WHISP-SM-MIB
MotorolaThis module contains MIB definitions for Subscriber Modem.
snmptranslate -m WHISP-SM-MIB -Tpsnmpwalk -v2c -c <community> -m WHISP-SM-MIB <host> 1.3.6.1.4.1.161.19.1.1.13Imports
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP, OBJECT-GROUP |
|---|---|
| SNMPv2-SMI | Bits, Counter32, Counter64, Gauge32, Integer32, IpAddress, MODULE-IDENTITY, MibIdentifier, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, TimeTicks, Unsigned32, iso |
| SNMPv2-TC | DisplayString, MacAddress, PhysAddress, TEXTUAL-CONVENTION |
| WHISP-BOX-MIBV2-MIB | dhcpRfPublicIp, whispBoxEsn |
| WHISP-GLOBAL-REG-MIB | whispAps, whispBox, whispModules, whispSm |
| WHISP-TCV2-MIB | WhispLUID, WhispMACAddress |
OID tree
| Name | OID | Type | Access | Status |
|---|---|---|---|---|
| IwhispSmMibModule | 1.3.6.1.4.1.161.19.1.1.13 | |||
identity This module contains MIB definitions for Subscriber Modem. | ||||
| NwhispSmConfig | 1.3.6.1.4.1.161.19.3.2.1 | |||
| SrfScanList | 1.3.6.1.4.1.161.19.3.2.1.1 | DisplayString | RW | |
scalar · DisplayString · read-write · current RF scan list string. The frequencies vary by product and region. If the frequency list is too long an SNMP error will be returned. If this occurs please refer to OID rfScanListTable, which will allow user to enter the full range of available frequencies. String length is limited to SNMP buffer size, so while all frequencies may be set, not all may be retrieved. Special settings: 0: none. all: All frequencies in the band(s) supported by the radio will be selected. allwhole: All frequencies that are in whole 10 MHz (5600, 5610, 5620, etc) allhalf: All frequencies that are in half 10 MHz (5600, 5605, 5610, etc) all49, all51, all52: Available only for 450i 5 GHz wideband radio. all54, all57: Available only for 450 and 450i 5 GHz radios. allhalf54: (And other frequency band combinations) would select every 5 MHz in the 5.4 GHz band (5480, 5485, 5490, etc) When doing a set, separate values with comma with no white space between values. | ||||
| SpowerUpMode | 1.3.6.1.4.1.161.19.3.2.1.2 | INTEGER | RW | |
scalar · INTEGER · read-write · current SM Power Up Mode With No 802.3 Link. 0 - Power up in Operational mode. 1 - Power up in Aim mode.
| ||||
| SlanIpSm | 1.3.6.1.4.1.161.19.3.2.1.3 | IpAddress | RW | |
scalar · IpAddress · read-write · current LAN IP. | ||||
| SlanMaskSm | 1.3.6.1.4.1.161.19.3.2.1.4 | IpAddress | RW | |
scalar · IpAddress · read-write · current LAN subnet mask. | ||||
| SdefaultGwSm | 1.3.6.1.4.1.161.19.3.2.1.5 | IpAddress | RW | |
scalar · IpAddress · read-write · current Default gateway. | ||||
| SnetworkAccess | 1.3.6.1.4.1.161.19.3.2.1.6 | INTEGER | RW | |
scalar · INTEGER · read-write · current Network accessibility. Public or local IP. For multipoint only.
| ||||
| SauthKeySm | 1.3.6.1.4.1.161.19.3.2.1.7 | DisplayString | RW | |
scalar · DisplayString · read-write · current Authentication key for 128-bit. Up to 32 characters in length. | ||||
| Senable8023link | 1.3.6.1.4.1.161.19.3.2.1.8 | INTEGER | RW | deprecated |
scalar · INTEGER · read-write · deprecated To enable or disable 802.3 link. For SMs only. Deprecated: Use enable8023linkBox instead.
| ||||
| SauthKeyOption | 1.3.6.1.4.1.161.19.3.2.1.9 | INTEGER | RW | |
scalar · INTEGER · read-write · current This option is for SMs only. Backhaul timing slave always uses the set key. 0 - Use default 128-bit key. 1 - Use set 128-bit key.
| ||||
| StimingPulseGated | 1.3.6.1.4.1.161.19.3.2.1.10 | INTEGER | RW | |
scalar · INTEGER · read-write · current 0 - Disable (Always propagate the frame timing pulse). 1 - Enable (If SM out of sync then dont propagate the frame timing pulse).
| ||||
| SnaptPrivateIP | 1.3.6.1.4.1.161.19.3.2.1.11 | IpAddress | RW | |
scalar · IpAddress · read-write · current NAPT private IP address. Only the first three bytes can be changed when NAPT is enabled. | ||||
| SnaptPrivateSubnetMask | 1.3.6.1.4.1.161.19.3.2.1.12 | IpAddress | RW | |
scalar · IpAddress · read-write · current NAPT private subnet mask. Only the last byte can be changed when NAPT is enabled. The address will always be: 255.255.255.x. | ||||
| SnaptPublicIP | 1.3.6.1.4.1.161.19.3.2.1.13 | IpAddress | RW | |
scalar · IpAddress · read-write · current IP Address of NAPT Public Interface. The variable is available only when NAPT is enabled. | ||||
| SnaptPublicSubnetMask | 1.3.6.1.4.1.161.19.3.2.1.14 | IpAddress | RW | |
scalar · IpAddress · read-write · current Subnet mask for NAPT Public Interface. The variable is available only when NAPT is enabled. | ||||
| SnaptPublicGatewayIP | 1.3.6.1.4.1.161.19.3.2.1.15 | IpAddress | RW | |
scalar · IpAddress · read-write · current IP Address of NAPT Public Interface Gateway. The variable is available only when NAPT is enabled. | ||||
| SnaptRFPublicIP | 1.3.6.1.4.1.161.19.3.2.1.16 | IpAddress | RW | |
scalar · IpAddress · read-write · current IP Address of RF Public Interface. The variable is available only when NAPT is enabled. | ||||
| SnaptRFPublicSubnetMask | 1.3.6.1.4.1.161.19.3.2.1.17 | IpAddress | RW | |
scalar · IpAddress · read-write · current Subnet mask of RF Public Interface. The variable is available only when NAPT is enabled. | ||||
| SnaptRFPublicGateway | 1.3.6.1.4.1.161.19.3.2.1.18 | IpAddress | RW | |
scalar · IpAddress · read-write · current IP Address of RF Public Interface Gateway. The variable is available only when NAPT is enabled. | ||||
| SnaptEnable | 1.3.6.1.4.1.161.19.3.2.1.19 | INTEGER | RW | |
scalar · INTEGER · read-write · current To enable or disable NAPT. For multipoint only. 1=Enable NAPT, 0=Disable NAPT. Cannot be enabled with IPv6 enabled. To enable NAT, IPv6 must first be disabled.
| ||||
| SarpCacheTimeout | 1.3.6.1.4.1.161.19.3.2.1.20 | INTEGER | RW | |
scalar · INTEGER · read-write · current ARP cache time out in unit of minutes. For multipoint only. Range from 1-30. | ||||
| StcpGarbageCollectTmout | 1.3.6.1.4.1.161.19.3.2.1.21 | INTEGER | RW | |
scalar · INTEGER · read-write · current Units of minutes for TCP garbage collection. For multipoint only. Range 4-1440. | ||||
| SudpGarbageCollectTmout | 1.3.6.1.4.1.161.19.3.2.1.22 | INTEGER | RW | |
scalar · INTEGER · read-write · current Units of minutes for UDP garbage collection. For multipoint only. Range 1-1440. | ||||
| SdhcpClientEnable | 1.3.6.1.4.1.161.19.3.2.1.23 | INTEGER | RW | obsolete |
scalar · INTEGER · read-write · obsolete To enable or disable DHCP client. For multipoint SM's with NAPT enabled.
| ||||
| SdhcpServerEnable | 1.3.6.1.4.1.161.19.3.2.1.24 | INTEGER | RW | |
scalar · INTEGER · read-write · current To enable or disable DHCP server. For multipoint SM's with NAPT enabled.
| ||||
| SdhcpServerLeaseTime | 1.3.6.1.4.1.161.19.3.2.1.25 | INTEGER | RW | |
scalar · INTEGER · read-write · current Units of days for DHCP server lease time. For multipoint SM's with NAPT enabled. Range from 1-30. | ||||
| SdhcpIPStart | 1.3.6.1.4.1.161.19.3.2.1.26 | IpAddress | RW | |
scalar · IpAddress · read-write · current The last byte will be set for the starting IP that our DHCP server gives away. The first 3 bytes of the starting IP are the same as those of NAPT private IP | ||||
| SdnsAutomatic | 1.3.6.1.4.1.161.19.3.2.1.27 | INTEGER | RW | |
scalar · INTEGER · read-write · current To have DHCP Server obtain DNS information automatically or manually.
| ||||
| SprefferedDNSIP | 1.3.6.1.4.1.161.19.3.2.1.28 | IpAddress | RW | |
scalar · IpAddress · read-write · current The preferred DNS IP when we are configured for static DNS (Not used when configured for automatic DNS). | ||||
| SalternateDNSIP | 1.3.6.1.4.1.161.19.3.2.1.29 | IpAddress | RW | |
scalar · IpAddress · read-write · current The alternate DNS IP when we are configured for static DNS (Not used when configured for automatic DNS). | ||||
| SdmzIP | 1.3.6.1.4.1.161.19.3.2.1.30 | IpAddress | RW | |
scalar · IpAddress · read-write · current Only the last byte of DMZ Host IP will be set. The first 3 bytes of DMZ IP are the same as those of NAPT private IP. | ||||
| SdmzEnable | 1.3.6.1.4.1.161.19.3.2.1.31 | INTEGER | RW | |
scalar · INTEGER · read-write · current To enable or disable DMZ host functionality.
| ||||
| SdhcpNumIPsToLease | 1.3.6.1.4.1.161.19.3.2.1.32 | INTEGER | RW | |
scalar · INTEGER · read-write · current Number of IP addresses that our DHCP server can give away. | ||||
| SpppoeFilter | 1.3.6.1.4.1.161.19.3.2.1.33 | INTEGER | RW | obsolete |
scalar · INTEGER · read-write · obsolete To set PPPoE packet filter when NAT is disabled. Obsolete - Use corresponding OID in whipsBoxConfig MIB.
| ||||
| SsmbFilter | 1.3.6.1.4.1.161.19.3.2.1.34 | INTEGER | RW | obsolete |
scalar · INTEGER · read-write · obsolete To set SMB packet filter when NAT is disabled. Obsolete - Use corresponding OID in whipsBoxConfig MIB.
| ||||
| SsnmpFilter | 1.3.6.1.4.1.161.19.3.2.1.35 | INTEGER | RW | obsolete |
scalar · INTEGER · read-write · obsolete To set SNMP packet filter when NAT is disabled. Obsolete - Use corresponding OID in whipsBoxConfig MIB.
| ||||
| SuserP1Filter | 1.3.6.1.4.1.161.19.3.2.1.36 | INTEGER | RW | obsolete |
scalar · INTEGER · read-write · obsolete To set user defined port 1 packet filter when NAT is disabled. Obsolete - Use corresponding OID in whipsBoxConfig MIB.
| ||||
| SuserP2Filter | 1.3.6.1.4.1.161.19.3.2.1.37 | INTEGER | RW | obsolete |
scalar · INTEGER · read-write · obsolete To set user defined port 2 packet filter when NAT is disabled. Obsolete - Use corresponding OID in whipsBoxConfig MIB.
| ||||
| SuserP3Filter | 1.3.6.1.4.1.161.19.3.2.1.38 | INTEGER | RW | obsolete |
scalar · INTEGER · read-write · obsolete To set user defined port 3 packet filter when NAT is disabled. Obsolete - Use corresponding OID in whipsBoxConfig MIB.
| ||||
| SallOtherIpFilter | 1.3.6.1.4.1.161.19.3.2.1.39 | INTEGER | RW | obsolete |
scalar · INTEGER · read-write · obsolete To set all other IPv4 packet filter when NAT
is disabled.
Obsolete - Use corresponding OID in whipsBoxConfig MIB.
| ||||
| SupLinkBCastFilter | 1.3.6.1.4.1.161.19.3.2.1.40 | INTEGER | RW | obsolete |
scalar · INTEGER · read-write · obsolete This variable is currently obsolete.
| ||||
| SarpFilter | 1.3.6.1.4.1.161.19.3.2.1.41 | INTEGER | RW | obsolete |
scalar · INTEGER · read-write · obsolete To set ARP packet filter when NAT is disabled. Obsolete - Use corresponding OID in whipsBoxConfig MIB.
| ||||
| SallOthersFilter | 1.3.6.1.4.1.161.19.3.2.1.42 | INTEGER | RW | obsolete |
scalar · INTEGER · read-write · obsolete To set all other packet filter when NAT is disabled. Obsolete - Use corresponding OID in whipsBoxConfig MIB.
| ||||
| SuserDefinedPort1 | 1.3.6.1.4.1.161.19.3.2.1.43 | INTEGER | RW | obsolete |
scalar · INTEGER · read-write · obsolete An integer value of number one user defined port. Range:0-65535 Obsolete - Use corresponding OID in whipsBoxConfig MIB. | ||||
| Sport1TCPFilter | 1.3.6.1.4.1.161.19.3.2.1.44 | INTEGER | RW | obsolete |
scalar · INTEGER · read-write · obsolete To set user defined port 1 TCP traffic filter. Obsolete - Use corresponding OID in whipsBoxConfig MIB.
| ||||
| Sport1UDPFilter | 1.3.6.1.4.1.161.19.3.2.1.45 | INTEGER | RW | obsolete |
scalar · INTEGER · read-write · obsolete To set user defined port 1 UDP traffic filter. Obsolete - Use corresponding OID in whipsBoxConfig MIB.
| ||||
| SuserDefinedPort2 | 1.3.6.1.4.1.161.19.3.2.1.46 | INTEGER | RW | obsolete |
scalar · INTEGER · read-write · obsolete An integer value of number two user defined port. Range:0-65535 Obsolete - Use corresponding OID in whipsBoxConfig MIB. | ||||
| Sport2TCPFilter | 1.3.6.1.4.1.161.19.3.2.1.47 | INTEGER | RW | obsolete |
scalar · INTEGER · read-write · obsolete To set user defined port 2 TCP traffic filter. Obsolete - Use corresponding OID in whipsBoxConfig MIB.
| ||||
| Sport2UDPFilter | 1.3.6.1.4.1.161.19.3.2.1.48 | INTEGER | RW | obsolete |
scalar · INTEGER · read-write · obsolete To set user defined port 2 UDP traffic filter. Obsolete - Use corresponding OID in whipsBoxConfig MIB.
| ||||
| SuserDefinedPort3 | 1.3.6.1.4.1.161.19.3.2.1.49 | INTEGER | RW | obsolete |
scalar · INTEGER · read-write · obsolete An integer value of number three user defined port. Range:0-65535 Obsolete - Use corresponding OID in whipsBoxConfig MIB. | ||||
| Sport3TCPFilter | 1.3.6.1.4.1.161.19.3.2.1.50 | INTEGER | RW | obsolete |
scalar · INTEGER · read-write · obsolete To set user defined port 3 TCP traffic filter. Obsolete - Use corresponding OID in whipsBoxConfig MIB.
| ||||
| Sport3UDPFilter | 1.3.6.1.4.1.161.19.3.2.1.51 | INTEGER | RW | obsolete |
scalar · INTEGER · read-write · obsolete To set user defined port 3 UDP traffic filter. Obsolete - Use corresponding OID in whipsBoxConfig MIB.
| ||||
| SbootpcFilter | 1.3.6.1.4.1.161.19.3.2.1.52 | INTEGER | RW | obsolete |
scalar · INTEGER · read-write · obsolete To set bootp client sourced packets filter when NAT is disabled. Obsolete - Use corresponding OID in whipsBoxConfig MIB.
| ||||
| SbootpsFilter | 1.3.6.1.4.1.161.19.3.2.1.53 | INTEGER | RW | obsolete |
scalar · INTEGER · read-write · obsolete To set bootp server sourced packets filter when NAT is disabled. Obsolete - Use corresponding OID in whipsBoxConfig MIB.
| ||||
| Sip4MultFilter | 1.3.6.1.4.1.161.19.3.2.1.54 | INTEGER | RW | obsolete |
scalar · INTEGER · read-write · obsolete To set IPv4 MultiCast packets filter when NAT is disabled. Obsolete - Use corresponding OID in whipsBoxConfig MIB.
| ||||
| SingressVID | 1.3.6.1.4.1.161.19.3.2.1.55 | INTEGER | RW | deprecated |
scalar · INTEGER · read-write · deprecated Untagged ingress VID. Deprecated - Use corresponding OID in whipsBoxConfig MIB. | ||||
| SlowPriorityUplinkCIR | 1.3.6.1.4.1.161.19.3.2.1.56 | INTEGER | RW | |
scalar · INTEGER · read-write · current Low priority uplink CIR. | ||||
| SlowPriorityDownlinkCIR | 1.3.6.1.4.1.161.19.3.2.1.57 | INTEGER | RW | |
scalar · INTEGER · read-write · current Low priority downlink CIR. | ||||
| ShiPriorityChannel | 1.3.6.1.4.1.161.19.3.2.1.58 | INTEGER | RW | |
scalar · INTEGER · read-write · current Get or set the status of the High Priority Data Channel. NOTE: This can be used to enable the channel if only Low Priority Channel is enabled, for backward compatibility. It will not allow the channel to be disabled if Medium or Ultra High Priority channels are enabled. Please use dataChanCount in whispSmConfig to control the number of Data Channels enabled instead.
| ||||
| ShiPriorityUplinkCIR | 1.3.6.1.4.1.161.19.3.2.1.59 | INTEGER | RW | |
scalar · INTEGER · read-write · current High priority uplink CIR. | ||||
| ShiPriorityDownlinkCIR | 1.3.6.1.4.1.161.19.3.2.1.60 | INTEGER | RW | |
scalar · INTEGER · read-write · current High priority downlink CIR. | ||||
| SsmRateAdapt | 1.3.6.1.4.1.161.19.3.2.1.61 | INTEGER | RW | obsolete |
scalar · INTEGER · read-write · obsolete Rate adaptation parameter. 0: no rate adaptation. 1: 1x and 2x adaptation. 2: 1x,2x and 3x adaptation.
| ||||
| SupLnkDataRate | 1.3.6.1.4.1.161.19.3.2.1.62 | INTEGER | RW | |
scalar · INTEGER · read-write · current Sustained uplink bandwidth cap. | ||||
| SupLnkLimit | 1.3.6.1.4.1.161.19.3.2.1.63 | INTEGER | RW | |
scalar · INTEGER · read-write · current Burst uplink bandwidth cap. | ||||
| SdwnLnkDataRate | 1.3.6.1.4.1.161.19.3.2.1.64 | INTEGER | RW | |
scalar · INTEGER · read-write · current Sustained downlink bandwidth cap. | ||||
| SdwnLnkLimit | 1.3.6.1.4.1.161.19.3.2.1.65 | INTEGER | RW | |
scalar · INTEGER · read-write · current Burst downlink bandwidth cap. | ||||
| SdfsConfig | 1.3.6.1.4.1.161.19.3.2.1.66 | INTEGER | RW | obsolete |
scalar · INTEGER · read-write · obsolete To configure proper regions for Dynamic Frequency Shifting. For 5.2/5.4/5.7 GHz radios.
| ||||
| SethAccessFilterEnable | 1.3.6.1.4.1.161.19.3.2.1.67 | INTEGER | RW | obsolete |
scalar · INTEGER · read-write · obsolete To enable or disable Ethernet Port access filtering to SM Management Functions. (0) - Ethernet access to SM Management allowed. (1) - Ethernet access to SM Management blocked.
| ||||
| SipAccessFilterEnable | 1.3.6.1.4.1.161.19.3.2.1.68 | INTEGER | RW | |
scalar · INTEGER · read-write · current To enable or disable IP access filtering to Management functions. (0) - IP access will be allowed from all addresses. (1) - IP access will be controlled using allowedIPAccess1-3 entries.
| ||||
| SallowedIPAccess1 | 1.3.6.1.4.1.161.19.3.2.1.69 | IpAddress | RW | |
scalar · IpAddress · read-write · current Allow access to SM Management from this IP. 0 is default setting to allow from all IPs. | ||||
| SallowedIPAccess2 | 1.3.6.1.4.1.161.19.3.2.1.70 | IpAddress | RW | |
scalar · IpAddress · read-write · current Allow access to SM Management from this IP. 0 is default setting to allow from all IPs. | ||||
| SallowedIPAccess3 | 1.3.6.1.4.1.161.19.3.2.1.71 | IpAddress | RW | |
scalar · IpAddress · read-write · current Allow access to SM Management from this IP. 0 is default setting to allow from all IPs. | ||||
| SrfDhcpState | 1.3.6.1.4.1.161.19.3.2.1.72 | INTEGER | RW | |
scalar · INTEGER · read-write · current To enable or disable RF Interface DHCP feature.
| ||||
| SbCastMIR | 1.3.6.1.4.1.161.19.3.2.1.73 | INTEGER | RW | |
scalar · INTEGER · read-write · current To enable and set Broadcast/Multicast MIR feature. Use value of 0 to disable. Units are as per bCastMIRUnits variable. Set the units first and then set this value.
| ||||
| SbhsReReg | 1.3.6.1.4.1.161.19.3.2.1.74 | INTEGER | RW | obsolete |
scalar · INTEGER · read-write · obsolete Forces BHS reregistration every 24 hours. Enable forces reregistration and Disable does not. 24 Hour Encryption Refresh.
| ||||
| SsmLEDModeFlag | 1.3.6.1.4.1.161.19.3.2.1.75 | INTEGER | RW | |
scalar · INTEGER · read-write · current To set LED Panel Operation to Revised Mode(1) or to Legacy Mode(0)
| ||||
| SethAccessEnable | 1.3.6.1.4.1.161.19.3.2.1.76 | INTEGER | RW | |
scalar · INTEGER · read-write · current To enable or disable Ethernet Port access to SM Management Functions. (1) - Ethernet access to SM Management allowed. (0) - Ethernet access to SM Management blocked.
| ||||
| SpppoeEnable | 1.3.6.1.4.1.161.19.3.2.1.77 | INTEGER | RW | |
scalar · INTEGER · read-write · current Enable or disable PPPoE on the SM. NAT MUST be enabled prior and Translation Bridging MUST be DISABLED on the AP.
| ||||
| SpppoeAuthenticationType | 1.3.6.1.4.1.161.19.3.2.1.78 | INTEGER | RW | |
scalar · INTEGER · read-write · current Set the PPPoE Authentication Type to either None or CHAP/pap
| ||||
| SpppoeAccessConcentrator | 1.3.6.1.4.1.161.19.3.2.1.79 | DisplayString | RW | |
scalar · DisplayString · read-write · current Set the PPPoE Access Concentrator Name. Less than or equal to 32 characters | ||||
| SpppoeServiceName | 1.3.6.1.4.1.161.19.3.2.1.80 | DisplayString | RW | |
scalar · DisplayString · read-write · current Set the PPPoE Service Name. Less than or equal to 32 characters | ||||
| SpppoeUserName | 1.3.6.1.4.1.161.19.3.2.1.81 | DisplayString | RW | |
scalar · DisplayString · read-write · current Set the PPPoE Username. Less than or equal to 32 characters | ||||
| SpppoePassword | 1.3.6.1.4.1.161.19.3.2.1.82 | DisplayString | RW | |
scalar · DisplayString · read-write · current Set the PPPoE Password. Less than or equal to 32 characters | ||||
| SpppoeTCPMSSClampEnable | 1.3.6.1.4.1.161.19.3.2.1.83 | INTEGER | RW | |
scalar · INTEGER · read-write · current Enable or disable TCP MSS Clamping. Enabling this will cause the SM to edit the TCP MSS in TCP SYN and SYN-ACK packets. This will allow for a workaround for MTU issues so that the TCP session will only go up to the clamped MSS. If you are using PMTUD reliably, this should not be needed.
| ||||
| SpppoeMTUOverrideEnable | 1.3.6.1.4.1.161.19.3.2.1.84 | INTEGER | RW | |
scalar · INTEGER · read-write · current Enable the overriding of the PPP link's MTU. Normally, the PPP link will set the MTU to the MRU of the PPPoE Server, but this may be overridden. If the MRU of the PPPoE server is smaller than the desired MTU, the smaller MTU will be used.
| ||||
| SpppoeMTUOverrideValue | 1.3.6.1.4.1.161.19.3.2.1.85 | INTEGER (0..1492) | RW | |
scalar · INTEGER (0..1492) · read-write · current Enable the overriding of the PPP link's MTU. Normally, the PPP link will set the MTU to the MRU of the PPPoE Server, but this may be overridden. If the MRU of the PPPoE server is smaller than the desired MTU, the smaller MTU will be used. Max MTU of a PPPoE link is 1492. | ||||
| SpppoeTimerType | 1.3.6.1.4.1.161.19.3.2.1.86 | INTEGER | RW | |
scalar · INTEGER · read-write · current Set the PPPoE Timer type. Can be a Keep Alive timer where the link will be checked periodically and automatically redialed if the link is down. Also could be an Idle Timeout where the link will be automatically dropped after an idle period and redialed if user data is present. Keep Alive timers are in seconds while Idle Timeout timers are in minutes.
| ||||
| SpppoeTimeoutPeriod | 1.3.6.1.4.1.161.19.3.2.1.87 | INTEGER | RW | |
scalar · INTEGER · read-write · current The Timeout Period. The use of this depends on the Timer Type. If the Timer Type is KeepAlive, then the timeout period is in seconds. If the Timer Type is Idle Timeout, then the timeout period is in minutes. Minimum values are 20 seconds for KeepAlive timer, and 5 minutes for Idle Timeout. | ||||
| StimedSpectrumAnalysisDuration | 1.3.6.1.4.1.161.19.3.2.1.88 | INTEGER (10..1000) | RW | deprecated |
scalar · INTEGER (10..1000) · read-write · deprecated As of release 13.0.2 this value is deprecated. Please use the OID in whispBoxConfig. Value in seconds for a timed spectrum analysis. Range is 10-1000 seconds. Note that this represents the minimum scan duration. The current scan will still be allowed to complete when this duration is elapsed, so actual scan time could be longer. | ||||
| SspectrumAnalysisOnBoot | 1.3.6.1.4.1.161.19.3.2.1.89 | INTEGER | RW | deprecated |
scalar · INTEGER · read-write · deprecated As of release 15.1.5 this value is deprecated. Please use the OID in whispBoxConfig. To enable or disable Spectrum Analysis on boot up for one scan through the band. (0) - Disabled (1) - Enabled
| ||||
| SspectrumAnalysisAction | 1.3.6.1.4.1.161.19.3.2.1.90 | INTEGER | RW | deprecated |
scalar · INTEGER · read-write · deprecated As of release 13.0.2, this OID has been deprecated. Please use the OID in whispBoxConfig. Start or stop timed or continuous Spectrum Analysis and also give status. (0) - Stop Spectrum Analysis (1) - Start Timed Spectrum Analysis (2) - Start Continuous Spectrum Analysis (3) - Idle, no Spectrum Analysis results. (4) - Idle, Spectrum Analysis results available. (5) - Timed or Remote Spectrum Analysis in progress. (6) - Continuous Spectrum Analysis in progress. Note: Continuous mode has a max of 24 hours.
| ||||
| SpppoeConnectOD | 1.3.6.1.4.1.161.19.3.2.1.91 | INTEGER | RW | |
scalar · INTEGER · read-write · current Force a manual PPPoE connection attempt.
| ||||
| SpppoeDisconnectOD | 1.3.6.1.4.1.161.19.3.2.1.92 | INTEGER | RW | |
scalar · INTEGER · read-write · current Force a manual PPPoE disconnection.
| ||||
| SsmAntennaType | 1.3.6.1.4.1.161.19.3.2.1.93 | INTEGER | RW | obsolete |
scalar · INTEGER · read-write · obsolete Deprecated. See whispBoxStatus.antType for antenna type information.
| ||||
| SnatConnectionType | 1.3.6.1.4.1.161.19.3.2.1.94 | INTEGER | RW | |
scalar · INTEGER · read-write · current To configure the SM NAT connection type. Options are Static IP, DHCP, or PPPoE.
| ||||
| SwanPingReplyEnable | 1.3.6.1.4.1.161.19.3.2.1.95 | INTEGER | RW | |
scalar · INTEGER · read-write · current Allow Ping replies from SM WAN interface. Applies to both NAT and PPPoE WAN interfaces.
| ||||
| SpacketFilterDirection | 1.3.6.1.4.1.161.19.3.2.1.96 | INTEGER | RW | obsolete |
scalar · INTEGER · read-write · obsolete To packet filter direction when NAT is disabled. Upstream is default. Obsolete - Use corresponding OID in whipsBoxConfig MIB.
| ||||
| ScolorCode2 | 1.3.6.1.4.1.161.19.3.2.1.97 | INTEGER (0..254) | RW | obsolete |
scalar · INTEGER (0..254) · read-write · obsolete Second Color code. The variable is obsolete. See additionalColorCode in whispSmConfig. | ||||
| ScolorCodepriority2 | 1.3.6.1.4.1.161.19.3.2.1.98 | INTEGER | RW | obsolete |
scalar · INTEGER · read-write · obsolete Priority setting for the second color code. The variable is obsolete. See additionalColorCodePriority in whispSmConfig.
| ||||
| ScolorCode3 | 1.3.6.1.4.1.161.19.3.2.1.99 | INTEGER (0..254) | RW | obsolete |
scalar · INTEGER (0..254) · read-write · obsolete Third Color code. The variable is obsolete. See additionalColorCode in whispSmConfig. | ||||
| ScolorCodepriority3 | 1.3.6.1.4.1.161.19.3.2.1.100 | INTEGER | RW | obsolete |
scalar · INTEGER · read-write · obsolete Priority setting for the third color code. The variable is obsolete. See additionalColorCodePriority in whispSmConfig.
| ||||
| ScolorCode4 | 1.3.6.1.4.1.161.19.3.2.1.101 | INTEGER (0..254) | RW | obsolete |
scalar · INTEGER (0..254) · read-write · obsolete Fourth Color code. The variable is obsolete. See additionalColorCode in whispSmConfig. | ||||
| ScolorCodepriority4 | 1.3.6.1.4.1.161.19.3.2.1.102 | INTEGER | RW | obsolete |
scalar · INTEGER · read-write · obsolete Priority setting for the fourth color code. The variable is obsolete. See additionalColorCodePriority in whispSmConfig.
| ||||
| ScolorCode5 | 1.3.6.1.4.1.161.19.3.2.1.103 | INTEGER (0..254) | RW | obsolete |
scalar · INTEGER (0..254) · read-write · obsolete Fifth Color code. The variable is obsolete. See additionalColorCode in whispSmConfig. | ||||
| ScolorCodepriority5 | 1.3.6.1.4.1.161.19.3.2.1.104 | INTEGER | RW | obsolete |
scalar · INTEGER · read-write · obsolete Priority setting for the fifth color code. The variable is obsolete. See additionalColorCodePriority in whispSmConfig.
| ||||
| ScolorCode6 | 1.3.6.1.4.1.161.19.3.2.1.105 | INTEGER (0..254) | RW | obsolete |
scalar · INTEGER (0..254) · read-write · obsolete Sixth Color code. The variable is obsolete. See additionalColorCode in whispSmConfig. | ||||
| ScolorCodepriority6 | 1.3.6.1.4.1.161.19.3.2.1.106 | INTEGER | RW | obsolete |
scalar · INTEGER · read-write · obsolete Priority setting for the sixth color code. The variable is obsolete. See additionalColorCodePriority in whispSmConfig.
| ||||
| ScolorCode7 | 1.3.6.1.4.1.161.19.3.2.1.107 | INTEGER (0..254) | RW | obsolete |
scalar · INTEGER (0..254) · read-write · obsolete Seventh Color code. The variable is obsolete. See additionalColorCode in whispSmConfig. | ||||
| ScolorCodepriority7 | 1.3.6.1.4.1.161.19.3.2.1.108 | INTEGER | RW | obsolete |
scalar · INTEGER · read-write · obsolete Priority setting for the seventh color code. The variable is obsolete. See additionalColorCodePriority in whispSmConfig.
| ||||
| ScolorCode8 | 1.3.6.1.4.1.161.19.3.2.1.109 | INTEGER (0..254) | RW | obsolete |
scalar · INTEGER (0..254) · read-write · obsolete Eighth Color code. The variable is obsolete. See additionalColorCode in whispSmConfig. | ||||
| ScolorCodepriority8 | 1.3.6.1.4.1.161.19.3.2.1.110 | INTEGER | RW | obsolete |
scalar · INTEGER · read-write · obsolete Priority setting for the eighth color code. The variable is obsolete. See additionalColorCodePriority in whispSmConfig.
| ||||
| ScolorCode9 | 1.3.6.1.4.1.161.19.3.2.1.111 | INTEGER (0..254) | RW | obsolete |
scalar · INTEGER (0..254) · read-write · obsolete Ninth Color code. The variable is obsolete. See additionalColorCode in whispSmConfig. | ||||
| ScolorCodepriority9 | 1.3.6.1.4.1.161.19.3.2.1.112 | INTEGER | RW | obsolete |
scalar · INTEGER · read-write · obsolete Priority setting for the ninth color code. The variable is obsolete. See additionalColorCodePriority in whispSmConfig.
| ||||
| ScolorCode10 | 1.3.6.1.4.1.161.19.3.2.1.113 | INTEGER (0..254) | RW | obsolete |
scalar · INTEGER (0..254) · read-write · obsolete Tenth Color code. The variable is obsolete. See additionalColorCode in whispSmConfig. | ||||
| ScolorCodepriority10 | 1.3.6.1.4.1.161.19.3.2.1.114 | INTEGER | RW | obsolete |
scalar · INTEGER · read-write · obsolete Priority setting for the tenth color code. The variable is obsolete. See additionalColorCodePriority in whispSmConfig.
| ||||
| SnatDNSProxyEnable | 1.3.6.1.4.1.161.19.3.2.1.115 | INTEGER | RW | |
scalar · INTEGER · read-write · current If enabled, the SM will advertise itself as the DNS server when it sends out DHCP client leases and forward DNS queries automatically. If disabled, the SM will forward on upstream DNS server information when it sends out DHCP client leases.
| ||||
| SallIpv4Filter | 1.3.6.1.4.1.161.19.3.2.1.116 | INTEGER | RW | obsolete |
scalar · INTEGER · read-write · obsolete To set all IPv4 packet filter when NAT
is disabled. Enabling this will automatically enable all of the known IP filters (SMB, SNMP, Bootp,
IPv4 Mcast, User Defined Ports, and All Other IPv4).
Obsolete - Use corresponding OID in whipsBoxConfig MIB.
| ||||
| SspectrumAnalysisDisplay | 1.3.6.1.4.1.161.19.3.2.1.117 | INTEGER | RW | |
scalar · INTEGER · read-write · current The display for Spectrum Analyzer: (0) - Averaging over entire period (1) - Instantaneous showing the last reading
| ||||
| SsyslogSMXmitSetting | 1.3.6.1.4.1.161.19.3.2.1.118 | INTEGER | RW | deprecated |
scalar · INTEGER · read-write · deprecated Obtains Syslog transmit configuration from AP/BHM if set to 0, overrides if 1 or 2. Transmits syslog data to Syslog server if enabled(1), stops if disabled (2).
| ||||
| SsyslogServerApPreferred | 1.3.6.1.4.1.161.19.3.2.1.119 | INTEGER | RW | |
scalar · INTEGER · read-write · current Uses Syslog server configuration from AP/BHM if enabled and available, otherwise uses local configuration.
| ||||
| SsyslogMinLevelApPreferred | 1.3.6.1.4.1.161.19.3.2.1.120 | INTEGER | RW | |
scalar · INTEGER · read-write · current Uses Syslog minimum transmit level configuration from AP/BHM if available, otherwise uses local configuration.
| ||||
| SsyslogSMXmitControl | 1.3.6.1.4.1.161.19.3.2.1.121 | INTEGER | RW | |
scalar · INTEGER · read-write · current Obtains Syslog transmit configuration from AP/BHM if available, or specifies the local transmit state.
| ||||
| SoneXBridgingMode | 1.3.6.1.4.1.161.19.3.2.1.122 | INTEGER | RW | |
scalar · INTEGER · read-write · current This sets the bridging mode for 802.1x authentication.
| ||||
| SoneXAuthMode | 1.3.6.1.4.1.161.19.3.2.1.123 | INTEGER | RW | |
scalar · INTEGER · read-write · current This sets the Authentication mode for 802.1x authentication.
| ||||
| SoneXVlan | 1.3.6.1.4.1.161.19.3.2.1.124 | INTEGER | RW | |
scalar · INTEGER · read-write · current VLAN to negotiate 802.1x. | ||||
| SeapPeerAAAServerCommonName | 1.3.6.1.4.1.161.19.3.2.1.126 | DisplayString | RW | |
scalar · DisplayString · read-write · current THIS OID IS CURRENTLY UNUSED: EAP Peer Server Common Name | ||||
| SrfScanListBandFilter | 1.3.6.1.4.1.161.19.3.2.1.127 | INTEGER | RW | obsolete |
scalar · INTEGER · read-write · obsolete This element is obsolete.
| ||||
| SupLnkMaxBurstDataRate | 1.3.6.1.4.1.161.19.3.2.1.128 | INTEGER | RW | |
scalar · INTEGER · read-write · current Maximum burst uplink rate.
| ||||
| SdwnLnkMaxBurstDataRate | 1.3.6.1.4.1.161.19.3.2.1.129 | INTEGER | RW | |
scalar · INTEGER · read-write · current Maximum burst downlink rate.
| ||||
| ScyclicPrefixScan | 1.3.6.1.4.1.161.19.3.2.1.130 | DisplayString | RW | |
scalar · DisplayString · read-write · current Cyclic Prefix value for frequency scanning used by MIMO SMs only. When setting use a comma delimited list of cyclic prefixes with no spaces. For example: 1/8,1/16 | ||||
| SbandwidthScan | 1.3.6.1.4.1.161.19.3.2.1.131 | DisplayString | RW | |
scalar · DisplayString · read-write · current Bandwidth values for frequency scanning used by MIMO SMs only. When setting use a comma delimited list of bandwidths. For example: 10, 20 | ||||
| SapSelection | 1.3.6.1.4.1.161.19.3.2.1.132 | INTEGER | RW | |
scalar · INTEGER · read-write · current This OID affects what AP to attempt to register to when Canopy SMs scan see more than one AP that are valid in it's configuration. (0) - Default, Canopy radios after scanning select the best AP that will optimize for estimated throughput. (1) - Select the AP with the best receive power level. Note this is only if multiple APs fit the current scan configuration, and will be overriden by color codes, RADIUS, etc.
| ||||
| SradioBandscanConfig | 1.3.6.1.4.1.161.19.3.2.1.133 | INTEGER | RW | |
scalar · INTEGER · read-write · current Used to determine when frequency, cyclic prefix and bandwidth settings take effect for band scanning MIMO SMs. 0 - Instant 1 - Delayed 2 - Apply changes
| ||||
| Sforcepoweradjust | 1.3.6.1.4.1.161.19.3.2.1.134 | INTEGER | RW | |
scalar · INTEGER · read-write · current This will force an SM or BHS to initiate an asynchronous power adjust sequence. This is done automatically every minute if power adjust is enabled. | ||||
| SclearBerrResults | 1.3.6.1.4.1.161.19.3.2.1.135 | INTEGER | RW | |
scalar · INTEGER · read-write · current This will clear the BER results. | ||||
| Sberrautoupdateflag | 1.3.6.1.4.1.161.19.3.2.1.136 | INTEGER | RW | |
scalar · INTEGER · read-write · current This indicates if the once a second BERR updating of counters is enabled. 1 = enabled 0 = disabled | ||||
| StestSMBER | 1.3.6.1.4.1.161.19.3.2.1.137 | INTEGER | RW | |
scalar · INTEGER · read-write · current 0 - Disable (Return the SM to a normal operation state). 1 - Enable (Set SM into a BER test state).
| ||||
| SallowedIPAccessNMLength1 | 1.3.6.1.4.1.161.19.3.2.1.138 | INTEGER (1..32) | RW | |
scalar · INTEGER (1..32) · read-write · current Length of the network mask to apply to the AllowedIPAddress when assessing if access is allowed | ||||
| SallowedIPAccessNMLength2 | 1.3.6.1.4.1.161.19.3.2.1.139 | INTEGER (1..32) | RW | |
scalar · INTEGER (1..32) · read-write · current Length of the network mask to apply to the AllowedIPAddress when assessing if access is allowed | ||||
| SallowedIPAccessNMLength3 | 1.3.6.1.4.1.161.19.3.2.1.140 | INTEGER (1..32) | RW | |
scalar · INTEGER (1..32) · read-write · current Length of the network mask to apply to the AllowedIPAddress when assessing if access is allowed | ||||
| SnaptRemoteManage | 1.3.6.1.4.1.161.19.3.2.1.141 | INTEGER | RW | |
scalar · INTEGER · read-write · current To enable or disable Remote Management. For multipoint only. 0=Disable Remote Management, 1=Enable - Standalone Config, 2=Enable - Use WAN Interface.
| ||||
| SspectrumAnalysisScanBandwidth | 1.3.6.1.4.1.161.19.3.2.1.142 | INTEGER | RW | |
scalar · INTEGER · read-write · current Scanning Bandwidth used for the Spectrum Analyzer. Only available on PMP 450.
| ||||
| SberDeModSelect | 1.3.6.1.4.1.161.19.3.2.1.143 | INTEGER | RO | |
scalar · INTEGER · read-only · current The BER demodulation level at the SM. 0 for QPSK, 1 for 16-QAM, 2 for 64-QAM, 3 for 256-QAM, 4 for 8-QAM, 5 for 32-QAM, 6 for 128-QAM.
| ||||
| SmulticastVCRcvRate | 1.3.6.1.4.1.161.19.3.2.1.144 | DisplayString | RO | |
scalar · DisplayString · read-only · current Multicast VC Receive Rate | ||||
| Spmp430ApRegistrationOptions | 1.3.6.1.4.1.161.19.3.2.1.145 | INTEGER | RW | obsolete |
scalar · INTEGER · read-write · obsolete Obsolete. The 430 SM only supports PMP 450 interoperability mode.
| ||||
| SswitchRadioModeAndReboot | 1.3.6.1.4.1.161.19.3.2.1.146 | INTEGER | RW | obsolete |
scalar · INTEGER · read-write · obsolete As of 14.2, the 430 SM no longer supports multiple radio modes. It only support 450 interoperability mode.
| ||||
| SnatTslTableSize | 1.3.6.1.4.1.161.19.3.2.1.147 | INTEGER (1024..8192) | RW | |
scalar · INTEGER (1024..8192) · read-write · current NAT Translation Table Size. Range 1024-8192. | ||||
| SingressVIDPriority | 1.3.6.1.4.1.161.19.3.2.1.148 | INTEGER (0..7) | RW | deprecated |
scalar · INTEGER (0..7) · read-write · deprecated ingress VID VLAN Priority. Deprecated - Use corresponding OID in whipsBoxConfig MIB. | ||||
| SingressVIDPriorityMode | 1.3.6.1.4.1.161.19.3.2.1.149 | INTEGER | RW | obsolete |
scalar · INTEGER · read-write · obsolete ingress VID VLAN Priority Mode. Obsolete - Use corresponding OID in whipsBoxConfig MIB.
| ||||
| SproviderVIDPriority | 1.3.6.1.4.1.161.19.3.2.1.150 | INTEGER (0..7) | RW | |
scalar · INTEGER (0..7) · read-write · current Provider VID VLAN Priority. | ||||
| SproviderVIDPriorityMode | 1.3.6.1.4.1.161.19.3.2.1.151 | INTEGER | RW | |
scalar · INTEGER · read-write · current Provider VID VLAN Priority Mode.
| ||||
| SadditionalColorCode | 1.3.6.1.4.1.161.19.3.2.1.152 | INTEGER (0..254) | RW | |
scalar · INTEGER (0..254) · read-write · current Add an additional color code. Setting additionalColorCode and additionalColorCodePriority adds an entry. | ||||
| SadditionalColorCodePriority | 1.3.6.1.4.1.161.19.3.2.1.153 | INTEGER | RW | |
scalar · INTEGER · read-write · current Add an additional color code priority. Setting additionalColorCode and additionalColorCodePriority adds an entry.
| ||||
| SdeleteAdditionalColorCode | 1.3.6.1.4.1.161.19.3.2.1.154 | INTEGER (0..254) | RW | |
scalar · INTEGER (0..254) · read-write · current Delete an additional color code. | ||||
| SbCastMIRUnits | 1.3.6.1.4.1.161.19.3.2.1.155 | INTEGER | RW | |
scalar · INTEGER · read-write · current Units of Broadcast/Multicast MIR value. Set units first and then bCastMIR
| ||||
| TrfScanListTable | 1.3.6.1.4.1.161.19.3.2.1.156 | NA | ||
table · not-accessible · current The list of configured scanning frequencies on the SM or BHS. | ||||
| RrfScanListEntry | 1.3.6.1.4.1.161.19.3.2.1.156.1 | NA | ||
row · not-accessible · current Entry of configured scanning frequencies on the SM or BHS.
| ||||
| CrfScanListFrequency | 1.3.6.1.4.1.161.19.3.2.1.156.1.1 | INTEGER (0..9000000) | RW | |
column · INTEGER (0..9000000) · read-write · current RF scan list toggle. The frequencies vary by product and region. A get on the table will display the all the frequencies currently checked for scan. A set on this OID will add a frequency to the scan list, if it is not already added. If the frequency is already in the list, a set on this OID will remove the frequency from the list. See rfScanListFrequencyAdd and rfScanListFrequencyRemove for explicit add/remove. | ||||
| StxPowerControl | 1.3.6.1.4.1.161.19.3.2.1.157 | INTEGER | RW | |
scalar · INTEGER · read-write · current Enable/Disable Automatic control of SM Tx power. Engineering use only.
| ||||
| SbridgeTableSize | 1.3.6.1.4.1.161.19.3.2.1.158 | INTEGER | RW | |
scalar · INTEGER · read-write · current Bridge Table Size : 1 -- 4096. | ||||
| SbridgeTableRestrict | 1.3.6.1.4.1.161.19.3.2.1.159 | INTEGER | RW | |
scalar · INTEGER · read-write · current Restrict forwarding packets from hosts for which MAC address is not in the bridge table.
| ||||
| SmaxTxPowerEnable | 1.3.6.1.4.1.161.19.3.2.1.160 | INTEGER | RW | |
scalar · INTEGER · read-write · current Enable Max Tx Power configuration. This is used with OID maxTxPower to set the max transmit power. This might be required in certain regions and frequency bands. See User Guide for more information. Enabling this will not allow a radio to transmit above its EIRP limit. The AP's Transmit Power Control may still adjust the Tx power down.
| ||||
| SmaxTxPower | 1.3.6.1.4.1.161.19.3.2.1.161 | INTEGER | RW | |
scalar · INTEGER · read-write · current This OID is controlled by OID maxTxPowerEnable. This might be required in certain regions and frequency bands. See user guide for more information. Setting this will not allow a radio to transmit above its EIRP limit. The AP's Transmit Power Control may still adjust the Tx power down. | ||||
| SmedPriorityChannel | 1.3.6.1.4.1.161.19.3.2.1.162 | INTEGER | RO | |
scalar · INTEGER · read-only · current Get the status of the Medium Priority Data Channel. Read only. Please use dataChanCount in whispSmConfig to control the number of Priority Channels enabled.
| ||||
| SuHiPriorityChannel | 1.3.6.1.4.1.161.19.3.2.1.163 | INTEGER | RO | |
scalar · INTEGER · read-only · current Get the status of the Ultra High Priority Data Channel. Read only. Please use dataChanCount in whispSmConfig to control the number of Data Channels enabled.
| ||||
| SuHiPriorityUplinkCIR | 1.3.6.1.4.1.161.19.3.2.1.164 | INTEGER | RW | |
scalar · INTEGER · read-write · current Ultra High priority uplink CIR. | ||||
| SuHiPriorityDownlinkCIR | 1.3.6.1.4.1.161.19.3.2.1.165 | INTEGER | RW | |
scalar · INTEGER · read-write · current Ultra High priority downlink CIR. | ||||
| SsmPrioritizationGroup | 1.3.6.1.4.1.161.19.3.2.1.166 | INTEGER | RW | |
scalar · INTEGER · read-write · current SM Prioritization Group. Indicates the group in which this SM will belong for SM Prioritization.
| ||||
| SauthKey256Sm | 1.3.6.1.4.1.161.19.3.2.1.167 | DisplayString | RW | |
scalar · DisplayString · read-write · current Authentication key for 256-bit. Up to 64 characters in length. | ||||
| SauthKey256Option | 1.3.6.1.4.1.161.19.3.2.1.168 | INTEGER | RW | |
scalar · INTEGER · read-write · current This option is for SMs only. Backhaul timing slave always uses the set key. 0 - Use default 256-bit key. 1 - Use set 256-bit key.
| ||||
| SmedPriorityUplinkCIR | 1.3.6.1.4.1.161.19.3.2.1.169 | INTEGER | RW | |
scalar · INTEGER · read-write · current Medium priority uplink CIR. | ||||
| SmedPriorityDownlinkCIR | 1.3.6.1.4.1.161.19.3.2.1.170 | INTEGER | RW | |
scalar · INTEGER · read-write · current Medium priority downlink CIR. | ||||
| SdataChanCount | 1.3.6.1.4.1.161.19.3.2.1.171 | INTEGER | RW | |
scalar · INTEGER · read-write · current Number of Data Channels enabled. Minimum is 1 (Low Priority), and subsequent channels are enabled in order of: High, Medium, Ultra High priority. NOTE: PMP 430 only supports 2 channels.
| ||||
| NwhispPropSchedulerConfig | 1.3.6.1.4.1.161.19.3.2.1.172 | |||
| SdownlinkPlan | 1.3.6.1.4.1.161.19.3.2.1.172.1 | INTEGER | RW | |
scalar · INTEGER · read-write · current Downlink plan in Kbps. | ||||
| SuplinkPlan | 1.3.6.1.4.1.161.19.3.2.1.172.2 | INTEGER | RW | |
scalar · INTEGER · read-write · current Uplink plan in Kbps. | ||||
| Sweight | 1.3.6.1.4.1.161.19.3.2.1.172.3 | INTEGER | RW | |
scalar · INTEGER · read-write · current SM Weight (0.1 to 9.9) for proportional scheduling. To set value should be multiplied by 10 for example 1.5 * 10 = 15 | ||||
| SuserLockModulation | 1.3.6.1.4.1.161.19.3.2.1.172.4 | INTEGER | RW | |
scalar · INTEGER · read-write · current SM User lock Modulation.
| ||||
| SlockedModulation | 1.3.6.1.4.1.161.19.3.2.1.172.5 | INTEGER | RW | |
scalar · INTEGER · read-write · current SM locked Modulation.
| ||||
| SthresholdModulation | 1.3.6.1.4.1.161.19.3.2.1.172.6 | INTEGER | RW | |
scalar · INTEGER · read-write · current SM Threshold Modulation.
| ||||
| SdlReferenceEVM | 1.3.6.1.4.1.161.19.3.2.1.173 | DisplayString | RW | |
scalar · DisplayString · read-write · current Downlink reference EVM used for LQI calculations. | ||||
| SulReferenceEVM | 1.3.6.1.4.1.161.19.3.2.1.174 | DisplayString | RW | |
scalar · DisplayString · read-write · current Uplink reference EVM used for LQI calculations. | ||||
| SaddPortFwdMap | 1.3.6.1.4.1.161.19.3.2.1.176 | DisplayString | RW | |
scalar · DisplayString · read-write · current Add a new port forward mapping in the following format {Internal IP,Internal Port,External Port,Protocols (0=All, 1=UDP, 2=TCP)}.
For example 169.254.1.1,80,8080,2 | ||||
| SrfScanListFrequencyAdd | 1.3.6.1.4.1.161.19.3.2.1.177 | INTEGER (0..9000000) | RW | |
scalar · INTEGER (0..9000000) · read-write · current Add a frequency to the scan list. The frequencies vary by product and region. A get on this OID will return 0. A set on this OID will add a frequency, and return no error if it is already added. | ||||
| SrfScanListFrequencyRemove | 1.3.6.1.4.1.161.19.3.2.1.178 | INTEGER (0..9000000) | RW | |
scalar · INTEGER (0..9000000) · read-write · current Remove a frequency from the scan list. The frequencies vary by product and region. A get on this OID will return 0. A set on this OID will remove a frequency from the scan list. The set will return no error even if the frequency is not present in the list to remove. | ||||
| SenableGps | 1.3.6.1.4.1.161.19.3.2.1.179 | INTEGER | RW | |
scalar · INTEGER · read-write · current Enable(1)/Disable(0) GPS data on SM. Always enabled for platforms with an onboard GPS.
| ||||
| SremovePortFwdMap | 1.3.6.1.4.1.161.19.3.2.1.180 | DisplayString | RW | |
scalar · DisplayString · read-write · current Remove a port forward mapping in the following format {Internal IP,Internal Port,External Port,Protocols (0=All, 1=UDP, 2=TCP)}.
For example 169.254.1.1,80,8080,2 | ||||
| NwhispSmStatus | 1.3.6.1.4.1.161.19.3.2.2 | |||
| SsessionStatus | 1.3.6.1.4.1.161.19.3.2.2.1 | DisplayString | RO | |
scalar · DisplayString · read-only · current SM registered or not. | ||||
| Srssi | 1.3.6.1.4.1.161.19.3.2.2.2 | INTEGER | RO | |
scalar · INTEGER · read-only · current Radio signal strength index. FSK only. | ||||
| Sjitter | 1.3.6.1.4.1.161.19.3.2.2.3 | Gauge32 (0..15) | RO | obsolete |
scalar · Gauge32 (0..15) · read-only · obsolete A measure of multipath interference. Applicable to FSK radios only. Obsolete. | ||||
| SairDelay | 1.3.6.1.4.1.161.19.3.2.2.4 | Unsigned32 | RO | obsolete |
scalar · Unsigned32 · read-only · obsolete Round trip delay in bits. FSK only. This OID is obsolete. For OFDM use OID airDelayns. | ||||
| SradioSlicingSm | 1.3.6.1.4.1.161.19.3.2.2.5 | INTEGER | RO | obsolete |
scalar · INTEGER · read-only · obsolete This variable is obsolete. | ||||
| SradioTxGainSm | 1.3.6.1.4.1.161.19.3.2.2.6 | INTEGER | RO | deprecated |
scalar · INTEGER · read-only · deprecated Radio transmission gain setting. Applicable to FSK radios only. | ||||
| ScalibrationStatus | 1.3.6.1.4.1.161.19.3.2.2.7 | DisplayString | RO | deprecated |
scalar · DisplayString · read-only · deprecated Varible deprecated. Please use calibrationStatusBox. | ||||
| SradioDbm | 1.3.6.1.4.1.161.19.3.2.2.8 | DisplayString | RO | |
scalar · DisplayString · read-only · current Rx Power level. For MIMO this is the combined power of the horizontal and vertical paths. | ||||
| SregisteredToAp | 1.3.6.1.4.1.161.19.3.2.2.9 | DisplayString | RO | |
scalar · DisplayString · read-only · current Registered AP's MAC address. | ||||
| SdhcpCip | 1.3.6.1.4.1.161.19.3.2.2.10 | IpAddress | RO | |
scalar · IpAddress · read-only · current Assigned IP address to DHCP client. | ||||
| SdhcpSip | 1.3.6.1.4.1.161.19.3.2.2.11 | IpAddress | RO | |
scalar · IpAddress · read-only · current Public DHCP server IP. | ||||
| SdhcpClientLease | 1.3.6.1.4.1.161.19.3.2.2.12 | TimeTicks | RO | |
scalar · TimeTicks · read-only · current DHCP client lease time. | ||||
| SdhcpCSMask | 1.3.6.1.4.1.161.19.3.2.2.13 | IpAddress | RO | |
scalar · IpAddress · read-only · current Public DHCP server subnet mask. | ||||
| SdhcpDfltRterIP | 1.3.6.1.4.1.161.19.3.2.2.14 | IpAddress | RO | |
scalar · IpAddress · read-only · current Public default router IP address. | ||||
| Sdhcpcdns1 | 1.3.6.1.4.1.161.19.3.2.2.15 | IpAddress | RO | |
scalar · IpAddress · read-only · current Primary public domain name server. | ||||
| Sdhcpcdns2 | 1.3.6.1.4.1.161.19.3.2.2.16 | IpAddress | RO | |
scalar · IpAddress · read-only · current Secondary public domain name server. | ||||
| Sdhcpcdns3 | 1.3.6.1.4.1.161.19.3.2.2.17 | IpAddress | RO | |
scalar · IpAddress · read-only · current Third public domain name server. | ||||
| SdhcpDomName | 1.3.6.1.4.1.161.19.3.2.2.18 | DisplayString | RO | |
scalar · DisplayString · read-only · current Public domain name server. | ||||
| TdhcpServerTable | 1.3.6.1.4.1.161.19.3.2.2.19 | NA | ||
table · not-accessible · current The table of DHCP server hosts. | ||||
| RdhcpServerEntry | 1.3.6.1.4.1.161.19.3.2.2.19.1 | NA | ||
| ChostIp | 1.3.6.1.4.1.161.19.3.2.2.19.1.1 | IpAddress | RO | |
column · IpAddress · read-only · current DHCP server IP address. | ||||
| ChostMacAddress | 1.3.6.1.4.1.161.19.3.2.2.19.1.2 | PhysAddress | RO | |
column · PhysAddress · read-only · current Private host MAC address. | ||||
| ChostLease | 1.3.6.1.4.1.161.19.3.2.2.19.1.3 | TimeTicks | RO | |
column · TimeTicks · read-only · current Lease time assigned by DHCP server host. | ||||
| SadaptRate | 1.3.6.1.4.1.161.19.3.2.2.20 | DisplayString | RO | |
scalar · DisplayString · read-only · current Uplink adapt rate. | ||||
| SradioDbmInt | 1.3.6.1.4.1.161.19.3.2.2.21 | INTEGER | RO | |
scalar · INTEGER · read-only · current Radio power level(integer). For MIMO radios this is the combined power of the horiztontal and vertical paths. | ||||
| SdfsStatus | 1.3.6.1.4.1.161.19.3.2.2.22 | DisplayString | RO | |
scalar · DisplayString · read-only · current Dynamic frequency shifting status. For DFS Radio only. | ||||
| SradioTxPwr | 1.3.6.1.4.1.161.19.3.2.2.23 | DisplayString | RO | |
scalar · DisplayString · read-only · current Tx Power level. | ||||
| SactiveRegion | 1.3.6.1.4.1.161.19.3.2.2.24 | DisplayString | RO | |
scalar · DisplayString · read-only · current The active region of the radio. | ||||
| SsnmpBerLevel | 1.3.6.1.4.1.161.19.3.2.2.25 | INTEGER | RO | |
scalar · INTEGER · read-only · current BER level. For PMP 450 systems: 2=MIMO QPSK, 4=MIMO 16-QAM, 6=MIMO64-QAM, 8=256-QAM For non PMP 450: 2=2 level BER, 4=4 level BER.
| ||||
| SnbBitsRcvd | 1.3.6.1.4.1.161.19.3.2.2.26 | Counter64 | RO | |
scalar · Counter64 · read-only · current Number of BER bits received. | ||||
| SnbPriBitsErr | 1.3.6.1.4.1.161.19.3.2.2.27 | Counter32 | RO | obsolete |
scalar · Counter32 · read-only · obsolete Number of Primary bit errors (non MIMO platforms only). | ||||
| SnbSndBitsErr | 1.3.6.1.4.1.161.19.3.2.2.28 | Counter32 | RO | obsolete |
scalar · Counter32 · read-only · obsolete Number of secondary bit errors (non MIMO platforms only). | ||||
| SprimaryBER | 1.3.6.1.4.1.161.19.3.2.2.29 | INTEGER | RO | obsolete |
scalar · INTEGER · read-only · obsolete Obsoleted, invalid type to represent this data. Measured Primary Bit Error Rate. | ||||
| SsecondaryBER | 1.3.6.1.4.1.161.19.3.2.2.30 | INTEGER | RO | obsolete |
scalar · INTEGER · read-only · obsolete Obsoleted, invalid type to represent this data. Measured Secondary Bit Error Rate. | ||||
| StotalBER | 1.3.6.1.4.1.161.19.3.2.2.31 | INTEGER | RO | obsolete |
scalar · INTEGER · read-only · obsolete Obsoleted, invalid type to represent this data. Measured Total Bit Error Rate. | ||||
| SminRSSI | 1.3.6.1.4.1.161.19.3.2.2.32 | INTEGER | RO | obsolete |
scalar · INTEGER · read-only · obsolete Measured Min. RSSI. Applicable to FSK radios only. Obsolete. | ||||
| SmaxRSSI | 1.3.6.1.4.1.161.19.3.2.2.33 | INTEGER | RO | obsolete |
scalar · INTEGER · read-only · obsolete Measured Max. RSSI. Applicable to FSK radios only. Obsolete. | ||||
| SminJitter | 1.3.6.1.4.1.161.19.3.2.2.34 | Gauge32 (0..15) | RO | obsolete |
scalar · Gauge32 (0..15) · read-only · obsolete Measured Min. Jitter. Applicable to FSK radios only. Obsolete. | ||||
| SmaxJitter | 1.3.6.1.4.1.161.19.3.2.2.35 | Gauge32 (0..15) | RO | obsolete |
scalar · Gauge32 (0..15) · read-only · obsolete Measured Max. Jitter. Applicable to FSK radios only. Obsolete. | ||||
| SsmSessionTimer | 1.3.6.1.4.1.161.19.3.2.2.36 | TimeTicks | RO | |
scalar · TimeTicks · read-only · current SM current session timer. | ||||
| SpppoeSessionStatus | 1.3.6.1.4.1.161.19.3.2.2.37 | DisplayString | RO | |
scalar · DisplayString · read-only · current Current PPPoE Session Status | ||||
| SpppoeSessionID | 1.3.6.1.4.1.161.19.3.2.2.38 | INTEGER | RO | |
scalar · INTEGER · read-only · current Current PPPoE Session ID | ||||
| SpppoeIPCPAddress | 1.3.6.1.4.1.161.19.3.2.2.39 | IpAddress | RO | |
scalar · IpAddress · read-only · current Current PPPoE IPCP IP Address | ||||
| SpppoeMTUOverrideEn | 1.3.6.1.4.1.161.19.3.2.2.40 | INTEGER | RO | |
scalar · INTEGER · read-only · current Current PPPoE MTU Override Setting
| ||||
| SpppoeMTUValue | 1.3.6.1.4.1.161.19.3.2.2.41 | INTEGER | RO | |
scalar · INTEGER · read-only · current Current PPPoE MTU Value | ||||
| SpppoeTimerTypeValue | 1.3.6.1.4.1.161.19.3.2.2.42 | INTEGER | RO | |
scalar · INTEGER · read-only · current Current PPPoE Timer Type. 0 is disabled, 1 is Keep Alive timer, and 2 is Idle Timeout timer.
| ||||
| SpppoeTimeoutValue | 1.3.6.1.4.1.161.19.3.2.2.43 | INTEGER | RO | |
scalar · INTEGER · read-only · current Current PPPoE Timeout Period. The use of this depends on the Timer Type. If the Timer Type is KeepAlive, then the timeout period is in seconds. If the Timer Type is Idle Timeout, then the timeout period is in minutes. | ||||
| SpppoeDNSServer1 | 1.3.6.1.4.1.161.19.3.2.2.44 | IpAddress | RO | |
scalar · IpAddress · read-only · current PPPoE DNS Server 1 | ||||
| SpppoeDNSServer2 | 1.3.6.1.4.1.161.19.3.2.2.45 | IpAddress | RO | |
scalar · IpAddress · read-only · current PPPoE DNS Server 2 | ||||
| SpppoeControlBytesSent | 1.3.6.1.4.1.161.19.3.2.2.46 | Counter32 | RO | |
scalar · Counter32 · read-only · current PPPoE Control Bytes Sent | ||||
| SpppoeControlBytesReceived | 1.3.6.1.4.1.161.19.3.2.2.47 | Counter32 | RO | |
scalar · Counter32 · read-only · current PPPoE Control Bytes Received | ||||
| SpppoeDataBytesSent | 1.3.6.1.4.1.161.19.3.2.2.48 | Counter32 | RO | |
scalar · Counter32 · read-only · current PPPoE Data Bytes Sent | ||||
| SpppoeDataBytesReceived | 1.3.6.1.4.1.161.19.3.2.2.49 | Counter32 | RO | |
scalar · Counter32 · read-only · current PPPoE Data Bytes Received | ||||
| SpppoeEnabledStatus | 1.3.6.1.4.1.161.19.3.2.2.50 | INTEGER | RO | |
scalar · INTEGER · read-only · current PPPoE Enabled
| ||||
| SpppoeTCPMSSClampEnableStatus | 1.3.6.1.4.1.161.19.3.2.2.51 | INTEGER | RO | |
scalar · INTEGER · read-only · current PPPoE TCP MSS Clamping Enable
| ||||
| SpppoeACNameStatus | 1.3.6.1.4.1.161.19.3.2.2.52 | DisplayString | RO | |
scalar · DisplayString · read-only · current Current PPPoE Access Concentrator In Use | ||||
| SpppoeSvcNameStatus | 1.3.6.1.4.1.161.19.3.2.2.53 | DisplayString | RO | |
scalar · DisplayString · read-only · current Current PPPoE Service Name In Use | ||||
| SpppoeSessUptime | 1.3.6.1.4.1.161.19.3.2.2.54 | TimeTicks | RO | |
scalar · TimeTicks · read-only · current Uptime of current PPPoE Session in ticks | ||||
| SprimaryBERDisplay | 1.3.6.1.4.1.161.19.3.2.2.55 | DisplayString | RO | obsolete |
scalar · DisplayString · read-only · obsolete Measured Primary Bit Error Rate. Non MIMO platforms only. | ||||
| SsecondaryBERDisplay | 1.3.6.1.4.1.161.19.3.2.2.56 | DisplayString | RO | obsolete |
scalar · DisplayString · read-only · obsolete Measured Secondary Bit Error Rate. FSK platforms only. | ||||
| StotalBERDisplay | 1.3.6.1.4.1.161.19.3.2.2.57 | DisplayString | RO | |
scalar · DisplayString · read-only · current Measured Total Bit Error Rate. For MIMO this is combined both paths. | ||||
| SminRadioDbm | 1.3.6.1.4.1.161.19.3.2.2.58 | INTEGER | RO | |
scalar · INTEGER · read-only · current Maximum receive power of beacon in dBm. For MIMO radios, this is in the vertical path. | ||||
| SmaxRadioDbm | 1.3.6.1.4.1.161.19.3.2.2.59 | INTEGER | RO | |
scalar · INTEGER · read-only · current Maximum receive power in dBm (rounded to nearest integer). | ||||
| SpppoeSessIdleTime | 1.3.6.1.4.1.161.19.3.2.2.60 | TimeTicks | RO | |
scalar · TimeTicks · read-only · current Idle Time of current PPPoE Session in ticks | ||||
| SradioDbmAvg | 1.3.6.1.4.1.161.19.3.2.2.61 | INTEGER | RO | |
scalar · INTEGER · read-only · current Average Receive Power of the AP's beacon in dBm. OFDM Radios only. For MIMO this is only the verical path. | ||||
| SzoltarFPGAFreqOffset | 1.3.6.1.4.1.161.19.3.2.2.62 | INTEGER | RO | deprecated |
scalar · INTEGER · read-only · deprecated No longer supported. | ||||
| SzoltarSWFreqOffset | 1.3.6.1.4.1.161.19.3.2.2.63 | INTEGER | RO | deprecated |
scalar · INTEGER · read-only · deprecated No longer supported. | ||||
| SairDelayns | 1.3.6.1.4.1.161.19.3.2.2.64 | INTEGER | RO | |
scalar · INTEGER · read-only · current Round trip delay in nanoseconds. | ||||
| ScurrentColorCode | 1.3.6.1.4.1.161.19.3.2.2.65 | INTEGER | RO | |
scalar · INTEGER · read-only · current The current Color Code of the Registered AP/BHM. A value of -1 is return when the device is not registered. | ||||
| ScurrentColorCodePri | 1.3.6.1.4.1.161.19.3.2.2.66 | INTEGER | RO | |
scalar · INTEGER · read-only · current The current priority of the Registered color code
| ||||
| ScurrentChanFreq | 1.3.6.1.4.1.161.19.3.2.2.67 | Unsigned32 | RO | |
scalar · Unsigned32 · read-only · current The Current Channel Frequency of the AP/BHM when in session. | ||||
| SlinkQualityBeacon | 1.3.6.1.4.1.161.19.3.2.2.68 | DisplayString | RO | |
scalar · DisplayString · read-only · current Engineering only. Link Quality for incoming beacons. For Gen II OFDM radios and forward. | ||||
| SdhcpServerPktXmt | 1.3.6.1.4.1.161.19.3.2.2.72 | Counter32 | RO | |
scalar · Counter32 · read-only · current Number of packets transmitted by SM DHCP Server | ||||
| SdhcpServerPktRcv | 1.3.6.1.4.1.161.19.3.2.2.73 | Counter32 | RO | |
scalar · Counter32 · read-only · current Number of packets received by SM DHCP Server | ||||
| SdhcpServerPktToss | 1.3.6.1.4.1.161.19.3.2.2.74 | Counter32 | RO | |
scalar · Counter32 · read-only · current Number of packets tossed by SM DHCP Server | ||||
| SreceiveFragmentsModulationPercentage | 1.3.6.1.4.1.161.19.3.2.2.86 | DisplayString | RO | |
scalar · DisplayString · read-only · current Engineering use only. The percentage of recent fragments received at which modulation. For Gen II OFDM only and forward. | ||||
| SfragmentsReceived1XVertical | 1.3.6.1.4.1.161.19.3.2.2.87 | Counter32 | RO | |
scalar · Counter32 · read-only · current Engineering use only. Number of fragments received in 1x modulation. For GenII OFDM only and forward. For MIMO this is the vertical path. | ||||
| SfragmentsReceived2XVertical | 1.3.6.1.4.1.161.19.3.2.2.88 | Counter32 | RO | |
scalar · Counter32 · read-only · current Engineering use only. Number of fragments received in 2x modulation. For GenII OFDM only and forward. For MIMO this is the vertical path. | ||||
| SfragmentsReceived3XVertical | 1.3.6.1.4.1.161.19.3.2.2.89 | Counter32 | RO | |
scalar · Counter32 · read-only · current Engineering use only. Number of fragments received in 3x modulation. For GenII OFDM only and forward. For MIMO this is the vertical path. | ||||
| SfragmentsReceived4XVertical | 1.3.6.1.4.1.161.19.3.2.2.90 | Counter32 | RO | |
scalar · Counter32 · read-only · current Engineering use only. Number of fragments received in 4x modulation. For GenII OFDM only and forward. For MIMO this is the vertical path. | ||||
| SlinkQualityData1XVertical | 1.3.6.1.4.1.161.19.3.2.2.91 | DisplayString | RO | |
scalar · DisplayString · read-only · current Engineering use only. Link Quality for the data VC for QPSK modulation (1X). For Gen II OFDM radios and forward only. For MIMO this is the vertical path. | ||||
| SlinkQualityData2XVertical | 1.3.6.1.4.1.161.19.3.2.2.92 | DisplayString | RO | |
scalar · DisplayString · read-only · current Engineering use only. Link Quality for the data VC for 16-QAM modulation (2X). For Gen II OFDM radios and forward only. For MIMO this is the vertical path. | ||||
| SlinkQualityData3XVertical | 1.3.6.1.4.1.161.19.3.2.2.93 | DisplayString | RO | |
scalar · DisplayString · read-only · current Engineering use only. Link Quality for the data VC for 64-QAM modulation (3X). For Gen II OFDM radios and forward only. For MIMO this is the vertical path. | ||||
| SlinkQualityData4XVertical | 1.3.6.1.4.1.161.19.3.2.2.94 | DisplayString | RO | |
scalar · DisplayString · read-only · current Engineering use only. Link Quality for the data VC for 256-QAM modulation (4X). For Gen II OFDM radios and forward only. For MIMO this is the vertical path. | ||||
| SsignalToNoiseRatioSMVertical | 1.3.6.1.4.1.161.19.3.2.2.95 | INTEGER | RO | |
scalar · INTEGER · read-only · current An estimated signal to noise ratio based on the last received data. For GenII OFDM only and forward. For MIMO this is the vertical antenna. Will return zero if Signal to Noise Ratio Calculation is disabled. | ||||
| SrfStatTxSuppressionCount | 1.3.6.1.4.1.161.19.3.2.2.96 | Counter32 | RO | |
scalar · Counter32 · read-only · current RF Scheduler Stats DFS TX Suppression Count | ||||
| SbridgecbUplinkCreditRate | 1.3.6.1.4.1.161.19.3.2.2.97 | Unsigned32 | RO | |
scalar · Unsigned32 · read-only · current Sustained uplink data rate. | ||||
| SbridgecbUplinkCreditLimit | 1.3.6.1.4.1.161.19.3.2.2.98 | Unsigned32 | RO | |
scalar · Unsigned32 · read-only · current Uplink Burst Allocation. | ||||
| SbridgecbDownlinkCreditRate | 1.3.6.1.4.1.161.19.3.2.2.99 | Unsigned32 | RO | |
scalar · Unsigned32 · read-only · current Sustained uplink data rate. | ||||
| SbridgecbDownlinkCreditLimit | 1.3.6.1.4.1.161.19.3.2.2.100 | Unsigned32 | RO | |
scalar · Unsigned32 · read-only · current Uplink Burst Allocation. | ||||
| SmimoQpskBerDisplay | 1.3.6.1.4.1.161.19.3.2.2.101 | DisplayString | RO | |
scalar · DisplayString · read-only · current QPSK BER statistics. MIMO platforms only. | ||||
| Smimo16QamBerDisplay | 1.3.6.1.4.1.161.19.3.2.2.102 | DisplayString | RO | |
scalar · DisplayString · read-only · current 16-QAM BER statistics MIMO platforms only. Engineering use only. | ||||
| Smimo64QamBerDisplay | 1.3.6.1.4.1.161.19.3.2.2.103 | DisplayString | RO | |
scalar · DisplayString · read-only · current 64-QAM BER statistics MIMO platforms only. Engineering use only. | ||||
| Smimo256QamBerDisplay | 1.3.6.1.4.1.161.19.3.2.2.104 | DisplayString | RO | |
scalar · DisplayString · read-only · current 256-QAM BER statistics MIMO platforms only. Engineering use only. | ||||
| SmimoBerRcvModulationType | 1.3.6.1.4.1.161.19.3.2.2.105 | DisplayString | RO | |
scalar · DisplayString · read-only · current Receive modulation type. MIMO platforms only. | ||||
| SsignalToNoiseRatioSMHorizontal | 1.3.6.1.4.1.161.19.3.2.2.106 | INTEGER | RO | |
scalar · INTEGER · read-only · current An estimated signal to noise ratio based on the last received data for horizontal antenna. MIMO radios only. Will return zero if Signal to Noise Ratio Calculation is disabled. When operating in MIMO-A will return 0. | ||||
| SmaxRadioDbmObsoleted | 1.3.6.1.4.1.161.19.3.2.2.107 | INTEGER | RO | obsolete |
scalar · INTEGER · read-only · obsolete This OID was inadvertently moved in 12.0.2. Please use maxRadioDbm. This OID is obsoleted in 21.0. | ||||
| SsignalStrengthRatio | 1.3.6.1.4.1.161.19.3.2.2.108 | DisplayString | RO | |
scalar · DisplayString · read-only · current Signal Strength Ratio in dB is the power received by the vertical antenna input (dB) - power received by the horizontal antenna input (dB). MIMO radios only. | ||||
| SfragmentsReceived1XHorizontal | 1.3.6.1.4.1.161.19.3.2.2.109 | Counter32 | RO | |
scalar · Counter32 · read-only · current Engineering use only. Number of fragments received in 1x modulation. For MIMO radios only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical. | ||||
| SfragmentsReceived2XHorizontal | 1.3.6.1.4.1.161.19.3.2.2.110 | Counter32 | RO | |
scalar · Counter32 · read-only · current Engineering use only. Number of fragments received in 2x modulation. For MIMO radios only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical. | ||||
| SfragmentsReceived3XHorizontal | 1.3.6.1.4.1.161.19.3.2.2.111 | Counter32 | RO | |
scalar · Counter32 · read-only · current Engineering use only. Number of fragments received in 3x modulation. For MIMO radios only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical. | ||||
| SfragmentsReceived4XHorizontal | 1.3.6.1.4.1.161.19.3.2.2.112 | Counter32 | RO | |
scalar · Counter32 · read-only · current Engineering use only. Number of fragments received in 4x modulation. For MIMO radios only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical. | ||||
| SlinkQualityData1XHorizontal | 1.3.6.1.4.1.161.19.3.2.2.113 | DisplayString | RO | |
scalar · DisplayString · read-only · current Engineering use only. Link Quality for the data VC for QPSK modulation (1X). For MIMO radios only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical. | ||||
| SlinkQualityData2XHorizontal | 1.3.6.1.4.1.161.19.3.2.2.114 | DisplayString | RO | |
scalar · DisplayString · read-only · current Engineering use only. Link Quality for the data VC for 16-QAM modulation (2X). For MIMO radios only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical. | ||||
| SlinkQualityData3XHorizontal | 1.3.6.1.4.1.161.19.3.2.2.115 | DisplayString | RO | |
scalar · DisplayString · read-only · current Engineering use only. Link Quality for the data VC for 64-QAM modulation (3X). For MIMO radios only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical. | ||||
| SlinkQualityData4XHorizontal | 1.3.6.1.4.1.161.19.3.2.2.116 | DisplayString | RO | |
scalar · DisplayString · read-only · current Engineering use only. Link Quality for the data VC for 256-QAM modulation (4X). For MIMO radios only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical. | ||||
| SradioDbmHorizontal | 1.3.6.1.4.1.161.19.3.2.2.117 | DisplayString | RO | |
scalar · DisplayString · read-only · current Receive power level of the horizontal antenna in dBm. MIMO radios only. | ||||
| SradioDbmVertical | 1.3.6.1.4.1.161.19.3.2.2.118 | DisplayString | RO | |
scalar · DisplayString · read-only · current Receive power level of the vertical antenna in dBm. MIMO radios only. | ||||
| SbridgecbDownlinkMaxBurstBitRate | 1.3.6.1.4.1.161.19.3.2.2.119 | Unsigned32 | RO | |
scalar · Unsigned32 · read-only · current Maximum burst downlink rate. | ||||
| SbridgecbUplinkMaxBurstBitRate | 1.3.6.1.4.1.161.19.3.2.2.120 | Unsigned32 | RO | |
scalar · Unsigned32 · read-only · current Maximum burst uplink Rate. | ||||
| ScurrentCyclicPrefix | 1.3.6.1.4.1.161.19.3.2.2.121 | INTEGER | RO | |
scalar · INTEGER · read-only · current The Current Cyclic Prefix of the AP/BHM when in session.
| ||||
| ScurrentBandwidth | 1.3.6.1.4.1.161.19.3.2.2.122 | INTEGER | RO | |
scalar · INTEGER · read-only · current The Current Bandwidth of the AP/BHM when in session.
| ||||
| SberPwrRxFPGAPathA | 1.3.6.1.4.1.161.19.3.2.2.123 | INTEGER | RO | |
scalar · INTEGER · read-only · current BER power level on FPGA Rx Path A of SM. Engineering Use Only. | ||||
| SberPwrRxFPGAPathB | 1.3.6.1.4.1.161.19.3.2.2.124 | INTEGER | RO | |
scalar · INTEGER · read-only · current BER power level on FPGA Rx Path B of SM. Engineering Use Only. | ||||
| SrawBERPwrRxPathA | 1.3.6.1.4.1.161.19.3.2.2.125 | INTEGER | RO | |
scalar · INTEGER · read-only · current Raw unadjusted BER power level on FPGA Rx Path A of SM. Engineering Use Only. | ||||
| SrawBERPwrRxPathB | 1.3.6.1.4.1.161.19.3.2.2.126 | INTEGER | RO | |
scalar · INTEGER · read-only · current Raw unadjusted BER power level on FPGA Rx Path B of SM. Engineering Use Only. | ||||
| SradioModeStatus | 1.3.6.1.4.1.161.19.3.2.2.127 | INTEGER | RO | obsolete |
scalar · INTEGER · read-only · obsolete The current radio mode that SM is operating in. PMP 430 SMs only. As of 14.2, the 430 SM only supports PMP 450 interoperability mode, so this will only return pmp450Interoperability.
| ||||
| SadaptRateLowPri | 1.3.6.1.4.1.161.19.3.2.2.128 | INTEGER | RO | |
scalar · INTEGER · read-only · current The current transmitting rate of the low priority VC. 0 : SM is not in session 1 : 1X QPSK MIMO-A/SISO 2 : 2X 16-QAM MIMO-A/SISO or QPSK MIMO-B 3 : 3X 64-QAM MIMO-A/SISO or 8-QAM MIMO-B 4 : 4X 256-QAM MIMO-A/SISO or 16-QAM MIMO-B 5 : 5X 32-QAM MIMO-B 6 : 6X 64-QAM MIMO-B 7 : 7X 128-QAM MIMO-B 8 : 8X 256-QAM MIMO-B NOTE: As of 15.2 for 450 platform, the adapt rates are the same per LUID. This OID will provide this common per LUID rate.
| ||||
| SadaptRateHighPri | 1.3.6.1.4.1.161.19.3.2.2.129 | INTEGER | RO | deprecated |
scalar · INTEGER · read-only · deprecated The current transmitting rate of the high priority VC. -1 : High Priority Channel not configured 0 : SM is not in session 1 : 1X QPSK MIMO-A/SISO 2 : 2X 16-QAM MIMO-A/SISO or QPSK MIMO-B 3 : 3X 64-QAM MIMO-A/SISO or 8-QAM MIMO-B 4 : 4X 256-QAM MIMO-A/SISO or 16-QAM MIMO-B 5 : 5X 32-QAM MIMO-B 6 : 6X 64-QAM MIMO-B 7 : 7X 128-QAM MIMO-B 8 : 8X 256-QAM MIMO-B NOTE: As of 15.2 for 450 platform, the adapt rates are the same per LUID. OID adaptRateLowPri will provide this common per LUID rate.
| ||||
| SbitErrorsQSPKpathA | 1.3.6.1.4.1.161.19.3.2.2.130 | Counter64 | RO | |
scalar · Counter64 · read-only · current Number of bit errors received from BER packet at QPSK path A. Valid MIMO platforms only. | ||||
| SbitErrorsQSPKpathB | 1.3.6.1.4.1.161.19.3.2.2.131 | Counter64 | RO | |
scalar · Counter64 · read-only · current Number of bit errors received from BER packet at QPSK path B. Valid MIMO platforms only. | ||||
| SbitErrors16QAMpathA | 1.3.6.1.4.1.161.19.3.2.2.132 | Counter64 | RO | |
scalar · Counter64 · read-only · current Number of bit errors received from BER packet at 16-QAM path A. Valid MIMO platforms only. Engineering use only. | ||||
| SbitErrors16QAMpathB | 1.3.6.1.4.1.161.19.3.2.2.133 | Counter64 | RO | |
scalar · Counter64 · read-only · current Number of bit errors received from BER packet at 16-QAM path B. Valid MIMO platforms only. Engineering use only. | ||||
| SbitErrors64QAMpathA | 1.3.6.1.4.1.161.19.3.2.2.134 | Counter64 | RO | |
scalar · Counter64 · read-only · current Number of bit errors received from BER packet at 64-QAM path A. Valid MIMO platforms only. Engineering use only. | ||||
| SbitErrors64QAMpathB | 1.3.6.1.4.1.161.19.3.2.2.135 | Counter64 | RO | |
scalar · Counter64 · read-only · current Number of bit errors received from BER packet at 64-QAM path B. Valid MIMO platforms only. Engineering use only. | ||||
| SbitErrors256QAMpathA | 1.3.6.1.4.1.161.19.3.2.2.136 | Counter64 | RO | |
scalar · Counter64 · read-only · current Number of bit errors received from BER packet at 256-QAM path A. Valid MIMO platforms only. Engineering use only. | ||||
| SbitErrors256QAMpathB | 1.3.6.1.4.1.161.19.3.2.2.137 | Counter64 | RO | |
scalar · Counter64 · read-only · current Number of bit errors received from BER packet at 256-QAM path B. Valid MIMO platforms only. Engineering use only. | ||||
| SbitsReceivedPerPathModulation | 1.3.6.1.4.1.161.19.3.2.2.138 | Counter64 | RO | |
scalar · Counter64 · read-only · current Number of bit received from BER. To calculate Bit Error Rate, take bit errors at a modulation and path and divide by this OID. To get combined BER add errors and divide by this multiplied by each path and modulation. i.e. MIMO QPSK combined BER = ((errors on path A) + (errors on path B))/(bits recieved per path modulation * 2) Valid MIMO platforms only. | ||||
| SbeaconsPercentReceived | 1.3.6.1.4.1.161.19.3.2.2.139 | INTEGER (0..100) | RO | |
scalar · INTEGER (0..100) · read-only · current The current percentage of beacons that the SM/BHS successfully received over the last 15 seconds. | ||||
| SmapsPercentReceived | 1.3.6.1.4.1.161.19.3.2.2.140 | INTEGER (0..100) | RO | |
scalar · INTEGER (0..100) · read-only · current PMP 450 only. The current percentage of scheduling maps that the SM successfully received over the last 15 seconds. | ||||
| SnatTslTableEntries | 1.3.6.1.4.1.161.19.3.2.2.141 | INTEGER | RO | |
scalar · INTEGER · read-only · current Number of Entries in NAT Translation Table. | ||||
| SmaxReceivePower | 1.3.6.1.4.1.161.19.3.2.2.142 | DisplayString | RO | |
scalar · DisplayString · read-only · current Maximum receive power level for this session. MIMO radios only. | ||||
| SbeaconsPercentMinReceived | 1.3.6.1.4.1.161.19.3.2.2.143 | INTEGER (0..100) | RO | |
scalar · INTEGER (0..100) · read-only · current The percentage of the least number of beacons that the SM/BHS successfully received in a 15 second window for the last 15 minutes. This will be updated only once in 15 minutes. For PMP SMs, this includes the Scheduling Uplink Map sent from the AP. | ||||
| SbeaconsPercentMaxReceived | 1.3.6.1.4.1.161.19.3.2.2.144 | INTEGER (0..100) | RO | |
scalar · INTEGER (0..100) · read-only · current The percentage of the maximum number of beacons that the SM/BHS successfully received in a 15 second window for the last 15 minutes. This will be updated only once in 15 minutes. For PMP SMs, this includes the Scheduling Uplink Map sent from the AP. | ||||
| SbeaconsPercentReceivedSnapshot | 1.3.6.1.4.1.161.19.3.2.2.145 | INTEGER (0..100) | RO | |
scalar · INTEGER (0..100) · read-only · current The percentage of beacons that the SM/BHS successfully received for the last 15 minutes. For PMP SMs, this includes the Scheduling Uplink Map sent from the AP. | ||||
| SsmSectorID | 1.3.6.1.4.1.161.19.3.2.2.146 | INTEGER | RO | |
scalar · INTEGER · read-only · current The current Sector ID of the Registered AP/BHM. A value of -1 is return when the device is not registered or AP/BHM does not support Sector ID. | ||||
| SscanCycleCount | 1.3.6.1.4.1.161.19.3.2.2.147 | Counter32 | RO | |
scalar · Counter32 · read-only · current The number of scan cycles. This increments after the SM completes scanning every configured frequency and channel bandwidth. | ||||
| SbridgeCbErrStatBridgeDropCount | 1.3.6.1.4.1.161.19.3.2.2.148 | Counter32 | RO | |
scalar · Counter32 · read-only · current Packet drop count for hosts with MAC address not in bridge table | ||||
| SspatialFrequency | 1.3.6.1.4.1.161.19.3.2.2.149 | INTEGER | RO | |
scalar · INTEGER · read-only · current The spatial frequency of registered SM. Spatial Frequency is the phase advance of the wavefront from one antenna column to the next caused by the angle at which the wavefront impinges on the array. It is represented in integer units, with 1024 equating to 360 degrees per column. A value of 2048 is used to signify a spatial frequency that is not yet known or otherwise invalid. A value of -1 is used to indicate that SM is not in session. Valid only for SMs that are capable of sounding and registered to MU-MIMO capable APs. General Error will result if sounding is not enabled on this device (either this device does not support sounding or the AP is not MU-MIMO capable). PMP only.
| ||||
| SisMumimoSector | 1.3.6.1.4.1.161.19.3.2.2.150 | INTEGER | RO | |
scalar · INTEGER · read-only · current Returns 1 if SM is registered to MU-MIMO capable AP. PMP only. | ||||
| SaverageEvmDownlinkPathA | 1.3.6.1.4.1.161.19.3.2.2.151 | INTEGER | RO | |
scalar · INTEGER · read-only · current The average downlink EVM expressed in dB for Path A.
| ||||
| SaverageEvmDownlinkPathB | 1.3.6.1.4.1.161.19.3.2.2.152 | INTEGER | RO | |
scalar · INTEGER · read-only · current The average downlink EVM expressed in dB for Path B.
| ||||
| ScombinedEvmDownlink | 1.3.6.1.4.1.161.19.3.2.2.153 | INTEGER | RO | |
scalar · INTEGER · read-only · current The combined downlink EVM expressed in dB for both paths. This value is scaled up by 10 (ie. -269 is equivalent to -26.9 dB).
| ||||
| SaverageEvmUplinkPathA | 1.3.6.1.4.1.161.19.3.2.2.154 | INTEGER | RO | |
scalar · INTEGER · read-only · current The average uplink EVM expressed in dB for Path A.
| ||||
| SaverageEvmUplinkPathB | 1.3.6.1.4.1.161.19.3.2.2.155 | INTEGER | RO | |
scalar · INTEGER · read-only · current The average uplink EVM expressed in dB for Path B.
| ||||
| ScombinedEvmUplink | 1.3.6.1.4.1.161.19.3.2.2.156 | INTEGER | RO | |
scalar · INTEGER · read-only · current The combined uplink EVM expressed in dB for both paths. This value is scaled up by 10 (ie. -269 is equivalent to -26.9 dB).
| ||||
| SintermediateModModeActive | 1.3.6.1.4.1.161.19.3.2.2.157 | INTEGER | RO | |
scalar · INTEGER · read-only · current Returns TRUE if Intermediate Modulation Modes are active on this link. Engineering Key only.
| ||||
| ScbrsStatus | 1.3.6.1.4.1.161.19.3.2.2.158 | INTEGER | RO | |
scalar · INTEGER · read-only · current Tells whether CBRS is enabled or disabled in AP/BHM.
| ||||
| SsmLUID | 1.3.6.1.4.1.161.19.3.2.2.159 | INTEGER | RO | |
scalar · INTEGER · read-only · current LUID or Logical User Identifier. This OID will return 0 if the SM is not registered. | ||||
| SregisteredApSwVersion | 1.3.6.1.4.1.161.19.3.2.2.160 | DisplayString | RO | |
scalar · DisplayString · read-only · current Registered AP's Software Version. | ||||
| SrfStatPowerAdjustmentCount | 1.3.6.1.4.1.161.19.3.2.2.161 | Counter32 | RO | |
scalar · Counter32 · read-only · current The number of times the AP or BHM has adjusted SM or BHS transmit power to match receieve target | ||||
| NwhispSmEvmStats | 1.3.6.1.4.1.161.19.3.2.2.162 | |||
| NwhispSmEvmStatsIntervalLow | 1.3.6.1.4.1.161.19.3.2.2.162.1 | |||
| SevmStatsLowAverageEvmDownlinkPathA | 1.3.6.1.4.1.161.19.3.2.2.162.1.1 | INTEGER | RO | |
scalar · INTEGER · read-only · current The average downlink EVM for 1 minute expressed in dB for Path A.
| ||||
| SevmStatsLowAverageEvmDownlinkPathB | 1.3.6.1.4.1.161.19.3.2.2.162.1.2 | INTEGER | RO | |
scalar · INTEGER · read-only · current The average downlink EVM for 1 minute expressed in dB for Path B.
| ||||
| SevmStatsLowCombinedAvgEvmDownlink | 1.3.6.1.4.1.161.19.3.2.2.162.1.3 | INTEGER | RO | |
scalar · INTEGER · read-only · current The combined downlink EVM for 1 minute expressed in dB for both paths. This value is scaled up by 10 (ie. -269 is equivalent to -26.9 dB).
| ||||
| SevmStatsLowAverageEvmUplinkPathA | 1.3.6.1.4.1.161.19.3.2.2.162.1.4 | INTEGER | RO | |
scalar · INTEGER · read-only · current The average uplink EVM for 1 minute expressed in dB for Path A.
| ||||
| SevmStatsLowAverageEvmUplinkPathB | 1.3.6.1.4.1.161.19.3.2.2.162.1.5 | INTEGER | RO | |
scalar · INTEGER · read-only · current The average uplink EVM for 1 minute expressed in dB for Path B.
| ||||
| SevmStatsLowCombinedAvgEvmUplink | 1.3.6.1.4.1.161.19.3.2.2.162.1.6 | INTEGER | RO | |
scalar · INTEGER · read-only · current The combined uplink EVM for 1 minute expressed in dB for both paths. This value is scaled up by 10 (ie. -269 is equivalent to -26.9 dB).
| ||||
| SevmStatsLowBestEvmDownlinkPathA | 1.3.6.1.4.1.161.19.3.2.2.162.1.7 | INTEGER | RO | |
scalar · INTEGER · read-only · current The best downlink EVM for 1 minute expressed in dB for Path A.
| ||||
| SevmStatsLowBestEvmDownlinkPathB | 1.3.6.1.4.1.161.19.3.2.2.162.1.8 | INTEGER | RO | |
scalar · INTEGER · read-only · current The best downlink EVM for 1 minute expressed in dB for Path B.
| ||||
| SevmStatsLowBestEvmUplinkPathA | 1.3.6.1.4.1.161.19.3.2.2.162.1.9 | INTEGER | RO | |
scalar · INTEGER · read-only · current The best uplink EVM for 1 minute expressed in dB for Path A.
| ||||
| SevmStatsLowBestEvmUplinkPathB | 1.3.6.1.4.1.161.19.3.2.2.162.1.10 | INTEGER | RO | |
scalar · INTEGER · read-only · current The best uplink EVM for 1 minute expressed in dB for Path B.
| ||||
| SevmStatsLowWorstEvmDownlinkPathA | 1.3.6.1.4.1.161.19.3.2.2.162.1.11 | INTEGER | RO | |
scalar · INTEGER · read-only · current The worst downlink EVM for 1 minute expressed in dB for Path A.
| ||||
| SevmStatsLowWorstEvmDownlinkPathB | 1.3.6.1.4.1.161.19.3.2.2.162.1.12 | INTEGER | RO | |
scalar · INTEGER · read-only · current The worst downlink EVM for 1 minute expressed in dB for Path B.
| ||||
| SevmStatsLowWorstEvmUplinkPathA | 1.3.6.1.4.1.161.19.3.2.2.162.1.13 | INTEGER | RO | |
scalar · INTEGER · read-only · current The worst uplink EVM for 1 minute expressed in dB for Path A.
| ||||
| SevmStatsLowWorstEvmUplinkPathB | 1.3.6.1.4.1.161.19.3.2.2.162.1.14 | INTEGER | RO | |
scalar · INTEGER · read-only · current The worst uplink EVM for 1 minute expressed in dB for Path B.
| ||||
| NwhispSmEvmStatsIntervalMid | 1.3.6.1.4.1.161.19.3.2.2.162.2 | |||
| SevmStatsMidAverageEvmDownlinkPathA | 1.3.6.1.4.1.161.19.3.2.2.162.2.1 | INTEGER | RO | |
scalar · INTEGER · read-only · current The average downlink EVM for 5 minutes expressed in dB for Path A.
| ||||
| SevmStatsMidAverageEvmDownlinkPathB | 1.3.6.1.4.1.161.19.3.2.2.162.2.2 | INTEGER | RO | |
scalar · INTEGER · read-only · current The average downlink EVM for 5 minutes expressed in dB for Path B.
| ||||
| SevmStatsMidCombinedAvgEvmDownlink | 1.3.6.1.4.1.161.19.3.2.2.162.2.3 | INTEGER | RO | |
scalar · INTEGER · read-only · current The combined downlink EVM for 5 minutes expressed in dB for both paths. This value is scaled up by 10 (ie. -269 is equivalent to -26.9 dB).
| ||||
| SevmStatsMidAverageEvmUplinkPathA | 1.3.6.1.4.1.161.19.3.2.2.162.2.4 | INTEGER | RO | |
scalar · INTEGER · read-only · current The average uplink EVM for 5 minutes expressed in dB for Path A.
| ||||
| SevmStatsMidAverageEvmUplinkPathB | 1.3.6.1.4.1.161.19.3.2.2.162.2.5 | INTEGER | RO | |
scalar · INTEGER · read-only · current The average uplink EVM for 5 minutes expressed in dB for Path B.
| ||||
| SevmStatsMidCombinedAvgEvmUplink | 1.3.6.1.4.1.161.19.3.2.2.162.2.6 | INTEGER | RO | |
scalar · INTEGER · read-only · current The combined average uplink EVM for 5 minutes expressed in dB for both paths. This value is scaled up by 10 (ie. -269 is equivalent to -26.9 dB).
| ||||
| SevmStatsMidBestEvmDownlinkPathA | 1.3.6.1.4.1.161.19.3.2.2.162.2.7 | INTEGER | RO | |
scalar · INTEGER · read-only · current The best downlink EVM for 5 minutes expressed in dB for Path A.
| ||||
| SevmStatsMidBestEvmDownlinkPathB | 1.3.6.1.4.1.161.19.3.2.2.162.2.8 | INTEGER | RO | |
scalar · INTEGER · read-only · current The best downlink EVM for 5 minutes expressed in dB for Path B.
| ||||
| SevmStatsMidBestEvmUplinkPathA | 1.3.6.1.4.1.161.19.3.2.2.162.2.9 | INTEGER | RO | |
scalar · INTEGER · read-only · current The best uplink EVM for 5 minutes expressed in dB for Path A.
| ||||
| SevmStatsMidBestEvmUplinkPathB | 1.3.6.1.4.1.161.19.3.2.2.162.2.10 | INTEGER | RO | |
scalar · INTEGER · read-only · current The best uplink EVM for 5 minutes expressed in dB for Path B.
| ||||
| SevmStatsMidWorstEvmDownlinkPathA | 1.3.6.1.4.1.161.19.3.2.2.162.2.11 | INTEGER | RO | |
scalar · INTEGER · read-only · current The worst downlink EVM for 5 minutes expressed in dB for Path A.
| ||||
| SevmStatsMidWorstEvmDownlinkPathB | 1.3.6.1.4.1.161.19.3.2.2.162.2.12 | INTEGER | RO | |
scalar · INTEGER · read-only · current The worst downlink EVM for 5 minutes expressed in dB for Path B.
| ||||
| SevmStatsMidWorstEvmUplinkPathA | 1.3.6.1.4.1.161.19.3.2.2.162.2.13 | INTEGER | RO | |
scalar · INTEGER · read-only · current The worst uplink EVM for 5 minutes expressed in dB for Path A.
| ||||
| SevmStatsMidWorstEvmUplinkPathB | 1.3.6.1.4.1.161.19.3.2.2.162.2.14 | INTEGER | RO | |
scalar · INTEGER · read-only · current The worst uplink EVM for 5 minutes expressed in dB for Path B.
| ||||
| NwhispSmEvmStatsIntervalHigh | 1.3.6.1.4.1.161.19.3.2.2.162.3 | |||
| SevmStatsHighAverageEvmDownlinkPathA | 1.3.6.1.4.1.161.19.3.2.2.162.3.1 | INTEGER | RO | |
scalar · INTEGER · read-only · current The average downlink EVM for 15 minutes expressed in dB for Path A.
| ||||
| SevmStatsHighAverageEvmDownlinkPathB | 1.3.6.1.4.1.161.19.3.2.2.162.3.2 | INTEGER | RO | |
scalar · INTEGER · read-only · current The average downlink EVM for 15 minutes expressed in dB for Path B.
| ||||
| SevmStatsHighCombinedAvgEvmDownlink | 1.3.6.1.4.1.161.19.3.2.2.162.3.3 | INTEGER | RO | |
scalar · INTEGER · read-only · current The combined average downlink EVM for 15 minutes expressed in dB for both paths. This value is scaled up by 10 (ie. -269 is equivalent to -26.9 dB).
| ||||
| SevmStatsHighAverageEvmUplinkPathA | 1.3.6.1.4.1.161.19.3.2.2.162.3.4 | INTEGER | RO | |
scalar · INTEGER · read-only · current The average uplink EVM for 15 minutes expressed in dB for Path A.
| ||||
| SevmStatsHighAverageEvmUplinkPathB | 1.3.6.1.4.1.161.19.3.2.2.162.3.5 | INTEGER | RO | |
scalar · INTEGER · read-only · current The average uplink EVM for 15 minutes expressed in dB for Path B.
| ||||
| SevmStatsHighCombinedAvgEvmUplink | 1.3.6.1.4.1.161.19.3.2.2.162.3.6 | INTEGER | RO | |
scalar · INTEGER · read-only · current The combined average uplink EVM for 15 minutes expressed in dB for both paths. This value is scaled up by 10 (ie. -269 is equivalent to -26.9 dB).
| ||||
| SevmStatsHighBestEvmDownlinkPathA | 1.3.6.1.4.1.161.19.3.2.2.162.3.7 | INTEGER | RO | |
scalar · INTEGER · read-only · current The best downlink EVM for 15 minutes expressed in dB for Path A.
| ||||
| SevmStatsHighBestEvmDownlinkPathB | 1.3.6.1.4.1.161.19.3.2.2.162.3.8 | INTEGER | RO | |
scalar · INTEGER · read-only · current The best downlink EVM for 15 minutes expressed in dB for Path B.
| ||||
| SevmStatsHighBestEvmUplinkPathA | 1.3.6.1.4.1.161.19.3.2.2.162.3.9 | INTEGER | RO | |
scalar · INTEGER · read-only · current The best uplink EVM for 15 minutes expressed in dB for Path A.
| ||||
| SevmStatsHighBestEvmUplinkPathB | 1.3.6.1.4.1.161.19.3.2.2.162.3.10 | INTEGER | RO | |
scalar · INTEGER · read-only · current The best uplink EVM for 15 minutes expressed in dB for Path B.
| ||||
| SevmStatsHighWorstEvmDownlinkPathA | 1.3.6.1.4.1.161.19.3.2.2.162.3.11 | INTEGER | RO | |
scalar · INTEGER · read-only · current The worst downlink EVM for 15 minutes expressed in dB for Path A.
| ||||
| SevmStatsHighWorstEvmDownlinkPathB | 1.3.6.1.4.1.161.19.3.2.2.162.3.12 | INTEGER | RO | |
scalar · INTEGER · read-only · current The worst downlink EVM for 15 minutes expressed in dB for Path B.
| ||||
| SevmStatsHighWorstEvmUplinkPathA | 1.3.6.1.4.1.161.19.3.2.2.162.3.13 | INTEGER | RO | |
scalar · INTEGER · read-only · current The worst uplink EVM for 15 minutes expressed in dB for Path A.
| ||||
| SevmStatsHighWorstEvmUplinkPathB | 1.3.6.1.4.1.161.19.3.2.2.162.3.14 | INTEGER | RO | |
scalar · INTEGER · read-only · current The worst uplink EVM for 15 minutes expressed in dB for Path B.
| ||||
| NwhispSmGroups | 1.3.6.1.4.1.161.19.3.2.3 | |||
| GwhispSmConfigGroup | 1.3.6.1.4.1.161.19.3.2.3.1 | |||
group · current Canopy Subscriber Module configuration group.
| ||||
| GwhispSmStatusGroup | 1.3.6.1.4.1.161.19.3.2.3.2 | |||
group · current Canopy Subscriber Module status group.
| ||||
| GwhispSmNotifGroup | 1.3.6.1.4.1.161.19.3.2.3.3 | |||
group · current WHiSP SMs notification group. | ||||
| GwhispMappingTableGroup | 1.3.6.1.4.1.161.19.3.2.3.4 | |||
group · current Canopy SM NAT port mapping Table group.
| ||||
| GwhispPropSchedulerConfigGroup | 1.3.6.1.4.1.161.19.3.2.3.5 | |||
group · current Canopy SM Proportional Scheduler Config group. | ||||
| NwhispSmEvent | 1.3.6.1.4.1.161.19.3.2.4 | |||
| NwhispSmDfsEvent | 1.3.6.1.4.1.161.19.3.2.4.1 | |||
| !whispRadarDetected | 1.3.6.1.4.1.161.19.3.2.4.1.1 | |||
| !whispRadarEnd | 1.3.6.1.4.1.161.19.3.2.4.1.2 | |||
| NwhispSmSpAnEvent | 1.3.6.1.4.1.161.19.3.2.4.2 | |||
| !enterSpectrumAnalysis | 1.3.6.1.4.1.161.19.3.2.4.2.1 | |||
notification · current Entering spectrum analysis. physAddress - MAC address of the SM
| ||||
| !availableSpectrumAnalysis | 1.3.6.1.4.1.161.19.3.2.4.2.2 | |||
notification · current Spectrum analysis is complete, SM is re-registered with AP and results are available. physAddress - MAC address of the SM
| ||||
| NwhispSmDHCPClientEvent | 1.3.6.1.4.1.161.19.3.2.4.3 | |||
| !smNatWanDHCPClientEvent | 1.3.6.1.4.1.161.19.3.2.4.3.1 | |||
notification · current NAT WAN DHCP Client has received a new address via DHCP.
| ||||
| !smNatRFPubDHCPClientEvent | 1.3.6.1.4.1.161.19.3.2.4.3.2 | |||
notification · current NAT RF Public DHCP Client has received a new address via DHCP.
| ||||
| TwhispMappingTable | 1.3.6.1.4.1.161.19.3.2.5 | NA | ||
table · not-accessible · current NAT port mapping information table. | ||||
| RwhispMappingEntry | 1.3.6.1.4.1.161.19.3.2.5.1 | NA | ||
| CtableIndex | 1.3.6.1.4.1.161.19.3.2.5.1.1 | INTEGER (1..2147483647) | RO | |
column · INTEGER (1..2147483647) · read-only · current User information table index. | ||||
| Cprotocol | 1.3.6.1.4.1.161.19.3.2.5.1.2 | INTEGER | RO | |
column · INTEGER · read-only · current Protocol type: 0:both UDP and TCP, 1:UDP, 2:TCP. | ||||
| Cport | 1.3.6.1.4.1.161.19.3.2.5.1.3 | INTEGER | RO | |
column · INTEGER · read-only · current Application port number. e.g. 23=telnet, 21=ftp etc. Should be a positive integer. | ||||
| ClocalIp | 1.3.6.1.4.1.161.19.3.2.5.1.4 | IpAddress | RO | |
column · IpAddress · read-only · current IP of local host to which the incoming packet mapped to an application should be forwarded. | ||||
| CextPort | 1.3.6.1.4.1.161.19.3.2.5.1.5 | INTEGER | RO | |
column · INTEGER · read-only · current External port of the incoming packet mapped to an application should be forwarded. | ||||
| TwhispSmTranslationTable | 1.3.6.1.4.1.161.19.3.2.6 | NA | ||
table · not-accessible · current Translation Table. | ||||
| RwhispSmTranslationTableEntry | 1.3.6.1.4.1.161.19.3.2.6.1 | NA | ||
| CwhispTranslationTableIndex | 1.3.6.1.4.1.161.19.3.2.6.1.1 | INTEGER (1..127) | RO | |
column · INTEGER (1..127) · read-only · current Index into translation table. | ||||
| CwhispTranslationTableMacAddr | 1.3.6.1.4.1.161.19.3.2.6.1.2 | MacAddress | RO | |
column · MacAddress · read-only · current MAC Address of the registered entity. | ||||
| CwhispTranslationTableIpAddr | 1.3.6.1.4.1.161.19.3.2.6.1.3 | IpAddress | RO | |
column · IpAddress · read-only · current Ip Address of the registered entity. | ||||
| CwhispTranslationTableAge | 1.3.6.1.4.1.161.19.3.2.6.1.4 | Counter32 | RO | |
column · Counter32 · read-only · current Age of the registered entity. | ||||
| NwhispSmSecurity | 1.3.6.1.4.1.161.19.3.2.7 | |||
| TcertTable | 1.3.6.1.4.1.161.19.3.2.7.1 | NA | ||
table · not-accessible · current The table of CA Certificates on SM. | ||||
| RcertEntry | 1.3.6.1.4.1.161.19.3.2.7.1.1 | NA | ||
| CcertIndex | 1.3.6.1.4.1.161.19.3.2.7.1.1.1 | INTEGER (1..2) | RO | |
column · INTEGER (1..2) · read-only · current User information table index. | ||||
| Ccert | 1.3.6.1.4.1.161.19.3.2.7.1.1.2 | INTEGER | RO | |
column · INTEGER · read-only · current 0: Inactive 1: Active
| ||||
| Caction | 1.3.6.1.4.1.161.19.3.2.7.1.1.3 | INTEGER | RW | |
column · INTEGER · read-write · current 0: No Operation 1: Delete Certificate
| ||||
| CcertificateDN | 1.3.6.1.4.1.161.19.3.2.7.1.1.4 | DisplayString | RO | |
column · DisplayString · read-only · current Distinguished Name of Certificate 2 | ||||
| SnumAuthCerts | 1.3.6.1.4.1.161.19.3.2.7.2 | INTEGER | RO | |
scalar · INTEGER · read-only · current can have a max value of 4. 2 for User Authenticaion server and 2 for SM Authentication server. | ||||
| SauthenticationEnforce | 1.3.6.1.4.1.161.19.3.2.7.3 | INTEGER | RW | |
scalar · INTEGER · read-write · current enforce SM to register with specifed Auth Enabled AP
| ||||
| Sphase1 | 1.3.6.1.4.1.161.19.3.2.7.4 | INTEGER | RW | |
scalar · INTEGER · read-write · current Select the outer method for EAP Authentication. Note: PEAP is not supported for MPC860 platform.
| ||||
| Sphase2 | 1.3.6.1.4.1.161.19.3.2.7.5 | INTEGER | RW | |
scalar · INTEGER · read-write · current Select the outer method for EAP Authentication
| ||||
| SauthOuterId | 1.3.6.1.4.1.161.19.3.2.7.6 | OCTET STRING (SIZE (0..253)) | RW | |
scalar · OCTET STRING (SIZE (0..253)) · read-write · current EAP Peer Username | ||||
| SauthPassword | 1.3.6.1.4.1.161.19.3.2.7.7 | DisplayString | RW | |
scalar · DisplayString · read-write · current EAP Peer password | ||||
| SauthUsername | 1.3.6.1.4.1.161.19.3.2.7.8 | DisplayString | RW | |
scalar · DisplayString · read-write · current EAP Peer Identity | ||||
| SuseRealm | 1.3.6.1.4.1.161.19.3.2.7.9 | INTEGER | RW | |
scalar · INTEGER · read-write · current Enable or disable the use of realm option.
| ||||
| Srealm | 1.3.6.1.4.1.161.19.3.2.7.10 | DisplayString | RW | |
scalar · DisplayString · read-write · current EAP Peer Realm | ||||
| NwhispSmControls | 1.3.6.1.4.1.161.19.3.2.8 | |||
| SclearLinkStats | 1.3.6.1.4.1.161.19.3.2.8.1 | INTEGER | RW | |
scalar · INTEGER · read-write · current Setting this to a nonzero value will clear the link stats. | ||||
| Srescan | 1.3.6.1.4.1.161.19.3.2.8.2 | INTEGER | RW | |
scalar · INTEGER · read-write · current Setting this to a nonzero value will start the rescan. Warning: If currently connected, this will cause the SM/BHS to drop session | ||||
| SapEvalControl | 1.3.6.1.4.1.161.19.3.2.8.3 | INTEGER | RW | |
scalar · INTEGER · read-write · current Setting this to 0 will clear the AP Evaluation Data. | ||||
| TwhispSmColorCodeTable | 1.3.6.1.4.1.161.19.3.2.9 | NA | ||
table · not-accessible · current Additional color code Table. | ||||
| RwhispSmColorCodeEntry | 1.3.6.1.4.1.161.19.3.2.9.1 | NA | ||
| CentryColorCode | 1.3.6.1.4.1.161.19.3.2.9.1.1 | INTEGER (0..254) | RO | |
column · INTEGER (0..254) · read-only · current color code. | ||||
| CentryColorCodePriority | 1.3.6.1.4.1.161.19.3.2.9.1.2 | INTEGER | RO | |
column · INTEGER · read-only · current color code priority.
| ||||
| TwhispSmAPEvalTable | 1.3.6.1.4.1.161.19.3.2.10 | NA | ||
table · not-accessible · current AP Eval List. | ||||
| RwhispSmAPEvalEntry | 1.3.6.1.4.1.161.19.3.2.10.1 | NA | ||
| CevalIndex | 1.3.6.1.4.1.161.19.3.2.10.1.1 | INTEGER (1..16) | RO | |
column · INTEGER (1..16) · read-only · current Index of the radio seen in the scan | ||||
| CevalFrequency | 1.3.6.1.4.1.161.19.3.2.10.1.2 | INTEGER | RO | |
column · INTEGER · read-only · current Transmit Frequency in kHz | ||||
| CevalChannelBandwidth | 1.3.6.1.4.1.161.19.3.2.10.1.3 | INTEGER | RO | |
column · INTEGER · read-only · current Channel Bandwidth
| ||||
| CevalCyclicPrefix | 1.3.6.1.4.1.161.19.3.2.10.1.4 | INTEGER | RO | |
column · INTEGER · read-only · current Cyclic Prefix value, for OFDM Radios only.
| ||||
| CevalESN | 1.3.6.1.4.1.161.19.3.2.10.1.5 | PhysAddress | RO | |
column · PhysAddress · read-only · current Radio ESN | ||||
| CevalRegion | 1.3.6.1.4.1.161.19.3.2.10.1.6 | DisplayString | RO | |
column · DisplayString · read-only · current Region | ||||
| CevalBeaconReceivePowerCombined | 1.3.6.1.4.1.161.19.3.2.10.1.7 | INTEGER | RO | |
column · INTEGER · read-only · current Beacon Receive Power Combined in dBm(rounded to nearest integer) | ||||
| CevalBeaconReceivePowerH | 1.3.6.1.4.1.161.19.3.2.10.1.8 | INTEGER | RO | |
column · INTEGER · read-only · current Beacon Receive Power in dBm(rounded to nearest integer) for Path H(MIMO Radios only) | ||||
| CevalBeaconReceivePowerV | 1.3.6.1.4.1.161.19.3.2.10.1.9 | INTEGER | RO | |
column · INTEGER · read-only · current Beacon Receive Power in dBm(rounded to nearest integer) for Path V(MIMO Radios only) | ||||
| CevalFECEnable | 1.3.6.1.4.1.161.19.3.2.10.1.10 | INTEGER | RO | |
column · INTEGER · read-only · current Forward Error Correction Enabled Status. Note, this is always enabled on 450 and forward.
| ||||
| CevalType | 1.3.6.1.4.1.161.19.3.2.10.1.11 | INTEGER | RO | |
column · INTEGER · read-only · current Radio Type (Point-to-Point or Multipoint)
| ||||
| CevalAvail | 1.3.6.1.4.1.161.19.3.2.10.1.12 | INTEGER | RO | |
column · INTEGER · read-only · current Returns True if seen on the previous SM's scan
| ||||
| CevalAge | 1.3.6.1.4.1.161.19.3.2.10.1.13 | INTEGER | RO | |
column · INTEGER · read-only · current Number of minutes since index was last seen | ||||
| CevalLockout | 1.3.6.1.4.1.161.19.3.2.10.1.14 | INTEGER | RO | |
column · INTEGER · read-only · current Number of minutes radio is currently locked out | ||||
| CevalRegFail | 1.3.6.1.4.1.161.19.3.2.10.1.15 | INTEGER | RO | |
column · INTEGER · read-only · current Registration Fail Count | ||||
| CevalRange | 1.3.6.1.4.1.161.19.3.2.10.1.16 | INTEGER | RO | |
column · INTEGER · read-only · current Range in feet | ||||
| CevalMaxRange | 1.3.6.1.4.1.161.19.3.2.10.1.17 | INTEGER | RO | |
column · INTEGER · read-only · current Max Range is in miles | ||||
| CevalTxBER | 1.3.6.1.4.1.161.19.3.2.10.1.18 | INTEGER | RO | |
column · INTEGER · read-only · current Radio is transmitting Bit Error Rate symbol or not Note: This is always enabled on 450 and forward
| ||||
| CevalEBCast | 1.3.6.1.4.1.161.19.3.2.10.1.19 | INTEGER | RO | |
column · INTEGER · read-only · current Broadcast Encryption status
| ||||
| CevalSessionCount | 1.3.6.1.4.1.161.19.3.2.10.1.20 | INTEGER | RO | |
column · INTEGER · read-only · current Session Count | ||||
| CevalNoLuid | 1.3.6.1.4.1.161.19.3.2.10.1.21 | INTEGER | RO | |
column · INTEGER · read-only · current Number of times the registration request has been rejected due to No Luid | ||||
| CevalOutOfRange | 1.3.6.1.4.1.161.19.3.2.10.1.22 | INTEGER | RO | |
column · INTEGER · read-only · current Number of times the registration request has been rejected due to out of range | ||||
| CevalAuthFail | 1.3.6.1.4.1.161.19.3.2.10.1.23 | INTEGER | RO | |
column · INTEGER · read-only · current Number of times the registration request has been rejected due to authentication failure | ||||
| CevalEncryptFail | 1.3.6.1.4.1.161.19.3.2.10.1.24 | INTEGER | RO | |
column · INTEGER · read-only · current Number of times the registration request has been rejected due to encrypt fail | ||||
| CevalReScanReq | 1.3.6.1.4.1.161.19.3.2.10.1.25 | INTEGER | RO | |
column · INTEGER · read-only · current Rescan request count | ||||
| CevalLimitReached | 1.3.6.1.4.1.161.19.3.2.10.1.26 | INTEGER | RO | |
column · INTEGER · read-only · current Number of times failed when trying to register with an limited AP maxed out | ||||
| CevalNoVCs | 1.3.6.1.4.1.161.19.3.2.10.1.27 | INTEGER | RO | |
column · INTEGER · read-only · current Number of times the registration request has been rejected due to No VCs | ||||
| CevalVCReserveFail | 1.3.6.1.4.1.161.19.3.2.10.1.28 | INTEGER | RO | |
column · INTEGER · read-only · current Number of times the registration request has been rejected due to VC reserve fail | ||||
| CevalVCActFail | 1.3.6.1.4.1.161.19.3.2.10.1.29 | INTEGER | RO | |
column · INTEGER · read-only · current Number of times the registration request has been rejected due to VC activate fail | ||||
| CevalTxPower | 1.3.6.1.4.1.161.19.3.2.10.1.30 | INTEGER | RO | |
column · INTEGER · read-only · current Transmit Power in dBm | ||||
| CevalReceiveTargetLevel | 1.3.6.1.4.1.161.19.3.2.10.1.31 | INTEGER | RO | |
column · INTEGER · read-only · current Receive Target Level(in dBm)(PMP only) | ||||
| CevalColorCode | 1.3.6.1.4.1.161.19.3.2.10.1.32 | INTEGER | RO | |
column · INTEGER · read-only · current Color Code | ||||
| CevalBeaconVersion | 1.3.6.1.4.1.161.19.3.2.10.1.33 | INTEGER | RO | |
column · INTEGER · read-only · current Beacon Version | ||||
| CevalSectorUserCount | 1.3.6.1.4.1.161.19.3.2.10.1.34 | INTEGER | RO | |
column · INTEGER · read-only · current Sector User Count(AP only) | ||||
| CevalSyncSrc | 1.3.6.1.4.1.161.19.3.2.10.1.35 | INTEGER | RO | |
column · INTEGER · read-only · current Sync Source(PMP only)
| ||||
| CevalNumULSlots | 1.3.6.1.4.1.161.19.3.2.10.1.36 | INTEGER | RO | |
column · INTEGER · read-only · current Number of uplink slots | ||||
| CevalNumDLSlots | 1.3.6.1.4.1.161.19.3.2.10.1.37 | INTEGER | RO | |
column · INTEGER · read-only · current Number of downlink slots | ||||
| CevalNumULContSlots | 1.3.6.1.4.1.161.19.3.2.10.1.38 | INTEGER | RO | |
column · INTEGER · read-only · current Number of uplink contention slots(PMP only) | ||||
| CevalICC | 1.3.6.1.4.1.161.19.3.2.10.1.39 | INTEGER | RO | |
column · INTEGER · read-only · current Instalaton Color Code(PMP only)
| ||||
| CevalAuthentication | 1.3.6.1.4.1.161.19.3.2.10.1.40 | INTEGER | RO | |
column · INTEGER · read-only · current Authentication Setting(PMP only)
| ||||
| CevalSMPPPoE | 1.3.6.1.4.1.161.19.3.2.10.1.41 | INTEGER | RO | |
column · INTEGER · read-only · current SM PPPoE status(PMP only)
| ||||
| CevalPToPVLAN | 1.3.6.1.4.1.161.19.3.2.10.1.42 | INTEGER | RO | |
column · INTEGER · read-only · current PToP VLAN
| ||||
| CevalFramePeriod | 1.3.6.1.4.1.161.19.3.2.10.1.43 | INTEGER | RO | |
column · INTEGER · read-only · current Frame Period
| ||||
| CevalAirDelayNs | 1.3.6.1.4.1.161.19.3.2.10.1.44 | INTEGER | RO | |
column · INTEGER · read-only · current Air Delay in ns. A value of -1 indicates air delay is not available. | ||||
| CevalAirDelayString | 1.3.6.1.4.1.161.19.3.2.10.1.45 | DisplayString | RO | |
column · DisplayString · read-only · current Air Delay string (miles or km). | ||||
| CevalLastKnownPrimaryAP | 1.3.6.1.4.1.161.19.3.2.10.1.46 | INTEGER | RO | |
column · INTEGER · read-only · current Tells if this AP is Last known Primary Color code AP, SM registered with.
| ||||
| CevalCbrsFail | 1.3.6.1.4.1.161.19.3.2.10.1.47 | INTEGER | RO | |
column · INTEGER · read-only · current Number of times the registration request has been rejected due to CBRS failure | ||||
| CevalTotalActiveBandwdith | 1.3.6.1.4.1.161.19.3.2.10.1.48 | INTEGER | RO | |
column · INTEGER · read-only · current Total Active Bandwidth advertised by AP in MHz | ||||
| CevalAntennaGain | 1.3.6.1.4.1.161.19.3.2.10.1.49 | INTEGER | RO | |
column · INTEGER · read-only · current Antenna Gain of the AP in dBi Available if AP is on version 23.0 or later. Unavailable when AP is 450m. | ||||
| NwhispSmRFStatus | 1.3.6.1.4.1.161.19.3.2.11 | |||
| TsmCarrierInfo | 1.3.6.1.4.1.161.19.3.2.11.1 | NA | ||
table · not-accessible · current Canopy V SM Carrier Information table | ||||
| RsmCarrierInfoEntry | 1.3.6.1.4.1.161.19.3.2.11.1.1 | NA | ||
| CsmCarrierTableIdx | 1.3.6.1.4.1.161.19.3.2.11.1.1.1 | INTEGER (1..2) | RO | |
column · INTEGER (1..2) · read-only · current Carrier Information Table Index | ||||
| CsmCarrierStatus | 1.3.6.1.4.1.161.19.3.2.11.1.1.2 | INTEGER | RO | |
column · INTEGER · read-only · current Carrier Status 1-Active 0-Inactive
| ||||
| CsmCarrierBand | 1.3.6.1.4.1.161.19.3.2.11.1.1.3 | INTEGER | RO | |
column · INTEGER · read-only · current Active Carrier's Band
| ||||
| CsmCarrierAggregateBw | 1.3.6.1.4.1.161.19.3.2.11.1.1.4 | INTEGER | RO | |
column · INTEGER · read-only · current Carrier Aggregate Bandwidth in MHz
| ||||
| CsmCarrierTxPwr | 1.3.6.1.4.1.161.19.3.2.11.1.1.5 | INTEGER | RO | |
column · INTEGER · read-only · current Carrier Specific Transmit Power in dBm
| ||||
| CsmCarrierRxPower | 1.3.6.1.4.1.161.19.3.2.11.1.1.6 | INTEGER | RO | |
column · INTEGER · read-only · current Carrier's Specific Receive Power in dBm. The received power is combined across vertical and horizontal paths per component carrier and averaged across component carriers.
| ||||
| CsmCarrierEIRP | 1.3.6.1.4.1.161.19.3.2.11.1.1.7 | INTEGER | RO | |
column · INTEGER · read-only · current Carrier EIRP in dBm
| ||||
| TsmComponentCarrierInfo | 1.3.6.1.4.1.161.19.3.2.11.2 | NA | ||
table · not-accessible · current Canopy V SM Component Carrier Information table | ||||
| RsmComponentCarrierInfoEntry | 1.3.6.1.4.1.161.19.3.2.11.2.1 | NA | ||
row · not-accessible · current Canopy V SM Component Carrier Information table entry
| ||||
| CsmCCTableIdx | 1.3.6.1.4.1.161.19.3.2.11.2.1.1 | INTEGER (1..4) | RO | |
column · INTEGER (1..4) · read-only · current Index to the Canopy V Component Carrier Information Table | ||||
| CsmCCStatus | 1.3.6.1.4.1.161.19.3.2.11.2.1.2 | INTEGER | RO | |
column · INTEGER · read-only · current SM Component Carrier Status 1-Active 0-Inactive
| ||||
| CsmCCCarrierAssignment | 1.3.6.1.4.1.161.19.3.2.11.2.1.3 | INTEGER | RO | |
column · INTEGER · read-only · current Carrier Assignment for the Component Carrier | ||||
| CsmCCChannelFreq | 1.3.6.1.4.1.161.19.3.2.11.2.1.4 | INTEGER | RO | |
column · INTEGER · read-only · current Component Carrier Specific Channel Frequency Value in kHz
| ||||
| CsmCCChannelBW | 1.3.6.1.4.1.161.19.3.2.11.2.1.5 | INTEGER | RO | |
column · INTEGER · read-only · current Channel Bandwidth in MHz
| ||||
| CsmCCTxPwr | 1.3.6.1.4.1.161.19.3.2.11.2.1.6 | INTEGER | RO | |
column · INTEGER · read-only · current The Component Carrier Transmit Power in dBm
| ||||
| CsmCCULModRate | 1.3.6.1.4.1.161.19.3.2.11.2.1.7 | DisplayString | RO | |
column · DisplayString · read-only · current Component Carrier Uplink Modulation Rate | ||||
| CsmCCSignalStrengthRatio | 1.3.6.1.4.1.161.19.3.2.11.2.1.8 | DisplayString | RO | |
column · DisplayString · read-only · current Component Carrier's Signal Strength Ratio in dBm
| ||||
| CsmCCRxPower | 1.3.6.1.4.1.161.19.3.2.11.2.1.9 | INTEGER | RO | |
column · INTEGER · read-only · current Component Carrier Receive Power in dBm
| ||||
| CsmCCBER | 1.3.6.1.4.1.161.19.3.2.11.2.1.10 | DisplayString | RO | |
column · DisplayString · read-only · current Component Carrier Bit Error Rate | ||||
| CsmCCAvgBERQPSKPathA | 1.3.6.1.4.1.161.19.3.2.11.2.1.11 | DisplayString | RO | |
column · DisplayString · read-only · current Average number of bit errors received from BER packet at QPSK pathA. | ||||
| CsmCCAvgBERQPSKPathB | 1.3.6.1.4.1.161.19.3.2.11.2.1.12 | DisplayString | RO | |
column · DisplayString · read-only · current Average number of bit errors received from BER packet at QPSK pathB. | ||||
| CsmCCRssiHorizontal | 1.3.6.1.4.1.161.19.3.2.11.2.1.13 | DisplayString | RO | |
column · DisplayString · read-only · current Component Carrier receive power level of the horizontal antenna in dBm. | ||||
| CsmCCRssiVertical | 1.3.6.1.4.1.161.19.3.2.11.2.1.14 | DisplayString | RO | |
column · DisplayString · read-only · current Component Carrier receive power level of the vertical antenna in dBm. | ||||
Traps / Notifications
- availableSpectrumAnalysis
1.3.6.1.4.1.161.19.3.2.4.2.2 - enterSpectrumAnalysis
1.3.6.1.4.1.161.19.3.2.4.2.1 - smNatRFPubDHCPClientEvent
1.3.6.1.4.1.161.19.3.2.4.3.2 - smNatWanDHCPClientEvent
1.3.6.1.4.1.161.19.3.2.4.3.1 - whispRadarDetected
1.3.6.1.4.1.161.19.3.2.4.1.1 - whispRadarEnd
1.3.6.1.4.1.161.19.3.2.4.1.2