CISCO-DOT11-IF-MIB
ciscoSystemsThis MIB module provides network management
support for Cisco IEEE 802.11 Wireless LAN
type device (Access Point) radio interfaces.
ACRONYMS
AES
Advanced Encryption Standard
AP
Access point
AID
Association IDentifier for wireless stations.
BSS
IEEE 802.11 Basic Service Set.
CCMP
Code Mode/CBC Mac Protocol
CEPT
European Conference of Postal and
Telecommunications Administrations.
CRC
Cyclic Redundancy Check.
DSSS
Direct-Sequence Spread Spectrum.
EAP
Extensible Authentication Protocol.
ERP
Extended Rate PHY
FHSS
Frequency-Hopping Spread Spectrum.
IAPP
Inter-Access-Point Protocol.
ICV
Integrity Check Value.
ISM
Industrial, Scientific, and Medical.
MBSSID
Multiple Broadcast SSID
MIC
Message Integrity Check.
MMH
Multi-Modal Hashing.
OFDM
Orthogonal Frequency Division Multiplexing.
PHY
Physical Layer (Layer 1 in network model).
PLCP
Physical Layer Convergence Procedure.
PMD
Physical Medium Dependent.
PSPF
Public Secure Packet Forwarding.
RF
Radio Frequency.
SS
Spread-spectrum.
SSID
Radio Service Set ID.
STA
IEEE 802.11 wireless station.
U-NII
Unlicensed National information Infrastructure
VLAN
Virtual LAN.
WEP
Wired Equivalent Privacy.
WGB
Work-group Bridge
WPA
WiFi Protected Access
GLOSSARY
Access point
Transmitter/receiver (transceiver) device
that commonly connects and transports data
between a wireless network and a wired network.
Association
The service used to establish access point
or station mapping and enable STA invocation
of the distribution system services.
(Wireless clients attempt to connect to
access points.)
Basic Rate
A data rate that is mandatory for client
devices to support in order for them to achieve
successful association.
Basic Service Set
The IEEE 802.11 BSS of an AP comprises of the
stations directly associating with the AP.
Bridge
Device that connects two or more segments
and reduces traffic by analyzing the
destination address, filtering the frame,
and forwarding the frame to all connected
segments.
Bridge AP
It is an AP that functions as a transparent
bridge between 2 wired LAN segments.
Broadcast SSID
Clients can send out Broadcast SSID Probe
Requests to a nearby AP, and the AP will
broadcast its own SSID within its beacons
to response to the clients. Clients can use
this Broadcast SSID to associate and
communicate with the AP.
Cyclic Redundancy Check
CRC is an error detect mechanism that applies
to frame transmission.
Direct-Sequence Spread Spectrum
DSSS combines a data signal at the sending
station with a higher data rate bit sequence,
which many refer to as a chipping code (also
known as processing gain). A high processing gain
increases the signals resistance to interference.
DSSS sends a specific string of bits for each data
bit sent.
ERP-CCK Modulation
This signal modulation technique is supported in
PHY implementing IEEE 802.11b/g Protocol.
ERP-OFDM Modulation
This signal modulation technique is supported in
PHY implementing IEEE 802.11g Protocol.
Extensible Authentication Protocol
EAP acts as the interface between a wireless
client and an authentication server, such as a
RADIUS server, to which the access point
communicates over the wired network.
Extended Rate PHY
This PHY implements the IEEE 802.11g Protocol.
Frequency-Hopping Spread Spectrum
In FHSS, a hopping code determines the frequencies
the radio will transmit and in which order. To
properly receive the signal, the receiver must be
set to same hopping code and listen to the
incoming signal at the right time and correct
frequency. The code pattern maintains a single
logical channel.
IEEE 802.11
Standard to encourage interoperability among
wireless networking equipment.
IEEE 802.11b
High-rate wireless LAN standard for wireless
data transfer at up to 11 Mbps.
IEEE P802.11g
Higher Speed Physical Layer (PHY) Extension to
IEEE 802.11b, will boost wireless LAN speed to 54
Mbps by using OFDM (orthogonal frequency division
multiplexing). The IEEE 802.11g specification is
backward compatible with the widely deployed IEEE
802.11b standard.
Inter-Access-Point Protocol
The IEEE 802.11 standard does not define how
access points track moving users or how to
negotiate a handoff from one access point to the
next, a process referred to as roaming. IAPP is
a Cisco proprietary protocol to support roaming.
However, IAPP does not address how the wireless
system tracks users moving from one subnet to
another.
Independent network
Network that provides peer-to-peer connectivity
without relying on a complete network
infrastructure.
Integrity Check Value
The WEP ICV shall be a 32-bit value containing
the 32-bit cyclic redundancy code designed for
verifying wireless data frame integrity.
Message Integrity Check
A MIC can, optionally, be added to WEP-encrypted
802.11 frames. MIC prevents attacks on encrypted
packets. MIC, implemented on both the access point
and all associated client devices, adds a few bytes
to each packet to make the packets tamper-proof.
Native VLAN ID
A switch port and/or AP can be configured with a
'native VLAN ID'. Untagged or priority-tagged
frames are implicitly associated with the native
VLAN ID. The default native VLAN ID is '1' if
VLAN tagging is enabled. The native VLAN ID is '0'
or 'no VLAN ID' if VLAN tagging is not enabled.
Node
Device on a network; has its own unique network
address and name.
Non-Root Bridge
This wireless bridge does not connect to the main
wired LAN segment. It connects to a remote wired
LAN segment and can associate with root bridges and
other non-root bridges that accept client
associations. It also can accept associations from
other non-root bridges, repeater access points,
and client devices.
Physical Layer Convergence Procedure
In IEEE 802.11 wireless LANs, PLCP defines a method
of mapping the IEEE 802.11 MAC sublayer protocol
data units into a framing format suitable for
sending and receiving user data and management
information between two or more wireless stations
using the associated PMD system.
Physical Medium Dependent
In IEEE 802.11 wireless LANs, a PMD system, whose
function defines the characteristics of, and method
of transmitting and receiving data through, a
wireless medium between two or more wireless
stations each using the DSSS.
Preamble
The radio preamble are data at the head of a
packet that contains information access points
and client devices required by IEEE 802.11 when
sending and receiving packets.
Primary LAN
In an AP, if the destinations of inbound unicast
frames are unknown, the frames are sent toward
the primary LAN defined on the device.
Radio carrier
Radio waves that deliver energy to a remote
receiver; in other words, radio waves in a
wireless LAN environment.
Repeater
Device that connects multiple segments,
listening to each and regenerating the signal
on one to every other connected one; so that
the signal can travel further.
Repeater or Non-root Access Point
The repeater access point is not connected
to the wired LAN. The Repeater is a wireless
LAN transceiver that transfers data between
a client and another access point, another
repeater, or between two bridges. The repeater
is placed within radio range of an access point
connected to the wired LAN, another repeater, or
an non-root bridge to extend the range of the
infrastructure.
Radio Frequency
Radio wave and modulation process or operation.
Root Access Point
This access point connects clients to the main
wired LAN.
Root (Wireless) Bridge
This wireless bridge connects to the main wired
LAN. It can communicate with non-root wireless
bridges, repeater access points, and client
devices but not with another wireless root
bridge. Only one wireless bridge in a wireless
LAN can be set as the wireless root bridge.
Spread-spectrum
Wideband radio frequency technique that
consumes more bandwidth than the narrow-band
alternative but produces a signal that is louder
and easier to detect. There are two types of
spread-spectrum radio: frequency hopping and
direct sequence.
Radio Service Set ID
SSID is a unique identifier that APs and clients
use to identify with each other. SSID is a simple
means of access control and is not for security.
The SSID can be any alphanumeric entry up to 32
characters.
Tag header
A 'tag header' is as defined in the IEEE 802.1Q
standard. An 802.1Q tag header contains a 3-bit
priority field and a 12-bit VLAN ID field.
A 'priority tag' has a VLAN ID of 0, to indicate
'no VLAN ID'. A 'VLAN tag' has a non-zero
VLAN ID.
Virtual LAN
VLAN defined in the IEEE 802.1Q VLAN standard
supports logically segmenting of LAN
infrastructure into different subnets or
workgroups so that packets are switched only
between ports within the same VLAN.
VLAN ID
Each VLAN is identified by a 12-bit 'VLAN ID'.
A VLAN ID of '0' is used to indicate
'no VLAN ID'. Valid VLAN IDs range from '1' to
'4095'. VLAN of ID '4095' is the default VLAN
for Cisco VoIP Phones.
Wired Equivalent Privacy
WEP is generally used to refer to 802.11
encryption.
Work-group Bridge
It is a client to APs or wireless root bridges.
The radio port of a WGB serves as the uplink to
the main network and the Ethernet port provides
network access for devices like PC or IP phone.
Upgrade of Frequencies
As per the latest regulations proposed by the
Japanese Government, the four channels 34
( 5170 GHz ), 38 ( 5190 GHz), 42 ( 5210 ) and
44 ( 5230 ) in the 5150-5250 MHz band has been
shifted by 10 MHz. Thus, the new channels in the
5150-5250 MHz band are 36 ( 5180 ), 40 ( 5200 )
and 44 ( 5220 ) and 48 ( 5240 ).snmptranslate -m CISCO-DOT11-IF-MIB -Tpsnmpwalk -v2c -c <community> -m CISCO-DOT11-IF-MIB <host> 1.3.6.1.4.1.9.9.272Imports
| CISCO-SMI | ciscoMgmt |
|---|---|
| IEEE802dot11-MIB | dot11AuthenticationAlgorithmsIndex, dot11SupportedDataRatesRxIndex |
| IF-MIB | ifIndex |
| SNMP-FRAMEWORK-MIB | SnmpAdminString |
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP |
| SNMPv2-SMI | Bits, Counter32, Integer32, IpAddress, MODULE-IDENTITY, MibIdentifier, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, iso |
| SNMPv2-TC | DisplayString, MacAddress, PhysAddress, RowStatus, TEXTUAL-CONVENTION, TruthValue |
OID tree
| Name | OID | Type | Access | Status |
|---|---|---|---|---|
| IciscoDot11IfMIB | 1.3.6.1.4.1.9.9.272 | |||
identity This MIB module provides network management
support for Cisco IEEE 802.11 Wireless LAN
type device (Access Point) radio interfaces.
ACRONYMS
AES
Advanced Encryption Standard
AP
Access point
AID
Association IDentifier for wireless stations.
BSS
IEEE 802.11 Basic Service Set.
CCMP
Code Mode/CBC Mac Protocol
CEPT
European Conference of Postal and
Telecommunications Administrations.
CRC
Cyclic Redundancy Check.
DSSS
Direct-Sequence Spread Spectrum.
EAP
Extensible Authentication Protocol.
ERP
Extended Rate PHY
FHSS
Frequency-Hopping Spread Spectrum.
IAPP
Inter-Access-Point Protocol.
ICV
Integrity Check Value.
ISM
Industrial, Scientific, and Medical.
MBSSID
Multiple Broadcast SSID
MIC
Message Integrity Check.
MMH
Multi-Modal Hashing.
OFDM
Orthogonal Frequency Division Multiplexing.
PHY
Physical Layer (Layer 1 in network model).
PLCP
Physical Layer Convergence Procedure.
PMD
Physical Medium Dependent.
PSPF
Public Secure Packet Forwarding.
RF
Radio Frequency.
SS
Spread-spectrum.
SSID
Radio Service Set ID.
STA
IEEE 802.11 wireless station.
U-NII
Unlicensed National information Infrastructure
VLAN
Virtual LAN.
WEP
Wired Equivalent Privacy.
WGB
Work-group Bridge
WPA
WiFi Protected Access
GLOSSARY
Access point
Transmitter/receiver (transceiver) device
that commonly connects and transports data
between a wireless network and a wired network.
Association
The service used to establish access point
or station mapping and enable STA invocation
of the distribution system services.
(Wireless clients attempt to connect to
access points.)
Basic Rate
A data rate that is mandatory for client
devices to support in order for them to achieve
successful association.
Basic Service Set
The IEEE 802.11 BSS of an AP comprises of the
stations directly associating with the AP.
Bridge
Device that connects two or more segments
and reduces traffic by analyzing the
destination address, filtering the frame,
and forwarding the frame to all connected
segments.
Bridge AP
It is an AP that functions as a transparent
bridge between 2 wired LAN segments.
Broadcast SSID
Clients can send out Broadcast SSID Probe
Requests to a nearby AP, and the AP will
broadcast its own SSID within its beacons
to response to the clients. Clients can use
this Broadcast SSID to associate and
communicate with the AP.
Cyclic Redundancy Check
CRC is an error detect mechanism that applies
to frame transmission.
Direct-Sequence Spread Spectrum
DSSS combines a data signal at the sending
station with a higher data rate bit sequence,
which many refer to as a chipping code (also
known as processing gain). A high processing gain
increases the signals resistance to interference.
DSSS sends a specific string of bits for each data
bit sent.
ERP-CCK Modulation
This signal modulation technique is supported in
PHY implementing IEEE 802.11b/g Protocol.
ERP-OFDM Modulation
This signal modulation technique is supported in
PHY implementing IEEE 802.11g Protocol.
Extensible Authentication Protocol
EAP acts as the interface between a wireless
client and an authentication server, such as a
RADIUS server, to which the access point
communicates over the wired network.
Extended Rate PHY
This PHY implements the IEEE 802.11g Protocol.
Frequency-Hopping Spread Spectrum
In FHSS, a hopping code determines the frequencies
the radio will transmit and in which order. To
properly receive the signal, the receiver must be
set to same hopping code and listen to the
incoming signal at the right time and correct
frequency. The code pattern maintains a single
logical channel.
IEEE 802.11
Standard to encourage interoperability among
wireless networking equipment.
IEEE 802.11b
High-rate wireless LAN standard for wireless
data transfer at up to 11 Mbps.
IEEE P802.11g
Higher Speed Physical Layer (PHY) Extension to
IEEE 802.11b, will boost wireless LAN speed to 54
Mbps by using OFDM (orthogonal frequency division
multiplexing). The IEEE 802.11g specification is
backward compatible with the widely deployed IEEE
802.11b standard.
Inter-Access-Point Protocol
The IEEE 802.11 standard does not define how
access points track moving users or how to
negotiate a handoff from one access point to the
next, a process referred to as roaming. IAPP is
a Cisco proprietary protocol to support roaming.
However, IAPP does not address how the wireless
system tracks users moving from one subnet to
another.
Independent network
Network that provides peer-to-peer connectivity
without relying on a complete network
infrastructure.
Integrity Check Value
The WEP ICV shall be a 32-bit value containing
the 32-bit cyclic redundancy code designed for
verifying wireless data frame integrity.
Message Integrity Check
A MIC can, optionally, be added to WEP-encrypted
802.11 frames. MIC prevents attacks on encrypted
packets. MIC, implemented on both the access point
and all associated client devices, adds a few bytes
to each packet to make the packets tamper-proof.
Native VLAN ID
A switch port and/or AP can be configured with a
'native VLAN ID'. Untagged or priority-tagged
frames are implicitly associated with the native
VLAN ID. The default native VLAN ID is '1' if
VLAN tagging is enabled. The native VLAN ID is '0'
or 'no VLAN ID' if VLAN tagging is not enabled.
Node
Device on a network; has its own unique network
address and name.
Non-Root Bridge
This wireless bridge does not connect to the main
wired LAN segment. It connects to a remote wired
LAN segment and can associate with root bridges and
other non-root bridges that accept client
associations. It also can accept associations from
other non-root bridges, repeater access points,
and client devices.
Physical Layer Convergence Procedure
In IEEE 802.11 wireless LANs, PLCP defines a method
of mapping the IEEE 802.11 MAC sublayer protocol
data units into a framing format suitable for
sending and receiving user data and management
information between two or more wireless stations
using the associated PMD system.
Physical Medium Dependent
In IEEE 802.11 wireless LANs, a PMD system, whose
function defines the characteristics of, and method
of transmitting and receiving data through, a
wireless medium between two or more wireless
stations each using the DSSS.
Preamble
The radio preamble are data at the head of a
packet that contains information access points
and client devices required by IEEE 802.11 when
sending and receiving packets.
Primary LAN
In an AP, if the destinations of inbound unicast
frames are unknown, the frames are sent toward
the primary LAN defined on the device.
Radio carrier
Radio waves that deliver energy to a remote
receiver; in other words, radio waves in a
wireless LAN environment.
Repeater
Device that connects multiple segments,
listening to each and regenerating the signal
on one to every other connected one; so that
the signal can travel further.
Repeater or Non-root Access Point
The repeater access point is not connected
to the wired LAN. The Repeater is a wireless
LAN transceiver that transfers data between
a client and another access point, another
repeater, or between two bridges. The repeater
is placed within radio range of an access point
connected to the wired LAN, another repeater, or
an non-root bridge to extend the range of the
infrastructure.
Radio Frequency
Radio wave and modulation process or operation.
Root Access Point
This access point connects clients to the main
wired LAN.
Root (Wireless) Bridge
This wireless bridge connects to the main wired
LAN. It can communicate with non-root wireless
bridges, repeater access points, and client
devices but not with another wireless root
bridge. Only one wireless bridge in a wireless
LAN can be set as the wireless root bridge.
Spread-spectrum
Wideband radio frequency technique that
consumes more bandwidth than the narrow-band
alternative but produces a signal that is louder
and easier to detect. There are two types of
spread-spectrum radio: frequency hopping and
direct sequence.
Radio Service Set ID
SSID is a unique identifier that APs and clients
use to identify with each other. SSID is a simple
means of access control and is not for security.
The SSID can be any alphanumeric entry up to 32
characters.
Tag header
A 'tag header' is as defined in the IEEE 802.1Q
standard. An 802.1Q tag header contains a 3-bit
priority field and a 12-bit VLAN ID field.
A 'priority tag' has a VLAN ID of 0, to indicate
'no VLAN ID'. A 'VLAN tag' has a non-zero
VLAN ID.
Virtual LAN
VLAN defined in the IEEE 802.1Q VLAN standard
supports logically segmenting of LAN
infrastructure into different subnets or
workgroups so that packets are switched only
between ports within the same VLAN.
VLAN ID
Each VLAN is identified by a 12-bit 'VLAN ID'.
A VLAN ID of '0' is used to indicate
'no VLAN ID'. Valid VLAN IDs range from '1' to
'4095'. VLAN of ID '4095' is the default VLAN
for Cisco VoIP Phones.
Wired Equivalent Privacy
WEP is generally used to refer to 802.11
encryption.
Work-group Bridge
It is a client to APs or wireless root bridges.
The radio port of a WGB serves as the uplink to
the main network and the Ethernet port provides
network access for devices like PC or IP phone.
Upgrade of Frequencies
As per the latest regulations proposed by the
Japanese Government, the four channels 34
( 5170 GHz ), 38 ( 5190 GHz), 42 ( 5210 ) and
44 ( 5230 ) in the 5150-5250 MHz band has been
shifted by 10 MHz. Thus, the new channels in the
5150-5250 MHz band are 36 ( 5180 ), 40 ( 5200 )
and 44 ( 5220 ) and 48 ( 5240 ). | ||||
| NciscoDot11IfMIBNotifications | 1.3.6.1.4.1.9.9.272.0 | |||
| !cd11IfStationSwitchOverNotif | 1.3.6.1.4.1.9.9.272.0.1 | |||
notification · current This notification will be sent when a radio interface changes the cd11IfLocalRadioMonitorStatus from 'monitor' to 'active'. | ||||
| !cd11IfRogueApDetectedNotif | 1.3.6.1.4.1.9.9.272.0.2 | |||
notification · current This notification will be sent when a radio interface detects a new rogue AP and causes a new row to be added to the cd11IfRogueApDetectedTable.
| ||||
| NciscoDot11IfMIBObjects | 1.3.6.1.4.1.9.9.272.1 | |||
| Ncd11IfConfigurations | 1.3.6.1.4.1.9.9.272.1.1 | |||
| Ncd11IfManagement | 1.3.6.1.4.1.9.9.272.1.1.1 | |||
| Tcd11IfStationConfigTable | 1.3.6.1.4.1.9.9.272.1.1.1.1 | NA | ||
table · not-accessible · current This table contains attributes to configure radio interfaces managed by this agent. The attributes are extensions to the configuration parameters in the dot11StationConfigTable defined in the IEEE802dot11-MIB. This table configures the station role of the interface, proprietary extensions, hierarchy, security option and parameters, and communication settings. This table has a sparse dependent relationship on the ifTable. For each entry in this table, there exists an entry in the ifTable of ifType ieee80211(71). Entries in this table cannot be created or deleted by the network management system. All entries are created or deleted by the agent. | ||||
| Rcd11IfStationConfigEntry | 1.3.6.1.4.1.9.9.272.1.1.1.1.1 | NA | ||
row · not-accessible · current A collection of configuration attributes for an IEEE 802.11 radio interface. These attributes are supplements to attributes defined in the dot11StationConfigTable in IEEE802dot11-MIB.
| ||||
| Ccd11IfStationRole | 1.3.6.1.4.1.9.9.272.1.1.1.1.1.1 | INTEGER | RW | |
column · INTEGER · read-write · current This defines the role of this station itself within
the 802.11 BSS of which it is a member. The roles are:
roleWgb(1) - infrastructure type WGB
client,
roleBridge(2) - root bridge,
roleClient(3) - independent BBS type
WGB client,
roleRoot(4) - root access point,
roleRepeater(5) - repeater,
roleApBridge(6) - AP and root bridge,
roleApRepeater(7) - AP and repeater,
roleIBSS(8) - independent BSS,
roleNrBridge(9) - non-root bridge,
roleApNrBridge(10) - AP and non-root bridge,
roleScanner(11) - scanner for rogue APs
and clients.
The default role is roleRoot(4).
| ||||
| Ccd11IfCiscoExtensionsEnable | 1.3.6.1.4.1.9.9.272.1.1.1.1.1.2 | TruthValue | RW | |
column · TruthValue · read-write · current Cisco Aironet extensions to the basic IEEE 802.11 protocols are enabled if the value is 'true'. The extension enables better BSS performance and faster roaming. If the value is 'false', only the basic IEEE 802.11 protocols are used. This ensures maximum compatibility with non-Cisco equipment. The default value is 'true'. | ||||
| Ccd11IfAllowBroadcastSsidAssoc | 1.3.6.1.4.1.9.9.272.1.1.1.1.1.3 | TruthValue | RW | |
column · TruthValue · read-write · current If the value of cd11IfStationRole is either 'roleRoot' or 'roleRepeater', and if cd11IfAllowBroadcastSsidAssoc is 'true', the device radio driver will respond to Broadcast SSID Probe Requests and will broadcast its own SSID within its beacons. If cd11IfAllowBroadcastSsidAssoc is 'false', the radio will not respond to the Broadcast SSID and will not broadcast its SSID within beacons. The default value is 'true'. | ||||
| Ccd11IfPrivacyOptionMaxRate | 1.3.6.1.4.1.9.9.272.1.1.1.1.1.4 | Integer32 (2..127) | RO | |
column · Integer32 (2..127) · read-only · current This object specifies the maximum transmit bit rate supported by the radio when using, for example, WEP encryption. The rate is expressed in standard IEEE 802.11 increments of 500Kb/sec.
| ||||
| Ccd11IfEthernetEncapsulDefault | 1.3.6.1.4.1.9.9.272.1.1.1.1.1.5 | INTEGER | RW | |
column · INTEGER · read-write · current This object specifies the Ethernet encapsulation
transform type used within the BSS. The encapsulations
allowed are either IEEE 802.1H type or RFC-1042 type.
IEEE 802.1H designates the Subnetwork Access Protocol
(SNAP) mechanism as the Ethernet encapsulation protocol.
Subsequently, other (non-IP) uses of the RFC-1042
mechanism. RFC-1042 specifies a translation for
Ethernet frames, such that they can be exchanged with
end stations on LANs that do not provide an Ethernet
service.
encap802dot1H(1) - IEEE 802.1H SNAP encapsulation
encapRfc1042(2) - RFC-1042 encapsulation.
The default encapsulation type is encap802dot1H(1).
| ||||
| Ccd11IfBridgeSpacing | 1.3.6.1.4.1.9.9.272.1.1.1.1.1.6 | Unsigned32 (0..38640) | RW | |
column · Unsigned32 (0..38640) · read-write · current If this device is a root wireless bridge, this value is the distance in kilometers reported between this device and its farthest non-root bridge client.
| ||||
| Ccd11IfDesiredSsidMaxAssocSta | 1.3.6.1.4.1.9.9.272.1.1.1.1.1.7 | Unsigned32 (0..2007) | RW | |
column · Unsigned32 (0..2007) · read-write · current This object defines the maximum number of IEEE 802.11 stations which may associate with this radio interface through IEEE802dot11-MIB dot11DesiredSSID. If this value is '0', the maximum number is limited only by the IEEE 802.11 standard and any hardware or radio firmware limitations of the access point. The default value is '0'. | ||||
| Ccd11IfAuxiliarySsidLength | 1.3.6.1.4.1.9.9.272.1.1.1.1.1.8 | Unsigned32 (0..4095) | RO | |
column · Unsigned32 (0..4095) · read-only · current This object specifies the maximum number of SSIDs allowed for a radio interface or the number of SSID entries per radio interface in the cd11IfAuxSsidTable. The default value is '25'. | ||||
| Ccd11IfVoipExtensionsEnable | 1.3.6.1.4.1.9.9.272.1.1.1.1.1.9 | TruthValue | RW | |
column · TruthValue · read-write · current This object enables the radio generate proprietary elements in its beacons and probe responses to support Voice-over-IP (VoIP) phones. The default value is 'true'. | ||||
| Ccd11IfDesiredSsidMicAlgorithm | 1.3.6.1.4.1.9.9.272.1.1.1.1.1.10 | CDot11IfMicAlgorithm | RW | |
column · CDot11IfMicAlgorithm · read-write · current This object defines the auxiliary MIC calculated on WEP-encoded packets of stations associated with this radio interface through IEEE802dot11-MIB dot11DesiredSSID. The default value is micNone(1). | ||||
| Ccd11IfDesiredSsidWepPermuteAlg | 1.3.6.1.4.1.9.9.272.1.1.1.1.1.11 | CDot11IfWepKeyPermuteAlgorithm | RW | |
column · CDot11IfWepKeyPermuteAlgorithm · read-write · current This object defines the function through which the WEP encryption key is permuted between key renewal periods for stations associated with this radio interface through IEEE802dot11-MIB dot11DesiredSSID. The default value is wepPermuteNone(1). | ||||
| Ccd11IfWorldMode | 1.3.6.1.4.1.9.9.272.1.1.1.1.1.12 | INTEGER | RW | |
column · INTEGER · read-write · current This object sets the World-Mode function of the
radio to allow it to function in countries other
than it was manufactured for.
none(1) - No world mode setting,
legacy(2) - compatible with legacy hardware,
dot11d(3) - use IEEE 802.11d mechanism.
| ||||
| Ccd11IfWorldModeCountry | 1.3.6.1.4.1.9.9.272.1.1.1.1.1.13 | OCTET STRING (SIZE (3)) | RW | |
column · OCTET STRING (SIZE (3)) · read-write · current This object sets the dot11CountryString in the IEEE802dot11-MIB identifying the country in which the radio is operating. When cd11IfWorldMode is either legacy(2) or dot11d(3), this object value will be sent in the radio management frame. The first two octets of this string is the two character country code as described in document ISO/IEC 3166-1. The third octet shall be one of the following: 1. an ASCII space character, if the regulations under which the station is operating encompass all environments in the country, 2. an ASCII 'O' character, if the regulations under which the station is operating are for an Outdoor environment only, or 3. an ASCII 'I' character, if the regulations under which the station is operating are for an Indoor environment only. | ||||
| Ccd11IfMobileStationScanParent | 1.3.6.1.4.1.9.9.272.1.1.1.1.1.14 | TruthValue | RW | |
column · TruthValue · read-write · current This object enables the radio to scan for a better parent when it is a mobile non-root device, for example, the value of cd11IfStationRole is roleWgb(1). | ||||
| Ccd11IfPsPacketForwardEnable | 1.3.6.1.4.1.9.9.272.1.1.1.1.1.15 | TruthValue | RW | |
column · TruthValue · read-write · current If no VLAN is configured on the radio interface, this object configures the PSPF feature. Otherwise, cd11IfVlanPsPacketForwardEnable is used to configure the PSPF feature per VLAN. If it is 'true', PSPF is on the radio interface and direct traffic between wireless clients of the interface is not allowed. If it is 'false', PSPF is disabled on the VLAN and direct traffic between wireless clients of the interface is allowed. | ||||
| Ccd11IfMultipleBssidEnable | 1.3.6.1.4.1.9.9.272.1.1.1.1.1.16 | TruthValue | RW | |
column · TruthValue · read-write · current If it is 'true', multiple broadcast SSID is enabled on the radio. To a wireless client, a MBSSID AP appears to be several distinct co-located APs, and it transmits a beacon for each broadcast SSID or SSID. This allows all of the SSIDs visible for passive scanning. | ||||
| Ccd11IfMobileStationListIgnore | 1.3.6.1.4.1.9.9.272.1.1.1.1.1.17 | TruthValue | RW | |
column · TruthValue · read-write · current This object indicates whether the radio should process the AP adjacency and Enhanced Neighbor List reports specified in the CCX Specification. AP adjacency and Enhanced Neighbor List provide information about the infrastructure wireless devices found in the near vicinity of this radio. This object is applicable only when the radio's role as represented by the object cd11IfStationRole is one of roleWgb(1), roleRepeater(5) or roleNrbridge(9). Agent will populate a value of 'false', when the radio's role as represented by cd11IfStationRole is one of roleRoot(4) ,roleBridge(2) or roleApBridge(6), to indicate that the object is not applicable for the radio in these roles. Set requests will be rejected when the radio is configured to be in one of these roles. User can configure this object only when cd11IfMobileStationScanChannel is configured with a valid set of channels. When cd11IfMobileStationScanChannel is configured with a value of 0, the agent will automatically populate a value of 'false'. | ||||
| Ccd11IfMobileStationScanChannel | 1.3.6.1.4.1.9.9.272.1.1.1.1.1.18 | OCTET STRING (SIZE (1..64)) | RW | |
column · OCTET STRING (SIZE (1..64)) · read-write · current This object specifies the channels to be used by the infractructure clients for scanning purposes. This object is applicable only when the radio's role as represented by the object cd11IfStationRole is one of roleWgb(1), roleRepeater(5) or roleNrbridge(9). Agent will reject the request to set this object when the cd11IfStationRole doesn't populate one of the values mentioned above. Each octet carries the channel number. To configure the radio to scan all the channels applicable to a particular regulatory domain, this object should be configured with only one octet of value 0. | ||||
| Tcd11IfAuthAlgorithmTable | 1.3.6.1.4.1.9.9.272.1.1.1.2 | NA | ||
table · not-accessible · current This table contains attributes to configure authentication algorithm parameters for associations through the SSID defined by IEEE802dot11-MIB dot11DesiredSSID object. It defines attributes additional to those defined in the IEEE802dot11-MIB dot11AuthenticationAlgorithmsTable. An interface may support multiple authentication algorithms. This table has an expansion dependent relationship on the ifTable. For each entry in this table, there exists at least an entry in the ifTable of ifType ieee80211(71). This table uses the dot11AuthenticationAlgorithmsIndex of the dot11AuthenticationAlgorithmsTable defined in the IEEE802dot11-MIB as the expansion index. Entries in this table cannot be created or deleted by the network management system. All entries are created or deleted by the agent. | ||||
| Rcd11IfAuthAlgorithmEntry | 1.3.6.1.4.1.9.9.272.1.1.1.2.1 | NA | ||
row · not-accessible · current Each entry specifies authentication algorithm configuration attributes of a VLAN for the dot11DesiredSSID on a radio interface. | ||||
| Ccd11IfAuthAlgRequireEap | 1.3.6.1.4.1.9.9.272.1.1.1.2.1.1 | TruthValue | RW | |
column · TruthValue · read-write · current If the value is 'true', stations authenticating with the corresponding IEEE802dot11-MIB dot11AuthenticationAlgorithm must complete network-level EAP authentication before their association attempts will be unblocked. If the value is 'false', stations authenticating with the corresponding dot11AuthenticationAlgorithm will be unblocked as soon as they complete the 802.11 authentication. The default value is 'true'. | ||||
| Ccd11IfAuthAlgRequireMacAddr | 1.3.6.1.4.1.9.9.272.1.1.1.2.1.2 | TruthValue | RW | |
column · TruthValue · read-write · current If the value is 'true', stations authenticating with the corresponding IEEE802dot11-MIB dot11AuthenticationAlgorithm must complete additional MAC address authentication before their association attempts will be unblocked. If the value is 'false', stations authenticating with the corresponding dot11AuthenticationAlgorithm will be unblocked as soon as they complete the 802.11 authentication. The default value is 'true'. | ||||
| Ccd11IfAuthAlgDefaultVlan | 1.3.6.1.4.1.9.9.272.1.1.1.2.1.3 | CDot11IfVlanIdOrZero | RW | |
column · CDot11IfVlanIdOrZero · read-write · current This object defines the default VLAN identifier for stations associated with this radio interface with this authentication and through IEEE802dot11-MIB dot11DesiredSSID. If the value of this object is '0', it indicates that either the default VLAN are not defined for this authentication on this radio interface or the default VLAN is the native VLAN ID. The default value is '0'. | ||||
| Ccd11IfAuthAlgEapMethod | 1.3.6.1.4.1.9.9.272.1.1.1.2.1.4 | SnmpAdminString | RW | |
column · SnmpAdminString · read-write · current If the value of cd11IfAuthAlgRequireEap is 'true' or dot11AuthenticationAlgorithm is Network-EAP, this is the EAP method list to used for the EAP authentication. | ||||
| Ccd11IfAuthAlgMacAddrMethod | 1.3.6.1.4.1.9.9.272.1.1.1.2.1.5 | SnmpAdminString | RW | |
column · SnmpAdminString · read-write · current If the value of cd11IfAuthAlgRequireMacAddr is 'true', this is the MAC address method list to used for the MAC authentication. | ||||
| Tcd11IfWepDefaultKeysTable | 1.3.6.1.4.1.9.9.272.1.1.1.3 | NA | ||
table · not-accessible · current The dot11WEPDefaultKeysTable defined by the IEEE802dot11-MIB allows only WEP keys of length up to 40 bits. This table overrides the the dot11WEPDefaultKeysTable and supports keys of from 40 to 128 bits. A maximum of four keys can associate with any IEEE 802.11 radio interface. For devices implementing this table, they should not implement the dot11WEPDefaultKeysTable. This table has an expansion dependent relationship on the ifTable. For each entry in this table, there exists at least an entry in the ifTable of ifType ieee80211(71). Entries in this table cannot be created or deleted by the network management system. All entries are created or deleted by the agent. | ||||
| Rcd11IfWepDefaultKeysEntry | 1.3.6.1.4.1.9.9.272.1.1.1.3.1 | NA | ||
row · not-accessible · current A collection of attributes defining a WEP key for a radio interface. | ||||
| Ccd11IfWepDefaultKeyIndex | 1.3.6.1.4.1.9.9.272.1.1.1.3.1.1 | Unsigned32 (1..4) | NA | |
column · Unsigned32 (1..4) · not-accessible · current This object identifies a WEP key instance for a radio interface. | ||||
| Ccd11IfWepDefaultKeyLen | 1.3.6.1.4.1.9.9.272.1.1.1.3.1.2 | Unsigned32 (5..13) | RW | |
column · Unsigned32 (5..13) · read-write · current This object specifies the length in octets of the WEP key cd11IfWepDefaultKeyValue. The default key length is '13'. | ||||
| Ccd11IfWepDefaultKeyValue | 1.3.6.1.4.1.9.9.272.1.1.1.3.1.3 | WepKeyType128 | RW | |
column · WepKeyType128 · read-write · current This is the WEP default secret key value. Any attempt to read this object by the NMS will result in return of a zero-length string. The default value is a NULL string. | ||||
| Tcd11IfDesiredBssTable | 1.3.6.1.4.1.9.9.272.1.1.1.5 | NA | ||
table · not-accessible · current When the radio is not functioning as an access point (i.e., cd11IfStationRole is not 'roleRoot'), and for example, this radio is a repeater or bridge, this table will contain a list of preferred access points with which the radio interface should associate with. This table has an expansion dependent relationship on the ifTable. For each entry in this table, there exists at least an entry in the ifTable of ifType ieee80211(71). Entries in this table cannot be created or deleted by the network management system. All entries are created or deleted by the agent. | ||||
| Rcd11IfDesiredBssEntry | 1.3.6.1.4.1.9.9.272.1.1.1.5.1 | NA | ||
row · not-accessible · current Each entry provides the MAC address of a preferred access point. A maximum of 4 BSS addresses can be configured to an interface.
| ||||
| Ccd11IfDesiredBssIndex | 1.3.6.1.4.1.9.9.272.1.1.1.5.1.1 | Unsigned32 (1..4) | NA | |
column · Unsigned32 (1..4) · not-accessible · current This object defines the priority order in which preferred access points should be probed. Lower index values indicate higher priority. | ||||
| Ccd11IfDesiredBssAddr | 1.3.6.1.4.1.9.9.272.1.1.1.5.1.2 | MacAddress | RW | |
column · MacAddress · read-write · current This object defines the BSS identifier (MAC address) of the access point with which the radio should try to associate with. The value of this object is '00:00:00:00:00:00' if the BSS identifier for this priority is not specified or configured. The default value is '000000000000'H. | ||||
| Tcd11IfAuxSsidTable | 1.3.6.1.4.1.9.9.272.1.1.1.6 | NA | ||
table · not-accessible · current When the radio is not functioning as a client station (i.e., cd11IfStationRole is not 'roleClient'), and for example, this is a access point or independent BSS, this table will contain a list of SSIDs which stations must be used to associate with this radio. This table has an expansion dependent relationship on the ifTable. For each entry in this table, there exists at least an entry in the ifTable of ifType ieee80211(71). Entries in this table cannot be created or deleted by the network management system. All entries are created or deleted by the agent. | ||||
| Rcd11IfAuxSsidEntry | 1.3.6.1.4.1.9.9.272.1.1.1.6.1 | NA | ||
row · not-accessible · current A collection of attributes defining an auxiliary service set which client stations can associate on the specific interface. An interface can have multiple auxiliary service sets while IEEE 802.11 defines only one desired service set for each interface. Each radio interface currently supports up to 25 SSIDs, and the cd11IfAuxiliarySsidLength object specifies the configured maximum.
| ||||
| Ccd11IfAuxSsidIndex | 1.3.6.1.4.1.9.9.272.1.1.1.6.1.1 | Unsigned32 (1..4095) | NA | |
column · Unsigned32 (1..4095) · not-accessible · current This object identifies a SSID defined on a radio. | ||||
| Ccd11IfAuxSsid | 1.3.6.1.4.1.9.9.272.1.1.1.6.1.2 | OCTET STRING (SIZE (0..32)) | RW | |
column · OCTET STRING (SIZE (0..32)) · read-write · current This object specifies a SSID recognized by this radio interface. The radio interface shall respond to probe requests using this SSID, but it does not advertise this SSID in its beacons. | ||||
| Ccd11IfAuxSsidBroadcastSsid | 1.3.6.1.4.1.9.9.272.1.1.1.6.1.3 | TruthValue | RW | |
column · TruthValue · read-write · current This object indicates if an auxiliary SSID is the Broadcast SSID. There is only one Broadcast SSID per IEEE 802.11 radio interface. | ||||
| Ccd11IfAuxSsidMaxAssocSta | 1.3.6.1.4.1.9.9.272.1.1.1.6.1.4 | Unsigned32 (0..2007) | RW | |
column · Unsigned32 (0..2007) · read-write · current This object defines the maximum number of IEEE 802.11 stations which may associate with this radio interface through the cd11IfAuxSsid. If the value is '0', the maximum number is limited only by the IEEE 802.11 standard and any hardware or radio firmware limitations of the access point. The default value is '0'. | ||||
| Ccd11IfAuxSsidMicAlgorithm | 1.3.6.1.4.1.9.9.272.1.1.1.6.1.5 | CDot11IfMicAlgorithm | RW | |
column · CDot11IfMicAlgorithm · read-write · current This object defines the auxiliary MIC algorithm applied to WEP-encoded packets of stations associated with this radio interface through the cd11IfAuxSsid. The default value is micNone(1). | ||||
| Ccd11IfAuxSsidWepPermuteAlg | 1.3.6.1.4.1.9.9.272.1.1.1.6.1.6 | CDot11IfWepKeyPermuteAlgorithm | RW | |
column · CDot11IfWepKeyPermuteAlgorithm · read-write · current This object defines the function through which the WEP encryption key is permuted between key renewal periods for stations associated with this radio interface through the cd11IfAuxSsid. The default value is wepPermuteNone(1). | ||||
| Tcd11IfAuxSsidAuthAlgTable | 1.3.6.1.4.1.9.9.272.1.1.1.7 | NA | ||
table · not-accessible · current This table contains attributes to configure authentication algorithms for SSIDs listed in the cd11IfAuxSsidTable. This table extends the IEEE802dot11-MIB dot11AuthenticationAlgorithmsTable for multiple SSIDs support. Multiple SSIDs can associate with an interface and multiple authentication algorithms can apply to an auxiliary SSID. This table has an expansion dependent relationship on the ifTable. For each entry in this table, there exists at least an entry in the ifTable of ifType ieee80211(71). Entries in this table cannot be created or deleted by the network management system. All entries are created or deleted by the agent. | ||||
| Rcd11IfAuxSsidAuthAlgEntry | 1.3.6.1.4.1.9.9.272.1.1.1.7.1 | NA | ||
row · not-accessible · current Each entry specifies authentication algorithm configuration attributes of a VLAN for an auxiliary SSID on a radio interface. | ||||
| Ccd11IfAuxSsidAuthAlgEnable | 1.3.6.1.4.1.9.9.272.1.1.1.7.1.1 | TruthValue | RW | |
column · TruthValue · read-write · current If the value is 'true', this device may authenticate an association using SSID (specified by cd11IfAuxiliarySSIDIndex) with the algorithm identified by IEEE802dot11-MIB dot11AuthenticationAlgorithmsIndex. The default value is 'true'. | ||||
| Ccd11IfAuxSsidAuthAlgRequireEap | 1.3.6.1.4.1.9.9.272.1.1.1.7.1.2 | TruthValue | RW | |
column · TruthValue · read-write · current If both the values of this object and cd11IfAuxSsidAuthAlgEnable are 'true', the association authentication must complete additional network-level EAP authentication before client stations will be unblocked from their association attempts. If the value of this object is 'false' while cd11IfAuxSsidAuthAlgEnable is 'true', client stations will be unblocked as soon as they complete this enabled IEEE 802.11 authentication. The default value is 'true'. | ||||
| Ccd11IfAuxSsidAuthAlgRequireMac | 1.3.6.1.4.1.9.9.272.1.1.1.7.1.3 | TruthValue | RW | |
column · TruthValue · read-write · current If both the values of this object and cd11IfAuxSsidAuthAlgEnable are 'true', the association authentication must complete additional MAC address authentication before client stations will be unblocked from their association attempts. If the value of this object is 'false' while cd11IfAuxSsidAuthAlgEnable is 'true', client stations will be unblocked as soon as they complete this enabled IEEE 802.11 authentication. The default value is 'true'. | ||||
| Ccd11IfAuxSsidAuthAlgDefaultVlan | 1.3.6.1.4.1.9.9.272.1.1.1.7.1.4 | CDot11IfVlanIdOrZero | RW | |
column · CDot11IfVlanIdOrZero · read-write · current This object defines the default VLAN identifier for stations associated with this radio interface with the dot11AuthenticationAlgorithmsIndex authentication defined in IEEE802dot11-MIB and through the cd11IfAuxSsid. If the value of this object is '0', it indicates that either the default VLAN are not defined for that authentication on this radio interface or the default VLAN is the native VLAN ID. The default value is '0'. | ||||
| Ccd11IfAuxSsidAuthAlgEapMethod | 1.3.6.1.4.1.9.9.272.1.1.1.7.1.5 | SnmpAdminString | RW | |
column · SnmpAdminString · read-write · current If the value of cd11IfAuxSsidAuthAlgRequireEap is 'true' or dot11AuthenticationAlgorithm is Network-EAP, this is the EAP method list to used for the EAP authentication. | ||||
| Ccd11IfAuxSsidAuthAlgMacMethod | 1.3.6.1.4.1.9.9.272.1.1.1.7.1.6 | SnmpAdminString | RW | |
column · SnmpAdminString · read-write · current If the value of cd11IfAuxSsidAuthAlgRequireMac is 'true', this is the MAC address method list to used for the MAC authentication. | ||||
| Tcd11IfAssignedAidTable | 1.3.6.1.4.1.9.9.272.1.1.1.8 | NA | ||
table · not-accessible · current When the radio is not functioning as a client station (i.e., cd11IfStationRole is not 'roleClient'), this is the list of AIDs which this agent will assign to the clients associating with it. An AID is assigned if the corresponding MAC address matches that of the client. This table has an expansion dependent relationship on the ifTable. For each entry in this table, there exists at least an entry in the ifTable of ifType ieee80211(71). Entries in this table cannot be created or deleted by the network management system. All entries are created or deleted by the agent. | ||||
| Rcd11IfAssignedAidEntry | 1.3.6.1.4.1.9.9.272.1.1.1.8.1 | NA | ||
row · not-accessible · current Each entry associates an AID with a client MAC address. The relationship between AID and client MAC address is one to one.
| ||||
| Ccd11IfAssignedAid | 1.3.6.1.4.1.9.9.272.1.1.1.8.1.1 | Unsigned32 (2..2007) | NA | |
column · Unsigned32 (2..2007) · not-accessible · current This object specifies the AID for a client station to the radio interface. | ||||
| Ccd11IfAssignedSta | 1.3.6.1.4.1.9.9.272.1.1.1.8.1.2 | MacAddress | RW | |
column · MacAddress · read-write · current This object defines the client station MAC address. When a client associates with this radio interface, it shall always be assigned with the cd11IfAssignedAid as its IEEE 802.11 AID. The default value is '000000000000'H. | ||||
| Tcd11IfVlanEncryptKeyTable | 1.3.6.1.4.1.9.9.272.1.1.1.9 | NA | ||
table · not-accessible · current This table contains shared WEP keys for all IEEE 802.11 packets transmitted and received frames over a VLAN identified by the cwvlWlanVlanId if both VLAN and encryption are enabled (i.e., the cwvlWlanEncryptionMode is wep(2) or aes(3)) on the radio interface. If WEP encryption is enabled for the transmitted IEEE 802.11 frames, then the Default Shared WEP key in the set is used to encrypt the transmitted broadcast and multicast frames associated with the cwvlWlanVlanId. Key '1' in the set is the default key. If an individual session key is not defined for the target station address, then the Default Shared WEP key will also be used to encrypt or decrypt unicast frames associated with the cwvlWlanVlanId. | ||||
| Rcd11IfVlanEncryptKeyEntry | 1.3.6.1.4.1.9.9.272.1.1.1.9.1 | NA | ||
row · not-accessible · current Each entry contains the key index, key length, and key value. There is a maximum of 4 keys per VLAN or key set. Each key set exists only if the corresponding VLAN is enabled on the interface, and it is indexed by the VLAN ID. | ||||
| Ccd11IfVlanId | 1.3.6.1.4.1.9.9.272.1.1.1.9.1.1 | CDot11IfVlanIdOrZero | NA | |
column · CDot11IfVlanIdOrZero · not-accessible · current This object identifies the VLAN (1 to 4095) on this radio interface. The object value should match the corresponding cwvlWlanVlanId in the cwvlWlanVlanTable or cd11IfVlanSecurityVlanId object in the cd11IfVlanSecurityTable. When the value is '0', the encryption keys are applied to the non-VLAN configuration. | ||||
| Ccd11IfVlanEncryptKeyIndex | 1.3.6.1.4.1.9.9.272.1.1.1.9.1.2 | Unsigned32 (1..4) | NA | |
column · Unsigned32 (1..4) · not-accessible · current This object is a representative of the corresponding 802.11 WEP Key Index used when transmitting or receiving frames with this key. SNMP table indexing conventions require table index to be non-zero. Therefore, this object has to be one greater than the actual 802.11 WEP key index. A value of '1' for this object corresponds to a value of '0' for the 802.11 WEP key index. | ||||
| Ccd11IfVlanEncryptKeyLen | 1.3.6.1.4.1.9.9.272.1.1.1.9.1.3 | Unsigned32 (0..13) | RC | |
column · Unsigned32 (0..13) · read-create · current This object specifies the length in octets of cd11IfVlanEncryptKeyValue. Common values are 5 for 40-bit WEP key and 13 for 128-bit WEP key. A value of '0' means that the key is not set but the VLAN is enabled. | ||||
| Ccd11IfVlanEncryptKeyValue | 1.3.6.1.4.1.9.9.272.1.1.1.9.1.4 | WepKeyType128 | RC | |
column · WepKeyType128 · read-create · current This is the WEP secret key value. The agent always returns a zero-length string when this object is read for security reason. | ||||
| Ccd11IfVlanEncryptKeyStatus | 1.3.6.1.4.1.9.9.272.1.1.1.9.1.5 | RowStatus | RC | |
column · RowStatus · read-create · current This object controls and reflects the status of rows in this table. When the row in 'active' state, the NMS can modify both key length and value. To delete a row, set this object value to 'destroy'. | ||||
| Ccd11IfVlanEncryptKeyTransmit | 1.3.6.1.4.1.9.9.272.1.1.1.9.1.6 | TruthValue | RC | |
column · TruthValue · read-create · current Only one of the 4 keys of a VLAN can be the transmit key. Setting any one of the 4 keys to 'true', the agent will automatically change the value of cd11IfVlanEncryptKeyTransmit of the other 3 keys to 'false' if they exist. | ||||
| Tcd11IfVlanSecurityTable | 1.3.6.1.4.1.9.9.272.1.1.1.10 | NA | ||
table · not-accessible · current This table contains encryption method and key rotation configurations for all VLANs on all IEEE 802.11 radio interfaces. This table has an expansion dependent relationship on the ifTable. For each entry in this table, there exists at least an entry in the ifTable of ifType ieee80211(71). VLANs are identified by the cd11IfVlanSecurityVlanId, and the actual VLAN does not have to exist or be enabled for the encryption configuration to exist. | ||||
| Rcd11IfVlanSecurityEntry | 1.3.6.1.4.1.9.9.272.1.1.1.10.1 | NA | ||
row · not-accessible · current Each entry is a set of encryption configurations for traffic on a VLAN of a IEEE 802.11 radio interface. | ||||
| Ccd11IfVlanSecurityVlanId | 1.3.6.1.4.1.9.9.272.1.1.1.10.1.1 | CDot11IfVlanIdOrZero | NA | |
column · CDot11IfVlanIdOrZero · not-accessible · current This is the VLAN ID (1-4095) to which the parameters in each conceptual row shall be applied. If the value is '0', these parameters apply to the non-VLAN configuration. | ||||
| Ccd11IfVlanSecurityVlanEnabled | 1.3.6.1.4.1.9.9.272.1.1.1.10.1.2 | TruthValue | RC | |
column · TruthValue · read-create · current If the value is 'true', this VLAN sub-interface is enabled on all trunk and hybrid ports. If the value is 'false', this VLAN is disabled on all ports. For platforms supporting NMS to create VLAN sub-interfaces, setting this object to 'true' will create the corresponding VLAN sub-interfaces on all ports and 'false' will remove the the corresponding VLAN. | ||||
| Ccd11IfVlanBcastKeyChangeInterval | 1.3.6.1.4.1.9.9.272.1.1.1.10.1.3 | Unsigned32 (0 | 10..10000000) | RC | |
column · Unsigned32 (0 | 10..10000000) · read-create · current This is the broadcast key rotation period. If the value is '0', there is no key rotation. | ||||
| Ccd11IfVlanBcastKeyCapabilChange | 1.3.6.1.4.1.9.9.272.1.1.1.10.1.4 | TruthValue | RC | |
column · TruthValue · read-create · current If it is 'true', a new key will be used every time when the common set of encryption capability among clients of this radio on this VLAN is changed. | ||||
| Ccd11IfVlanBcastKeyClientLeave | 1.3.6.1.4.1.9.9.272.1.1.1.10.1.5 | TruthValue | RC | |
column · TruthValue · read-create · current If it is 'true', a new key will be used every time when a client of the radio on this VLAN disassociates. | ||||
| Ccd11IfVlanSecurityCiphers | 1.3.6.1.4.1.9.9.272.1.1.1.10.1.6 | CDot11IfCipherType | RC | |
column · CDot11IfCipherType · read-create · current If cd11IfVlanEncryptionMode is cipher(1), these
are all the possible cipher type combinations
currently supported for data frame encryption from
different IEEE 802.11 radio interface implementations.
Some platform may support only a subset of the
combinations. Agent will not honor invalid
combinations. If none of the bits are set, no
encryption will be done.
aesccm WPA AES CCMP encryption,
ckip Cisco Per packet key hashing,
cmic Cisco MMH MIC,
ckip|cmic Cisco Per packet key hashing and MIC,
tkip WPA Temporal Key encryption,
wep128 128-bit WEP key,
wep40 40-bit WEP key.
tkip|wep128 WPA Temporal Key and 128-bit WEP,
tkip|wep40 WPA Temporal Key and 40-bit WEP. | ||||
| Ccd11IfVlanSecurityRowStatus | 1.3.6.1.4.1.9.9.272.1.1.1.10.1.7 | RowStatus | RC | |
column · RowStatus · read-create · current This is used to create a new row, modify or delete an existing VLAN encryption configuration in this table. Creation of rows must be done via 'createAndGo' and cd11IfVlanSecurityVlanEnabled and cd11IfVlanSecurityCiphers columns are mandatory. This object will become 'active' if the NMS performs a multivarbind set including this object and successfully creates the encryption configuration. Modification and deletion of rows can be done via 'createAndGo' and 'delete' respectively when this object is 'active'. Any encryption configurations of a VLAN should only be deleted when it is not being used for any client association. | ||||
| Ccd11IfVlanEncryptionMode | 1.3.6.1.4.1.9.9.272.1.1.1.10.1.8 | INTEGER | RC | |
column · INTEGER · read-create · current Encryption mode this VLANs are: cipher(1) - WPA and Cisco encryptions, wep(2) - WEP Only encryption
| ||||
| Ccd11IfVlanWepEncryptOptions | 1.3.6.1.4.1.9.9.272.1.1.1.10.1.9 | INTEGER | RC | |
column · INTEGER · read-create · current If cd11IfVlanEncryptionMode is wep(2),
mandatory(1) - WEP encryption is mandatory,
optional(2) - WEP encryption is option.
for all data frames on this VLAN.
| ||||
| Ccd11IfVlanWepEncryptMic | 1.3.6.1.4.1.9.9.272.1.1.1.10.1.10 | TruthValue | RC | |
column · TruthValue · read-create · current If cd11IfVlanEncryptionMode is wep(2) and this object is 'true', MIC will be performed on all data frames on this VLAN. Otherwise, no MIC will be done. | ||||
| Ccd11IfVlanWepEncryptKeyHashing | 1.3.6.1.4.1.9.9.272.1.1.1.10.1.11 | TruthValue | RC | |
column · TruthValue · read-create · current If cd11IfVlanEncryptionMode is wep(2) and this object is 'true', key hashing will be used for encryption. Otherwise, no key hashing will be done. | ||||
| Ccd11IfVlanPsPacketForwardEnable | 1.3.6.1.4.1.9.9.272.1.1.1.10.1.12 | TruthValue | RC | |
column · TruthValue · read-create · current If both cd11IfVlanSecurityVlanEnabled and this object are 'true', PSPF is enabled on VLAN cd11IfVlanSecurityVlanId of this radio interface and direct traffic between wireless clients of the VLAn is not allowed. Otherwise, PSPF is disabled on the VLAN and direct traffic between wireless clients of the VLAN is allowed. | ||||
| Tcd11IfRadioMonitoringTable | 1.3.6.1.4.1.9.9.272.1.1.1.11 | NA | ||
table · not-accessible · current This table is for monitoring of remote active IEEE 802.11 radio devices on the network. Each table entry shows an active radio being monitored by a hot standby radio on this monitoring unit. This table has a sparse dependent relationship on the ifTable. For each entry in this table, there exists an entry in the ifTable of ifType ieee80211(71). Entries on this table can be added, deleted, and modified by the NMS. | ||||
| Rcd11IfRadioMonitoringEntry | 1.3.6.1.4.1.9.9.272.1.1.1.11.1 | NA | ||
row · not-accessible · current Each entry specifies the MAC address of the remote radio and the monitoring configuration and status of the local radio. Most platforms supporting this table only support one entry per ifIndex. | ||||
| Ccd11IfRemoteRadioMacAddr | 1.3.6.1.4.1.9.9.272.1.1.1.11.1.1 | MacAddress | NA | |
column · MacAddress · not-accessible · current Mac address of the active IEEE 802.11 radio device to be monitored by this hot standby monitoring radio. The cd11IfPhyMacSpecification of the local and remote radios must be the same in order for the monitoring to happen. | ||||
| Ccd11IfRadioMonitorPollingFreq | 1.3.6.1.4.1.9.9.272.1.1.1.11.1.2 | Unsigned32 (1..30) | RC | |
column · Unsigned32 (1..30) · read-create · current The frequency, in seconds, the remote active radio specified by cd11IfRemoteRadioMacAddr is polled for its health.
| ||||
| Ccd11IfRadioMonitorPollingTimeOut | 1.3.6.1.4.1.9.9.272.1.1.1.11.1.3 | Unsigned32 (1..600) | RC | |
column · Unsigned32 (1..600) · read-create · current The total time, in seconds, this standby monitoring radio unit can tolerate the failure of polling of the active radio unit. After this duration, one more failure of the polling will trigger this hot standby monitoring radio to take over and become an active radio. It will then stop all monitoring activity and set the instance of cd11IfLocalRadioMonitorStatus indexed by the failed radio cd11IfRemoteRadioMacAddr to 'active'.
| ||||
| Ccd11IfLocalRadioMonitorStatus | 1.3.6.1.4.1.9.9.272.1.1.1.11.1.4 | INTEGER | RC | |
column · INTEGER · read-create · current NMS can only set this object to monitor(2). In the monitor(2) state, this local radio will monitor the remote radio specified in the cd11IfRemoteRadioMacAddr. When the remote radio fails or goes down, this local radio will takeover the functions and became active. The agent will set the instance of cd11IfLocalRadioMonitorStatus indexed by the failed radio cd11IfRemoteRadioMacAddr to 'active'. This local radio will not monitor any other radios when it is active, therefore, all other instances of cd11IfLocalRadioMonitorStatus indexed by the same ifIndex but different cd11IfRemoteRadioMacAddr will be set to 'inactive'.
| ||||
| Ccd11IfRadioMonitorRowStatus | 1.3.6.1.4.1.9.9.272.1.1.1.11.1.5 | RowStatus | RC | |
column · RowStatus · read-create · current This object is used for creating, modifying, and deleting rows in this table. Creation of rows must be done via 'createAndGo'. This object will become 'active' if the NMS performs a multivarbind set including this object. Any object in a row can be modified any time when the row is in the 'active' state via 'createAndGo'. Removal of a row can be done via setting this object to 'destroy'. | ||||
| Tcd11IfDot11UpgradeStatusTable | 1.3.6.1.4.1.9.9.272.1.1.1.12 | NA | ||
table · not-accessible · current This table represents the status of upgrade of the radios to the newer frequencies of the 5150-5250 MHz band. This table has a sparse dependent relationship on the ifTable. For each entry in this table, there exists an entry in the ifTable of ifType ieee80211(71). Entries in this table cannot be created or deleted by the network management system. All entries are created or deleted by the agent. | ||||
| Rcd11IfDot11UpgradeStatusEntry | 1.3.6.1.4.1.9.9.272.1.1.1.12.1 | NA | ||
row · not-accessible · current Each entry corresponds to one conceptual row in cd11IfDot11UpgradeStatusTable and represents the status of upgrade of a dot11 radio interface.
| ||||
| Ccd11IfDot11UpgradeStatus | 1.3.6.1.4.1.9.9.272.1.1.1.12.1.1 | Cd11IfDot11UpgradeStatus | RO | |
column · Cd11IfDot11UpgradeStatus · read-only · current This object represents the status of upgrade of a dot11 radio interface. | ||||
| Ncd11IfPhyConfig | 1.3.6.1.4.1.9.9.272.1.1.2 | |||
| Tcd11IfPhyOperationTable | 1.3.6.1.4.1.9.9.272.1.1.2.1 | NA | ||
table · not-accessible · current This table contains the IEEE 802.11 Physical Layer operation configuration parameters for each radio interface. This table has a sparse dependent relationship on the ifTable. For each entry in this table, there exists an entry in the ifTable of ifType ieee80211(71). Entries in this table cannot be created or deleted by the network management system. All entries are created or deleted by the agent. | ||||
| Rcd11IfPhyOperationEntry | 1.3.6.1.4.1.9.9.272.1.1.2.1.1 | NA | ||
row · not-accessible · current A collection of attributes defining the physical characteristics and behaviors of an IEEE 802.11 PHY.
| ||||
| Ccd11IfCurrentCarrierSet | 1.3.6.1.4.1.9.9.272.1.1.2.1.1.1 | INTEGER | RO | |
column · INTEGER · read-only · current This object defines the carrier set of the radio.
The carrier set implies a regulatory domain, but
geographic-specific restrictions within a regulatory
domain may necessitate several carrier sets within
the regulatory domain.
usa(0) - ISM 2.4 GHz America
europe(1) - ISM 2.4 GHz Europe
japan(2) - ISM 2.4 GHz Japan
spain(3) - ISM 2.4 GHz Spain
france(4) - ISM 2.4 GHz France
belgium(5) - ISM 2.4 GHz Belgium
israel(6) - ISM 2.4 GHz Israel
canada(7) - ISM 2.4 GHz Canada
australia(8) - ISM 2.4 GHz Australia
japanWide(9) - ISM 2.4 GHz JapanWide
world(10) - ISM 2.4 GHz World
usa5GHz(11) - OFDM UNII 2 America
europe5GHz(12) - OFDM UNII 2 Europe
japan5GHz(13) - OFDM UNII 2 Japan
singapore5GHz(14) - OFDM UNII 2 Singapore
taiwan5GHz(15) - OFDM UNII 2 Taiwan
china(16) - ISM 2.4 GHz China
northAmer5GHzUNI3(17)
- OFDM UNII 3 North America
chnIreAus5GHzUNI3(18)
- OFDM UNII 3 China, Ireland, Austrialia
hkNZ5GHzUNI3(19)
- OFDM UNII 3 Hong Kong, New Zealand
korea5GHzUNI3(20)
- OFDM UNII 3 Korea
mexAusNZ5GHzUNI3(21)
- OFDM UNII 3 Mexical, Australia,
New Zealand (North America without
ETSI Channels)
china5GHzUNI2(22)
- OFDM UNII 2 China
korea5GHzUNI123E(23)
- OFDM UNII 1,2,3,ETSI Korea
japan5GHzUNI12(24)
- OFDM UNII 1,2 Japan
taiwan5GHzUNI23E(25)
- OFDM UNII 2,3,ETSI Taiwan
israel5GhzUNI12(26)
- OFDM UNII 1,2 Israel
usaFCC49PS(27)
- OFDM FCC49 USA Public Safety
japan5GHzUNI1(28)
- OFDM UNII 1 Japan
| ||||
| Ccd11IfModulationType | 1.3.6.1.4.1.9.9.272.1.1.2.1.1.2 | INTEGER | RW | |
column · INTEGER · read-write · current This object specifies the RF modulation type of
the radio.
standard(1) - Standard, this is the default
setting currently defined in the
IEEE 802.11 standard.
mok(2) - MOK, this modulation was used
before the IEEE finished the
high-speed 802.11 standard.
The default modulation type is standard(1).
| ||||
| Ccd11IfPreambleType | 1.3.6.1.4.1.9.9.272.1.1.2.1.1.3 | INTEGER | RW | |
column · INTEGER · read-write · current This object specifies the current radio preamble
type in use by the station. Possible values:
long(1) - long preambles
short(2) - short preambles.
A long preamble ensures compatibility between
access point and all early models of Cisco
Aironet Wireless LAN adapters (client devices).
A short preamble improves throughput performance.
The default preamble type is short(2).
| ||||
| Ccd11IfDomainCapabilitySet | 1.3.6.1.4.1.9.9.272.1.1.2.1.1.4 | Integer32 | RW | |
column · Integer32 · read-write · current This object specifies the current multi-domain capability setting of this radio. This object takes one of the dot11MultiDomainCapabilityIndex values on the dot11MultiDomainCapabilityTable. The setting controls the first working radio channel number, the number of working channels, and the maximum transmit power level of the radio. The setting must match the corresponding value of the cd11IfCurrentCarrierSet set for this radio. This object is writable only if the IEEE 802.11 multi-domain capability option is implemented and enabled via dot11MultiDomainCapabilityImplemented and dot11MultiDomainCapabilityEnabled. | ||||
| Ccd11IfPhyBasicRateSet | 1.3.6.1.4.1.9.9.272.1.1.2.1.1.5 | OCTET STRING (SIZE (1..126)) | RW | |
column · OCTET STRING (SIZE (1..126)) · read-write · current This attribute specifies if a data rate in the dot11OperationalRateSet of the IEEE802dot11-MIB is a Basic Rate for this radio interface. If a data rate is a Basic Rate, the corresponding octet of this attribute will contain a value of 128 (or the most significant bit is set). Otherwise, the corresponding octet of this attribute will be 0. | ||||
| Ccd11IfPhyMacSpecification | 1.3.6.1.4.1.9.9.272.1.1.2.1.1.6 | INTEGER | RO | |
column · INTEGER · read-only · current This object specifies which IEEE 802.11 Standard
applies to this radio interface.
ieee802dot11a(1) - IEEE 802.11a Standard,
ieee802dot11b(2) - IEEE 802.11b Standard,
ieee802dot11g(3) - IEEE 802.11g Standard.
| ||||
| Ccd11IfPhyConcatenation | 1.3.6.1.4.1.9.9.272.1.1.2.1.1.7 | Integer32 | RW | |
column · Integer32 · read-write · current If the value of cd11IfStationRole is 'roleBridge' or 'roleNrBridge', this object sets the maximum packet concatenation size in bytes for all outbound packets. For our current 5 GHz product, the maximum value range is from 1600 to 4000. | ||||
| Ccd11IfPhyNativePowerUseStandard | 1.3.6.1.4.1.9.9.272.1.1.2.1.1.8 | TruthValue | RW | |
column · TruthValue · read-write · current This object indicates if queries for current transmit power and number of transmit power levels of the radio for the frequency band shall be via the Standard IEEE802dot11-MIB dot11PhyTxPowerTable dot11CurrentTxPowerLevel and dot11NumberSupportedPowerLevels objects or corresponding cd11IfNativeCurrentPowerLevel and cd11IfNativeNumberPowerLevels objects in the cd11IfRfNativePowerTable. If the value is 'true', the dot11CurrentTxPowerLevel is used to configure the current radio transmit power level. If the value is 'false', the cd11IfNativeCurrentPowerLevel object shall be used to configure the current radio transmit power level. | ||||
| Tcd11IfPhyFhssTable | 1.3.6.1.4.1.9.9.272.1.1.2.4 | NA | ||
table · not-accessible · current This table contains the Physical Layer Frequency Hopping Spread Spectrum configuration parameters for each radio interface. This table has a sparse dependent relationship on the ifTable. For each entry in this table, there exists an entry in the ifTable of ifType ieee80211(71). Entries in this table cannot be created or deleted by the network management system. All entries are created or deleted by the agent. | ||||
| Rcd11IfPhyFhssEntry | 1.3.6.1.4.1.9.9.272.1.1.2.4.1 | NA | ||
row · not-accessible · current A collection of attributes defining the FHSS configuration parameters of a radio interface.
| ||||
| Ccd11IfPhyFhssMaxCompatibleRate | 1.3.6.1.4.1.9.9.272.1.1.2.4.1.1 | Integer32 (2..127) | RW | |
column · Integer32 (2..127) · read-write · current This object specifies the of maximum data rate at which the station may transmit data. The octet contains a value representing a rate. The rate should be within the range from '2' to '127', corresponding to data rates in increments of 500 kb/s from 1 Mb/s to 63.5 Mb/s. It should be one of the rates in the IEEE802dot11-MIB dot11OperationalRateSet. The default value is '127'.
| ||||
| Tcd11IfPhyDsssTable | 1.3.6.1.4.1.9.9.272.1.1.2.5 | NA | ||
table · not-accessible · current This table contains the Physical Layer Direct Sequence Spread Spectrum configuration parameters for each radio interface. This table has a sparse dependent relationship on the ifTable. For each entry in this table, there exists an entry in the ifTable of ifType ieee80211(71). Entries in this table cannot be created or deleted by the network management system. All entries are created or deleted by the agent. | ||||
| Rcd11IfPhyDsssEntry | 1.3.6.1.4.1.9.9.272.1.1.2.5.1 | NA | ||
row · not-accessible · current A collection of attributes defining the DSSS configuration parameters of a radio interface.
| ||||
| Ccd11IfPhyDsssMaxCompatibleRate | 1.3.6.1.4.1.9.9.272.1.1.2.5.1.1 | Integer32 (2..127) | RW | |
column · Integer32 (2..127) · read-write · current This object specifies the of maximum data rate at which the station may transmit data. The octet contains a value representing a rate. The rate should be within the range from '2' to '127', corresponding to data rates in increments of 500 kb/s from 1 Mb/s to 63.5 Mb/s. It should be one of the rates in the IEEE802dot11-MIB dot11OperationalRateSet. The default value is '127'.
| ||||
| Ccd11IfPhyDsssChannelAutoEnable | 1.3.6.1.4.1.9.9.272.1.1.2.5.1.2 | TruthValue | RW | |
column · TruthValue · read-write · current If the value is 'true' and the radio is function as an access point device (i.e., cd11IfStationRole is 'roleRoot', the radio will scan for other BSS activity on all channels available in the current cd11IfCurrentCarrierSet before establishing its own BSS. After the scan, this station will establish its own BSS on the channel with the least probability of radio signal congestion. If the value is 'false', this station always establishes its BSS on IEEE802dot11-MIB dot11CurrentChannel. The default value is 'true'. | ||||
| Ccd11IfPhyDsssCurrentChannel | 1.3.6.1.4.1.9.9.272.1.1.2.5.1.3 | INTEGER (1..14 | 34 | 36 | 38 | 40 | 42 | 44 | 46 | 48 | 52 | 56 | 60 | 64 | 149 | 153 | 157 | 161) | RO | |
column · INTEGER (1..14 | 34 | 36 | 38 | 40 | 42 | 44 | 46 | 48 | 52 | 56 | 60 | 64 | 149 | 153 | 157 | 161) · read-only · current The current operating frequency channel of the DSSS PHY, as selected either by selective scanning or via IEEE802dot11-MIB dot11CurrentChannel. Valid channel numbers are defined in the IEEE 802.11 Standard. For North America, 802.11b channels allowed are 1 to 11 and 802.11a channels allowed are 36,40,44,48,52,56, 60, and 64. | ||||
| Tcd11IfSuppDataRatesPrivacyTable | 1.3.6.1.4.1.9.9.272.1.1.2.11 | NA | ||
table · not-accessible · current This table defines the transmit and receive bit rate of the radio on each IEEE 802.11 interface and the WEP encryption support at those rates. This table has an expansion dependent relationship on the ifTable. For each entry in this table, there exists at least an entry in the ifTable of ifType ieee80211(71). Entries in this table cannot be created or deleted by the network management system. All entries are created or deleted by the agent. | ||||
| Rcd11IfSuppDataRatesPrivacyEntry | 1.3.6.1.4.1.9.9.272.1.1.2.11.1 | NA | ||
row · not-accessible · current Each entry specifies the encryption support for a particular data rate on a radio interface. | ||||
| Ccd11IfSuppDataRatesPrivacyIndex | 1.3.6.1.4.1.9.9.272.1.1.2.11.1.1 | Integer32 (1..8) | NA | |
column · Integer32 (1..8) · not-accessible · current This object identifies a data rate supported on a radio. Each radio can support up to 8 different rates. | ||||
| Ccd11IfSuppDataRatesPrivacyValue | 1.3.6.1.4.1.9.9.272.1.1.2.11.1.2 | Integer32 (2..127) | RO | |
column · Integer32 (2..127) · read-only · current This object defines the receiving or transmission bit rates supported by the PLCP and PMD, represented by a count from 0x02-0x7f, corresponding to data rates in increments of 500Kb/s from 1 Mb/s to 63.5 Mb/s.
| ||||
| Ccd11IfSuppDataRatesPrivacyEnabl | 1.3.6.1.4.1.9.9.272.1.1.2.11.1.3 | TruthValue | RO | |
column · TruthValue · read-only · current This object indicates whether WEP encryption is supported by the radio for both transmit and receive operations at the corresponding bit rate specified by the cd11IfSuppDataRatesPrivacyValue. | ||||
| Tcd11IfChanSelectTable | 1.3.6.1.4.1.9.9.272.1.1.2.12 | NA | ||
table · not-accessible · current This table specifies for each 802.11 channel, whether the scanning process controlled by the cd11IfPhyDsssChannelAutoEnable can select a particular channel for use. This table has an expansion dependent relationship on the ifTable. For each entry in this table, there exists at least an entry in the ifTable of ifType ieee80211(71). Entries in this table cannot be created or deleted by the network management system. All entries are created or deleted by the agent. | ||||
| Rcd11IfChanSelectEntry | 1.3.6.1.4.1.9.9.272.1.1.2.12.1 | NA | ||
row · not-accessible · current Each entry specifies if a particular radio channel is enabled on a radio interface. | ||||
| Ccd11IfChanSelectChannel | 1.3.6.1.4.1.9.9.272.1.1.2.12.1.1 | INTEGER (1..14 | 34 | 36 | 38 | 40 | 42 | 44 | 46 | 48 | 52 | 56 | 60 | 64 | 149 | 153 | 157 | 161) | NA | |
column · INTEGER (1..14 | 34 | 36 | 38 | 40 | 42 | 44 | 46 | 48 | 52 | 56 | 60 | 64 | 149 | 153 | 157 | 161) · not-accessible · current This object specifies an IEEE 802.11 channel number which is a candidate for low-occupancy scanning. | ||||
| Ccd11IfChanSelectEnable | 1.3.6.1.4.1.9.9.272.1.1.2.12.1.2 | TruthValue | RW | |
column · TruthValue · read-write · current If the value is 'true', cd11IfChanSelectChannel is available for the system to use as its cd11IfPhyDsssCurrentChannel after scanning for channel occupancy. If the value is 'false', cd11IfChanSelectChannel is not available. The default value is 'true'. | ||||
| Tcd11IfClientTxPowerTable | 1.3.6.1.4.1.9.9.272.1.1.2.13 | NA | ||
table · not-accessible · current This table shows the recommended client transmit power level for the radio and selects one of the levels as the desired transmit power level to be used by the client of the radio. By adjusting the transmit power, the radio can limit the interference caused by adjacent clients using the same or adjacent channels. | ||||
| Rcd11IfClientTxPowerEntry | 1.3.6.1.4.1.9.9.272.1.1.2.13.1 | NA | ||
row · not-accessible · current Each entry specifies the number of available transmit power levels, the values of all the levels, and the selected level for a radio interface.
| ||||
| Ccd11IfClientNumberTxPowerLevels | 1.3.6.1.4.1.9.9.272.1.1.2.13.1.1 | Integer32 (1..8) | RO | |
column · Integer32 (1..8) · read-only · current The number of power levels available for the clients. This attribute can have a value of 1 to 8. | ||||
| Ccd11IfClientTxPowerLevel1 | 1.3.6.1.4.1.9.9.272.1.1.2.13.1.2 | Integer32 (-10000..10000) | RO | |
column · Integer32 (-10000..10000) · read-only · current The client transmit output power for LEVEL1 in mW or dBm. | ||||
| Ccd11IfClientTxPowerLevel2 | 1.3.6.1.4.1.9.9.272.1.1.2.13.1.3 | Integer32 (-10000..10000) | RO | |
column · Integer32 (-10000..10000) · read-only · current The client transmit output power for LEVEL2 in mW or dBm. | ||||
| Ccd11IfClientTxPowerLevel3 | 1.3.6.1.4.1.9.9.272.1.1.2.13.1.4 | Integer32 (-10000..10000) | RO | |
column · Integer32 (-10000..10000) · read-only · current The client transmit output power for LEVEL3 in mW or dBm. | ||||
| Ccd11IfClientTxPowerLevel4 | 1.3.6.1.4.1.9.9.272.1.1.2.13.1.5 | Integer32 (-10000..10000) | RO | |
column · Integer32 (-10000..10000) · read-only · current The client transmit output power for LEVEL4 in mW or dBm. | ||||
| Ccd11IfClientTxPowerLevel5 | 1.3.6.1.4.1.9.9.272.1.1.2.13.1.6 | Integer32 (-10000..10000) | RO | |
column · Integer32 (-10000..10000) · read-only · current The client transmit output power for LEVEL5 in mW or dBm. | ||||
| Ccd11IfClientTxPowerLevel6 | 1.3.6.1.4.1.9.9.272.1.1.2.13.1.7 | Integer32 (-10000..10000) | RO | |
column · Integer32 (-10000..10000) · read-only · current The client transmit output power for LEVEL6 in mW or dBm. | ||||
| Ccd11IfClientTxPowerLevel7 | 1.3.6.1.4.1.9.9.272.1.1.2.13.1.8 | Integer32 (-10000..10000) | RO | |
column · Integer32 (-10000..10000) · read-only · current The client transmit output power for LEVEL7 in mW or dBm. | ||||
| Ccd11IfClientTxPowerLevel8 | 1.3.6.1.4.1.9.9.272.1.1.2.13.1.9 | Integer32 (-10000..10000) | RO | |
column · Integer32 (-10000..10000) · read-only · current The client transmit output power for LEVEL8 in mW or dBm. | ||||
| Ccd11IfClientCurrentTxPowerLevel | 1.3.6.1.4.1.9.9.272.1.1.2.13.1.10 | Integer32 (1..8) | RW | |
column · Integer32 (1..8) · read-write · current The TxPowerLevel N currently selected for client to transmit data. It is up to the clients to honor this transmit power setting. | ||||
| Tcd11IfErpOfdmTxPowerTable | 1.3.6.1.4.1.9.9.272.1.1.2.14 | NA | ||
table · not-accessible · current This table shows the available ERP-OFDM transmit power levels for radios implementing IEEE 802.11g Protocol and configures one of the levels as the transmit power level. This table has a sparse dependent relationship on the ifTable. For each entry in this table, there exists an entry in the ifTable of ifType ieee80211(71) and the corresponding cd11IfPhyMacSpecification is ieee802dot11g(3). For all IEEE802.11g radios with an entry in this table, the IEEE802dot11-MIB dot11PhyTxPowerTable will be used to configure ERP-CCK transmit power levels. | ||||
| Rcd11IfErpOfdmTxPowerEntry | 1.3.6.1.4.1.9.9.272.1.1.2.14.1 | NA | ||
row · not-accessible · current Each entry specifies the number of available transmit power levels, the values of all the levels, and the configured transmit power level for an IEEE 802.11g radio interface.
| ||||
| Ccd11IfErpOfdmNumberTxPowerLevels | 1.3.6.1.4.1.9.9.272.1.1.2.14.1.1 | Integer32 (1..8) | RO | |
column · Integer32 (1..8) · read-only · current The number of power levels available for this radio. This attribute can have a value of 1 to 8. | ||||
| Ccd11IfErpOfdmTxPowerLevel1 | 1.3.6.1.4.1.9.9.272.1.1.2.14.1.2 | Integer32 (0..10000) | RO | |
column · Integer32 (0..10000) · read-only · current The ERP-OFDM transmit output power for LEVEL1.
| ||||
| Ccd11IfErpOfdmTxPowerLevel2 | 1.3.6.1.4.1.9.9.272.1.1.2.14.1.3 | Integer32 (0..10000) | RO | |
column · Integer32 (0..10000) · read-only · current The ERP-OFDM transmit output power for LEVEL2.
| ||||
| Ccd11IfErpOfdmTxPowerLevel3 | 1.3.6.1.4.1.9.9.272.1.1.2.14.1.4 | Integer32 (0..10000) | RO | |
column · Integer32 (0..10000) · read-only · current The ERP-OFDM transmit output power for LEVEL3.
| ||||
| Ccd11IfErpOfdmTxPowerLevel4 | 1.3.6.1.4.1.9.9.272.1.1.2.14.1.5 | Integer32 (0..10000) | RO | |
column · Integer32 (0..10000) · read-only · current The ERP-OFDM transmit output power for LEVEL4.
| ||||
| Ccd11IfErpOfdmTxPowerLevel5 | 1.3.6.1.4.1.9.9.272.1.1.2.14.1.6 | Integer32 (0..10000) | RO | |
column · Integer32 (0..10000) · read-only · current The ERP-OFDM transmit output power for LEVEL5.
| ||||
| Ccd11IfErpOfdmTxPowerLevel6 | 1.3.6.1.4.1.9.9.272.1.1.2.14.1.7 | Integer32 (0..10000) | RO | |
column · Integer32 (0..10000) · read-only · current The ERP-OFDM transmit output power for LEVEL6.
| ||||
| Ccd11IfErpOfdmTxPowerLevel7 | 1.3.6.1.4.1.9.9.272.1.1.2.14.1.8 | Integer32 (0..10000) | RO | |
column · Integer32 (0..10000) · read-only · current The ERP-OFDM transmit output power for LEVEL7.
| ||||
| Ccd11IfErpOfdmTxPowerLevel8 | 1.3.6.1.4.1.9.9.272.1.1.2.14.1.9 | Integer32 (0..10000) | RO | |
column · Integer32 (0..10000) · read-only · current The ERP-OFDM transmit output power for LEVEL8.
| ||||
| Ccd11IfErpOfdmCurrentTxPowerLevel | 1.3.6.1.4.1.9.9.272.1.1.2.14.1.10 | Integer32 (1..8) | RW | |
column · Integer32 (1..8) · read-write · current The TxPowerLevel N currently configured to transmit data. | ||||
| Tcd11IfFrequencyBandTable | 1.3.6.1.4.1.9.9.272.1.1.2.15 | NA | ||
table · not-accessible · current This table identifies the radio frequency (sub)bands supported on the IEEE 802.11 radio interfaces while operating per the regulations imposed by the cd11IfCurrentCarrierSet. This table has an expansion dependent relationship on the ifTable. For each entry in this table, there exists at least an entry in the ifTable of ifType ieee80211(71). This table uses the cd11IfRfFrequencyBand as the expansion index. All entries in this table are created or deleted only by the agent. | ||||
| Rcd11IfFrequencyBandEntry | 1.3.6.1.4.1.9.9.272.1.1.2.15.1 | NA | ||
row · not-accessible · current Each entry defines a supported radio frequency band for an IEEE 802.11 radio interface.
| ||||
| Ccd11IfRfFrequencyBand | 1.3.6.1.4.1.9.9.272.1.1.2.15.1.1 | Unsigned32 | NA | |
column · Unsigned32 · not-accessible · current This object identifies radio frequency bands supported on the radio. | ||||
| Ccd11IfRfFrequencyUnits | 1.3.6.1.4.1.9.9.272.1.1.2.15.1.2 | INTEGER | RO | |
column · INTEGER · read-only · current This base frequency units combines with the cd11IfRfStartChannelFrequency to define the actual frequency of the channel and combines with the cd11IfRfFrequencySpacing to define the minimum frequency spacing between two adjacent frequency channels. For example, frequency spacing of 5 MHz is 'mHz' in cd11IfRfFrequencyUnits and 5 in cd11IfRfFrequencySpacing.
| ||||
| Ccd11IfRfStartChannelNumber | 1.3.6.1.4.1.9.9.272.1.1.2.15.1.3 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current Numeric identifier of the first channel supported in this radio frequency band. For example, currently at the 2.4 GHz ISM band, the first channel number is 1, while for the U-NII-1 band in the FCC regulatory domain, the first supported channel is number 36 at frequency 5180 MHz. | ||||
| Ccd11IfRfEndChannelNumber | 1.3.6.1.4.1.9.9.272.1.1.2.15.1.4 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current Numeric identifier of the last channel supported in this radio frequency band. For example, in the FCC regulatory domain, the last channel of the 2.4 GHz ISM band is number 11 and the last channel of the U-NII-1 band is number 48 at frequency 5240 MHz. | ||||
| Ccd11IfRfChannelSpacingNumber | 1.3.6.1.4.1.9.9.272.1.1.2.15.1.5 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current Numeric spacing between the identifiers of two adjacent supported channels in this band. For example, currently at the 2.4 GHz ISM band, the numeric channel spacing is 1, resulting in a channel identifier sequence of 1, 2, 3, etc. In the U-NII-1 band, the numeric channel spacing is 4, resulting in a channel identifier sequence of 36, 40, 44, etc. | ||||
| Ccd11IfRfStartChannelFrequency | 1.3.6.1.4.1.9.9.272.1.1.2.15.1.6 | Unsigned32 (0..10000) | RO | |
column · Unsigned32 (0..10000) · read-only · current This is the base channel frequency of the cd11IfRfStartChannelNumber channel from which subsequent channels of this frequency band are defined. The actual frequency value is defined and calculated by multiplying this object with the cd11IfRfFrequencyUnits. The subsequent channels in the band are calculated by adding the cd11IfRfChannelSpacingNumber multiplied by the cd11IfRfFrequencySpacing to this object value. For example, the first channel of U-NII-1 band is channel 36, the cd11IfRfFrequencyUnits is 'mHz', the cd11IfRfStartChannelFrequency is '5180', and the cd11IfRfChannelSpacingNumber is 4. If the cd11IfRfFrequencySpacing is 5 MHz, the second supported channel of the U-NII-1 band will be channel 40 at frequency 5200 MHz. | ||||
| Ccd11IfRfFrequencySpacing | 1.3.6.1.4.1.9.9.272.1.1.2.15.1.7 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current This is the frequency separation between two adjacent radio frequency channels. The actual frequency value is calculated by multiplying this object with the cd11IfRfFrequencyUnits. For example, for a frequency spacing of 5 MHz, the value of cd11IfRfFrequencyUnits is 'mHz' and the value of this object is 5. | ||||
| Ccd11IfRfFrequencyBandType | 1.3.6.1.4.1.9.9.272.1.1.2.15.1.8 | CDot11RadioFrequencyBandType | RO | |
column · CDot11RadioFrequencyBandType · read-only · current This is the enumerated radio frequency band name(s) which this (sub)band occupies. If the frequency band defined in a table row is not included in the current CDot11RadioFrequencyBandType definition, none of the bits are set for this object. | ||||
| Ccd11IfMaxChannelSwitchTime | 1.3.6.1.4.1.9.9.272.1.1.2.15.1.9 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current The maximum time required for the radio interface to switch its transceiver from one channel to any other supported channel in any supported band.
| ||||
| Tcd11IfNativeTxPowerSupportTable | 1.3.6.1.4.1.9.9.272.1.1.2.16 | NA | ||
table · not-accessible · current This table shows the transmit powers supported for all the radio frequency bands on the IEEE 802.11 radios. This table has an expansion dependent relationship on the ifTable. For each entry in this table, there exists at least an entry in the ifTable of ifType ieee80211(71). This table uses the cd11IfRfFrequencyBand of cd11IfFrequencyBandTable, cd11IfRadioModulationClass, and cd11IfNativeTxPowerLevel as the expansion indices. All entries in this table can only be created or deleted by the agent. | ||||
| Rcd11IfNativeTxPowerSupportEntry | 1.3.6.1.4.1.9.9.272.1.1.2.16.1 | NA | ||
row · not-accessible · current Each entry specifies a supported transmit power level for a frequency band, with a specified modulation technique, on the IEEE 802.11 radio interface. | ||||
| Ccd11IfRadioModulationClass | 1.3.6.1.4.1.9.9.272.1.1.2.16.1.1 | CDot11RadioModulationClass | NA | |
column · CDot11RadioModulationClass · not-accessible · current This identifies a radio modulation technique used by the 802.11 radio interface. | ||||
| Ccd11IfNativeTxPowerLevel | 1.3.6.1.4.1.9.9.272.1.1.2.16.1.2 | Unsigned32 | NA | |
column · Unsigned32 · not-accessible · current This is the unique index for a transmit power of a radio frequency band for the radio. | ||||
| Ccd11IfNativeTxPower | 1.3.6.1.4.1.9.9.272.1.1.2.16.1.3 | Integer32 | RO | |
column · Integer32 · read-only · current This is a transmit power available at a radio frequency band for the radio, when using the modulation technique specified by the cd11IfRadioModulationClass. The value of the cd11IfNativeTxPowerUnits defines the units of this transmit power. The value can be negative if the units is 'dBm'. | ||||
| Tcd11IfRfNativePowerTable | 1.3.6.1.4.1.9.9.272.1.1.2.17 | NA | ||
table · not-accessible · current This table configures the radio power settings for frequency bands supported on the IEEE 802.11 radios. This table serves as an alternative for the IEEE802dot11-MIB dot11PhyTxPowerTable. This table allows different transmit powers to be used on different radio frequency bands. This table has an expansion dependent relationship on the ifTable. For each entry in this table, there exists at least an entry in the ifTable of ifType ieee80211(71). This table uses the cd11IfRfFrequencyBand and cd11IfRadioModulationClass as the expansion indices. All entries in this table are created or deleted only by the agent. | ||||
| Rcd11IfRfNativePowerEntry | 1.3.6.1.4.1.9.9.272.1.1.2.17.1 | NA | ||
row · not-accessible · current Each entry specifies the transmit power settings of a particular radio frequency band, with a specified modulation technique, for an IEEE 802.11 radio interface. | ||||
| Ccd11IfNativeNumberPowerLevels | 1.3.6.1.4.1.9.9.272.1.1.2.17.1.1 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current The number of transmit power levels of a radio frequency band for the radio. The value of this object should be the same as the maximum cd11IfNativeTxPowerLevel of the same ifIndex, cd11IfRadioFrequencyBand, and cd11IfRadioModulationClass. If the value of this object is 0, the radio can only receive, not transmit, on this frequency band and modulation technique. | ||||
| Ccd11IfNativeCurrentPowerLevel | 1.3.6.1.4.1.9.9.272.1.1.2.17.1.2 | Unsigned32 | RW | |
column · Unsigned32 · read-write · current If cd11IfPhyNativePowerUseStandard is 'false', this object configures the current transmit power level of a radio frequency band for the radio. The value shall be one of the supported cd11IfNativeTxPowerLevel for the radio of the the same frequency band and modulation technique. For any radio does not transmit power in the specified radio frequency band and modulation technique, the value of this object is 0. | ||||
| Ccd11IfNativePowerUnits | 1.3.6.1.4.1.9.9.272.1.1.2.17.1.3 | INTEGER | RO | |
column · INTEGER · read-only · current The native transmit power units implemented on the radio. It is the units for the cd11IfNativeTxPower. For the IEEE802dot11-MIB dot11PhyTxPowerTable, 'mW' is the only supported units.
| ||||
| Tcd11IfDataRatesSensitivityTable | 1.3.6.1.4.1.9.9.272.1.1.2.18 | NA | ||
table · not-accessible · current This table specifies the receive sensitivity specifications of IEEE 802.11 radio interfaces. This table has an expansion dependent relationship on the ifTable. For each entry in this table, there exists at least an entry in the ifTable of ifType ieee80211(71). This table uses the cd11IfRadioModulationClass and IEEE802dot11-MIB dot11SupportedDataRatesRxIndex as the expansion indices. Entries in this table cannot be created or deleted by the network management system. All entries are created or deleted by the agent. | ||||
| Rcd11IfDataRatesSensitivityEntry | 1.3.6.1.4.1.9.9.272.1.1.2.18.1 | NA | ||
row · not-accessible · current Each entry specifies the receive sensitivity of an IEEE 802.11 radio interface, with a specified modulation technique, for each supported data rate identified by the dot11SupportedDataRatesRxIndex. | ||||
| Ccd11IfRatesSensRequiredSnr | 1.3.6.1.4.1.9.9.272.1.1.2.18.1.1 | Integer32 | RO | |
column · Integer32 · read-only · current The minimum SNR requirement for each data rate supported by a radio interface, when using the modulation technique specified by cd11IfRadioModulationClass. This is the required carrier to noise difference.
| ||||
| Ccd11IfRatesSensContention | 1.3.6.1.4.1.9.9.272.1.1.2.18.1.2 | Integer32 | RO | |
column · Integer32 · read-only · current The average contention sensitivity level for each data rate supported by a radio interface, when using the modulation technique specified by cd11IfRadioModulationClass. This is the value where 50% of the packets are received successfully.
| ||||
| Ncd11IfStatistics | 1.3.6.1.4.1.9.9.272.1.2 | |||
| Ncd11IfMacStatistics | 1.3.6.1.4.1.9.9.272.1.2.1 | |||
| Tcd11IfMacLayerCountersTable | 1.3.6.1.4.1.9.9.272.1.2.1.1 | NA | ||
table · not-accessible · current This table includes MAC layer statistics collected by the IEEE 802.11 radio interface. This table has a sparse dependent relationship on the ifTable. For each entry in this table, there exists an entry in the ifTable of ifType ieee80211(71). | ||||
| Rcd11IfMacLayerCountersEntry | 1.3.6.1.4.1.9.9.272.1.2.1.1.1 | NA | ||
row · not-accessible · current Each entry contains counters of frame transmissions for a radio interface.
| ||||
| Ccd11IfTransDeferEnerDetects | 1.3.6.1.4.1.9.9.272.1.2.1.1.1.1 | Counter32 | RO | |
column · Counter32 · read-only · current This counter shall increment when a frame transmission is deferred due to energy detection. | ||||
| Ccd11IfRecFrameMacCrcErrors | 1.3.6.1.4.1.9.9.272.1.2.1.1.1.2 | Counter32 | RO | |
column · Counter32 · read-only · current This counter shall increment when a frame received has any MAC CRC error. | ||||
| Ccd11IfSsidMismatches | 1.3.6.1.4.1.9.9.272.1.2.1.1.1.3 | Counter32 | RO | |
column · Counter32 · read-only · current This counter shall increment when a beacon or probe response frame received for which the SSIDs in the frame do not match the IEEE802dot11-MIB dot11DesiredSSID object. | ||||
| Tcd11IfRogueApDetectedTable | 1.3.6.1.4.1.9.9.272.1.2.1.2 | NA | ||
table · not-accessible · current This table includes rogue AP detected information collected by the IEEE 802.11 radio interface and 802.11 system management. This table has a sparse dependent relationship on the ifTable. For each entry in this table, there exists an entry in the ifTable of ifType ieee80211(71). | ||||
| Rcd11IfRogueApDetectedEntry | 1.3.6.1.4.1.9.9.272.1.2.1.2.1 | NA | ||
row · not-accessible · current Each entry contains information of a rogue AP detected by a radio interface.
| ||||
| Ccd11IfRogueApMacAddr | 1.3.6.1.4.1.9.9.272.1.2.1.2.1.1 | MacAddress | NA | |
column · MacAddress · not-accessible · current This is the MAC address of a rogue access point detected by this radio. | ||||
| Ccd11IfRogueApName | 1.3.6.1.4.1.9.9.272.1.2.1.2.1.2 | SnmpAdminString | RO | |
column · SnmpAdminString · read-only · current This is the name of the rogue access point. | ||||
| NciscoDot11IfMIBConformance | 1.3.6.1.4.1.9.9.272.3 | |||
| NciscoDot11IfMIBCompliances | 1.3.6.1.4.1.9.9.272.3.1 | |||
| MciscoDot11IfCompliance | 1.3.6.1.4.1.9.9.272.3.1.1 | deprecated | ||
compliance · deprecated The compliance statement for the cd11IfManagement, cd11IfPhyConfig, cd11IfMacStatisticsGroup, and cd11IfDomainCapabilityGroup groups. | ||||
| MciscoDot11IfComplianceRev1 | 1.3.6.1.4.1.9.9.272.3.1.2 | deprecated | ||
compliance · deprecated The compliance statement of the ciscoDot11IfMIB module. | ||||
| MciscoDot11IfComplianceRev2 | 1.3.6.1.4.1.9.9.272.3.1.3 | deprecated | ||
compliance · deprecated The compliance statement of the ciscoDot11IfMIB module.
| ||||
| MciscoDot11IfComplianceRev3 | 1.3.6.1.4.1.9.9.272.3.1.4 | deprecated | ||
compliance · deprecated The compliance statement of the ciscoDot11IfMIB module.
| ||||
| MciscoDot11IfComplianceRev4 | 1.3.6.1.4.1.9.9.272.3.1.5 | |||
compliance · current The compliance statement of the ciscoDot11IfMIB module.
| ||||
| NciscoDot11IfMIBGroups | 1.3.6.1.4.1.9.9.272.3.2 | |||
| Gcd11IfManagementGroup | 1.3.6.1.4.1.9.9.272.3.2.1 | deprecated | ||
group · deprecated Information to support management of IEEE 802.11 protocol interfaces.
| ||||
| Gcd11IfPhyConfigGroup | 1.3.6.1.4.1.9.9.272.3.2.2 | deprecated | ||
group · deprecated Information to support configuration of IEEE 802.11 protocol Physical layer. | ||||
| Gcd11IfMacStatisticsGroup | 1.3.6.1.4.1.9.9.272.3.2.3 | |||
group · current Statistics information on IEEE 802.11 radio interface MAC layer. | ||||
| Gcd11IfVlanEncryptKeyConfigGroup | 1.3.6.1.4.1.9.9.272.3.2.4 | deprecated | ||
group · deprecated WEP key configuration for specific VLANs on IEEE 802.11 radio interface. | ||||
| Gcd11IfDomainCapabilityGroup | 1.3.6.1.4.1.9.9.272.3.2.5 | deprecated | ||
group · deprecated This object class provides the objects necessary to manage the channels and transmit power usable by a radio within its regulatory domain.
| ||||
| Gcd11IfPhyMacCapabilityGroup | 1.3.6.1.4.1.9.9.272.3.2.6 | deprecated | ||
group · deprecated This object class provides the objects necessary to manage the Basic Rate capability applied to the defined operational data rate and and IEEE 802.11 Standard applied to the radio. | ||||
| Gcd11IfAuthAlgMethodListGroup | 1.3.6.1.4.1.9.9.272.3.2.7 | deprecated | ||
group · deprecated This object class provides the objects necessary to specify the authentication method applied to MAC address or EAP authentications. | ||||
| Gcd11IfRadioManageGroup | 1.3.6.1.4.1.9.9.272.3.2.8 | deprecated | ||
group · deprecated Information to manage IEEE 802.11 protocol radio interface settings.
| ||||
| Gcd11IfAssociationManageGroup | 1.3.6.1.4.1.9.9.272.3.2.9 | |||
group · current Information to manage IEEE 802.11 protocol interface desired SSID association and default encryption key settings. | ||||
| Gcd11IfSsidAssociationGroup | 1.3.6.1.4.1.9.9.272.3.2.10 | |||
group · current Information to manage IEEE 802.11 protocol interface SSID association and authentication settings.
| ||||
| Gcd11IfVlanManageGroup | 1.3.6.1.4.1.9.9.272.3.2.11 | |||
group · current Information to manage IEEE 802.11 protocol interface VLAN and encryption settings.
| ||||
| Gcd11IfRemoteMonitoringGroup | 1.3.6.1.4.1.9.9.272.3.2.12 | |||
group · current Information to manage IEEE 802.11 protocol interface remote radio monitoring settings. | ||||
| Gcd11IfPhyConfigGroupRev1 | 1.3.6.1.4.1.9.9.272.3.2.13 | |||
group · current Information to configure IEEE 802.11 protocol Physical layer settings.
| ||||
| Gcd11IfPhyErpConfigGroup | 1.3.6.1.4.1.9.9.272.3.2.14 | |||
group · current Information to configure IEEE 802.11g protocol Physical layer settings. | ||||
| Gcd11IfVlanWepManageGroup | 1.3.6.1.4.1.9.9.272.3.2.15 | |||
group · current Information to manage IEEE 802.11 protocol interface VLAN WEP encryption settings. | ||||
| Gcd11IfRogueApDetectedGroup | 1.3.6.1.4.1.9.9.272.3.2.16 | |||
| Gcd11IfStationManageGroup | 1.3.6.1.4.1.9.9.272.3.2.17 | |||
group · current Information to manage IEEE 802.11 protocol radio interface settings.
| ||||
| Gcd11IfNativeRadioManageGroup | 1.3.6.1.4.1.9.9.272.3.2.18 | |||
group · current Native parameters to manage IEEE 802.11 radio power and frequency bands.
| ||||
| Gcd11IfDataRatesSensitivityGroup | 1.3.6.1.4.1.9.9.272.3.2.19 | |||
group · current Receive sensitivity specification for IEEE 802.11 radios. | ||||
| Gcd11IfMonitorNotificationGroup | 1.3.6.1.4.1.9.9.272.3.2.20 | |||
group · current The notification group for this module. | ||||
| Gcd11Ifdot11UpgradeStatusGroup | 1.3.6.1.4.1.9.9.272.3.2.21 | |||
group · current This collection of objects provide information about the status of upgrade of the dot11 radios to operate in the new frequency set.
| ||||
| Gcd11Ifdot11MobileStationScanGroup | 1.3.6.1.4.1.9.9.272.3.2.22 | |||
group · current This collection of objects provide information about the limited channel to scan and Ignore List. | ||||
Textual conventions
CDot11IfCipherTypeBitsaesccm(5)ckip(0)cmic(1)tkip(2)wep128(4)wep40(3)These are the frame encryption cipher types for frames on IEEE 802.11 radio interfaces. ckip Cisco Per packet key hashing, cmic Cisco MMH MIC, tkip WPA Temporal Key encryption, wep40 40-bit WEP key, wep128 128-bit WEP key, aesccm WPA AES CCMP encryption.CDot11IfMicAlgorithmINTEGERmicMXX(2)micMichael(3)micNone(1)Auxiliary MIC calculated on WEP-encoded packets to validate that they have not been modified. This is in addition to the standard 802.11 ICV. The two options are: micNone(1) - do not apply MIC, micMXX(2) - apply MMH MIC, micMichael(3) - Michael MIC.CDot11IfVlanIdOrZeroUnsigned32 (0..4095)This is a 12-bit VLAN ID used in the VLAN Tag header. A value of '0' indicates NULL or no VLAN ID. and '4095' is the default VLAN for Cisco VoIP Phones. This textual convention differs from the VlanId textual convention, defined by the Q-BRIDGE-MIB in RFC-2674, because VlanId does not permit the value '0' and '4095'.
CDot11IfWepKeyPermuteAlgorithmINTEGERwepPermuteIV(2)wepPermuteNone(1)This defines the function through which the WEP encryption key is permuted between key renewal periods. wepPermuteNone(1) - no WEP key permutation, wepPermuteIV(2) - WEP key permutation with initialization vector.CDot11RadioFrequencyBandTypeBitscept(4)ism24G(0)japan49G(5)japan50G(6)unii1(1)unii2(2)unii3(3)These are the radio frequency band names the IEEE 802.11 radio is operating on: ism24G(0) - ISM 2.4 GHz band, unii1(1) - U-NII-1 band (5.15-5.25 GHz), unii2(2) - U-NII-2 band (5.25-5.35 GHz), unii3(3) - U-NII-3 band (5.725-5.825 GHz), cept(4) - CEPT band B (5.47-5.725 GHz), japan49G(5) - Japan 4.9 band (4.9-5.0 GHz), japan50G(6) - Japan 5.0 band (5.03-5.091 GHz).CDot11RadioModulationClassINTEGERdsss(1)ofdm(2)These are classifications of radio modulation techniques used by the various Physical Layers of IEEE 802.11 radios: dsss(1) - modulation schemes associated with DSSS type PHYs, ofdm(2) - modulation schemes associated with OFDM type PHYs.Cd11IfDot11UpgradeStatusINTEGERunknown(1)upgradeDone(5)upgradeNotApplicable(2)upgradeNotDone(3)upgradeNotNeeded(4)These are the various status on the Radio Upgrade: unknown(1) - upgrade status unknown, upgradeNotApplicable(2) - Regulatory domain upgrade is not applicable for 11b/g radios and 11a radios not in Japan regulatory domain, upgradeNotDone(3) - 11a radio is in Japan domain but yet to be upgraded, upgradeNotNeeded(4) - 11a radio is already configured to operate in the W52 domain and that the upgrade is not needed, upgradeDone(5) - upgrade has been done from J52 to W52.WepKeyType128OCTET STRING (SIZE (5..13))WEP shared secret encryption key, 128-bits or 16 octets. Only the first 13 octets are accessible to users among the total 16 octets.
Traps / Notifications
- cd11IfRogueApDetectedNotif
1.3.6.1.4.1.9.9.272.0.2 - cd11IfStationSwitchOverNotif
1.3.6.1.4.1.9.9.272.0.1
Groups and compliance
- cd11IfAssociationManageGroup
- cd11IfAuthAlgMethodListGroup
- cd11IfDataRatesSensitivityGroup
- cd11IfDomainCapabilityGroup
- cd11IfMacStatisticsGroup
- cd11IfManagementGroup
- cd11IfMonitorNotificationGroup
- cd11IfNativeRadioManageGroup
- cd11IfPhyConfigGroup
- cd11IfPhyConfigGroupRev1
- cd11IfPhyErpConfigGroup
- cd11IfPhyMacCapabilityGroup
- cd11IfRadioManageGroup
- cd11IfRemoteMonitoringGroup
- cd11IfRogueApDetectedGroup
- cd11IfSsidAssociationGroup
- cd11IfStationManageGroup
- cd11IfVlanEncryptKeyConfigGroup
- cd11IfVlanManageGroup
- cd11IfVlanWepManageGroup
- cd11Ifdot11MobileStationScanGroup
- cd11Ifdot11UpgradeStatusGroup
- ciscoDot11IfCompliance
- ciscoDot11IfComplianceRev1
- ciscoDot11IfComplianceRev2
- ciscoDot11IfComplianceRev3
- ciscoDot11IfComplianceRev4