MIB Browser

CISCO-RESILIENT-ETHERNET-PROTOCOL-MIB

ciscoSystems
This MIB module defines objects required for managing
Resilient Ethernet Protocol (REP).

Resilient Ethernet Protocol (REP) is a Cisco proprietary
protocol that provides an alternative to Spanning Tree
Protocol (STP) to control network loops, handle link
failures and improve convergence time.

REP controls a group of ports connected in a segment;
ensures that the segment does not create any bridging loops,
and responds to link failures within the segment.

The following diagram depicts a REP segment:

[Sw E1]E---NE[Sw 1]NE---NE[Sw 2]NE.........
                                          .
                                          .
[Sw E2]E---NE[Sw N]NE---NE[Sw N-1]NE.......

Sw : Switch.
E  : Edge port.
NE : Non-Edge port.
E1/E2: Edge switches.  E1 and E2 can either be same or
different switches.

A REP segment is a chain of ports connected to each other
and configured with a segment identifier.  Each segment
consists of standard (non-edge) segment ports and up to
two edge ports.  A device can have only two ports that
belong to the same segment, and each segment port can have
only one external neighbor.

One edge port in a REP segment acts as the primary edge
port; the other as the secondary edge port.  It is the primary
edge port that always participates in VLAN load balancing in
a REP segment.  REP VLAN load balancing is achieved by blocking
some VLANs at a configured alternate port and all other VLANs at
an edge port.  The execution (preemption) of VLAN load balancing
is triggered by manually enforcing it or after a pre-defined
delay, after the REP segment is complete.

When segment is completed, all ports will be in open state
except one port that can be in alternate state that is used for
VLAN load balancing as explained above.
Organization
Cisco Systems, Inc.
Root OID
1.3.6.1.4.1.9.9.601
Last updated
Objects
72
Source
Show full MIB
snmptranslate -m CISCO-RESILIENT-ETHERNET-PROTOCOL-MIB -Tp
snmpwalk -v2c -c <community> -m CISCO-RESILIENT-ETHERNET-PROTOCOL-MIB <host> 1.3.6.1.4.1.9.9.601

Imports

CISCO-SMIciscoMgmt
CISCO-TCCiscoVlanList
IF-MIBInterfaceIndex, InterfaceIndexOrZero
Q-BRIDGE-MIBVlanId
SNMPv2-CONFMODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP
SNMPv2-SMIBits, Counter32, Integer32, IpAddress, MODULE-IDENTITY, MibIdentifier, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, iso
SNMPv2-TCDisplayString, PhysAddress, RowStatus, TEXTUAL-CONVENTION, TimeStamp, TruthValue

OID tree

NameOIDTypeAccessStatusExample
IciscoResilientEthernetProtocolMIB1.3.6.1.4.1.9.9.601
NciscoRepMIBNotifs1.3.6.1.4.1.9.9.601.0
!crepLinkStatus1.3.6.1.4.1.9.9.601.0.1
!crepPreemptionStatus1.3.6.1.4.1.9.9.601.0.2
!crepPortRoleChange1.3.6.1.4.1.9.9.601.0.3
NciscoRepMIBObjects1.3.6.1.4.1.9.9.601.1
NcrepGlobalInfo1.3.6.1.4.1.9.9.601.1.1
ScrepVersion1.3.6.1.4.1.9.9.601.1.1.1Integer32RO
ScrepAdminVlan1.3.6.1.4.1.9.9.601.1.1.2VlanIdRW
ScrepNotifsEnable1.3.6.1.4.1.9.9.601.1.1.3TruthValueRW
ScrepGlobalRepNotifsRate1.3.6.1.4.1.9.9.601.1.1.4Unsigned32 (0..1000)RW
ScrepMinSegmentId1.3.6.1.4.1.9.9.601.1.1.5RepSegmentIdRO
ScrepMaxSegmentId1.3.6.1.4.1.9.9.601.1.1.6RepSegmentIdRO
NcrepInterfaceConfig1.3.6.1.4.1.9.9.601.1.2
TcrepInterfaceConfigTable1.3.6.1.4.1.9.9.601.1.2.1NA
RcrepInterfaceConfigEntry1.3.6.1.4.1.9.9.601.1.2.1.1NA
CcrepIfIndex1.3.6.1.4.1.9.9.601.1.2.1.1.1InterfaceIndexNA
CcrepIfSegmentId1.3.6.1.4.1.9.9.601.1.2.1.1.2RepSegmentIdRC
CcrepIfOperStatus1.3.6.1.4.1.9.9.601.1.2.1.1.3INTEGERRO
CcrepIfPortRole1.3.6.1.4.1.9.9.601.1.2.1.1.4INTEGERRO
CcrepIfPortID1.3.6.1.4.1.9.9.601.1.2.1.1.5OCTET STRING (SIZE (8))RO
CcrepIfAdminEdgePortType1.3.6.1.4.1.9.9.601.1.2.1.1.6RepPortTypeRC
CcrepIfOperEdgePortType1.3.6.1.4.1.9.9.601.1.2.1.1.7RepPortTypeRO
CcrepIfPreferredConfig1.3.6.1.4.1.9.9.601.1.2.1.1.8TruthValueRC
CcrepifBlockedVlans1k1.3.6.1.4.1.9.9.601.1.2.1.1.9CiscoVlanListRC
CcrepifBlockedVlans2k1.3.6.1.4.1.9.9.601.1.2.1.1.10CiscoVlanListRC
CcrepifBlockedVlans3k1.3.6.1.4.1.9.9.601.1.2.1.1.11CiscoVlanListRC
CcrepifBlockedVlans4k1.3.6.1.4.1.9.9.601.1.2.1.1.12CiscoVlanListRC
CcrepLoadBalanceBlockPortType1.3.6.1.4.1.9.9.601.1.2.1.1.13INTEGERRC
CcrepBlockPortNumInfo1.3.6.1.4.1.9.9.601.1.2.1.1.14Integer32 (-256..256)RC
CcrepBlockPortIdInfo1.3.6.1.4.1.9.9.601.1.2.1.1.15OCTET STRING (SIZE (8))RC
CcrepIfPreemptDelayTimer1.3.6.1.4.1.9.9.601.1.2.1.1.16Integer32 (-1..300)RC
CcrepIfStcnPropagateToSTP1.3.6.1.4.1.9.9.601.1.2.1.1.17TruthValueRC
CcrepIfStcnPropagateToOtherSegs1.3.6.1.4.1.9.9.601.1.2.1.1.18RepSegmentListRC
CcrepIfStcnPropagateToIf1.3.6.1.4.1.9.9.601.1.2.1.1.19InterfaceIndexOrZeroRC
CcrepIfConfigRowStatus1.3.6.1.4.1.9.9.601.1.2.1.1.20RowStatusRC
TcrepInterfaceStatsTable1.3.6.1.4.1.9.9.601.1.2.2NA
RcrepInterfaceStatsEntry1.3.6.1.4.1.9.9.601.1.2.2.1NA
CcrepCounterDiscontinuityTime1.3.6.1.4.1.9.9.601.1.2.2.1.1TimeStampRO
CcrepLslRxPdus1.3.6.1.4.1.9.9.601.1.2.2.1.2Counter32RO
CcrepLslTxPdus1.3.6.1.4.1.9.9.601.1.2.2.1.3Counter32RO
CcrepHflRxPdus1.3.6.1.4.1.9.9.601.1.2.2.1.4Counter32RO
CcrepHflTxPdus1.3.6.1.4.1.9.9.601.1.2.2.1.5Counter32RO
CcrepBpaTlvRxPackets1.3.6.1.4.1.9.9.601.1.2.2.1.6Counter32RO
CcrepBpaTlvTxPackets1.3.6.1.4.1.9.9.601.1.2.2.1.7Counter32RO
CcrepBpaStcnLslRxPackets1.3.6.1.4.1.9.9.601.1.2.2.1.8Counter32RO
CcrepBpaStcnLslTxPackets1.3.6.1.4.1.9.9.601.1.2.2.1.9Counter32RO
CcrepBpaStcnHflRxPackets1.3.6.1.4.1.9.9.601.1.2.2.1.10Counter32RO
CcrepBpaStcnHflTxPackets1.3.6.1.4.1.9.9.601.1.2.2.1.11Counter32RO
CcrepEpaElectionTlvRxPackets1.3.6.1.4.1.9.9.601.1.2.2.1.12Counter32RO
CcrepEpaElectionTlvTxPackets1.3.6.1.4.1.9.9.601.1.2.2.1.13Counter32RO
CcrepEpaCommandTlvRxPackets1.3.6.1.4.1.9.9.601.1.2.2.1.14Counter32RO
CcrepEpaCommandTlvTxPackets1.3.6.1.4.1.9.9.601.1.2.2.1.15Counter32RO
CcrepEpaInfoTlvRxPackets1.3.6.1.4.1.9.9.601.1.2.2.1.16Counter32RO
CcrepEpaInfoTlvTxPackets1.3.6.1.4.1.9.9.601.1.2.2.1.17Counter32RO
NcrepSegmentConfig1.3.6.1.4.1.9.9.601.1.3
TcrepSegmentTable1.3.6.1.4.1.9.9.601.1.3.1NA
RcrepSegmentEntry1.3.6.1.4.1.9.9.601.1.3.1.1NA
CcrepSegmentId1.3.6.1.4.1.9.9.601.1.3.1.1.1RepSegmentIdNA
CcrepSegmentInterface11.3.6.1.4.1.9.9.601.1.3.1.1.2InterfaceIndexRO
CcrepSegmentInterface21.3.6.1.4.1.9.9.601.1.3.1.1.3InterfaceIndexOrZeroRO
CcrepSegmentComplete1.3.6.1.4.1.9.9.601.1.3.1.1.4TruthValueRO1
CcrepSegmentPreempt1.3.6.1.4.1.9.9.601.1.3.1.1.5TruthValueRW
CcrepSegmentPreemptStatus1.3.6.1.4.1.9.9.601.1.3.1.1.6INTEGERRO
NciscoRepMIBConform1.3.6.1.4.1.9.9.601.2
NciscoRepMIBCompliances1.3.6.1.4.1.9.9.601.2.1
MciscoRepMIBCompliance1.3.6.1.4.1.9.9.601.2.1.1
NciscoRepMIBGroups1.3.6.1.4.1.9.9.601.2.2
GciscoRepGlobalGroup1.3.6.1.4.1.9.9.601.2.2.1
GciscoRepInterfaceGroup1.3.6.1.4.1.9.9.601.2.2.2
GciscoRepNotificationGroup1.3.6.1.4.1.9.9.601.2.2.3
GciscoRepSegmentGroup1.3.6.1.4.1.9.9.601.2.2.4

Textual conventions

RepPortType INTEGER

edge(2) edgeNoNeighbor(4) edgeNoNeighborPrimary(5) edgePrimary(3) notEdge(1)

This TC describes the port type of the REP port.

'notEdge'     - non-edge Port.

'edge'        - edge port for the segment.

'edgePrimary' - primary edge port for the segment.

'edgeNoNeighbor'        - no neighbor edge port for the
segment.

'edgeNoNeighborPrimary' - primary no neighbor edge port for the
segment.
RepSegmentId Unsigned32
This TC describes an object to provide the unique
identifier for the REP segment.
RepSegmentList OCTET STRING
This TC describes an object that indicates the list
of REP segments.  Each octet within this value specifies
a set of eight segments.  The first octet represents the
first 8 segments of the range of segments specified by
the object, the second octet represents the next 8 segments
etc.

Within each octet, the most significant bit represents
the lowest numbered segment, and the least significant bit
represents the highest numbered segment.  If that bit has
a value of '1' then that segment is included in the set of
segments; the segment is not included if its bit has a value
of '0'.

NMS may omit any zero-valued octets from the end of this string
in order to reduce SetPDU size, and the agent may also omit
zero-valued trailing octets, to reduce the size of GetResponse
PDUs.

The maximum length of the object that uses this TC is calculated
to be the ceiling whole number of
((crepMaxSegmentId - crepMinSegmentId + 1) / 8).
Any octets beyond this length in the SetPDU should be ignored.

Traps / Notifications

Groups and compliance