CIENA-CES-BENCHMARK-MIB
Ciena CorporationThe MIB module for managing RFC2544/Y1564 service benchmark testing.
snmptranslate -m CIENA-CES-BENCHMARK-MIB -Tpsnmpwalk -v2c -c <community> -m CIENA-CES-BENCHMARK-MIB <host> 1.3.6.1.4.1.1271.2.1.39Imports
| CIENA-GLOBAL-MIB | cienaGlobalMacAddress, cienaGlobalSeverity |
|---|---|
| CIENA-SMI | cienaCesConfig, cienaCesNotifications, cienaCesStatistics |
| INET-ADDRESS-MIB | InetAddress, InetAddressPrefixLength, InetAddressType |
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP |
| SNMPv2-SMI | Bits, Counter64, Integer32, IpAddress, MODULE-IDENTITY, MibIdentifier, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, iso |
| SNMPv2-TC | DateAndTime, DisplayString, MacAddress, PhysAddress, RowStatus, TEXTUAL-CONVENTION, TruthValue |
OID tree
| Name | OID | Type | Access | Status |
|---|---|---|---|---|
| IcienaCesBenchmarkMIB | 1.3.6.1.4.1.1271.2.1.39 | |||
identity The MIB module for managing RFC2544/Y1564 service benchmark testing. | ||||
| NcienaCesBenchmarkMIBObjects | 1.3.6.1.4.1.1271.2.1.39.1 | |||
| NcienaCesBenchmarkModule | 1.3.6.1.4.1.1271.2.1.39.1.1 | |||
| NcienaCesBenchmarkGlobalObjects | 1.3.6.1.4.1.1271.2.1.39.1.1.1 | |||
| ScienaCesBenchmarkGlobalAdminState | 1.3.6.1.4.1.1271.2.1.39.1.1.1.1 | CienaCesBenchmarkAdminState | RW | |
scalar · CienaCesBenchmarkAdminState · read-write · current Administrative state of the benchmark feature at the global level. | ||||
| ScienaCesBenchmarkGlobalGeneratorDefaultEmixSequenceId | 1.3.6.1.4.1.1271.2.1.39.1.1.1.2 | Integer32 (0..32) | RW | |
scalar · Integer32 (0..32) · read-write · current Default EMIX sequence to be used on a test instance when no EMIX is specified in the test instance targeted test profile. This applies to generator test instances only. | ||||
| ScienaCesBenchmarkGlobalGeneratorDefaultKpiProfileId | 1.3.6.1.4.1.1271.2.1.39.1.1.1.3 | Integer32 (0..32) | RW | |
scalar · Integer32 (0..32) · read-write · current Default KPI profile to be used to analyze the results of a test instance when no KPI profile is specifed in the targeted test profile. This applies to generator test instances only. | ||||
| ScienaCesBenchmarkGlobalGeneratorDefaultBwAllocProfileId | 1.3.6.1.4.1.1271.2.1.39.1.1.1.4 | Integer32 (0..32) | RW | |
scalar · Integer32 (0..32) · read-write · current Default bandwidth allocation profile to be used with a test instance when no bandwidth allocation profile is specified in the targeted test profile. This applies to generator test instances only. | ||||
| ScienaCesBenchmarkGlobalPlatformMaxConfigEntities | 1.3.6.1.4.1.1271.2.1.39.1.1.1.5 | Integer32 | RO | |
scalar · Integer32 · read-only · current Maximum number of entities that can be created on this platform. | ||||
| ScienaCesBenchmarkGlobalPlatformMaxConfigTestInstances | 1.3.6.1.4.1.1271.2.1.39.1.1.1.6 | Integer32 | RO | |
scalar · Integer32 · read-only · current Maximum number of test instances that can be created on this platform. | ||||
| ScienaCesBenchmarkGlobalPlatformMaxConfigTestProfiles | 1.3.6.1.4.1.1271.2.1.39.1.1.1.7 | Integer32 | RO | |
scalar · Integer32 · read-only · current Maximum number of test profiles that can be created on this platform. | ||||
| ScienaCesBenchmarkGlobalPlatformMaxConfigKpiProfiles | 1.3.6.1.4.1.1271.2.1.39.1.1.1.8 | Integer32 | RO | |
scalar · Integer32 · read-only · current Maximum number of KPI profiles that can be created on this platform. | ||||
| ScienaCesBenchmarkGlobalPlatformMaxConfigBwAllocProfiles | 1.3.6.1.4.1.1271.2.1.39.1.1.1.9 | Integer32 | RO | |
scalar · Integer32 · read-only · current Maximum number of bandwidth distribution profiles that can be created on this platform. | ||||
| ScienaCesBenchmarkGlobalPlatformMaxConfigEmixSequences | 1.3.6.1.4.1.1271.2.1.39.1.1.1.10 | Integer32 | RO | |
scalar · Integer32 · read-only · current Maximum number of EMIX sequences that can be created on this platform, including the system created ones. | ||||
| ScienaCesBenchmarkGlobalPlatformMaxSimultaneousRunningTests | 1.3.6.1.4.1.1271.2.1.39.1.1.1.11 | Integer32 | RO | |
scalar · Integer32 · read-only · current Maximum number of test instances that can be running simultaneously on this platform. | ||||
| ScienaCesBenchmarkGlobalConfiguredEntities | 1.3.6.1.4.1.1271.2.1.39.1.1.1.12 | Integer32 | RO | |
scalar · Integer32 · read-only · current Number of entities currently configured. | ||||
| ScienaCesBenchmarkGlobalConfiguredTestInstances | 1.3.6.1.4.1.1271.2.1.39.1.1.1.13 | Integer32 | RO | |
scalar · Integer32 · read-only · current Number of test instances currently configured. | ||||
| ScienaCesBenchmarkGlobalConfiguredProfiles | 1.3.6.1.4.1.1271.2.1.39.1.1.1.14 | Integer32 | RO | |
scalar · Integer32 · read-only · current Number of test profiles currently configured. | ||||
| ScienaCesBenchmarkGlobalConfiguredEmixSequences | 1.3.6.1.4.1.1271.2.1.39.1.1.1.15 | Integer32 | RO | |
scalar · Integer32 · read-only · current Number of EMIX sequences currently configured, including the system created ones. | ||||
| ScienaCesBenchmarkGlobalConfiguredKpiProfiles | 1.3.6.1.4.1.1271.2.1.39.1.1.1.16 | Integer32 | RO | |
scalar · Integer32 · read-only · current Number of KPI profiles currently configured. | ||||
| ScienaCesBenchmarkGlobalConfiguredBwAllocProfiles | 1.3.6.1.4.1.1271.2.1.39.1.1.1.17 | Integer32 | RO | |
scalar · Integer32 · read-only · current Number of bandwidth distribution profiles currently configured. | ||||
| ScienaCesBenchmarkGlobalEnabledTestInstances | 1.3.6.1.4.1.1271.2.1.39.1.1.1.18 | Integer32 | RO | |
scalar · Integer32 · read-only · current Number of test instances currently enabled across the platform. | ||||
| ScienaCesBenchmarkGlobalGeneratorRunningTestInstances | 1.3.6.1.4.1.1271.2.1.39.1.1.1.19 | Integer32 | RO | |
scalar · Integer32 · read-only · current Number of generator test instances currently running across the platform. | ||||
| TcienaCesBenchmarkEntityTable | 1.3.6.1.4.1.1271.2.1.39.1.1.2 | NA | ||
table · not-accessible · current Table of benchmark entity entries. | ||||
| RcienaCesBenchmarkEntityEntry | 1.3.6.1.4.1.1271.2.1.39.1.1.2.1 | NA | ||
| CcienaCesBenchmarkEntityEntryId | 1.3.6.1.4.1.1271.2.1.39.1.1.2.1.1 | Integer32 | NA | |
column · Integer32 · not-accessible · current Entity unique ID | ||||
| CcienaCesBenchmarkEntityEntryName | 1.3.6.1.4.1.1271.2.1.39.1.1.2.1.2 | DisplayString (SIZE (1..46)) | RC | |
column · DisplayString (SIZE (1..46)) · read-create · current Name of the benchmark entity as entered when created. | ||||
| CcienaCesBenchmarkEntityEntryRole | 1.3.6.1.4.1.1271.2.1.39.1.1.2.1.3 | INTEGER | RC | |
column · INTEGER · read-create · current Entity role
| ||||
| CcienaCesBenchmarkEntityEntryPortId | 1.3.6.1.4.1.1271.2.1.39.1.1.2.1.4 | Integer32 (1..65535) | RC | |
column · Integer32 (1..65535) · read-create · current Entity port under test | ||||
| CcienaCesBenchmarkEntityEntryMode | 1.3.6.1.4.1.1271.2.1.39.1.1.2.1.5 | INTEGER | RC | |
column · INTEGER · read-create · current Entity mode
| ||||
| CcienaCesBenchmarkEntityEntryAdminState | 1.3.6.1.4.1.1271.2.1.39.1.1.2.1.6 | CienaCesBenchmarkAdminState | RC | |
column · CienaCesBenchmarkAdminState · read-create · current Entity admin state. | ||||
| CcienaCesBenchmarkEntityEntryLocalMac | 1.3.6.1.4.1.1271.2.1.39.1.1.2.1.7 | MacAddress | RO | |
column · MacAddress · read-only · current The FPGA internal test port assigned mac address. | ||||
| CcienaCesBenchmarkEntityEntrySlotId | 1.3.6.1.4.1.1271.2.1.39.1.1.2.1.8 | Integer32 | RO | |
column · Integer32 · read-only · current The slot Id of the line module associated with this entity. | ||||
| CcienaCesBenchmarkEntityEntryReflectorVendorType | 1.3.6.1.4.1.1271.2.1.39.1.1.2.1.9 | INTEGER | RC | |
column · INTEGER · read-create · current Indicator as to what type of equipment is generating the test traffic on the remote end.
| ||||
| CcienaCesBenchmarkEntityEntryReflectionLevel | 1.3.6.1.4.1.1271.2.1.39.1.1.2.1.10 | INTEGER | RC | |
column · INTEGER · read-create · current For reflector entities, this indicates the minimum reflection level required. If test traffic is going over an ethernet L2 cloud, l2-only is fine. But if the test traffic is going over an IP network, the reflector needs to be able to swap L2 and L3 fields. Depending on the type of IP network, the user needs to configured IPv4 or IPv6. L2 to L4 will swap MAC addresses, IP addresses and src and destination L4 port. Depending on the reflection level required, a different device is used to implement the reflector.
| ||||
| CcienaCesBenchmarkEntityEntryGeneratorHFrameSize | 1.3.6.1.4.1.1271.2.1.39.1.1.2.1.11 | Integer32 (64..9216) | RC | |
column · Integer32 (64..9216) · read-create · current Maximum frame size that should be generated by the generator device. This H frame size should to leave enough room for extra encapsulation bytes that will be pushed onto the packet by the switch when pushing this test packet out the network side port. The generator device will ensure that any frame size list or EMIX used during the test is adjusted accordingly | ||||
| CcienaCesBenchmarkEntityEntryMaxConfigTestInstances | 1.3.6.1.4.1.1271.2.1.39.1.1.2.1.12 | Integer32 | RO | |
column · Integer32 · read-only · current Maximum number of test instances that can be configured on this entity. | ||||
| CcienaCesBenchmarkEntityEntryMaxSimultaneousTestInstances | 1.3.6.1.4.1.1271.2.1.39.1.1.2.1.13 | Integer32 | RO | |
column · Integer32 · read-only · current Maximum number of test instances that can be enabled (reflector) or running (generator) on this entity, given the availability of hw sessions. | ||||
| CcienaCesBenchmarkEntityEntryOperEnabled | 1.3.6.1.4.1.1271.2.1.39.1.1.2.1.14 | TruthValue | RO | |
column · TruthValue · read-only · current Entity operational enable/disable. An entity is operationally enabled when the feature is enabled, the entity is enabled and at least one test instance associated with that entity is enabled (reflector) or running (generator) | ||||
| CcienaCesBenchmarkEntityEntryNumTestInstancesConfigured | 1.3.6.1.4.1.1271.2.1.39.1.1.2.1.15 | Integer32 | RO | |
column · Integer32 · read-only · current Number of test instances currently configured on this entity. | ||||
| CcienaCesBenchmarkEntityEntryNumTestInstancesEnabled | 1.3.6.1.4.1.1271.2.1.39.1.1.2.1.16 | Integer32 | RO | |
column · Integer32 · read-only · current Number of test instances currently enabled. | ||||
| CcienaCesBenchmarkEntityEntryGenNumTestInstancesRunning | 1.3.6.1.4.1.1271.2.1.39.1.1.2.1.17 | Integer32 | RO | |
column · Integer32 · read-only · current Number of test instances currently running. | ||||
| CcienaCesBenchmarkEntityEntryBwAvailable | 1.3.6.1.4.1.1271.2.1.39.1.1.2.1.18 | Integer32 | RO | |
column · Integer32 · read-only · current Bandwidth available for test traffic if a reflector. Bandwidth remaining for other test instances to be started if a generator. | ||||
| CcienaCesBenchmarkEntityEntryGenBwUsedByRunningTests | 1.3.6.1.4.1.1271.2.1.39.1.1.2.1.19 | Integer32 | RO | |
column · Integer32 · read-only · current Bandwidth currently used by test instances currently running, in Mbps. | ||||
| CcienaCesBenchmarkEntityEntryAvailableHwSessions | 1.3.6.1.4.1.1271.2.1.39.1.1.2.1.20 | Integer32 | RO | |
column · Integer32 · read-only · current Maximum number of simultaneous hardware sessions available on this platform. | ||||
| CcienaCesBenchmarkEntityEntryAllocatedHwSessions | 1.3.6.1.4.1.1271.2.1.39.1.1.2.1.21 | Integer32 | RO | |
column · Integer32 · read-only · current The number of allocated hardware sessions | ||||
| CcienaCesBenchmarkEntityEntryRowStatus | 1.3.6.1.4.1.1271.2.1.39.1.1.2.1.22 | RowStatus | RC | |
column · RowStatus · read-create · current Used to manage the creation and deletion of the conceptual rows in this table. To create a row in this table, set this object to 'createAndGo'. To delete a row in this table, set this object to 'destroy'. If the entry exists, it is displayed as 'active'. | ||||
| CcienaCesBenchmarkEntityEntryClearStats | 1.3.6.1.4.1.1271.2.1.39.1.1.2.1.23 | TruthValue | RC | |
column · TruthValue · read-create · current Set to true to clear all global fpga counters for the given entity. Clear is only allowed for a reflector if no test instances are enabled, and for a generator if no test instances are running. The value is reset to false once the transaction is completed. | ||||
| CcienaCesBenchmarkEntityEntryReflectorMacValidation | 1.3.6.1.4.1.1271.2.1.39.1.1.2.1.24 | TruthValue | RC | |
column · TruthValue · read-create · current This attribute is only valid for the reflector entity and indicates whether the reflector verifies that the destination MAC of the test frames matches the MAC address associated with benchamrk reflector entity. MAC Validation can only be disabled (False) in out-if-service or evc/vid-out-of-service mode. | ||||
| TcienaCesBenchmarkEntityStatsTable | 1.3.6.1.4.1.1271.2.1.39.1.1.3 | NA | ||
table · not-accessible · current Table of benchmark entity statistics entries. | ||||
| RcienaCesBenchmarkEntityStatsEntry | 1.3.6.1.4.1.1271.2.1.39.1.1.3.1 | NA | ||
| CcienaCesBenchmarkEntityStatsEntryClear | 1.3.6.1.4.1.1271.2.1.39.1.1.3.1.1 | TruthValue | RW | obsolete |
column · TruthValue · read-write · obsolete Set to true to clear all port and/or global fpga counters for the given entity. Clear is only allowed for a reflector if no test instances are enabled, and for a generator if no test instances are running. The value is reset to False once the transaction is completed. This has been obsoleted by cienaCesBenchmarkEntityEntryClearStats. | ||||
| CcienaCesBenchmarkEntityStatsEntryPortTxBytes | 1.3.6.1.4.1.1271.2.1.39.1.1.3.1.2 | Counter64 | RO | |
column · Counter64 · read-only · current Number of bytes transmitted by the benchmark port | ||||
| CcienaCesBenchmarkEntityStatsEntryPortTxPkts | 1.3.6.1.4.1.1271.2.1.39.1.1.3.1.3 | Counter64 | RO | |
column · Counter64 · read-only · current Number of packets transmitted by the benchmark port | ||||
| CcienaCesBenchmarkEntityStatsEntryPortTxCrcErrorPkts | 1.3.6.1.4.1.1271.2.1.39.1.1.3.1.4 | Counter64 | RO | |
column · Counter64 · read-only · current Number of packets with CRC errors | ||||
| CcienaCesBenchmarkEntityStatsEntryPortTxUcastPkts | 1.3.6.1.4.1.1271.2.1.39.1.1.3.1.5 | Counter64 | RO | |
column · Counter64 · read-only · current Number of unicast packets transmitted by the benchmark port | ||||
| CcienaCesBenchmarkEntityStatsEntryPortTxMcastPkts | 1.3.6.1.4.1.1271.2.1.39.1.1.3.1.6 | Counter64 | RO | |
column · Counter64 · read-only · current Number of multicast packets transmitted by the benchmark port | ||||
| CcienaCesBenchmarkEntityStatsEntryPortTxBcastPkts | 1.3.6.1.4.1.1271.2.1.39.1.1.3.1.7 | Counter64 | RO | |
column · Counter64 · read-only · current Number of broadcast packets transmitted by the benchmark port | ||||
| CcienaCesBenchmarkEntityStatsEntryPortRxUndersizePkts | 1.3.6.1.4.1.1271.2.1.39.1.1.3.1.8 | Counter64 | RO | |
column · Counter64 · read-only · current The total number of packets received that were less than 64 octets long (excluding framing bits, but including FCS octets) and were otherwise well formed. | ||||
| CcienaCesBenchmarkEntityStatsEntryPortRxOversizePkts | 1.3.6.1.4.1.1271.2.1.39.1.1.3.1.9 | Counter64 | RO | |
column · Counter64 · read-only · current The total number of packets received that were longer than 1518 octets (excluding framing bits, but including FCS octets) and were otherwise well formed. | ||||
| CcienaCesBenchmarkEntityStatsEntryPortRxFragmentsPkts | 1.3.6.1.4.1.1271.2.1.39.1.1.3.1.10 | Counter64 | RO | |
column · Counter64 · read-only · current The total number of packets received that were less than 64 octets in length (excluding framing bits but including FCS octets) and had either a bad Frame Check Sequence (FCS) with an integral number of octets (FCS Error) or a bad FCS with a non-integral number of octets (Alignment Error). | ||||
| CcienaCesBenchmarkEntityStatsEntryPortRxJabbersPkts | 1.3.6.1.4.1.1271.2.1.39.1.1.3.1.11 | Counter64 | RO | |
column · Counter64 · read-only · current The total number of packets received that were longer than 1518 octets (excluding framing bits, but including FCS octets), and had either a bad Frame Check Sequence (FCS) with an integral number of octets (FCS Error) or a bad FCS with a non-integral number of octets (Alignment Error). | ||||
| CcienaCesBenchmarkEntityStatsEntryPortTxPausePkts | 1.3.6.1.4.1.1271.2.1.39.1.1.3.1.12 | Counter64 | RO | |
column · Counter64 · read-only · current The transmit pause packets for the port. | ||||
| CcienaCesBenchmarkEntityStatsEntryPortTxDropPkts | 1.3.6.1.4.1.1271.2.1.39.1.1.3.1.13 | Counter64 | RO | |
column · Counter64 · read-only · current The total number of dropped packets on the benchmark port when traffic profiles are enabled (311v only). | ||||
| CcienaCesBenchmarkEntityStatsEntryPortTxDiscardPkts | 1.3.6.1.4.1.1271.2.1.39.1.1.3.1.14 | Counter64 | RO | |
column · Counter64 · read-only · current The total number of discarded packets. | ||||
| CcienaCesBenchmarkEntityStatsEntryPortTxLOutRangePkts | 1.3.6.1.4.1.1271.2.1.39.1.1.3.1.15 | Counter64 | RO | |
column · Counter64 · read-only · current The transmit length out of range packet count. | ||||
| CcienaCesBenchmarkEntityStatsEntryPortTx64OctsPkts | 1.3.6.1.4.1.1271.2.1.39.1.1.3.1.16 | Counter64 | RO | |
column · Counter64 · read-only · current Number of 64-byte packets transmitted on the benchmark port. | ||||
| CcienaCesBenchmarkEntityStatsEntryPortTx65To127Pkts | 1.3.6.1.4.1.1271.2.1.39.1.1.3.1.17 | Counter64 | RO | |
column · Counter64 · read-only · current Number of 64 to 127-byte packets transmitted on the benchmark port. | ||||
| CcienaCesBenchmarkEntityStatsEntryPortTx128To255Pkts | 1.3.6.1.4.1.1271.2.1.39.1.1.3.1.18 | Counter64 | RO | |
column · Counter64 · read-only · current Number of 128 to 255-byte packets transmitted on the benchmark port. | ||||
| CcienaCesBenchmarkEntityStatsEntryPortTx256To511Pkts | 1.3.6.1.4.1.1271.2.1.39.1.1.3.1.19 | Counter64 | RO | |
column · Counter64 · read-only · current Number of 256 to 511-byte packets transmitted on the benchmark port. | ||||
| CcienaCesBenchmarkEntityStatsEntryPortTx512To1023Pkts | 1.3.6.1.4.1.1271.2.1.39.1.1.3.1.20 | Counter64 | RO | |
column · Counter64 · read-only · current Number of 512 to 1023-byte packets transmitted on the benchmark port. | ||||
| CcienaCesBenchmarkEntityStatsEntryPortTx1024To1518Pkts | 1.3.6.1.4.1.1271.2.1.39.1.1.3.1.21 | Counter64 | RO | |
column · Counter64 · read-only · current Number of 1024 to 1518-byte packets transmitted on the benchmark port. | ||||
| CcienaCesBenchmarkEntityStatsEntryPortTx1519To2047Pkts | 1.3.6.1.4.1.1271.2.1.39.1.1.3.1.22 | Counter64 | RO | |
column · Counter64 · read-only · current Number of 1519 to 2047-byte packets transmitted on the benchmark port. | ||||
| CcienaCesBenchmarkEntityStatsEntryPortTx2048To4095Pkts | 1.3.6.1.4.1.1271.2.1.39.1.1.3.1.23 | Counter64 | RO | |
column · Counter64 · read-only · current Number of 2048 to 4095-byte packets transmitted on the benchmark port. | ||||
| CcienaCesBenchmarkEntityStatsEntryPortTx4096To9216Pkts | 1.3.6.1.4.1.1271.2.1.39.1.1.3.1.24 | Counter64 | RO | |
column · Counter64 · read-only · current Number of 4096 to 9216-byte packets transmitted on the benchmark port. | ||||
| CcienaCesBenchmarkEntityStatsEntryPortRxBytes | 1.3.6.1.4.1.1271.2.1.39.1.1.3.1.25 | Counter64 | RO | |
column · Counter64 · read-only · current Number of bytes received on the benchmark port. | ||||
| CcienaCesBenchmarkEntityStatsEntryPortRxPkts | 1.3.6.1.4.1.1271.2.1.39.1.1.3.1.26 | Counter64 | RO | |
column · Counter64 · read-only · current Number of packets received on the benchmark port. | ||||
| CcienaCesBenchmarkEntityStatsEntryPortRxExDeferPkts | 1.3.6.1.4.1.1271.2.1.39.1.1.3.1.27 | Counter64 | RO | |
column · Counter64 · read-only · current Number of excessive deferred packets. | ||||
| CcienaCesBenchmarkEntityStatsEntryPortRxDeferPkts | 1.3.6.1.4.1.1271.2.1.39.1.1.3.1.28 | Counter64 | RO | |
column · Counter64 · read-only · current Number of deferred packets. | ||||
| CcienaCesBenchmarkEntityStatsEntryPortRxGiantPkts | 1.3.6.1.4.1.1271.2.1.39.1.1.3.1.29 | Counter64 | RO | |
column · Counter64 · read-only · current Number of too big packets. | ||||
| CcienaCesBenchmarkEntityStatsEntryPortRxUnderRunPkts | 1.3.6.1.4.1.1271.2.1.39.1.1.3.1.30 | Counter64 | RO | |
column · Counter64 · read-only · current Underrun packet count for the benchmark port. | ||||
| CcienaCesBenchmarkEntityStatsEntryPortRxCrcErrorPkts | 1.3.6.1.4.1.1271.2.1.39.1.1.3.1.31 | Counter64 | RO | |
column · Counter64 · read-only · current Number of packets received with CRC errors. | ||||
| CcienaCesBenchmarkEntityStatsEntryPortRxLCheckErrorPkts | 1.3.6.1.4.1.1271.2.1.39.1.1.3.1.32 | Counter64 | RO | |
column · Counter64 · read-only · current Number of packets with length check errors. | ||||
| CcienaCesBenchmarkEntityStatsEntryPortRxLOutRangePkts | 1.3.6.1.4.1.1271.2.1.39.1.1.3.1.33 | Counter64 | RO | |
column · Counter64 · read-only · current The number of frames received by the benchmark port that exceeded the maximum permitted frame size. | ||||
| CcienaCesBenchmarkEntityStatsEntryPortRxPausePkts | 1.3.6.1.4.1.1271.2.1.39.1.1.3.1.34 | Counter64 | RO | |
column · Counter64 · read-only · current The total receive pause packets for the port. | ||||
| CcienaCesBenchmarkEntityStatsEntryPortRxUcastPkts | 1.3.6.1.4.1.1271.2.1.39.1.1.3.1.35 | Counter64 | RO | |
column · Counter64 · read-only · current The total number of unicast packets received by benchmark port. | ||||
| CcienaCesBenchmarkEntityStatsEntryPortRxMcastPkts | 1.3.6.1.4.1.1271.2.1.39.1.1.3.1.36 | Counter64 | RO | |
column · Counter64 · read-only · current The total number of multicast packets received by benchmark port. | ||||
| CcienaCesBenchmarkEntityStatsEntryPortRxBcastPkts | 1.3.6.1.4.1.1271.2.1.39.1.1.3.1.37 | Counter64 | RO | |
column · Counter64 · read-only · current The total number of broadcast packets received by benchmark port. | ||||
| CcienaCesBenchmarkEntityStatsEntryPortRx64OctsPkts | 1.3.6.1.4.1.1271.2.1.39.1.1.3.1.38 | Counter64 | RO | |
column · Counter64 · read-only · current The total number of 64-byte packets received by benchmark port. | ||||
| CcienaCesBenchmarkEntityStatsEntryPortRx65To127Pkts | 1.3.6.1.4.1.1271.2.1.39.1.1.3.1.39 | Counter64 | RO | |
column · Counter64 · read-only · current The total number of 65 to 127-byte packets received by benchmark port. | ||||
| CcienaCesBenchmarkEntityStatsEntryPortRx128To255Pkts | 1.3.6.1.4.1.1271.2.1.39.1.1.3.1.40 | Counter64 | RO | |
column · Counter64 · read-only · current The total number of 128 to 255-byte packets received by benchmark port. | ||||
| CcienaCesBenchmarkEntityStatsEntryPortRx256To511Pkts | 1.3.6.1.4.1.1271.2.1.39.1.1.3.1.41 | Counter64 | RO | |
column · Counter64 · read-only · current The total number of 256 to 511-byte packets received by benchmark port. | ||||
| CcienaCesBenchmarkEntityStatsEntryPortRx512To1023Pkts | 1.3.6.1.4.1.1271.2.1.39.1.1.3.1.42 | Counter64 | RO | |
column · Counter64 · read-only · current The total number of 512 to 1023-byte packets received by benchmark port. | ||||
| CcienaCesBenchmarkEntityStatsEntryPortRx1024To1518Pkts | 1.3.6.1.4.1.1271.2.1.39.1.1.3.1.43 | Counter64 | RO | |
column · Counter64 · read-only · current The total number of 1024 to 1518-byte packets received by benchmark port. | ||||
| CcienaCesBenchmarkEntityStatsEntryPortRx1519To2047Pkts | 1.3.6.1.4.1.1271.2.1.39.1.1.3.1.44 | Counter64 | RO | |
column · Counter64 · read-only · current The total number of 1519 to 2047-byte packets received by benchmark port. | ||||
| CcienaCesBenchmarkEntityStatsEntryPortRx2048To4095Pkts | 1.3.6.1.4.1.1271.2.1.39.1.1.3.1.45 | Counter64 | RO | |
column · Counter64 · read-only · current The total number of 2048 to 4095-byte packets received by benchmark port. | ||||
| CcienaCesBenchmarkEntityStatsEntryPortRx4096To9216Pkts | 1.3.6.1.4.1.1271.2.1.39.1.1.3.1.46 | Counter64 | RO | |
column · Counter64 · read-only · current The total number of 4096 to 9216-byte packets received by benchmark port. | ||||
| CcienaCesBenchmarkEntityStatsEntryFpgaMissClassPkts | 1.3.6.1.4.1.1271.2.1.39.1.1.3.1.47 | Counter64 | RO | |
column · Counter64 · read-only · current Test packets received that didn't match any enabled test session. | ||||
| CcienaCesBenchmarkEntityStatsEntryFpgaCrcErrPkts | 1.3.6.1.4.1.1271.2.1.39.1.1.3.1.48 | Counter64 | RO | |
column · Counter64 · read-only · current Test packets received with CRC errors | ||||
| CcienaCesBenchmarkEntityStatsEntryFpgaUdpChkSumErrPkts | 1.3.6.1.4.1.1271.2.1.39.1.1.3.1.49 | Counter64 | RO | |
column · Counter64 · read-only · current Test packets received with UDP checksum errors | ||||
| TcienaCesBenchmarkEmixSequenceTable | 1.3.6.1.4.1.1271.2.1.39.1.1.4 | NA | ||
table · not-accessible · current Table providing the list of configured EMIX sequences on this node. | ||||
| RcienaCesBenchmarkEmixSequenceEntry | 1.3.6.1.4.1.1271.2.1.39.1.1.4.1 | NA | ||
| CcienaCesBenchmarkEmixSequenceId | 1.3.6.1.4.1.1271.2.1.39.1.1.4.1.1 | Integer32 (1..32) | NA | |
column · Integer32 (1..32) · not-accessible · current Unique Id of the EMIX sequence entry | ||||
| CcienaCesBenchmarkEmixSequenceName | 1.3.6.1.4.1.1271.2.1.39.1.1.4.1.2 | DisplayString (SIZE (1..46)) | RC | |
column · DisplayString (SIZE (1..46)) · read-create · current Name of this EMIX sequence | ||||
| CcienaCesBenchmarkEmixSequence | 1.3.6.1.4.1.1271.2.1.39.1.1.4.1.3 | DisplayString (SIZE (1..16)) | RC | |
column · DisplayString (SIZE (1..16)) · read-create · current EMIX sequence which is a sequence of up to
16 letters from the following set, that can
be repeated, where each letter is associated with
the frame size below it:
a b c d e f g h u v w x
64 128 256 512 1024 1280 1518 MTU custom 84 68 88
The u frame size is user configurable via the
cienaCesBenchmarkEmixSequenceUFrameSize attribute
while the h frame size is the maximum frame size
configured at the entity level. If the h frame size is
not configured at the entity level, h takes the value of
the maximum frame size of the port under test.
Letter v is the minimum frame size for IPv6 untagged or dot1q
test frames, w is the minimum for IPv4 qinq test frames, and
x is the minimum for IPv6 qinq test frames.
The EMIX character set is available via table
cienaCesBenchmarkEmixCharacterSetTable. | ||||
| CcienaCesBenchmarkEmixSequenceUFrameSize | 1.3.6.1.4.1.1271.2.1.39.1.1.4.1.4 | Integer32 (64..9216) | RC | |
column · Integer32 (64..9216) · read-create · current The frame size associated with the u letter in the given sequence. The default value is 594. | ||||
| CcienaCesBenchmarkEmixSequenceNumOfRef | 1.3.6.1.4.1.1271.2.1.39.1.1.4.1.5 | Integer32 | RO | |
column · Integer32 · read-only · current Number of generator test profiles currently using this EMIX sequence for testing. If this is the default EMIX sequence set in the generator, that also count as one reference. | ||||
| CcienaCesBenchmarkEmixSequenceUserCreated | 1.3.6.1.4.1.1271.2.1.39.1.1.4.1.6 | TruthValue | RO | |
column · TruthValue · read-only · current Flag indicating whether this sequence was created by the user or by the system at initialization. Only user created sequences are editable. | ||||
| CcienaCesBenchmarkEmixSequenceRowStatus | 1.3.6.1.4.1.1271.2.1.39.1.1.4.1.7 | RowStatus | RC | |
column · RowStatus · read-create · current Used to manage the creation and deletion of the conceptual rows in this table. To create a row in this table, set this object to 'createAndGo'. To delete a row in this table, set this object to 'destroy'. If the entry exists, it is displayed as 'active'. | ||||
| TcienaCesBenchmarkEmixFrameSizeTable | 1.3.6.1.4.1.1271.2.1.39.1.1.5 | NA | ||
table · not-accessible · current Table providing the list of frame sizes associated with the specified EMIX sequence Id. | ||||
| RcienaCesBenchmarkEmixFrameSizeEntry | 1.3.6.1.4.1.1271.2.1.39.1.1.5.1 | NA | ||
row · not-accessible · current Frame size associated with given EMIX sequence ID and frame size index on a given Entity | ||||
| CcienaCesBenchmarkEmixFrameSizeIndex | 1.3.6.1.4.1.1271.2.1.39.1.1.5.1.1 | Integer32 (1..16) | NA | |
column · Integer32 (1..16) · not-accessible · current Index of frame size in array of frame sizes for the given EMIX sequence. | ||||
| CcienaCesBenchmarkEmixFrameSizeEntryFrameSize | 1.3.6.1.4.1.1271.2.1.39.1.1.5.1.2 | Integer32 (64..9216) | RO | |
column · Integer32 (64..9216) · read-only · current Frame size associated with the letter at the position given by cienaCesBenchmarkEmixFrameSizeIndex in the EMIX sequence with Id cienaCesBenchmarkEmixSequenceId. | ||||
| TcienaCesBenchmarkEmixAvgFrameSizeTable | 1.3.6.1.4.1.1271.2.1.39.1.1.6 | NA | ||
table · not-accessible · current Table providing the average frame size associated with the specified EMIX sequence Id on a given Entity. | ||||
| RcienaCesBenchmarkEmixAvgFrameSizeEntry | 1.3.6.1.4.1.1271.2.1.39.1.1.6.1 | NA | ||
row · not-accessible · current Average frame size associated with given EMIX sequence ID and Entity. Only valid for Generator entities. | ||||
| CcienaCesBenchmarkEmixAvgFrameSize | 1.3.6.1.4.1.1271.2.1.39.1.1.6.1.1 | Integer32 (64..9216) | RO | |
column · Integer32 (64..9216) · read-only · current Average frame size for the EMIX sequence with Id cienaCesBenchmarkEmixSequenceId on the generator entity with Id cienaCesBenchmarkEntityEntryId. | ||||
| TcienaCesBenchmarkKpiProfileTable | 1.3.6.1.4.1.1271.2.1.39.1.1.7 | NA | ||
table · not-accessible · current Table providing the list of configured Key Performance Indicator profiles on this node. | ||||
| RcienaCesBenchmarkKpiProfileEntry | 1.3.6.1.4.1.1271.2.1.39.1.1.7.1 | NA | ||
| CcienaCesBenchmarkKpiProfileId | 1.3.6.1.4.1.1271.2.1.39.1.1.7.1.1 | Integer32 (1..32) | NA | |
column · Integer32 (1..32) · not-accessible · current Unique Id of the KPI profile entry | ||||
| CcienaCesBenchmarkKpiProfileName | 1.3.6.1.4.1.1271.2.1.39.1.1.7.1.2 | DisplayString (SIZE (1..46)) | RC | |
column · DisplayString (SIZE (1..46)) · read-create · current Name of a the KPI profile | ||||
| CcienaCesBenchmarkKpiProfileNumOfRef | 1.3.6.1.4.1.1271.2.1.39.1.1.7.1.3 | Integer32 | RO | |
column · Integer32 · read-only · current Number of generator test profiles currently using this KPI profile for results analysis. If this is the default KPI profile set in the generator, that also count as one reference. | ||||
| CcienaCesBenchmarkKpiProfileRowStatus | 1.3.6.1.4.1.1271.2.1.39.1.1.7.1.4 | RowStatus | RC | |
column · RowStatus · read-create · current Used to manage the creation and deletion of the conceptual rows in this table. To create a row in this table, set this object to 'createAndGo'. To delete a row in this table, set this object to 'destroy'. If the entry exists, it is displayed as 'active'. | ||||
| TcienaCesBenchmarkKpiPcpColorTable | 1.3.6.1.4.1.1271.2.1.39.1.1.8 | NA | ||
table · not-accessible · current Table providing the list of configured Key Performance Indicator per KPI profile, per PCP and per Color. | ||||
| RcienaCesBenchmarkKpiPcpColorEntry | 1.3.6.1.4.1.1271.2.1.39.1.1.8.1 | NA | ||
row · not-accessible · current Entry for the KPI values for the given KPI profile, PCP and color. | ||||
| CcienaCesBenchmarkKpiPcpIndex | 1.3.6.1.4.1.1271.2.1.39.1.1.8.1.1 | Integer32 (1..8) | NA | |
column · Integer32 (1..8) · not-accessible · current Index for the PCP | ||||
| CcienaCesBenchmarkKpiColorIndex | 1.3.6.1.4.1.1271.2.1.39.1.1.8.1.2 | Integer32 (1..2) | NA | |
column · Integer32 (1..2) · not-accessible · current Index for the PCP | ||||
| CcienaCesBenchmarkKpiPcp | 1.3.6.1.4.1.1271.2.1.39.1.1.8.1.3 | Integer32 (0..7) | RO | |
column · Integer32 (0..7) · read-only · current PCP value associated with this entry | ||||
| CcienaCesBenchmarkKpiColor | 1.3.6.1.4.1.1271.2.1.39.1.1.8.1.4 | CienaCesBenchmarkColorTest | RO | |
column · CienaCesBenchmarkColorTest · read-only · current Traffic color, green or yellow, associated with these KPIs. | ||||
| CcienaCesBenchmarkKpiThroughput | 1.3.6.1.4.1.1271.2.1.39.1.1.8.1.5 | CienaCesBenchmarkThroughputKpiPercent | RW | |
column · CienaCesBenchmarkThroughputKpiPercent · read-write · current Throughput KPI for the given KPI profile, PCP and color expressed in percent of bandwidth * 10000 to provide a 4 decimal point value. | ||||
| CcienaCesBenchmarkKpiFrameloss | 1.3.6.1.4.1.1271.2.1.39.1.1.8.1.6 | CienaCesBenchmarkFramelossKpiPercent | RW | |
column · CienaCesBenchmarkFramelossKpiPercent · read-write · current Frameloss KPI for the given KPI profile, PCP and color expressed in percent of bandwidth * 10000 to provide a 4 decimal point value. | ||||
| CcienaCesBenchmarkKpiLatency | 1.3.6.1.4.1.1271.2.1.39.1.1.8.1.7 | Integer32 | RW | |
column · Integer32 · read-write · current Maximum latency in micro-seconds that the latency result should not exceed in order for the test to be considered a pass.
| ||||
| CcienaCesBenchmarkKpiPdv | 1.3.6.1.4.1.1271.2.1.39.1.1.8.1.8 | Integer32 | RW | |
column · Integer32 · read-write · current Maximum PDV in micro-seconds that the PDV test result should not exceed in order for the test to be considered a pass.
| ||||
| TcienaCesBenchmarkBwAllocProfileTable | 1.3.6.1.4.1.1271.2.1.39.1.1.9 | NA | ||
table · not-accessible · current Table providing the list of configured bandwidth allocation profiles on this node. | ||||
| RcienaCesBenchmarkBwAllocProfileEntry | 1.3.6.1.4.1.1271.2.1.39.1.1.9.1 | NA | ||
| CcienaCesBenchmarkBwAllocProfileId | 1.3.6.1.4.1.1271.2.1.39.1.1.9.1.1 | Integer32 (1..32) | NA | |
column · Integer32 (1..32) · not-accessible · current Unique Id of the bandwidth allocation profile entry | ||||
| CcienaCesBenchmarkBwAllocProfileName | 1.3.6.1.4.1.1271.2.1.39.1.1.9.1.2 | DisplayString (SIZE (1..46)) | RC | |
column · DisplayString (SIZE (1..46)) · read-create · current Name of a the bandwidth allocation profile | ||||
| CcienaCesBenchmarkBwAllocProfileNumOfRef | 1.3.6.1.4.1.1271.2.1.39.1.1.9.1.3 | Integer32 | RO | |
column · Integer32 · read-only · current Number of generator test profiles currently using this bandwidth allocation profile for testing. If this is the default BW allocation profile set in the generator, that also count as one reference. | ||||
| CcienaCesBenchmarkBwAllocProfileRowStatus | 1.3.6.1.4.1.1271.2.1.39.1.1.9.1.4 | RowStatus | RC | |
column · RowStatus · read-create · current Used to manage the creation and deletion of the conceptual rows in this table. To create a row in this table, set this object to 'createAndGo'. To delete a row in this table, set this object to 'destroy'. If the entry exists, it is displayed as 'active'. | ||||
| TcienaCesBenchmarkBwRatioTable | 1.3.6.1.4.1.1271.2.1.39.1.1.10 | NA | ||
table · not-accessible · current Table providing the list of configured bandwidth ratio per profile, per PCP. | ||||
| RcienaCesBenchmarkBwRatioEntry | 1.3.6.1.4.1.1271.2.1.39.1.1.10.1 | NA | ||
row · not-accessible · current Entry for bandwidth percent per BW Allocation profile and PCP | ||||
| CcienaCesBenchmarkBwRatioPcpIndex | 1.3.6.1.4.1.1271.2.1.39.1.1.10.1.1 | Integer32 (1..8) | NA | |
column · Integer32 (1..8) · not-accessible · current Index for the PCP | ||||
| CcienaCesBenchmarkBwRatioPcp | 1.3.6.1.4.1.1271.2.1.39.1.1.10.1.2 | Integer32 (0..7) | RO | |
column · Integer32 (0..7) · read-only · current PCP value associated with this entry. | ||||
| CcienaCesBenchmarkBwRatio | 1.3.6.1.4.1.1271.2.1.39.1.1.10.1.3 | Integer32 (0..1000000) | RW | |
column · Integer32 (0..1000000) · read-write · current Ratio of test bandwidth to allocate to the test session with this PCP value. | ||||
| TcienaCesBenchmarkProfileTable | 1.3.6.1.4.1.1271.2.1.39.1.1.11 | NA | ||
table · not-accessible · current Table of profile entries. | ||||
| RcienaCesBenchmarkProfileEntry | 1.3.6.1.4.1.1271.2.1.39.1.1.11.1 | NA | ||
row · not-accessible · current BENCHMARK Profile characteristics. | ||||
| CcienaCesBenchmarkProfileEntryId | 1.3.6.1.4.1.1271.2.1.39.1.1.11.1.1 | Integer32 | NA | |
column · Integer32 · not-accessible · current Index for BENCHMARK profile records. | ||||
| CcienaCesBenchmarkProfileEntryName | 1.3.6.1.4.1.1271.2.1.39.1.1.11.1.2 | DisplayString (SIZE (1..46)) | RC | |
column · DisplayString (SIZE (1..46)) · read-create · current Name of the profile as entered when created. | ||||
| CcienaCesBenchmarkProfileEntryBandwidth | 1.3.6.1.4.1.1271.2.1.39.1.1.11.1.3 | Integer32 (1..10000) | RC | |
column · Integer32 (1..10000) · read-create · current Maximum bandwidth to use when generating green test traffic for the profile. | ||||
| CcienaCesBenchmarkProfileEntryExcessBandwidth | 1.3.6.1.4.1.1271.2.1.39.1.1.11.1.4 | Integer32 (0..10000) | RC | |
column · Integer32 (0..10000) · read-create · current Maximum bandwidth to use when generating yellow test traffic for the profile. When testing for red color, this bandwidth is multiplied by 1.25 | ||||
| CcienaCesBenchmarkProfileEntryInterval | 1.3.6.1.4.1.1271.2.1.39.1.1.11.1.5 | INTEGER | RC | |
column · INTEGER · read-create · current Interval between the start of one test group to the start of the next test group.
| ||||
| CcienaCesBenchmarkProfileEntryDuration | 1.3.6.1.4.1.1271.2.1.39.1.1.11.1.6 | INTEGER | RC | |
column · INTEGER · read-create · current Duration of the testing. The test group is repeated until the duration ends. When indefinite is set, test group is run only once to completion
| ||||
| CcienaCesBenchmarkProfileEntrySetFrameSizeList | 1.3.6.1.4.1.1271.2.1.39.1.1.11.1.7 | DisplayString (SIZE (0..255)) | RC | |
column · DisplayString (SIZE (0..255)) · read-create · current Used to replace the existing frame size table with the specified list. More than one values can be listed and are separated by commas. | ||||
| CcienaCesBenchmarkProfileEntryMaxSearches | 1.3.6.1.4.1.1271.2.1.39.1.1.11.1.8 | Integer32 (1..16) | RC | |
column · Integer32 (1..16) · read-create · current For the throughput test, this is the maximum number of searches to find a transmit rate without drops for a given frame size. | ||||
| CcienaCesBenchmarkProfileEntryMaxSamples | 1.3.6.1.4.1.1271.2.1.39.1.1.11.1.9 | Integer32 (2..20) | RC | |
column · Integer32 (2..20) · read-create · current For the latency and PDV tests, this is the number of samples to take in order to determine the min, avg and max latency and avg PDV. | ||||
| CcienaCesBenchmarkProfileEntrySamplingInterval | 1.3.6.1.4.1.1271.2.1.39.1.1.11.1.10 | Integer32 (1..600) | RC | |
column · Integer32 (1..600) · read-create · current For the latency and PDV tests, this is the interval, in 100ms, to wait between samples. | ||||
| CcienaCesBenchmarkProfileEntryFrameLossStartBw | 1.3.6.1.4.1.1271.2.1.39.1.1.11.1.11 | INTEGER | RC | |
column · INTEGER · read-create · current For the frame loss test, this indicates which bandwidth value to use as the starting bandwidth; the maximum bandwidth determined via the throughput test, the bandwidth parameter configured in the profile, or the maximum bandwidth of the link. The value maximumLineRate(3) is not supported.
| ||||
| CcienaCesBenchmarkProfileEntryVidValidation | 1.3.6.1.4.1.1271.2.1.39.1.1.11.1.12 | TruthValue | RC | |
column · TruthValue · read-create · current Indicates whether VID validation is performed in the classifier or not on the returning packet. If vid validation is set to false, PCP and Color validation are ignored and automatically become false. | ||||
| CcienaCesBenchmarkProfileEntryPcpValidation | 1.3.6.1.4.1.1271.2.1.39.1.1.11.1.13 | TruthValue | RC | |
column · TruthValue · read-create · current Used to indicate whether the PCP value of the test packet should be used to classifier the reflected packets or not. When color remarking is used, this should be set to false. Default is true. | ||||
| CcienaCesBenchmarkProfileEntryColorValidation | 1.3.6.1.4.1.1271.2.1.39.1.1.11.1.14 | TruthValue | RC | |
column · TruthValue · read-create · current Used to indicate whether the color bit of the test packet should be used to classifier the reflected packets or not. In color unaware testing, this should be set to false. Default is true. | ||||
| CcienaCesBenchmarkProfileEntryKpiProfileId | 1.3.6.1.4.1.1271.2.1.39.1.1.11.1.15 | Integer32 (0..32) | RC | |
column · Integer32 (0..32) · read-create · current Name of a valid KPI profile, from the cienaCesBenchmarkKpiProfileTable, to use when analysing the test results for this profile. | ||||
| CcienaCesBenchmarkProfileEntryBwAllocProfileId | 1.3.6.1.4.1.1271.2.1.39.1.1.11.1.16 | Integer32 (0..32) | RC | |
column · Integer32 (0..32) · read-create · current Id of a valid Bandwidth Allocation profile, from the cienaCesBenchmarkBwAllocProfileTable, used for distributing the profile bandwidth amongst the configured PCP values for this profile when running tests. | ||||
| CcienaCesBenchmarkProfileEntryEmixSequenceId | 1.3.6.1.4.1.1271.2.1.39.1.1.11.1.17 | Integer32 (0..32) | RC | |
column · Integer32 (0..32) · read-create · current Id of a valid EMIX sequence configured in the cienaCesBenchmarkEmixSequenceTable, to use when y1564 is selected. The EMIX sequence is used instead of the frame size list if and only if y1564 is selected. | ||||
| CcienaCesBenchmarkProfileEntryEncapType | 1.3.6.1.4.1.1271.2.1.39.1.1.11.1.18 | INTEGER | RC | |
column · INTEGER · read-create · current Encapsulation type to use for generated packets.
| ||||
| CcienaCesBenchmarkProfileEntryPduType | 1.3.6.1.4.1.1271.2.1.39.1.1.11.1.19 | INTEGER | RC | |
column · INTEGER · read-create · current Vlan tag protocol identifier to use for the generated packets.
| ||||
| CcienaCesBenchmarkProfileEntryDstmac | 1.3.6.1.4.1.1271.2.1.39.1.1.11.1.20 | MacAddress | RC | |
column · MacAddress · read-create · current MAC address to use as the destination MAC address on the generated packets. | ||||
| CcienaCesBenchmarkProfileEntrySVid | 1.3.6.1.4.1.1271.2.1.39.1.1.11.1.21 | Integer32 (0..4094) | RC | |
column · Integer32 (0..4094) · read-create · current S-VLAN ID to used for generated packets when encapType is set to QinQ | ||||
| CcienaCesBenchmarkProfileEntrySPcp | 1.3.6.1.4.1.1271.2.1.39.1.1.11.1.22 | CienaCesBenchmarkPcpBitmap | RC | |
column · CienaCesBenchmarkPcpBitmap · read-create · current Bitmap of the S-VLAN PCP (Priority Code Point) value to test with. When RFC2544 test is enabled, only one PCP can be set in the mask. Otherwise, a test session will be run for each PCP bit set. Used when the encapType set to QinQ | ||||
| CcienaCesBenchmarkProfileEntrySColor | 1.3.6.1.4.1.1271.2.1.39.1.1.11.1.23 | CienaCesBenchmarkColorTest | RC | |
column · CienaCesBenchmarkColorTest · read-create · current Color of the S-VLAN tag for the test traffic. This is directly related to the value of the DEI bit configured in the VLAN tag of the test traffic. Green traffic will have its DEI bit set to 0 while Yellow traffic will have its DEI bit set to 1. Green test traffic is generated based on the bandwidth configured in the test profile. Yellow traffic is generated based on the excess-bandwidth parameter. Finally, if the user selects green-yellow-red, the yellow traffic is generated at 1.25 * excess-bandwidth. This is used only when encapType is set to QinQ | ||||
| CcienaCesBenchmarkProfileEntryCVid | 1.3.6.1.4.1.1271.2.1.39.1.1.11.1.24 | Integer32 (0..4094) | RC | |
column · Integer32 (0..4094) · read-create · current C-VLAN ID to used for generated packets when encapType is set to QinQ or dot1q. | ||||
| CcienaCesBenchmarkProfileEntryCPcp | 1.3.6.1.4.1.1271.2.1.39.1.1.11.1.25 | CienaCesBenchmarkPcpBitmap | RC | |
column · CienaCesBenchmarkPcpBitmap · read-create · current Bitmap of the C-VLAN PCP (Priority Code Point) value to test with. When RFC2544 test is enabled, only one PCP can be set in the mask. Otherwise, a test session will be run for each PCP bit set. Only used when the encapType is set to dot1q. In the QinQ type, the c-pcp of the test packet takes the same value as the s-pcp to simplify software. | ||||
| CcienaCesBenchmarkProfileEntryCColor | 1.3.6.1.4.1.1271.2.1.39.1.1.11.1.26 | CienaCesBenchmarkColorTest | RC | |
column · CienaCesBenchmarkColorTest · read-create · current Color of the C-VLAN tag for the test traffic. This is directly related to the value of the DEI bit configured in the VLAN tag of the test traffic. Green traffic will have its DEI bit set to 0 while Yellow traffic will have its DEI bit set to 1. Green test traffic is generated based on the bandwidth configured in the test profile. Yellow traffic is generated based on the excess-bandwidth parameter. Finally, if the user selects green-yellow-red, the yellow traffic is generated at 1.25 * excess-bandwidth. This is used only when encapType is set to dot1q. In a QinQ configuration, the c-dei bit is set to the same value as the s-dei bit in order to simplify software. | ||||
| CcienaCesBenchmarkProfileEntryTpid | 1.3.6.1.4.1.1271.2.1.39.1.1.11.1.27 | Integer32 (0..65535) | RC | |
column · Integer32 (0..65535) · read-create · current Vlan tag protocol identifier to use for the generated packets.
The following TPID values are supported by benchmark:
0x8100
0x9100
0x88A8 | ||||
| CcienaCesBenchmarkProfileEntryDscp | 1.3.6.1.4.1.1271.2.1.39.1.1.11.1.28 | Integer32 (0..63) | RC | |
column · Integer32 (0..63) · read-create · current IP DSCP value to use for the generated packets. | ||||
| CcienaCesBenchmarkProfileEntrySrcInetAddrType | 1.3.6.1.4.1.1271.2.1.39.1.1.11.1.29 | InetAddressType | RC | |
column · InetAddressType · read-create · current Specifies the type of address cienaCesBenchmarkProfileEntrySrcInetAddr belongs to.
When set to:
ipv4 : cienaCesBenchmarkProfileEntrySrcInetAddr should be compliant with
InetAddressIPv4 from RFC 4001
ipv6 : cienaCesBenchmarkProfileEntrySrcInetAddr should be compliant with
InetAddressIPv6 from RFC 4001.
The InetAddressType and the InetAddress must be set as part of the same SNMP
SET request. | ||||
| CcienaCesBenchmarkProfileEntrySrcInetAddr | 1.3.6.1.4.1.1271.2.1.39.1.1.11.1.30 | InetAddress | RC | |
column · InetAddress · read-create · current Specifies the unicast source IP address to use in IP test packet. The InetAddress specified here is compliant with RFC 4001. The InetAddressType and the InetAddress must be set as part of the same SNMP SET request. | ||||
| CcienaCesBenchmarkProfileEntryDstInetAddrType | 1.3.6.1.4.1.1271.2.1.39.1.1.11.1.31 | InetAddressType | RC | |
column · InetAddressType · read-create · current Specifies the type of address cienaCesBenchmarkProfileEntryDstInetAddr belongs to.
When set to:
ipv4 : cienaCesBenchmarkProfileEntryDstInetAddr should be compliant with
InetAddressIPv4 from RFC 4001
ipv6 : cienaCesBenchmarkProfileEntryDstInetAddr should be compliant with
InetAddressIPv6 from RFC 4001.
The InetAddressType and the InetAddress must be set as part of the same SNMP
SET request. | ||||
| CcienaCesBenchmarkProfileEntryDstInetAddr | 1.3.6.1.4.1.1271.2.1.39.1.1.11.1.32 | InetAddress | RC | |
column · InetAddress · read-create · current Specifies the unicast destination IP address to use in IP test packet. The InetAddress specified here is compliant with RFC 4001. The InetAddressType and the InetAddress must be set as part of the same SNMP SET request. | ||||
| CcienaCesBenchmarkProfileEntryCustomPayload | 1.3.6.1.4.1.1271.2.1.39.1.1.11.1.33 | OCTET STRING (SIZE (0..256)) | RC | |
column · OCTET STRING (SIZE (0..256)) · read-create · current Custom payload to be used on the generated packets. | ||||
| CcienaCesBenchmarkProfileEntryThroughputTest | 1.3.6.1.4.1.1271.2.1.39.1.1.11.1.34 | TruthValue | RC | |
column · TruthValue · read-create · current Run throughput test | ||||
| CcienaCesBenchmarkProfileEntryFramelossTest | 1.3.6.1.4.1.1271.2.1.39.1.1.11.1.35 | TruthValue | RC | |
column · TruthValue · read-create · current Run frame loss test | ||||
| CcienaCesBenchmarkProfileEntryLatencyTest | 1.3.6.1.4.1.1271.2.1.39.1.1.11.1.36 | TruthValue | RC | |
column · TruthValue · read-create · current Run latency test | ||||
| CcienaCesBenchmarkProfileEntryPdvTest | 1.3.6.1.4.1.1271.2.1.39.1.1.11.1.37 | TruthValue | RC | |
column · TruthValue · read-create · current Run packet delay variation test | ||||
| CcienaCesBenchmarkProfileEntryBurstTest | 1.3.6.1.4.1.1271.2.1.39.1.1.11.1.38 | TruthValue | RC | |
column · TruthValue · read-create · current Run packet burst test | ||||
| CcienaCesBenchmarkProfileEntryRfc2544Suite | 1.3.6.1.4.1.1271.2.1.39.1.1.11.1.39 | TruthValue | RC | |
column · TruthValue · read-create · current Run RFC2544 test suite which includes throughput, frame loss and latency tests | ||||
| CcienaCesBenchmarkProfileEntryY1564Test | 1.3.6.1.4.1.1271.2.1.39.1.1.11.1.40 | TruthValue | RC | |
column · TruthValue · read-create · current The Y1564 test includes the throughput, frameloss, latency and PDV tests are is run using the configured EMIX sequence. If the profile's EMIX sequence is not configured, the default generator EMIX sequence is used. Y1564 and RFC2544 are mutually exclusive. | ||||
| CcienaCesBenchmarkProfileEntryHwSessionsRequired | 1.3.6.1.4.1.1271.2.1.39.1.1.11.1.41 | Integer32 | RO | |
column · Integer32 · read-only · current This represents the number of hardware sessions
required to enable/run a test instance using
this profile according to the profile's current
configuration.
One hardware session is required for each outer tag
PCP and color configured.
Ex 1) Encap type set to dot1q, c-pcp is 0,3 and
c-color is set to green, 2 PCPs * 1 color =
2 hw sessions.
Ex 2) Encap type set to qinq, s-pcp is 0,4,5 and
s-color is set to green-yellow, then you
need 3 PCPs * 2 colors = 6 hw sessions.
Ex 3) Encap type set to untagged, only 1 hw session
is required. | ||||
| CcienaCesBenchmarkProfileEntryNumOfRef | 1.3.6.1.4.1.1271.2.1.39.1.1.11.1.42 | Integer32 | RO | |
column · Integer32 · read-only · current Number of generator test instances currently using this test profile for testing. | ||||
| CcienaCesBenchmarkProfileEntryRowStatus | 1.3.6.1.4.1.1271.2.1.39.1.1.11.1.43 | RowStatus | RC | |
column · RowStatus · read-create · current Used to manage the creation and deletion of the conceptual rows in this table. To create a row in this table, set this object to 'createAndGo'. To delete a row in this table, set this object to 'destroy'. If the entry exists, it is displayed as 'active'. | ||||
| TcienaCesBenchmarkTestInstanceTable | 1.3.6.1.4.1.1271.2.1.39.1.1.12 | NA | ||
table · not-accessible · current Table of test instance entries. | ||||
| RcienaCesBenchmarkTestInstanceEntry | 1.3.6.1.4.1.1271.2.1.39.1.1.12.1 | NA | ||
row · not-accessible · current BENCHMARK test instance characteristics. | ||||
| CcienaCesBenchmarkTestInstanceEntryId | 1.3.6.1.4.1.1271.2.1.39.1.1.12.1.1 | Integer32 | NA | |
column · Integer32 · not-accessible · current Unique identifier for the test instance. | ||||
| CcienaCesBenchmarkTestInstanceEntryName | 1.3.6.1.4.1.1271.2.1.39.1.1.12.1.2 | DisplayString (SIZE (1..46)) | RC | |
column · DisplayString (SIZE (1..46)) · read-create · current Unique name given to the test instance at creation time. | ||||
| CcienaCesBenchmarkTestInstanceEntrySubPortId | 1.3.6.1.4.1.1271.2.1.39.1.1.12.1.3 | Integer32 | RC | |
column · Integer32 · read-create · current ID of the sub-port to base this test instance on. The sub-port has to be a child of the port under test associated with an existing entity. | ||||
| CcienaCesBenchmarkTestInstanceEntryProfileId | 1.3.6.1.4.1.1271.2.1.39.1.1.12.1.4 | Integer32 | RC | |
column · Integer32 · read-create · current Id of an existing test profile to be used with the test instance as the template for testing. A test profile ID has to be specified if this test instance is associated with a generator entity. If it's a reflector test instance, a profile ID CANNOT be specified, it has to remain set 0. | ||||
| CcienaCesBenchmarkTestInstanceEntrySvid | 1.3.6.1.4.1.1271.2.1.39.1.1.12.1.5 | Integer32 | RC | |
column · Integer32 · read-create · current S VLAN ID to use for testing. For generator test instances, this over-writes the value defined in the referenced test profile if applicable (encap-type set to qinq). For reflector test instances, this has to be set to a valid s-vid accepted by the associated sub-port. A value of 0xFFFF indicates ANY s-vid. A value of 0 indicates untagged or single-tagged traffic. | ||||
| CcienaCesBenchmarkTestInstanceEntryCvid | 1.3.6.1.4.1.1271.2.1.39.1.1.12.1.6 | Integer32 | RC | |
column · Integer32 · read-create · current C VLAN ID to use for testing. For generator test instances, this over-writes the value defined in the referenced test profile if applicable (encap-type set to dot1q or qinq). For reflector test instances, this has to be set to a valid c-vid accepted by the associated sub-port. A value of 0xFFFF indicates ANY c-vid, while a value of 0 indicates untagged (s-vid also has to be set to 0). | ||||
| CcienaCesBenchmarkTestInstanceEntryUntagged | 1.3.6.1.4.1.1271.2.1.39.1.1.12.1.7 | TruthValue | RC | |
column · TruthValue · read-create · current When set to true, this indicates that the test instance is to be associated with untagged data traffic. When this is set, the cvid and svid parameters must be 0. | ||||
| CcienaCesBenchmarkTestInstanceEntryDstMac | 1.3.6.1.4.1.1271.2.1.39.1.1.12.1.8 | MacAddress | RC | |
column · MacAddress · read-create · current Destination MAC address to use for generator test instances. When set, this over writes the value specified in the referenced test profile. This field is not applicable for reflector test instances. | ||||
| CcienaCesBenchmarkTestInstanceEntryAdminState | 1.3.6.1.4.1.1271.2.1.39.1.1.12.1.9 | CienaCesBenchmarkAdminState | RC | |
column · CienaCesBenchmarkAdminState · read-create · current Indicates the administrative state of the test instance. Upon enabling a test instance, resources are allocated in hardware. For reflector test instances, this triggers the start of reflection of any test traffic received that matches the specified svid:cvid combination on the specified sub-port. | ||||
| CcienaCesBenchmarkTestInstanceEntryStarted | 1.3.6.1.4.1.1271.2.1.39.1.1.12.1.10 | TruthValue | RC | |
column · TruthValue · read-create · current Applicable to generator test instances, this indicates whether testing is in progress or not. Setting this attribute to true will initiate testing. | ||||
| CcienaCesBenchmarkTestInstanceEntryCurrentInterval | 1.3.6.1.4.1.1271.2.1.39.1.1.12.1.11 | Integer32 | RO | |
column · Integer32 · read-only · current Applicable to generator test instances, this indicates the number of intervals of the selected tests have been run, including the current one, in relation to the total number of intervals to complete. This is based on the profile's interval and duration configured. | ||||
| CcienaCesBenchmarkTestInstanceEntryTotalIntervals | 1.3.6.1.4.1.1271.2.1.39.1.1.12.1.12 | Integer32 | RO | |
column · Integer32 · read-only · current Applicable to generator test instances, this indicates the total number of intervals of the selected tests to be run by a single start command on the test instance. This is based on the profile's interval and duration configured. A value of 0 should be interpreted as unknown and -1 as indefinite. | ||||
| CcienaCesBenchmarkTestInstanceEntryLastIterStart | 1.3.6.1.4.1.1271.2.1.39.1.1.12.1.13 | DateAndTime | RO | |
column · DateAndTime · read-only · current Date and time of the last iteration that started since the last time the system was rebooted or the statistics were cleared on the test instance. | ||||
| CcienaCesBenchmarkTestInstanceEntryClearStats | 1.3.6.1.4.1.1271.2.1.39.1.1.12.1.14 | TruthValue | RC | |
column · TruthValue · read-create · current Set to true to clear the results and counters for the test instance. | ||||
| CcienaCesBenchmarkTestInstanceEntryRowStatus | 1.3.6.1.4.1.1271.2.1.39.1.1.12.1.15 | RowStatus | RC | |
column · RowStatus · read-create · current Used to manage the creation and deletion of the conceptual rows in this table. To create a row in this table, set this object to 'createAndGo'. To delete a row in this table, set this object to 'destroy'. If the entry exists, it is displayed as 'active'. | ||||
| CcienaCesBenchmarkTestInstanceEntryAssocEntityId | 1.3.6.1.4.1.1271.2.1.39.1.1.12.1.16 | Integer32 | RO | |
column · Integer32 · read-only · current ID of the entity this test instance is associated with (cienaCesBenchmarkEntityEntryId) | ||||
| CcienaCesBenchmarkTestInstanceEntryOperState | 1.3.6.1.4.1.1271.2.1.39.1.1.12.1.17 | TruthValue | RO | |
column · TruthValue · read-only · current Indicates the operational state of the test instance. When a generator test instance is operationally enabled it means the test is running and traffic is being generated. When a reflector test instance is operationally enabled it means that reflection is active on the specified svid:cvid combination. Use the cienaCesBenchmarkTestInstanceEntryAdminState to enable/disable a test instance since this field is read-only and meant to capture operational state. | ||||
| CcienaCesBenchmarkTestInstanceEntryConnectivityTest | 1.3.6.1.4.1.1271.2.1.39.1.1.12.1.18 | TruthValue | RC | |
column · TruthValue · read-create · current Applicable to generator test instances, this field is used to trigger a connectivity test on the test instance. Setting the value to true will trigger the test by transmitting 10 packets. If no error is returned then the test has passed. If a commit error is received then the test has failed. | ||||
| TcienaCesBenchmarkGenTestSessionAllocationTable | 1.3.6.1.4.1.1271.2.1.39.1.1.13 | NA | ||
table · not-accessible · current Table providing the allocation of hw test session per generator test instance Id, PCP and color. | ||||
| RcienaCesBenchmarkGenTestSessionAllocationEntry | 1.3.6.1.4.1.1271.2.1.39.1.1.13.1 | NA | ||
row · not-accessible · current Test session (aka hardware session) allocation entry. SPECIAL NOTE: It is important to know that when the associated test profile's encapsulation type is set to untagged, the last two elements of the index (PCP and color) are fixed at 1.1. The management software needs to query using index <entidyId>.<testInstandceId>.1.1 in this case, since PCP and color are irrelevant in the untagged test traffic scenario. | ||||
| CcienaCesBenchmarkGenTestSessionPcpIndex | 1.3.6.1.4.1.1271.2.1.39.1.1.13.1.1 | Integer32 (1..8) | NA | |
column · Integer32 (1..8) · not-accessible · current PCP Index. | ||||
| CcienaCesBenchmarkGenTestSessionColorIndex | 1.3.6.1.4.1.1271.2.1.39.1.1.13.1.2 | Integer32 (1..2) | NA | |
column · Integer32 (1..2) · not-accessible · current Color Index. | ||||
| CcienaCesBenchmarkGenTestSessionPcp | 1.3.6.1.4.1.1271.2.1.39.1.1.13.1.3 | Integer32 (0..7) | RO | |
column · Integer32 (0..7) · read-only · current PCP value associated with this hw session | ||||
| CcienaCesBenchmarkGenTestSessionColor | 1.3.6.1.4.1.1271.2.1.39.1.1.13.1.4 | CienaCesBenchmarkColorTest | RO | |
column · CienaCesBenchmarkColorTest · read-only · current Color of test traffic associated with this hardware session | ||||
| CcienaCesBenchmarkGenTestSessionId | 1.3.6.1.4.1.1271.2.1.39.1.1.13.1.5 | Integer32 (0..127) | RO | |
column · Integer32 (0..127) · read-only · current Id of the hardware session allocated to the given test instance id, pcp and color | ||||
| CcienaCesBenchmarkGenTestSessionEmixSequenceId | 1.3.6.1.4.1.1271.2.1.39.1.1.13.1.6 | Integer32 | RO | |
column · Integer32 · read-only · current EMIX sequence Id used with this session. If zero, it indicates that the the frame size list is being used for the test and cienaCesBenchmarkGenTestSessionCurrentPktSize indicates which packet size is currently being tested. | ||||
| CcienaCesBenchmarkGenTestSessionCurrentPktSize | 1.3.6.1.4.1.1271.2.1.39.1.1.13.1.7 | Integer32 | RO | |
column · Integer32 · read-only · current Packet size in bytes currently used by the running test. | ||||
| CcienaCesBenchmarkGenTestSessionThroughputTestState | 1.3.6.1.4.1.1271.2.1.39.1.1.13.1.8 | CienaCesBenchmarkThroughputTestState | RO | |
column · CienaCesBenchmarkThroughputTestState · read-only · current State of the throughput test for this hardware session defined by the test instance id, pcp and color | ||||
| CcienaCesBenchmarkGenTestSessionFramelossTestState | 1.3.6.1.4.1.1271.2.1.39.1.1.13.1.9 | CienaCesBenchmarkFramelossTestState | RO | |
column · CienaCesBenchmarkFramelossTestState · read-only · current State of the frameloss test for this hardware session defined by the test instance id, pcp and color | ||||
| CcienaCesBenchmarkGenTestSessionLatencyTestState | 1.3.6.1.4.1.1271.2.1.39.1.1.13.1.10 | CienaCesBenchmarkLatencyPdvTestState | RO | |
column · CienaCesBenchmarkLatencyPdvTestState · read-only · current State of the latency test for this hardware session defined by the test instance id, pcp and color | ||||
| CcienaCesBenchmarkGenTestSessionPdvTestState | 1.3.6.1.4.1.1271.2.1.39.1.1.13.1.11 | CienaCesBenchmarkLatencyPdvTestState | RO | |
column · CienaCesBenchmarkLatencyPdvTestState · read-only · current State of the PDV test for this hardware session defined by the test instance id, pcp and color | ||||
| CcienaCesBenchmarkGenTestSessionRfc2544TestState | 1.3.6.1.4.1.1271.2.1.39.1.1.13.1.12 | CienaCesBenchmarkRfc2544TestState | RO | |
column · CienaCesBenchmarkRfc2544TestState · read-only · current State of the RFC2544 test for this hardware session defined by the test instance id, pcp and color | ||||
| CcienaCesBenchmarkGenTestSessionY1564TestState | 1.3.6.1.4.1.1271.2.1.39.1.1.13.1.13 | CienaCesBenchmarkY1564TestState | RO | |
column · CienaCesBenchmarkY1564TestState · read-only · current State of the Y1564 test for this hardware session defined by the test instance id, pcp and color | ||||
| CcienaCesBenchmarkGenTestSessionCurrentRate | 1.3.6.1.4.1.1271.2.1.39.1.1.13.1.14 | Integer32 | RO | |
column · Integer32 · read-only · current Traffic rate currently used to generate packets as percent of the line rate | ||||
| CcienaCesBenchmarkGenTestSessionSamplesCompleted | 1.3.6.1.4.1.1271.2.1.39.1.1.13.1.15 | Integer32 | RO | |
column · Integer32 · read-only · current When latency and/or pdv is running, this indicates how many samples have been gathered so far. | ||||
| TcienaCesBenchmarkTestInstanceStatsTable | 1.3.6.1.4.1.1271.2.1.39.1.1.14 | NA | ||
table · not-accessible · current Table of test instance packet statistics entries. | ||||
| RcienaCesBenchmarkTestInstanceStatsEntry | 1.3.6.1.4.1.1271.2.1.39.1.1.14.1 | NA | ||
row · not-accessible · current Benchmark test instance packet statistics | ||||
| CcienaCesBenchmarkTestInstanceStatsRxPkts | 1.3.6.1.4.1.1271.2.1.39.1.1.14.1.1 | Counter64 | RO | |
column · Counter64 · read-only · current Total number of received packets for this test instance. | ||||
| CcienaCesBenchmarkTestInstanceStatsRxIpv4Pkts | 1.3.6.1.4.1.1271.2.1.39.1.1.14.1.2 | Counter64 | RO | |
column · Counter64 · read-only · current Total number of IPv4 packets received for this test instance. | ||||
| CcienaCesBenchmarkTestInstanceStatsRxIpv4UdpPkts | 1.3.6.1.4.1.1271.2.1.39.1.1.14.1.3 | Counter64 | RO | |
column · Counter64 · read-only · current Total number of IPv4 UDP packets received for this test instance. | ||||
| CcienaCesBenchmarkTestInstanceStatsRxIpv6Pkts | 1.3.6.1.4.1.1271.2.1.39.1.1.14.1.4 | Counter64 | RO | |
column · Counter64 · read-only · current Total number of IPv6 packets received for this test instance. | ||||
| CcienaCesBenchmarkTestInstanceStatsRxIpv6UdpPkts | 1.3.6.1.4.1.1271.2.1.39.1.1.14.1.5 | Counter64 | RO | |
column · Counter64 · read-only · current Total number of IPv6 UDP packets received for this test instance. | ||||
| CcienaCesBenchmarkTestInstanceStatsRxNonIpPkts | 1.3.6.1.4.1.1271.2.1.39.1.1.14.1.6 | Counter64 | RO | |
column · Counter64 · read-only · current Total number of non-IP packets received for this test instance. | ||||
| CcienaCesBenchmarkTestInstanceStatsRxUnrecognizedPkts | 1.3.6.1.4.1.1271.2.1.39.1.1.14.1.7 | Counter64 | RO | |
column · Counter64 · read-only · current Total number of unrecognized packets received for this test instance. | ||||
| CcienaCesBenchmarkTestInstanceStatsRxDuplicatePkts | 1.3.6.1.4.1.1271.2.1.39.1.1.14.1.8 | Counter64 | RO | |
column · Counter64 · read-only · current Total number of packets received with a duplicate this test instance. | ||||
| CcienaCesBenchmarkTestInstanceStatsRxDuplicatePktsOverflow | 1.3.6.1.4.1.1271.2.1.39.1.1.14.1.9 | TruthValue | RO | |
column · TruthValue · read-only · current When set to true, this indicates that the duplicate pkt counter has rolled over in hardware and therefore, cienaCesBenchmarkTestInstanceStatsRxDuplicatePkts might not be accurate. | ||||
| CcienaCesBenchmarkTestInstanceStatsRxOOOPkts | 1.3.6.1.4.1.1271.2.1.39.1.1.14.1.10 | Counter64 | RO | |
column · Counter64 · read-only · current Total number of packets received with an out of order sequence number. The sequence number was less than the expected sequence number for this test instance. | ||||
| CcienaCesBenchmarkTestInstanceStatsRxOOOPktsOverflow | 1.3.6.1.4.1.1271.2.1.39.1.1.14.1.11 | TruthValue | RO | |
column · TruthValue · read-only · current When set to true, this indicates that the out of order pkt counter has rolled over in hardware and therefore, cienaCesBenchmarkTestInstanceStatsRxOOOPkts might not be accurate. | ||||
| CcienaCesBenchmarkTestInstanceStatsRxDiscSeqNumPkts | 1.3.6.1.4.1.1271.2.1.39.1.1.14.1.12 | Counter64 | RO | |
column · Counter64 · read-only · current Total number of packets received with a sequence number greater then the expected sequence number for this test instance. | ||||
| CcienaCesBenchmarkTestInstanceStatsRxDiscSeqNumPktsOverflow | 1.3.6.1.4.1.1271.2.1.39.1.1.14.1.13 | TruthValue | RO | |
column · TruthValue · read-only · current When set to true, this indicates that the discontinuity in sequence number pkt counter has rolled over in hardware and therefore, cienaCesBenchmarkTestInstanceStatsRxDiscSeqNumPkts might not be accurate. | ||||
| CcienaCesBenchmarkTestInstanceStatsRxUdpCheckSumPkts | 1.3.6.1.4.1.1271.2.1.39.1.1.14.1.14 | Counter64 | RO | |
column · Counter64 · read-only · current Total number of UDP packets received with a UDP checksum error. | ||||
| CcienaCesBenchmarkTestInstanceStatsTxPkts | 1.3.6.1.4.1.1271.2.1.39.1.1.14.1.15 | Counter64 | RO | |
column · Counter64 · read-only · current Total number of packets transmitted for this test instance. | ||||
| TcienaCesBenchmarkGenTestSessionThroughputResultsTable | 1.3.6.1.4.1.1271.2.1.39.1.1.15 | NA | ||
table · not-accessible · current Table of BENCHMARK generator test session throughput results in Mbps. | ||||
| RcienaCesBenchmarkGenTestSessionThroughputResultsEntry | 1.3.6.1.4.1.1271.2.1.39.1.1.15.1 | NA | ||
row · not-accessible · current BENCHMARK generator test session throughput results. | ||||
| CcienaCesBenchmarkGenTestSessionThroughputResultsPcpIndex | 1.3.6.1.4.1.1271.2.1.39.1.1.15.1.1 | Integer32 (1..8) | NA | |
column · Integer32 (1..8) · not-accessible · current Index of the PCP value | ||||
| CcienaCesBenchmarkGenTestSessionThroughputResultsColorIndex | 1.3.6.1.4.1.1271.2.1.39.1.1.15.1.2 | Integer32 (1..2) | NA | |
column · Integer32 (1..2) · not-accessible · current Color index. | ||||
| CcienaCesBenchmarkGenTestSessionThroughputResultsFrameSizeIndex | 1.3.6.1.4.1.1271.2.1.39.1.1.15.1.3 | Integer32 (1..10) | NA | |
column · Integer32 (1..10) · not-accessible · current Frame size index for which those throughput results are for. When EMIX is used, in which case cienaCesBenchmarkGenTestSessionThroughputResultsEmixSequenceId is not NULL, there is only one frame size index for the given test instance Id, pcp and color. In such a case, the frame size index will be 0 and frame size will also be 0. | ||||
| CcienaCesBenchmarkGenTestSessionThroughputResultsPcp | 1.3.6.1.4.1.1271.2.1.39.1.1.15.1.4 | Integer32 (0..7) | RO | |
column · Integer32 (0..7) · read-only · current PCP value of the test packets associated with those results. | ||||
| CcienaCesBenchmarkGenTestSessionThroughputResultsColor | 1.3.6.1.4.1.1271.2.1.39.1.1.15.1.5 | CienaCesBenchmarkColorTest | RO | |
column · CienaCesBenchmarkColorTest · read-only · current Color of the test packets associated with those results. | ||||
| CcienaCesBenchmarkGenTestSessionThroughputResultsFrameSize | 1.3.6.1.4.1.1271.2.1.39.1.1.15.1.6 | Integer32 | RO | |
column · Integer32 · read-only · current Packet size in bytes. If 0, then the cienaCesBenchmarkGenTestSessionThroughputResultsEmixSequenceId indicates the ID of the EMIX sequence used for the test | ||||
| CcienaCesBenchmarkGenTestSessionThroughputResultsEmixSequenceId | 1.3.6.1.4.1.1271.2.1.39.1.1.15.1.7 | Integer32 (1..32) | RO | |
column · Integer32 (1..32) · read-only · current ID of the EMIX sequence that was used for running the test which produced these results. When 0, frame size indicates the size of the test frame associated with these results. | ||||
| CcienaCesBenchmarkGenTestSessionThroughputResultsMin | 1.3.6.1.4.1.1271.2.1.39.1.1.15.1.8 | CienaCesBenchmarkThroughputResult | RO | |
column · CienaCesBenchmarkThroughputResult · read-only · current Minimum throughput recorded for the given packet size in Mbps * 100. The value is multiplied by 100 to be able to send the results as an integer but should be divided by 100 when displayed to provide a 2 decimal point accuracy. A result of 123.45 is sent as 12345. | ||||
| CcienaCesBenchmarkGenTestSessionThroughputResultsMax | 1.3.6.1.4.1.1271.2.1.39.1.1.15.1.9 | CienaCesBenchmarkThroughputResult | RO | |
column · CienaCesBenchmarkThroughputResult · read-only · current Maximum throughput recorded for the given packet size in Mbps * 100. The value is multiplied by 100 to be able to send the results as an integer but should be divided by 100 when displayed to provide a 2 decimal point accuracy. A result of 123.45 is sent as 12345. | ||||
| CcienaCesBenchmarkGenTestSessionThroughputResultsAvg | 1.3.6.1.4.1.1271.2.1.39.1.1.15.1.10 | CienaCesBenchmarkThroughputResult | RO | |
column · CienaCesBenchmarkThroughputResult · read-only · current Average throughput recorded for the given packet size in Mbps * 100. The value is multiplied by 100 to be able to send the results as an integer but should be divided by 100 when displayed to provide a 2 decimal point accuracy. A result of 123.45 is sent as 12345. | ||||
| CcienaCesBenchmarkGenTestSessionThroughputResultsIterations | 1.3.6.1.4.1.1271.2.1.39.1.1.15.1.11 | Integer32 | RO | |
column · Integer32 · read-only · current Number of times the test has been run for this packet size. | ||||
| CcienaCesBenchmarkGenTestSessionThroughputResultsKpiResult | 1.3.6.1.4.1.1271.2.1.39.1.1.15.1.12 | CienaCesBenchmarkKpiResult | RO | |
column · CienaCesBenchmarkKpiResult · read-only · current Pass or fail results for the test which is determined by comparing the max throughput against the selected KPI test instance's throughput pass criteria. If no KPI test instance is selected for the given test instance Id, the result will be 'notApplicable'. | ||||
| TcienaCesBenchmarkGenTestSessionFramelossResultsTable | 1.3.6.1.4.1.1271.2.1.39.1.1.16 | NA | ||
table · not-accessible · current Table of BENCHMARK generator test session frameloss results. | ||||
| RcienaCesBenchmarkGenTestSessionFramelossResultsEntry | 1.3.6.1.4.1.1271.2.1.39.1.1.16.1 | NA | ||
row · not-accessible · current BENCHMARK generator test session frameloss results.
| ||||
| CcienaCesBenchmarkGenTestSessionFramelossResultsPcpIndex | 1.3.6.1.4.1.1271.2.1.39.1.1.16.1.1 | Integer32 (1..8) | NA | |
column · Integer32 (1..8) · not-accessible · current PCP index. | ||||
| CcienaCesBenchmarkGenTestSessionFramelossResultsColorIndex | 1.3.6.1.4.1.1271.2.1.39.1.1.16.1.2 | Integer32 (1..2) | NA | |
column · Integer32 (1..2) · not-accessible · current Color index. | ||||
| CcienaCesBenchmarkGenTestSessionFramelossResultsFrameSizeIndex | 1.3.6.1.4.1.1271.2.1.39.1.1.16.1.3 | Integer32 (1..10) | NA | |
column · Integer32 (1..10) · not-accessible · current Frame size index. | ||||
| CcienaCesBenchmarkGenTestSessionFramelossResultsRateIndex | 1.3.6.1.4.1.1271.2.1.39.1.1.16.1.4 | Integer32 (1..10) | NA | |
column · Integer32 (1..10) · not-accessible · current Rate index. | ||||
| CcienaCesBenchmarkGenTestSessionFramelossResultsPcp | 1.3.6.1.4.1.1271.2.1.39.1.1.16.1.5 | Integer32 (0..7) | RO | |
column · Integer32 (0..7) · read-only · current PCP value of the test packets associated with those results. | ||||
| CcienaCesBenchmarkGenTestSessionFramelossResultsColor | 1.3.6.1.4.1.1271.2.1.39.1.1.16.1.6 | CienaCesBenchmarkColorTest | RO | |
column · CienaCesBenchmarkColorTest · read-only · current Color of the test packets associated with those results. | ||||
| CcienaCesBenchmarkGenTestSessionFramelossResultsFrameSize | 1.3.6.1.4.1.1271.2.1.39.1.1.16.1.7 | Integer32 | RO | |
column · Integer32 · read-only · current Packet size in bytes. If 0, then the cienaCesBenchmarkGenTestSessionFramelossResultsEmixSequenceId indicates the ID of the EMIX sequence used for the test | ||||
| CcienaCesBenchmarkGenTestSessionFramelossResultsEmixSequenceId | 1.3.6.1.4.1.1271.2.1.39.1.1.16.1.8 | Integer32 (1..32) | RO | |
column · Integer32 (1..32) · read-only · current ID of the EMIX sequence that was used for running the test which produced these results. When 0, frame size indicates the size of the test frame associated with these results. | ||||
| CcienaCesBenchmarkGenTestSessionFramelossResultsRate | 1.3.6.1.4.1.1271.2.1.39.1.1.16.1.9 | Integer32 | RO | |
column · Integer32 · read-only · current Rate in percent of line rate. | ||||
| CcienaCesBenchmarkGenTestSessionFramelossResultsFirst | 1.3.6.1.4.1.1271.2.1.39.1.1.16.1.10 | CienaCesBenchmarkFramelossResult | RO | |
column · CienaCesBenchmarkFramelossResult · read-only · current Percentage of frames lost on first test sequence. | ||||
| CcienaCesBenchmarkGenTestSessionFramelossResultsSecond | 1.3.6.1.4.1.1271.2.1.39.1.1.16.1.11 | CienaCesBenchmarkFramelossResult | RO | |
column · CienaCesBenchmarkFramelossResult · read-only · current Percentage of frames lost on second test sequence. | ||||
| CcienaCesBenchmarkGenTestSessionFramelossResultsKpiResult | 1.3.6.1.4.1.1271.2.1.39.1.1.16.1.12 | CienaCesBenchmarkKpiResult | RO | |
column · CienaCesBenchmarkKpiResult · read-only · current Pass or fail results for the test which is determined by comparing the frameloss result against the selected KPI test instance's frameloss pass criteria. If no KPI test instance is selected for the given test instance Id, the result will be 'notApplicable'. | ||||
| CcienaCesBenchmarkGenTestSessionFramelossResultsResult | 1.3.6.1.4.1.1271.2.1.39.1.1.16.1.13 | CienaCesBenchmarkFramelossResult | RO | |
column · CienaCesBenchmarkFramelossResult · read-only · current Percentage of frames lost on the largest test sequence results. | ||||
| TcienaCesBenchmarkGenTestSessionLatencyResultsTable | 1.3.6.1.4.1.1271.2.1.39.1.1.17 | NA | ||
table · not-accessible · current Table of BENCHMARK generator test session latency results in usec. | ||||
| RcienaCesBenchmarkGenTestSessionLatencyResultsEntry | 1.3.6.1.4.1.1271.2.1.39.1.1.17.1 | NA | ||
row · not-accessible · current BENCHMARK generator test session latency results. | ||||
| CcienaCesBenchmarkGenTestSessionLatencyResultsPcpIndex | 1.3.6.1.4.1.1271.2.1.39.1.1.17.1.1 | Integer32 (1..8) | NA | |
column · Integer32 (1..8) · not-accessible · current PCP index. | ||||
| CcienaCesBenchmarkGenTestSessionLatencyResultsColorIndex | 1.3.6.1.4.1.1271.2.1.39.1.1.17.1.2 | Integer32 (1..2) | NA | |
column · Integer32 (1..2) · not-accessible · current Color index. | ||||
| CcienaCesBenchmarkGenTestSessionLatencyResultsFrameSizeIndex | 1.3.6.1.4.1.1271.2.1.39.1.1.17.1.3 | Integer32 (1..10) | NA | |
column · Integer32 (1..10) · not-accessible · current Frame size index. | ||||
| CcienaCesBenchmarkGenTestSessionLatencyResultsPcp | 1.3.6.1.4.1.1271.2.1.39.1.1.17.1.4 | Integer32 (0..7) | RO | |
column · Integer32 (0..7) · read-only · current PCP value of the test packets associated with those results. | ||||
| CcienaCesBenchmarkGenTestSessionLatencyResultsColor | 1.3.6.1.4.1.1271.2.1.39.1.1.17.1.5 | CienaCesBenchmarkColorTest | RO | |
column · CienaCesBenchmarkColorTest · read-only · current Color of the test packets associated with those results. | ||||
| CcienaCesBenchmarkGenTestSessionLatencyResultsFrameSize | 1.3.6.1.4.1.1271.2.1.39.1.1.17.1.6 | Integer32 | RO | |
column · Integer32 · read-only · current Packet size in bytes. | ||||
| CcienaCesBenchmarkGenTestSessionLatencyResultsEmixSequenceId | 1.3.6.1.4.1.1271.2.1.39.1.1.17.1.7 | Integer32 (1..32) | RO | |
column · Integer32 (1..32) · read-only · current ID of the EMIX sequence that was used for running the test which produced these results. When 0, frame size indicates the size of the test frame associated with these results. | ||||
| CcienaCesBenchmarkGenTestSessionLatencyResultsMin | 1.3.6.1.4.1.1271.2.1.39.1.1.17.1.8 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current Minimum latency recorded for the given packet size. | ||||
| CcienaCesBenchmarkGenTestSessionLatencyResultsMax | 1.3.6.1.4.1.1271.2.1.39.1.1.17.1.9 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current Maximum latency recorded for the given packet size. | ||||
| CcienaCesBenchmarkGenTestSessionLatencyResultsAvg | 1.3.6.1.4.1.1271.2.1.39.1.1.17.1.10 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current Average latency recorded for the given packet size. | ||||
| CcienaCesBenchmarkGenTestSessionLatencyResultsSamples | 1.3.6.1.4.1.1271.2.1.39.1.1.17.1.11 | Integer32 | RO | |
column · Integer32 · read-only · current Number of samples taken during the test. | ||||
| CcienaCesBenchmarkGenTestSessionLatencyResultsKpiResult | 1.3.6.1.4.1.1271.2.1.39.1.1.17.1.12 | CienaCesBenchmarkKpiResult | RO | |
column · CienaCesBenchmarkKpiResult · read-only · current Pass or fail results for the test which is determined by comparing the frameloss result against the selected KPI test instance's latency pass criteria. If no KPI test instance is selected for the given test instance Id, the result will be 'notApplicable'. | ||||
| TcienaCesBenchmarkGenTestSessionPdvResultsTable | 1.3.6.1.4.1.1271.2.1.39.1.1.18 | NA | ||
table · not-accessible · current Table of BENCHMARK generator test session packet delay variation results in usec. | ||||
| RcienaCesBenchmarkGenTestSessionPdvResultsEntry | 1.3.6.1.4.1.1271.2.1.39.1.1.18.1 | NA | ||
row · not-accessible · current BENCHMARK generator test session packet delay variation results. | ||||
| CcienaCesBenchmarkGenTestSessionPdvResultsPcpIndex | 1.3.6.1.4.1.1271.2.1.39.1.1.18.1.1 | Integer32 (1..8) | NA | |
column · Integer32 (1..8) · not-accessible · current PCP index. | ||||
| CcienaCesBenchmarkGenTestSessionPdvResultsColorIndex | 1.3.6.1.4.1.1271.2.1.39.1.1.18.1.2 | Integer32 (1..2) | NA | |
column · Integer32 (1..2) · not-accessible · current Color index. | ||||
| CcienaCesBenchmarkGenTestSessionPdvResultsFrameSizeIndex | 1.3.6.1.4.1.1271.2.1.39.1.1.18.1.3 | Integer32 (1..10) | NA | |
column · Integer32 (1..10) · not-accessible · current Frame size index associated to those PDV stats. | ||||
| CcienaCesBenchmarkGenTestSessionPdvResultsPcp | 1.3.6.1.4.1.1271.2.1.39.1.1.18.1.4 | Integer32 (0..7) | RO | |
column · Integer32 (0..7) · read-only · current PCP value of the test packets associated with those results. | ||||
| CcienaCesBenchmarkGenTestSessionPdvResultsColor | 1.3.6.1.4.1.1271.2.1.39.1.1.18.1.5 | CienaCesBenchmarkColorTest | RO | |
column · CienaCesBenchmarkColorTest · read-only · current Color of the test packets associated with those results. | ||||
| CcienaCesBenchmarkGenTestSessionPdvResultsFrameSize | 1.3.6.1.4.1.1271.2.1.39.1.1.18.1.6 | Integer32 | RO | |
column · Integer32 · read-only · current Packet size in bytes. | ||||
| CcienaCesBenchmarkGenTestSessionPdvResultsEmixSequenceId | 1.3.6.1.4.1.1271.2.1.39.1.1.18.1.7 | Integer32 (1..32) | RO | |
column · Integer32 (1..32) · read-only · current ID of the EMIX sequence that was used for running the test which produced these results. When 0, frame size indicates the size of the test frame associated with these results. | ||||
| CcienaCesBenchmarkGenTestSessionPdvResultsAvg | 1.3.6.1.4.1.1271.2.1.39.1.1.18.1.8 | Unsigned32 | RO | |
column · Unsigned32 · read-only · current Average PDV recorded for the given packet size. | ||||
| CcienaCesBenchmarkGenTestSessionPdvResultsSamples | 1.3.6.1.4.1.1271.2.1.39.1.1.18.1.9 | Integer32 | RO | |
column · Integer32 · read-only · current Number of samples used for the test. | ||||
| CcienaCesBenchmarkGenTestSessionPdvResultsKpiResult | 1.3.6.1.4.1.1271.2.1.39.1.1.18.1.10 | CienaCesBenchmarkKpiResult | RO | |
column · CienaCesBenchmarkKpiResult · read-only · current Pass or fail results for the test which is determined by comparing the frameloss result against the selected KPI test instance's throughput PDV criteria. If no KPI test instance is selected for the given test instance Id, the result will be 'notApplicable'. | ||||
| TcienaCesBenchmarkEmixCharacterSetTable | 1.3.6.1.4.1.1271.2.1.39.1.1.19 | NA | ||
table · not-accessible · current Table of BENCHMARK EMIX character set providing the list of characters that can be used in an EMIX sequence along with their corresponding frame size. | ||||
| RcienaCesBenchmarkEmixCharacterSetEntry | 1.3.6.1.4.1.1271.2.1.39.1.1.19.1 | NA | ||
row · not-accessible · current BENCHMARK EMIX character and its associated frame size. | ||||
| CcienaCesBenchmarkEmixCharacterSetEntryIndex | 1.3.6.1.4.1.1271.2.1.39.1.1.19.1.1 | Integer32 (1..26) | NA | |
column · Integer32 (1..26) · not-accessible · current Character index. | ||||
| CcienaCesBenchmarkEmixCharacterSetEntryCharacter | 1.3.6.1.4.1.1271.2.1.39.1.1.19.1.2 | DisplayString (SIZE (1)) | RO | |
column · DisplayString (SIZE (1)) · read-only · current EMIX character that can be used for creating an EMIX sequence. The character set currently includes: a b c d e f g h u v w x | ||||
| CcienaCesBenchmarkEmixCharacterSetEntryFrameSize | 1.3.6.1.4.1.1271.2.1.39.1.1.19.1.3 | DisplayString (SIZE (1..6)) | RO | |
column · DisplayString (SIZE (1..6)) · read-only · current Frame size associated with the character. For h, the frame size is the port under test's MTU and the u character is a custom frame size configurable for each EMIX. The u frame size can take a value of 64 to 10000 and defaults to 594. If u is bigger than the MTU of the port under test, it will be reduced to the same size as h. | ||||
| NcienaCesBenchmarkNotifications | 1.3.6.1.4.1.1271.2.2.39 | |||
| !cienaCesBenchmarkTestStarted | 1.3.6.1.4.1.1271.2.2.39.1 | |||
notification · current The start command has been issued for the given benchmark generator test instance, either via CLI or SNMP. The cienaCesBenchmarkEntityEntryPortId specifies the port under test when the test instance was started; the s-vid, c-vid and destination mac address used to build the test packet are also provided. | ||||
| !cienaCesBenchmarkTestStopped | 1.3.6.1.4.1.1271.2.2.39.2 | |||
notification · current The specified generator test instance has been manually stopped by the user, either via CLI or SNMP, before the testing completed. | ||||
| !cienaCesBenchmarkTestCompleted | 1.3.6.1.4.1.1271.2.2.39.3 | |||
notification · current The testing for the specified generator test instance has finished the configured number of iterations as configured in the referenced profile interval and duration. | ||||
| !cienaCesBenchmarkTestFailedThroughputKpi | 1.3.6.1.4.1.1271.2.2.39.4 | |||
notification · current The throughput test result for the specified generator test instance is below the specified throughput KPI value for the given PCP and color traffic.
| ||||
| !cienaCesBenchmarkTestFailedFramelossKpi | 1.3.6.1.4.1.1271.2.2.39.5 | |||
notification · current The frameloss test result for the specified generator test instance exceeds the specified throughput KPI value for the given PCP and color traffic.
| ||||
| !cienaCesBenchmarkTestFailedLatencyKpi | 1.3.6.1.4.1.1271.2.2.39.6 | |||
notification · current The latency test result for the specified generator test instance exceeds the specified throughput KPI value for the given PCP and color traffic.
| ||||
| !cienaCesBenchmarkTestFailedPdvKpi | 1.3.6.1.4.1.1271.2.2.39.7 | |||
notification · current The throughput test result for the specified generator test instance is below the specified throughput KPI value for the given PCP and color traffic.
| ||||
| !cienaCesBenchmarkTestIterationCompleted | 1.3.6.1.4.1.1271.2.2.39.8 | |||
notification · current An iteration of tests for the given test instance has just completed. | ||||
Textual conventions
CienaCesBenchmarkAdminStateINTEGERdisabled(1)enabled(2)Administrative state of an object.
CienaCesBenchmarkColorTestINTEGERgreen(1)greenYellow(3)greenYellowRed(4)yellow(2)Defines which traffic color needs to be tested. Green test traffic is generated with DEI bit set to 0 and uses the profile bandwidth parameter as the starting bandwidth; yellow test traffic is generated with DEI bit set to 1 and uses the profile excess-bandwidth parameter as the starting bandwidth. When testing for red, the test stream has its DEI bit set to 1 and the starting bandwidth is (excess-bandwidth * 1.25)
CienaCesBenchmarkFramelossKpiPercentUnsigned32Display hint:
d-4Percent of the frameloss test staring bandwidth, the frame loss shouldn't exceed for the test to be considered a pass. The value is given as an integer but represent a 4 decimal point percent. Ex: 0.2000 is reported as 2000.
CienaCesBenchmarkFramelossResultUnsigned32Display hint:
d-2Frame loss results in Percent of frame loss start bandwidth are sent as unsigned integer multitplied by 100 to provide a 2 decimal point accuracy. If result is 12.34 %, it is sent as 1234 and should be divided by 100 by the SNMP application retrieving the data.
CienaCesBenchmarkFramelossTestStateINTEGERdone(11)idle(1)processingFirstResults(4)processingSecondResults(7)runningFirstTest(2)runningSecondTest(5)stoppedByDurationTimer(9)stoppedByIntervalTimer(8)stoppedByUser(10)waitingForResidualFirstPackets(3)waitingForResidualSecondPackets(6)Frame loss test states
CienaCesBenchmarkKpiResultINTEGERfail(3)notAvailable(1)pass(2)Provides a pass or fail for the test results compared to the selected KPI profile's pass crieteria for the test.
CienaCesBenchmarkLatencyPdvTestStateINTEGERdone(9)idle(1)processingResults(5)sendingTraffic(2)stoppedByDurationTimer(7)stoppedByIntervalTimer(6)stoppedByUser(8)waitingForResidualPackets(4)waitingForTimestampData(3)Test state for latency and packet delay variation tests.
CienaCesBenchmarkPcpBitmapBitsDisplay hint:
xpcp0(0)pcp1(1)pcp2(2)pcp3(3)pcp4(4)pcp5(5)pcp6(6)pcp7(7)Bitmap of the VLAN PCP (Priority Code ) value to test with. When The RFC2544 test is selected in the profile, only 1 PCP bit can be set. For other tests, a test session will be run simultaneously for each PCP set in the bitmap. In the later case, the bandwidth will be distributed among the set PCPs according to the selected PCP Bandwidth allocation profile. If no such profile is configured, the bandwidth will evenly be distributed among all set PCPs.
CienaCesBenchmarkRfc2544TestStateINTEGERdone(6)idle(1)running(2)stoppedByDurationTimer(4)stoppedByIntervalTimer(3)stoppedByUser(5)RFC 2544 test suite state.
CienaCesBenchmarkThroughputKpiPercentUnsigned32Display hint:
d-4Percent of bandwidth that the maximum throughput result shouldn't go below for the test to be considered a pass. The value is given as an integer but represent a 4 decimal point percent. Ex: 0.2000 is reported as 2000.
CienaCesBenchmarkThroughputResultUnsigned32Display hint:
d-2Throughput results in Mbps are sent as unsigned integer multiplied by 100 to provide a 2 decimal point accuracy. If result is 123.45 Mbps, it is sent as 12345 and should be divided by 100 by the SNMP application retrieving the data.
CienaCesBenchmarkThroughputTestStateINTEGERdone(8)idle(1)processingResults(4)running(2)stoppedByDurationTimer(6)stoppedByIntervalTimer(5)stoppedByUser(7)txMaxThroughputForYellowTest(9)waitingForResidualPackets(3)Throughput test states
CienaCesBenchmarkY1564TestStateINTEGERdone(6)idle(1)running(2)stoppedByDurationTimer(4)stoppedByIntervalTimer(3)stoppedByUser(5)Y1564 test suite state.
Traps / Notifications
- cienaCesBenchmarkTestCompleted
1.3.6.1.4.1.1271.2.2.39.3 - cienaCesBenchmarkTestFailedFramelossKpi
1.3.6.1.4.1.1271.2.2.39.5 - cienaCesBenchmarkTestFailedLatencyKpi
1.3.6.1.4.1.1271.2.2.39.6 - cienaCesBenchmarkTestFailedPdvKpi
1.3.6.1.4.1.1271.2.2.39.7 - cienaCesBenchmarkTestFailedThroughputKpi
1.3.6.1.4.1.1271.2.2.39.4 - cienaCesBenchmarkTestIterationCompleted
1.3.6.1.4.1.1271.2.2.39.8 - cienaCesBenchmarkTestStarted
1.3.6.1.4.1.1271.2.2.39.1 - cienaCesBenchmarkTestStopped
1.3.6.1.4.1.1271.2.2.39.2