CISCO-ENTITY-QFP-MIB
ciscoSystemsThis MIB module defines managed objects that facilitate the
management of Quantum Flow Processors (QFP), which are listed
in the ENTITY-MIB (RFC 4133) entPhysicalTable as an
entPhysicalClass of 'cpu'.
The Quantum Flow Processors (QFP) technology is an architecture
family developed by Cisco, which has fully integrated and
programmable networking chip set that controls different
functions of a system such as packet forwarding.
This module contains objects to monitor various QFP
statistics such as system, utilization, memory, etc.
The utilization statistics can be used for future capacity
planning. The calculation of this statistics may vary by
devices which host QFPs, hence the user must refer to the
specific device document of interest for the exact method
of calculation. The utilization statistics have the following
terminology.
o Input - Communication channel where packets arrive on the
QFP.
o Output - Communication channel where packets leave the QFP.
o Priority - A classification applied to packets indicating
they should be treated with greater urgency.
o Non-Priority - A classification applied to packets indicating
they should be treated with lesser urgency.
o Processing Load - The percentage of time over some interval
that the QFP has spent forwarding packets,
relative to the total time spent both
forwarding packets and being idle.snmptranslate -m CISCO-ENTITY-QFP-MIB -Tpsnmpwalk -v2c -c <community> -m CISCO-ENTITY-QFP-MIB <host> 1.3.6.1.4.1.9.9.715Imports
| CISCO-SMI | ciscoMgmt |
|---|---|
| ENTITY-MIB | entPhysicalIndex |
| HCNUM-TC | CounterBasedGauge64 |
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP |
| SNMPv2-SMI | Bits, Counter32, Counter64, Gauge32, Integer32, IpAddress, MODULE-IDENTITY, MibIdentifier, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, iso |
| SNMPv2-TC | DateAndTime, DisplayString, PhysAddress, TEXTUAL-CONVENTION, TruthValue |
OID tree
| Name | OID | Type | Access | Status | Example | ||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| IciscoEntityQfpMIB | 1.3.6.1.4.1.9.9.715 | ||||||||||||||||||||
identity This MIB module defines managed objects that facilitate the
management of Quantum Flow Processors (QFP), which are listed
in the ENTITY-MIB (RFC 4133) entPhysicalTable as an
entPhysicalClass of 'cpu'.
The Quantum Flow Processors (QFP) technology is an architecture
family developed by Cisco, which has fully integrated and
programmable networking chip set that controls different
functions of a system such as packet forwarding.
This module contains objects to monitor various QFP
statistics such as system, utilization, memory, etc.
The utilization statistics can be used for future capacity
planning. The calculation of this statistics may vary by
devices which host QFPs, hence the user must refer to the
specific device document of interest for the exact method
of calculation. The utilization statistics have the following
terminology.
o Input - Communication channel where packets arrive on the
QFP.
o Output - Communication channel where packets leave the QFP.
o Priority - A classification applied to packets indicating
they should be treated with greater urgency.
o Non-Priority - A classification applied to packets indicating
they should be treated with lesser urgency.
o Processing Load - The percentage of time over some interval
that the QFP has spent forwarding packets,
relative to the total time spent both
forwarding packets and being idle. | |||||||||||||||||||||
| NciscoEntityQfpMIBNotifs | 1.3.6.1.4.1.9.9.715.0 | ||||||||||||||||||||
| !ceqfpMemoryResRisingThreshNotif | 1.3.6.1.4.1.9.9.715.0.1 | ||||||||||||||||||||
notification · current A notification indicating that the QFP memory usage is rising the threshold on this memory resource. This notification will be sent, whenever the QFP memory usage (ceqfpMemoryResInUse) is equal to or above the rising threshold (ceqfpMemoryResRisingThreshold). An agent may throttle the generation of consecutive ceqfpMemoryResRisingThreshNotif notification so that there is at least a five second (suggested default) gap between notification of this type. | |||||||||||||||||||||
| !ceqfpMemoryResFallingThreshNotif | 1.3.6.1.4.1.9.9.715.0.2 | ||||||||||||||||||||
notification · current A notification indicating that the QFP memory usage is equal to or below the falling threshold on this memory resource. This notification will be sent, whenever the QFP memory usage (ceqfpMemoryResInUse) is equal to or below the falling threshold (ceqfpMemoryResFallingThreshold). An agent may throttle the generation of consecutive ceqfpMemoryResFallingThreshNotif notification so that there is at least a five second (suggested default) gap between notification of this type. | |||||||||||||||||||||
| !ceqfpThroughputNotif | 1.3.6.1.4.1.9.9.715.0.3 | ||||||||||||||||||||
notification · current A notification indicating that the average throughput rate for the configured interval has exceeded the threshold or reached maximum bandwidth allowed. This notification will be sent, whenever the ceqfpThroughputLevel object has the value warning(2) or exceed(3). The condition for trap generation will be checked in every ceqfpThroughputInterval. ceqfpThroughputNotif with ceqfpThrougputLevel as warning(2) indicates that average throughput rate has crossed the configured threshold. ceqfpThroughputNotif with ceqfpThrougputLevel as exceed(3) indicates that average throughput rate has reached maximum licensed bandwidth. | |||||||||||||||||||||
| NciscoEntityQfpMIBObjects | 1.3.6.1.4.1.9.9.715.1 | ||||||||||||||||||||
| NciscoEntityQfp | 1.3.6.1.4.1.9.9.715.1.1 | ||||||||||||||||||||
| TceqfpSystemTable | 1.3.6.1.4.1.9.9.715.1.1.1 | NA | |||||||||||||||||||
table · not-accessible · current This table maintains the QFP system information for each QFP physical entity. An agent creates a conceptual row to this table corresponding to a QFP physical entity upon detection of a physical entity supporting the QFP system information. An agent destroys a conceptual row from this table corresponding to a QFP physical entity upon removal of the QFP host physical entity. | |||||||||||||||||||||
| RceqfpSystemEntry | 1.3.6.1.4.1.9.9.715.1.1.1.1 | NA | |||||||||||||||||||
row · not-accessible · current A conceptual row in the ceqfpSystemTable. There is an entry in this table for each QFP entity, as defined by a value of entPhysicalIndex.
| |||||||||||||||||||||
| CceqfpSystemTrafficDirection | 1.3.6.1.4.1.9.9.715.1.1.1.1.1 | INTEGER | RO | both(4) | |||||||||||||||||
column · INTEGER · read-only · current This object represents the traffic direction that this QFP is
assigned to process. The enumerated values are described below.
none (1) - The QFP is not assigned to processes any traffic
yet
ingress (2) - The QFP processes inbound traffic
egress (3) - The QFP processes outbound traffic
both (4) - The QFP processes both inbound and outbound
traffic
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CceqfpSystemState | 1.3.6.1.4.1.9.9.715.1.1.1.1.2 | INTEGER | RO | activeSolo(5) | |||||||||||||||||
column · INTEGER · read-only · current This object represents the current QFP state. The enumerated
values are described below.
unknown (1) - The state of the QFP is unknown
reset (2) - The QFP is reset
init (3) - The QFP is being initialized
active (4) - The QFP is active in a system with redundant
QFP
activeSolo (5) - The QFP is active and there is no redundant
QFP in the system
standby (6) - The QFP is standby in a redundant system.
hotStandby (7) - The QFP is standby and synchronized with
active, so that a switchover in this state
will preserve state of the active. Stateful
datapath features are synchronized between the
active QFP and standby QFP
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CceqfpNumberSystemLoads | 1.3.6.1.4.1.9.9.715.1.1.1.1.3 | Counter32 | RO | 1 | |||||||||||||||||
column · Counter32 · read-only · current This object represents the number of times the QFP is loaded, since the QFP host is up. Example values from LibreNMS test devices
| |||||||||||||||||||||
| CceqfpSystemLastLoadTime | 1.3.6.1.4.1.9.9.715.1.1.1.1.4 | DateAndTime | RO | 07:e3:01:12:0f:26:3b:00 | |||||||||||||||||
column · DateAndTime · read-only · current This object represents the QFP last load time. Example values from LibreNMS test devices
| |||||||||||||||||||||
| SceqfpFiveSecondUtilAlgo | 1.3.6.1.4.1.9.9.715.1.1.2 | INTEGER | RO | fiveSecSample(2) | |||||||||||||||||
scalar · INTEGER · read-only · current This objects represents the method used to calculate 5 Second
interval utilization data. The enumerated values are described
below.
unknown (1) - The calculation method is unknown
fiveSecSample (2) - The value is calculated based on the last
5 second sampling period of utilization
data.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| SceqfpOneMinuteUtilAlgo | 1.3.6.1.4.1.9.9.715.1.1.3 | INTEGER | RO | fiveSecSMA(2) | |||||||||||||||||
scalar · INTEGER · read-only · current This objects represents the method used to calculate 1 Minute
interval utilization data. The enumerated values are described
below.
unknown (1) - The calculation method is unknown
fiveSecSMA (2) - The value is calculated using Simple Moving
Average of last 12 five seconds utilization
data.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| SceqfpFiveMinutesUtilAlgo | 1.3.6.1.4.1.9.9.715.1.1.4 | INTEGER | RO | fiveSecSMA(2) | |||||||||||||||||
scalar · INTEGER · read-only · current This objects represents the method used to calculate 5 Minutes
interval utilization data. The enumerated values are described
below.
unknown (1) - The calculation method is unknown
fiveSecSMA (2) - The value is calculated using Simple Moving
Average of last 60 five seconds utilization
data.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| SceqfpSixtyMinutesUtilAlgo | 1.3.6.1.4.1.9.9.715.1.1.5 | INTEGER | RO | fiveSecSMA(2) | |||||||||||||||||
scalar · INTEGER · read-only · current This objects represents the method used to calculate 60 Minutes
interval utilization data. The enumerated values are described
below.
unknown (1) - The calculation method is unknown
fiveSecSMA (1) - The value is calculated using Simple Moving
Average of last 720 five seconds utilization
data.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| TceqfpUtilizationTable | 1.3.6.1.4.1.9.9.715.1.1.6 | NA | |||||||||||||||||||
table · not-accessible · current This table maintains the utilization statistics collected by each QFP physical entity at various time interval such as last 5 seconds, 1 minute, etc. An agent creates a conceptual row to this table corresponding to a QFP physical entity for a time interval upon detection of a physical entity supporting the utilization statistics for a time interval. The agent destroys a conceptual row from this table corresponding to a QFP physical entity for a time interval upon removal of the QFP host physical entity or it does not receive the utilization statistics update for a certain time period. The time period to wait before deleting an entry from this table would be the discretion of the supporting device. | |||||||||||||||||||||
| RceqfpUtilizationEntry | 1.3.6.1.4.1.9.9.715.1.1.6.1 | NA | |||||||||||||||||||
row · not-accessible · current A conceptual row in the ceqfpUtilizationTable. There is an entry in this table for each QFP entity by a value of entPhysicalIndex and the supported time interval by a value of ceqfpUtilTimeInterval. The method of utilization data calculation for each interval period can be identified through the respective interval scalar objects. For example the utilizaiton data calculation method for 'fiveSecond' interval can be identified by ceqfpFiveSecondUtilAlgo. | |||||||||||||||||||||
| CceqfpUtilTimeInterval | 1.3.6.1.4.1.9.9.715.1.1.6.1.1 | CiscoQfpTimeInterval | NA | ||||||||||||||||||
column · CiscoQfpTimeInterval · not-accessible · current This object identifies the time interval for which the utilization statistics being collected. The interval values can be 5 second, 1 minute, etc. as specified in the CiscoQfpTimeInterval. | |||||||||||||||||||||
| CceqfpUtilInputPriorityPktRate | 1.3.6.1.4.1.9.9.715.1.1.6.1.2 | CiscoQfpPacketRate | RO | 5 | |||||||||||||||||
column · CiscoQfpPacketRate · read-only · current This object represents the QFP input channel priority packet rate during this interval.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CceqfpUtilInputPriorityBitRate | 1.3.6.1.4.1.9.9.715.1.1.6.1.3 | CiscoQfpBitRate | RO | 4256 | |||||||||||||||||
column · CiscoQfpBitRate · read-only · current This object represents the QFP input channel priority bit rate during this interval.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CceqfpUtilInputNonPriorityPktRate | 1.3.6.1.4.1.9.9.715.1.1.6.1.4 | CiscoQfpPacketRate | RO | 539531 | |||||||||||||||||
column · CiscoQfpPacketRate · read-only · current This object represents the QFP input channel non-priority packet rate during this interval.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CceqfpUtilInputNonPriorityBitRate | 1.3.6.1.4.1.9.9.715.1.1.6.1.5 | CiscoQfpBitRate | RO | 3423105432 | |||||||||||||||||
column · CiscoQfpBitRate · read-only · current This object represents the QFP input channel non-priority bit rate during this interval.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CceqfpUtilInputTotalPktRate | 1.3.6.1.4.1.9.9.715.1.1.6.1.6 | CiscoQfpPacketRate | RO | 539536 | |||||||||||||||||
column · CiscoQfpPacketRate · read-only · current This object represents the QFP input channel total packet rate during this interval, which includes both priority and non-priority input packet rate.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CceqfpUtilInputTotalBitRate | 1.3.6.1.4.1.9.9.715.1.1.6.1.7 | CiscoQfpBitRate | RO | 3423109688 | |||||||||||||||||
column · CiscoQfpBitRate · read-only · current This object represents the QFP input channel total bit rate during this interval, which includes both priority and non-priority input bit rate.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CceqfpUtilOutputPriorityPktRate | 1.3.6.1.4.1.9.9.715.1.1.6.1.8 | CiscoQfpPacketRate | RO | 27 | |||||||||||||||||
column · CiscoQfpPacketRate · read-only · current This object represents the QFP output channel priority packet rate during this interval.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CceqfpUtilOutputPriorityBitRate | 1.3.6.1.4.1.9.9.715.1.1.6.1.9 | CiscoQfpBitRate | RO | 30912 | |||||||||||||||||
column · CiscoQfpBitRate · read-only · current This object represents the QFP output channel priority bit rate during this interval.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CceqfpUtilOutputNonPriorityPktRate | 1.3.6.1.4.1.9.9.715.1.1.6.1.10 | CiscoQfpPacketRate | RO | 539536 | |||||||||||||||||
column · CiscoQfpPacketRate · read-only · current This object represents the QFP output channel non-priority packet rate during this interval.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CceqfpUtilOutputNonPriorityBitRate | 1.3.6.1.4.1.9.9.715.1.1.6.1.11 | CiscoQfpBitRate | RO | 3441364544 | |||||||||||||||||
column · CiscoQfpBitRate · read-only · current This object represents the QFP output channel non-priority bit rate during this interval.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CceqfpUtilOutputTotalPktRate | 1.3.6.1.4.1.9.9.715.1.1.6.1.12 | CiscoQfpPacketRate | RO | 539563 | |||||||||||||||||
column · CiscoQfpPacketRate · read-only · current This object represents the QFP output channel total packet rate during this interval, which includes both priority and non-priority output packet rate.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CceqfpUtilOutputTotalBitRate | 1.3.6.1.4.1.9.9.715.1.1.6.1.13 | CiscoQfpBitRate | RO | 3441395456 | |||||||||||||||||
column · CiscoQfpBitRate · read-only · current This object represents the QFP output channel total bit rate during this interval, which includes both priority and non-priority bit rate.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CceqfpUtilProcessingLoad | 1.3.6.1.4.1.9.9.715.1.1.6.1.14 | Gauge32 (0..100) | RO | 7 | |||||||||||||||||
column · Gauge32 (0..100) · read-only · current This object represents the QFP processing load during this interval.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| TceqfpMemoryResourceTable | 1.3.6.1.4.1.9.9.715.1.1.7 | NA | |||||||||||||||||||
table · not-accessible · current This table maintains the memory resources statistics for each QFP physical entity. An agent creates a conceptual row to this table corresponding to a QFP physical entity and its supported memory resource type upon detection of a physical entity supporting the memory resource statistics for a memory resource type. An agent destroys a conceptual row from this table corresponding to a QFP physical entity and its supported memory resource type upon removal of the QFP host physical entity or it does not receive memory resource statistics update for a certain time period. The time period to wait before deleting an entry from this table would be the discretion of the supporting device. | |||||||||||||||||||||
| RceqfpMemoryResourceEntry | 1.3.6.1.4.1.9.9.715.1.1.7.1 | NA | |||||||||||||||||||
row · not-accessible · current A conceptual row in the ceqfpMemoryResourceTable. There is an entry in this table for each QFP entity by a value of entPhysicalIndex and the supported memory resource type by a value of ceqfpMemoryResType. | |||||||||||||||||||||
| CceqfpMemoryResType | 1.3.6.1.4.1.9.9.715.1.1.7.1.1 | CiscoQfpMemoryResource | NA | ||||||||||||||||||
column · CiscoQfpMemoryResource · not-accessible · current This object indicates the type of the memory resource used by the QFP. This object is one of the indices to uniquely identify the QFP memory resource type. | |||||||||||||||||||||
| CceqfpMemoryResTotal | 1.3.6.1.4.1.9.9.715.1.1.7.1.2 | Gauge32 | RO | 1879048192 | |||||||||||||||||
column · Gauge32 · read-only · current This object represents total memory available on this memory resource.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CceqfpMemoryResInUse | 1.3.6.1.4.1.9.9.715.1.1.7.1.3 | Gauge32 | RO | 280443904 | |||||||||||||||||
column · Gauge32 · read-only · current This object represents the memory which is currently under use on this memory resource.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CceqfpMemoryResFree | 1.3.6.1.4.1.9.9.715.1.1.7.1.4 | Gauge32 | RO | 1598607360 | |||||||||||||||||
column · Gauge32 · read-only · current This object represents the memory which is currently free on this memory resource.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CceqfpMemoryResLowFreeWatermark | 1.3.6.1.4.1.9.9.715.1.1.7.1.5 | Gauge32 | RO | 1598141440 | |||||||||||||||||
column · Gauge32 · read-only · current This object represents lowest free water mark on this memory resource.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CceqfpMemoryResRisingThreshold | 1.3.6.1.4.1.9.9.715.1.1.7.1.6 | Unsigned32 (0..100) | RW | 97 | |||||||||||||||||
column · Unsigned32 (0..100) · read-write · current This object represents the rising threshold value for this memory resource. A value of zero means that the rising threshold is not supported for this memory resource. The value of this object can not be set to lower than or equal to ceqfpMemoryResFallingThreshold. A rising (ceqfpMemoryResRisingThreshNotif) notification will be generated, whenever the memory resource usage (ceqfpMemoryHCResInUse) is equal to or greater than this value. After a rising notification is generated, another such notification will not be generated until the ceqfpMemoryResInUse falls below this value and reaches the ceqfpMemoryResFallingThreshold.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CceqfpMemoryResFallingThreshold | 1.3.6.1.4.1.9.9.715.1.1.7.1.7 | Unsigned32 (0..100) | RW | 93 | |||||||||||||||||
column · Unsigned32 (0..100) · read-write · current This object represents the falling threshold value for this memory resource. A value of zero means that the falling threshold is not supported for this memory resource. The value of this object can not be set to higher than or equal to ceqfpMemoryResRisingThreshold. A falling (ceqfpMemoryResRisingThreshNotif) notification will be generated, whenever the memory resource usage (ceqfpMemoryHCResInUse) is equal to or lesser than this value. After a falling notification is generated, another such notification will not be generated until the ceqfpMemoryResInUse rises above this value and reaches the ceqfpMemoryResRisingThreshold.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CceqfpMemoryResTotalOvrflw | 1.3.6.1.4.1.9.9.715.1.1.7.1.8 | Gauge32 | RO | 0 | |||||||||||||||||
column · Gauge32 · read-only · current This object represents the upper 32-bit of ceqfpMemoryResTotal. This object needs to be supported only when the value of ceqfpMemoryResTotal exceeds 32-bit, otherwise this object value would be set to 0.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CceqfpMemoryHCResTotal | 1.3.6.1.4.1.9.9.715.1.1.7.1.9 | CounterBasedGauge64 | RO | 2147483648 | |||||||||||||||||
column · CounterBasedGauge64 · read-only · current This object is a 64-bit version of ceqfpMemoryResTotal.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CceqfpMemoryResInUseOvrflw | 1.3.6.1.4.1.9.9.715.1.1.7.1.10 | Gauge32 | RO | 0 | |||||||||||||||||
column · Gauge32 · read-only · current This object represents the upper 32-bit of ceqfpMemoryResInUse. This object needs to be supported only when the value of ceqfpMemoryResInUse exceeds 32-bit, otherwise this object value would be set to 0.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CceqfpMemoryHCResInUse | 1.3.6.1.4.1.9.9.715.1.1.7.1.11 | CounterBasedGauge64 | RO | 355310592 | |||||||||||||||||
column · CounterBasedGauge64 · read-only · current This object is a 64-bit version of ceqfpMemoryInRes.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CceqfpMemoryResFreeOvrflw | 1.3.6.1.4.1.9.9.715.1.1.7.1.12 | Gauge32 | RO | 0 | |||||||||||||||||
column · Gauge32 · read-only · current This object represents the upper 32-bit of ceqfpMemoryResFree. This object needs to be supported only when the value of ceqfpMemoryResFree exceeds 32-bit, otherwise this object value would be set to 0.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CceqfpMemoryHCResFree | 1.3.6.1.4.1.9.9.715.1.1.7.1.13 | CounterBasedGauge64 | RO | 1792173056 | |||||||||||||||||
column · CounterBasedGauge64 · read-only · current This object is a 64-bit version of ceqfpMemoryResFree.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CceqfpMemoryResLowFreeWatermarkOvrflw | 1.3.6.1.4.1.9.9.715.1.1.7.1.14 | Gauge32 | RO | 0 | |||||||||||||||||
column · Gauge32 · read-only · current This object represents the upper 32-bit of ceqfpMemoryResLowFreeWatermark. This object needs to be supported only when the value of ceqfpMemoryResLowFreeWatermark exceeds 32-bit, otherwise this object value would be set to 0.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CceqfpMemoryHCResLowFreeWatermark | 1.3.6.1.4.1.9.9.715.1.1.7.1.15 | CounterBasedGauge64 | RO | 1715415040 | |||||||||||||||||
column · CounterBasedGauge64 · read-only · current This object is a 64-bit version of ceqfpMemoryResLowFreeWatermark.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| TceqfpThroughputTable | 1.3.6.1.4.1.9.9.715.1.1.8 | NA | |||||||||||||||||||
table · not-accessible · current This table maintains the throughput information for each
QFP physical entity.
An agent creates a conceptual row to this table
corresponding to a QFP physical entity upon detection of a
physical entity supporting the QFP throughput information.
An agent destroys a conceptual row from this table
corresponding to a QFP physical entity upon removal of the QFP
host physical entity. | |||||||||||||||||||||
| RceqfpThroughputEntry | 1.3.6.1.4.1.9.9.715.1.1.8.1 | NA | |||||||||||||||||||
row · not-accessible · current A conceptual row in the ceqfpThroughputTable. There is an entry in this table for each QFP entity, as defined by a value of entPhysicalIndex.
| |||||||||||||||||||||
| CceqfpThroughputLicensedBW | 1.3.6.1.4.1.9.9.715.1.1.8.1.1 | Counter64 | RO | 5000000000 | |||||||||||||||||
column · Counter64 · read-only · current This object represents the bandwidth for installed throughput license.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CceqfpThroughputLevel | 1.3.6.1.4.1.9.9.715.1.1.8.1.2 | INTEGER | RO | normal(1) | |||||||||||||||||
column · INTEGER · read-only · current This object represents the current throughput level for
installed throughput license.
normal (1) - Throughput usage is normal
warning (2) - Throughput usage has crossed the
configured threshold limit
exceed (3) - Throughput usage has exceeded the
total licensed bandwidth
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CceqfpThroughputInterval | 1.3.6.1.4.1.9.9.715.1.1.8.1.3 | Integer32 (10..86400) | RW | 300 | |||||||||||||||||
column · Integer32 (10..86400) · read-write · current The object represents the configured time interval at which the ceqfpThroughputLevel is checked.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CceqfpThroughputThreshold | 1.3.6.1.4.1.9.9.715.1.1.8.1.4 | Integer32 (75..95) | RW | 95 | |||||||||||||||||
column · Integer32 (75..95) · read-write · current The object represents the configured throughput threshold.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| CceqfpThroughputAvgRate | 1.3.6.1.4.1.9.9.715.1.1.8.1.5 | Counter64 | RO | 2859028 | |||||||||||||||||
column · Counter64 · read-only · current The object represents the average throughput rate in the interval ceqfpThroughputInterval.
Example values from LibreNMS test devices
| |||||||||||||||||||||
| NciscoEntityQfpNotif | 1.3.6.1.4.1.9.9.715.1.2 | ||||||||||||||||||||
| SceqfpMemoryResThreshNotifEnabled | 1.3.6.1.4.1.9.9.715.1.2.1 | TruthValue | RW | 2 | |||||||||||||||||
scalar · TruthValue · read-write · current This object controls memory resource rising and falling threshold notification. When this object contains a value 'true', then generation of memory resource threshold notification is enabled. If this object contains a value 'false', then generation of memory resource threshold notification is disabled. Example values from LibreNMS test devices
| |||||||||||||||||||||
| SceqfpMemoryResCurrentRisingThresh | 1.3.6.1.4.1.9.9.715.1.2.2 | Unsigned32 (1..100) | AN | ||||||||||||||||||
scalar · Unsigned32 (1..100) · accessible-for-notify · current This object represents the current rising threshold value, which triggers the rising threshold notification (ceqfpMemoryResRisingThreshNotif).
| |||||||||||||||||||||
| SceqfpMemoryResCurrentFallingThresh | 1.3.6.1.4.1.9.9.715.1.2.3 | Unsigned32 | AN | ||||||||||||||||||
scalar · Unsigned32 · accessible-for-notify · current This object represents the current falling threshold value, which triggers the falling threshold notification (ceqfpMemoryResFallingThreshNotif).
| |||||||||||||||||||||
| SceqfpThroughputNotifEnabled | 1.3.6.1.4.1.9.9.715.1.2.4 | TruthValue | RW | 2 | |||||||||||||||||
scalar · TruthValue · read-write · current This object controls throughput rate notification. When this object contains a value 'true', then generation of ceqfpThroughputNotif is enabled. If this object contains a value 'false', then generation of ceqfpThroughputNotif is disabled. Example values from LibreNMS test devices
| |||||||||||||||||||||
| NciscoEntityQfpMIBConform | 1.3.6.1.4.1.9.9.715.2 | ||||||||||||||||||||
| NciscoEntityQfpMIBCompliances | 1.3.6.1.4.1.9.9.715.2.1 | ||||||||||||||||||||
| MciscoEntityQfpMIBComplianceRev1 | 1.3.6.1.4.1.9.9.715.2.1.1 | deprecated | |||||||||||||||||||
compliance · deprecated The compliance statement for CISCO-ENTITY-QFP-MIB | |||||||||||||||||||||
| MciscoEntityQfpMIBComplianceRev2 | 1.3.6.1.4.1.9.9.715.2.1.2 | ||||||||||||||||||||
compliance · current The compliance statement for CISCO-ENTITY-QFP-MIB. This compliance module deprecates ciscoEntityQfpMIBComplianceRev1. | |||||||||||||||||||||
| NciscoEntityQfpMIBGroups | 1.3.6.1.4.1.9.9.715.2.2 | ||||||||||||||||||||
| GciscoEntityQfpSystemGroup | 1.3.6.1.4.1.9.9.715.2.2.1 | ||||||||||||||||||||
group · current This group contains collection of QFP system information. | |||||||||||||||||||||
| GciscoEntityQfpUtilizationAlgoGroup | 1.3.6.1.4.1.9.9.715.2.2.2 | ||||||||||||||||||||
group · current This group contains collection of QFP utilization algorithm objects. | |||||||||||||||||||||
| GciscoEntityQfpUtilizationGroup | 1.3.6.1.4.1.9.9.715.2.2.3 | ||||||||||||||||||||
group · current This group contains collection of QFP utilization information.
| |||||||||||||||||||||
| GciscoEntityQfpMemoryResourceGroup | 1.3.6.1.4.1.9.9.715.2.2.4 | ||||||||||||||||||||
group · current This group contains collection of QFP memory resource information. | |||||||||||||||||||||
| GciscoEntityQfpNotifGroup | 1.3.6.1.4.1.9.9.715.2.2.5 | ||||||||||||||||||||
group · current This group contains collection of QFP notifications. | |||||||||||||||||||||
| GciscoEntityQfpMemoryResNotifGroup | 1.3.6.1.4.1.9.9.715.2.2.6 | ||||||||||||||||||||
group · current This group contains memory resource notification control objects. | |||||||||||||||||||||
| GciscoEntityQfpMemoryResourceOvrflwGroup | 1.3.6.1.4.1.9.9.715.2.2.7 | ||||||||||||||||||||
group · current This group contains collection of upper 32-bit QFP memory resource information. | |||||||||||||||||||||
| GciscoEntityQfpMemoryHCResourceGroup | 1.3.6.1.4.1.9.9.715.2.2.8 | ||||||||||||||||||||
group · current This group contains collection of high capacity(HC) objects of QFP memory resource information. | |||||||||||||||||||||
| GceqfpThroughputGroup | 1.3.6.1.4.1.9.9.715.2.2.9 | ||||||||||||||||||||
group · current This group contains collection of throughput rate information. | |||||||||||||||||||||
Textual conventions
CiscoQfpBitRateCounter64Display hint:
dAn estimate of throughput in units of bits per second. The CiscoQfpBitRate type represents a non-negative integer, which may increase or decrease, but shall never exceed a maximum value, nor fall below a minimum value of Counter64. The Counter64 syntax is used for encoding rules.
CiscoQfpMemoryResourceINTEGERdram(1)An enumerated integer-value describing various memory resources used by the QFP. dram (1) - Dynamic Random Access Memory (DRAM) memory resource
CiscoQfpPacketRateCounter64Display hint:
dAn estimate of throughput in units of packets per second. The CiscoQfpPacketRate type represents a non-negative integer, which may increase or decrease, but shall never exceed a maximum value, nor fall below a minimum value of Counter64. The Counter64 syntax is used for encoding rules.
CiscoQfpTimeIntervalINTEGERfiveMinutes(3)fiveSeconds(1)oneMinute(2)sixtyMinutes(4)An enumerated integer-value describing the available interval values for which the periodic statistics are to be collected. fiveSeconds (1) - Interval to collect last 5 seconds statistics oneMinute(2) - Interval to collect last 1 minute statistics fiveMinutes(3) - Interval to collect last 5 minutes statistics sixtyMinutes(4) - Interval to collect last 60 minutes statistics
Traps / Notifications
- ceqfpMemoryResFallingThreshNotif
1.3.6.1.4.1.9.9.715.0.2 - ceqfpMemoryResRisingThreshNotif
1.3.6.1.4.1.9.9.715.0.1 - ceqfpThroughputNotif
1.3.6.1.4.1.9.9.715.0.3
Groups and compliance
- ceqfpThroughputGroup
- ciscoEntityQfpMIBComplianceRev1
- ciscoEntityQfpMIBComplianceRev2
- ciscoEntityQfpMemoryHCResourceGroup
- ciscoEntityQfpMemoryResNotifGroup
- ciscoEntityQfpMemoryResourceGroup
- ciscoEntityQfpMemoryResourceOvrflwGroup
- ciscoEntityQfpNotifGroup
- ciscoEntityQfpSystemGroup
- ciscoEntityQfpUtilizationAlgoGroup
- ciscoEntityQfpUtilizationGroup