BIANCA-BRICK-MIB
BinTec Communications GmbHMIB module for vendor specific box definitions.
Note: bibo stands for BinTec box stemming from the times where
the company was still called BinTec.snmptranslate -m BIANCA-BRICK-MIB -Tpsnmpwalk -v2c -c <community> -m BIANCA-BRICK-MIB <host> 1.3.6.1.4.1.272.250Imports
| BINTEC-MIB | Date, HexValue, bibo, bintec, sys |
|---|---|
| SNMPv2-CONF | MODULE-COMPLIANCE, NOTIFICATION-GROUP |
| SNMPv2-MIB | sysDescr, sysName |
| SNMPv2-SMI | Bits, Counter32, Counter64, Gauge32, Integer32, IpAddress, MODULE-IDENTITY, MibIdentifier, NOTIFICATION-TYPE, OBJECT-IDENTITY, OBJECT-TYPE, TRAP-TYPE, TimeTicks, Unsigned32, enterprises, iso, mib-2 |
| SNMPv2-TC | DisplayString, PhysAddress, TEXTUAL-CONVENTION, TimeStamp, TruthValue |
OID tree
| Name | OID | Type | Access | Status | Example | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Nadmin | 1.3.6.1.4.1.272.4.1 | ||||||||||||
| SbiboAdmIpAddr | 1.3.6.1.4.1.272.4.1.8 | IpAddress | RW | ||||||||||
scalar · IpAddress · read-write · current Local IP address. If this object is set, it's value will be used as the source address for all IP packets that are sent. Otherwise, the IP address used will be retrieved from the ipRouteTable, for the interface the IP packet is to be transmitted over. | |||||||||||||
| TbiboAdmTrapHostTable | 1.3.6.1.4.1.272.4.1.10 | NA | |||||||||||
table · not-accessible · current The biboAdmTrapHostTable defines where traps are sent (i.e., which hosts). If the table is empty traps are broadcasted. Creating entries: Entries are added by assigning an IP address value to the biboAdmTrapHostAddr field. Deleting entries: Entries can be removed by assigning ing the respective biboAdmTrapHostStatus field to 'delete'. | |||||||||||||
| RbiboAdmTrapHostEntry | 1.3.6.1.4.1.272.4.1.10.1 | NA | |||||||||||
row · not-accessible · current
| |||||||||||||
| CbiboAdmTrapHostAddr | 1.3.6.1.4.1.272.4.1.10.1.1 | IpAddress | RW | ||||||||||
column · IpAddress · read-write · current Ip-Address where traps are sent. | |||||||||||||
| CbiboAdmTrapHostStatus | 1.3.6.1.4.1.272.4.1.10.1.2 | INTEGER | RW | ||||||||||
column · INTEGER · read-write · current Status is always valid, and set to delete only to discard the whole entry.
| |||||||||||||
| SbiboAdmSyslogMaxEntries | 1.3.6.1.4.1.272.4.1.11 | INTEGER | RW | ||||||||||
scalar · INTEGER · read-write · current Maximum Number of syslog messages stored in memory. | |||||||||||||
| TbiboAdmSyslogTable | 1.3.6.1.4.1.272.4.1.12 | NA | |||||||||||
table · not-accessible · current The biboAdmSyslogTable keeps track of syslog messages received. The size of the table (number of entries), is limited by the value of biboAdmSyslogMaxEntries. The columns specify attributes for each message generated. As this information only reports events on the system, all fields are read-only. Creating entries: Entries can only be created by the system and are made each time a syslog message is generated. Deleting entries: Entries are removed by the system once the size limit (biboAdmSyslogMaxEntries) is reached. | |||||||||||||
| RbiboAdmSyslogEntry | 1.3.6.1.4.1.272.4.1.12.1 | NA | |||||||||||
row · not-accessible · current | |||||||||||||
| CbiboAdmSyslogTimeStamp | 1.3.6.1.4.1.272.4.1.12.1.1 | Date | RO | ||||||||||
column · Date · read-only · current Time message was generated. | |||||||||||||
| CbiboAdmSyslogLevel | 1.3.6.1.4.1.272.4.1.12.1.2 | INTEGER | RO | ||||||||||
column · INTEGER · read-only · current Level of syslog message.
| |||||||||||||
| CbiboAdmSyslogMessage | 1.3.6.1.4.1.272.4.1.12.1.4 | DisplayString | RO | ||||||||||
column · DisplayString · read-only · current The text of the syslog message. | |||||||||||||
| CbiboAdmSyslogSubject | 1.3.6.1.4.1.272.4.1.12.1.5 | INTEGER | RO | ||||||||||
column · INTEGER · read-only · current Subject of the syslog message.
| |||||||||||||
| TbiboAdmLogHostTable | 1.3.6.1.4.1.272.4.1.13 | NA | |||||||||||
table · not-accessible · current The biboAdmLogHostTable lists hosts which are to receive syslog messages. This table also defines which types and levels of messages to send. Creating entries: Entries are created by setting a IP address to biboAdmLogHostAddr. Deleting entries: Entries are removed by setting the appropriate biboAdmLogHostLevel field to 'delete'. | |||||||||||||
| RbiboAdmLogHostEntry | 1.3.6.1.4.1.272.4.1.13.1 | NA | |||||||||||
row · not-accessible · current
| |||||||||||||
| CbiboAdmLogHostAddr | 1.3.6.1.4.1.272.4.1.13.1.1 | IpAddress | RW | ||||||||||
column · IpAddress · read-write · current Ip-Address where syslog messages are sent. If the facility is set to memory or console, this field is not used. | |||||||||||||
| CbiboAdmLogHostLevel | 1.3.6.1.4.1.272.4.1.13.1.2 | INTEGER | RW | ||||||||||
column · INTEGER · read-write · current Priorities lower or equal this level are sent to loghost. The delete priority is used to discard the whole entry.
| |||||||||||||
| CbiboAdmLogHostFacility | 1.3.6.1.4.1.272.4.1.13.1.4 | INTEGER | RW | ||||||||||
column · INTEGER · read-write · current The facility used for the syslog messages being generated.
| |||||||||||||
| CbiboAdmLogHostType | 1.3.6.1.4.1.272.4.1.13.1.5 | INTEGER | RW | ||||||||||
column · INTEGER · read-write · current The subject of the messages that are to be generated. system means all subjects except accounting, all means all subjects.
| |||||||||||||
| CbiboAdmLogHostTimestamp | 1.3.6.1.4.1.272.4.1.13.1.6 | INTEGER | RW | ||||||||||
column · INTEGER · read-write · current This object describes the format of the timestamp. none(1) = no timestamp, time(2) = only time is printed, all(3) = date and time is printed.
| |||||||||||||
| CbiboAdmLogHostMethod | 1.3.6.1.4.1.272.4.1.13.1.7 | INTEGER | RW | ||||||||||
column · INTEGER · read-write · current This object provides protocol for sending syslog messages: udp(1) = udp tcp(2) = tcp
| |||||||||||||
| TbiboAdmConfigTable | 1.3.6.1.4.1.272.4.1.14 | NA | |||||||||||
table · not-accessible · current The biboAdmConfigTable is used for assigning parameters for managing configuration files. Creating entries: Entries are added to this table by assigning a value to the biboAdmConfigCmd object. (i.e., The intermediate result of executing, cmd=save, creates an entry to this table.). Deleting entries: Entries can only be removed by the system and is done only after the requested action has been performed (i.e. Once the cmd=save action is complete.). | |||||||||||||
| RbiboAdmConfigEntry | 1.3.6.1.4.1.272.4.1.14.1 | NA | |||||||||||
row · not-accessible · current
| |||||||||||||
| CbiboAdmConfigCmd | 1.3.6.1.4.1.272.4.1.14.1.1 | INTEGER | RW | ||||||||||
column · INTEGER · read-write · current Command for configuration handling. Possible values are :
save(1) = save configuration (to FLASH)
load(2) = load configuration (from FLASH)
put(3) = write configuration (via TFTP)
get(4) = read configuration (via TFTP)
state(5) = write complete configuration (via TFTP)
delete(6) = delete configuration (within FLASH)
move(7) = move configuration (within FLASH)
copy(8) = copy configuration (within FLASH)
reboot(9) = reboot the system
reorg(10) = reorganizes the flash
unload(11) = remove loaded configuration (from RAM)
put_all(12) = write configuration (via TFTP),
include not accessible variables
get_all(13) = read configuration (via TFTP),
including not accessible variables
load_keep_certs(14) = load configuration (from FLASH),
do not overwrite already loaded certificates
load-from-default(15) = load default configuration (from GENFILES)
| |||||||||||||
| CbiboAdmConfigObject | 1.3.6.1.4.1.272.4.1.14.1.2 | OBJECT IDENTIFIER | RW | ||||||||||
column · OBJECT IDENTIFIER · read-write · current Table object id (OID) to save/load. If this field is set, only this table is saved/loaded. Otherwise all tables are saved/loaded. | |||||||||||||
| CbiboAdmConfigPath | 1.3.6.1.4.1.272.4.1.14.1.3 | DisplayString | RW | ||||||||||
column · DisplayString · read-write · current NAme of the configuration file in flash memory to save/load. | |||||||||||||
| CbiboAdmConfigPathNew | 1.3.6.1.4.1.272.4.1.14.1.4 | DisplayString | RW | ||||||||||
column · DisplayString · read-write · current New name of configuration file in flash memory to move/copy | |||||||||||||
| CbiboAdmConfigHost | 1.3.6.1.4.1.272.4.1.14.1.5 | IpAddress | RW | ||||||||||
column · IpAddress · read-write · current TFTP host's IP address to send/receive the file to/from. The configuration is transfered directly from flash memory (biboAdmConfigPath) to TFTP-file (biboAdmConfigFile). | |||||||||||||
| CbiboAdmConfigState | 1.3.6.1.4.1.272.4.1.14.1.6 | INTEGER | RO | ||||||||||
column · INTEGER · read-only · current The state of this command (i.e., biboAdmConfigCmd).
todo(1) : the command will start soon
running(2) : the command is currently executing
done(3) : the command has successfully completed
error(4) : the command has failed (see biboAdmSyslogTable)
delayed(5) : the command is delayed due to given Timeout
stopped(6) : the command has stopped (Timeout set to -1)
| |||||||||||||
| CbiboAdmConfigFile | 1.3.6.1.4.1.272.4.1.14.1.7 | DisplayString | RW | ||||||||||
column · DisplayString · read-write · current TFTP filename to read/write from/to the specified host. The configuration file received is stored in flash memory specified by biboAdmConfigPath. The actual configuration is not changed. | |||||||||||||
| CbiboAdmConfigTimeout | 1.3.6.1.4.1.272.4.1.14.1.8 | INTEGER | RW | ||||||||||
column · INTEGER · read-write · current Set this value (default 0) to delay a new command for this
amount of seconds.
The value is counting down to show the remaining time
(State=delayed).
To stop a scheduled but delayed command set this value
to -1.
timeout = 0 cmd executed immediately (default)
timeout > 0 cmd executed in timeout seconds (counting down)
timeout < 0 cmd execution stopped (deleted) | |||||||||||||
| CbiboAdmConfigHostUrl | 1.3.6.1.4.1.272.4.1.14.1.9 | DisplayString | RW | ||||||||||
column · DisplayString · read-write · current This is a host URL specifying the location to retrieve or store the configuration file. The last filename part must be missing and is given in biboAdmConfigFile. If this object is given biboAdmConfigHost is ignored. format: http://server/path/ tftp://server/path/ xmodem:[1k][@9600] | |||||||||||||
| CbiboAdmConfigCertIndex | 1.3.6.1.4.1.272.4.1.14.1.10 | INTEGER | RW | ||||||||||
column · INTEGER · read-write · current The index of the certificate to use (from the certTable). Only used for biboAdmConfigCmd = get / get-all and for use with biboAdmConfigHostUrl, of course. If set to 0, no client certificate is used. Default value is 0. | |||||||||||||
| TbiboAdmConfigDirTable | 1.3.6.1.4.1.272.4.1.15 | NA | |||||||||||
table · not-accessible · current Configuration directory table. This table contains all available configuration files in flash memory. | |||||||||||||
| RbiboAdmConfigDirEntry | 1.3.6.1.4.1.272.4.1.15.1 | NA | |||||||||||
row · not-accessible · current
| |||||||||||||
| CbiboAdmConfigDirName | 1.3.6.1.4.1.272.4.1.15.1.1 | DisplayString | RO | ||||||||||
column · DisplayString · read-only · current Name of the configuration file in flash memory. | |||||||||||||
| CbiboAdmConfigDirCount | 1.3.6.1.4.1.272.4.1.15.1.2 | INTEGER | RO | ||||||||||
column · INTEGER · read-only · current Number of tables saved in the file. | |||||||||||||
| CbiboAdmConfigDirContent | 1.3.6.1.4.1.272.4.1.15.1.3 | DisplayString | RO | ||||||||||
column · DisplayString · read-only · current Description of directory's contents (e.g., <all> or a series of table numbers). | |||||||||||||
| CbiboAdmConfigDirSaveDate | 1.3.6.1.4.1.272.4.1.15.1.4 | DisplayString | RO | ||||||||||
column · DisplayString · read-only · current Date when configuration was saved. It reflects value of variable biboExtAdmConfigSaveDate which gets set when the configuration is saved to flash. This also means: if a configuration doesn't contain this variable no date is available. | |||||||||||||
| TbiboAdmBoardTable | 1.3.6.1.4.1.272.4.1.17 | NA | |||||||||||
table · not-accessible · current The biboAdmBoardTable lists information about the installed communications modules. This table is updated after every system boot up. Creating entries: Entries are created by the system upon detecting the installed hardware. Deleting entries: Entries are removed by the system as a result of removed hardware. | |||||||||||||
| RbiboAdmBoardEntry | 1.3.6.1.4.1.272.4.1.17.1 | NA | |||||||||||
row · not-accessible · current
| |||||||||||||
| CbiboABrdSlot | 1.3.6.1.4.1.272.4.1.17.1.1 | INTEGER (0..31) | RO | ||||||||||
column · INTEGER (0..31) · read-only · current The slot, or location of this module. | |||||||||||||
| CbiboABrdType | 1.3.6.1.4.1.272.4.1.17.1.2 | DisplayString | RO | ||||||||||
column · DisplayString · read-only · current The name of this module. | |||||||||||||
| CbiboABrdHWRelease | 1.3.6.1.4.1.272.4.1.17.1.3 | DisplayString | RO | 1.0 | |||||||||
column · DisplayString · read-only · current The hardware release of this module. Example values from LibreNMS test devices
| |||||||||||||
| CbiboABrdFWRelease | 1.3.6.1.4.1.272.4.1.17.1.4 | DisplayString | RO | ||||||||||
column · DisplayString · read-only · current The firmware release of this module. | |||||||||||||
| CbiboABrdPartNo | 1.3.6.1.4.1.272.4.1.17.1.5 | DisplayString | RO | be.IP plus | |||||||||
column · DisplayString · read-only · current The part number of this module. Example values from LibreNMS test devices
| |||||||||||||
| CbiboABrdConnector | 1.3.6.1.4.1.272.4.1.17.1.6 | INTEGER | RW | obsolete | |||||||||
column · INTEGER · read-write · obsolete The type of connector used for this module. For modules with more than one connector this value can be changed/switched by setting this object. For example, the CM-BNCTP module supports both twisted pair (RJ45) and 10Base2 (BNC) connectors. If this object is set to 'AUTO' then the BRICK will automatically detect which connector type is being used.
| |||||||||||||
| CbiboABrdUnit | 1.3.6.1.4.1.272.4.1.17.1.7 | INTEGER (0..99) | RO | ||||||||||
column · INTEGER (0..99) · read-only · current The logical unit number of this interface. | |||||||||||||
| CbiboABrdSerialNo | 1.3.6.1.4.1.272.4.1.17.1.8 | DisplayString | RO | BE2CAM019320050 | |||||||||
column · DisplayString · read-only · current The serial number of this module. Example values from LibreNMS test devices
| |||||||||||||
| CbiboABrdCategory | 1.3.6.1.4.1.272.4.1.17.1.9 | INTEGER | RO | ||||||||||
column · INTEGER · read-only · current Board category. It can be one of the following: system-board(1), ethernet(2), isdn-bri(3), isdn-pmx(4), pots(5), dsl(6), wlan(7), tty(8), dsp(9), usb(10), crypt(11), mobile(12) It advices users of which MIB table to look at when searching for additional configuration informations.
| |||||||||||||
| TbiboAdmUsrTrapTable | 1.3.6.1.4.1.272.4.1.18 | NA | |||||||||||
table · not-accessible · current The biboAdmUsrTrapTable lists user-defined objects that are used to create traps. These traps are sent locally, but can also be sent to remote hosts using the biboAdmTrapHostTable. Creating entries: Entries are created by assigning the biboATrpObj object a valid object identifier. Deleting entries: Entries are removed by setting the entry's biboATrpStatus object to 'delete'. | |||||||||||||
| RbiboAdmUsrTrapEntry | 1.3.6.1.4.1.272.4.1.18.1 | NA | |||||||||||
row · not-accessible · current
| |||||||||||||
| CbiboATrpObj | 1.3.6.1.4.1.272.4.1.18.1.1 | OBJECT IDENTIFIER | RW | ||||||||||
column · OBJECT IDENTIFIER · read-write · current The object identifier of an object to use. Each time this object's value changes, a trap is created and sent. Either a single leaf (single variable) or a table (of objects) can be specified. | |||||||||||||
| CbiboATrpStatus | 1.3.6.1.4.1.272.4.1.18.1.2 | INTEGER | RW | ||||||||||
column · INTEGER · read-write · current The status of this entry. Upon creation of a new entry, this object's value is set to 'valid'.
| |||||||||||||
| SbiboAdmDomainName | 1.3.6.1.4.1.272.4.1.19 | DisplayString | RW | ||||||||||
scalar · DisplayString · read-write · current Domain name. | |||||||||||||
| SbiboAdmNameServer | 1.3.6.1.4.1.272.4.1.20 | IpAddress | RW | ||||||||||
scalar · IpAddress · read-write · current IP address of name server. | |||||||||||||
| SbiboAdmNameServ2 | 1.3.6.1.4.1.272.4.1.21 | IpAddress | RW | ||||||||||
scalar · IpAddress · read-write · current IP address of second name server. | |||||||||||||
| SbiboAdmBridgeEnable | 1.3.6.1.4.1.272.4.1.22 | INTEGER | RW | obsolete | |||||||||
scalar · INTEGER · read-write · obsolete Sets bridging to enable / disable status.
| |||||||||||||
| SbiboAdmCapiTcpPort | 1.3.6.1.4.1.272.4.1.23 | INTEGER | RW | ||||||||||
scalar · INTEGER · read-write · current TCP port for remote CAPI demon. | |||||||||||||
| SbiboAdmTraceTcpPort | 1.3.6.1.4.1.272.4.1.24 | INTEGER | RW | ||||||||||
scalar · INTEGER · read-write · current TCP port for trace demon. | |||||||||||||
| SbiboAdmRipUdpPort | 1.3.6.1.4.1.272.4.1.25 | INTEGER | RW | ||||||||||
scalar · INTEGER · read-write · current UDP port for RIP. Setting this object to zero disables RIP. | |||||||||||||
| SbiboAdmSWVersion | 1.3.6.1.4.1.272.4.1.26 | DisplayString (SIZE (0..255)) | RO | V.10.2.9.102 IPv6, IPSec, PBX from 2021/03/16 0… | |||||||||
scalar · DisplayString (SIZE (0..255)) · read-only · current This is the software release version. It's either identical to biboAdmSWVersionOS or biboAdmSWVersionOEM. Example values from LibreNMS test devices
| |||||||||||||
| SbiboAdmTimeServer | 1.3.6.1.4.1.272.4.1.27 | IpAddress | RO | ||||||||||
scalar · IpAddress · read-only · current The IP address of the time server. | |||||||||||||
| SbiboAdmTimeOffset | 1.3.6.1.4.1.272.4.1.28 | INTEGER | RW | ||||||||||
scalar · INTEGER · read-write · current This is the time offset from GMT in seconds. If the set value is in the range from -24 to 24, it means hours, and is automatically converted to seconds. | |||||||||||||
| SbiboAdmConsoleSyslog | 1.3.6.1.4.1.272.4.1.29 | INTEGER | RW | ||||||||||
scalar · INTEGER · read-write · current Specifies whether to direct syslog messages to the console.
| |||||||||||||
| SbiboAdmSyslogTableLevel | 1.3.6.1.4.1.272.4.1.30 | INTEGER | RW | ||||||||||
scalar · INTEGER · read-write · current Specifies which message levels to post to the biboAdmSyslogTable and the console, if applicable.
| |||||||||||||
| SbiboAdmSystemId | 1.3.6.1.4.1.272.4.1.31 | DisplayString | RO | ||||||||||
scalar · DisplayString · read-only · current This object contains the system Identification String. | |||||||||||||
| TbiboAdmLicInfoTable | 1.3.6.1.4.1.272.4.1.32 | NA | |||||||||||
table · not-accessible · current This table contains an entry for each feature, that can be activated by a license. The licenses have to be entered in the biboAdmLicenseTable. This tabl indicates the current state of the different licenses. | |||||||||||||
| RbiboAdmLicInfoEntry | 1.3.6.1.4.1.272.4.1.32.1 | NA | |||||||||||
row · not-accessible · current | |||||||||||||
| CbiboAdmLicInfoType | 1.3.6.1.4.1.272.4.1.32.1.1 | INTEGER | RO | ||||||||||
column · INTEGER · read-only · current The licenseable feature.
| |||||||||||||
| CbiboAdmLicInfoStatus | 1.3.6.1.4.1.272.4.1.32.1.2 | INTEGER | RO | ||||||||||
column · INTEGER · read-only · current The current state of the license.
| |||||||||||||
| CbiboAdmLicInfoId | 1.3.6.1.4.1.272.4.1.32.1.3 | DisplayString | RO | ||||||||||
column · DisplayString · read-only · current The complete serial id string of the special license. | |||||||||||||
| CbiboAdmLicInfoSlot | 1.3.6.1.4.1.272.4.1.32.1.4 | INTEGER (0..255) | RO | ||||||||||
column · INTEGER (0..255) · read-only · current In case of a hardware license corresponding to a dedicated module serial number, it is the slot number of the module. | |||||||||||||
| CbiboAdmLicInfoMaxLic | 1.3.6.1.4.1.272.4.1.32.1.5 | Counter32 | RO | ||||||||||
column · Counter32 · read-only · current The max number of allowed chunks. | |||||||||||||
| CbiboAdmLicInfoInUse | 1.3.6.1.4.1.272.4.1.32.1.6 | Counter32 | RO | ||||||||||
column · Counter32 · read-only · current The current number of chunks in use. | |||||||||||||
| CbiboAdmLicInfoHwSerial | 1.3.6.1.4.1.272.4.1.32.1.7 | DisplayString | RO | ||||||||||
column · DisplayString · read-only · current The complete serial id string of the special license. | |||||||||||||
| CbiboAdmLicInfoUnit | 1.3.6.1.4.1.272.4.1.32.1.8 | INTEGER (0..255) | RO | ||||||||||
column · INTEGER (0..255) · read-only · current In case of a hardware license corresponding to a dedicated module serial number, it is the unit number of the module. | |||||||||||||
| CbiboAdmLicInfoLimit | 1.3.6.1.4.1.272.4.1.32.1.9 | Counter32 | RO | ||||||||||
column · Counter32 · read-only · current The maximum number of licenseable chunks. | |||||||||||||
| CbiboAdmLicInfoFree | 1.3.6.1.4.1.272.4.1.32.1.10 | Counter32 | RO | ||||||||||
column · Counter32 · read-only · current The number of free default licences. | |||||||||||||
| SbiboAdmBootpRelayServer | 1.3.6.1.4.1.272.4.1.33 | IpAddress | RW | ||||||||||
scalar · IpAddress · read-write · current This object contains the destination IP address to
which BOOTP/DHCP request are forwarded by the
BIANCA/BRICK BOOTP relay agent.
If this entry is empty no BOOTP forwarding is done. | |||||||||||||
| SbiboAdmRadiusServer | 1.3.6.1.4.1.272.4.1.34 | IpAddress | RW | ||||||||||
scalar · IpAddress · read-write · current This object contains the IP address of the RADIUS server (remote dial in user service). If set to 0.0.0.0 RADIUS services are generally disabled (default). The corresponding Radius password is configured in the biboAdmRadiusSecret variable. | |||||||||||||
| SbiboAdmLocalPPPIdent | 1.3.6.1.4.1.272.4.1.35 | DisplayString | RW | ||||||||||
scalar · DisplayString · read-write · current This is the local ID string used for PPP authentication (PAP/CHAP). In pre4.3 versions the sysName has been used as the local ID string. This is, for increased ease and transparency of system configuration, no longer true. | |||||||||||||
| SbiboAdmHttpTcpPort | 1.3.6.1.4.1.272.4.1.36 | INTEGER | RW | ||||||||||
scalar · INTEGER · read-write · current TCP port for the HTTP server. Default port is 80, 0 disables the HTTP server. | |||||||||||||
| SbiboAdmTapiTcpPort | 1.3.6.1.4.1.272.4.1.37 | INTEGER | RW | ||||||||||
scalar · INTEGER · read-write · current TCP port for remote TAPI demon. | |||||||||||||
| SbiboAdmTimeProtocol | 1.3.6.1.4.1.272.4.1.38 | INTEGER | RO | ||||||||||
scalar · INTEGER · read-only · current This field specifies from which source the bricks internal clock is synchronised: none(1) = no time synchronisation time-udp(2) = UDP/TIME (RFC 868), from biboAdmTimeServer time-tcp(3) = TCP/TIME (RFC 868), from biboAdmTimeServer time-sntp(4) = SNTP (RFC 1769), from biboAdmTimeServer isdn(5) = examines ISDN time, from controller stack 0
| |||||||||||||
| SbiboAdmTimeUpdate | 1.3.6.1.4.1.272.4.1.39 | INTEGER | RW | ||||||||||
scalar · INTEGER · read-write · current This is the interval for timeserver requests (in seconds). If the set value is in the range from -24 to 24, it means hours, and is automatically converted to seconds. If the time comes from ISDN, the time is updated with the next call after this interval. | |||||||||||||
| SbiboAdmWINS1 | 1.3.6.1.4.1.272.4.1.40 | IpAddress | RW | ||||||||||
scalar · IpAddress · read-write · current The IP address of the WINS server (NetBIOS Name Server). | |||||||||||||
| SbiboAdmWINS2 | 1.3.6.1.4.1.272.4.1.41 | IpAddress | RW | ||||||||||
scalar · IpAddress · read-write · current The IP address of the alternate WINS server. | |||||||||||||
| TbiboAdmCardTable | 1.3.6.1.4.1.272.4.1.42 | NA | |||||||||||
table · not-accessible · current The biboAdmCardTable lists installed cards. | |||||||||||||
| RbiboAdmCardEntry | 1.3.6.1.4.1.272.4.1.42.1 | NA | |||||||||||
row · not-accessible · current
| |||||||||||||
| CbiboACrdSlot | 1.3.6.1.4.1.272.4.1.42.1.1 | INTEGER (0..31) | RO | ||||||||||
column · INTEGER (0..31) · read-only · current The slot, or location of this card. | |||||||||||||
| CbiboACrdType | 1.3.6.1.4.1.272.4.1.42.1.2 | DisplayString | RO | ||||||||||
column · DisplayString · read-only · current The name of this card. | |||||||||||||
| CbiboACrdState | 1.3.6.1.4.1.272.4.1.42.1.3 | INTEGER | RO | ||||||||||
column · INTEGER · read-only · current State of the card.
| |||||||||||||
| CbiboACrdCpldVersion | 1.3.6.1.4.1.272.4.1.42.1.4 | DisplayString | RO | ||||||||||
column · DisplayString · read-only · current Version of onboard CPLD. | |||||||||||||
| CbiboACrdFpgaVersion | 1.3.6.1.4.1.272.4.1.42.1.5 | DisplayString | RO | ||||||||||
column · DisplayString · read-only · current Version of loaded FPGA firmware. | |||||||||||||
| CbiboACrdTemp | 1.3.6.1.4.1.272.4.1.42.1.6 | INTEGER (0..250) | RO | ||||||||||
column · INTEGER (0..250) · read-only · current This variable shows the actual card temperature in the unit Celsius. | |||||||||||||
| CbiboACrdTempAlarmThreshold | 1.3.6.1.4.1.272.4.1.42.1.7 | INTEGER (0..250) | RW | ||||||||||
column · INTEGER (0..250) · read-write · current Card temperature threshold. | |||||||||||||
| CbiboACrdTempAlarmTrap | 1.3.6.1.4.1.272.4.1.42.1.8 | INTEGER | RO | ||||||||||
column · INTEGER · read-only · current If the card temperature raises above the threshold, a trap is generated every 60 seconds.
| |||||||||||||
| CbiboACrdAdmin | 1.3.6.1.4.1.272.4.1.42.1.9 | INTEGER | RW | ||||||||||
column · INTEGER · read-write · current Administrative manipulation of card state.
| |||||||||||||
| CbiboACrdTempAlarmThresholdCriticalLow | 1.3.6.1.4.1.272.4.1.42.1.10 | INTEGER (0..250) | RW | ||||||||||
column · INTEGER (0..250) · read-write · current Lower Card temperature threshold to return state from critical to normal. Mustn't exceed biboACrdTempAlarmThreshold! When temperature reaches biboACrdTempAlarmThreshold state changes to critical. This state persists until temperature falls below biboACrdTempAlarmThreshUncriticalLow where state changes back to normal. | |||||||||||||
| NbiboAdmTraps | 1.3.6.1.4.1.272.4.1.43 | ||||||||||||
| !biboAdmTrapACrdTempCritical | 1.3.6.1.4.1.272.4.1.43.0.1 | ||||||||||||
notification This trap signifies that the Card temperature raises above the critical alarm-threshold | |||||||||||||
| !biboAdmTrapACrdTempOk | 1.3.6.1.4.1.272.4.1.43.0.2 | ||||||||||||
notification A normal Card temperature has been restored. | |||||||||||||
| !biboAdmTrapACrdDown | 1.3.6.1.4.1.272.4.1.43.0.3 | ||||||||||||
notification This trap signifies that the specified Card is down
| |||||||||||||
| !biboAdmTrapACrdRunning | 1.3.6.1.4.1.272.4.1.43.0.4 | ||||||||||||
notification This trap signifies that the specified Card is up/running
| |||||||||||||
| !biboAdmTrapACrdFailed | 1.3.6.1.4.1.272.4.1.43.0.5 | ||||||||||||
notification This trap signifies that the specified Card has failed
| |||||||||||||
| !biboAdmTrapACrdStopped | 1.3.6.1.4.1.272.4.1.43.0.6 | ||||||||||||
notification This trap signifies that the specified Card is stopped
| |||||||||||||
| SbiboAdmExtendedBanner | 1.3.6.1.4.1.272.4.1.45 | DisplayString | RW | ||||||||||
scalar · DisplayString · read-write · current This is an additional banner message which is displayed after the standard welcome message at boot time. This message is typically used to display info regarding a special configuration of the router. | |||||||||||||
| SbiboAdmBootpRelayServ2 | 1.3.6.1.4.1.272.4.1.47 | IpAddress | RW | ||||||||||
scalar · IpAddress · read-write · current This object contains the second destination IP address to which BOOTP/DHCP request are forwarded by the BIANCA/BRICK BOOTP relay agent. If this entry is empty no BOOTP forwarding is done. | |||||||||||||
| SbiboAdmTimedBootPolicy | 1.3.6.1.4.1.272.4.1.48 | INTEGER | RW | ||||||||||
scalar · INTEGER · read-write · current This object specifies the frequency with which the timed requests the time (using the specified time protocol) after system startup until the first reply is received. Possible values: normal(1): -- 5 retries after 1, 2, 4, 8, 16 minutes aggressive(2): -- retry 10 minutes with 1, 2, 4, 8, 10, 10, ... seconds of timeout endless(3): -- same as aggressive except there is no time limit.
| |||||||||||||
| SbiboAdmAcctlogFormat | 1.3.6.1.4.1.272.4.1.49 | DisplayString (SIZE (0..255)) | RW | ||||||||||
scalar · DisplayString (SIZE (0..255)) · read-write · current Specifies the format of accounting messages sent by
the syslog protocol. The format can consist of any order
of random strings, backslash escaped sequences like '\t','\n', etc.
or the following format tags:
Tag Meaning
%d Date the session opened; in DD.MM.YY format.
%t Time the session opened: in HH:MM:SS format
%a session age in seconds
%c protocol type
%i source IP address
%r source port
%f source interface index
%I destination IP address
%R destination port
%F destination interface index
%p outgoing packets
%o outgoing octets
%P incoming packets
%O incoming octets
%s message sequence counter
%% '%'
The format for accounting messages is per default:
'INET: %d %t %a %c %i:%r/%f -> %I:%R/%F %p %o %P %O [%s]' | |||||||||||||
| SbiboAdmAcctlogMaxEntries | 1.3.6.1.4.1.272.4.1.50 | INTEGER | RW | ||||||||||
scalar · INTEGER · read-write · current Maximum Number of accounting messages stored in memory. | |||||||||||||
| TbiboAdmAcctlogTable | 1.3.6.1.4.1.272.4.1.51 | NA | |||||||||||
table · not-accessible · current The biboAdmAcctlogTable keeps track of accounting messages received. The columns specify attributes for each message generated. As this information only reports events on the system, all fields are read-only. Creating entries: Entries can only be created by the system and are made each time a message for accounting is generated. Deleting entries: Entries are removed by the system the messages are sent to the loghost. | |||||||||||||
| RbiboAdmAcctlogEntry | 1.3.6.1.4.1.272.4.1.51.1 | NA | |||||||||||
row · not-accessible · current
| |||||||||||||
| CbiboAdmAcctlogTimeStamp | 1.3.6.1.4.1.272.4.1.51.1.1 | Date | RO | ||||||||||
column · Date · read-only · current Time message was generated. | |||||||||||||
| CbiboAdmAcctlogLevel | 1.3.6.1.4.1.272.4.1.51.1.2 | INTEGER | RO | ||||||||||
column · INTEGER · read-only · current Level of acct message.
| |||||||||||||
| CbiboAdmAcctlogMessage | 1.3.6.1.4.1.272.4.1.51.1.4 | DisplayString | RO | ||||||||||
column · DisplayString · read-only · current The text of the acct message. | |||||||||||||
| CbiboAdmAcctlogSubject | 1.3.6.1.4.1.272.4.1.51.1.5 | INTEGER | RO | ||||||||||
column · INTEGER · read-only · current Subject of the acct message.
| |||||||||||||
| SbiboAdmTimeSource | 1.3.6.1.4.1.272.4.1.52 | INTEGER | RO | ||||||||||
scalar · INTEGER · read-only · current The source of the current system time.
| |||||||||||||
| SbiboAdmIsdnTimeUpdate | 1.3.6.1.4.1.272.4.1.53 | INTEGER | RW | ||||||||||
scalar · INTEGER · read-write · current This object specifies whether a time value which has been retrieved via ISDN should be used to set the system time. Note that the time retrieved via ISDN is ignored if the system time has been set by a time server previously.
| |||||||||||||
| TtimeServerTable | 1.3.6.1.4.1.272.4.1.54 | NA | |||||||||||
table · not-accessible · current This table contains the list of time servers. | |||||||||||||
| RtimeServerEntry | 1.3.6.1.4.1.272.4.1.54.1 | NA | |||||||||||
| CtimeSrvPriority | 1.3.6.1.4.1.272.4.1.54.1.1 | INTEGER (0..128) | RW | ||||||||||
column · INTEGER (0..128) · read-write · current The priority of the time server. The time servers are queried in the order of ascending priority value, i.e. 0 first, 1 second ... . | |||||||||||||
| CtimeSrvProtocol | 1.3.6.1.4.1.272.4.1.54.1.2 | INTEGER | RW | ||||||||||
column · INTEGER · read-write · current The protocol used for the time server.
| |||||||||||||
| CtimeSrvAddress | 1.3.6.1.4.1.272.4.1.54.1.3 | DisplayString | RW | ||||||||||
column · DisplayString · read-write · current The IP Address or DNS name of the time server. If a DNS name is specified here, it is resolved on demand. | |||||||||||||
| SbiboAdmSyslogTcpRetries | 1.3.6.1.4.1.272.4.1.55 | INTEGER | RW | ||||||||||
scalar · INTEGER · read-write · current Maximum number of attempts to connect a syslog server over TCP. | |||||||||||||
| SbiboAdmSWVersionOS | 1.3.6.1.4.1.272.4.1.56 | DisplayString (SIZE (0..255)) | RO | ||||||||||
scalar · DisplayString (SIZE (0..255)) · read-only · current This is the OS software release version as it was always found in biboAdmSWVersion. | |||||||||||||
| SbiboAdmSWVersionOEM | 1.3.6.1.4.1.272.4.1.57 | DisplayString (SIZE (0..255)) | RO | ||||||||||
scalar · DisplayString (SIZE (0..255)) · read-only · current This is the OEM software release version. Either there's a separate OEM version defined or this is identical to biboAdmSWVersionOS. | |||||||||||||
| SbiboAdmStartMode | 1.3.6.1.4.1.272.4.1.58 | INTEGER | RO | ||||||||||
scalar · INTEGER · read-only · current If service procedure is activated, mode is set to service, otherwise mode is set to normal.
| |||||||||||||
| SbiboAdmNTPServer | 1.3.6.1.4.1.272.4.1.59 | INTEGER | RW | ||||||||||
scalar · INTEGER · read-write · current This field controls the NTP server. If it is set to disabled(1) client requests will be ignored. Setting it to enabled(2) on every client request a server answer is transmitted. In clientdepend(3) mode only a answer to a client request is sent if an external reference exists.
| |||||||||||||
| SbiboAdmTimeZone | 1.3.6.1.4.1.272.4.1.60 | DisplayString | RW | ||||||||||
scalar · DisplayString · read-write · current The name of the currently set timezone. The corresponding timezone must exist in timeZoneTable. | |||||||||||||
| TtimeZoneTable | 1.3.6.1.4.1.272.4.1.61 | NA | |||||||||||
table · not-accessible · current This table contains the list of availabe timezones. | |||||||||||||
| RtimeZoneEntry | 1.3.6.1.4.1.272.4.1.61.1 | NA | |||||||||||
| CtimeZoneIndex | 1.3.6.1.4.1.272.4.1.61.1.1 | INTEGER | RO | ||||||||||
column · INTEGER · read-only · current Index in Timezone Table. | |||||||||||||
| CtimeZoneName | 1.3.6.1.4.1.272.4.1.61.1.2 | DisplayString | RO | ||||||||||
column · DisplayString · read-only · current The Name of a Timezone. | |||||||||||||
| CtimeZoneAlias | 1.3.6.1.4.1.272.4.1.61.1.3 | DisplayString | RO | ||||||||||
column · DisplayString · read-only · current The abbreviation of a timezone. | |||||||||||||
| CtimeZoneOffset | 1.3.6.1.4.1.272.4.1.61.1.4 | INTEGER | RO | ||||||||||
column · INTEGER · read-only · current Timezone offset from UTC in seconds. Note that this contains no information about daylight saving for this timezone | |||||||||||||
| TntpServerTable | 1.3.6.1.4.1.272.4.1.64 | NA | |||||||||||
table · not-accessible · current List of DHCP-client-learned NTP-servers, relevant only if related administrative table timeServer is empty. | |||||||||||||
| RntpServerEntry | 1.3.6.1.4.1.272.4.1.64.1 | NA | |||||||||||
| CntpServerPriority | 1.3.6.1.4.1.272.4.1.64.1.1 | INTEGER (0..128) | RO | ||||||||||
column · INTEGER (0..128) · read-only · current Priority of NTP-server. Lower value means 'preferred'. | |||||||||||||
| CntpServerAddress | 1.3.6.1.4.1.272.4.1.64.1.2 | DisplayString | RO | ||||||||||
column · DisplayString · read-only · current IP-address or FQDN of NTP-server. | |||||||||||||
| NtraceBuffers | 1.3.6.1.4.1.272.4.1.65 | ||||||||||||
| NtrcBufAdmin | 1.3.6.1.4.1.272.4.1.65.1 | ||||||||||||
| TtrcBufTable | 1.3.6.1.4.1.272.4.1.65.1.1 | NA | |||||||||||
table · not-accessible · current This table contains the list trace buffers. | |||||||||||||
| RtrcBufEntry | 1.3.6.1.4.1.272.4.1.65.1.1.1 | NA | |||||||||||
| CtrcBufIndex | 1.3.6.1.4.1.272.4.1.65.1.1.1.1 | INTEGER | RO | ||||||||||
column · INTEGER · read-only · current Unique Index of the trace buffer | |||||||||||||
| CtrcBufDevice | 1.3.6.1.4.1.272.4.1.65.1.1.1.2 | DisplayString | RO | ||||||||||
column · DisplayString · read-only · current The device representing this trace buffer | |||||||||||||
| CtrcBufMode | 1.3.6.1.4.1.272.4.1.65.1.1.1.3 | INTEGER | RO | ||||||||||
column · INTEGER · read-only · current Indicates operation mode of trace buffer: single-shot: just fill buffer up to maximum size continuous: ring buffer mode In single-shot mode every write attempt that would exceed buffer limits, causes the buffer to get closed for writing and the write attempt to fail (as any further attempts will). In continuous mode the buffer is filled up to the maximum size, and overwrite older data as new data gets written. Variable is meaningless as long as variable trcBufOperation is set to unused.
| |||||||||||||
| CtrcBufDataMode | 1.3.6.1.4.1.272.4.1.65.1.1.1.4 | INTEGER | RO | ||||||||||
column · INTEGER · read-only · current Indicates how trace buffer treats data written to it:
In bytestream mode no structure is imposed on written data,
buffer will get completely filled up if enough data is written.
Data overwrite is done byte-by-byte.
Mode message keeps the data structure in messages as passed
down to the trace buffer and allows for reading them back in
same portions as written.
Mode message-per-session treats any data written to trace
buffer between opening and closing it as one message.
Variable is meaningless as long as variable trcBufOperation
is set to unused.
NOTE: modes message and message-per-session only reflect the
last state; it depends on the application(s) writing to the
trace buffer in which mode it is used, so this variable can
toggle between these two states over time.
| |||||||||||||
| CtrcBufSize | 1.3.6.1.4.1.272.4.1.65.1.1.1.5 | INTEGER | RO | ||||||||||
column · INTEGER · read-only · current The maximum size of the trace buffer | |||||||||||||
| CtrcBufDataSize | 1.3.6.1.4.1.272.4.1.65.1.1.1.6 | INTEGER | RO | ||||||||||
column · INTEGER · read-only · current The current data size of the trace buffer | |||||||||||||
| CtrcBufDate | 1.3.6.1.4.1.272.4.1.65.1.1.1.7 | Date | RO | ||||||||||
column · Date · read-only · current Time and date of the buffer creation | |||||||||||||
| CtrcBufDescr | 1.3.6.1.4.1.272.4.1.65.1.1.1.8 | DisplayString | RO | ||||||||||
column · DisplayString · read-only · current Optional descriptive information of the buffer's purpose. | |||||||||||||
| CtrcBufID | 1.3.6.1.4.1.272.4.1.65.1.1.1.9 | Unsigned32 | RO | ||||||||||
column · Unsigned32 · read-only · current Optional identificator for the buffer. | |||||||||||||
| CtrcBufOperation | 1.3.6.1.4.1.272.4.1.65.1.1.1.10 | INTEGER | RO | ||||||||||
column · INTEGER · read-only · current The current status of the trace buffer:
unused: Device is free to be used
idle : Device is parameterized but not open
read : Device is open for reading
write: Device is open for writing
read-write: Device is open for reading and writing
full: No more writing to buffer possible
Value read-write would normally refer to two processes.
Value full indicates that no more data can be written to
buffer; it will remain unchanged until it gets deleted.
| |||||||||||||
| NtrcBufOper | 1.3.6.1.4.1.272.4.1.65.2 | ||||||||||||
| StrcBufStatNBufs | 1.3.6.1.4.1.272.4.1.65.2.1 | Unsigned32 | RO | ||||||||||
scalar · Unsigned32 · read-only · current Number of trace buffers supported by running firmware. | |||||||||||||
| NtrcBufStat | 1.3.6.1.4.1.272.4.1.65.3 | ||||||||||||
| StrcBufStatNUnused | 1.3.6.1.4.1.272.4.1.65.3.1 | Unsigned32 | RO | ||||||||||
scalar · Unsigned32 · read-only · current Number of trace buffers currently available to store data. | |||||||||||||
| StrcBufStatNOpen | 1.3.6.1.4.1.272.4.1.65.3.2 | Unsigned32 | RO | ||||||||||
scalar · Unsigned32 · read-only · current Number of trace buffers currently available for appending data. | |||||||||||||
| StrcBufStatNFull | 1.3.6.1.4.1.272.4.1.65.3.3 | Unsigned32 | RO | ||||||||||
scalar · Unsigned32 · read-only · current Number of trace buffers currently available for reading data only (i.e. in state 'full'). | |||||||||||||
| NsysStat | 1.3.6.1.4.1.272.4.17.500 | ||||||||||||
| SsysStatBootConfig | 1.3.6.1.4.1.272.4.17.500.1 | INTEGER | RO | ||||||||||
scalar · INTEGER · read-only · current After system boot this variable shows which configuration was loaded: none: no configuration whatsoever bootfac: factory boot configuration default: default configuration as provided by image boot: configuration found in flash.
| |||||||||||||
| SsysStatFunctionState | 1.3.6.1.4.1.272.4.17.500.2 | INTEGER | RO | ||||||||||
scalar · INTEGER · read-only · current This variable contains the current function state, which is toggeled by pressing the function button on the device.
| |||||||||||||
| SsysStatOperationMode | 1.3.6.1.4.1.272.4.17.500.3 | INTEGER | RO | ||||||||||
scalar · INTEGER · read-only · current This variable defines the operation mode of the device concerning telephony functionality. If any voice functionality is integrated it can be either mgw(1) for Media GateWay functionality of pbx(2) for a full-fledged telephone system. For systems w/o voice functionality the variable has value plain(0).
| |||||||||||||
| SsysStatConfigConvert | 1.3.6.1.4.1.272.4.17.500.4 | INTEGER | RW | ||||||||||
scalar · INTEGER · read-write · current This variable handles the Configuration Conversion from
pbx to mgw (later may be mgw to pbx)
For systems w/o voice functionality the variable has value
plain(0).
| |||||||||||||
| SsysStatConfigConvertState | 1.3.6.1.4.1.272.4.17.500.5 | INTEGER | RO | ||||||||||
scalar · INTEGER · read-only · current This variable handles the Configuration Conversion state
idle - No conversion in progress
progress - conversion in progress
done - conversion done
failed - conversion not possible
The value is set to progress during tne coversion progress.
On errer e.g configuration parameters already exists the
State is set to failed otherwise the State is set to idle
on success.
| |||||||||||||
| Nadmin-2 | 1.3.6.1.4.1.272.4.22 | ||||||||||||
| Nextadmin | 1.3.6.1.4.1.272.4.22.1 | ||||||||||||
| SbiboExtAdmMonAddress | 1.3.6.1.4.1.272.4.22.1.1 | IpAddress | RW | ||||||||||
scalar · IpAddress · read-write · current The IP address of the host machine running the Activity Monitor program. This program displays the information about the current state of all interfaces. Periodically UDP packets are send to this IP address, to refresh the data automatically on the target host. The value 255.255.255.255 represents the broadcast address of the first LAN interface (e.g. 10.255.255.255), so more than one Activity Monitor on different hosts can receive the data. | |||||||||||||
| SbiboExtAdmMonPort | 1.3.6.1.4.1.272.4.22.1.2 | INTEGER (0..65535) | RW | ||||||||||
scalar · INTEGER (0..65535) · read-write · current UDP port for the Activity Monitor protocol. | |||||||||||||
| SbiboExtAdmMonType | 1.3.6.1.4.1.272.4.22.1.3 | INTEGER | RW | ||||||||||
scalar · INTEGER · read-write · current This parameter configures the content of the Activity Monitor
packets, or disables it:
off : Activity Monitor disabled
physical : send only physical interfaces information
physical-virt: send physical and virtual interface
information.
| |||||||||||||
| SbiboExtAdmMonUpdate | 1.3.6.1.4.1.272.4.22.1.4 | INTEGER (0..60) | RW | ||||||||||
scalar · INTEGER (0..60) · read-write · current This is the time interval for the Activity Monitor for sending packets (in seconds) to the specified IP address. The value of 0 disables sending Activity Monitor packets. | |||||||||||||
| SbiboExtAdmProcRouted | 1.3.6.1.4.1.272.4.22.1.5 | INTEGER | RW | ||||||||||
scalar · INTEGER · read-write · current enabled: The routed process is running.
RIP and/or OSPF are available (subject to licenses).
This is the default behavior of the system.
Hints:
RIP may be enabled/disabled by 'biboAdmRipUdpPort'
OSPF may be enabled/disabled by 'ospfAdminStat'
RIP may be if-specific ena/disabled by 'ipExtIfRip*'
OSPF may be if-specific ena/disabled by 'ipExtIfOspf'
... but a running routed process consumes CPU-Time
to keep in sync with interface/routing tables - even
if RIP and OSPF are disabled (global or if-specific).
disabled: The routed process is stopped.
RIP and/or OSPF are unavailable.
Hints:
A stopped routed process consumes no CPU-Time.
Set ipExtAdmProcRouted to 'disabled' is recommended
if both protocols (RIP and OSPF) not used in the
specific router environment.
| |||||||||||||
| SbiboExtAdmProcWatchDog | 1.3.6.1.4.1.272.4.22.1.7 | INTEGER | RW | ||||||||||
scalar · INTEGER · read-write · current enabled: The watchd process is running.
up/down transitions on interfaces delivered by
various protocols like ping/ifOperStatus/VRRP
are processed by parsing a task table and slave
interfaces are switched up/down according to the
task definition.
disabled: The watchd process is stopped.
| |||||||||||||
| SbiboExtAdmProcSSHd | 1.3.6.1.4.1.272.4.22.1.8 | INTEGER | RW | ||||||||||
scalar · INTEGER · read-write · current enabled: The sshd process is running. disabled: The sshd process is stopped.
| |||||||||||||
| SbiboExtAdmScheduleInterval | 1.3.6.1.4.1.272.4.22.1.9 | INTEGER (0..65535) | RW | ||||||||||
scalar · INTEGER (0..65535) · read-write · current This is the time interval in seconds for the Schedule daemon watching any events (recommended value: 300). The value 0 disables the scheduler. Referring table: scheduleTable | |||||||||||||
| SbiboExtAdmUpdatePath | 1.3.6.1.4.1.272.4.22.1.10 | DisplayString | RW | ||||||||||
scalar · DisplayString · read-write · current Default URL for automatic SW updates, e.g. http://server/path/
This setting is IGNORED if chkUpdSrvAdminOperURL is not empty.
Otherwise, related chkUpdSrv entry is allocated for it.
If URL does NOT end with '/' then it is considered being
complete and copied to related chkUpdSrvDownloadLink.
Otherwise, following parts are appended automatically.
'<sysname>[-<mode>]/<sysname>[-<mode>]-s_current' | |||||||||||||
| SbiboExtAdmBackRtVerify | 1.3.6.1.4.1.272.4.22.1.11 | INTEGER | RW | ||||||||||
scalar · INTEGER · read-write · current This object activates an additional check for incoming packets. If set to always (1), incoming packets are only accepted if return packets sent back to their source IP address would be sent over the same interface. This prevents packets being passed from untrusted interfaces to this interface. If set to interface-dependent (2), this check will be performed only if enabled for the associated ingress interface (see ipExtIfBackRtVerify). If set to never (2), this check will be never performed, regardless wether enabled or not for the associated interface.
| |||||||||||||
| SbiboExtAdmRerouteViaDefault | 1.3.6.1.4.1.272.4.22.1.12 | INTEGER | RW | ||||||||||
scalar · INTEGER · read-write · current This object controls the behaviour of the routing algorithm when a network route exists for routing a packet, but is temporarily unusable because the status of the associated interface prevents transmission. In such a case, the routing algorithm tries to select an alternate route to allow the packet to reach its destination. If set to disabled (1), default routes are discarded during the search for a suitable alternate route. If set to enabled (2), a default route may be selected for rerouting provided it is the most appropriate route available.
| |||||||||||||
| SbiboExtAdmGUILanguage | 1.3.6.1.4.1.272.4.22.1.13 | DisplayString (SIZE (3)) | RW | ||||||||||
scalar · DisplayString (SIZE (3)) · read-write · current This object specifies the language used within the graphical user interface (currently new web based interface only). Valid abbreviations (in principle) are defined in ISO 639-2. | |||||||||||||
| SbiboExtAdmIpLogging | 1.3.6.1.4.1.272.4.22.1.14 | Bits | RW | ||||||||||
scalar · Bits · read-write · current This bitfield enables logging of dedicated subsystems
within the INET subject:
nat : NAT
tcppr : TCP processing (MSS clamping, ...)
dns : DNS
ips : IP session management
acl : Local Services Access Control
.
| |||||||||||||
| SbiboExtAdmRadiusNasId | 1.3.6.1.4.1.272.4.22.1.15 | DisplayString | RW | ||||||||||
scalar · DisplayString · read-write · current An administratively-assigned NAS identifier for this managed node. If configured this variable is used for each RADIUS request in order to set the associated NAS-IDENTIFIER RADIUS attribute value. | |||||||||||||
| SbiboExtAdmConfigSaveDate | 1.3.6.1.4.1.272.4.22.1.17 | Date | RO | ||||||||||
scalar · Date · read-only · current Timestamp when configuration gets/got saved (system local time). | |||||||||||||
| SbiboExtAdmSnmpShellPrompt | 1.3.6.1.4.1.272.4.22.1.18 | DisplayString | RW | ||||||||||
scalar · DisplayString · read-write · current Defines prompt of application SNMP shell.
A set of escape sequences is defined with escape character
being a backslash '\':
- 'e': gets replaced by escape character (0x1b)
- 'h': gets replaced by system name (i.e. host)
- 'T': can be used for MIB context replacements ...
%n -> current MIB table name
%# -> current MIB table number
%g -> current MIB group number
A longer string can be put within parentheses '(' ')'
causing the whole string to be left out if no context
is available instead of only the MIB variables.
Examples, assuming context MIB table 'system':
String Yields
------------------------+------------------------
\T%n | 'system'
\T( MIB{%n/#%#/g:%g\)}) | ' MIB{system/#1/g:1}'
- 'l': gets replaced by log name (i.e. user, normally admin)
- 'd': can be used for date/time replacements with '%'
escaped replacements ...
%C -> century
%d -> day of month (01..31)
%D -> date in format 'MM/DD/YY'
%F -> date in format YYYY-MM-DD
%H -> hour (00..23)
%I -> hour (01..12)
%j -> day of year (1..366)
%k -> hour ( 0..23)
%l -> hour ( 1..12)
%m -> month (01..12)
%M -> minute (00..59)
%p -> AM/PM
%P -> am/pm
%R -> 24 hour time in format HH:MM
%s -> seconds sincs 1970-01-01 00:00:00 UTC
%S -> seconds (00..59)
%T -> 24 hour time in format HH:MM:SS
%u -> day of week (1..7)
%w -> day of week (0..6)
%y -> year (last two digits, 00..99)
%Y -> year
A longer string can be put within parentheses '(' ')'
to save repetitions of leading '\d' for every
replacement.
- 'u': gets replaced by system's uptime in format
[D ]HH:MM:SS
Default value is '\h:\t(%n)> '. | |||||||||||||
| SbiboExtAdmMinArpLifeTime | 1.3.6.1.4.1.272.4.22.1.19 | INTEGER (0..86400) | RW | ||||||||||
scalar · INTEGER (0..86400) · read-write · current This object defines the minimum lifetime (in seconds) of ipNetToMediaTable entries.
| |||||||||||||
| SbiboExtAdmInitialGUIView | 1.3.6.1.4.1.272.4.22.1.21 | INTEGER | RW | ||||||||||
scalar · INTEGER · read-write · current This object controls the initial GUI behavior for admin login for boxes with supports of 'GUI Views' and 'Initial Operation View' in GUI. full-access: show the complete admin navigation. user: show the user view initial-operation: show the initial operation view. If initial operation is not supported fall back to user view, if user view is not supported fall back to full access.
| |||||||||||||
| NchkUpdSrv | 1.3.6.1.4.1.272.4.22.1.22 | ||||||||||||
| NchkUpdSrvAdmin | 1.3.6.1.4.1.272.4.22.1.22.1 | ||||||||||||
| SchkUpdSrvAdminStatus | 1.3.6.1.4.1.272.4.22.1.22.1.1 | INTEGER | RW | ||||||||||
scalar · INTEGER · read-write · current Tells when to fetch/process the XML-file-contents pointed at
by chkUpdSrvAdminOperURL (if not empty string).
disabled: Clear chkUpdSrvAdminOperURL and supress further
fetch-attempts.
ondemand: Fetch at system-start and at every change of
chkUpdSrvAdminOperURL (unless empty string).
periodic: In addition to 'ondemand', fetch also periodically
with specified chkUpdSrvAdminInterval.
checknow: Fetch now and switch-back AdminStatus to previous
value (i.e. to disabled, ondemand, periodic).
| |||||||||||||
| SchkUpdSrvAdminInterval | 1.3.6.1.4.1.272.4.22.1.22.1.2 | INTEGER (1..8191) | RW | ||||||||||
scalar · INTEGER (1..8191) · read-write · current Period in hours for checking for available updates. Default value is once a week (7 * 24 = 168 hours). Ignored if chkUpdSrvAdminStatus is NOT periodic.
| |||||||||||||
| SchkUpdSrvAdminURL | 1.3.6.1.4.1.272.4.22.1.22.1.3 | DisplayString | RW | ||||||||||
scalar · DisplayString · read-write · current Sets location of the XML description file, UNLESS value is set already at compile-time (see chkUpdSrvAdminOperURL). | |||||||||||||
| SchkUpdSrvAdminOperURL | 1.3.6.1.4.1.272.4.22.1.22.1.4 | DisplayString | RO | ||||||||||
scalar · DisplayString · read-only · current Shows location of the XML description file, coming from either chkUpdSrvAdminURL or fixed compile-time-URL, or forced to empty string if chkUpdSrvAdminStatus is disabled. If resulting string is empty then chkUpdSrvTable is filled for biboExtAdmUpdatePath instead, unless also empty. | |||||||||||||
| SchkUpdSrvAdminDefaultDigestType | 1.3.6.1.4.1.272.4.22.1.22.1.5 | INTEGER | RW | ||||||||||
scalar · INTEGER · read-write · current Default digest-checking-method (if not specified in XML-file)
| |||||||||||||
| SchkUpdSrvAdminOperStatus | 1.3.6.1.4.1.272.4.22.1.22.1.6 | INTEGER | RO | ||||||||||
scalar · INTEGER · read-only · current Current activity and state.
| |||||||||||||
| SchkUpdSrvAdminLastSuccessfulCheckTime | 1.3.6.1.4.1.272.4.22.1.22.1.7 | Date | RO | ||||||||||
scalar · Date · read-only · current If not 0, tells when chkUpdSrvTable was last updated successfully for contents coming from either chkUpdSrvAdminOperURL or biboExtAdmUpdatePath. Is reset to 0 whenever chkUpdSrvAdminOperURL changes. | |||||||||||||
| SchkUpdSrvAdminLastFailedCheckTime | 1.3.6.1.4.1.272.4.22.1.22.1.8 | Date | RO | ||||||||||
scalar · Date · read-only · current If not 0, tells time of last unsuccessful update-attempt. If bigger than chkUpdSrvAdminLastSuccessfulCheckTime then retries are scheduled (see chkUpdSrvAdminLastFailedTries). Is reset to 0 whenever chkUpdSrvAdminOperURL changes. | |||||||||||||
| SchkUpdSrvAdminLastFailedCheckInfo | 1.3.6.1.4.1.272.4.22.1.22.1.9 | DisplayString | RO | ||||||||||
scalar · DisplayString · read-only · current Display-status of last unsuccessful update-attempt. (Not updated for successful checks.) Is flushed to empty whenever chkUpdSrvAdminOperURL changes. | |||||||||||||
| SchkUpdSrvAdminActiveProductClass | 1.3.6.1.4.1.272.4.22.1.22.1.10 | DisplayString | RO | ||||||||||
scalar · DisplayString · read-only · current Currently active product-class. | |||||||||||||
| SchkUpdSrvAdminAlternativeProductClass | 1.3.6.1.4.1.272.4.22.1.22.1.11 | DisplayString | RO | ||||||||||
scalar · DisplayString · read-only · current Alternative product-class (empty if unknown). | |||||||||||||
| SchkUpdSrvAdminLastFailedTries | 1.3.6.1.4.1.272.4.22.1.22.1.12 | INTEGER | RO | ||||||||||
scalar · INTEGER · read-only · current If not 0, tells that retries are scheduled for latest failed update-check, and how many tries have been done yet (see also chkUpdSrvAdminLastFailedCheckTime for related timestamp). Is reset to 0 whenever update-check succeeds or restarts (e.g. due to changed chkUpdSrvAdminOperURL). | |||||||||||||
| TchkUpdSrvTable | 1.3.6.1.4.1.272.4.22.1.22.2 | NA | |||||||||||
table · not-accessible · current List of available update-files. When update-command is called with dummy-URL 'http:', it looks for a matching default-entry in this table to get a proper chkUpdSrvDownloadLink. | |||||||||||||
| RchkUpdSrvEntry | 1.3.6.1.4.1.272.4.22.1.22.2.1 | NA | |||||||||||
| CchkUpdSrvIndex | 1.3.6.1.4.1.272.4.22.1.22.2.1.1 | INTEGER | RO | ||||||||||
column · INTEGER · read-only · current Unique identification of the entry. | |||||||||||||
| CchkUpdSrvProductClass | 1.3.6.1.4.1.272.4.22.1.22.2.1.2 | DisplayString | RO | ||||||||||
column · DisplayString · read-only · current Product-class for file. | |||||||||||||
| CchkUpdSrvFileType | 1.3.6.1.4.1.272.4.22.1.22.2.1.3 | INTEGER | RO | ||||||||||
column · INTEGER · read-only · current Type of file.
| |||||||||||||
| CchkUpdSrvFileDescr | 1.3.6.1.4.1.272.4.22.1.22.2.1.4 | DisplayString (SIZE (0..64)) | RO | ||||||||||
column · DisplayString (SIZE (0..64)) · read-only · current Additional file-description, used for language and third party files. | |||||||||||||
| CchkUpdSrvFileVersion | 1.3.6.1.4.1.272.4.22.1.22.2.1.5 | DisplayString (SIZE (0..64)) | RO | ||||||||||
column · DisplayString (SIZE (0..64)) · read-only · current Version of file (empty if unknown). | |||||||||||||
| CchkUpdSrvFileDigestType | 1.3.6.1.4.1.272.4.22.1.22.2.1.6 | INTEGER | RO | ||||||||||
column · INTEGER · read-only · current Method to be used for digest-checking
| |||||||||||||
| CchkUpdSrvFileDigestValue | 1.3.6.1.4.1.272.4.22.1.22.2.1.7 | DisplayString | RO | ||||||||||
column · DisplayString · read-only · current Hash/signature for this file, depending on digest-type. | |||||||||||||
| CchkUpdSrvDownloadLink | 1.3.6.1.4.1.272.4.22.1.22.2.1.8 | DisplayString | RO | ||||||||||
column · DisplayString · read-only · current URL for downloading this file. | |||||||||||||
| CchkUpdSrvRelNoteLink | 1.3.6.1.4.1.272.4.22.1.22.2.1.9 | DisplayString | RO | ||||||||||
column · DisplayString · read-only · current URL for downloading release-notes (if any) for this file. | |||||||||||||
| CchkUpdSrvFileUpdatable | 1.3.6.1.4.1.272.4.22.1.22.2.1.10 | INTEGER | RO | ||||||||||
column · INTEGER · read-only · current Tells if system can be updated with this file. false: Update will not work or have no effect true: Update will have effect unknown: No info available (e.g. unknown file-version)
| |||||||||||||
| IbiboMIB | 1.3.6.1.4.1.272.250 | ||||||||||||
identity MIB module for vendor specific box definitions.
Note: bibo stands for BinTec box stemming from the times where
the company was still called BinTec. | |||||||||||||
Traps / Notifications
- biboAdmTrapACrdDown
1.3.6.1.4.1.272.4.1.43.0.3 - biboAdmTrapACrdFailed
1.3.6.1.4.1.272.4.1.43.0.5 - biboAdmTrapACrdRunning
1.3.6.1.4.1.272.4.1.43.0.4 - biboAdmTrapACrdStopped
1.3.6.1.4.1.272.4.1.43.0.6 - biboAdmTrapACrdTempCritical
1.3.6.1.4.1.272.4.1.43.0.1 - biboAdmTrapACrdTempOk
1.3.6.1.4.1.272.4.1.43.0.2