MIB Browser

CISCO-LWAPP-TC-MIB

ciscoSystems
This module defines textual conventions used
throughout the Cisco enterprise MIBs
designed for implementation on Central
Controllers that terminate the Light Weight
Access Point Protocol from LWAPP Access
Points.

The relationship between CC and the LWAPP APs
can be depicted as follows:

+......+     +......+     +......+           +......+
+      +     +      +     +      +           +      +
+  CC  +     +  CC  +     +  CC  +           +  CC  +
+      +     +      +     +      +           +      +
+......+     +......+     +......+           +......+
..            .             .                 .
..            .             .                 .
.  .            .             .                 .
.    .            .             .                 .
.      .            .             .                 .
.        .            .             .                 .
+......+ +......+     +......+      +......+          +......+
+      + +      +     +      +      +      +          +      +
+  AP  + +  AP  +     +  AP  +      +  AP  +          +  AP  +
+      + +      +     +      +      +      +          +      +
+......+ +......+     +......+      +......+          +......+
.              .             .                 .
.  .              .             .                 .
.    .              .             .                 .
.      .              .             .                 .
.        .              .             .                 .
+......+ +......+     +......+      +......+          +......+
+      + +      +     +      +      +      +          +      +
+  MN  + +  MN  +     +  MN  +      +  MN  +          +  MN  +
+      + +      +     +      +      +      +          +      +
+......+ +......+     +......+      +......+          +......+


The LWAPP tunnel exists between the controller and
the APs.  The MNs communicate with the APs through
the protocol defined by the 802.11 standard.

LWAPP APs, upon bootup, discover and join one of the
controllers and the controller pushes the configuration,
that includes the WLAN parameters, to the LWAPP APs.
The APs then encapsulate all the 802.11 frames from
wireless clients inside LWAPP frames and forward
the LWAPP frames to the controller.

                GLOSSARY

Access Point ( AP )

An entity that contains an 802.11 medium access
control ( MAC ) and physical layer ( PHY ) interface
and provides access to the distribution services via
the wireless medium for associated clients.

LWAPP APs encapsulate all the 802.11 frames in
LWAPP frames and sends it to the controller to which
it is logically connected.

Advanced Encryption Standard ( AES )

In cryptography, the Advanced Encryption Standard
(AES), also known as Rijndael, is a block cipher
adopted as an encryption standard by the US
government. It is expected to be used worldwide
and analysed extensively, as was the case with its
predecessor, the Data Encryption Standard (DES).
AES was adopted by National Institute of Standards
and Technology (NIST) as US FIPS PUB 197 in
November 2001 after a 5-year standardisation
process.

Central Controller ( CC )

The central entity that terminates the LWAPP protocol
tunnel from the LWAPP APs.  Throughout this MIB,
this entity is also referred to as 'controller'.

Light Weight Access Point Protocol ( LWAPP )

This is a generic protocol that defines the
communication between the Access Points and the
Central Controller.

Management Frame Protection ( MFP )

A proprietary mechanism devised to integrity protect
the otherwise unprotected management frames of the
802.11 protocol specification.

Message Integrity Check ( MIC )

A checksum computed on a sequence of bytes and made
known to the receiving party in a data communication,
to let the receiving party make sure the bytes
received were not compromised enroute.

Mobile Node ( MN )

A roaming 802.11 wireless device in a wireless
network associated with an access point.

Temporal Key Integrity Protocol ( TKIP )

A security protocol defined to enhance the limitations
of WEP.  Message Integrity Check and per-packet keying
on all WEP-encrypted frames are two significant
enhancements provided by TKIP to WEP.

Wired Equivalent Privacy ( WEP )

A security method defined by 802.11. WEP uses a
symmetric key stream cipher called RC4 to encrypt the
data packets.

802.11n

802.11n builds upon previous 802.11 standards by
adding MIMO (multiple-input multiple-output). MIMO
uses multiple transmitter and receiver antennas to
allow for increased data throughput through spatial
multiplexing and increased range.

Control/Extension Channel

A single 802.11 channel is 20 MHz wide.  802.11n allows
the use of channels of width 40 MHz by combining two
20 MHz channels.  The channels are known as the primary
or control channel and secondary or extension channel.
Both the channels are used for transmission
and reception of data.

REFERENCE

[1] Part 11 Wireless LAN Medium Access Control ( MAC )
    and Physical Layer ( PHY ) Specifications.

[2] Draft-obara-capwap-lwapp-00.txt, IETF Light
    Weight Access Point Protocol.

[3] Enhanced Wireless Consortium MAC Specification,
    v1.24.

[4] Enhanced Wireless Consortium PHY Specification,
    v1.27.
Organization
Cisco Systems, Inc.
Root OID
1.3.6.1.4.1.9.9.514
Last updated
Objects
1
Source
Show full MIB
snmptranslate -m CISCO-LWAPP-TC-MIB -Tp
snmpwalk -v2c -c <community> -m CISCO-LWAPP-TC-MIB <host> 1.3.6.1.4.1.9.9.514

Imports

CISCO-SMIciscoMgmt
SNMPv2-CONFMODULE-COMPLIANCE, NOTIFICATION-GROUP
SNMPv2-SMIBits, Gauge32, Integer32, IpAddress, MODULE-IDENTITY, MibIdentifier, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, iso
SNMPv2-TCDisplayString, PhysAddress, TEXTUAL-CONVENTION

OID tree

NameOIDTypeAccessStatus
IciscoLwappTextualConventions1.3.6.1.4.1.9.9.514

Textual conventions

CLApAssocFailureReason INTEGER

notSupported(2) unknown(1)

This textual convention defines the possible reasons
for an AP's failure to get associated to a controller.

The semantics are as follows:

unknown - The reason for the AP not being able to
associate is unknown.

notSupported - The AP is not supported for management
by the controller.
CLApDot11RadioRole INTEGER

access(4) downlink(3) downlinkAccess(6) shutdown(0) unknown(8) upDownlink(1) upDownlinkAccess(7) uplink(2) uplinkAccess(5)

This textual convention defines the possible values
of role a radio can support.
shutdown(0)         - This role states that the radio is
                      shut down.
upDownlink(1)       - This radio provides both uplink
                      and downlink access.
uplink(2)           - This role is applicable only for Ethernet
                      ports. This radio provides uplink access.
downlink(3)         - This radio provides downlink access.
                      downlink radio allows child APs to join.
access(4)           - This radio provides the access to the
                      clients.
uplinkAccess(5)     - This radio role states that the radio
                      provides the uplink access to the clients.
downlinkAccess(6)   - This radio role states that the radio
                      provides the downlink access to
                      the clients.
upDownlinkAccess(7) - This radio role states that the radio
                      provides both uplink and downlink access
                      to the clients.
unknown(8)          - This radio role is unknown.
CLApDot11RadioSubband INTEGER

all(1) sub49(2) sub52(3) sub54(4) sub58(5)

This textual convention defines the possible values
of subbands a radio can support.
Currently, this information is applicable to
A radios.
all(1) - This radio is a regular A radio that operates
         in the full A band spectrum in the frequency
         range 4940 Mhz - 5850 Mhz.
sub49(2) - This is an A radio that operates only in the
           public safety (4.9 Ghz) sub band in the
           frequency range 4940 Mhz - 5100 Mhz.
sub52(3) - This is an A radio that operates only in the
           5.2 Ghz sub band in the frequency range
           5250 Mhz - 5350 Mhz.
sub54(4) - This is an A radio that operates only in the
           5.4 Ghz sub band in the frequency range
           5470 Mhz - 5725 Mhz.
sub58(5) - This is an A radio that operates only in the
           5.8 Ghz sub band in the frequency range
           5725 Mhz - 5850 Mhz.
CLApIfType INTEGER

dot11-6ghz(6) dot11-xor-5-6ghz(7) dot11a(2) dot11abgn(4) dot11bg(1) rlan(5) uwb(3)

This textual convention defines the type of a
       wireless interface.

       The semantics are as follows:

       dot11bg - This value indicates that the radio
       interface follows 802.11b or 802.11g standard.

       dot11a  - This value indicates that the radio
       interface follows 802.11a standard.

       dot11abgn  - This value indicates that the radio
       interface is operating in XOR mode between 802.11a
       and 802.11bg.

       uwb - This value indicates that this is a Ultra
       Wideband Interface.

       rlan - This value indicates that this is a RLAN
interface.

       dot11_6ghz - This value indicates that the radio
interface is following 802.11 6ghz standard.

dot11_xor_5_6ghz - This value indicates that the
radio interface is operating in XOR mode between
802.11a and 802.11 6ghz.
CLApMode INTEGER

bridge(5) local(0) monitor(1) remote(2) remoteBridge(7) remoteHybrid(8) rogueDetector(3) seConnect(6) sensor(9) sniffer(4)

This textual convention defines the working
mode of the AP.
local(0) -        This mode enables the access points
                  to serve the clients.
monitor(1) -      This mode enables the access points
                  to monitor all of its cycles scanning
                  the channels and looking for rogues.
remote(2) -       This mode indicates that AP is a remote
                  edge lightweight access point.
rogueDetector(3)- This mode enables the access points
                  to detect the rogue access points.
sniffer(4) -      This mode enables the access points
                  to sniff packets in a particular channel.
bridge(5) -       This mode indicates that a root access point.
                  is connected
seConnect(6) -    This mode enables the access points
                  to join Cisco spectrum expert and
                  perform spectrum intelligence.
remoteBridge(7) - This mode indicates that AP is a remote
                  edge lightweight access point in Bridge
                  (Flex + Mesh) mode.
 remoteHybrid(8) - This mode is currently not used.
 sensor(9)       - This mode indicates the radio inside
                   the access point to function as a
                   dedicated sensor.
CLApNtpStatus INTEGER

authFail(7) none(2) notSuitable(8) notSynched(5) notValid(1) synched(4) unknown(9) unreachable(3) waitSynch(6)

This textual convention defines the NTP status.
The semantics are as follows:

notValid - This value indicates NTP status is not valid.

none  - This value indicates NTP status is not received.

unreachable  - This value indicates that NTP server is not
reachable.

synched  - This value indicates NTP server is syched.

notSynched  - This value indicates NTP server is not sycnhed.

waitSynch  - This value indicates NTP server is waiting to be sycnhed.

authFail  - This value indicates NTP server authentication failed.

notSuitable  - This value indicates NTP server is not suitable for AP.
CLCdpAdvtVersionType INTEGER

cdpv1(1) cdpv2(2)

This textual convention lists the versions of
the CDP protocol in use in LWAPP APs and Controllers.
CLClientPowerSaveMode INTEGER

active(1) powersave(2)

This textual convention defines power management mode
of this client.
The possible two modes are:
active(1)    - The client is not in power-save mode
               and it is actively sending or receiving
               data.
powersave(2) - The client is in power-save mode and it
               wakes up once a while to check for
               pending data.
CLDot11Band INTEGER

band2dot4(1) band5(2) maui-6ghz(3)

This textual convention defines the 802.11 frequency
band.

The semantics are as follows:

band2dot4 - This value indicates that the
2.4 GHz band is in use.

band5 - This value indicates that the
5 GHz band is in use.

maui-6ghz - This value indicates that the
6 GHz band is in use.
CLDot11Channel Unsigned32 (1..14 | 34 | 36 | 38 | 40 | 42 | 44 | 46 | 48 | 52 | 56 | 60 | 64 | 149 | 153 | 157 | 161)
This textual convention defines the possible channel
numbers in an 802.11 communication channel.  The
802.11 radio interface of an Access Point operates
in one of the possible channels at any point of time
for wireless data communication with 802.11 based
wireless clients.
CLDot11ChannelBandwidth INTEGER

aboveforty(4) belowforty(5) five(1) ten(2) twenty(3)

This textual convention defines the channel
bandwidth for 802.11n radio interfaces.

The semantics are as follows:

five - This value indicates that the bandwidth
is 5 MHz.

ten - This value indicates that the bandwidth
is 10 MHz.

twenty - This value indicates that the bandwidth
is 20 MHz.

aboveforty - This value indicates that the bandwidth
is 40 MHz with the extension channel above the control
channel.

belowforty - This value indicates that the bandwidth
is 40 MHz with the extension channel below the control
channel.
CLDot11ClientStatus INTEGER

aaaPending(2) associated(4) authenticated(3) disassociated(6) excluded(9) idle(1) powersave(5) probing(8) tobedeleted(7)

This textual convention defines the states
of an 802.11 client.

The semantics are as follows:

idle(1) - client is in idle mode.

aaaPending(2) - client's authentication is pending.
Request has been sent to AAA server for authentication.

authenticated(3) - client has been authenticated.

associated(4) - client is associated, but not
authenticated.

powersave(5) - client is in powersave mode.

disassociated(6) - client has dissociated and not in
any of the 802.11 networks managed by the controller.

tobedeleted(7) - client is marked for deletion.

probing(8) - state before association. The client
will be removed if it does not associate.

excluded(9) - client has been marked as excluded after fixed
number of authentication failures.
CLDot11RfParamMode INTEGER

auto(3) custom(2) default(1)

This textual convention defines how the RF
parameters used to manage roaming are chosen
by the controller.

default - controller reverts back to the default
values specified for the RF parameters.

auto - controller determines the RF parameters
automatically without any input from the end user.

custom - controller uses the RF parameters
configured by the end user.  User is allowed to
configure the parameters only if the mode is set
to 'custom'.
CLEventFrames Bits

cLAssocRequestFrm(0) cLAssocResponseFrm(1) cLAtimFrm(9) cLAuthenticationFrm(11) cLBeaconFrm(8) cLDeAuthenticationFrm(12) cLDissociationFrm(10) cLProbeRequestFrm(4) cLProbeResponseFrm(5) cLReAssocRequestFrm(2) cLReAssocResponseFrm(3) cLReserved1(6) cLReserved2(7)

This textual convention defines the possible
802.11 management frame subtypes.

cLAssocRequestFrm - 802.11 Association Request
frame

cLAssocResponseFrm - 802.11 Association Response
frame

cLReAssocRequestFrm - 802.11 Reassociation
Request frame

cLReAssocResponseFrm - 802.11 Reassociation
Response frame

cLProbeRequestFrm - 802.11 Probe Request frame

cLProbeResponseFrm - 802.11 Probe Response
frame

cLReserved1 - Reserved for future use

cLReserved2 - Reserved for future use

cLBeaconFrm - 802.11 Beacon frame

cLAtimFrm - 802.11 Adhoc Traffic Indication
Map frame

cLDissociationFrm - 802.11 Dissociation
frame

cLAuthenticationFrm - 802.11 Authentication
frame

cLDeAuthenticationFrm - 802.11 Deauthentication
frame
CLMfpEventSource INTEGER

clientMfp(2) infrastructureMfp(1)

The source of the MFP anomaly event.

infrastructureMfp - The source of the MFP event is
an infrastructure device that implements MFP.

clientMfp - The source of the MFP event is a client
device that implements MFP.
CLMfpEventType INTEGER

bcastActionFrameRcvd(34) bcastDeauthenticationFrameRcvd(33) bcastDisassociationFrameRcvd(32) ccmpDecryptError(17) ccmpInvalidReplayCtr(19) ccmpNoEncryptError(16) invalidMic(1) invalidSeq(2) noMic(3) tkipInvalidIcv(21) tkipInvalidMhdrIe(23) tkipInvalidMic(22) tkipInvalidReplayCtr(24) tkipNoEncryptError(20) unexpectedMic(4)

The type of the MFP anomaly event.

invalidMic - The MFP Validation has identified
that the MIC carried by a particular management
frame is invalid.

invalidSeq - The MFP validation has identified
that a particular management frame is carrying an
invalid sequence number.  Note that an invalid
sequence number error can also be detected due to an
incorrect timestamp in the MFP information element.
The incorrect timestamp could possibly be due to the
fact that the detecting AP's time window is not in
synchronization with that of other APs in the
MFP framework.

noMic - The MFP validation has detected a management
frame without the MFP information element.

unexpectedMic - The MFP validation has detected a
management frame as carrying a MIC value when
protection is not enabled on the WLAN.

ccmpDecryptError - An MFP frame that was apparently
received from a client in an AES-CCMP encrypted
session was rejected by the Access Point because it
could not be decrypted.

ccmpInvalidMhdrIe - An MFP frame that was apparently
received from a client in an AES-CCMP encrypted
session was rejected by the Access Point because it
contained an invalid MHDR information element, or the
MHDR information element was not present.

ccmpInvalidReplayCtr - An MFP frame that was apparently
received from a client in an AES-CCMP encrypted session
was rejected by the Access Point because the replay
counter was not valid.

tkipInvalidIcv - An MFP frame that was apparently
received from a client in a TKIP encrypted session was
rejected by the Access Point because it contained an
invalid Integrity Check Value.

tkipInvalidMic - An MFP frame that was apparently
received from a client in a TKIP encrypted session was
rejected by the Access Point because the message
integrity check failed.

tkipInvalidMhdrIe - An MFP frame that was apparently
received from a client in a TKIP encrypted session was
rejected by the Access Point because it contained an
invalid MHDR information element, or the MHDR
information element was not present.

tkipInvalidReplayCtr - An MFP frame that was apparently
received from a client in a TKIP encrypted session was
rejected by the Access Point because it the replay
counter was not valid.

bcastDisassociationFrameRcvd - The Access Point detected
a broadcast disassociation frame.  Broadcast
disassociation frames are rejected by CCXv5 compliant
devices.

bcastDeauthenticationFrameRcvd - The Access Point
detected a broadcast deauthentication frame.  Broadcast
deauthentication frames are rejected by CCXv5 compliant
devices.

bcastActionFrameRcvd - The Access Point detected a
broadcast action frame.  Broadcast action frames are
rejected by CCXv5 compliant devices.
CLMfpVersion INTEGER

mfpv1(1) mfpv2(2)

This textual convention lists the versions of
the MFP protocol.
CLSecEncryptType Bits

aes(1) tkip(0)

This textual convention defines the type of
encryption to be applied to a WLAN.

The semantics are as follows:

tkip - This value indicates that TKIP encryption
is configured for data protection.

aes  - This value indicates that AES encryption
is configured for data protection.
CLSecKeyFormat INTEGER

ascii(3) default(1) hex(2)

This textual convention defines the type of
the key configured for encryption.
CLTimeBaseStatus INTEGER

cTimeBaseInSync(1) cTimeBaseNotInSync(2)

This textual convention is used to define the
time synchronization of entities with their
respective time bases.

cTimeBaseInSync - This value indicates that the
respective entity is in synchronization with
its time base.

cTimeBaseNotInSync - This value indicates that
the respective entity is not in synchronization
with its time base.
CLTsmDot11CurrentPackets Gauge32
The number of packets received over a specified
period of time.
CLWebAuthType INTEGER

external(3) internalCustom(2) internalDefault(1)

Represents either one of the following web auth types
internalDefault(1) -
        The default login page will be
presented to the client for authentication.

internalCustom(2)  -
        The administrator has created and
uploaded a custom login page and it will be
presented to the clients for authentication.

external(3) -
        This value indicates that the login page
will be served from the external web server.  Note
that cLWAWebAuthType can be successfully set to this
value when the cLWAExternalWebAuthURL object has been
set to string with non-zero length.
CcxServiceVersion INTEGER

none(1) version1(2) version2(3)

This textual convention defines the service versions
supported by a CCX Next client. The supported services
include foundation, location, management and voice.
Dscp INTEGER (0..63)
An integer that is in the range of the diffserv codepoint
values.

Used by