CIENA-CES-OAM-MIB
Ciena CorporationThis module defines the EFM OAM statistics objects and also the objects required for EFM OAM related notifications.
snmptranslate -m CIENA-CES-OAM-MIB -Tpsnmpwalk -v2c -c <community> -m CIENA-CES-OAM-MIB <host> 1.3.6.1.4.1.1271.2.3.5Imports
| CIENA-GLOBAL-MIB | cienaGlobalMacAddress, cienaGlobalSeverity |
|---|---|
| CIENA-SMI | cienaCesNotifications, cienaCesStatistics |
| CIENA-TC | CienaStatsClear |
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP |
| SNMPv2-SMI | Bits, Counter32, Counter64, Integer32, IpAddress, MODULE-IDENTITY, MibIdentifier, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, iso |
| SNMPv2-TC | DisplayString, PhysAddress, TEXTUAL-CONVENTION, TimeStamp |
OID tree
| Name | OID | Type | Access | Status |
|---|---|---|---|---|
| NcienaCesOamNotifMIBNotificationPrefix | 1.3.6.1.4.1.1271.2.2.15 | |||
| NcienaCesOamNotifMIBNotification | 1.3.6.1.4.1.1271.2.2.15.0 | |||
| !cienaCesOamLinkEventTrap | 1.3.6.1.4.1.1271.2.2.15.0.1 | |||
notification · current A cienaCesOamLinkEventTrap notification is sent whenever a local or remote link event is detected and recorded in the cienaCesOamEventLogTable. To enable the device to send this trap, cienaCesOamLinkEventTrapState needs to be set to enabled. The cienaCesOamLinkEventTrapState is enabled by default. Variable bindings include: cienaGlobalSeverity, cienaGlobalMacAddress, cienaCesOamEventNotifChassisIndex, cienaCesOamEventNotifShelfIndex, cienaCesOamEventNotifSlotIndex, cienaCesOamEventNotifPortNumber, cienaCesOamEventLogType, cienaCesOamEventLogLocation, and cienaCesOamEventNotifChannelNumber. | ||||
| IcienaCesOamMibModule | 1.3.6.1.4.1.1271.2.3.5 | |||
identity This module defines the EFM OAM statistics objects and also the objects required for EFM OAM related notifications. | ||||
| NcienaCesOamMIB | 1.3.6.1.4.1.1271.2.3.5.1 | |||
| NcienaCesOamStatistics | 1.3.6.1.4.1.1271.2.3.5.1.1 | |||
| TcienaCesOamStatsTable | 1.3.6.1.4.1.1271.2.3.5.1.1.1 | NA | ||
table · not-accessible · current Statistics for the OAM function on a particular Ethernet-like interface. | ||||
| RcienaCesOamStatsEntry | 1.3.6.1.4.1.1271.2.3.5.1.1.1.1 | NA | ||
row · not-accessible · current An entry in the table, containing statistical information on the Ethernet OAM function for a single Ethernet-like interface.
| ||||
| CcienaCesOamInformationTx | 1.3.6.1.4.1.1271.2.3.5.1.1.1.1.1 | Counter32 | RO | |
column · Counter32 · read-only · current A count of the number of Information OAMPDUs transmitted on this interface. An Information OAMPDU is indicated by a valid frame with (1) destination MAC address equal to that of the reserved MAC address for Slow Protocols (See 43B of [802.3ah]), (2) a lengthOrType field equal to the reserved type for Slow Protocols, (3) a Slow Protocols subtype equal to that of the subtype reserved for OAM, and (4) an OAMPDU code equal to the OAM Information code. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.
| ||||
| CcienaCesOamInformationRx | 1.3.6.1.4.1.1271.2.3.5.1.1.1.1.2 | Counter32 | RO | |
column · Counter32 · read-only · current A count of the number of Information OAMPDUs received on this interface. An Information OAMPDU is indicated by a valid frame with (1) destination MAC address equal to that of the reserved MAC address for Slow Protocols (See 43B of [802.3ah]), (2) a lengthOrType field equal to the reserved type for Slow Protocols, (3) a Slow Protocols subtype equal to that of the subtype reserved for OAM, and (4) an OAMPDU code equal to the OAM Information code. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.
| ||||
| CcienaCesOamUniqueEventNotificationTx | 1.3.6.1.4.1.1271.2.3.5.1.1.1.1.3 | Counter32 | RO | |
column · Counter32 · read-only · current A count of the number of unique Event OAMPDUs transmitted on this interface. Event notifications may be sent in duplicate to increase the probability of successfully being received, given the possibility that a frame may be lost in transit. An Event Notification OAMPDU is indicated by a valid frame with (1) destination MAC address equal to that of the reserved MAC address for Slow Protocols (See 43B of [802.3ah]), (2) a lengthOrType field equal to the reserved type for Slow Protocols, (3) a Slow Protocols subtype equal to that of the subtype reserved for OAM, and (4) an OAMPDU code equal to the OAM Event code. A unique Event Notification OAMPDU is indicated as an Event Notification OAMPDU with a Sequence Number field that is distinct from the previously transmitted Event Notification OAMPDU Sequence Number. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.
| ||||
| CcienaCesOamUniqueEventNotificationRx | 1.3.6.1.4.1.1271.2.3.5.1.1.1.1.4 | Counter32 | RO | |
column · Counter32 · read-only · current A count of the number of unique Event OAMPDUs received on this interface. Event notification OAMPDUs may be sent in duplicate to increase the probability of successfully being received, given the possibility that a frame may be lost in transit. An Event Notification OAMPDU is indicated by a valid frame with (1) destination MAC address equal to that of the reserved MAC address for Slow Protocols (See 43B of [802.3ah]), (2) a lengthOrType field equal to the reserved type for Slow Protocols, (3) a Slow Protocols subtype equal to that of the subtype reserved for OAM, and (4) an OAMPDU code equals the OAM Event code. A unique Event Notification OAMPDU is indicated as an Event Notification OAMPDU with a Sequence Number field that is distinct from the previously received Event Notification OAMPDU Sequence Number. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.
| ||||
| CcienaCesOamLoopbackControlTx | 1.3.6.1.4.1.1271.2.3.5.1.1.1.1.5 | Counter32 | RO | |
column · Counter32 · read-only · current A count of the number of Loopback Control OAMPDUs transmitted on this interface. An Loopback Control OAMPDU is indicated by a valid frame with (1) destination MAC address equal to that of the reserved MAC address for Slow Protocols (See 43B of [802.3ah]), (2) a lengthOrType field equal to the reserved type for Slow Protocols, (3) a Slow Protocols subtype equal to that of the subtype reserved for OAM, and (4) an OAMPDU code equal to the OAM Loopback Control code. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.
| ||||
| CcienaCesOamLoopbackControlRx | 1.3.6.1.4.1.1271.2.3.5.1.1.1.1.6 | Counter32 | RO | |
column · Counter32 · read-only · current A count of the number of Loopback Control OAMPDUs transmitted on this interface. An Loopback Control OAMPDU is indicated by a valid frame with (1) destination MAC address equal to that of the reserved MAC address for Slow Protocols (See 43B of [802.3ah]), (2) a lengthOrType field equal to the reserved type for Slow Protocols, (3) a Slow Protocols subtype equal to that of the subtype reserved for OAM, and (4) an OAMPDU code equal to the OAM Loopback Control code. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.
| ||||
| CcienaCesOamVariableRequestTx | 1.3.6.1.4.1.1271.2.3.5.1.1.1.1.7 | Counter32 | RO | |
column · Counter32 · read-only · current A count of the number of Variable Request OAMPDUs transmitted on this interface. An Variable Request OAMPDU is indicated by a valid frame with (1) destination MAC address equal to that of the reserved MAC address for Slow Protocols (See 43B of [802.3ah]), (2) a lengthOrType field equal to the reserved type for Slow Protocols, (3) a Slow Protocols subtype equal to that of the subtype reserved for OAM, and (4) an OAMPDU code equal to the OAM Variable Request code. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.
| ||||
| CcienaCesOamVariableRequestRx | 1.3.6.1.4.1.1271.2.3.5.1.1.1.1.8 | Counter32 | RO | |
column · Counter32 · read-only · current A count of the number of Variable Request OAMPDUs received on this interface. An Variable Request OAMPDU is indicated by a valid frame with (1) destination MAC address equal to that of the reserved MAC address for Slow Protocols (See 43B of [802.3ah]), (2) a lengthOrType field equal to the reserved type for Slow Protocols, (3) a Slow Protocols subtype equal to that of the subtype reserved for OAM, and (4) an OAMPDU code equal to the OAM Variable Request code. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.
| ||||
| CcienaCesOamVariableResponseTx | 1.3.6.1.4.1.1271.2.3.5.1.1.1.1.9 | Counter32 | RO | |
column · Counter32 · read-only · current A count of the number of Variable Response OAMPDUs transmitted on this interface. An Variable Response OAMPDU is indicated by a valid frame with (1) destination MAC address equal to that of the reserved MAC address for Slow Protocols (See 43B of [802.3ah]), (2) a lengthOrType field equal to the reserved type for Slow Protocols, (3) a Slow Protocols subtype equal to that of the subtype reserved for OAM, and (4) an OAMPDU code equal to the OAM Variable Response code. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.
| ||||
| CcienaCesOamVariableResponseRx | 1.3.6.1.4.1.1271.2.3.5.1.1.1.1.10 | Counter32 | RO | |
column · Counter32 · read-only · current A count of the number of Variable Response OAMPDUs received on this interface. An Variable Response OAMPDU is indicated by a valid frame with (1) destination MAC address equal to that of the reserved MAC address for Slow Protocols (See 43B of [802.3ah]), (2) a lengthOrType field equal to the reserved type for Slow Protocols, (3) a Slow Protocols subtype equal to that of the subtype reserved for OAM, and (4) an OAMPDU code equal to the OAM Variable Response code. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.
| ||||
| CcienaCesOamOrgSpecificTx | 1.3.6.1.4.1.1271.2.3.5.1.1.1.1.11 | Counter32 | RO | |
column · Counter32 · read-only · current A count of the number of Organization Specific OAMPDUs transmitted on this interface. An Organization Specific OAMPDU is indicated by a valid frame with (1) destination MAC address equal to that of the reserved MAC address for Slow Protocols (See 43B of [802.3ah]), (2) a lengthOrType field equal to the reserved type for Slow Protocols, (3) a Slow Protocols subtype equal to that of the subtype reserved for OAM, and (4) an OAMPDU code equal to the OAM Organization Specific code. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.
| ||||
| CcienaCesOamOrgSpecificRx | 1.3.6.1.4.1.1271.2.3.5.1.1.1.1.12 | Counter32 | RO | |
column · Counter32 · read-only · current A count of the number of Organization Specific OAMPDUs received on this interface. An Organization Specific OAMPDU is indicated by a valid frame with (1) destination MAC address equal to that of the reserved MAC address for Slow Protocols (See 43B of [802.3ah]), (2) a lengthOrType field equal to the reserved type for Slow Protocols, (3) a Slow Protocols subtype equal to that of the subtype reserved for OAM, and (4) an OAMPDU code equal to the OAM Organization Specific code. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.
| ||||
| CcienaCesOamUnsupportedCodesTx | 1.3.6.1.4.1.1271.2.3.5.1.1.1.1.13 | Counter32 | RO | |
column · Counter32 · read-only · current A count of the number of OAMPDUs transmitted on this interface with an unsupported op-code. An unsupported op-code OAMPDU is indicated by a valid frame with (1) destination MAC address equal to that of the reserved MAC address for Slow Protocols (See 43B of [802.3ah]), (2) a lengthOrType field equal to the reserved type for Slow Protocols, (3) a Slow Protocols subtype equal to that of the subtype reserved for OAM, and (4) an OAMPDU code equal to the op-code for a function that is not supported by the device. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.
| ||||
| CcienaCesOamUnsupportedCodesRx | 1.3.6.1.4.1.1271.2.3.5.1.1.1.1.14 | Counter32 | RO | |
column · Counter32 · read-only · current A count of the number of OAMPDUs received on this interface with an unsupported op-code. An unsupported op-code OAMPDU is indicated by a valid frame with (1) destination MAC address equal to that of the reserved MAC address for Slow Protocols (See 43B of [802.3ah]), (2) a lengthOrType field equal to the reserved type for Slow Protocols, (3) a Slow Protocols subtype equal to that of the subtype reserved for OAM, and (4) an OAMPDU code equal to the opcode for a function that is not supported by the device. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.
| ||||
| CcienaCesOamframesLostDueToOam | 1.3.6.1.4.1.1271.2.3.5.1.1.1.1.15 | Counter32 | RO | |
column · Counter32 · read-only · current A count of the number of frames that were dropped by the OAM multiplexer. Since the OAM multiplexer has multiple inputs and a single output, there may be cases where frames are dropped due to transmit resource contention. This counter is incremented whenever a frame is dropped by the OAM layer. When this counter is incremented, no other counters in this MIB are incremented. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.
| ||||
| CcienaCesOamStatsPort | 1.3.6.1.4.1.1271.2.3.5.1.1.1.1.16 | Integer32 (1..1000) | NA | |
column · Integer32 (1..1000) · not-accessible · current An Ethernet port on the switch. | ||||
| CcienaCesOamDuplicateEventNotificationTx | 1.3.6.1.4.1.1271.2.3.5.1.1.1.1.17 | Counter32 | RO | |
column · Counter32 · read-only · current A count of the number of duplicate Event OAMPDUs transmitted on this interface. Event notification OAMPDUs may be sent in duplicate to increase the probability of successfully being received, given the possibility that a frame may be lost in transit. An Event Notification OAMPDU is indicated by a valid frame with (1) destination MAC address equal to that of the reserved MAC address for Slow Protocols (See 43B of [802.3ah]), (2) a lengthOrType field equal to the reserved type for Slow Protocols, (3) a Slow Protocols subtype equal to that of the subtype reserved for OAM, and (4) an OAMPDU code equals to the OAM Event code. A duplicate Event Notification OAMPDU is indicated as an Event Notification OAMPDU with a Sequence Number field that is identical to the previously transmitted Event Notification OAMPDU Sequence Number. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.
| ||||
| CcienaCesOamDuplicateEventNotificationRx | 1.3.6.1.4.1.1271.2.3.5.1.1.1.1.18 | Counter32 | RO | |
column · Counter32 · read-only · current A count of the number of duplicate Event OAMPDUs received on this interface. Event notification OAMPDUs may be sent in duplicate to increase the probability of successfully being received, given the possibility that a frame may be lost in transit. An Event Notification OAMPDU is indicated by a valid frame with (1) destination MAC address equal to that of the reserved MAC address for Slow Protocols (See 43B of [802.3ah]), (2) a lengthOrType field equal to the reserved type for Slow Protocols, (3) a Slow Protocols subtype equal to that of the subtype reserved for OAM, and (4) an OAMPDU code equal to the OAM Event code. A duplicate Event Notification OAMPDU is indicated as an Event Notification OAMPDU with a Sequence Number field that is identical to the previously received Event Notification OAMPDU Sequence Number. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of the ifCounterDiscontinuityTime.
| ||||
| TcienaCesOamEventLogTable | 1.3.6.1.4.1.1271.2.3.5.1.1.2 | NA | ||
table · not-accessible · current This table records a history of the events that have occurred at the Ethernet OAM level. These events can include locally detected events, which may result in locally generated OAMPDUs, and remotely detected events, which are detected by the OAM peer entity and signaled to the local entity via Ethernet OAM. Ethernet OAM events can be signaled by Event Notification OAMPDUs or by the flags field in any OAMPDU. | ||||
| RcienaCesOamEventLogEntry | 1.3.6.1.4.1.1271.2.3.5.1.1.2.1 | NA | ||
row · not-accessible · current An entry in the cienaCesOamEventLogTable. | ||||
| CcienaCesOamEventLogPort | 1.3.6.1.4.1.1271.2.3.5.1.1.2.1.1 | Integer32 | NA | |
column · Integer32 · not-accessible · current An Ethernet port on the switch. | ||||
| CcienaCesOamEventLogIndex | 1.3.6.1.4.1.1271.2.3.5.1.1.2.1.2 | Unsigned32 | NA | |
column · Unsigned32 · not-accessible · current An arbitrary integer for identifying individual events within the event log. | ||||
| CcienaCesOamEventLogTimestamp | 1.3.6.1.4.1.1271.2.3.5.1.1.2.1.3 | TimeStamp | RO | |
column · TimeStamp · read-only · current The value of sysUpTime at the time of the logged event. For locally generated events, the time of the event can be accurately retrieved from sysUpTime. For remotely generated events, the time of the event is indicated by the reception of the Event Notification OAMPDU indicating the event occurred on the peer. A system may attempt to adjust the timestamp value to more accurately reflect the time of the event at the peer OAM entity by using other information, such as that found in the timestamp found on the Event Notification TLVs, which provides an indication of the relative time between events at the peer entity. | ||||
| CcienaCesOamEventLogOui | 1.3.6.1.4.1.1271.2.3.5.1.1.2.1.4 | OCTET STRING (SIZE (3)) | RO | |
column · OCTET STRING (SIZE (3)) · read-only · current The OUI of the entity defining the object type. All IEEE 802.3 defined events (as appearing in [802.3ah] except for the Organizationally Unique Event TLVs) use the IEEE 802.3 OUI of 0x0180C2. Organizations defining their own Event Notification TLVs include their OUI in the Event Notification TLV, which gets reflected here. | ||||
| CcienaCesOamEventLogType | 1.3.6.1.4.1.1271.2.3.5.1.1.2.1.5 | INTEGER | RO | |
column · INTEGER · read-only · current The type of event that generated this entry in the event log.
When the OUI is the IEEE 802.3 OUI of 0x0180C2, the following
event types are defined:
erroredSymbolEvent(1),
erroredFramePeriodEvent (2),
erroredFrameEvent(3),
erroredFrameSecondsEvent(4),
linkFault(256),
dyingGaspEvent(257),
criticalLinkEvent(258)
The first four are considered threshold crossing events as
they are generated when a metric exceeds a given value within
a specified window. The other three are not threshold
crossing events.
When the OUI is not 0x0180C2, then some other organization has
defined the event space. If event subtyping is known to the
implementation, it may be reflected here. Otherwise, this
value should return noEvent (99).
| ||||
| CcienaCesOamEventLogLocation | 1.3.6.1.4.1.1271.2.3.5.1.1.2.1.6 | INTEGER | RO | |
column · INTEGER · read-only · current Whether this event occurred locally, or was received from the OAM peer via Ethernet OAM.
| ||||
| CcienaCesOamEventLogWindowHi | 1.3.6.1.4.1.1271.2.3.5.1.1.2.1.7 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current If the event represents a threshold crossing event, the two objects cienaCesOamEventWindowHi and cienaCesOamEventWindowLo form an unsigned 64-bit integer yielding the window over which the value was measured for the threshold crossing event (e.g., 5, when 11 occurrences happened in 5 seconds while the threshold was 10). The two objects are combined as: cienaCesOamEventLogWindow = ((2^32) * cienaCesOamEventLogWindowHi) + cienaCesOamEventLogWindowLo. Otherwise, this value is returned as all Fs (0xFFFFFFFF) and adds no useful information. | ||||
| CcienaCesOamEventLogWindowLo | 1.3.6.1.4.1.1271.2.3.5.1.1.2.1.8 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current If the event represents a threshold crossing event, the two objects cienaCesOamEventWindowHi and cienaCesOamEventWindowLo form an unsigned 64-bit integer yielding the window over which the value was measured for the threshold crossing event (e.g., 5, when 11 occurrences happened in 5 seconds while the threshold was 10). The two objects are combined as: cienaCesOamEventLogWindow = ((2^32) * cienaCesOamEventLogWindowHi) + cienaCesOamEventLogWindowLo. Otherwise, this value is returned as all Fs (0xFFFFFFFF) and adds no useful information. | ||||
| CcienaCesOamEventLogThresholdHi | 1.3.6.1.4.1.1271.2.3.5.1.1.2.1.9 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current If the event represents a threshold crossing event, the two objects cienaCesOamEventThresholdHi and cienaCesOamEventThresholdLo form an unsigned 64-bit integer yielding the value that was crossed for the threshold crossing event (e.g., 10, when 11 occurrences happened in 5 seconds while the threshold was 10). The two objects are combined as: cienaCesOamEventLogThreshold = ((2^32) * cienaCesOamEventLogThresholdHi) + cienaCesOamEventLogThresholdLo. Otherwise, this value is returned as all Fs (0xFFFFFFFF) and adds no useful information. | ||||
| CcienaCesOamEventLogThresholdLo | 1.3.6.1.4.1.1271.2.3.5.1.1.2.1.10 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current If the event represents a threshold crossing event, the two objects cienaCesOamEventThresholdHi and cienaCesOamEventThresholdLo form an unsigned 64-bit integer yielding the value that was crossed for the threshold crossing event (e.g., 10, when 11 occurrences happened in 5 seconds while the threshold was 10). The two objects are combined as: cienaCesOamEventLogThreshold = ((2^32) * cienaCesOamEventLogThresholdHi) + cienaCesOamEventLogThresholdLo. Otherwise, this value is returned as all Fs (0xFFFFFFFF) and adds no useful information. | ||||
| CcienaCesOamEventLogValue | 1.3.6.1.4.1.1271.2.3.5.1.1.2.1.11 | Counter64 | RO | |
column · Counter64 · read-only · current If the event represents a threshold crossing event, this value indicates the value of the parameter within the given window that generated this event (e.g., 11, when 11 occurrences happened in 5 seconds while the threshold was 10). Otherwise, this value is returned as all F's (0xFFFFFFFFFFFFFFFF) and adds no useful information. | ||||
| CcienaCesOamEventLogRunningTotal | 1.3.6.1.4.1.1271.2.3.5.1.1.2.1.12 | Counter64 | RO | |
column · Counter64 · read-only · current This value represents the total number of times this occurrence has happened since the last reset (e.g., 3253, when 3253 symbol errors have occurred since the last reset, which has resulted in 51 symbol error threshold crossing events since the last reset). | ||||
| CcienaCesOamEventLogEventTotal | 1.3.6.1.4.1.1271.2.3.5.1.1.2.1.13 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current This value represents the total number of times one or more of these occurrences have resulted in an event (e.g., 51 when 3253 symbol errors have occurred since the last reset, which has resulted in 51 symbol error threshold crossing events since the last reset). | ||||
| CcienaCesOamEventNotifChassisIndex | 1.3.6.1.4.1.1271.2.3.5.1.1.2.1.14 | Unsigned32 (1) | AN | |
column · Unsigned32 (1) · accessible-for-notify · current This object indicates the chassis index for the port used for trap definition. | ||||
| CcienaCesOamEventNotifShelfIndex | 1.3.6.1.4.1.1271.2.3.5.1.1.2.1.15 | Unsigned32 (1) | AN | |
column · Unsigned32 (1) · accessible-for-notify · current This object indicates the shelf index for the port used for trap definition. | ||||
| CcienaCesOamEventNotifSlotIndex | 1.3.6.1.4.1.1271.2.3.5.1.1.2.1.16 | Unsigned32 (1..7) | AN | |
column · Unsigned32 (1..7) · accessible-for-notify · current This object indicates the slot index for the port used for trap definition. | ||||
| CcienaCesOamEventNotifPortNumber | 1.3.6.1.4.1.1271.2.3.5.1.1.2.1.17 | Unsigned32 (1..65535) | AN | |
column · Unsigned32 (1..65535) · accessible-for-notify · current This object indicates the port number for the corresponding PGID used for trap definition. | ||||
| CcienaCesOamEventNotifChannelNumber | 1.3.6.1.4.1.1271.2.3.5.1.1.2.1.18 | Unsigned32 | AN | |
column · Unsigned32 · accessible-for-notify · current This object indicates the channel number for the corresponding PGID used for trap definition. The value 0 is used if port of concern is not channelized. | ||||
| ScienaCesOamStatsClear | 1.3.6.1.4.1.1271.2.3.5.1.1.3 | CienaStatsClear | RW | |
scalar · CienaStatsClear · read-write · current Setting this object to 'true' causes the values of all objects maintained within the cienaCesOamStatsTable to reset to the value of zero. When read, this object always returns the value of false. | ||||
| TcienaCesOamTable | 1.3.6.1.4.1.1271.2.3.5.1.1.4 | NA | ||
table · not-accessible · current Primary controls and status for the OAM capabilities of an Ethernet like interface. There is one row in this table for each Ethernet like interface in the system that supports the Ethernet OAM functions defined in [802.3ah]. | ||||
| RcienaCesOamEntry | 1.3.6.1.4.1.1271.2.3.5.1.1.4.1 | NA | ||
row · not-accessible · current An entry in the table. Contains an Ethernet like interface in the system that supports the Ethernet OAM functions defined in [802.3ah].
| ||||
| CcienaCesOamPort | 1.3.6.1.4.1.1271.2.3.5.1.1.4.1.1 | Integer32 | NA | |
column · Integer32 · not-accessible · current An Ethernet port on the switch. | ||||
| CcienaCesOamAdminState | 1.3.6.1.4.1.1271.2.3.5.1.1.4.1.2 | INTEGER | RO | |
column · INTEGER · read-only · current This object is used to provision the default administrative OAM mode for this
interface. This object represents the desired state of OAM for this interface.
The cienaCesOamAdminState always starts in the disabled(1) state
until an explicit management action or configuration
information retained by the system causes a transition to the
enabled(2) state.
Note that the value of this object is ignored when the
interface is not operating in full-duplex mode. OAM is not
supported on half-duplex links.
| ||||
| CcienaCesOamOperStatus | 1.3.6.1.4.1.1271.2.3.5.1.1.4.1.3 | INTEGER | RO | |
column · INTEGER · read-only · current At initialization and failure conditions, two OAM entities on the same full-duplex Ethernet link begin a discovery phase to determine what OAM capabilities may be used on that link. The progress of this initialization is controlled by the OAM sub layer. This value is always disabled(1) if OAM is disabled on this interface via the cienaCesOamAdminState. If the link has detected a fault and is transmitting OAMPDUs with a link fault indication, the value is linkFault(2). The passiveWait(3) state is returned only by OAM entities in passive mode (cienaCesOamMode) and reflects the state in which the OAM entity is waiting to see if the peer device is OAM capable. The activeSendLocal(4) is used by active mode devices (cienaCesOamMode) and reflects the OAM entity actively trying to discover whether the peer has OAM capability but has not yet made that determination. The state sendLocalAndRemote(5) indicates that the local OAM entity has discovered the peer but has not yet accepted or rejected the configuration of the peer. The local device can, for whatever reason, decide that the peer device is unacceptable and decline OAM peering. If the local OAM entity rejects the peer OAM entity, the state becomes oamPeeringLocallyRejected(7). If the OAM peering is allowed by the local device, the state moves to sendLocalAndRemoteOk(6). Note that both the sendLocalAndRemote(5) and oamPeeringLocallyRejected(7) states fall within the state SEND_LOCAL_REMOTE of the Discovery state diagram [802.3ah, Figure 57-5], with the difference being whether the local OAM client has actively rejected the peering or has just not indicated any decision yet. Whether a peering decision has been made is indicated via the local flags field in the OAMPDU (reflected in the aOAMLocalFlagsField of 30.3.6.1.10). If the remote OAM entity rejects the peering, the state becomes oamPeeringRemotelyRejected(8). Note that both the sendLocalAndRemoteOk(6) and oamPeeringRemotelyRejected(8) states fall within the state SEND_LOCAL_REMOTE_OK of the Discovery state diagram [802.3ah, Figure 57-5], with the difference being whether the remote OAM client has rejected the peering or has just not yet decided. This is indicated via the remote flags field in the OAM PDU (reflected in the aOAMRemoteFlagsField of 30.3.6.1.11). When the local OAM entity learns that both it and the remote OAM entity have accepted the peering, the state moves to operational(9) corresponding to the SEND_ANY state of the Discovery state diagram [802.3ah, Figure 57-5].
| ||||
| CcienaCesOamMode | 1.3.6.1.4.1.1271.2.3.5.1.1.4.1.4 | INTEGER | RO | |
column · INTEGER · read-only · current This object indicates the mode of OAM operation for this
Ethernet like interface. OAM on Ethernet interfaces may be in
'active' mode or 'passive' mode. These two modes differ in
that active mode provides additional capabilities to initiate
monitoring activities with the remote OAM peer entity, while
passive mode generally waits for the peer to initiate OAM
actions with it. As an example, an active OAM entity can put
the remote OAM entity in a loopback state, where a passive OAM
entity cannot.
The default value of cienaCesOamMode is dependent on the type of
system on which this Ethernet like interface resides. The
default value should be 'active(1)' unless it is known that
this system should take on a subservient role to the other
device connected over this interface.
If this values gets changed it value results in incrementing the
configuration revision field of locally generated OAMPDUs (30.3.6.1.12)
and potentially re-doing the OAM discovery process if the
cienaCesOamOperStatus was already operational(9).
| ||||
| CcienaCesMaxOamPduSize | 1.3.6.1.4.1.1271.2.3.5.1.1.4.1.5 | Integer32 | RO | |
column · Integer32 · read-only · current The largest OAMPDU that the OAM entity supports. OAM entities exchange maximum OAMPDU sizes and negotiate to use the smaller of the two maximum OAMPDU sizes between the peers. This value is determined by the local implementation.
| ||||
| CcienaCesOamConfigRevision | 1.3.6.1.4.1.1271.2.3.5.1.1.4.1.6 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current The configuration revision of the OAM entity as reflected in the latest OAMPDU sent by the OAM entity. The configuration revision is used by OAM entities to indicate configuration changes have occurred which might require the peer OAM entity to re-evaluate whether the peering is allowed. See local_satisfied in [802.3ah, 57.3.1.2]. | ||||
| CcienaCesOamFunctionsSupported | 1.3.6.1.4.1.1271.2.3.5.1.1.4.1.7 | Bits | RO | |
column · Bits · read-only · current The OAM functions supported on this Ethernet like interface. OAM consists of separate functional sets beyond the basic discovery process which is always required. These functional groups can be supported independently by any implementation. These values are communicated to the peer via the local configuration field of Information OAMPDUs.
| ||||
| CcienaCesOamPduTimer | 1.3.6.1.4.1.1271.2.3.5.1.1.4.1.8 | INTEGER (100..1000) | RO | |
column · INTEGER (100..1000) · read-only · current The time in milliseconds between Information OAMPDUs being transmitted via the Ethernet port.
| ||||
| CcienaCesOamLinkLostTimer | 1.3.6.1.4.1.1271.2.3.5.1.1.4.1.9 | INTEGER (500..5000) | RO | |
column · INTEGER (500..5000) · read-only · current The time in milliseconds to wait for an Information OAMPDU via the Ethernet port, from a peer, before declaring the link lost.
| ||||
| TcienaCesOamPeerTable | 1.3.6.1.4.1.1271.2.3.5.1.1.5 | NA | ||
table · not-accessible · current Information about the OAM peer for a particular Ethernet like interface. OAM entities communicate with a single OAM peer entity on full-duplex Ethernet links on which OAM is enabled and operating properly. In certain states, the OAM peer information is not available. Whether peer information is available is communicated via the cienaCesOamPeerStatus object. When this object is inactive, all other information in the row is considered invalid. | ||||
| RcienaCesOamPeerEntry | 1.3.6.1.4.1.1271.2.3.5.1.1.5.1 | NA | ||
row · not-accessible · current An entry in the table, containing information on the peer OAM entity for a single Ethernet like interface. Note that there is at most one OAM peer for each Ethernet like interface. There is exactly one row in this table for each Ethernet like interface supporting OAM.
| ||||
| CcienaCesOamLocalPort | 1.3.6.1.4.1.1271.2.3.5.1.1.5.1.1 | Integer32 | NA | |
column · Integer32 · not-accessible · current An Ethernet port on the local switch. | ||||
| CcienaCesOamPeerStatus | 1.3.6.1.4.1.1271.2.3.5.1.1.5.1.2 | INTEGER | RO | |
column · INTEGER · read-only · current This object indicates whether the information in this row should be considered valid. When active(1), the information is valid and represents the current peer of the OAM entity. When inactive(2), the information in this row is invalid. A value of inactive(2) is returned if the cienaCesOamOperStatus is disabled, passiveWait, or activeSendLocal. For all other values of cienaCesOamOperStatus, a value of active(1) is returned.
| ||||
| CcienaCesOamPeerMacAddress | 1.3.6.1.4.1.1271.2.3.5.1.1.5.1.3 | OCTET STRING (SIZE (6)) | RO | |
column · OCTET STRING (SIZE (6)) · read-only · current The MAC address of the peer OAM entity. The MAC address is derived from the most recently received OAMPDU. This value is initialized to all zeros (0x000000000000). This value is invalid if the cienaCesOamPeerStatus is inactive. An OAMPDU is indicated by a valid frame with (1) destination MAC address equal to that of the reserved MAC address for Slow Protocols (See 43B of [802.3ah]), (2) a lengthOrType field equal to the reserved type for Slow Protocols, (3) and a Slow Protocols subtype equal to that of the subtype reserved for OAM. | ||||
| CcienaCesOamPeerVendorOui | 1.3.6.1.4.1.1271.2.3.5.1.1.5.1.4 | OCTET STRING (SIZE (3)) | RO | |
column · OCTET STRING (SIZE (3)) · read-only · current The OUI of the OAM peer as reflected in the latest
Information OAMPDU received with a Local Information TLV. The
OUI can be used to identify the vendor of the remote OAM
entity. This value is initialized to all zeros (0x000000).
This value is considered invalid if the cienaCesOamPeerStatus is
inactive.
An Information OAMPDU is indicated by a valid frame with (1)
destination MAC address equal to that of the reserved MAC
address for Slow Protocols (See 43B of [802.3ah]), (2) a
lengthOrType field equal to the reserved type for Slow Protocols, (3)
a Slow Protocols subtype equal to that of the
subtype reserved for OAM, and (4) an OAM code that equals the code
reserved for Information OAMPDUs. | ||||
| CcienaCesOamPeerVendorInfo | 1.3.6.1.4.1.1271.2.3.5.1.1.5.1.5 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current The Vendor Info of the OAM peer as reflected in the latest
Information OAMPDU received with a Local Information TLV. The
vendor information field is within the Local Information TLV,
and can be used to determine additional information about the
peer entity. The format of the vendor information is
unspecified within the 32-bit field. This value is initialized
to all zero. This value is invalid if the cienaCesOamPeerStatus
is inactive.
An Information OAMPDU is indicated by a valid frame with (1)
destination MAC address equal to that of the reserved MAC
address for Slow Protocols (See 43B of [802.3ah]), (2) a
lengthOrType field equal to the reserved type for Slow
Protocols, (3) a Slow Protocols subtype equal to that of the
subtype reserved for OAM, and (4) an OAM code that equals the
code reserved for Information OAMPDUs. | ||||
| CcienaCesOamPeerMode | 1.3.6.1.4.1.1271.2.3.5.1.1.5.1.6 | INTEGER | RO | |
column · INTEGER · read-only · current The mode of the OAM peer as reflected in the latest Information OAMPDU received with a Local Information TLV. The mode of the peer can be determined from the Configuration field in the Local Information TLV of the last Information OAMPDU received from the peer. This value is initialized to unknown(3), and is not valid if the cienaCesOamPeerStatus is inactive. An Information OAMPDU is indicated by a valid frame with (1) destination MAC address equal to that of the reserved MAC address for Slow Protocols (See 43B of [802.3ah]), (2) a lengthOrType field equal to the reserved type for Slow Protocols, (3) a Slow Protocols subtype equal to that of the subtype reserved for OAM, and (4) an OAM code that equals the code reserved for Information OAMPDUs.
| ||||
| CcienaCesOamPeerMaxOamPduSize | 1.3.6.1.4.1.1271.2.3.5.1.1.5.1.7 | Integer32 | RO | |
column · Integer32 · read-only · current The maximum size of OAMPDU supported by the peer as reflected in the latest Information OAMPDU received with a Local Information TLV. Ethernet OAM on this interface must not use OAMPDUs that exceed this size. The maximum OAMPDU size can be determined from the PDU Configuration field of the Local Information TLV of the last Information OAMPDU received from the peer. This value is initialized to 64, and is invalid if the cienaCesOamPeerStatus is inactive. An Information OAMPDU is indicated by a valid frame with (1) destination MAC address equal to that of the reserved MAC address for Slow Protocols (See 43B of [802.3ah]), (2) a lengthOrType field equal to the reserved type for Slow Protocols, (3) a Slow Protocols subtype equal to that of the subtype reserved for OAM, and (4) an OAM code that equals the code reserved for Information OAMPDUs.
| ||||
| CcienaCesOamPeerConfigRevision | 1.3.6.1.4.1.1271.2.3.5.1.1.5.1.8 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current The configuration revision of the OAM peer as reflected in
the latest OAMPDU. This attribute is changed by the peer
whenever it has a local configuration change for Ethernet OAM
this interface. This value is initialized to zero,
and is invalid if the cienaCesOamPeerStatus is
inactive.
The configuration revision can be determined from the Revision
field of the Local Information TLV of the most recently
received Information OAMPDU with a Local Information TLV.
An Information OAMPDU is indicated by a valid frame with (1)
destination MAC address equal to that of the reserved MAC
address for Slow Protocols (See 43B of [802.3ah]), (2) a
lengthOrType field equal to the reserved type for Slow
Protocols, (3) a Slow Protocols subtype equal to that of the
subtype reserved for OAM, and (4) an OAM code that equals the
code reserved for Information OAMPDUs. | ||||
| CcienaCesOamPeerFunctionsSupported | 1.3.6.1.4.1.1271.2.3.5.1.1.5.1.9 | Bits | RO | |
column · Bits · read-only · current The OAM functions supported on this Ethernet like interface. OAM consists of separate functionality sets above the basic discovery process. This value indicates the capabilities of the peer OAM entity with respect to these functions. This value is initialized so all bits are clear, and is invalid if the cienaCesOamPeerStatus is inactive. The capbilities of the OAM peer can be determined from the configuration field of the Local Information TLV of the most recently received Information OAMPDU with a Local Information TLV. An Information OAMPDU is indicated by a valid frame with (1) destination MAC address equal to that of the reserved MAC address for Slow Protocols (See 43B of [802.3ah]), (2) a lengthOrType field equal to the reserved type for Slow Protocols, (3) a Slow Protocols subtype equal to that of the subtype reserved for OAM, and (4) an OAM code that equals the code reserved for Information OAMPDUs.
| ||||
| TcienaCesOamLoopbackTable | 1.3.6.1.4.1.1271.2.3.5.1.1.6 | NA | ||
table · not-accessible · current This table contains methods to control the loopback state of the local link as well as indicating the status of the loopback function. Loopback can be used to place the remote OAM entity in a state where every received frame (except OAMPDUs) are echoed back over the same interface on which they were received. In this state, at the remote entity, 'normal' traffic is disabled as only the looped back frames are transmitted on the interface. Loopback is thus an intrusive operation that prohibits normal data flow and should be used accordingly. | ||||
| RcienaCesOamLoopbackEntry | 1.3.6.1.4.1.1271.2.3.5.1.1.6.1 | NA | ||
row · not-accessible · current An entry in the table, containing information on the loopback status for a single Ethernet like interface. There is an entry in this table for every Ethernet like interface which supports OAM and loopback function within OAM (as indicated in cienaCesOamFunctionsSupported). | ||||
| CcienaCesOamLoopbackPort | 1.3.6.1.4.1.1271.2.3.5.1.1.6.1.1 | Integer32 | NA | |
column · Integer32 · not-accessible · current An Ethernet port on the switch. | ||||
| CcienaCesOamLoopbackCommand | 1.3.6.1.4.1.1271.2.3.5.1.1.6.1.2 | INTEGER | RO | |
column · INTEGER · read-only · current This attribute initiates or terminates remote loopback with an OAM peer. Value startRemoteLoopback(2) of this attribute indicates the local OAM client to send a loopback OAMPDU to the OAM peer with the loopback enable flags set. Value stopRemoteLoopback(3) of this attribute indicates the local OAM client to send a loopback OAMPDU to the OAM peer with the loopback enable flags cleared. Value noLoopback(1) to this attribute has no effect. The attribute always returns noLoopback on a read. To determine the loopback status, use the attribute cienaCesOamLoopbackStatus.
| ||||
| CcienaCesOamLoopbackStatus | 1.3.6.1.4.1.1271.2.3.5.1.1.6.1.3 | INTEGER | RO | |
column · INTEGER · read-only · current The loopback status of the OAM entity. This status is
determined by a combination of the local parser and
multiplexer states, the remote parser and multiplexer states,
as well as by the actions of the local OAM client. When
operating in normal mode with no loopback in progress, the
status reads noLoopback(1).
If the OAM client has sent a Loopback OAMPDU and is waiting
for a response, where the local parser and multiplexer states
are DISCARD (see [802.3ah, 57.2.11.1]), the status is
'initiatingLoopback'. In this case, the local OAM entity has
yet to receive any acknowledgement that the remote OAM entity
has received its loopback command request.
If the local OAM client knows that the remote OAM entity is in
loopback mode (via the remote state information as described
in [802.3ah, 57.2.11.1, 30.3.6.1.15]), the status is remoteLoopback(3).
If the local OAM client is in the process
of terminating the remote loopback [802.3ah, 57.2.11.3,
30.3.6.1.14], with its local multiplexer and parser states in
DISCARD, the status is terminatingLoopback(4). If the remote
OAM client has put the local OAM entity in loopback mode as
indicated by its local parser state, the status is
localLoopback(5).
The unknown(6) status indicates the parser and multiplexer
combination is unexpected. This status may be returned if the
OAM loopback is in a transition state but should not persist.
The values of this attribute correspond to the following
values of the local and remote parser and multiplexer states.
LclPrsr LclMux RmtPrsr RmtMux
noLoopback FWD FWD FWD FWD
initLoopback DISCARD DISCARD FWD FWD
rmtLoopback DISCARD FWD LPBK DISCARD
tmtngLoopback DISCARD DISCARD LPBK DISCARD
lclLoopback LPBK DISCARD DISCARD FWD
unknown *** any other combination ***
| ||||
| CcienaCesOamLoopbackIgnoreRx | 1.3.6.1.4.1.1271.2.3.5.1.1.6.1.4 | INTEGER | RO | |
column · INTEGER · read-only · current Since OAM loopback is a disruptive operation (user traffic does not pass), this attribute provides a mechanism to provide controls over whether received OAM loopback commands are processed or ignored. When the value is ignore(1), received loopback commands are ignored. When the value is process(2), OAM loopback commands are processed. The default value is to ignore loopback commands (ignore(1)). The attribute has no meaning if the local OAM entity does not support the loopback function (as defined in cienaCesOamFunctionsSupported).
| ||||
| ScienaCesOamSystemEnableDisable | 1.3.6.1.4.1.1271.2.3.5.1.1.7 | INTEGER | RO | |
scalar · INTEGER · read-only · current This object indicates the administratively configurable state of the OAM on the switch.
| ||||
| TcienaCesOamEventConfigTable | 1.3.6.1.4.1.1271.2.3.5.1.1.8 | NA | ||
table · not-accessible · current Ethernet OAM includes the ability to generate and receive
event notifications to indicate various link problems. This
table contains the mechanisms to configure the thresholds to
generate the standard Ethernet OAM Event.
These events are:
- Errored Symbol Period Event. Generated when the number of
symbol errors exceeds a threshold within a given window
defined by a number of symbols (e.g. 1,000 symbols out of
1,000,000 had errors).
- Errored Frame Period Event. Generated when the number of
frame errors exceeds a threshold within a given window
defined by a number of frames (e.g. 10 frames out of 1000
had errors).
- Errored Frame Event. Generated when the number of frame
errors exceeds a threshold within a given window defined
by a period of time (e.g. 10 frames in 1 second had
errors).
- Errored Frame Seconds Summary Event. Generated when the
number of errored frame seconds exceeds a threshold within
a given time period (e.g. 10 errored frame seconds within
the last 100 seconds). An errored frame second is defined
as a 1 second interval that had >0 frame errors. | ||||
| RcienaCesOamEventConfigEntry | 1.3.6.1.4.1.1271.2.3.5.1.1.8.1 | NA | ||
row · not-accessible · current Event configuration information is available for every Ethernet like interface that supports OAM and the event function of OAM as indicated in the cienaCesOamFunctionsSupported attribute. Event configuration controls when the local management entity sends Event Notification OAMPDUs to its OAM peer.
| ||||
| CcienaCesOamEventPort | 1.3.6.1.4.1.1271.2.3.5.1.1.8.1.1 | Integer32 | NA | |
column · Integer32 · not-accessible · current An Ethernet port on the switch | ||||
| CcienaCesOamErrFramePeriodWindow | 1.3.6.1.4.1.1271.2.3.5.1.1.8.1.2 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current The number of frames over which the threshold is defined. The default value of the window is the number of minimum size Ethernet frames that can be received over the physical layer in one second. If cienaCesOamErrFramePeriodThreshold frame errors occur within a window of cienaCesOamErrFramePeriodWindow frames, an Event Notification OAMPDU should be generated with an Errored Frame Period Event TLV indicating the threshold has been crossed in this window. +------------ Range of errd-frame-period-window values------------+ | 10 mbps link : 1488 - 892800 | | 100 mbps link : 14880 - 8928000 | | 1000 mbps link : 148810 - 89285760 | | 10000 mbps link : 1488096 - 892857120 | +-----------------------------------------------------------------+
| ||||
| CcienaCesOamErrFramePeriodThreshold | 1.3.6.1.4.1.1271.2.3.5.1.1.8.1.3 | Unsigned32 (0..4294967293) | RO | |
column · Unsigned32 (0..4294967293) · read-only · current The number of frame errors that must occur for this event to be triggered. The default value is one frame error. If cienaCesOamErrFramePeriodThreshold frame errors occur within a window of cienaCesOamErrFramePeriodWindow frames, an Event Notification OAMPDU should be generated with an Errored Frame Period Event TLV indicating the threshold has been crossed in this window.
| ||||
| CcienaCesOamErrFramePeriodEvNotifEnable | 1.3.6.1.4.1.1271.2.3.5.1.1.8.1.4 | INTEGER | RO | |
column · INTEGER · read-only · current Indicates whether the occurrence of an Errored Frame Period Event should result in an Event Notification OAMPDU generated by the OAM layer. By default, this object should have the value enabled(1) for Ethernet like interfaces that support OAM. If the OAM layer does not support event notifications (as indicated via the cienaCesOamFunctionsSupported attribute), this value is ignored.
| ||||
| CcienaCesOamErrFrameWindow | 1.3.6.1.4.1.1271.2.3.5.1.1.8.1.5 | Unsigned32 (10..600) | RO | |
column · Unsigned32 (10..600) · read-only · current The amount of time (in 100ms increments) over which the threshold is defined. The default value is 10 (1 second). If cienaCesOamErrFrameThreshold frame errors occur within a window of cienaCesOamErrFrameWindow seconds (measured in tenths of seconds), an Event Notification OAMPDU should be generated with an Errored Frame Event TLV indicating the threshold has been crossed in this window.
| ||||
| CcienaCesOamErrFrameThreshold | 1.3.6.1.4.1.1271.2.3.5.1.1.8.1.6 | Unsigned32 (0..4294967293) | RO | |
column · Unsigned32 (0..4294967293) · read-only · current The number of frame errors that must occur for this event to be triggered. The default value is one frame error. If cienaCesOamErrFrameThreshold frame errors occur within a window of cienaCesOamErrFrameWindow (in tenths of seconds), an Event Notification OAMPDU should be generated with an Errored Frame Event TLV indicating the threshold has been crossed in this window.
| ||||
| CcienaCesOamErrFrameEvNotifEnable | 1.3.6.1.4.1.1271.2.3.5.1.1.8.1.7 | INTEGER | RO | |
column · INTEGER · read-only · current Indicates whether the occurrence of an Errored Frame Event should result in an Event Notification OAMPDU generated by the OAM layer. By default, this object should have the value enabled(1) for Ethernet like interfaces that support OAM. If the OAM layer does not support event notifications (as indicated via the cienaCesOamFunctionsSupported attribute), this value is ignored.
| ||||
| CcienaCesOamErrFrameSecsSummaryWindow | 1.3.6.1.4.1.1271.2.3.5.1.1.8.1.8 | Integer32 (100..9000) | RO | |
column · Integer32 (100..9000) · read-only · current The amount of time (in 100ms intervals) over which the threshold is defined. The default value is 100 (10 seconds). If cienaCesOamErrFrameSecsSummaryThreshold frame errors occur within a window of cienaCesOamErrFrameSecsSummaryWindow (in tenths of seconds), an Event Notification OAMPDU should be generated with an Errored Frame Seconds Summary Event TLV indicating the threshold has been crossed in this window.
| ||||
| CcienaCesOamErrFrameSecsSummaryThreshold | 1.3.6.1.4.1.1271.2.3.5.1.1.8.1.9 | Integer32 (0..65535) | RO | |
column · Integer32 (0..65535) · read-only · current The number of errored frame seconds that must occur for this event to be triggered. The default value is one errored frame second. If cienaCesOamErrFrameSecsSummaryThreshold frame errors occur within a window of cienaCesOamErrFrameSecsSummaryWindow (in tenths of seconds), an Event Notification OAMPDU should be generated with an Errored Frame Seconds Summary Event TLV indicating the threshold has been crossed in this window.
| ||||
| CcienaCesOamErrFrameSecsEvNotifEnable | 1.3.6.1.4.1.1271.2.3.5.1.1.8.1.10 | INTEGER | RO | |
column · INTEGER · read-only · current Indicates whether the occurrence of an Errored Frame Seconds Summary Event should result in an Event Notification OAMPDU generated by the OAM layer. By default, this object should have the value enabled(1) for Ethernet like interfaces that support OAM. If the OAM layer does not support event notifications (as indicated via the cienaCesOamFunctionsSupported attribute), this value is ignored.
| ||||
| CcienaCesOamDyingGaspEnable | 1.3.6.1.4.1.1271.2.3.5.1.1.8.1.11 | INTEGER | RO | |
column · INTEGER · read-only · current Indicates whether the local device should attempt to indicate a dying gasp fault via the OAMPDU flags field to its peer OAM entity. If the system does not support dying gasp capability, reading the object should always result in 'disabled(2)'. By default, this object should have the value enabled(1) for Ethernet like interfaces that support OAM. If the OAM layer does not support event notifications (as indicated via the OamFunctionsSupported attribute), this value is ignored.
| ||||
| CcienaCesOamCriticalEventEnable | 1.3.6.1.4.1.1271.2.3.5.1.1.8.1.12 | INTEGER | RO | |
column · INTEGER · read-only · current Indicates whether the local device should attempt to indicate a critical event has occurred via the OAMPDU flags field to its peer OAM entity. If the system does not support dying gasp capability, reading the object should always result in 'disabled(2)'. By default, this object should have the value enabled(1) for Ethernet like interfaces that support OAM. If the OAM layer does not support event notifications (as indicated via the OamFunctionsSupported attribute), this value is ignored.
| ||||
| NcienaCesOamConformance | 1.3.6.1.4.1.1271.2.3.5.1.2 | |||
| NcienaCesOamCompliances | 1.3.6.1.4.1.1271.2.3.5.1.2.1 | |||
| NcienaCesOamGroups | 1.3.6.1.4.1.1271.2.3.5.1.2.2 | |||
Traps / Notifications
- cienaCesOamLinkEventTrap
1.3.6.1.4.1.1271.2.2.15.0.1