CISCO-LWAPP-RF-MIB
ciscoSystemsThis MIB is intended to be implemented on all those
devices operating as Central Controllers (CC) that
terminate the Light Weight Access Point Protocol
tunnel from Cisco Light-weight LWAPP Access Points.
This MIB helps to manage the Radio Frequency (RF)
parameters on the controller.
The relationship between CC and the LWAPP APs
can be depicted as follows:
+......+ +......+ +......+ +......+
+ + + + + + + +
+ CC + + CC + + CC + + CC +
+ + + + + + + +
+......+ +......+ +......+ +......+
.. . . .
.. . . .
. . . . .
. . . . .
. . . . .
. . . . .
+......+ +......+ +......+ +......+ +......+
+ + + + + + + + + +
+ AP + + AP + + AP + + AP + + AP +
+ + + + + + + + + +
+......+ +......+ +......+ +......+ +......+
. . . .
. . . . .
. . . . .
. . . . .
. . . . .
+......+ +......+ +......+ +......+ +......+
+ + + + + + + + + +
+ MN + + MN + + MN + + MN + + MN +
+ + + + + + + + + +
+......+ +......+ +......+ +......+ +......+
The LWAPP tunnel exists between the controller and
the APs. The MNs communicate with the APs through
the protocol defined by the 802.11 standard.
LWAPP APs, upon bootup, discover and join one of the
controllers and the controller pushes the configuration,
that includes the WLAN parameters, to the LWAPP APs.
The APs then encapsulate all the 802.11 frames from
wireless clients inside LWAPP frames and forward
the LWAPP frames to the controller.
GLOSSARY
Access Point ( AP )
An entity that contains an 802.11 medium access
control ( MAC ) and physical layer ( PHY ) interface
and provides access to the distribution services via
the wireless medium for associated clients.
LWAPP APs encapsulate all the 802.11 frames in
LWAPP frames and sends it to the controller to which
it is logically connected to.
Central Controller ( CC )
The central entity that terminates the LWAPP protocol
tunnel from the LWAPP APs. Throughout this MIB,
this entity also referred to as 'controller'.
Light Weight Access Point Protocol ( LWAPP )
This is a generic protocol that defines the
communication between the Access Points and the
controllers.
Mobile Node ( MN )
A roaming 802.11 wireless device in a wireless
network associated with an access point.
802.1x
The IEEE ratified standard for enforcing port based
access control. This was originally intended for
use on wired LANs and later extended for use in
802.11 WLAN environments. This defines an
architecture with three main parts - a supplicant
(Ex. an 802.11 wireless client), an authenticator
(the AP) and an authentication server(a Radius
server). The authenticator passes messages back
and forth between the supplicant and the
authentication server to enable the supplicant
get authenticated to the network.
Radio Frequency ( RF )
Radio frequency (RF) is a rate of oscillation in the
range of about 3 kHz to 300 GHz, which corresponds to
the frequency of radio waves, and the
alternating currents which carry radio signals.
Received Signal Strength Indicator ( RSSI )
A measure of the strength of the signal as
observed by the entity that received it,
expressed in 'dbm'.
Coverage Hole Detection ( CHD )
If clients on an Access Point are detected at low
RSSI levels, it is considered a coverage hole
by the Access Points. This indicates the existence
of an area where clients are continually getting poor
signal coverage, without having a viable location to
roam to.
REFERENCE
[1] Wireless LAN Medium Access Control ( MAC ) and
Physical Layer ( PHY ) Specifications.
[2] Draft-obara-capwap-lwapp-00.txt, IETF Light
Weight Access Point Protocol
[3] IEEE 802.11 - The original 1 Mbit/s and 2 Mbit/s,
2.4 GHz RF and IR standard.snmptranslate -m CISCO-LWAPP-RF-MIB -Tpsnmpwalk -v2c -c <community> -m CISCO-LWAPP-RF-MIB <host> 1.3.6.1.4.1.9.9.778Imports
| CISCO-LWAPP-TC-MIB | CLApIfType |
|---|---|
| CISCO-LWAPP-WLAN-MIB | cLAPGroupName |
| CISCO-SMI | ciscoMgmt |
| SNMP-FRAMEWORK-MIB | SnmpAdminString |
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP |
| SNMPv2-SMI | Bits, Integer32, IpAddress, MODULE-IDENTITY, MibIdentifier, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, iso |
| SNMPv2-TC | DisplayString, PhysAddress, RowStatus, StorageType, TEXTUAL-CONVENTION, TruthValue |
OID tree
| Name | OID | Type | Access | Status | Example | ||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| IciscoLwappRFMIB | 1.3.6.1.4.1.9.9.778 | ||||||||||||||||||||
identity This MIB is intended to be implemented on all those
devices operating as Central Controllers (CC) that
terminate the Light Weight Access Point Protocol
tunnel from Cisco Light-weight LWAPP Access Points.
This MIB helps to manage the Radio Frequency (RF)
parameters on the controller.
The relationship between CC and the LWAPP APs
can be depicted as follows:
+......+ +......+ +......+ +......+
+ + + + + + + +
+ CC + + CC + + CC + + CC +
+ + + + + + + +
+......+ +......+ +......+ +......+
.. . . .
.. . . .
. . . . .
. . . . .
. . . . .
. . . . .
+......+ +......+ +......+ +......+ +......+
+ + + + + + + + + +
+ AP + + AP + + AP + + AP + + AP +
+ + + + + + + + + +
+......+ +......+ +......+ +......+ +......+
. . . .
. . . . .
. . . . .
. . . . .
. . . . .
+......+ +......+ +......+ +......+ +......+
+ + + + + + + + + +
+ MN + + MN + + MN + + MN + + MN +
+ + + + + + + + + +
+......+ +......+ +......+ +......+ +......+
The LWAPP tunnel exists between the controller and
the APs. The MNs communicate with the APs through
the protocol defined by the 802.11 standard.
LWAPP APs, upon bootup, discover and join one of the
controllers and the controller pushes the configuration,
that includes the WLAN parameters, to the LWAPP APs.
The APs then encapsulate all the 802.11 frames from
wireless clients inside LWAPP frames and forward
the LWAPP frames to the controller.
GLOSSARY
Access Point ( AP )
An entity that contains an 802.11 medium access
control ( MAC ) and physical layer ( PHY ) interface
and provides access to the distribution services via
the wireless medium for associated clients.
LWAPP APs encapsulate all the 802.11 frames in
LWAPP frames and sends it to the controller to which
it is logically connected to.
Central Controller ( CC )
The central entity that terminates the LWAPP protocol
tunnel from the LWAPP APs. Throughout this MIB,
this entity also referred to as 'controller'.
Light Weight Access Point Protocol ( LWAPP )
This is a generic protocol that defines the
communication between the Access Points and the
controllers.
Mobile Node ( MN )
A roaming 802.11 wireless device in a wireless
network associated with an access point.
802.1x
The IEEE ratified standard for enforcing port based
access control. This was originally intended for
use on wired LANs and later extended for use in
802.11 WLAN environments. This defines an
architecture with three main parts - a supplicant
(Ex. an 802.11 wireless client), an authenticator
(the AP) and an authentication server(a Radius
server). The authenticator passes messages back
and forth between the supplicant and the
authentication server to enable the supplicant
get authenticated to the network.
Radio Frequency ( RF )
Radio frequency (RF) is a rate of oscillation in the
range of about 3 kHz to 300 GHz, which corresponds to
the frequency of radio waves, and the
alternating currents which carry radio signals.
Received Signal Strength Indicator ( RSSI )
A measure of the strength of the signal as
observed by the entity that received it,
expressed in 'dbm'.
Coverage Hole Detection ( CHD )
If clients on an Access Point are detected at low
RSSI levels, it is considered a coverage hole
by the Access Points. This indicates the existence
of an area where clients are continually getting poor
signal coverage, without having a viable location to
roam to.
REFERENCE
[1] Wireless LAN Medium Access Control ( MAC ) and
Physical Layer ( PHY ) Specifications.
[2] Draft-obara-capwap-lwapp-00.txt, IETF Light
Weight Access Point Protocol
[3] IEEE 802.11 - The original 1 Mbit/s and 2 Mbit/s,
2.4 GHz RF and IR standard. | |||||||||||||||||||||
| NciscoLwappRFMIBNotifs | 1.3.6.1.4.1.9.9.778.0 | ||||||||||||||||||||
| NciscoLwappRFMIBObjects | 1.3.6.1.4.1.9.9.778.1 | ||||||||||||||||||||
| NciscoLwappRFConfig | 1.3.6.1.4.1.9.9.778.1.1 | ||||||||||||||||||||
| TcLAPGroupsRFProfileTable | 1.3.6.1.4.1.9.9.778.1.1.1 | NA | |||||||||||||||||||
table · not-accessible · current This table lists the mapping between an RF profile and an AP group. | |||||||||||||||||||||
| RcLAPGroupsRFProfileEntry | 1.3.6.1.4.1.9.9.778.1.1.1.1 | NA | |||||||||||||||||||
row · not-accessible · current An entry containing the configuration attributes that affect the operation of the APs within a group. Entries can be added/deleted by explicit management action from NMS/EMS through the 'bsnAPGroupsVlanRowStatus' object in bsnAPGroupsVlanTable as defined by the AIRESPACE-WIRELESS-MIB.
| |||||||||||||||||||||
| CcLAPGroups802dot11bgRFProfileName | 1.3.6.1.4.1.9.9.778.1.1.1.1.1 | SnmpAdminString (SIZE (0..64)) | RW | ||||||||||||||||||
column · SnmpAdminString (SIZE (0..64)) · read-write · current This object specifies the RF profile name assigned to this site on the 802.11bg radio. This profile being assigned should exist in the 'cLRFProfileTable'. To disassociate a profile with this site a string of zero length should be set. | |||||||||||||||||||||
| CcLAPGroups802dot11aRFProfileName | 1.3.6.1.4.1.9.9.778.1.1.1.1.2 | SnmpAdminString (SIZE (0..64)) | RW | ||||||||||||||||||
column · SnmpAdminString (SIZE (0..64)) · read-write · current This object specifies the RF profile name assigned to this site on the 802.11a radio. This profile being assigned should exist in the 'cLRFProfileTable'. To disassociate a profile with this site a string of zero length should be set. | |||||||||||||||||||||
| TcLRFProfileTable | 1.3.6.1.4.1.9.9.778.1.1.2 | NA | |||||||||||||||||||
table · not-accessible · current This table lists the configuration for each RF profile. | |||||||||||||||||||||
| RcLRFProfileEntry | 1.3.6.1.4.1.9.9.778.1.1.2.1 | NA | |||||||||||||||||||
row · not-accessible · current An entry containing the configuration attributes that affect the operation of 802.11 RF domain. Entries can be added/deleted by explicit management action from NMS/EMS or through user console.
| |||||||||||||||||||||
| CcLRFProfileName | 1.3.6.1.4.1.9.9.778.1.1.2.1.1 | SnmpAdminString (SIZE (1..64)) | NA | ||||||||||||||||||
column · SnmpAdminString (SIZE (1..64)) · not-accessible · current This object uniquely identifies a RF Profile. | |||||||||||||||||||||
| CcLRFProfileDescr | 1.3.6.1.4.1.9.9.778.1.1.2.1.2 | SnmpAdminString (SIZE (0..64)) | RC | default rfprofile for 6GHz radio | |||||||||||||||||
column · SnmpAdminString (SIZE (0..64)) · read-create · current This object specifies a human-readable description of the profile. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLRFProfileTransmitPowerMin | 1.3.6.1.4.1.9.9.778.1.1.2.1.3 | Integer32 (-10..30) | RC | -10 | |||||||||||||||||
column · Integer32 (-10..30) · read-create · current This object specifies the lower bound of transmit power value supported by an AP.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLRFProfileTransmitPowerMax | 1.3.6.1.4.1.9.9.778.1.1.2.1.4 | Integer32 (-10..30) | RC | 30 | |||||||||||||||||
column · Integer32 (-10..30) · read-create · current This object specifies the uppoer bound of transmit power value supported by an AP.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLRFProfileTransmitPowerThresholdV1 | 1.3.6.1.4.1.9.9.778.1.1.2.1.5 | Integer32 (-80..-50) | RC | -70 | |||||||||||||||||
column · Integer32 (-80..-50) · read-create · current This object specifies the transmit power control version 1 threshold for the radio resource management algorithm.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLRFProfileTransmitPowerThresholdV2 | 1.3.6.1.4.1.9.9.778.1.1.2.1.6 | Integer32 (-80..-50) | RC | -67 | |||||||||||||||||
column · Integer32 (-80..-50) · read-create · current This object specifies the transmit power control version 2 threshold for the radio resource management algorithm.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLRFProfileDataRate1Mbps | 1.3.6.1.4.1.9.9.778.1.1.2.1.7 | CiscoLwappRFApDataRates | RC | 2 | |||||||||||||||||
column · CiscoLwappRFApDataRates · read-create · current This object specifies the configuration for this data rate. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLRFProfileDataRate2Mbps | 1.3.6.1.4.1.9.9.778.1.1.2.1.8 | CiscoLwappRFApDataRates | RC | 2 | |||||||||||||||||
column · CiscoLwappRFApDataRates · read-create · current This object specifies the configuration for this data rate. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLRFProfileDataRate5AndHalfMbps | 1.3.6.1.4.1.9.9.778.1.1.2.1.9 | CiscoLwappRFApDataRates | RC | 2 | |||||||||||||||||
column · CiscoLwappRFApDataRates · read-create · current This object specifies the configuration for this data rate. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLRFProfileDataRate11Mbps | 1.3.6.1.4.1.9.9.778.1.1.2.1.10 | CiscoLwappRFApDataRates | RC | 2 | |||||||||||||||||
column · CiscoLwappRFApDataRates · read-create · current This object specifies the configuration for this data rate. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLRFProfileDataRate6Mbps | 1.3.6.1.4.1.9.9.778.1.1.2.1.11 | CiscoLwappRFApDataRates | RC | 0 | |||||||||||||||||
column · CiscoLwappRFApDataRates · read-create · current This object specifies the configuration for this data rate. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLRFProfileDataRate9Mbps | 1.3.6.1.4.1.9.9.778.1.1.2.1.12 | CiscoLwappRFApDataRates | RC | 0 | |||||||||||||||||
column · CiscoLwappRFApDataRates · read-create · current This object specifies the configuration for this data rate. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLRFProfileDataRate12Mbps | 1.3.6.1.4.1.9.9.778.1.1.2.1.13 | CiscoLwappRFApDataRates | RC | 2 | |||||||||||||||||
column · CiscoLwappRFApDataRates · read-create · current This object specifies the configuration for this data rate. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLRFProfileDataRate18Mbps | 1.3.6.1.4.1.9.9.778.1.1.2.1.14 | CiscoLwappRFApDataRates | RC | 1 | |||||||||||||||||
column · CiscoLwappRFApDataRates · read-create · current This object specifies the configuration for this data rate. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLRFProfileDataRate24Mbps | 1.3.6.1.4.1.9.9.778.1.1.2.1.15 | CiscoLwappRFApDataRates | RC | 2 | |||||||||||||||||
column · CiscoLwappRFApDataRates · read-create · current This object specifies the configuration for this data rate. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLRFProfileDataRate36Mbps | 1.3.6.1.4.1.9.9.778.1.1.2.1.16 | CiscoLwappRFApDataRates | RC | 1 | |||||||||||||||||
column · CiscoLwappRFApDataRates · read-create · current This object specifies the configuration for this data rate. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLRFProfileDataRate48Mbps | 1.3.6.1.4.1.9.9.778.1.1.2.1.17 | CiscoLwappRFApDataRates | RC | 1 | |||||||||||||||||
column · CiscoLwappRFApDataRates · read-create · current This object specifies the configuration for this data rate. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLRFProfileDataRate54Mbps | 1.3.6.1.4.1.9.9.778.1.1.2.1.18 | CiscoLwappRFApDataRates | RC | 1 | |||||||||||||||||
column · CiscoLwappRFApDataRates · read-create · current This object specifies the configuration for this data rate. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLRFProfileRadioType | 1.3.6.1.4.1.9.9.778.1.1.2.1.19 | CLApIfType | RC | 3 | |||||||||||||||||
column · CLApIfType · read-create · current This object is used to configure the radio type for this profile. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLRFProfileStorageType | 1.3.6.1.4.1.9.9.778.1.1.2.1.20 | StorageType | RC | 3 | |||||||||||||||||
column · StorageType · read-create · current This object represents the storage type for this conceptual row. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLRFProfileRowStatus | 1.3.6.1.4.1.9.9.778.1.1.2.1.21 | RowStatus | RC | 1 | |||||||||||||||||
column · RowStatus · read-create · current This is the status column for this row and used to create and delete specific instances of rows in this table. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLRFProfileHighDensityMaxRadioClients | 1.3.6.1.4.1.9.9.778.1.1.2.1.22 | Unsigned32 | RC | 200 | |||||||||||||||||
column · Unsigned32 · read-create · current This object specifies the maximum number of clients per AP radio in high density environment. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLRFProfileBandSelectProbeResponse | 1.3.6.1.4.1.9.9.778.1.1.2.1.23 | TruthValue | RC | 2 | |||||||||||||||||
column · TruthValue · read-create · current This object specifies the AP's probe response with clients to verify whether client can associate on both 2.4 GHz and 5Ghz spectrum. When set to true, AP suppresses probe response to new clients for all SSIDs that are not being Band Select disabled. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLRFProfileBandSelectCycleCount | 1.3.6.1.4.1.9.9.778.1.1.2.1.24 | Unsigned32 | RC | 2 | |||||||||||||||||
column · Unsigned32 · read-create · current This object specifies number of times a client probe (2.4 G-Hz) is suppressed before the AP starts responding to the probes. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLRFProfileBandSelectCycleThreshold | 1.3.6.1.4.1.9.9.778.1.1.2.1.25 | Unsigned32 | RC | 200 | |||||||||||||||||
column · Unsigned32 · read-create · current This object specifies time threshold for a new scanning mobile station period. Mobile station cycle counter will increment only if mobile station scans same channel any time after threshold is passed.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLRFProfileBandSelectExpireSuppression | 1.3.6.1.4.1.9.9.778.1.1.2.1.26 | Unsigned32 | RC | 20 | |||||||||||||||||
column · Unsigned32 · read-create · current This object specifies the duration at which an AP waits to conduct another probe suppression.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLRFProfileBandSelectExpireDualBand | 1.3.6.1.4.1.9.9.778.1.1.2.1.27 | Unsigned32 | RC | 60 | |||||||||||||||||
column · Unsigned32 · read-create · current This object specifies the timeout duration until which an AP should not respond to 2.4ghz probe requests from a dual-band client. Once this band select duration expires the client will be marked as a non-dual band client and AP will start responding to the 2.4 Ghz probes.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLRFProfileBandSelectClientRSSI | 1.3.6.1.4.1.9.9.778.1.1.2.1.28 | Integer32 | RC | -80 | |||||||||||||||||
column · Integer32 · read-create · current This object specifies minimum mobile station RSSI threshold. Mobile stations having RSSI below this value will not be recorded in the suppressed table. This configuration filters out far away mobile stations with weaker signal strength. This will limit the number of mobile stations on the table to a reasonable amount.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLRFProfileLoadBalancingWindowSize | 1.3.6.1.4.1.9.9.778.1.1.2.1.29 | Unsigned32 | RC | 5 | |||||||||||||||||
column · Unsigned32 · read-create · current This object specifies the minimum number of clients to be associated on an AP in order to trigger load balancing. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLRFProfileLoadBalancingMaxDenialCount | 1.3.6.1.4.1.9.9.778.1.1.2.1.30 | Unsigned32 | RC | 3 | |||||||||||||||||
column · Unsigned32 · read-create · current This object specifies maximum number of association rejections sent by AP to a mobile station for a given sequence of association. When a mobile station tries to associate on wireless network, it sends association request to AP. If AP is overloaded and load balancing is enable on controller, AP will send a denial to association request. If there are no other AP in the vicinity of mobile station, it will try to associate same AP again. So to restrict the number of denial sent from AP, cldLoadBalancingMaxDenialCount is defined. After maximum denial count is reached mobile station will be able to associate. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLRFProfileCHDDataRSSIThreshold | 1.3.6.1.4.1.9.9.778.1.1.2.1.31 | Integer32 | RC | -80 | |||||||||||||||||
column · Integer32 · read-create · current This object specifies the RSSI value for non-voice clients i.e., clients sending only data traffic to trigger coverage event.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLRFProfileCHDVoiceRSSIThreshold | 1.3.6.1.4.1.9.9.778.1.1.2.1.32 | Integer32 | RC | -80 | |||||||||||||||||
column · Integer32 · read-create · current This object specifies the RSSI value for voice clients to trigger coverage event.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLRFProfileCHDClientExceptionLevel | 1.3.6.1.4.1.9.9.778.1.1.2.1.33 | Unsigned32 | RC | 3 | |||||||||||||||||
column · Unsigned32 · read-create · current This object specifies the minimum number of clients required to trigger coverage hole. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLRFProfileCHDCoverageExceptionLevel | 1.3.6.1.4.1.9.9.778.1.1.2.1.34 | Unsigned32 | RC | 25 | |||||||||||||||||
column · Unsigned32 · read-create · current This object specifies the minimum percentage of clients in the coverage hole region of the AP, required to trigger a coverage hole exception
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLRFProfileMulticastDataRate | 1.3.6.1.4.1.9.9.778.1.1.2.1.35 | Unsigned32 | RC | 0 | |||||||||||||||||
column · Unsigned32 · read-create · current This object specifies the minimum data rate at which multicast clients can associate to AP. A value 0 indicates that AP will automatically adjust data rates.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLRFProfile11nOnly | 1.3.6.1.4.1.9.9.778.1.1.2.1.36 | TruthValue | RC | 2 | |||||||||||||||||
column · TruthValue · read-create · current This object specifies if 11n-client-only mode is enabled. A value of 'true' indicates 11n-client-only mode enabled. A value of 'false' indicates 11n-client-only mode disabled. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLRFProfileHDClientTrapThreshold | 1.3.6.1.4.1.9.9.778.1.1.2.1.37 | Unsigned32 | RC | 12 | |||||||||||||||||
column · Unsigned32 · read-create · current This object specifies the threshold number of clients per AP radio to trigger a trap. The trap ciscoLwappApClientThresholdNotify will be triggered once the count of clients on the AP radio reaches this limit. A value of zero indicates that the trap is disabled. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLRFProfileInterferenceThreshold | 1.3.6.1.4.1.9.9.778.1.1.2.1.38 | Unsigned32 (0..100) | RC | 10 | |||||||||||||||||
column · Unsigned32 (0..100) · read-create · current This object specifies interference threshold in % traps are generated when interference exceeds this value .
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLRFProfileNoiseThreshold | 1.3.6.1.4.1.9.9.778.1.1.2.1.39 | Integer32 (-127..0) | RC | -70 | |||||||||||||||||
column · Integer32 (-127..0) · read-create · current This object specifies the threshold number of noise threshold between -127 and 0 dBm.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLRFProfileUtilizationThreshold | 1.3.6.1.4.1.9.9.778.1.1.2.1.40 | Unsigned32 (0..100) | RC | 80 | |||||||||||||||||
column · Unsigned32 (0..100) · read-create · current This object specifies the threshold of bandwidth (%) being utilized by an access-point. Traps are sent when this value is exceeded
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLRFProfileDCAForeignContribution | 1.3.6.1.4.1.9.9.778.1.1.2.1.41 | TruthValue | RC | 1 | |||||||||||||||||
column · TruthValue · read-create · current This object specifies whether foreign interference is taken into account for the DCA metrics. A value of 'true' indicates that foreign interference is is considered when DCA metrics is derived. A value of 'false' indicates foreign interference is not taken into account when deriving the DCA metrics. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLRFProfileDCAChannelWidth | 1.3.6.1.4.1.9.9.778.1.1.2.1.42 | INTEGER | RC | best(5) | |||||||||||||||||
column · INTEGER · read-create · current This object specifies how the system performs DCA
channel width selection for the RFProfile
twenty - 20MHz channel width supported by
this radio.
forty - 40MHz channel width supported by this radio.
eighty - 80MHz channel width supported by this radio.
onesixty - 160MHz channel width supported by this radio.
best - Dynamic channel width(160MHz, 80MHz, 40MHz
or 20MHz) supported by this radio.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLRFProfileDCAChannelList | 1.3.6.1.4.1.9.9.778.1.1.2.1.43 | SnmpAdminString (SIZE (1..500)) | RC | | |||||||||||||||||
column · SnmpAdminString (SIZE (1..500)) · read-create · current This object specifies the 802.11 channels available to the RF Profile. A comma separated list of integers. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLRFProfileRxSopThreshold | 1.3.6.1.4.1.9.9.778.1.1.2.1.44 | INTEGER | RC | auto(0) | |||||||||||||||||
column · INTEGER · read-create · current This object specifies the receiver start of packet threshold for the rf profile. auto - Reverts radio receiver SOP to auto. high - Sets radio receiver SOP to high. low - Sets radio receiver SOP to low. medium - Sets radio receiver SOP to medium. custom - Sets radio receiver SOP to Custom value.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLRFProfileHSRMode | 1.3.6.1.4.1.9.9.778.1.1.2.1.45 | TruthValue | RC | 2 | |||||||||||||||||
column · TruthValue · read-create · current This object specifies whether HSR mode for RF profile is enabled or not. A value of 'true' indicates that HSR is enabled. A value of 'false' indicates that HSR is disabled. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLRFProfileHSRNeighborTimeoutFactor | 1.3.6.1.4.1.9.9.778.1.1.2.1.46 | Unsigned32 | RC | 5 | |||||||||||||||||
column · Unsigned32 · read-create · current This object specifies the timeout interval of neighbors that will be configured for RF profile. Neighbor timeout factor will be five times the neighbor interval
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLRFProfileBandSelectClientMidRSSI | 1.3.6.1.4.1.9.9.778.1.1.2.1.47 | Integer32 | RC | -80 | |||||||||||||||||
column · Integer32 · read-create · current This object specifies medium mobile station RSSI threshold. Mobile station between this value and cldBandSelectClientRssi will be recorded in suppressed table but will not be denied. The mobile station having RSSI stronger than this value will be recorded and denied.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLRFProfileClientNetworkPreference | 1.3.6.1.4.1.9.9.778.1.1.2.1.48 | INTEGER | RC | throughput(2) | |||||||||||||||||
column · INTEGER · read-create · current This object represents the client network preference.
default(0) - RRM Algorithm has no preference on
the clients.
connectivity(1) - RRM Algorithm has a preference on
connectiviry of the clients.
throughput(2) - RRM Algorithm has a preference on
high thoughput of the clients.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLRFProfileUnusedChannelList | 1.3.6.1.4.1.9.9.778.1.1.2.1.49 | SnmpAdminString (SIZE (1..500)) | RO | | |||||||||||||||||
column · SnmpAdminString (SIZE (1..500)) · read-only · current This object specifies the 802.11 channels present in ths un-used channel list of RF Profile. A comma separated list of integers. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLRFProfileShutdown | 1.3.6.1.4.1.9.9.778.1.1.2.1.50 | TruthValue | RW | 1 | |||||||||||||||||
column · TruthValue · read-write · current This object specifies if rf profile is disabled. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLRFProfileAirTimeFairnessMode | 1.3.6.1.4.1.9.9.778.1.1.2.1.51 | INTEGER | RW | disable(1) | |||||||||||||||||
column · INTEGER · read-write · current This object specifies the mode of fairness for ATF
supported APs, joined to the controller.
disable(1) - This indicates that fairness mode is
disabled.
SSID Mode(2) - This indicates that fairness mode is SSID
mode.
Monitor Mode(3) - This indicates that fairness mode is
monitor mode.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLRFProfileAirTimeFairnessOptimization | 1.3.6.1.4.1.9.9.778.1.1.2.1.52 | INTEGER | RW | disable(1) | |||||||||||||||||
column · INTEGER · read-write · current This object specifies the optimization for ATF supported APs, joined to the controller to be configured.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLRFProfileBridgeClientAccess | 1.3.6.1.4.1.9.9.778.1.1.2.1.53 | TruthValue | RW | 2 | |||||||||||||||||
column · TruthValue · read-write · current This object specifies whether airtime allocation is enabled for the client access node. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLRFProfileAirTimeAllocation | 1.3.6.1.4.1.9.9.778.1.1.2.1.54 | Unsigned32 (5..90) | RW | 5 | |||||||||||||||||
column · Unsigned32 (5..90) · read-write · current This object specifies the percentage for airtime allocation for the client access node. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLRFProfileRxSopThresholdCustom | 1.3.6.1.4.1.9.9.778.1.1.2.1.55 | Integer32 (-85..-60) | RW | -85 | |||||||||||||||||
column · Integer32 (-85..-60) · read-write · current This object specifies the percentage for the receiver start of packet custom threshold for the client access node. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLRFProfile11axObssPdEnable | 1.3.6.1.4.1.9.9.778.1.1.2.1.56 | TruthValue | RW | 2 | |||||||||||||||||
column · TruthValue · read-write · current This object specifies whether 802.11ax OBSS PD spatial reuse is enabled for the RF profile. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLRFProfile11axNonSrgObssPdMax | 1.3.6.1.4.1.9.9.778.1.1.2.1.57 | Integer32 (-82..-62) | RW | -62 | |||||||||||||||||
column · Integer32 (-82..-62) · read-write · current This object specifies the non-SRG OBSS PD max threshold in dBm for the RF profile. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLRFProfileNdpMode | 1.3.6.1.4.1.9.9.778.1.1.2.1.58 | INTEGER | RC | auto(0) | |||||||||||||||||
column · INTEGER · read-create · current This object specifies the neighbor discovery mode of AP for this RF profile auto - neighbor discovery mode is auto. offChannel - neighbor discovery mode is off-channel.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLRFProfile11ax6GHzFeature | 1.3.6.1.4.1.9.9.778.1.1.2.1.59 | INTEGER | RW | none(0) | |||||||||||||||||
column · INTEGER · read-write · current This object specifies whether 802.11ax UBPR or FILS discovery enabled for the RF profile.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLRFProfile11axBcastProbeRespInterval | 1.3.6.1.4.1.9.9.778.1.1.2.1.60 | Unsigned32 (5..25) | RW | 20 | |||||||||||||||||
column · Unsigned32 (5..25) · read-write · current This object specifies the 802.11ax Broadcast Probe response interval in msec.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLRFProfileMultiBssidProfile | 1.3.6.1.4.1.9.9.778.1.1.2.1.62 | SnmpAdminString (SIZE (0..64)) | RW | default-multi-bssid-profile | |||||||||||||||||
column · SnmpAdminString (SIZE (0..64)) · read-write · current This object specifies the Multi-BSSID profile name that is mapped to the RF profile. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLRFProfilePSCBias | 1.3.6.1.4.1.9.9.778.1.1.2.1.63 | TruthValue | RW | 2 | |||||||||||||||||
column · TruthValue · read-write · current This object specifies whether preferred scanning channel bias for 6 GHz DCA is enabled or disabled for the RF profile. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLRFProfile11axSrgObssPdEnable | 1.3.6.1.4.1.9.9.778.1.1.2.1.64 | TruthValue | RW | 2 | |||||||||||||||||
column · TruthValue · read-write · current This object specifies whether 802.11ax SRG OBSS PD spatial reuse is enabled for the RF profile. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLRFProfile11axSrgObssPdMin | 1.3.6.1.4.1.9.9.778.1.1.2.1.65 | Integer32 (-82..-62) | RW | -82 | |||||||||||||||||
column · Integer32 (-82..-62) · read-write · current This object specifies the SRG OBSS PD min threshold in dBm for the RF profile. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLRFProfile11axSrgObssPdMax | 1.3.6.1.4.1.9.9.778.1.1.2.1.66 | Integer32 (-82..-62) | RW | -62 | |||||||||||||||||
column · Integer32 (-82..-62) · read-write · current This object specifies the SRG OBSS PD max threshold in dBm for the RF profile. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLRFProfilePreamblePuncture | 1.3.6.1.4.1.9.9.778.1.1.2.1.67 | TruthValue | RW | ||||||||||||||||||
column · TruthValue · read-write · current This object specifies whether Preamble puncturing is enabled for the RF profile. | |||||||||||||||||||||
| TcLRFProfileMcsDataRateTable | 1.3.6.1.4.1.9.9.778.1.1.3 | NA | |||||||||||||||||||
table · not-accessible · current This object specifies the 11n MCS rates supported by the RF profile, indexed by the MCS rate, ranging from 1 to 32, corresponding to rate MCS-0, MCS-1, ... MCS-31. | |||||||||||||||||||||
| RcLRFProfileMcsDataRateEntry | 1.3.6.1.4.1.9.9.778.1.1.3.1 | NA | |||||||||||||||||||
row · not-accessible · current An entry containing MCS date rate information applicable to a particular profile. Entry is added to the table when the data rate is set to 'supported' or 'mandatory'. | |||||||||||||||||||||
| CcLRFProfileMcsName | 1.3.6.1.4.1.9.9.778.1.1.3.1.1 | SnmpAdminString (SIZE (1..64)) | NA | ||||||||||||||||||
column · SnmpAdminString (SIZE (1..64)) · not-accessible · current This object uniquely identifies a RF Profile. | |||||||||||||||||||||
| CcLRFProfileMcsRate | 1.3.6.1.4.1.9.9.778.1.1.3.1.2 | Unsigned32 | NA | ||||||||||||||||||
column · Unsigned32 · not-accessible · current This object uniquely identifies the MCS data rate for a particular profile. | |||||||||||||||||||||
| CcLRFProfileMcsRateSupport | 1.3.6.1.4.1.9.9.778.1.1.3.1.3 | TruthValue | RW | 1 | |||||||||||||||||
column · TruthValue · read-write · current This object is used to enable or disable the data rate. A value of 'true' indicates MCS support is enabled. A value of 'false' indicates MCS support is disabled. Example values from LibreNMS test devices
| |||||||||||||||||||||
| TcLRFProfileChannelListTable | 1.3.6.1.4.1.9.9.778.1.1.4 | NA | |||||||||||||||||||
table · not-accessible · current This object specifies the list of channels that is available for DCA of a RF profile. | |||||||||||||||||||||
| RcLRFProfileChannelListEntry | 1.3.6.1.4.1.9.9.778.1.1.4.1 | NA | |||||||||||||||||||
row · not-accessible · current An entry containing Channel List information applicable to a particular profile. | |||||||||||||||||||||
| CcLRFProfileChanNumber | 1.3.6.1.4.1.9.9.778.1.1.4.1.1 | Unsigned32 | NA | ||||||||||||||||||
column · Unsigned32 · not-accessible · current This object uniquely identifies the channel for a particular profile. | |||||||||||||||||||||
| CcLRFProfileChanAddRemove | 1.3.6.1.4.1.9.9.778.1.1.4.1.2 | INTEGER | RC | ||||||||||||||||||
column · INTEGER · read-create · current This object specifies a channel is to be added or removed from DCA list of the RFProfile. add - Add the channel to global DCA channel list. remove - Removed the channel from global DCA channel list.
| |||||||||||||||||||||
| CcLRFProfileChanRowStatus | 1.3.6.1.4.1.9.9.778.1.1.4.1.3 | RowStatus | RC | ||||||||||||||||||
column · RowStatus · read-create · current This is the status column for this row and used to create and delete specific instances of rows in this table. | |||||||||||||||||||||
| TcLRFProfileRemoveChannelTable | 1.3.6.1.4.1.9.9.778.1.1.5 | NA | |||||||||||||||||||
table · not-accessible · current This table represents the removed channel information from default DCA channel list for an AP's 802.11 interface using the RF profile. Based on the country that an AP operates in, it gets assigned to a regulatory domain. For a given regulatory domain a fixed number of channels are assigned automatically to an AP for a given interface. We can remove a channel from this default list and those channels will be put in this table. This table represents the removed DCA channels information. By default, there will not be any entries in this table. An entry can be created or deleted from this table using cLRFProfileRemoveChannelRowStatus. | |||||||||||||||||||||
| RcLRFProfileRemoveChannelEntry | 1.3.6.1.4.1.9.9.778.1.1.5.1 | NA | |||||||||||||||||||
row · not-accessible · current Each entry in this table provides the removed channel information from the default DCA channel list for this RF profile | |||||||||||||||||||||
| CcLRFProfileRemoveChannelName | 1.3.6.1.4.1.9.9.778.1.1.5.1.1 | SnmpAdminString (SIZE (1..64)) | NA | ||||||||||||||||||
column · SnmpAdminString (SIZE (1..64)) · not-accessible · current This object uniquely identifies a RF Profile. | |||||||||||||||||||||
| CcLRFProfileRemoveChannelNum | 1.3.6.1.4.1.9.9.778.1.1.5.1.2 | Unsigned32 | NA | ||||||||||||||||||
column · Unsigned32 · not-accessible · current The channel nubmer for this entry. This value represents the unique channel number removed from default DCA channel list for this RF profile. | |||||||||||||||||||||
| CcLRFProfileRemovedChannelDcaState | 1.3.6.1.4.1.9.9.778.1.1.5.1.3 | TruthValue | RC | ||||||||||||||||||
column · TruthValue · read-create · current This object specifies whether this channel is part of the dynamic channel allocation (DCA) Remove List. A value of 'false' indicates that the DCA for this channel is disabled. | |||||||||||||||||||||
| CcLRFProfileRemoveChannelRowStatus | 1.3.6.1.4.1.9.9.778.1.1.5.1.4 | RowStatus | RC | ||||||||||||||||||
column · RowStatus · read-create · current The status of this conceptual row. All writable objects in this row may be modified at any time. | |||||||||||||||||||||
| TcLRFProfileAddChannelTable | 1.3.6.1.4.1.9.9.778.1.1.6 | NA | |||||||||||||||||||
table · not-accessible · current This table represents the added channel information to the default DCA channel list in this RF profile. Based on the country that an AP operates in, it gets assigned to a regulatory domain. For a given regulatory domain a fixed number of channels are assigned automatically to an AP for a given interface. We can add a channel to this default list and those channels will be put in this table. This table represents the added channels information to the default DCA channel list. By default, there will not be any entries in this table. An entry can be created or deleted from this table using cLRFProfileAddChannelRowStatus. | |||||||||||||||||||||
| RcLRFProfileAddChannelEntry | 1.3.6.1.4.1.9.9.778.1.1.6.1 | NA | |||||||||||||||||||
row · not-accessible · current Each entry in this table provides the added channel information to the default DCA channel list in this RF profile. | |||||||||||||||||||||
| CcLRFProfileAddChannelName | 1.3.6.1.4.1.9.9.778.1.1.6.1.1 | SnmpAdminString (SIZE (1..64)) | NA | ||||||||||||||||||
column · SnmpAdminString (SIZE (1..64)) · not-accessible · current This object uniquely identifies a RF Profile. | |||||||||||||||||||||
| CcLRFProfileAddChannelNum | 1.3.6.1.4.1.9.9.778.1.1.6.1.2 | Unsigned32 | NA | ||||||||||||||||||
column · Unsigned32 · not-accessible · current The channel nubmer for this entry. This value represents the unique channel number added to the default DCA list in this RF profile. | |||||||||||||||||||||
| CcLRFProfileAddedChannelDcaState | 1.3.6.1.4.1.9.9.778.1.1.6.1.3 | TruthValue | RC | ||||||||||||||||||
column · TruthValue · read-create · current This object specifies whether this channel is part of the dynamic channel allocation (DCA) Add List. A value of 'true' indicates that the DCA for this channel is enabled. | |||||||||||||||||||||
| CcLRFProfileAddChannelRowStatus | 1.3.6.1.4.1.9.9.778.1.1.6.1.4 | RowStatus | RC | ||||||||||||||||||
column · RowStatus · read-create · current The status of this conceptual row. All writable objects in this row may be modified at any time. | |||||||||||||||||||||
| TcLMultiBSSIDProfileTable | 1.3.6.1.4.1.9.9.778.1.1.7 | NA | |||||||||||||||||||
table · not-accessible · current This table represents the configuration related to each Multi BSSID profile. | |||||||||||||||||||||
| RcLMultiBSSIDProfileEntry | 1.3.6.1.4.1.9.9.778.1.1.7.1 | NA | |||||||||||||||||||
row · not-accessible · current Each entry in this table stores the configurations related to a Multi BSSID Profile. Entries can be added/deleted by explicit management action from NMS/EMS or through user console. | |||||||||||||||||||||
| CcLMultiBSSIDProfileName | 1.3.6.1.4.1.9.9.778.1.1.7.1.1 | SnmpAdminString (SIZE (1..64)) | NA | ||||||||||||||||||
column · SnmpAdminString (SIZE (1..64)) · not-accessible · current This object uniquely identifies a Multi BSSID Profile. | |||||||||||||||||||||
| CcLMultiBSSIDProfileDescr | 1.3.6.1.4.1.9.9.778.1.1.7.1.2 | SnmpAdminString (SIZE (0..64)) | RC | Default multi bssid profile | |||||||||||||||||
column · SnmpAdminString (SIZE (0..64)) · read-create · current This object specifies a human-readable description of the Multi BSSID profile. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLMultiBSSIDProfile11axOfdmaDownLink | 1.3.6.1.4.1.9.9.778.1.1.7.1.3 | TruthValue | RC | 1 | |||||||||||||||||
column · TruthValue · read-create · current This object specifies if 802.11ax OFDMA Downlink is enabled. A value of 'true' indicates 802.11ax OFDMA Downlink enabled. A value of 'false' indicates 802.11ax OFDMA Downlink disabled. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLMultiBSSIDProfile11axOfdmaUpLink | 1.3.6.1.4.1.9.9.778.1.1.7.1.4 | TruthValue | RC | 1 | |||||||||||||||||
column · TruthValue · read-create · current This object specifies if 802.11ax OFDMA Uplink is enabled. A value of 'true' indicates 802.11ax OFDMA Uplink enabled. A value of 'false' indicates 802.11ax OFDMA Uplink disabled. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLMultiBSSIDProfile11axMuMIMODownLink | 1.3.6.1.4.1.9.9.778.1.1.7.1.5 | TruthValue | RC | 1 | |||||||||||||||||
column · TruthValue · read-create · current This object specifies if 802.11ax MU-MIMO Downlink is enabled. A value of 'true' indicates 802.11ax MU-MIMO Downlink enabled. A value of 'false' indicates 802.11ax MU-MIMO Downlink disabled. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLMultiBSSIDProfile11axMuMIMOUpLink | 1.3.6.1.4.1.9.9.778.1.1.7.1.6 | TruthValue | RC | 1 | |||||||||||||||||
column · TruthValue · read-create · current This object specifies if 802.11ax MU-MIMO Uplink is enabled. A value of 'true' indicates 802.11ax MU-MIMO Uplink enabled. A value of 'false' indicates 802.11ax MU-MIMO Uplink disabled. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLMultiBSSIDProfile11axTwt | 1.3.6.1.4.1.9.9.778.1.1.7.1.7 | TruthValue | RC | 2 | |||||||||||||||||
column · TruthValue · read-create · current This object specifies if 802.11ax Target Wakeup Time(TWT) is enabled. A value of 'true' indicates that 802.11ax TWT is enabled. enabled. A value of 'false' indicates that 802.11ax TWT is disabled. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLMultiBSSIDProfile11axTwtBroadcast | 1.3.6.1.4.1.9.9.778.1.1.7.1.8 | TruthValue | RC | 2 | |||||||||||||||||
column · TruthValue · read-create · current This object specifies if 802.11ax Target Wakeup Time(TWT) Broadcast is enabled. A value of 'true' indicates 802.11ax TWT Broadcast enabled. A value of 'false' indicates 802.11ax TWT Broadcast disabled. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLMultiBSSIDProfileRowStatus | 1.3.6.1.4.1.9.9.778.1.1.7.1.9 | RowStatus | RC | 1 | |||||||||||||||||
column · RowStatus · read-create · current This is the status column for this row and used to create and delete specific instances of rows in this table. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcLMultiBSSIDProfile11beOfdmaDownLink | 1.3.6.1.4.1.9.9.778.1.1.7.1.10 | TruthValue | RC | ||||||||||||||||||
column · TruthValue · read-create · current This object specifies if 802.11be OFDMA Downlink is enabled. A value of 'true' indicates 802.11be OFDMA Downlink enabled. A value of 'false' indicates 802.11be OFDMA Downlink disabled. | |||||||||||||||||||||
| CcLMultiBSSIDProfile11beOfdmaUpLink | 1.3.6.1.4.1.9.9.778.1.1.7.1.11 | TruthValue | RC | ||||||||||||||||||
column · TruthValue · read-create · current This object specifies if 802.11be OFDMA Uplink is enabled. A value of 'true' indicates 802.11be OFDMA Uplink enabled. A value of 'false' indicates 802.11be OFDMA Uplink disabled. | |||||||||||||||||||||
| CcLMultiBSSIDProfile11beMuMIMODownLink | 1.3.6.1.4.1.9.9.778.1.1.7.1.12 | TruthValue | RC | ||||||||||||||||||
column · TruthValue · read-create · current This object specifies if 802.11be MU-MIMO Downlink is enabled. A value of 'true' indicates 802.11be MU-MIMO Downlink enabled. A value of 'false' indicates 802.11be MU-MIMO Downlink disabled. | |||||||||||||||||||||
| CcLMultiBSSIDProfile11beMuMIMOUpLink | 1.3.6.1.4.1.9.9.778.1.1.7.1.13 | TruthValue | RC | ||||||||||||||||||
column · TruthValue · read-create · current This object specifies if 802.11be MU-MIMO Uplink is enabled. A value of 'true' indicates 802.11be MU-MIMO Uplink enabled. A value of 'false' indicates 802.11be MU-MIMO Uplink disabled. | |||||||||||||||||||||
| CcLMultiBSSIDProfile11beOfdmaMultiRU | 1.3.6.1.4.1.9.9.778.1.1.7.1.14 | TruthValue | RC | ||||||||||||||||||
column · TruthValue · read-create · current This object specifies if 802.11be OFDMA Multiple Resource Unit is enabled. A value of 'true' indicates 802.11be OFDMA Multi-RU is enabled. A value of 'false' indicates 802.11be OFDMA Multi-RU is disabled. | |||||||||||||||||||||
| NciscoLwappRFGlobalObjects | 1.3.6.1.4.1.9.9.778.1.2 | ||||||||||||||||||||
| ScLRFProfileOutOfBoxAPConfig | 1.3.6.1.4.1.9.9.778.1.2.1 | TruthValue | RW | ||||||||||||||||||
scalar · TruthValue · read-write · current This object specifies the out of box AP config feature. Enabling this feature will allow any AP that does not have group name configured upon join to controller then it will be considered as out of box AP and it will be moved to a special AP Group. Disabling this feature will only stop further subscription of new AP's to Out of Box AP group. A value of 'true' indicates that out of box AP feature is enabled and APs will be moved to newly created AP group out-of-box and shut of their radios. A value of 'false' indicates that out of box AP feature is disabled. | |||||||||||||||||||||
| ScLRFProfileOutOfBoxAPPersistenceConfig | 1.3.6.1.4.1.9.9.778.1.2.2 | TruthValue | RW | ||||||||||||||||||
scalar · TruthValue · read-write · current This object specifies the out of box AP group to be persistent or not. A value of 'true' indicates out-of-box persistence need to be enabled. A value of 'false' indicates out-of-box persistence need to be disabled. | |||||||||||||||||||||
| NciscoLwappRFMIBConform | 1.3.6.1.4.1.9.9.778.2 | ||||||||||||||||||||
| NciscoLwappRFMIBCompliances | 1.3.6.1.4.1.9.9.778.2.1 | ||||||||||||||||||||
| MciscoLwappRFMIBCompliance | 1.3.6.1.4.1.9.9.778.2.1.1 | deprecated | |||||||||||||||||||
compliance · deprecated The compliance statement for the SNMP entities that implement the ciscoLwappRFMIB module. This compliance is deprecated and replaced by ciscoLwappRFMIBComplianceVer1 .
| |||||||||||||||||||||
| MciscoLwappRFMIBComplianceVer1 | 1.3.6.1.4.1.9.9.778.2.1.2 | ||||||||||||||||||||
compliance · current The compliance statement for the SNMP entities that implement the ciscoLwappRFMIB module. | |||||||||||||||||||||
| MciscoLwappRFMIBComplianceVer2 | 1.3.6.1.4.1.9.9.778.2.1.3 | ||||||||||||||||||||
compliance · current The compliance statement for the SNMP entities that implement the ciscoLwappRFMIB module. Added ciscoLwappRFConfigGroup2 to add object to raise trap when client count exceeds threshold and ciscoLwappRFConfigGroup3 to address DCA settings | |||||||||||||||||||||
| MciscoLwappRFMIBComplianceRev3 | 1.3.6.1.4.1.9.9.778.2.1.4 | ||||||||||||||||||||
compliance · current The compliance statement for the SNMP entities that implement the ciscoLwappRFMIB module. | |||||||||||||||||||||
| MciscoLwappRFMIBComplianceRev4 | 1.3.6.1.4.1.9.9.778.2.1.5 | ||||||||||||||||||||
compliance · current The compliance statement for the SNMP entities that implement the ciscoLwappRFMIB module.
| |||||||||||||||||||||
| MciscoLwappRFMIBComplianceRev5 | 1.3.6.1.4.1.9.9.778.2.1.6 | ||||||||||||||||||||
compliance · current The compliance statement for the SNMP entities that implement the ciscoLwappRFMIB module.
| |||||||||||||||||||||
| MciscoLwappRFMIBComplianceRev6 | 1.3.6.1.4.1.9.9.778.2.1.7 | ||||||||||||||||||||
compliance · current The compliance statement for the SNMP entities that implement the ciscoLwappRFMIB module.
| |||||||||||||||||||||
| MciscoLwappRFMIBComplianceRev7 | 1.3.6.1.4.1.9.9.778.2.1.8 | ||||||||||||||||||||
compliance · current The compliance statement for the SNMP entities that implement the ciscoLwappRFMIB module.
| |||||||||||||||||||||
| NciscoLwappRFMIBGroups | 1.3.6.1.4.1.9.9.778.2.2 | ||||||||||||||||||||
| GciscoLwappRFConfigGroup | 1.3.6.1.4.1.9.9.778.2.2.1 | deprecated | |||||||||||||||||||
group · deprecated This collection of objects specifies the configuration of RF parameters on the controller to be passed to an LWAPP AP.This config group ciscoLwappRFConfigGroup is deprecated and replaced by ciscoLwappRFConfigGroupVer1
| |||||||||||||||||||||
| GciscoLwappRFConfigGroupVer1 | 1.3.6.1.4.1.9.9.778.2.2.2 | ||||||||||||||||||||
group · current This collection of objects specifies the configuration of RF parameters on the controller to be passed to an LWAPP AP.
| |||||||||||||||||||||
| GciscoLwappRFConfigGroup1 | 1.3.6.1.4.1.9.9.778.2.2.3 | ||||||||||||||||||||
group · current This collection of objects specifies the configuration of RF parameters on the controller to be passed to an LWAPP AP.
| |||||||||||||||||||||
| GciscoLwappRFGlobalConfigGroup | 1.3.6.1.4.1.9.9.778.2.2.4 | ||||||||||||||||||||
| GciscoLwappRFGroupTrapThresholdConfig | 1.3.6.1.4.1.9.9.778.2.2.5 | ||||||||||||||||||||
group · current This object specifies the configuration of Trap threshold to be configured on the interface of an LWAPP AP. | |||||||||||||||||||||
| GciscoLwappRFConfigGroup3 | 1.3.6.1.4.1.9.9.778.2.2.6 | ||||||||||||||||||||
group · current This object specifies the configuration DCA for RF Profiles. | |||||||||||||||||||||
| GciscoLwappRFConfigGroup4 | 1.3.6.1.4.1.9.9.778.2.2.7 | ||||||||||||||||||||
group · current This object specifies the receiver start of packet threshold for RF Profiles. | |||||||||||||||||||||
| GciscoLwappRFGroupDCAChannelConfig | 1.3.6.1.4.1.9.9.778.2.2.8 | deprecated | |||||||||||||||||||
group · deprecated This object specifies the add and remove channels for RF Profiles.
| |||||||||||||||||||||
| GciscoLwappRFGroupChannelConfig | 1.3.6.1.4.1.9.9.778.2.2.9 | ||||||||||||||||||||
group · current This object specifies the add and remove channels for RF Profiles. | |||||||||||||||||||||
| GciscoLwappRFConfigGroupExtension1 | 1.3.6.1.4.1.9.9.778.2.2.10 | ||||||||||||||||||||
group · current This object specifies the configuration of RF parameters on the controller to be passed to an LWAPP AP. | |||||||||||||||||||||
| GciscoLwappRFConfigGroup5 | 1.3.6.1.4.1.9.9.778.2.2.11 | ||||||||||||||||||||
group · current This object specifies the receiver start of packet threshold for RF Profiles. | |||||||||||||||||||||
| GciscoLwappRFConfigGroup6 | 1.3.6.1.4.1.9.9.778.2.2.12 | ||||||||||||||||||||
group · current This collection of object specifies the configuration of AirTime Fairness parameters. | |||||||||||||||||||||
| GciscoLwappRFConfigGroup7 | 1.3.6.1.4.1.9.9.778.2.2.13 | ||||||||||||||||||||
group · current This collection of object specifies the removed channel and add channel list information from default DCA channel list for a RF profile | |||||||||||||||||||||
| GciscoLwappRFConfigGroup8 | 1.3.6.1.4.1.9.9.778.2.2.14 | ||||||||||||||||||||
group · current This collection of objects specifies the 802.11ax OBSS PD spatial reuse configurations for RF Profiles. | |||||||||||||||||||||
| GciscoLwappRFConfigGroup9 | 1.3.6.1.4.1.9.9.778.2.2.15 | ||||||||||||||||||||
group · current This collection of objects specifies the neighbor discovery mode for a RF profile
| |||||||||||||||||||||
| GciscoLwappRFConfigGroup10 | 1.3.6.1.4.1.9.9.778.2.2.16 | ||||||||||||||||||||
group · current This collection of objects specifies the 802.11ax Broadcast Probe response, FILS Discovery and PSC bias configurations for RF Profiles.
| |||||||||||||||||||||
Textual conventions
CiscoLwappRFApDataRatesINTEGERdisabled(0)mandatoryRate(2)notApplicable(3)supported(1)This field indicates the data rates supported by an AP 'disabled' The rate is not supported by the AP 'supported' The rate is supported by the AP 'mandatoryRate' The rate is required by the AP 'notApplicable' The rate is notApplicable.
Groups and compliance
- ciscoLwappRFConfigGroup
- ciscoLwappRFConfigGroup1
- ciscoLwappRFConfigGroup10
- ciscoLwappRFConfigGroup3
- ciscoLwappRFConfigGroup4
- ciscoLwappRFConfigGroup5
- ciscoLwappRFConfigGroup6
- ciscoLwappRFConfigGroup7
- ciscoLwappRFConfigGroup8
- ciscoLwappRFConfigGroup9
- ciscoLwappRFConfigGroupExtension1
- ciscoLwappRFConfigGroupVer1
- ciscoLwappRFGlobalConfigGroup
- ciscoLwappRFGroupChannelConfig
- ciscoLwappRFGroupDCAChannelConfig
- ciscoLwappRFGroupTrapThresholdConfig
- ciscoLwappRFMIBCompliance
- ciscoLwappRFMIBComplianceRev3
- ciscoLwappRFMIBComplianceRev4
- ciscoLwappRFMIBComplianceRev5
- ciscoLwappRFMIBComplianceRev6
- ciscoLwappRFMIBComplianceRev7
- ciscoLwappRFMIBComplianceVer1
- ciscoLwappRFMIBComplianceVer2