CISCO-DOT11-ASSOCIATION-MIB
ciscoSystemsThis MIB module provides network management
information on IEEE 802.11 wireless device
association management and data packet forwarding
configuration and statistics. This MIB is an
extension to the IEEE802dot11-MIB and provides
per client based information.
The IEEE802dot11-MIB is defined in the IEEE Std
802.11-Jan 14 1999, Wireless LAN Medium Access
Control and Physical Layer Specifications, by the
LAN MAN Standards Committee of the IEEE Computer
Society.
GLOSSARY and ACRONYMS
Access point (AP)
Transmitter/receiver (transceiver) device
that commonly connects and transports data
between a wireless network and a wired network.
AES
Advanced Encryption Standard
Association
The service used to establish access point
or station mapping and enable STA invocation
of the distribution system serivces.
(Wireless clients attempt to connect to
access points.)
Bridge
Device that connects two or more segments
and reduces traffic by analyzing the
destination address, filtering the frame,
and forwarding the frame to all connected
segments.
Bridge AP
It is an AP that functions as a transparent
bridge between 2 wired LAN segments.
Bridge Host
This is also known as Work Group Bridge. This
is a non-root bridge that is connected to a
remote LAN segment and will only communicate
with repeaters or root bridges. It does not
accept association from other wireless devices.
BSS
IEEE 802.11 Basic Service Set (Radio Cell). The
BSS of an AP comprises of the stations directly
associated with the AP.
CCX
Cisco Compatible eXtensions
A set of specifications which when implemented
would make a client radio interoperable with a
Cisco WLAN infrastructure and make best use of the
innovations for enhanced security, mobility,
quality of service and network management.
CCMP
Code Mode/CBC Mac Protocol
Client (Client Station)
A wireless device in a wireless network
associated with an access point.
Direct Sequence Spread Sprectrum ( DSSS )
DSSS is a method to send data where the
transmitting and receiving systems operate at
frequencies as wide as 22MHz. The wide channels
help the participating systems to send more
information at higher data rates than the FSSS
systems.
EAP
Extensible Authentication Protocol
EAP-TLS
Extensible Authentication Protocol-Transport
Layer Security
Frequency Hopping Spread Spectrum ( FSSS )
FSSS systems hop from one frequency to another in
the allowed band of frequencies during the data
transmission. 83 MHz is specified as the allowed
band of frequencies in the 2.4 GHz spectrum.
IEEE 802.11
Standard to encourage interoperability among
wireless networking equipment.
IEEE 802.11b
The IEEE 802.11b standard describes DSSS systems
that operate in the 2.4 GHz ISM band at data
rates of 1, 2, 5,5 and 11 Mbps.
IEEE 802.11a
The IEEE 802.11a standard describes wireless LAN
operation in the 5 GHz UNII band at data rates
of 6, 9, 12, 18, 24, 36, 48 and 54 Mbps.
IEEE 802.11g
This standard specifies operation in 2.4 GHz ISM
band at data rates of 6, 9, 12, 18. 24, 36, 48 and
54 Mbps.
Industrial, Scientific and Medical band (ISM)
A license-free band specified by the Federal
Communications Commission for use by the wireless
LAN systems. The ISM bands are located starting
at 902 MHz, 2.4GHz and 5.8 GHz.
MIC
Message Integrity Check. A MIC can, optionally,
be added to WEP-encrypted 802.11 frames.
Non-Root Bridge
This wireless bridge does not connect to the main
wired LAN segment. It connects to a remote wired
LAN segment and can associate to root bridges and
other non-root bridges that accept client
associations. It also can accept associations
from other non-root bridges, repeater access
points, and client devices.
PCI
Peripheral Component Interconnect
A local bus standard developed by Intel
Corporation. Most modern PCs include a PCI bus.
PCI is a 64-bit bus, though it is usually
implemented as a 32-bit bus. It can run at clock
speeds of 33 or 66 MHz. At 32 bits and 33 MHz, it
yields a throughput rate of 133 MBps.
Repeater
Device that connects multiple segments, listening
to each and repeating signal on one to every other
connected one; regenerates each transmission
so that it can travel farther.
Repeater or Non-root Access Point
The repeater access point is not connected
to the wired LAN. The Repeater is a wireless
LAN transceiver that transfers data between
a client and another access point, another
repeater, or between two bridges. The repeater
is placed within radio range of an access point
connected to the wired LAN, another repeater, or
an non-root bridge to extend the range of the
infrastructure.
Root Access Point
This access point connects clients to the main
wired LAN.
Root Wireless Bridge
This wireless bridge is connected to the main
wired LAN. This wireless bridge can communicate
with non-root wireless bridges, repeater access
points, and client devices but not with another
wireless root bridge. Only one wireless bridge
in a wireless LAN can be set as the wireless
root bridge.
SSID
Radio Service Set ID. It is used for identification
during association.
STA (WSTA)
A non-AP 802.11 wireless station.
TKIP
WPA Temporal Key encryption.
Unlicensed National Information Infrastucture (UNII)
The UNII bands are in the 5 GHz range and are 100
MHz wide. These bands are used by 802.11a-compliant
devices.
WEP
Wired Equivalent Privacy. 'WEP' is generally used
to refer to 802.11 encryption.
WPA
WiFi Protected Access
Work Group Bridges (WGB)
See bridge host.snmptranslate -m CISCO-DOT11-ASSOCIATION-MIB -Tpsnmpwalk -v2c -c <community> -m CISCO-DOT11-ASSOCIATION-MIB <host> 1.3.6.1.4.1.9.9.273Imports
| CISCO-DOT11-IF-MIB | CDot11IfCipherType, CDot11IfVlanIdOrZero, cd11IfAuxSsid |
|---|---|
| CISCO-SMI | ciscoMgmt |
| IF-MIB | InterfaceIndex, ifIndex |
| INET-ADDRESS-MIB | InetAddress, InetAddressType |
| SNMP-FRAMEWORK-MIB | SnmpAdminString |
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP |
| SNMPv2-SMI | Bits, Counter32, Gauge32, Integer32, IpAddress, MODULE-IDENTITY, MibIdentifier, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, iso |
| SNMPv2-TC | DisplayString, MacAddress, PhysAddress, TEXTUAL-CONVENTION, TruthValue |
OID tree
| Name | OID | Type | Access | Status |
|---|---|---|---|---|
| IciscoDot11AssociationMIB | 1.3.6.1.4.1.9.9.273 | |||
identity This MIB module provides network management
information on IEEE 802.11 wireless device
association management and data packet forwarding
configuration and statistics. This MIB is an
extension to the IEEE802dot11-MIB and provides
per client based information.
The IEEE802dot11-MIB is defined in the IEEE Std
802.11-Jan 14 1999, Wireless LAN Medium Access
Control and Physical Layer Specifications, by the
LAN MAN Standards Committee of the IEEE Computer
Society.
GLOSSARY and ACRONYMS
Access point (AP)
Transmitter/receiver (transceiver) device
that commonly connects and transports data
between a wireless network and a wired network.
AES
Advanced Encryption Standard
Association
The service used to establish access point
or station mapping and enable STA invocation
of the distribution system serivces.
(Wireless clients attempt to connect to
access points.)
Bridge
Device that connects two or more segments
and reduces traffic by analyzing the
destination address, filtering the frame,
and forwarding the frame to all connected
segments.
Bridge AP
It is an AP that functions as a transparent
bridge between 2 wired LAN segments.
Bridge Host
This is also known as Work Group Bridge. This
is a non-root bridge that is connected to a
remote LAN segment and will only communicate
with repeaters or root bridges. It does not
accept association from other wireless devices.
BSS
IEEE 802.11 Basic Service Set (Radio Cell). The
BSS of an AP comprises of the stations directly
associated with the AP.
CCX
Cisco Compatible eXtensions
A set of specifications which when implemented
would make a client radio interoperable with a
Cisco WLAN infrastructure and make best use of the
innovations for enhanced security, mobility,
quality of service and network management.
CCMP
Code Mode/CBC Mac Protocol
Client (Client Station)
A wireless device in a wireless network
associated with an access point.
Direct Sequence Spread Sprectrum ( DSSS )
DSSS is a method to send data where the
transmitting and receiving systems operate at
frequencies as wide as 22MHz. The wide channels
help the participating systems to send more
information at higher data rates than the FSSS
systems.
EAP
Extensible Authentication Protocol
EAP-TLS
Extensible Authentication Protocol-Transport
Layer Security
Frequency Hopping Spread Spectrum ( FSSS )
FSSS systems hop from one frequency to another in
the allowed band of frequencies during the data
transmission. 83 MHz is specified as the allowed
band of frequencies in the 2.4 GHz spectrum.
IEEE 802.11
Standard to encourage interoperability among
wireless networking equipment.
IEEE 802.11b
The IEEE 802.11b standard describes DSSS systems
that operate in the 2.4 GHz ISM band at data
rates of 1, 2, 5,5 and 11 Mbps.
IEEE 802.11a
The IEEE 802.11a standard describes wireless LAN
operation in the 5 GHz UNII band at data rates
of 6, 9, 12, 18, 24, 36, 48 and 54 Mbps.
IEEE 802.11g
This standard specifies operation in 2.4 GHz ISM
band at data rates of 6, 9, 12, 18. 24, 36, 48 and
54 Mbps.
Industrial, Scientific and Medical band (ISM)
A license-free band specified by the Federal
Communications Commission for use by the wireless
LAN systems. The ISM bands are located starting
at 902 MHz, 2.4GHz and 5.8 GHz.
MIC
Message Integrity Check. A MIC can, optionally,
be added to WEP-encrypted 802.11 frames.
Non-Root Bridge
This wireless bridge does not connect to the main
wired LAN segment. It connects to a remote wired
LAN segment and can associate to root bridges and
other non-root bridges that accept client
associations. It also can accept associations
from other non-root bridges, repeater access
points, and client devices.
PCI
Peripheral Component Interconnect
A local bus standard developed by Intel
Corporation. Most modern PCs include a PCI bus.
PCI is a 64-bit bus, though it is usually
implemented as a 32-bit bus. It can run at clock
speeds of 33 or 66 MHz. At 32 bits and 33 MHz, it
yields a throughput rate of 133 MBps.
Repeater
Device that connects multiple segments, listening
to each and repeating signal on one to every other
connected one; regenerates each transmission
so that it can travel farther.
Repeater or Non-root Access Point
The repeater access point is not connected
to the wired LAN. The Repeater is a wireless
LAN transceiver that transfers data between
a client and another access point, another
repeater, or between two bridges. The repeater
is placed within radio range of an access point
connected to the wired LAN, another repeater, or
an non-root bridge to extend the range of the
infrastructure.
Root Access Point
This access point connects clients to the main
wired LAN.
Root Wireless Bridge
This wireless bridge is connected to the main
wired LAN. This wireless bridge can communicate
with non-root wireless bridges, repeater access
points, and client devices but not with another
wireless root bridge. Only one wireless bridge
in a wireless LAN can be set as the wireless
root bridge.
SSID
Radio Service Set ID. It is used for identification
during association.
STA (WSTA)
A non-AP 802.11 wireless station.
TKIP
WPA Temporal Key encryption.
Unlicensed National Information Infrastucture (UNII)
The UNII bands are in the 5 GHz range and are 100
MHz wide. These bands are used by 802.11a-compliant
devices.
WEP
Wired Equivalent Privacy. 'WEP' is generally used
to refer to 802.11 encryption.
WPA
WiFi Protected Access
Work Group Bridges (WGB)
See bridge host. | ||||
| NciscoDot11AssocMIBObjects | 1.3.6.1.4.1.9.9.273.1 | |||
| NcDot11AssociationGlobal | 1.3.6.1.4.1.9.9.273.1.1 | |||
| ScDot11ParentAddress | 1.3.6.1.4.1.9.9.273.1.1.1 | MacAddress | RO | |
scalar · MacAddress · read-only · current This is the MAC address of the parent access point or root bridge for this device. The value is zero if this is a root access point or bridge. | ||||
| TcDot11ActiveDevicesTable | 1.3.6.1.4.1.9.9.273.1.1.2 | NA | ||
table · not-accessible · current This table contains the list of active devices currently associated with this device on each of the IEEE 802.11 interfaces. This table has a sparse dependent relationship on the ifTable. | ||||
| RcDot11ActiveDevicesEntry | 1.3.6.1.4.1.9.9.273.1.1.2.1 | NA | ||
row · not-accessible · current An entry represents a currently active device associated with this device. These active devices include: wireless clients, repeaters, and bridges.
| ||||
| CcDot11ActiveWirelessClients | 1.3.6.1.4.1.9.9.273.1.1.2.1.1 | Gauge32 (0..2007) | RO | |
column · Gauge32 (0..2007) · read-only · current This is the number of wireless clients currently associating with this device on this interface.
| ||||
| CcDot11ActiveBridges | 1.3.6.1.4.1.9.9.273.1.1.2.1.2 | Gauge32 (0..2007) | RO | |
column · Gauge32 (0..2007) · read-only · current This is the number of bridges currently associating with this device on this interface.
| ||||
| CcDot11ActiveRepeaters | 1.3.6.1.4.1.9.9.273.1.1.2.1.3 | Gauge32 (0..2007) | RO | |
column · Gauge32 (0..2007) · read-only · current This is the number of repeaters currently associating with this device on this interface.
| ||||
| TcDot11AssociationStatsTable | 1.3.6.1.4.1.9.9.273.1.1.3 | NA | ||
table · not-accessible · current This table contains statistics for various devices associated with this device on each of the IEEE 802.11 interfaces since it was last re-started. These devices include: wireless clients, repeaters, and bridges. This table has a sparse dependent relationship on the ifTable. | ||||
| RcDot11AssociationStatsEntry | 1.3.6.1.4.1.9.9.273.1.1.3.1 | NA | ||
row · not-accessible · current Each entry provides association statistics of various devices interacting with this device on each of the IEEE 802.11 interfaces.
| ||||
| CcDot11AssStatsAssociated | 1.3.6.1.4.1.9.9.273.1.1.3.1.1 | Counter32 | RO | |
column · Counter32 · read-only · current This object counts the number of stations associated with this device on this interface since device re-started.
| ||||
| CcDot11AssStatsAuthenticated | 1.3.6.1.4.1.9.9.273.1.1.3.1.2 | Counter32 | RO | |
column · Counter32 · read-only · current This object counts the number of stations authenticated with this device on this interface since device re-started.
| ||||
| CcDot11AssStatsRoamedIn | 1.3.6.1.4.1.9.9.273.1.1.3.1.3 | Counter32 | RO | |
column · Counter32 · read-only · current This object counts the number of stations roamed from another device to this device on this interface since device re-started.
| ||||
| CcDot11AssStatsRoamedAway | 1.3.6.1.4.1.9.9.273.1.1.3.1.4 | Counter32 | RO | |
column · Counter32 · read-only · current This object counts the number of stations roamed away from this device on this interface since device re-started.
| ||||
| CcDot11AssStatsDeauthenticated | 1.3.6.1.4.1.9.9.273.1.1.3.1.5 | Counter32 | RO | |
column · Counter32 · read-only · current This object counts the number of stations deauthenticated with this device on this interface since device re-started.
| ||||
| CcDot11AssStatsDisassociated | 1.3.6.1.4.1.9.9.273.1.1.3.1.6 | Counter32 | RO | |
column · Counter32 · read-only · current This object counts the number of stations disassociated with this device on this interface since device re-started.
| ||||
| Tcd11IfCipherStatsTable | 1.3.6.1.4.1.9.9.273.1.1.4 | NA | ||
table · not-accessible · current This table includes AES, TKIP, and security tempering attempts statistics collected by the IEEE 802.11 radio interfaces and system management. This table has a sparse dependent relationship on the ifTable. For each entry in this table, there exists an entry in the ifTable of ifType ieee80211(71). | ||||
| Rcd11IfCipherStatsEntry | 1.3.6.1.4.1.9.9.273.1.1.4.1 | NA | ||
row · not-accessible · current Each entry provides cipher related statistics collected on each of the IEEE 802.11 interfaces.
| ||||
| Ccd11IfCipherMicFailClientAddress | 1.3.6.1.4.1.9.9.273.1.1.4.1.1 | MacAddress | RO | |
column · MacAddress · read-only · current This is MAC address of the client attached to this radio interface that caused the most recent MIC failure. | ||||
| Ccd11IfCipherTkipLocalMicFailures | 1.3.6.1.4.1.9.9.273.1.1.4.1.2 | Counter32 | RO | |
column · Counter32 · read-only · current This object counts the number of MIC failures encountered on this radio interface since device re-started. | ||||
| Ccd11IfCipherTkipRemotMicFailures | 1.3.6.1.4.1.9.9.273.1.1.4.1.3 | Counter32 | RO | |
column · Counter32 · read-only · current This object counts the number of MIC failures reported by clients on this radio interface since device re-started. | ||||
| Ccd11IfCipherTkipCounterMeasInvok | 1.3.6.1.4.1.9.9.273.1.1.4.1.4 | Counter32 | RO | |
column · Counter32 · read-only · current This object counts the number of TKIP Counter Measures invoked on this interface since device re-started. | ||||
| Ccd11IfCipherCcmpReplaysDiscarded | 1.3.6.1.4.1.9.9.273.1.1.4.1.5 | Counter32 | RO | |
column · Counter32 · read-only · current This object counts the number of received unicast fragments discarded by replay mechanism on this interface since device re-started. | ||||
| Ccd11IfCipherTkipReplaysDetected | 1.3.6.1.4.1.9.9.273.1.1.4.1.6 | Counter32 | RO | |
column · Counter32 · read-only · current This object counts the number of TKIP replay errors detected on this interface since device re-started. | ||||
| NcDot11ClientConfiguration | 1.3.6.1.4.1.9.9.273.1.2 | |||
| TcDot11ClientConfigInfoTable | 1.3.6.1.4.1.9.9.273.1.2.1 | NA | ||
table · not-accessible · current This table contains configuration information of client devices. Entries on this table are created by the device radio driver when clients establish association with the device. Entries are removed when clients disassociate with the device. These clients include: wireless clients, repeaters, and bridges. On Infrastructure clients like repeaters, non-root bridges and workgroup bridges, this table also has an entry for the parent device they are associated to. | ||||
| RcDot11ClientConfigInfoEntry | 1.3.6.1.4.1.9.9.273.1.2.1.1 | NA | ||
row · not-accessible · current Each entry is the device specification of a client of this device on the IEEE 802.11 radio interfaces. Clients are grouped according to the SSIDs of the interfaces they use for associations and the MAC address of their parent devices if the clients are repeat APs. | ||||
| CcDot11ClientAddress | 1.3.6.1.4.1.9.9.273.1.2.1.1.1 | MacAddress | NA | |
column · MacAddress · not-accessible · current The MAC address of the client. | ||||
| CcDot11ClientParentAddress | 1.3.6.1.4.1.9.9.273.1.2.1.1.2 | MacAddress | RO | |
column · MacAddress · read-only · current The MAC address of the parent of the client if the client is a repeater AP. If this client has no parent, the value is '00000000'h. | ||||
| CcDot11ClientRoleClassType | 1.3.6.1.4.1.9.9.273.1.2.1.1.3 | CDot11ClientRoleClassType | RO | |
column · CDot11ClientRoleClassType · read-only · current The role classification of the client. | ||||
| CcDot11ClientDevType | 1.3.6.1.4.1.9.9.273.1.2.1.1.4 | CDot11ClientDevType | RO | |
column · CDot11ClientDevType · read-only · current The device type of the client. | ||||
| CcDot11ClientRadioType | 1.3.6.1.4.1.9.9.273.1.2.1.1.5 | CDot11ClientRadioType | RO | |
column · CDot11ClientRadioType · read-only · current The radio classification of the client. | ||||
| CcDot11ClientWepEnabled | 1.3.6.1.4.1.9.9.273.1.2.1.1.6 | TruthValue | RO | |
column · TruthValue · read-only · current When this object is 'true', it indicates that the WEP key mechanism is used for transmitting frames of data for this client. The default value of this object is 'false'. | ||||
| CcDot11ClientWepKeyMixEnabled | 1.3.6.1.4.1.9.9.273.1.2.1.1.7 | TruthValue | RO | |
column · TruthValue · read-only · current When this object is 'true', it indicates that this client is using WEP key mixing. | ||||
| CcDot11ClientMicEnabled | 1.3.6.1.4.1.9.9.273.1.2.1.1.8 | TruthValue | RO | |
column · TruthValue · read-only · current When this object is 'true', it indicates that the MIC is enabled for this client. The default value of this object is 'false'. | ||||
| CcDot11ClientPowerSaveMode | 1.3.6.1.4.1.9.9.273.1.2.1.1.9 | INTEGER | RO | |
column · INTEGER · read-only · current The power management mode of this client. The
two possible modes are:
active(1) - this client is not in power-save
mode and it is actively sending or
receiving data.
powersave(2) - this client is in power-save mode and
it wakes up once a while to check for
pending data.
| ||||
| CcDot11ClientAid | 1.3.6.1.4.1.9.9.273.1.2.1.1.10 | Unsigned32 (0..2008) | RO | |
column · Unsigned32 (0..2008) · read-only · current This is the association identification number of clients or multicast addresses associating with this device. For a multicast address with clients, the cDot11ClientAid is '0'. For the uplink association from this device to its parent access point, the cDot11ClientAid is always '1'. For any multicast address with no client currently known to be associated with this device, the cDot11ClientAid is '2008'. | ||||
| CcDot11ClientDataRateSet | 1.3.6.1.4.1.9.9.273.1.2.1.1.11 | OCTET STRING (SIZE (1..126)) | RO | |
column · OCTET STRING (SIZE (1..126)) · read-only · current This is the set of data rates at which this client can transmit and receive data. Each client can support up to 126 rates. Each octet contains an integer value representing one of these 126 rates. Each rate shall be within the range from 2 to 127, corresponding to data rates in increments of 500 kb/s from 1 Mb/s to 63.5 Mb/s, This value is reported in transmitted Beacon, Probe Request, Probe Response, Association Request, Association Response, Reassociation Request, and Reassociation Response frames, and is used to determine whether a BSS with which the client desires to synchronize is suitable. It is also used when starting a BSS. | ||||
| CcDot11ClientSoftwareVersion | 1.3.6.1.4.1.9.9.273.1.2.1.1.12 | SnmpAdminString | RO | |
column · SnmpAdminString · read-only · current This is the Cisco IOS software version if the other end of the association is a bridge, access point, or repeater. If it is a wireless client, this is the firmware version of the client card. | ||||
| CcDot11ClientName | 1.3.6.1.4.1.9.9.273.1.2.1.1.13 | SnmpAdminString | RO | |
column · SnmpAdminString · read-only · current This is the Cisco IOS device hostname if the other end of the association is a bridge, access point, or repeater. If it is a wireless client, this is the configured client name. | ||||
| CcDot11ClientAssociationState | 1.3.6.1.4.1.9.9.273.1.2.1.1.14 | INTEGER | RO | |
column · INTEGER · read-only · current This object indicates the state of the authentication
and association process between the two parties:
initial(1) - association request
received from client,
authenNotAssociated(2) - 802.11 authenticated but
not 802.11 associated,
assocAndAuthenticated(3) - 802.11 associated and
802.1x authenticated,
assocNotAnuthenticated(4) - 802.11 associated but
802.1x not
authenticated.
| ||||
| CcDot11ClientIpAddressType | 1.3.6.1.4.1.9.9.273.1.2.1.1.15 | InetAddressType | RO | |
column · InetAddressType · read-only · current This is the IP address type of the cDot11ClientIpAddress. | ||||
| CcDot11ClientIpAddress | 1.3.6.1.4.1.9.9.273.1.2.1.1.16 | InetAddress | RO | |
column · InetAddress · read-only · current This is the static or DHCP assigned IP address of the client. | ||||
| CcDot11ClientVlanId | 1.3.6.1.4.1.9.9.273.1.2.1.1.17 | CDot11IfVlanIdOrZero | RO | |
column · CDot11IfVlanIdOrZero · read-only · current This is the VLAN which this wireless client is assigned to when it is successfully associated to the wireless station. The value is 0 if this wireless client is not assigned to any VLAN or this wireless station is not configured with any VLAN. | ||||
| CcDot11ClientSubIfIndex | 1.3.6.1.4.1.9.9.273.1.2.1.1.18 | InterfaceIndex | RO | |
column · InterfaceIndex · read-only · current This is the ifIndex of the sub-interface which this wireless client is assigned to when it is successfully associated to the wireless station. The value of this object is 0, if this wireless station is not configured with VLAN and this wireless client is assigned to the radio hardware interface of this wireless station. | ||||
| CcDot11ClientAuthenAlgorithm | 1.3.6.1.4.1.9.9.273.1.2.1.1.19 | CDot11AuthenticationMethod | RO | |
column · CDot11AuthenticationMethod · read-only · current This is the IEEE 802.11 authentication methods performed between the wireless station and this client during association. | ||||
| CcDot11ClientAdditionalAuthen | 1.3.6.1.4.1.9.9.273.1.2.1.1.20 | CDot11AdditionalAuthenMethod | RO | |
column · CDot11AdditionalAuthenMethod · read-only · current These are the additional authentications that were performed after IEEE 802.11 Open System or Shared Key authentication had completed. If none of the bits is set, no additional MAC address or EAP authentication was performed during association. | ||||
| CcDot11ClientDot1xAuthenAlgorithm | 1.3.6.1.4.1.9.9.273.1.2.1.1.21 | CDot11Dot1xAuthenMethod | RO | |
column · CDot11Dot1xAuthenMethod · read-only · current This the IEEE 802.1x authentication methods performed between this wireless client and the authentication server. If none of the bits is set, no IEEE 802.1x authentication was performed during association. | ||||
| CcDot11ClientKeyManagement | 1.3.6.1.4.1.9.9.273.1.2.1.1.22 | CDot11KeyManagementMethod | RO | deprecated |
column · CDot11KeyManagementMethod · read-only · deprecated This is the encryption key management methods employed by this client for IEEE 802.11 wireless frame encryption. If none of the bits is set, no key management method is employed. | ||||
| CcDot11ClientUnicastCipher | 1.3.6.1.4.1.9.9.273.1.2.1.1.23 | CDot11IfCipherType | RO | |
column · CDot11IfCipherType · read-only · current These are all the possible unicast data frame cipher
encryption type combinations currently supported on
this IEEE 802.11 client. If none of the bits is set,
the client is not performing any unicast data frame
encryption.
aesccm WPA AES CCMP encryption,
ckip Cisco Per packet key hashing,
cmic Cisco MMH MIC,
ckip|cmic Cisco Per packet key hashing and
Cisco MMH MIC,
tkip WPA Temporal Key encryption,
wep128 128-bit WEP key,
wep40 40-bit WEP key.
tkip|wep128 WPA Temporal Key and 128-bit WEP,
tkip|wep40 WPA Temporal Key and 40-bit WEP. | ||||
| CcDot11ClientMulticastCipher | 1.3.6.1.4.1.9.9.273.1.2.1.1.24 | CDot11IfCipherType | RO | |
column · CDot11IfCipherType · read-only · current These are all the possible multi-cast data frame
cipher encryption type combinations currently supported
on this IEEE 802.11 client. If none of the bits is set,
the client is not performing any multi-cast data frame
encryption.
aesccm WPA AES CCMP encryption,
ckip Cisco Per packet key hashing,
cmic Cisco MMH MIC,
ckip|cmic Cisco Per packet key hashing and
Cisco MMH MIC,
tkip WPA Temporal Key encryption,
wep128 128-bit WEP key,
wep40 40-bit WEP key.
tkip|wep128 WPA Temporal Key and 128-bit WEP,
tkip|wep40 WPA Temporal Key and 40-bit WEP. | ||||
| CcDot11ClientDevObjectID | 1.3.6.1.4.1.9.9.273.1.2.1.1.25 | OBJECT IDENTIFIER | RO | |
column · OBJECT IDENTIFIER · read-only · current This object indicates the authoritative identification of the associated 802.11 client as assigned by the respective vendor. A value of '0.0' shall be populated if no such identification exists for this 802.11 client. | ||||
| CcDot11ClientNewKeyManagement | 1.3.6.1.4.1.9.9.273.1.2.1.1.26 | CDot11NewKeyManagementMethod | RO | |
column · CDot11NewKeyManagementMethod · read-only · current This is the encryption key management methods employed by this client for IEEE 802.11 wireless frame encryption. If none of the bits is set, no key management method is employed. | ||||
| NcDot11ClientStatistics | 1.3.6.1.4.1.9.9.273.1.3 | |||
| TcDot11ClientStatisticTable | 1.3.6.1.4.1.9.9.273.1.3.1 | NA | ||
table · not-accessible · current This table contains statistics and status of all clients on the cDot11ClientConfigInfoTable. This table has a one-to-one relationship with the cDot11ClientConfigInfoTable. | ||||
| RcDot11ClientStatisticEntry | 1.3.6.1.4.1.9.9.273.1.3.1.1 | NA | ||
row · not-accessible · current Each entry contains statistics about errors, data transmitting and receiving rates and counts information of a client.
| ||||
| CcDot11ClientCurrentTxRateSet | 1.3.6.1.4.1.9.9.273.1.3.1.1.1 | OCTET STRING (SIZE (1..126)) | RO | |
column · OCTET STRING (SIZE (1..126)) · read-only · current This is the set current transmit data rates for this client. Each client can transmit data at all of its configured rates. There is a maximum of 126 it can configure to transmit. Each octet contains an integer value representing one of these 126 rates it is currently transmitting. Each rate shall be within the range from 2 to 127, corresponding to data rates in increments of 500 kb/s from 1 Mb/s to 63.5 Mb/s. This value is reported in transmitted Beacon, Probe Request, Probe Response, Association Request, Association Response, Reassociation Request, and Reassociation Response frames. | ||||
| CcDot11ClientUpTime | 1.3.6.1.4.1.9.9.273.1.3.1.1.2 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current The time in seconds that this client has been associated with this device.
| ||||
| CcDot11ClientSignalStrength | 1.3.6.1.4.1.9.9.273.1.3.1.1.3 | Integer32 (-100..0) | RO | |
column · Integer32 (-100..0) · read-only · current This is a device-dependent measure of the signal strength of the most recently received packet from this client. It may be normalized or unnormalized.
| ||||
| CcDot11ClientSigQuality | 1.3.6.1.4.1.9.9.273.1.3.1.1.4 | Unsigned32 (0..100) | RO | |
column · Unsigned32 (0..100) · read-only · current This is a device-dependent measure of the signal quality of the most recently received packet from this client.
| ||||
| CcDot11ClientAgingLeft | 1.3.6.1.4.1.9.9.273.1.3.1.1.5 | Gauge32 | RO | |
column · Gauge32 · read-only · current The number of seconds of aging time left for this client.
| ||||
| CcDot11ClientPacketsReceived | 1.3.6.1.4.1.9.9.273.1.3.1.1.6 | Counter32 | RO | |
column · Counter32 · read-only · current The number of packets received from this client.
| ||||
| CcDot11ClientBytesReceived | 1.3.6.1.4.1.9.9.273.1.3.1.1.7 | Counter32 | RO | |
column · Counter32 · read-only · current The number of bytes received from this client.
| ||||
| CcDot11ClientPacketsSent | 1.3.6.1.4.1.9.9.273.1.3.1.1.8 | Counter32 | RO | |
column · Counter32 · read-only · current The number of packets sent to this client.
| ||||
| CcDot11ClientBytesSent | 1.3.6.1.4.1.9.9.273.1.3.1.1.9 | Counter32 | RO | |
column · Counter32 · read-only · current The number of bytes sent to this client.
| ||||
| CcDot11ClientDuplicates | 1.3.6.1.4.1.9.9.273.1.3.1.1.10 | Counter32 | RO | |
column · Counter32 · read-only · current This counter increments when a packet for this client is received and the Sequence Control field in the packet header indicates the packet is a duplicate.
| ||||
| CcDot11ClientMsduRetries | 1.3.6.1.4.1.9.9.273.1.3.1.1.11 | Counter32 | RO | |
column · Counter32 · read-only · current This counter increments when an MSDU is successfully transmitted after one or more retransmissions for this client.
| ||||
| CcDot11ClientMsduFails | 1.3.6.1.4.1.9.9.273.1.3.1.1.12 | Counter32 | RO | |
column · Counter32 · read-only · current This counter increments when an MSDU is not transmitted successfully for this client due to the number of transmit attempts exceeding some limit.
| ||||
| CcDot11ClientWepErrors | 1.3.6.1.4.1.9.9.273.1.3.1.1.13 | Counter32 | RO | |
column · Counter32 · read-only · current This is the number of packets received from this client which failed to be properly decrypted via the WEP security mechanism.
| ||||
| CcDot11ClientMicErrors | 1.3.6.1.4.1.9.9.273.1.3.1.1.14 | Counter32 | RO | |
column · Counter32 · read-only · current This is the number of MIC errors for this client.
| ||||
| CcDot11ClientMicMissingFrames | 1.3.6.1.4.1.9.9.273.1.3.1.1.15 | Counter32 | RO | |
column · Counter32 · read-only · current This is the number of missing MIC packets for this client.
| ||||
| NciscoDot11StationTraps | 1.3.6.1.4.1.9.9.273.1.4 | |||
| !ciscoDot11StationStatusTrap | 1.3.6.1.4.1.9.9.273.1.4.1 | |||
notification · current ciscoDot11StationStatusTrap is generated when wireless client status change : 1. associate to AP 2. disassociate from AP 3. run state : client passes authentication and gets IP address | ||||
| TciscoDot11StationInfoTable | 1.3.6.1.4.1.9.9.273.1.5 | NA | ||
table · not-accessible · current Station Information parameters. | ||||
| RciscoDot11StationInfoEntry | 1.3.6.1.4.1.9.9.273.1.5.1 | NA | ||
| CclientMacAddr | 1.3.6.1.4.1.9.9.273.1.5.1.1 | MacAddress | AN | |
column · MacAddress · accessible-for-notify · current Indicates wireless client mac address. | ||||
| CclientDeviceType | 1.3.6.1.4.1.9.9.273.1.5.1.2 | CDot11ClientRoleClassType | AN | |
column · CDot11ClientRoleClassType · accessible-for-notify · current Indicates wireless client device type. possible types are client, ethernet, AP, Bridge, Repeater, WGB | ||||
| CclientDeviceName | 1.3.6.1.4.1.9.9.273.1.5.1.3 | SnmpAdminString | AN | |
column · SnmpAdminString · accessible-for-notify · current Indicates Cisco IOS device hostname . | ||||
| CclientIpv4Address | 1.3.6.1.4.1.9.9.273.1.5.1.4 | InetAddress | AN | |
column · InetAddress · accessible-for-notify · current Indicates wireless client IPv4 address. | ||||
| CclientIpv6Address | 1.3.6.1.4.1.9.9.273.1.5.1.5 | InetAddress | AN | |
column · InetAddress · accessible-for-notify · current Indicates wireless client IPv6 address. | ||||
| CapMacAddr | 1.3.6.1.4.1.9.9.273.1.5.1.6 | InetAddress | AN | |
column · InetAddress · accessible-for-notify · current Indicates AP mac address which client associated. | ||||
| CapIpv4Address | 1.3.6.1.4.1.9.9.273.1.5.1.7 | InetAddress | AN | |
column · InetAddress · accessible-for-notify · current Indicates AP IPv4 address that wireless client associates. | ||||
| CapIpv6Address | 1.3.6.1.4.1.9.9.273.1.5.1.8 | InetAddress | AN | |
column · InetAddress · accessible-for-notify · current Indicates AP IPv6 address that wireless client associates. | ||||
| CclientStationState | 1.3.6.1.4.1.9.9.273.1.5.1.9 | INTEGER | AN | |
column · INTEGER · accessible-for-notify · current This object indicates the state of the authentication and association process between the two parties: associated(1) - client associates to AP disAssociated(2) - client disassociates to AP run(3) - client passes authentication and gets IP address
| ||||
| CclientDisassocReasonStr | 1.3.6.1.4.1.9.9.273.1.5.1.10 | SnmpAdminString | AN | |
column · SnmpAdminString · accessible-for-notify · current This attribute holds the most recently transmitted Reason in a Disassociation frame. | ||||
| NciscoDot11AssocMIBConformance | 1.3.6.1.4.1.9.9.273.2 | |||
| NciscoDot11AssocMIBCompliances | 1.3.6.1.4.1.9.9.273.2.1 | |||
| MciscoDot11AssocMIBCompliance | 1.3.6.1.4.1.9.9.273.2.1.1 | deprecated | ||
compliance · deprecated The compliance statement for the ciscoDot11Assoc group. | ||||
| MciscoDot11AssocMIBComplianceRev1 | 1.3.6.1.4.1.9.9.273.2.1.2 | deprecated | ||
compliance · deprecated The compliance statement for the ciscoDot11Assoc group. This is deprecated in favor of the ciscoDot11AssocMIBComplianceRev2. | ||||
| MciscoDot11AssocMIBComplianceRev2 | 1.3.6.1.4.1.9.9.273.2.1.3 | deprecated | ||
compliance · deprecated The compliance statement for the ciscoDot11Assoc group. | ||||
| MciscoDot11AssocMIBComplianceRev3 | 1.3.6.1.4.1.9.9.273.2.1.4 | deprecated | ||
compliance · deprecated The compliance statement for this ciscoDot11AssociationMIB module. | ||||
| MciscoDot11AssocMIBComplianceRev4 | 1.3.6.1.4.1.9.9.273.2.1.5 | |||
compliance · current The compliance statement for this ciscoDot11AssociationMIB module. | ||||
| MciscoDot11AssocMIBComplianceRev5 | 1.3.6.1.4.1.9.9.273.2.1.6 | |||
compliance · current The compliance statement for this ciscoDot11AssociationMIB module. | ||||
| MciscoDot11AssocMIBComplianceRev6 | 1.3.6.1.4.1.9.9.273.2.1.7 | |||
compliance · current The compliance statement for this ciscoDot11AssociationMIB module.
| ||||
| NciscoDot11AssocMIBGroups | 1.3.6.1.4.1.9.9.273.2.2 | |||
| GciscoDot11AssocGlobalGroup | 1.3.6.1.4.1.9.9.273.2.2.1 | deprecated | ||
group · deprecated This is the device association information group. This is deprecated in favor of the ciscoDot11IfAssocStatGroup. | ||||
| GciscoDot11ClientConfigGroup | 1.3.6.1.4.1.9.9.273.2.2.2 | |||
group · current This is the client configuration information group. | ||||
| GciscoDot11ClientStatGroup | 1.3.6.1.4.1.9.9.273.2.2.3 | |||
group · current This is the client statistics group.
| ||||
| GciscoDot11ClientInfoGroup | 1.3.6.1.4.1.9.9.273.2.2.4 | |||
group · current This group provides additional client specific information. | ||||
| GciscoDot11ApAssocGlobalGroup | 1.3.6.1.4.1.9.9.273.2.2.5 | |||
group · current This group includes per AP or bridge global configuration information.
| ||||
| GciscoDot11IfAssocStatGroup | 1.3.6.1.4.1.9.9.273.2.2.6 | |||
group · current This group includes per IEEE 802.11 radio interface association statistics. | ||||
| GciscoDot11IfCipherStatGroup | 1.3.6.1.4.1.9.9.273.2.2.7 | |||
group · current This group includes per IEEE 802.11 radio interface cipher related statistics collected. | ||||
| GciscoDot11ClientAuthenGroup | 1.3.6.1.4.1.9.9.273.2.2.8 | deprecated | ||
group · deprecated This group includes per IEEE 802.11 radio interface cipher related statistics collected. | ||||
| GciscoDot11ClientConfigExtGroup | 1.3.6.1.4.1.9.9.273.2.2.9 | |||
group · current This group provides more configuration information about a particular associated 802.11 client.
| ||||
| GciscoDot11ClientNewAuthenGroup | 1.3.6.1.4.1.9.9.273.2.2.10 | |||
group · current This group includes per IEEE 802.11 radio interface cipher related statistics collected.
| ||||
| GciscoDot11ClientStatusTrapsGroup | 1.3.6.1.4.1.9.9.273.2.2.11 | |||
group · current This group includes wireless client information that association or disassociation trap includes. | ||||
Textual conventions
CDot11AdditionalAuthenMethodBitseap(1)mac(0)These are the additional authentications that can be performed after IEEE 802.11 Open System or Shared Key authentication is completed successfully: mac(0) - MAC address authentication eap(1) - EAP authentication.CDot11AuthenticationMethodINTEGERnetworkEap(129)open(1)sharedKey(2)These are the IEEE 802.11 supported authentication methods for wireless devices: open(1) - Open System sharedKey(2) - Shared Key networkEap(129) - Network EAP.CDot11ClientDevTypeINTEGERc1100SeriesAP(129)c1130SeriesAP(137)c1200SeriesAP(132)c1240SeriesAP(140)c1310SeriesBridge(138)c1410SeriesBridge(130)c350SeriesAP(134)c7920phone(139)cb21agClient(135)ethernetAP(76)ethernetBridge(77)ethernetClient(112)ethernetUC(86)generic80211Client(104)mc(111)mp2xClient(133)pc3000Client(84)pc3100Client(110)pc3500Client(101)pc4500Client(102)pc4800Client(109)pc4800bClient(117)radioKodiak(136)serialUC(85)series350Client(127)series370Client(128)unknown(1)wgb(124)wgbNoDiversity(123)This defines the classifications of wireless client device. The devices are classified by their Ethernet connection, serial connection, and the type of radio it uses. The device classifications are: unknown(1) - unknown, ethernetAP(76) - Ethernet access point, ethernetBridge(77) - Ethernet bridge, pc3000Client(84) - client with a 3000 radio, serialUC(85) - serial port universal client, ethernetUC(86) - Ethernet universal client, pc3500Client(101) - client with a 5300 radio, pc4500Client(102) - client with a 4500 radio, generic80211Client(104) - client of an unknown radio type and non-Cisco device, pc4800Client(109) - client with a 4800 radio, pc3100Client(110) - client with a 3100 radio, mc(111) - multiple client Ethernet, universal client, ethernetClient(112) - Ethernet client of a WGB, pc4800bClient(117) - client with a 4800b radio, wgbNoDiversity(123) - WGB with one antenna, wgb(124) - WGB with two antennas, series350Client(127) - client with 350 series radio, series370Client(128) - client with 370 series dot11A radio, c1100SeriesAP(129) - Cisco 1100 series AP, c1410SeriesBridge(130) - Cisco 1410 series bridge, c1200SeriesAP(132) - Cisco 1200 series AP, mp2xClient(133) - client with MP2x IEEE 802.11g radio, c350SeriesAP(134) - Cisco IOS 350 series AP, cb21agClient(135) - Cisco CB21AG/PI21AG IEEE 802.lla/b/g client, radioKodiak(136) - Cisco IEEE 802.11a AIR-RM21A-x-K9 and AIR-RM22A-x-K9 radio, c1130SeriesAP(137) - Cisco 1130 series AP, c1310SeriesBridge(138) - Cisco 1310 series bridge, c7920phone(139) - Cisco 7920 series phone, c1240SeriesAP(140) - Cisco 1240 series AP.CDot11ClientRadioTypeINTEGERbridge1410(36)cb21ag(46)ccxClient(2)mp2xMAR(40)mp2xSeries(37)pc3000(4)pc3100(13)pc3500(3)pc4500(6)pc4800(12)rm2gSeries(39)rm2xSeries(38)series340(33)series350(34)series370(35)unknown(1)This defines the radio classifications of wireless stations. It indicates the model number of the radio in the remote unit. The radio classifications are: unknown(1) - unknown, ccxClient(2) - CCX-compatible radio, pc3500(3) - Cisco 3500 radio, pc3000(4) - Cisco 3000 radio, pc4500(6) - Cisco 4500 radio, pc4800(12) - Cisco 4800 radio, pc3100(13) - Cisco 3100 radio, series340(33) - Cisco 340 series radio, series350(34) - Cisco 350 series radio, series370(35) - Cisco 370 series dot11A radio, bridge1410(36) - Cisco 1410 bridge 5GHz radio, mp2xSeries(37) - Cisco 11g MP2x series radio, rm2xSeries(38) - Cisco 11a RM2x series radio, rm2gSeries(39) - Cisco 11g RM2x series radio, mp2xMAR(40) - Cisco 3210 MAR 11g MP2x radio, cb21ag(46) - Cisco CB21AG/PI21AG IEEE 802.11a/b/g radio.CDot11ClientRoleClassTypeINTEGERaccessPoint(2)bridge(4)bridgeHost(3)bridgeRoot(5)clientStation(0)ethernetClient(6)repeater(1)This defines the type of role of a wireless device. The device types are: clientStation(0) - client station, repeater(1) - repeater access point, accessPoint(2) - access point, bridgeHost(3) - bridge host (WGB), bridge(4) - bridge, bridgeRoot(5) - root bridge ethernetClient(6) - Ethernet client through WGB.CDot11Dot1xAuthenMethodBitseapFast(5)eapSim(4)eapTls(3)leap(1)md5(0)peap(2)These are the IEEE 802.1x authentication methods performed between the IEEE 802.11 wireless clients and the authentication server. Depending on the server and client configuration, more than one authentication methods can be performed for any IEEE 802.11 association. The IEEE 802.1x authentication methods are: md5(0) - Message-digest algorithm leap(1) - Cisco Light-weight EAP peap(2) - Protected EAP eapTls(3) - EAP Transport Layer Security eapSim(4) - EAP Enhanced GSM Authentication eapFast(5) - Cisco EAP Fast.CDot11KeyManagementMethodBitscckm(1)wpa(0)These are the encryption key management methods for IEEE 802.11 wireless frame encryption. The key management methods are: wpa(0) - Wi-Fi Protected Access cckm(1) - Cisco proprietary key management.CDot11NewKeyManagementMethodBitscckm(0)wpa1(1)wpa2(2)These are the encryption key management methods for IEEE 802.11 wireless frame encryption. The key management methods are: cckm(0) - Cisco proprietary key management wpa1(1) - Wi-Fi Protected Access version 1 wpa2(2) - Wi-Fi Protected Access version 2.
Traps / Notifications
- ciscoDot11StationStatusTrap
1.3.6.1.4.1.9.9.273.1.4.1
Groups and compliance
- ciscoDot11ApAssocGlobalGroup
- ciscoDot11AssocGlobalGroup
- ciscoDot11AssocMIBCompliance
- ciscoDot11AssocMIBComplianceRev1
- ciscoDot11AssocMIBComplianceRev2
- ciscoDot11AssocMIBComplianceRev3
- ciscoDot11AssocMIBComplianceRev4
- ciscoDot11AssocMIBComplianceRev5
- ciscoDot11AssocMIBComplianceRev6
- ciscoDot11ClientAuthenGroup
- ciscoDot11ClientConfigExtGroup
- ciscoDot11ClientConfigGroup
- ciscoDot11ClientInfoGroup
- ciscoDot11ClientNewAuthenGroup
- ciscoDot11ClientStatGroup
- ciscoDot11ClientStatusTrapsGroup
- ciscoDot11IfAssocStatGroup
- ciscoDot11IfCipherStatGroup