode, as will be advertised in subsequent CDP messages. A value of zero indicates the absence of extended trust.
| ||||
| CrlCdpTlvCosForUntrustedPorts | 1.3.6.1.4.1.9.6.1.101.137.16.1.19 | Unsigned32 (0..255) | RO | |
column · Unsigned32 (0..255) · read-only · current The COS value with which all packets received on an untrusted port should be marked by a simple switching device which cannot itself classify individual packets. This TLV only has any meaning if corresponding instance of rlCdpTlvExtendedTrust indicates the absence of extended trust. | ||||
| CrlCdpTlvPowerAvailableRequestId | 1.3.6.1.4.1.9.6.1.101.137.16.1.20 | Unsigned32 (0..65535) | RO | |
column · Unsigned32 (0..65535) · read-only · current The Power Available TLV Request-ID field echoes the Request-ID field last received in a Power Requested TLV. It is 0 if no Power Requested TLV has been received since the interface last transitioned to ifOperState == Up. | ||||
| CrlCdpTlvPowerAvailablePowerManagementId | 1.3.6.1.4.1.9.6.1.101.137.16.1.21 | Unsigned32 (1..65535) | RO | |
column · Unsigned32 (1..65535) · read-only · current The Power Available TLV Power-Management-ID field. | ||||
| CrlCdpTlvPowerAvailable | 1.3.6.1.4.1.9.6.1.101.137.16.1.22 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current The Power Available TLV Available-Power field indicates the
number of milliwatts of power available to powered devices at the
time this object is instatiated.
A value of 0xFFFFFFFF indicates that the Power Available TLV is not advertised. | ||||
| CrlCdpTlvPowerAvailableManagementPowerLevel | 1.3.6.1.4.1.9.6.1.101.137.16.1.23 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current The Power Available TLV Management-Power-Level field indicates the number of milliwatts representing the supplier's request to the powered device for its Power Consumption TLV. A value of 0xFFFFFFFF indicates the local device has no preference. | ||||
| CrlCdpTlvSysName | 1.3.6.1.4.1.9.6.1.101.137.16.1.24 | DisplayString | RO | |
column · DisplayString · read-only · current The sysName MIB as will be advertised in subsequent CDP messages. | ||||
| CrlCdpTlvPowerConsumption | 1.3.6.1.4.1.9.6.1.101.137.16.1.25 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current The value of Power Consumption TLV indicates the maximum amount of
power, in milliwatts, expected to be obtained and consumed from
the interface over which the CDP packet is sent.
A value of 0xFFFFFFFF indicates the TLV is not advertised. | ||||
| CrlCdpTlvPowerRequestedRequestId | 1.3.6.1.4.1.9.6.1.101.137.16.1.26 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current The Power Requested TLV Request-ID field. A value of zero indicates that the Power Requested TLV is not advertised. | ||||
| CrlCdpTlvPowerRequestedPowerManagementId | 1.3.6.1.4.1.9.6.1.101.137.16.1.27 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current The Power Requested TLV Power-Management-ID field echoes the Management-
Power-ID field in the last received Power Available TLV, or to 0,
if no Power Available TLV has been received. | ||||
| CrlCdpTlvSparePairPoECapabilities | 1.3.6.1.4.1.9.6.1.101.137.16.1.28 | Bits | RO | |
column · Bits · read-only · current The capabilities advertised in the Spare-Pair POE TLV. The bit 'supported(0)' indicates that the device supports Spare Pair POE. The bit 'detectionClassificationRequired(1)' indicates that the device requires detection/classification on the spare-pair. The bit 'desiredState(2)' indicates whether the PD device desires power on the spare pair. The bit 'operationalState(3)' indicates whether the PSE device supplies power on the spare pair.
| ||||
| SrlCdpAdvertiseApplianceTlv | 1.3.6.1.4.1.9.6.1.101.137.17 | TruthValue | RW | |
scalar · TruthValue · read-write · current By setting the MIB to True Appliance VLAN-ID TLV may be advertised. A value of False will prevent this TLV from being advertised. | ||||
| SrlCdpValidateMandatoryTlvs | 1.3.6.1.4.1.9.6.1.101.137.18 | TruthValue | RW | |
scalar · TruthValue · read-write · current By setting the MIB to true all mandatory TLVs 0x0001-0x0006 will be validated.
Incoming CDP frames without any of the TLVs will be dropped.
A value of false indicates that only the Device ID TLV (0x0001) is mandatory.
Frames containing Device ID TLV will be processed,
regardless of whether other TLVs are present or not. | ||||
| TrlCdpInterfaceCountersTable | 1.3.6.1.4.1.9.6.1.101.137.19 | NA | ||
table · not-accessible · current This table contains all CDP counter values, indexed by interface id. | ||||
| RrlCdpInterfaceCountersEntry | 1.3.6.1.4.1.9.6.1.101.137.19.1 | NA | ||
| CrlCdpInterfaceId | 1.3.6.1.4.1.9.6.1.101.137.19.1.1 | InterfaceIndex | NA | |
column · InterfaceIndex · not-accessible · current Interface id, used as index for interface counters table. | ||||
| CrlCdpInterfaceTotalInputPackets | 1.3.6.1.4.1.9.6.1.101.137.19.1.2 | Counter32 | RO | |
column · Counter32 · read-only · current Num of received packets on rlCdpInterfaceId | ||||
| CrlCdpInterfaceV1InputPackets | 1.3.6.1.4.1.9.6.1.101.137.19.1.3 | Counter32 | RO | |
column · Counter32 · read-only · current Num of v1 received packets on rlCdpInterfaceId | ||||
| CrlCdpInterfaceV2InputPackets | 1.3.6.1.4.1.9.6.1.101.137.19.1.4 | Counter32 | RO | |
column · Counter32 · read-only · current Num of v2 received packets on rlCdpInterfaceId | ||||
| CrlCdpInterfaceTotalOutputPackets | 1.3.6.1.4.1.9.6.1.101.137.19.1.5 | Counter32 | RO | |
column · Counter32 · read-only · current Num of sent packets from rlCdpInterfaceId | ||||
| CrlCdpInterfaceV1OutputPackets | 1.3.6.1.4.1.9.6.1.101.137.19.1.6 | Counter32 | RO | |
column · Counter32 · read-only · current Num of v1 sent packets from rlCdpInterfaceId | ||||
| CrlCdpInterfaceV2OutputPackets | 1.3.6.1.4.1.9.6.1.101.137.19.1.7 | Counter32 | RO | |
column · Counter32 · read-only · current Num of v2 sent packets from rlCdpInterfaceId | ||||
| CrlCdpInterfaceIllegalChksum | 1.3.6.1.4.1.9.6.1.101.137.19.1.8 | Counter32 | RO | |
column · Counter32 · read-only · current Num of received packets with illegal CDP checksum. | ||||
| CrlCdpInterfaceErrorPackets | 1.3.6.1.4.1.9.6.1.101.137.19.1.9 | Counter32 | RO | |
column · Counter32 · read-only · current specifies the number of received CDP packets with other error (duplicated TLVs, illegal TLVs, etc.) | ||||
| CrlCdpInterfaceMaxNeighborsExceededInMainCache | 1.3.6.1.4.1.9.6.1.101.137.19.1.10 | Counter32 | RO | |
column · Counter32 · read-only · current specifies the number of times a CDP neighbor could not be stored in the main cache. | ||||
| CrlCdpInterfaceMaxNeighborsExceededInSecondaryCache | 1.3.6.1.4.1.9.6.1.101.137.19.1.11 | Counter32 | RO | |
column · Counter32 · read-only · current specifies the number of times a CDP neighbor could not be stored in the secondary cache. | ||||
| SrlCdpInterfaceCountersClear | 1.3.6.1.4.1.9.6.1.101.137.20 | InterfaceIndexOrZero | RW | |
scalar · InterfaceIndexOrZero · read-write · current By setting the scalar to a interface id , all error and traffic counters of this interface are set to zero. To clear the counters for ALL interfaces set the scalar to 0x0FFFFFFF | ||||
| TrlCdpTlvPowerRequestTable | 1.3.6.1.4.1.9.6.1.101.137.21 | NA | ||
table · not-accessible · current The (conceptual) table contains the local advertised requested power levels
in Power Requested TLV.
indexed by rlCdpTlvPowerRequestEntry. | ||||
| RrlCdpTlvPowerRequestEntry | 1.3.6.1.4.1.9.6.1.101.137.21.1 | NA | ||
row · not-accessible · current An entry (conceptual row) in the rlCdpTlvPowerRequestTable, containing locally requested power levels advertised by CDP on one interface. Entries are available only when CDP is globally enabled, for interfaces on which CDP is enabled and the interface state is UP. | ||||
| CrlCdpTlvPowerRequestPowerLevelIndex | 1.3.6.1.4.1.9.6.1.101.137.21.1.2 | Unsigned32 (0..2147483647) | NA | |
column · Unsigned32 (0..2147483647) · not-accessible · current An index to the list of Requested-Power-Level in Power Requested TLV. | ||||
| CrlCdpTlvPowerRequestPowerLevel | 1.3.6.1.4.1.9.6.1.101.137.21.1.3 | Unsigned32 (0..2147483647) | RO | |
column · Unsigned32 (0..2147483647) · read-only · current A possible value of the Power Consumption TLV, in milliwatts | ||||
| TrlCdpSecondaryCacheAddressTable | 1.3.6.1.4.1.9.6.1.101.137.22 | NA | ||
table · not-accessible · current The (conceptual) table containing the list of network-layer addresses of a neighbor interface, as reported in the Address TLV of the most recently received CDP message and stored in the secondary cache. | ||||
| RrlCdpSecondaryCacheAddressEntry | 1.3.6.1.4.1.9.6.1.101.137.22.1 | NA | ||
row · not-accessible · current An entry (conceptual row) in the rlCdpSecondaryCacheAddressTable,
containing the list of network-layer addresses of a neighbor interface,
as reported in the Address TLV of the most recently received CDP message
and stored in the secondary cache. Entries are available only when CDP is
globally enabled, for interfaces on which CDP is enabled and the interface
state is UP. | ||||
| CrlCdpSecondaryCacheAddressIndex | 1.3.6.1.4.1.9.6.1.101.137.22.1.3 | INTEGER (0..2147483647) | NA | |
column · INTEGER (0..2147483647) · not-accessible · current The index of the address entry for a given cdpCacheIfIndex,cdpCacheDeviceIndex pair. | ||||
| CrlCdpSecondaryCacheAddressType | 1.3.6.1.4.1.9.6.1.101.137.22.1.4 | CiscoNetworkProtocol | RO | |
column · CiscoNetworkProtocol · read-only · current An indication of the type of address contained in the corresponding instance of rlCdpSecondaryCacheAddress | ||||
| CrlCdpSecondaryCacheAddress | 1.3.6.1.4.1.9.6.1.101.137.22.1.5 | CiscoNetworkAddress | RO | |
column · CiscoNetworkAddress · read-only · current A network-layer address of the device as reported in the most
recent CDP message's Address TLV. For example, if the the
corresponding instance of rlCdpSecondaryCacheAddressType had the
value 'ip(1)', then this object would be an IPv4-address. | ||||
| TrlCdpSecondaryCacheRequestedPowerTable | 1.3.6.1.4.1.9.6.1.101.137.23 | NA | ||
table · not-accessible · current The (conceptual) table containing the list of requested power levels by a remote device, as reported in the Power Requested TLV of the most recently received CDP message and stored in the secondary cache. | ||||
| RrlCdpSecondaryCacheRequestedPowerEntry | 1.3.6.1.4.1.9.6.1.101.137.23.1 | NA | ||
row · not-accessible · current An entry (conceptual row) in the rlCdpSecondaryCacheRequestedPowerTable,
containing the list of requested power levels by a remote device,
as reported in the Power Requested TLV of the most recently received CDP message
and stored in the secondary cache. Entries are available only when CDP is
globally enabled, for interfaces on which CDP is enabled and the interface
state is UP. | ||||
| CrlCdpSecondaryCacheRequestedPowerIndex | 1.3.6.1.4.1.9.6.1.101.137.23.1.3 | INTEGER (0..2147483647) | NA | |
column · INTEGER (0..2147483647) · not-accessible · current The index of the requested power level entry for a given cdpCacheIfIndex,cdpCacheDeviceIndex pair. | ||||
| CrlCdpSecondaryCacheRequestedPowerLevel | 1.3.6.1.4.1.9.6.1.101.137.23.1.4 | Unsigned32 (1..2147483647) | RO | |
column · Unsigned32 (1..2147483647) · read-only · current A requested power level in the Power Requested TLV, in milliwatts. | ||||
Textual conventions
RlCdpCounterTypesINTEGERerrorPackets(8)illegalChksum(7)maxNeighborsExceededInMainCache(9)maxNeighborsExceededInSecondaryCache(10)totalInputPackets(1)totalOutputPackets(4)v1InputPackets(2)v1OutputPackets(5)v2InputPackets(3)v2OutputPackets(6)v1OutputPackets counter specifies the number of sent CDP packets with version 1 v2OutputPackets counter specifies the number of sent CDP packets with version 2 v1InputPackets counter specifies the number of received CDP packets with version 1 v2InputPackets counter specifies the number of received CDP packets with version 2 totalInputPackets counter specifies the total number of received CDP packets totalOutputPackets counter specifies the total number of sent CDP packets illegalChksum counter specifies the number of received CDP packets with illegal checksum. errorPackets counter specifies the number of received CDP packets with other error (duplicated TLVs, illegal TLVs, etc.) maxNeighborsExceededInMainCache counter specifies the number of times a CDP neighbor could not be stored in the main cache. maxNeighborsExceededInSecondaryCache specifies counter the number of times a CDP neighbor could not be stored in the secondary cache.
RlCdpPduActionTypesINTEGERbridging(2)filtering(1)flooding(3)filtering - CDP packets would filtered (dropped). bridging - CDP packets bridged as regular data packets
RlCdpVersionTypesINTEGERversion-v1(1)version-v2(2)version-v1 - cdp version 1 version-v2 - cdp version 2
Traps / Notifications
- rlCdpLogMismatchDuplexTrap
1.3.6.1.4.1.9.6.1.101.0.224 - rlCdpLogMismatchNativeVlanTrap
1.3.6.1.4.1.9.6.1.101.0.226 - rlCdpLogMismatchVoiceVlanTrap
1.3.6.1.4.1.9.6.1.101.0.225