CISCO-ERR-DISABLE-MIB
ciscoSystemsThis MIB module provides the ability for a Network
Management Station (NMS) to configure and monitor the
error-disable feature via SNMP.
The error-disable feature allows other software
features running in a system to operationally disable a
system entity upon detecting abnormal conditions.
Examples of such a system entity include interfaces, a
vlan configured in the system, or a VLAN allowed on
specific layer 2 multi-vlan interface.
More specific examples:
a) When BPDU guard is enabled on an interface
it is expected that no BPDU packets are received by
the interface. If a BPDU packet is received, then the
BPDU guard will operationally disable the
interface.
b) Users can configure a particular threshold of
broadcast packets received on an interface. If the
number of packets received exceeds the threshold, then
storm-control will disable the interface.
c) When unidirectional Link Detection (UDLD) detects a
unidirectional link on an interface, it can disable
the interface.
d) On a trunk or a multi-vlan layer 2 port, if
port-security detects violation on a particular vlan,
then it can operationally disable that vlan on that
port.
The definition of 'abnormal condition' is under the
control of features that make use of the error-disable
feature to disable system entities.
The error-disable feature supports the following
configuration:
1) Whether software features can in fact use the
error-disable feature upon detecting abnormal
conditions.
NOTE: Some software features will ALWAYS use the
error-disable feature to disable entities upon
detection of error.
2) Whether the system can attempt to automatically
recover after a system entity has been disabled (e.g.,
A system can attempt to bring up a physical interface
which had been disabled earlier)
3) If error recovery is possible, then the time
interval to wait before the system starts the recovery
attempt.snmptranslate -m CISCO-ERR-DISABLE-MIB -Tpsnmpwalk -v2c -c <community> -m CISCO-ERR-DISABLE-MIB <host> 1.3.6.1.4.1.9.9.548Imports
| CISCO-PRIVATE-VLAN-MIB | VlanIndexOrZero |
|---|---|
| CISCO-SMI | ciscoMgmt |
| CISCO-TC | TimeIntervalSec |
| IF-MIB | ifIndex |
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP |
| SNMPv2-SMI | Bits, Integer32, IpAddress, MODULE-IDENTITY, MibIdentifier, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, iso |
| SNMPv2-TC | DisplayString, PhysAddress, TEXTUAL-CONVENTION, TruthValue |
OID tree
| Name | OID | Type | Access | Status |
|---|---|---|---|---|
| IciscoErrDisableMIB | 1.3.6.1.4.1.9.9.548 | |||
identity This MIB module provides the ability for a Network
Management Station (NMS) to configure and monitor the
error-disable feature via SNMP.
The error-disable feature allows other software
features running in a system to operationally disable a
system entity upon detecting abnormal conditions.
Examples of such a system entity include interfaces, a
vlan configured in the system, or a VLAN allowed on
specific layer 2 multi-vlan interface.
More specific examples:
a) When BPDU guard is enabled on an interface
it is expected that no BPDU packets are received by
the interface. If a BPDU packet is received, then the
BPDU guard will operationally disable the
interface.
b) Users can configure a particular threshold of
broadcast packets received on an interface. If the
number of packets received exceeds the threshold, then
storm-control will disable the interface.
c) When unidirectional Link Detection (UDLD) detects a
unidirectional link on an interface, it can disable
the interface.
d) On a trunk or a multi-vlan layer 2 port, if
port-security detects violation on a particular vlan,
then it can operationally disable that vlan on that
port.
The definition of 'abnormal condition' is under the
control of features that make use of the error-disable
feature to disable system entities.
The error-disable feature supports the following
configuration:
1) Whether software features can in fact use the
error-disable feature upon detecting abnormal
conditions.
NOTE: Some software features will ALWAYS use the
error-disable feature to disable entities upon
detection of error.
2) Whether the system can attempt to automatically
recover after a system entity has been disabled (e.g.,
A system can attempt to bring up a physical interface
which had been disabled earlier)
3) If error recovery is possible, then the time
interval to wait before the system starts the recovery
attempt. | ||||
| NciscoErrDisableMIBNotifs | 1.3.6.1.4.1.9.9.548.0 | |||
| NcErrDisableNotificationsPrefix | 1.3.6.1.4.1.9.9.548.0.1 | |||
| !cErrDisableInterfaceEvent | 1.3.6.1.4.1.9.9.548.0.1.1 | deprecated | ||
notification · deprecated The cErrDisableInterfaceEvent is generated when an interface
or {interface, vlan} is error-disabled by the feature
specified in cErrDisableIfStatusCause.
cErrDisableInterfaceEvent is deprecated and replaced by
cErrDisableInterfaceEventRev1.
| ||||
| !cErrDisableInterfaceEventRev1 | 1.3.6.1.4.1.9.9.548.0.2 | |||
notification · current The cErrDisableInterfaceEventRev1 is generated when an
interface or {interface, vlan} is error-disabled by the
feature specified in cErrDisableIfStatusCause.
cErrDisableInterfaceEventRev1 deprecates
cErrDisableInterfaceEvent to make it RFC 2578 compliant.
According to section 8.5 of RFC 2578, the next
to last sub-identifier in the name of any newly-defined
notification must have the value zero.
| ||||
| NciscoErrDisableMIBObjects | 1.3.6.1.4.1.9.9.548.1 | |||
| NcErrDisableGlobalObjects | 1.3.6.1.4.1.9.9.548.1.1 | |||
| ScErrDisableRecoveryInterval | 1.3.6.1.4.1.9.9.548.1.1.1 | TimeIntervalSec | RW | |
scalar · TimeIntervalSec · read-write · current This object specifies the error-disable recovery time interval. When a system entity is operationally disabled upon detecting abnormal condition by a particular feature, the system waits for a period equal to this time interval, and then re-enable the entity if automatic recovery is enabled for the feature. | ||||
| ScErrDisableNotifEnable | 1.3.6.1.4.1.9.9.548.1.1.2 | TruthValue | RW | |
scalar · TruthValue · read-write · current This object specifies whether cErrDisableInterfaceEvent and cErrDisableInterfaceEventRev1 notifications should be generated when a system entity is error-disabled. | ||||
| ScErrDisableNotifRate | 1.3.6.1.4.1.9.9.548.1.1.3 | Unsigned32 | RW | |
scalar · Unsigned32 · read-write · current The value of this object specifies the maximum number of error-disable notifications the device will generate per minute. A value of '0' specifies no limit and the device will generate a notification for each error-disable event.
| ||||
| NcErrDisableFeatureObjects | 1.3.6.1.4.1.9.9.548.1.2 | |||
| TcErrDisableFeatureTable | 1.3.6.1.4.1.9.9.548.1.2.1 | NA | ||
table · not-accessible · current This table contains the error-disable related info for each feature employing the error-disable feature. | ||||
| RcErrDisableFeatureEntry | 1.3.6.1.4.1.9.9.548.1.2.1.1 | NA | ||
row · not-accessible · current An entry is created for each feature that employs the error-disable feature. | ||||
| CcErrDisableFeatureIndex | 1.3.6.1.4.1.9.9.548.1.2.1.1.1 | CErrDisableFeatureID | NA | |
column · CErrDisableFeatureID · not-accessible · current This object uniquely identifies a feature that makes use of the error-disable feature. | ||||
| CcErrDisableFeatureConfigurable | 1.3.6.1.4.1.9.9.548.1.2.1.1.2 | Bits | RO | |
column · Bits · read-only · current This object indicates whether the error-disable related
configuration is configurable for this feature. If a bit
is set to 1, then the corresponding error-disable
configuration can be configured.
'detectionEnable' - indicates the error-disable detection
can be enabled/disabled for this feature
via cErrDisableFeatureDetectEnable.
'recoveryEnable' - indicates the error-disable recovery
can be enabled/disabled for this feature
via cErrDisableFeatureRecoveryEnable.
'recoveryInterval' - indicates the error-disable recovery
Interval can be configured via
cErrDisableFeatureRecoveryInterval.
'detectShutdownVlan' - indicates the error-disable detection
shutdown vlan mode can be configured for
this feature via
cErrDisableFeatureDetectShutdownVlan.
'flapControl' - indicates the error-disable flap control
can be configured via
cErrDisableFeatureMaxFlapCount and
cErrDisableFeatureFlapTimePeriod.
| ||||
| CcErrDisableFeatureDetectEnable | 1.3.6.1.4.1.9.9.548.1.2.1.1.3 | TruthValue | RW | |
column · TruthValue · read-write · current This object specifies whether the error-disable detection is enabled for the feature. Note: This object is read-write only for those features that are configurable, meaning: cErrDisableFeatureConfigurable.<featureIndex> has the first bit set to 1. | ||||
| CcErrDisableFeatureRecoveryEnable | 1.3.6.1.4.1.9.9.548.1.2.1.1.4 | TruthValue | RW | |
column · TruthValue · read-write · current This object specifies whether the system can automatically recover a system entity that has been disabled by the feature. | ||||
| CcErrDisableFeatureRecoveryInterval | 1.3.6.1.4.1.9.9.548.1.2.1.1.5 | TimeIntervalSec | RW | |
column · TimeIntervalSec · read-write · current This object specifies the error-recovery time interval that will be used by the system for any system entity that is error-disabled by this particular feature. If the value of this object is '0', then the device will use the value specified by the global configuration object cErrDisableRecoveryInterval. | ||||
| CcErrDisableFeatureDetectShutdownVlan | 1.3.6.1.4.1.9.9.548.1.2.1.1.6 | TruthValue | RW | |
column · TruthValue · read-write · current This object specifies whether shutting down the violating VLAN on an interface is enabled or not. The value of 'true' indicates that shutting down the violating VLAN on an interface is enabled. The value of 'false' indicates that shutting down the violating VLAN on an interface is disabled. | ||||
| CcErrDisableFeatureMaxFlapCount | 1.3.6.1.4.1.9.9.548.1.2.1.1.7 | Unsigned32 | RW | |
column · Unsigned32 · read-write · current This object specifies the maximum number of flaps that are allowed to occur before setting to error disable state. A read-only value of zero indicates that no flap control is present. | ||||
| CcErrDisableFeatureFlapTimePeriod | 1.3.6.1.4.1.9.9.548.1.2.1.1.8 | Unsigned32 | RW | |
column · Unsigned32 · read-write · current This object specifies the period of time counting the number of flaps that are allowed before setting to error disable state. A read-only value of zero indicates that no flap control is present. | ||||
| NcErrDisableIfObjects | 1.3.6.1.4.1.9.9.548.1.3 | |||
| TcErrDisableIfStatusTable | 1.3.6.1.4.1.9.9.548.1.3.1 | NA | ||
table · not-accessible · current This table provides interface (port) specific
error-disable status information. Each conceptual row
provides status information about a {interface, vlan}
disabled by a feature.
On a trunk or multi-vlan access interface, a given vlan on
the interface can be error-disabled. In this case, the row is
indexed by the ifIndex for the interface and the vlan
index corresponding to the vlan in question.
If the interface is carrying only 1 vlan or the entire
trunk interface is error-disabled (due to link flaps, for
example) then the vlan index portion of the row index is
0. | ||||
| RcErrDisableIfStatusEntry | 1.3.6.1.4.1.9.9.548.1.3.1.1 | NA | ||
row · not-accessible · current A collection of objects that specify the status of an
error-disabled Interface or {interface, vlan}. | ||||
| CcErrDisableIfStatusVlanIndex | 1.3.6.1.4.1.9.9.548.1.3.1.1.1 | VlanIndexOrZero | NA | |
column · VlanIndexOrZero · not-accessible · current This object specifies the vlan of the given interface that has been error-disabled. If the physical interface is error-disabled then the value of this object is 0. | ||||
| CcErrDisableIfStatusCause | 1.3.6.1.4.1.9.9.548.1.3.1.1.2 | CErrDisableFeatureID | RO | |
column · CErrDisableFeatureID · read-only · current This object specifies the feature/event that caused the
{interface, vlan} (or the entire interface) to be
error-disabled. | ||||
| CcErrDisableIfStatusTimeToRecover | 1.3.6.1.4.1.9.9.548.1.3.1.1.3 | TimeIntervalSec | RO | |
column · TimeIntervalSec · read-only · current Time left before the system attempts an automatic recovery of the interface or the vlan of the given interface. If no recovery is scheduled, then the value of this object is '0'. | ||||
| NciscoErrDisableMIBConform | 1.3.6.1.4.1.9.9.548.2 | |||
| NciscoErrDisableMIBCompliances | 1.3.6.1.4.1.9.9.548.2.1 | |||
| MciscoErrDisableMIBCompliance | 1.3.6.1.4.1.9.9.548.2.1.1 | deprecated | ||
compliance · deprecated The compliance statement for the cisco errdisable MIB. | ||||
| MciscoErrDisableMIBComplianceRev1 | 1.3.6.1.4.1.9.9.548.2.1.2 | deprecated | ||
compliance · deprecated The compliance statement for the cisco errdisable MIB. | ||||
| MciscoErrDisableMIBComplianceRev2 | 1.3.6.1.4.1.9.9.548.2.1.3 | |||
compliance · current The compliance statement for the cisco errdisable MIB. | ||||
| NciscoErrDisableMIBGroups | 1.3.6.1.4.1.9.9.548.2.2 | |||
| GciscoErrDisableGlobalCfgGroup | 1.3.6.1.4.1.9.9.548.2.2.1 | |||
group · current A collection of objects to configure error-disable functionality.
| ||||
| GciscoErrDisableFeatureCfgGroup | 1.3.6.1.4.1.9.9.548.2.2.2 | |||
group · current A collection of objects to manage the configuration of the error-disable feature. | ||||
| GciscoErrDisableIfStatusGroup | 1.3.6.1.4.1.9.9.548.2.2.3 | |||
group · current A collection of error-disable interface status objects. | ||||
| GciscoErrDisableNotifCfgGroup | 1.3.6.1.4.1.9.9.548.2.2.4 | |||
group · current A collection of objects to configure error-disable notifications. | ||||
| GciscoErrDisableNotifGroup | 1.3.6.1.4.1.9.9.548.2.2.5 | deprecated | ||
group · deprecated A collection of error-disable notification objects.
| ||||
| GciscoErrDisableNotifGroupRev1 | 1.3.6.1.4.1.9.9.548.2.2.6 | |||
group · current A collection of error-disable notification objects. | ||||
| GciscoErrDisableShutdownVlanGroup | 1.3.6.1.4.1.9.9.548.2.2.7 | |||
group · current A collection of objects to manage the configuration of error-disable detection shutdown vlan mode. | ||||
| GciscoErrDisableFeatureFlapGroup | 1.3.6.1.4.1.9.9.548.2.2.8 | |||
group · current A collection of objects to manage the configuration of the error-disable flap control. | ||||
Textual conventions
CErrDisableFeatureIDINTEGERadminModeIncomp(40)adminRxBBCreditIncomp(42)adminRxBBCreditPerfBufIncomp(38)adminRxBufSizeIncomp(43)adminSpeedIncomp(41)arpInspection(16)bpduGuard(2)channelErrDisabled(53)channelMisconfig(3)communityLimit(25)dhcpRateLimit(11)dot1adIncompEtype(22)dot1adIncompTunnel(23)dot1xSecurityViolation(8)dtpFlap(5)ekey(28)eppFailure(44)excessivePortInterrupts(52)ficonNotEnabled(39)gbicInvalid(10)hwProgFailed(54)inlinePower(15)internalHandshakeFailed(55)invalidPolicy(26)ipConflict(58)ipQosCompatCheckFailure(61)l2ptGuard(7)linkFlap(6)linkMonitorFailure(20)loopDetect(62)lsGroup(27)macLimit(19)multipleMSapIdsRcvd(59)mvrp(34)oamRemoteCriticalEvent(31)oamRemoteDyingGasp(32)oamRemoteFailure(21)oamRemoteLinkFault(33)oneHundredPdusWithoutAck(60)osmEPortUp(45)osmNonEPortUp(46)other(36)packetBuffer(18)pagpFlap(4)portLoopback(17)portModeFailure(29)portReinitLimitReached(37)portSecurityViolation(9)pppoeIaRateLimit(30)sfpConfigMismatch(24)stormControl(14)stpInconsistencyOnVpcPeerLink(56)stpPortStateFailure(57)tranceiverIncomp(35)udld(1)udldAggrasiveModeLinkFailed(51)udldEmptyEcho(50)udldNeighbourMismatch(49)udldTxRxLoop(48)udldUniDir(47)unicastFlood(12)vmps(13)An integer-value assigned to various features/events that can error disable a system entity udld: Unidirectional Link Detection bpduGuard: Spanning Tree BPDU Guard feature that prevents processing BPDU packets on an access interface channelMisconfig: General Link Aggregation mis-configuration pagpFlap: Cisco's PAGP Link Aggregation protocol errors dtpFlap: Dynamic Trunking Protocol errors linkFlap: Link State flapping l2ptGuard: L2 Protocol Tunnel errors dot1xSecurityViolation: 802.1x authentication violations portSecurity: Port Security violations gbicInvalid: Invalid GBIC errors (examples include unsupported GBIC being inserted) dhcpRateLimit: DHCP snooping rate limit violation unicastFlood: Unicast Flooding threshold violations vmps: VLAN Membership Policy Server feature related errors stormControl: storm control (broadcast/multicast/unicast) threshold violations inlinePower: Errors in inline power arpInspection: Errors detected by Dynamic Arp Inspection (DAI) feature portLoopback: Interface Loopback Error packetBuffer: Packet Buffer Error macLimit: Errors detected by Mac Address Limit feature linkMonitorFailure: Link Monitoring failure oamRemoteFailure: Remote Failure detected by Ethernet OAM (Operations, Administration, and Maintenance) feature dot1adIncompEtype: 802.1ad Ether-type Incompatible errors dot1adIncompTunnel: 802.1ad Pdu Tunnel Incompatible errors sfpConfigMismatch: Mismatch on SFP configuration communityLimit: Vlan Community Limit violations invalidPolicy: QoS Policy violation lsGroup: Errors detected by Link State Group Tracking feature ekey: Errors detected by Error Key Mechanism portModeFailure: Port mode change failure pppoeIaRateLimit: Errors detected by PPPoE Intermediate Agent Rate Limit feature oamRemoteCriticalEvent: Ethernet OAM Remote Critical Event Failure oamRemoteDyingGasp: Ethernet OAM Remote Dying Gasp Failure oamRemoteLinkFault: Ethernet OAM Remote Link Fault Failure mvrp: Errors detected by Multiple VLAN Registration Protocol tranceiverIncomp: Tranceiver incompatible errors other: Any other feature not covered by enumerations listed here portReinitLimitReached: Port reinitialization limit reached adminRxBBCreditPerfBufIncomp: Incompatible admin port rxbbcredit performance buffers ficonNotEnabled: Ficon not enabled adminModeIncomp: Incompatible port admin mode adminSpeedIncomp: Incompatible port admin speed adminRxBBCreditIncomp: Incompatible admin port rxbbcredit adminRxBufSizeIncomp: Incompatible admin port rxbufsize eppFailure: EPP Failure osmEPortUp: First interface in this group is E osmNonEPortUp: Other interfaces in this group are not shut udldUniDir: Unidirectional UDLD detected udldTxRxLoop: UDLD Tx-Rx loop udldNeighbourMismatch: UDLD neighbor mismatch udldEmptyEcho: UDLD empty echo udldAggrasiveModeLinkFailed: UDLD detected link failure in aggressive mode excessivePortInterrupts: Error disabled due to excessive port interrupts channelErrDisabled: Channel error-disabled hwProgFailed: hardware programming failed internalHandshakeFailed: Internal handshake failure stpInconsistencyOnVpcPeerLink: STP inconsistency on VPC peer-link stpPortStateFailure: STP has set port state to failure ipConflict: Error disabled due to IP address conflict multipleMSapIdsRcvd: DCX Multiple MSAP IDs recieved for the port oneHundredPdusWithoutAck: DCX Recieved 100 PDUs without ACK ipQosCompatCheckFailure: IP Qos DCBXP compat check failed loopDetect: Loopdetection in the network
Traps / Notifications
- cErrDisableInterfaceEvent
1.3.6.1.4.1.9.9.548.0.1.1 - cErrDisableInterfaceEventRev1
1.3.6.1.4.1.9.9.548.0.2
Groups and compliance
- ciscoErrDisableFeatureCfgGroup
- ciscoErrDisableFeatureFlapGroup
- ciscoErrDisableGlobalCfgGroup
- ciscoErrDisableIfStatusGroup
- ciscoErrDisableMIBCompliance
- ciscoErrDisableMIBComplianceRev1
- ciscoErrDisableMIBComplianceRev2
- ciscoErrDisableNotifCfgGroup
- ciscoErrDisableNotifGroup
- ciscoErrDisableNotifGroupRev1
- ciscoErrDisableShutdownVlanGroup