CISCO-LWAPP-DOT11-CLIENT-MIB
ciscoSystemsThis MIB is intended to be implemented on all those
devices operating as Central controllers, that
terminate the Light Weight Access Point Protocol
tunnel from Cisco Light-weight LWAPP Access Points.
Information provided by this MIB is about the
configuration and monitoring of 802.11 wireless
clients in the network.
The relationship between CC and the LWAPP APs
can be depicted as follows:
+......+ +......+ +......+ +......+
+ + + + + + + +
+ CC + + CC + + CC + + CC +
+ + + + + + + +
+......+ +......+ +......+ +......+
.. . . .
.. . . .
. . . . .
. . . . .
. . . . .
. . . . .
+......+ +......+ +......+ +......+ +......+
+ + + + + + + + + +
+ AP + + AP + + AP + + AP + + AP +
+ + + + + + + + + +
+......+ +......+ +......+ +......+ +......+
. . . .
. . . . .
. . . . .
. . . . .
. . . . .
+......+ +......+ +......+ +......+ +......+
+ + + + + + + + + +
+ MN + + MN + + MN + + MN + + MN +
+ + + + + + + + + +
+......+ +......+ +......+ +......+ +......+
The LWAPP tunnel exists between the controller and
the APs. The MNs communicate with the APs through
the protocol defined by the 802.11 standard.
LWAPP APs, upon bootup, discover and join one of the
controllers and the controller pushes the configuration,
that includes the WLAN parameters, to the LWAPP APs.
The APs then encapsulate all the 802.11 frames from
wireless clients inside LWAPP frames and forward
the LWAPP frames to the controller.
GLOSSARY
Access Point ( AP )
An entity that contains an 802.11 medium access
control ( MAC ) and physical layer ( PHY ) interface
and provides access to the distribution services via
the wireless medium for associated clients.
LWAPP APs encapsulate all the 802.11 frames in
LWAPP frames and sends them to the controller to which
it is logically connected.
Basic Service Set ( BSS )
Coverage area of one access point is called a BSS. An
access point (AP) acts as a master to control the
clients within that BSS.
Clear To Send (CTS)
Refer to the description of RTS.
Light Weight Access Point Protocol ( LWAPP )
This is a generic protocol that defines the
communication between the Access Points and the
Central Controller.
MAC Service Data Units ( MSDU )
The MSDU is that unit of data received from
the logical link control ( LLC ) sub-layer which lies
above the medium access control ( MAC ) sub-layer in a
protocol stack.
Message Integrity Code ( MIC )
A value generated by a symmetric key cryptographic
function. If the input data are changed, a new value
cannot be correctly computed without knowledge of the
symmetric key. Thus, the secret key protects the input
data from undetectable alteration.
Mobile Node ( MN )
A roaming 802.11 wireless device in a wireless
network associated with an access point. Mobile Node,
Mobile Station(Ms) and client are used
interchangeably.
Request To Send ( RTS )
A client wishing to send data initiates the process by
sending a Request To Send (RTS) frame. The destination
client replies with a Clear To Send (CTS) frame.
Wireless local-area network ( WLAN )
A local-area network that uses high-frequency radio
waves rather than wires to communicate between nodes.
Service Set Identifier (SSID)
A service set identifier is a name that identifies a
particular 802.11 wireless LAN. A client device
receives broadcast messages from all access points
within range advertising their SSIDs. The client
device can then either manually or automatically
based on configuration select the network with which
to associate. The SSID can be up to 32 characters long.
Hybrid Remote Edge Access Point (HREAP)
HREAP is a wireless solution for branch office and
remote office deployments. It enables customers to
configure and control access points in a branch or
remote office from the corporate office through a
wide area network (WAN) link without deploying a
controller in each office. HREAP is also known as
flexconnect.
Workgroup Bridge ( WGB )
A WGB can provide a wireless infrastructure connection
for a Ethernet-enabled devices. Devices that do not
have a wireless client adapter in order to connect to
the wireless network can be connected to a WGB through
Ethernet port.
KTS (Key Telephone System)
Key Telephone System is an alternative to a private
branch exchange (PBX) phone system. A KTS is equipped
with several buttons that allow a caller to directly
select outgoing lines or incoming calls, and use
intercom and conference facilities.
REFERENCE
[1] Wireless LAN Medium Access Control ( MAC ) and
Physical Layer ( PHY ) Specifications
[2] Draft-obara-capwap-lwapp-00.txt, IETF Light
Weight Access Point Protocolsnmptranslate -m CISCO-LWAPP-DOT11-CLIENT-MIB -Tpsnmpwalk -v2c -c <community> -m CISCO-LWAPP-DOT11-CLIENT-MIB <host> 1.3.6.1.4.1.9.9.599Imports
OID tree
| Name | OID | Type | Access | Status | Example | ||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| IciscoLwappDot11ClientMIB | 1.3.6.1.4.1.9.9.599 | ||||||||||||||||||||
identity This MIB is intended to be implemented on all those
devices operating as Central controllers, that
terminate the Light Weight Access Point Protocol
tunnel from Cisco Light-weight LWAPP Access Points.
Information provided by this MIB is about the
configuration and monitoring of 802.11 wireless
clients in the network.
The relationship between CC and the LWAPP APs
can be depicted as follows:
+......+ +......+ +......+ +......+
+ + + + + + + +
+ CC + + CC + + CC + + CC +
+ + + + + + + +
+......+ +......+ +......+ +......+
.. . . .
.. . . .
. . . . .
. . . . .
. . . . .
. . . . .
+......+ +......+ +......+ +......+ +......+
+ + + + + + + + + +
+ AP + + AP + + AP + + AP + + AP +
+ + + + + + + + + +
+......+ +......+ +......+ +......+ +......+
. . . .
. . . . .
. . . . .
. . . . .
. . . . .
+......+ +......+ +......+ +......+ +......+
+ + + + + + + + + +
+ MN + + MN + + MN + + MN + + MN +
+ + + + + + + + + +
+......+ +......+ +......+ +......+ +......+
The LWAPP tunnel exists between the controller and
the APs. The MNs communicate with the APs through
the protocol defined by the 802.11 standard.
LWAPP APs, upon bootup, discover and join one of the
controllers and the controller pushes the configuration,
that includes the WLAN parameters, to the LWAPP APs.
The APs then encapsulate all the 802.11 frames from
wireless clients inside LWAPP frames and forward
the LWAPP frames to the controller.
GLOSSARY
Access Point ( AP )
An entity that contains an 802.11 medium access
control ( MAC ) and physical layer ( PHY ) interface
and provides access to the distribution services via
the wireless medium for associated clients.
LWAPP APs encapsulate all the 802.11 frames in
LWAPP frames and sends them to the controller to which
it is logically connected.
Basic Service Set ( BSS )
Coverage area of one access point is called a BSS. An
access point (AP) acts as a master to control the
clients within that BSS.
Clear To Send (CTS)
Refer to the description of RTS.
Light Weight Access Point Protocol ( LWAPP )
This is a generic protocol that defines the
communication between the Access Points and the
Central Controller.
MAC Service Data Units ( MSDU )
The MSDU is that unit of data received from
the logical link control ( LLC ) sub-layer which lies
above the medium access control ( MAC ) sub-layer in a
protocol stack.
Message Integrity Code ( MIC )
A value generated by a symmetric key cryptographic
function. If the input data are changed, a new value
cannot be correctly computed without knowledge of the
symmetric key. Thus, the secret key protects the input
data from undetectable alteration.
Mobile Node ( MN )
A roaming 802.11 wireless device in a wireless
network associated with an access point. Mobile Node,
Mobile Station(Ms) and client are used
interchangeably.
Request To Send ( RTS )
A client wishing to send data initiates the process by
sending a Request To Send (RTS) frame. The destination
client replies with a Clear To Send (CTS) frame.
Wireless local-area network ( WLAN )
A local-area network that uses high-frequency radio
waves rather than wires to communicate between nodes.
Service Set Identifier (SSID)
A service set identifier is a name that identifies a
particular 802.11 wireless LAN. A client device
receives broadcast messages from all access points
within range advertising their SSIDs. The client
device can then either manually or automatically
based on configuration select the network with which
to associate. The SSID can be up to 32 characters long.
Hybrid Remote Edge Access Point (HREAP)
HREAP is a wireless solution for branch office and
remote office deployments. It enables customers to
configure and control access points in a branch or
remote office from the corporate office through a
wide area network (WAN) link without deploying a
controller in each office. HREAP is also known as
flexconnect.
Workgroup Bridge ( WGB )
A WGB can provide a wireless infrastructure connection
for a Ethernet-enabled devices. Devices that do not
have a wireless client adapter in order to connect to
the wireless network can be connected to a WGB through
Ethernet port.
KTS (Key Telephone System)
Key Telephone System is an alternative to a private
branch exchange (PBX) phone system. A KTS is equipped
with several buttons that allow a caller to directly
select outgoing lines or incoming calls, and use
intercom and conference facilities.
REFERENCE
[1] Wireless LAN Medium Access Control ( MAC ) and
Physical Layer ( PHY ) Specifications
[2] Draft-obara-capwap-lwapp-00.txt, IETF Light
Weight Access Point Protocol | |||||||||||||||||||||
| NciscoLwappDot11ClientMIBNotifs | 1.3.6.1.4.1.9.9.599.0 | ||||||||||||||||||||
| !ciscoLwappDot11ClientKeyDecryptError | 1.3.6.1.4.1.9.9.599.0.1 | ||||||||||||||||||||
notification · current This notification is generated when a decrypt error occurs. The WEP WPA or WPA2 Key configured at the station may be wrong. cldcAssociationMode represents the association mode for which the key decrypt error occurred. cldcApMacAddress represents the MacAddress of the AP to which the client is associated. cldcIfType represents the wireless interface type of the client. cLApName represents the name of the AP to which the client is associated. | |||||||||||||||||||||
| !ciscoLwappDot11ClientAssocNacAlert | 1.3.6.1.4.1.9.9.599.0.2 | ||||||||||||||||||||
notification · current This notification is generated when the client on NAC enabled SSIDs complete layer2 authentication . This is to inform about client's presence to the NAC appliance. cldcClientWlanProfileName represents the profile name of the WLAN, this 802.11 wireless client is connected to. cldcClientIPAddress represents the unique ipaddress of the client. cldcApMacAddress represents the MacAddress of the AP to which the client is associated. cldcClientQuarantineVLAN represents the quarantine VLAN for the client. cldcClientAccessVLAN represents the access VLAN for the client. | |||||||||||||||||||||
| !ciscoLwappDot11ClientDisassocNacAlert | 1.3.6.1.4.1.9.9.599.0.3 | ||||||||||||||||||||
notification · current This notification is generated when the controller removes the client entry on NAC enabled SSIDs. cldcClientWlanProfileName represents the profile name of the WLAN, this 802.11 wireless client is connected to. cldcClientIPAddress represents the unique ipaddress of the client. cldcApMacAddress represents the MacAddress of the AP to which the client is associated. cldcClientQuarantineVLAN represents the quarantine VLAN for the client. cldcClientAccessVLAN represents the access VLAN for the client. This is issued on NAC enabled ssids, whenever WLC removes client's entry. | |||||||||||||||||||||
| !ciscoLwappDot11ClientMovedToRunState | 1.3.6.1.4.1.9.9.599.0.4 | ||||||||||||||||||||
notification · current This notification is generated when the client completes the PEM state and moves to the RUN state. cldcClientUsername represents the username used by the client. cldcClientIPAddress represents the unique ipaddress of the client. cldcClientSSID represents the SSID of the WLAN to which the client is associated. cldcApMacAddress represents the MacAddress of the AP to which the client is associated. cLApDot11IfSlotId represents the slotId of the AP to which the client is associated. cLApName represents the name of the AP to which the client is associated. | |||||||||||||||||||||
| !ciscoLwappDot11ClientStaticIpFailTrap | 1.3.6.1.4.1.9.9.599.0.5 | ||||||||||||||||||||
notification · current This is issued whenever the subnet defined for the static IP of a client is not found. | |||||||||||||||||||||
| !ciscoLwappDot11ClientDisassocDataStatsTrap | 1.3.6.1.4.1.9.9.599.0.6 | ||||||||||||||||||||
notification · current The disassociate notification shall be sent when the Station sends a Disassociation frame. The value of the notification shall include the MAC address of the MAC to which the Disassociation frame was sent and the reason for the disassociation | |||||||||||||||||||||
| !ciscoLwappDot11ClientAssocDataStatsTrap | 1.3.6.1.4.1.9.9.599.0.7 | ||||||||||||||||||||
notification · current The associate notification shall be sent when the Station sends a association frame. | |||||||||||||||||||||
| !ciscoLwappDot11ClientSessionTrap | 1.3.6.1.4.1.9.9.599.0.8 | ||||||||||||||||||||
notification · current Issued when the client completes the PEM state and moves to the RUN state. | |||||||||||||||||||||
| !ciscoLwappDot11ClientAssocTrap | 1.3.6.1.4.1.9.9.599.0.9 | ||||||||||||||||||||
notification · current The notification shall be sent when the Station associats to controller.
| |||||||||||||||||||||
| !ciscoLwappDot11ClientDeAuthenticatedTrap | 1.3.6.1.4.1.9.9.599.0.10 | ||||||||||||||||||||
notification · current The notification shall be sent when the Station gets de-authenticated.
| |||||||||||||||||||||
| !ciscoLwappDot11ClientMovedToRunStateNewTrap | 1.3.6.1.4.1.9.9.599.0.11 | ||||||||||||||||||||
notification · current The notification shall be sent when the Station moves to run or authenticated state.
| |||||||||||||||||||||
| !ciscoLwappDot11ClientMobilityTrap | 1.3.6.1.4.1.9.9.599.0.12 | ||||||||||||||||||||
notification · current The notification shall be sent when the Station gets roamed.
| |||||||||||||||||||||
| !ciscoLwappDot11ClientMaxClientsReached | 1.3.6.1.4.1.9.9.599.0.13 | ||||||||||||||||||||
notification · current This notification is generated when the number of clients on the controller exceeds the limit defined by cldcMaxClientsTrapThreshold. | |||||||||||||||||||||
| NciscoLwappDot11ClientMIBObjects | 1.3.6.1.4.1.9.9.599.1 | ||||||||||||||||||||
| NcldcConfigObjects | 1.3.6.1.4.1.9.9.599.1.1 | ||||||||||||||||||||
| ScldcKeyDecryptErrorEnabled | 1.3.6.1.4.1.9.9.599.1.1.1 | TruthValue | RW | ||||||||||||||||||
scalar · TruthValue · read-write · current This object specifies the status of generation of ciscoLwappDot11ClientKeyDecryptError notification. A value of 'true' specifies that the agent generates ciscoLwappDot11ClientKeyDecryptError notification. A value of 'false' specifies that the agent doesn't generate ciscoLwappDot11ClientKeyDecryptError notification. | |||||||||||||||||||||
| ScldcAssocNacAlertEnabled | 1.3.6.1.4.1.9.9.599.1.1.2 | TruthValue | RW | ||||||||||||||||||
scalar · TruthValue · read-write · current This object specifies the status of generation of ciscoLwappDot11ClientAssocNacAlert notification. A value of 'true' specifies that the agent generates ciscoLwappDot11ClientAssocNacAlert notification. A value of 'false' specifies that the agent doesn't generate ciscoLwappDot11ClientAssocNacAlert notification. | |||||||||||||||||||||
| ScldcDisassocNacAlertEnabled | 1.3.6.1.4.1.9.9.599.1.1.3 | TruthValue | RW | ||||||||||||||||||
scalar · TruthValue · read-write · current This object specifies the control of generation of ciscoLwappDot11ClientDisassocNacAlert notification. A value of 'true' specifies that the agent generates ciscoLwappDot11ClientDisassocNacAlert notification. A value of 'false' specifies that the agent doesn't generate ciscoLwappDot11ClientDisassocNacAlert notification. | |||||||||||||||||||||
| ScldcMovedToRunStateEnabled | 1.3.6.1.4.1.9.9.599.1.1.4 | TruthValue | RW | ||||||||||||||||||
scalar · TruthValue · read-write · current This object specifies the control of generation of ciscoLwappDot11ClientMovedToRunState notification. A value of 'true' specifies that the agent generates ciscoLwappDot11ClientMovedToRunState notification. A value of 'false' specifies that the agent doesn't generate ciscoLwappDot11ClientMovedToRunState notification. | |||||||||||||||||||||
| SciscoLwappDot11ClientStaticIpFailTrapEnabled | 1.3.6.1.4.1.9.9.599.1.1.5 | TruthValue | RW | ||||||||||||||||||
scalar · TruthValue · read-write · current The object specifies the control of generation of ciscoLwappDot11ClientStaticIpFailTrap notification. A value of 'true' specifies that the agent generates ciscoLwappDot11ClientStaticIpFailTrap notification. A value of 'false' specifies that the agent doesn't generate ciscoLwappDot11ClientStaticIpFailTrap notification. | |||||||||||||||||||||
| ScldcMaxClientsTrapEnabled | 1.3.6.1.4.1.9.9.599.1.1.6 | TruthValue | RW | 1 | |||||||||||||||||
scalar · TruthValue · read-write · current This object specifies whether the ciscoLwappDot11ClientMaxClientsReached notification would be generated. A value of 'true' indicates that the agent generates ciscoLwappDot11ClientMaxClientsReached notifications. A value of 'false' indicates that the agent doesn't generate ciscoLwappDot11ClientMaxClientsReached notification. Example values from LibreNMS test devices
| |||||||||||||||||||||
| ScldcMaxClientsTrapThreshold | 1.3.6.1.4.1.9.9.599.1.1.7 | Unsigned32 (50..100) | RW | 75 | |||||||||||||||||
scalar · Unsigned32 (50..100) · read-write · current This object specifies the threshold for number of clients on the controller to trigger a trap. The trap ciscoLwappDot11ClientMaxClientsReached will be triggered once the count of clients on the controller reaches this limit and the ciscoLwappDot11ClientMaxClientsTrapEnabled is enabled. The admissible range goes from 50% to 100%.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| ScldcMaxClientsTrapPeriod | 1.3.6.1.4.1.9.9.599.1.1.8 | Unsigned32 (1..60) | RW | 5 | |||||||||||||||||
scalar · Unsigned32 (1..60) · read-write · current This object specifies the period of time for the controller to trigger a trap. The trap ciscoLwappDot11ClientMaxClientsReached will be triggered only once per period if ciscoLwappDot11ClientMaxClientsTrapEnabled is enabled. The admissible range goes from 1 minute to 60 minutes.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| NcldcNotifObjects | 1.3.6.1.4.1.9.9.599.1.2 | ||||||||||||||||||||
| ScldcClientRSSI | 1.3.6.1.4.1.9.9.599.1.2.1 | Integer32 | AN | ||||||||||||||||||
scalar · Integer32 · accessible-for-notify · current This object represents the average RSSI for the mobile station. | |||||||||||||||||||||
| ScldcClientSNR | 1.3.6.1.4.1.9.9.599.1.2.2 | Integer32 | AN | ||||||||||||||||||
scalar · Integer32 · accessible-for-notify · current This object represents the average SNR for the mobile station. | |||||||||||||||||||||
| ScldcDOT11ClientReasonCode | 1.3.6.1.4.1.9.9.599.1.2.3 | INTEGER | AN | ||||||||||||||||||
scalar · INTEGER · accessible-for-notify · current This object represents the reason code for failure of client association. A value of 'unspecified' represents that the reason for failure is not specified. A value 'previousAuthNotValid' represents that the reason for failure is previous authentication was not valid. A value of 'deauthenticationLeaving' represents that the reason for failure is leaving due to deauthentication. A value of 'disassociationDueToInactivity' represents that the reason for failure is disassociation due to inactivity. A value of 'disassociationAPBusy' represents that the reason for failure is disassociation since AP was busy. A value of 'class2FrameFromNonAuthStation' represents that the reason for failure is class 2 frame from non authenticated station. A value of 'class2FrameFromNonAssStation' represents that the reason for failure is class 2 frame from non associated station. A value of 'disassociationStaHasLeft' represents that the reason for failure is station has left due to disassociation. A value of 'staReqAssociationWithoutAuth' represents that the reason for failure is station send association request without authentication. A value of 'invalidInformationElement' represents that the reason for failure is invalid information element. A value of 'groupCipherInvalid' represents that the reason for failure is invalid group Cipher. A value of 'unicastCipherInvalid' represents that the reason for failure is invalid unicast cipher. A value of 'akmpInvalid' represents that the reason for failure is invalid key management protocol. A value of 'unsupportedRsnVersion' represents that the reason for failure is unsupported RSN version. A value of invalidRsnIeCapabilities' represents that the reason for failure is invalid RSN IE capabilities. A value of 'cipherSuiteRejected' represents that the reason for failure is cipher suite not valid. A value of 'missingReasonCode' represents that the reason for failure is reason code is missing. A value of 'maxAssociatedClientsReached' represents that the reason for failure is maximum allowed associated client number has reached. A value of 'maxAssociatedClientsReachedOnRadio' represents that the reason for failure is maximum allowed associated client number has reached on radio. A value of 'maxAssociatedClientsReachedOnWlan' represents that the reason for failure is maximum allowed associated client number has reached on wlan. A value of 'unSpecifiedQosFailure' represents that the reason for failure is QoS not supported. A value of 'qosPolicyMismatch' represents that the reason for failure is mismatch on QOS policy. A value of 'inSufficientBandwidth' represents that the reason for failure is insufficient bandwidth. A value of 'inValidQosParams' represents that the reason for failure is invalid QOS parameters.
| |||||||||||||||||||||
| ScldcDOT11ClientTxDataPackets | 1.3.6.1.4.1.9.9.599.1.2.4 | Counter32 | AN | ||||||||||||||||||
scalar · Counter32 · accessible-for-notify · current This object represents the number of data packets sent by this mobile station | |||||||||||||||||||||
| ScldcDOT11ClientTxDataBytes | 1.3.6.1.4.1.9.9.599.1.2.5 | Counter32 | AN | ||||||||||||||||||
scalar · Counter32 · accessible-for-notify · current This object represents the number of data bytes sent by this mobile station | |||||||||||||||||||||
| ScldcDOT11ClientRxDataPackets | 1.3.6.1.4.1.9.9.599.1.2.6 | Counter32 | AN | ||||||||||||||||||
scalar · Counter32 · accessible-for-notify · current This object represents the number of data packets sent for this mobile station | |||||||||||||||||||||
| ScldcDOT11ClientRxDataBytes | 1.3.6.1.4.1.9.9.599.1.2.7 | Counter32 | AN | ||||||||||||||||||
scalar · Counter32 · accessible-for-notify · current This object represents the number of data bytes sent for this mobile station | |||||||||||||||||||||
| ScldcClientVlanId | 1.3.6.1.4.1.9.9.599.1.2.8 | Integer32 (0..4096) | AN | ||||||||||||||||||
scalar · Integer32 (0..4096) · accessible-for-notify · current This object represents VLAN ID of the interface to which the client is associated. | |||||||||||||||||||||
| ScldcClientPolicyType | 1.3.6.1.4.1.9.9.599.1.2.9 | INTEGER | AN | ||||||||||||||||||
scalar · INTEGER · accessible-for-notify · current This object represents security policy type on which the mobile station is associated. A value of 'dot1x' represents the policy type as dot1x. A value of 'wpa1' represents the policy type as WPA version 1. A value of 'wpa2' represents the policy type as WPA version 2. A value of 'wpa2vff' represents the policy type as WPA2VFF. A value of 'notavailable' represents the policy type is not available. A value of 'unknown' represents the policy type is not known. A value of 'wapi' represents the policy type as WAPI.
| |||||||||||||||||||||
| ScldcClientEapType | 1.3.6.1.4.1.9.9.599.1.2.10 | INTEGER | AN | ||||||||||||||||||
scalar · INTEGER · accessible-for-notify · current This object represents EAP policy type used by the mobile station during association. A value of 'eapTls' represents the EAP policy type as EAP-TLS. A value of 'ttls' represents the EAP policy type as TTLS. A value of 'peap' represents the EAP policy type as PEAP. A value of 'leap' represents the EAP policy type as LEAP. A value of 'speke' represents the EAP policy type as EAP-SPEKE. A value of 'eapFast' represents the EAP policy type as EAP-FAST. A value of 'notavailable' represents the EAP policy type is not available A value of 'unknown' represents the EAP policy type is not known.
| |||||||||||||||||||||
| ScldcClientAID | 1.3.6.1.4.1.9.9.599.1.2.11 | Unsigned32 | AN | ||||||||||||||||||
scalar · Unsigned32 · accessible-for-notify · current This object represents the AID allocated for the mobile station | |||||||||||||||||||||
| ScldcClientAuthenticationAlgorithm | 1.3.6.1.4.1.9.9.599.1.2.12 | INTEGER | AN | ||||||||||||||||||
scalar · INTEGER · accessible-for-notify · current This object represents the authentication algorithm of mobile station used for authentication. A value of 'openSystem' represents that the client used open system algorithm to get authenticated. A value of 'sharedKey' represents that the client used shared key algorithm to get authenticated. A value of 'unknown' represents that the algorithm used for authentication is not known. A value of 'openAndEap' represents that the client used open system and EAP algorithm to get authenticated.
| |||||||||||||||||||||
| ScldcClientWepState | 1.3.6.1.4.1.9.9.599.1.2.13 | INTEGER | AN | ||||||||||||||||||
scalar · INTEGER · accessible-for-notify · current This object represents the WEP state of the mobile station. A value of 'enable' represents WEP state is enabled. A value of 'disable' represents WEP state is disbaled.
| |||||||||||||||||||||
| ScldcClientEncryptionCipher | 1.3.6.1.4.1.9.9.599.1.2.14 | INTEGER | AN | ||||||||||||||||||
scalar · INTEGER · accessible-for-notify · current This object represents encryption cipher selected for encryption of mobile station traffic. A value of 'ccmpAes' represents the encryption used is CCMP AES. A value of 'tkipMic' represents the encryption used is TKIP-MIC. A value of 'wep40' represents the encryption used is WEP40. A value of 'wep104' represents the encryption used is WEP104. A value of 'wep128' represents the encryption used is WEP128. A value of 'none' represents the no encryption used. A value of 'notavailable' represents the encryption used is not available. A value of 'unknown' represents the encryption is used is not known. A value of 'wapiSMS4' represents the encryption is used is WAPI-SMS4.
| |||||||||||||||||||||
| ScldcClientPortNumber | 1.3.6.1.4.1.9.9.599.1.2.15 | Unsigned32 | AN | ||||||||||||||||||
scalar · Unsigned32 · accessible-for-notify · current This object represents the port number of this airespace switch on which the traffic of the mobile station is coming through. | |||||||||||||||||||||
| ScldcClientAnchorAddressType | 1.3.6.1.4.1.9.9.599.1.2.16 | InetAddressType | AN | ||||||||||||||||||
scalar · InetAddressType · accessible-for-notify · current This object represents mobility anchor address type. | |||||||||||||||||||||
| ScldcClientAnchorAddress | 1.3.6.1.4.1.9.9.599.1.2.17 | InetAddress | AN | ||||||||||||||||||
scalar · InetAddress · accessible-for-notify · current This object represent anchor IP address. If the mobility status of the mobile station is anchor then it will have peer Ip address and will have anchor IP if the role is foreign | |||||||||||||||||||||
| ScldcClientEssIndex | 1.3.6.1.4.1.9.9.599.1.2.18 | Unsigned32 (1..517) | AN | ||||||||||||||||||
scalar · Unsigned32 (1..517) · accessible-for-notify · current This object represents the ESS index of the WLAN(SSID) that is being used by mobile station to connect to AP | |||||||||||||||||||||
| ScldcClientCcxVersion | 1.3.6.1.4.1.9.9.599.1.2.19 | INTEGER | AN | ||||||||||||||||||
scalar · INTEGER · accessible-for-notify · current This object represents the Cisco Compatible Extensions (CCX) version the client is using for communication with the AP. A value of 'notSupported' represents CCX version is not supported. A value of 'ccxv1' represents that client used CCX version 1 for communication. A value of 'ccxv2' represents that client used CCX version 2 for communication. A value of 'ccxv3' represents that client used CCX version 3 for communication. A value of 'ccxv4' represents that client used CCX version 4 for communication. A value of 'ccxv5' represents that client used CCX version 5 for communication. A value of 'ccxv6' represents that client used CCX version 6 for communication.
| |||||||||||||||||||||
| ScldcClientE2eVersion | 1.3.6.1.4.1.9.9.599.1.2.20 | INTEGER | AN | ||||||||||||||||||
scalar · INTEGER · accessible-for-notify · current This object represents the End-2-End Version the client is using for communication with the AP. A value of 'notSupported' represents end-2-end version is not supported. A value of 'e2ev1' represents end-2-end version used by mobile station is 1. A value of 'e2ev2' represents end-2-end version used by mobile station is 2.
| |||||||||||||||||||||
| ScldcClientInterface | 1.3.6.1.4.1.9.9.599.1.2.21 | SnmpAdminString (SIZE (0..32)) | AN | ||||||||||||||||||
scalar · SnmpAdminString (SIZE (0..32)) · accessible-for-notify · current This object represents the name of the interface of the mobile client on which traffic sent to the switch. | |||||||||||||||||||||
| ScldcClientMobilityStatus | 1.3.6.1.4.1.9.9.599.1.2.22 | INTEGER | AN | ||||||||||||||||||
scalar · INTEGER · accessible-for-notify · current This object represents the mobility role of the mobile station. A value of 'unassociated' represents mobility role is not associated. A value of 'local' represents mobility role is local. A value of 'anchor' represents mobility role is anchor. A value of 'foreign' represents mobility role is foreign. A value of 'handoff' represents mobility role is handoff. A value of 'unknown' represents mobility role is not known. A value of 'exportanchor' represents mobility role is exportanchor. A value of 'exportforeign' represents mobility role is exportforeign.
| |||||||||||||||||||||
| ScldcClientStatusCode | 1.3.6.1.4.1.9.9.599.1.2.23 | INTEGER (0..65535) | AN | ||||||||||||||||||
scalar · INTEGER (0..65535) · accessible-for-notify · current This object represents status code of the mobile station | |||||||||||||||||||||
| ScldcClientDeleteAction | 1.3.6.1.4.1.9.9.599.1.2.24 | INTEGER | AN | ||||||||||||||||||
scalar · INTEGER · accessible-for-notify · current This object represents the action to deauthenticate the mobile station. A value of 'default' represents the state as default. A value of 'delete' represents the state as delete.
| |||||||||||||||||||||
| ScldcClientSecurityPolicyStatus | 1.3.6.1.4.1.9.9.599.1.2.25 | INTEGER | AN | ||||||||||||||||||
scalar · INTEGER · accessible-for-notify · current This object represents the security policy state of the mobile station. A value of 'completed' represents the mobile station has completed the security policy checks. A value of 'notcompleted' represents policy checks are yet to be completed for the mobile station.
| |||||||||||||||||||||
| ScldcClientTrapEventTime | 1.3.6.1.4.1.9.9.599.1.2.26 | TimeTicks | AN | ||||||||||||||||||
scalar · TimeTicks · accessible-for-notify · current This object represents the trap event time of the client. | |||||||||||||||||||||
| ScldcClientPolicyManagerState | 1.3.6.1.4.1.9.9.599.1.2.27 | SnmpAdminString | AN | ||||||||||||||||||
scalar · SnmpAdminString · accessible-for-notify · current This object represents the current policy enforcement manager state of the client in controller. | |||||||||||||||||||||
| ScldcClientAssocTime | 1.3.6.1.4.1.9.9.599.1.2.28 | TimeStamp | AN | ||||||||||||||||||
scalar · TimeStamp · accessible-for-notify · current This object represents the time at which client associated | |||||||||||||||||||||
| ScldcClientPmipDataValid | 1.3.6.1.4.1.9.9.599.1.2.29 | TruthValue | AN | ||||||||||||||||||
scalar · TruthValue · accessible-for-notify · current This object represents whether client has valid PMIP data. | |||||||||||||||||||||
| ScldcClientMobilityExtDataValid | 1.3.6.1.4.1.9.9.599.1.2.30 | TruthValue | AN | ||||||||||||||||||
scalar · TruthValue · accessible-for-notify · current This object represents new mobility status. | |||||||||||||||||||||
| ScldcClientPolicyErrors | 1.3.6.1.4.1.9.9.599.1.2.31 | Counter64 | AN | ||||||||||||||||||
scalar · Counter64 · accessible-for-notify · current This object represents the number of policy errors for mobile station | |||||||||||||||||||||
| ScldcClientSessionId | 1.3.6.1.4.1.9.9.599.1.2.32 | SnmpAdminString | AN | ||||||||||||||||||
scalar · SnmpAdminString · accessible-for-notify · current This object represents the session to which the client is associated. | |||||||||||||||||||||
| ScldcClientPmipNai | 1.3.6.1.4.1.9.9.599.1.2.33 | SnmpAdminString | AN | ||||||||||||||||||
scalar · SnmpAdminString · accessible-for-notify · current This object represents the name of the profile, the client is associated to. | |||||||||||||||||||||
| ScldcClientPmipState | 1.3.6.1.4.1.9.9.599.1.2.34 | SnmpAdminString | AN | ||||||||||||||||||
scalar · SnmpAdminString · accessible-for-notify · current This object indicates the state of the PMIP client:
null: binding doesn't exist
init: binding created, Retx timer running for PBU, binding not
yet accepted from LMA, Tunnel/route is not yet setup
active: binding accepted by LMA, refresh timer running,
Tunnel/route setup complete.
refreshPending: Refresh timer expired and Retx timer running.
PBU refresh sent, PBA not yet received from LMA,
(Tunnel/route is already setup).
disconnectingSt: Dereg reply is expected. Retx timer is
running, tunnel/route is still setup. | |||||||||||||||||||||
| ScldcClientPmipInterface | 1.3.6.1.4.1.9.9.599.1.2.35 | SnmpAdminString (SIZE (1..32)) | AN | ||||||||||||||||||
scalar · SnmpAdminString (SIZE (1..32)) · accessible-for-notify · current This object indicates the interface to which the client is associated. | |||||||||||||||||||||
| ScldcClientPmipHomeAddrType | 1.3.6.1.4.1.9.9.599.1.2.36 | InetAddressType | AN | ||||||||||||||||||
scalar · InetAddressType · accessible-for-notify · current This object indicates the type of the Client's Home address made available through cldcClientPmipHomeAddress. | |||||||||||||||||||||
| ScldcClientPmipHomeAddr | 1.3.6.1.4.1.9.9.599.1.2.37 | InetAddress | AN | ||||||||||||||||||
scalar · InetAddress · accessible-for-notify · current This object indicates the Home Address of the client. | |||||||||||||||||||||
| ScldcClientPmipAtt | 1.3.6.1.4.1.9.9.599.1.2.38 | INTEGER | AN | ||||||||||||||||||
scalar · INTEGER · accessible-for-notify · current This object indicates the access technology type by which the client is currently attached. A value of 'reserved' indicates this value is reserved for future use. A value of 'logicalNetworkInterface' indicates that the client used logical network interface to connect to network. A value of 'pointToPointInterface' indicates that the client used point to point interface to connect to network. A value of 'ethernet' indicates that the client used ethernet to connect to network. A value of 'wirelessLan' indicates that the client used wireless LAN to connect to network. A value of 'wimax' indicates that the client used WiMAX technology to connect to network. A value of 'threeGPPGERAN' indicates that the client used threeGPPGERAN technology to connect to network. A value of 'threeGPPUTRAN' indicates that the client used threeGPPUTRAN technology to connect to network. A value of 'threeGPPETRAN' indicates that the client used threeGPPETRAN technology to connect to network. A value of 'threeGPP2eHRPD' indicates that the client used threeGPP2eHRPD technology to connect to network. A value of 'threeGPP2HRPD' indicates that the client used threeGPP2HRPD technology to connect to network. A value of 'threeGPP21xRTT' indicates that the client used threeGPP21xRTT technology to connect to network. A value of 'threeGPP2UMB' indicates that the client used threeGPP2UMB technology to connect to network.
| |||||||||||||||||||||
| ScldcClientPmipLocalLinkId | 1.3.6.1.4.1.9.9.599.1.2.39 | MacAddress | AN | ||||||||||||||||||
scalar · MacAddress · accessible-for-notify · current This object indicates the local link identifier of the client. | |||||||||||||||||||||
| ScldcClientPmipLmaName | 1.3.6.1.4.1.9.9.599.1.2.40 | SnmpAdminString | AN | ||||||||||||||||||
scalar · SnmpAdminString · accessible-for-notify · current This object indicates the LMA to which the client is connected. | |||||||||||||||||||||
| ScldcClientPmipLifeTime | 1.3.6.1.4.1.9.9.599.1.2.41 | TimeTicks | AN | ||||||||||||||||||
scalar · TimeTicks · accessible-for-notify · current This object indicates the duration of the PMIP client association. | |||||||||||||||||||||
| ScldcClientPmipDomainName | 1.3.6.1.4.1.9.9.599.1.2.42 | SnmpAdminString | AN | ||||||||||||||||||
scalar · SnmpAdminString · accessible-for-notify · current This object indicates the domain to which the PMIP client is associated. | |||||||||||||||||||||
| ScldcClientPmipUpKey | 1.3.6.1.4.1.9.9.599.1.2.43 | Unsigned32 | AN | ||||||||||||||||||
scalar · Unsigned32 · accessible-for-notify · current This object indicates the upstream key of the PMIP client. | |||||||||||||||||||||
| ScldcClientPmipDownKey | 1.3.6.1.4.1.9.9.599.1.2.44 | Unsigned32 | AN | ||||||||||||||||||
scalar · Unsigned32 · accessible-for-notify · current This object indicates the downstream key of the PMIP client. | |||||||||||||||||||||
| ScldcMaxClientsCount | 1.3.6.1.4.1.9.9.599.1.2.45 | Unsigned32 | AN | ||||||||||||||||||
scalar · Unsigned32 · accessible-for-notify · current This object represents the number of clients joined to the controller when ciscoLwappDot11ClientMaxClientsReached is sent. | |||||||||||||||||||||
| ScldcMaxThresholdReachedClear | 1.3.6.1.4.1.9.9.599.1.2.46 | TruthValue | AN | ||||||||||||||||||
scalar · TruthValue · accessible-for-notify · current This object represents whether ciscoLwappDot11ClientMaxClientsReached is raise or clear. A value of 'true' indicates that this event is cleared A value of 'false' indicates that this event is raised. | |||||||||||||||||||||
| NcldcStatusObjects | 1.3.6.1.4.1.9.9.599.1.3 | ||||||||||||||||||||
| TcldcClientTable | 1.3.6.1.4.1.9.9.599.1.3.1 | NA | |||||||||||||||||||
table · not-accessible · current This table represents the 802.11 wireless clients that are associated with the APs that have joined this controller. An entry is created automatically by the controller when the client gets associated to the AP. An existing entry gets deleted when the association gets dropped. Each client added to this table is uniquely identified by the client's MAC address. | |||||||||||||||||||||
| RcldcClientEntry | 1.3.6.1.4.1.9.9.599.1.3.1.1 | NA | |||||||||||||||||||
row · not-accessible · current Each entry represents a conceptual row in this table and provides the information about the clients associated to the APs that have joined the controller. An entry is identified the client's MAC address.
| |||||||||||||||||||||
| CcldcClientMacAddress | 1.3.6.1.4.1.9.9.599.1.3.1.1.1 | MacAddress | NA | ||||||||||||||||||
column · MacAddress · not-accessible · current This object represents the MAC address of the client for this entry and uniquely identifies this entry. | |||||||||||||||||||||
| CcldcClientStatus | 1.3.6.1.4.1.9.9.599.1.3.1.1.2 | CLDot11ClientStatus | RO | 3 | |||||||||||||||||
column · CLDot11ClientStatus · read-only · current This object represents the current status of the client. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcldcClientWlanProfileName | 1.3.6.1.4.1.9.9.599.1.3.1.1.3 | SnmpAdminString (SIZE (0..32)) | RO | SAP_WLAN | |||||||||||||||||
column · SnmpAdminString (SIZE (0..32)) · read-only · current This object represents the WLAN profile name this 802.11 wireless client is connected to. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcldcClientWgbStatus | 1.3.6.1.4.1.9.9.599.1.3.1.1.4 | INTEGER | RO | regClient(1) | |||||||||||||||||
column · INTEGER · read-only · current This object represents the work group bridging status of a DOT11 client. A value of 'regClient' represents that the client is a wireless client A value of 'wgbClient' represents that the client is connected via a WGB A value of 'wgb' represents that the client is the WGB itself.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcldcClientWgbMacAddress | 1.3.6.1.4.1.9.9.599.1.3.1.1.5 | MacAddress | RO | 00:00:00:00:00:00 | |||||||||||||||||
column · MacAddress · read-only · current This object represents the MAC address of the WGB this 802.11 wireless client to which it is connected. This returns a non-zero value when the cldcClientWgbStatus is wgbClient. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcldcClientProtocol | 1.3.6.1.4.1.9.9.599.1.3.1.1.6 | INTEGER | RO | dot11n24(6) | |||||||||||||||||
column · INTEGER · read-only · current This object represents 802.11 protocol type of the client it used to join to wireless network. A value of 'dot11a' represents that the client is using 802.11a standard to connect to the access point (AP) A value of 'dot11b' represents that the client is using 802.11b standard to connect to the access point (AP) A value of 'dot11g' represents that the client is using 802.11g standard to connect to the access point (AP) A value of 'unknown' represents that the client protocol is unknown A value of 'mobile' represents that the client using mobile wireless to connect to the access point (AP). A value of 'dot11n24' represents that the client is using 802.11n standard with 2.4 GHz frequency to connect to the access point (AP) A value of 'dot11n5' represents that the client is using 802.11n standard with 5 GHz frequency to connect to the access point (AP). A value of 'ethernet' represents that the client is using ethernet standard to connect to the access point (AP). A value of 'dot3' represents that the client is using dot3 standard to connect to the access point (AP). A value of 'dot11ac5' represents that the client is using 802.11ac standard with 5 GHz frequency to connect to the access point (AP).
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcldcAssociationMode | 1.3.6.1.4.1.9.9.599.1.3.1.1.7 | INTEGER | RO | wpa2(4) | |||||||||||||||||
column · INTEGER · read-only · current This object represents the association mode used by client for protected wireless traffic. A value of 'unknown' represents that association mode used by client for wilress traffic encryption is not known. A value of 'wep' represents that association mode used by client for wilress traffic encryption is WEP. A value of 'wpa' represents that association mode used by client for wilress traffic encryption is WPA. A value of 'wpa2' represents that association mode used by client for wilress traffic encryption is WPA2.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcldcApMacAddress | 1.3.6.1.4.1.9.9.599.1.3.1.1.8 | MacAddress | RO | 08:7b:87:14:1b:1c | |||||||||||||||||
column · MacAddress · read-only · current This object represents the radio MAC address of a LWAPP AP. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcldcIfType | 1.3.6.1.4.1.9.9.599.1.3.1.1.9 | CLApIfType | RO | 1 | |||||||||||||||||
column · CLApIfType · read-only · current This object represents the wireless interface type. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcldcClientIPAddress | 1.3.6.1.4.1.9.9.599.1.3.1.1.10 | IpAddress | RO | ||||||||||||||||||
column · IpAddress · read-only · current This object represents client's IP address. This is learnt from the client details when the client associates with the access point. | |||||||||||||||||||||
| CcldcClientNacState | 1.3.6.1.4.1.9.9.599.1.3.1.1.11 | INTEGER | RW | access(2) | |||||||||||||||||
column · INTEGER · read-write · current This object specifies that client's network admission control state. A value of 'quarantine' specifies that client goes through posture analysis and the client traffic is sent by controller in quarantine vlan. A value of 'access' specifies that client traffic is sent by controller in access vlan. The client should have completed posture analysis. Posture Analysis is a state change where the client applies the configured policies to validate access to the network.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcldcClientQuarantineVLAN | 1.3.6.1.4.1.9.9.599.1.3.1.1.12 | VlanId | RO | ||||||||||||||||||
column · VlanId · read-only · current This object indicates the quarantine VLAN for client. The quarantine VLAN only allows limited access to the network. | |||||||||||||||||||||
| CcldcClientAccessVLAN | 1.3.6.1.4.1.9.9.599.1.3.1.1.13 | VlanId | RO | ||||||||||||||||||
column · VlanId · read-only · current This object indicates the access VLAN for client. The access VLAN allows unlimited access to the network. | |||||||||||||||||||||
| CcldcClientLoginTime | 1.3.6.1.4.1.9.9.599.1.3.1.1.14 | TimeStamp | RO | 1725292593 (199d 16h 28m 45s) | |||||||||||||||||
column · TimeStamp · read-only · current This object indicates the value of sysUpTime when the client logged in. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcldcClientUpTime | 1.3.6.1.4.1.9.9.599.1.3.1.1.15 | TimeInterval | RO | 191 | |||||||||||||||||
column · TimeInterval · read-only · current This object indicates the duration for which the client has been associated with this device.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcldcClientPowerSaveMode | 1.3.6.1.4.1.9.9.599.1.3.1.1.16 | CLClientPowerSaveMode | RO | 2 | |||||||||||||||||
column · CLClientPowerSaveMode · read-only · current This object indicates the power management mode of the client. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcldcClientCurrentTxRateSet | 1.3.6.1.4.1.9.9.599.1.3.1.1.17 | OCTET STRING (SIZE (2)) | RO | m4 | |||||||||||||||||
column · OCTET STRING (SIZE (2)) · read-only · current This object indicates the current data rate at which the client transmits and receives data. The data rate field is a 16-bit unsigned value expressing the data rate of the packets received by the client.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcldcClientDataRateSet | 1.3.6.1.4.1.9.9.599.1.3.1.1.18 | OCTET STRING (SIZE (1..126)) | RO | 11.0,12.0,18.0,24.0,36.0,48.0,54.0 | |||||||||||||||||
column · OCTET STRING (SIZE (1..126)) · read-only · current This object indicates the set of data rates at which the client may transmit data. Each client can support up to 126 rates. Each octet contains an integer value representing one of these 126 rates ranging from 1 Mb/s to 63.5 Mb/s. One of the supported rates will be chosen by the access point for transmission with the client. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcldcClientHreapApAuth | 1.3.6.1.4.1.9.9.599.1.3.1.1.19 | INTEGER | RO | notApplicable(3) | |||||||||||||||||
column · INTEGER · read-only · current This object indicates whether the client is locally authenticated or authenticated by the controller. Local authentication is done only if the Access Point connected to the client is of flexconnect mode. A value of 'true' indicates that the client is authenticated by the AP.. A value of 'false' indicates that the client is authenticated by the controller. A value of 'notApplicable' indicates that client is not connected to a flexconect AP.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcldcClient80211uCapable | 1.3.6.1.4.1.9.9.599.1.3.1.1.20 | TruthValue | RO | 2 | |||||||||||||||||
column · TruthValue · read-only · current This object indicates whether the client supports 802.11u feature. The 802.11u standard allows devices such as laptop computers or cellular phones to join a wireless LAN widely used in the home, office and some commercial establishments. A value of 'true' indicates that the client supports the 802.11u feature. A value of 'false' indicates that the client does not support the 802.11u feature. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcldcClientPostureState | 1.3.6.1.4.1.9.9.599.1.3.1.1.21 | TruthValue | RO | 2 | |||||||||||||||||
column · TruthValue · read-only · current This object indicates the posture state of the client. Posture Analysis is a state change where the client applies the configured policies to validate access to the network. A value of 'true' indicates that the client supports the posture feature. A value of 'false' indicates that the client does not support the posture feature. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcldcClientAclName | 1.3.6.1.4.1.9.9.599.1.3.1.1.22 | SnmpAdminString | RO | | |||||||||||||||||
column · SnmpAdminString · read-only · current This object indicates the ACL Name for the client. This ACL will be used to allow or block client traffic based on the list of rules attached to the ACL. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcldcClientAclApplied | 1.3.6.1.4.1.9.9.599.1.3.1.1.23 | INTEGER | RO | notAvailable(3) | |||||||||||||||||
column · INTEGER · read-only · current This object indicates the ACL applied status for the client. A value of 'true' indicates that the ACL is applied. A value of 'false' indicates that the ACL is not applied. A value of 'notAvailable' indicates that applied status is not available
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcldcClientRedirectUrl | 1.3.6.1.4.1.9.9.599.1.3.1.1.24 | CiscoURLStringOrEmpty | RO | | |||||||||||||||||
column · CiscoURLStringOrEmpty · read-only · current This object indicates the AAA override redirect URL for a
client with cldcClientPostureState enabled.
The object has a valid value when the WLAN, with which the
client has associated requires conditional or splash-page
or webauth web redirection.
This object is otherwise not applicable,
and contains a zero-length string.Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcldcClientAaaOverrideAclName | 1.3.6.1.4.1.9.9.599.1.3.1.1.25 | SnmpAdminString | RO | | |||||||||||||||||
column · SnmpAdminString · read-only · current This object indicates the AAA Override ACL Name for the client if cldcClientPostureState is enabled on the wlan. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcldcClientAaaOverrideAclApplied | 1.3.6.1.4.1.9.9.599.1.3.1.1.26 | INTEGER | RO | notAvailable(3) | |||||||||||||||||
column · INTEGER · read-only · current This object indicates the AAA Override ACL applied status for the client if cldcClientPostureState is enabled on the wlan. A value of 'true' indicates that the ACL is applied. A value of 'false' indicates that the ACL is not applied. A value of 'notAvailable' indicates that applied status is not available
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcldcClientUsername | 1.3.6.1.4.1.9.9.599.1.3.1.1.27 | SnmpAdminString (SIZE (0..32)) | RO | 0c23690fcdf8 | |||||||||||||||||
column · SnmpAdminString (SIZE (0..32)) · read-only · current This object represents the username used by the client. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcldcClientSSID | 1.3.6.1.4.1.9.9.599.1.3.1.1.28 | SnmpAdminString (SIZE (0..32)) | RO | SAP | |||||||||||||||||
column · SnmpAdminString (SIZE (0..32)) · read-only · current This object represents the SSID of the WLAN to which the client is associated. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcldcClientSecurityTagId | 1.3.6.1.4.1.9.9.599.1.3.1.1.29 | Unsigned32 | RO | ||||||||||||||||||
column · Unsigned32 · read-only · current This object represents the security group tag of the client. | |||||||||||||||||||||
| CcldcClientTypeKTS | 1.3.6.1.4.1.9.9.599.1.3.1.1.30 | TruthValue | RO | ||||||||||||||||||
column · TruthValue · read-only · current This object indicates whether the client is NEC KTS (National Electrical Code Key Telephone servie) client or not. A value of 'true' indicates that the client follows NEC KTS SIP protocol. A value of 'false' indicates that the client does not follow NEC KTS SIP protocol. | |||||||||||||||||||||
| CcldcClientIpv6AclName | 1.3.6.1.4.1.9.9.599.1.3.1.1.31 | SnmpAdminString | RO | ||||||||||||||||||
column · SnmpAdminString · read-only · current This object indicates the ACL name for the IPv6 client. An empty string denotes no ACL has been applied. | |||||||||||||||||||||
| CcldcClientIpv6AclApplied | 1.3.6.1.4.1.9.9.599.1.3.1.1.32 | INTEGER | RO | ||||||||||||||||||
column · INTEGER · read-only · current This object indicates the ACL applied status for the IPv6 client. A value of 'true' indicates that the ACL is applied. A value of 'false' indicates that the ACL is not applied. A value of 'notAvailable' indicates that applied status is not avaliable
| |||||||||||||||||||||
| CcldcClientDataSwitching | 1.3.6.1.4.1.9.9.599.1.3.1.1.33 | INTEGER | RO | central(2) | |||||||||||||||||
column · INTEGER · read-only · current This object indicates whether client is switching data locally or centrally. This object is valid for flexconnect APs. A value of 'unknown' indicates that client data switching is not known. A value of 'central' indicates that client data is tunneled to WLC using CAPWAP. A value of 'local' indicates that client data is bridged locally by AP.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcldcClientAuthentication | 1.3.6.1.4.1.9.9.599.1.3.1.1.34 | INTEGER | RO | central(2) | |||||||||||||||||
column · INTEGER · read-only · current This object indicates whether client is authentiated locally or centrally. This object is valid for flexconnect APs. A value of 'unknown' indicates that client authentication is not known. A value of 'central' indicates that client authenticatation is at WLC and AP tunnels client management traffic to WLC via CAPWAP. A value of 'local' indicates that client is authenticated locally by AP.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcldcClientChannel | 1.3.6.1.4.1.9.9.599.1.3.1.1.35 | Unsigned32 | RO | ||||||||||||||||||
column · Unsigned32 · read-only · current This object indicates the access point's channel to which the client is associated. | |||||||||||||||||||||
| CcldcClientAuthMode | 1.3.6.1.4.1.9.9.599.1.3.1.1.36 | INTEGER | RO | ||||||||||||||||||
column · INTEGER · read-only · current This object represents the authentication mode of client. A value of 'none' represents that client used open authentication to join to network. A value of 'psk' represents that client used PSK based authentication to join to network. A value of 'radius' represents that client gets authenticated with the help of radius. A value of 'cckm' represents that client used CCKM based authentication to join to network. A value of 'wapipsk' represents that client used WAPI PSK authentication to join to network. A value of 'wapicert' represents that client used WPA/WPA2 DOT1X authentication to join to network. A value of 'ftDot1x' represents that client used 802.11r DOT1X authentication to join to network. A value of 'ftpsk' represents that client used 802.11r PSK authentication to join to network. A value of 'pmfDot1x' represents that client used PMF DOT1X authentication to join to network. A value of 'pmfpsk' represents that client used PMF PSK authentication to join to network.
| |||||||||||||||||||||
| CcldcClientReasonCode | 1.3.6.1.4.1.9.9.599.1.3.1.1.37 | INTEGER | RO | ||||||||||||||||||
column · INTEGER · read-only · current This object represents the reason for disassociation of client. A value of 'unspecified' represents that client disassociated with reaon unspecified. A value of 'previousAuthNotValid' represents that client disassociated with reason previous authentication was not valid. A value of 'deauthenticationLeaving' represents that client disassociated with reason client leaving due to deauthentication. A value of 'disassociationDueToInactivity' represents that client disassociated with reason client disassociation due to inactivity. A value of 'disassociationAPBusy' represents that client disassociated with reason client disassociation since AP was busy. A value of 'class2FrameFromNonAuthStation' represents that client disassociated with reason class 2 frame from non authenticated station. A value of 'class2FrameFromNonAssStation' represents that client disassociated with reason class 2 frame from non associated station. A value of 'disassociationStaHasLeft' represents that client disassociated with reason station has left BSS due to disassociation. A value of 'staReqAssociationWithoutAuth' represents that client disassociated with reason station send association request without authentication. A value of 'invalidInformationElement' represents that client disassociated with reason stations send invalid information element in the management frame. A value of 'groupCipherInvalid' represents that client disassociated with reason invalid group cipher. A value of 'unicastCipherInvalid' represents that client disassociated with reason invalid unicast cipher. A value of 'akmpInvalid' represents that client disassociated with reason invalid key management protocol. A value of 'unsupportedRsnVersion' represents that client disassociated with reason unsupported RSN version. A value of 'invalidRsnIeCapabilities' represents that client disassociated with reason invalid RSN IE capabilities in the (re-)association request. A value of 'cipherSuiteRejected' represents that client disassociated with reason cipher suite rejected. A value of 'missingReasonCode' represents that client disassociated with reason reason code is missing. A value of 'maxAssociatedClientsReached' represents that client disassociated with reason maximum allowed associated client number has reached. A value of 'maxAssociatedClientsReachedOnRadio' represents that client disassociated with reason maximum allowed associated client number has reached on radio. A value of 'maxAssociatedClientsReachedOnWlan' represents that client disassociated with reason maximum allowed associated client number has reached on wlan. A value of 'unSpecifiedQosFailure' represents that client disassociated with reason unsupported QOS failure. A value of 'qosPolicyMismatch' represents that client disassociated with reason mismatch on QOS policy. A value of 'inSufficientBandwidth' represents that client disassociated with reason insufficient bandwidth to accommodate this station. A value of 'inValidQosParams' represents that client disassociated with reason invalid QOS parameters.
| |||||||||||||||||||||
| CcldcClientSessionID | 1.3.6.1.4.1.9.9.599.1.3.1.1.38 | SnmpAdminString | RO | ||||||||||||||||||
column · SnmpAdminString · read-only · current This object indicates the session to which the client is associated. | |||||||||||||||||||||
| CcldcClientApRoamMacAddress | 1.3.6.1.4.1.9.9.599.1.3.1.1.39 | MacAddress | RO | ||||||||||||||||||
column · MacAddress · read-only · current This object indicates the MAC address of the AP to which the client has roamed. | |||||||||||||||||||||
| CcldcClientMdnsProfile | 1.3.6.1.4.1.9.9.599.1.3.1.1.40 | SnmpAdminString | RO | ||||||||||||||||||
column · SnmpAdminString · read-only · current This object indicates the mDNS profile name mapped to 802.11 wireless client. It could be mapped to the WLAN to which the client is connected to, or the interface/interface groups mapped to the WLAN. | |||||||||||||||||||||
| CcldcClientMdnsAdvCount | 1.3.6.1.4.1.9.9.599.1.3.1.1.41 | Unsigned32 | RO | ||||||||||||||||||
column · Unsigned32 · read-only · current This object indicates the number of mDNS advertisements received on the client. | |||||||||||||||||||||
| CcldcClientPolicyName | 1.3.6.1.4.1.9.9.599.1.3.1.1.42 | SnmpAdminString | RO | ||||||||||||||||||
column · SnmpAdminString · read-only · current This object indicates the local classification policy applied on the client. | |||||||||||||||||||||
| CcldcClientAAARole | 1.3.6.1.4.1.9.9.599.1.3.1.1.43 | SnmpAdminString | RO | ||||||||||||||||||
column · SnmpAdminString · read-only · current This object indicates the role string of the client
that is used as match criterion for local policy
profiling. This value is provided by radius during
authentication. | |||||||||||||||||||||
| CcldcClientDeviceType | 1.3.6.1.4.1.9.9.599.1.3.1.1.44 | SnmpAdminString | RO | ||||||||||||||||||
column · SnmpAdminString · read-only · current This object indicates the device type of the client. This is identified once the profiling operation is completed. | |||||||||||||||||||||
| CcldcUserAuthType | 1.3.6.1.4.1.9.9.599.1.3.1.1.45 | INTEGER | RO | ||||||||||||||||||
column · INTEGER · read-only · current This object indicates the authentication aype of user. A value of 'open' indicates that the user authenticated using open security. A value of 'wepPsk' indicates that the user authenticated using WEP PSK security. A value of 'portal' indicates that the user authenticated using WEB layer3 portal security. A value of 'simPeap' indicates that the user authenticated using EAP SIM and PEAP security. A value of 'other' indicates that the user authenticated using security method not listed above.
| |||||||||||||||||||||
| CcldcClientTunnelType | 1.3.6.1.4.1.9.9.599.1.3.1.1.46 | INTEGER | RO | ||||||||||||||||||
column · INTEGER · read-only · current This object indicates the tunnel type used to send client traffic. A value of 'simple' indicates no tunnel is used to send client traffic towards DS. A value of 'pmipv6' indicates that PMIPv6 tunnel is used to send client traffic towards DS. A value of 'gtpv2' indicates that GTPv2 tunnel is used to send client traffic towards DS. A value of 'eogre' indicates that EOGRE tunnel is used to send client traffic towards DS.
| |||||||||||||||||||||
| CcldcClientMaxDataRate | 1.3.6.1.4.1.9.9.599.1.3.1.1.47 | Unsigned32 | RO | ||||||||||||||||||
column · Unsigned32 · read-only · current This object indicates the max data rate (Mbps) with which the client can operate. | |||||||||||||||||||||
| CcldcClientHtCapable | 1.3.6.1.4.1.9.9.599.1.3.1.1.48 | TruthValue | RO | ||||||||||||||||||
column · TruthValue · read-only · current This object indicates whether the client is HT (high throughput) capable or not. A value of 'true' indicates that client is HT capable. A value of 'false' indicates that client is not HT capable. | |||||||||||||||||||||
| CcldcClientVhtCapable | 1.3.6.1.4.1.9.9.599.1.3.1.1.49 | TruthValue | RO | ||||||||||||||||||
column · TruthValue · read-only · current This object indicates whether the client is VHT (very high throughput) capable or not. A value of 'true' indicates that client is VHT capable. A value of 'false' indicates that client is not VHT capable. | |||||||||||||||||||||
| CcldcClientCurrentTxRate | 1.3.6.1.4.1.9.9.599.1.3.1.1.50 | Unsigned32 | RO | ||||||||||||||||||
column · Unsigned32 · read-only · current This object represents the current data rate at which the client transmits and receives data. This provides the data rate value equivalent to the MCS value displayed in cldcClientCurrentTxRateSet.
| |||||||||||||||||||||
| CcldcClientiPSKTag | 1.3.6.1.4.1.9.9.599.1.3.1.1.51 | OCTET STRING | RO | | |||||||||||||||||
column · OCTET STRING · read-only · current This object indicates the PSK peer group that this client is part of. The clients with same psk tag can be allowed to have peer to peer traffic by configuring the wlan p2p blocking. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcldcClientMobileStPolicyType | 1.3.6.1.4.1.9.9.599.1.3.1.1.52 | INTEGER | RO | wpa2(3) | |||||||||||||||||
column · INTEGER · read-only · current Security policy of the AP to which the Mobile Station is associated.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| TcldcClientByIpTable | 1.3.6.1.4.1.9.9.599.1.3.2 | NA | |||||||||||||||||||
table · not-accessible · current This table represents the 802.11 wireless clients that are associated with the APs that have joined this controller and are indexed by cldcClientByIpAddressType and cldcClientByIpAddress. An entry is created automatically by the controller when the client gets associated to the AP. An existing entry gets deleted when the association gets dropped. | |||||||||||||||||||||
| RcldcClientByIpEntry | 1.3.6.1.4.1.9.9.599.1.3.2.1 | NA | |||||||||||||||||||
row · not-accessible · current Each entry represents a conceptual row in this table and provides the information about the clients associated to the APs that have joined the controller. An entry is identified by the client's IP address. | |||||||||||||||||||||
| CcldcClientByIpAddressType | 1.3.6.1.4.1.9.9.599.1.3.2.1.2 | InetAddressType | NA | ||||||||||||||||||
column · InetAddressType · not-accessible · current This object represents the type of the Client's address made available through cldcClientByIpAddress. | |||||||||||||||||||||
| CcldcClientByIpAddress | 1.3.6.1.4.1.9.9.599.1.3.2.1.3 | InetAddress | NA | ||||||||||||||||||
column · InetAddress · not-accessible · current This object indicates the client IP address. | |||||||||||||||||||||
| CcldcClientByIpAddressDiscoverType | 1.3.6.1.4.1.9.9.599.1.3.2.1.4 | INTEGER | RO | dhcp(3) | |||||||||||||||||
column · INTEGER · read-only · current This object represents the discovery type of the client's address A value of 'invalid' indicates that the IP address discover type is unknown. A value of 'ndp' indicates that the client learnt IP address by neighbor discovery protocol A value of 'dhcp' indicates that the client learnt IP address via DHCP. A value of 'packet' indicates that the client learnt IP address via data packet addressing learning. A value of 'local' indicates that the client learnt IP address via address applied to local interface. A value of 'static' indicates that the client learnt IP address via address assigned statically.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcldcClientByIpAddressLastSeen | 1.3.6.1.4.1.9.9.599.1.3.2.1.5 | TimeStamp | RO | 52200 (0d 0h 8m 42s) | |||||||||||||||||
column · TimeStamp · read-only · current This object indicates the time when an address was last seen in reachable state. Example values from LibreNMS test devices
| |||||||||||||||||||||
| TcldcSleepingClientTable | 1.3.6.1.4.1.9.9.599.1.3.3 | NA | |||||||||||||||||||
table · not-accessible · current This table represents the information about sleeping clients | |||||||||||||||||||||
| RcldcSleepingClientEntry | 1.3.6.1.4.1.9.9.599.1.3.3.1 | NA | |||||||||||||||||||
row · not-accessible · current An entry containing the information about sleeping clients. | |||||||||||||||||||||
| CcldcSleepingClientMacAddress | 1.3.6.1.4.1.9.9.599.1.3.3.1.1 | MacAddress | NA | ||||||||||||||||||
column · MacAddress · not-accessible · current This object represents the MAC address of the sleeping client and uniquely identifies the entry. | |||||||||||||||||||||
| CcldcSleepingClientSsid | 1.3.6.1.4.1.9.9.599.1.3.3.1.2 | OCTET STRING | RO | ||||||||||||||||||
column · OCTET STRING · read-only · current This object represents the SSID of the WLAN to which the sleeping client is associated. | |||||||||||||||||||||
| CcldcSleepingClientUserName | 1.3.6.1.4.1.9.9.599.1.3.3.1.3 | SnmpAdminString | RO | ||||||||||||||||||
column · SnmpAdminString · read-only · current This object represents the username used by the sleeping client. | |||||||||||||||||||||
| CcldcSleepingClientRemainingTime | 1.3.6.1.4.1.9.9.599.1.3.3.1.4 | TimeInterval | RO | ||||||||||||||||||
column · TimeInterval · read-only · current This object indicates the remaining session time for the sleeping client to be in associated state.
| |||||||||||||||||||||
| CcldcSleepingClientRowStatus | 1.3.6.1.4.1.9.9.599.1.3.3.1.5 | RowStatus | RC | ||||||||||||||||||
column · RowStatus · read-create · current This object specifies the status column for this row and used to delete specific instances of row in the table. | |||||||||||||||||||||
| NcldcStatisticObjects | 1.3.6.1.4.1.9.9.599.1.4 | ||||||||||||||||||||
| TcldcClientStatisticTable | 1.3.6.1.4.1.9.9.599.1.4.1 | NA | |||||||||||||||||||
table · not-accessible · current This table represents statistics and status of the 802.11 wireless clients associated to the controller. | |||||||||||||||||||||
| RcldcClientStatisticEntry | 1.3.6.1.4.1.9.9.599.1.4.1.1 | NA | |||||||||||||||||||
row · not-accessible · current An entry in this table represents traffic statistics of the associated client.
| |||||||||||||||||||||
| CcldcClientDataRetries | 1.3.6.1.4.1.9.9.599.1.4.1.1.1 | Counter64 | RO | 429 | |||||||||||||||||
column · Counter64 · read-only · current This object indicates the number of attempts made by the client before transmitting the MSDU successfully.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcldcClientRtsRetries | 1.3.6.1.4.1.9.9.599.1.4.1.1.2 | Counter64 | RO | 0 | |||||||||||||||||
column · Counter64 · read-only · current This object indicates the number of times the client has attempted to send RTS packets before receiving CTS packets.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcldcClientDuplicatePackets | 1.3.6.1.4.1.9.9.599.1.4.1.1.3 | Counter64 | RO | 0 | |||||||||||||||||
column · Counter64 · read-only · current This object indicates the number of times a duplicate packet is received for the client.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcldcClientDecryptFailures | 1.3.6.1.4.1.9.9.599.1.4.1.1.4 | Counter64 | RO | 0 | |||||||||||||||||
column · Counter64 · read-only · current This object indicates the number of packets received from the client that failed to decrypt properly.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcldcClientMicErrors | 1.3.6.1.4.1.9.9.599.1.4.1.1.5 | Counter64 | RO | 0 | |||||||||||||||||
column · Counter64 · read-only · current This object indicates the number of MIC errors experienced by the client.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcldcClientMicMissingFrames | 1.3.6.1.4.1.9.9.599.1.4.1.1.6 | Counter64 | RO | 0 | |||||||||||||||||
column · Counter64 · read-only · current This object indicates the number of missing MIC packets for the client.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CcldcClientRaPacketsDropped | 1.3.6.1.4.1.9.9.599.1.4.1.1.7 | Counter64 | RO | ||||||||||||||||||
column · Counter64 · read-only · current This object indicates the number of RA (router advertisements) packets dropped for this client. It's applicable for IPv6 clients only. | |||||||||||||||||||||
| CcldcClientInterimUpdatesCount | 1.3.6.1.4.1.9.9.599.1.4.1.1.8 | Counter64 | RO | ||||||||||||||||||
column · Counter64 · read-only · current This object indicates the number of interim updates sent for this client. | |||||||||||||||||||||
| CcldcClientDataBytesReceived | 1.3.6.1.4.1.9.9.599.1.4.1.1.9 | Counter64 | RO | ||||||||||||||||||
column · Counter64 · read-only · current This object indicates the number of data bytes received for this client | |||||||||||||||||||||
| CcldcClientRealtimeBytesReceived | 1.3.6.1.4.1.9.9.599.1.4.1.1.10 | Counter64 | RO | ||||||||||||||||||
column · Counter64 · read-only · current This object indicates the number of realtime bytes received for this mobile station | |||||||||||||||||||||
| CcldcClientRxDataBytesDropped | 1.3.6.1.4.1.9.9.599.1.4.1.1.11 | Counter64 | RO | ||||||||||||||||||
column · Counter64 · read-only · current This object indicates the number of received data bytes dropped for this mobile station | |||||||||||||||||||||
| CcldcClientRxRealtimeBytesDropped | 1.3.6.1.4.1.9.9.599.1.4.1.1.12 | Counter64 | RO | ||||||||||||||||||
column · Counter64 · read-only · current This object indicates the number of received realtime bytes dropped for this mobile station | |||||||||||||||||||||
| CcldcClientDataBytesSent | 1.3.6.1.4.1.9.9.599.1.4.1.1.13 | Counter64 | RO | ||||||||||||||||||
column · Counter64 · read-only · current This object indicates the number of data bytes sent for this mobile station | |||||||||||||||||||||
| CcldcClientRealtimeBytesSent | 1.3.6.1.4.1.9.9.599.1.4.1.1.14 | Counter64 | RO | ||||||||||||||||||
column · Counter64 · read-only · current This object indicates the number of realtime bytes sent for this mobile station | |||||||||||||||||||||
| CcldcClientTxDataBytesDropped | 1.3.6.1.4.1.9.9.599.1.4.1.1.15 | Counter64 | RO | ||||||||||||||||||
column · Counter64 · read-only · current This object indicates the number of transmitted data bytes dropped for this mobile station | |||||||||||||||||||||
| CcldcClientTxRealtimeBytesDropped | 1.3.6.1.4.1.9.9.599.1.4.1.1.16 | Counter64 | RO | ||||||||||||||||||
column · Counter64 · read-only · current This object indicates the number of transmitted realtime bytes dropped for this mobile station | |||||||||||||||||||||
| CcldcClientDataPacketsReceived | 1.3.6.1.4.1.9.9.599.1.4.1.1.17 | Counter64 | RO | ||||||||||||||||||
column · Counter64 · read-only · current This object indicates the number of data packets received for this mobile station | |||||||||||||||||||||
| CcldcClientRealtimePacketsReceived | 1.3.6.1.4.1.9.9.599.1.4.1.1.18 | Counter64 | RO | ||||||||||||||||||
column · Counter64 · read-only · current This object indicates the number realtime packets received for this mobile station | |||||||||||||||||||||
| CcldcClientRxDataPacketsDropped | 1.3.6.1.4.1.9.9.599.1.4.1.1.19 | Counter64 | RO | ||||||||||||||||||
column · Counter64 · read-only · current This object indicates the number of received data packets dropped for this mobile station | |||||||||||||||||||||
| CcldcClientRxRealtimePacketsDropped | 1.3.6.1.4.1.9.9.599.1.4.1.1.20 | Counter64 | RO | ||||||||||||||||||
column · Counter64 · read-only · current This object indicates the number of received realtime packets dropped for this mobile station | |||||||||||||||||||||
| CcldcClientDataPacketsSent | 1.3.6.1.4.1.9.9.599.1.4.1.1.21 | Counter64 | RO | ||||||||||||||||||
column · Counter64 · read-only · current This object indicates the number of data packets sent for this mobile station | |||||||||||||||||||||
| CcldcClientRealtimePacketsSent | 1.3.6.1.4.1.9.9.599.1.4.1.1.22 | Counter64 | RO | ||||||||||||||||||
column · Counter64 · read-only · current This object indicates the number of realtime packets sent for this mobile station | |||||||||||||||||||||
| CcldcClientTxDataPacketsDropped | 1.3.6.1.4.1.9.9.599.1.4.1.1.23 | Counter64 | RO | ||||||||||||||||||
column · Counter64 · read-only · current This object indicates the number of transmitted data packets dropped for this mobile station | |||||||||||||||||||||
| CcldcClientTxRealtimePacketsDropped | 1.3.6.1.4.1.9.9.599.1.4.1.1.24 | Counter64 | RO | ||||||||||||||||||
column · Counter64 · read-only · current This object indicates the number of transmitted realtime packets dropped for this mobile station | |||||||||||||||||||||
| CcldcClientTxDataPackets | 1.3.6.1.4.1.9.9.599.1.4.1.1.25 | Counter64 | RO | ||||||||||||||||||
column · Counter64 · read-only · current This object indicates the number of data packets sent by this mobile station | |||||||||||||||||||||
| CcldcClientTxDataBytes | 1.3.6.1.4.1.9.9.599.1.4.1.1.26 | Counter64 | RO | ||||||||||||||||||
column · Counter64 · read-only · current This object indicates the number of data bytes sent by this mobile station | |||||||||||||||||||||
| CcldcClientRxDataPackets | 1.3.6.1.4.1.9.9.599.1.4.1.1.27 | Counter64 | RO | ||||||||||||||||||
column · Counter64 · read-only · current This object indicates the number of data packets sent for this mobile station | |||||||||||||||||||||
| CcldcClientRxDataBytes | 1.3.6.1.4.1.9.9.599.1.4.1.1.28 | Counter64 | RO | ||||||||||||||||||
column · Counter64 · read-only · current This object indicates the number of data bytes sent for this mobile station | |||||||||||||||||||||
| NciscoLwappDot11ClientMIBConform | 1.3.6.1.4.1.9.9.599.2 | ||||||||||||||||||||
| NciscoLwappDot11ClientMIBCompliances | 1.3.6.1.4.1.9.9.599.2.1 | ||||||||||||||||||||
| MciscoLwappDot11ClientMIBCompliance | 1.3.6.1.4.1.9.9.599.2.1.1 | deprecated | |||||||||||||||||||
compliance · deprecated The compliance statement for the SNMP entities that implement this MIB. | |||||||||||||||||||||
| MciscoLwappDot11ClientMIBComplianceRev2 | 1.3.6.1.4.1.9.9.599.2.1.2 | deprecated | |||||||||||||||||||
compliance · deprecated The compliance statement for the SNMP entities that implement this MIB. | |||||||||||||||||||||
| MciscoLwappDot11ClientMIBComplianceRev3 | 1.3.6.1.4.1.9.9.599.2.1.3 | deprecated | |||||||||||||||||||
compliance · deprecated The compliance statement for the SNMP entities that implement this MIB.
| |||||||||||||||||||||
| MciscoLwappDot11ClientMIBComplianceRev4 | 1.3.6.1.4.1.9.9.599.2.1.4 | deprecated | |||||||||||||||||||
compliance · deprecated The compliance statement for the SNMP entities that implement this MIB.
| |||||||||||||||||||||
| MciscoLwappDot11ClientMIBComplianceRev5 | 1.3.6.1.4.1.9.9.599.2.1.5 | ||||||||||||||||||||
compliance · current The compliance statement for the SNMP entities that implement this MIB.
| |||||||||||||||||||||
| NciscoLwappDot11ClientMIBGroups | 1.3.6.1.4.1.9.9.599.2.2 | ||||||||||||||||||||
| GciscoLwappDot11ClientMIBConfigGroup | 1.3.6.1.4.1.9.9.599.2.2.1 | ||||||||||||||||||||
group · current This collection of objects specifies the required configuration parameters for the 802.11 wireless clients.
| |||||||||||||||||||||
| GciscoLwappDot11ClientMIBNotifsGroup | 1.3.6.1.4.1.9.9.599.2.2.2 | ||||||||||||||||||||
group · current This collection of objects specifies the notifications for the 802.11 wireless clients. | |||||||||||||||||||||
| GciscoLwappDot11ClientMIBStatusGroup | 1.3.6.1.4.1.9.9.599.2.2.3 | ||||||||||||||||||||
group · current This collection of objects specifies the required status parameters for the 802.11 wireless clients.
| |||||||||||||||||||||
| GciscoLwappDot11ClientMIBStatusGroupRev2 | 1.3.6.1.4.1.9.9.599.2.2.4 | ||||||||||||||||||||
group · current This collection of objects specifies the required status parameters for the 802.11 wireless clients.
| |||||||||||||||||||||
| GciscoLwappDot11ClientMIBNotifsGroupRev2 | 1.3.6.1.4.1.9.9.599.2.2.5 | ||||||||||||||||||||
group · current This collection of objects represents the notifications for the 802.11 wireless clients.
| |||||||||||||||||||||
| GciscoLwappDot11ClientMIBNotifControlGroup | 1.3.6.1.4.1.9.9.599.2.2.6 | ||||||||||||||||||||
group · current This collection of objects represents the objects that control the notifications for the 802.11 wireless clients. | |||||||||||||||||||||
| GciscoLwappDot11ClientMIBStatusGroupRev2Sup | 1.3.6.1.4.1.9.9.599.2.2.7 | ||||||||||||||||||||
group · current This collection of objects specifies the required status parameters for the 802.11 wireless clients and it supplements ciscoLwappDot11ClientMIBStatusGroupRev2. | |||||||||||||||||||||
| GciscoLwappDot11ClientMIBCcxGroup | 1.3.6.1.4.1.9.9.599.2.2.8 | ||||||||||||||||||||
group · current This collection of objects provides the 802.11 wireless CCX clients information. | |||||||||||||||||||||
| GciscoLwappDot11ClientMIBSup1Group | 1.3.6.1.4.1.9.9.599.2.2.9 | ||||||||||||||||||||
group · current This collection of objects provides the 802.11 wireless clients notifications information.
| |||||||||||||||||||||
| GciscoLwappDot11ClientMIBConfigGroupRev2 | 1.3.6.1.4.1.9.9.599.2.2.10 | ||||||||||||||||||||
group · current This collection of objects specifies the required configuration parameters for the 802.11 wireless clients. | |||||||||||||||||||||
| GciscoLwappDot11ClientMIBNotifsGroupRev3 | 1.3.6.1.4.1.9.9.599.2.2.11 | ||||||||||||||||||||
group · current This collection of objects represents the notifications for the 802.11 wireless clients. | |||||||||||||||||||||
| GciscoLwappDot11ClientMIBNotifControlGroupRev2 | 1.3.6.1.4.1.9.9.599.2.2.12 | ||||||||||||||||||||
group · current This collection of objects represents the objects that control the notifications for the 802.11 wireless clients.
| |||||||||||||||||||||
| GciscoLwappDot11ClientMIBStatusGroupRev3 | 1.3.6.1.4.1.9.9.599.2.2.13 | ||||||||||||||||||||
group · current This collection of objects specifies the required status parameters for the 802.11 wireless clients. | |||||||||||||||||||||
| NciscoLwappDot11CCXClientMIBConform | 1.3.6.1.4.1.9.9.599.2.3 | ||||||||||||||||||||
| NciscoLwappDot11ClientCCXV5ReportingMIBConform | 1.3.6.1.4.1.9.9.599.2.4 | ||||||||||||||||||||
| NciscoLwappDot11ClientCcxMIBObjects | 1.3.6.1.4.1.9.9.599.3 | ||||||||||||||||||||
| NcldcCcxObjects | 1.3.6.1.4.1.9.9.599.3.1 | ||||||||||||||||||||
| TcldccCcxVersionInfoTable | 1.3.6.1.4.1.9.9.599.3.1.1 | NA | |||||||||||||||||||
table · not-accessible · current This table represents the detail of the CCX version supported by the clients. This is used to identify the services supported by a CCX v6 client. | |||||||||||||||||||||
| RcldccCcxVersionInfoEntry | 1.3.6.1.4.1.9.9.599.3.1.1.1 | NA | |||||||||||||||||||
row · not-accessible · current There is an entry in the table for each entry identified by the client mac address. An entry is added when a CCX v6 client associates to the controller and existing entry gets deleted when the client disassociates from the controller.
| |||||||||||||||||||||
| CcldccCcxFoundationServiceVersion | 1.3.6.1.4.1.9.9.599.3.1.1.1.1 | CcxServiceVersion | RO | ||||||||||||||||||
column · CcxServiceVersion · read-only · current This object indicates the CCX version supported by the client for the foundation service. | |||||||||||||||||||||
| CcldccCcxLocationServiceVersion | 1.3.6.1.4.1.9.9.599.3.1.1.1.2 | CcxServiceVersion | RO | ||||||||||||||||||
column · CcxServiceVersion · read-only · current This object indicates the CCX version supported by the client for the location service. | |||||||||||||||||||||
| CcldccCcxVoiceServiceVersion | 1.3.6.1.4.1.9.9.599.3.1.1.1.3 | CcxServiceVersion | RO | ||||||||||||||||||
column · CcxServiceVersion · read-only · current This object indicates the CCX version supported by the client for the voice service. | |||||||||||||||||||||
| CcldccCcxManagementServiceVersion | 1.3.6.1.4.1.9.9.599.3.1.1.1.4 | CcxServiceVersion | RO | ||||||||||||||||||
column · CcxServiceVersion · read-only · current This object indicates the CCX version supported by the client for the management service. | |||||||||||||||||||||
Traps / Notifications
- ciscoLwappDot11ClientAssocDataStatsTrap
1.3.6.1.4.1.9.9.599.0.7 - ciscoLwappDot11ClientAssocNacAlert
1.3.6.1.4.1.9.9.599.0.2 - ciscoLwappDot11ClientAssocTrap
1.3.6.1.4.1.9.9.599.0.9 - ciscoLwappDot11ClientDeAuthenticatedTrap
1.3.6.1.4.1.9.9.599.0.10 - ciscoLwappDot11ClientDisassocDataStatsTrap
1.3.6.1.4.1.9.9.599.0.6 - ciscoLwappDot11ClientDisassocNacAlert
1.3.6.1.4.1.9.9.599.0.3 - ciscoLwappDot11ClientKeyDecryptError
1.3.6.1.4.1.9.9.599.0.1 - ciscoLwappDot11ClientMaxClientsReached
1.3.6.1.4.1.9.9.599.0.13 - ciscoLwappDot11ClientMobilityTrap
1.3.6.1.4.1.9.9.599.0.12 - ciscoLwappDot11ClientMovedToRunState
1.3.6.1.4.1.9.9.599.0.4 - ciscoLwappDot11ClientMovedToRunStateNewTrap
1.3.6.1.4.1.9.9.599.0.11 - ciscoLwappDot11ClientSessionTrap
1.3.6.1.4.1.9.9.599.0.8 - ciscoLwappDot11ClientStaticIpFailTrap
1.3.6.1.4.1.9.9.599.0.5
Groups and compliance
- ciscoLwappDot11ClientMIBCcxGroup
- ciscoLwappDot11ClientMIBCompliance
- ciscoLwappDot11ClientMIBComplianceRev2
- ciscoLwappDot11ClientMIBComplianceRev3
- ciscoLwappDot11ClientMIBComplianceRev4
- ciscoLwappDot11ClientMIBComplianceRev5
- ciscoLwappDot11ClientMIBConfigGroup
- ciscoLwappDot11ClientMIBConfigGroupRev2
- ciscoLwappDot11ClientMIBNotifControlGroup
- ciscoLwappDot11ClientMIBNotifControlGroupRev2
- ciscoLwappDot11ClientMIBNotifsGroup
- ciscoLwappDot11ClientMIBNotifsGroupRev2
- ciscoLwappDot11ClientMIBNotifsGroupRev3
- ciscoLwappDot11ClientMIBStatusGroup
- ciscoLwappDot11ClientMIBStatusGroupRev2
- ciscoLwappDot11ClientMIBStatusGroupRev2Sup
- ciscoLwappDot11ClientMIBStatusGroupRev3
- ciscoLwappDot11ClientMIBSup1Group