CISCO-GNSS-MIB
ciscoSystemsThe MIB module for GNSS Overview of GNSS GNSS (Global Navigation Satellite System) is used to describe the collection of Satellite Systems that are operating or planned. There are many Satellite constellation systems already available. These constellations allows ground base GNSS receivers to receive radio signals from these satellites and recover accurate location and time. Location and Time both are primary uses cases for many technologies, specifically for Telecom Network Operator, Timing use case is very important. Typical telecom networks synchronization works in a hierarchal manner where core network is connected to stratum 1 clock and the clock is distributed along the network in a tree like structure. With GPS receiver however, clocking can be changed to a flat architecture where access networks can directly take clock from satellites in sky using on-board GPS chips. MIB description This MIB is to support the GNSS feature of Cisco System devices. The below table specifies the object formats of the various textual conventions used. Data type mapping Textual Convention SYNTAX -------------------- ------------------ --------------------- RP state on slot SlotState OCTET UINT(SIZE(0..1)) RP Slot number SlotInfo OCTET UINT(SIZE(0..1)) GNSS module lock GnssModuleLockStatus OCTET INTEGER(1..2) GNSS module presens GnssModulePresenceStatus INTEGER(1..2)
snmptranslate -m CISCO-GNSS-MIB -Tpsnmpwalk -v2c -c <community> -m CISCO-GNSS-MIB <host> 1.3.6.1.4.1.9.9.862Imports
| CISCO-SMI | ciscoMgmt |
|---|---|
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP |
| SNMPv2-SMI | Bits, Counter32, Integer32, IpAddress, MODULE-IDENTITY, MibIdentifier, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, iso |
| SNMPv2-TC | DisplayString, PhysAddress, TEXTUAL-CONVENTION |
OID tree
| Name | OID | Type | Access | Status | Example | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| IciscoGnssMIB | 1.3.6.1.4.1.9.9.862 | ||||||||||||
identity The MIB module for GNSS Overview of GNSS GNSS (Global Navigation Satellite System) is used to describe the collection of Satellite Systems that are operating or planned. There are many Satellite constellation systems already available. These constellations allows ground base GNSS receivers to receive radio signals from these satellites and recover accurate location and time. Location and Time both are primary uses cases for many technologies, specifically for Telecom Network Operator, Timing use case is very important. Typical telecom networks synchronization works in a hierarchal manner where core network is connected to stratum 1 clock and the clock is distributed along the network in a tree like structure. With GPS receiver however, clocking can be changed to a flat architecture where access networks can directly take clock from satellites in sky using on-board GPS chips. MIB description This MIB is to support the GNSS feature of Cisco System devices. The below table specifies the object formats of the various textual conventions used. Data type mapping Textual Convention SYNTAX -------------------- ------------------ --------------------- RP state on slot SlotState OCTET UINT(SIZE(0..1)) RP Slot number SlotInfo OCTET UINT(SIZE(0..1)) GNSS module lock GnssModuleLockStatus OCTET INTEGER(1..2) GNSS module presens GnssModulePresenceStatus INTEGER(1..2) | |||||||||||||
| NciscoGnssMIBNotifs | 1.3.6.1.4.1.9.9.862.0 | ||||||||||||
| !ciscoGnssModuleLockStatus | 1.3.6.1.4.1.9.9.862.0.1 | ||||||||||||
notification · current Notifiation generated when the GNSS module lock status turn to Down state. | |||||||||||||
| !ciscoGnssModuleLockClear | 1.3.6.1.4.1.9.9.862.0.2 | ||||||||||||
notification · current Notifiation generated when the GNSS module lock status turn to Up state. | |||||||||||||
| !ciscoGnssModulePresenceStatus | 1.3.6.1.4.1.9.9.862.0.3 | ||||||||||||
notification · current Notification generated when the GNSS module is removed. | |||||||||||||
| !ciscoGnssModulePresenceClear | 1.3.6.1.4.1.9.9.862.0.4 | ||||||||||||
notification · current Notification generated when the GNSS module is powered up. | |||||||||||||
| !ciscoGnssAntennaSCAlarmStatus | 1.3.6.1.4.1.9.9.862.0.5 | ||||||||||||
notification · current Notification generated when the GNSS antenna detect short-circuit alarm | |||||||||||||
| !ciscoGnssAntennaSCAlarmClear | 1.3.6.1.4.1.9.9.862.0.6 | ||||||||||||
notification · current Notification generated when the GNSS antenna short-circuit alarm is cleared | |||||||||||||
| !ciscoGnssAntennaOCAlarmStatus | 1.3.6.1.4.1.9.9.862.0.7 | ||||||||||||
notification · current Notification generated when the GNSS antenna detect open-circuit alarm | |||||||||||||
| !ciscoGnssAntennaOCAlarmClear | 1.3.6.1.4.1.9.9.862.0.8 | ||||||||||||
notification · current Notification generated when the GNSS antenna open-circuit alarm is cleared | |||||||||||||
| !ciscoGnssSatelliteVisibilityStatus | 1.3.6.1.4.1.9.9.862.0.9 | ||||||||||||
notification · current Notification generated when there are < 3 satellites visible with < 30 dBM SNS | |||||||||||||
| !ciscoGnssSatelliteVisibilityClear | 1.3.6.1.4.1.9.9.862.0.10 | ||||||||||||
notification · current Notification generated when there are > 3 satellites visible with > 30 dBM SNS | |||||||||||||
| NciscoGnssMIBObjects | 1.3.6.1.4.1.9.9.862.1 | ||||||||||||
| ScGnssModuleLockStatus | 1.3.6.1.4.1.9.9.862.1.1 | GnssModuleLockStatus | RO | 2 | |||||||||
scalar · GnssModuleLockStatus · read-only · current This object specifies GNSS module lock status Example values from LibreNMS test devices
| |||||||||||||
| ScGnssModulePresenceStatus | 1.3.6.1.4.1.9.9.862.1.2 | GnssModulePresenceStatus | RO | ||||||||||
scalar · GnssModulePresenceStatus · read-only · current This object specifies GNSS module presence status | |||||||||||||
| ScGnssModuleSlotInfo | 1.3.6.1.4.1.9.9.862.1.3 | SlotInfo | RO | ||||||||||
scalar · SlotInfo · read-only · current This object specifies slot information where the GNSS module is inserted | |||||||||||||
| ScGnssModuleSlotState | 1.3.6.1.4.1.9.9.862.1.4 | SlotState | RO | ||||||||||
scalar · SlotState · read-only · current This object specifies state of the RSP (active/standby) where the GNSS module is inserted. | |||||||||||||
| ScGnssSatelliteVisibilityStatus | 1.3.6.1.4.1.9.9.862.1.5 | GnssSvVisibilityStatus | RO | 2 | |||||||||
scalar · GnssSvVisibilityStatus · read-only · current This object specifies status of the GNSS (good/bad), If tracking minimum 3 satellites with more than 30dBM then good, if not bad. Example values from LibreNMS test devices
| |||||||||||||
| ScGnssModuleSatelliteCount | 1.3.6.1.4.1.9.9.862.1.6 | SVCnt | RO | 13 | |||||||||
scalar · SVCnt · read-only · current This object specifies the count of satellite tracked by GNSS module Example values from LibreNMS test devices
| |||||||||||||
| ScGnssModuleSvIdSNR | 1.3.6.1.4.1.9.9.862.1.7 | DisplayString | RO | ||||||||||
scalar · DisplayString · read-only · current This object specifies the SNR value and satellite id for each visible satellite. | |||||||||||||
| ScGnssModuleSCAlarmStatus | 1.3.6.1.4.1.9.9.862.1.8 | ShortCircuitAlarmStatus | RO | 2 | |||||||||
scalar · ShortCircuitAlarmStatus · read-only · current This object specifies GNSS module short-circuit alarm status Example values from LibreNMS test devices
| |||||||||||||
| ScGnssModuleOCAlarmStatus | 1.3.6.1.4.1.9.9.862.1.9 | OpenCircuitAlarmStatus | RO | 2 | |||||||||
scalar · OpenCircuitAlarmStatus · read-only · current This object specifies GNSS module open-circuit alarm status Example values from LibreNMS test devices
| |||||||||||||
| NciscoGnssMIBConform | 1.3.6.1.4.1.9.9.862.2 | ||||||||||||
| NciscoGnssMIBCompliances | 1.3.6.1.4.1.9.9.862.2.1 | ||||||||||||
| MciscoGnssMIBCompliance | 1.3.6.1.4.1.9.9.862.2.1.1 | ||||||||||||
compliance · current This is a default module-compliance containing default object groups. | |||||||||||||
| NciscoGnssMIBGroups | 1.3.6.1.4.1.9.9.862.2.2 | ||||||||||||
| GciscoGnssMIBMainObjectGroup | 1.3.6.1.4.1.9.9.862.2.2.1 | ||||||||||||
| GciscoGnssMIBNotificationGroup | 1.3.6.1.4.1.9.9.862.2.2.2 | ||||||||||||
Textual conventions
GnssModuleLockStatusINTEGERdown(1)up(2)It is used as the Lock status identifier of the GNSS module. Notification generated upon the change detected in GNSS modulelock status GNSS Lockstatus Value -------------------------------- Down 1 Up 2
GnssModulePresenceStatusINTEGERabsent(1)present(2)Identifier to indicate the presence of the GNSS module on the router. Notification generated upon GNSS module insertion and removal GNSS Module Value -------------------------------- Absent 1 Present 2
GnssSvVisibilityStatusINTEGERbad(1)good(2)GNSS Status (good/bad), If tracking minimum 3 satellites with more than 30dBM then good, if not bad. When < 3 satellites (with >= 30 dBM) are available: GNSS Status is sent as BAD. When > 3 satellites (with >= 30 dBM) are available: GNSS Status is sent as GOOD.
OpenCircuitAlarmStatusINTEGERclear(2)raise(1)It is used as the open-ciruit alarm status identifier of the GNSS module. Notification generated upon the the open-circuit alarm raised or cleared status Open-circuit status Value -------------------------------- Raise 1 Clear 2
SVCntInteger32Number of satellite tracked by GNSS.
ShortCircuitAlarmStatusINTEGERclear(2)raise(1)It is used as the short-ciruit alarm status identifier of the GNSS module. Notification generated upon the the short-circuit alarm raised or cleared status Short-circuit status Value -------------------------------- Raise 1 Clear 2
SlotInfoUnsigned32 (0..1)RSP slot number of the node where the GNSS module is inserted. It can be Slot-0 or Slot-1
SlotStateUnsigned32 (0..1)State of the RSP where the GNSS module is inserted. It can be 0-Active or 1-StandBy
Traps / Notifications
- ciscoGnssAntennaOCAlarmClear
1.3.6.1.4.1.9.9.862.0.8 - ciscoGnssAntennaOCAlarmStatus
1.3.6.1.4.1.9.9.862.0.7 - ciscoGnssAntennaSCAlarmClear
1.3.6.1.4.1.9.9.862.0.6 - ciscoGnssAntennaSCAlarmStatus
1.3.6.1.4.1.9.9.862.0.5 - ciscoGnssModuleLockClear
1.3.6.1.4.1.9.9.862.0.2 - ciscoGnssModuleLockStatus
1.3.6.1.4.1.9.9.862.0.1 - ciscoGnssModulePresenceClear
1.3.6.1.4.1.9.9.862.0.4 - ciscoGnssModulePresenceStatus
1.3.6.1.4.1.9.9.862.0.3 - ciscoGnssSatelliteVisibilityClear
1.3.6.1.4.1.9.9.862.0.10 - ciscoGnssSatelliteVisibilityStatus
1.3.6.1.4.1.9.9.862.0.9